TOTAL ACCESS 750 QUAD FXS/FXO

QUAD FXS

L1 CLEI: SIC2WXOK_ _

L2 CLEI: SIC2WXHK_ _

TURN UP STEPS

1 Insert card into slots 1-6 on the TA 750. The unit will automatically map

DS0s in the T1 as noted below.

TIME SLOT ASSIGNMENT

Physical Slot T1 Time Slot Assigned

3

4

1

2

5

6

1-4

5-8

9-12

13-16

17-20

21-24

QUAD FXO

L1 CLEI: SIC2VXOK_ _

L2 CLEI: SIC2VXHK_ _

2

Verify LED sequencing. LEDs will stop sequencing once unit is initialized.

Note: If the unit is inserted into a physical slot which has its timeslots allocated to the FT1

(DSX-1) or Nx56/64 port, the LEDs will sequence continually, indicating a problem.

The time slots must be freed up using the menu interface before the unit will become operational.

STATUS LEDS (GREEN)

●

OFF

✸

FLASHING

●

ON

●

●

On Hook

Ringing (FXS only)

Off Hook (Busy)

●

SEQUENCING All Four Time Slots Unavailable

●

●

●

3

If factory default settings to be used for the application, then installation is complete. If further provisioning is desired proceed to step 4.

FACTORY DEFAULT SETTINGS

The FXS unit has factory default provisioning: FXS mode, loop start signaling and automatic loop provisioning. The automatic loop provisioning function will automatically set the line impedance and gain after the first off hook event.

The FXO factory default settings are FXO mode and loop start signaling.

If different settings are desired, the VT 100 terminal interface is used.

JOB A ID

61175408L2-22B

0006

4

Connect VT 100 compatible terminal to BCU faceplate ADMIN port

4a Connect DB-9 cable

4b Run terminal emulation program

Craft Port Settings are as follows: 9600 Baud, No parity, 8 data bits, 1 Stop bit, No flow control.

4c If using Windows Hyperteminal open by selecting

Programs/Accessories/Hyperterminal

Note: To ensure proper display background, select VT 100 Terminal Emulation under Settings.

5

Proceed through menus to desired access module

5a select Access Modules

5b select 1-6 (slot)

5c select 1-4 (circuit)

Note: To traverse through the menus, select the desired entry and press Enter. To work back-

wards in the menu press ESC (escape key). To return to the top of the menu at any time, press the return key twice.

6

Change port provisioning for a particular application.

Note: Provisioning for a port can be copied to another port or to all similar ports.

7

Testing - to access the test menu for an access module select test (item 4 after 5c)

TESTING

Self Test

■ Performed when the Quad FXS or FX0 is inserted into an active chassis to verify proper operation of critical circuits.

Initiated Tests

■ Digital Loopback Test – loops back DS0 data coming from the network for each individual channel.

■ Network On-Hook / Off-Hook Test – tests signaling sent to the network by the unit.

■ Customer Ring Test (FXS only) – activates the unit’s ring relay in a 2-on /

4-off ring cadence, providing ringing to the customer loop.

■ 1000 Hz DRS Tone Generation Test – sends DRS signal on the receive path to the loop and transmit path towards Carrier.

Note: All tests except self test are initiated through the TA 750 BCU Admin Port, TA 850

RCU, or TA 1500 SCU.

Note: The Quad FXS is for use in the TA 750 and the TA 850.

The Quad FX0 is for use in the TA 750, the TA 850, and the TA 1500.

Note: The 1175408L2 is completely interchangeable with the 1175408L1.

The 1175407L2 is completely interchangeable with the 1175407L1.

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

■

■

For a complete Quad FXS I&M Practice: 877.457.5007, Document # 484. Please have your fax number available.

■

For a complete Quad FX0 I&M Practice: 877.457.5007, Document # 485. Please have your fax number available.

■

Switch

Switch

DS1

Data Switch

Switch

GR303 DS1

GR303 Access

Concentrator

DCS

TDM

TOTAL ACCESS 750 QUAD FXS/FXO

CONNECTIONS

■ All connections are made through the 50-pin amphenol connector on the back panel

TA 750/850/1500.

ELECTRICAL CODE COMPLIANCE

The Quad FXS and Quad FXO are to be installed in restricted access locations and in equipment with a Type “B” or “E” installation code.

Code Input Output

IC

TC

PC

A

–

C

–

X

C

APPLICATIONS

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by ADTRAN could void the user’s authority to operate this equipment.

Router

PRICING AND AVAILABILTY 800.827.0807

TECHNICAL SUPPORT 888-4ADTRAN

RETURN FOR REPAIR 256.963.8722

www.adtran.com

MODES OF OPERATION

Note: Signaling states are provisioned through the BCU.

FXS

■

■

■

■

■

FXS Loop Start (default)

■

FXS Ground Start

TR-08 Single Party

TR-08 Universal Voice Grade

DPO

Tandem (E & M)

FXO

■

FXO Loop Start (default)

■

FXO Ground Start

■ DPT

ATTENUATION LEVELS

0 dB to -9 dB

FXS

■

■

Short loop default: -6 dB Transmit, –3 dB Receive

Long loop default: -3 dB Transmit, –3 dB Receive

FXO

■

Default 0 dB Transmit, 0 dB Receive

IMPEDANCE SETTINGS

FXS

600 Ω

900

Ω

600 Ω + 2.16 µF (short loop default)

900

Ω + 2.16 µF (long loop default)

FXO

900 Ω + 2.16 µF

WARRANTY

Warranty for Carrier Networks products manufactured by ADTRAN and supplied under

Buyer's order for use in the U.S. is ten (10) years. For a complete copy of ADTRAN's U.S.

Carrier Networks Equipment Warranty: (877) 457-5007, Document 414.