Sole SLTV15MS3 Instructions For Use Manual

Safety Instructions

EN 2

15 TFT-LCD TV

FCC Information

This equipment has been tested and found to comply with limits for a class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment can generates, uses, and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inteference to radio Communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause unacceptable interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced Radio/ TV technician for help.

Caution

Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Ver 2.00NSO

Notes & Descriptions

To reduce the risk of fire, electrical shock and other injuries, keep these safety precautions in mind when installing, using and maintaining your TV.

Warning : If you manipulate against the notice, it may cause serious injury or death to user.

Caution : If you manipulate against the notice, it may cause slight injury to user or appliance.

Please recycle to preserve environment.

PAL/SECAM

3

Warning

Disconnect the power cable and signal cable connected to the product in case of thunder or lightning.

Do not attempt to touch its power cord with wet hands.

If any electric pin is wet or dusty, remove the moisture or dust first before use.

It is recommended to pull out the power cord unless you use it for a long time.

Damaged power cord, plug or unfitted outlet may be very dangerous.

Do not install the set close to any heating sources.

Do not place heavy articles on it or step on the product.

The product should be installed on a clean and dry place.

When you detect any smog, unusual noise or smell, just disconnect the electric power and refer servicing to qualified service personnel.

Do not place any bowl with water, beverage, can or other liquid products on it.

Do not use or place any combustible sprayer or inflammable substances close to the product.

Do not arrange the power cord close to any heating devices/sources.

Install the outdoor antenna for the set far away from high voltage cables.

EN 4

15 TFT-LCD TV

When moving it, do not apply any forces on the set.

Do not attempt to disassemble, repair or change the product.

Whenever you need to repair, adjust or check it, refer servicing to qualified service personnel.

Do not directly spray water or rub it with inflammable substances (thinner or benzene) when cleaning it.

Do not wet or penetrate water over/into the set.

When cleaning the LCD surface, disconnect the power and use a piece of smooth cloth against any scratches on it. Never use wet cloth.

Caution

Make sure to pull out the power cord when cleaning or removing the product.

Ventilation should be always open and the set should be installed in a wellventilated and wide enough place (a minimum distance away from a wall 10cm or more).

Do not install the set in a place directly exposed to sunlight.

PAL/SECAM

5

Available Temperature & Humidity

Operating Temperature

Storage Temperature

Operating Humidity

Storage Humidity

0~40˚C

-10~50˚C

10~60% RH

10~90% RH

For non-active pixel of LCD :

There may be red spots, green spots, blue spots and black spots on the screen. This is a characteristic of liquid crystal panels and is not a problem. The liquid crystal panel is built with very high precision technology giving you fine picture details. Occasionally, a few non-active pixel may appear on the screen as a fixed point of red, green, blue or black. Please note this does not affect the performance of your LCD.

When used as a PC monitor :

Optimal Resolution: 1024 768 @ 60Hz.

NOTE :

If the same pattern is continuously displayed on the TV/Monitor for a long period of time, it will result in image "sticking" to the screen. The marking or retained image on the LCD panel results from fixed image use is not an operating defect. As such is not covered by warranty. This product is not designed to display fixed image patterns for extended period of time.

EN 6

15 TFT-LCD TV PAL/SECAM

7

Contents

CHAPTER 1.

Before Use

1-1. Accessories

1-2. Panels

1-3. Remote Control

1-4. Menu Configuration

1-5. Jog Shuttle Button

1-6. Inserting the Batteries in the Remote Control

12

13

16

18

20

21

CHAPTER 2.

Connection

2-1. Connecting Power

2-2. Connecting TV Antenna

2-3. Connecting PC

2-4. Connecting HDTV

2-5. Connecting DVD

2-6. Connecting VIDEO / S-VIDEO

2-7. Connecting Headphone (Speaker)

CHAPTER 3.

Using TV Menus

3-1. Watching TV

3-2. Channel Search

3-3. Fine Tune

3-4. Add/Remove Channel

3-5. Channel Swap

3-6. Change TV Channel Mode

3-7. Closed Caption

3-8. V-chip Function

EN 8

15 TFT-LCD TV

26

26

27

24

24

25

25

36

37

38

39

30

33

34

35

CHAPTER 4.

Using Menus of Picture,

Sound and Others

4-1. Setting Picture Mode

4-2. Setting Sound Mode

4-3. Setting Option

CHAPTER 5.

Using PC MENU

5-1. Auto Adjustment

5-2. Setting Picture

5-3. Setting Sound

5-4. Setting Option

5-5. Setting Color Temperature

CHAPTER 6.

Specifications

6-1. Dimensions

6-2. Specifications

CHAPTER 7.

Services & Others

7-1. Troubleshooting

7-2. Concerning Services

48

49

50

51

52

42

44

45

54

55

58

60

PAL/SECAM

9

EN 10

15 TFT-LCD TV

CHAPTER 1

Before use

1-1. Accessories

1-2. Panels

1-3. Remote Control

1-4. Menu Configuration

1-5. Jog Shuttle Button

1-6. Inserting the Batteries in the Remote Control

PAL/SECAM

11

1-1. Accessories

Please make sure the following items are included with your LCD TV.

If any items are missing, contact your dealer.

AAA-type battery( 2) RF Cable

Power Cord DC Adaptor

Remote Control

User’s Manual

EN 12

15 TFT-LCD TV

1-2. Panels

1) Front Panels

-

-

-

-

-

Power/Menu

Channel Button

Sound Cont.

Remote Control Sensor

LED

Power-On/Off

AUTO / Move above Menu

SOURCE / Move under Menu

Exit Menu

Load Menu

Auto button operates as auto adjustment function when it’s input singnal is PC.

Power button is jog shuttle type button and it operates different functions by pushing it to Up/Down/Left/Right.

PAL/SECAM

13

2) Rear Panels

EN 14

15 TFT-LCD TV

Power Input

PC Input

Audio (PC Input/Headphone Output)

TV Antenna Input

3) Side Panels

Audio Input (L, R)

S-Video Input

Video Input

PAL/SECAM

15

1-3. Remote Control

Power On/Off

Sound off Temporarily

Channel Selection Button

TV & Input Source Selection Button

Not available

Control Picture Mode

Channel & Volume Control Button

Menu Control Button

Not available

TV Functions & Teletext Menu Button

Not available

Not available

Functions by remote control buttons

Button

POWER

0~9

Function

Power On/Off

Numeric Buttons.

Button

MUTE

- / --(+100)

Function

Sound off Temporarily

Select channels over 100

CH UP/DOWN Move TV Channels PRE

VOL +/-

SOURCE( / ) Input Source selection Botton (PC S-Video Video Full SCART TV Half SCART)

PC PC Input TV TV Input

PM

MENU

Previous Channel

Control Volume

Control Picture Mode SM

Displays the MENU On Screen

Not available

DUAL I/II (MTS) Not available

ON SCREEN Display screen status

SCALE

/ /

Control Picture Scale EXIT Exit Main / Sub MENU

MENU settings (Move MENU up and down / Move MENU left and right / MENU Confirmation)

TELETEXT

MEM

SLEEP

HISTORY

SUBTI

MENU

TV/RADIO

Not available

Add / Remove a TV CH

Sleep Timer setting

Not available

Not available

Not available

Not available

SCREEN

LIST

DTV

EPG

PIP

Not available

Not available

Not available

Not available

Not available

The remote control provided operates up to 7m from the optical receive part within Left/Right

30 degrees.

EN 16


17

1-4. MENU Configuration

Most functions of the TV set can be controlled by MENU and selection buttons on the remote control, so learning how to operate them would be convenient for you.

1) Menu Configuration

Main Menu

Sub Menu Settings

2) Using Remote Control

Press

MENU button to display main menu.

Press Menu control button ( / ) to move to sub menu of a selected main menu.

To move among menus, use Menu control button ( / ).

To change a selected menu setting, use Menu control button ( / ).

Press EXIT button to return from sub menu to main menu or from main menu to menu removal.

EN 18


19

1-5. JOG Shuttle Button

Push

MENU button right to display main menu.

Push it right again to display sub menu.

Push

MENU button left to return to main menu.

Push it left again to clear menu.

Push the button up and down to move among menus.

If pushing it downward when menu is not display, it changes input signals.

1-6. Inserting the Batteries in the

Remote Control

Remove the cover of the remote control.

Check the polarity of batteries and insert them in right directions.

Replace the cover.

Available batteries : 2 DC 1.5V AAA-type batteries

Since incorrect insertion of batteries may cause breakage, leakage or injuries, check the polarities before the insertion.

Separate and collect used batteries for the protection of environment.

Do not use alkaline and manganese batteries together.

EN 20


21

EN 22

15 TFT-LCD TV

CHAPTER 2

Connection

2-1. Connecting Power

2-2. Connecting TV Antenna

2-3. Connecting PC

2-4. Connecting HDTV

2-5. Connecting DVD

2-6. Connecting VIDEO / S-VIDEO

2-7. Connecting Headphone (Speaker)

PAL/SECAM

23

2-1. Connecting Power

The product automatically adjusts voltage.

Power Cable should be firmly connected to an outlet or DC adaptor in order not to be pulled out or shake.

2-2. Connecting TV Antenna

When round cable (75

Ω coaxial cable) is used, copper part of the cable should not be bent.

Connecting RF cable

TV antenna

Connecting feeder cable

Antenna converter

RF cable

TV Wall-outlet feeder cable copper wire

TV Wall-outlet

Cautions

1. When an outdoor antenna is used, it is recommended for a qualified technician to install it.

2. For weak radio wave, signal amplifier (purchased separately) is recommended for use.

EN 24

15 TFT-LCD TV

2-3. Connecting PC

<Input>

<Output>

Connect D-Sub Cable to D-Sub port on the TV and PC.

Connect Audio Cable (not included) to Audio output of a PC (stereo jack) and PC

Audio Input Port of the TV (stereo jack).

2-4. Connecting HDTV

Digital TV Broadcasting Receiver

Pb Y Pr L R Pb Y Pr L R

<Output>

<Input>

Connect Component Cable (not included) to HDTV Connection ports of TV (Pb Y

Pr) and DTV Receiver.

Connect Audio Cable (not included) to Audio ports (L/R) of TV and DTV Receiver.

Cables should be connected to ports of the same colors.

PAL/SECAM

25

2-5. Connecting DVD

DVD Playera

R

L

Pr

Y

Pb

<Input>

Pb Y Pr L R

<Output>

Connect Component Cable (not included) to Component ports of TV and DVD player. VCR, Set-Top box or camcorder.

2-6. Connecting VIDEO/S-VIDEO Input

Video & DVD Player

L R

Audio Video S-VIDEO

<Input>

<Output>

Connect Video/Audio Cable (not included) and S-VIDEO Cable to Video port of TV and camcorder, game machines, VCR, DVD player or Set-Top box.

EN 26

15 TFT-LCD TV

Cables should be connected to ports of the same colors.

Audio signals of S-VIDEO should be used with external audio signal cables.

S-VIDEO signal secures better picture quality than composite video signal.

2-7. Connecting Headphone(speaker)

<Output>

Connect Headphone (not included) to the Headphone output port of the TV.

If possible, use headphones of 8ohms impedance. Otherwise output volume may be too low or too loud.

In case of connecting to speakers, connect speakers with amps. If connected with speakers without amps, the output volume may be low.

PAL/SECAM

27

EN 28

15 TFT-LCD TV

CHAPTER 3

Using TV Menus

3-1. Watching TV

3-2. Channel Search

3-3. Fine Tune

3-4. Add/Remove Channel

3-5. Channel Swap

3-6. Change TV Channel Mode

3-7. Closed Caption

3-8. V-chip Function

PAL/SECAM

29

3-1. Watching TV

1) Precautions in the initial installation

Check whether TV antenna cable is properly connected.

Check input voltage then connect power cord and adaptor to TV.

TV is now ready to be turned on.

2) Turning on TV

Press the Power button on either the TV set or the remote control.

Each pressing the button turns on or off the set.

Power Button on Remote Control Power Button on the TV Set

EN 30

15 TFT-LCD TV

3) Channel Selection

Press

CH button on the remote control to change channels.

Press numeric buttons (0~9) to go to a channel directly.

Press buttons ) on the TV set to change TV channel up or down.

Channel button on the remote control Channel button on the TV set

4) Move to Previous Channel

When pressing the

PRE button on the remote control, it moves back to a previous channel.

Previous Channel Button

5) Volume Control

Increase/decrease volume by pressing

VOL

Press

VOL button on the remote control.

button ( + / - ) on the TV set to control the volume.

Volume Button on the remote control Volume Button on the TV Set

PAL/SECAM

31

6) Mute

MUTE button on the remote control

Press

MUTE button on the remote control to turn off the sound.

Press it again to turn the sound back on or press volume buttons.

7) Checking the present broadcasting information

Broadcasting Info Button

Press

ON SCREEN button on the remote control to display the information on the screen.

Press it again to remove the information except input source automatically.

Press it again to remove all information.

3-2. Channel Search

When using the TV for the first time, or after reconnecting it due to power failure or other reasons, channels should be searched and registered again.

- Press

MENU button on the remote control.

- Once you move to Start by using button on the remote control, it starts channel search.

- To stop channel search, repress


- If you stop it during channel search, it stores the currently searched channels only.

- Also, it can be set in OSD by using JOG button.

EN 32


33

3-3. Fine Tune

If a searched channel is unclear or the sound is not working properly, use Fine Tune function to adjust.

- Press

MENU button and move to <CH Fine Tune> menu.

- Set the best status with button on the remote control.

- To stop channel search, repress


- Once the setting is complete, exit from menu.

3-4. Add/Remove Channel

You may add or remove a channel as your need.

- Channel can be added or removed by pressing numeric buttons(0~9) or

CH

- Press

MEM button on the remote control.

- In case of adding a channel by using button.

button on the remote control, move to Add.

- Once the setting is complete, press

MEM button again.

- Also, it can be set in OSD menu by using JOG button.

EN 34


35

3-5. Channel Swap

For frequently watched channels, you can store and swap between those channels.

- Move to a channel to change.

- Press

MENU button on the remote control and move to <CH Swap> menu.

- Set both channels that you are watching and want to swap.

- Change the default and escape the menu.

3-6. Change TV Channel Mode

Please choose your TV input type by selecting either Air or Cable.

If set as Air, some cable broadcast stations will not be displayed.

- Press

MENU button on the remote control and move to <CH Mode> menu.

- Set the CH Mode between Air & Cable by using button on the remote control.

- Once the setting is complete, press

MENU button.


EN 36


37

3-7. Closed Caption

This function works only with caption broadcast or other CC marked video tape and

DVD title.

Set the function in the SETUP menu.

Caption can be set only by using the remote control.

- Select a TV station, video tape or DVD title

- Press

MENU

Caption> menu.

button on the remote control and move to <Closed

- Set Caption broadcast type by using button on the remote control.


3-8. V-Chip Function

This function deals with MPAA rating of TV broadcast and other media.

It works only with V-Chip function broadcast and media.

- Press

MENU button on the remote control and move to <V-Chip> menu.

- Set the V-Chip menu by using button on the remote control.

Default V-Chip PIN is 0000.

Please change PIN as yours when you install.

- Press button and enter Password.

- Press pin number using the remote control.

- A number can be deleted with left volume button when using it.

- Set V-Chip function by using button on the remote control.

EN 38


39

- Move to TV Guideline or MPAA Rating by using button on the remote control.

- Move to the position which you want to make channel blocking and press

MENU button for setting.

- Press it again for cancellation.

- Escape the menu pressing EXIT.

- V-chip function can be set up only by the remote control.

EN 40

15 TFT-LCD TV

CHAPTER 4

Using Menus of

Picture, Sound and Others

4-1. Setting Picture Mode

4-2. Setting Sound Mode

4-3. Setting Option

PAL/SECAM

41

4-1. Setting Picture Mode

1) Image Scale : Full - Wide

You can set the screen’s suitable image scale of TV or Video input signals and view them accordingly.

- Press

SCALE button on the remote control.

Full : Show a screen in the full LCD Panel.

Wide : Show a screen in the 16:9 Wide screen size.


2) Mode : Standard - Soft - Dynamic - User

- Press PM button on the remote control.

- Set a picture mode by using PM button on the remote control.

Standard : Standard picture mode.

Soft : It displays a picture softly as a whole and is better for watching movie or regular cable TV.

Dynamic : This mode is suitable for watching sports or movie.

User : It is a picture mode customized by a user.


EN 42


43

3) Brightness : Adjust screen brightness

4) Contrast : Adjust screen contrast

5) Color : Adjust screen color

6) Tint : Adjust screen tint

7) Sharpness : Adjust screen sharpness

4-2. Setting Sound Mode

Volume : Adjust volume

Bass : Adjust bass

Treble : Adjust treble

Balance : Adjust balance of left & right speaker

EN 44

15 TFT-LCD TV

4-3. Setting Option

- Press

MENU button on the remote control to move to Main Menu.

- Change the settings by using / button on the remote control.

Sleep Timer

- Press

SLEEP button on the remote control.

- Sleep timer can be set up to 180 minutes.

Menu Timeout : It can be adjusted to display OSD Menu between 5 ~ 60 seconds.

Menu Language : Change a language to display OSD.

Factory Reset : Reset all the OSD control settings back to the factory default setting.

Version : It shows the product version.

PAL/SECAM

45

EN 46

15 TFT-LCD TV

CHAPTER 5

Using PC MENU

5-1. Auto Adjustment

5-2. Setting Picture

5-3. Setting Sound

5-4. Setting Option

5-5. Setting Color Temperature

PAL/SECAM

47

5-1. Auto Adjustment

When the set is connected to a PC, the MODE should be set as PC RGB Mode.

- Press

AUTO with the PC.

button on the remote control synchronize the TV set

- When it is used as PC monitor

Optimal Resolution : 1024 x 768 @ 60Hz

- Picture may not be displayed properly in any resolution other than the optimal resolution.

- Even though it is automatically adjusted, it may display picture depending on signals from a PC and in this case, It is then recomended to use Auto Adjustment function.


The Standard Signal Modes for PC Monitor

Resolution

(H V)

640 480

640 480

640 480

720 400

800 600

800 600

800 600

800 600

1024 768(Optimal)

1024 768

1024 768

Vertical Frequency Horizontal Frequency Clock Frequency

(kHz) (Hz) (MHz)

31.469

37.861

59.94

72.809

25.175

31.5

37.5

31.469

35.156

37.879

75

70.087

56.250

60.317

31.5

28.322

36

40

48.077

46.875

48.363

56.476

60.023

72.188

75

60.069

70.069

75.029

50

49.5

65

75

78.75

Polarity

(Vert./Hor.)

-/-

-/-

-/-

-/+

+/+

+/+

+/+

+/+

-/-

-/-

+/+

When you use it as a PC monitor, depending on signals of a PC, it may not display picture normally even though it is set for standard mode resolution.

5-2. Setting Picture

- Brightness : Adjust screen brightness

- Contrast : Adjust screen contrast

- Phase : In case picture is not optimally set after auto-adjustment, use Phase function.

- H. Size : Adjust the Size of the screen.

- H. Position : Adjust the H position of the screen.

- V. Position : Adjust the V position of the screen.

- Auto Adjustment : Automatically resets its all settings to optimize the picture quality.

EN 48


49

5-3. Setting Sound

- Volume : Adjust volume

- Bass : Adjust bass

- Treble : Adjust treble

- Balance : Adjust balance of left & right speaker

5-4. Setting Option

.

- Press

MENU

Menu.

button on the remote control to move to Main

- Change the settings by using / button on the remote control.

Sleep Timer

- Press

SLEEP button on the remote control.

- Sleep timer can be set up to 180 minutes.

Menu Timeout : It can be adjusted to display OSD Menu between 5 ~ 60 seconds.

Menu Language : Change a language to display OSD.

Factory Reset : Reset all the OSD control settings back to the factory setting status.

Version : It shows the product version.

EN 50


51

5-5. Setting Color Temperature

- Press

MENU button on the remote control and move to <Color Temp> menu .

- Set the value between 5500, 7300, 9300 or you can set as your preference in USER.

CHAPTER 6

Specifications

6-1. Dimensions

6-2. Specifications

EN 52


53

6-1.Dimentions

17.5mm

35.6mm

323mm

356mm

Weight : approx. 4.5kg (before packing) / approx. 5.9kg (after packing)

323mm

EN 54

15 TFT-LCD TV

6-2. Specifications

Dimensions, design and all specifications are subject to change without any prior notice.

Product Name

LCD Panel

15” TFT-LCD TV

Type

Size

Pixel Pitch

Contrast Ratio

Brightness

Actual Display Size

Viewing Angle

Interface

TV Broadcasting System

Audio Output

PC Monitor Horizontal Frequency

Vertical Frequency

Power

Colors

Max. Resolution

Adaptor Input

Adaptor Output

Power Consumption

Energy Saving Mode

Amorphos Silicon TFT-LCD

15” (diagonal length)

0.297 mm x 0.297 mm

500 : 1 (Typ.)

450 cd /

304.1mm (H) x 228.1mm (V)

L/R : 130° U/D : 100°

LVDS

NTSC-M Type

MAX 3W x 2 / Stereo

30 ~ 61 KHz

60~ 75 Hz

16M colors

XGA : 1024 (H) x 768 (V)

AC 100V~240V, 50~60Hz

DC 12 V

In-Operation < 40W

Power-Saving Mode/OFF < 5W

VESA DPMS

PAL/SECAM

55

EN 56

15 TFT-LCD TV

CHAPTER 7

Service & Others

7-1. Troubleshooting

7-2. Concerning Services

PAL/SECAM

57

7-1. Troubleshooting

If the TV seems to have a problem, please check the followings first.

If you still have the same symptoms even after taking the following actions, contactyour local dealer or nearest service centre.

1) TV-related Troubles

Unclear display or noisy sound

Check whether TV antenna is correctly connected.

Broadcasting may not be good in an area with bad reception or far away from a station/network.

No image

Check whether power is connected correctly. And press the

POWER button.

Black background only

Check whether the mode is set as PC monitor or Video/S-Video Input, not TV mode.

Strips and shaking display

It may be interrupted by neighboring radio waves (please check any wireless phone, hair drier, electric drilling machine and etc)

Execute fine tuning for manual adjustment.

Can’t receive a specific channel

Check whether Channel Setting is normally set.

Try to rotate an antenna’s direction.

Picture plays without sound

Try to press

MUTE button.

Volume up by using

VOL button.

EN 58

15 TFT-LCD TV

2) PC Monitor-related Troubles

No image on the monitor

Check whether the D-Sub cable is firmly connected to the TV and a PC.

Check whether a graphic card is correctly inserted into the slot.

Check whether the Power of a PC and the TV is on.

Checck whether a graphic card or mode is set appropriately on a PC.

Referring to the Standard Signal Mode for PC Monitor in the previous chapter, change graphic mode.

Check whether D-Sub cable pins are not inserted or bent.

No Power

Check whether the power cord is normally inserted and reconnect it.

Pull out the power cord from wall outlet and reconnect it in 10~20 minutes.

LED Lamp turns off in red and it shows no image

Check whether the graphic cable is connected to theTV and a PC.

Check whether a computer is in power-saving mode and attempt to operate keyboard and mouse.

Unstable or unfocused image or trembling

Check whether the D-Sub cable is connected to the TV and a PC.

If a PC’s display mode is changed, the screen needs readjusting, so you need to use Auto Adjustment or Picture Adjustment.

Check whether the TV and your graphic card are compatible each other and whether it is set as an appropriate refresh rate. If letters look distorted, change the refresh rate to 60Hz.

Abnormal image scale

By using vertical/horizontal position in Picture Adjustment Menus, adjust the position.

Try to execute Auto Adjustment function.

PAL/SECAM

59

7-2. Concerning Services

In one of the following cases, warranty will be void.

1) Malfunctions resulting from inserting of foreign substances (water, beverage, coffee and etc)

2) Dropping or applying force causing damages to the product or induce malfunction.

3) Appearance damage or transformation by use of organic solutions such as thinner, benzene and etc.

4) Malfunction due to disassemble by the user.

5) When other parts/consumption accessories (including adaptor) that are not supplied by the manufacturer causing malfunction.

6) Supplying wrong voltage to the unit causing malfunction.

7) A repair or modification performed by an unauthorized service personnel causing malfunction.

8) Natural disasters (lightning, fire, flood, gas, damage from sea wind, earthquake and etc) directly cause troubles

9) Violation against the directions in the manual causing malfunction.

10) Customer’s mishandling causing malfunction.

EN 60

15 TFT-LCD TV

No results