8-1/4” DUAL COMPOUND MITER SAW

WITH LASER GUIDE

*Enhanced Laser

Effect

MODEL: 8320MS

INSTRUCTION MANUAL

COPYRIGHT © 2009 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.

WARRANTY INFORMATION

2-YEAR

LIMITED WARRANTY

8-1/4” DUAL COMPOUND MITER SAW

KING CANADA TOOLS

OFFERS A 2-YEAR LIMITED WARRANTY

FOR NON-COMMERCIAL USE.

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

REPLACEMENT PARTS

Replacement parts for this product are available at our authorized King Canada service centers across Canada.

LIMITED TOOL WARRANTY

King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence or accidents, repairs done by an unauthorized service center, alterations and lack of maintenance. King Canada shall in no event be liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.

To take advantage of this limited warranty, return the product at your expense together with your dated proof of purshase to an authorized King Canada service center. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our authorized service centers. In cooperation with our authorized serviced center, King Canada will either repair or replace the product if any part or parts covered under this warranty which examination proves to be defective in workmanship or material during the warranty period.

KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4

www.kingcanada.com

GENERAL SAFETY INSTRUCTIONS

VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that for the specified tool can result in SERIOUS

INJURY to the user - as well as damage to the tool. If in doubt DO NOT PLUG IN THE TOOL. Using a power source with voltage less is harmful to the motor.

1. KNOW YOUR TOOL

Read and understand the owners manual and labels affixed to the tool. Learn its application and limitations as well as its specific potential hazards.

2. GROUND THE TOOL.

This tool is equipped with an approved 3-conductor cord and a 3-prong grounding type plug to fit the proper grounding type receptacle. The green conductor in the cord is the grounding wire. NEVER connect the green wire to a live terminal.

3. KEEP GUARDS IN PLACE.

Keep in good working order, properly adjusted and aligned.

4. REMOVE ADJUSTING KEYS AND WRENCHES.

Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.

5. KEEP WORK AREA CLEAN.

Cluttered areas and benches invite accidents. Make sure the floor is clean and not slippery due to wax and sawdust build-up.

6. AVOID DANGEROUS ENVIRONMENT.

Don’t use power tools in damp or wet locations or expose them to rain. Keep work area well lit and provide adequate surrounding work space.

7. KEEP CHILDREN AWAY.

All visitors should be kept a safe distance from work area.

8. MAKE WORKSHOP CHILD-PROOF.

Use padlocks, master switches or remove starter keys.

9. USE PROPER SPEED.

A tool will do a better and safer job when operated at the proper speed.

10. USE RIGHT TOOL.

Don’t force the tool or the attachment to do a job for which it was not designed.

11. WEAR PROPER APPAREL.

Do not wear loose clothing, gloves, neckties or jewelry (rings, watch) because they could get caught in moving parts.

Non-slip footwear is recommended. Wear protective hair covering to contain long hair. Roll up long sleeves above the elbows.

12. ALWAYS WEAR SAFETY GLASSES.

Always wear safety glasses (ANSI Z87.1). Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. Also use a face or dust mask if cutting operation is dusty.

13. DON’T OVERREACH.

Keep proper footing and balance at all times.

14. MAINTAIN TOOL WITH CARE.

Keep tools sharp and clean for best and safest performance.

Follow instructions for lubricating and changing accessories.

15. DISCONNECT TOOLS.

Before servicing, when changing accessories or attachments.

16. AVOID ACCIDENTAL STARTING.

Make sure the switch is in the ‘’OFF’’ position before plugging in.

17. USE RECOMMENDED ACCESSORIES.

Consult the manual for recommended accessories. Follow the instructions that accompany the accessories. The use of improper accessories may cause hazards.

18. NEVER STAND ON TOOL.

Serious injury could occur if the tool tips over. Do not store materials such that it is necessary to stand on the tool to reach them.

19. CHECK DAMAGED PARTS.

Before further use of the tool, a guard or other parts that are damaged should be carefully checked to ensure that they will operate properly and perform their intended function. Check for alignment of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other parts that are damaged should be properly repaired or replaced.

20. NEVER LEAVE MACHINE RUNNING

UNATTENDED.

Turn power ‘’OFF’’. Don’t leave any tool running until it comes to a complete stop.

ADDITIONAL SAFETY INSTRUCTIONS

FOR DUAL COMPOUND MITER SAWS

1. WARNING: USE ONLY CROSS-CUTTING SAW BLADES.

WHEN USING CARBIDE TIPPED BLADES, DO NOT USE

BLADES WITH DEEP GUILLETS AS THEY CAN DEFLECT

AND CONTACT GUARD.

23.

PROVIDE adequate support to the sides of the saw table for long workpieces.

2. WARNING: Do not operate the miter saw until it is completely assembled and installed according to the instructions.

25. NEVER use solvents to clean plastic parts. Solvents could possibly dissolve or otherwise damage the material. Only a soft damp cloth should be used to clean plastic parts.

3. IF YOU ARE NOT thoroughly familiar with the operation of compound miter saws, obtain advice from your supervisor, instructor or other qualified person.

26. DISCONNECT power by unplugging tool before changing blade or servicing.

4. BE SURE blade is sharp, runs freely and is free of vibration.

24. NEVER use the miter saw in an area with flammable liquids or gases.

27. DISCONNECT saw from power source before leaving it.

5. ALLOW the motor to come up to full speed before starting cut.

6. KEEP motor air slots clean and free of chips.

28. MAKE SURE the work area is cleaned before leaving the machine.

7. BE SURE blade and flanges are clean and that arbor bolt is tightened securely.

8. ONLY USE blade flanges specified for your saw.

9. NEVER use blades larger or smaller in diameter than 8-1/4”.

10. NEVER apply lubricants to the blade when it is running.

11. ALWAYS check the blade for cracks or damage before operating. Replace cracked or damaged blade immediately.

12. NEVER use blades recommended for operation at less than

6000 RPM.

13. USE the blade guard at all times.

14. ALWAYS keep the lower blade guard in place and operating properly.

15. NEVER reach around or behind saw blade.

16. MAKE SURE blade is not contacting workpiece before switch is turned on.

17. NEVER lock the switch in the "ON" position.

18. IMPORTANT: After completing cut, release power switch and wait for coasting blade to stop before returning saw to raised position.

19. TURN OFF tool and wait for saw blade to stop before moving workpiece or changing settings.

20. DO NOT remove jammed or cut-off pieces until blade has stopped.

21. NEVER cut ferrous metals or masonry.

22. NEVER re-cut small pieces.

ELECTRICAL CONNECTIONS

WARNING!

ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN

SERIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE MITER SAW DISCONNECTED FROM THE

POWER SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY!

POWER SUPPLY

WARNING: YOUR MITER SAW MUST BE CONNECTED TO A 110V,

15-AMP. BRANCH CIRCUIT. FAILURE TO CONNECT IN THIS WAY

CAN RESULT IN INJURY FROM SHOCK OR FIRE.

110V OPERATION

As received from the factory, your miter saw is ready to run for 110V operation. This miter saw is intended for use on a circuit that has an outlet and a plug which looks like the one illustrated in Fig.1.

EXTENSION CORDS

The use of any extension cord will cause some loss of power. Use the following table to determine the minimum wire size (A.W.G-American

Wire Gauge) extension cord. Use only extension cords which accept the tool’s plug.

For circuits that are further away from the electrical circuit box, the wire size must be increased proportionately in order to deliver ample voltage to the motor. Refer to Fig.2 for wire length and size.

110V GROUNDED OUTLET

CURRANT

CARRYING

PRONGS

GROUNDING

PLUG

Tool’s

Amperage

Rating

FIGURE 1

Cord Size in A.W.G.

Cord Length in Feet

25 50 100 150

3-6

6-8

8-10

10-12

12-16

18 16 16 14

18 16 14 12

18 16 14 12

18 16 14 12

14 12 -

FIGURE 2

TOOL SPECIFICATIONS

Model..........................................................................................................................................................................................8320MS

Voltage ............................................................................................................................................................................................110V

Input power..............................................................................................................................................................................10.5 Amp.

No load speed ......................................................................................................................................................................5,500 RPM

Blade size......................................................................................................................................................................8-1/4” x 40 teeth

Arbor size ..........................................................................................................................................................................................5/8”

Miter table angles ............................................................................................................................0

0 , 15 0 , 22.5

0 , 30 0 , 45 0 left and right

Crosscut 90 0 ......................................................................................................................................................................2-1/8” x 4-3/4”

Miter 45 0

Bevel 45 0

(right & left) ........................................................................................................................................................2-1/8” x 3-1/4”

(right & left) ....................................................................................................................................................1-3/16” x 4-3/4”

Dual compound (Miter & Bevel 45 0 right & left) ..............................................................................................................1-3/16” x 3-1/4”

UNPACKING, ASSEMBLY

AND ADJUSTMENTS

UNPACKING

Due to modern mass production techniques, it is unlikely that your King Canada Power tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury.

1. Remove all loose parts from the carton.

2. Remove the packing materials from around the saw.

3. Carefully lift the saw from the carton and place it on a level work surface.

4. The saw has been shipped with the saw head locked in the down position. To release the saw head, push down on the top of the saw arm, pull then turn the the saw head release knob (A) Fig.15.

WARNING: Do not lift the saw while holding on to the guards. Use the top mounted carrying handle.

INSTALLING REAR SUPPORT

Before using this miter saw, it is recommended to install the rear support (A) Fig.3.

During an operation, if the saw head is released accidentally, the saw head will swing upwards, if this rear support is not installed, the entire saw could pivot backwards and possibly create a dangerous situation. Insert the rear support into the two mouting holes at the back of the saw base and secure it in place by tightening screw (B). This rear support should be installed even if this saw is mounted to a workbench.

BENCH MOUNTING

The saw base has holes to facilitate bench mounting.

1. Fix the saw to a bench using 4 hex. bolts and hex. nuts.

2. If desired, you can mount the saw to a piece of 13mm or thicker plywood which can then be clamped to your work support or moved to other job sites and reclamped.

CAUTION: Make sure that the mounting surface is not warped as an uneven surface can cause binding and inaccurate sawing.

Figure 3

INSTALLING DUST BAG

The dust bag (A) Fig.4 fits into the dust bag adaptor (B) at the rear of the saw head.

For more efficient operation, empty the dust bag when it is no more than half full.

This allows better air flow through the bag and improves dust collection.

Figure 4

MITER TABLE LOCK KNOB AND POSITIVE STOPS

For all operations, the miter table must always be locked, the miter table lock knob (A) Fig.5 is used to lock or unlock the table at the desired miter angle. To change the angle of the table, simply turn the saw head, once the table miter angle is set, use the miter lock knob to lock the table.

WARNING! Before making any cut, make sure the miter lock knob is fully tightened.

There are positive stops at 0 0 , 15 0 , 22.5

0 , 30 0 and 45 0 to the left and right. While the table is being rotated, the table will stop at the next positive stop. Once the desired angle is obtained, use the miter lock bouton to lock the table.

Figure 5

ADJUSTMENTS

ADJUSTING FENCE EXTENSION

This miter saw comes with a back fence with a fence extension (A) Fig.6 which slide outwards for additional back support for those long workpieces. Please note that during steep bevel cut operations to the right, this fence extension must be fully extended to not interfere with the motor housing or blade guard.

To adjust the position of the fence extension;

1. Loosen the fence extension socket head screw (B) using hex. key.

2. Slide the fence extension outwards to the desired position and retighten the socket head screw.

ADJUSTING BEVEL ANGLE

This miter saw is capable of dual bevel angles which means the saw head can be tilted towards the right or the left. To adjust the saw head to any bevel angle;

1. Loosen the bevel lock knob (A) Fig.7 and pull the positive stop adjustment pin (B) outwards as shown.

2. At this point, the saw head can be inclined to any angle you desire to the right of the left. If you require a predetermined bevel angle of 0 0 , push the positive stop adjustment pin inwards and pivot the saw head until it stops at

0 0 .

3. Use the bevel angle pointer (A) Fig.8 and bevel scale (B) as a guide to set the bevel angle.

4. Once the desired bevel angle is obtained, it is very important that you retighten the bevel lock knob (A) Fig.7.

SETTING THE BLADE SQUARE WITH THE TABLE

1. Make sure that the electrical plug is removed from the main power supply.

2. Push the saw head down to its lowest position, then pull and turn the head release knob to hold the saw head in the transport position.

3. Loosen the miter lock knob (A) Fig.5. Rotate the table until the pointer is positioned at 0 0 . Retighten the miter lock knob.

4. Loosen the bevel lock knob (A) Fig.7 and set the saw arm at 0 0 bevel (the blade at 90 0 to the miter table). Retighten the bevel lock knob.

5. Place a square (A) Fig.9 against the table and the flat part of the blade body.

NOTE: Make sure that the square contacts the flat part of the saw blade body, not the teeth.

6. Rotate the blade by hand and check the blade-to-table alignment at several points.

7. The edge of the square and the saw blade should be parrallel.

8. If the saw blade angles away from the square, see adjustment procedure on the following page.

Figure 6

Figure 7

Figure 8

Figure 9

ADJUSTMENTS

SETTING THE BLADE SQUARE WITH THE TABLE continued...

If the saw blade angles away from the square, adjust as follows;

9. Loosen hex. nut (A) Fig.10 and unscrew set screw (B) to allow saw head adjustment.

10. Loosen the bevel lock knob (A)Fig.7 and pull the positive stop adjustment pin

(C) Fig.10 outwards.

11. Tilt the saw head until the blade is perfectly parallel with the square, tighten the bevel lock knob (A)Fig.7.

12. Push the positive stop adjustment pin (C) inwards. Tighten set screw (B) up against the positive stop adjustment pin and tighten hex. nut (A) as shown in

Fig.10. Recheck the adjustment, if needed repeat steps 9 to 12.

13. Readjust bevel pointer (A) Fig.8 to line up with the 0º on the bevel scale.

SETTING THE BLADE AT 45 0 WITH THE TABLE

1. Make sure that the electrical plug is removed from the main power supply.

2. Push the saw head down to its lowest position, then pull and turn the head release knob to hold the saw head in the transport position.

3. Loosen the miter lock knob (A) Fig.5. Rotate the table until the pointer is positioned at 0 0 . Retighten the miter lock knob.

4. Loosen hex. nut (A) Fig.11 and tighten cap screw (B) for right tilt adjustment or hex. nut (C) and tighten cap screw (D) for left tilt adjustment.

5. Loosen the bevel lock knob (A)Fig.7 and pull the positive stop adjustment pin (C)

Fig.10 outwards. Set the saw arm at 45 0 bevel. Retighten the bevel lock knob.

6. Place a 45 0 square against the table and the flat part of the blade body.

Figure 10

NOTE: Make sure that the square contacts the flat part of the saw blade body, not the teeth.

7. Rotate the blade by hand and check the adjustment at several points.

8. The edge of the square and the saw blade should be parrallel.

9. If the saw blade angles away from the square, adjust as follows;

10. Loosen the bevel lock knob (A) Fig.7.

11. Tilt the saw head until the blade is perfectly parallel with the square, tighten the bevel lock knob (A) Fig.7.

12. Adjust cap screw (B) for right tilt adjustment or cap screw (D) for left tilt adjustment by raising the cap screw up against the bevel support and tighten hex. nut (A) Fig.11 for right tilt adjustment or hex. nut (C) for left tilt adjustment.

Recheck the adjustment, if needed repeat steps 10 to 12.

13. Readjust bevel pointer (A) Fig.8 to line up with the 45º on the bevel scale.

Figure 11

SETTING THE FENCE SQUARE WITH THE BLADE

1. Make sure that the electrical plug is removed from the main power supply.

2. Push the saw head down to its lowest position, then pull and turn the head release knob to hold the saw head in the transport position.

3. Loosen the miter lock knob (A) Fig.5. Rotate the table until the pointer is positioned at 0 0 . Retighten the miter lock knob.

Figure 12

4. Loosen the bevel lock knob (A) Fig.7 and set the saw arm at 0 0 bevel (the blade at 90 0 to the miter table). Tighten the bevel lock knob.

5. Place a square (A) Fig.12 against the fence (B) and the flat part of the blade.

NOTE: Make sure that the square contacts the flat part of the saw blade, not the teeth.

6. The edge of the square and the fence should be parrallel.

7. If the fence angles away from the square, adjust as follows;

8. Remove the fence extension (A) Fig.6 and cap screw (B) Fig.6. Loosen the now exposed fence cap screws (C) Fig.12 on both sides and position the fence against the square and retighten all cap screws.

9. Reinstall fence extension.

ADJUSTMENTS & OPERATIONS

USING THE LASER GUIDE SYSTEM

The laser guide system is controlled by the laser guide push button switch (A)

Fig.13 and will only turn on when the miter saw is plugged into a power source.

Warning! Do not stare directly into the laser beam.

1. Mark the cut line on your workpiece.

2. Adjust the miter and/or bevel angles as required.

3. Turn laser on and align the cut line of your workpiece with the laser guide beam taking into consideration the blade thickness (blade kerf) before making cut.

4. Start the motor y pressing the trigger (B) Fig.13.

5. When the blade reaches its maximum speed (approx. 2 sec.), lower the blade through the workpiece.

ADJUSTING LASER GUIDE SYSTEM

If your laser guide does not seem to be aligned with the edge of the blade kerf, a small adjustment can be made.

1. Remove the laser guide protective cover by pulling it off.

3. Place a scrap piece of wood on the table. Turn on miter saw and make a partial cut to indicate the blade kerf in the piece of wood.

3. Turn the laser guide on.

4. Two adjustments are possible, a lateral and a diagonal adjustment. The lateral adjustment involves moving the laser guide support (A) Fig.14 sideways to align the laser with the blade, this is done by loosening the two pan head screws (B)

Fig.14 above the laser (C). The diagonal adjustment involves rotating the laser itself to align the laser with the blade, this is done by loosening pad head screw

(D).

5. Once properly adjusted, hold laser tip and laser guide support and retighten pan head screws (B & D) to prevent the laser assembly from moving.

6. Reinstall the laser guide protective cover.

CUTTING OPERATIONS

CROSSCUTTING

A crosscut is made by cutting across the grain of the workpiece. A 90 0 crosscut is made with the miter and the bevel angles set at 0 0 .

1. Pull and turn the saw head release knob (A) Fig.15 and lift the saw head to its full height.

2. Loosen the miter lock knob (A) Fig.5. Rotate the miter table until the pointer aligns with the 0º. Retighten the miter lock knob.

WARNING: Be sure to tighten the miter lock knob before making a cut. Failure to do so could result in the table moving during the cut and serious personal injury.

3. Place the workpiece flat on the table with one edge securely against the fence.

If the board is warped, place the convex side against the fence. If the concave side is place against the fence, the board could break and jam the blade.

4. When cutting long pieces of timber, support the opposite end of the timber with an additional roller stand or a work surface that is level with the saw table.

5. Use a vise or clamp to secure the workpiece whenever possible.

6. Before turning on the saw, perform a dry run of the cutting operation to check that there are no problems.

7. Hold the trigger handle firmly and squeeze the trigger (B) Fig.13. Allow the blade to reach maximum speed.

8. Slowly lower the blade into and through the workpiece.

9. Release the switch trigger and allow the saw blade to stop rotating before raising the blade out of the workpiece. Wait until the blade stops before removing the workpiece.

Figure 13

Figure 14

Figure 15

OPERATIONS

BEVEL CUT

A bevel cut is made by cutting across the grain of the workpiece with the blade angled to the fence and miter table. The miter table is set at the

0º position and the saw head is set at an angle between 0 0 and 45 0 to the right or to the left.

1. Pull and turn the saw head release knob (A) Fig.15 and lift the saw head to its full height.

2. Loosen the miter lock knob (A) Fig.5. Rotate the miter table until the pointer aligns with the 0º. Retighten the miter lock knob.

WARNING: Be sure to tighten the miter lock knob before making a cut. Failure to do so could result in the table moving during the cut and serious personal injury.

3. Loosen the bevel lock knob (A) Fig.7 and move the saw arm to the desired bevel angle (between 0 0 and 45 bevel lock knob. Before tilting the saw arm towards the left, pull positive stop adjustment pin (B) Fig.7.

0 to the right or left). Retighten the

4. Place the workpiece flat on the table with one edge securely against the fence. If the board is warped, place the convex side against the fence.

If the concave side is place against the fence, the board could break and jam the blade.

5. When cutting long pieces of timber, support the opposite end of the timber with an additional roller stand or a work surface that is level with the saw table.

6. Use a vise or clamp to secure the workpiece whenever possible.

7. Before turning on the saw, perform a dry run of the cutting operation to check that there are no problems.

8. Hold the trigger handle firmly and squeeze the trigger (B) Fig.13. Allow the blade to reach maximum speed.

9. Slowly lower the blade into and through the workpiece.

10. Release the switch trigger and allow the saw blade to stop rotating before raising the blade out of the workpiece. Wait until the blade stops before removing the workpiece.

COMPOUND CUT

A compound cut involves using a miter angle and a bevel angle at the same time. It is used in making picture frames, to cut mouldings, making boxes with sloping sides and for roof framing. Always make a test cut on a piece of scrap wood before cutting into good material.

1. Pull and turn the saw head release knob (A) Fig.15 and lift the saw head to its full height.

2. Loosen the miter lock knob (A) Fig.5. Rotate the miter table until the pointer aligns with the desired angle on the miter scale. Retighten the miter lock knob.

WARNING: Be sure to tighten the miter lock knob before making a cut. Failure to do so could result in the table moving during the cut and serious personal injury.

3. Loosen the bevel lock knob (A) Fig.7 and move the saw arm to the desired bevel angle (between 0 0 and 45 bevel lock knob. Before tilting the saw arm towards the left, pull positive stop adjustment pin (B) Fig.10.

0 to the right or left). Tighten the

4. Place the workpiece flat on the table with one edge securely against the fence. If the board is warped, place the convex side against the fence.

If the concave side is placed against the fence, the board should break and jam the blade.

5. When cutting long pieces of timber, support the opposite end of the timber with an additional roller stand or a work surface that is level with the saw table.

6. Use a vise or clamp to secure the workpiece whenever possible.

7. Before turning on the saw, perform a dry run of the cutting operation to check that there are no problems.

8. Hold the trigger handle firmly and squeeze the trigger (B) Fig.13. Allow the blade to reach maximum speed.

9. Slowly lower the blade into and through the workpiece.

10. Release the trigger and allow the saw blade to stop rotating before raising the blade out of the workpiece. Wait until the blade stops before moving the workpiece.

REPLACING/INSTALLING BLADE

REPLACING/INSTALLING BLADE

DANGER!

• Never attempt to use a blade larger than the stated capacity of the saw (8-1/4”).

It will come into contact with the blade guards and housing.

• Never use a blade that is too thick to allow the outer blade flange to engage with the flats on the spindle. It will prevent the blade screw from properly securing the blade on the spindle.

• Do not use this saw to cut metal or masonry.

1. Make sure that the power cord is removed from the main power supply.

2. Push down on the saw arm and pull and turn the saw head release knob to disengage the saw head.

3. Raise the saw head to its highest position.

4. Unscrew and remove large screw (A) Fig.16, and move the blade guard pivot link arm (B) out of the way. Unscrew and remove pan head screw (C) which fixes the guard plate and lower blade guard to the upper blade guard.

5. Once pan head screw (C) is removed, swing the guard plate and lower blade guard upwards to allow access to the blade bolt (B) as shown in Fig.17.

Figure 16

6. Completely depress the spindle lock button (A) Fig. 18 using one hand. Rotate the blade by hand until the spindle locks.

7. Use the blade hex. key (A) Fig.17 supplied to remove the blade bolt (B), loosen in a clockwise direction as the blade bolt has a left hand thread.

8. Remove the outer blade flange (C) and the blade.

9. Wipe a drop of oil onto the inner and outer blade flanges.

10. Fit the new blade onto the spindle, make sure that the blade has the appropriate arbor size (5/8”) and that the inner blade flange sits properly behind the blade.

CAUTION: Always install the blade with the blade teeth pointing downwards towards the fence as shown in Fig.17. The direction of the blade rotation is also stamped with an arrow on the upper blade guard.

11. Reposition the outer blade flange.

12. Depress the spindle lock, reposition and secure the blade bolt using the blade hex. key. Tighten the blade bolt in a counterclockwise direction as the blade bolt has a left hand thread.

13. Reposition the lower blade guard and guard plate and secure the guard plate with pan head screw and large screw removed in step 4.

Figure 17

Figure 18

MAINTENANCE

MAINTENANCE

All the ball bearings are sealed and lubricated for life and will require no maintenance.

Cleaning

• After use, wipe off chips and dust adhering to the tool with cloth or the like.

Keep the blade guards and covers clean. Lubricate moving parts with machine oil to prevent rust.

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustments should be performed by your nearest authorized service center.

REPLACING CARBON BRUSHES

Remove and check the carbon brushes regularly (normally after 50 hours of use). The carbon brushes are installed inside the motor housing. Using a screwdriver, remove the 2 pan head screws (A) Fig.19 that hold the motor housing cap (B) in place.

Once the motor housing cap is removed, remove cap screw (A) Fig.20 which holds the back end of the carry handle. Disconnect the carbon brush wire (B) from the terminal. To release the carbon brush from the holder, lower the retaining spring (C) using a small screwdriver.

To remove and inspect the upper carbon brush (only), it is required to slightly lift the back end of the carry handle (A) Fig.21 to clear the upper carbon brush.

Remove the upper carbon brush (B) from the motor housing and inspect it.

Repeat for the lower carbon brush. Carbon brushes need to be replaced once they wear down to their limit mark, see Fig.22. Keep the carbon brushes clean and free to slip in the holders.

If they have worn down to the limit mark, purchase a set of identical replacement carbon brushes (both carbon brushes should be replaced at the same time). Insert new carbon brushes into the holders, connect them to the terminals, reposition the retaining springs and reinstall the motor housing cap using the 2 pan head screws.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.

Figure 19

Figure 20

Figure 21

Carbon brush limit mark

Figure 22