advertisement
Infortrend Hardware Manual
EonNAS Pro Series
Eon NAS
P ro
SELECT
ENTER
Eon NAS
Pro
SELECT
ENTER
E onNAS
P ro
B A C K U P
Version 1.5
Contact Information
Contact Information
Customer Support
Contact your system vendor or visit the following support sites.
EonStor DS Support
ESVA Support
EonNAS Support
Headquarters
(Taiwan)
Infortrend Technology, Inc.
8F, No. 102, Sec. 3, Jhongshan Rd., Jhonghe Dist., New Taipei City 235, Taiwan
Tel: +886-2-2226-0126 Fax: +886-2-2226-0020 Email , Technical Support , Website
Japan Infortrend Japan, Inc.
6F Okayasu Bldg., 1-7-14 Shibaura, Minato-Ku, Tokyo, 105-0023 Japan
Tel: +81-3-5730-6551 Fax: +81-3-5730-6552 Email , Technical Support , Website
China
Europe (EMEA)
2200 Zanker Road, Suite 130, San Jose, CA. 95131, USA
Tel: +1-408-988-5088 Fax: +1-408-988-6288 Email , Technical Support , Website
US East Coast Office
4 Northeastern Blvd. Suite 21B, Nashua, NH, 03062, USA
Tel: +1-603-610-6398 Fax: +1-603-610-6383 Email , Technical Support , Website
Infortrend Technology, Ltd.
Room 1210, West Wing, Tower One, Junefield Plaza No.6 Xuanwumen Street,
Xuanwu District, Beijing, China
Tel: +86-10-6310-6168 Fax: +86-10-6310-6188 Email , Technical Support , Website
Infortrend Europe LTD.
1 Cherrywood, Stag Oak Lane Chineham Business Park Basingstoke, Hampshire
RG24 8WF, UK
Tel: +44-1256-707-700 Fax: +44-1256-707-889 Email , Technical Support , Website
Germany/ Infortrend Deutschland GmbH
Wappenhalle Business Center Konrad-Zuse-Platz 8, 81829 Munich, Germany
Tel: +49-89-2070-42650 Fax: +49-89-2070-42654 Email , Technical Support , Website
Legal Information
Legal Information
All Infortrend products, including the product customers have purchased from
Infortrend, shall be subject to the latest Standard Warranty Policy available on the
Infortrend website: http://www.infortrend.com/global/Support/Warranty
Infortrend may from time to time modify, update or upgrade the software, firmware or any accompanying user documentation without any prior notice. Infortrend will provide access to these new software, firmware or documentation releases from certain download sections of our website or through our service partners. Customer shall be responsible for maintaining updated version of the software, firmware or other documentation by downloading or obtaining from Infortrend, and installing designated updated code, including but not limited to firmware, microcode, basic input/out system code, utility programs, device drivers, and diagnostics delivered with Infortrend product.
Before installing any software, applications or components provided by a third party, customer should ensure that they are compatible and interoperable with Infortrend product by checking in advance with Infortrend. Customer is solely responsible for ensuring the compatibility and interoperability of the third party’s products with
Infortrend product. Customer is further solely responsible for ensuring its systems, software, and data are adequately backed up as a precaution against possible failures, alternation, or loss.
For any questions of hardware/ software compatibility, and the update/ upgrade code, customer should contact Infortrend sales representative or technical support for assistance. To the extent permitted by applicable laws, Infortrend shall NOT be responsible for any interoperability or compatibility issues that may arise when (1) products, software, or options not certified and supported by Infortrend are used; (2) configurations not certified and supported by Infortrend are used; (3) parts intended for one system are installed in another system of different make or model.
Disclaimer
Trademarks
Copyright Notice
Copyright Notice
All rights reserved. This publication may not be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written consent of Infortrend
Technology, Inc.
Infortrend Technology makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.
Furthermore, Infortrend Technology reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation to notify any person of such revisions or changes. Product specifications are also subject to change without prior notice.
Infortrend, the Infortrend logo, SANWatch, ESVA, EonStor, EonStor
DS, EonNAS, and EonPath are registered trademarks of Infortrend
Technology, Inc. Other names prefixed with “IFT” and “ES” are trademarks of Infortrend Technology, Inc.
Windows is a registered trademark of Microsoft Corporation.
Mac OS X is a registered trademark of Apple Computer, Inc.
Linux is a trademark of Linus Torvalds.
All other names, brands, products or services are trademarks or registered trademarks of their respective owners.
Precautions
Safety Precautions
Read these instructions before you install, operate, or transport the system.
Setup the system at a site where the ambient temperature stays lower than 40
C.
Install the power source socket outlet near the enclosure where it is easily accessible.
Secure airflow clearance around the enclosure
:
- Secure an 18 to 20cm clearance around the enclosure.
- Do not cover the enclosure openings.
- Do not leave the drive bays empty as it will affect the airflow efficiency.
NEVER
remove more than one hard disk drive tray out of the enclosure at the same time!
Secure
each hard disk drive using its retaining screws.
Put the power cords
and other cables away from foot traffic. Do not place things over the power cords and make sure they do not rest against data cables.
Ensure that the correct power range
is being used before powering the device.
If the enclosure is not used for a long time, disconnect it from mains to avoid transient over-voltage.
ESD Precautions
Avoid touching the PCB boards or connector pins on the hard drives.
Avoid dust, debris, carpets, plastic, vinyl, and tyrofoam in your work area.
Do not remove the hard disk drive from its anti-static bag before installation takes place.
Hard drives must not be stacked on top of each other without their protective drive trays. Even when drives are fixed in the drive trays, contacting the exposed PCB or rear-side connector interface may damage the hard drives.
Component Compatibility
The use of compatible components is strongly recommended to ensure compatibility, quality and normal operation with your system. Please contact your vendor for a list of compatible components.
Service and Maintenance
Service and Maintenance
Keep the faulty hard disk drive in place until you have a replacement unit in hand; removing a hard disk drive tray will affect airflow within the enclosure.
When transporting the enclosure, repackage all disk drives separately in the original package foam blocks.
Disconnect the power cords before servicing or cleaning the enclosure.
Use a slightly moistened paper sheet or cloth for cleaning. Avoid using liquid or sprayed detergent.
When replacing hard drives, insert the hard drive cage as gently as possible while assuring full engagement. Vibration and shock can easily damage hard drives.
Contact service personnel if any of the following situations occurs:
- The power cord or plug is damaged.
- The enclosure has been exposed to moisture.
- The system has not been working properly.
- The enclosure was dropped against a hard surface.
- The enclosure shows obvious signs of breakage.
When relocating the enclosure, hard drives should be removed from the enclosure beforehand.
Please remember the installation order of the hard disk drive and their corresponding slots.
About This Manual
About This Manual
This manual introduces the hardware components of EonNAS Pro NAS systems and describe how to install, operate and maintain them.
For the following subjects, please consult other resources for more information:
Components that are not user-serviceable: Contact our support sites.
Software operation: Consult the User Manual in the CD-ROM.
Revision History
Version Date Description
1.0 December, 2011 Initial release
Updated LCD power saving functions
Updated support of single hard drive for initialization
Merged EonNAS Pro 200, 500, 800 & 850 series into
EonNAS_Pro_Series_HMN.
Updated component compatibility notice
1.3 June,
1.4 August, 2012 Updated 10Gb iSCSI descriptions
1.5 December, 2012 Added EonNAS Pro 210, 510 & 810
Table of Contents
Table of Contents
9
EonNAS Pro Series Hardware Manual
Introduction
The Network Attached Storage (NAS) systems are high-performance and versatile storage solutions for sharing files and volumes across the Ethernet network. NAS separates application servers and data, and stores data on storage devices that perform dedicated file serving tasks. They are dedicated high-performance storage solutions providing files or shares for access from numerous clients. The advantages include:
Ease of administration
Ease of installation
Ease of capacity expansion
Compact in size for mobility and ease of placement
The ability to serve a common set of files to a heterogeneous client population
Improved performance based upon dedicated file service processing
1Gb / 10 Gb iSCSI expansion host ports for extended connectivity (selected models only)
10
EonNAS Pro Series Hardware Manual
Front Panel Overview
The systems are ruggedly built and come in two (2), five (5) and eight (8) hard drive bay variations. The hard drive bay supports a single 3.5 inch SATA hard drive up to
3TB in storage capacity. Systems may come with or without a LCD screen for status display and quick configuration purposes. All systems also feature a quick USB backup port on the front panel.
SE LECT
E N TE R
SE LE CT
E NT E R
BACKUP
Features
LCD screen for quick function access and status monitoring (selected models only)
Single hard drive support up to 3TB
Hot swappable hard drives
Versatile miniaturized NAS storage for ease of placement or mobility
Easy to setup and operate
External eSATA / USB hard disk drive expansion
Easy to access front USB port for one-touch data backup
11
EonNAS Pro Series Hardware Manual
System Front panel
3 3 3
3
2x0 5x0
8x0
No.
2.
Item
Enter button
Description
The LCD displays system statuses and offer users quick access system menus. Once initialized, if the LCD has been left idling for more
screen
than 60 seconds, the LCD will automatically power off. Users can press the “SELECT” or “ENTER” button to reactivate the LCD screen.
The Enter button is used for making a selection while browsing system menus.
12
EonNAS Pro Series Hardware Manual
3. Select button
The Select button is used for browsing system menus.
4.
System status LED
The system status LED warns users system faults.
5.
6.
7.
8.
9.
10.
Ethernet 1 LED
Ethernet 2 LED
HDD LED
Power button
Hard drive slots
The LED indicates the status of the Ethernet 1 connection.
The LED indicates the status of the Ethernet 2 connection.
The hard drive LED indicates the status of the hard drives.
The power button is used to turn on or force-turn-off (when the system hangs).
The slots are in ascending numeric order from top to bottom.
Quick backup USB port
The quick backup USB port offers a fuss-free data backup experience.
11.
Quick backup button & LED
For use with quick USB backup port.
*Inside the front panel cover, there is a label showing the default IP addresses for the
Ethernet ports. This is useful when you
restore to default and wish to log in manually to setup
the system.
13
EonNAS Pro Series Hardware Manual
System Rear panel
EonNAS
1
2
1
2
No.
1.
210 510 / 810
Item
Power socket
Description
The power socket is for power cable connection.
The eSATA port is for external expansion purposes expansion).
14
4.
5.
6.
EonNAS Pro Series Hardware Manual
The USB ports are for external expansion purposes (CD, external eSATA devices.
Ethernet port 1 Ethernet port 1 is used for accessing and configuration.
Ethernet port 2 Ethernet port 2 is used for accessing and configuration.
Restore default button
The restore default button is for restoring the system to manufacturing settings (TCP / IP, system settings, etc.), please refer to
. The button is NOT operational during initialization.
8.
9.
10.
11.
Kensington lock-hole
For use with a Kensington lock. Please refer to your
Kensington lock for instructions.
Power adaptor
For plugging in the power adaptor.
Expansion host port location
For selected models only, expansion host port features four
1Gb iSCSI host ports or two 10Gb iSCSI host ports.
Serial COM port The serial COM port is reserved for maintenance purposes.
12.
13.
ATX power switch
USB 3.0 port
The ATX power switch acts as a secondary power switch and it must be switched to the “ON” position to power-on the system.
The USB 3.0 port differs to other USB ports in that it supports a maximum 5Gb/s transfer rate.
Additional 1Gb iSCSI Expansion Ports
For selected models that has four additional 1Gb iSCSI host ports. From left to right are CH3, CH4, CH5 and CH6 1Gb iSCSI host ports.
CH3 CH4 CH5 CH6
15
EonNAS Pro Series Hardware Manual
Additional 10Gb iSCSI Expansion Ports
For selected models that has two additional 10Gb iSCSI host ports. From left to right are CH3 and CH4 10Gb iSCSI host ports.
CH3 CH4
.
16
EonNAS Pro Series Hardware Manual
Hard Drive Designation
The hard drives are placed in numeric order from top to bottom. When installing hard drives, always install to the top empty tray(s) and work your way down in order!
2x0 5x0
8x0
17
EonNAS Pro Series Hardware Manual
Front Panel LED Definitions
1
2 3 4 5
SELECT
ENTE R
1
BACKUP
6
Systems without LCD
Front Panel LEDs
No. Item
2. System status LED
3. Ethernet 1 LED
4. Ethernet 2 LED
5. HDD status LED
6.
USB Quick Backup
LED
Systems with LCD
LED Color & Status
Blue
indicates the system has powered on
Off
indicates the system has powered off
Off
indicates the system is operating normally
Red
indicates system failure
Steady Green
indicates connection established
Blinking Green
indicates LAN activity
Off
indicates the connection is no established
Blinking amber
indicates the hard drive I/O activity
Off
indicates there is no hard drive I/O activity
Green :
USB device detected & ready to backup
Blinking green :
Data backup in progress
Amber :
Data backup process failed
Blinking amber
: Data backup configuration has not been set.
Off:
Standby for backup or backup process completed successfully
18
EonNAS Pro Series Hardware Manual
Drive Tray LEDs
Two (2) LED indicators are located on the right hand side of each drive tray. When notified by a drive failure message, you should check the drive tray indicators to find the exact failed drive.
No. LED LED Color & Status
FLASHING blue
indicates data is being written to or read from the drive. The drive is busy.
1. Drive Busy LED
OFF
indicates that there is no activity on the disk drive.
2.
Power Status
LED
GREEN
indicates that the drive bay is populated and is working normally.
RED
indicates that the disk drive has failed, or a connection problem occurred.
1
2
19
EonNAS Pro Series Hardware Manual
Ethernet Port LEDs
200 / 500 / 800 210 / 510 / 810 850
No. LED Status
1. Activity Blinking amber
indicates data transfer activity
2.
Link Status
LED
Steady green
indicates connection established
Off
indicates connection not established
20
EonNAS Pro Series Hardware Manual
1Gbps iSCSI Host Ports (selected models only)
1
2
1
2
No. LED LED Color & Status
1.
Link Status
LED
Steady green
indicates 1000 Mb connection established.
Off
indicates 10/100 Mb connection established.
Blinking amber
indicates data transfer activity.
Off
indicates there is no I/O activity.
21
EonNAS Pro Series Hardware Manual
10Gbps iSCSI Host Ports (selected models only)
CH3 CH4
1
2
LED status Color
Steady ON
Flashing
Green
Green
LED Color & Status
Steady green
indicates a link has been established
Flashing green
indicates an active link
The 10Gbps host connectivity is achieved by inserting SFP+ into the SFP+ cages on iSCSI ports and data signals are sent through optical cables.
The 10Gbps iSCSI allows for optical connections, only. Optical cables can be used over longer distances and are more reliable. Due to the demands of high transfer rates, optical cables are preferred for 10Gb iSCSI connectivity.
22
EonNAS Pro Series Hardware Manual
The following transceiver and cables have been tested and proven to be compatible with your systems.
Item part number Description
IFT-9370CSFP10G-0010 Small Form Pluggable 10Gb Optical Transceiver
IFT-9270CFCCab01
IFT-9270CFCCab02
Optical FC cable, LC-LC, MM-62.5/125, Duplex, LSZH,
O.D.=1.8mmx2, 1 Meter
Optical FC cable, LC-LC, MM-62.5/125, Duplex, LSZH,
O.D.=1.8mmx2, 5 Meters
IFT-9270CFCCab03
Optical FC cable, LC-LC, MM-62.5/125, Duplex, LSZH,
O.D.=1.8mmx2, 10 Meters
The 10Gb iSCSI host ports connect to host adapters (HBA) that feature a 10Gbps transfer rate, SFP+ interface, and support full-duplex transfer. The HBA card best come with a 64-bit/133MHz PCI-X or PCI-E interface.
WARNING!
The SFP transceiver contains a laser diode featuring class 1 laser (incompliance with Code of Federal Regulations (CFR), Title 21, Part 1040).
All cables are sensitive and must be handled with care. To prevent interference within a rack system, the cable routing path must be carefully planned and the cables must not be bent.
Lasers
CAUTION!
Lasers can be hazardous and may cause permanent eye damage or blindness, and therefore must be treated and used with caution. Never look directly at the lasers.
23
EonNAS Pro Series Hardware Manual
Hardware Installation
Component Compatibility
The use of compatible components is strongly recommended to ensure compatibility, quality and normal operation with your system. Please contact your vendor for a list of compatible components.
Before You Start
Items received in the package:
The NAS system and hard drive trays (preinstalled into the system)
Two Ethernet cables
Quick installation guide
CD-ROM
There are some tools and components that are user provided:
a small size flat-blade screwdriver for unlocking and locking hard drive trays
At least one 3.5 inch SATA hard drive (up to 3TB per drive is supported).
NOTE
Users MUST install at least one hard drive into slot 1 to setup the system.
WARNING
For internal airflow and safety reasons, please remove only one hard drive tray at a time and never leave two or more hard drive bays empty without drive tray!
Airflow Concerns
Allow 20cm of ventilation clearance around the enclosure. Make sure cables are also placed well clear of the ventilation area behind the enclosure and away from foot traffic.
24
EonNAS Pro Series Hardware Manual
Installing Hard Drives
Hard drives are purchased separately. When purchasing hard drives, please consider the following factors:
Hard Disk Drive Prerequisites
Capacity (MB/GB)
: Use hard drives that have the same capacity and rotation speeds.
RAID arrays use a “least-common-denominator” approach meaning the maximum capacity used in each drive for comprising a logical configuration is the maximum capacity of the smallest drive. Profile: The enclosure drive bays are designed for
3.5-inch wide x 1-inch pitch hard drives.
Drive Interface Type
: The enclosure accommodates SATA-II (3Gbps) and SATA-III
(6Gbps) hard drives up to 3TB in capacity per hard disk drive.
NOTE
Only install hard drives into the enclosure after the system has been placed in the desired setup location. If hard drives are installed first, the system may be too heavy to handle and possible impact during transportation may damage your hard drives.
DO NOT
attempt to shift or tilt the system once the system has powered on to avoid damaging the hard drives.
NEVER
remove two or more hard drive trays out of the system at the same time!
Hot-swappable Hard Drives
The hard drives in drive trays are hot swappable components. Please refer to the
Software Manual for RAID configuration details and the maintenance section of this manual on how to replace hard drives.
25
EonNAS Pro Series Hardware Manual
Drive Tray Numbering Sequence
2x0 5x0
8x0
Tray numbering sequence is important because if any faults occur to disk drives, you should be able to identify the location of a faulty drive. Below is a list of the level of fault tolerance for different RAID levels:
RAID Level
Minimum disk requirement
Max. No. of Failed Drives without Data Loss
Non-RAID 1
No fault tolerance. 1 drive fails and the data is lost.
Recognizing drive location is important. For example, if you mistakenly remove 2 drives from a RAID5 logical drive, data will be lost.
For detail RAID configuration methods, please refer to the Web Interface Manual.
26
EonNAS Pro Series Hardware Manual
Installing Hard Drive into the Drive Tray
1. Open the front panel of the system.
2. Press the release button (indicated by the
blue arrow
) on the bezel, the bezel panel should open automatically and gently pull out the hard drive tray.
3. Place the hard drive into the drive tray. Make sure the hard drive’s interface connector is facing the open side of the drive tray and its label side facing up.
Adjust the drive’s location until the mounting holes in the drive tray are aligned with those on the hard drive. Secure the drive with four (4) supplied flat head screws.
27
EonNAS Pro Series Hardware Manual
4. With the tray bezel open, insert the hard drive and tray into the system enclosure.
5. Close the tray bezel.
6. Use the small flat blade screwdriver to turn the bezel lock from the unlock to lock position.
7. Repeat above steps to install other hard drives.
8. Close the system front panel when you are done installing hard drives.
NOTE
When hot-swapping hard drive(s), a beep should sound to indicate the hard drive has been detected by the system followed by the
lighting up green.
28
EonNAS Pro Series Hardware Manual
Connections, Powering-on & Initialization
Connecting the NAS System
2
NOTE
Make sure you have at least installed one hard drive into the NAS system.
3
4
5
1
1
The system connection requires the user to
(1)
Connect an Ethernet cable from the NAS system to a switch / router
(2)
Place the CD that came with the system into your PC’s CD-ROM
(3)
Connect an Ethernet cable from the “SAME” switch / router to the PC
(4)
Connect the power cable to the NAS system and to a power outlet
(5)
Press the power button to start up the system
29
EonNAS Pro Series Hardware Manual
Powering On the System for the First Time
The initialization process only occurs if it is the first time you power on your system.
Before you power-on, please make sure you have done the following:
1. Have a Windows OS PC ready for use.
2. Install at least one (1) hard drive into enclosure’s hard drive slot 1 for the initialization process.
3. For 850 series, make sure the ATX power switch is in the “OFF” position (shown on the right).
4. Make sure you have connected the following:
One end of the Ethernet cable to Ethernet port 1 (indicated by the
blue circle
) and the other end into a switch.
The adaptor plug / power cable to the power socket (indicated by the
blue rectangle
) and the other end into a power outlet.
EonNAS
1
2
5. Power-on peripheral devices first (eg. switches, routers, servers, PCs, etc.).
6. For 850 systems, turn the ATX power switch to the “ON” position.
NOTE
To manually setup the system, users can log in using the default Ethernet 1 IP address
<10.0.0.2>; default Ethernet 2 IP address <10.0.0.3>; default username: admin, default password: admin.
For details, please refer to the Web Interface Manual for details.
30
EonNAS Pro Series Hardware Manual
Powering-on the System & Initialization
WARNING
Hard drive data will be erased!
NOTE
Turn off Windows firewall
:
To turn off the Windows firewall, please refer to the instructions below.
Windows 7/ Vista:
Click on the Start button > Control Panel > Security > Windows Firewall > turn off Firewall. You may be prompted for an administrator password or confirmation, type the password or provide confirmation.
Windows XP:
Click on the Start button > Control Panel > Windows Firewall > turn off
Firewall.
1. Approximately 5 minutes after pressing the power button (if the user is near the system, after pressing the power button, a beep will sound after 2 minutes and two beeps will sound 3 minutes thereafter) double click on found in the “fscommand" folder on the CD. A NasFinder window will appear.
2. Select your preferred interface language.
3. Highlight your system and click the “Connect” button.
Discovered Device List
Name
NAS_500
Model
NAS-500
IP Address
10.0.0.2
NOTE
If your NAS system was not found
•
Make sure your PC and NAS are connected to the same switch / router!
•
Try turning off the antivirus’ firewall (please refer to its manual) then close the
NasFinder and go back and start from step 3.
•
Please refer to the setup instructions in the User Manual on the CD.
31
EonNAS Pro Series Hardware Manual
4. The “Set IP” button will light up. Click on it so the NasFinder can set an IP address for your EonNAS system.
5. The IP settings window appears with an IP address, click the Connect button, the following browser window will appear. Click on “OK”. When a prompt appears asking for password, please enter “admin”.
Set IP
Inter face
IP A ddress
Netm as k
Gateway
Atheros Ar8131 PCI-E Gig
192 . 168 . 0 . 2
255 . 255 . 255 . 0
192 . 168 . 0 . 253
OK Close
6. Wait for 5 seconds and:
A. Click the “Find” button on your NasFinder.
B. Highlight the EonNAS system that matches the IP address set previously.
C. Click the “Connect” button.
b
Discovered Device List
32
a
Find
L an g ua ge
Connect
c
Set IP
Close
EonNAS Pro Series Hardware Manual
7. The following screen will appear. Fill in your system’s settings.
Host Name
: Enter a unique name for your EonNAS system.
Timezone
: Select your local time zone.
Password
: Enter a new password for the admin account. (default: admin)
H os t Na m e
NAS_500
Tim ez o ne
(GMT-08:00)America/Los_Angeles
P as s wo rd
C on firm Pa s s wo rd
Click the “Next” button.
8. Unless you want to change the IP address, leave the current settings and click the Next button.
Interface
LAN1
LAN2
DHCP
DHCP
IP Address Netmask
Gateway
Link
9. Enter a unique name, select the protection level, and click the Next button.
Pool Name:
Data Protection Level:
Pool-1
Best Protection
RAID 1: Provides best protection. Your data will be mirrored.
Better Protection
RAID 6: Provides protection against two simultaneous drive failures.
Good Protection [Recommended]
RAID 5: Provides protection against one drive failure.
No Protection
RAID 0: Provides no protection but offers maximum capacity.
Number of Drives: 4
Usable Capacity: 698.66 GB
Click the “Next” button.
10. Add at least one user account for accessing the new storage pool and click the Next button. (The default user account is username: guest, password: guest.)
Name g ue st
Password
Confirm Password Home Directory
Click the “Next” button.
11. You can change the default shared folder settings or add a new folder and
33
EonNAS Pro Series Hardware Manual click the Next button.
Folder
E on S ha re
Access Rights
Full Control
Full Control
Full Control
Read Only
Read Only
Read Only
Click the “Next” button.
12. V iew the summary of configurations. Click Back to modify the parameters or
Apply to complete the Startup Wizard. Press OK to initialize or to reboot when prompted!
13. Upon reboot, when you hear two beeps, you may then log into and use your
EonNAS system (the whole process may take approximately 20 minutes to complete).
During the initializing process, the OS of the system will be copied onto the installed hard drive(s). This initialization process may take up to 20 minutes.
The Quick Initialization process creates the following:
One storage pool "EonPool" with all drives
Non-RAID with only one HDD; RAID 1 with two HDDs or RAID 5, when more than two HDDs installed
One shared volume "EonShare"
One account with username: guest; password: guest with full access
Default admin account name: admin; password: admin
NOTE
Remember to turn back on your Windows and antivirus’ firewall. Setting can be found in the same location as the turning off option.
34
EonNAS Pro Series Hardware Manual
Quick Initialization Using Systems’ LCD Screen
NOTE
The quick initialization method is NOT the recommended way to initialize the system as default settings will be applied. Changes can later be made using its GUI interface.
Approximately 5 minutes after pressing the power button (if the user is near the system, after pressing the power button, a beep will sound after 2 minutes and two beeps will sound 3 minutes thereafter) the following message will appear on the LCD:
Press the “Select” button to move the cursor to “Yes”, press the “Enter” button and the system will begin the automated process and the screen will show “Initializing…”.
SE LEC T
Q u i c k i n i t i a l i z e
- > Y e s N o
E NTE R
SE LEC T
I n i t i a l i z i n g . . .
E NTE R
When initialization has completed, the LCD will show the following:
R e b o o t i n g . . .
SE LECT
E NTE R
The reboot process takes approximately 3 minutes.
If you press the “Enter” button with the cursor pointed at No, it will bring you to the main system menu screen, which is described in the following section.
SE LECT
Q u i c k i n i t i a l i z e
- > Y e s N o
E NTE R
SE LECT
E o n N A S _ P r o _ x x x x x x . x x x . x x x . x x x
E NTE R
35
EonNAS Pro Series Hardware Manual
Setting up the System Using LCD Screen Menu
This section describes the menus and sub-menus shown on the LCD module and how to setup and change the settings within.
Due to the vast menus and sub-menus that are available on the LCD module, it is recommended that users NOT use the LCD module to set up the system. It is recommended that users refer to the Web Interface Manual to setup the system using the web interface!
36
EonNAS Pro Series Hardware Manual
Main Menu
For systems with a LCD screen, it provides users with basic system statuses and
TCP/IP configuration settings. To setup specific settings, users need to log into the web user interface (please refer to the Web Interface Manual).
NOTE
It is recommended that users log into the web user interface to configure the system.
There are seven (7) sub-menu selections: TCP/IP, Physical Disk, Pool, System, Shut
Down, Reboot and Back.
S E LE CT
E o n N A S _ P r o _ x x x x x x . x x x . x x x . x x x
E N T E R
S E LE CT
C a p a c i t y u t i l i z a t i o n : 6 3 %
E N T E R
M a i n m e n u
N e t w o r k
S E LE CT
E N T E R
M a i n m e n u
H a r d d i s k
S E LE CT
E N T E R
M a i n m e n u
P o o l
S E L EC T
E N T E R
M a i n m e n u
S y s t e m
S E L EC T
E N T E R
M a i n m e n u
S h u t d o w n
S E L EC T
E N T E R
M a i n m e n u
R e b o o t
S E L EC T
E N T E R
M a i n m e n u
[ G o b a c k ]
S E L EC T
E N T E R
SELECT
ENTER
37
EonNAS Pro Series Hardware Manual
TCP/IP – LAN1 / LAN2 Menu
From the Main Menu, press the “SELECT” button to reach the TCP/IP menu and press the “ENTER” button to go into the TCP/IP sub-menu (LAN 1 example is shown below).
SELECT
Eo nNA S_P ro_ xxx xx x.x xx. xxx .xx x
ENTER
Ma in me nu
Ne two rk
SELECT
ENTER
SELECT
ENTE R
SELECT
L AN 1 - IP a dd r es s
1 92 . 1 68 . 0 00 . 03 2
ENTER
SELECT
ENTE R
SELECT
L A N 1 - n e t m a s k
2 5 5 . 2 5 5 . 2 5 5 . 0 0 0
ENTE R
M ai n me nu
H ar d di sk
SELECT
ENTER
M a in m e nu
P o ol
SELECT
EN TE R
M a in m e nu
S y st e m
SELECT
ENTE R
M a in m e nu
S h ut d o w n
SELECT
ENTE R
T C P / IP
G a t e w a y
SELECT
ENTE R
T C P / I P
D N S
SELECT
E NT ER
T C P / I P
[ G o b a c k ]
SELECT
ENTE R
SELECT
L A N 1
A d va n c e se t t i n gs
ENTE R
L A N 1
[ G o b a c k ]
SELECT
ENTE R
M a in m e nu
R e bo o t
SELECT
ENTE R
SELECT
SELECT
ENTE R
ENTER
M a in m e nu
[ G o b a c k]
Setting IP addresses
Press the “ENTER” button to enter the sub-menu (LAN1 – IP) from “TCP / IP – LAN1” to configure an IP address and an underline cursor appears (eg. 192.168.000.032).
With the underline cursor beneath the number you wish to modify, press the “SELECT” button and the digit will change incrementally. Once you have set the desired number, press the “ENTER” button and the cursor will move onto the next digit (eg.
192.168.000.032). The rest of the IP addresses are configured likewise.
Note:
The specific LAN 0, LAN1, Gateway and DNS settings can also be configured in the web interface. Please refer to the Web-Interface Manual for details.
38
EonNAS Pro Series Hardware Manual
LAN 1 – Enter Settings Menu
If LAN 1 did not establish a connection, the following menus will appear:
M a i n m e n u
N E t w o r k
SELECT
ENTER
T C P / I P
L A N 1
SELECT
ENTER
SELECT
L A N 1 - I P a d d re s s
0 . 0 . 0 . 0
ENTER
L A N 1
[ G o b a c k ]
SELECT
ENTER
SELECT
L A N 1
A d v a n c e s e t ti n g s
ENTER
When LAN 1 has established a connection, menus will appear with IP addresses:
M a i n m e n u
N e t w o r k
SELECT
ENTER
T C P / I P
L A N 1
SELECT
ENTER
SELECT
L A N 1 - I P a d d re s s
1 9 2 . 1 6 8 . 0 0 0 .0 3 2
ENTER
L A N 1
[ G o b a c k ]
SELECT
ENTER
SELECT
L A N 1
A d v a n c e s e t ti n g s
ENTER
SELECT
L A N 1 - N e t m a s k
2 5 5 . 2 5 5 . 2 5 5 .0 0 0
ENTER
39
EonNAS Pro Series Hardware Manual
Once you are in the “LAN 1 Enter Settings” screen, you can configure detail LAN settings (settings can also be configured using the web interface, please refer to the
Web Interface Manual).
SEL ECT
L AN 1
A dv a n c e s et t i n g s
EN T ER
[ G o ba c k ]
SELECT
EN T ER
SEL ECT
N et w o r k s et t i n g s
E na b l e D H CP
EN T ER
SELECT
N e t w o rk s e t t i n g s
E n a b l e s t a t i c I P
EN TER
SELECT
N e t w o r k s e t t i n g s
D i s a b l e L A N
EN T ER
A re y o u s u r e ?
- > Y e s N o
SEL ECT
EN T ER
SELECT
S e t I P a d d r e s s
1 9 2 . 1 68 . 0 0 0 . 0 3 2
EN TER
A r e y o u s u r e ?
- > Y e s N o
SELECT
EN T ER
SELECT
S e t n e t m a s k
2 5 5 . 2 55 . 2 5 5 . 0 0 0
EN TER
SELECT
ENTER
A r e yo u s u r e ?
- > Y e s N o
SELECT
EN TER
To configure an IP address, press the “ENTER” button to access the Set IP Address screen and an underline cursor appears (eg. 192.168.000.032). With the underline cursor beneath the number you wish to modify, press the “SELECT” button and the digit will change incrementally. Once you have set the desired number, press the
“ENTER” button and the cursor will move onto the next digit (eg. 192.168.000.032).
The rest of the IP addresses are configured likewise.
Note:
LAN 2 settings are also configured likewise with users pressing the “ENTER” button at the LAN 2 screen.
40
EonNAS Pro Series Hardware Manual
Gateway Menu
There are Gateways -0, -1, -2 menus and if a gateway has been setup, the menus will show “Local host” and when setup, it will show an IP address:
M a i n m e n u
N e t w o r k
SEL EC T
E N T E R
T C P / I P
L A N 1
SEL EC T
E N T E R
T C P / I P
L A N 2
SEL EC T
E N T E R
G a t e w a y - 1
1 7 2 . 1 8 8 . 0 . 1
SEL EC T
E N T E R
SELECT
EN TER
G a t e w a y - 2
L o c a l h o s t
SEL EC T
E N T E R
G a t e w a y - 0
L o c a l h o s t
SEL EC T
E N T E R
SEL EC T
G a t e w a y
A d d n e w g a t e w a y ?
E N T E R
T C P / I P
G a t e w a y
SEL EC T
E N T E R
G a t e w a y
[ G o b a c k ]
SEL EC T
E N T E R
41
EonNAS Pro Series Hardware Manual
Once you are in the “Gateway Local host” screen, you can configure detail gateway settings (settings can also be configured using the web interface, please refer to the
Web Interface Manual).
T C P / I P
G a t e w a y
SELECT
ENTER
G a t e w a y - 0
L o c a l h o s t
SELECT
ENTER
G a t e w a y
A d d n e w g a t e w a y
SELECT
ENTER
G a t e w a y
[ G o b a c k ]
SELECT
ENTER
D e s t i n a t i o n
L o c a l h o s t
SELECT
ENTER
N e t m a s k
[ I P a d d r e s s ]
SELECT
ENTER
G a t e w a y
L o c a l h o s t
SELECT
ENTER
SELECT
S e t d e s t i n a t i o n
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0 ENTER
SELECT
S e t n e t m a s k
2 5 5 . 2 5 5 . 2 5 5 . 0 0 0
ENTER
SELECT
S e t g a t e w a y
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
ENTER
C o n f i g
D e l e t e g a t e w a y
SELECT
ENTER
A r e y o u s u r e ?
- > Y e s N o
SELECT
ENTER
[ G o b a c k ]
SELECT
ENTER
SELECT
E NTER
Press the “ENTER” button to enter the sub-menu (Set Destination) from the screen
“Gateway - Add New Gateway” and you will see an underline cursor (eg.
0
00.000.000.000). To configure the destination IP address, press the “SELECT” button with the underline cursor beneath the number you wish to modify. By pressing the
“SELECT” button, the digit will change incrementally. Once you have set the desired number, press the “ENTER” button and the cursor will move onto the next digit (eg.
000.000.000.000). The rest of the IP addresses are configured likewise.
42
EonNAS Pro Series Hardware Manual
If a Gateway has been setup, an “IP address (xxx.xxx.xxx.xxx)” will appear in the menus. Once you are in the “Gateway-1 [IP address]” screen, you can change the gateway settings (settings can also be configured using the web interface, please refer to the Web-Interface Manual).
T C P / I P
G a t e w a y
S E LE CT
E N T E R
G a t e w a y - 1
[ I P A d d r e s s ]
S E LE CT
E N T E R
G a t e w a y
A d d n e w g a t e w a y
S E LE CT
E N T E R
G a t e w a y
[ G o b a c k ]
S E LE CT
E N T E R
D e s t i n a t i o n
[ I P a d d r e s s ]
S E LE CT
E N T E R
M a s k
[ I P a d d r e s s ]
S E LE CT
E N T E R
G a t e w a y
L o c a l h o s t
S E LE CT
E N T E R
S E LE CT
S e t d e s t i n a t i o n
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
E N T E R
S E LE CT
S e t n e t m a s k
2 5 5 . 2 5 5 . 2 5 5 . 0 0 0
E N T E R
S E LE CT
S e t g a t e w a y
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
E N T E R
A r e y o u s u r e ?
- > Y e s N o
S E LE CT
E N T E R
D e l e t e G a t e w a y
S E LE CT
E N T E R
[ G o b a c k ]
S E LE CT
E N T E R
SELECT
ENTER
To configure the destination IP address, please refer to the previous page for instructions.
43
EonNAS Pro Series Hardware Manual
DNS Menu
The path to the DNS screen is shown below:
M a i n m e n u
N e t w o r k
SELECT
ENTER
T C P / I P
L A N 1
SELECT
ENTER
T C P / I P
L A N 2
SELECT
ENTER
T C P / I P
[ G o b a c k ]
SELECT
ENTER
T C P / I P
D N S
SELECT
ENTER
T C P / I P
G a t e w a y
SELECT
ENTER
To access the DNS settings, the path is shown below:
M a i n m e n u
N e t w o r k
SELECT
ENTER
T C P / I P
L A N 1
SELECT
ENTER
T C P / I P
L A N 2
SELECT
ENTER
D N S - 0
[ I P a d d r e s s ]
SELECT
ENTER
T C P / I P
D N S
SELECT
ENTER
T C P / I P
G a t e w a y
SELECT
ENTER
44
EonNAS Pro Series Hardware Manual
If a DNS has been setup, an “IP address (xxx.xxx.xxx.xxx)” will appear in the menus.
Once you are in the “DNS-x [IP address]” screen, you can change (add or delete) the
DNS settings. Deleting adding any one of the DNS settings will bring you back to the main “TCP / IP DNS” screen (settings can also be configured using the web interface, please refer to the Web Interface Manual).
T C P / I P
D N S
SELECT
ENTER
D e l e t e D N S - 0
[ I P a d d r e s s ]
SELECT
ENTER
D e l e t e D N S - 1
[ I P a d d r e s s ]
SELECT
ENTER
D N S
A d d n e w D N S
SELECT
ENTER
A r e y o u s u r e ?
Y e s - > N o
SELECT
ENTER
A r e y o u s u r e ?
Y e s - > N o
SELECT
ENTER
SELECT
N e w D N S
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
ENTER
A r e y o u s u r e ?
Y e s - > N o
SELECT
ENTER
D N S
[ G o b a c k ]
SELECT
ENTER
Press the “ENTER” button to enter the sub-menu (Add New DNS) from the screen
“DNS – Add New DNS” and you will see an underline cursor (eg. 000.000.000.000). To configure a DNS IP address, press the “SELECT” button with the underline cursor beneath the number you wish to modify. By pressing the “SELECT” button, the digit will change incrementally. Once you have set the desired number, press the “ENTER” button and the cursor will move onto the next digit (eg. 000.000.000.000). The rest of the IP addresses are configured likewise.
45
EonNAS Pro Series Hardware Manual
Physical Disk Menu
The Physical disk menu does not have user configurable settings. The numbers of hard drives that will appear when you press the “SELECT” button depends on the number of hard drives installed.
SELECT
E o n N A S _ P r o _ x x x x x x . x x x . x x x . x x x
E NT ER
M a i n m e n u
N e t w o r k
SELECT
E NT ER
D i s k 1
S i z e : x x x G B
SE LECT
E NTE R
M a i n m e n u
H a r d d i s k
SE LE CT
E NTER
M ai n m e nu
P oo l
SE LECT
E NTE R
M ai n m e nu
S ys t e m
SE LECT
E NTE R
D i s k 2
S i z e : x x x G B
SE LECT
E NTE R
D i s k 3
S i z e : x x x G B
SE LECT
E NTE R
D i s k 4
S i z e : x x x G B
SE LECT
E NTE R
M ai n m e nu
S hu t d ow n
SE LECT
E NTE R
D i s k 5
S i z e : x x x G B
SE LECT
E NTE R
M ai n m e nu
R eb o o t
SE LECT
E NTE R
M ai n m e nu
[ Go ba c k]
SE LECT
E NTE R
SELECT
ENTER
[ G o b a c k ]
SE LECT
E NTE R
46
EonNAS Pro Series Hardware Manual
Pool Menu
The pool menu does not have configuration settings. When users press “ENTER” to access the pool sub-menu, it displays the current pool(s) created. In the example below, it shows a pool with
672GB
storage capacity configured in RAID 5 (
utilizing disks 1, 2 and 3
) and another pool with
500GB
storage capacity configured in RAID 1
(
utilizing disks 4 and 5
).
SELECT
E o n N A S _ P r o _ x x x x x x . x x x . x x x . x x x
E NT ER
M a i n m e n u
N e t w o r k
SELECT
E NT ER
M a i n m e n u
H a r d d i s k
SE LE CT
E NTER
M ai n m e nu
P oo l
SE LECT
E NTE R
M ai n m e nu
S ys t e m
SE LECT
E NTE R
M ai n m e nu
S hu t d ow n
SE LECT
E NTE R
M ai n m e nu
R eb o o t
SE LECT
E NTE R
M ai n m e nu
[ Go ba c k]
SE LECT
E NTE R
R A I D 5 6 7 2 G B
D i s k I D s : 1 2 3
SE LEC T
E NTE R
R A I D 1 5 0 0 G B
D i s k I D s : 4 5
SE LEC T
E NTE R
[ G o b a c k ]
SE LEC T
E NTE R
R A I D 5 6 7 2 G B
D i s k I D s : 1 2 3
R A I D 1 5 0 0 G B
D i s k I D s : 4 5
SELECT
ENTER
47
EonNAS Pro Series Hardware Manual
System Menu
The System menu has no user configurable settings. It displays system statuses such as CPU temperatures and system fan’s operational speeds.
SELECT
E o n N A S _ P r o _ x x x x x x . x x x . x x x . x x x
E NT ER
M a i n m e n u
N e t w o r k
SELECT
E NT ER
M a i n m e n u
H a r d d i s k
SE LE CT
E NTER
M ai n m e nu
P oo l
SE LECT
E NTE R
M ai n m e nu
S ys t e m
SE LECT
E NTE R
M ai n m e nu
S hu t d ow n
SE LECT
E NTE R
SE LECT
C P U
T e m p e r a t u r e : 3 0 C
E NTE R
SE LECT
S y s t e m
T e m p e r a t u r e : 3 0 C
E NTE R
F a n 1 : 3 0 0 0 R P M
F a n 2 : 3 0 0 0 R P M
SE LECT
E NTE R
[ G o b a c k ]
SE LECT
E NTE R
M ai n m e nu
R eb o o t
SE LECT
E NTE R
M ai n m e nu
[ Go ba c k]
SE LECT
E NTE R
SELECT
ENTER
48
EonNAS Pro Series Hardware Manual
Shutdown
Press the “Enter” button to bring up the confirmation screen (Yes or No). Press the
“Select” button to choose yes or no and the “Enter” button to make your selection. The system will sound one beep before shutting down. If you press Enter while selecting:
Yes: system shuts down (a beep will sound)
No: returns to the previous menu
SELEC T
E o n N A S _ P r o _ x x x x x x . x x x . x x x . x x x
E NT ER
M a i n m e n u
N e t w o r k
SELECT
E NT ER
M a i n m e n u
H a r d d i s k
SE LE CT
E N TER
SELECT
ENTER
M ai n m e nu
P oo l
SE LECT
E NTE R
M ai n m e nu
S ys t e m
SE LECT
E NTE R
M ai n m e nu
S hu t d ow n
SE LECT
E NTE R
S h u t d o w n ?
Y e s - > N o
SE LEC T
E NTE R
SE LECT
S h u t t i n g d o w n . . .
E N TE R
M ai n m e nu
R eb o o t
SE LECT
E NTE R
M ai n m e nu
[ Go ba c k]
SE LECT
E NTE R
Note:
If the system becomes unresponsive, users can force shutdown the system. To force shut down the system, press and hold (approx. 5 seconds) the power button until the system shuts down. This should only be done when the system is unresponsive!
49
EonNAS Pro Series Hardware Manual
Reboot
Press the “ENTER” button to bring up the confirmation screen (yes or no). Press the
“SELECT” button to choose yes or no and the “ENTER” button to make your selection.
When you press the ENTER button with the arrow pointing at:
Yes: system reboots (a beep will sound)
No: returns to the previous menu
Once you have configured all your system settings, you may begin to create pool(s) for network storage.
SELECT
E o n N A S _ P r o _ x x x x x x . x x x . x x x . x x x
E NT ER
M a i n m e n u
N e t w o r k
SELECT
E NT ER
M a i n m e n u
H a r d d i s k
SE LE CT
E N TER
M ai n m e nu
P oo l
SE LECT
E NTE R
SELECT
ENTER
M ai n m e nu
S ys t e m
SE LECT
E NTE R
M ai n m e nu
S hu t d ow n
SE LECT
E NTE R
R e b o o t ?
Y e s - > N o
SE LEC T
E NTE R
R e b o o t i n g . . .
SE LECT
E N TE R
M ai n m e nu
R eb o o t
SE LECT
E NTE R
M ai n m e nu
[ Go ba c k]
SE LECT
E NTE R
50
EonNAS Pro Series Hardware Manual
Connections
Component Compatibility
The use of compatible components is strongly recommended to ensure compatibility, quality and normal operation with your system. Please contact your vendor for a list of compatible components.
Connection Concept
Use CAT5e or better quality Ethernet cables, router and switch to construct your
Ethernet network.
PC
PC
PC
PWR
ESC EN T
GbE HBA
RAID
PC
J BOD
S E L E C T
E N T E R
GbE /10Gb iSCSI
Users can trunk (black dotted circle) Ethernet ports 1 and 2 to boost the bandwidth.
Users can also create pools
Please refer to the Web Interface Manu
and folders to share over the network.
The blue shaded area applies to selected expansion connectivity m odels only (shown using a
red line
connected to the NAS system). The expansion ports on selected
models allow for extra connectivity to RAID and JBOD storage expansion (please refer to respective RAID and expansion enclosure manuals for details).
51
EonNAS Pro Series Hardware Manual
eSATA External Expansion Port
eSATA devices are hot-swappable.
The eSATA port can be used for external hard drive expansion (connecting to eSATA capable enclosures) or other eSATA capable devices. Most eSATA devices gain operating power from USB ports. It is essential to plug in the eSATA connector to the eSATA device and to the eSATA port before powering on (connecting USB connectors or an adaptor to supply power).
1
2
200 / 500 / 800 210 / 510 / 810 850
52
EonNAS Pro Series Hardware Manual
USB External Expansion Port
USB devices are hot-swappable.
The USB ports on the back of NAS systems can be used for external storage expansion purposes or peripheral devices. For USB expansion or peripheral device details, please refer to the manual that came with your USB device.
Some systems come with USB 3.0 ports labeled (shown in green below).
1
2
200 / 500 / 800 210 / 510 / 810 850
53
EonNAS Pro Series Hardware Manual
USB Quick Backup Functionality
The USB port located at the bottom right corner can be used for One-Touch Copy.
Users MUST setup their systems beforehand to perform this task (please refer to the
Web Interface Manual). You can find the One-Touch Copy settings under the following directory: Backup > One-Touch Copy in the web interface. For details, please refer to the Web Interface Manual.
For Systems Without LCD Screen
Please refer to descriptions here for USB quick backup LED status
details.
54
EonNAS Pro Series Hardware Manual
For systems with a LCD screen
Simply plug in a USB flash drive to the front USB port and the LCD will display the following:
O n e t o u c h c o p y ?
- > Y e s N o
SELECT
ENTER
Press the “Select” button to choose between the options and “Enter” to execute your selection. When completed, the LCD will display the following:
O n e t o u c h c o p y c o m p l e t e d
SELECT
ENTER
When the One-Touch copy function has failed, the LCD will display the following:
O n e t o u c h c o p y f a i l e d
SELECT
ENTER
When the “One touch copy” function has NOT been setup and a USB flash drive is plugged into the front USB port, it will show the following:
O n e t o u c h c o p y , n o t c o n f i g u r e d
SELECT
ENTER
Pressing the ENTER or SELECT button will bring you to the following screen:
SELECT
E x t e r n a l U S B d i s k d r i v e r e a d y
ENTER
From here, pressing the ENTER or SELECT button will bring you back to the main menu.
SELECT
E o n N A S _ P r o _ x x x x x x . x x x . x x x . x x x
ENT ER
55
EonNAS Pro Series Hardware Manual
Maintenance
WARNING
Replace a failed hard disk drive from the system as soon as possible to ensure data redundancy.
When inserting a hard drive, do not use excessive force. Forcing the hard drive can damage the connector pins either on the hard drive itself or the backplane within the system enclosure.
DO NOT
remove two or more hard drive trays out of the enclosure at the same time!
Should you suffer multiple hard drive failures, always replace one hard drive at a time!
User replaceable components:
Replacing the Hard Drive
. If the power status lights up red, it indicates that that particular hard disk drive has failed. Hard drives are hot swappable, to replace it, please refer to the following procedure:
1. Locate the failed hard drive with a red status LED (
2. Unlock the hard drive tray by turning the bezel to the unlock position.
56
EonNAS Pro Series Hardware Manual
3. Open the tray bezel by pushing the release button (indicated by the
blue arrow
) and the front bezel will automatically open.
4. Remove the drive tray by pulling it one inch away from the drive bay. Wait for at least 30 seconds for the hard drive to spin-down, and then gently and carefully remove the drive tray from the chassis.
5. Remove the four (4) retention screws that secure the hard drive from the sides of the drive tray (two on each side).
6. Install the replacement hard drive as shown below and reinserted into the
enclosure (or refer to Installing Hard Drives ).
Connector end
57
EonNAS Pro Series Hardware Manual
System Error Buzzer
Note:
For systems without a LCD screen
, if you hear an error buzzer, please log into the system through a browser and check the system log.
The LCD module provides basic action(s) and monitoring statuses only, it is recommended that in an event of an error, users log into the web-interface to get a better picture of the overall system statuses!
If your system has encountered an error, a single beep buzzer alarm will sound continuously until you manually turn it off and a “Mute Buzzer -> Yes No” prompt will show on the LCD module. With the arrow pointed at “Yes”, press the “ENTER” button to turn off the buzzer.
M u t e b u z z e r ?
- > Y e s N o
SELECT
EN TER
Once an error has occurred, users must log into the web interface and check the system logs to identify the issue(s). Below is a list of the possible triggering events and simple countermeasures.
1. CPU or system temperature exceeded the threshold limit:
When you have determined the CPU or system temperature is the cause of the system error, please check for obstructions in front of and behind the system enclosure to ensure normal airflow is sustained. If error persists, please contact
.
2. System fan failure:
When you have determined the system fan has completely failed or is operating below its normal rev range, please contact
.
3. Hard drive failure:
When you have determined a hard drive or hard drive(s) have failed.
Press the “ENTER” button with the arrow pointed at “Yes” to mute the buzzer.
58
EonNAS Pro Series Hardware Manual
Open the front system panel cover and check all hard drive status LEDs. Normal operation hard drive’s power status LED should light up green, failed hard drive power status LEDs will light up
red
.
Once you have located the failed hard drive, remove it out of the system and
replace it with a new one (please refer to replacing the hard drive ).
NOTE
When hot-swapping (while system is in operation), once you have inserted the hard drive, a beep will sound to indicate the hard drive has been detected by the system
followed by the power status LED
lighting up green.
*Please turn over the page to see the system’s alternative action!
Buzzer Sounds
Type Description
Short beep
1. When system is booting
2. Shutting down the System
3. System reset successfully
4. Firmware has been updated
5. USB One-Touch copy started / completed (front USB port)
6. Plugged-in external device recognized
7. External backup started / completed (scheduled and rear USB ports only)
8. Pool rebuilding or completed
9. Two short beeps will sound (with a pause in between) to indicate the system is booting into NAS OS
Repetitive
Long beep
1. Storage capacity utilization is at 95%
2. Storage capacity utilization is full
3. RAID in degraded mode
4. System anomaly (cooling fan, power, high temperature)
5. Failed operation (USB OT copy or external backup failed)
6. System reset failed
*For setting schedule(s) or viewing system log(s), please refer to the web interface manual.
59
EonNAS Pro Series Hardware Manual
The following occurs when the alarm sounds but is not attended to within 30 seconds.
The “Mute Buzzer -> Yes No” screen will be replace with the “System
Error! Check Logs” screen while the alarm continues to sound and the system status
LED lights
red
.
SELECT
S y s t e m e r r o r !
C h e c k s y s t e m l o g
EN TER
From here, to mute the buzzer, you must navigate your way through the main menu, shown below in the
red dotted rectangle
:
SE LE CT
S y s t e m e r r o r !
C h e c k s y s t e m l o g
EN T E R
S ELE CT
E o n N A S _ P r o _ x x x x x x . x x x . x x x . x x x
E N T E R
M a i n m e n u
N e t w o r k
S E LE CT
E N T E R
M a i n m e n u
H a r d d i s k
S E LE CT
E N T ER
M a i n m e n u
P o o l
SE L EC T
E N T E R
M a i n m e n u
S y s t e m
S EL EC T
EN T E R
M a i n m e n u
S h u t d o w n
S E L EC T
E N T E R
SELECT
ENTER
M a i n m e n u
R e b o o t
S E L EC T
E N T E R
M a i n m e n u
M u t e b u z z e r
S EL EC T
E N T E R
M u t e b u z z e r ?
- > Y e s N o
SE L EC T
E N T E R
M a i n m e n u
[ G o b a c k ]
S EL EC T
E N T E R
From here, once you have rectified the error and the “Main Menu Mute Buzzer” menu will disappear from the main menu selection.
60
EonNAS Pro Series Hardware Manual
Restore Default Settings
Under the following circumstances, you may need to restore to system default settings:
You forgot your password and you are unable to access the NAS server
Note:
Restoring the system to its default settings should be your last option. The restore default function will disable Jumbo Frame, reset port trunking settings and reset the
“Admin” user account back to default (account: admin / password: admin).
The restored “settings” will search the network in DHCP mode for 3 minutes and if unsuccessful in acquiring an IP address, it will revert to the default IP address of
10.0.0.2 for Ethernet port 1 and 10.0.0.3 for Ethernet port 2; default username: admin, default password: admin.
To restore default settings:
1. Stop all system I/Os.
2. Use the tip of a pen to press and hold the restore default button for 3 ~ 5 seconds and release, a beep will sound to indicate that default settings have been restored.
1
2
200 / 500 / 800 210 / 510 / 810
61
850
EonNAS Pro Series Hardware Manual
Appendix
Technical Specifications
Hardware
Dimensions
EonNAS Pro 2x0:
102(W) x 245 (D) x 150 (H) mm
EonNAS Pro 5x0
: 175(W) x 245(D) x 225(H) mm
EonNAS Pro 8x0
: 175(W) x 245(D) x 310(H) mm
EonNAS Pro 850 series
: 175(W) x 380(D) x 310(H) mm
Storage
Onboard LAN
Cooling
Hard drives:
EonNAS Pro 2x0:
2 hot-swappable 3.5” SATA HDDs
EonNAS Pro 5x0
: 5 hot-swappable 3.5” SATA HDDs;
EonNAS Pro 8x0:
8 hot-swappable 3.5” SATA HDDs
RAID Levels:
EonNAS Pro 2x0
: 0, 1
EonNAS Pro 5x0 / 8x0 RAID levels
: 0, 1, 5, 6, 10
EonNAS Pro 850 series RAID levels
: 0, 1, 5, 6, 10, 50, 60
Note
:
There are minimum disk number requirements for
certain RAID configuration. Please refer to this table
for details.
Please use hard drives of the same spindle speed and storage capacity!
2 x GbE Ethernet RJ-45 ports
2 system fans
* All designs and hardware specifications are subject to change without prior notice.
For the latest specifications and details, please contact your vendor.
62
EonNAS Pro Series Hardware Manual
Operating Environment
Temperature
Humidity
Operating: 5 to 40ºC (32º F to 104º F);
Operating: 5% to 80%, non-condensing
Host Port Pinouts
Interface
EonNAS
Pro 2x0
EonNAS
Pro 5x0
EonNAS
Pro 8x0
EonNAS
Pro 8x0-1
EonNAS
Pro 8x0-2
1Gbps iSCSI Host
Port
V
10Gbps iSCSI Host
Port
1Gbps
Ethernet
Port
V
V V V V V
63
EonNAS Pro Series Hardware Manual
1Gbps Ethernet Host Port
1
2
Pin Name
1 BI_DA+
2 BI_DA-
3 BI_DB+
4 BI_DC+
Pin Name
5 BI_DC-
6 BI_DB-
7 BI_DD+
8 BI_DD-
NOTE
Automatic MDI/MDI-X Crossover: Crossover can be implemented internally at hub or switch or externally through twisted pair media.
64
1Gbps iSCSI Host Port
EonNAS Pro Series Hardware Manual
1
2
Pin Name
1 BI_DA+
2 BI_DA-
3 BI_DB+
4 BI_DC+
Pin Name
5 BI_DC-
6 BI_DB-
7 BI_DD+
8 BI_DD-
NOTE
Automatic MDI/MDI-X Crossover: Crossover can be implemented internally at hub or switch or externally through twisted pair media.
65
EonNAS Pro Series Hardware Manual
10Gbps iSCSI Host Port
CH3 CH4
1
2
Pin
1 V
EET
Name
2 T
FAULT
3 T
DIS
4 MOD_DEF(2)
Transmitter ground
Description
Transmitter fault indication – High indicates a fault condition
Transmitter Disable – Module electrical input disables on high or open
5
6
7
8
9
MOD_DEF(1)
MOD_DEF(0)
No Connect
RX_LOS
No Connect
Module definition 2 – Two wire serial ID interface data line (SDA)
Module definition 1 – Two wire serial ID interface clock line (SCL)
Module definition 0 - Grounded in module (module present indicator)
Internal pullup 30KΏ to Vcc
Indicates loss of signal; High indicates loss of received optical signal
Internal pullup 30KΏ to Vcc
10 V
EER
Ground
11 V
EER
Ground
12 RD- Inverse Received DATA Out
13 RD+ Received Data Out
66
EonNAS Pro Series Hardware Manual
14 V
EER ground
15 V
CCR
Receiver
16 V
CCT
Transmitter power +3.3V
17 V
EET
18 TD+
19 TD-
20 V
EET
Inverse Transmitter Data In
67
EonNAS Pro Series Hardware Manual
Certifications
Safety
EMC
Environment
Others
UL (60950-1 2’nd)
BSMI CNS 14336: 2005
CB IEC 60950-1, 2’nd Edition
GOST-R GOST R 60950-1-2005
EN 55022: 2006/A1:2007
EN 55024:1998/A1:2001/A2:2003
EN 61000-3-2:2006/A1:2009/A2:2009
EN 61000-3-3:2008
BSMI (CNS 13438)
FCC (FCC Part 15,subpart B )
IEC 60068-2
MIL-STD-810E/883E
ISTA
ASTM-D3332
ISO 4180
ISO 7779/3744
EU RoHS
China RoHS
68
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement