advertisement
JVC
COMPACT COMPONENT SYSTEM
SISTEMAS DE COMPONENTES COMPACTOS
SISTEMA DE COMPONENTE COMPACTO
CA-HXZ3
,JVC
QOQ_
QQQ_
Q© m
I
I
I
I
DIGITAL AUDIO
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
INSTRU(_6ES
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear, bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
GVT0086-012A
[UW, U J]
Warnings,Cautionsand Others
Avisos,precaucionesy otras notas
Advert_ncias,precau_Oese outrasnotas
Caution-0/I (standby/on)
button!
Disconnect the mains plug to shut the power off completely. The 0/I (standby/on) button in any position does not disconnect the mains line. The power can be remote controlled.
Precaucibn--lnterruptor
O/I (encendido/apagado)!
Desconectar el cable de alimentaci6n para desactivar la
alimentaci6n totalmente. Cualquier que sea la posici6n de
ajuste del interruptor O/I (encendido/apagado), la
alimentaci6n no es cortada completamente. La
alimentaci6n puede ser controlada remotamente.
Precaug_o--lnterruptor
0/I (esperar/ligar)!
Desconectar o cabo de alimenta_&o para desligar a alimenta_&o por completo. Qualquer que seja a posi_&o de ajuste do interruptor 0/I (esperar/ligar), a alimenta_&o n&o e completamente cortada. A alimenta_&o pode ser controlada remotamente.
-G-1 -
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2.
Do not expose this appliance to rain or moisture.
•
•
•
•
CAUTION
Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)
Do not place any naked flame sources, such as lighted candles, on the apparatus.
When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.
Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
PRECAUClON
Para reducir riesgos de choques electricos, incendio, etc.:
1. No extraiga los tornillos, los cubiertas ni la caja.
2.
No exponga este aparato a la Iluvia o a la humedad.
PRECAUCION
• No obstruya las rendijas o los orificios de ventilaci6n.
(Si las rendijas o los orificios de ventilaci6n quedan tapados con un peri6dico, un trozo de tela, etc., no se podrA disipar el calor).
• No ponga sobre el aparato ninguna llama al descubierto, como velas encendidas.
• Cuando tenga que descartar las pilas, tenga en cuenta los problemas ambientales y observe estrictamente los reglamentos o las leyes locales sobre disposici6n de las pilas.
• No exponga este aparato a la Iluvia, humedad, goteos o salpicaduras.
Tampoco ponga recipientes conteniendo liquidos, como floreros, encima del aparato.
PRECAUQ._O
Para reduzir riscos de choques eletricos, inc6ndio, etc.:
1. NAo remova parafusos e tampas ou desmonte a caixa.
2.
NAo exponha este aparelho & chuva nem
& umidade.
AVISO
• N&o obstrua as aberturas e oriffcios de ventila£&o. (Se os oriffcios ou aberturas de ventila£&o estiverem obstrufdos por qualquer papel ou tecido, nAo haverA circula£&o do ar quente.)
• N&o coloque nenhum objeto com chamas, como velas acesas, sobre o aparelho.
• Ao descartar as baterias, leve em considera£&o os problemas que possam ser causados ao meio ambiente e os regulamentos e leis locals e governamentais sobre recolhimento dessas baterias devem ser rigorosamente seguidos.
• N_o exponha este aparelho & chuva, umidade, pingos ou esguichos de Agua, nem coloque em cima do mesmo qualquer tipo de recipiente que contenha Ifquidos, como por exemplo vasos.
-G-2-
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1 Front:
2 Sides/Top/Back:
No obstructions
No obstructions and open spacing.
should be placed in the areas shown by the dimensions below.
3 Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.
Precauci6n: El aparato debe estar bien ventilado
Para evitar posibles riesgos de descargas electricas e incendios y prevenir cualquier posible da_o, coloque el aparato del modo siguiente:
1 Parte delantera: No ponga nada delante, deje el espacio libre.
2 Laterales/parte superior/parte trasera:
3 Parte inferior:
No se deberia colocar nada en las Areas y las distancias que se detallan a continuaci6n.
Coloque el aparato sobre una superficie recta. Debe haber buena circulaci6n de aire; para ello, coloque el aparato sobre una base a una altura minima de 10 cm.
Precau_o:
Ventila_o
adequada
Para evitar riscos de choques eletricos e inc_ndios, e prevenir avarias, instale o aparelho como segue:
1 Parte frontal: Sem obstru_Ses e espa_os abertos.
2 Partes laterais/ Tampa/ Posterior:
Nenhuma obstru_&o devera ser colocada entre as areas cujas dimensSes s&o indicadas abaixo.
3 Parte inferior: Instale-o sobre uma superficie plana. Devera ser mantido espa_o suficiente para a ventila_&o se este for instalado numa posi_&o que tenha uma altura de 10 cm ou mais.
Front view
Vista frontal
Vista frontal
15 cm
]15cm
1 15 cm
Side view
Vista lateral
Vista lateral
15 cm
115cm
10 cm
- G-3 -
IMPORTANT FOR LASER PRODUCTS
IMPORTANTE PARA PRODUCTOS LASER
IMPOTANTE PARA PRODUTOS LASER
REPRODUCTION OF LABELS / REPRODUCCION DE ETIQUETAS / REPRODU(_.,40 DE ETIQUETAS
(_) CLASSIFICATION LABEL, PLACED ON EXTERIOR
SURFACE
(D ETIQUETA DE CLASIFICACION, PROVISTA
SOBRE LA SUPERFICIE EXTERIOR
(D ETIQUETA DE CLASSIFICA(_,_O LOCALIZADA NA
PARTE POSTERIOR DA CAIXA DO APARELHO
(_ WARNING LABEL, PLACED INSIDE THE UNIT
®
ETIQUETA DE ADVERTENCIA, PEGADA EN EL
INTERIOR DE LA UNIDAD
® ETIQUETA DE ADVERTC:NCIA LOCALIZADA NA
PARTE INTERNA DA UNIDADE
I
CLASS 1
LASER PRODUCT
I
TOBEAM.
(e)
_WRSEL: ..L_ligla_- telse
(d)
V/WtlH6: 0synligaserstraining pnaq0cnsptirren_r getraktaej
is)
VARO:Avattaessa
suojalukitus olet alttiinan_kym_tt_-
_lle
lasers_teilylle,
1. CLASS 1 LASER PRODUCT
2. DANGER: Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user serviceable parts inside the Unit; leave all servicing to qualified service personnel.
1. PRODUCTO L,&SER CLASE 1
2. PELIGRO: En el interior hay radiaci6n laser invisible. Evite el contacto directo con el haz.
3. PRECAUCION: No abra la tapa superior. En el interior de la unidad no existen piezas reparables por el usuario; deje todo servicio tecnico en manos de personal calificado.
1. PRODUTO LASER CLASSE 1
2. PERIGO: O laser emite uma redia£&o invis{vel que perigosa, caso o apa relho esteja aberto e a trava inoperante ou danificada.
Evite exposi£&o direta ao feixe dos raios.
3. CUIDADO: NAo abra a caixa do aparelho. NAo existem pe£as reparaveis pelo usuario na parte interna da unidade.
Solicite assist_ncia tecnica somente a pessoal tecnico qualificado.
- G-4 -
Introduction
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance from your unit, and retain this manual for future reference.
About This Manual
This manual is organized as follows:
• The manual mainly explains operations
using the buttons and controls on the unit. You can also use the buttons on the remote control if they have the same or similar names (or marks) as those on the unit.
If operation using the remote control is different from that using the unit, it is then explained.
• Basic and common information that is the same for many
functions is grouped in one place, and is not repeated in each procedure. For instance, we do not repeat the
information about turning on/off the unit, setting the
volume, changing the sound effects, and others, which are explained in the section "Common Operations" on pages 9 to 12.
• The following marks are used in this manual:
Gives you warnings and cautions to prevent from damage or risk of fire/electric shock.
Also gives you information which is not good for obtaining the best possible performance from the unit.
know.
Gives you information and hints you had better
Powersources
• When unplugging from the wall outlet, always pull the plug, not the AC power cord.
l i'_ DO NOT handle the AC power cord with wet hands.
I
Moisture condensation
Moisture may condense on the lens inside the unit in the following cases:
• After heating starts in the room
• In a damp room
• If the unit is brought directly from a cold to a warm place
Should this occur, the unit may malfunction. In this case, leave the unit turned on for a few hours until the moisture evaporates, unplug the AC power cord, and then plug it in again.
Internal heat
A cooling fan is mounted on the rear panel to prevent heat buildup inside the unit.
___ For safety, observe the following
carefully: unit. Poor ventilation could overheat and damage the unit.
• DO NOT block the cooling fan and the ventilation
openings or holes. If they are blocked by a
newspaper or cloth, etc., the heat may not be
able to get out.
Precautions
Installation
• Install in a place which is level, dry and neither too hot nor too cold--between 5°C and 35°C.
• Install the unit in a location with adequate ventilation to prevent internal heat buildup in the unit.
• Leave sufficient distance between the unit and the TV.
• Keep the speakers away from the TV to avoid interference with TV.
._
DO NOT install the unit in a location near heat sources, or in a place subject to excessive dust or vibration.
direct sunlight,
Others
• Should any metallic object or liquid fall into the unit, unplug the unit and consult your dealer before operating any further.
• If you are not going to operate the unit for an extended period of time, unplug the AC power cord from the wall outlet.
I_
If anything goes wrong, unplug the AC power cord and consult your dealer.
I
I
I
Contents
Location of the Buttons and Controls
.......................
3
Front Panel .................................................................
Remote Control ..........................................................
3
5
Getting Started
.......................................
6
Supplied Accessories ..................................................
6
Putting the Batteries into the Remote Control ...........
6
Connecting Antennas .................................................
Connecting Speakers ..................................................
6
7
Connecting Other Equipment .....................................
Adjusting the Voltage Selector ...................................
Canceling the Demonstration .....................................
8
8
8
Common
Operations ..................................................
9
Turning On or Off the Power .....................................
9
Turning On or Off the Key-touch Tone ...................... 9
Saving the Power Consumption while on Standby
--Ecology Mode ..................................................
9
Selecting the Sources ...................................................
9
Setting the Clock ......................................................
10
Adjusting the Volume ...............................................
10
Reinforcing the Bass Sound ............................
11
Selecting the Sound Modes ......................................
11
Creating Your Own Sound Mode--User Mode ....... 12
Setting the AM Tuner Interval Spacing .................... 12
Listening to FM and AM Broadcasts
......................
13
Tuning in to a Station ...............................................
13
Presetting Stations ....................................................
13
Tuning in to a Preset Station ....................................
13
Disc Play Introduction
..............................................
MP3 Introduction .....................................................
14
14
Playing
Back
Discs
....................................................
16
Loading
Discs ...........................................................
Playing
Back the Entire Discs--Continuous
16
Play ... 16
Basic Disc Operations ..............................................
Programming the Playing Order of the Tracks
17
--Program Play ..................................................
Playing at Random--Random Play .........................
Repeating Tracks or Discs--Repeat
Prohibiting Disc Ejection--Tray
Play
Lock
................
....................
18
19
20
20
Playing
Back Tapes ...................................................
21
Playing Back a Tape .................................................
21
Locating the Beginning of a Song--Music Scan ..... 21
Recording
..................................................................
22
Recording on a Tape .................................................
22
Synchronized Recording ..........................................
23
• Direct Recording .........................................
23
• Auto Edit Recording (only for audio CDs) ..... 24
Using the Microphones
.............................................
25
Singing along--Karaoke
..........................................
25
• Vocal Masking ................................................
25
• Microphone Mixing ........................................
25
Using the Timers
.......................................................
26
Using Daily Timer ................................................
26
Using Recording Timer ............................................
28
Using Sleep Timer ................................................
Timer Priority ...........................................................
29
29
Maintenance
..............................................................
30
Troubleshooting
........................................................
Specifications
.............................................................
31
32
2
Locationof the Buttonsand Controls
Become familiar with the buttons and controls on your unit.
FrontPanel
FrontPanel
Topview of Indication-lamppanel [!IQ1
SOUND MODE
[]
REC
[]
3
Continued I_L
Display Window
TITLE
GROUP
i i.
TRACK
i i. i i. i i:
@@@NNNN@_N@@@N@@@@
@@@NNNNNN@@@@_@@@@ mmmmmmmmmmmmmmmmmm
@@@m@@@@m@@@@m@@@@ mmmmmmmmmmmmmmmmmm
@@@_@@@@m@@@@m@@@@
@@@@N@@@@@@@@@_@@@
@@@@_@@@@NNNN@_@@@ mmmmmmmmmmmmmmmmmm
@@@@m@@@@m@@@@m@@@ mmmmmmmmmmmmmmmmmm
@@@@_@@@@_@@@@_@@@ i i:
_@@@@_@@@@N@@@@_@@ mmmmmmmmmmmmmmmmmm m@@@@m@@@@m@@@@m@@ mmmmmmmmmmmmmmmmmm
_@@@@_@@@@_@@@@_@@
J
See pages in the parentheses for details.
FrontPanel
ill!ill
Disc trays
Iii_i]Oil (standby/on) button and lamp (9, 12, 27, 28)
% ECO (Ecology) button (9)
Iii_]Remote sensor
% Display window
% FM/AM button (9, 13)
Pressing this button also turns on the unit.
Ii_i]TAPE _ _ button (9, 21, 22)
Pressing this button also turns on the unit.
% AUX button (9)
Pressing this button also turns on the unit.
Ill}i]CLOCK/TIMER button (10, 26 - 29)
If!fillIndication-lamp panel
@ SOUND MODE lamp (11)
% SUBWOOFER lamp (11)
Ii_i]REC (recording) lamp (22 - 24)
IiiO Effect Amplifier) mode lamps (11)
• ROCK, POP, and CLASSIC lamps
Ill Surround mode lamps (11)
• DANCE, HALL, and STADIUM lamps
Iii_ilCD ready lamps (14)
• CD1 READY, CD2 READY, and CD3 READY lamps
I)iii_l MODE control (11)
Ii_)lPRESET + / - control (13)
/ _ (reverse skip/forward skip) control
(10, 12, 17 - 19, 23, 24, 26 - 28)
If!fillSUBWOOFER
LEVEL + / - buttons (11)
If!fillSetting
buttons (8, 10, 12, 13, 18, 19, 24, 26 - 29)
• CANCEL/DEMO and SET/DISPLAY buttons
If!fillREVERSE
MODE button (21 - 24)
If!fillCassette
holder (21 - 24)
Ji!i_]
(0) jack (10)
If!fill& (Disc tray open/close) (CD1, CD2, and CD3) buttons
(14, 16, 17, 20)
Pressing one o[these buttons also turns on the unit.
I)il}lDisc number (CD1, CD2, and CD3) buttons (16 - 19, 23, 24)
Pressing one o[these buttons also turns on the unit.
I_l CD _/11 button (9, 17 - 19, 23, 25)
Pressing this button also turns on the unit.
I)i!] TUNING + / - buttons (13)
/ _ (reverse search/forward search) buttons (12, 17, 21)
• (stop) button (12, 17 - 25, 28)
I))] VOLUME + / - control (10, 25)
I_i_lDisc play mode buttons (18 - 20)
• REPEAT and CD PLAY MODE buttons
I_i_lMIC LEVEL control (25)
MIC 1 and MIC 2jacks (25)
I)_l Recording buttons (22 - 25, 28)
• REC START/STOP, CD REC START, and EDIT buttons
I)i_l A EJECT button for cassette deck (21 - 23)
Display Window
ill!ill]
indicators
• DAILY (Daily Timer), SLEEP (Sleep Timer),
REC (Recording Timer), and @ (Timer) indicators
Ii121] indicator
% GROUP indicator
Iii_]TRACK indicator
% Main display
• Shows the source name, frequency, etc.
% PRGM (program) indicator
Iii_i]Disc track number (1 - 16) indicators
% RANDOM indicator
Ill}i]REPEAT (ALL/I/DISC) indicators
I)iii_] level indicator
When one of the 6preset sound modes is activated, these will function as illumination display.
For details, see
"Selecting
the Sound Modes" on page 11.
Ii_)lTuner operation indicators
• MONO and ST (stereo) indicators
If!fillTape operation indicators
• _ _ (tape direction) and ('_) (reverse mode) indicators
Ii!ii_] and ECHO indicators
4
RemoteControl
JVC
RemoteControl
[]ii] Number buttons (13, 17, 18)
[12]_ (-_t._) (reverse skip/reverse search) button
(13, 17, 19, 21)
• (stop) button (17 - 19, 21 - 25, 28)
(IPq_) (forward skip/forward search) button
(13, 17, 19, 21)
% Disc number (CD1, CD2, and CD3) buttons (16 - 19)
Iii_i]Disc play mode buttons (18 - 20)
• REPEAT, RANDOM, and PROGRAM buttons
% REC START/STOP button (22, 24, 25, 28)
% SOUND MODE button (11)
[_?i]SUBWOOFER LEVEL + ! - buttons (11)
% STANDBY/ON Oil button (9)
[i{] SLEEP button (29)
[!ii_]AUX button (9)
I)iii!]FM!AM
button (9, 13)
[!i)] FM MODE button (13)
[!ii_]CD _/1!
button (9, 17 - 19, 25)
I]ii_]PROGRAM CANCEL button (19)
I]ii_]TAPE -.q _ button (9, 21, 22)
I]ii_]ECHO button (25)
KARAOKE button (25)
[!ii_]BEEP ON/OFF button (8, 9)
[!ii_]VOLUME +/button (10, 25)
I)il}]FADE MUTING button (10)
When using the remote control, point it at the remote sensor on the front panel.
5
GettingStarted
Continued I_
SuppliedAccessories
Make sure that you have all the following items.
The number in the parentheses indicates the quantity of the pieces supplied.
• AM loop antenna (1)
• FM antenna (1)
• Remote control (1)
• Batteries (2)
• AC plug adaptor (1)
If anything is missing, consult your dealer immediately.
Connecting Antennas
FM antenna
FM antenna (supplied)
Putting the Batteries into the Remote Control
Insert the batteries--R6(SUM-3)/AA(15F)--into the remote control, by matching the polarity (+ and -) on the batteries with the + and - markings on the battery compartment.
When the remote control can no longer operate the unit, replace both batteries at the same time.
1
Attach the FM antenna
to the FM 75 £2
COAXIAL terminal.
2
Extend the FM antenna.
3
Fasten it up in the position which gives you
the best reception,
then fix it on the wall, etc.
\
_About
the supplied
FM antenna
The FM antenna supplied with this unit can be used as temporary measure.
If reception is poor, you can connect an outdoor FM antenna.
2
R6(SUM-3)/AA(15F)
Toconnectan outdoorFM antenna
Before connecting it, disconnect the supplied FM antenna.
Outdoor FM antenna
(not supplied)
3
\
DO NOT use an old battery together with a new one.
DO NOT use different types of batteries together.
DO NOT expose batteries to heat or flame.
DO NOT leave the batteries in the battery compartment when you are not going to use the remote control for an extended period of time.
Otherwise, it will be damaged from battery leakage.
6
A 75 £_antenna with coaxial type connector should be used.
ConnectingSpeakers
AM antenna
p-
1
O
-ANTENNA_
m
..J
_inyl-covered
(not supplied) wire
3
(black/blue)
Speaker cords
/
%
//_k/blue
Speaker cords m
FM 75
-COAXIAL
CAUTION:SPE KER IMPED, _lC_ eaker cor_s_
AM loop antenna
(supplied)
1
If cords are covered with insulation, twist the core of the cord at the end of each cord, then remove the insulation.
From right subwoofer black/red)
]
From left subwoofer
From main right speaker
From main left speaker
2
Connect the AM loop antenna to the AM LOOP terminals as illustrated.
3
Turn the AM loop antenna until you have the best reception.
Toconnectan outdoorAM antenna
When reception is poor, connect a single vinyl-covered wire to the AM EXT terminal and extend it horizontally.
The AM loop antenna must remain connected.
If cords are covered with insulation, twist the core of the cord at the end of each cord, then remove the insulation.
2
Insert the end of the speaker cord into the terminal as illustrated.
Match the same polarity: (+) to (+) and (-) to (-).
3
Close the speaker terminals.
IMPORTANT: Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the unit.
_For
better reception of both FM and AM
•
Make sure the antenna conductors do not touch any other terminals and connecting cords.
• Keep the antennas away from metallic parts of the unit, connecting cords, and the AC power cord.
DO NOT connect more than one speaker to each speaker terminal.
DO NOT push or pull the speakers as this will damage the foot spacers at the bottom of the speakers.
7
ConnectingOtherEquipment
You can connect both analog and digital equipment.
Adjustingthe VoltageSelector
Before plugging in the unit, set the correct voltage for your area with the voltage selector on the rear of the unit.
._•
• DO NOT plug in any equipment until all connections are complete.
Toconnectan analog component
Be sure that the plugs of the audio cords are colored: White plugs and jacks are for left audio signals, and red ones for right audio signals.
RIGHT LEFT
VOLTAGE
SELECTOR
110V_
[-
Z2:.240Q._
f
J
Voltage mark
Use a screwdriver to rotate the voltage selector so that the voltage number and the voltage mark is pointing at the same voltage as where you are plugging in the unit. (See the back cover page.)
To audio output
RIGHT
Audio equipment
' '
For playing the other equipment through this unit,
connect between the audio output jacks on the other
equipment and AUX jacks by using an audio cord (not supplied).
procedures are complete.
Now, you can plug the AC power cord.
• If the wall outlet does not match the AC plug, use the supplied
AC plug adaptor.
Toconnectaudio equipmentwith an optical digital input terminal
You can record audio CD sound onto the connected digital equipment.
• If the disc played back is an MP3 disc, no sound can be output from the unit to the connected digital equipment.
I
MPORTANT: Be sure to check all connections to be done
Cancelingthe Demonstration
When connecting the AC power cord into a wall outlet, the unit automatically starts the demonstration.
r
CD OPTICAL
DIGITAL "_
OUTPUT
|
Protective plug
To cancel the demonstration,
CANCEL/DEMO until "DEMO press and hold
OFF" appears on the display.
• To cancel only beep sounds during the demonstration, press BEEP ON/OFF
on
the remote control.
BEEP
ON/OFF
Before connecting the other equipment, remove the protective plug from the terminal.
_When
you press other
buttons
The demonstration stops temporarily.
It will start automatically again (if no operation is done for 2 minutes) unless you cancel it by pressing CANCEL/DEMO.
To optical digital input
Audio equipment with an optical digital input i i i i
Tostart the demonstrationmanually
Press and hold CANCEL/DEMO appears on the display.
again until "DEMO START"
Connect an optical digital cord (not supplied) between the optical digital input terminal on the other equipment and the
CD OPTICAL DIGITAL OUTPUT terminal.
8
CommonOperations
TurningOnor Offthe Power
To turn on the unit, press O/I (or
STANDBY/ON Oil on the remote
control)
so that the lamp on the button goes off.
Fl u.F
_
'-'"
!
_/
To turn off the unit (on standby), press Oil
(or STANDBY/ON Oil on the remote control)
again so that the lamp on the button lights up.
• A little power is always consumed even while
the unit is on standby.
To switch off the power supply completely,
unplug the AC
power cord from the AC outlet.
--Ecology Mode
You can save the power consumption while the unit is turned off (on standby).
• You can set Ecology Mode whether the unit is on or off.
On the unit ONLY:
To activate
the Ecology
Mode,
press ECO.
"ECO" appears on the display for 2 seconds
(and the demonstration
is canceled if you have
pressed the button while the unit is off).
The clock is reset to "0:00" right away, while the tuner preset stations (see page 13) will be erased in a few days.
To deactivate
the Ecology
Mode,
press ECO again.
"NORMAL" appears (and the demonstration starts if the unit is turned off).
It l I--I
I--I
Iul I--I I
I_ILII "_" !lr'iL
TurningOnor Offthe Key-touchTone
If you do not want the key-touch tone to beep each time you press a button, you can deactivate it.
On the remote control ONLY:
Press BEEP ON/OFE
BEEP
ON/OFF
%
,_',E
I'-I
U
FF
• Each time you press the button, the key-touch tone turns on
("BEEP ON") and off ("BEEP OFF") alternately.
• Each time you press the button, "ECO" and "NORMAL" appear alternately on the display.
_When
you turn off the unit with Ecology Mode activated
"ECO" flashes on the display, and the clock time will not be shown
while the unit is turned off.
Selectingthe Sources
To listen to the FM/AM
broadcasts, press FM/AM.
(See page 13.)
To play back discs, press CD I_111. (See pages 14 - 20.)
To play back
tapes,
press TAPE -_ _.
(See page 21 .)
To select
the external equipment
as the source, press AUX.
BEEP OFF _ BEEP ON
When you press the play button for a particular source
(FM/AM, CD _/ll, TAPE -,9 _, and AUX), the unit turns on and the unit starts playing the source if it is ready.
-9-
Continued II_
Setting the Clock
You can set the clock whether the unit is on or off; however, if Ecology Mode is activated, you cannot set the clock while the unit is off (on standby).
If Ecology Mode is not in use while the unit is turned off (on standby), "0:00" flashes on the display until you set the clock.
On the unit ONLY:
1
Press CLOCK/TIMER.
The hour digits start flashing on the display.
K::?=_P_°7_
Adjustingthe Volume
You can adjust the volume level only while the unit is turned on. The volume level can be adjusted in 32 steps (VOLUME
MIN, VOLUME 1 - VOLUME 30, and VOLUME MAX).
TUrn VOLUME + / - clockwise (+)
to increase the volume or counterclockwise (-) to decrease it.
When using the remote control, press
VOLUME + to increase the volume or
VOLUME - to decrease it.
VOLUME
2
Turn _1< / _
to adjust the hour, then press SET/DISPLAY.
The minute digits start flashing
on the
display.
,
I .......
!__1
......
"'-" '"'"E
_
'5
_For
private listening
Connect a pair of headphones to the PHONES ( 0 ) jack.
No sound comes out of the speakers.
Be sure to turn down the volume before connecting or putting on headphones.
SET /
DISPLAY
If you want to correct the hour °"° ...... o after pressing SET/DISPLAY, press CANCEL/DEMO.
The hour digits start flashing again.
_..'_
\"
3
Turn _1< / _
to adjust the minute, then press SET/DISPLAY.
F1 '-' l
uL-
l U m
DO NOT turn off (on standby) the unit with the a sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the unit or start playing any source next time.
REMEMBER, you cannot adjust the volume level while the unit is off (on standby).
Tocheckthe clocktime while playinga source
Press and hold SET/DISPLAY.
• Each time you press and hold the button, the source indication and the clock time alternate on the display.
Toturn downthe volumelevel temporarily
On the remote control ONLY:
Press FADE MUTING.
The volume level gradually decreases to
"VOLUME MIN."
To restore
the sound, press the button again.
To adjust the clock again
If you have set the clock before, press CLOCK!TIMER
repeatedly until the clock setting mode is selected.
• Each time you press the button, the clock/timer setting modes change as follows:
(Daily Timer setting)
F DALLY "-_ TIMER "-"REC
L_ Canceled-.,--.,'TIMER j
(Recording Timer setting)
(The hour digits start flashing.)
When you unplug the AC power cord or if a power failure occurs
The clock loses the setting and is reset to "0:00." If this happens, set
the clock again.
-10-
Reinforcingthe BassSound
You can select one of the 5 subwoofer levels. This function only affects the playback sound, but does not affect your recording. The subwoofer level can be adjusted in 5 steps--
LEVEL 0 (MIN LEVEL), LEVEL 1, LEVEL 2, LEVEL 3, and LEVEL 4 (MAX LEVEL).
Press SUBWOOFER
LEVEL
+ to
increase the subwoofer level or
SUBWOOFER LEVEL - to decrease it.
SUBWOOFER lamp lights up in red.
• The SUBWOOFER lamp lights up in red when LEVEL 1 to
LEVEL 4 (MAX LEVEL) is selected.
The lamp turns off when
LEVEL 0 (MIN LEVEL) is selected.
Selectingthe SoundModes
You can select one of the 6 preset sound modes (3 surround modes and 3 SEA--Sound Effect Amplifier--modes) and 3 user modes. This function only affects the playback sound, but does not affect your recording. Each Sound Mode has its own illumination display.
To select the sound modes, turn
SOUND MODE (or press SOUND MODE
on the remote control) until the sound mode
you want appears on the display.
The sound modes change as follows: fr-_ DANCE _ HALL--_--STADIUM ---,--ROCK 7
OFF
(Canceled)
POP
When using the remote control, the sound mode changes only clockwise in the above sequence.
Surround modes*
DANCE:
Increases resonance and bass.
HALL:
Adds depth and brilliance to the sound.
STADIUM:
Adds clarity and spreads the sound, like in an
outdoor stadium.
SEA (Sound Effect Amplifier) modes
ROCK:
Boosts low and high frequency. Good for acoustic
music.
POP:
Good for vocal music.
CLASSIC:
Good for classical music.
User Modes
USER 1/2/3: Your individual mode stored in memory. See
"Creating Your Own Sound Mode--User
Mode" on page 12.
OFF:
The sound mode is canceled.
* Surround elements are added to the SEA elements to create a being-there feeling in your room.
"i"1I_--_I
r r x! ¢1
I_1 I-- !"-sgggg
•
When a sound mode is selected, the lamp for the selected sound mode (in this example, DANCE) flashes while the SOUND MODE and the other sound mode lamps light up.
• When one of the user modes (USER 1, USER 2, or USER 3) is selected, only the SOUND MODE lamp lights up.
• When the sound mode is canceled ("OFF" is selected), all sound mode lamps including the SOUND MODE lamp go off.
-11 -
CreatingYourOwnSoundMode--User Mode
You can change SEA pattern to suit your preference. The SEA pattern can be adjusted into 5 frequency ranges--LOW1,
LOW2, MID, HIGH1, and HIGH2. These changed settings can be stored in the USER 1, USER 2, and USER 3 modes.
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the unit ONLY:
1 Select one of the preset sound modes.
• If you want to add the surround elements in your SEA
pattern, select one of the surround modes (DANCE,
HALL, or STADIUM) before starting the procedure below. (See "Selecting the Sound Modes" on page 11 .)
2
Press SET/DISPLAY while the selected sound mode is still shown on the display.
SET#
DISPLAY
%
Turn I<< / _ to select one
of the user modes (USER
1,
USER 2, or USER 3) in which you want to store your
SEA pattern.
6 Press SET/DISPLAY
again.
lwl lwl I--I
IIEII!_IP_
"i
_"_'_
SET#
DISPLAY
The SEA pattern you have created are stored into the user mode selected in step 5.
To useyour ownsoundmode
Select USER 1, USER 2, or USER 3 mode when using the sound modes. See "Selecting the Sound Modes" on page 11.
I_IE
_
I_I
failure occurs the AC power cord or if a power
The setting will be erased in a few days.
If this
happens, set
the user modes again.
I I--II I I
.L
-=-I
l_
!_IH
I c_']]'_
Current level appears.
3
Adjust the SEA pattern.
1) Turn _ / _ to select the
frequency range (LOW 1, LOW2,
MID, HIGH1, or HIGH2).
Setting the AM Tuner Interval Spacing
Some countries space AM stations 9 kHz apart, and some countries use 10 kHz spacing.
On the unit ONLY:
You can only change the AM tuner interval spacing while
tuning in to an AM station. (See page 13.)
Press O/I while holding down I.
2) Press _ or _ to adjust the level (-3 to +3) of the selected
{_
frequency range.
3) Repeat steps 1) and 2) to adjust the level of the other frequency ranges.
4 Press SET/DISPLAY
again.
,_,'=_', Z;'......
_ _
.....
SET#
DISPLAY
%
• Each time you press these buttons, the AM tuner interval spacing alternates between 9 kHz and 10 kHz.
-12-
Listeningto FM andAM Broadcasts
Tuning in to a Station
1
Press FM/AM.
The unit automatically turns on and tunes
in to the previously received station (either
FM or AM).
• Each time you press the button, the band
alternates between FM and AM.
/AM
On the unit ONLY:
1 Tune in to the station
you want to preset.
• See "Tuning in to a Station."
2
Press SET/DISPLAY.
SET/
DISPLAY
%
2
Start searching for stations.
On the unit:
Press and hold TUNING + or TUNING
- for more
than 1 second.
...........
• JNING ..........
-]"
On the remote
control:
Press and hold _
(_).-)
or _1< (<<)
for more
than 1 second.
_7_
The unit starts searching for stations and stops when a station of sufficient signal strength is tuned in.
• If a program is broadcast in stereo, the ST (stereo) indicator
lights up.
To stop searching, press TUNING + or TUNING - (or
_t (l,q_) / _ (<<) on the remote control).
3
Turn PRESET
+ / - to select a
.....
_,-
preset number.
r" ""
_ _ _
i'
4
Press SET/DISPLAY again,
'3"-' -
__
__ og_Y
The tuned station in step 1 is stored in the preset number selected in step 3.
• Storing a new station on a used number erases the previously stored one.
When you press TUNING
+
or TUNING - (or _
(IH_) /
The frequency changes step by step.
When you unplug the AC power cord or if a power
The preset stations will be erased in a few days. If this happens, preset the stations again.
To changethe FM receptionmode
On the remote control ONLY:
When an FM stereo broadcast is hard to receive or noisy, press FM MODE so that the MONO indicator lights up on the display.
Reception improves.
FM.ODE
To restore the stereo
effect,
press FM MODE again so that the MONO indicator goes off. In this stereo mode, you can hear stereo sounds when a program is broadcasted.
Presetting Stations
You can preset
30 FM and 15 AM stations.
In some cases, test frequencies have been already memorized for the tuner since the factory examined the tuner preset function before shipment.
This is not a malfunction.
You can preset the stations you want into memory by following the presetting method.
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.
Tuning in to a Preset Station
1
Press FM/AM.
The unit automatically turns on and tunes
in to the previously received station (either
FM or AM).
• Each time you press the button, the band
alternates between FM and AM.
2
Select a preset number.
On the unit:
Turn PRESET + / -.
On the remote control:
Press the number buttons.
Ex.: For preset number 5, press 5.
For preset number 15, press
+10, then 5.
For preset number 25, press
+10, +10, then 5.
For preset number 30, press
+10, +10, then 10.
@
@
@
@
@@
@@
@@
/AM
-13-
Disc Play Introduction
Continued I_
This unit has been designed to play back the following discs:
• CD (Audio CD)
• CD-R (CD-Recordable)
• CD-RW (CD-ReWritable)
• MP3 disc (MP3 files recorded on a CD-R or CD-RW)
When playinga CD-R orCD-RW
User-edited CD-Rs (CD-Recordable)
(CD-ReWritable)
"finalized." and CD-RWs can be played back only if they are already
• You can play back your original CD-Rs or CD-RWs recorded in music CD format or in MP3 format.
(However, they may not be played back depending on their characteristics or recording conditions.)
• Before playing back CD-Rs or CD-RWs, read their instructions or cautions carefully.
• Some CD-Rs or CD-RWs may not be played back on this unit because of their disc characteristics, damage or stain on them, or if the player's lens is dirty.
• CD-RWs may require a longer readout time. This is caused by the fact that the reflectance of CD-RWs is lower than for regular discs.
MP3 Introduction
What is MP3?
MP3 is an abbreviation of Motion Picture Experts Group 1
(or MPEG-1) Audio Layer 3. MP3 is simply a file format with a data compression ratio of 1:10 (128 kbps*).
By using
MP3 format, one CD-R or CD-RW can contains 10 times as much data volume as a regular CD can.
* Bit rate is the average number of bits that one second of audio data will consume. The unit uses kbps (l,000 bits per second). To get a better audio quality, choose a higher bit rate. The most popular bit rate for encoding (recording) is 128 kbps.
MP3 disc structure
On an MP3 disc, each song (material) is recorded as a file.
Files are grouped into a directory (or folder).
Directories can also include other directories, creating hierarchical directory layers.
(See "How are MP3 files recorded and played back?" on page 15.)
This unit manages files and directories as "tracks" and "groups."
This unit can recognize up to 255 tracks per disc, up to 64 groups per disc. The unit ignores those exceeding the maximum numbers and cannot play them back.
About the CD ready lamps
Each CD ready lamp corresponds to the disc tray of the same number.
When and why they light up?
- When you turn on the unit for the first time after
plugging
into a wall outlet, all CD ready lamps (CD1
READY,
CD2 READY, and CD3 READY)
light up.
From the next time on, CD ready lamp(s)
light(s) up according
to the previous
condition.
- Each time you press the disc tray open/close
buttons
--_ (CD1, CD2, and CD3), the corresponding CD ready
lamp lights up.
When and why they go off?.
Only when the unit detects there is no disc loaded on a
certain tray, the corresponding CD ready lamp goes off.
("NO DISC 1," "NO DISC 2," or "NO DISC
3"
appears on the display.)
When and why they flash?
The corresponding CD ready lamp flashes during
playback and pause.
_About
MP3 discs
• MP3 discs (either CD-R or CD-RW) require a longer readout time.
(It varies due to the complexity of the recording configuration.)
° When making an MP3 disc, select ISO 9660 Level 1 or Level 2 as the disc format.
° This unit does not support multisession recording.
° This unit can play MP3 files only with the following file extensions--
".MP3," ".Mp3"' ".mP3," and ".mp3."
° Files other than MP3 are ignored.
° Some MP3 discs may not be played back because of their disc characteristics or recording conditions.
_If
The corresponding
light up.
the loaded
disc is an MP3 disc
CD ready lamp and the MP3 indicator will
-14-
How are MP3 files recorded and played back?
MP3 "tracks (files)" can be recorded in "group"--folders directories, in PC terminology.
During recording, the tracks and groups can be arranged similarly to the tracks and folders/directories of computer or data. "Root" is similar to the root of a tree. Every track and group can be linked to the root.
In compliance with ISO 9660, the maximum allowable depth of nested directories--so
(inclusive of the root).
called "hierarchy"--is eight
Playback order, track search order, and group search order of the MP3 tracks recorded on a disc are determined by the writing (or encoding) application; therefore, playback order may be different from the one you have intended while recording the groups and the tracks.
The illustration shows an ordinary example of how MP3 tracks are recorded on a CD-R or CD-RW, how they are played back and how they are searched for on this unit.
• The numbers in circles next to the MP3 tracks (_') indicate the playback order and search order of the MP3 tracks.
Normally this unit plays back MP3 tracks in the recorded order.
• The numbers inside the groups indicate the playback order and search order of the groups on an MP3 disc. Normally this unit plays back MP3 tracks in the groups in the recorded order.
The groups marked with asterisk (*) will be skipped since they do not include any MP3 tracks.
MP3 orouo/trackconfiouration: i i i i i i i
E
_-[_®
,._®!
_/>
Groups
MP3 tracks
j'-
_._@
__
__
-15-
PlayingBackDiscs
Loading Discs
On the unit ONLY:
1
Press
_
for the disc tray
(CD1, CD2, or CD3) you want to load a disc onto.
The unit automatically turns on
and the disc tray comes out.
2
Place a disc correctly on the circle of the disc tray, with its label side up.
I
CORRECT INCORRECT
• When using a CD single (8 cm), place it on the inner circle of the disc tray.
3
Press the same _
you have pressed in step 1.
The disc tray closes.
4 Repeat
steps 1 to 3 to place other discs.
_When
loading more than one disc
When you press • for the next tray you want to place another disc
onto, the first disc tray automatically closes and then the next tray
comes out.
Continued II_
Playing Backthe Entire Discs--Continuous Play
[I
You can play discs continuously.
• If you start Continuous Play with an MP3 disc, you can select a track you want to start playback with.
• For audio CDs
1
Load discs.
2
Press one of the disc number
cD3
(CD1, CD2, or CD3) buttons for the disc you want to play.
The unit searches for the disc, and starts playing with the first track of the selected disc.
Track number Elapsed playing time
/
U'U
....
TRACK
[_
_
Ii ii
--
I.
Tracks of the currently playing CD (Track numbers exceeding 16 are not displayed.)
• For MP3 discs
1
Load
discs.
2
Press one of the disc number
(CD1, CD2, or CD3) buttons for the disc you want to play.
The unit searches for the disc (it may
takes time), and the following information
appears on the display.
cD3
Total track number Total playing time
XnA¢ €
,__,,'-
:,. "---',:,
-16-
T
n n i UU
I
I
Group number flashes.
* If the group title cannot be shown at a time (exceeding
10 characters), the title scrolls.
°_'_
_°_°
3
Select a track to start playing with.
1)
Turn _ / _ (or press 1-91_I(_1)
/
(l_l_) on the remote
control) to
select a group you want, then press
CD I,,-I II.
The track number starts flashing.
2)
Turn _ / _ (or press 1-91_I(-_1_1)/
(IP-I_)on the remote control) to select a track you want to start playback with, then press CD I_/ll again.
enoop
XnACK
Basic Disc Operations
While playing a disc, you can do the following operations.
To exchange discs during playback of another
Press _ corresponding to a disc, not playing or selected currently, to eject and exchange the disc.
If you exchange discs during play, the current play will not stop until all discs you have exchanged are played.
Tostopplayfor a moment
Press CD I_/11.
While pausing, the elapsed playing
time
flashes on the display.
To resume playing,
press CD l_/ll
again.
%
Track title**
"TI'TLB r lul u
II _
Group number
F'---'"
-
MI,._
T i -'o_
Elapsed playing time
Togo to anothertrack
For audio CDs:
Before or during play
For MP3 discs: During play
Turn _ / _ (or press I.,91_1
(IP-I_) on the remote control).
/
• _ (or t._
(_1_1)):
Goes back to the beginning of the current or previous tracks.
• _ (or I,_ (I_)):
Skips to the beginning of the next or succeeding tracks.
VRACK
Ill
I|_ I.
u.P
Track number
** Only a maximum of 10 characters (including spaces between words) can be shown on the display. The exceeding characters will be ignored.
Playback starts with the selected track of the selected group.
To stop playing, press I.
To remove the disc, press _ for the corresponding disc tray.
Discplaybacksequence
When 3 discs* are loaded on the disc trays, they are played in one of the following sequences.
• When CD1 is pressed: CD1 =b CD2 =b CD3 (then stops)
• When CD2 is pressed: CD2 =b CD3 =b CD1 (then stops)
• When CD3 is pressed: CD3 =b CD1 =b CD2 (then stops)
* When no disc is loaded on the tray, that disc number is skipped.
"NO DISC 1," "NO DISC 2," or "NO DISC 3" appears on the display if the selected disc tray is empty.
Tolocate a particularpointin a track
During play, press and hold _ or
(or I_1_1('ql_l) / _ (1_,_) on the remote control).
• _ (or _
• _ (or _
(-,ql_l)): Fast-reverses
(1_,_)): Fast-forwards
{_
the disc.
the disc.
Togo to anothertrack directlyusingthe number buttons
On the remote control ONLY:
Pressing the number button(s) before or during play allows you to start playing the track number you want.
Ex.: For track number 5, press 5.
@@
For track number 15, press +10, then 5.
@@
For track number 20, press +10, then 10.
@@
For track number 32, press +10 three times, then 2.
For track number 132, press + 10 thirteen times, then 2.
-17-
Continued I_L
Programmingthe PlayingOrderof theTracks
--Program Play
You can arrange the playing order of the tracks before you start playing.
You can program up to 50 tracks.
• To use Repeat Play (see page 20) for Program Play, press
REPEAT after starting Program Play. Only REPEAT 1 and
REPEAT ALL can be selected for Program Play.
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step ,2 again.
1
Load
discs.
• If the current playing source is not the CD player, press
CD _/ll, then • before
going
to the next step.
2
Activate the Program Play mode.
On the unit:
Press CD PLAY MODE repeatedly
until "CD PROGRAM"
appears on the display.
• Each time you press the button, the play
mode changes as follows:
°_g#*
--.-CDR NDOM
:_celed
(Continuous Play)
On the remote control:
Press PROGRAM so that
"CD
PROGRAM" appears on the display.
PROGRAM
I-I-
I-I
III
h4
I--
PnQM
• The PRGM (program) indicator lights up on the display.
3 Press one of the disc number
(CD1,
CD2, or CD3) buttons to select the disc you want to play.
Track number
co3
I__ ""
+DD ....
oo
ILI "" J--
Disc number
Program step number
4 Select a track from the selected
disc in step 3.
On the unit:
Turn _<
/ _
to select the track number, then press
SET/DISPLAY.
On the remote
control:
Press the number buttons.
@
• For how to use the number buttons, see "To go to another @ track directly using the number buttons" on page 17.
@
Q
SET/
DISPLAY
%
@@
@@
@@
5 Program
other tracks you want.
• To program tracks from the same disc, repeat step 4.
• To program tracks from a different disc, repeat steps 3 and 4.
6
Press CD l_/ll.
The tracks are played in the order you have programed.
• If the playing disc is an MP3 disc, the
MP3 indicator lights up.
To stop playing, press •.
To exit from Program
Play mode,
press CD PLAY MODE repeatedly until the PRGM (program) indicator goes off (or press
PROGRAM on the remote control) after playback stops.
•
If you try to program a 51 st track, "CD FULL" will be flashing on the display.
° If you have tried to program a track from an empty tray, "NO
DISC 1," "NO DISC 2," or "NO DISC 3" will appear on the display for 2 seconds.
° If the track number you have programed does not exist on the disc, it will be skipped during play.
-18-
To checkthe programcontents
On the remote control ONLY:
Before playing, you can check the program contents by pressing
(<_) or _ ()_,_).
• _ (<t_) " Shows the programed tracks in the reverse order.
_..'_,,.
\"
• _ (I_,_) : Shows them in the programed order.
To modifythe program
Before or after playing, you can erase the last programed tracks by pressing CANCEL/DEMO
(or press PROGRAM CANCEL on the remote control).
• Each time you press the button, the last programed track is erased from the program.
PROGRAM
CANCEL
Playingat Random--RandomPlay
The tracks of the currently selected disc will be played at random.
• To use Repeat Play (see page 20) for Random Play, press
REPEAT after starting Random Play. Only REPEAT 1 and
REPEAT ALL can be selected for Random Play.
1 Load a disc.
2
Press the corresponding disc number (CD1,
CD2, or CD3) button where a disc is loaded in step 1, then press I1.
co3
To add tracks in the program before playing, simply select
the track numbers you want to add by following step 4 of the programming procedure. If you want to add tracks from
another disc, follow steps 3 and 4.
To erase the entire program before or after playing, press
and hold • until "CD PROGRAM" appears on the display.
• The program you have made will be erased,
- when you exit from Program Play mode,
- when you unplug the AC power cord, or
- when a power failure occurs.
3
Activate the Random Play mode.
On the unit:
Press CD PLAY MODE repeatedly
until "CD RANDOM"
appears on the display.
• Each time you press the button, the play
mode changes as follows:
CD PROGRAM _
Cancele,J•
N _M
(Continuous Play)
On the remote control:
Press RANDOM
so that
"CD RANDOM"
appears on the display.
°_g_Y
.,.oo.
_ iL!
±11_11 I_
Plll_l
• The RANDOM indicator also lights up on the display.
4
Press CD I)/11.
The tracks are randomly played.
Random Play ends when all the tracks
of the current disc are played once.
CD
I_/11
%
To skip the currently playing track, turn _ / _
to the
right (or press _ (I_,_) on the remote control).
-19-
If you turn t4< / _ to the left (or press t4< (<t_l) on
the remote control)
You cannot go back to the previous tracks during Random Play.
To stop playing, press •.
To exit from Random
Play mode,
press CD PLAY MODE repeatedly until the RANDOM indicator goes off (or press
RANDOM on the remote control) after playback stops.
Prohibiting Disc Ejection--Tray Lock
RepeatingTracksor Discs--Repeat Play
You can have all the discs, the program or the individual track currently playing repeat as many times as you like.
You can prohibit disc ejection from the unit and lock discs.
• This operation is possible only when the source is the CD player.
To repeat playing,
press REPEAT during or before play.
• Each time you press the button, Repeat Play mode changes as follows:
REPEAT ALL "--,'-- REPEAT 1DISC --
REPEAT
%
-Canceled _ REPEAT 1 -.,,-
The Repeat Play mode indicator lights up on the display.
For audio CDs: r vl
•
On
the unit
ONLY:
To prohibit
disc ejection, press _ for any disc tray while holding down I1. (If there is any disc tray opened, close it first.)
I
n.2
-io 0 iil
nEPlAT ALL
"LOCKED" appears for a while on the display, and the loaded discs are locked.
I
L
I-It Ip E TI
For MP3 discs:
QnouP
I.
'
XnAeK
I
'fi
.
'-'2" .....
ups
nl,ur
ALL
i
To cancel the prohibition and unlock
the discs, press _ for any disc tray while holding down
II.
"UNLOCKED" appears for a while on the display, and the loaded discs are unlocked.
REPEAT ALL:
During Continuous Play
Repeats all the tracks on all the loaded discs continuously.
During Program Play
Repeats the program.
During Random Play
Repeats all the tracks on all the loaded discs randomly.
REPEAT
1DISC:
Repeats all the tracks on the current disc continuously.
REPEAT
1:
Repeats the currently playing track.
I II_II rlr Ip r TI
I_II_II_ I_IL i'_I"_ il
_If
"LOCKED"
you try to eject
discs while Tray Lock is in use
appears to inform you that the disc trays are locked.
To cancel
Repeat
Play, press REPEAT repeatedly until the
Repeat Play mode indicators go off from the display.
° "REPEAT 1DISC" cannot be selected for Program Play or
Random Play
It is canceled when you select Program Play or Random Play.
° "REPEAT
ALL" cannot function
Place discs on all disc trays.
- 20 -
PlayingBackTapes
You can play back type I tapes without changing any settings.
PlayingBacka Tape
1
Press _ EJECT
for the cassette deck.
Toplay bothsidesrepeatedlymReverseMode
When using Reverse Mode, the tape automatically reverses at the end of one side, starts playing the other side of the tape, and repeats the same process.
On the unit ONLY:
To use Reverse Mode, press REVERSE MODE
SOthat the Reverse Mode indicator lights up on
the display like--(_).
To cancel Reverse Mode, press the button again so that the
Reverse Mode indicator lights up on the display like--Z.
2
Insert a cassette tape down.
with the exposed part of the
Locatingthe Beginningof a SongmMusicScan
You can use Music Scan to locate the beginning of a song.
Music Scan searches for blank portions that usually separate recorded songs, then plays the next song.
Tofind the beginningof the currentsong
During play, press _ or _
(or _ (-,_1) / _ (),-I_) on the remote control) in the opposite direction to the tape play.
The tape direction indicator of the
_
LSJ
opposite direction to the tape play starts flashing intermittently.
3
Close the cassette holder gently.
4
Press TAPE _ l*.
The tape play starts and the tape direction
TAC_:_AP_-
indicator (_ or _) starts flashing slowly
to indicate the tape running direction.
• Each time you press the button, the tape direction
changes
and "REVERSE" appears for a while on the display.
I_ : plays the front side.
._1 : plays the reverse side.
• If no cassette is inserted, "NO TAPE" appears on the display.
When the tape plays to the end, the deck automatically stops if the Reverse Mode is off. (See "To play both sides repeatedly--Reverse Mode.")
Searching stops automatically at the beginning of the current song, and it starts automatically.
Tofind the beginningof the nextsong
During play, press _ or _
(or _ (-,_1) / _ (),-I_) on the remote control) in the same direction as the tape play.
The tape direction indicator of the same direction as the tape play starts flashing intermittently.
Searching stops automatically at the beginning of the next song, and it starts automatically.
To stop playing, press I.
To fast-wind
to the left or to the right, press _ or _ (or
(-_14) / _ (1)q_) on the remote control) while the tape
is not running.
The tape direction indicator (_ or a) starts flashing
quickly
on the display.
To remove the cassette, press _ EJECT to open the cassette holder.
_
between each song, so it will not work well in the usic Scan works by detecting a 4-second long blank following cases
* No blank at the beginning of a song.
* Noise (often caused by much use or poor quality dubbing) which
fills the blank.
, Long, very soft passages or pauses in a song.
The use of the C-120 or thinner tape is not recommended, since characteristic deterioration may occur and this tape easily jams in the pinchrollers and the capstans.
-21 -
Recording
Continued I_K
IMPORTANT:
• It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.
• The recording level is automatically set correctly, so it is not affected by the VOLUME, the SUBWOOFER LEVEL, and the SOUND MODE controls. Thus, during recording you can adjust the sound you are actually listening to without affecting the recording level.
• If there are excessive noise or static in the recording you have made, the unit may be too close to a TV. Increase the distance between the TV and the unit.
• You can use type I tape for recording.
Recordingon a Tape
EJECT
cassette with the exposed part of the tape down.
To protectyour recording
Cassettes have two small tabs on the back to protect from unexpected erasure or rerecording.
To protect your recording, remove these tabs.
/%
To re-record on a protected tape, cover the holes with adhesive tape.
Tokeepthe best recordingand playbacksound quality
If the heads, capstans, and pinch rollers of the cassette deck become dirty, the following will occur:
• Impaired sound quality
• Discontinuous sound
• Fading
• Incomplete erasure
• Difficulty in recording
To clean the heads, capstans,
and pinch rollers
Use a cotton swab moistened with alcohol.
-Pinch rollers --
Capstans
2
Close the cassette holder gently.
• If you want to record on both sides of a tape, see "To record on both sides--Reverse Mode."
3
Check the tape direction of the cassette deck.
• If the tape direction is not correct, press TAPE < _ twice then • to change the tape direction.
4
Start playing the source--FM, AM, CD player,
or auxiliary
equipment connected to AUX jacks.
• When the source is the CD player, you can also use
Direct Recording--(see page 23), and Auto Edit
Recording (only for audio CDs)--(see page 24).
5
Start recording.
On the unit:
Press REC START/STOP.
On the remote control:
Press and hold REC START/STOP for more than 1 second.
REC START
/ STOP
%
The REC (recording) lamp flashes when recording starts,
and the tape direction indicator (I_ or <) starts flashing slowly.
• If no cassette is inserted, "NO TAPE" appears on the display. If a protected tape is inserted, "NO REC"
appears on the display.
Heads
To stop recording
immediately,
press REC START/STOP
or • (or press and hold REC START/STOP on the remote
control
for more than 1 second).
To remove the cassette,
press _ EJECT to open the cassette
holder.
To demagnetize the heads
Turn off the unit, and use a head demagnetizer (available at
electronics
and audio shops).
To recordon bothsidesmReverse Mode
On the unit ONLY:
Press REVERSE MODE so that the Reverse Mode .....
indicator lights up on the display like--('_).
• When using the Reverse Mode for recording, start recording in the forward (_) direction first.
Otherwise, recording will stop when only one side (reverse) of the tape is recorded.
To cancel Reverse Mode, press the button again so that the
Reverse Mode indicator lights up on the display like--7_.
- 22 -
SynchronizedRecording
By using Synchronized Recording methods, you can start and stop both disc play and tape recording at the same time.
Synchronized Recording consists of the following:
• Direct Recording
• Auto Edit Recording (only for audio CDs)
• DirectRecording
Everything on the disc goes onto the tape in the order it is on the disc, or according to the order you have made for
Program Play.
On the unit ONLY:
1 Press _ EJECT and insert a recordable cassette
with the exposed part of the tape down.
4
Press CD REC START.
°:T;g
"CD REC" appears on the display and the
REC (recording) lamp flashes when recording starts.
The cassette deck starts recording while the
CD player starts playing.
When the recording is done, "CD REC FINISHED"
appears scrolling on the display, and the REC (recording)
lamp turns off. Both the cassette deck and the CD player stop automatically.
To stop recording, press • to create a 4-second blank portion on the recording tape. (Remember, a 4-second blank is important when using Music
Scan--see page 21.)
Torecordon bothsides--Reverse Mode
On the unit ONLY:
Press REVERSE MODE so that the Reverse Mode .....
indicator lights up on the display like--('_).
• When using the Reverse Mode for Direct
Recording, start recording in the forward (_) direction first. When the tape reaches its end while recording a song in the forward direction (_), the last song will be re-recorded at the beginning of the reverse side (-ql).
If you start recording on the reverse side (-ql) first, recording will stop when only one side (reverse) of the tape is recorded.
To cancel Reverse Mode, press the button again so that the
Reverse Mode indicator lights up on the display like--Z.
2
Load a disc.
3
Select a disc.
For audio CDs:
Press the corresponding disc number
(CD1, CD2, or CD3) button where a disc is loaded in step 2, then press m.
For MP3
discs: cD3 co2
CDt
You can select a track to start recording with.
1) Press the corresponding disc number
co3
(CD1, CD2, or CD3) button where a co2 F===Y_ disc is loaded in step 2.
CD1
2) Turn _ / _ to select the group, then press CD I_/ll.
3) Turn _ / _ to select the track.
- 23 -
• Auto Edit Recording (only for audio CDs)
Using Auto Edit Recording, you can record the tracks on a
CD onto both sides of the tape. However, if the tracks are recorded segmentally starting from track 1, the track recorded on the end portion of the front side of the tape may be cut off; to prevent this, the unit automatically selects an appropriate-length track so it fits the remaining tape length properly.
On the unit ONLY:
1 Load a disc.
2
Press the corresponding disc
°°3 r_7
number
(CD1, CD2, or CD3)
button where a disc is loaded
0°2 co,
in step 1, then press •.
• If there is no disc on the selected disc tray, "NO DISC 1,"
"NO DISC 2," or "NO DISC 3" appears, and the unit
continues
to search for a disc from another disc tray.
3
Press EDIT.
EDIT
%
"r
, ,,PE I:
5 Insert a recordable
cassette of appropriate
length into the cassette deck.
6
Press REVERSE MODE so that
,E2gg
the Reverse Mode indicator lights up likem(_).
• Without turning on the Reverse Mode, recording will stop when the front side of the tape is recorded.
7
Press CD REC START.
c_.;g
"CD REC" appears, then "TAPE SIDE-A
STAND-BY" scrolls on the display, and the
REC (recording) lamp flashes.
The cassette deck starts recording.
About 10 seconds later, the CD player starts playing.
When the recording is done, "CD REC FINISHED" scrolls on the display and the REC (recording) lamp turns off. Both the cassette deck and CD player stop automatically.
• If a tape has not been rewound, the cassette deck will rewind the tape before it starts recording.
• A 10-second blank portion is automatically created at the beginning of each side of the tape.
To stop during Auto Edit Recording
Press REC START/STOP or • to create a 4-second blank portion on the recording tape. (Remember, a 4-second blank is important when using Music Scan--see page 21 .)
To cancel Auto Edit Recording
Press CANCEL/DEMO before or after recording.
T|--!
I--I--I
, ,"iF'I-_i,_F',i,_,
The optimum tape length for the disc appears.
To change the tape length
manually
If the tape length selected is not satisfactory, you can change the tape length by turning _ / _ on the unit.
You can select the tape length among the following
--40, 46, 50, 54, 60, 64, 70, 74, 80, 84, and 90.
4 Press SET/DISPLAY.
• Each time you press the button,
the tracks
to be recorded on the front side ("SIDE-A')
and on the reverse side ("SIDE-B')
appear alternately
on the display.
Tracks to be recorded on the reverse side (SIDE-B) appear.
SET/
DISPLAY
%
- 24 -
Usingthe Microphones
You can enjoy singing along (Karaoke) and microphone mixing by using two microphones.
• MIC LEVEL adjustment is valid for both microphones connected to MIC 1 and MIC 2 jacks.
If howling or squealing
(feedback)
the microphone(s) occurs while
Take the following
actions to prevent these noises.
• Adjust MIC LEVEL and the volume level.
• Avoid pointing
the microphone(s) towards
the speakers.
• When two microphones are connected,
turn off the ON/OFF switch
on the unused microphone.
using
IMPORTANT:
• Always set MIC LEVEL to MIN when connecting or
disconnecting the microphone.
• When you do not use the microphone, keep the microphones
unconnected.
Singingalong--Karaoke
• VocalMasking
Vocal Masking reduces the lead vocal of the playing source, and allows you to replace it by singing into the microphones as the music plays.
MIC LEVEL
1
Turn MIC LEVEL to MIN.
{(_
MIN
2
Connect the microphone(s) (not supplied) by plugging it into MIC 1 and/or MIC 2 jack(s).
3
Press KARAOKE on the remote
,_o,_
control.
"KARAOKE" appears for 2 seconds and
KARAOKE indicator lights up and remains lit.
If you use the following sources as the playing source for Karaoke
(Vocal
Masking), you cannot get the satisfactory results
• Radio programs--a radio signal is not as reliable as the signals
coming
from a tape or a disc.
• Monaural sources.
° Poorly dubbed tapes.
° Sources recorded with duets, strong echo, a chorus, or only a few instruments.
• MicrophoneMixing
When you sing along with multiplex tapes or discs, follow the procedure below:
1
Connect the microphone(s).
2
Start playing the sourcemdisc, tape, or other connected component.
3 Adjust
MIC LEVEL and the volume level as you sing into the microphone(s).
• By pressing REC START/STOP, you can record your singing along if you want. (For more details, see page 22.)
4
Start playing the sourcemdisc, tape, or other connected component.
5 Adjust
MIC LEVEL and the volume level as you sing into the microphone(s).
• By pressing REC START/STOP, you can record your singing along if you want. (For more details, see page 22.)
To use microphoneonly
Without any background sound, you can use your microphone(s), and record it if you want.
1
Connect the microphone(s).
2 Press CD l_/ll, then II.
No background sound will be heard.
To cancel Vocal Masking,
press KARAOKE on the remote control again.
• "OFF" appears for 2 seconds and the KARAOKE indicator goes off. Normal stereo play back resumes.
To applyan echoto yourvoice
On the remote control ONLY:
Press ECHO so that the ECHO indicator lights up on the display.
• Each time you press the button, the echo level changes as follows:
_°"°
_" ECHO 1 -ECHO 2-ECHO 3 _
ECHO OFF ,,,,
(Canceled)
As the number increases, a stronger echo effect applies to your voice.
3 Adjust MIC LEVEL and the volume level as you sing into the microphone(s).
• By pressing REC START/STOP, you can record your singing along if you want. (For more details, see page 22.)
- 25 -
_)
Usingthe Timers
Continued I_
There are three timers available--DAILY (Daily Timer), REC
(Recording Timer), and SLEEP (Sleep Timer).
You can set the timers whether the unit is on or off; however, if Ecology Mode is activated, you cannot set the timers while the unit is off.
Before using the timers, set the clock built in the unit. (See page 10.)
On the unit ONLY:
1
_o[_
appears on the display.
The @ (Timer) indicator lights up and the DAILY (Daily
Timer) indicator also starts flashing on the display.
UsingDaily Timer
With Daily Timer, you can be wake up with your favorite music or radio program.
--
_ip
• Each time you press the button, the timer setting modes change as follows:
How DailyTimer actually works
The unit automatically turns on, sets the volume level to the preset level, and starts playing the specified source when the on-time comes.
("DAILY" and the DAILY indicator flash just before the on-time, and the DAILY indicator continues flashing while the timer is operating.) Then, when the offtime comes ("DAILY OFF" flashes just before the off-time), the unit automatically turns off (on standby).
The Daily Timer works everyday automatically.
If you do not want to use the Daily Timer, turn it off. (See "To turn on or off Daily Timer after its setting is done" on page 27.) The timer setting remains in memory until you change it.
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
• To correct a misentry while setting the timer, press
CANCEL/DEMO.
Before you start...
• When using a disc as the source to play-
- Make sure there is a disc on the selected disc tray.
• When using a tape as the source
to play-
- Make sure that a tape is in the cassette deck.
- Make sure that the tape direction is correct.
• When using
the external component as the source to play-
- Set the timer equipped on the external component at the same time.
TIMER "-" REC
Canceled -,-Clock _ TIMER j setting
(Recording Timer setting)
(The hour digits star flashing.)
2
Press CLOCK/TIMER again.
"TIMER" appears for 2 seconds,
then the
unit enters
on-time
setting
mode.
:
........
......
C:?q_?_o_._
n
3
Set the on-time you want the unit to turn on at.
1)
Turn _ / _ to set the hour, then press
SET/DISPLAY.
"SET" appears for 1 second.
2)
Turn _ / _ to set the minute,
then press
SET/DISPLAY.
"SET" appears for 1 second,
then
the unit enters
off-time
setting
mode.
F F n
SET/
DISPLAY
- 26 -
4
Set the off-time you want the unit to turn off
(on standby)
at.
1) Turn _ / _ to set the hour, then press
SET/DISPLAY.
"SET" appears for 1 second.
2) Turn _ / _ to set the minute, then press
SET/DISPLAY.
"SET" appears for 1 second, then the unit enters source selecting mode.
8
Press SET/DISPLAY to complete the Daily Timer setting.
The DAILY (Daily Timer) indicator stops flashing and remains lit. "OK J" appears on
the display for 2 seconds.
The settings you have done are shown on the display in sequence for your confirmation.
9
Press O/I to turn off the unit (on
standby) if you have set the Daily
Timer with the unit turned on.
SET/
DISPLAY
5
Turn _<
/ _
to select the source to play, then press SET/DISPLAY.
"SET" appears for 1 second.
• The source changes as follows:
_ TUNER FM --.,_,"- TUNER AM q
AUX IN -..,,--,..- 1 CD-- 1
TUNER FM: tunes in to a specified preset FM station.
-* Go to step 6.
TUNER AM: tunes in to a specified preset AM station.
-* Go to step 6.
1 CD-- 1: plays from a specified track of a specified disc. --* Go to step 6.
TAPE:
plays a tape in the cassette deck.
-_ Go to step 7.
AUX IN:
plays an external source. -_ Go to step 7.
6
When selecting ''TUNER FM" or"TUNERAM"
Turn _ / _ to select the preset station number, then
press SET/DISPLAY.
The unit enters volume setting mode.
When selecting
"1 CD-- 1"
1) Turn _ / _ to select the disc number, then press
SET/DISPLAY.
"SET" appears for 1 second.
2) Turn _ / _ to set the track number, then press
SET/DISPLAY.
"SET" appears for 1 second, then the unit enters volume setting mode.
7 Turn _< / _
to set the volume level.
• The volume level changes as follows:
• If the unit is turned on before the on-time comes
Daily
Timer does not work.
• Even if you unplug the AC power cord or if a power failure
occurs
Once you set the
timer, the timer
setting
mayremain stored in
memoryin a few days.
In this case, check whether the timer setting still remains or not.
Toturn on or off Daily Timer after its setting is done
1
Press CLOCK/TIMER repeatedly until
C::_=:_,._e_°eE[
"DAILY"
appears on the display.
The DAILY (Daily Timer) indicator starts flashing on the display and @ (Timer)
indicator remains lit.
2
To turn off the Daily Timer, press
CANCEL/DEMO.
...........
The DAILY (Daily Timer) and @ (Timer)
indicators go off from the display ("DAILY
OFF" appears for a while).
The Daily Timer is canceled, but the setting for the Daily
Timer remains in memory.
Or
To turn on the Daily Timer, press
SET/DISPLAY.
"OK J" appears on the display for 2 seconds.
The settings you have done are shown on the display in sequence for your confirmation.
SET/
DISPLAY
% r VOLUME -"'--_ VOLUME 5 _
_,..-VOLUME 15 _ VOLUME 10
--I
.........
• If you select "VOLUME - -," the volume is set to the last level when the unit has been turned off.
- 27 -
UsingRecordingTimer
With Recording Timer, you can make a tape of a radio broadcast automatically.
How RecordingTimer actuallyworks
The unit automatically turns on, tunes in to the specified station, sets the volume level to "VOLUME MIN," and starts recording when the on-time comes ("REC" and the REC indicator flash just before the on-time, and the REC indicator continues flashing while the timer is operating). Then, when the off-time comes CREC OFF" flashes just before the offtime), the unit automatically turns off (on standby).
The timer setting remains in memory until you change it.
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.
• To correct a misentry while setting the timer, press
CANCEL/DEMO.
On the unit ONLY:
1
Insert a recordable cassette with the exposed part of the tape down.
2
Press CLOCK/TIMER repeatedly
until "REC"
_o_
appears on the display.
The @ (Timer) indicator lights up and the REC
(Recording Timer) indicator also starts flashing on the display.
• Each time you press the button, the timer setting modes change as follows:
4
Set the on-time you want the unit to turn on at.
1) Turn _ / _ to set the hour, then press SET/DISPLAY.
"SET" appears for 1 second.
2) Turn _ / _ to set the minute, then press SET/DISPLAY.
"SET" appears for 1 second, then the unit enters off-time setting mode.
Continued I_
SET/
DISPLAY
::iti_?
n n
;J
5
Set the off-time you want the unit to turn off
(on standby)
at.
1) Turn _ / _ to set the hour, then press
SET/DISPLAY.
"SET" appears for 1 second.
2) Turn _ / _ to set the minute, then press
SET/DISPLAY.
"SET" appears for 1 second, then the unit enters preset station selecting mode.
6 Select the preset station.
1) Turn _ / _ to select the band ("TUNER FM" or
"TUNER AM"), then press SET/DISPLAY.
"SET" appears for 1 second.
2) Turn _ / _ to select a preset channel number,
then press SET/DISPLAY.
The REC (Recording Timer) indicator stops flashing
and remains lit. "OK V'" appears on the display for
2 seconds.
The settings you have done are shown on the display
in sequence for your confirmation.
(Daily Timer setting)
DALLY--TIMER
Canceled -.,-- Clock _ TIMER setting
(Recording Timer setting)
(The hour digits start flashing.)
3
Press CLOCK/TIMER again.
"TIMER" appears for 2 seconds, then the
unit enters on-time setting mode. n ,,,
I-I I _1 n
7 Press Oil to turn off the unit (on
standby) if necessary.
•
If you want to listen to another source while recording
PressREC START/STOPor • to stop recording.
Without
stopping
it, you cannot change
the source.
• Even if you unplug the AC power cord or if a power failure occurs
Once you set the timer, the timer setting may remain stored in memory for a few days.
In this case, check whether the timer setting still remains or not.
- 28 -
To turn on or off Recording Timer after its setting is done
1
Press CLOCK/TIMER repeatedly until
C:_°u[[
"REC"
appears on the display.
The REC (Recording Timer) indicator starts flashing on the display and the @ (Timer)
indicator remains
lit.
2 To
turn off the Recording
Timer, press
CANCEL/DEMO.
...........
The REC (Recording Timer) indicator goes off from the display ("REC OFF" appears on the display for 2 seconds).
The Recording Timer is canceled, but the setting for the
Recording Timer remains in memory.
Or
To turn on the Recording Timer, press
SET/DISPLAY.
"OK J" appears on the display for 2 seconds.
The settings you have done are shown on the display in sequence for your confirmation.
SET /
DISPLAY
%
To check the remaining time until the shut-off
time, press
SLEEP once so that the remaining time (minute) until the shut-off time appears for about 5 seconds.
To change the shut-off time, press SLEEP repeatedly
until
the desired time length appears on the display.
To cancel the setting, press SLEEP repeatedly so that the
SLEEP indicator goes off.
• Sleep Timer is also canceled when you turn off the unit.
Timer Priority
Since each timer can be set separately, you may wonder what happens if the settings for these timers overlap.
Below are some examples.
Recording Timer has priority over Daily Timer and Sleep Timer.
• If Daily Timer is set to come on while Recording Timer is operating, Daily Timer will not come on at all.
Recording Timer
Daily Timer
6:00
I
[
I i,
6:30
I
I
7:00
]
I
I
7:30
I
I
UsingSleep Timer
With Sleep Timer, you can fall asleep to music. You can set
Sleep Timer only while the unit is turned on.
• If Recording Timer is set to come on while Sleep Timer is operating, Sleep Timer will be canceled.
Recording Timer
Sleep Timer
21:00
I
I
_
[
'.
21:30
I
I
II/L_i
22:00
I
]
I
2
i
22:30
I
I
II
HowSleep Timer actuallyworks
The unit automatically turns off after the specified time length passes.
On the remote control ONLY:
1
Press
SLEEP.
_-_
The time length until the shut-off time appears and the SLEEP indicator starts flashing on the display.
• Each time you press the button, the time length changes as follows:
SLEEP 10"--SLEEP 20"-"-SLEEP 30"-- SLEEP 601
Canceled -.,,--SLEEP 120 -.',- SLEEP 90
• If the built-in clock has not been set, "CLOCK ADJUST" appears on the display.
2
Wait for about 5 seconds
after specifying
the
time length.
The SLEEP indicator stops flashing and remains
lit.
- 29 -
Maintenance
To get the best performance of the unit, keep your discs, tapes, and mechanism clean.
General Notes
In general, you will have the best performance by keeping your discs and the mechanism clean.
• Store discs in their cases, and keep them in cabinets or on shelves.
• Keep the unit's disc trays closed when not in use.
Handlingcassettetapes
• If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels and rotating.
• If the tape is loose, it may get stretched, cut, or caught in the cassette.
• Be careful not to touch the tape surface.
Handling discs
• Remove the disc from its case by holding it at the edge while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the disc.
• Put the disc back in its case after use to prevent warping.
Avoid the following places to store the tape:
-- In dusty places
-- In direct sunlight or heat
-- In moist areas
-- Near a magnet x@ xQ
• Be careful not to scratch the surface of the disc when placing it back in its case.
• Avoid exposure to direct sunlight, temperature extremes, and moisture.
To clean the disc
Wipe the disc with a soft cloth in a straight line from center to edge.
Continued use of irregular shape discs
(heart-shape, octagonal, etc.) can damage the unit.
Cleaningthe unit
• Stains on the unit
Should be wiped off with a soft cloth. If the unit is heavily stained, wipe it with a cloth soaked in water diluted neutral detergent and wrung well, then wipe clean with a dry cloth.
• Since the unit may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the following.
-DO NOT wipe it with a hard cloth.
-DO NOT wipe it strong.
-DO NOT wipe it with thinner or benzine.
-DO NOT apply any volatile substance such as insecticides to it.
-DO NOT allow any rubber or plastic to remain in contact with it for a long time.
/
._
DO NOT use any solvent--such as conventional the disc.
-30-
Troubleshooting
If you are having a problem with your unit, check this list for a possible solution before calling for service.
If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person, such as your dealer, for service.
[,."]Nlilg_il
Unable to cancel the demonstration.
Press CANCEL/DEMO
(See page 8.) on the unit.
No sound is heard.
z
,,,,,a
'_ Operations are disabled.
__
Unable to operate the unit from the remote control.
Stereo effect is lost.
The built-in microprocessor may malfunction due to external electrical interference.
• The path between the remote control and the remote sensor on the unit is blocked.
• The batteries are exhausted.
Vocal Masking is activated.
• Antennas are disconnected.
because of noise.
Hard to listen to broadcasts
The disc tray does not open or close.
The disc sound is discontinuous.
The disc does not play.
The disc does not play.
The disc readout time is too long.
• The AM loop antenna is too close to the unit.
• The FM antenna is not properly extended and positioned.
The disc is scratched or dirty.
• The AC power cord is not plugged in.
• Trays are locked.
The disc is placed upside down.
• No MP3 files are recorded on the disc.
• MP3 files do not have the file extension--.MP3, .Mp3, .mP3, or
.mp3 in their file names.
• MP3 files are not recorded in the format compliant with ISO 9660
Level 1 or Level 2.
The readout time varies with the complexity of the recording configuration.
Check all connections and make corrections. (See pages 6 to 8.)
Unplug the AC power cord and then plug it back in.
• Remove the obstruction.
• Replace the batteries.
Cancel the Vocal Masking. (See page 25.)
•
Reconnect the antennas correctly and securely.
• Change the position and direction of the AM loop antenna.
• Extend the FM antenna at the best position.
Clean or replace the disc. (See page 30.)
• Plug the AC power cord.
• Unlock the trays.
(See page 20.)
Place the disc with the label side up.
Replace the disc.
Do not use too many hierarchies and directories when recording. Also, do not record any other types of audio tracks together with MP3 files.
(See page 15.)
Turn on the unit.
opened.
The cassette holders cannot be
_ Impossible to record.
E@'alle4'_
The button other than CANCEL/DEMO is pressed to cancel the demonstration temporarily.
Connections are incorrect or loose.
Power supply from the AC power cord has been cut off while the tape was running.
Small tabs on the back of the cassette are removed.
Cover the holes with adhesive tape.
(See page 22.)
-31 -
Specifications
Amplifier section
Output Power (IEC 268-3)
SUBWOOFERS: 100 W per channel, min.
RMS, both channels driven into 6 _ at 63 Hz with no more than 0.9% total harmonic distortion.
MAIN SPEAKERS: 30 W per channel, min. RMS, both channels driven into 6 _ at 1 kHz with no more than 0.9% total harmonic distortion.
Audio input sensitivity/Impedance
(Measured at 1 kHz, with tape recording signal 300 mV)
AUX: 390 mV/50 kfl
MIX 1/2: 1.5 mV/5 kfl
Digital output: CD OPTICAL DIGITAL OUTPUT
Signal wave length: 660 nm
Output level: -15 dBm to -12 dBm
Speakers!Impedance:
SUBWOOFERS:
MAIN SPEAKERS:
6 _ - 16
6 _ - 16
Tuner
FM tuning range:
AM tuning range:
87.50 MHz - 108.00
MHz
At 9 kHz intervals:
At 10 kHz intervals:
531 kHz - 1 710 kHz
530 kHz - 1 710 kHz
CD player
CD capacity:
Dynamic range:
Signal-to-noise
Wow and flutter: ratio:
MP3 recording format:
Max.
Bit rate:
3 CDs
85 dB
90 dB
Immeasurable
MPEG 1/2 Audio Layer 3
320 kbps
Cassettedeck
Frequency response
Normal (type I): 50 Hz - 14 000 Hz
Wow and flutter: 0.15% (WRMS)
General
Power requirement:
Power consumption:
Dimensions (approx.):
Mass (approx.):
AC ll0V/AC 127 V/AC 220V/
AC 230 V - AC 240 V r_ (adjustable with the voltage selector), 50 Hz ! 60 Hz
200 W (in operation)
29 W (on standby with Ecology Mode off)
Less than 3.5 W (on standby with
Ecology Mode on)
205 mm x 370 mm x 370 mm (W/HID)
10.0 kg
Suppliedaccessories
See page 6.
Design
and specifications
are subject to change without notice.
-32-
MEMO
MEMO
Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada,
Australia, and U.K.)
Instruccibn sobre la linea de la red (CA) (no aplicable para Europa, EE.UU.,
Canadd, Australia, ni el Gr_-Bretanha)
Instru_o sobre a tens_o da rede eldctrica (CA) (n_o aplicdvel para a Europa, os E.U.A., o Canadd, a Austrdlia e o Reino Unido)
VOLTAGE
SELECTOR
1
@EN, SP, PR
IMPORTANT for mains (AC) line
BEFORE PLUGGING IN, do check that your mains (AC) line voltage corresponds with the position of the voltage selector switch provided on the outside of this equipment and, if different, reset the voltage selector switch, to prevent from damage or risk of fire/electric shock.
IMPORTANTEpara la linea de la red (CA)
ANTES DE ENCHUFAR EL EQUIPO, compruebe si la tensi6n de la linea de la red (CA) corresponde con la posici6n del selector de tensi6n situado en la parte exterior del equipo, y si es diferente, reajuste el selector de tensi6n para evitar el riesgo de incendios/descargas el_ctricas.
IMPORTANTEpara a liga_o _ tens_o da rede (CA)
ANTES DE LIGAR O APARELHO A UMA TOMADA DA
REDE, verifique sea tensgo da rede CA corresponde b posiqgo do seletor de voltagem localizado na parte externa deste equipamento.
Caso ngo corresponda, reajuste o seletor de voltagem a tim de evitar avarias ou riscos de inc_ndio e choque el_trico.
VICTOR COMPANY OF JAPAN, LIMITED
@
_) 0602MWMMDWJEM
advertisement
Related manuals
advertisement