IBM SBC-659P User's Manual

SBC-659P

Half- size Intel FC-370 Pentium III CPU

Card with Intel 815E chipset, Dual LAN,

Audio, Dual COMs, LCD & 4 USB.

Copyright Notice

This document is copyrighted, 2001. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable. However, the original manufacturer assumes no responsibility for its use, nor for any infringements upon the rights of third parties which may result from its use.

The material is this document is for product information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, AAEON, assumes no liabilities resulting from errors or omissions in this document, or from the use of the information contained herein.

AAEON reserves the right to make changes in the product design without notice to its users.

Part No. 2087659010 SBC-659P 1st Edition

A1.0 Printed in Taiwan December., 2001

Acknowledgments

All other product names or trademarks are properties of their respective owners.

AMD is a trademark of Advanced Micro Devices, Inc.

AMI is a trademark of American Megatrends, Inc.

Award is a trademark of Award Software International, Inc.

IBM, PC/AT, PS/2, and VGA are trademarks of International

Business Machines Corporation.

Intel and Pentium III are trademarks of Intel Corporation.

Microsoft Windows ® is a registered trademark of Microsoft Corp.

SMC is a trademark of Standard Microsystems Corporation.RTL is a trademark of Realtek Semi-Conductor Co., Ltd.

C&T is a trademark of Chips and Technologies, Inc.

UMC is a trademark of United Microelectronics Corporation.

ITE is a trademark of Integrated Technology Express, Inc.

SiS is a trademark of Silicon Integrated Systems Corp.

VIA is a trademark of VIA Technology, Inc.

A Message to the Customer

AAEON Customer Services

Each and every AAEON product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new AAEON equipment is destined for the laboratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name AAEON has come to be known.

Your satisfaction is our primary concern. Here is a guide to

AAEON's customer services. To ensure you get the full benefit of our services, please follow the instructions below carefully.

Technical Support

We want you to get the maximum performance from your products.

So if you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones we can give over the phone.

So please consult this manual first. If you still cannot find the answer, gather all the information or questions that apply to your problem, and with the product close at hand, call your dealer. Our dealers are well trained and ready to give you the support you need to get the most from your AAEON products. In fact, most problems reported are minor and are able to be easily solved over the phone.

In addition, free technical support is available from AAEON engineers every business day. We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products.

Product Warranty

AAEON warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of shipment.

This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by AAEON, or which have been subject to misuse, abuse, accident or improper installation. AAEON assumes no liability under the terms of this warranty as a consequence of such events.

Because of AAEON's high quality-control standards and rigorous testing, most of our customers never need to use our repair service.

If an AAEON product is defective, it will be repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you will be billed according to the cost of replacement materials, service time, and freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For example, CPU type and speed, AAEON products used, other hardware and software used, etc.) Note anything abnormal and list any on-screen messages you get when the problem occurs.

2. Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA

(return material authorization) number from your dealer. This allows us to process your return more quickly.

4. Carefully pack the defective product, a fully-completed Repair and Replacement Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container.

A product returned without proof of the purchase date is not eligible for warranty service.

5. Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer.

Packing list

Before you begin installing your card, please make sure that the following materials have been shipped:

• 1 SBC-659P Half- size Single Board Computer Card

• 1 Quick Installation Guide

• 1 Support CD contains the followings:

-- User's Manual (this manual in PDF file)

-- Ethernet driver and utilities

-- Chipset driver and utilities

-- Audio driver and utilities

• 1 floppy disk drive interface cable (34-pin, pitch 2.0mm)

• 1 IDE hard disk drive cable (40-pin, pitch 2.54mm)

• 1 parallel port (26-25-pin, pitch 2.0mm) and serial port (10-9 pin, pitch 2.0mm) adapter kit.

• 1 bag of screws and miscellaneous parts

If any of these items are missing or damaged, contact your distributor or sales representative immediately.

Notice

Dear Customer,

Thank you for purchasing the SBC-659P board. This user's manual is designed to help you to get the most out of the SBC-659P, please read it thoroughly before you install and use the board. The product that you have purchased comes with an two-year limited warranty, but AAEON will not be responsible for misuse of the product. Therefore, we strongly urge you to first read the manual before using the product.

To receive the latest version of the user manual, please visit our

Web site at:

Http:\\WWW.AAEON.COM

http://www.aaeon.com

Contents

Chapter 1: General Information.........................................1

I n t r o d u c t i o n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Features .................................................................................... 3

Specifications ........................................................................... 4

Board layout ............................................................................. 7

Board dimensions ..................................................................... 8

Chapter 2: Installation ........................................................ 9

Safety Precautions........................................................... .. 10

Removing the CPU..................................................10

Installing A CPU ..............................................................11

Setting Jumpers...................................................12

Installing SODIMM......................................................13

Jumpers ...............................................................14

Connectors..........................................................15

Location of Jumpers and Connectors..................................16

Location of solder side Connectors.................................17

Mechnical Drawing..................................................18

Mechnical Drawing.................................................19

Clear CMOS(JP2)..................................................20

Front Panel(JP1)...................................................20

System Freqency(JP3)...............................................21

COM2(Ring, +5V, +12V)...............................................22

RS-232/422/485 COM2 setting(JP5,JP6)................................23

Digital Video Output(CN1)..........................................24

External Power On Connector (CN2)...................................25

IDE Hard Drive Connector(CN3).....................................26

USB Connector(CN5,CN6)............................................27

Floppy Drive Connector(CN9).......................................28

VGA Connector (CN8).................................................29

Audio Connector(CN9).............................................30

Ethernet Connector (CN12, CN10)..................................31

COM1(CN13), COM2(CN11) Serial Ports..............................32

Internal Keyboard Connector(CN15).................................33

Power Connector(CN16).............................................33

Parallet Port Connector(CN17).....................................34

PS/2 Keyboard and Mouse Connector(CN18)..........................35

IrDA Connector(CN19)..............................................35

CPU Fan Power Connector(CN20)..................................36

North Bridge chip Fan Connector(CN21)..............................36

Compact Flash Connector (CN22)...................................37

Chapter 3: Award BIOS Setup........................................... 38

Starting setup............................................................ .. ......39

Setup keys..................................................................... . ..40

Getting help ............................................................................. 41

Main setup menu ..................................................................... 42

Standard CMOS Features ....................................................... 44

Advanced BIOS Features ....................................................... 49

Advanced CHIPSET Features ............................................... 54

Integrated Peripherals...............................................58

Power Management Setup ...................................................... 63

PNP/PCI Congfiguration Setup .............................................. 67

PC Health Status......................................................69

Frequecy Voltage Control........................................70

Load Fail-Safe Defaults............................................71

Load Optimized Defaults..........................................72

Set Supervisor Password.......................................73

Set User Password...............................................74

Save to CMOS and Exit.........................................75

Exit Without Saving.............................................76

Chapter 4: Drivers and Utilities ......................................77

Installation of Drivers: Notice ................................................ 78

Chipset Driver ......................................................................... 79

Ultra ATA Driver .................................................................... 80

Windows 95/98 ..................................................................... 8 1

Intel 82559 Driver for 95 or 98 Version 1. .................................81

VGA Driver for 95/98............................................82

Audio Driver for 95/98...........................................83

Windows NT ......................................................................... 8 4

Security Driver for NT............................................84

Ultra ATA Storage Driver for NT...........................85

VGA Driver For NT..............................................86

Audio Driver For NT.............................................87

Intel 82559 Driver for NT......................................88

Windows 2000..................................................................89

VGA Driver for 2000.............................................89

Audio Driver for 2000.............................................90

General

Information

This chapter gives background information of the mainboard.

Sections Include:

• Board Specifications

• Layout and Dimensions

1

Chapter 1 General Information 1

Introduction

If your requirements for a single board computer consist of a half-sized footprint, dual Ethernet, PISA interface and Intel quality logic chipset, then SBC-659P is the solution. This half-sized single board computer is ideal for internet data access server.

The dual Ethernet socket ensures consistent high server throughput and transparent backup connections in corporate servers. Two RJ-45 connectors controlled by two Intel 82559GD chipsets offering 10/

100Base Ethernet interface.

The processors used on this single board computer may vary, however to acquire the full potential of this embedded computer we suggest

Intel Celeron 533~766MHz or Pentium III offering 300~766MHz (With system bus frequencies of 66 MHz), Celeron 800MHz-1.2GHz or

Pentium III 500-900MHz(With system bus frequencies of 100MHz), or

Pentium III 533MHz-1.26GHz (With system bus frequencies of

133MHz)and Tualatin CPU up to 1.26GHz . We strongly recommand using thermal grease when you add on an over 1GHz processors.

The logic chipset onboard is entirely Intel, controlling the LCD, LAN and audio functions.

This half-sized board features an audio interface, supporting microphone in, line in/out, and CD in capabilities. Codec job tasking are performed by ALC 200 chip. The VGA has a display memory size of

4MB, supporting non-interlaced CRT and up to 18/24/36/48-bit LCD through panel link or LVDS module.

On the solder side we offer a 144-pin SODIMM socket providing a maximum of 256MB of memory. A compact flash connector is provided onboard. For expansion modules a PC/104 connector is integrated into this half-sized card.

SBC-659P supports one IDE channel, dual floppy disk, four USB ports onboard, two RS-232 serial ports and of which one can be configured as RS-232/422/485. The single bi-directional parallel ports can support

SPP, ECP and EPP modes. The standard AT/ATXpower connector

2 enables this half sized SBC to be operated without a backplane if necessary.

SBC-659P User Manual

Features

Supports Intel Celeron/ Tualatin/Pentium III FC-370 CPUs

Notice: It doesn't support 0.25 micron process CPU.

Two 10/100 Base-T Fast Ethernet ( 2 intel 82559GD)

Notice: It doesn't support WOL function in this version

Supports H/W status monitoring

Integrated AC-97 2.1 SoundBlaster compatible PCI 3D Audio

Onboard Intel 815E controller supports 18/24/36/48-bit TFT panel

Supports Compact Flash Memory

Supports PC-104 modules

Four USB ports onboard

Two COM ports onboard

DVO interface onboard

PISA bus interface


Specifications

Standard Half-size SBC functions

• CPU: FC-370 Pentium III (Coppermine), Celeron, Tualatin and compatible

CPUs (With system bus frequencies of 66/100/133MHz).

• CPU socket: 370 pins Socket

• BIOS: Award 2 MB Flash BIOS

• Chipset: Intel 815E

• I/O chipset: ITE 8712F.

• Memory : Onboard one 144 pins SODIMM socket supports up to

256Mbytes SDRAM (PC-100/133 SDRAM supported).

• Enhanced IDE: One IDE channel. Support Ultra DMA/ 100

mode with data transfer rate of 100MB/sec.

• FDD interface: Supports two floppy disk drives, 5.25" (360KB and

1.2MB) and/or 3.5" (720KB, 1.44MB, and 2.88MB).

• Parallel port: One bi-directional parallel ports. Supports SPP, ECP, and

EPP modes.

• Serial port: Two RS-232 serial ports can be configured as COM1, COM2,

or disabled individually and of which one can be configured as RS-

232/422/485 (COM2). (16C550 equivalent).

• IRDA interface: Supports SIR and CIR

• KB/Mouse connector : 6-pin mini-DIN connector supports PC/AT

keyboard and PS/2 mouse and wake on KBD function.

• USB connectors: Two 10-pin onboard connectors supports four USB ports.

• Battery: Lithium battery for data retention

• Watchdog timer: Can generate a system reset, IRQ15, or NMI.

Software selectable time-out interval (1 sec. ~ 255 sec, 1 sec./step)

• DMA: 7 DMA channels (8237 equivalent)

• Interrupt: 15 interrupt levels (8259 equivalent)

4 SBC-659P User Manual

Power management: Supports AT/ATX power supply. I/O peripheral

support power saving and doze/standby/suspend modes. APM 1.2

compliant.

H/W status monitoring: Embedded in ITE 8712F supports power,

supply voltages, and temperature monitoring.

LED status pin header:LED status indicator for power, HDD, and LAN.

Flat Panel/CRT Interface

• Chipset: embedded In Intel 815E

• Display memory: Share system memory 4MB SDRAM (Max)

• Display type: Supports non-interlaced CRT and up to 18/24/36/48 bit

LCD (TFT LCD, only). Can display both CRT and Flat Panel simulta

neously.

Audio Interface

• Chipset: Intel 815E

•Audio interface: One 14 pin header for microphone in, line in, line out,

and CD-IN.

• Codec: ALC 200

Ethernet Interface

• Chipset: Two Intel 82559GD

• Ethernet interface : Dual 10/100Base-Tx RJ-45 connectors. LAN LED support (Active, Link, Speed)

Compact Flash socket onboard

• Compact flash connector onboard support type 2 CFD


Mechanical and environmental

Power supply voltage: +5V, -5V, +12V, -12V

Operating temperature: 32 to 140 o F (0 to 60 o C)

Board size: 7.3"(L) x 4.8"(W) (185mm x 122mm)

Weight: 0.3 Kg

OS version recomandation: Win 98 or above


Board Layout


Board Dimensions


2

Installation

This chapter describes how to set up the main board hardware, including instructions on setting jumpers and connecting peripherals, switches, and indicators. Be sure to read all the safety precautions before you begin the installation procedure.

Chapter2 Installation 9

SBC-659P

Safety precautions

Warning! Always completely disconnect the power cord from your chassis whenever you are working on it. Do not make connections while the power is on because sensitive electronic components can be damaged by the sudden rush of power. Only experienced electronics personnel should open the

PC chassis.

Caution! Always ground yourself to remove any static charge

before touching the CPU card. Modern electronic

devices are very sensitive to static electric charges. Use

a grounding wrist strap at all times. Place all electronic

components on a static-dissipative surface or in a static-

shielded bag when they are not in the chassis.

Removing the CPU

The SBC-659P all-in-one CPU module supports most Pentium III/

Celeron CPUs. The system's performance depends on the CPU you choose. You can install or upgrade the CPU in the board's PGA socket by following the procedures outlined below. If your system has an existing CPU, you need to remove it before installing the new CPU.

Removing a CPU

1. Disconnect power from the chassis, and unplug all connections to the CPU card. Then, remove the CPU card from the chassis by following the instructions in the user's manual for your chassis.

2. Lift the CPU out of the PGA socket. The old chip may be difficult to remove. You may find spray chip lubricant, designed for pin-grid-array (PGA) devices, and a chip puller helpful.

These are available at electronics hobbyists' supply stores.

1 0 SBC-659P Installation Guide

BC-599/596

Installing A CPU

To install the CPU, follow the instructions that came with it. If no documentation was provided, the general procedures for installing a CPU are outlined below:

1. Lubricate the pins on the CPU with lubricant for PGA devices.

This makes the CPU slide in much easier and greatly reduces the chance of damaging the pins and other components.

2. Carefully align the CPU so that it is parallel to the socket. Make sure that the notch on the corner of the CPU matches the notch on the inside of the socket.

3. Gently push the CPU into the socket. There will probably be a small gap between the CPU and the socket even when it is fully seated. DO NOT USE EXCESSIVE FORCE!

When you install a new CPU, you may have to adjust other settings on the board, such as CPU type, CPU clock, and PCI speed, to accommodate it. Make sure that the settings are correct for your CPU. Improper settings may damage the CPU.


SBC-659P

Setting jumpers

You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To

“close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3. In this case you would connect either pins

1 and 2 or 2 and 3.

1

2

3

O p e n Closed Closed 2-3

The jumper settings are schematically depicted in this manual as follows:

1 2 3

O p e n Closed Closed 2-3

A pair of needle-nose pliers may be helpful when working with jumpers.

If you have any doubts about the best hardware configuration for your application, contact your local distributor or sales representative before you make any changes.

Generally, you simply need a jumper to make most connections.


BC-599/596

Installing SODIMM

Supplementary information about DIMM

Your SBC-659P can accept both regular and PC-100/133 SDRAM

DIMM Module. Onboard one 144-pin SODIMM socket supports up to 256MB of memory.

Single-sided modules are typically 16 or 128MB; double-sided modules are usually 32 or 256 MB.

Memory Installation Procedures

To install SODIMM, first make sure you are holding the SODIMM memory module at a 45 degree angle. Slowly slide the SODIMM module along the plastic guides on both ends of the socket. Then press the module right down into the socket, until you hear a click.

This is when the two handles have automatically locked the memory module into the correct position of the SODIMM socket.

To remove the memory module, just push both handles outward, and the memory module will be ejected by the mechanism in the socket.


SBC-659P

Jumpers

Jumpers

JP1(1-2)

JP2

JP3

JP4

JP5

JP6

JP1(3-4)

JP1(5-6)

JP1(7-8)

JP1(9-10)

Function

Front Panel (Power On Button)

Front Panel (IDE Driver LED)

Front Panel (External Speaker)

Front Panel (Case Open)

Front Panel (Reset)

Clear CMOS

FSB Frequency Select

COM2 Ring/+5/+12 V Select

COM2 RS-232/422/485 Select

COM2 RS-232/422/485 Select


BC-599/596

Connectors

Connector Function

CN1 DVO Output Connector

CN2 External Power On Connector

CN3 IDE Connector (ATA100)

CN4 No used

CN5 USB 2-3 Connector

CN6 USB 0-1 Connector

CN7 Floppy Drive Connector

CN8 VGA Connector

CN9 Audio Connector

CN10 100 Base-Tx Ethernet Connector (Intel 82559)

CN11 COM2 RS-232/422/485 Serial Port Connector

CN12 100 Base-Tx Ethernet Connector (Intel 82559)

CN13 COM1 RS-232 Serial Port Connector

CN14 PC-104 Connector

CN15 Internal Keyboard Connector ,

CN16 ATX Power Connector

CN17 Parallel Port Connector

CN18 PS/2 Keyboard/Mouse Connector

CN19 IrDA Connector

CN20 CPU Fan Power Connector

CN21 North Bridge chip Fan Connector

CN22 Compact Flash Connector


SBC-659P

Locating Jumpers and Connectors


BC-599/596

Locating of Solder Side Connectors


SBC-659P

Mechanical Drawing


BC-599/596

Mechanical Drawing

0


SBC-659P

Clear CMOS (JP2)

You can use JP2 to clear the CMOS data if necessary. To reset the

CMOS data, place a jumper on JP2 (Clear CMOS) for just a few seconds, and then remove the jumper to the (Protect) position.

Clear CMOS (JP2)

Clear CMOS

1 2 3

JP2

Default

Protect

1 2 3

Front Panel (JP1)

Front Panel (JP1)

1 2

3 4

5 6

7 8

9 10

GND/Power on Button

IDE LED- / IDE LED +

Speaker - / Speaker +

Case Open / GND

Reset Switch+ / GND


BC-599/596

System Frequency (JP3)

CPU/Auto Detect SDRAM/Auto Detect

1 2

3 4

*Default: Auto Detect


SBC-659P

COM2 (Ring, +5V, +12V) JP4

+12V

2 4 6

1 3 5

+5V

2 4 6

1 3 5

Ring

2 4 6

Default

1 3 5


BC-599/596

RS-232/422/485 COM2(JP5,JP6) Setting

RS-232 JP5 JP6

1 3

4 6

Default

7 9

10 12

1 2

3 4

5 6

RS-422 JP5 JP6

1 3

4 6

7 9

10 12

1 2

3 4

5 6

RS-485 JP5 JP6

1 3

4 6

7 9

10 12

1 2

3 4

5 6


SBC-659P

Digital Video Output Connector (CN1)

Digital Visual Output Connector (CN1)

Pin Signal Pin

A1

A2

FTCLK0

FTCLK1

B1

B2

A3

A4

CRT-HSYNC

FTBLNK #

B3

B4

A5

A6

A7

A8

FTHSYNC

FTVSYNC

SL_STALL

GND

A9 3VFTSCL

A10 3VFTSDA

A11 3VHTPLG

A12 +5V

A13 PCIRST #

A14 +12V

Signal

FTD0

FTD1

FTD2

GND

B5

B6

B7

B8

FTD3

FTD4

FTD5

CRT-VSYNC

B9 FTD6

B10 FTD7

B11 FTD8

B12 VEE_OK

B13 FTD9

B14 FTD10

A15 FPVDDEN

A16 GND

A17 PGMSEL

A18 SMBCLK

A19 SMBDATA

A20 +5V

B15 FTD11

B16 +3.3V

B17 +3.3V

B18 GND

B19 +3.3V

B20 FPBKLENR


BC-599/596

External Power On Connector (CN2)

4

5

2

3

External Power On Connector (CN2)

Pin

1

Signal

NC

6

GND

NC

GND

PS-ON

5VSB


SBC-659P

IDE Hard Drive Connector (CN3)

29

31

33

35

21

23

25

27

37

39

13

15

17

19

7

9

11

IDE hard drive connector (CN3)

3

5

Pin

1

Signal

IDE RESET

DATA 7

DATA 6

4

6

Pin Signal

2 GND

DATA 8

DATA 9

DATA 5

DATA 4

DATA 3

DATA 2

DATA 1

DATA 0

SIGNAL GND

8

10

12

14

16

18

20

DATA 10

DATA 11

DATA 12

DATA 13

DATA 14

DATA 15

N/C

REQ

IO WRITE

IO READ

IO READY

DACK

IRQ14

ADDR 1

ADDR 0

CS#1

IDEACTP

30

32

34

36

22

24

26

28

38

40

GND

GND

GND

GND

GND

N.C.

ATA66DETECT

ADDR 2

CS#3

GND


BC-599/596

USB connector (CN5, CN6)

The SBC-659P provides four USB (Universal Serial Bus) interfaces, which give complete plug and play, hot attach/detach for up to 127 external devices. The USB interfaces comply with USB specification Rev. 1.1, and can be disabled in the system BIOS setup.

USB 0-1 connector (CN6)

7

9

3

5

Pin

1

Function

+5V

USBD0-

USBD0+

GND

GND

Pin Function

2

4

6

8

GND

GND

USBD1+

USBD1-

10 +5V

7

9

3

5

USB 2-3 connector (CN5)

Pin

1

Function

+5V

Pin Function

2 GND

USBD2 4

USBD2+ 6

GND

GND

8

GND

USBD3+

USBD3-

10 +5V


SBC-659P

Floppy Drive Connector (CN7)

27

29

31

19

21

23

25

33

Floppy drive connector (CN7)

Pin

1

3

Signal

GND

GND

Pin

2

4

11

13

15

17

5

7

9

GND

GND

GND

GND

GND

GND

GND

12

14

16

18

6

8

10

GND

GND

GND

GND

GND

N.C.

GND

N.C.

28

30

32

20

22

24

26

34

Signal

DENSITY SELECT

N.C.

N.C.

INDEX

MOTOR A

DRIVE SELECT B

DRIVE SELECT A

MOTOR B

DIRECTION

STEP

WRITE DATA

WRITE GATE

TRACK 0

WRITE PROTECT

READ DATA

SIDE 1

DISK CHANGE


BC-599/596

VGA connector (CN8)

VGA display connector (CN8)

CN8 is a 15-pin, D-SUB connector used for conventional CRT displays.

5

6

3

4

7

8

VGA display connector (CN8)

Pin Signal

1 RED

2 GREEN

Pin

9

10

BLUE

N/C

GND

GND

GND

GND

15

16

11

12

13

14

Signal

VCC

GND

N/C

DDCSDA

H-SYNC

V-SYNC

DDCSCL

N/C


SBC-659P

Audio Connector (CN9)

On board SBC-659P, there is a 14-pin header for audio capability.

The pin definition is provided below.

Audio connector (CN 9)

Pin

1

3

Signal

MIC IN

GND

Pin

2

4

Signal

MIC VCC

CD GND

5 LINE IN L 6 CD IN L

7 LINE IN R 8 CD GND

9 GND 10 CD IN R

11

13

LINE OUT L 12 LINE OUT R

GND 14 GND


BC-599/596

Ethernet Connectors(CN12,CN10)

Onboard supports two standard RJ-45 connector for Ethernet connection. The RJ-45 connector has two LED indicators. Both

LED displays indicate the speed of information being processed.

* The on board Intel 82559GD fast Ethernet controller supports

10Mb/s and 100Mb/s N-way auto-negotiation operation.

6

7

4

5

100Base-Tx Ethernet connector (CN12)

Pin

1

2

3

Signal

TCT

TX+

TX-

Pin

8

9

10

Signal

ACTIVE LED

SPEED LED

3VSB

RX+

RX-

RCT

LINK LED

11

12

13

14

NC

NC

GND

GND

5

6

3

4

7

100Base-Tx Ethernet connector (CN10)

Pin

1

2

Signal

TCT

TX+

Pin

8

9

Signal

ACTIVE LED

SPEED LED

TX-

RX+

RX-

RCT

LINK LED

10

11

12

13

14

3VSB

NC

NC

GND

GND


SBC-659P

COM 1 (CN 13) & COM 2 (CN 11) Serial Ports

On board offer two serial ports for serial devices connection. Pin definitions show as below.

5

7

9

COM 1 RS-232 (CN13)

Pin Signal Pin Signal

1 DCD1 2 RXD1

3 TXD1 4 DTR1

GND 6

RTS1 8

RI 10

DSR1

CTS1

N.C.

5

7

9

COM 2 RS-232/422/485 (CN11)


1 DCD2(422TXD-/485DATA-) 2 RXD2 (422RXD+)

3 TXD2(422TXD+/485DATA+) 4 DTR2 (422RXD-)

GND

RTS2

RI

6

8

10

DSR2

CTS2

N.C.


BC-599/596

Internal Keyboard Connector (CN15)

3

4

5

Internal keyboard connector (CN 15)

Pin

1

Signal

CLK

2 Data

NC

GND

+5V

Power connector (CN16)

ATX power connector (CN16)

The ATX power supply uses 20-pin connector shown below. Make sure you plug in the right direction.

7

8

9

10

4

5

6

ATX power connector (CN16)

2

3

Pin

1

Signal

NC

NC

GND

Pin Signal

11 NC

12

13

-12V

GND

+5V

GND

+5 V

GND

POWER OK

+5VSB

+12V

14

15

16

17

18

19

20

PS ON

GND

GND

GND

-5V

+5V

+5V


SBC-659P

Parallel port connector (CN17)

Normally, the parallel port is used to connect the board to a printer.

The SBC-659P includes an onboard parallel port, accessed through

CN17, a 26-pin flat-cable connector. A traditional DB-25 connector cable is needed to install the printer to the board. The cable has a

26-pin connector on one end and a DB-25 pin connector on the other.

Parallel port IRQ

The onboard parallel port is designated as LPT1 and can be disabled or changed to LPT2 or LPT3 in the system BIOS setup.

Parallel port connector table (CN17)

9

10

11

7

8

5

6

12

13

2

3

4

Parallel port connector (CN17)


1

STROBE 14 AFD

PTD0

PTD1

PTD2

15

16

17

ERROR

INIT

SLIN

PTD3

PTD4

PTD5

PTD6

PTD7

ACK

BUSY

PE

SELECT

18

19

20

21

22

23

24

25

26

GND

GND

GND

GND

GND

GND

GND

GND

N.C.


BC-599/596

PS/2 keyboard and mouse connectors(CN18)

On board SBC-659P, there is a standard 6-pin mini-din connector for

PS/2 keyboard and mouse connector. The pin definition is provided below.

Keyboard and mouse connector (CN 18)

Pin

1

3

5

7

Signal

MS CLOCK 2

+5V

KB DATA

N/C

Pin

4

6

8

Signal

KB CLOCK

GND

MS DATA

N/C

IrDA Connector (CN19)

The IrDA connector (CN19) can be configured to support wireless infrared modules. With this module and application software such as laplink or Win95, Direct Cable connection can transfer files between laptops, notebooks, PDA and printers. This connector supports HPSIR ( 115.2Kbps, 2 meters ), (ASK-IR ( 56Kbps ) and fast IR (4Mbps, 2 meters).Install infrared module onto IrDAconnector and enabled infrared function from BIOS setup, make sure to have correct orientation when you plug onto IRDA connector (CN19).

4

5

6

2

3

Pin Signal

1 +5V

CIRTX

IRRX

GND

IRTX

CIRRX


SBC-659P

CPU Fan power connectors (CN20)

Plug in the fan cable to the 3-pin fan connector onboard. The fan connector is marked CN20.

2

3

CPU fan power connector (CN20)

Pin

1

Signal

GND

+12V

Fan speed sensor

North bridge chip Fan Connector (CN21)

Plug in the North Bridge chip fan cable to the 2-pin fan connector.

CPU fan power connector (CN21)with no ACPI,APM function.

Pin

1

2

Signal

GND

+12V


BC-599/596

Compact Flash Connector (CN22)

GND

GND

GND

GND

+5V

GND

GND

GND

GND

ADDR2

ADDR1

ADDR0

DATA0

DATA1

DATA2

N.C.

GND

23

24

25

19

20

21

22

13

14

15

16

9

10

11

12

17

18

Compact Flash Connector (CN22)

6

7

4

5

8

2

3

Pin Signal

1 GND

DATA3

DATA4

DATA5

DATA6

DATA7

CS#1

GND

29

30

31

32

33

Pin

26

27

28

48

49

50

44

45

46

47

38

39

40

41

34

35

36

37

42

43

Signal

GND

DATA11

DATA12

DATA13

DATA14

DATA15

CS#3

GND

IO READ

IO WRITE

+5V

IRQ15

+5V

CSEL

N.C.

IDE RESET

IO READY

N.C.

+5V

DASP

DIAG

DATA8

DATA9

DATA10

GND



3

Award BIOS Setup

This chapter describes how to configure the BIOS for the system.

Starting setup

The Award BIOS is immediately activated when you first turn on the computer. The BIOS reads system configuration information in

CMOS RAM and begins the process of checking out the system and configuring it through the power-on self test (POST).

When these preliminaries are finished, the BIOS seeks an operating system on one of the data storage devices (hard drive, floppy drive, etc.). The BIOS launches the operating system and hands control of system operations to it.

During POST, you can start the Setup program in one of two ways:

1.By pressing Del immediately after switching the system on, or

2.By pressing Del or pressing Ctrl-Alt-Esc when the following message appears briefly at the bottom of the screen during POST:

TO ENTER SETUP BEFORE BOOT PRESS DEL KEY

If the message disappears before you respond and you still wish to enter Setup, restart the system to try again by turning it OFF then

ON or pressing the RESET button on the system case. You may also restart by simultaneously pressing Ctr-Alt-Del. If you do not press the keys at the correct time and the system does not boot, an error message appears and you are again asked to

PRESS F1 TO CONTINUE, DEL TO ENTER SETUP

Chapter 3 Award BIOS Setup 39

Setup keys

These keys helps you navigate in Award BIOS:

Up arrow

Down arrow

Left arrow

Right arrow

Move to previous item

Move to next item

Move to the item in the left hand

Move to the item in the right hand

F2

F3

F4

F5

Esc Main Menu: Quit and not save changes into

CMOS RAM

Other pages: Exit current page and return to

Main Menu

PgUP/+

PgDn/-

Increase the numeric value or make changes

Decrease the numeric value or make changes

F1

F6

F7

F8

F9

F10

General help, only for Status Page Setup

Menu and Option Page Setup Menu

Item Help

Reserved

Reserved

Restore the previous CMOS value from

CMOS, only for Option Page Setup Menu

Load the default CMOS RAM value from

BIOS default table, only for Option Page

Setup Menu

Load the default

Reserved

Reserved

Save all the CMOS changes, only for Main

Menu


Getting Help

Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press Esc or the F1 key again.

In Case of Problems

If, after making and saving system changes with Setup, you discover that your computer no longer is able to boot, the Award

BIOS supports an override to the CMOS settings that resets your system to its default configuration.

You can invoke this override by immediately pressing Insert; when you restart your computer. You can restart by either using the ON/

OFF switch, the RESET button or by pressing Ctrl-Alt-Delete.

The best advice is to alter only settings that you thoroughly understand. In particular, do not change settings in the Chipset screen without a good reason. The Chipset defaults have been carefully chosen by Award Software or your system manufacturer for the best performance and reliability. Even a seemingly small change to the Chipset setup may cause the system to become unstable.


Main Setup Menu

Standard CMOS Features

Use this menu for basic system configuration. (Date, time, IDE, etc.)

Advanced BIOS Features

Use this menu to set the advanced features available on your system.

Advanced Chipset Features

Use this menu to change the values in the chipset registers and optimize your system’s performance.

Integrated Peripherals

Use this menu to specify your settings for integrated peripherals.

(Primary slave, secondary slave, keyboard, mouse etc.)

Power Management Setup

Use this menu to specify your settings for power management.

(HDD power down, power on by ring, KB wake up, etc.)


PnP/PCI Configuration

This entry appears is your system supports PnP/PCI.

PC Health Status

This menu allows you to set the shutdown temperature for your system.

Frequency/Voltage Control

Use this menu to specify your settings for frequency/ voltage control.

Load Fail-Safe Defaults

Use this menu to load the BIOS default values for the minimal/ stable performance for your system to operate.

Load Optimized Defaults

Use this menu to load the BIOS default values that are factory settings for optimal performance system operations. While

AWARD has designated the custom BIOS to maximize performance, the factory has the right to change these defaults to meet their needs.

Set Supervisor/User Password

Use this menu to set User and Supervisor Passwords.

Save and Exit Setup

Save CMOS value changes to CMOS and exit setup.

Exit Without Saving

Abandon all CMOS value changes and exit setup.


Standard CMOS Features

This standard setup menu allows users to configure system components such as the date, time, hard disk drive, floppy drive, display, and memory. Online help for each field can be accessed by pressing F1.

Date and Time Configuration

The BIOS determines the day of the week from the other date information. This field is for information only.

Press the left or right arrow key to move to the desired field (date, month, year). Press the PgUp/- or PgDn/+ key to increment the setting, or type the desired value into the field.

The time format is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00 hours. Press the left or right arrow key to move to the desired field. Press the PgUp/- or PgDn/+ key to increment the setting, or type the desired value into the field.

HARD DISKS

The BIOS supports up to four IDE drives. This section does not show information about other IDE devices, such as a CD-ROM drive, or about other hard drive types, such as SCSI drives.

NOTE: We recommend that you select type AUTO for all drives.


The BIOS can automatically detect the specifications and optimal operating mode of almost all IDE hard drives. When you select type AUTO for a hard drive, the BIOS detects its specifications

If you do not want to select drive type AUTO, other methods of selecting the drive type are available:

1.Match the specifications of your installed IDE hard drive(s) with

the preprogrammed values for drive types 1 through 45.

2.Select USER and enter values into each drive parameter field.

3.Use the IDE HDD AUTO DETECTION function in Setup.

Here is a brief explanation of drive specifications:

Type:

The BIOS contains a table of predefined drive types. Each

defined drive type has a specified number of cylinders,

number of heads, write precompensation factor, landing

zone, and number of sectors. Drives whose specifications

do not accommodate any predefined type are classified as

type USER.

Size

: Disk drive capacity (approximate). Note that this size is

usually slightly greater than the size of a formatted disk

given by a disk-checking program.

Cyls

: Number of cylinders

Head

: Number of heads

Precomp

: Write precompensation cylinder

Landz

: Landing zone

Sector

: Number of sectors

Mode

: Auto, Normal, Large, or LBA

- Auto

: The BIOS automatically determines the optimal mode.

- Normal

: Maximum number of cylinders, heads, and sectors

supported are 1024, 16, and 63.

- Large

: For drives that do not support LBA and have more

than 1024 cylinders.


- LBA

(Logical Block Addressing): During drive access, the

IDE controller transforms the data address described by sector, head, and cylinder number into a physical block address, significantly improving data transfer rates. For drives with greater than 1024 cylinders.

Drive A

Drive B

Select the correct specifications for the diskette drive(s) installed in the computer.

None No diskette drive installed

360K, 5.25 in 5-1/4 inch PC-type standard drive;

360 kilobyte capacity

1.2M, 5.25 in 5-1/4 inch AT-type high-density drive; 1.2 megabyte capacity

720K, 3.5 in 3-1/2 inch double-sided drive;

720 kilobyte capacity

1.44M, 3.5 in 3-1/2 inch double-sided drive;

1.44 mega byte capacity

2.88M, 3.5 in 3-1/2 inch double-sided drive;

2.88 mega byte capacity


Halt On

During the power-on-self-test (POST), the computer stops if the

BIOS detects a hardware error. You can tell the BIOS to ignore certain errors during POST and continue the boot-up process.

These are the selections:

No errors

: POST does not stop for any errors.

All errors If

: the BIOS detects any nonfatal error, POST stops and prompts you to take corrective action.

All, But Keyboard

: POST does not stop for a keyboard error, but stops for all other errors

All, But Diskette

: POST does not stop for diskette drive errors, but stops for all other errors.

All, But Disk/Key

: POST does not stop for a keyboard or disk error, but stops for all other errors.

Memory

You cannot change any values in the Memory fields; they are only for your information. The fields show the total installed random access memory (RAM) and amounts allocated to base memory, extended memory, and other (high) memory. RAM is counted in kilobytes (KB: approximately one thousand bytes) and megabytes

(MB: approximately one million bytes).

RAM is the computer's working memory, where the computer stores programs and data currently being used, so they are accessible to the CPU. Modern personal computers may contain up to 64

MB, 128 MB, or more.

Base Memory

Typically 640 KB. Also called conventional memory. The DOS operating system and conventional applications use this area.


Extended Memory

Above the 1-MB boundary. Early IBM personal computers could not use memory above 1 MB, but current PCs and their software can use extended memory.

Other Memory

Between 640 KB and 1 MB; often called High memory. DOS may load, terminate-and-stay-resident (TSR) programs, such as device drivers, in this area, to free as much conventional memory as possible for applications. Lines in your CONFIG.SYS file that start with LOADHIGH, load programs into high memory.


Advanced BIOS Features

The displayed configuration is based on the manufacturer's SETUP

DEFAULTS settings.

Virus Warning

When enabled, you receive a warning message if a program

(specifically, a virus) attempts to write to the boot sector or the partition table of the hard disk drive. You should then run an antivirus program. Keep in mind that this feature protects only the boot sector, not the entire hard drive.

NOTE: Many disk diagnostic programs that access the boot sector table can trigger the virus warning message. If you plan to run such a program, we recommend that you first disable the virus warning.


CPU Internal Cache/External Cache

Cache memory is additional memory that is much faster than conventional DRAM (system memory). CPUs from 486-type on up contain internal cache memory, and most, but not all, modern PCs have additional (external) cache memory. When the CPU requests data, the system transfers the requested data from the main DRAM into cache memory, for even faster access by the CPU.

The External Cache field may not appear if your system does not have external cache memory.

CPU L2 Cache ECC Checking

When you select Enabled, memory checking is enable when the external cache contains ECC SRAMs.

Processor Number Feature

This option is for Pentium III processor. During Enabled, this will check the CPU Serial number. Disabled this option if you don't want the system to know the serial number.

Quick Power On Self Test

Select Enabled to reduce the amount of time required to run the power-on-self-test (POST). A quick POST skips certain steps. We recommend that you normally disable quick POST. Better to find a problem during POST than lose data during your work.

First/Second/Third/Fourth Boot Device

The BIOS attempts to load the operating system from the devices in the sequence selected in these items.

The choices: Floppy, LS/ZIP, HDD, SCSI, CDROM, Disable.


Swap Floppy Drive

This field is effective only in systems with two floppy drives.

Selecting enabled assigns physical drive B to logical drive A, and physical drive A to logical drive B.

Boot Up Floppy Seek

When Enabled, the BIOS tests (seeks) floppy drives to determine whether they have 40 or 80 tracks. Only 360-KB floppy drives have 40 tracks; drives with 720 KB, 1.2 MB, and 1.44 MB capacity all have 80 tracks. Because very few modern PCs have

40-track floppy drives, we recommend that you set this field to

Disabled to save time.

Boot Up NumLock Status

Toggle between On or Off to control the state of the NumLock key when the system boots. When toggled On, the numeric keypad generates numbers instead of controlling cursor operations.

Boot Up System Speed

Select High to boot at the default CPU speed; select Low to boot at the speed of the AT bus. Some add-in peripherals or old software

(such as old games) may require a slow CPU speed. The default setting is High.

Gate A20 Option

Gate A20 refers to the way the system addresses memory above 1

MB (extended memory). When set to Fast, the system chipset controls Gate A20. When set to Normal, a pin in the keyboard controller controls Gate A20. Setting Gate A20 to Fast improves system speed, particularly with OS/2 and Windows.


Typematic Rate Setting-

Key strokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected.

The choice: Enabled/Disabled

Typematic Rate (Chars/Sec)-

Sets the number of times a second to repeat a key stroke when you hold the key down.

The choice: 6, 8, 10, 12, 15, 20, 24, 30

Typematic Delay (Msec)-

Sets the delay time after the key is held down before it begins to repeat the keystroke.

The choice: 250, 500, 750, 1000

Security Option

If you have set a password, select whether the password

is required every time the System boots, or only when you enter

Setup.

OS Select For DRAM>64MB-

Select the operating system that is running with greater than 64MB or RAM on the system.

The choice: Non-OS2, OS2


HDD S.M.A.R.T Capability

Hard disk drives have built in problem detection capability (Self-Monitoring Analysis and Reporting Technology).

If a foreseen problem is about to take place, the computer will give a you a warning signal. The choice: Enable, Disable

Report No FDD For WIN 95-

Report no FDD for Win 95 or not. The choice: Yes, no

EPA Logo Select

the choic: Log1,Logo2

Small Logo(EPA) show

the choice:enable,disable


Advanced Chipset Features

SDRAM CAS Latency Time

When synchronous DRAM is installed, the number of clock cycles of

CAS latency depends on the DRAM timing. Do not reset this field from the default value specified by the system designer.

SDRAM Cycle Time Tras/Trc

Select the number of SCLKs for an access cycle.

The choices: 5/7, 7/9 disable.

SDRAM RAS-to-CAS Delay

This field lets you insert a timing delay between the CAS and RAS strobe signals, used when DRAM is written to, read from, or refreshed. Fast gives faster performance; slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system.


SDRAM RAS Precharge Time

If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete and the

DRAM may fail to retain date. Fast gives faster performance; slow gives more stable performance. This field applies only when synchronous

DRAM is installed in the system.

System BIOS Cacheable

Selecting Enabled allows caching of the system BIOS ROM at F0000h-

FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The choices:

Enabled, Disabled

Video BIOS Cacheable

Selecting Enabled allows caching of the video BIOS ROM at C0000h to

C7FFFh, resulting in better video performance. However, if any program writes to this memory area, a system error may result. The choices:

Enabled, Disabled Memory

Memory Hole At 15-16m

In order to improve performance, certain space in memory is reserved for

ISA cards. This memory must be mapped into the memory. The choices:

15-16 M, disabled

CPU Latency Timer

During enable, a deferrable CPU cycle will only be Deferred after it has been in Snoop Stall for 31 clocks and another ADS# has arrived. During disable, a deferrable CPU cycle will be deferred immediately after the

GMCH receives another ADS#.

Delayed Transaction

The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2.1.


AGP Graphics Aperture Size

Select the size of Accelerated Graphics Port (AGP) aperture. The aperture is a portion of the PCI memory address range dedicated for graphics memory address space. Host cycles that hit the aperture range are forwarded to the AGP without any translation. The choices: 32M,

64M.

Display Cache Frequency

You can use this item to selct the frequency of the display cache.

The choice: 100 MHz,133 MHz

System Memory Frequency

You can use this item to select the operating frequency for the main system memory. The choice: Auto,100 MHz, 133 MHz

On-Chip Video Window Size

Select the on-chip video window size for VGA drive use.

The choices: 32MB, 64MB, Disabled

*On board Display Cache Setting*

CAS Latency

Select the local memory clock periods. The choice:2,3

Paging Mode Control

Select the paging mode control. The choice:close,open


RAS-to-CAS Override

Select the display cache clock periods control.

The choice:Fast,Slow

RAS#Timing

This item controls RAS#active to Protegra, and refresh to RAS# active delay(in local memory clocks),

RAS#Percharge Timing

This item controls RAS#precharge(in local memory clocks).

The choice: Fast,Slow.


Integrated Peripherals

On-Chip Primary PCI IDE

The system chipset contains a PCI IDE interface with support for two IDE channels. Select Enabled to activate the primary and/or secondary IDE interface. Select Disabled to deactivate this interface, if you install a primary and/or secondary add-in IDE interface.

On-Chip Secondary PCI IDE

The chipset contains a PCI IDE interface with support for two IDE channels. Select Enabled to activate the secondary IDE interface.

Select Disabled to deactivate this interface.

The choices: Enable, Disable

IDE Primary/Secondary Master/Slave PIO

The four IDE PIO (Programmable Input/Output) fields let you set a

PIO mode (0-1) for each of the four IDE devices that the onboard

IDE interface supports. Modes 0 through 4 provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device.

The choices: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode 4.


IDE Primary/Secondary Master/Slave UDMA

Ultra DMA/33 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus master driver).

If your hard drive and your system software both support Ultra

DMA/33, select Auto to enable BIOS support.

The choices: Auto, disable

USB Controller

Select Enabled if your system contains a Universal Serial Bus controller and you have USB peripherals.

USB Keyboard Support

Select Enabled if your system contains a Universal Serial Bus controller and you have a USB keyboard.

USB Mouse Support

Select Enabled if your system contains a Universal Serial Bus controller and you have a USB mouse.

Init Display First

This item allows you to active PCI slot or onboard first.

The choice: PCI slot, onboard

AC97 Audio

The default setting of Auto enables the AC97 audio if it is detected onboard

IDE HDD Block Mode

Select Enabled only if your hard drives support block mode.

Power on Function

Select the different manners for powering on the system.

The choices: Keyboard 98, password, any key, hot key, button only, mouse click, mouse move.


KB Power on Password

The system will ask for a password, after entering the correct password the keyboard can then be used.

Hot Key Power On

Simply pressing on the pre-selected keyboard key the system will power on.

Onboard FDC Controller

Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you install an add-in FDC or the system has no floppy drive, select Disabled in this field.

UART Mode Select

Select an operating mode for the second serial port:

Normal RS-232C serial port

IrDA 1.0

IrDA SIR

IrDA MIR

Infrared port compliant with IrDA 1.0

specification

IrDA-compliant serial infrared port

1 MB/sec infrared port

IrDA FIR

ASK IR

SCR

Fast infrared standard

Amplitude shift keyed infrared port


Onboard Serial Ports (1, 2)

Normally, the main board’s I/O chips will occupy a certain portion of memory space. For each I/O device the computer provides an

I/O address. The more devices attached the more address needed to organize the memory storage areas. If all the I/O devices were run through the same address, your devices would come to a near halt. By providing the end user with four serial ports this allows devices to run more efficiently if needed. Also the corresponding interrupt needs to be selected.

Selections of logical COM port addresses are as follows. ( 3F8/

IRQ4, 3E8/IRQ4, 2F8/IRQ3, 2E8/IRQ3)

Onboard Parallel Port

Select a logical LPT port address and corresponding interrupt for the physical parallel port

The Choice: 378/IRQ7, 278/IRQ5, 3BC/IRQ7, disabled

Parallel Port Mode

Two bidirectional parallel ports. Supports SPP, ECP, EPP,

ECP + EPP.

ECP Mode Use DMA

Select a DMA channel for the port.

PWRON After PWR-Fail

This option will determine how the system will power on after a power failure.

The choice: off, on , former status


Watch Dog Timer

You can enable the system watchdog timer, a hardware timer that generates either an NMI or a reset when the software that it monitors does not respond as expected each time the watch dog polls it ( select the time period in a separate field ) The choice:

Disabled, 10 sec, 20 sec, 30 sec, 40 sec, 1 min, 2 min, 4 min.


Power Management Setup

ACPI Function

This item allows you to enable/disable the Advanced Configuration and Power Management (ACPI). The Choices: Enable/Disable


Power Management

This category allows you to select the type ( or degree ) of power saving and is directly related to the following modes:

1. HDD Power Down

2. Doze Mode

3. Suspend Mode

D i s a b l e ( D e f a u l t )

M i n .

P o w e r S a v i n g

M a x .

P o w e r S a v i n g

U s e r D e f i n e d

N o p o w e r m a n a g e m e n t .

D i s a b l e a l l f o u r m o d e s .

M i n h o u r i m

.

u m p o w

S t a n d b y e r m m a o d n a e g e

= 1 m e h n .

o u r

D

.

o z e

S u s p m o d e e n d

= 1 m o d e

1 h o u r .

H D D P o w e r D o w n = 1 5 m i n u t e s .

=

M a x i m u m p o w e r m a n a g e m e n t O N L Y

A V A I L

1 m i n .

,

A B L E

S t a n d b y

F O R m o d e

S L

=

C P U ' S .

1 m i n .

,

D o

S u s s p e e n m o d e d

= m o d e

= 1 m i n .

, a n d H D D P o w e r D o w n = 1 m i n .

A l n o l o t w s y o u d i s a b l e d , t o s e t e a c h e a o f c h t h e m o d e t a n g e i n s d a i v r i d u a l l y .

e f r o m

W h e

1 m i n .

n t o r a

1 n g e h o s u f r r o e m x c e

1 p t m i f o r n .

t o

H D D

1 5 m

P o w e r i n .

a n d

D o w n w h i c h d i s a b l e .

Video Off Method

This determines the manner in which the monitor is blanked.

V / H S Y N C + B l a n k

B l a n k S c r e e n

D P M S

T h i s t h e s e l e c t i o n w v e r t i c a l a n d i h l l o c a u s e r i z o n t a t l h e s y s t e m t o t u r s y n c h r o n i z a t i o n n o f f p o r t s a n d w r i t e b l a n k s t o t h e v i d e o b u f f e r

T h i s o p t i o n o n l y w r i t e s b l a n k s t o t h e v i d e o b u f f e r

I n i t i a l d i s p l a y p o w e r m a n a g e m e n t s i g n a l i n g


Video Off In Suspend

After the selected period of system inactivity, the chipset enters a hardware suspend mode, stopping the CPU clock and possibly causing other system devices to enter power management modes.

In this case the video hardware can be selected to shut off after a period of system inactivity. This determines the manner in which the monitor is blanked.

Suspend Type

Select the suspend type. The choice: PWRON suspend, Stop

Grant

MODEM use IRQ

This determines the IRQ in which the MODEM can use.

The choices: 3, 4, 5, 7, 9, 10, 11, NA

Suspend Mode

After the selected period of system inactivity, the chipset enters a hardware suspend mode, stopping the CPU clock and possibly causing other system devices to enter power management modes.

HDD Power Down

After the selected period of drive inactivity, the HDD powers down while all other devices remain active.

Soft-Off by PWR-BTTN

Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state when the system has hung. The choice: Delay 4 seconds, Instant-Off.

Wake Up On Lan

The board enabled or disabled will execute a wake up process whenever LAN (Intel 815E) receives a wake up event such as a magic packet.

The Choice: Disabled, Enabled


Power On By Ring

An input signal on the serial Ring Indicator (RI) line (in other words, an incoming call on the modem) boots the system from a soft off state.

Resume By Alarm

This option is used to Enable/Disable USB keyboard wake up with suspend to RAM.

The choices: Enable, disable

Date Alarm

You can choose which month the system will boot up. Set to 0 to boot everyday.

Time Alarm

You can choose what hour, minute and second the system will boot up.

<Reload Global Timer Events>

PM events are I/O events whose occurrence can prevent the system from entering a power saving mode or can awaken the system from such a mode. In effect, the system remains alert for anything which occurs to a device which is configured as Enabled, even when the system is in a power down mode.

Primary IDE 0

Primary IDE 1

Secondary IDE 0

Secondary IDE 1

FDD, COM, LPT Port

PCI PIRQ (A-D)#


PnP/PCI Configurations

PnP OS installed

This item allows you to determine install PNP OS or not.

The choice: Yes,No

Reset Configuration Data

Normally, you leave this field disabled. Select enabled to reset

Extended System Configuration Data (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the operating system can not boot. The choices: Enabled, Disabled


Resources Controlled By

The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices.

However, this capability means absolutely nothing unless you are using a Plug and Play operating system such as Windows ® 95. If you set this field to “manual” choose specific resources by going into each of the sub menu that follows this field ( a sub menu is proceeded by a “>”. The choices: Auto, Manual.

IRQ Resources

When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt.

DMA Resources

This sub menu can let you control the DMA resource.

PCI/VGA Palette Snoop

Leave this field at Disabled. Choices: Enabled, Disabled.

Lan 1 Controller For 82559

Operation controller for 82559 Lan. You may choose to enable or disable this function.

Lan 2 Controller For 82559

Operation controller for 82559 Lan. You may choose to enable or disable this function.


PC Health Status

Shutdown Temperature

Your system can be configured to shutdown once reaching a certain temperature. To protect your system from overheating or damage, select a certain temperature level in the PC Health Status menu.


Frequency/Voltage Control

Auto Detect DIMM/PCI CLK

This item allows you to enable/disable auto detect DIMM/PCI clock. The choices: Enable/Disable

Spread Spectrum

This allows you to enable/disable the spread spectrum modulate.

When the system clock generator pulses, the extreme values of the pulse generate excess EMI. Enabling pulse spectrum spread modulation changes the extreme pulse spikes to flat curves thus reducing EMI.

The choices: Enable, Disable

Clock By Slight Adjust

This item allows you to select the CPU clock from 166 MHz to

100 MHz or 99 MHz to 66 MHz depending on the CPU host clock.

CPU Clock Ratio

This item allows you to select the CPU ratio.




When you press <Enter> on this item you get a confirmation dialog box with a message similar to:

Load Fail-Safe Default (Y/N)?

Pressing “Y” loads the BIOS default values for the most stable, minimal performance system operations.


Load Optimized Default

Load Optimized Default

When you press <Enter> on this item you get a confirmation dialog box with a message similar to:

Load Optimized Defaults (Y/N)?

Pressing “Y” loads the default values that are factory settings for optimal performance system operations


Set Supervisor Password

When you select this function, a message appears at the center of the screen:

ENTER PASSWORD:

Type the password, up to eight characters, and press Enter. Typing a password clears any previously entered password from CMOS memory.

Now the message changes:

CONFIRM PASSWORD:

Again, type the password and press Enter.

To abort the process at any time, press Esc.

In the Security Option item in the BIOS Features Setup screen, select System or Setup:

System Enter a password each time the system boots and when

ever you enter Setup.

Setup Enter a password when ever you enter Setup.

NOTE: To clear the password, simply press Enter when asked to enter a password. Then the password function is disabled.


Set User Password

When you select this function, a message appears at the center of the screen:

ENTER PASSWORD:

Type the password, up to eight characters, and press Enter. Typing a password clears any previously entered password from CMOS memory.

Now the message changes:

CONFIRM PASSWORD:

Again, type the password and press Enter.

To abort the process at any time, press Esc.

In the Security Option item in the BIOS Features Setup screen, select System or Setup:

System Enter a password each time the system boots and when

ever you enter Setup.

Setup Enter a password when ever you enter Setup.

NOTE: To clear the password, simply press Enter when asked to enter a password. Then the password function is disabled.


Save to CMOS and EXIT

Save to CMOS and EXIT

Pressing <Enter> on this item asks for confirmation:

Save to CMOS and Exit (Y/N)?

Pressing “Y” stores the selections made in the menus in CMOS, a special section of memory that stays on after you turn your system off. The next time you boot your computer, the BIOS configures your system according to the Setup selections stored in CMOS.

After saving the values the system is restarted again.


Exit without Saving

Exit Without Saving

Pressing <Enter> on this item asks for confirmation:

Quit Without Saving (Y/N)?

This allows you to exit Setup without storing in CMOS any change.

The previous selections remain in effect. This exits the Setup utility and restarts your computer.


DRIVERS INSTALLATION

4

This SBC-659P is equipped with an audio,

VGA and Dual LAN interface. This chapter provides

instructions for installing the software drivers on these pheripherals.


Installing Drivers

Notice: Attention

First if using operating systems such as Windows

95/98/2000 ® a chipset driver must be installed before

VGA, LAN or Audio drivers are installed.

Second if using Windows 95/98/2000® operating systems an Ultra ATA storage driver must also be installed after the chipset driver.


Installing Chipset Driver for Windows 95/98/

2000®

The chipset driver must be installed in order to proceed to LAN, VGA and AUDIO drivers.

==>Place the Driver CDROM into your CDROM drive. Pull up the CDROM file on your screen.

==>Find the Chipset folder, click on it

==>Find the Intel folder, click on it

==>Find the InfUpdate folder, click on it

==>Find the InfInst folder, click on it

==>Find the Win9X & Win2K folder, click on it

==>Find the Setup ICON, and double click

==>Click on Next

==>Click on Yes


==>Now the shut down computer for restart should be visible, follow the command and the chipset driver has be installed.


Installing Ultra ATA Storage Driver for Windows 95/98/

2000®

The Ultra ATA Storage Driver must be installed in order to use Windows 95/98/2000 ® operating systems.


==>Find the MB folder, click on it

==>Find the intel ATA 603_Multi folder, click on it


==>Click on Yes

==>Select the optional: Select storage folder where to store Ultra

ATA



==>Now the shut down computer for restart Window should be visible, follow the command and the chipset driver has be installed.


Installing Intel 82559 for Windows 95 or 98 Ver.

1.0®

==>Place the Driver CDROM into your CDROM drive.

==>Click on Start button

==>Click on Settings button

==>Click on Control Panel button

==>Click on System button

==>Click on Device Manager button

==>Click on PCI Ethernet Controller

==>Click on Remove

==>Click on OK

==>Click on Refresh


==>Select the Optional: Other Location.....

==>Click on Browse

==>Select CDROM file

==>Select Next

==>Click on OK

==>Click on Finish

==>Then you will be asked to confirm the location of the select

file....



Installing VGA for Windows 95/98®

==>Place the Driver CDROM into your CDROM drive. Pull up the CDROM file on your screen..

==>Click on Intel folder

==>Click on 810_815 folder

==>Click on Win9X folder

==>Click on Graphics folder

==>Click on Set Up folder


==>Click on yes


Caution:Installing VGA driver may under Windows 95 may apper following error message.

Our driver CD-ROM provide DCOM file,install it first.Then the error will not appear next time.

’ ’


Installing Audio for Windows 95/98®


==>Click on Sound folder

==>Click on Alc 200 folder

==>Click on Win98 folder

==>Click on V1.80 folder

==>Click on WDM_1 folder

==>Next you will be asked to save this WDM file in a certain location. C drive, D drive, My docuements etc.

==>Click on Unzip

==>Click on OK

==>Now find the WDM file that you have just saved. C drive, D drive etc.

==>Click on WDM file in the save location

==>Click on the Setup ICON

==>You will see an optional language window

==>Click on OK


==>Click on OK

==>Click on GO



Installing Security Driver for Windows

NT®

Please perform this procedure first


==>Click on Chipset folder


==>Click on Security folder

==>Click on Setup folder


==>Click on Yes

==>Click on Next


==>Now the shut down computer for restart Window should be visible, follow the command and the Security driver has be installed.


Installing Ultra ATA Storage Driver for Windows

NT®

The Ultra ATA Storage Driver must be installed in order to use Windows NT ® operating systems.


==>Find the MB folder, click on it

==>Find the intel ATA 603_Multi folder, click on it


==>Click on Yes

==>Select the optional: Select storage folder where to store Ultra

ATA





Installing VGA for Windows NT®


==>Click on VGA folder



==>Click on NT4 folder

==>Click on Graphics folder



==>Click on yes



Installing Audio for Windows NT®




==>Click on WinNT folder


==>Click on WDM_1



==>Click on OK




==>You will see an optional language window select English

==>Click on OK




Installing Intel 82559 for Windows NT®

==>Place the Driver CDROM into your CDROM drive.

==>Click on Start button

==>Click on Settings button

==>Click on Control Panel button

==>Click on Network

==>Click on yes

==>Click on next

==>Click on Select from list.......

==>Click on have disk

==>Type in file location: (CD Disk drive) E:\CDROM

==>Click on OK

==>Intel Pro Adapter will appear

==>Click on OK




==>Click on Next



Installing VGA for Windows 2000®


==>Click on VGA folder




==>Click on 815 folder



==>Click on yes


==>Click on yes



Installing Audio for Windows 2000®






==>Click on WDM_1 folder






==>You will see an optional language window select English


==>Click on GO

==>Click on Yes



IBM SBC-659P User's Manual

Copyright Notice

Acknowledgments

A Message to the Customer

Packing list

Notice

Http:\\WWW.AAEON.COM

Contents

General

Information

Introduction

Features

Specifications

Board Layout

Board Dimensions

Installation

Safety precautions

Removing the CPU

Installing A CPU

Setting jumpers

Installing SODIMM

Jumpers

Connectors

Locating Jumpers and Connectors

Locating of Solder Side Connectors

Mechanical Drawing

Mechanical Drawing

Clear CMOS (JP2)

Front Panel (JP1)

System Frequency (JP3)

COM2 (Ring, +5V, +12V) JP4

RS-232/422/485 COM2(JP5,JP6) Setting

Digital Video Output Connector (CN1)

External Power On Connector (CN2)

IDE Hard Drive Connector (CN3)

USB connector (CN5, CN6)

Floppy Drive Connector (CN7)

VGA connector (CN8)

Audio Connector (CN9)

Ethernet Connectors(CN12,CN10)

COM 1 (CN 13) & COM 2 (CN 11) Serial Ports

Internal Keyboard Connector (CN15)

Power connector (CN16)

Parallel port connector (CN17)

PS/2 keyboard and mouse connectors(CN18)

IrDA Connector (CN19)

CPU Fan power connectors (CN20)

North bridge chip Fan Connector (CN21)

Compact Flash Connector (CN22)

Award BIOS Setup

Starting setup

Setup keys

Getting Help

Main Setup Menu

Standard CMOS Features

Advanced BIOS Features

Advanced Chipset Features

Integrated Peripherals

Power Management Setup

PnP/PCI Configuration

PC Health Status

Frequency/Voltage Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor/User Password

Save and Exit Setup

Exit Without Saving

Standard CMOS Features

Date and Time Configuration

HARD DISKS

Type:

Size

Cyls

Head

Precomp

Landz

Sector

Mode

- Auto

- Normal

On board Display Cache Setting