Aruba IAP-200 Series Instant Access Point Installation Guide

IAP-200 Series Instant Access Point
Installation Guide
The Aruba IAP-204 and IAP-205 wireless access points support the IEEE
802.11ac and 802.11n standards for high-performance WLAN. These access
points use MIMO (Multiple-in, Multiple-out) technology and other highthroughput mode techniques to deliver high-performance, 802.11n 2.4 GHz and
802.11ac 5 GHz functionality while simultaneously supporting legacy 802.11a/b/g
wireless services.The IAP-220 Series access point works only in conjunction
with a virtual controller
Figure 6 Gigabit Ethernet Port Pin-Out
Figure 2 IAP-200 Series Side View (IAP-204 shown)
ANT0
ANT1
1000Base-T Gigabit
Ethernet Port
RJ-45 Female
Pin-Out
1
2
3
4
5
6
7
8
The Aruba IAP-200 Series access point provides the following capabilities:





Wireless transceiver
Protocol-independent networking functionality
IEEE 802.11a/b/g/n/ac operation as a wireless access point
IEEE 802.11a/b/g/n/ac operation as a wireless air monitor
Compatibility with IEEE 802.3af PoE
The IAP-200 Series requires Aruba Instant 4.2 or later.
Signal Name
Function
BI_DA+
BI_DABI_DB+
BI_DC+
BI_DCBI_DBBI_DD+
BI_DD-
Bi-directional pair +A
Bi-directional pair -A
Bi-directional pair +B
Bi-directional pair +C
Bi-directional pair -C
Bi-directional pair -B
Bi-directional pair +D
Bi-directional pair -D
Aruba Networks, Inc., in compliance with governmental requirements, has
designed the IAP-200 Series access points so that only authorized network
administrators can change the settings. For more information about AP
configuration, refer to the Aruba Instant Quick Start Guide and Aruba
Instant User Guide.
DC Power Socket
!
If PoE is not available, an optional Aruba AP AC-DC adapter kit (sold separately)
can be used to power the IAP-200 Series.
External Antenna Connectors
The IAP-204 is equipped with two external antenna connectors. The connectors
are labeled ANT0 and ANT1, and correspond to radio chains 0 and 1.
Figure 3 IAP-200 Series Rear View
Additionally, a locally-sourced AC-to-DC adapter (or any DC source) can be used
to power this device, as long as it complies with all applicable local regulatory
requirements and the DC interface meets the following specifications:


Package Contents
12 VDC (+/- 5%)/18W
Center-positive 1.7/4.0 mm circular plug, 9.5 mm length
Reset Button

IAP-204 or IAP-205 Access Point

9/16" and 15/16” Ceiling Rail Adapters
The reset button can be used to return the AP to factory default settings. To reset
the AP:

Aruba Instant Quick Start Guide
1. Power off the AP.

Installation Guide (this document)
2. Press and hold the reset button using a small, narrow object, such as a
paperclip.
Inform your supplier if there are any incorrect, missing, or damaged parts. If
possible, retain the carton, including the original packing materials. Use
these materials to repack and return the unit to the supplier if needed.
3. Power-on the AP without releasing the reset button. The power LED will
flash within 5 seconds.
AP-204_02
4. Release the reset button.
IAP-200 Series Hardware Overview
The power LED will flash again within 15 seconds indicating that the reset is
completed. The AP will now continue to boot with the factory default settings.
Identifying Specific Installation Locations
You can mount the IAP-200 Series access point on a wall or on the ceiling. Use
the AP placement map generated by Aruba’s Airwave VisualRF Plan software
application to determine the proper installation location(s). Each location
should be as close as possible to the center of the intended coverage area and
should be free from obstructions or obvious sources of interference. These RF
absorbers/reflectors/interference sources will impact RF propagation and
should have been accounted for during the planning phase and adjusted for in
VisualRF plan.
Identifying Known RF Absorbers/Reflectors/Interference
Sources
Identifying known RF absorbers, reflectors, and interference sources while in
the field during the installation phase is critical. Make sure that these sources are
taken into consideration when you attach an AP to its fixed location. Examples
of sources that degrade RF performance include:

Figure 1 IAP-200 Series LEDs
Before You Begin


For optimal performance when using articulating direct-mount antennas,
professional installers must orient the antennas as pictured in Figure 4, below.
PW R
!
ENET 5GHz 2.4 GH z
Figure 4 IAP-204 Antenna Orientation
The IAP-200 Series is equipped with four LEDs that indicate the status of the
various components of the AP.



PWR: Indicates whether or not the IAP-200 Series is powered-on and shows
basic system status
ENET: Indicates the status of the IAP-200 Series’ Ethernet port
5 GHz: Indicates the status of the 802.11a/n/ac radio
2.4 GHz: Indicates the status of the 802.11b/g/n radio
!
LED
Color/State
Meaning
PWR
Off
No power to AP
Red
Error condition
Green - Flashing
AP booting
Green - Steady
AP ready
Off
Ethernet link unavailable
Yellow - Steady
10/100Mbps Ethernet link established
Green - Steady
1000Mbps Ethernet link established
Flashing
Ethernet link activity
Off
5 GHz radio disabled
Yellow - Steady
5 GHz radio enabled in non-HT WLAN mode
Green - Steady
5 GHz radio enabled in HT WLAN mode
Flashing - Green
5 GHz Air or Spectrum Monitor
Off
2.4 GHz radio disabled
Yellow - Steady
2.4 GHz radio enabled in non-HT WLAN
mode
Green - Steady
2.4 GHz radio enabled in HT WLAN mode
Flashing - Green
2.4 GHz Air or Spectrum Monitor
5 GHz
2.4 GHz

Installing the AP
Service to all Aruba Networks products should be performed by trained
service personnel only.
Produit réseau local radio basse puissance operant dans la bande
fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au Aruba Instant User
Guide pour les details des restrictions.
Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet.
Weitere Informationen bezlüglich Einschränkungen finden Sie im Aruba
Instant User Guide.
Using the Ceiling Rail Adapter
The IAP-200 Series ships with two ceiling rail adapters for 9/16” and 15/16”
ceiling rails. Additional wall mount adapters and ceiling rail adapters for other
rail styles are available as accessory kits.
!
Maximum supported weight of the ceiling rail adapter is 3.75 kg.
!
Make sure the AP fits securely on the ceiling tile rail when hanging the
device from the ceiling, because poor installation could cause it to fall onto
people or equipment.
Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare
riferimento alla Aruba Instant User Guide per avere informazioni detagliate
sulle restrizioni.
Table 1 IAP-200 Series Series LED Meanings
ENET

Cement and brick
Objects that contain water
Metal
Microwave ovens
Wireless phones and headsets
EU Statement:
Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands.
Please refer to the Aruba Instant User Guide for details on restrictions.
LEDs

FCC Statement: Improper termination of access points installed in the
United States (non-US model Regulatory Domain model/s) will be in
violation of the FCC grant of equipment authorization. Any such willful or
intentional violation may result in a requirement by the FCC for immediate
termination of operation and may be subject to forfeiture (47 CFR 1.80).
Console Port
AP Pre-Installation Checklist
The serial console port allows you to connect the AP to a serial terminal or a
laptop for direct local management. This port is an RJ-45 female connector with
the pinouts described in Figure 5. Connect it directly to a terminal or terminal
server using an Ethernet cable.
Before installing your IAP-200 Series IAP, ensure that you have the following:
Figure 5 Serial Port Pin-Out
Serial
Console Port
RJ-45 Female
Pin-Out
1
2
3
4
5
6
7
8
Direction
Input
Output
TxD
GND
GND
RxD
Ethernet Port
The IAP-200 Series is equipped with one 10/100/1000Base-T (RJ-45) auto-sensing,
MDI/MDX wired-network connectivity port. This port supports IEEE 802.3af
Power over Ethernet (PoE) compliance, accepting 48 VDC (nominal) as a
standard defined Powered Device (PD) from a Power Sourcing Equipment (PSE)
such as a PoE midspan injector, or network infrastructure that supports PoE.
The 10/100/1000 Mbps Ethernet port is on the rear of the AP. This port has RJ-45
female connectors with the pin-outs shown in Figure 6.


CAT5e or better UTP cable of required length
One of the following power sources:
 IEEE 802.3af-compliant Power over Ethernet (PoE) source. The POE
source can be any power source equipment (PSE) controller or midspan
PSE device
 Aruba AP AC-DC adapter kit (sold separately)
Summary of the Setup Process
Successful setup of an IAP-200 Series access point consists of five tasks, which
must be performed in this order:
1. Identify the specific installation location for each AP.
2. Install each AP.
3. Verify post-installation connectivity.
4. Configure the virtual controller. Refer to the Aruba Instant Quick Start
Guide.
Access points are radio transmission devices and as such are subject to
governmental regulation. Network administrators responsible for the
configuration and operation of access points must comply with local
broadcast regulations. Specifically, access points must use channel
assignm ents appropriate to the location in which the access point will be
used.
1. Pull the necessary cables through a prepared hole in the ceiling tile near
where the AP will be placed.
2. Place the adapter against the back of the AP with the adapter at an angle of
approximately 30 degrees to the tabs (see Figure 7).
3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure
7).
China RoHS
Figure 7 Attaching the Ceiling Rail Adapter
10
Aruba products also comply with China environmental declaration requirements
and are labeled with the “EFUP 10” label shown at the left.
Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz
and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt
WLAN devices.
해당무선설비는 전파혼신의 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다.
᳝↦᳝ᆇ⠽䋼ໄᯢ
Hazardous Materials Declaration
䚼ӊৡ⿄
(Parts)
⬉䏃ᵓ
(PCA Boards)
ᴎẄ㒘ӊ
(Mechanical Sub-Assemblies)
ƻ˖
᳝↦᳝ᆇ⠽䋼៪‫ܗ‬㋴(Hazardous Substance)
䬝
݁Ӌ䫀
໮⒈㘨㣃
&G
&U
3%%
EU Regulatory Conformance
䪙
3E
∲
+J
h
ƻ
ƻ
ƻ
ƻ
ƻ
h
ƻ
ƻ
ƻ
ƻ
ƻ
໮⒈Ѡ㣃䝮
3%'(
㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼ SJ/T11363-2006 ᷛ‫ޚ‬㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ
Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is
below the relevant threshold of the SJ/T11363-2006 standard.
h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7ᷛ‫ޚ‬㾘ᅮⱘ䰤䞣㽕∖DŽ
Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials
in the parts is above the relevant threshold of the SJ/T11363-2006 standard.
This product is CE marked according to the provisions of the R & TTE Directive
(1999/5/EC) - CE(!). Aruba Networks Inc., hereby declares that the APIN0204 / APIN0205 device
models are in compliance with the essential requirements and other relevant provisions of Directive
1999/5/EC -CE(!)
IAP-200 Series Instant
Access Point
The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at the
following location: http://support.arubanetworks.com
ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼DŽ
This table shows where these substances may be found in the supply chain of electronic information
products, as of the date of sale of the enclosed product.
ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ
՟བ⬉∴ऩ‫ܗ‬῵ഫ 䌈೼݊ѻકϞ
ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟‫ݠ‬Ё᠔㾘ᅮⱘᴵӊϟᎹ԰
The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are
per the symbol shown here. The Environment- Friendly Use Period is valid only when the
product is operated under the conditions defined in the product manual.
Canada
Installation Guide
(i)les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux;
(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 4705 725 MHz doit se conformer à la limite de p.i.r.e.;
4. If necessary, connect the console cable to the console port on the back of the
AP.
5. Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots
at approximately a 30-degree angle to the ceiling tile rail (see Figure 8). Make
sure that any cable slack is above the ceiling tile.
6. Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks
into place on the ceiling tile rail.
European Union RoHS
Aruba products also comply with the EU Restriction of Hazardous
Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of
specific hazardous materials in the manufacture of electrical and
electronic equipment. Specifically, restricted materials under the RoHS
Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury,
Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in
RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging
will be marked with the “RoHS” label shown at the left indicating conformance to this Directive.
(iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se
conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le
cas.
De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance
sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et
5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs
LAN-EL.
Web Support
Aucune émission n’est permise dans la bande 5 600-5 650 MHz. Jusqu’à
nouvel avis, les dispositifs visés par la présente annexe ne doivent pas être
en mesure d’émettre dans la bande 5 600-5 650 MHz, afin de protéger les
radars météorologiques d’Environnement Canada exploités dans cette
bande.
India RoHS
Figure 8 Mounting the AP
Contacting Aruba Networks
This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling)
Rules, governed by the Ministry of Environment & Forests, Government of India.
Main Site
http://www.arubanetworks.com
Support Site
https://support.arubanetworks.com
Airheads Social Forums and Knowledge Base
community.arubanetworks.com
North American Telephone
1-800-943-4526 (Toll Free)
1-408-754-1200
International Telephones
arubanetworks.com/support-services/aruba-supportprogram/contact-support/
Software Licensing Site
licensing.arubanetworks.com/login.php
Wireless Security Incident
Response Team (WSIRT)
arubanetworks.com/support/wsirt.php
Waste of Electrical and Electronic Equipment
AP-204_04
Aruba products at end of life are subject to separate collection and treatment
in the EU Member States, Norway, and Switzerland and therefore are marked
with the symbol shown at the left (crossed-out wheelie bin). The treatment
applied at end of life of these products in these countries shall comply with
the applicable national laws of countries implementing Directive 2002/96EC
on Waste of Electrical and Electronic Equipment (WEEE).
Déclaration concernant l'exposition aux rayonnements de
radiofréquences : cet équipement est conforme aux normes d'Industrie
Canada relatives aux limites d'exposition humaine aux radiofréquences. Cet
équipement doit être installé et utilisé à une distance minimale de 20 cm (7,9
pouces) entre le dispositif de radiocommunication et votre corps dans les
gammes de 2,4 GHz et 5 GHz. Cet émetteur-récepteur ne doit pas être
placé à proximité immédiate d'une autre antenne ou un d'autre émetteurrécepteur, ou ne doit pas être utilisé conjointement avec ceux-ci.
!
Support Email Addresses
Americas and APAC
[email protected]
Safety and Regulatory Compliance
EMEA
[email protected]
Networks provides a multi-language document that contains country-specific restrictions and
additional safety and regulatory information for all Aruba access points. This document can be
viewed or downloaded from the following location: www.arubanetworks.com/safety_addendum
Americas and APAC Support Email
[email protected]
WSIRT Email
Please email details of any security
problem found in an Aruba product.
[email protected]
Hong Kong
Philippines
Regulatory Model Names
7. On the IAP-204, install the external antennas according to the manufacturer’s
instructions, and connect the antennas to the antenna interfaces on the AP.
The following regulatory model names apply to the IAP-200 Series:


HK0011400942
정소출력 무선기기 ( 무선데이터통신시스템용 무선기기 )
Install cables in accordance with all applicable local and national regulations and
practices.
FCC
Type-Approval No.
ESD-1409139C
Copyright
IAP-204: APIN0204
IAP-205: APIN0205
Connecting Required Cables
Type-Approval No.
ESD-1409138C
Singapore
HK0011400943
DB101525
This device is electronically labeled. To view the FCC ID:
Verifying Post-Installation Connectivity
1.
Log into the virtual controller WebUI.
2.
Navigate to About.
The integrated LEDs on the AP can be used to verify that the AP is receiving
power and initializing successfully (see Table 1). Refer to the Aruba Instant
Quick Start Guide for further details on verifying post-installation network
connectivity.
!
Product Specifications
RF Radiation Exposure Statement: This equipment complies with FCC
RF radiation exposure limits. This equipment should be installed and
operated with a minimum distance of 7.9 inches (20 cm) between the
radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter
must not be co-located or operating in conjunction with any other antenna
or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this
device is restricted to indoor use to reduce the potential for harmful
interference with co-channel Mobile Satellite Systems.

Ethernet:
 1x 10/100/1000 auto-sensing Ethernet RJ-45 Interface
 MDI/MDX
 IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)
 Power over Ethernet (802.3af compliant), 48V DC (nominal) and 56V DC (maximum)/350mA
(see Figure 6 for pin configuration)
Power:
 12 VDC power interface, supports powering through an AC-to-DC power adapter
 POE support on Ethernet port: 802.3af-compliant POE sourcing devices
If a power adapter other than the one provided by Aruba Networks is used
in the US or Canada, it should be cULus (NRTL) Listed, with an output
rated 12 VDC, minimum 1.5A, marked “LPS” or “Class 2,” and suitable for
plugging into a standard power receptacle in the US and Canada.
For additional specifications on this product, please refer to the data sheet. The data sheet can be
found at www.arubanetworks.com.
Open Source Code
Certain Aruba products include Open Source software code developed by third parties, including software code
subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open
Source Licenses. The Open Source code used can be found at this site:
Medical
http://www.arubanetworks.com/open_source
1.
Equipment not suitable for use in the presence of flammable mixtures.
2.
End product system, including power supply, must be evaluated to IEC 60601-1-1 and IEC 606011 by the end user.
Legal Notice
3.
Wipe with a dry cloth, no additional maintenance required.
4.
No serviceable parts, the unit must be sent back to the manufacturer for repair.
5.
No modifications are allowed without Aruba approval.
第十二條
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大
功率或變更原設計之特性及功能。
Electrical

© 2013 Aruba Networks, Inc. AirWave®, Aruba Networks®, Aruba Mobility Management System®, Bluescanner,
For Wireless That Works®, Mobile Edge Architecture, People Move. Networks Must Follow., RFProtect®, The All
Wireless Workplace Is Now Open For Business, and The Mobile Edge Company® are trademarks of Aruba
Networks, Inc. All rights reserved. All other trademarks are the property of their respective owners.
The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate
other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for
this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against
it with respect to infringement of copyright on behalf of those vendors.
Warranty
This hardware product is protected by an Aruba warranty. For details, see Aruba Networks standard warranty
terms and conditions.
FCC Class B Part 15
第十四條
This device complies with Part 15 of the Federal Communications Commission (FCC) Rules.
Operation is subject to the following two conditions:
1.
This device may not cause harmful interference.
2.
This device must accept any interference received, including interference that may cause
undesired operation.
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有
干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電
機設備之干擾。
!
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
Korean EMC Class B Warning
이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며, 모든 지역
에서 사용할 수 있습니다.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause
interference harmful to radio communications.
If this equipment does cause interference, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
Proper Disposal of Aruba Equipment


Dispose of Aruba products per local regulations. For the most current information about Global
Environmental Compliance and Aruba products, see our website at www.arubanetworks.com.


Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio or TV technician for help.
Complies with the Class B limits for radio noise emissions as set out in the interference-causing
equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.
Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel
brouilleur du Canada.
www.arubanetworks.com
1344 Crossman Avenue
Sunnyvale, California 94089
Phone: 408.227.4500
Fax 408.227.4550
IAP-200 Series Instant Access Point | Installation Guide
Part Number 0511627-01 | July 2014