- Computers & electronics
- Computer components
- Chassis components
- Computer cases
- Fantec
- 1367
- Data Sheet
advertisement
FANTEC SRC-3116X07
3U STORAGE RACKMOUNT CHASSIS
16x 3.5" SATA/SAS BACKPLANE SLOTS
FANTEC SRC-SERIE
STORAGE RACKMOUNT CHASSIS
I. Specification:
Support SAS interface: for 3G backward compatibility.
Support SATA interface: for 3G backward compatibility.
Support hard disk 29pin female SAS and SATA II compatibility.
Support for host card SAS primary port or SATA II input port.
Support miniSAS36 pin host connector for SFF8087 connector
Support 4 port hard disk inrush current control and mosfet IC for Hot-swapping.
Support hard disk DC +12V, +5V and +3.3V.
Support 4 pcs 0603 SMD blue LED light on for hard disk insert.
support 4 pcs 0603 white Led light on for hard disk insert
support 4 pcs 0630 red Led light on for hard disk failure indicator.
(connect to Raid contral unit)
(SATA ready is high active, and SAS ready is low active)
Support 2 pcs power 180 deg big 4-pin D-type connectors.
Support 4 pcs external FAN speed monitoring and FAN failure buzzer alarm. (Buzzer on board).
Support FAN fail SMD LED active shown and external pin header.
Support FAN fail buzzer alarm external pin header.
Support external 2X2 pin header for FAN fail LED and mute switch.
Minimum Fan Speed Detection: The FAN IC fail frequency is below 40 Hz, which corresponds to a fan speed of approximately 1200 rpm.
The fan remains powered during a locked rotor or an under-speed failure condition.
-01-
2. Pin Assignment:
interface side
B
A
CD
A
A
Fan1, Fan2, Fan3, Fan4 3 pin wafer for FAN monitor pin out
E
3 2 1 3 : Tech
B
JP1,JP2 big 4P pin out
2 : +12V
1
VDD +12V
1 2 3 4
1 : GND
2
GND
3
GND
4
VCC +5V
CD miniSAS 36PIN connector
E
S1 DIP Switch pin out
Switch
ON
OFF
SW1 Sw2
55 C Mute enable
60 C Mute disable
-02-
2-1. Pin Assignment:
interface side
H.D.D 1 H.D.D 2 H.D.D 4
G
H.D.D 3
E1
F
H.D.D
1 2 3 4
F
JP4 External 2 X 2 Pin out
3 GND 4 Mout switch+
For fail buzzer alarm mute insert pin 3-4.
1 Fan fail LED 2 Fan fail LED
For FAN fail LED insert pin 1-2.
+
G
JP3 4 X 4 pin 2.54mm 180deg header pin out.
13 9 5 1
14 10 6 2
15 11 7 3
16 12 8 4
1
2
3
4
13
14
Card acces LED4-
15
16
Card acces LED4+
HDD4 p11 pin
GND
9
10
Card acces LED3-
11
HDD4 p11 pin
12
Card acces LED3+
GND
5
Card acces LED2+
6
Card acces LED2-
7
HDD4 p11 pin
8
GND
1
Card acces LED1+
2
Card acces LED1-
3
HDD4 p11 pin
4
GND
Default setting is insert short jumper to pin 2-3, 6-7, 10-11, 14-15 for
HDD access support.
13 9 5 1
14 10 6 2
15 11 7 3
16 12 8 4
If you need HBA card in put access LED, please remove short jumper, insert pin 1-2, 5-6, 9-10,13-14.
If you need HDD motor spin function, please insert short jumper to pin 3-4, 7-8, 11-12, 15-16
13 9 5 1
14 10 6 2
15 11 7 3
16 12 8 4
13 9 5 1
14 10 6 2
15 11 7 3
16 12 8 4
-03-
2-2. Pin Assignment:
H.D.D side
H H H
H
H
J1, J2, J3, J4 2 29pin female SAS and SATA II connector pin out
S1
S8
P1
P8
P15
GND
GND
V33
V5
V12
S2
S9
P2
P9
RP+
RS+
V33
V5
S3
S10
P3
P10
RP-
RS-
V3C
GND
S4
S11
P4
P1
GND
GND
GND
1 LED
S5
S12
P5
P12
TP-
TS-
GND
V-gate
S6
S13
P6
P13
TP+
TS+
GND
V12C
S7
S14
P7
P14
GND
GND
V5C
V12
-04-
-
05
-
Product details
Model no.:
Specification:
Drive bays:
Mainboard type:
Cooling:
Switch:
Controls:
Slot opening:
Backplane:
Speaker:
SRC-3116X 3U 16xSAS&SATA Backplane
3U IPC 660mm black aluminium open: 16x3,5" SATA/SAS hot swap, 1x5,25" Slim internal: 2x 3,5"
E-ATX / ATX / M-ATX (12" x 13")
4x 80mm hot-swap fans
2x 80mm ball bearing fan at rear
ON/OFF switch, system & alarm reset
LED's for ON/OFF switch and HDD-access
7 open slots at rear panel
16x SATA 3Gbit / SAS / SATA, 4x internal miniSAS 36 pin cnnector
0,4W built in
Material/ color of chassis: 1,2mm SGCC zinc-coated steel black
Material/ color of front bezel: anodized aluminium black / blue
Material/ color of handle: steel / silver
Front connectors:
Accessories including:
2x USB connectors
2x Firewire connectors
USB connector cable with circuit diagram screws
Power supply:
Optional accessories: without power supply (optional) sliding rails package:
SRC-SR26"
Consists of 2x 26" mounting rails
Dimensions (w x d x h): 481 x 660 x 133 mm
Certifications: FCC, CE, RoHS
Weight / piece (kg): 15
Package (piece / carton): 1
Description: 19" industrial PC chassis for installation in 19" rackmount cabinet.
Rugged construction and high-grade processing.
Technical details are subject to changes.
-
06
-
-
07
-
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project