advertisement
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Xtreme/SBC PCIe/104 Single Board Computer
& PCIe/104 Qseven Carrier Board
Connect Tech Inc.
Tel:
519-836-1291
42 Arrow Road
Guelph, Ontario
Toll:
800-426-8979 (North America only)
Fax:
519-836-4878
N1K 1S6
Email:
[email protected]
www.connecttech.com
Revision: 0.06
Page 1 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
CTIM-00058 Revision 0.06 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Table of Contents
Document: CTIM-00058
Revision: 0.06
Page 2 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Document: CTIM-00058
Revision: 0.06
Page 3 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Customer Support Overview
If you experience difficulties after reading the manual and/or using the product, contact the
Connect Tech reseller from which you purchased the product. In most cases the reseller can help you with product installation and difficulties.
In the event that the reseller is unable to resolve your problem, our highly qualified support staff can assist you. Our support section is available 24 hours a day, 7 days a week on our website at: www.connecttech.com/sub/support/support.asp.
See the contact information section below for more information on how to contact us directly. Our technical support is always free.
Contact Information
We offer three ways for you to contact us:
Mail/Courier
You may contact us by letter at:
Connect Tech Inc.
Technical Support
42 Arrow Road
Guelph, Ontario
Canada N1K 1S6
Email/Internet
You may contact us through the Internet. Our email and URL addresses on the Internet are: [email protected] [email protected] www.connecttech.com
Note:
Please go to the Download Zone or the
Knowledge Database
in the
Support Center
on the Connect
Tech website for product manuals, installation guides, device driver software and technical tips.
Submit your technical support questions to our customer support engineers via the
Support Center
on the Connect Tech website.
Telephone/Facsimile
Technical Support representatives are ready to answer your call Monday through Friday, from
8:30 a.m. to 5:00 p.m. Eastern Standard Time. Our numbers for calls are:
Toll Free: 800-426-8979 (North America only)
Telephone: 519-836-1291 (Live assistance available 8:30 a.m. to 5:00 p.m. EST,
Monday to Friday)
Facsimile: 519-836-4878 (on-line 24 hours)
Document: CTIM-00058
Revision: 0.06
Page 4 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Limited Product Warranty
Connect Tech Inc. provides a two-year Warranty for the Xtreme/SBC PCIe/104 Single Board
Computer and PCIe/104 Qseven Carrier Board. Should this product, in Connect Tech Inc.'s opinion, fail to be in good working order during the warranty period, Connect Tech Inc. will, at its option, repair or replace this product at no charge, provided that the product has not been subjected to abuse, misuse, accident, disaster or non-Connect Tech Inc. authorized modification or repair.
You may obtain warranty service by delivering this product to an authorized Connect Tech Inc. business partner or to Connect Tech Inc. along with proof of purchase. Product returned to
Connect Tech Inc. must be pre-authorized by Connect Tech Inc. with an RMA (Return Material
Authorization) number marked on the outside of the package and sent prepaid, insured and packaged for safe shipment. Connect Tech Inc. will return this product by prepaid ground shipment service.
The Connect Tech Inc. Limited Warranty is only valid over the serviceable life of the product.
This is defined as the period during which all components are available. Should the product prove to be irreparable, Connect Tech Inc. reserves the right to substitute an equivalent product if available or to retract the Warranty if no replacement is available.
The above warranty is the only warranty authorized by Connect Tech Inc. Under no circumstances will Connect Tech Inc. be liable in any way for any damages, including any lost profits, lost savings or other incidental or consequential damages arising out of the use of, or inability to use, such product.
Copyright Notice
The information contained in this document is subject to change without notice. Connect Tech
Inc. shall not be liable for errors contained herein or for incidental consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Connect Tech, Inc.
Copyright  1997 - 2017 by Connect Tech, Inc.
Trademark Acknowledgment
Connect Tech, Inc. acknowledges all trademarks, registered trademarks and/or copyrights referred to in this document as the property of their respective owners.
Not listing all possible trademarks or copyright acknowledgments does not constitute a lack of acknowledgment to the rightful owners of the trademarks and copyrights mentioned in this document.
Document: CTIM-00058
Revision: 0.06
Page 5 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Revision History
Revision 0.00 – May 28, 2010
Revision 0.01 – August 18, 2010
Revision 0.02 – March 8, 2011
Revision 0.03 – June 1, 2012
Revision 0.04 – June 7, 2016
Revision 0.05 – February 13, 2017
Revision 0.06 – August 9, 2017: Added cable drawing links, Updated format
Introduction
Connect Tech’s Xtreme/SBC is a small embedded carrier board that utilizes the PCI/104-Express form factor, which has the standard PC/104 dimensions with 4 x1 PCIe lanes. This carrier board includes the required connectors and cables for easy connection to 2x SATA, 2x RS-232, 2x RS-
422/485, 4x USB 2.0, 1x Gigabit Ethernet, LVDS and VGA Video.
The PCIe/104 Single Board Computer allows complete integration with any industry standard
Qseven module, transforming it into a robust Single Board Computer (SBC) in the PC/104 form factor. Xtreme/SBC is ideal for a broad range of embedded applications. The Qseven standard allows upgrading to the latest processor and memory technology with ease, while maintaining the
I/O interfaces.
Features
ï‚· Qseven module carrier
ï‚· PCIe-104 form factor
ï‚· Four x1 PCIe Lanes
ï‚· Dual display, VGA (via SDVO) and 1x24 LVDS
ï‚· 2x SATA
ï‚· 2x RS232
ï‚· 2x RS485
ï‚· 1x 10/100/1000 Ethernet
ï‚· ATX power input or +5V/+12V only operation
What is Qseven?
Qseven is a standard that enables integration of Computer-on-Modules with mobile and embedded applications. To learn more about Connect Tech’s PCIe/104 Single Board Computer, visit http://connecttech.com/product-category/technology/sbc/.
Document: CTIM-00058
Revision: 0.06
Page 6 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
System Block Diagram
The Qseven module implements the core processing features including: processor, memory, and system physical interfaces via the southbridge.
Many of the Qseven modules are based on the mobile Intel Atom architecture (Z series processor + Poulsbo
/ SCH US15W chipset); shown in the block diagram below.
This document will generally refer to the features of the US15W.
Document: CTIM-00058
Revision: 0.06
Page 7 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Hardware Description
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Connector Locations
PCI/104-Express Single Board Computer – Top
PCI/104-Express Single Board Computer – Bottom
Document: CTIM-00058
Revision: 0.06
Location
P1
P2
P3A, P3B
P4
P5
P6
P7
P8
P9
P10A, P10B
P11
P12
P13
P14
P16
Connector Summary
Connection
Q7
PCIe-104
USB
GBE
VGA
ATX Power
LVDS Video
LVDS Backlight
RS232 serial
SATA
RS485 serial
PCI-104
PS/2 Keyboard &
Mouse
Fan Power
Battery holder
Page 8 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Jumper Summary
Jumper
J1
J2
J3
J4
J5
J6
J7
J8
J9
Function
PS/2 power
Fan Power
Fan PWM polarity
LVDS panel power
LVDS backlight enable polarity
LVDS Backlight
Power
Suspend Selection
Power Supply On
Power Button
Date: 2017-08-09
Qseven Module Interface
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Description
The processor and Chipset are implemented on the Qseven CPU module, which connects to the
Xtreme/SBC via a MXM connector. As previously mentioned, many of the existing Qseven Modules use the Intel Atom mobile architecture, Z series processor + Poulsbo / SCH US15W chipset. The Xtreme/SBC implements a subset of the Qseven features, as describe in the introduction.
For a list of Qseven module vendors, visit http://www.qseven-standard.org/
Connector
Function Qseven interface
Location
P1
Type
MXM
Foxconn AS0B326-S78N-7F (or equivalent)
Pinout
Refer to Qseven specification
Graphics
The availability of the graphics interfaces depends on the Qseven module selected.
US15W: The US15W chipset provides GMA 500 graphics sub-system and provides two display interfaces:
SDVO (serial digital video output) and LVDS (low voltage differential signalling). The resolution is generated by the by GMA 500 is limited 1280x1024.
The configuration of either interface as the primary or secondary display depends on the Qseven module’s
BIOS capabilities and settings. Refer to the Qseven module’s documentation for more details.
VGA
Description
The VGA interface is implemented using the Qseven SDVO interface, with a SDVO to VGA converter
(Chrontel CH7317B) which supports resolutions up to 1920x1200; however actually resolutions depend on the Qseven module.
Connector
Function VGA graphics
Location
P5
Type
2x5 2mm header
MLE TSHSM-205-D-06-G-V-L (or equivalent)
Pinout
Pin
1
3
5
7
9
Signal
DAC_RED
DAC_GREEN
DAC_BLUE
HSYNC
VSYNC
Pin
2
4
6
8
10
Signal
GND
N/C
SC_DDC
SD_DDC
GND
Document: CTIM-00058
Revision: 0.06
Page 9 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
LVDS
Description
The
Xtreme/SBC
provides dual 18 or 24 bit LVDS display channels via P7, which are connected directly from the Qseven module . LVDS panel supply power is selected with jumper J4 and backlight power is selected with jumper J6. Both are current limited to 500 mA.
US15W: The US15W provides only a single 18 or 24 bit display channel. Each LVDS data pair carries two bits, each channel has four data pairs.
Connectors & Jumpers
Function LVDS Graphics
Location
P7
Type
Hirose DF14-30P-1.25H connector
Pinout
11
12
13
14
7
8
9
10
Pin
1
2
3
4
5
6
Signal
VCC_PNL
VCC_PNL
GND
GND
LVDS_A3_N
LVDS_A3_P
LVDS_CLK_N
LVDS_ACLK_P
GND
LVDS_A2_N
LVDS_A2_P
LVDS_A1_N
LVDS_A1_P
LVDS_A0_N
Description
Panel Power
Panel Power
Digital ground
Digital ground
Channel A Data
Channel A Data
Channel A Clock
Channel A Clock
Digital ground
Channel A Data
Channel A Data
Channel A Data
Channel A Data
Channel A Data
15
16
17
LVDS_A0_P
GND
LVDS_B3_N
18 LVDS_B3_P
19 LVDS_BCLK_N
20 LVDS_BCLK_P
21 GND
Channel A Data
Digital ground
Channel B Data
Channel B Data
Channel B Clock
Channel B Clock
Digital ground
22
23
24
25
26
LVDS_B2_N
LVDS_B2_P
LVDS_B1_N
LVDS_B1_P
LVDS_B0_N
Channel B Data
Channel B Data
Channel B Data
Channel B Data
Channel B Data
27
28
LVDS_B0_P
GND
Channel B Data
Digital ground
29 LVDS_DID_CLK Display ID Clock
(3.3V)
30 LVDS_DID_DATA Display ID Data (3.3V)
Document: CTIM-00058
Revision: 0.06
Page 10 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Function LVDS backlight power
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Location
P8
Type
Hirose DF13-8P-1.25H connector
Pinout
Pin
1
2
3
4
5
6
7
8
Signal
+12V
+12V
+5V
+5V
LVDS_BLEN
VCC_BKL
GND
GND
Description
+12 V DC, max. 1A
+12 V DC, max. 1A
+5 V DC, max. 1A
+5 V DC, max. 1A
Backlight enable, level selected with J4
Back light power, selected with J6
Digital ground
Digital ground
Function LVDS backlight power select
Selects either +12V or +5V. Refer to the display panel’s documentation for proper configuration.
Location
J6
Type
1x3 0.100” jumper block
Pinout
Position
1-2
2-3 off
Description
+12V
+5V floating
Default
+12V
Function LVDS panel power select
Selects either +3.3V or +5V. Refer to the display documentation for proper configuration.
Location
J4
Type
1x3 0.100” jumper block
Pinout
Position
1-2
2-3 off
Description
+5V
+3.3V floating
Default
+3.3V
* Note the silk screen labels +5V and +3.3V are reversed on Revision A.
Document: CTIM-00058
Revision: 0.06
Page 11 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Function LVDS backlight enable polarity
Selects either positive or negative. Refer to the inverter power supply documentation for proper configuration.
Location
J5
Type
1x2 2mm jumper block
Pinout
Position
off on
Description
Positive polarity
Negative polarity
Default
Positive polarity
Gigabit Ethernet
Description
The gigabit Ethernet interface’s controller (MAC + PHY) is implemented on the Qseven module, while the
Xtreme/SBC provides the necessary magnetics and termination.
Most Qseven modules support 1000BASE-T, 100BASE-TX, and 10BASE-T standards with either a
Realtek 8111 or Intel 82574 PCIe Ethernet controller.
Connector & LEDs
Function Gigabit Ethernet
Location P8
Type
2x5 2mm header
MLE TSHSM-205-D-06-G-V-L (or equivalent)
Pinout
Pin Signal Description Pin Signal Description
1
3
MX1-
MX2-
5 FGND
7
9
MX3-
MX4-
Data
Data
Frame
Ground
Data
Data
2
4
6
8
10
MX1+
MX2+
FGND
MX3+
MX4+
Data
Data
Frame
Ground
Data
Data
Function Ethernet Status LEDs
Locations
Pin Signal
D9 Activity
D10 1000BASE-T Link
D11 100BASE-TX Link
D12 10BASE-T Link
Document: CTIM-00058
Revision: 0.06
Page 12 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
USB 2.0
Description
The Xtreme/SBC implements 4 of the 8 available USB 2.0 connections via two connectors. Over current protection and power supply filtering is provided.
Only the USB host features of the Qseven specification have been implemented, USB client features are not supported.
Connector
Function USB 2.0 x2
Locations P3A, P3B
Type
Hirose DF13-8P
Pinout
Pin
4
5
6
7
8
1
2
3
Signal
VCC_USB_0
USB_0_N
USB_0_P
USB_GND_0
USB_GND_1
USB_1_N
USB_1_N
VCC_USB_1
Description
Port 0 Filtered +5V
Port 0 Data
Port 0 Data
Port 0 Filtered Digital Ground
Port 1 Filtered Digital Ground
Port 1 Data
Port 1 Data
Port 1 Filtered +5V
SATA
Description
The Xtreme/SBC provides 2 SATA host connections.
US15W: Most Qseven modules based on the US15W, convert the US15W’s IDE interface to one SATA connection (as IDE master) and one built-in NAND based flash drive (as IDE slave). Consult the Qseven module’s documentation for more information.
In this case only P10A connector is active
Document: CTIM-00058
Revision: 0.06
Page 13 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Connector & LEDs
Function SATA host
Locations P10A, P10B
Type
Industry standard right angle sata host connector
Molex 0470804005 (or equivalent)
P10A
Pinout
Pin
5
6
7
1
2
3
4
Signal
GND
SATA_TX_P
SATA_TX_N
GND
SATA_RX_N
SATA_RX_P
GND
P10B
Function SATA Status LEDs
Locations
Pin
D13
Signal
Activity
PCI/104-Express
Description
The Xtreme/SBC provides 4 x1 PCIe lanes to the PCI/104-Express connector; allowing four PCIe-104 boards to be stacked on top. The 4 x1 PCIe lanes are implemented via an IDT 1-4 PCIe switch, consuming only one of the available PCIe lanes from the Qseven modules. Most US15W Qseven modules expose only one PCIe lane.
Note: The Xtreme/SBC provides 3.3V generated from the ATX +5V input power. It is limited to 3.5A.
Connectors
Function PCIe-104 top mount
Locations P2
Type
Industry standard
Samtec ASP-129637-03
Pinout
The following table indicates which of the PCIe-104 signals are connected
Document: CTIM-00058
Revision: 0.06
Page 14 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
5
6
7
8
9
10
Pin Description Pin Description Pin Description
1 N/C 53 WAKE# 105 N/C
2 PE_RST# 54 PEG_ENA# 106
3 +3.3V 55 GND 107
4 +3.3V 56 GND 108
N/C
GND
GND
N/C
N/C
N/C
N/C
GND
GND
57
58
59
60
61
62
N/C
N/C
N/C
N/C
GND
GND
109
110
111
112
113
114
N/C
N/C
N/C
N/C
GND
GND
11 PEx1_1Tp 63
12 PEx1_0Tp 64
13 PEx1_1Tn 65
14 PEx1_0Tn 66
15 GND 67
16 GND 68
17 PEx1_2Tp 69
18 PEx1_3Tp 70
19 PEx1_2Tn 71
20 PEx1_3Tn 72
21 GND 73
22 GND 74
23 PEx1_1Rp 75
24 PEx1_0Rp 76
N/C
N/C
N/C
N/C
GND
GND
N/C
N/C
N/C
N/C
GND
GND
N/C
N/C
115
116
117
118
119
120
121
122
123
124
125
126
127
128
N/C
N/C
N/C
N/C
GND
GND
N/C
N/C
N/C
N/C
GND
GND
N/C
N/C
25 PEx1_1Rn 77
26 PEx1_0Rn 78
27 GND 79
28 GND 80
29 PEx1_2Rp 81
30 PEx1_3Rp 82
31 PEx1_2Rn 83
32 PEx1_3Rn 84
33
34
GND
GND
85
86
35 PEx1_1Clkp 87
36 PEx1_0Clkp 88
37 PEx1_1Clkn 89
38 PEx1_0Clkn 90
39
40
+5V_SB
+5V_SB
91
92
41 PEx1_2Clkp 93
42 PEx1_3Clkp 94
43 PEx1_2Clkn 95
44 PEx1_3Clkn 96
45 CPU_DIR 97
46 PWRGOOD 98
47 SMB_DAT 99
48 N/C 100
49 SMB_CLK 101
50 N/C 102
51 SMB_ALERT 103
52 PSON# 104
N/C
N/C
GND
GND
N/C
N/C
N/C
N/C
GND
GND
N/C
N/C
N/C
N/C
GND
GND
N/C
N/C
N/C
N/C
GND
GND
N/C
N/C
N/C
N/C
GND
GND
149
150
151
152
153
154
155
156
143
144
145
146
147
148
135
136
137
138
139
140
141
142
129
130
131
132
133
134
GND
GND
N/C
N/C
N/C
N/C
GND
GND
N/C
N/C
N/C
N/C
GND
GND
N/C
N/C
GND
GND
N/C
N/C
N/C
N/C
GND
GND
N/C
N/C
N/C
N/C
Document: CTIM-00058
Revision: 0.06
Page 15 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Function
PCI-104 top mount – mechanical only, does not carry signals
Locations P12
Type
Industry standard
EPT 264-60303-02
Note
Connector is not populated by default.
Can be installed on request.
LPC Super I/O
The Xtreme/SBC implements many low speed legacy I/O features with the SMSC SCH3114 Super I/O, which is connected to the Qseven module via the LPC (Low Pin Count) bus. This Super I/O device provides 4 serial ports, 2 PS/2, and many other status / control features.
Note: the Qseven specification states that all Qseven modules BIOS implementations must support either the Winbond W83627 or SMSC SCH3114.
Document: CTIM-00058
Revision: 0.06
Page 16 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Serial
Description
Two RS232 serial ports are provided on P9 and two RS485 serial ports are provided on P11.
For the RS485 ports, the default configuration is full duplex without any bias or termination. Various resistors configurations can be populated to enabled TX and RX termination as well as RTS control. The following diagram shows the available configuration options. Contact Connect Tech’s support department for further information.
Resistor
R99
R101
R156
R160
R98
R102
R100
R97
Function
Always enable driver
Always enable receiver
RTS controlled receiver
RTS controlled driver
Receiver termination
Driver termination
Receiver bias
Receiver bias
Default
Populated
Populated
Document: CTIM-00058
Revision: 0.06
Page 17 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Connectors
Function RS232 x2
Locations P9
Type
2x10 2mm header
Pinout
Pin
9
11
13
15
1
3
5
7
17
19
Signal
DCD1
RXD1
TXD1
DTR1
GND
DCD2
RXD2
TXD2
DTR2
GND
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Pin
10
12
14
16
2
4
6
8
18
20
Signal
DSR1
RTS1
CTS1
RI1
N/C
DSR2
RTS2
CTS2
RI2
N/C
Function RS485 x2
Locations P11
Type
2x10 2mm header
Pinout
Pin
11
13
15
17
19
1
3
5
7
9
Signal
RXD0+
TXD0+
TXD0-
RXD0-
GND
RXD1+
TXD1+
TXD1-
TXD1-
GND
Pin
12
14
16
18
20
2
4
6
8
10
Signal
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
Document: CTIM-00058
Revision: 0.06
Page 18 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
PS/2 Keyboard and Mouse
Description
A PS/2 keyboard and PS/2 mouse interface are provided via P13; where the PS/2 voltage is selectable with
J1. Refer to the specification printed on the bottom of the keyboard and mouse to determine which voltage to select; in most cases this is 5V.
Connectors & Jumpers
Function PS/2 Keyboard and Mouse
Locations P13
Type
Molex 0532610671 connector
Pinout
Pin
1
2
3
4
5
6
Signal
KDAT
KCLK
PS2_GND
PS2_VCC
MDAT
MCLK
Description
Keyboard Data
Keyboard Clock
Filtered digital ground
Filtered PS/2 supply voltage, via
J1
Mouse Data
Mouse Clock
Function PS/2 voltage select
Selects either +3.3Vauxiliary or +5V auxiliary.
Location
J1
Type
1x3 0.1” jumper
Pinout
Position
1-2
2-3 off
Description
+3.3V_A
+5V_A floating
Default
+3.3V
Document: CTIM-00058
Revision: 0.06
Page 19 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Power
Description
The Xtreme/SBC is designed to be powered from an ATX type power supply, and support many of the
ACPI features like suspend to RAM. A CR1225 battery holder (P16) provides the VBAT for the Qseven module.
The Xtreme/SBC generates 3.3V on board, to facilitate alternate powering options.
WARNING: Do not attach a PCIe-104 power supply to P2 (the PCIe104 connector). These power supplies typically generate 3.3V, which would conflict with the onboard 3.3V.
Other powering options include
A) +5V & +12V only: The ATX features can be bypassed by powering +5V_SB with same 5 volt supply as the +5V input pins.
B) +5V only: similar to the above cause, but excluding the +12V which is used only by the backlight and
PCIe-104 connector. Before attempting this, verify that this configuration is appropriate for the target installation.
Connectors & Jumpers
Function ATX input power
Location P6
Type
JST B15B-EH-A
Pinout
Pin
1
Signal
+5V
2
3
4
5
6
7
8
9
10
11
12
13
14
15
GND
+5V
GND
+5V
+5V_SB
GND
PSON#
PWROK
+3.3V
GND
+12V
+12V
GND
-12V
Description
+5V input, powers onboard power regulators & Qseven module
Digital Ground
+5V input, powers onboard power regulators & Qseven module
Digital Ground
+5V input, powers onboard power regulators & Qseven module
+5V standby input, powers +3.3V auxiliary power
Digital Ground
Power Supply On
Power OK
+3.3V input, not used by
Xtreme/SBC. +3.3V is derived on internally
Digital Ground
+12V input, used by PCIe104 and backlight
+12V input, used by PCIe104 and backlight
Digital Ground
-12V input, not used
Document: CTIM-00058
Revision: 0.06
Page 20 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Function Suspend Selection
Selects either S3 or S5.
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Location
J7
Type
1x3 2 mm
Pinout
Position
1-2
2-3 off
Description
Suspend S3
Suspend S5
Floating
Default
S3
Function Power Supply on
Selects either PS_ON# signal from Qseven module or always on
Location
J8
Type
1x3 2mm
Pinout
Position
1-2
2-3 off
Description
Always on
Qseven PS_ON# floating
Default
Qseven PS_ON#
Function Power Button
Use to connect a momentary push button to the Qseven
PWR_BTN# signal
Location
J9
Type
1x2 2mm header
Pinout
Position
1
2
Description
PWR_BTN#
Ground
Document: CTIM-00058
Revision: 0.06
Page 21 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Fan Control
Description
If actively cooling is required; P14 can be used to power and control a fan with J2 selecting the fan voltage.
Connectors & Jumpers
Function Fan power/control
Location
P14
Type
JST B15B-EH-A connector
Pinout
Pin
1
2
3
Signal
FAN_SPEED
FAN_PWR
FAN_GND
Description
Speed signal
Fan power selected by J2
Filtered digital ground
Function Fan power Selection
Selects either +5V or +12V.
Location
J2
Type
1x3 0.100” jumper
Pinout
Position
1-2
2-3 off
Description
+12V
+5V
Floating
Default
floating
Function Fan PWM polarity
Selects either positive or negative
Location
J3
Type
1x2 2mm jumper
Pinout
Position
off on
Description
Positive
Negative
Default
floating
Document: CTIM-00058
Revision: 0.06
Page 22 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Battery
Description
A CR1225 battery holder is provided at P16. This is a standard 3V battery, which powers the RTC (real time clock) on the CPU module. In most cases, it is not required to preserve critical BIOS settings as most
Qseven modules have a flash based BIOS.
Connector & LEDs
Function Battery
Location
P16
Type
CR1225 battery holder
Hardware Installation
1. Ensure all external system power supplies are off.
2. Install the Qseven module into P1. Be sure to follow the manufacturer’s direction for proper heatsink/heatspreader installation.
3. Verify all jumper settings from the relevant sections, paying special attention the power selection jumpers
Jumper Function
Selection Position
J1
J2
J3
J4
J5
J6
J7
J8
PS/2 power
Fan Power
Fan PWM polarity
LVDS panel power
+5V
+12V
Positive
+3.3V positive LVDS backlight enable polarity
LVDS Backlight
Power
+12V
Suspend Selection S3
Power Supply On From Qseven module
2-3
1-2
Off
2-3
Off
1-2
1-2
2-3
4. Install the necessary cables for the application. At a minimum, this would include: a) Power cable, either ATX or +5V/+12V only b) Display cable, either VGA or LVDS c) Keyboard, either PS/2 or USB d) Power button, if applicable
For the relevant cables, see the Cables & Interconnect section of this manual
5. Stack any necessary PCIe-104 modules on top of the Xtreme/SBC via P2, with the appropriate mounting hardware
Document: CTIM-00058
Revision: 0.06
Page 23 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
6. Connect the appropriate I/O peripherals to the interface cables: keyboard, mouse, Ethernet, monitor, etc.
7. Connect the power cable to power supply
8. Turn on the supply.
Software Installation & Configuration
In general, always refer to the Qseven module’s manual for proper installation of drivers and configuration software; as well as for appropriate BIOS settings.
The following sections provides some specific notes and hints for successful module integration
Operating System Notes
Linux
General
PS/2: Add kernel option i8042.nopnp to ensure keyboard and mouse PS/2 keyboard and mouse operation
Power down: Add kernel option acpi=force to ensure proper software shutdown.
US15W Specific
Graphics: Intel Driver support for the Poulsbo / GMA500) is limited to several distributions (Redhat,
Fedora). See IEGD (Intel Embedded Graphics Driver) website for details http://edc.intel.com/Software/Downloads/IEGD/#compatibility
Other distributions, such as Linux, are supported through the open source community.
Windows
General
Ethernet:
Install the appropriate Ethernet driver from the Qseven module vendor’s website.
US15W Specific
Graphics:
In some cases, the secondary LVDS display will appear washed out, to avoid this ensure the correct version of the IEGD is installed.
Document: CTIM-00058
Revision: 0.06
Page 24 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Cables & Interconnect
The following table summarizes the Xtreme/SBC’s headers and lists the matching cables included with the optional cable kit CKG001.
Location PCB Connector Cable No. Drawing No. Description PCB End Interface End
CBG071 CTIC-00182 USB (dual) P3A, P3B Hirose
DF13-8P-1.25H(50)
P4
P5
MLE
TSHSM-205-D-06-
G-V-L
MLE
TSHSM-205-D-06-
G-V-L
P6
P6
P7
P8
JST
B15B-EH-
A(LF)(SN)
JST
B15B-EH-
A(LF)(SN)
Hirose
DF14-30P-
1.25H(25)
Hirose
DF14-8P-1.25H(50)
P9, P11
P10A,
P10B
P13
J9
P14
MLE
TSHSM-210-D-06-
G-V-L
Molex
470804005
Molex
532610671
Samtec
TMM-102-02-L-S
Hirose
DF13-3P-1.25H(20)
CBG065 CTIC-00181
CBG070 CTIC-00180
GBE
VGA
CBG074 CTIC-00184 ATX Power
CBG075 CTIC-00185 5V / 12V only power
CBG076 CTIC-00196
CBG079 CTIC-00199
LVDS unterminated
SATA
Hirose
DF13A-8S-1.25C
USB 2.0 Type
A Female
2x5 2mm socket RJ45 socket,
GBE Ethernet
2x5 2mm socket VGA HD15
Female
JST
EHR-15
JST
EHR-15
Hirose
DF14-30S-1.25C
SATA
ATX 20 pin male
Molex disk drive power male
N/A
CBG078 CTIC-00198 Backlight unterminated
Hirose
DF13A-8S-1.25C
N/A
CBG073 CTIC-00183 Serial (dual) 2x10 2mm socket 2x DB-9 male
SATA
CBG072 CTIC-00186 Keyboard and
Mouse
Molex
51021-0600
2x 6 Mini-Din
CBG080 CTIC-00200 Power Button 1x2 2mm socket Momentary
Pushbutton
CBG081 CTIC-00201 Fan Power Hirose
DF13A-3S-1.25C
N/A
Document: CTIM-00058
Revision: 0.06
Page 25 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Dimensions
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Document: CTIM-00058
Revision: 0.06
Page 26 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
Xtreme/SBC PCIe/104 Single Board Computer & PCIe/104 Qseven Carrier Board
Users Guide
www.connecttech.com
Specifications
Form Factor
Display
Storage
Serial Interface
USB
Ethernet
Dimensions
Temperature
Power
Power Consumption
Additional I/O
Warranty and Support
PCIe/104, 4 x1 PCIe lanes
VGA, LVDS flat panel
2x SATA (7 pin connector)
2x RS-232, 2x RS-485
4x USB 2.0
1x Gigabit Ethernet
PC/104 compliant
-20ºC to 70ºC (-4ºF to 158ºF)
[1]
ATX supply input
850 mA @ 5V
Qseven carrier circuitry only. Does not include module power.
PS/2 keyboard and mouse
Limited 2-year warranty and free technical support
[1] Temperature range is limited by the SDVO to VGA conversion circuitry.
Document: CTIM-00058
Revision: 0.06
Page 27 of 27
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2017-08-09
advertisement
Related manuals
advertisement