AVLINK ADD-01IW Audio Delay Box Owner Manual

HDMI AUDIO DELAY

Conversion Box

ADD-01IW

U

SER

M

ANUAL

V1.0

ADD-01IW

Package Contents-

ƒ 1 ADD-01IW Unit

ƒ 1 User manual

ƒ 1 Power adapter DC 12V

ƒ 2

ƒ 4 foot pads

ƒ 1 HDMI cable 1.2M

Any thing missed, please contact with your vendor.

Introduction

The ADD-01IW connects to the HDMI signal from your source equipment (DVD player, satellite, cable… etc.) to your HDMI receiver equipment.

With the simple interface of ADD-01IW, the audio delay time can be adjusted so that sound and picture are perfectly synchronized. Up to 2700ms (2.7 second) error can be corrected. The HDMI audio signal is reproduced bit-perfect so no loss of audio quality is incurred.

Also the ADD-01IW can convert the HDMI audio sound to analog or digital.

Features

ƒ Max Audio Delay time 2.7 seconds.

ƒ Audio delay adjustment scale is 10ms.

ƒ Supports 2-channel PCM analog audio.

ƒ Supports Coaxial digital audio

ƒ Supports compressed audio format signal.(only HMDI and COAXIAL OUT)

Specifications

Input connector 1 x HDMI

TOP VIEW

e f c d g

1 x HDMI

Output Connector

Max Video support

Audio Input support sample rate

Audio output support sample rate

2 x RCA(for Analog)

1 x RCA(for Coaxial)

WUXGA or 1080P@60Hz

32K / 44.1K/ 48K

/ 96K / 192KHz

32K / 44.1K/ 48K

/ 96K / 192KHz

1. Select HDMI to Analog OUT channel

2. Display current audio delay time

3. - : decrease time delay value

4. + : increase time delay value

5. CHG: change time unit to adjust the audio delay time.

(second/ 100ms / 10ms)

Power Adapter (Min.) DC 12V with lock

Housing Metal

Weight 322g

Dimensions (LxWxH) 150x86x25mm

-1- -2-

FRONT VIEW

c

1. HDMI Input

2. RS232 port

3. Input Power Jack

REAR VIEW

d e

Operation

Setting the audio delay time

1. Select the time unit to adjust by pressing the button

“CHG”.

2. Then the selected time unit LED will keep flash. The user can change to the next time unit by pressing “CHG”.

Second => 100ms => 10ms => Second…

Adjust “second”

1. Pressing button “CHG” to select time unit “second” to change.

“Second” LED flash.

2. Pressing button “-” once to decrease 1 to 0.

3. Pressing button “CHG” to select time unit “100ms” to change. c d e

1. Coaxial output port

2. Analog output port

3. HDMI output port

Installation

1. Connect input equipment source to ADD-01IW.

2. Connect ADD-01IW to output device. (e.g. speaker).

3. Connect the power cord and turn on the ADD-01IW.

4. Turn on the source device.

-3-

Adjust “100 ms”

Adjust “10 ms”

3. Pressing the “+” or “-“ to increase /decrease the value

Old delay value 1.20 sec

Time unit to change: 100ms

“+” increase value from 2 to 3

4. Pressing button “+” three times to increase 2 to 5.

5. Stop operation and wait the LED stop flashing, then the new audio delay time “0.50” second take effect.

DIP Switch Settings

Select audio output channel from HDMI -input to “Analog” audio output.

“-” decrease value from 2 to 1

5. Stop operation and wait several second the LED stop flashing, then the new audio delay time will take effect.

6. “+” and “-“ can reset LED at the same time

Example:

Audio delay “1.20” second change to “0.50” second

Old audio delay time “1.20” second

-4-

1,2

ON ,OFF 5-6 CH

ON ,ON 7-8 CH

© C&C TECHNIC TAIWAN CO., LTD. All rights reserved.

Trademarks:

All the companies, brand names, and product names referred to this manual are the trademarks or registered trademarks belonging to their respective companies.

-5-