ViziT VIZIT-M440C Operating Instruction

VIZIT-M440C is a colour monitor intended for use in VIZIT video doorphones.

1

9

6

4

1.

2 .

3.

4.

5.

6.

7 .

8.

9.

10.

Handset

DOOR OPEN button

Increase value button

Decrease value button

Preset buttons:

-

-

ring tone volume

- select ring tone brightness saturation

LED indicators of a selected preset button

Switch to extra camera button

MONITOR button

Power LED

Screen

Figure 1 Appearance and controls layout

PARTS LIST

Monitor

- 440 C x 1

Operating Instruction x 3

Fasteners x 3

Concrete Insert 6х30 x 1

10

5

3

2

8

7

VIZIT-M440C

SAFETY INSTRUCTIONS

CAUTION ! The Monitor does not contain voltage above 27V .

Do not perform any connections or repair when the power is on.

Take care not to spill any liquids or chemically active substances on the product.

Unplug the power supply unit before cleaning the monitor. Clean by wiping with dry soft cloth. Do not use any liquid cleaners, aerosol cleaners or abrasive agents.

Do not attempt to service the product by yourself. Please refer all services to qualified service personnel.

FEATURES v v v v v v v v v v v v

Operation with two doorstations and extra camera (commutator BKM-440 required)

Operation with one doorstation, door bell button and extra camera (commutator BKM-440 not required)

Calls from doorstation and door bell button

Duplex intercom

Remote door unlocking with the button

Door zone video monitoring

Activation of individual / storey doorstation by subscriber (duplex intercom and video monitoring)

5 ring tones, individual ring tone for each doorstation and door bell button.

3 ring volume levels

Individual image brightness and saturation for each doorstation and extra camera

LED indication of operating modes

INSTALLATION

4

1

2

3

6

1 Connecting terminals

2 Recess for cables

3

4

DC IN to connect power supply unit SA03010029

Inlets for cables

5 Socket for handset jack

6 Fixing lugs

Figure 2 Rear view

4

5

Choose the position for monitor Recommended altitude is 150 cm from the floor to the monitor center .

1

1 2

85

2

3

85

57

Refer to page 25 for Mounting Pattern.

3 supplied with your monitor.

3

Connect the wires to the terminals of your monitor as shown in Fig. 4-7.

Match the monitor’s fixing lugs with the screws in the wall, and hook the monitor on the screws.

Connect the handset to the monitor.

Figure 3 Installation order

The monitor terminals and their destination are given below :

Terminal

LN +

LN -

GND

VI1

+E

DATA

Ec1

Ec2

GND

VI2

Destination

Intercom line between monitor and commutator /doorstation

Ground

VIDEO IN from doorstation built-in camera

Supply voltage for monitor

DATA exchange between monitor and commutator BKM-440

Supply voltage for doorstation built-in camera

Supply voltage for

extra

camera

Ground

VIDEO IN from

extra

camera

See Fig. 4 - 7 for the examples of wiring diagrams of the monitor and other doorphone units.

Acceptable cross-sections of wires to connect the monitor to the power supply unit, doorstation / control unit (Fig. 4 - 5) are given in the doorstation / control unit operating instructions.

Acceptable cross-sections of wires to connect the monitor to the commutator BKM-440 (Fig. 6 - 7) are given in the commutator BKM-440 operating instruction.

Note.

If the monitor operates together with the commutator BKM-440, a door bell button connection is not available .

EXAMPLES OF WIRING DIAGRAMS

DC IN

MONITOR

- 440 C

GND

VI2

GND

Ec2

Ec1

DATA

+E

VI1

GND

LN-

LN+

+E

To next commutators

VO

GND

Ec

Door bell button

Extra Camera

12 V , 0.3 А max

Power Supply SA03010029

18В, 0.5А

To other apartments

82-Ohm resistor should be connected between the VO and VG terminals of the last commutator in the circuit

SEL

Ek

GND

LINE

-18

+18

Commutator

BK-4MV

( or BK-4V )

VI

VG

VG

VO

To doorstation / control unit

Note. Door bell button can be installed near your apartment door, and connected to the GND and DATA terminals of the monitor

Figure 4 Monitor VIZIT-M440C with multi-apartment doorstation and extra camera

MONITOR

VIZIT M C

VI2

GND

Ec2

Ec1

DATA

+E

VI1

GND

LN-

LN+

POWER SUPPLY

BPD18/12-1-1 +18

-18

-12

+12

VO

GND

Ec

Door bell button

50 V

1A

Extra Camera

12 V , 0.3 А max

Colour

LC

Ec

VO

+E

GND

LINE

INDIVIDUAL / STOREY

DOORSTATION

ELECTROMECHANICAL

VIZIT-M440C with individual / storey doorstation and extra camera

MONITOR

- 440 C

VI2

GND

Ec2

Ec1

DATA

+E

VI1

GND

LN-

LN+

VO

GND

Ec

Extra Camera

12 V , 0.3 А max

·

·

·

Main Monitor

Individual / storey doorstation activation

Switching of video channels

Intercom priority over Extra Handset

C

COMMUTATOR

BKM-440

A B

HS/MON

EQUIV

Extra Handset

-

+

INDIVIDUAL / STOREY

DOORSTATION

VO

VG

LN

GND

+E

Ec

LC

To next commutators

To other apartments

SEL

Ek

GND

LINE

-18

+18

COMMUTATOR

BK-4MV

( or BK-4V )

VI

VG

VG

VO

+12

-12

-18

+18

POWER SUPPLY

BPD18/12-1-1

82-Ohm resistor should be connected between the VO and VG terminals of the last commutator in the circuit 50 V

1A

ELECTROMECHANICAL

To multi-apartment doorstation / control unit

Figure 6 Monitor VIZIT-M440C ( ) multi-apartment doorstation, individual / storey doorstation and extra camera

MONITOR

TERMINAL

460 CM

DATA

+E

VI

GND

LN-

LN+

AWA

Y

REC

MENU

Main Monitor

·

·

·

Individual / storey doorstation activation

Switching of video channels

Intercom priority over Extra

Monitor

LN+

LN-

GND

VI1

+E

DATA

Ec1

Ec2

GND

VI2

MONITOR

- 440 C

C

COMMUTATOR

BKM-440

A B

HS/MON

EQUIV

Extra Monitor

·

Individual / storey doorstation activation - N/A

·

Switching of video channels - N/A

INDIVIDUAL / STOREY

DOORSTATION

VO

VG

LN

GND

+E

Ec

LC

INDIVIDUAL / STOREY

DOORSTATION

BVD-401СВ

LN

GND

+E

VO

Ec

LС

50 V

1A

50 V

1A

+12

-12

-18

+18

POWER SUPPLY

BPD18/12-1-1

ELECTROMECHANICAL ELECTROMECHANICAL

+12

-12

-18

+18

POWER SUPPLY

BPD18/12-1-1

Figure 7 Monitor VIZIT-M440C ( as extra device ) with two individual / storey doorstations

SETUP

Before turning the power on, make sure that there is no misconnection or risk of short circuit.

§ Turn on the power supply unit or commutator BKM-440.

The monitor Power LED (see Fig.1) illuminates with green light. If the Power LED is dim, the monitor is in the sleep mode (calls are ignored, and all buttons except for are disabled).

To switch the monitor on, press the button.

§ Select a ring tone, set its volume, adjust brightness and saturation of colour image from doorstation camera .

Press . Image from the doorstation camera appears on the screen. Press one of the preset buttons: to set the ring tone volume; to select new ring tone; to adjust image brightness; to adjust image saturation.

When you press the button, its LED indicator illuminates to show which setting is now active.

Setting the ring tone volume (3 levels).

Press . LED indicator illuminates. Press to decrease or to increase volume. Every time you press either or

, the test sound rings to present the volume level, and the LED is blinking. When the lowest or the highest level is reached, LED blinking stops.

Selecting a new ring tone (one of five).

Press . LED indicator illuminates. Press or to select a new ring tone. Every time you press either or , the selected ring tone sounds.

Adjusting image brightness

Press . LED indicator illuminates. Press or . The LED is blinking. When the lowest or the highest degree of brightness is reached, the LED blinking stops.

Adjusting colour image saturation

Press . LED indicator illuminates. Press or . The LED is blinking. When the lowest or the highest degree of saturation is reached, the LED blinking stops.

Quitting Setup Mode

1.

To quit the setup mode immediately, pick up the handset and hang it up again. The screen shuts off.

2.

The monitor quits the setup mode automatically in 15 seconds of idle, if you do not press , , , , or for 15 seconds.

buttons

§

If an extra camera and ordinary door bell button are connected to your monitor (see Fig. 4, 5), you can set an ring tone for calls from the door bell button, and individual image brightness and saturation for the extra outdoor camera .

Note, that the ring tone volume remains the same for both the doorstation and door bell button.

Press , then . Image from the extra camera appears on the screen.

Select a ring tone, set image brightness and saturation, as described above.

§ an

If two doorstations are connected to your monitor via BKM-440, and used as the individual ring tone, image brightness and saturation for calls from both main device (see Fig. 6), you can set doorstations . The ring tone volume remains the same for both doorstations.

Press the button, image from the first (i.e. main entrance) doorstation appears in the monitor. Perform the settings as described above.

Press the button once more, image from the second (individual/storey) doorstation appears on the screen. Perform the settings as described above.

Note

§ If your monitor is connected to settings for doorstations are two doorstations not available, via BKM-440, and used as an they remain the same for both extra doorstations.

device (see Fig. 7), individual

To adjust current settings of the monitor as extra device, make a call from one of the connected doorstations. Image arrears on the screen. Select a ring tone, set its volume, set image brightness and saturation, as described above.

FUNCTIONAL CHECK AND OPERATION ORDER

When a call is made from the doorstation, the monitor rings. Image from the doorstation camera appears on the screen.

Pick up the handset and check duplex intercom. During intercom, press to view image from the extra camera (see Fig. 4,

5, 6), if needed. Press again to switch back to the image from the doorstation camera.

To release the door lock, press and hold until the beep. The door is unlocked now. After you release the intercom is still available. Hang up the handset. The screen shuts off, the monitor goes to the Stand-By mode.

Note.

You can unlock the door without picking up the handset. When called, just press and hold door is unlocked now . After you release , the monitor goes to the Stand-By mode.

button, until the beep. The

To activate the individual / storey doorstation (i.e. start intercom and video monitoring on your initiative, see Fig. 5), pick up the handset. Image appears on the screen, intercom is available. You can press to view image from the extra camera, if needed. Press again to switch back to the image from the doorstation camera.

At pressing the door bell button, the monitor rings, image from the extra camera appears on the screen (see Fig. 4, 5).

To engage the sleep mode, press and hold until the Power LED turns off.

Special notes on operation with BKM-440

The monitor can be connected to the BKM-440 either as the main monitor has an intercom priority over any extra main (see Fig. 6) or the device, i.e. when you pick up the extra monitor (see Fig. 7). The main monitor’s handset, the extra monitor (or extra apartment handset) is disengaged. The doorstation.

extra monitor cannot activate the individual / storey

To view the door zone in front of main entrance doorstation (see Fig. 6), press on the handset. To switch to viewing the door zone in front of individual / storey doorstation, press with the individual / storey doorstation, pick up the handset.

main monitor, or pick up its again. To start intercom

Screen

Colour system

Video IN

-

impedance voltage

Operating voltage

Power consumption

Dimensions (W)x(H)x(D)

Weight

:

Ambient temperature range

Relative humidity of air

SPECIFICATIONS

3.5” (89mm)

PAL

TFT LCD

470 Ohm

1…1.8

V p-p

15…27

3 W

VDC max.

14 0 x 183 x 48

0.6 kg mm

OPERATING CONDITIONS

+ 5°C up to to +

93%

40°C at + 25°C