Operation Manual

Operation Manual
Digital PA Combination System
PAC-5000A/5600
DIGITAL PA COMBINATION SYSTEM
Welcome
A personal welcome to you from the management and employees of Inter-M
All of the co-workers here at Inter-M are dedicated to providing excellent products with inherently good value,
and we are delighted you have purchased one of our products.
We sincerely trust this product will provide years of satisfactory service, but if anything is not to your complete
satisfaction, we will endeavor to make things right.
Welcome to Inter-M, and thank you for becoming part of our worldwide extended family!
Caution
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
This symbol is intended to alert the user to the
presence of important operation and maintenance
(servicing) instructions in the literature accompanying
the appliance.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WaRninG
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
Caution: To prevent electric shock do not use this (polarized) plug with
an extension cord, receptacle or other outlet unless the blades
can be fully inserted to prevent blade exposure.
Attentions: Pour prévenir les chocs électriques ne pas utiliser cette
fiche polarisée avec un prolongateur, une prise de courant
on une autre sortie de courant, sauf si les lames peuvent
étre insérées à fond sans en laisser aucune partie à
découvert.
*WARNING FOR YOUR PROTECTION PLEASE READ THE FOLLOWING-WATER AND MOISTURE: Unit should not be used near water(e.g.
near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken so than objects do
not fall and liquids are not spilled into the enclosure through openings.
*Do not install this equipment in a confined space such as a book case or similar unit.
*This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such vases, shall be placed on the apparatus.
*This apparatus shall be connected to a mains socket outlet with a protective earthing connection.
*It has heed to be easy to disconnect the device. To disconnect the device from power, separate AC input cable from inlet or unplug the AC Cord.
Caution
*These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing
other than that contained in the operating instructions unless you are qualified to do so.
notE
*This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
DIGITAL PA COMBINATION SYSTEM
Contents
Unpacking .......................................................................................................................................2
Installation
Environment....................................................................................................................................2
Important Safety Instructions.............................................................................................................2
Features............................................................................................................................................3
Front Panel ......................................................................................................................................5
Rear Panel .......................................................................................................................................9
Operating Method .......................................................................................................................17
1. Before Using the System.............................................................................................................17
2. System Operation......................................................................................................................17
3. FM Tuner Operations.................................................................................................................18
4. MEDIA (CD/USB/DRP) Operation ..............................................................................................19
5. Add-on Operation Methods .......................................................................................................23
Connections ...................................................................................................................................27
Block Diagram ..............................................................................................................................28
Specifications ................................................................................................................................30
Service
Procedures....................................................................................................................................33
Schematic .....................................................................................................................................33
Parts List .......................................................................................................................................33
Variations and Options ...............................................................................................................33
Warranty .......................................................................................................................................33
PAC-5000A/5600
1
DIGITAL PA COMBINATION SYSTEM
Unpacking
Although your PAC-5000A/5600 is neither complicated nor difficult to operate, we recommend you take a few
minutes to read this brief manual and familiarize yourself with the important information regarding product
features, setup and operation.
As with most electronic devices, we strongly recommend you retain the original packaging. In the unlikely event
the product must be returned for servicing, the original packaging (or reasonable equivalent) is required.
Installation
Environment
Never place this product in an environment which could alter its performance or reduce its service life. Such
environments usually include high levels of heat, dust, moisture, and vibration.
IMPORTANT SAFETY INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
S3125A
S3125A
2
PAC-5000A/5600
DIGITAL PA COMBINATION SYSTEM
Features
- BUDGET AND SPACE SAVING INSTALLATION
The System incorporates most of the current PA functions plus Emergency and normal broadcasting abilities thus
allowing budget and space saving installation.
- DUAL BROADCASTING SYSTEM
With two-channel (300W+300W) high power amplifier built-in, dual broadcasting is possible in 24 Zones
separated by A/B channels.
- DIGITAL PROCESSING & DIGITAL AMPLIFIER
Adopting the use of CLASS-D Amplifier to reduce the total weight, power consumption and operating
temperature.
- BUILT IN VARIOUS SOUND SOURCES
The system provides FM Tuner, Media (CD/DRP/USB) player and two AUX (1,2) inputs for flexible usage.
- LIFE TIME EXTENSION OF CD MECHANISM
Has the ability to copy the music CD to the internal memory (DRP) to extend the life of the CD mechanism.
- USB HOSTING
MP3/WMA files on the USB memory can be copied to internal memory (DRP) or play directly.
- REMOTE CONTROL SUPPORT
PAC-5000A: Using RS-232C terminal allows remote control from Windows application on the PC.
PAC-5600: Using a network port for remote control from the web page is possible.
※ However, CD EJECT, TUNER Memory operation including each input level volume cannot be controlled.
- SYSTEM EXPANSION
System can be expanded up to 4 units via the LINK-IN/OUT terminals while sharing the audio source. (MASTER
1 Unit, SLAVE 4 Units)
- 24 CHANNEL SPEAKER SELECT (ZONE 1~ZONE 24)
The system provides 24 channel zone selections, which can be divided into two groups for multiple broadcast
areas and with system expansion total of 120 channels can be operated.
- EQ ADJUSTMENT
EQ adjustment is possible with built-in DSP.
- REMOTE MIC CONNECTION
Maximum of four remote MICs can be connected to one unit of the system, and with installation of key pad one
of the four units can be used up to maximum of 120 channels.
- BUILT IN MONITOR SPEAKER
One can monitor the broadcast content with a built-in monitor speaker.
PAC-5000A/5600
3
DIGITAL PA COMBINATION SYSTEM
- EMERGENCY POWER AND BATTERY CHARGING
System has battery charge connect terminal for battery charge to provide emergency power.
- FIRE DETECTION AND EMERGENCY BROADCASTING
The system provides 24 channel sensor input terminals for automatic fire alarm broadcasting. It also provides
the recording function of personalized alarm message.
- CHIME AND SIREN
Built-in Chime (4 Scale, 2 Scale) and Sire (Continuous Wave) can be used to broadcast in the event of an
emergency. Also users can change the Siren and Chime.
- INCREASED INPUTS MIC/LINE
System has 5 MIC/LINE input jacks that can be selected by a switch, phantom power (DC 24V) is also supplied
for enhanced compatibility.
- BUILT IN EM MICROPHONE (CONDENSER MICROPHONE)
EM microphone is built-in to the front panel making emergency broadcast a simple task.
- MP3 / WMA SUPPORT
Unit supports MP3/WMA and CD-DA.
- PRE-PROGRAMMED BROADCASTING
Broadcast can be pre-programmed by either PC TIMER or stored source.
PAC-5600: Pre-Program Maximum 50/Holiday Maximum 30 (Stored Source, PC TIMER).
PAC-5000A: Pre-Program Maximum 100 (PC TIMER).
(Pre-Programs can be controlled by broadcasting web pages and Windows applications)
- RACK MOUNT
Rack mount bracket is included with the unit.
- SPEAKER LINE CHECK FUNCTION (PAC-5600 ONLY)
Check connected speaker for functionality.
- BATTERY CHECK FUNCTION (PAC-5600 ONLY)
Check the condition of the battery.
4
PAC-5000A/5600
DIGITAL PA COMBINATION SYSTEM
Front Panel
1. POWER SWITCH
Switch turns the unit On or Off.
2. GROUP SELECT BUTTON (GROUP – A, GROUP – B)
Group A/B speaker zone select/deselect button.
3. NOR / EM BUTTON
Normal or Emergency select button.
※ Normal : Green LED, Emergency : Red LED
4. SPEAKER ZONE SELECT BUTTON (ZONE 1 ~ ZONE 24)
Group A/B Speaker Zone select button. LED will light when turned on.
※ Group A : Green LED, Group B : Orange LED, Emergency : Red LED
5. SIREN BUTTON (SIREN 1, SIREN 2)
Continuous Siren (SIREN 1), Wave Siren (SIREN 2).
6. MONITOR SPEAKER SELECT BUTTON (MONITOR A/B)
The Button is used to monitor Speaker Outputs of Group A or B.
1) Press button in succession to change. Group A (Green LED) → Group B (Orange LED) → Off.
2) Hold the button down to change the output level (Low/High).
7. CHIME SELECT BUTTON
4 Scale or 2 Scale chime button, useful before and after the broadcast.
※Note: MIC Function must be on to run a chime.
PAC-5000A/5600
5
DIGITAL PA COMBINATION SYSTEM
8. EMERGENCY BROADCAST TEST BUTTON (EM TEST)
Test button to confirm the broadcast sound in the event of fire. In EM (Emergency) mode press and hold the
button down to broadcast stored source and press down again to cancel the playback. You can also select
separate speaker ZONE at this time.
9. BGM INPUT INDICATOR LED
The LED displays the currently selected BGM input and are divided into groups A and B.
10. BGM INPUT SELECT BUTTON (FUN.)
Select desired input source to either Group A or B. Changes in the order of TUNER → MEDIA → AUX1 →
AUX2 each time the button is pressed.
11. MIC/LINE SELECT BUTTON (A, B) AND INDICATOR LED
MIC/LINE select button. LED will light when pressed.
※NOTE: MIC/LINE 1 has the priority over MIC/LINE 2.
12. EQ ADJUSTMENT
Adjusts EQ levels: BASS (100Hz), MIDDLE (1kHz), TREBLE (10kHz).
13. INPUT VOLUME LEVEL ADJUSTMENT
Adjusts the input volume levels of MIC/LINE 1, MIC/LINE 2, AUX1, AUX2, TUNER, and MEDIA
(CD/USB/DRP).
14. MASTER VOLUME CONTROL
Adjust main volume of the system. Depending on the selection (A, AB, B) control method may change.
15. SELECT VOLUME CONTROL BUTTON (A, AB, B)
Speaker output level for each Group can be adjusted independently.
- A Button: A Group only
- B Button: B Group only
- AB Button: A and B together
16. CD SLOT
Insert CD into the slot.
17. EJECT BUTTON
Eject the CD.
18. USB TERMINAL
Terminal is to connect the USB. MP3/WMA files can be played and can also COPY the files from USB to
DRP.
19. EMERGENCY MIC (EM MIC) AND OPERATION SWITCH (MIC SW)
Built-in condenser microphone is used for EM (Emergency Broadcast) during FIRE. In EM mode, hold down
the (MIC SW) to operate.
6
PAC-5000A/5600
DIGITAL PA COMBINATION SYSTEM
20. MEDIA FUN. BUTTON
MEDIA (CD/USB/DRP) select button. Each time the button is pressed, changes in the order of CD → USB →
DRP.
- CD Mode: CD Play
- USB Mode: Play files stored in USB
- DRP Mode: Play files stored in the internal memory
21. INFO. BUTTON
- Access additional features of the system.
※Please refer to the “Additional Information” section.
22. RANDOM BUTTON
Play random selections.
23. REPEAT BUTTON
Repeat play selected file.
24. COPY BUTTON
Start copy CD, USB files to the DRP.
※Note : Due to copyright laws, cannot copy files to CD/USB from DRP.
25. DELETE BUTTON
Button to delete the files stored in the DRP.
26. DISPLAY WINDOW
A window that displays the current operating system information.
27. I◀◀ (▼PRESET) / ▶▶I (PRESET▲) BUTTON
- MEDIA (CD/DRP/USB) Track selection button.
- TUNER Select stored radio stations.
- Used to select the system information and additional information.
28. ▶LL (PLAY / PAUSE) / FM MUTE BUTTON
- MEDIA (CD/DRP/USB) Play or Pause. Press ▶ll once to Play and once more to Pause.
- In TUNER Mode it is used to MUTE the weak signal stations.
29. ◀◀ (▼TUNING) / ▶▶ (TUNING▲) BUTTON
- MEDIA (CD/DRP/USB) Fast Forward or Rewind Button.
- In TUNER Mode, used to seek stations. Press once to move one step or press and hold to tune
automatically.
30. ■ (STOP) / MEMO BUTTON
- MEDIA (CD/DRP/USB) Stop Play.
- MEMO: In TUNER Mode, used to store stations in Memory.
PAC-5000A/5600
7
DIGITAL PA COMBINATION SYSTEM
31. NUMBER BUTTONS (0~9)
Number buttons are used to enter numbers to search for tracks and to enter radio frequencies.
32. SYSTEM OPERATION INDICATOR
Displays the system operations such as Emergency Broadcast (EM), Fire (FIRE), reserved broadcast (PC),
remote microphone broadcast (RM) and general broadcast (BGM).
8
PAC-5000A/5600
DIGITAL PA COMBINATION SYSTEM
Rear Panel
-PAC-5000A
11 12 13
2
16 14
18
15
20 22 24 23
25 26
21
⠍⨲ᴝ㛍 : YH09015-15001 / MSIP-REM-IMK-PAC-5000A
⢱㔝ᬚ⼂@Z@⚹ᖩ⚹⍱⌹ㇱ
ᬽ@ᐍ@ᬚ@Z@PAC-5000A
MAIN POWER
⢪ാ⢙◪@Z@100-240V~ 50/60Hz
⢱⤅⠥ᬚ@
൵ಲ⩕❥㎕@TEL : 1588-7074
SD CARD A
ON
OFF
ABN 35 007 573 417
SD CARD B
EM
RS-232C
SERVICE
RM 1
FAULT OUT
REMOTE MIC (RM-6024)
RM 2
RM 3
A
RM 4
B COM
ADDRESS ID
MODEL NO. PAC-5000A
DIGITAL PA COMBINATION SYSTEM
BATTERY INPUT
DC 24-27V
MAX 30A
AUX 1
CONTACT
MIC / LINE 2
MIC / LINE 1
POST-OUT B
PHANTOM
MIC
LINE
PHANTOM
MIC
LINE
PHANTOM
MIC
LINE
E.M
MADE IN KOREA
SIG G
+
-
A
B
+ -
G
+
-
COM
SW
PRIORITY INPUT
PHANTOM
MIC
LINE
A
S N
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION : RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE.
PHANTOM
MIC
LINE
1
2
3
4
5
6
FIRE COM
7
8
9
10
11
12
SW
AUX 1
AUX 2 REC OUT
PC TIMER
B
FIRE
PD
FM ANT
OUT
UNBAL
/ 75Ω
EM MIC
AMP OUTPUT : 300W + 300W (100V, 33.3Ω / 70V, 16.6Ω)
LINK
IN
1. MASTER
2~5. SLAVE
POST-OUT A
28
27
13
14
15
16
17
18
19
20
21
22
23
24
13
14
15
16
17
18
19
20
21
22
23
24
ಥ⢙⟭@➙㙭⠉@⠝⟑፝@ḙ㘉㗭⩕@ᩝ⎂⍱⚹N
㟉⨝ᨑ@෥㛭㗵@൒❅@Ჭᕱ⍱@ᑮ⠑⢪ാ⟙@⅁✾㗭⎂⍱⚹N
AC INPUT
100-240V~ 50/60Hz, 135W
EXT CHIME
AMP IN
4-WIRE ATT
A
A
+ -
+ -
B
24V - A
24V - B
A
+ -
+ -
B
COM - A
COM - B
AMP OUT
COM
B
CLASS 2 WIRING
1
2
3
4
5
6
7
8
9
10
11
12
OUTPUT
VOLTAGE
AC FUSE
T3.15AL / 250V
100V
70V
CAUTION : TO REDUCE THE RISK OF FIRE REPLACE ONLY WITH SAME TYPE FUSE. UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE.
7
5
3
1
8
4
6
9
10
17 19
-PAC-5600
2
11
12 13
14 16
15
18
20
21 23
24 26 28
27
25
22
SD CARD A
MAIN POWER
ON
OFF
SD CARD B
EM
NETWORK
SERVICE
RM 1
FAULT OUT
REMOTE MIC (RM-6024)
RM 2
RM 3
A
RM 4
B COM
ADDRESS ID
LINK
UNBAL
/ 75Ω
EM MIC
MIC / LINE 2
MIC / LINE 1
POST-OUT B
PHANTOM
MIC
LINE
SIG G
PHANTOM
MIC
LINE
PHANTOM
MIC
LINE
PHANTOM
MIC
LINE
PHANTOM
MIC
LINE
A
E.M
PD
1
2
3
4
5
6
FIRE COM
7
8
9
10
11
12
4-WIRE ATT
A
+ -
+ -
A
+ -
+ -
AMP OUT
4
B
B
24V - A
24V - B
COM
COM - A
56
-
SW
A
AUX 2 REC OUT
B
1
2
3
4
5
6
7
8
9
10
11
12
G
+
-
SW
PC TIMER
COM
B
FIRE
A
AC FUSE
1
EXT CHIME
AMP IN
+
PRIORITY INPUT
+ -
AC INPUT
100-240V~ 50/60Hz, 135W
FM ANT
OUT
AUX 1
BATTERY INPUT
DC 24-27V
MAX 30A
3
IN
1. MASTER
2~5. SLAVE
POST-OUT A
13
14
15
16
17
18
19
20
21
22
23
24
13
14
15
16
17
18
19
20
21
22
23
24
B
CLASS 2 WIRING
OUTPUT
VOLTAGE
COM - B
100V
7 89
70V
10
17 19
1. POWER INPUT (AC INLET)
Connect AC Power cable. Before connecting, make sure that the power voltage matches the operating
voltage of the device. (100-240VAC~ 50/60Hz)
PAC-5000A/5600
9
DIGITAL PA COMBINATION SYSTEM
2. DC POWER INPUT AND BATTERY CHARGE TERMINAL
The emergency power supply and battery charging port can connect DC 24V battery.
- Priority is given to AC power when both AC and DC power are both input. DC power is activated when
AC is cut off.
- When operating in emergency power mode and the battery voltage is about 20V, system operation
indicator “DC” will flash and if the voltage drops below 19V, system will be in standby mode to protect the
battery.
※Notices
1. When in standby mode due to low voltage, battery can be recharged (20V) by AC power.
2. Before connecting the battery, please check for proper polarity (+,–).
3. Please note that it may cause electric sparks when connecting the battery.
3. AC FUSE
If any problem occurs with the AC power, fuse in the unit will cut the AC power to protect the unit. When
replacing the fuse, replace with the same capacity as listed.
4. AMP IN/OUT TERMINAL
External amplifier input terminals are located in the back of the unit when separate/additional power
amplifier is needed.
※ Note: When using built-in amplifier, input/output terminals must be connected to each other.
1) AMP OUT (AMP OUT)
- Connect built-in amplifier (100V/33.3Ω or 70V/16.6Ω) terminals to AMP IN terminals.
- Pay attention to Group A,B and polarity (+, –) connections.
2) AMP IN (AMP IN)
- Amplifier out terminal which can be connected to (AMP OUT) or connect to external amplifier. The input
can be used for local broadcast through speaker ZONE selection button on the front panel.
3) How to Connect
- When using only the built-in amplifier:
AMP IN
AMP OUT (A, B) to the AMP IN (A, B), while observing
correct polarity (+,–).
- When using both Internal and External Amplifier:
Connect an output of the two groups to the amplifier input
and the external Amplifier output to the other group input.
※Caution: When connecting an external amplifier, connect
HIGH IMPEDANCE output to AMP IN terminal.
Do not connect amplifiers rated 1200W or
higher. Also, each ZONE output must be 500W
or less.
10
PAC-5000A/5600
A
+ -
+ -
B
A
+ -
+ -
B
AMP OUT
AMP IN
A
+ -
+ -
B
A
+ -
+ -
B
AMP OUT
DIGITAL PA COMBINATION SYSTEM
5. EXT CHIME/ FIRE COM
EXT CHIME: Terminal to operate the CHIME2 using an external contact.
FIRE COM: FIRE SENSOR common ground input terminal.
6. 24V – A/24V – B TERMINAL
Terminal used when 4-wire Attenuator is used. SPEAKER OUTPUT terminals (+, –) and 24V – A(or 24V – B),
are used to connect COM port.
7. COM TERMINAL
24V – A/24V – B’s GND terminal.
8. CONTROL OUT TERMINAL
- EM (Emergency)
The terminal is used to control external devices when the broadcasting mode is changed to emergency
broadcast (EM/Fire/Pri), and the contact is closed regardless of speaker zone settings.
- PD (Power Distributor)
It is used to control power distributor remotely. By connecting to the remote control terminal of the PD,
contact output is made when there is a signal output in any speaker zone, regardless of broadcasting
mode (EM/Normal)
9. OUTPUT VOLTAGE SELECT SWITCH
100V / 70V output select switch.
※NOTE : Before using the switch, make sure the speaker impedance is proper. (10.3 Please refer to the
nominal output impedance information).
10. SPEAKER OUTPUT CONNECT TERMINAL
The speaker output terminals of each ZONE (1~24). General Broadcast (2wire), Emergency Broadcast
(3wire), ATTENUATOR (4wire) are possible. Terminals are set from left, +, –, and E.
1) Speaker Output Signal
- Normal Broadcast: Connection to (+, –) will produce output.
- EM / FIRE Broadcast: Connection to (+, –)/(E, –) will produce EM broadcast output.
2) Speaker Connections
- When connecting the speakers, disconnect the power cord from the wall outlet. Depending on the type
of speakers in use, select the appropriate speaker terminals on rear panel.
3) Rated Power Output and Impedance
Contents
Output/Impedance
100V
70V
Group A (12 ZONE)
100V/33.3Ω(300W)
70V/16.6Ω(300W)
Group B (12 ZONE)
100V/33.3Ω(300W)
70V/16.6Ω(300W)
PAC-5000A/5600
11
DIGITAL PA COMBINATION SYSTEM
HIGH IMPEDANCE Speaker Installation
1
2
3
4
5
6
HOT
19
20
21
22
23
24
COM
※ ZONE OUTPUT 1~24 ZONE (Caution when connecting).
Group A, B, respectively (12 ZONE) the sum of power output is not over (300W + 300W).
11. MAIN POWER SWITCH (MAIN POWER)
The switch is used to turn On and Off the AC power.
12. POST OUTPUT Terminal (POST-OUT A/B)
Terminal is used to record sound from this unit and to connect to an external amplifier.
13. SERVICE TERMINAL
Used for maintenance/service of the unit.
14. TELECOMMUNICATION TERMINAL
- PAC-5600: NETWORK Terminal
Supports 10/100 Base-Tx as a network terminal, remote control is possible by accessing the web page.
- Standard TIA/EIA 568B standard terminated CAT5 cables used to connbect the PAC-5600.
[ TOP VIEW ]
[ FRONT VIEW ]
8.Brown
7.W/Brown
6.Green
5.W/Blue
4.Blue
3.W/Green
2.Orange
1.W/Orange
UTP
12
PAC-5000A/5600
1
8
DIRECT
[ CABLE COLOR ORDER ]
1
1
8
CROSS
[CABLE COLOR ORDER]
8
1
8
DIGITAL PA COMBINATION SYSTEM
- PAC-5000A: RS-232C Terminal
RS-232 SERIAL terminal for remote control access. Remote control is possible with the PC program
provided separately.
Pin
Purpose
1
X
2
Receive
3
Transmit
4
X
5
Ground
6-9
X
※For how to use the remote control, please refer to the SOFTWARE MANUAL.
15. SD MEMORY CARD SLOT (SD CARD 1/2)
Insert SD memory card with stored emergency broadcast sound source.
※Change the sound according to ones preferences.
16. LINE / MIC INPUTS AND INPUT SELECTION SWITCH
Usage of the input terminal is changed depending on the position selected by the input switch.
- LINE: LINE Input.
- MIC: Can be used as a general dynamic microphone input.
- PHANTOM: Condenser microphone input and provides DC 24V to the input terminal.
※MIC/LINE 1 input takes priority over MIC/ LINE 2 input.
17. FIRE SENSOR INPUT TERMINAL
Contact input terminals working in conjunction with fire receiver to output a fire emergency broadcast.
Each area has 3 input terminals to configure a group of upper, lower and or ground floor.
(Emergency Broadcast sound source is stored in SD memory card.)
Fire Signal
1st floor contact
2nd floor contact
Per diagram when the fire signal is received connect so that the proper channel is activated to send
emergency broadcast.
For example: 1st floor 1-4 channels are activated. 2nd floor 1-6 channels are activated. If both 1st and 2nd
floors are activated at the same time, 1-6 channels will transmit emergency broadcast.
In the above example case when 1st and 2nd floor are connected to 1-4 channel together ① 1st floor ②
2nd floor are connected. When multiple contacts are connected to same contact take extra care to connect
each one independently.
PAC-5000A/5600
13
DIGITAL PA COMBINATION SYSTEM
Fire contact Macro functions can be set with web (PAC-5600) or PC program (PAC-5000A). For detailed
instructions please refer to the SOFTWARE MANUAL.
※Note: When input comes in during standby mode, emergency broadcast system turns on and broadcasts
to pre-selected ZONE speakers.
18. REMOTE MIC CONNECT TERMINAL (RM 1 ~ RM 4)
Remote MIC (RM-6024) connect terminal. RM1~RM4 (Max 4 can be connected for use).
* PIN OUT Detail
Pin No.
1
2
3
4
5
6
7
8
Functions
RS-422 Data - RX+
RS-422 Data - RXRS-422 Data - TXLive Data Input
GND
RS-422 Data - TX+
Balanced Audio Output - HOT
Balanced Audio Output - COLD
- RM1 of RM1-RM4 terminal can be expanded up to 120 locations with optional KEYPAD (RM-6012KP).
※Note: When system is in SLAVE MODE, remote MIC function cannot be used.
19. PRIORITY INPUT TERMINAL
PRIORITY INPUT terminal that accepts input signals and contact point. SW +, –. When signal is received to
the terminal, in order of preference stops the broadcast and broadcasts the signal received in PRIORITY
INPUT to all ZONE.
20. FAULT OUT TERMINAL
Terminal that sends information of fault in the amplifier or in speaker line. Connect of FAULT OUT terminal
will be closed in situations as following.
PAC-5000A: Amplifier protection is activated when a amplifier malfunction is detected.
PAC-5600: When speaker lines are shorted (Please refer to page 24 for more information of SPEAKER LINE
CHECK function.)
21. EM MIC / SWITCH CONNECT TERMINAL (EM MIC)
Terminal is used when external MIC is used instead of EM MIC (built-in front panel). (MIC sold separately)
※ Note: When connecting external microphone, please observe the pin specifications.
22. ADDRESS SET SWITCH (ADDRESS ID)
Switch intended to specify the ADDRESS of each set for the expansion of the unit.
SET
MASTER
SLAVE1
SLAVE2
SLAVE3
SLAVE4
1
ON
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
DIP SWITCH
3
OFF
OFF
ON
OFF
OFF
4
OFF
OFF
OFF
ON
OFF
5
OFF
OFF
OFF
OFF
ON
ALLOCATED ZONE
1~24 ZONE
25~48 ZONE
49~72 ZONE
73~96 ZONE
97~120 ZONE
※ Note: In SLAVE MODE setting, if the numbers are duplicated it may cause abnormal operations.
14
PAC-5000A/5600
DIGITAL PA COMBINATION SYSTEM
23. LINK IN / LINK OUT TERMINAL
The terminal is used to expand the system up to 4 SLAVE units (Total 120 ZONE) can be connected.
Configured by MASTER and SLAVE system, SLAVE will share the output of the MASTER unit.
1) LINK IN Terminal
Terminal to receive the sound source and control signals from previous system for system expansion.
* PIN OUT Specification
Pin No.
1
2
3
4
5
6
7
8
Pin Name
GR-A-INGR-A-IN+
GND
GR-B-INGR-B-IN+
GND
CONTROL-A
CONTROL-B
Functions
Balanced Group-A-Cold
Balanced Group-A-Hot
Ground
Balanced Group-B-Cold
Balanced Group-B-Hot
Ground
RS-485 Data-A
RS-485 Data-B
2) LINK OUT Terminal
Terminal to send the sound source and control signals to next system for system expansion.
* PIN OUT Specification
Pin No.
1
2
3
4
5
6
7
8
Pin Name
GR-A-OUTGR-A-OUT+
GND
GR-B-OUTGR-B-OUT+
GND
CONTROL-A
CONTROL-B
Functions
Balanced Group-A-Cold
Balanced Group-A-Hot
Ground
Balanced Group-B-Cold
Balanced Group-B-Hot
Ground
RS-485 Data-A
RS-485 Data-B
3) System Set up and Connection
- Set the ADDRESS setting switch to the proper usage (MASTER/SLAVE 1~4) of the system. Turn the
power off and turn on to apply the settings.
- System set to SLAVE is displayed as “SLAVE (1~4)” in the front display window.
- The system set to SLAVE cannot use its own sources.
⠍⨲ᴝ㛍 : YH09015-15001 / MSIP-REM-IMK-PAC-5000A
⢱㔝ᬚ⼂@Z@⚹ᖩ⚹⍱⌹ㇱ
ᬽ@ᐍ@ᬚ@Z@PAC-5000A
MAIN POWER
⢪ാ⢙◪@Z@100-240V~ 50/60Hz
⢱⤅⠥ᬚ@
൵ಲ⩕❥㎕@TEL : 1588-7074
ABN 35 007 573 417
ON
OFF
SD CARD A
SD CARD B
EM
NETWORK
SERVICE
RM 1
FAULT OUT
REMOTE MIC (RM-6024)
RM 2
A
RM 4
RM 3
B COM
ADDRESS ID
BATTERY INPUT
DC 24-27V
MAX 30A
MIC / LINE 2
MIC / LINE 1
PHANTOM
MIC
LINE
SIG G
PHANTOM
MIC
LINE
PHANTOM
MIC
LINE
PHANTOM
MIC
LINE
MADE IN KOREA
+
-
A
G
+
-
SW
+ -
E.M
AUX 1
CONTACT
PD
1
2
3
4
5
6
FIRE COM
7
8
9
10
11
12
FM ANT
OUT
AUX 1
AUX 2 REC OUT
B
PRIORITY INPUT
PHANTOM
MIC
LINE
A
S N
LINK
UNBAL
/ 75Ω
EM MIC
POST-OUT B
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION : RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE.
IN
1. MASTER
2~5. SLAVE
POST-OUT A
MODEL NO. PAC-5000A
DIGITAL PA COMBINATION SYSTEM
AMP OUTPUT : 300W + 300W (100V, 33.3Ω / 70V, 16.6Ω)
PC TIMER
COM
SW
B
FIRE
13
14
15
16
17
18
19
20
21
22
23
24
15
16
17
18
22
23
24
ಥ⢙⟭@➙㙭⠉@⠝⟑፝@ḙ㘉㗭⩕@ᩝ⎂⍱⚹N
㟉⨝ᨑ@෥㛭㗵@൒❅@Ჭᕱ⍱@ᑮ⠑⢪ാ⟙@⅁✾㗭⎂⍱⚹N
AC INPUT
100-240V~ 50/60Hz, 135W
⠍⨲ᴝ㛍 : YH09015-15001 / MSIP-REM-IMK-PAC-5000A
⢱㔝ᬚ⼂@Z@⚹ᖩ⚹⍱⌹ㇱ
ᬽ@ᐍ@ᬚ@Z@PAC-5000A
MAIN POWER
⢪ാ⢙◪@Z@100-240V~ 50/60Hz
⢱⤅⠥ᬚ@
൵ಲ⩕❥㎕@
TEL : 1588-7074
AC FUSE
T3.15AL / 250V
ABN 35 007 573 417
ON
OFF
EXT CHIME
AMP IN
4-WIRE ATT
A
A
+ -
+ -
AMP OUT
A
+ -
POST-OUT A
24V - A
B
NETWORK
SERVICE
+ -
COM - A
B
SD- CARD
A
B
24V
COM
SD1CARD B 2
OUTPUT EM
VOLTAGE
COM - B
100V
70V
3
RM 1
7
4
5
RM 2
FAULT OUT
8
9
10
A
RM 4
RM 3
CLASS 2 WIRING
6
REMOTE MIC (RM-6024)
11
B
B COM
12
19
MIC / LINE 2
MIC / LINE 1
POST-OUT B
PHANTOM
MIC
LINE
PHANTOM
MIC
LINE
PHANTOM
MIC
LINE
PHANTOM
MIC
LINE
E.M
MADE IN KOREA
PD
AUX 1
CONTACT
SIG G
+
-
A
B
+ -
G
+
-
COM
SW
PRIORITY INPUT
PHANTOM
MIC
LINE
A
S N
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION : RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE.
1
2
3
4
5
6
7
8
9
10
11
12
SD1CARD B 2
3
4
5
6
LINK
20
EM MIC
DIGITAL PA COMBINATION SYSTEM
AMP OUTPUT : 300W + 300W (100V, 33.3Ω / 70V, 16.6Ω)
BATTERY INPUT
DC 24-27V
MAX 30A
14
IN
1. MASTER
2~5. SLAVE
CAUTION : TO REDUCE THE RISK OF FIRE REPLACE ONLY WITH SAME TYPE FUSE. UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE.
MODEL NO. PAC-5000A
13
ADDRESS ID
FM ANT
OUT
21
AUX 1
UNBAL
/ 75Ω
AUX 2 REC OUT
PC TIMER
SW
B
FIRE
13
14
15
16
17
18
19
20
21
22
23
24
13
14
15
16
17
18
22
23
24
ಥ⢙⟭@➙㙭⠉@⠝⟑፝@ḙ㘉㗭⩕@ᩝ⎂⍱⚹N
㟉⨝ᨑ@෥㛭㗵@൒❅@Ჭᕱ⍱@ᑮ⠑⢪ാ⟙@⅁✾㗭⎂⍱⚹N
AC INPUT
100-240V~ 50/60Hz, 135W
⠍⨲ᴝ㛍 : YH09015-15001 / MSIP-REM-IMK-PAC-5000A
⢱㔝ᬚ⼂@Z@⚹ᖩ⚹⍱⌹ㇱ
ᬽ@ᐍ@ᬚ@Z@PAC-5000A
MAIN POWER
⢪ാ⢙◪@Z@100-240V~ 50/60Hz
⢱⤅⠥ᬚ@
൵ಲ⩕❥㎕@TEL : 1588-7074
AC FUSE
T3.15AL / 250V
ABN 35 007 573 417
ON
OFF
EXT CHIME
AMP IN
FIRE COM
4-WIRE ATT
A
A
+ -
+ -
AMP OUT
NETWORK
SERVICE
A
+ -
POST-OUT A
24V - A
B
+ -
COM
COM - A
B
SD CARD A
24V - B
COM - B
EM
OUTPUT
VOLTAGE
100V
70V
RM 1
7
REMOTE MIC (RM-6024)
8
RM 2
9
10
11
FAULT OUT
A
RM 4
RM 3
B
CLASS 2 WIRING
B COM
ADDRESS ID
12
19
CAUTION : TO REDUCE THE RISK OF FIRE REPLACE ONLY WITH SAME TYPE FUSE. UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE.
MODEL NO. PAC-5000A
AMP OUTPUT : 300W + 300W (100V, 33.3Ω / 70V, 16.6Ω)
MIC / LINE 2
MIC / LINE 1
POST-OUT B
PHANTOM
MIC
LINE
SIG G
PHANTOM
MIC
LINE
PHANTOM
MIC
LINE
PHANTOM
MIC
LINE
+ -
A
S N
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION : RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE.
MADE IN KOREA
E.M
1
PD
2
+
AUX 1
CONTACT
-
SW
A
PRIORITY INPUT
PHANTOM
MIC
LINE
3
4
5
6
LINK
20
EM MIC
DIGITAL PA COMBINATION SYSTEM
BATTERY INPUT
DC 24-27V
MAX 30A
IN
1. MASTER
2~5. SLAVE
G
+
-
SW
FM ANT
OUT
21
AUX 1
UNBAL
/ 75Ω
AUX 2 REC OUT
B
PC TIMER
COM
B
FIRE
13
14
15
16
17
18
19
20
21
22
23
24
13
14
15
16
17
18
19
20
21
22
23
24
ಥ⢙⟭@➙㙭⠉@⠝⟑፝@ḙ㘉㗭⩕@ᩝ⎂⍱⚹N
㟉⨝ᨑ@෥㛭㗵@൒❅@Ჭᕱ⍱@ᑮ⠑⢪ാ⟙@⅁✾㗭⎂⍱⚹N
AC INPUT
100-240V~ 50/60Hz, 135W
EXT CHIME
AMP IN
FIRE COM
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
4-WIRE ATT
A
A
+ -
+ -
B
24V - A
24V - B
A
+ -
+ -
B
COM - A
COM - B
AMP OUT
COM
AC FUSE
T3.15AL / 250V
B
CLASS 2 WIRING
OUTPUT
VOLTAGE
100V
70V
CAUTION : TO REDUCE THE RISK OF FIRE REPLACE ONLY WITH SAME TYPE FUSE. UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE.
PAC-5000A/5600
15
DIGITAL PA COMBINATION SYSTEM
24. AUX1 INPUT JACKS AND CONTACTS
Ability to use AUX1 as BGM input from an external source input. Priority is same as BGM.
A - COM Contact Input, A group’s BGM will be selected to AUX1.
B - COM Contact Input, B group’s BGM will be selected to AUX1.
25. AUX INPUT TERMINAL
Multiple external source devices (CD, DECK, TUNER, etc.) can be connected and input volume adjustment is
on the front panel.
26. REC OUT TERMINAL
The terminal for recording the output of Group A,B to the external recording device.
27. RESERVED BROADCAST INPUT TERMINAL (PC TIMER)
The terminal to receive audio signals from PC for playback in reserved broadcast.
28. FM ANTENNA TERMINAL (FM ANT)
Use the FM antenna supplied with the product, 75Ω coaxial cable can also be connected if the signal is
weak and produces noise.
16
PAC-5000A/5600
DIGITAL PA COMBINATION SYSTEM
Operating Method
1. Before using the system
1) Set all the volumes to minimum level before connecting to a wall outlet.
2) Please make sure that the speaker and the input terminals are connected properly.
In particular, make sure that the AMP input / output jacks on the rear panel are connected properly.
3) Confirm the settings of MASTER, SLAVE modes.
4) The red LED on power button on the front panel will blink and stop when the main power switch on back is
turned on.
5) Pressing the power button on front panel will turn on the display window.
6) Adjust both the input and main volume to operate the system.
2. System Operation
1) Dual Broadcasting
System can broadcast to two different areas (Group A and Group B) with unique broadcasts to each Group.
- Input selection by group
Select an input by using the input selection button (FUN) for each group.
Each time the button is pressed, input changes in the order of TUNER → MEDIA → AUX1 → AUX2.
Example) Group A: TUNER Broadcast, Group B: MEDIA (CD) Broadcast.
☜
- Main Volume Control by Group
Use the mode selection button on the front panel to adjust the speaker output level by Group.
☞
- MIC and Chime Broadcast
• MIC broadcasting can be separate for Group A and Group B.
• Press the MIC/LINE button for a specific group to broadcast to.
☞
➡
• Before pressing the Chime button, adjust the input volume level properly.
※Note: For Chime operation, Group must be selected using the MIC/LINE button.
PAC-5000A/5600
17
DIGITAL PA COMBINATION SYSTEM
2) How to check Emergency Broadcast Sound
• In EM (Emergency) mode press and hold EM TEST button to hear through the main and monitor
speakers.
3) System Remote Control Method
Please refer to the SOFTWARE MANUAL.
※PC Program, Software MANUAL can be downloaded from (www.inter-m.com).
3. FM TUNER Operation
1) How to Auto/Manual tune radio frequencies
- Use either Group A or B input button to light the LED on TUNER.
- TUNING ▼ / ▲ (Frequency DOWN/UP). Use Up/Down buttons to find desired frequency.
• Auto Tune : TUNING ▼ / ▲ (DOWN/UP) Holding down the button will automatically find and tune in
the stations. Once tuned in “TUNED” will display.
• Manual Tune : TUNING ▼ / ▲ (DOWN/UP) Pressing the button briefly once will increase/decrease
the frequency by one step. If possible frequency is found “TUNED” will display and play.
2) How to store and recall stored stations
- TUNING ▼ / ▲ (Frequency DOWN/UP). Find or Select desired stations.
- Press MEMO button and MEMORY will display along with preset number.
- Press PRESET ▼ / ▲ button or numbers (0~9) button to select preset location and pressing MEMO
button will store the frequency in the preset location.
➡
- Using above steps up to 40 stations can be stored in preset memory.
- Recall the stored stations by pressing the PRESET ▼ / ▲ buttons.
➡
3) FM Antenna Installation
Find the best possible location with the best reception for the FM antenna. However, within the city,
industrial areas, or high voltage transmission lines will cause excessive noise or weak signal. In this case it
is best to install an outdoor antenna with 75Ω connecting cable.
18
PAC-5000A/5600
DIGITAL PA COMBINATION SYSTEM
4) FM MUTE Function
No display of TUNED indicates no broadcast or weak/noisy signals. Pressing FM MUTE button will
display “AUTO” and bypass all weak or noisy stations.
➡
When the normal broadcast signal is received TUNED is displayed and the broadcast is automatically
resumed.
※Note: In some cases TUNED display will be lit due to the interference from other equipment such as CDP. In
this case, install or move the equipment away from the system.
4. MEDIA (CD/USB/DRP) Operation
1) Input select mode
- Use either Group A of B input button to light the LED on MEDIA.
- MEDIA FUN Button. Each time button is pressed, input changes in the order of CD → USB → DRP.
2) Play/Pause Function
- CD
• Able to play CD-DA/MP-3/WMA formats.
• Press MEDIA FUN button to select CD mode.
➡
• When the CD is inserted, reads the CD information and goes to standby mode displaying TOTAL songs
available.
Up to 499 songs is displayed and “NO DISC” is displayed when there is no CD present.
• ▶ll (Play/Pause) Press once to Play and once more to Pause.
• ▶ll (Play/Pause) Press again to cancel Pause and resume Play.
※Note: IF the disc is in poor condition or is a non-playback format, disc will be ejected automatically.
In this case it is not the system, please check the disc instead.
Only the 12cm size disc can be used. 8cm size disc cannot be used.
PAC-5000A/5600
19
DIGITAL PA COMBINATION SYSTEM
- USB
• Plays the files stored in a USB memory device.
• Press MEDIA FUN button to select USB mode.
➡
• When the USB device is inserted in the USB reader, reads the information and goes to standby mode
displaying TOTAL number of files available. If there is no USB device “NO USB” will display and “NO
FILE” when there is no file to read.
• ▶II (Play/Pause) Press once to Play and once more to Pause.
• ▶II (Play/Pause) Press again to cancel Pause and resume Play.
- DRP
• Plays the files stored in the internal memory.
• Press MEDIA FUN Button to select DRP mode.
➡
• Once in DRP mode, reads the information and goes to standby mode displaying TOTAL number of files
available.
If no files are available “NO FILE” will be displayed.
• ▶II (Play/Pause) Press once to Play and once more to Pause.
• ▶II (Play/Pause) Press again to cancel Pause and resume Play.
3) REPEAT Function
Each time REPEAT button is pressed mode changes in order of REPEAT 1 → REPEAT GROUP(USB) →
REPEAT ALL → OFF.
- REPEAT 1 Function
Press the REPEAT button once “REPEAT 1” is displayed and selected song is played repeatedly.
- REPEAT GROUP Function
When REPEAT is double-clicked “REPEAT GROUP” is displayed and USB file folder is played repeatedly.
- REPEAT ALL Function
Press REPEAT three times “REPEAT ALL” is displayed and the entire disc is played repeatedly.
- OFF Mode
Disc is stopped after playing the entire disc once without repeat.
4) RANDOM Function
Songs are played in random order.
- In stop mode press RANDOM and “RANDOM” is displayed. Press ▶II (Play/Pause) button to play in
random order.
- Repeat playback is possible in REPEAT mode.
- Press RANDOM button once more to cancel the mode.
20
PAC-5000A/5600
DIGITAL PA COMBINATION SYSTEM
5) COPY Function
Ability of copying CD and USB source materials to the DRP(Internal Memory).
- CD COPY
• Ability to copy the contents of the CD to the DRP. CD playback and COPY is done at the same time.
• Using this feature can greatly extend the life of the CD mechanism as playback is sourced from internal
memory.
• Insert CD and press COPY button to switch to the CD COPY mode.
• Press I◀◀ (▼PRESET) / ▶▶I (PRESET▲) to select the folder to be stored.
• After selecting the file to COPY, press ▶II (Play/Pause) (screen shot below). Press ▶II (Play/Pause)
once more to start the COPY function. (New file will over-write existing file.)
➡
➡
- USB COPY
• Ability to copy the contents of USB to the DRP. No playback during COPY and the files are copied
sequentially.
• Insert USB and double-click the COPY button to switch to the USB COPY mode.
• Press I◀◀ (▼PRESET) / ▶▶I (PRESET▲) to select the folder to be stored.
• After selecting the file to COPY, press ▶II (Play/Pause) (screen shot below). Press ▶II (Play/Pause)
once more to start the COPY function.
➡
➡
※Notice: 1. When COPY starts the existing files stored in the folder will be deleted.
2. Playback order will be same as USB stored order. If specific playback order is needed,
create a new USB source with playback order before using COPY function.
- Press MEDIA FUN button to switch to DRP mode to verify the COPY content.
- Pressing the ■ (Pause) button during COPY will stop the copy function and save only up to the last
completed tracks.
PAC-5000A/5600
21
DIGITAL PA COMBINATION SYSTEM
6) DELETE (File Delete) Function
Function to delete unnecessary files from the DRP (internal memory).
- Folder Delete
• Press MEDIA button to select DPR.
• Pressing DELETE button will change to delete mode and “FOLDER1” is displayed.
• Press ▶▶ (SEARCH UP) button to select folder (FOLDER1~6) to be deleted.
• Select the folder to delete and press DELETE button, as shown below and use I◀◀ / ▶▶I button to
delete only the selected TRACK.
• In “DELETE TRACK” mode pressing DELETE button to use numeric(0~9) buttons to select delete TRACK
is possible.
• Select the TRACK to delete and press DELETE button, as shown below, press DELETE once more to
delete the TRACK.
➡
- FORMAT
• In “FOLDER1” mode press ▶▶ (SEARCH UP) button to select the FORMAT as shown below.
• After selecting FORMAT, press DELETE button, as shown below, and press DELETE to start the FORMAT
.
➡
22
PAC-5000A/5600
DIGITAL PA COMBINATION SYSTEM
5. Add-on Operation Methods
1) System Version Display Function
Display the system version.
- Press INFO button and press I◀◀ / ▶▶I button to verify “VER. #.#.#.#”.
2) System IP information display (PAC-5600 Only)
Display units’ IP information.
- Press INFO button and press I◀◀ / ▶▶I button to display system IP information.
3) BUZZER ON/OFF Setting
Able to turn On/Off the BUZZER sound each time a button is pressed.
- Press INFO button and press I◀◀ / ▶▶I button to select “BUZZER ON.
- Use ▶II button to select ON/OFF option. (Default setting is ON position.)
4) AUTO PLAY Function Setting
Function to auto-play a CD and stop when the main power is turned on.
- Press INFO button and press I◀◀ / ▶▶I button to select “AUTOPLAY ON”.
- Use ▶II button to select ON/OFF option. (Default setting is ON position.)
※NOTE: To use the AUTO PLAY, before powering off, selection must be set to CD.
PAC-5000A/5600
23
DIGITAL PA COMBINATION SYSTEM
5) SPEAKER LINE CHECK Function (PAC-5600 Only)
Function to check if the speaker line is connected properly.
- CONFIRM: Test to store the current speaker line connect state.
• Press INFO button and press I◀◀ / ▶▶I button to select “SPEAKER CONFIRM”.
• In “SPEAKER CONFIRM” mode, pressing ▶II will display blinking “LINE” in the system operation
indicator and measure impedance value of ZONE1~24 sequentially.
• After the measurement of each ZONE, LED status displays of each ZONE is displayed.
1
2
3
STATUS
OPEN
SHORT
NORMAL
LED COLOR
LED OFF
RED LED ON
GREEN LED ON
INFORMATION
Speakers are not connected
Shorted or Output Overload
Good working order
• Press ▶II button to save the settings and return to the original state.
- TEST: Displays the status of the line in comparison to the stored value from CONFIRM test.
• Press INFO button and press I◀◀ / ▶▶I button to select “SPEAKER TEST”.
• In “SPEAKER TEST” mode, pressing ▶II will display blinking “LINE” in the system operation indicator
and measure impedance value of ZONE1~24 sequentially.
• After the measurement of each ZONE, LED status displays of each ZONE is displayed.
1
2
3
4
STATUS
OPEN
SHORT
NORMAL
ABNORMAL
LED COLOR
LED OFF
RED LED ON
GREEN LED ON
ORANGE LED ON
INFORMATION
Speakers are not connected
Shorted or Output Overload
Good working order
Abnormal. Checking is necessary
• Press ▶II button to save the settings and return to the original state.
- After the line test, in case of SHORT conditioned ZONE, ZONE button will not work. ZONE button will
only work in NORMAL status state.
- During CONFIRM or TEST, pressing ▶II button will cancel CONFIRM or TEST operations.
24
PAC-5000A/5600
DIGITAL PA COMBINATION SYSTEM
6) Battery Check Function (PAC-5600 Only)
Check the currently connected emergency battery’s condition.
- CONFRIM: To check and store the battery condition as a reference.
• Push INFO button and push I◀◀ / ▶▶I button to select “BATTERY CONFIRM”.
• At “BATTERY CONFIRM” push ▶II button and “BATT” will flash and start the CONFIRM process.
• When the operation is complete, it will display “CONFIRM OK” and if process failed, “CONFIRM
ERROR” will be displayed.
※Notice
1. During the installation new battery should be used to perform CONFIRM check.
2. Test the battery after the installation and when the battery is fully charged.
3. Accurate measurement can only be achieved when there was no change (Types of Cable, Length,
etc) and no replacement of cable or reconnecting of the battery, otherwise TEST ERROR may occur.
- TEST: at CONFIRM system will compare stored value and display the status of the BATTERY.
• After pressing INFO button select I◀◀ / ▶▶I button to select BATTERY TEST.
• Pressing ▶II during “BATTERY TEST” mode will display blinking “BATT” and TEST will commence.
• Upon completion of TEST following will be displayed.
PAC-5000A/5600
25
DIGITAL PA COMBINATION SYSTEM
1
2
3
Display
GOOD
NOT BAD
BAD
Condition
The Best Condition.
Periodic CHECK is necessary.
Replace the battery.
7) System Initialization (PAC-5600 Only)
Reset the IP address and web page settings.
- IP default value: 192.168.1.99
- For web page settings, reservation broadcast, please refer to the SOFTWARE MANUAL for more details.
26
PAC-5000A/5600
DIGITAL PA COMBINATION SYSTEM
Connections
CD-6208
CD-6208
⠍⨲ᴝ㛍 : YH09015-15001 / MSIP-REM-IMK-PAC-5000A
⢱㔝ᬚ⼂@Z@⚹ᖩ⚹⍱⌹ㇱ
ᬽ@ᐍ@ᬚ@Z@PAC-5000A
MAIN POWER
⢪ാ⢙◪@Z@100-240V~ 50/60Hz
⢱⤅⠥ᬚ@
൵ಲ⩕❥㎕@TEL : 1588-7074
ABN 35 007 573 417
ON
OFF
MODEL NO. PAC-5000A
PAC-5600 (MASTER)
RM-6024
RS-232 (PAC-5000A)
NETWORK (PAC-5600)
SD CARD A
SD CARD B
EM
NETWORK
SERVICE
RM 1
FAULT OUT
REMOTE MIC (RM-6024)
RM 2
RM 3
A
RM 4
B COM
ADDRESS ID
DIGITAL PA COMBINATION SYSTEM
MIC / LINE 2
MIC / LINE 1
POST-OUT B
PHANTOM
MIC
LINE
PHANTOM
MIC
LINE
PHANTOM
MIC
LINE
MADE IN KOREA
E.M
AUX 1
CONTACT
SIG G
+
-
A
B
+ -
G
+
-
COM
SW
PRIORITY INPUT
PHANTOM
MIC
LINE
A
S N
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION : RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE.
PHANTOM
MIC
LINE
PD
1
2
3
4
5
6
FIRE COM
7
8
9
10
11
12
24V - B
1
2
3
4
5
6
7
8
9
10
11
12
LINK
FM ANT
OUT
UNBAL
/ 75Ω
EM MIC
AMP OUTPUT : 300W + 300W (100V, 33.3Ω / 70V, 16.6Ω)
BATTERY INPUT
DC 24-27V
MAX 30A
IN
1. MASTER
2~5. SLAVE
POST-OUT A
PAC-5600 (SLAVE)
SW
AUX 1
AUX 2 REC OUT
PC TIMER
B
FIRE
13
14
15
16
17
18
19
20
21
22
23
24
13
14
15
16
17
18
19
20
21
22
23
24
ಥ⢙⟭@➙㙭⠉@⠝⟑፝@ḙ㘉㗭⩕@ᩝ⎂⍱⚹N
㟉⨝ᨑ@෥㛭㗵@൒❅@Ჭᕱ⍱@ᑮ⠑⢪ാ⟙@⅁✾㗭⎂⍱⚹N
AC INPUT
100-240V~ 50/60Hz, 135W
EXT CHIME
AMP IN
4-WIRE ATT
A
A
+ -
+ -
AMP OUT
B
24V - A
COM
AC FUSE
T3.15AL / 250V
A
+ -
+ -
B
COM - A
COM - B
B
CLASS 2 WIRING
OUTPUT
VOLTAGE
100V
70V
CAUTION : TO REDUCE THE RISK OF FIRE REPLACE ONLY WITH SAME TYPE FUSE. UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE.
GROUP - A (300W)
GROUP - B (300W)
or
AMP (DPA-300D)
PAC-5000A/5600
27
28
PAC-5000A/5600
0,&/,1(
0,&/,1(
(0B0,&
(0B0,&
3&7,0(5
$8;
$8;
35,,1387
/,1.,1%
/,1.,1$
0,&/,1(
0,&/,1(
0,&/,1(
',*,7$/
$1$/2*
)0781(5
&'0(&+$
50
$8;G%9.2+0
0,&G%9.2+0
/,1(G%9.2+0
$8',2,1387
/('($
.(<($
$1$08;
&+8$57
/(''5,9(5
(0%
(0$
'27/('
/(''5,9(5
0$,1&38
$'&
'63
92/80(($
$1$08;
)5217&38
9)'
/,1.287%
/,1.287$
021,725$03
3$726(
3$726(
021B63.
5(&287B%
5(&287B$
3267287B%
3267287B$
'$03
'$03
$03287
$8',2287387
9
$03,1
6(1625,1387
6(1625,1387
; ,13876
),5(6(1625
=21(%86 =21(
63($.(5287
DIGITAL PA COMBINATION SYSTEM
Block Diagram
- PAC-5000A
',*,7$/
$1$/2*
0,&/,1(
(0B0,&
(0B0,&
3&7,0(5
$8;
$8;
35,,1387
/,1.,1%
/,1.,1$
0,&/,1(
0,&/,1(
0,&/,1(
0,&/,1(
)0781(5
&'0(&+$
50
$8;G%9.2+0
0,&G%9.2+0
/,1(G%9.2+0
$8',2,1387
5-
7,0(5
(0%
(0$
$1$08;
.(<($
/('($
3+<
1(7:25.
0$,1&38
/(''5,9(5
$8',2&2'(&
&+8$57
$'&
'63
'27/('
/(''5,9(5
92/80(($
$1$08;
)5217&38
9)'
/,1.287%
/,1.287$
021,725$03
$8',2287387
3$726(
3$726(
021B63.
5(&287B%
5(&287B$
3267287B%
3267287B$
'$03
'$03
$03287
9
$03,1
6(1625,1387
6(1625,1387
; ,13876
),5(6(1625
=21(%86 =21(
63($.(5287
DIGITAL PA COMBINATION SYSTEM
Block Diagram
- PAC-5600
PAC-5000A/5600
29
DIGITAL PA COMBINATION SYSTEM
Specifications
PAC-5000A
PAC-5600
AUX INPUT (AUX IN @ 1kHz, 100V/33.33Ω, 70V/16.6 Ω LOAD OUTPUT)
Rated Output (@ T.H.D 1%, GROUP A + GROUP B)
300W+300W
Input Sensitivity
-10 ± 3dBV
Signal-to-Noise Ratio (S/N)
>75dB
EQ Control (100Hz, 1kHz, 10kHz)
±10 ± 3dB
Frequency Range (1W Power Output, ±3dB)
50Hz ~ 20kHz
MIC/LINE 1~5 Input (MIC/LINE @ 1kHz, POST OUT)
MIC Input Sensitivity
-55 ± 3
MIC Signal-to-Noise Ratio (S/N)
>80dB
MIC Frequency Characteristics (80kHz LPF, 0±3dB)
50Hz ~ 20kHz
MIC Phantom Power
24V
MIC Total Harmonic Distortion (T.H.D)
<0.5%
LINE Input Sensitivity
-10 ± 3dBV
LINE Signal-to-Noise Ratio (S/N)
>80dB
LINE Total Harmonic Distortion (T.H.D)
<0.3%
CD (TEST CD 0dB, 1kHz @ REC OUT)
Signal-to-Noise Ratio (S/N)
>75dB
Frequency Characteristics (80kHz LPF, 0±3dB)
100Hz ~ 20kHz
TUNER (FM, 22.5kHz MOD @ REC OUT)
Signal-to Noise Ratio (S/N)
>55dB
Frequency Characteristics (80kHz LPF)
0±3dB
100Hz
-3±3dB
12kHz
OUTPUT LEVEL (AUX IN, INPUT -10dB/1kHz)
REC OUT
-10 ± 2dBV
POST OUT
0 ± 2dBV
PC CONTROL INTERFACE
Data Transmission Method
RS-232
10/100 Base- Tx
Transmission Distance
≤10M
≤500M
Cable Type
USB to 232 cable
Category 5 UTP Cable
LINK IN/OUT, REMOTE MIC (RM 1~RM 4) INTERFACE
Data Transmission Method
RS-485 Serial
Transmission Distance
≤500M
Cable Type
Category 5 UTP Cable
Priority Control
EM MIC > FIRE > PRIORITY INPUT > EM >
PC TIMER > REMOTE MIC >
SIREN, CHIME > MIC1 > MIC2~5 > BGM
Fire Sensor
24 Channel
30
PAC-5000A/5600
DIGITAL PA COMBINATION SYSTEM
PAC-5000A
Operating Temperature
Power Source
Power Consumption (1/8W)
Weight (SET)
Dimension (SET)
PAC-5600
-10°C ~ +40°C
AC 100–240V, 50/60Hz, DC 24V
135W
11.1kg/24.4lb
11.2kg/24.7lb
482(W)×177(H)×373(D)mm/19(W)x 7(H) x 14.7(D) in
* Design and specification are subject to be changed for the improvement of product quality without pre notice.
PAC-5000A/5600
31
DIGITAL PA COMBINATION SYSTEM
380
※ DIMENSIONS
14.5
177
440
32
PAC-5000A/5600
DIGITAL PA COMBINATION SYSTEM
Service
Procedures
Take steps to insure the problem is not related to operator error or other products within the system. Information
provided in the troubleshooting portion of this manual may help with this process. Once it is certain that the
problem is related to the product contact your warranty provider as described in the warranty section of this
manual.
Schematic
A Schematic is available by contacting your warranty provider.
Parts List
A Parts List is available by contacting your warranty provider.
Variations and Options
Variations
Products supplied through legitimate sources are compatible with local AC power requirements.
Options
No optional items are available for this product.
Warranty
Warranty terms and conditions vary by country and may not be the same for all products. Terms and conditions
of warranty for a given product may be determined first by locating the appropriate country which the product
was purchased in, then by locating the product type.
To obtain specific warranty information and available service locations contact Inter-M directly or the
authorized Inter-M Distributor for your specific country or region.
PAC-5000A/5600
33
Inter-M, Ltd. (Korea) began operations in 1983.
Since then, Inter-M has grown to become one of the largest manufacturers
of professional audio and commercial sound electronics equipment in the world.
Inter-M has gained worldwide recognition for its own branded products,
as well as private label manufacturing of electronics sold under other names (OEM).
The company is no longer just a Korean company, but rather a global company
that is truly international in scope, with factories and offices in Korea and China,
and sales and marketing operations located in Japan, Europe, and the U.S.A.
With more than 850 employees around the globe,
Inter-M is well-poised for further growth and expansion.
Inter-M Americas, INC.
13875 ARTESIA BLVD. CERRITOS, CA 90703 USA
TEL : +1-562-921-0313, FAX : +1-562-921-0370
Home Page : http://www.inter-m.net, E-mail : [email protected]
Inter-M Corporation
SEOUL OFFICE : 719, DOBONG-RO, DOBONG-GU, SEOUL, KOREA
TEL : +82-2-2289-8140~8, FAX : +82-2-2289-8149
Home Page : http://www.inter-m.com, E-mail : [email protected]
MaDE in KoREa
April 2015 137398