4-547-917-11(1) Digital HD Video Camera Recorder/ Live-View Remote Attaching a belt to Live-View Remote Getting Started Charging the battery pack for the camera 1 Place the remote control on the base plate and thread the belt through the belt loop of the remote control and the base plate as illustrated in , and then attach it as illustrated in . 3 Press the UP button or DOWN button of the remote control to select the desired setting, then press the REC/ENTER button. For more details about the setting items, refer to the online Help Guide. http://rd1.sony.net/help/cam/1410/h_zz/ Open the cover. Slide the lock lever to the OPEN side. Open the cover from . Operating Guide Disconnect Help Guide (Web manual) This manual describes available operation methods with the HDR-AZ1 itself and the supplied Live-View Remote RM-LVR2V. “Help Guide” is an on-line manual. You can read the Help Guide on your computer or smartphone. Play Mode Shooting Mode http://rd1.sony.net/help/cam/1410/h_zz/ You can download the movie editing PC software “Action Cam Movie Creator,” limited to this device, from the following URL. http://www.sony.net/actioncam/support/ See how to use the camera and software at this URL. 2 Insert the battery pack. Align the mark of the battery with that of the camera Setting items Disconnect the Wi-Fi connection and return to the Wi-Fi device selection screen Play and delete images using the remote control Switching between Movie/Photo/ Interval Photo Image quality setting SteadyShot •You can adjust the belt length depending on the pasting position of and . •To fasten the remote control to your arm, wear the remote control with the LCD screen parallel to the back of your hand and the REC/ ENTER button facing toward your fingertips. Thread the belt through as illustrated on the left below. After attaching , move to cover the end of . Flip Movie settings Scene Color setting Movie record format Flip Scene Continuous shooting Still image settings Continuous shooting interval •Use an SDXC card faster than Class10 when recording movies in XAVC S. Place the battery on the battery ejection sheet and insert the battery pack Insert the battery pack, aligning the mark of the battery with that of the camera and orienting its printed side, as illustrated HDR-AZ1/RM-LVR2V Securely close the cover and slide the lock lever to the LOCK position. Make sure that the yellow mark on the lock lever is not visible and the cover is securely closed. Double check that the battery ejection sheet is not pinched in the cover or sticking out of the cover. If any foreign matter such as sand gets inside the cover, the sealing gasket may be scratched, and may result in water entering the inside of the camera. English Owner’s Record The model and serial numbers are located on the side. Record the serial number in the space provided below. Refer to these numbers whenever you call your Sony dealer regarding this product. Model No. HDR-AZ1 Serial No. The model and serial numbers are located on the bottom. Record the serial number in the space provided below. Refer to these numbers whenever you call your Sony dealer regarding this product. Time lapse Time code/User bit setting Be sure that the Multi terminal cover of the remote control is closed. To close the cover, perform the operations in step 1 in opposite order. To eject the battery, pull the battery ejection sheet. There are chances that the battery may not be ejected if the battery ejection sheet is stored under the battery. Additionally, this may cause water leakage. Precaution 3 Check that the power of the camera is OFF. •Securely close the terminal cover until the yellow mark under the lock lever can no longer be seen. If any foreign matter such as sand gets inside the terminal cover, the sealing gasket may be scratched, leading to water entering the remote control. 2 Press the ON/OFF button. Connect the camera to an activated computer with the micro USB cable (supplied). Lights in orange while charging •When the remote control is turned on for the first time, the date and time setting screen is displayed. •To turn off the remote control, press the ON/OFF button again. 3 Set the date and time. •Press the UP button or DOWN button to select the desired item, then press the REC/ENTER button. •Press the UP button or DOWN button to select the desired setting, then press the REC/ENTER button to confirm. © 2014 Sony Corporation Printed in China Checking the bundled items Camera (1) Live-View Remote RM-LVR2V (1) Micro USB cable (1) Rechargeable battery pack (NP-BY1) (1) Waterproof Case (SPK-AZ1) (1) Attachment Buckle (1) Flat Adhesive Mount (1) Curved Adhesive Mount (1) Tripod Adaptor (1) Set of printed documentation Parts and controls Camera POWER lamp/CHG (Charge) lamp REC HOLD switch REC (Movie/Photo) button REC lamp/LIVE lamp Lens Microphones Tripod adaptor attachment hole (N mark) NFC: Near Field Communication Speaker IR remote receiver Display panel ON/OFF button Wi-Fi button Connector cover (USB) Multi/Micro USB terminal Supports Micro USB compatible devices. RESET button Memory card insertion slot Memory card cover REC/Access lamp Battery cover lock lever Battery ejection sheet Battery storage area Battery pack cover SSID label Live-View Remote MENU button DISP button GPS antenna REC/ENTER button REC/Wi-Fi lamp LCD screen DOWN button UP button CHG (Charge) lamp RESET (Reset) button Multi/Micro USB terminal Lock lever Connector cover (USB) ON/OFF button Loop for a belt Remote control settings Recording 1 Slide the REC HOLD switch of the camera and release REC HOLD. If REC HOLD of the camera is released, proceed to step 2. 2 Press the REC button of the camera or the remote control to start recording. •The REC/Wi-Fi lamp of the remote control changes from blue to red. Press the REC button of the camera or the remote control again to stop recording. Inserting a memory card Printed side ¦¦ Notes •Types of icons displayed in each setting screen differ depending on the shooting mode and recording mode of the camera to be connected. •To return to the setting item selecting screen from the setting value selecting screen, select . 3 Micro USB cable microSD card/ microSDHC card/ microSDXC card Screen rotation Monitor brightness Date & time setting Reset settings Version Connection mode GPS setting Airplane mode Reset network settings Attach accessories to the camera, as required. For details on the bundled accessories, refer to the following. http://rd1.sony.net/help/cam/1415/h_zz/ To turn off the camera, press the ON/OFF button until the POWER lamp turns off. 4 IR-remote controller Switching NTSC/PAL Auto power off Beep Format Connecting devices settings ¦¦ Notes •Attaching the belt incorrectly may cause injury. •A GPS antenna is built in the front of the remote control. Placing the remote control upside down may cause positioning to take long time or may not be able to determine your position. •When placing the remote control on your right wrist, set the screen rotation in the remote control settings to ON. •When using the remote control attached to your arm, always attach the supplied base plate and belt correctly. •Be careful not to drop the remote control when unfastening the belt. 1 Model No. RM-LVR2V Serial No. The nameplate is located on the bottom exterior. If you need to check it, detach the belt. Interval shooting settings Turning on the power of the Live-View Remote Owner’s Record Self-timer Flip Scene Memory Stick Micro™ (Mark2) media Terminal side Insert the memory card properly, confirming each side is facing the correct direction. *Use an SDXC card faster than Class10 when recording movies in XAVC S. ¦¦ Notes •Operation with all memory cards is not assured. •Confirm the direction of the memory card. If you forcibly insert the memory card in the wrong direction, the memory card, memory card slot, or image data may be damaged. •Format the memory card before use. •To eject the memory card, lightly push the memory card once. •Make sure that the connector cover (USB), the memory card cover and the battery pack cover are securely closed and any foreign matters are not stuck in the cover before use. Otherwise, this may cause water leakage. •The data and time setting is complete. Press the DISP button to check the date and time that you have set as illustrated below. Checking the camera settings 1 2 Turn on the power of the camera. Check that a [Wi-Fi] mark is displayed on the display panel of the camera. Operating by smartphone You can operate the camera with your smartphone as well as the bundled remote control. Installing PlayMemories Mobile™ on your smartphone Android OS Single connection Refer to the instruction manual on the website on how to use (Multi connection) and (Live connection). http://rd1.sony.net/help/cam/1410/h_zz/ Check that the power of the remote control is OFF. Connect the remote control to an activated computer with the micro USB cable (supplied). ¦¦ Notes •Playback of images recorded with other cameras, is not assured on this camera. •Images cannot be played on the camera. To play back images, you need a smartphone or tablet supporting a dedicated application, PlayMemories Mobile. •The camera cannot play back audio. •During periods of extended shooting, the camera's temperature may rise to a point where shooting stops automatically. •If a [Wi-Fi] mark is not displayed or is displayed on the [Wi-Fi] mark, press the Wi-Fi button until only the [Wi-Fi] mark is displayed. Charging the Live-View Remote 1 2 •The REC/Wi-Fi lamp of the remote control changes from red to blue. Connecting the Live-View Remote and a camera by Wi-Fi 1 2 Search for PlayMemories Mobile on Google Play, then install it. •When using One-touch functions (NFC), Android 4.0 or later is required. iOS Search for PlayMemories Mobile on App Store, then install it. Turning on the power of the camera and remote control. •When using iOS, One-touch functions (NFC) are not available. The Wi-Fi device selection screen is displayed on the LCD screen of the remote control. Select the SSID of the camera you want to connect with the UP button or DOWN button and press the REC/ENTER button to confirm. The CHG (Charge) lamp of the remote control lights up in orange and charging begins. The CHG (Charge) lamp goes out when charging is completed. ¦¦ Notes •You can charge the remote control even if it is not completely discharged. Also, even if the remote control is not fully charged, you can use the partial charge capacity of the battery pack as is. •When the power of the remote control is on, it is supplied with power but not charged. •The camera and remote control enter the waiting state for Wi-Fi certification. When you hear a beep sound at a long interval, press and hold the Wi-Fi button. The beep sounds at a short interval, and then connection is completed. •The display on the LCD screen of the remote control switches to the Live-View display and the REC/Wi-Fi lamp of the remote control lights up in blue. The camera and remote control are now connected to your camera through Wi-Fi. ¦¦ Notes •Update PlayMemories Mobile to the latest version if you have already installed it on your smartphone. •The Wi-Fi function described in this Operating Guide is not guaranteed to work with all smartphones and tablets. •The operation methods and display screens for the application are subject to change without notice by future upgrades. •For more information about PlayMemories Mobile, refer to the following website. (http://www.sony.net/pmm/) Connecting Android Turn on the power of the camera. Start PlayMemories Mobile on the smartphone. Select the SSID, as printed on the sticker attached to the back side of the battery cover. Input the password on the same sticker (First time only). Setting You can set the camera’s settings by pressing the MENU button of the remote control while the camera and remote control are connected through Wi-Fi. 1 2 Press the MENU button of the remote control. The list of setting items will be displayed. Press the UP button or DOWN button of the remote control to select the desired item to set, then press the REC/ENTER button. Android (Supporting NFC) Touch the (N mark) of the smartphone against the (N mark) of the camera. When PlayMemories Mobile starts, settings are automatically applied to establish Wi-Fi connection. iPhone CAUTION About the water-proof performance of the remote control Live-View Remote Turn on the power of the camera. Open [Settings] on the smartphone. Select [Wi-Fi] on the smartphone. Select the SSID, as printed on the sticker attached to the back side of the battery cover. Input the password on the same sticker (First time only). Confirm that the SSID of the camera is displayed on the smartphone. Return to the Home screen, then start PlayMemories Mobile. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. The remote control is designed to be water-proof. Damage caused by misuse, abuse, or improper maintenance is not covered by the limited warranty. •Do not subject the remote control to pressurized water, such as from a tap. •Do not use in hot springs. •Use the remote control in the water temperature range of 0 °C to 40 °C (32 °F to 104 °F). Power requirements:Rechargeable battery pack: 3.6 V (Internal battery) Multi/Micro USB terminal: 5.0 V USB charging: DC 5.0 V, 500 mA/800 mA Rechargeable battery pack: Maximum charge voltage: DC 4.2 V Maximum charge current: 1.89 A Waterproof performance: Depth of water 3 m (10 feet), 30 minutes continuously (The waterproof performance is not guaranteed under all circumstances) Operating temperature: -10 °C to +40 °C (14 °F to +104 °F) Storage temperature:-20 °C to +60 °C (-4 °F to +140 °F) Dimensions (Approx.): 72.3 mm × 50.2 mm × 20.8 mm (2 7/8 in. × 2 in. × 27/32 in.) (W/H/D, excluding protrusions) Mass: Approx. 67 g (2.4 oz) (only the main body) Total weight (when in use): Approx. 98 g (3.5 oz) (including the supplied belt and base plate) •Design and specifications of the camera, remote control and accessories are subject to change without notice for future upgrade. •For more specifications, refer to the Help Guide (WEB). Checking without a sticker If the sticker is peeled off or becomes difficult to be read, you can recall your user ID and password by the following procedure. Insert a charged battery pack into the camera. Connect the camera to a computer with the micro USB cable (supplied). Press the ON/OFF button to turn on the power. Display [Computer] [PMHOME] [INFO] [WIFI_INF.TXT] on your computer, then confirm your ID and password. WARNING To reduce the risk of fire or electric shock, 1) do not expose the unit to rain or moisture. 2) do not place objects filled with liquids, such as vases, on the apparatus. Do not expose the batteries to excessive heat such as sunshine, fire or the like. CAUTION For HDR-AZ1 Battery pack If the battery pack is mishandled, the battery pack can burst, cause a fire or even chemical burns. Observe the following cautions. •Do not disassemble. •Do not crush and do not expose the battery pack to any shock or force such as hammering, dropping or stepping on it. •Do not short circuit and do not allow metal objects to come into contact with the battery terminals. •Do not expose to high temperature above 60°C (140°F) such as in direct sunlight or in a car parked in the sun. •Do not incinerate or dispose of in fire. •Do not handle damaged or leaking lithium ion batteries. •Be sure to charge the battery pack using a genuine Sony battery charger or a device that can charge the battery pack. •Keep the battery pack out of the reach of small children. •Keep the battery pack dry. •Replace only with the same or equivalent type recommended by Sony. •Dispose of used battery packs promptly as described in the instructions. For RM-LVR2V Observer the following cautions, as there may be a risk of heat generation, fire or explosion. *Lithium-ion battery is built into the product. •Charge the product by the designated charging method. •Do not place the product in or near fire, or put the product in a microwave. •Do not leave the product in a car in hot weather. •Do not store or use the product in a hot and humid place such as in a sauna bath. •Do not disassemble, crush or pierce the product. •Do not expose the product to excessive shock such as dropping from a high place. •Do not expose the product to high temperatures above 60 °C (140 °F). •Keep the product dry. Dispose of the product appropriately. Charge the product by the designated charging method in the instruction manual. AC Adaptor Use the nearby wall outlet (wall socket) when using the AC Adaptor. Disconnect the AC Adaptor from the wall outlet (wall socket) immediately if any malfunction occurs while using the apparatus. Battery charger Even when the CHARGE lamp of this battery charger is off, the power is not disconnected. If any trouble occurs while this unit is in use, unplug it from the wall outlet (wall socket) to disconnect the power. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –– Reorient or relocate the receiving antenna. –– Increase the separation between the equipment and receiver. –– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –– Consult the dealer or an experienced radio/TV technician for help. The supplied interface cable must be used with the equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules. For Customers in Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. For Customers in Europe Notice for the customers in the countries applying EU Directives Manufacturer: Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan For EU product compliance: Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany Hereby, Sony Corporation, declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For details, please access the following URL: http://www.compliance.sony.de/ Notice If static electricity or electromagnetism causes data transfer to discontinue midway (fail), restart the application or disconnect and connect the communication cable (USB, etc.) again. This product has been tested and found compliant with the limits set out in the EMC regulation for using connection cables shorter than 3 meters (9.8 feet). The electromagnetic fields at the specific frequencies may influence the picture and sound of this unit. Disposal of waste batteries and electrical and electronic equipment (applicable in the European Union and other European countries with separate collection systems) This symbol on the product, the battery or on the packaging indicates that the product and the battery shall not be treated as household waste. On certain batteries this symbol might be used in combination with a chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are added if the battery contains more than 0.0005% mercury or 0.004% lead. By ensuring these products and batteries are disposed of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery and the electrical and electronic equipment will be treated properly, hand over these products at end-of-life to the applicable collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the applicable collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product or battery. For Customers in Singapore Even if your camera is turned off, AC power source (mains) is still supplied to it while connected to the wall outlet (wall socket) via the AC Adaptor. For customers in the U.S.A. and CANADA RECYCLING LITHIUM-ION BATTERIES Lithium-Ion batteries are recyclable. You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you. For more information regarding recycling of rechargeable batteries, call toll free 1-800-822- 8837, or visit http://www.call2recycle.org/ Caution: Do not handle damaged or leaking Lithium-Ion batteries. Battery pack This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 B/NMB-3 B This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption ratio (SAR). For Customers in the USA If you have any questions about this product, you may call: Sony Customer Information Center 1-800-222-SONY (7669) The number below is for the FCC related matters only. Regulatory Information Declaration of Conformity Trade Name: SONY Model No.: HDR-AZ1 Responsible Party: Sony Electronics Inc. Address: 16530 Via Esprillo, San Diego, CA 92127 U.S.A. Telephone No.: 858-942-2230 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Declaration of Conformity Trade Name: SONY Model No.: RM-LVR2V Responsible Party: Sony Electronics Inc. Address: 16530 Via Esprillo, San Diego, CA 92127 U.S.A. Telephone No.: 858-942-2230 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. Note on using [Camera and Live-View Remote] Wi-Fi function •Use the camera and the remote control in accordance with the regulations of the area of use. •You cannot use the Wi-Fi function of the camera and the remote control underwater. Security in the use of wireless LAN devices •To avoid hacking, access by malicious third parties, and other vulnerabilities, confirm that the wireless LAN is always secure. •It is very important to set up security on a wireless LAN. •If a problem occurs due to inadequate security measures or due to foreseeable circumstances, Sony Corporation is not responsible for any resulting damage. Notes before using the remote control under/near water •Make sure that no foreign matter such as sand, hair, or dirt gets inside the Multi terminal cover. Even a small amount of foreign matter may lead to water entering the remote control. •Confirm that the sealing gasket and its mating surfaces have not become scratched. Even a small scratch may lead to water entering the remote control. If the sealing gasket or its mating surfaces become scratched, consult your Sony dealer or local authorized Sony service facility. •If dirt or sand gets on the sealing gasket or its mating surfaces, wipe the area clean with a soft cloth that does not leave behind any fibers. •Do not open/close the terminal cover with wet or sandy hands or near water. There is a risk of sand or water getting inside. Before opening the terminal cover, perform the procedure described in “Cleaning after using the remote control under/near water". •Open the terminal card cover when the remote control is completely dry. •Always check that the terminal cover is securely locked. Notes on using the remote control under/near water •Do not subject the remote control to shock such as by jumping into water. •Do not open and close the terminal cover while under/near water. •The remote control sinks in water. Use the belt supplied with the remote control to prevent it from sinking. On GPS •The GPS antenna is built in not the camera but the front of the remote control. •As the positions of GPS satellites vary constantly, it may take longer to determine the location or the receiver may not be able to determine the location at all, depending on the location and time you use the camera. •GPS is a system that determines your position by receiving signals from satellites. Avoid using the GPS feature on your remote control in places where radio signals are blocked or reflected, such as a shadowy place surrounded by buildings or trees, etc. Use the remote control in open sky environments. •You may not be able to record location information at locations or in situations where radio signals from the GPS satellites do not reach the remote control as follows. –– In tunnels, indoors or under the shade of buildings. –– Between tall buildings or at narrow streets surrounded by buildings. –– In underground locations, locations surrounded by dense trees, under an elevated bridge, or in locations where magnetic fields are generated, such as near high voltage cables. –– Near devices that generate radio signals of the same frequency band as the remote control: near 1.5 GHz band mobile telephones, etc. •A GPS antenna is built in the front of the remote control. Placing the remote control upside down may cause positioning to take long time or may not be able to determine your position. •If you take images with the GPS of the remote control set to [ON], and upload those images to the Internet, the shooting location may be available to third parties. To prevent this, set the GPS of the remote control to [OFF] before shooting. On triangulation errors •If you move to another location right after turning the remote control on, it may take a longer time for the camera to start triangulating, compared to when you stay in the same place. •GPS satellite error When the remote control receives signals from more than three GPS satellites, it determines your present position. The triangulating error allowed by the GPS satellites is about 10 m (33 feet). Depending on the environment of the location, the triangulating error can be greater. In this case, your actual location may not match the location on the map based on the GPS information. Meanwhile, the GPS satellites are controlled by the United States Department of Defense, and the degree of accuracy may be changed intentionally. •Error during the triangulating process The remote control acquires location information periodically during triangulating. There is a slight time lag between when the location information is acquired and when the location information is recorded on an image, therefore, the actual recording location may not match the exact location on the map based on the GPS information. On GPS use restriction •Use GPS in accordance with the situation and regulations of the countries/regions where you use the remote control. Disposal Remove the battery pack before disposing of the remote control. Remove the battery pack The built-in battery pack is recyclable. When disposing of the remote control, remove the built-in battery pack and take it to your dealer. Notes When removing the battery pack, be careful of the following. •Remove the screws, etc. away from small children to prevent accidental swallowing. •Be careful not to injure your nails or fingers. Important information Do not remove the screws except when disposing of the remote control. We will refuse repairs or replacement if we judge there to have been unwarranted disassembly. 1 2 3 4 5 Press the ON/OFF button to turn off the power of the remote control. Disconnect the connected cables. Remove the screws with a Phillips-head screwdriver. (4 screws) Detach the cover. Push the hook outwards and remove the battery pack. Note on wireless network function We assume no responsibility whatsoever for any damage caused by unauthorized access to, or unauthorized use of, destinations loaded on the camera, resulting from loss or theft. [Camera] Operating temperature The camera is designed for use in temperatures between -5 °C and +40 °C (23 °F and 104 °F). Using in extremely cold or hot places outside this range is not recommended. Notes on long-time recording •Camera body and battery may get warm with use - this is normal. •Avoid using the camera for a long time when holding the camera in your hand or when it is directly touching your skin. It is recommended that you use the supplied adhesive mounts or waterproof case, or optional mount accessories. •Under high ambient temperatures, the temperature of the camera rises quickly. •Leave the camera alone for 10 minutes or longer to allow the temperature inside the camera to decrease to a safe level. •When the temperature of the camera rises, the image quality may deteriorate. It is recommended that you wait until the temperature of the camera drops before continuing to shoot images. On the overheat protection Depending on the camera and battery temperature, you may be unable to record movies or the power may turn off automatically to protect the camera. A message will be displayed on the screen of the remote control before the power turns off or you can no longer record movies. In this case, leave the power off and wait until the camera and battery temperature goes down. If you turn on the power without letting the camera and battery cool enough, the power may turn off again or you may be unable to record movies. About dust-proof and waterproof performance •The camera is dust-proof and waterproof (Depth of water 5 m (16 feet), 30 minutes continuously). For the notes on use of the waterproof case, refer to the instruction manual on the website. Note on optional accessories Genuine Sony accessories may not be available in some countries/ regions. [Live-View Remote] Operating temperature The remote control is designed for use in temperatures between -10 °C and +40 °C (14 °F and 104 °F). Using in extremely cold or hot places outside this range is not recommended. Specifications Camera Signal format: HDTV Power requirements: Rechargeable battery pack: 3.7 V (NP-BY1) Multi/Micro USB terminal: 5.0 V USB charging: DC 5.0 V, 500 mA Rechargeable battery pack NP-BY1: Maximum charge voltage: DC 4.2 V Maximum charge current: 975 mA Splashproof performance: Equivalent to IPX4 (based on standard testing by Sony) Operating temperature: -5 °C to +40 °C (23 °F to 104 °F) Storage temperature: -20 °C to +60 °C (-4 °F to +140 °F) Dimensions (Approx.): 24.2 mm × 36.0 mm × 74.0 mm (31/32 in. × 1 7/16 in. × 3 in.) (W/H/D, excluding protrusions and excluding the supplied waterproof case) Mass: Approx. 48 g (1.7 oz) (main body only) Total weight in use: Approx. 63 g (2.2 oz) (including the battery pack, excluding the supplied waterproof case) On trademarks •Memory Stick and are trademarks or registered trademarks of Sony Corporation. •Mac is a registered trademark of Apple Inc. in the United States and other countries. •iOS is a registered trademark or trademark of Cisco Systems, Inc. •Android and Google Play are trademarks of Google Inc. •iPhone is a trademark or a registered trademark of Apple Inc. •Wi-Fi, the Wi-Fi logo, Wi-Fi PROTECTED SET-UP are registered trademarks of the Wi-Fi Alliance. •The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries. •Adobe, the Adobe logo, and Adobe Acrobat are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. •microSDXC logo is a trademark of SD-3C, LLC. In addition, system and product names used in this manual are, in general, trademarks or registered trademarks of their respective developers or manufacturers. However, the ™ or marks may not be described in this manual.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project