advertisement
Leica DISTO
TM
D1
The original laser distance meter
Overview
Technical data
Instrument Set-up
Operations
Message Codes
Care
Warranty
Safety instructions
Leica DISTO™ D1
1
Overview
Ov e rv ie w
The Leica DISTO™ is a laser distance meter oper-
ating with a class 2 laser. See chapter Technical data for scope of use.
1 Display
Leica DISTO™ D1
2
Technical data
T e c h n ic a ld a ta
General
Accuracy with favourable conditions *
Accuracy with unfavourable conditions **
Range with favourable conditions *
Range with unfavourable conditions **
Smallest unit displayed
Laser class
Laser type
ø laser point | at distances
Protection class
Auto. laser switch off
Auto. power switch off
Bluetooth® Smart
Range of Bluetooth® Smart
Battery durability (2 x AAA)
Dimension (H x D x W)
Weight (with batteries)
Temperature range Storage | Operation
2 mm / 0.08 in ***
3 mm / 1/8" ***
0.2 - 40 m / 0.6 - 120 ft ***
0.2 - 30 m / 0.6 - 100 ft ***
0.1 mm / 1/32 in
2
635 nm, <1 mW
6 /30 /60 mm | 10/ 50/ 100 m
IP54 (dust- and splash water protected) after 90 s after 180 s
Bluetooth® v4.0
<10m up to 10000 measurements
115 x 43.5 x 23.5 mm | 4.53 x 1.71 x 0.93 in
87 g/ 3.07 oz
-25 to 70°C/ -13 to 158°F | -0 to 40°C/ 32 to 104°F
* favourable conditions are: white and diffuse reflecting target (white painted wall), low background illumination and moderate temperatures.
** unfavourable conditions are: targets with lower or higher reflectivity or high background illumination or temperatures at the upper or lower end of the specified temperature range.
*** Tolerances apply from 0.05 m to 5 m with a confidence level of 95%.
With favourable conditions the tolerance may deteriorate by 0.10 mm/m for distances above 5 m.
With unfavourable conditions the tolerance may deteriorate by 0.15 mm/m for distances above 5 m.
Leica DISTO™ D1
3
Technical data
Functions
Distance measuring
Permanent measuring
Beep
Illuminated display
Bluetooth® Smart yes yes yes yes yes
Leica DISTO™ D1
4
Instrument Set-up
In s tru me n tSe t-u p
Introduction
The safety instructions (see Safety
Instructions) and the user manual
should be read through carefully before the product is used for the first time.
The person responsible for the product must ensure that all users understand these directions and adhere to them.
The symbols used have the following meanings:
WARNING
Indicates a potentially hazardous situation or an unintended use which, if not avoided, will result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor injury and/or appreciable material, financial and environmental damage.
Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner.
Leica DISTO™ D1
5
Instrument Set-up
Insert batteries
To ensure a reliable use, we recommend using high quality Alkaline batteries. Change batteries when battery symbol is flashing.
Leica DISTO™ D1
6
Instrument Set-up
Switching ON/OFF
Device is turned OFF.
Leica DISTO™ D1
7
Instrument Set-up
Clear
Undo last action.
Leave actual function, go to default operation mode.
Leica DISTO™ D1
8
Instrument Set-up
Message Codes
If the message "i" appears with a number, observe the instruc-
tions in Message Codes section.
Example:
Leica DISTO™ D1
9
Instrument Set-up
Settings
Press both keys simultaneousley.
Leica DISTO™ D1
Switch between the following units:
0.000 m
0'00" 1/16
0.0000 m
0.000 in
0.00 ft
0 in 1/16
10
Operations
Op e ra tio n s
Measuring single distance
Aim active laser at target.
Target surfaces: Measuring errors can occur when measuring to colourless liquids, glass, styrofoam or permeable surfaces or when aiming at high gloss surfaces. Against dark surfaces the measuring time increases.
Leica DISTO™ D1
11
Operations
Permanent measuring
The last value measured is displayed in the main line.
Stops permanent measuring.
Leica DISTO™ D1
12
Operations
Bluetooth® Smart
DISTO™ sketch. Use App for
Bluetooth® data transfer.
Bluetooth® Smart is always active when the device is switched on. Connect the device with your smart-phone, tablet, laptop.. Measurement values will be transferred automatically right after a measurement. The efficient and innovative
Bluetooth® Smart module (with the new Bluetooth® standard
V4.0) works together with all
Bluetooth® Smart Ready devices. All other Bluetooth® devices do not support the energy saving Bluetooth®
Smart Module, which is integrated in the device.
We provide no warranty for free
DISTO™ software and offer no support for it. We accept no liability whatsoever arising from the use of the free software and we are not obliged to provide corrections nor to develop upgrades. A wide range of commercial software can be found on our homepage. Apps for
Android® or iOS can be found in special internet shops. For more details, see our homepage.
Leica DISTO™ D1
13
Message Codes
Me s s a g e Co d e s
No.
Cause
253
255
256
257
204
220
240
252
Calculation error
Hardware error
Data transfer error
Temperature too high
Temperature too low
Received signal too weak, measuring time too long
Received signal too high
Too much background light
Correction
Perform measurement again.
Contact your dealer
Connect device and repeat procedure
Let device cool down.
Warm device up.
Change target surface (e.g. white paper).
Change target surface (e.g. white paper) .
Shadow target area.
* If other message codes are displayed frequently even the instrument has been switched off and on, please contact your dealer.
Leica DISTO™ D1
14
Ca re
Care
l l l
Clean the device with a damp, soft cloth.
Never immerse the device in water.
Never use aggressive cleaning agents or solvents.
Leica DISTO™ D1
15
Warranty
Wa rra n ty
Warranty under PROTECT by Leica
Geosystems
Lifetime Manufacturer´s Warranty
Warranty coverage for the entire usage time of the product under PROTECT according to Leica
Geosystems International Limited Warranty and
PROTECT General Terms & Conditions set out under www.leica-geosystems.com. Free of charge repair or replacement of all products or any parts under PROTECT that suffer defects as a result of faults in materials or workmanship.
3 Years No Cost
Additional services should the product under
PROTECT become defective and require servicing under normal conditions of use, as described in the user manual, at no additional charge.
To receive the "3 Years No Cost" period, the product under PROTECT must be registered at myworld.leica-geosystems.com within 8 weeks of the purchase date. If the product under
PROTECT is not registered, a "2 years No Cost" period applies.
Leica DISTO™ D1
16
Safety instructions
Sa fe ty in s tru c tio n s
The person responsible for the instrument must ensure that all users understand these directions and adhere to them.
Leica DISTO™ D1
17
Safety instructions
Symbols used
The symbols used have the following meanings:
WARNING
Indicates a potentially hazardous situation or an unintended use which, if not avoided, will result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor injury and/or appreciable material, financial and environmental damage.
Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner.
Leica DISTO™ D1
18
Safety instructions
Permitted use
l l
Measuring distances
Data transfer with Bluetooth®
Leica DISTO™ D1
19
Safety instructions
Prohibited use
l l l l l l l l l l
Using the product without instruction
Using outside the stated limits
Deactivation of safety systems and removal of explanatory and hazard labels
Opening of the equipment by using tools
(screwdrivers, etc.)
Use of accessories from other manufacturers without express approval
Carrying out modification or conversion of the product
Deliberate dazzling of third parties; also in the dark
Inadequate safeguards at the surveying site (e.g. when measuring on roads, construction sites, etc.)
Deliberate or irresponsible behaviour on scaffolding, when using ladders, when measuring near machines which are running or near parts of machines or installations which are unprotected
Aiming directly in the sun
Leica DISTO™ D1
20
Safety instructions
Hazards in use
WARNING
Watch out for erroneous measurements if the instrument is defective or if it has been dropped or has been misused or modified. Carry out periodic test measurements. Particularly after the instrument has been subject to abnormal use, and before, during and after important measurements.
CAUTION
Never attempt to repair the product yourself. In case of damage, contact a local dealer.
WARNING
Changes or modifications not expressly approved could void the user´s authority to operate the equipment.
Leica DISTO™ D1
21
Safety instructions
Limits of use
Refer to section Technical data. The device
is designed for use in areas permanently habitable by humans. Do not use the product in explosion hazardous areas or in aggressive environments.
Leica DISTO™ D1
22
Safety instructions
Areas of responsibility
Responsibilities of the manufacturer of the original equipment:
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Internet: www.leica-geosystems.com
The company above is responsible for supplying the product, including the User Manual in a completely safe condition.
The company above is not responsible for third party accessories.
Responsibilities of the person in charge of the instrument: l l l
To understand the safety instructions on the product and the instructions in the
User Manual.
To be familiar with local safety regulations relating to accident prevention.
Always prevent access to the product by unauthorised personnel.
Leica DISTO™ D1
23
Safety instructions
Disposal
CAUTION
Flat batteries must not be disposed of with household waste. Care for the environment and take them to the collection points provided in accordance with national or local regulations.
The product must not be disposed with household waste. Dispose of the product appropriately in accordance with the national regulations in force in your country. Adhere to the national and country specific regulations.
Product specific treatment and waste management can be downloaded from our homepage.
Leica DISTO™ D1
24
Safety instructions
Electromagnetic Compatibility
(EMC)
WARNING
The device conforms to the most stringent requirements of the relevant standards and regulations.
However, the possibility of causing interference in other devices cannot be totally excluded.
Japanese Radio Law Compliance
This device is granted pursuant to the Japanese
Radio Law 電 波 法 . This device should not be modified otherwise the granted designation number will become invalid.
Leica DISTO™ D1
25
Safety instructions
FCC statement (applicable in U.S.)
This equipment has been tested and found to comply with the limits for a Class B digital instrument, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: l l l l
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subjected to the following two conditions: l
This device may not cause harmful interference, and l this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement
The radiated rf output power of the instrument is below the FCC radio frequency exposure limits for portable devices according to KDB 447498.
Leica DISTO™ D1
26
Safety instructions
ISED Statement (applicable in
Canada)
This device complies with Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions: l l
This device may not cause harmful interference, and this device must accept any interference, including interference that may cause undesired operation of the device.
Radio Frequency (RF) Exposure Compliance
Statement
The radiated rf output power of the instrument is below the Health Canada's Safety Code 6 exclusion limit for portable devices (radiated element separation distance between the radiating element and user and/or bystander is below 20 cm).
Leica DISTO™ D1
27
Safety instructions
Use of the product with Bluetooth®
WARNING
Electromagnetic radiation can cause disturbances in other equipment, in installations (e.g. medical ones such as pacemakers or hearing aids) and in aircraft. It can also affect humans and animals.
Precautions:
Although this product conforms to the most stringent standards and regulations, the possibility of harm to people and animals cannot be totally excluded.
l l l l
Do not use the product near petrol stations, chemical plants, in areas with a potentially explosive atmosphere and where blasting takes place.
Do not use the product near medical equipment.
Do not use the product in airplanes.
Do not use the product near your body for extended periods.
Leica DISTO™ D1
28
Safety instructions
Laser classification
The device produces visible laser beams, which are emitted from the instrument: It is a Class 2 laser product in accordance with: l
IEC60825-1 : 2014 „Radiation safety of laser products“
Pulse duration
> 400 ps
Pulse repetition frequency
320 MHz
Beam divergence
0.16 x 0.6 mrad
Laser Class 2 products:
Do not stare into the laser beam or direct it towards other people unnecessarily. Eye protection is normally afforded by aversion responses including the blink reflex.
WARNING
Looking directly into the beam with optical aids
(e.g. binoculars, telescopes) can be hazardous.
CAUTION
Looking into the laser beam may be hazardous to the eyes.
Wavelength
620 - 690 nm
Maximum radiant output power for classification
< 1 mW
Leica DISTO™ D1
29
Safety instructions
Labelling
Subject to change (drawings, descriptions and technical data) without prior notice.
Leica DISTO™ D1
30
advertisement