advertisement
HP LaserJet M1319 MFP Series – Copy
Copy using the automatic document feeder (ADF)
How do I?
Load originals using the automatic document feeder (ADF)
Steps to perform
1 Insert the top-end of the stack of originals into the ADF input tray, with the media stack face-down and the first page to be copied at the bottom of the stack.
2 Make sure that the ADF media lever is set correctly for single-page or multiple-page documents.
CAUTION: To prevent damage to the product, do not use an original that contains correction tape, correction fluid, paper clips, or staples. Also, do not load photographs, small originals, or fragile originals into the ADF.
3 Slide the stack into the ADF until it does not move any farther.
Document loaded appears on the control-panel display.
4 Adjust the media guides until they are snug against the media.
Document loaded
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
1 www.hp.com
HP LaserJet M1319 MFP Series – Copy
Collate my copy job
How do I?
Change the copy-collation setting for the current job
Steps to perform
1 Press Set-up then select Copy setup.
2 Use the arrow buttons to select Def Collation.
3 Select the number of copies.
4 Press Start Copy to save the selection and immediately start the copy job.
-or-
5 Press OK to save the selection without starting the job.
Copy setup
Def Collation
10
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
1 www.hp.com
HP LaserJet M1319 MFP Series – Copy
Copy on both sides (Duplex)
How do I?
Copy a two-sided original to a one-sided document
Steps to perform
1 Load the first page of the document to be copied facedown into the ADF.
2 Press Start Copy.
3 Flip the original, and then reload it into the ADF.
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
4 Press Start Copy .
5 Repeat steps 1 through 4 for each page until all of the original document pages have been copied.
1 www.hp.com
HP LaserJet M1319 MFP Series – Copy
How do I?
Copying a two-sided original to a two-sided document
Steps to perform
1 Load the first page of the document to be copied facedown into the ADF.
2 Press Start Copy .
3 Flip the original, and then reload it into the ADF.
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
4 Remove the copied page from the output bin and place it face down into the priority input tray.
2 www.hp.com
HP LaserJet M1319 MFP Series – Copy
How do I?
Copying a two-sided original to a two-sided document (continued)
Steps to perform
5 Press Start Copy .
6 Remove the copied page from the output bin, and then set it aside for manual collating.
7 Repeat steps 1 through 6, following the original document page order, until all pages of the original are copied.
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
3 www.hp.com
HP LaserJet M1319 MFP Series – Copy
Copy on preprinted letterhead or forms
How do I? Steps to perform
1 On the product control panel, press Setup .
Change the default media-size setting
2 Use the arrow buttons to select System setup, and then press OK .
3 Use the arrow buttons to select Paper setup, and then press OK .
4 Use the arrow buttons to select Def. paper size, and then press OK .
Paper setup
Def. paper size
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
1 www.hp.com
HP LaserJet M1319 MFP Series – Copy
How do I?
Change the default media-size setting
(continued)
Steps to perform
5 Use the arrow buttons to select a media size, and then press OK .
6 Press OK to save the selection.
Letter
Change the default media-type setting
1 On the product control panel, press Setup .
2 Use the arrow buttons to select System setup, and then press OK .
System setup
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
2 www.hp.com
HP LaserJet M1319 MFP Series – Copy
How do I?
Change the default media-type setting
(continued)
Steps to perform
3 Use the arrow buttons to select Paper setup, and then press OK .
4 Use the arrow buttons to select Def. paper type, and then press OK .
5 Use the arrow buttons to select a media size, and then press OK .
Paper setup
Def. paper type
Letterhead
6 Press OK to save the selection.
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
3 www.hp.com
HP LaserJet M1319 MFP Series – Copy
Make my copy look better
How do I?
Adjust the copy quality for the current job
Steps to perform
1 On the product control panel, press Quality to see the current quality setting for the copy.
2 Use the arrow buttons to scroll through the quality setting options.
3 Select a setting, and then press Start Copy to save the selection and immediately start the copy job, or press
OK to save the selection without starting the job.
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
1 www.hp.com
HP LaserJet M1319 MFP Series – Copy
Reduce or enlarge the image
How do I?
Reduce or enlarge copies for the current job
Steps to perform
1 On the product control panel, press Reduce/Enlarge .
NOTE: If you select Custom: 25 to 400%, type a percentage by using the alphanumeric buttons.
If you select 2 pages per sheet or 4 pages per sheet, select the orientation (portrait or landscape).
2 Select the size to which you would like to reduce or enlarge the copies in this job.
3 Press Start Copy to save the selection and immediately start the copy job, or press OK to save the selection without starting the job.
1 Press Setup .
Adjust the default copy size
NOTE: The product can reduce copies to as little as 25% of the original size or enlarge copies to as much as 400% of the original size.
2 Use the arrow buttons to select Copy setup, and then press OK .
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
1 www.hp.com
Copy setup
HP LaserJet M1319 MFP Series – Copy
How do I?
Adjust the default copy size (continued)
Steps to perform
3 Use the arrow buttons to select Def. Redu/Enlrg, and then press OK .
4 Use the arrow buttons to select the option for how you normally want to reduce or enlarge copies.
Def. Redu/Enlrg
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
2 www.hp.com
HP LaserJet M1319 MFP Series – Copy
Copy on media of different sizes and types
How do I?
Media sizes and types
Steps to perform
Media-size settings
● Letter
● Legal
● A4
Media-type settings
● Plain
● Preprinted
● Letterhead
● Transparency
● Prepunched
● Labels
● Bond
●
●
●
●
●
●
●
Recycled
Color
Light
Heavy
Cardstock
Envelope #10
Rough
1 On the product control panel, press Setup .
Change the default media-size setting
2 Use the arrow buttons to select System setup, and then press
OK .
System setup
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
1 www.hp.com
HP LaserJet M1319 MFP Series – Copy
How do I?
Change the default media-size setting
(continued)
Steps to perform
3 Use the arrow buttons to select Paper setup, and then press
OK .
4 Use the arrow buttons to select Def. paper size, and then press
OK .
5 Use the arrow buttons to select a media size, and then press
OK .
6 Press OK to save the selection.
Change the default media-type setting
1 On the product control panel, press Setup .
Paper setup
Def. paper size
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
2 www.hp.com
HP LaserJet M1319 MFP Series – Copy
How do I?
Change the default media-type setting
(continued)
Steps to perform
2 Use the arrow buttons to select System setup, and then press
OK .
3 Use the arrow buttons to select Paper setup, and then press
OK .
4 Use the arrow buttons to select Def. paper type, and then press
OK .
5 Use the arrow buttons to select a media type, and then press
OK .
6 Press OK to save the selection.
System setup
Paper setup
Def. paper type
© 2008 Copyright Hewlett-Packard
Development Company, L.P.
3 www.hp.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project