Installation Guide
IDE-16052
AAAA AAAA AA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A A
AAAA AAAA AA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA A A
AA
AA
IDE-16052 Installation Guide
A
A
AA
AA
AA
Part Number: 510999-00, Rev. B
AA
AA
Print Spec Number: 494453-00
AA
AA
AA
Current Date: 4/29/96
AA
ECN Date: 5/7/96
A
A
A
A
A
A
A
A
A
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA
Description
The Future Domain® IDE-16052 is a low-cost, multifunction host adapter for ISA-bus computers. This dual-channel, double-word (32-bit), Enhanced IDE
(EIDE) host adapter contains an onboard BIOS that enables you to boot from hard drives and identify all
IDE peripheral devices without additional software.
The IDE-16052 provides dual EIDE channels that support up to four IDE (ATA) devices and high-performance double-word (32-bit data transfers) plus:
■
■
■
A floppy controller that supports two floppy disk drives, each with a capacity of up to 2.88MBytes
A high-performance parallel port with standard parallel port (SPP), enhanced parallel port (EPP), and enhanced capabilities port (ECP) modes
Two high-speed serial ports (16550-compatible
UARTs)
The IDE-16052 host adapter is ideal for users who need affordable compatibility for their EIDE devices and high-performance connectivity to the outside world.
Configuration
The IDE-16052 host adapter shown in the following illustration occupies one 16-bit ISA-bus expansion slot.
SW1 J3 J4 SW2 J6 J9
J2 JP1
JP2
JP5
JP6
1
A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA A AAAA
A
A
IDE-16052 Installation Guide
AA
AA
A
A
A
Part Number: 510999-00, Rev. B
A
A
Print Spec Number: 494453-00
A
A
A
Current Date: 4/29/96
A
ECN Date: 5/7/96
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A
J10
Location
SW1
J3
J4
SW2
J6
J9
J10
JP1, JP2, JP5, JP6
J2
Description
Switch block 1
IDE-A (Primary IDE channel A)
IDE-B (Secondary IDE channel B)
Switch block 2
COM2/COM4 (Serial port)
COM1/COM3 (Serial port)
LPT 1/LPT 2 (Parallel port)
IRQ/DMA jumpers
Floppy port
Attach IDE/ATA devices to host adapter connectors
J3 and J4 via an HCA-302 data cable. (See the following illustration.) One data cable is required for each
IDE channel. You may attach up to two IDE devices to each data cable. If you attach only one IDE/ATA device to a data cable, you must connect that device to the end of the cable.
Attach floppy drives to host adapter connector J2 via an HCA-105 floppy cable. (See the following illustration.) Install floppy device 0 (3.5- or 5.25-inch) at the end of the cable. Install floppy device 1 (3.5- or
5.25-inch) in the middle of the cable.
Pin 40
HCA-302 data cable
HCA-105 floppy cable
Pin 1
(red stripe)
Pin 34
Pin 1
(red stripe)
2
A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA A AAAA
A
A
IDE-16052 Installation Guide
AA
AA
A
A
A
Part Number: 510999-00, Rev. B
A
A
Print Spec Number: 494453-00
A
A
A
Current Date: 4/29/96
A
ECN Date: 5/7/96
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A
Attach the first serial device to external connector J9 on the host adapter. Attach the second serial device to external connector J7 on the HCA-138 serial bracket, which is supplied with the IDE-16052. (See the following illustration.) For instructions on installing the HCA-138 serial bracket, see step 6 on page 8.
J7
HCA-138 serial bracket
BIOS Memory Address
The IDE-16052 host adapter contains an advanced
BIOS that supports hard drives larger than
528 MBytes and bootability from either IDE channel.
In order to enable the advanced BIOS, you must set
SW1, switch 8 (BIOS) down. The following figure illustrates a switch block and its up (0) and down (1) settings.
Down (1)
Up (0)
Use SW1, switches 4 (MEM-2), 5 (MEM-1), and
6 (MEM-0) to set the memory address for the host
adapter BIOS. These switches allow you to avoid conflicts with either the system BIOS or with other add-in cards by changing the assigned BIOS address.
3
A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA A AAAA
A
A
IDE-16052 Installation Guide
AA
AA
A
A
A
Part Number: 510999-00, Rev. B
A
A
Print Spec Number: 494453-00
A
A
A
Current Date: 4/29/96
A
ECN Date: 5/7/96
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A
IDE Channels
The IDE-16052 has two IDE channels—primary
IDE-A (J3) and secondary IDE-B (J4)—which support up to four IDE devices.
Use SW1, switches 1 (IOS-1) and 2 (IOS-0) to set the
I/O ports. Set SW1, switch 7 down to enable the
IDE-A channel. Set SW1, switch 3 down to enable the
IDE-B channel.
Note:
I/O ports and IRQs are grouped in pairs.
You can attach the boot drive to the primary or secondary IDE channel. The hard drive boot sequence is
1F0h, 170h, 168h, 1E8h.
Note:
The system BIOS (CMOS defaults) is typically set to control the primary IDE channel. In order to use the IDE-16052 host adapter BIOS, you must set the
Hard Drive Type in the system CMOS Setup to Not
Installed
4
A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA A AAAA
A
A
IDE-16052 Installation Guide
AA
AA
A
A
A
Part Number: 510999-00, Rev. B
A
A
Print Spec Number: 494453-00
A
A
A
Current Date: 4/29/96
A
ECN Date: 5/7/96
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A
Floppy Port
Use SW2, switch 8 (FLOPPY) to enable or disable the floppy port. Set SW2, switch 8 up to disable the floppy port; set switch 8 down to enable the floppy port.
Floppy Port
Disable
Enable*
* Default setting; 0 = up; 1 = down
FLOPPY
0
1
Note:
The primary floppy port address is 3F0h–
3F7h. You cannot have two floppy controllers enabled at the same time. For example, you cannot enable both the floppy controller on the motherboard and the floppy controller on the IDE-16052.
Parallel Port
The IDE-16052 has one parallel port, which you can configure as LPT 1 or LPT 2. Use SW2, switches 1
(MODE-1), 2 (MODE-2), and 3 (LPT1/2) and jumpers JP1, JP2, JP5, and JP6 to configure the parallel port.
Parallel Port
LPT 1*
LPT 2
* Default setting; 0 = up; 1 = down
LPT 1/2
1
0
Parallel Port Transfer Mode
The IDE-16052 is capable of SPP, EPP, and ECP modes. Use SW2, switches 1 (MODE-1) and
2 (MODE-2) to set the parallel port transfer mode.
[The ECP mode requires setting jumpers JP5 or JP6; refer to the next section, DREQ and DACK Lines (ECP
Mode Only), for these configurations.]
Parallel Port
Transfer Mode
SPP (Default)
ECP
EPP
Disable
* 0 = up; 1 = down
MODE-1
1
0
1*
0
MODE-2
0
0
1
1
5
A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA A AAAA
A
A
IDE-16052 Installation Guide
AA
AA
A
A
A
Part Number: 510999-00, Rev. B
A
A
Print Spec Number: 494453-00
A
A
A
Current Date: 4/29/96
A
ECN Date: 5/7/96
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A
DREQ and DACK Lines (ECP Mode Only)
Use JP5 and JP6 to set the DMA request (DREQ) and
DMA acknowledge (DACK) lines for DMA channels 1 or 3. Use the ECP/EPP setting if ECP is enabled, otherwise; use the SPP default setting.
Note:
DREQ and DACK channel numbers (1/3) must be paired.
DREQ/DACK JP5 JP6 Setting
SPP (Default)
1
DREQ/DACK 1
ECP/EPP with DMA 1
DREQ/DACK 3
1
1
1
Pins 1, 2, and 3 off
Pin 1 off; pins 2 and 3 on
ECP/EPP with DMA 3
Pins 1 and 2 on; pin 3 off
1 1
Enable/Disable Parallel Port
Set SW2, switch 3 (LPT1/2) down to enable LPT 1; set SW2, switch 3 up to enable LPT 2.
Parallel Port Interrupts
Use JP2 to set the interrupts for the parallel ports.
Use the LPT 1/2 setting that matches the one you made in the previous section, Enable/Disable Parallel
Port.
Parallel Port, IRQ JP2 Setting
LPT 1, IRQ 7 Pin 1 off; pins 2 and 3 on
1
LPT 2, IRQ 5 Pins 1 and 2 on; pin 3 off
1
6
A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA A AAAA
A
A
IDE-16052 Installation Guide
AA
AA
A
A
A
Part Number: 510999-00, Rev. B
A
A
Print Spec Number: 494453-00
A
A
A
Current Date: 4/29/96
A
ECN Date: 5/7/96
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A
Serial Port
The IDE-16052 has two high-speed serial ports, which can be configured as COM 1/3 and/or
COM 2/4.
Serial Port 1
Use SW2, switch 6 (COM1/3) to select COM 1 or
COM 3. Use SW2, switch 7 (ENABLE) to enable or disable serial port 1.
COM 1 or COM 3 COM1/3
COM 1*
COM 3
Disable
1
0 x
* Default setting; 0 = up; 1 = down; x = up or down
ENABLE
1
1
0
Use JP1 to set the interrupts for serial port 1.
COM Port, IRQ JP1 Setting
COM 1, IRQ 4 Pin 1 off; pins 2 and 3 on
1
COM 3, IRQ 9 Pins 1 and 2 on; pin 3 off
1
COM 3, IRQ 4* Pin 1 off; pins 2 and 3 on
1
* These settings apply when SW2, switch 6 is set up and switch 7 is set down.
Serial Port 2
Use SW2, switch 4 (COM2/4) to select COM 2 or
COM 4. Use SW2, switch 5 (ENABLE) to enable or disable serial port 2.
COM 2 or COM 4 COM2/4
COM 2*
COM 4
Disable
1
0 x
* Default setting; 0 = up; 1 = down; x = up or down
ENABLE
1
1
0
7
A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA A AAAA
A
A
IDE-16052 Installation Guide
AA
AA
A
A
A
Part Number: 510999-00, Rev. B
A
A
Print Spec Number: 494453-00
A
A
A
Current Date: 4/29/96
A
ECN Date: 5/7/96
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A
Use JP2 to set the interrupts for serial port 2.
COM Port, IRQ JP2 Setting
COM 2, IRQ 3 Pin 1 off; pins 2 and 3 on
1
COM 4, IRQ 5 Pins 1 and 2 on; pin 3 off
1
COM 4, IRQ 3* Pin 1 off; pins 2 and 3 on
1
* These settings apply when SW2, switch 4 is set up and switch 5 is set down.
Installation
1
Turn
OFF
the power to your computer and any attached devices, and disconnect the power cord.
WARNING:
To avoid possible exposure to electric shock, be sure the power to your system is turned
OFF
.
2
Remove the cover from the computer case.
3
Touch an unpainted metal part of the computer to discharge any static electricity from your clothes and body. (Use a wrist grounding strap if you have one.)
4
Carefully remove the IDE-16052 from its antistatic packaging.
5
Configure the host adapter’s jumpers and switches according to the settings in Configura-
tion, which begins on page 1.
6
Replace the expansion slot cover of an empty slot with the HCA-138 serial bracket provided with the host adapter, and attach the serial bracket’s cable to connector J6.
8
A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA A AAAA
A
A
IDE-16052 Installation Guide
AA
AA
A
A
A
Part Number: 510999-00, Rev. B
A
A
Print Spec Number: 494453-00
A
A
A
Current Date: 4/29/96
A
ECN Date: 5/7/96
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A
7
Attach internal cables and devices to the following connectors, as needed:
Connector
J2
J3, J4
Device
Floppy drives
IDE or EIDE devices
8
Choose an empty 16-bit ISA-bus expansion slot, and remove its slot cover. (Be sure to save the screw.)
9
Holding the IDE-16052 host adapter with both hands, align it with the slot and insert the host adapter firmly into the socket.
10
Attach the host adapter bracket to the computer chassis with the screw from the expansion slot cover you removed in step 8.
11
Attach external devices to the following connectors, as needed:
Connector
J9
J10
J7
Device
Serial device
Parallel device
Serial device
12
Replace the cover on the computer case.
13
Reconnect the power cords to all external devices and the computer.
14
Turn
ON
the power to the external devices, and then turn
ON
the power to the computer.
15
Make sure all hard disk drives connected to the
IDE-16052 are set to Not Installed in system
CMOS Setup. Refer to your computer documentation for more information.
16
Make sure all IDE devices are recognized by the
IDE-16052 BIOS scan (SW1, switch 8 must be set down) and displayed on the monitor during bootup.
9
A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA A AAAA
A
A
IDE-16052 Installation Guide
AA
AA
A
A
A
Part Number: 510999-00, Rev. B
A
A
Print Spec Number: 494453-00
A
A
A
Current Date: 4/29/96
A
ECN Date: 5/7/96
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A
Specifications
Host bus
Peripheral bus
Command set
ISA; one 16-bit slot
IDE (ATA-2); dual channel
ATA-2, SFF-8020, ATAPI CD-ROM,
QIC-157 tape standards
Transfer method
PIO mode 0, double-word (32-bit)
IDE interrupts
IRQ 14; IRQ 15; IRQ 10; IRQ 11
IDE I/O ports
Floppy
Serial
1F0h; 170h; 160h/168h; 1E8h
Up to two; 360KBytes, 720KBytes,
1.2MBytes, 1.44MBytes, 2.88MBytes capacity
Transfer speed: Up to 115.2Kbits/sec
Parallel
Serial ports: two; 03F8h (COM 1*);
02F8h (COM 2*); 03E8h (COM 3);
02E8h (COM 4)
Interrupts: IRQ 3*; IRQ 4*; IRQ 5;
IRQ 9
Mode support:
Standard parallel port (SPP)*
Enhanced parallel port (EPP)
Enhanced capabilities port (ECP)
Transfer speed: Up to 2MBytes/sec
(ECP)
Parallel ports: one; 0378h (LPT 1*);
0278h (LPT 2)
Interrupts: IRQ 5; IRQ 7*
* Default settings
10
A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA A AAAA
A
A
IDE-16052 Installation Guide
AA
AA
A
A
A
Part Number: 510999-00, Rev. B
A
A
Print Spec Number: 494453-00
A
A
A
Current Date: 4/29/96
A
ECN Date: 5/7/96
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A
Troubleshooting
The IDE-16052 has been configured to work with either single or dual IDE channel motherboards. The host adapter will display the following BIOS messages during the power-on self-test (POST):
Scanning for IDE controllers and devices…
Controller 0 at IO port XXXh, IRQ YY…
Device 0 - ZZZ
Device 1 - ZZZ
Controller 1 at IO port XXXh, IRQ YY…
Device 0 - ZZZ.
Device 1 - ZZZ
Where:
XXX
YY
ZZZ
F/W Rev.
F/W Rev.
F/W Rev.
F/W Rev.
= the I/O port location of the IDE channels
= the IRQ selection of the IDE channels
= the name of the IDE or EIDE devices
If you do not see the BIOS message or if you are having problems installing your EIDE host adapter, try the following:
1
Make sure the IDE-16052 BIOS is enabled, i.e.,
SW1, switch 8 is set down.
2
Change the memory address of the BIOS (refer to
BIOS Memory Address on page 3). It might be conflicting with a video controller or other controller using a ROM BIOS.
Note:
Make sure the EIDE adapter is not conflicting with another add-in host adapter or IDE channel on the motherboard.
If there is another EIDE host adapter or IDE connector on the motherboard, check the number of
IDE connectors. If there is only one connector, then the primary IDE channel (I/O port 1F0h,
IRQ 14) is in use. If there are two connectors, the primary and secondary IDE channels (I/O port
170h, IRQ 15) are in use.
To avoid conflicts, use an alternate IDE channel.
Refer to IDE Channels on page 4 for instructions.
3
Make sure the EIDE device is correctly configured either as device 0 (master) or device 1 (slave). Refer to the device documentation for more information.
11
A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA A AAAA
A
A
IDE-16052 Installation Guide
AA
AA
A
A
A
Part Number: 510999-00, Rev. B
A
A
Print Spec Number: 494453-00
A
A
A
Current Date: 4/29/96
A
ECN Date: 5/7/96
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A
4
The IDE channel (1E8h/IRQ 11) might conflict with the COM 3 alternate status register (3EEh) when using certain types of communication software. Attach your serial device to a different
COM port, or use a different I/O port for the IDE device.
5
Certain PCI video controllers use I/O ports
2ECh–2EEh. These ports conflict with the COM 4
I/O port range of 2E8h–2EEh. Change the COM port setting, or try a different video card.
Adaptec Technical Support and Services
If you have questions about installing or using the host adapter, check this installation guide first—you will find answers to most of your questions here. If you need further assistance, please contact us. We offer the following support and information services:
Electronic Support
Technical information, including product literature, answers to commonly asked questions, information on software upgrades and other topics, is available electronically through the following:
■
■
■
■
■
Adaptec World Wide Web (WWW) site at http://www.adaptec.com.
File Transfer Protocol (FTP) server at ftp.adaptec.com
.
CompuServe Adaptec Forum at GO ADAPTEC.
Adaptec USA Bulletin Board Service (BBS) at 408-945-7727; supports up to 28,800 bps (bits per second), 8 data bits, 1 stop bit, no parity. No product literature is available on the Adaptec BBS.
Interactive Fax System at 408-957-7150; available 23 hours a day, 7 days a week. The fax system is out of service 1 hour each day.
Technical and Product Support
■
■
■
For technical support and information about Adaptec’s electronic support services, call 800-959-SCSI (7274) or 408-945-2550, 24 hours a day,
7 days a week.
To use the Adaptec Interactive Support System, call
800-959 SCSI (7274) or 408-945-2550, 24 hours a day, 7 days a week The system prompts you with questions regarding your problem and then provides step-by-step troubleshooting instructions.
To speak with a product support representative, call
408-934-SCSI (7274), M–F, 6:00
A
.
M
. to 5:00
P
.
M
., Pacific Time.
After hours, on weekends, and on holidays, product support is also available for a fee at 800-416-8066.
Sales and Ordering Information
■
■
■
For sales information, call 800-959-SCSI (7274) or 408-945-2550, M–F,
6:00
A
.
M
. to 5:00
P
.
M
., Pacific Time.
To order Adaptec software and SCSI cables, call 800-442-SCSI (7274) or
408-957-SCSI (7274), M–F, 6:00
A
.
M
. to 5:00
P
.
M
., Pacific Time.
To request additional documentation for Adaptec products, call
800-934-2766 or 510-732-3829, M–F, 6:00
A
.
M
. to 5:00
P
.
M
., Pacific Time.
12
A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA A AAAA
A
A
IDE-16052 Installation Guide
AA
AA
A
A
A
Part Number: 510999-00, Rev. B
A
A
Print Spec Number: 494453-00
A
A
A
Current Date: 4/29/96
A
ECN Date: 5/7/96
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause interference to radio or television equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
■
■
■
■
Reorient or relocate the receiving antenna
Move the equipment away from the receiver
Plug the equipment into an outlet on a circuit different from that to which the receiver is powered
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions
CAUTION: Only equipment certified to comply with Class B (computer input/output devices, terminals, printers, etc.) should be attached to this equipment, and must have shielded interface cables.
Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the user ’s authority to operate such equipment.
Each host adapter is equipped with an FCC compliance label that shows only the FCC identification number. The full text of the associated label follows:
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
Canadian Compliance Statement
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matérial brouilleur du Canada.
R
Adaptec, Inc.
691 South Milpitas Blvd.
Milpitas, CA 95035
Copyright © 1996, Adaptec, Inc. All rights reserved. Adaptec and the
Adaptec logo are trademarks of Adaptec, Inc., which may be registered in some jurisdictions. Future Domain and the Future Domain logo are trademarks of Future Domain Corporation, which may be registered in some jurisdictions. All other trademarks are owned by their respective owners.
Printed in Singapore
Stock No.: 510999-00, Rev. B CW 4/96
Information subject to change without notice.
13
A AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA
AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AA AA A AAAA
A
A
IDE-16052 Installation Guide
AA
AA
A
A
A
Part Number: 510999-00, Rev. B
A
A
Print Spec Number: 494453-00
A
A
A
Current Date: 4/29/96
A
ECN Date: 5/7/96
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A
