Table of Contents
Important Safeguards
Introduction
Installation
Operation
Cleaning Pattern
Automatic Shutoff and Removal
Maintenance
Warranty
2
3
4
5
5
6
6
8
!
WARNING:
To reduce the risk of fire, electrical shock, injury,
or damage to your product or to bathers:
!
Do not use if unit is damaged in any way.
!
Use this product only for its intended use as
described in this manual.
!
Unit must be submerged in water to operate
properly.
!
When not in use, store indoors in a clean, dry place.
Do not leave underwater, in direct sunlight, or
exposed to extreme temperatures.
!
Make sure Robo-Kleen is unplugged from its power
supply before cleaning, replacing the filter or any
other routine maintenance.
!
To protect risk of electrical shock, do not put the
transformer in water or other liquid.
!
2
To avoid damage to the transformer and cord, never
carry the transformer by the cord or yank to
disconnect from an outlet. Instead, disconnect by
pulling the plug itself from the outlet. Do not pull
cord around sharp corners or edges.
!
Do not operate with a damaged cord or transformer.
Do not use with extension cord.
!
Disconnect transformer from outlet when not in use.
!
If cleaner is not working as it should or has been
dropped or damaged in any way, contact SmartPool
customer service before using.
Congratulations on your purchase! You will find RoboKleen to be the most effective pool cleaner available.
Unlike water-powered cleaners, which put all dirt and debris
through your existing pool pump and filter, Robo-Kleen has
its own pump and filter system. This saves you money in
electricity costs and extends the life of your existing pool
equipment.
Read carefully before using your Robo-Kleen pool cleaner.
Power Supply
Connect to 110V
GFCI Outlet
Connect to the
Cleaner
Power On/Off
Switch
Mobile Cleaning Unit
Filtered Water
Outlet
Connect to
Power Supply
Steering
Wheels
Drive
Wheels
Water Escape
Door
Side Handle
3
Underside of Mobile Cleaning Unit
Locking Tabs
Suction Ports
Cleaning Brushes
Locking Tabs
Installation
The power supply should be positioned so that Robo-Kleen can reach all the
walls of the swimming pool and must be at a minimum distance of 10 feet from
the edge of the pool.
CAUTION: INSURE THE THE 110V MAIN LINE OUTLET IS PROTECTED BY A
GROUND FAULT CIRCUIT INTERRUPTER (GFCI) OR EARTH LEAKAGE CIRCUIT
INTERRUPTER (ELCI). OTHERWISE, DEATH OR INJURY CAN RESULT.
!
DO NOT ALLOW POWER SUPPLY TO BECOME SUBMERGED IN POOL.
DEATH OR INJURY CAN RESULT. DO NOT PLACE ON EDGE OF POOL.
POWER SUPPLY MUST NOT FALL INTO POOL!
To connect Robo-Kleen to the power supply,
remove the cap on the transformer output socket.
Plug the Robo-Kleen cord into the socket. Notice
the plug and socket are indexed using pins.
Tighten the threaded plug cover so that the cord is
securely attached.
4
Operation
!
DO NOT ENTER THE SWIMMING POOL WHILE ROBO-KLEEN
IS IN OPERATION TO AVOID ENTANGLEMENT WITH CORD
a. Connect the cable to the power supply
b. Grasp the cleaner by a side handle and place Robo-Kleen in the pool.
c. Rock the unit from front to back and side to side, releasing trapped air, until the
unit slowly sinks to the bottom of the pool.
d. Start the unit at a 90˚ angle to a wall . CAUTION: BE SURE MAIN LINE OUTLET IS
PROTECTED BY A GROUND FAULT CIRCUIT INTERRUPTER (GFCI) DEATH OR
SERIOUS INJURY COULD OCCUR.
e. Press the top of the On/Off switch through the clear jacket on the power supply.
Robo-Kleen will take an initial 10 seconds to scan the circuit board and reset the
memory. After the initialization is complete, filtered water will be pumped to the
top and the unit will start moving.
CAUTION: Do not operate Robo-Kleen out of the water. This may result in damage
to the pump motor seals and invalidate the warranty. Optimum water
temperature for the operation of Robo-Kleen is 65˚ F to 85˚ F (18˚ C to 29˚ C). Do
not operate Robo-Kleen when water temperature exceeds 90˚ F (32˚ C).
Cleaning Pattern
Robo-Kleen features an exclusive Controlled Tandem design, which allows the steering
wheels to move together without locking into one position. This feature, combined
with interval timing in the software, which randomly changes the direction of RoboKleen, further enhances movement around the pool.
This eliminates the “back and forth” pattern that can occur when wheels are locked
into position with fixed timing runs. Robo-Kleen’s ability to change direction easily
and often results in coverage of the entire pool quickly.
Another benefit of the Controlled Tandem design is that the cleaner does not continually
move in one direction around the pool. This minimizes coiling of the cord.
For round
pools, factory
preset angle
is best.
For oval
pools, remove
limit screw for
greater angle
of tandem
wheels.
5
Automatic Shutdown and Removal
Robo-Kleen will automatically shut down after a work cycle of approximately 3
hours. Switch off the power supply for at least 30 seconds before restarting.
ALWAYS SWITCH OFF THE POWER SUPPLY BEFORE REMOVING ROBO-KLEEN
FROM THE POOL.
Remove Robo-Kleen from the water by GENTLY AND SLOWLY pulling in the
cable. WHEN ROBO-KLEEN REACHES THE SURFACE, LIFT IT OUT BY THE
HANDLE - NOT BY THE CABLE. To minimize debris falling back into the pool
during removal, when the cleaner reaches the surface, QUICKLY GRASP A
HANDLE AND TURN UNIT OVER TO REST UPSIDE-DOWN ON TOP LEDGE.
ALLOW WATER TO DRAIN OUT THE TOP.
Carefully reel in and coil the cable. Store Robo-Kleen in a dry shaded place at a
temperature between 40˚ F and 90˚ F (5˚ C and 32˚ C).
Maintenance
!
ALWAYS SWITCH OFF POWER SUPPLY BEFORE PERFORMING MAINTENANCE.
There are only a few simple steps to maintaining your Robo-Kleen.
1) Uncoiling cable
If cable becomes twisted, unplug from power supply and untwist manually.
Untwisting manually is most effective after allowing cable to lay in the sun so
it becomes pliable.
2) Clean Filter Bag
a. Place Robo-Kleen upside down.
Push the locking tabs to the side to
unlock the bottom lid. Remove the
bottom lid with filter bag attached.
6
b. Pull one of the 4 red tabs out and remove the filter
bag from the bottom lid. Turn the filter bag inside
out. Use a garden hose to wash it thoroughly. The
bag should be laundered periodically, using a
regular wash cycle.
c. Rinse the bottom lid parts and bottom brushes.
d. Refit the filter bag with the fluffy surface inward.
Start from one corner - align one of the red tabs
with the corner. Gently insert the stitched edge of
the filter bag into the double walls (groove) of the
bottom lid, and work your way around.
e. Replace the bottom lid assembly in the body of the
unit and lock in place.
3) Impeller
Occasionally hair or linen may get caught in the impeller. If that happens, take
the top grill off by removing the 2 screws from the top. MAKE SURE THE
TRANSFORMER IS UNPLUGGED. Remove the debris. Replace the top grill
and tighten the 2 screws.
4) Front Drive Wheels and Rear Idler Wheels
Remove debris or tree leaves caught in the axle bearing. CAUTION: Do not
turn the drive wheels by force. This may cause damage to the drive gear train.
5) Winterization
Always remove cleaner from pool for winterization. Do not store Robo-Kleen
where the temperature drops below 40˚ F. Freezing temperatures can affect
seals and lubricants used in the mechanism.
7
TWELVE MONTH LIMITED WARRANTY
Twelve month limited warranty in Continental USA only from date of original purchase for
manufacturing defects under normal and reasonable use, and subject to the maintenance
requirements and installation guidelines set forth in the product instruction manual.
Electronics Products
THIS WARRANTY IS SUBJECT TO THE TERMS, LIMITATIONS AND EXCLUSIONS DESCRIBED
BELOW, AND THERE ARE NO OTHER WARRANTIES OR REPRESENTATIONS, EITHER EXPRESS
OR IMPLIED, WHETHER OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
OTHER, MADE BY THE MANUFACTURER, OTHER THAN THOSE SPECIFICALLY SET FORTH IN
THIS WRITTEN WARRANTY
What is Covered: SmartPool, Inc. warrants its electronic product to be free from defects in material and
workmanship when leaving the factory.
What is not Covered: Any type of damage to the product due to improper installation, maintenance, or failure to
provide necessary and reasonable maintenance; any damage or injury caused by misuse and/or unreasonable use of
the product; batteries (if applicable); damage due to or related to improper draining, winterizing, storage or Acts of
God; SmartPool, Inc. will not honor any claims for damage to any products in transit unless damage to the shipping
container is noted at the time of delivery on the transfer company’s delivery bill.
THE WARRANTY OBLIGATIONS OF SMARTPOOL, INC. ARE LIMITED TO REPAIR OR
REPLACEMENT OF THE PRODUCT OR OF ANY DEFECTIVE COMPONENT, AT THE OPTION OF
SMARTPOOL. SUCH REPAIR OR REPLACEMENT MAY INCLUDE THE USE OF REFURBISHED
COMPONENTS AND/OR UNITS AT THE OPTION OF SMARTPOOL. UNDER NO CIRCUMSTANCES
WILL SMARTPOOL, INC. BE LIABLE OR RESPONSIBLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES, AND/OR CHARGES FOR LABOR. SMARTPOOL SHALL NOT BE LIABLE
OR RESPONSIBLE UNDER ANY CIRCUMSTANCES OR ANY AMOUNT FOR ANY CONSEQUENTIAL
OR INCIDENTAL DAMAGES, OR FOR ANY INJURIES OR DAMAGES TO PERSON OR PROPERTY
USING OR USED IN CONNECTION WITH THE PRODUCT, OR FOR ANY OTHER LOSS OF PROFITS
OR OTHER COSTS OR EXPENSES OF ANY KIND OR CHARACTER. IF SMARTPOOL, INC.
DETERMINES THAT EITHER REPAIR OR REPLACEMENT OF THE PRODUCT IS NECESSARY,
SMARTPOOL MAY EITHER REPAIR THE PRODUCT AT A NOMINAL CHARGE TO THE OWNER OR
REPLACE THE PRODUCT. THE OWNER BEARS THE SOLE RESPONSIBILITY FOR PRE-PAID
RETURN OF THE PRODUCT TO SMARTPOOL, AND ALL REPAIRED OR REPLACED PRODUCTS
WILL BE RETURNED AT THE OWNER’S EXPENSE.
NO PERSON, FIRM, OR CORPORATION IS AUTHORIZED TO MAKE REPRESENTATIONS OR INCUR
ANY OBLIGATIONS IN THE NAME OF OR ON BEHALF OF SMARTPOOL, INC., EXCEPT AS STATED
HEREIN. THE REMEDIES SET FORTH IN THIS WARRANTY ARE EXPRESSLY UNDERSTOOD TO BE
THE EXCLUSIVE REMEDIES AVAILABLE TO THE OWNER, AND THIS WARRANTY CONTAINS THE
FULL AND COMPLETE AGREEMENT BETWEEN SMARTPOOL, INC. AND THE OWNER. THIS
WARRANTY SETS FORTH THE ONLY OBLIGATIONS OF SMARTPOOL, INC., WITH REGARD TO
THIS PRODUCT, AND THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF.
The representations set forth herein are the only representations made by SmartPool, Inc., with respect to
the product, and this warranty does not constitute either a performance or satisfaction guarantee. It is the
responsibility of the product owner to regularly test and check the product for proper function and safety.
This warranty gives the original owner specific legal rights. You may have other rights depending on where
you live.
What you must do to file a claim: Call 1-732-730-9880 to initiate a claim.
CAUTION:
Some vinyl liners are more susceptible to surface wear or pattern removal than others,
caused by objects, such as brushes, floats, toys, chlorine dispensers, and automatic pool
cleaners, coming into contact with the vinyl surface. Such patterns can be severely
scratched or abraded merely by rubbing the surface with a brush. Pattern ink can also rub
off when it comes into contact with objects in the pool. SmartPool, Inc. is not responsible
for, nor does this limited warranty cover, pattern removal, abrasion, markings on or damage
of any kind to vinyl liners.
">
