Esko 16 Automation Engine User Guide
Reklama
Reklama
Automation Engine 16
Tasks and Workflow Controls
01 - 2017
Automation Engine ii
Contents
1. Add Dynamic Marks................................................................................................................................12
2. Add Ink Eaters..........................................................................................................................................14
3. Add Marks to Imposition.......................................................................................................................17
4. Add Margins..............................................................................................................................................18
5. Add SmartMarks......................................................................................................................................19
6. Add to Pages View...................................................................................................................................21
7. Add To Products.......................................................................................................................................22
8. Adjust PDF Screening..............................................................................................................................23
9. Apply ArtPro Action List........................................................................................................................ 25
10. Apply Creep............................................................................................................................................ 26
11. Apply PantoneLIVE Condition............................................................................................................. 27
12. Archive Job..............................................................................................................................................29
13. Assign PDF Pages to RunList...............................................................................................................30
14. Calculate Ink Key Settings (InkPlanner)........................................................................................... 31
15. Change Imposition Layout.................................................................................................................. 33
16. Check Dynamic VDP Database........................................................................................................... 34
17. Check Job Parameters.......................................................................................................................... 35
18. Check Print Rules (PRC)....................................................................................................................... 36
19. Check Product Parameters..................................................................................................................37
20. Check Technical Inks............................................................................................................................ 38
21. Compare PDF..........................................................................................................................................39
22. Convert CMYK Colors............................................................................................................................40
23. Convert Colors with Equinox.............................................................................................................. 41
24. Convert IMP file to Normalized PDF................................................................................................. 44
25. Convert Selection.................................................................................................................................. 45
26. Contourize & Clean............................................................................................................................... 46
Contents
27. Copy or Move File..................................................................................................................................47
28. Create CAD Sheet.................................................................................................................................. 48
28.1 Ticket settings .................................................................................................................................50
28.2 Positioning a One Up graphic onto a Station ..............................................................................53
28.3 Distributing the One Up graphics onto the Stations .................................................................. 54
28.4 Bleed and overlap ..........................................................................................................................55
28.5 Bleed Overlap Priority Decided by ArtiosCAD Artwork Panels ...................................................56
29. Create ArtiosCAD Report from XML.................................................................................................. 57
30. Create Design (DesignWizard).............................................................................................................58
30.1 Using SmartNames in a DesignWizard template ........................................................................ 59
31. Create IMP File.......................................................................................................................................61
32. Create Imposition from JDF Layout...................................................................................................62
33. Create Imposition from RunList.........................................................................................................63
34. Create Job task...................................................................................................................................... 64
35. Create or Modify WebCenter Project................................................................................................ 65
36. Create PAF / JPG / XML (LinkEdge)..................................................................................................... 66
36.1 Pack/UnPack ................................................................................................................................... 66
36.2 XML ..................................................................................................................................................67
36.3 JPEG ................................................................................................................................................. 68
37. Create PDF File from JDF RunList.......................................................................................................70
38. Create PDF File from RunList..............................................................................................................71
39. Create Merged Plate.............................................................................................................................72
40. Create Master DCS File.........................................................................................................................73
41. Create Report (ReportMaker)............................................................................................................. 74
41.1 Creating a ReportMaker Template ............................................................................................... 75
41.2 Adding Previews of Details in a Report PDF ................................................................................79
41.3 Adding a 3D Object to a Report PDF ........................................................................................... 80
42. Create RunList........................................................................................................................................82
43. Create RunList from PDF..................................................................................................................... 83
44. Create Sheet Report from IMP File....................................................................................................84
45. Create Tiles.............................................................................................................................................85
46. Create Wrapper File..............................................................................................................................86
46.1 Page Size tab .................................................................................................................................. 86
iii
iv
Automation Engine
46.2 Inks tab ........................................................................................................................................... 87
46.3 Separations tab .............................................................................................................................. 88
47. Create XML File......................................................................................................................................89
48. Crop LEN file...........................................................................................................................................90
49. Data Collector........................................................................................................................................ 91
50. Data Splitter........................................................................................................................................... 92
51. Delete File............................................................................................................................................... 93
52. Download WebCenter Document.......................................................................................................94
53. Enrich Black............................................................................................................................................95
53.1 General Tab .....................................................................................................................................95
53.2 Scan Tab ..........................................................................................................................................96
54. Expand Dynamic VDP Data................................................................................................................. 98
55. Export ArtiosCAD Design Info...........................................................................................................100
56. Export ArtPro to Normalized PDF File............................................................................................ 101
57. Export IMP File to GRI File................................................................................................................ 103
58. Export IMP File to JDF Layout...........................................................................................................104
59. Export IMP File to JDF Post-Press.....................................................................................................105
60. Export IMP File to PDF File................................................................................................................106
61. Export IMP File to PDF File Chain.................................................................................................... 107
62. Export IMP File to PostScript File.................................................................................................... 108
63. Export Imposition to JDF Layout......................................................................................................109
64. Export Imposition to PDF File...........................................................................................................110
65. Export Nested Layouts.......................................................................................................................111
66. Export Step and Repeat to JDF Layout........................................................................................... 112
67. Export to 3D......................................................................................................................................... 113
67.1 Export to 3D Settings .................................................................................................................. 114
68. Export to ArtPro File...........................................................................................................................116
69. Export to EPS/DCS File........................................................................................................................117
69.1 Output ........................................................................................................................................... 117
70. Export to Normalized PDF File......................................................................................................... 119
Contents
71. Export to Normalized PDF File (Embed All)....................................................................................121
72. Export to PDF File............................................................................................................................... 122
72.1 Output ........................................................................................................................................... 123
72.1.1 Password Security ..............................................................................................................124
72.2 Device ............................................................................................................................................ 126
72.3 Color Management ...................................................................................................................... 126
72.4 Compression .................................................................................................................................128
72.5 Advanced .......................................................................................................................................129
73. Export to PostScript File.................................................................................................................... 131
73.1 Output ........................................................................................................................................... 131
73.2 Device ............................................................................................................................................ 132
73.3 Color Management ...................................................................................................................... 133
73.4 Inks / Separations .........................................................................................................................134
73.5 Rasterize ........................................................................................................................................135
73.6 Compression .................................................................................................................................136
73.7 Advanced .......................................................................................................................................136
74. Extract Inks...........................................................................................................................................139
75. Fork........................................................................................................................................................ 141
76. Image to Screened Separations........................................................................................................142
77. Image to Unscreened Separations...................................................................................................143
78. Import Image....................................................................................................................................... 144
79. Import JDF Layout...............................................................................................................................146
80. Import JDF Step & Repeat................................................................................................................. 147
81. Import JDF Stripping...........................................................................................................................149
82. Import Substrate Sizes from XML....................................................................................................150
83. Inspect Artwork...................................................................................................................................151
84. Inspect Barcodes................................................................................................................................. 152
85. Inspect Braille...................................................................................................................................... 153
86. Inspect Spelling....................................................................................................................................154
87. Inspect Text.......................................................................................................................................... 155
88. Integrate via External Hot Folder.................................................................................................... 156
89. Integrate with WebCenter.................................................................................................................158
90. Interact with Database...................................................................................................................... 159 v
vi
Automation Engine
91. Interact with SAP................................................................................................................................ 160
92. Interact with Web Service................................................................................................................. 161
93. Join..........................................................................................................................................................162
94. Join XML Files.......................................................................................................................................163
95. Link Product To Job.............................................................................................................................164
96. Load Structural File............................................................................................................................ 165
97. Manage Color....................................................................................................................................... 167
97.1 Converting to another CMYK Profile .......................................................................................... 167
97.2 Reseparating your CMYK File ......................................................................................................172
97.3 Converting and Reseparating your File ......................................................................................176
98. Manage Milestone...............................................................................................................................177
99. Manage Product Status......................................................................................................................178
100. Map Data............................................................................................................................................ 179
101. Mark as Proof.................................................................................................................................... 180
102. Mark File (link)...................................................................................................................................181
103. Merge PDF Files................................................................................................................................. 182
104. Modify Workflow Parameter Values............................................................................................. 183
105. Normalize PDF File............................................................................................................................184
105.1 Colors .......................................................................................................................................... 184
105.2 Separations .................................................................................................................................185
106. Normalize PostScript / PDF / Illustrator 8.0 File..........................................................................186
106.1 Pages ........................................................................................................................................... 186
106.2 Color Management .................................................................................................................... 187
106.2.1 Destination Color Space ..................................................................................................187
106.2.2 Spot Colors .......................................................................................................................188
106.2.3 RGB ................................................................................................................................... 188
106.2.4 CMYK and Gray ................................................................................................................189
106.3 Inks .............................................................................................................................................. 189
106.4 Overprint .....................................................................................................................................190
106.5 Images .........................................................................................................................................192
106.6 Page Size .....................................................................................................................................193
106.7 Other ........................................................................................................................................... 194
106.8 Output .........................................................................................................................................196
107. Normalize TIFF/IT File.......................................................................................................................197
Contents
108. Optimize and Clean (PSFix)............................................................................................................. 198
108.1 General ........................................................................................................................................198
108.2 Borders ........................................................................................................................................200
109. Optimize PDF Document..................................................................................................................202
109.1 Document ................................................................................................................................... 202
109.1.1 Adjust Page Box ...............................................................................................................203
109.1.2 Outline Page Box ............................................................................................................. 204
109.2 Layers .......................................................................................................................................... 205
109.3 Images .........................................................................................................................................205
110. Optimize PDF Separations...............................................................................................................207
110.1 Colors .......................................................................................................................................... 207
110.2 Inks .............................................................................................................................................. 208
110.3 Ink Properties ............................................................................................................................. 210
110.4 Overprints ................................................................................................................................... 211
111. Outline Fonts..................................................................................................................................... 213
112. Preflight with PitStop.......................................................................................................................214
113. Prepare for Inspection..................................................................................................................... 215
113.1 Settings ........................................................................................................................................216
114. Prepare for Viewer............................................................................................................................219
115. Prepare Graphics for Nesting......................................................................................................... 220
116. Prepare Station..................................................................................................................................221
117. Print..................................................................................................................................................... 224
118. Print IMP File..................................................................................................................................... 225
119. Print on Digital Press....................................................................................................................... 226
119.1 Supported File Types ................................................................................................................. 226
119.2 Using the Print on Digital Press Ticket in a Workflow .............................................................227
119.3 Print on Digital Press Task Settings ..........................................................................................227
119.3.1 General Tab ...................................................................................................................... 228
119.3.2 Files tab ............................................................................................................................ 229
119.3.3 Step and Repeat Tab ....................................................................................................... 231
119.3.4 Transformation Tab ......................................................................................................... 238
119.3.5 Color Management Tab ...................................................................................................238
120. Process PDF Spreads.........................................................................................................................240
121. Proof (FlexProof)................................................................................................................................243
121.1 General ........................................................................................................................................243
121.2 Inks .............................................................................................................................................. 243
vii
Automation Engine
121.3 Advanced .................................................................................................................................... 244
121.4 Pre-RIP .........................................................................................................................................244
121.5 Output .........................................................................................................................................245
121.5.1 Example: Color Managing White Ink for an Epson WT7900 Proof ...............................246
121.6 Color ............................................................................................................................................248
121.6.1 For Normal Proof .............................................................................................................248
121.6.2 For Emulation Proof ........................................................................................................ 250
121.7 Verification .................................................................................................................................. 251
122. Proof for Contract Approval............................................................................................................253
123. Proof for Content Approval.............................................................................................................254
124. Proof IMP File (FlexProof)................................................................................................................ 255
125. Proof to File - Unscreened...............................................................................................................256
126. Publish Imposition on WebCenter Chain......................................................................................257
127. Publish On WebCenter..................................................................................................................... 258
128. Relocate Job........................................................................................................................................259
129. Remove Job.........................................................................................................................................260
130. Remove Product................................................................................................................................ 261
131. Resize PDF for Output......................................................................................................................262
131.1 Resizing to a Specific Page Size ................................................................................................262
131.2 Not Resizing to a Specific Page Size .........................................................................................263
132. Resolve OPI.........................................................................................................................................265
133. Restore Job......................................................................................................................................... 266
134. RIP IMP File to Screened and Unscreened Tiff File.....................................................................267
135. RIP to CDI LEN File............................................................................................................................268
135.1 Output .........................................................................................................................................268
136. RIP to Screened and Unscreened DCS File................................................................................... 270
136.1 Output .........................................................................................................................................270
136.2 Inks .............................................................................................................................................. 271
137. RIP to Screened and Unscreened PDF File................................................................................... 273
137.1 Output .........................................................................................................................................273
138. RIP to Screened and Unscreened PostScript File........................................................................ 276
138.1 Output .........................................................................................................................................276
139. RIP to Screened and Unscreened Tiff File.................................................................................... 278
139.1 General ........................................................................................................................................278
viii
Contents
139.2 Inks .............................................................................................................................................. 279
139.3 Advanced .................................................................................................................................... 280
139.4 Merge Queue ..............................................................................................................................281
139.5 Pre-RIP .........................................................................................................................................282
139.6 Output .........................................................................................................................................283
140. Router..................................................................................................................................................285
141. Run ArtiosCAD Standard..................................................................................................................286
142. Run Script........................................................................................................................................... 287
143. Select File............................................................................................................................................288
144. Select Mark File................................................................................................................................. 289
145. Select Job............................................................................................................................................ 290
146. Select Product....................................................................................................................................291
147. Select Referenced File...................................................................................................................... 292
148. Send E-mail......................................................................................................................................... 293
149. Send PostScript File to Device........................................................................................................ 295
150. Send To Nexus................................................................................................................................... 296
151. Set Priority..........................................................................................................................................297
152. Sort.......................................................................................................................................................298
153. Split Pages.......................................................................................................................................... 299
154. Split XML............................................................................................................................................. 301
155. Step & Repeat CAD based................................................................................................................302
155.1 General ........................................................................................................................................302
155.2 Plate Setup ................................................................................................................................. 303
155.3 CAD Options ............................................................................................................................... 304
156. Step & Repeat Tabular..................................................................................................................... 306
156.1 General ........................................................................................................................................306
156.2 Grids ............................................................................................................................................ 309
156.2.1 Grid Settings .....................................................................................................................310
156.3 Rules ............................................................................................................................................315
156.4 Formulas ..................................................................................................................................... 315
156.5 Using Database Queries: an Example ......................................................................................318
157. Step & Repeat Tabular (Dynamic)..................................................................................................321
157.1 Assignment of Input Files ..........................................................................................................321
157.2 Splitting Output, Blocks and Gaps ........................................................................................... 322
ix
x
Automation Engine
157.3 Sheet and Plate Options ........................................................................................................... 324
157.4 Filling Order ................................................................................................................................325
157.5 Adding Marks ............................................................................................................................. 327
157.6 Setting specific Grid Options .................................................................................................... 327
157.7 Specification of RunList XML in Dynamic Step & Repeat ........................................................328
158. Step & Repeat Template based...................................................................................................... 331
159. Step & Repeat Template based (Dynamic)...................................................................................334
160. Submit to CDI.....................................................................................................................................335
161. Submit to Gang Run......................................................................................................................... 336
162. Submit to Kongsberg Table............................................................................................................. 337
163. Submit to Plate Merger................................................................................................................... 338
164. Submit XML to Gang Run................................................................................................................ 339
165. Synchronize ArtiosCAD Boards.......................................................................................................340
166. Synchronize ArtiosCAD Companies............................................................................................... 341
167. Track Edit Session............................................................................................................................. 342
167.1 Viewing the Edit Session Information in the Pilot ...................................................................342
167.2 Storing the Editing Information System-Wide ......................................................................... 343
167.3 Which Edit Actions are Logged?
............................................................................................... 344
168. Trap with PowerTrapper.................................................................................................................. 346
168.1 What is Trapping?
...................................................................................................................... 346
168.2 Distance & Direction ..................................................................................................................347
168.3 Color & Shape ............................................................................................................................ 349
168.4 Processing ...................................................................................................................................351
168.5 Rules ............................................................................................................................................352
168.6 Output .........................................................................................................................................353
169. Unzip.................................................................................................................................................... 354
170. Upload via FTP................................................................................................................................... 355
171. Upload via SFTP................................................................................................................................. 356
172. Upload To Cloud Storage................................................................................................................. 357
173. Verify Certification............................................................................................................................358
174. Version PDF........................................................................................................................................ 359
175. Wait...................................................................................................................................................... 362
176. Wait for Action (Checkpoint).......................................................................................................... 363
Contents
177. Wait for Files......................................................................................................................................364
178. Wait for Files (via JDF)......................................................................................................................365
179. Wait for Product Status................................................................................................................... 366
180. Zip.........................................................................................................................................................367
181. Outdated and Soon Outdated Tasks............................................................................................. 368
181.1 Concept of (Soon) Outdated Tasks ...........................................................................................368
181.2 Expand Variable Data to PPML File (Soon Outdated) ............................................................. 370
181.2.1 Expand Variable Data to PPML File (Soon Outdated) - old documentation page ....... 370
181.3 Expand Variable Data to PPML File (DeskPack Only) (Soon Outdated) ..................................370
181.3.1 Expand Variable Data to PPML File (DeskPack only) (Soon Outdated) - old documentation page ................................................................................................................371
181.4 Preflight via External Application (Soon Outdated) .................................................................371
181.4.1 Preflight via External Application (Soon Outdated) - old documentation page ...........371
181.5 Print on Digital Press (PPML) (Soon Outdated) ....................................................................... 371
181.5.1 Print on Digital Press (PPML) (Soon Outdated) - old documentation page ................. 372
181.6 Process Remote Proofs (Soon Outdated) ................................................................................ 372
181.6.1 Process Remote Proofs (Soon Outdated) - old documentation page ..........................372
181.7 Rip to WS4000 Series (Soon Outdated) ................................................................................... 373
181.7.1 Rip to WS4000 Series (Soon Outdated) - old documentation page ............................. 373
181.8 Send to Odystar (soon outdated) .............................................................................................373
181.8.1 Send to Odystar (soon outdated) - old documentation page ...................................... 374
181.9 Tasks that became outdated in this version ........................................................................... 374
xi
1
Automation Engine
1. Add Dynamic Marks
Concept
Use this task to apply marks from a pre-defined Set of Dynamic Marks to the input PDF file.
These type of marks are created using the
Dynamic Marks plug-in for Adobe Illustrator
.
This task produces a native PDF. This PDF does contain all the information from the input file
(for example object based screening).
Note: In workflows where you need a normalized PDF in the steps after this Add Dynamic
Marks task, you can add the Normalize PostScript / PDF / Illustrator file task to the workflow. If you use this extra task, then make sure that the option '
Use rulings, angles and
dot gain compensation from file' is selected (in the Inks tab) to preserve the screening parameters.
Task Settings
12
Replace existing marks: Select this to remove existing marks from the input file while adding the new mark set.
Mark Set: In this table, you define which mark set you Add To which pages. Learn more
.
Processing: This choice affects how long the task needs to process:
•
Calculate once and copy (faster): When selected, the marks are calculated only once for the first and second page. After that, this information is copied to all other pages. The content from the first page is copied to the odd pages, the content from the second page is copied to all even pages. This method is also called "caching".
Note: Some marks cannot be cached because the content depends on the page number
(for example a text mark with a variable for sheet number). To avoid a wrong output, the task will fail in this case (a message will be displayed in the task's details)
Note: Also beware of using this option when adding text marks that contain the current time. If you do so, the time stamp from the first page will be copied to all odd pages and the time stamp from the second page will be copied to all even pages.
• Calculate for each page (more accurate): Select this when the calculation of the marks needs to happen for each page separately. This task will take longer to process, but the results will be more accurate.
Automation Engine
1
Adding Mark Sets
• Click Add and specify the Mark Set. Select it from the list, or type its name or use
SmartNames.
In ' Add To': Specify on what page(s) the mark set should be applied: All, Even , Odd, First or
Last page.
• Use the buttons Remove and Edit to further manage this table.
13
2
Automation Engine
2. Add Ink Eaters
Ink Eaters help to achieve a constant ink consumption over the width of the plate. This makes it easier for press operators to set the ink keys, and results in a faster setup time for the press.
Ink Eaters are typically added to non-printed areas outside the printing job. These areas can be left-overs that will be cut off or the white spaces next to or even in between the one-ups.
Ink Eaters help to avoid excess ink build-up by stabilizing "peaks" and "lows" in the ink key
histogram. This prevents spilling of excess ink onto the printed zones of the actual printing job. You can flatten the ink key histogram by filling non-printed zones with a gradient. A gradient helps to avoid hard edges in the compensation object. You can specify a minimum ink density and a minimum ink key value. You can request warnings when the maximum Total
Area Coverage (TAC) is too high. These areas are then compensated (filled with ink) depending on the strategy settings.
The task settings allow you to determine where the ink eater areas should be and with what they should be filled:
Ink Eaters tab
14
Automation Engine
2
•
Ink Eaters Areas
• Fill Named Objects: Type in the name of the Named Object as you defined it in Esko
Plato for example.
• Create Ink Eater Areas: Specify the start and end of the areas:
•
Start from Station's
• Die Shape: Select this to start from a die shape (for example pre-defined in Plato).
• Trim Box or Media Box: Select this to start from the Trim or Media Box of the oneup on the plate. Media Box is larger and it contains the Trim Box.
• Die Annotation: Select this to start from the object that was marked as a die (for example in Plato).
• End at: Specify what should be used as the end of the area.
• Keep Away field: Fill in a distance to set an offset for the Ink Eater object in relation to the die shape or Trim Box.
• Select Exclude SmartMarks if you want to exclude SmartMarks from the Ink Eater object.
• Scan Ink Coverage:
When you selected a contour object or a group of objects for ink coverage, select one of these options:
• Scan: Specify what area needs to be scanned:
15
2
Automation Engine
• All Inside Sheet (Sheet View): To scan within the sheet and exclude objects outside the sheet.
• All Inside Plate (Sheet View): To scan all objects on the sheet and plate. Objects that extend the plate area or are outside the plate are not included.
• Direction: This is the scanning direction. Horizontal means that the ink zones are vertical on the plate and the ink histogram is on the horizontal base of the document.
The direction of the compensation gradient in the ink eater area is horizontal.
• Resolution: This defines the number of intermediate steps of the gradient to be used as compensation. Use Very Low for 5 steps, Low for 15 steps, Medium for 30 steps, High for 45 steps and Very High for 60 steps.
Note:
You can achieve global compensation by defining a low resolution value (for example 5 gradient steps). This gives a very smooth compensation gradient along the length of the press. The ink histogram zones are then very wide.
You can achieve very local compensation by defining a high resolution value (for example 60 gradient steps). This results in a gradient with more banding.
•
Ink Density
•
Compensation
• Strategy and Range: This defines how the Ink Eater areas should be filled.
• Economic: This minimizes the use of ink.
• Intermediate: This optimizes ink use to result in a medium performance in print..
• Best performance: This maximizes the use of ink to give the best print performance.
• Minimum Ink Density: Select this option to define a minimum density.
• Minimum Ink key Value: Select this option to define a minimum ink key value for the ink eater area. The ink density of the gradient will be adjusted to make sure the ink key value is higher than this setting.
• Maximum Total Area Coverage: Select this option to define a maximum total area coverage (for example 270%). You will then get warnings when in those areas of the histogram where the total ink coverage exceeds this limit.
Inks tab
• Select Non-process, Opaque and/or Varnish inks if you want to Exclude them from being used in the ink eaters. .
• Select Keep similar inks in their original separations to keep the original separations in the output file.
16
Automation Engine
3
3. Add Marks to Imposition
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
17
4
Automation Engine
4. Add Margins
This task is documented in the chapter
CDI Platemaking Workflow
. Find a direct link
here
.
18
Automation Engine
5
5. Add SmartMarks
Add SmartMarks
This task applies a set of SmartMarks to a PDF file. A SmartMark set is a group of marks that can be created in PackEdge, Plato or i-cut Layout. Learn more about creating them in the user manuals of these editors.
Your input file may already have SmartMarks. You first need to decide what to do with those:
• Add to current set: This merges the new SmartMark set with any already present
SmartMark sets.
• Replace current set: This replaces any already present SmartMark sets.
Note:
• Since only a normalized PDF file can contain SmartMarks, Replace current set is not relevant for native PDF files.
• When applying a SmartMark set on a native PDF file, the task output file will also be a native
PDF. Any applied SmartMark set will be converted into normal PDF objects. Learn more about native and Normalized PDFs in
File Formats, Normalization and XMP
.
Load on all Pages: This loads the selected SmartMark set on all pages of a multi page input file.
Load different set on even pages: This loads a different SmartMark set on the even pages of a multi-page input file. For example on the backside of a layout. When selected, define the name of the extra set.
Load Mark Set in bottom Layer: This allows you to choose if the marks should be applied on top of the graphics or if the graphics should be on top of the marks.
19
5
Automation Engine
Fit Margins: Depending on the setup of your SmartMark set, marks can be (partially) positioned outside the PDF’s Media Box. Select this option to extend the Media Box to all visible content outside the Trim Box.
20
Automation Engine
6
6. Add to Pages View
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
21
7
7. Add To Products
This task is documented in the chapter
Products
. Find a direct link
here
.
Automation Engine
22
Automation Engine
8
8. Adjust PDF Screening
This task serves to apply rule-based modifications of screening parameters. One rule could be enough to accommodate various specific requirements, but if needed you can add an elaborate set of rules (see an example below).
You can preview the Separation Details when a file is selected. This will display the results for the specified set of rules in the current file.
Some example applications:
• You can also criteria like Ink Book, Printing Method or Ink Type. For example: when the printing method is flexo, set the Dot shape to "F".
• Or use SmartNames. For example: if the ink name is "Cyan", "Magenta", "Yellow" or
"Black", set Dot shape to [mydotshape] .
• A more elaborate example when using Object Based Screening: when the name is "Cyan" and angle is between "0" and "45", then set the angle to "30" and Dot shape to "R".
Note: In native PDF, the screening parameter 'DotShape' does not exist. Instead there is a ' SpotFunction Name', which can have a limited number of values like SimpleDot,
Ellipse, or Square which are mapped to the Esko dot shapes "C", "E", "S" respectively. Other
SpotFunctionName values are mapped to "C".
When reading Native PDF fIles, the task Normalize PostScript / PDF / Illustrator File does not take account of the DotShapes (SpotFunction Name) values. You need to adjust the PDF
Screening parameters during or after normalization.
1. Click Add to define a rule.
2. Enter a Name for the rule. For example the name of the ink that you here adjust.
3. Select 'Apply rule to all separations' when this is what you want.
4. Define a condition under 'If separation matches'. You can choose from Ink name, Ink
book, Ink type, Printing method, Ruling, Angle and Dot shape. Set the condition and enter a related text in the field. Click to pick a separation name from those found in the input file. If needed, add more criteria by clicking on ' +'.
23
8
Automation Engine
Note: Setting up these rules is very similar to creating filters in Views. Learn more in
Using
Filters and Creating Smart Views
.
5. Define what you want to adjust in 'Apply separation settings'. You can specify Ruling,
Angle and/or Dot shape.
6. Click OK.
7. Repeat steps 1-6 to add more rules.
24
Rules are applied from top to bottom. When a separation was already handled by a rule, it will not be handled again by a lower set rule. In above example screenshot, the rule "<all separations>" will only be applied to all other separations that were not handled by any rule set above.
When an input file was selected, you can click Preview to see what the above rules will result in.
8. Click OK to save the ticket.
Automation Engine
9
9. Apply ArtPro Action List
This task is documented in the dedicated chapter
ArtPro automation using ArtPro Action Lists
.
Find a direct link
here
.
25
10
Automation Engine
10. Apply Creep
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
26
Automation Engine
11
11. Apply PantoneLIVE Condition
Concept
Important: This task requires you to be familiar with PantoneLIVE. PantoneLIVE ink books are ink books that take into account on what substrate an ink will be printed on. These books are stored in the cloud. Learn more in the
user guide of the Color Engine Pilot
(chapter 'Inks').
This task replaces all Pantone inks in the file with inks from the selected PantoneLIVE
Dependent Standard Condition (that you already downloaded). Only the ink name and ink book changes. Other ink settings (ruling, angle, dot shape, ink type and printing method) are not changed.
Note: This kind of ink mapping is what users of PantoneLIVE do interactively in Esko PackEdge.
This task may be a more productive way.
See this figure showing several inks of the identity 120 :
Possible Mappings
This task can change
• any Pantone (or PantoneLIVE Master) ink to the corresponding ink in the selected target
' Dependent Standard'.
• any PantoneLIVE Dependent Standard ink to the corresponding ink in the (other) target dependent standard.
27
11
Automation Engine
Note: If the input file contains a PantoneLIVE dependent ink and a Pantone (or
PantoneLIVE master) ink with the same identity (for example P307C FSGB and PANTONE
307 C), and if the dependent standard of the ink in the file corresponds with the target dependent standard, then both inks will be merged (in our example they are merged to
P307C FSGB).
Attention: This task does not change:
• any non Pantone inks found in the input file
• any CMYK process inks found in the input file.
28
Automation Engine
12
12. Archive Job
This task is documented in the
separate chapter about Jobs
. Find a direct link
here
.
29
13
Automation Engine
13. Assign PDF Pages to RunList
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
30
Automation Engine
14
14. Calculate Ink Key Settings
(InkPlanner)
This task creates CIP3 files (mainly PPF) which contain all necessary data for the printing and further processing of a job.
Attention: This task is valid when you RIP'ed files using an Esko FlexRip. If you are using
Esko Imaging Engine
, use the task
Calculate Ink Key Settings (CIP3)
.
Note: This InkPlanner ticket cannot be launched separately. It always needs to be part of a 'task chain' preceded by an Expose to FlexRip ticket. It cannot be connected to Proof or
Approval tickets.
Select the Plate Setting File (*.ini), which contains specific information for the CIP3 generation, like image position, rotation, compensation, etc.
Select the Press Configuration File (*.dat), which contains data about the press and the
InkPlanner output.
Note: Both above mentioned file types are created using the CIPress Setup tool (installed with FlexRip).
The name entered in the Output File Name will be used for making files created by
InkPlanner. This InkPlanner output will be stored in the 'output directory' that was specified in the 'Press Configuration File' (*.dat).
Page Side: select Automatic, Front or Back.
Note: The option selected here has priority over the page side option selected in the 'Plate
Settings' file.
Tip: In case of an imposition file, select Automatic. This will process the page side settings typical of the imposition file.
CIP3
These fields enter administrative data in the output file. This information is used further processing CIP3 files.
• JobName: (required) If nothing is specified, the default job name will be used.
• SheetName: (optional)
• JobCode: (optional) is the code used for the job identification.
• Make: (optional) refers to the make of expose device.
• Artist: (optional) refers to the person who created the sheet.
• Customer: (optional) refers to the target customer.
• Software: (optional) refers to the software used to create the sheet.
31
14
Automation Engine
• Paper Weight: (optional) the weight of the paper to be used.
• Paper Thickness: (optional) the thickness of the paper to be used.
• Paper Grade: (optional) the grade of the paper to be used.
Note: If you do not enter anything in these CIP3 fields, the corresponding input fields in the
'CIP3' tab of the 'Plate Settings' tab in the 'CIPress Setup' tool will be checked.
32
Automation Engine
15
15. Change Imposition Layout
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
33
16
Automation Engine
16. Check Dynamic VDP Database
Concept
This task validates a VDP database before running the Expand Dynamic VDP Data task.
Although the same checks are done as in the Expand Dynamic VDP task, this Check Dynamic
VDP Database task faster because it does not generate any output.
This task analyzes all entries from the database using rules stored in Variable Data Template
(VDT file).
Note: When used in a workflow and the check succeeds, the task will produce a database
CSV file which can be used as input for the next workflow step. When the check fails, the task delivers a report file listing the detected issues.
This task requires
• a CSV file as input
• a VDT file as mandatory parameter.
Task Settings
• CSV File Encoding: Specify the wanted character encoding. The default encoding is UTF-8.
This is also the recommended encoding.
• Field Separator: Let the task Detect automatically or choose , (Comma), ; (Semicolon),
Space or Tab.
• Empty lines: Choose what needs to happen with empty lines in the input CSV file. Only lines ending with CR, LF or CR LF can be detected as an empty line (it is possible to mix different line endings in a single file). All empty lines at the end of the file are skipped.
• Field Names: Field names map data chunks from the database entry to its corresponding
VDP template items. Choose from:
• From CSV File: When selected, the task will extract Field Names from the first record of the CSV file by default.
Attention: Field Names can only contain the following characters: lower- or upper-case ASCII letters ("a-z, A-Z"), digits ("0-9") or underscore ("_").
• From Header File: When selected, define a Header File that contains the Field Names.
Such a file
• should contain a single line specifying the
Field Names
• should have a Field Name corresponding to each column in the CSV file.
• and the CSV file must use the same delimiter and encoding.
• Template: browse to the Variable Data Template file that contains the rules to check the database validity. Such a template is created and exported using the
Dynamic VDP
DeskPack Plug-in for Adobe Illustrator.
34
Automation Engine
17
17. Check Job Parameters
This task is documented in the chapter dedicated to
Jobs
. Find a direct link
here
.
35
18
Automation Engine
18. Check Print Rules (PRC)
This task is documented in the chapter
Quality Control tools
. See
Check Print Rules (PRC)
.
36
19. Check Product Parameters
This task is documented in the chapter
Products
. Find a direct link
here
.
Automation Engine
19
37
20
Automation Engine
20. Check Technical Inks
This task checks if the input file (Normalized PDF, PDF or Plato File) contains technical objects in knockout.
The task setting allow to define if the task will fail or end with a warning when it finds technical objects in knockout.
Learn more in the Esko white paper Working with Technical Inks as available under 'Related
Documentation' on
https://www.esko.com/en/Support/Product?id=Automation%20Engine
.
38
Automation Engine
21
21. Compare PDF
This task is documented in the chapter
Quality Control tools
. See
Compare PDF
.
39
22
Automation Engine
22. Convert CMYK Colors
This old technology is still supported but no longer commercially available.
Please find its documentation in the
manual of Automation Engine 14.1 or older
(as part of the
Reference Guide).
40
Automation Engine
23
23. Convert Colors with Equinox
This task serves to convert PDF files’ colors using
Equinox
.
Equinox is Esko's award winning expanded gamut printing solution. Expanded gamut printing is using a standardized set of 5, 6 or 7 inks for printing, instead of CMYK plus different spot colors for each print job.
Equinox functionality is available in Automation Engine,
ArtPro
,
PackEdge
, the
Color Engine Pilot
and as a plug-in for Adobe Photoshop.
Learn more in the
Equinox user manual
.
Use Cases
Use this task to convert your file's colors to prepare for expanded gamut printing, especially in these cases:
• You don't have ArtPro or PackEdge and you work with regular (native) PDF files.
With this task, you don't need to convert your file to an ArtPro file or a Normalized PDF file before conversion, but you can get the same results as if you did.
• You do have ArtPro or PackEdge, but you want to automate the conversion.
You can, for example:
1. Set up an Equinox color strategy in the Color Engine Pilot.
2. Use that color strategy to experiment with Equinox conversion in ArtPro or PackEdge, and make small adjustments to the conversion until it is exactly the way you want it.
3. Then use the adjusted color strategy in this Convert Colors with Equinox task to automate the conversion of all your file's variants or "SKUs" (Stock Keeping Units), for example for different languages, sizes, flavors...
This task takes both PDF and Normalized PDF files as input. When working with regular PDFs, it will automatically normalize them using the Normalize ticket that is selected in
the item
'Processing Preferences' in the Configure tool
.
This task keeps your file's metadata intact (for example CAD information).
Tip: We recommend you place this task towards the end of your workflow, as close to the output device as possible.
Parameters
1. Select the Color Strategy you want to use for the conversion. This must be an Equinox
Color Strategy that you have created in the Color Engine Pilot.
Typically, your color strategy doesn't only contain general color conversion settings, but also specific color builds, for either the spot colors you use the most, or for a whole Pantone book.
These color builds determine the exact percentages of the available output inks that will be used to print the corresponding spot colors. These have often been adjusted by your color expert to give you the spot color simulation you want.
2. In Undefined Spot Colors, choose what to do when the file contains a spot color for which your color strategy has no color builds.
41
23
Automation Engine
• Select Do not convert (keep in output) if you want to leave the spot color untouched in the output file. Do this for example if you are using certain spot colors as extra output inks (typically white or metallic inks).
In this case, the task will end in a warning.
Tip: Consider to set up your workflow so that:
• the output file gets sent to the next task automatically (if you are sure that those spot colors are extra output inks),
• further processing of the output file is paused, so that you can check whether those spot colors are actually extra output inks.
• Select Convert to convert that spot color to the color strategy's output profile using the strategy's general color conversion settings (see the
Color Engine Pilot documentation
for more information about color strategy settings).
• Select Generate error if you don't want to convert the file at all, and instead have the task end in error.
Do this if you always make a color build for each spot color, so in this situation you want to stop the workflow and investigate why this is not the case here. You may want to either replace the spot color in your file, or add a color build for that spot color in the color strategy.
3. Select Hide Technical Inks if you want to keep technical inks out of the conversion.
4. Select Flatten document if you are experiencing unexpected color results when converting files containing overprints, transparencies or vignettes.
Flattening your file resolves its overprints and transparencies, and converts its vignettes to images.
In the example below, the original file contains three objects:
• the background (sky),
• the lighthouse, which is knocking out on the background object,
• the wave, which is overprinting on both the lighthouse object and the background object.
Flattening your file replaces the parts of objects that were overprinting or transparent by other objects. Those new objects have the color that was resulting from the overprint/
transparency, but are not overprinting or transparent.
42
Automation Engine
23
Attention: We recommend that you:
• flatten files with overprints, transparencies or vignettes,
• don't flatten files that you still need to trap or edit afterwards.
If you need to both flatten and trap your file, make sure to do your trapping first, and place the Convert Colors with Equinox task towards the end of your workflow, as close to the output device as possible.
5. For CMYK objects, you can choose to Convert either:
• Images and Linework,
• Linework only.
• Images only.
Attention:
• If your file contains a Device N image (an image that contains one or more spot colors), its spot color(s) will be converted even if you select Convert Linework
only.
• Flattening your file converts vignettes into images. This means that:
• If you selected Flatten document, vignettes will be color converted when you chose to Convert Images and Linework or Images only.
• If you didn't, they will be converted when you chose to Convert Images and
Linework or Linework only.
43
24
Automation Engine
24. Convert IMP file to Normalized PDF
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
44
Automation Engine
25
25. Convert Selection
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
45
26
Automation Engine
26. Contourize & Clean
This old technology is still supported but no longer commercially available.
Please find its documentation in the
manual of Automation Engine 14.1 or older
(as part of the
Reference Guide).
46
Automation Engine
27
27. Copy or Move File
This task copies or moves the input file or Marked files to a new location.
Note: To Mark a file, insert the
Mark File
workflow control in your workflow. Learn more in
Mark File and Select Marked File
.
You can also launch this task on folders.
• Select the option if you want the task to
fail when the file to be copied or moved already
exists in the output folder.
• You can also choose to not take over the Extension of the Input file in the Output file.
Note: When the files that you move or copy with this task have
prepared view files for the
Automation Engine Viewer
, these view files will also be moved or copied. This is also done with the XFDF annotation files that were created by any
Inspection task
that you launched on the files that you here copy or move.
47
28
Automation Engine
28. Create CAD Sheet
Concept
This task places graphic files on the stations defined in a MFG, DXF or CFF2 file. This task allows to fully automate the folding carton step and repeat process, based on information from the business system (MIS, ERP).
Which graphic files are placed is decided by the task's input file(s):
• If the input file is an XML file, this XML needs to contain information on what graphic file(s) to use, the quantity, bleed etc.
• If the input file is a PDF file, the PDF is placed on all stations. If the input is multiple PDF files, the files will be distributed equally.
Learn more in
Distributing the One Up graphics onto the Stations
XML input
The task looks for a <JOB> element in the XML file.
Attention: All XML elements are case sensitive. The element <JOB> must be in capital letters.
An example:
It's also possible to combine multiple graphics in the XML file. In that case, multiple <JOB> elements are gathered in one <JOBS> element. An example:
48
A <JOB> element can contain the following sub elements:
XML
Element
Description
Filename
(mandatory)
URL of the graphics. Both File URL and UNC paths are supported. Both absolute
URLs and relative URLs are supported. In case the URL is relative, the
Graphics
Automation Engine
28
XML
Element
Description
Folder specified in the ticket is used to resolve the URL of the graphics. Only one of FileName or ProductID may be specified. Some examples:
<FileName>file://myserver/myfolder/mygraphics.pdf</FileName>
<FileName>\\myserver\myfolder\mygraphics.pdf</FileName>
<FileName>mygraphics.pdf</FileName>
<FileName>myfolder\mygraphics.pdf</FileName>
Product ID
(mandatory if
Filename is not used)
ID of the Product to use for the graphics. The first Product Part is placed on the
Front side and the second Product Part is placed on the Back side (if any). Only one of FileName or ProductID may be specified.
Quantity
(mandatory)
DieShape
Number of times the graphics needs to be placed. Set the value to Maximum to fill the CAD file with as many graphics as possible.
Ink name of the die line of the graphics.
Bleed Sets a bleed mask, in mm, starting from the die line.
Page@numberWhen no page number is defined, the first page of a multi-page PDF is used. Set the page number if you want to use a different page.
Extra XML Parameters when working Front and Back Graphics
Table: Back side handling in XML
XML
Element
Description
BackGraphic URL of the graphics for the back side. Example:
<BackGraphic>file://myserver/myfolder/mybackgrphic.pdf</
BackGraphic>
RectoVerso Value = 1 indicates that the graphic specified under 'FileName' is a multipage
PDF file where the even page(s) are the back side graphics. Example:
<RectoVerso number="1"/>
Attention: The default is <RectoVerso number="1"/> . In other words, even when the XML file does not contain a setting for backside and the supplied graphic is multipage, the even page(s) will be used as back side graphics.
SameGraphic Value = 0 indicates that the front graphic should also be used as the back graphic. Example:
<SameGraphic number="1"/>
49
28
Automation Engine
XML
Element
Description
FlipGraphic A value = 1, in combination with 'SameGraphic' = 1, indicates that the front graphic will appear also on the back but flipped around a vertical axis. Example:
<FlipGraphic number="0"/>
28.1 Ticket settings
General tab
50
• The Output Format can be a PDFPLA, a Normalized PDF (with all references embedded) or a native PDF.
• Screen Registration: De-select this option if the RIP should reset the screening origin for every one-up. Select it to keep the same screening origin for the complete step and repeat.
This option is only available when outputting to PDFPLA or Normalized PDF.
• Use the Backing Up when working with a front and back. You can choose to Work-and-
Turn (rotate over a vertical axis) or Work-and-Tumble (rotate over a horizontal axis).
Note: In order to make a CAD sheet with a front and a back, you need a multi-page PDF file.
The first page is placed on the front, the second on the back. In case of XML input, the XML file can contain
more detailed settings for the back side graphics
• Check Add SmartMarks if you want to add any.
Click Options... and select them from the drop-down list or use SmartNames (Front and/or
Back).
• By default, marks are loaded in a layer on top of the graphics. Check
Load Mark Set
in bottom layer if you want to make them appear behind the graphics, in a new layer at the bottom. This is used for example when adding gradation strips that need to run behind the graphics.
• Use Pull back Marks to keep marks away from the graphics. For example to keep gradation strips away from the die line, with a set distance. This option is only available when Load Mark Set in bottom layer was checked.
Automation Engine
28
• Limit Bleed: The bleed can be limited to a specific distance. The bleed mask is created by spreading the die shape.
• The Graphics Folder is the folder where the task searches the graphic files. This option is only applicable in case the input mode of the task is XML and when the XML does not offer a full absolute path (only a partial path or only the name of the input file). Learn more in
on page 48.
CAD tab
• CAD File: Define the MFG, DXF or CFF2 file that will be used as base for this sheet.
• Mapping: When the CAD file is a CFF2 or DXF file, you here select the set of mapping rules.
These rules map line styles (cut, crease, bleed), layer names and color numbers onto
ArtiosCAD line types. These sets of mapping rules can be created in Esko PackEdge or Plato.
Learn more in the user documentation of these editors, more specifically in their section on placing files (PackEdge) or on importing CAD data (Plato).
• The CAD Style changes the appearance of the (imported) ArtiosCAD type lines. The styles you can select here were also created in PackEdge or Plato. Learn more in the their user documentation, more specifically in the section on placing ArtiosCAD files, and the option for "CAD Style".
• The filling order determines in which sequence stations will be filled with one ups and it also determines the value given by the SmartMark 'Station Number'.
Use Set custom filling order to specify a filling order that is different than the one defined in the selected CAD file.
The filling order is defined by selecting a Start Position, Direction and type of Filling
Order. Learn more about using SmartNames to define these buttons in
SmartNames of
Parameter Values
.
Note: The sequence of the designs is determined by taking the center points of the designs and sorting these in rows and columns. Keep in mind that designs with different sizes or layouts with staggered designs can result in more rows or columns than expected.
Plate tab
51
28
Automation Engine
The sheet size can be automatically extracted from the CAD template but neither Artios MFG nor CFF2 have a notion of 'plate'. As a result the plate size and position of the sheet on the plate have to be specified in this Plate tab.
Plate Size: You here specify the plate's horizontal and vertical size. Below, in Sheet Position on
Plate, you specify the relative position of the created sheet.
Shrink: To compensate for distortion on the output device, you can add vertical and horizontal shrink values.
• When the output format is PDFPLA or Normalized PDF, this task writes the shrink factors in the file's XMP section. This means that the objects and page boxes keep their original sizes.
These shrink factors will then be picked up by the RIP or export ticket, where they are used as scale factors and are applied on the complete document.
• When the output format is native PDF, this task applies the shrink factors as scale factors on the complete document.
Position the sheet on the plate by dragging and dropping the blue square (the sheet) to the right position on the grey square (the plate). Define any extra horizontal and vertical
Sheet
Offset.
Tip: When using SmartNames, make sure they return a value that the field expects. For example a SmartName in the field 'Plate Size' should return a number.
Sheet tab
52
Automation Engine
28
If you want to use a custom sheet size instead of the Sheet Size defined in the CAD file, enable
Set custom sheet size and enter the dimensions for the sheet.
You can also specify a custom Blank Position instead of using the position defined in the CAD file by enabling Set custom position. Using the Blank position, you can position the bounding box of all cut lines on the sheet.
Position the blank on the sheet by clicking or dragging the blue square (the blank) in a position versus the grey square (the sheet).
Then, based on that position, you can define a horizontal and vertical Blank Offset.
28.2 Positioning a One Up graphic onto a Station
To decide how to position a PDF onto the CAD file, the task tries these options, in this order:
1. Checks if the input PDF contains a die cut object, a linked ARD file. If the name of this ARD file matches the name of the design specified in the MFG file, the graphics will be placed.
Note: This option is only available for Normalized PDF files.
2. Positions the Trim Box of the PDF on the bounding box of the cut and crease lines. If the
Trim Box and bounding box match, the graphic will be placed.
3. Positions the die line of the PDF defined in the XML file, on the bounding box of the cut and crease lines. If it matches, the graphic will be placed.
Note: This option is only available when the task input file is an XML file.
If the PDF Trim Box or die line bounding box does not match any of the bounding boxes of the design in the CAD file, then the file will not be processed and an error will be given.
53
28
Automation Engine
28.3 Distributing the One Up graphics onto the Stations
Which PDF goes onto which position in the CAD layout?
• When the input file of the task is an XML file, the task looks for an XML element Quantity, defining the amount of stations to be filled with that specified graphic. For example
<Quantity>10</Quantity>.
Note: If the total number of quantities doesn't match the number of stations, the task will stop with an error.
When the element shows the value <Quantity>Maximum</Quantity>, the task will place the referred PDF file as many times as possible.
When more than one PDF file has the quantity element set to Maximum, the task will distribute the referred PDF files equally. You can also combine files with a fixed quantity with one or more files with a quantity set to Maximum.
• When the input file of the task is PDF, the task will consider all PDFs to be set to maximum quantity, so the provided input files will be distributed evenly onto the provided CAD layout.
When the number of available stations cannot be divided by the number of input files (for example 9 stations and 2 PDF files), the task will automatically distribute the remaining
stations.
54
Note: When the CAD file contains different designs (different types or sizes of boxes), the graphics will only be distributed on the corresponding (fitting) designs (see
Positioning a One Up graphic onto a Station
on page 53).
Automation Engine
28
28.4 Bleed and overlap
When the one up graphics contains bleed, this bleed will be used around the die line, limited by the value in Limit Bleed (in the General tab).
Note: Everything outside the die line is considered to be bleed. Bleed zones without content will knock out when overlapping. Overlaps can only work well if a correct bleed limit is applied.
When the bleed of two stations overlap, you can have these situations:
• There is a gap between the panels of the two stations.
In this case, centerline overlapping is applied, so the bleeds from both neighboring stations touch on the center-line of the gap.
• The station panels are touching.
In this case,
• the biggest panel will overlap the smaller panel (situation A in the example below).
• if the panels are the same size, centerline overlapping is applied (situation B in the example below).
• in case the ArtiosCAD artwork panels were given a specific ' Allow Bleed' property, other
Bleed Overlap Priority Decided by ArtiosCAD Artwork Panels
on page 56.
Note: When deciding if a station is touching another station, minor tolerances are taken into account to cope with small inaccuracies in the die cut file.
55
28
Automation Engine
28.5 Bleed Overlap Priority Decided by ArtiosCAD
Artwork Panels
The priority in bleed overlap can be automatically decided in case the layout is an MFG and in case there are common knives (i.e. no gutters, so areas where 2 panels/flaps touch). The decision is then based on how the ArtiosCAD user defined the bleed direction for those specific panels.
In ArtiosCAD (v 14.0.2 or higher), a panel can be defined as an ' artwork panel' and an artwork panel can have an ' Allow bleed' property. A panel that is set to allow bleed is considered as having a minor priority and it can receive bleed when it touches another panel marked as major priority (where ' Allow bleed' was not defined or turned off). In the case 2 minor panels are touching, the bleed will be truncated to the centerline, which is the default behavior, like in areas where there are gutters (i.e. no common knives).
Note: This behavior applies to all Step and Repeat tasks using an MFG layout (including in
Plato).
Overview of all Possible Situations:
• In case there is a gutter: always centerline truncation.
• In case there is no gutter between 2 panels (gutter = 0), the following overview applies:
Table: Smart Flapping
Panel 1 Panel 2 Bleed Action
Not an artwork panel Not an artwork panel Compare size of Panel 1 and Panel 2. If size difference > 10%, then large one bleeds into smaller one, otherwise centerline is used
Centerline (i.e. no bleed as the gutter = 0) Not an artwork panel Artwork panel with allow bleed = 0
Not an artwork panel Artwork panel with allow bleed = 1
Panel 1 bleeds into Panel 2
Centerline (i.e. no bleed as the gutter = 0) Artwork panel with allow bleed = 1
Artwork panel with allow bleed = 1
Artwork panel with allow bleed = 0
Artwork panel with allow bleed = 0
Artwork panel with allow bleed = 1
Artwork panel with allow bleed = 0
Artwork panel with allow bleed = 0
Artwork panel with allow bleed = 1
Panel 2 bleeds into Panel 1
Centerline (i.e. no bleed as the gutter = 0)
Panel 1 bleeds into Panel 2
56
Automation Engine
29
29. Create ArtiosCAD Report from XML
This task is set up by an Esko Solution Architect.
For more information, search for online articles on this topic in the
Esko Knowledge Base
.
57
30
Automation Engine
30. Create Design (DesignWizard)
This task creates variants of a template design. The differences in the variants are described in an external file.
Attention: The template design needs to be made in Esko PackEdge.
This template design contains objects generated by SmartMarks (text, colors, objects, external files)
The DesignWizard task regenerates the SmartMarks using different data sets. These data sets can come as a field in a database (accessible from the Automation Engine server through
ODBC), or they can come from fields in an XML file.
An example: These resulting juice designs vary in color, text and bar code. External references can also vary (images, logos).
The task used this XML file that describes their differences.
58
Automation Engine
30
Learn more about how SmartNames can retrieve values from an XML file or directly from an
Using SmartNames in a DesignWizard template
30.1 Using SmartNames in a DesignWizard template
The DesignWizard template picks up it the variant values via SmartMarks that use
SmartNames.
In the case of a live connection to a database, you create and use
Database Query SmartNames
.
In the case of XML files, the XML file is expected to have a similar format as when saving a database query into an XML file. This means the data can either be split over 1 file per instance
(i.e. each XML file contains all the data for 1 variant) or there can be multiple sets in 1 XML file
To get SmartNames out of such an XML file, you need to Load it into
Parameters tab of the Job
Setup
. Each new Job Parameter so automatically becomes available as a SmartName (inside this Job)
59
30
Automation Engine
60
Automation Engine
31
31. Create IMP File
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
61
32
Automation Engine
32. Create Imposition from JDF Layout
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
62
Automation Engine
33
33. Create Imposition from RunList
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
63
34
Automation Engine
34. Create Job task
This task is documented in the chapter
Integrating with External Systems
. Find a direct link
here
.
64
Automation Engine
35
35. Create or Modify WebCenter Project
This task is documented in the chapter
Integrating with WebCenter
. Find a direct link
here
.
65
36
Automation Engine
36. Create PAF / JPG / XML (LinkEdge)
Note: The name of this tool refers to "LinkEdge", an old interactive tool that was used to transfer files from the editor PackEdge between different sites.
This task packs the graphics data all its references in one file. It is also used to unpack that set of data, possibly at another site. This task is not just a form of Esko-'Zip': The (un)packing process also communicates with central resource folders (colors, fonts).
The task also offers to create a preview (JPEG) and/or a description of the file (XMP-XML).
You can also use the task to for example only create one of those 3 types of data.
36.1 Pack/UnPack
66
• Select Create Packed File to create a Pack file from a Normalized PDF or Plato PLA file (and legacy file formats GRS and GRQ).
When your ticket does not yet have an input file selection, you still need to choose the
Action:
• Pack File: This creates a .PAFSC file (.PAF when input file was a legacy .GR* file)
Note: 'PAF refers to Packed Archive File'. The 'SC' refers to 'Scope', a term used in old
Esko workflow setups.
• UnPack File: The output file is written in the ticket's Output folder. Where the
referenced files are written depends on
.
• You can choose to Include Fonts. When unpacking, the task first checks if the font is installed centrally. If so, the graphics file will refer to that central font. Otherwise, the font is installed locally.
• Unpack in Local Directory:
The Local Directory is the output path in the ticket. When none was specified there, it is the folder of the input file. This option is important when there are referenced files:
Automation Engine
36
• When this option is not selected, the task will try to restore the original file structure.
When a path to a reference is no longer relative but refers to other disk drives, these data will be put in a subfolder 'External'.
• When this option is selected, all elements of the packed file will be unpacked in the same output folder.
An example:
Suppose you packed a Normalized PDF (D:/Jobs/2345banana/2345_50ml.pdf) which has one referenced image that resided in a subfolder (D:/Jobs/2345banana/ images/banana.eps ). When you unpack the PAFSC file and there select Unpack in
Local Directory, the task will write all files in the same folder. If you unpack without that option, the task will try to re-create the same subfolder and put the image there. In this case, again in a subfolder /images .
• Add a Password to protect the Packed file. The user that unpacks that file will be prompted to enter the password (using a task ticket or using an interactive tool).
36.2 XML
Select
Extract XML Report if you (also) want to create an XML description of the file's XMP metadata (job and customer data, references, inks, barcode, etc.).
Note: Native PDF data will first automatically be normalized according the ticket configured
here
.
XML Structure: choose between standard XMP and the old BackStage Version 1.2 (also based on XMP, but contains less information).
Note: Learn more about Esko XMP in the white paper "XMP Metadata". Find it under "Related
Documentation"
next to the Automation Engine documentation
.
Choose the Units that should be used in the XML file.
Select Ignore opacity mask inks if you do not want information about such inks in the XML.
Learn more about opacity mask in the user manuals of Esko or Adobe editors.
67
36
Automation Engine
36.3 JPEG
Select Extract JPEG Preview if you want the task to (also) create a preview file of the
(unpacked) input file.
Note: Native PDF data will first automatically be normalized according the ticket configured
here
.
68
• Define an Image Resolution.
• Alternatively, you can define the JPEG's Width and Height in pixels. If your ticket already has an input file, these fields will already be filled in. Changing these fields may automatically reduce the chosen resolution.
• Alternatively, you can set limits to the JPEG's Width and Height. Changing these fields may automatically reduce the chosen resolution.
• Choose a Compression from the drop-down list.
• Anti-aliasing smoothens the staircase effect you get in the generated images of line-art objects. If you select it, also select it's quality.
• Select Account for Margins if you want the JPEG to also contain data from outside the file's
Trim Box ('borders'), so up to the file's Media Box ('margins').
• Select Use varnish inks in output if you want the inks with the attribute 'varnish' to be included in the JPEG file.
• Page Range: Choose if you want a JPEG of All pages or of a specified range of pages (for example '2-3,5-6').
Automation Engine
36
69
37
Automation Engine
37. Create PDF File from JDF RunList
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
70
Automation Engine
38
38. Create PDF File from RunList
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
71
39
Automation Engine
39. Create Merged Plate
This task is documented in the chapter
CDI Platemaking Workflow
. Find a direct link
here
.
72
Automation Engine
40
40. Create Master DCS File
This old technology is still supported but no longer commercially available.
Please find its documentation in the
manual of Automation Engine 14.1 or older
(as part of the
Reference Guide).
73
41
Automation Engine
41. Create Report (ReportMaker)
Attention: This task requires templates made in Esko PackEdge.
This task is used to automate the creation of design 'print cards' (in French: "fiche technique", in German: "Druckkarten").
These file reports typically contain a preview of the design and then list all kinds of information related to the job-order, customer, extensive details of graphics and CAD. It can even be extended to show separations or include 3D objects. Such file reports is what many customers used to create manually and then print out or use as proofs.
The task makes a report based on a Report Template. Learn more below in
on page 75.
Task Settings
• To avoid that the output PDF has the same name as your input file, it is by default named
[File]_Report.pdf. Use SmartNames to define any other File Name.
• Select a Report Template.
• If you want your report to be a self-contained PDF instead of a Normalized PDF, select
Export to PDF and choose a Ticket for the PDF Export task.
Tip: You can also use this option to help create a report containing a 3D object (see
Adding a 3D Object to a Report PDF
Example
Here is an example of a report (viewed in Adobe Acrobat). The format and content is decided by the Report Template, also the amount of pages. This report template had a second page where SmartMarks place the design in separation mode:
74
Automation Engine
41
41.1 Creating a ReportMaker Template
Remember: You need the editor Esko PackEdge to make a template for the ReportMaker task.
A ReportMaker template is a Normalized PDF which you can design yourself. In this file, various specific SmartMarks are needed. Some of them use specific SmartNames.
Let's make a simple template that can give us this result:
75
41
Automation Engine
In the above example, 1, 2 and 3 are all Text Marks on board the template that are resolved when the ReportMaker task is executed. Number 4 shows a preview of the input file. This was
placed via an Image Mark and can be scaled at wish.
76
Note: SmartMarks used in a ReportMaker template are extra smart because:
• Ink related SmartMarks show the inks of the input file, not of the generated report.
• Ink coverage related SmartMarks show the ink coverage of the unscaled version of the input file.
Follow these steps to create a template for this task:
1. In PackEdge, create a new file that you will use as a report template.
2. Place the Text Marks. When needing help, contact Esko or check the
PackEdge user manual
.
Automation Engine
41
3. Draw a rectangle where you want the preview to appear (no need to attribute any color).
4. Make that rectangle a Named Object:
5. In the SmartMarks dialog, select that object, click
and add an Image Mark.
6. In the tab Image, the Name of the image is a special Smart Text for this case. Click and choose '[taskinputfile]' from the category 'ReportMaker'. This is a special SmartName that will place the input file in the Report when so asked by a ReportMaker task.
7. In the tab Position, Attach the Image Mark to the Object that you created in step 4:
77
41
Automation Engine
Notice how the Image Mark 'taskinputfile' has the same functionality as any other
SmartMark. It can also be scaled, you can make ink-selections etc.
8. This is the result so far, the Image Mark places the 'taskinputfile' in the Named Object:
78
Automation Engine
41
9. Save your PackEdge file.
10.Test it by using it as a ReportMaker template.
41.2 Adding Previews of Details in a Report PDF
The previews in a ReportMaker report can also zoom in on ‘
details’ of the input file. This makes it possible to add extra previews where you zoom in objects that are difficult to inspect in a full preview (ingredient copy, small logos, bar codes...). This is also useful when the design only contains few graphic objects, for example on corrugated boxes.
Here's an example where page 3 and 4 of the report zoom in on important content of the design:
The way to do this is very similar to how you create the placeholder for the preview of the complete task input file, as described
. In this case however, we will
place a detail of the input file. These details are then attached to their own Named Objects. You can for example put these on extra pages of the template.
See below how page 4 of the template, that was used in above example, was set up:
Attention: Important is that in this case, the named objects that indicate the details first need to be set up in the input file. So before you launch the ReportMaker task, your input file needs to contain these Named Objects too.
79
41
Automation Engine
Note: A Named Object is typically a rectangle. This contour object is used as a clip mask on the input file. If the named object is a different object (an image, a group of objects…), then a clip mask will be applied with the size of the bounding box of the named object.
41.3 Adding a 3D Object to a Report PDF
A report PDF can even contain a 3D object of the input file. To do this, you need:
• a report template with image marks allowing 3D objects,
• a Normalized PDF file with a link to a CAD file (.ard, .dae or .zae).
Follow these steps:
1. In PackEdge:
a) Open your report template in PackEdge.
b) Add a Named Object in which you want the 3D object to be placed.
c) Add an Image Mark to that Named Object.
d) Add Smart Text to define the name of the Image. From the category 'ReportMaker', choose '[taskinputfile in 3D]'.
80
Automation Engine
41
e) Save your template.
2. In Automation Engine:
a) In the Create Report ticket, make sure you select the option 'Export to PDF'. This forces the 3D object to be embedded in the PDF.
b) This report PDF and its embedded 3D object can be viewed in Adobe Reader 8.0.1 or later.
81
42
Automation Engine
42. Create RunList
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
82
Automation Engine
43
43. Create RunList from PDF
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
83
44
Automation Engine
44. Create Sheet Report from IMP File
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
84
Automation Engine
45
45. Create Tiles
This task is described in the chapter on
Gang Run Printing
. Find a direct link
here
.
85
46
Automation Engine
46. Create Wrapper File
Concept
The task wraps the input file(s) in a Normalized PDF. This is typically used to encapsulate screened TIFF ('Copydot') files into a PDF format before further tasks are launched on that PDF.
This task accepts these types of images as input files: TIFF, TIFF_IT, PSD, JPG, BG_CT, BG_LP,
BG_JS, EPS, DCS, Copydot
Combine multiple input files (separations) to a single composite wrapper file: This is the
default behavior with multiple input files. Learn more in
on page 88.
46.1 Page Size tab
86
• Page Size: You here define the size of the output file.
• Job size: This is the size of the input file.
• Choose
Custom to define a size manually.
• Or select a standard size from the list.
Note: About 'Scanner Trim Size': All 'Eskoscan' scanners have a feature to indicate the trim size of the page (they add it into the master DCS file). When choosing 'Scanner Trim
Size', the borders of the output file will be automatically positioned.
• Offset: When no offset is defined, the center of the 'image' will be positioned on the center of the page. If the page is smaller than the image (width, height, or both), then margins will be set that enclose the image completely. The size of the margins will not be fixed. Margins indicate the differences between the image size and the user-defined page size.
• Select Margins and define its values to set fixed size margins to the PDF (for example 3 mm for bleed).
• Reader's Spread: None of the supported input file types have the notion of 'reader's spread'. Select this when you want to use the output PDF in Esko FastImpose.
Automation Engine
46
• Single Page forces a single page output file.
• Reader's Spread forces a reader's spread output file, set as double pages.
• Auto checks the size of the input file: When its width equals or exceeds two times the selected page width, the reader's spread option is set. Otherwise it is treated as a single page.
• Page number: Select the correct page number from the output PDF that you want to output.
• Display images: Select the preview settings of the output PDF.
46.2 Inks tab
This tab serves to add ink attributes to inks that can be detected from the input file.
Note: This tab is greyed out when you selected the option 'Combine multiple input files
(separations) to a single composite wrapper file'.
If an input file contains definitions for its ink (for example a CMYK Tiff or a Photoshop DCS2), and this definition matches an Ink Name defined in this tab, then the Angle, Ruling, etc. in the output PDF will be the ones as set here for this ink name. All other inks will get the attributes as set in the Default options set below.
This tab by default contains CMYK. You can change at will manually.
Inks in this list can be selected or not. Not selected inks will be ignored by the task.
When an input file has no ink definition:
• If only one ink is selected in this tab, the output PDF will contain that ink, including all its attributes as here specified.
• If multiple inks are selected, and K is part of that selection, the output PDF will contain K and its attributes as here specified.
• If multiple inks are selected and K is not part of that selection, the output PDF will contain the first ink from this list and its attributes as here specified.
87
46
Automation Engine
• If no ink or the wrong ink is selected (one that cannot be found in the Pantone or Designer book), then the output PDF will contain K with the Default attributes.
• If the wrong ink is selected, together with the default ink, then the output PDF will contain the attributes from the default ink.
Tip: In Preferred Ink Book, choose the ink book that you use most frequently. When you then type an ink name in the table, the task searches for this ink in your preferred ink book first. For example, if you type the ink name '154' and your preferred ink book is set to Pantone Colors
Uncoated, the task will automatically suggest the ink 'PANTONE 154 Uncoated'.
Overprint: Select one from list. Learn more in
46.3 Separations tab
This tab serves to define which ink each of the input files should be attributed:
Wherever possible, the task will try to define the ink automatically.
If you want to overrule these, select the Ink Type and name yourself.
88
Automation Engine
47
47. Create XML File
This task is documented in the chapter
Integrating with External Systems
. Find a direct link
here
.
89
48
Automation Engine
48. Crop LEN file
This task is documented in the chapter
CDI Platemaking Workflow
. Find a direct link
here
.
90
Automation Engine
49
49. Data Collector
This Workflow Control is documented in the chapter "Workflows". See
Data Collector
.
91
50
Automation Engine
50. Data Splitter
This Workflow Control is documented in the chapter "Workflows". See
Data Splitter
.
92
Automation Engine
51
51. Delete File
This task is mostly used at the end of a workflow ticket, where the original input may be deleted since the workflow has created other data that are more worth keeping..
Tip: This task can also be combined with the Wait task. For example: first wait 2 hours, then delete the marked file.
Tip: To delete marked files, you can perform the following actions: Mark File + any other action + Select Marked File + Delete File.
93
52
Automation Engine
52. Download WebCenter Document
This task is documented in the chapter Integrating with WebCenter. Find a direct link
here
.
94
Automation Engine
53
53. Enrich Black
This task creates "rich black" areas. Typically cyan is added to make black areas more black.
You can also use this task to enrich areas in other inks than 'process black'.
This task uses the trapping technology as used in the
. It also scans and then creates (overprinting) objects, which is stores in an extra layer named "Trapping".
In the example below, 80% Cyan is added to all areas containing pure black, resulting in an enriched black:
•
•
53.1 General Tab
• Add Inks: You here define what color will be added. This color can contain up to four inks.
Typically 80% C is added to generate rich black, or a more neutral combination of CMY such as 60% C 40% M 40% Y. Alternatively, you can type in the name of any other ink. When the percentage next to an ink name is set to 0%, the ink will not be used.
• Choke Distance: To prevent registration errors on the press, you here define a value so that the generated objects in the added color will be smaller than the original (black) area. This value is the distance between the edge of the area in the defined color and the edge of the original (black) object.
95
53
Automation Engine
, this option is named Pull Back.
• Corners: You here specify how sharp corners should be handled.
•
Mitered: If the distance from the base of the trap to the corner point is larger than the Miter Ratio multiplied by the trap distance, then the corner will be beveled.
Otherwise, it will remain sharp.
•
Round: All corners end in a round cap.
•
Beveled: See this cut-off shape in the graphic:
• To:
Define the color of the objects that you want to enrich with the above set ink(s). This ink is typically Process Black. Alternatively, you can type in the name of any other ink.
• Minimal Density: Define the minimum percentage that the To ink needs to have in an area before the specified color will be added to that area.
53.2 Scan Tab
96
Automation Engine
53
• Objects:
• All: All objects in the file will be considered.
• Green Selection: Only objects that were saved as a green selection in PackEdge will be considered.
•
Close Gaps smaller than: Learn more in the page on the
.
• Restrictions: Define which objects can be ignored (this also speeds up the task):
• Patterns: Ignores native "fill and stroke" patterns. Prior to creating the new objects, fill patterns are converted to contours. Fine patterns can so result in a huge number of contours, making this a long and memory heavy task.
• Bitmaps: Ignores bitmap pixel data. This type of data is also contourized before the new objects are created, which can slow down the task.
• Overprinting Native Blends: This option is only used in a DeskPack workflow. Certain native Adobe Illustrator blends cause performance issues. You may ignore these because they have little or no effect on the result of this task.
• External Objects: Ignores references to external Normalized PDF files (or legacy GRS, LC, and LP files). When this option is not selected, the external references are degraded to internal objects prior to creating the objects.
• Existing Trap Layers: Ignores any already existing layers created by this task. This option is useful when re-launching this task on a file that already has such a layer.
• Don't Trap Text smaller than: Small text must be kept as sharp as possible. The task risks to blur the sharp edges of small characters, making them harder to read.
The default value is 0 points ; it then creates objects for all text. 1 point equals 1/72 of an inch.
This option only affects live text objects, not contourized text.
• Allow Different Settings for One Color Pair:
The task can generate a different "trapping" action for different occurrences of a same color pair.
• Yes is the default value.
• Select No to force the task to apply one identical action to all the occurrences of a same color pair.
• Select Only for objects bigger than to force the trap expert to apply one identical action to occurrences of one color pair belonging to small objects, and to allow different settings for the occurrences belonging to the bigger objects.
97
54
Automation Engine
54. Expand Dynamic VDP Data
This task creates PDF/VT files from a database containing variable data, using a VDP template
(VDT file).
This task requires:
• a CSV database as input
• a VDT template.
98
Database File:
• Encoding: Choose the correct character encoding to ensure accurate interpretation of the database entries.
Note: The default encoding is UTF-8. This is also the recommended encoding.
• Field Separator: Let the task Detect automatically or choose , (Comma), ; (Semicolon),
Space or Tab.
• Empty lines: Choose what needs to happen with empty lines in the input CSV file. Only lines ending with CR, LF or CR LF can be detected as an empty line (it is possible to mix different line endings in a single file). All empty lines at the end of the file are skipped.
• Field Names: Field names map data chunks from the database entry to its corresponding
VDP template items. Choose from:
• From CSV File: When selected, the task will extract Field Names from the first record of the CSV file by default.
Attention: Field Names can only contain the following characters: lower- or upper-case ASCII letters ("a-z, A-Z"), digits ("0-9") or underscore ("_").
• From Header File: When selected, define a Header File that contains the Field Names.
Such a file
• should contain a single line specifying the
Field Names
• should have a Field Name corresponding to each column in the CSV file.
Automation Engine
54
• and the CSV file must use the same delimiter and encoding.
• Header File: (described above). Browse or use SmartNames to define this file.
Dynamic VDP:
• Template: Define the VDP template file that contains artwork and the placeholders necessary to generate the task output.
Note: The VDP template can be created and exported using Dynamic VDP DeskPack Plug-in for Adobe Illustrator.
• Image Path: If the database file has image references, provide the Image path.
99
55
Automation Engine
55. Export ArtiosCAD Design Info
This task exports an ArtiosCAD design to an XML file. This XML file is then interpreted by an external system. This task is also usually launched by that external system.
This task is set up by an Esko Solution Architect.
For more information, search for online articles on this topic in the
Esko Knowledge Base
.
100
Automation Engine
56
56. Export ArtPro to Normalized PDF File
This task converts an ArtPro file to a Normalized PDF file.
• Preferred Ink Book: Select the ink book the task should check first when processing inks that are not in the predefined ink books, or inks that may be listed in several ink books.
For each ink in the ArtPro file, the task will:
• first look in the predefined ink books (such as the 'process' and PANTONE ink books),
• then in the Preferred Ink Book defined here.
• If it still doesn't find the ink, it will check the other ink books you created.
• If the ink is not present anywhere in the color database, it will be saved as an unregistered ink.
•
Search for missing images in: When the ArtPro file contains links to images that the task can't access, you can copy those images to a folder within an Automation Engine Container, and browse to that folder here.
• Embed all images: Embeds all images referenced in the ArtPro document into the PDF file.
• Add non-printable layers: When selected, layers set to "non printing" are also exported into the PDF file.
• Add fully transparent objects: When selected, objects that are completely transparent will be included in the PDF file.
• Folder Mapping: When the ArtPro file contains links to images that reside on a Mac OSbased file server, you can mount the drive of the Mac OS server on the Automation Engine server and use this 'Folder Mapping' table to keep the links to the images working in the output file.
To map folders from the ArtPro file to the Normalized PDF file:
1. Click Add.
2. In the Client column, type the drive name on the Mac OS system.
3. In the Server column, type the drive letter that is used to mount the Mac OS drive on the
Automation Engine server.
101
56
Automation Engine
For example, in our ArtPro file, the path to an externally linked image is:
Intel_Mac:images:image1.
We mount the Intel_Mac drive of the Mac OS file server on our Windows-based
Automation Engine system, using the drive letter G:\.
The task will find the images when you map the folders Intel_Mac to G:\ .
102
Automation Engine
57
57. Export IMP File to GRI File
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
103
58
Automation Engine
58. Export IMP File to JDF Layout
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
104
Automation Engine
59
59. Export IMP File to JDF Post-Press
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
105
60
Automation Engine
60. Export IMP File to PDF File
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
106
Automation Engine
61
61. Export IMP File to PDF File Chain
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
107
62
Automation Engine
62. Export IMP File to PostScript File
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
108
Automation Engine
63
63. Export Imposition to JDF Layout
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
109
64
Automation Engine
64. Export Imposition to PDF File
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
110
65. Export Nested Layouts
This task is described in the chapter
Gang Run Printing
. Find a direct link
here
.
Automation Engine
65
111
66
Automation Engine
66. Export Step and Repeat to JDF Layout
This task exports a Step and Repeat layout to a "JDF Layout" file that contains references PDF
1.5 files containing the stations, masks and marks.
You can choose the JDF Version: 1.2 or 1.3.
Create MIME file: Select this to get the JDF and the referenced PDF files all together in a MIME packed file.
112
Automation Engine
67
67. Export to 3D
Concept
This task creates 3D files which you can view in 3D viewers. The input file needs to be a
Normalized PDF or PDFSTA (Station file) that links to a structural design (CAD) file.
About Structural Design Files
A structural design file (2D and 3D) contains all the cut and crease lines for a specific shape.
It can also contain folding angles that define how it should be folded into its final shape. A structural design file does not contain the graphics, only the definition of the shape.
The link between a graphics design and its structural design (shape) can be done in an editor
(ArtPro, PackEdge or Adobe Illustrator (using the Esko
Data Exchange plug-ins
). ARD files can also be linked to a graphic using the
.
3D data can be created by using one of these structural design file formats:
• ARD files, created in ArtiosCAD or Studio Toolkit for Boxes
• .ZAE files, created in Studio Toolkit for Flexibles.
• .DAE or .ZAE
Collada files. These can have a printable part (an Esko extension to the
Collada format). Such Collada files can be created in
Studio Designer, Studio Toolkit for
Shrink Sleeves, Studio Toolkit for Labels and ArtiosCAD.
113
67
67.1 Export to 3D Settings
Automation Engine
114
• Export to single output file: When creating a Collada file, select this to create a .zae file instead of a .dae file.
• Scene: A Scene allows to combine multiple task input files into a combined shape. These input files could be
• multiple input PDFs containing the same structural design,
• one input PDF with three pages referring to one part of a Scene,
• multiple input single page PDFs referring to one part of a Scene,
Note: A Scene is a .ZAE file that you can create in Esko ArtiosCAD and Studio Toolkit. It contains links to multiple .ARD or Collada files.
• Output File Type: Choose from these file formats:
• Tiff Image. A 2D image.
• PDF File with 3D Design: Enables to view the 3D in Adobe Reader or Acrobat
Professional (version 8.0.1 or later).
• U3D File: A common exchange format for 3D objects that you can place in Acrobat
Professional (version 8.0.1 or higher).
Automation Engine
67
• Collada file: A common exchange format for 3D objects that can also be viewed in Esko
Studio Viewer and in Esko WebCenter's integrated 3D Viewer.
Settings per File Type:
•
Exporting to Collada
• Choose Collada File as File Type and specify the Resolution of the image(s).
• Define the View Angle from which the object should be rendered. You can either specify them manually here or inherit the angles from the Scene file (using the angle that the file was saved with in Illustrator, Studio or PackEdge).
• Adapt the Perspective. A high value has the effect of a camera with a wide angle lens, close to the object. A low value has the effect of a camera with a zoom lens, further away from the object. The default is 45 degrees.
Note: The object will always fit completely inside the exported image.
• Choose White or Black as Background Color.
• Include Printable Parts: Deselect this to make a 3D that only serves to be viewed. Select it to allow the receiver to edit it, for example to place variant graphics.
•
Exporting to TIFF
• Choose Tiff Image as File Type and specify its Resolution.
• Define the Width / Height of the image. The TIFF image will always be square and will contain the whole shape.
and
• Choose a Background Color: White, Black or Transparent (useful when placing the image in others).
•
Exporting to PDF with 3D Design
• Choose PDF File with 3D Design as File Type and define its Width, Height and
Resolution.
• Show Footer: Select it to add a (custom) Footer Text.
and
• Choose White or Black as Background Color.
•
Exporting to U3D File
• Choose
U3D File as File Type and define its Resolution.
and
• Choose White or Black as Background Color.
115
68
Automation Engine
68. Export to ArtPro File
This task exports a Normalized PDF file to an ArtPro file.
Choose the ArtPro Version:
• an ArtPro 10.x/9.x/8.x file
• an ArtPro 7.5/7.0 file. These do not contain version-specific information or blend modes
(the file will be flattened).
Copy linked files next to output file: Select this to copy the linked images next to the created
ArtPro file.
116
Automation Engine
69
69. Export to EPS/DCS File
The task settings are spread over five tabs:
•
• Color Management: These settings are identical in the
.
•
Rasterize: These settings are identical in the
Rasterize tab of the PostScript Export task
.
• Compression: These settings are identical in the
Compression tab of the PostScript Export task
.
•
Advanced: These settings are identical in the
Advanced tab of the PostScript Export task
69.1 Output
• PostScript version: Choose between 2 or 3.
• Output type:
• EPS. This creates an EPS file with an RGB preview. Select PostScript 3 and deselect color management (in the tab 'Color management') to create a 'deviceN' EPS. In all other cases a CMYK composite EPS will be created.
• Single DCS file. This creates an EPS DCS file with multiple separations. The RGB preview of the DCS file is used when placing the EPS DCS file. In addition, a
grayscale composite
or color CMYK preview can be added for composite printing.
• Multiple DCS file. This creates a master EPS DCS file referring to multiple separations
(one file per ink). The names of the 'Multiple DCS' files consist of the name of the original
EPS DCS file followed by _C, _M, _Y, _K or _1, _2, _3, ... (for all non-process inks). The files have an extension .x.
The RGB preview of the Master DCS file is used when placing the EPS DCS file. In addition, a grayscale composite or color CMYK preview can be added for composite printing.
117
69
Automation Engine
• Preview Resolution: This is the resolution of the RGB preview used when placing the EPS
DCS file. A higher value will produce a finer, more detailed preview but will also increase the files size of the EPS DCS. The default and minimal value is 72 ppi.
• Resolution: If you do not know where the EPS will be placed, you best request a high resolution file (the default is 4.000 ppi.). Mind that, the higher the resolution, the bigger the size of the EPS file will be.
• Page number: Select a page if you only want to export that page of your input file.
• Scale: Allows you to scale the file, for example at 50%.
• Vert. and Hor. Distortion: Use one of these fields if you want a different scaling in either direction (max 90%).
• SmartMarks: If you want to add any, select or define a set.
• Account for job margins: Select this to also include the data between the borders (Trim
Box) and the margins (Media Box).
• Hide trap layer(s) in output: Select this if you do not want those objects in the output file.
118
Automation Engine
70
70. Export to Normalized PDF File
This task converts a GRS file to a Normalized PDF file. GRS is a legacy Esko file format.
External References
External references have to be converted. Choose your preference:
•
Write local external references to the output folder and other external references to
their original folder.
When exporting, external references in subfolders or neighboring folders will be written to the output folder. External references in for example central folders will be written in their original folder.
• Write all external references to the output folder.
• Write all external references to their original folder.
When converting again, you can choose to:
• Reconvert if recently updated: Only updated references will be reconverted, all other conversions will be used as they were.
• Use previous conversions: The existing conversions will be used. Potential updates will not be considered.
• Always reconvert: All external references will be converted at all times.
Embed External Images
Referenced external files in GRS format can be converted to referenced files in Normalized PDF file format. Define which images you want to have converted:
119
70
Automation Engine
1. All images.
2. Images with uncompressed data size smaller than 640 kB (as specified in
Configure
> Processing Preferences > Embedded Images
). This option is identical to the option in the
of the
Normalize PostScript / PDF / Illustrator 8.0 File
3. None.
Copy Other Images to Output Folder
Indicate what should happen with the external images. You can have them copied to the output folder, or you can choose to leave them in their original folder.
Fail when fonts are not found
When the fonts used in the file are not found the task will fail, when the toggle is not selected, the task will end with a warning.
Fail when external references are not found
The task will fail when not all external files were found.
120
Automation Engine
71
71. Export to Normalized PDF File (Embed
All)
You can use this task to create a self-contained version of a Normalized PDF file with references or of a PDFPLA file.
This task embeds all the external references, images and fonts into the Normalized PDF output file.
Note: The
only allows to embed images.
121
72
Automation Engine
72. Export to PDF File
Concept
This task exports Normalized (layout) PDFs to a native PDF. This task is often used to make a
PDF of a specific version or with specific color settings to match the device it will be used for.
This task is also often used to make a self-contained version of a PDF with external references, which makes it easier to exchange this data to someone else.
Factory settings
The Default ticket of this task offers Factory settings. Selecting one is a quick way to define the many ticket parameters. After selecting such a 'preset', you can still change any parameters.
• PDF for data interchange. Use to send this graphic data out.
• (PDF 1.3): Offers high compatibility but slow and less editable. Use this if it needs to be opened in Acrobat 4 or lower, or if a RIP requires this format.
• (PDF 1.4): For interchange with recent applications, well editable. For example Acrobat 5 and higher.
• (PDF 1.5): For interchange with recent applications, well editable. For example Acrobat 6 and higher.
• (PDF 1.6): For interchange with recent applications, well editable. For example Acrobat 7 and higher.
• PDF/X: PDF/X is a standardized subset of PDF designed specifically for reliable interchange of prepress data. It is used for RIP'ing and imposition.
• (PDF/X-1a:2001 (ISO/DIS 15930-1)): PDF/X-1a ensures complete data exchange using
CMYK and spot color data.
• (PDF/X-3:2003 (ISO/DIS 15930-3)): PDF/X-3 ensures complete data exchange suitable for coloured managed workflows.
• PDF for Illustrator CS2 or higher: For a PDF file meant to be edited in Adobe Illustrator
CS2 or higher.
Attention: This version improves the editability in Adobe Illustrator, but does not guarantee full editability.
•
PDF for viewing/proofing
• CMYK Composite: Useful when using hard copy proofers, or when the result doesn't have to be editable or when the result is used for soft-proofing. It is not useful to serve as final output.
• RGB: Useful for soft-proofing ; a smaller file, and faster to generate.
• DeviceN: Data interchange file for proofing/viewing (all separations present). Adobe
Acrobat Reader 7.0 or later is required to view the overprint settings correctly.
122
Automation Engine
72
Note: Even though, for trapping reasons, Acrobat 7 Professional and higher allow to define an ink as Opaque ("Ink Manager"), this has no influence on the PDF preview.
Detailed settings
The many ticket parameters are divided over seven tabs:
•
•
on page 126
•
on page 126
•
tab Inks/Separations in the "Export to PostScript" task
.
• Rasterize, similar to the
tab Rasterize in the "Export to PostScript" task
.
•
•
on page 129.
72.1 Output
• PDF Version:
• PDF 1.6: The Acrobat 7 file format.
• PDF 1.5: The Acrobat 6 file format.
• PDF 1.4: The Acrobat 5 file format.
• PDF 1.3: The Acrobat 4 file format.
• PDF for Illustrator: Select this if the generated PDF 1.4 file will be opened in Adobe
Illustrator CS2 or higher. Because Adobe Illustrator only supports an (undocumented) subset of PDF 1.4 features, some objects and/or color-spaces will be split up, transformed and/or pre-ripped in order to correctly represent them in Illustrator.
123
72
Automation Engine
• PDF/X-1a:2001 (ISO/DIS 15930-1) and PDF/X-3:2003 (ISO/DIS 15930-3). Learn more
.
• Password security: Learn more in
on page 124.
•
Output type
• Composite: Select this to create a composite file which, if no color management is used, produces a 'DeviceN' PDF for data interchange. DeviceN means that its colors can be combinations of the standard CMYK process colors and/or spot colors. This guarantees perfectly separable PDF files which can also be proofed on a composite PostScript 3 device. Such a PDF file will both proof and separate correctly. Color management for spot color objects must then be handled by the device.
• Separated: Select this to create a PDF with multiple pages, one page per ink.
• Emulsion Up: Select Right Reading (= emulsion up) or Wrong Reading (= emulsion down).
• Image: Select Positive or Negative print mode.
• Vert. and Hor. Distortion: Use one of these fields if you want a different scaling in either direction (max 90%).
• Scale: Allows you to scale the file, for example at 50% to get a smaller MB size when Emailing the PDF.
• SmartMarks: Add SmartMarks if you want, for example to add the ink coverage on a proof
PDF.
• Account for job margins: Select this to also include the data between the borders (Trim
Box) and the margins (Media Box).
• Hide trap layer(s) in output: Select this if you do not want those objects in the output file.
• Page Range: When your input file has multiple pages, define here if you want All or a selection of these pages in your output PDF file.
72.1.1 Password Security
Note: The options in this dialog depend on the PDF version that you chose in the
Output tab of the 'Export to PDF' task)
124
Automation Engine
72
•
Compatibility: The security features depends on the Acrobat version that you want to output. Your choice defines the
Encryption level.
•
Require a password to open the document: If this is what you want, enter a password.
Communicate this password to the people that you allow to open this file.
•
Permissions (some options depend on the selected Compatibility):
• Use a password to restrict permissions: If you want to use any of the below options, enter a specific Permissions Password and communicate it to the right people.
• Printing Allowed: Select None if no-one is allowed to print this file. Select a Resolution if the receiver may print it at that level of quality.
• Changes allowed:
• Select
None to prevent users from making any changes, not even filling in signature or form fields.
• Select
Inserting, deleting and rotating to allow such changes, as well as create bookmarks and thumbnail pages.
• Select
Any except extracting pages to allow users any changes except extracting pages.
• Select
Enable copying of content to allow the user to do this.
• Select
Enable text Access to allow visually impaired users to read the file with screen readers. This option does not allow users to copy or extract any contents.
•
Enable plaintext metadata: This allows searching the file's properties while still protecting its content.
125
72
Automation Engine
72.2 Device
You can make a PDF 'device specific' by adding a description of the required
dot gain
compensation curves inside that PDF.
Attention: These curves are not calculated, but stored as 'PDF standard transfer curves'. Opening the PDF in Acrobat will not show any difference.
You can create
Dot Gain Compensation curves (DGC) with Esko Curve Pilot.
• Single Curve: Select one DGC curve (.dgc file) that will be applied to all your data.
• Automatic: Allows you to select one of these types:
• A Screen-Based DGC table (.scrdgc file), to apply dot gain compensation selectively, depending on the dot shape, screen ruling, angles and even Contone or Linework properties.
• A DGC Strategy (.icpro file), does the same but also offers ink-based dot gain compensation.
Note: You can also apply both a single curve and an automatic DGC. This then results in a cumulation of both effects.
72.3 Color Management
126
When you choose not to apply any color management when creating the PDF, you can still
.
When creating a
, you can choose to Use Color Management with these options:
• Convert to: Select to which color space all inks should be converted: CMYK, RGB or Gray values.
• Use Link Profile: "Link profiles" describe a transformation from one device-dependent color space to another. This is actually a concatenation of a forward transformation of one
Automation Engine
72 profile and a backward transformation of another profile. A link profile takes complete care of the color management, so all other options are then disabled.
• Source profile: If any CMYK objects need to be converted, choose a 'source profile'. The list shows all CMYK print profiles in the color database. The source profile defines the target that the destination profile is supposed to match.
• Destination profile: Choose a color profile for your destination color space. The list shows all print profiles in the color database. These profiles are either measured in Color Engine
Pilot or imported ICC-profiles.
•
Rendering intent
• Relative (no background): Choose this if you do not want any background simulation.
The white point of the source will be mapped on the white point of the destination process. This rendering intent takes into account the ability of the human eye to adapt to the surrounding white.
• Absolute (background): Choose this if you want background simulation and you want an exact color match, including the paper simulation.
• Perceptual: This will result in no background simulation (white of reference color space is mapped on white of destination color space). Choose this when you don't care too much about an exact color match but when want the pictures at least to look nice on your proofer. It will give a visually pleasing result. If the gamut of the source is wider than the proofer, the entire gamut is shrunk so that it fits inside the gamut of the proofer.
• Saturation: Choose this if you care especially about saturated colors. This rendering intent will map saturated colors on saturated colors.
• Black Mapping:
• When selected, the CMY part of the composite colors are converted separately from the black component. As a result, the type of black separation (Skeleton black, UCR, GCR...) is preserved by the conversion. It is still possible that the black percentage changes slightly due to different dot gain in the color profiles.
• When not selected, the converted CMYK colors are completely re-separated into the black behavior that is built into the destination profile.
• Use the document profile as Source profile if available: If a document profile is defined, then that one will be used as a source profile. The one chosen from the above
Source
Profile list will be overruled.
• Embed the Destination profile as an intermediate color space:
• When not selected, the colors in the PDF file are not tagged with an ICC color profile. The document is device dependent and its colors will only be reproduced accurately if the
PDF file is output on the device that is specified in the Destination Profile. This choice is preferable when you are sure the PDF file will be sent to the device specified in the
Destination Profile.
• When selected, the colors in the PDF file are tagged with an ICC color profile. The document then becomes device independent, and its colors will be reproduced accurately even on devices with a color space different from the one specified in the
Destination Profile. In this case, the Destination Profile is an intermediate color space between the Source Profile and the color profile of the device that will eventually process the PDF file. This choice is preferable when the PDF file will be sent to an unknown device.
127
72
Automation Engine
Embed the document profile as PDF Output intent: The output intent is an ICC profile that specifies the intended output device. When selected, the document profile will be saved as the
'PDF Output Intent'. For some PDF flavors (PDF-X/3), an output intent is mandatory and this option is always on.
When no document profile was set explicitly, the default document profile is used instead
(crom_offs). When the document profile is a Color Engine Pilot profile, it will first be converted to an ICC profile.
72.4 Compression
128
General
• Optimized lossless image compression: Selecting an overall lossless image compression seldom results in the smallest overall file size. This optimization chooses the smallest lossless compression method for every image separately (JPEG2000, Flate, FlateDiff, LZW,
LZWDiff, CCITT3, CCITT4 or Run Length). Its choice depends on the image type and on the compression methods that are allowed for the chosen PDF version.
Selecting this option disables the compression methods for Bitmaps and Contones. It also sets the encoding to Binary, which we advise to keep, otherwise the resulting file will become larger.
Attention: Selecting this option considerably slows down this task, so only use it when the size of the file is critical.
• Crop images on clip mask: When selected, all information outside the clip mask will not be exported.
•
Encoding
• Binary: The image data is represented as binary data. This results in compact files. Such files are not editable in a common ASCII editor. Nor can these files be transferred using a communication protocol that relies on control characters in the data stream itself.
• Hex: This forces the output to remain editable with an ASCII editor. It can then also can be transferred using whatever communication protocol is available. The drawback is that hexadecimal image data can take up to twice as much size as binary data.
•
ASCII 85: Encodes binary data in an ASCII base-85 representation. This encoding uses nearly all of the printable ASCII characters. The resulting expansion factor is 4:5, making this encoding more efficient than hexadecimal.
Automation Engine
72
Bitmaps
• Downsample: Referenced images are sub-sampled approximately to the specified value. This reduces the size of the output PDF file. The unit is the one defined in Edit >
Preferences . Be aware that 1–bit (copydot) images cannot be downsampled.
• Compression: Choose the type: None or CCITT group 3 / 4, Run Length, LZW (Diff), Flate
(ZIP) (Diff).
Contones
• Downsample: The images referenced in your design are sub-sampled to approximately the specified value. This allows to reduce the size of the generated PDF file. The unit is the one defined in Edit > Preferences .
• Compression: Choose the type: None or LZW (Diff), JPEG(2000), Flate (ZIP) (Diff).
JPEG compressions allow to specify the quality of the compression..
Text and Lineart
• Compression: Choose the type: None or LZW or Flate (ZIP).
72.5 Advanced
Fonts
Choose what to do with the fonts used by your input file's live text:
• Contourize fonts: To convert all text into lineart.
•
Embed BG and Type1 and CID fonts
Note: Protected CID fonts will be referenced by name.
Split Complex Paths: When a device requires that you create an old version of PDF (1.3), it may also require that you split very complex paths into smaller ones.
Note: These are workarounds for typical PostScript level 1 path limitations. Only use these when absolutely necessary.
129
72
Automation Engine
• Filled and stroked paths at: Use this option to split linework with more than x points into several smaller linework parts. This decreases the complexity of the linework. A suitable value for the selected Device type is calculated automatically.
• Clip paths at: Use this option to split linework masks for images with more than x points into several smaller linework parts. This decreases the complexity of the masks.
Workaround
• Limit file name to 31 characters: Select this when the system that will read your output file is limited to 31 characters.
• Ignore varnish inks: Select this to exclude varnish inks in your output.
• Resolve pure black overprint: Overprints are normally resolved, but by default, pure black is left untouched. Select this option when you also want pure black to be resolved. This option is only available when
• Resolve once identical external files: Instead of resolving the complete file and all its external references, identical external files will be resolved only once.
• Resolve once identical one-ups in Step & Repeat file: Instead of resolving the complete
Step & Repeat file, identical one-ups will be resolved only once.
• Suffix for PANTONE ink names: Enter a suffix for PANTONE ink names. The default is 'C'.
For example: PANTONE 123 so becomes PANTONE 123 C . Existing suffixes will be replaced by this one.
• Split multi page job into multiple files: Every page of a multi page file will be output as a separate PDF file.
• Add Ruling, Angle and Dot Shape information in PDF Data section: Select this if the non-
Esko RIP that will read the PDF will want to get such screening information from inside the
PDF itself. This makes the PDF device-dependant.
• Add Ink Coverage data in XMP: Select this to add such data into the PDF's metadata. Mind that calculating the ink coverage will slow down the task.
130
Automation Engine
73
73. Export to PostScript File
Factory settings
The Default ticket of this task offers Factory settings. Selecting one is a quick way to define the many ticket parameters. After selecting such a 'preset', you can still change any parameters.
•
PostScript for press (separated)
• PostScript for press (DeviceN composite): This mode (only supported by PostScript 3 devices) uses the PostScript 'DeviceN' color-space to produce high-fidelity colors. These colors are combinations of the standard CMYK process colorants and/or spot colors, guaranteeing perfectly separable PostScript code that can be proofed on a composite
PostScript 3 device.
•
PostScript for viewing / proofing (CMYK composite)
73.1 Output
Device type: The selected device type also determines the PPD that will be used.
Output type:
• Separated: Select this to generate multiple pages, one for each ink in the file.
• CMYK Composite: Select this to generate a composite PostScript file, typically for proofing.
All spot colors are converted to CMYK.
• Composite: Select this to generate a file for PostScript 3 devices, since they support
'deviceN' color-space to produce high-fidelity colors. These colors are combinations of the standard CMYK process colors and/or spot colors, guaranteeing perfectly separable
PostScript code which can also be proofed on a composite PostScript 3 device.
The generated PostScript file will proof correctly and separate correctly. Color management for spot color objects must be handled by the device.
131
73
Automation Engine
Emulsion Up: Select Right Reading (= emulsion up) or Wrong Reading (= emulsion down).
Image: Select Positive or Negative print mode.
Enter a Vertical and/or Horizontal distortion in percentages (between 90 and 110 %).
Add SmartMarks if you want.
Account for job margins: Select this to also include the data between the borders (Trim Box) and the margins (Media Box).
Hide trap layer(s) in output: Select this if you do not want those objects in the output file.
Page Setup
• Select a Paper size. The list is based on the page sizes supported by the selected .PPD.
• Orientation: (Disabled when 'Tile job' is selected.)
• Alignment: (Disabled when 'Tile job' is selected.)
• Enter the Number of copies.
Scale & Tile
• Enter a Scale factor (percentage).
• Fit job on page scales the file so it fits the selected paper size.
• Shrink oversized jobs to paper size.
• Select ' Tile job' to obtain a tiled output if the file is too big to fit on the selected Paper
size. It then exports a large file to a series of smaller pages (tiles). The user can then cycle through the tiles, and see how many tiles there are.
Overlap: The value you enter here is the amount of overlap in all four directions between adjacent tiles.
Page Range: When your input file has multiple pages, define here if you want All or a selection of these pages in your output PDF file.
73.2 Device
Most of these options depend on the PPD belonging to the selected
132
Resolution: Select one that fits the purpose of the PostScript file.
Automation Engine
73
Dot Shape: Define if you want a specific dot for this file.
Halftoning: When the
is 'CMYK Composite' or 'Composite', you can choose to
include screen information (LPI and angle).
• Use Printer Defaults: From the output device.
• Take over from job: From the input file.
• Some PPDs offer other dot shapes.
Dot Gain Compensation: Select a Single and/or Automatic curves (made in Curve Pilot). This will be added as 'transfer curve'. Learn more
Note: When a DGC curve is selected, the file will be flattened to ensure that the correct Dot
Gain Compensation is applied to transparent objects. This may result in a larger file.
Roll fed devices:
• Account for Media Width allows the task to find the best printing orientation (when
Rotation is set to Auto). For roll-fed devices, mostly film-setters, a media width (film width) can be specified.
• Extra Gap: Allows you to specify extra width for the film or paper feed.
Device specific options: These depend on the selected PPD. Learn more in the documentation of your output device.
73.3 Color Management
These options are enabled when you choose the
.
Convert to:
• Choose to convert all inks to CMYK or Gray values.
• Use Link Profile: "Link profiles" describe a transformation from one device-dependent color space to another. This is actually a concatenation of a forward transformation of one profile and a backward transformation of another profile. A link profile takes complete care of the color management, so all other options are then disabled.
Source profile: If any CMYK objects need to be converted, choose a 'source profile'. The list shows all CMYK print profiles in the color database. The source profile defines the target that the destination profile is supposed to match.
Destination profile: Choose a color profile for your destination color space. The list shows all print profiles in the color database. These profiles are either measured in Color Engine Pilot or imported ICC-profiles.
133
73
Automation Engine
Rendering intent
• Relative (no background): Choose this if you do not want any background simulation. The white point of the source will be mapped on the white point of the destination process. This rendering intent takes into account the ability of the human eye to adapt to the surrounding white.
• Absolute (background): Choose this if you want background simulation and you want an exact color match, including the paper simulation.
Black Mapping:
• When selected, the CMY part of the composite colors are converted separately from the black component. As a result, the type of black separation (Skeleton black, UCR, GCR...) is preserved by the conversion. It is still possible that the black percentage changes slightly due to different dot gain in the color profiles.
• When not selected, the converted CMYK colors are completely re-separated into the black behavior that is built into the destination profile.
Use the document profile as Source profile if available: If a document profile is defined, then that one will be used as a source profile. The one chosen from the above
Source Profile
list will be overruled.
73.4 Inks / Separations
The name of this tab depends on the output type you selected in the
• If you there choose CMYK Composite or Composite, the Inks tab appears:
134
• If you there choose Separated output, the Separations tab appears.
Automation Engine
73
All Inks: Deselect this to open an ink-list panel where you can select specific inks.
Note: The Inks panel only shows the inks that are present in the input file(s) for the first task in your workflow. When no input files are selected yet, you will not be able to “preselect” inks
(for example when building workflows in the Tickets view).
Use technical inks in output: Select this option to also output the (non hidden) technical inks.
Convert all inks to CMYK:
In the Inks panel, use Merge Ink With to output inks on top of each other in the same output file. The ticket proposes this automatically when you have different rulings for 1 ink. You can set this manually by clicking in the Merge with column and selecting the ink it has to be merged with.
73.5 Rasterize
Rasterisation resolution: Enter the resolution for the objects that will be 'resolved' (converted to image data).
Output as image: Select this to make an image of the input file (with the above set resolution).
Anti-aliasing: This smoothens the staircase effect in images generated from line-art objects that were pre-processed. This increases the readability of small text that is converted to image data.
135
73
Automation Engine
Convert vignettes to image: Select this to avoid blends and banding in vignettes when exporting to PostScript. This converts all vignettes to images.
Vignette noise: When exporting to PostScript, some (parts of) vignettes will be converted to images. This happens when the vignettes overlap other objects with translucency or when there are overprints between a vignette and other objects.
When 'Convert vignettes to image' is selected, all vignettes are converted to images regardless of any overlap with other objects. Vignettes that are converted to images may have tone jumps in the final result. To reduce this banding effect, noise is applied on the image. Define the amount of noise in this field.
73.6 Compression
Encoding:
• Binary: The image data is represented as binary data. This results in compact files. Such files are not editable in a common ASCII editor. Nor can these files be transferred using a communication protocol that relies on control characters in the data stream itself.
• Hex: This forces the output to remain editable with an ASCII editor. It can then also can be transferred using whatever communication protocol is available. The drawback is that hexadecimal image data can take up to twice as much size as binary data.
• ASCII 85: Encodes binary data in an ASCII base-85 representation. This encoding uses nearly all of the printable ASCII characters. The resulting expansion factor is 4:5, making this encoding more efficient than hexadecimal.
Compression: Choose None, LZW or Flate (PostScript 3 devices).
Downsampling: Use this to downsample the images referenced in the file to (approximately) the specified value. This will result in a smaller PostScript file. It will also be generated faster.
Please be aware that 1–bit copydot images cannot be downsampled.
73.7 Advanced
Split Complex Paths
When a device requires that you create an old version of PostScript (level 1), it may also require that you split very complex paths into smaller ones.
• Filled and stroked paths at: Use this option to split linework with more than x points into several smaller linework parts. This decreases the complexity of the linework. A suitable value for the selected Device type is calculated automatically.
136
Automation Engine
73
• Clip paths at: Use this option to split linework masks for images with more than x points into several smaller linework parts. This decreases the complexity of the masks.
Workaround
• Limit file name to 31 characters: Select this when the system that will read your output file is limited to 31 characters.
• Ignore varnish inks: Select this to exclude varnish inks in your output.
• Resolve pure black overprint: Overprints are normally resolved, but by default, pure black is left untouched. Select this option when you also want pure black to be resolved.
This option is only available when you selected 'CMYK composite' as 'Output' tab.
• Resolve once identical external files: Instead of resolving the complete file and all its external references, identical external files will be resolved only once.
• Resolve once identical one-ups in Step & Repeat file: Instead of resolving the complete
Step & Repeat file, identical one-ups will be resolved only once.
• Suffix for PANTONE ink names: Enter a suffix for PANTONE ink names. The default is 'C'.
For example: PANTONE 123 so becomes PANTONE 123 C . Existing suffixes will be replaced by this one.
• Suppress hairlines at clips : Due to the PostScript limitation of the maximum number of points allowed for a path, complex paths will be cut into smaller pieces. When the PostScript file is used for an old PostScript RIP, 'hairlines' can so become visible. To avoid this problem, select this option.
• Split multi page job into multiple files: Every page of a multi page file will be output as a separate PS file.
• Image to paper edge: This moves the origin of output file to the lower left corner of the paper or film. Select this option to align your file to the edge of the paper or film to use the full area.
Note: When exporting to a paper PostScript device, there is typically a border on the output page on which nothing can be imaged. Parts of your design that are located in that border area will be lost.
• Avoid tabular number problem: When digits are written as tabular numbers, exporting to some PostScript RIPs may result in bad positioning of the numbers. Select this to avoid that tabular numbers are not correctly placed at the text base line.
• Disable path clipping: Select this if you do not want paths to be clipped on the
'borders' (Trim Box) of the file.
• Map spot color separations to CMYK: Select this when you export a file containing spot colors to pre-separated PostScript for systems that are limited to separations of process colors (for example a Scitex Brisque workflow).
Spot color separations can only be handled on such systems by mapping them to a specific process separation (not converting, just mapping). Spot colors are then exported as a C, M,
Y or K separation according to a simple rotating name principle (C->M->Y->K->C->M...).
Spot colors which are named exactly after process colors remain unchanged.
137
73
Automation Engine
• Omit “Process” for CMYK in %% PlateColor comment: Select this when the file will be sent to a device that does not understand "Process".
You must select this option when outputting to an Image Setter and when your different separations all have the Angle and Rulings of the K separation (Black).
• Split separated output into multiple files: Instead of writing one file containing all separations, the task will write one file per separation.
• Force Black Overprint: Select this if you want all 100% black objects to overprint in your
PostScript file.
138
Automation Engine
74
74. Extract Inks
Concept
This task writes a PDF that only contains the inks that you here decided to keep, by defining their Name or on their Printing Method.
The resulting PDF will look the same as if you opened the input file in the Automation Engine
Viewer and there made the same selection of inks.
This task is typically used to build (parts of) workflows that you only want to execute on specific inks. This is especially useful when the PDF will be output on a hybrid press. For example: a workflow that automatically sends the 'Flexo' inks to a different RIP than the 'Screen' inks.
Note: Learn more about such a workflow in the dedicated section about
Hybrid Press Workflow
.
Another example where this task is useful is when you want to generate separate file reports per 'group' of inks.
Task Settings
You define which inks you want to keep, based on their Name or on their Printing method.
Click on to select one or multiple printing methods (a list defined in the
Configure tool
).
Click + if you want to add extra criteria. Click Alt and then ... button to add sub-criteria.
Learn more on how to add such criteria in the page that describes how to make
(smart) filters in the Pilot
.
Some examples:
• Only keeping the inks with the Printing method 'Flexo':
• Only keeping the inks that do not have the Printing method 'Flexo':
139
74
Automation Engine
• Keeping the Flexo Pantone inks and/or inks which name contains 'cut' or 'crease':
140
Automation Engine
75
75. Fork
This Workflow Control is documented in the chapter
Workflows
. See
Fork and Join
.
141
76
Automation Engine
76. Image to Screened Separations
This task is documented in the chapter on
Imaging Engine
. Find a direct link
here
.
142
Automation Engine
77
77. Image to Unscreened Separations
This task is documented in the chapter on
Imaging Engine
. Find a direct link
here
.
143
78
Automation Engine
78. Import Image
The task converts pixel images to the Esko CT or LP file format.
You can also use it to convert RGB images to CMYK, probably for easier processing in the workflow.
You can also use prit to convert CMYK CTs with Inkswitch or BlackSmith.
144
Mask/Path Settings
• Select Keep Pixel Masks to keep the original pixel mask in the output image.
• Select Keep Clipping Path to keep the original clipping path.
Preview Settings
• Create Thumbnail. Small RGB image used in an 'Info' panel in the Pilot or in the "File-Open" dialogs of Esko editors.
• Create Preview. Only used in PackEdge's low-quality view mode.
Keep Indexed
If the colors in the image are reduced ("indexed"), select this if you want to keep that in the output image.
RGB Conversion Method
There are two ways to convert RGB data to CMYK:
•
Device Link Profile
This allows you to select a Process Link, made in
Color Engine Pilot
. This option will give you the best result.
"Link profiles" describe a transformation from one device-dependent color space to another. This is actually a concatenation of a forward transformation of one profile and a backward transformation of another profile. A link profile takes complete care of the color management, so all other options are then disabled.
•
Device Profile
This enables you to select a source and a destination (proofer) process. Use this option if you did not make a Process Link in Color Engine Pilot but you still want a better color result.
The process links will be made for you.
Automation Engine
78
RGB Profile: Source profile used for conversion.
CMYK Profile: Destination profile used for conversion.
Rendering Intent:
• Relative (no background): Choose this if you do not want any background simulation.
The white point of the source will be mapped on the white point of the destination process. This rendering intent takes into account the ability of the human eye to adapt to the surrounding white.
• Absolute (background): Choose this if you want background simulation and you want an exact color match, including the paper simulation.
• Perceptual: This will result in no background simulation (white of reference color space is mapped on white of destination color space). Choose this when you don't care too much about an exact color match but when want the pictures at least to look nice on your proofer. It will give a visually pleasing result. If the gamut of the source is wider than the proofer, the entire gamut is shrunk so that it fits inside the gamut of the proofer.
• Saturation: Choose this if you care especially about saturated colors. This rendering intent will map saturated colors on saturated colors.
Note: For BGCMS profiles, Perceptual, Relative and Saturation are in fact identical.
CMYK Conversion
Choose the conversion Method and its Profile.
Learn more about these conversions in
the documentation of Color Engine Pilot
.
145
79
Automation Engine
79. Import JDF Layout
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
146
Automation Engine
80
80. Import JDF Step & Repeat
This task creates a Step & Repeat (PDFPLA) file based on a JDF file.
• When the JDF file contains a link to PDF 'station' files, the task performs a tabular Step &
Repeat.
• When the JDF file contains a link to a CAD file and to its PDF 'station' files, the task performs a CAD-based Step & Repeat.
Note: The JDF should always contain a list of the input files.
General
• Output Format: Choose the type of PDF you want to create.
• SmartMarks. If you wish, select or define a set of SmartMarks.
• Load Mark Set in bottom layer: Select this if you want to make sure the marks are
"behind" the graphics.
• Limit Bleed to: The bleed mask is created by spreading the die shape. Use this option to limit that bleed to a specific distance.
Plate Setup
• Use Sheet Size from JDF: You can either use the sheet size defined in the JDF, or define one yourself (in which case you need to choose the Unit).
• Use Plate Size from JDF: You can either use the plate size defined in the JDF, or define one yourself, in which case you also need to define the Sheet Offset and the Sheet Position on
Plate.
Sheet Offset: Define by how much the sheet should be offset from the plate corner, horizontally and vertically.
Sheet Position on Plate: Click the blue rectangle (sheet) to position it on the gray one
(plate) .
Note: Take into account the point of Origin from which the repetition will be built. This is defined in the JDF and is always bottom left.
Shrink: Enter a horizontal or vertical value to compensate for printing distortion (especially in Flexo).
Screen Registration: Select this when you need each station of the Step & Repeat to have the exact same screening, for example when printing postage stamps. This forces the screening to 'start again' for each 'station'.
Attention: This option defines an attribute in the PDF that is only supported by
Imaging Engine or FlexRip. It is ignored by any other RIP..
CAD Options
147
80
Automation Engine
• Mapping: When the CAD file is a CFF2 or DXF file, you here select the set of mapping rules.
These rules map line styles (cut, crease, bleed), layer names and color numbers onto
ArtiosCAD line types. These sets of mapping rules can be created in Esko PackEdge or Plato.
Learn more in the user documentation of these editors, more specifically in their section on placing files (PackEdge) or on importing CAD data (Plato).
• The CAD Style changes the appearance of the (imported) ArtiosCAD type lines. The styles you can select here were also created in PackEdge or Plato. Learn more in the their user documentation, more specifically in the section on placing ArtiosCAD files, and the option for "CAD Style".
• Include CAD info for Digital Flexo Suite:
If you are using the Esko
Digital Flexo Suite
(DFS), select this option to add the technical inks data into the header of the output file (this is usually the cut and crease lines). This data is then visible in the Esko Bitmap Viewer and also embedded in the LEN files created by an
Esko RIP.
The DFS can export this information into ACM files for an Esko Kongsberg cutting table. In
Esko PlatePatcher workflows, this information can be used to print onto the plastic sheet where the pieces of flexo plate are re-assembled. These technical lines can also represent text that is then added onto the (back of the) flexo plates, using a pen on the Kongsberg table.
Attention: This feature is ignored when you choose the output format (native) PDF.
• Use Blank Position from JDF: You can either use the blank position defined in your JDF ticket, or position the blank on the sheet yourself.
Note: The blank represents the one-up design without the artwork (i.e. the bounding box of the one-up).
Position Blank on Sheet: Click the small blue rectangle (the blank) to the right position on the big gray rectangle (the sheet).
Note: Take into account the point of Origin from which the repetition will be built. This is defined in the JDF and is always bottom left.
Blank to Sheet Offset: Define by how much the blank should be offset from the sheet corner, horizontally and vertically.
148
Automation Engine
81
81. Import JDF Stripping
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
149
82
Automation Engine
82. Import Substrate Sizes from XML
This task is documented in the separate chapter
Gang Run Printing for Sign & Display
. Find a direct link
here
.
150
Automation Engine
83
83. Inspect Artwork
This task is documented in the separate chapter
Quality Control tools
. Find a direct link
here
.
151
84
Automation Engine
84. Inspect Barcodes
This task is documented in the separate chapter
Quality Control tools
. Find a direct link
here
.
152
Automation Engine
85
85. Inspect Braille
This task is documented in the separate chapter
Quality Control tools
. Find a direct link
here
.
153
86
Automation Engine
86. Inspect Spelling
This task is documented in the separate chapter
Quality Control tools
. Find a direct link
here
.
154
Automation Engine
87
87. Inspect Text
This task is documented in the separate chapter
Quality Control tools
. Find a direct link
here
.
155
88
Automation Engine
88. Integrate via External Hot Folder
This task allows to integrate external (prepress) applications into your workflow. The only requirement is that the external application works with hot folders.
1. In the ticket, you define the location of the hot folder used by the external application, as well as the Result subfolders in which the external application will output processed files (the OK Folder), failed files (Error Folder) or files that resulted in warnings (Warnings
Folder).
Attention: You need to define a different folder for each output state. This can not be the same folder.
2. When you select a file and launch this task, the task first copies the file to the external hot
folder.
3. The external application picks up the files in its hot folder and processes them. The processed files are saved in the subfolder that matches the processing result: OK, Warning or Error.
4. Automation Engine monitors the OK, Warning and Error folders for any files that have been processed.
Important: As mentioned above, these have to be three different folders.
5. When Automation Engine detects a file in the OK folder, it copies it to the Output folder defined in this ticket. Depending on your settings, Error or Warning files might also be copied into the Output folder, or they might be deleted.
156
Automation Engine
88
In the Error area of the ticket, you can define an amount of time after which the external processing should automatically be considered as failed. To do this, enable the option "Error
when no result after" and select a time period.
157
89
Automation Engine
89. Integrate with WebCenter
This task is documented in the chapter Integrating with WebCenter. Find a direct link
here
.
158
Automation Engine
90
90. Interact with Database
This task is documented in the chapter Integrating with External Systems. Find a direct link
here
.
159
91
Automation Engine
91. Interact with SAP
This task is mentioned in the chapter
Integrating with External Systems
. Find a direct link
here
.
160
Automation Engine
92
92. Interact with Web Service
This task is documented in the chapter Integrating with External Systems. Find a direct link
here
.
161
93
Automation Engine
93. Join
This Workflow Control is documented in the chapter "Workflows". See
Fork and Join
.
162
Automation Engine
94
94. Join XML Files
This task is documented in the chapter Integrating with External Systems. Find a direct link
here
.
163
95
95. Link Product To Job
This task is documented in the chapter
Products
. Find a direct link
here
.
Automation Engine
164
Automation Engine
96
96. Load Structural File
Concept
This task loads a structural design file into a graphics file.
The structural file is loaded in a dedicated new layer named Structure_[name of structural file]. The structural file is put in a technical ink (as defined in the CAD Style, see below).
Tip: The result file can be used as an input file for the
task.
Note: The task ends with an error when an input normalized PDF file already contains a structural file (one that was loaded in PackEdge, ArtPro, DeskPack or by an Automation Engine task).
Supported Types of Structural Design Files
This task can load these types of structural files:
• CAD files: ARD, CF2, DXF files. For CF2 or DXF files, you have to indicate a Mapping file to map their file attributes onto ArtiosCAD-like line types (to become cut, crease or bleed lines or to be ignored). The CAD Style file is needed to define their appearance, for example the color they get. Mappings and CAD styles can be defined in Esko editors.
• Collada files: DAE, ZAE file. These files need to have a printable area. When the file has multiple printable areas, the area that matches the size of the selected page box gets selected. When the file has no or multiple matching printable areas are found, the task ends with an error.
• Esko Flexible file: BAG file. This file type was created before ZAE was supported.
Positioning
The structural object will be positioned in the center of the selected page box (
Media, Crop,
Trim, Bleed, Art Box).
The task ends with a warning when the dimensions (bounding box) of the structural file do not match the size of the selected page box.
Important: The structural file is not rotated.
165
96
Optionally, you can fit the trim box to the structural design.
Automation Engine
166
Automation Engine
97
97. Manage Color
With this task, you can:
• convert a CMYK file to another CMYK profile,
• re-separate a CMYK file so that it contains less CMY and more K, while keeping the image looking the same,
• both convert and re-separate your CMYK file.
This task takes PDF and Normalized PDF files as input. When working with regular PDFs, it will automatically normalize them using the Normalize ticket set in the Configure tool (see
Processing Preferences
).
97.1 Converting to another CMYK Profile
You can convert a file to another CMYK profile if for example you want to print it on a different substrate, on a different press, or even with a different printing process (offset, digital printing...).
In Actions, select Convert color space to convert your input file to another CMYK profile. This displays extra parameters below it.
1. Choose what to use as a source profile when converting your input file: a) In Source CMYK Profile, select the source profile to use for the conversion in case you are not using your input file's profile.
This can be an Esko or an ICC profile and you can use a SmartName (resolving to the full profile name) to set it. By default this is ISOcoated_v2_eci.icc.
b) If your input file has a CMYK profile and you want to use it for the conversion, select
Use
document profile if available.
When processing a file without a profile, the task will use the Source CMYK Profile you selected.
2. Choose what Destination CMYK Profile to convert your file to.
This can be an Esko or an ICC profile and you can use a SmartName (resolving to the full profile name) to set it. By default this is ISOcoated_v2_eci.icc.
3. Choose the Rendering Intent to use when converting the colors.
A Rendering Intent is a part of the color strategy that handles the conversion of out-ofgamut spot colors and of the background color.
Each of the four rendering intents available does this in a different way, so you should choose the one that is more adapted to the way you are printing and the result you want to achieve:
• Use the Relative Colorimetric rendering intent if you don't want to simulate the source background (the point that has 0% of all inks in the source profile).
This will proof your file as if the proofer substrate was exactly the same as the substrate defined in your source profile.
167
97
Automation Engine
For example: your press prints on cream colored card stock whereas your proofer prints on bright white paper, but you don't want to simulate the cream background on your proof.
168
With this rendering intent, colors from the source profile that cannot be reproduced by the proofer will be converted to the closest color(s) the proofer can reproduce.
In some cases several colors will be converted to the same color, which means that you can sometime lose some detail, especially in dark saturated areas and the dark parts of gradations.
Note that typically the proofer profile has a bigger gamut than the press profile, so there are not many colors that the proofer cannot reproduce.
• Use the Absolute Colorimetric rendering intent if you want to simulate the source background to get as exact a color match as possible.
For example: you do want to simulate the cream colored card stock used on your press on your proofer substrate, to see how the final output will look like.
Automation Engine
97
As with the Relative Colorimetric rendering intent, colors from the source profile that cannot be reproduced by the proofer will be converted to the closest color(s) the proofer can reproduce, meaning you can sometime lose some detail, although there are typically not many press colors that a proofer cannot reproduce.
• Use the Perceptual rendering intent if you are not trying to get an exact color match but want the proof to look visually pleasing.
If there are colors from the source profile that cannot be reproduced by the proofer, this will shrink the source gamut to fit inside the gamut of the proofer, so that all colors are converted (even the colors already in the proofer's gamut), but the relationship between colors is kept.
This means that colors won't be really accurate, but you won't lose detail in dark saturated areas or gradations.
This rendering intent is most commonly used in commercial printing (for newspapers, magazines, posters...).
• Use the Saturation rendering intent if you mostly want to make sure the colors on your proof are saturated enough.
169
97
Automation Engine
Colors from the source profile that cannot be reproduced by the proofer will be mapped onto close saturated colors that are in the proofer's gamut.
This rendering intent is most commonly used for business presentations containing graphics, or cartoons/comics.
Note: You can only use a Perceptual or Saturation rendering intent if you are working with ICC source and destination profiles.
You can also set the rendering intent with a SmartName, resolving to 2 (for Perceptual), 3
(for Relative Colorimetric), 4 (for Saturation) or 5 (for Absolute Colorimetric).
4. If you cannot reproduce the same range of black on output, select Use black point
compensation to avoid losing some detail in the shadow areas.
This can be the case for example if you originally printed a job on coated paper, but now need to print it on uncoated (as the uncoated paper will absorb more of the ink and give less of a sharp, saturated result).
Coated
Uncoated
Without black point compensation, some of the details in the darkest areas can get lost.
170
Black point compensation shrinks the whole black range proportionally, so that both the shadows details and the relationships between different tints of black are kept.
Automation Engine
97
5. If you want to keep certain colors pure after conversion, click Keep Colors Pure... and select
Yes for the colors you want to keep pure (or use a SmartName resolving to YES).
Keeping a color pure means that the conversion will not use other inks to reproduce that color. So for example a 100% yellow object will be converted to the percentage of the output yellow that gives the closest color on print, but will never be made of 97% yellow and
3% magenta.
This helps you avoid unwanted printing effects, like having small dark dots in an otherwise smooth color patch (also called "contamination"). Removing those small dots increases the color difference slightly but avoids graininess on print.
You can choose to keep primary colors ( Cyan, Magenta, Yellow) and/or secondary colors
( Red, Green, Blue) pure. Secondary colors are made of a combination of primary colors (for example green is a combination of cyan and yellow).
You may want to keep certain colors pure and not others depending on the results you get with your particular job or press.
171
97
Automation Engine
• When you keep a primary color pure, all tints of that color are kept pure (so an object that is 50% yellow will stay only yellow). Objects that are already multicolor (for example
50% yellow + 15% magenta) will be converted as normal.
• When you keep a secondary color pure, all tints made of equal amounts of primary colors are kept pure (so for example 50% cyan + 50% yellow is kept pure, but 50% cyan +
60% yellow is not).
By default, the primary colors are kept pure.
Note: When using the Absolute Colorimetric rendering intent, the colors are not kept pure in the very light colors, in order not to interfere with background simulation.
6. Select what objects in your file you want to convert in Apply on. This can be either:
• Images and Linework,
• Linework only,
• Images only.
You can also set this with a SmartName, resolving to images_and_linework, linework_only or images_only (SmartNames are case insensitive).
7. Select Keep registration color if you use marks in your file and if you don't want them to be converted to the new profile (you want them to stay 100% of each CMYK color).
8. Select Flatten document if you are experiencing unexpected results in color conversions (if after conversion the color of some blend modes or other objects on top of each other looks different).
Attention: We recommend you only use this in case of conversion problems, as it will remove any transparencies in your file.
Note: Flattening your file turns vignettes into images. This means that:
• If you selected Flatten document, vignettes will be color converted when you chose to convert Images and Linework or Images only.
• If you didn't, they will be converted when you chose to convert Images and Linework or
Linework only.
97.2 Reseparating your CMYK File
Reseparating a file is replacing some amount of Cyan, Magenta and Yellow in the file (that would give grey) by a certain amount of Black, giving the same grey color.
Objects that are only Cyan, Magenta or Yellow (or only two of these colors) are kept as they are.
This can help you save on CMY inks, have a more stable output (less risks of color casts in neutral areas) or have more detail in the shadow areas.
In Actions, select Reseparate to reseparate a CMYK file so that it contains less CMY and more
K, while keeping the image looking the same.
This displays extra parameters below it.
172
Automation Engine
97
1. Choose the profile to use when reseparating your input file: a) In CMYK Profile, select the profile to use in case you are not using your input file's profile.
This can be an Esko or an ICC profile and you can use a SmartName (resolving to the full profile name) to set it. By default this is ISOcoated_v2_eci.icc.
b) If your input file has a CMYK profile and you want to use it for reseparating, select
Use
document profile if available.
When processing a file without a profile, the task will use the CMYK Profile you selected.
2. Select what type of reseparation you want to do in Purpose:
• Ink Saving replaces as much CMY as possible by Black.
This is a good choice if you want to save on CMY inks.
• GCR (Gray Component Replacement) replaces CMY by Black in the grey and the saturated areas.
This is a good choice if you want to avoid color casts in the grey areas, and to avoid having too much ink in the dark saturated areas, which could cause problems with the substrate.
This is selected by default.
• UCR (Under-Color Removal) only replaces CMY by Black in the dark neutral areas.
This is a good choice if you want to avoid color casts in the grey areas, and to have more detail in the shadow areas.
In the example below, you can see the results of applying ink saving on your file. The first row shows the original file, and the second row shows the file after applying ink saving.
173
97
Automation Engine
174
1. Original file, CMYK separations
2. Original file, CMY separations
3. Original file, K separation
4. File after ink saving, CMYK separations
5. File after ink saving, CMY separations
6. File after ink saving, K separation
You can see that after ink saving, the file contains a lot less CMY and a lot more K.
You can also set type of reseparation to do with a SmartName, resolving to ink_saving,
GCR or UCR (SmartNames are case insensitive).
3. In Range, choose how much of the CMY inks that can be replaced by Black you want to actually replace.
This depends on the Purpose you chose:
Automation Engine
97
• For Ink Saving, this is how much CMY inks in all areas of the file you want to replace.
• For GCR, this is how much CMY inks in the grey and saturated areas of the file you want to replace.
• For UCR, this is how much CMY inks in the grey areas of the file you want to replace.
Note: You can set all percentage values in this task with SmartNames.
4. In Total Ink, select the maximum amount of ink (CMYK) that you want to print.
If you don't limit the amount of ink, you can get a maximum of 400% (100% Cyan + 100%
Magenta + 100% Yellow + 100% Black), which tends to cause problems on most substrates
(slow drying, web growth, or even a risk of tearing).
Additionally, limiting the maximum amount of ink used can make printing jobs less expensive.
The maximum percentage of ink you should use depends on your printing process and substrate. For example for newsprint, you may only want to have a maximum of 240%, while you may be able to use 280 to 320% on a glossy substrate.
The default Total Ink percentage set in the task is 310%.
5. Define the minimum and maximum amount of Black that you want to have in your output file: a) In Start K, define from which (minimum) final Black value you want to start reseparating.
If replacing CMY by Black in a certain color gives a Black percentage lower than this, the
CMY won't be replaced.
This is to avoid having really small Black dots, which can be prone to high dot gain, making them less stable than the equivalent CMY dots.
b) In Max K, define until which (maximum) final Black value you want to start reseparating.
If replacing CMY by Black in a certain color gives a Black percentage higher than this, the
CMY won't be replaced.
This is to avoid having too dark shadows and losing detail.
6. Select what objects in your file you want to reseparate in Apply on. This can be either:
• Images and Linework,
• Linework only,
• Images only.
You can also set this with a SmartName, resolving to images_and_linework, linework_only or images_only (SmartNames are case insensitive).
7. Select Keep registration color if you use marks in your file and if you don't want them to be reseparated (you want them to stay 100% of each CMYK color).
8. Select Flatten document if you are experiencing unexpected results after reseparating a file (if after reseparation the color of some blend modes or other objects on top of each other looks different).
Attention: We recommend you only use this in case of reseparation problems, as it will remove any transparencies in your file.
175
97
Automation Engine
Note: Flattening your file turns vignettes into images. This means that:
• If you selected Flatten document, vignettes will be color converted when you chose to reseparate Images and Linework or Images only.
• If you didn't, they will be converted when you chose to reseparate
Images and Linework
or Linework only.
97.3 Converting and Reseparating your File
When converting and reseparating your file(s) at the same time, you need to:
1. Select the Source profile, Destination profile and Rendering Intent for the
you want to do and set the appropriate options.
3. Select on which objects to perform both the conversion and the reseparation, whether to keep objects in registration color untouched, and whether to Flatten your file.
Attention:
• When using one Manage Color task to both convert and reseparate, the conversion will try to keep the black channel unchanged, so as not to affect the reseparation.
• When using two Manage Color tasks after each other, one for conversion and one for reseparation, this will not be the case, so the output will be different.
If you want to perform both conversion and reseparation on your file(s), we recommend you use one Manage Color task for both instead of a task for each in your workflow.
176
98. Manage Milestone
The Manage Milestone task is documented
here
in the chapter on
Jobs
.
Automation Engine
98
177
99
99. Manage Product Status
This task is documented in the chapter on
Products
. Find a direct link
here
.
Automation Engine
178
Automation Engine
100
100. Map Data
This task is documented in the chapter Integrating with External Systems. Find a direct link
here
.
179
101
Automation Engine
101. Mark as Proof
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
180
Automation Engine
102
102. Mark File (link)
This Workflow Control is documented in the chapter "Workflows". See
Mark File and Select
Marked File
.
181
103
Automation Engine
103. Merge PDF Files
This task combines multiple PDF files into one single PDF.
Multiple native PDF files can be merged into a single native PDF file. Multiple normalized PDF
Files cam be merged into a single normalized PDF File.
Take the following notes into account when using this task:
Note:
• Normalized and native PDF files cannot be mixed together.
• The page sizes of the normalized PDF files must be the same.
• The output PDF will only be normalized if all the input files are normalized files and have the same media and trim boxes. In case there is a mismatch in size, the task will fail.
• For normalized PDF files, the XMP information of the first file will copied into the resulting
PDF file. Then it will be updated with information from the other normalized PDF files.
• All pages of all incoming PDF files are added in the same order as the inputs of the task. To control the order of the files, use the Workflow Control
Sort
.
182
Automation Engine
104
104. Modify Workflow Parameter Values
This Workflow Control is documented in the chapter "Workflows". See
Modify Workflow
Parameter Values
.
183
105
Automation Engine
105. Normalize PDF File
Note: Learn about the concept of 'Normalization' in
Normalized PDF in Automation Engine
.
105.1 Colors
You here define how (non-process) colors will be converted during Normalization.
Note: The conversion uses the technology from Esko's Color Engine.
Objects With Profile Tags: Choose how to convert non process color images that have an embedded ICC profile:
• Ignore Tag: To use the Default RGB Profile or Default Gray Profile (that you define below) to convert the RGB or gray images. This disregards the images' own profiles.
• Convert Using Profile Tag: To use the images' own profiles to convert them to CMYK.
•
Rendering intent
• Relative (no background): Choose this if you do not want any background simulation.
The white point of the source will be mapped on the white point of the destination process. This rendering intent takes into account the ability of the human eye to adapt to the surrounding white.
• Absolute (background): Choose this if you want background simulation and you want an exact color match, including the paper simulation.
• Perceptual: This will result in no background simulation (white of reference color space is mapped on white of destination color space). Choose this when you don't care too much about an exact color match but when want the pictures at least to look nice on your proofer. It will give a visually pleasing result. If the gamut of the source is wider than the proofer, the entire gamut is shrunk so that it fits inside the gamut of the proofer.
• Saturation: Choose this if you care especially about saturated colors. This rendering intent will map saturated colors on saturated colors.
Default CMYK Profile: Select the default profile to use for CMYK objects without an embedded color profile. It will be used as a source profile for color-space conversions.
You can choose any CMYK profile in the Color Engine database.
Default RGB Profile: Select the default profile to use for RGB objects without an embedded color profile. It will be used as a source profile for color-space conversions.
You can choose any RGB profile in the Color Engine database.
Default Gray Profile: Select the default profile to use for gray objects without an embedded color profile. It will be used as a source profile for color-space conversions.
You can choose:
• any gray profile in the Color Engine database
184
Automation Engine
105
• Convert to Black Channel, if you want your grayscale object to only have a value in the
Black separation when outputting it to CMYK.
Output Color Profile: Enter the color-space of the output device (for example proofer or press) .
You can choose any CMYK profile in the Color Engine database.
105.2 Separations
You here define the ink attributes.
Note: The settings in this tab only affect the Normalized PDF output file. They are ignored again if the file is later output as a native PDF.
•
Use ink attributes from file if available: If the input file contains rulings, angles and dot gain compensation, select this option to use these attributes. Other settings in this tab will be overruled. This option is relevant when you normalize PDF files that were exported from earlier normalized files.
• Choose your
Preferred Ink Book. When you type an ink name in the table, the task will first look up its color information (CMYK, RGB, or LAB values) or the ink type (Technical, Varnish,
Opaque...) directly in the PDF. If it cannot find it there, it will look it up the
Preferred Ink
Book that you define here.
For example, if you type 154 as ink name, and your preferred ink book is Pantone Colors
Uncoated, the task will automatically suggest the PANTONE 154 Uncoated ink.
• In the Inks panel, click an (empty) item in any column to change or add or select a new value.
• The
Ink Book column shows the first ink book containing this ink (or your Preferred Ink
Book if it contains the ink). To select another ink book, click the name of the ink book.
• If the
Ruling, Angle and Dot Shape information are defined for this ink, they will be shown automatically. If they aren't, you can enter them manually.
Note: You can also specify Default Values to use when a ruling, angle or dotshape is
not specified (in the file or in the above panel).
• If the Ink Type shown is not correct, click it to change it.
• Do the same for any remaining inks you want to define.
• If you want, you can change the ink order using the Move Up and Move Down buttons.
185
106
106. Normalize PostScript / PDF /
Illustrator 8.0 File
Automation Engine
106.1 Pages
186
Page selection
Define which pages you want to keep in your output PDF file. Select All Pages or specify a
Range.
Split Up a Multi-Page File
Select this to split the multi-page input file into multiple output files.
• Maximum Pages per File: Define the amount of pages you want in each output PDF file.
The last output file can have less pages than this value. Each output file is saved with a numbered suffix (*_001, *_002, *_0001_001…) or it gets the Output Name.
•
First Page number in Output
You can here define the "label" of the first page in the output. For example: when you normalize a 4 page document, and set '3' in this field, the pages will be labeled 3-4-5-6.
Merged Tiled CT Files to one CT
Some ArtPro files include tiled CT images. Large size graphics can so contain thousands of these small CTs.
Select this toggle to merge these tiles back into one CT. This so improves the editability and processing of the output file.
This option has no effect when you import a file that has no tiled CTs.
Merge Separated File to Composite Page
Automation Engine
106
This option merges separated PostScript or PDF files (single- or multi-page) to a composite PDF file.
• Optimize Merged File. Use this option when you need to edit the resulting file.
• Password: When normalizing password protected PDF files, enter its password here.
106.2 Color Management
106.2.1 Destination Color Space
You here define the color space of the output file.
• Color Space: Choose CMYK or Grayscale.
• Destination Profile: Choose a color profile. Only CMYK and Grayscale profiles are supported. Choose between standard ICC profiles and Esko profiles made in Color Engine
Pilot.
• Use PDF Output Intent if available: In some PDF files, the 'PDF Output Intent' is defined, this is the intended output color space. For example PDF/X-3.
If you want to use the color space as defined in this 'Output Intent', select this option. If you selected it for a file without PDF 'Output Intent', the chosen Destination Profile will be used.
• Set Document Profile: A Document Profile is the color space of the process inks used in the document.
• Always: You can 'tag' a Normalized PDF file with its Document Profile. This means that the file knows what its Document Profile is, which can make color conversion further in the workflow more correct.
If you selected ' Use PDF Output Intent if available', the Document Profile will be the same as the PDF Output intent (if the imported file had one).
• From PDF File: (available when 'Use PDF Output Intent' is selected). The Document
Profile is taken from the PDF file, if there is an output intent defined in the PDF file. If
187
106
Automation Engine
there is no Output Intent defined in the PDF file, then the Document Profile is not set
(untagged).
• Never: The Document Profile is not set.
106.2.2 Spot Colors
•
PANTONE Inks
• Keep all: No PANTONE inks will be converted to process inks.
• Convert all: All PANTONE inks will be converted to process inks.
• Keep list: All PANTONE inks will be converted except for those listed in the tab
.
Method
• Use destination profile: PANTONE and Designer inks will be converted using the selected Destination Profile. This gives the most accurate color reproduction.
• Pantone+ Color Bridge Coated: Pantone inks will be converted to process inks according to a fixed conversion table provided by PANTONE. The result is independent of the selected Destination Profile.
•
Other Inks
• Keep all: No other spot color inks will be converted to process inks.
• Convert all: All other spot color inks will be converted to process inks.
• Keep list: All other spot color inks will be converted except those listed in the Inks tab.
106.2.3 RGB
RGB will always be converted to process inks.
• Convert: Select a conversion method:
• Source to destination profile: You here need to specify both the Source Profile (RGB) and the Destination Profile (CMYK or Grayscale).
• With link profile: You here need to specify a 'Device Link Profile' created in Color Engine
Pilot. This link profile determines both the Source and Destination profiles.
• Source Profile / Link Profile: Select one from the list.
• Objects with RGB Profile Tags: RGB objects in a PostScript or PDF file may be tagged with a
Color Profile.
• Ignore tag: The embedded Color Profile will be ignored. The Source / Link Profile defined above will be used for the conversion of RGB objects.
• Convert using profile tag: The Color Profile is used as a Source Profile (overruling the
Source / Link Profile selected above).
188
Automation Engine
106
106.2.4 CMYK and Gray
Objects in a PostScript or PDF file may be tagged with a Color Profile. The color percentages of untagged objects will always be preserved.
Both for CMYK and Gray tagged objects, you have a choice:
• Ignore tags, preserve percentages: The Color Profile tag will be ignored, the percentages will be those of the object's color.
• Convert, preserve appearance: The objects' color profile will be taken into account. This means that their color values will change.
106.3 Inks
• Use rulings, angles and dot gain compensation from file if available: If the input file contains rulings, angles or a dot gain compensation description, select this option to use these attributes. Other settings in this tab will be overruled.
This option is relevant when you import DeskPack (EPF) files or when you normalize PDF files that were exported from earlier normalized files.
• Force ink settings from Job setup : If inks were defined in your
Job setup
, you can use this toggle to make sure that this task uses those ink parameters.
• Apply Screen Swap Table: You can create 'screen swap' tables in the application
'ScreenFilter'. Select one to map PostScript screening to Esko screening.
189
106
Automation Engine
• Map PANTONE Inks to: Select this to map all Pantone inks from the input file to a Pantone ink book of your choice. For example: to map Pantone 123 U to Pantone 123 C .
• Use ClassicColors ink book: When the input file has inks with names that also occur in the book 'ClassicColors' (for example "green"), select this option to map them to those in that
ClassicColors book (in stead of becoming a 'designer' ink).
• Search Custom Ink Names: Define here the task should search for inks in its ink books when you type in an ink name in the Inks table.
• Choose
Only in the ink book 'designer' to search for ink names from the 'designer' ink book only.
• Choose First in <selected ink book> and then in 'designer' to search in another ink book of your choice first, and only use the designer ink book if no match is found there.
•
Inks table
Double-click the fields in this table to edit them. The task will not change the inks that you here deselect.
Default values, used when a ruling, angle or dotshape is not specified: The task uses these default values when they are not specified elsewhere (for example in the PostScript file, in the Job setup, etc.).
106.4 Overprint
Note: This tab is only relevant when importing PostScript files.
190
•
Strict overprint behavior
When normalizing composite files, this option controls how zero percentage inks are handled.
Attention: This option must be used when you want to process test files like the
Altona test suite or other test suites which verify correctness of overprint behavior.
When 'Strict Overprint' is used, all zero percentage inks of a color are kept and correspondingly affect the overprint behavior. Choose from:
• Never strict overprint behavior: All zero percentage inks are removed.
• Always strict overprint behavior: The task honors the overprint parameter 100% according to the rules mentioned in the "PostScript Language Reference" (in case of
PostScript / EPS /AI import) and "PDF Reference Manual" (in case of PDF import).
Automation Engine
106
• Only strict overprint behavior for PDF: The task honors the overprint parameter 100% according to the rules mentioned in the "PDF Reference Manual" (in case of PDF).
•
Overprinting default is non-zero overprinting
Select this option to prevent overprinted objects with zero CMYK values from knocking out
CMYK objects beneath them.
• Default: Choose the overprint mode that the conversion needs to apply.
• Opaque: Ignores any overprint in your file.
• Darken (Esko): Converts all overprint to Esko Overprint.
• PS Overprint: All overprint in the file is imported as PS overprint. This is the default setting.
•
Pure Black
Define the overprint mode for objects containing 100% black only. Possible Pure Black overprint modes in the list:
• Default: As it is defined in the file.
• Force opaque: Forces Opaque for objects in 100% black and knocking out all underlying inks.
• Force PS overprint: Forces PS overprint for objects in 100% black.
• Force darken (Esko): Forces the Esko darkening mode for all objects in 100% black.
The black color is so printed on top of other colors, instead of erasing the color underneath.
•
Rich Black
Define the paint mode for objects containing 100% black and at least one other ink.
• Default: As it is defined in the file.
• Force opaque: Sets the overprint mode to opaque for all objects containing 100% black and at least one other ink.
• Force PS overprint: Keeps the PS overprint for objects in 100% black and at least one other ink (overprint objects stay in overprint and opaque objects stay opaque).
• Force darken (Esko): Sets the Esko 'darken' overprint for all objects in 100% black and at least one other ink.
•
White
Define how you want whites to be handled:
• Keep PS overprint: Keeps the PS overprint for objects in white (overprint objects stay in overprint, opaque objects stay opaque).
• Opaque: Forces all objects in white to opaque.
191
106
106.5 Images
Automation Engine
192
• Embed all images: Select this if you want to embed all 1–bit, 8–bit and native images into the output file. When not selected, only images with uncompressed image data smaller than 640 kB will be embedded.
Note: This is the only option in this tab that is relevant when normalizing PDF files.
• Optimize DCS LineWork: When DCS linework is not optimized, the result can be difficult to edit afterwards. However it will be correct when viewed in extended preview or RIP'ed.
Select this option to trigger an additional operation that combines the elements on each
DCS plate to a composite and a more editable result.
• Search for preconverted Files: This option forces the task to look for the CT, LP or GR* equivalent for the original EPS file. If this equivalent is not found, it will use the EPS instead.
• Link external images (OPI, DCS, Helios, ...): This option forces the task to look for referenced images.
• Fail if not Found: Select this option if you do not want the task to continue when it cannot find an image. When not selected, the task will create an output file but one with missing images.
• Images: This option determines how images are treated when the task is run:
• Reconvert: This forces the system to regenerate the images on-the-fly.
• Use most Recent: This forces the system to use the existing images of a previous conversion of the same file.
•
Use masks
• PS mask: This forces the system to take the PostScript (PS) mask present in the EPF file.
The mask available in the external image is discarded. If no PS mask is present in the file, no mask will be taken.
Automation Engine
106
• External mask if any, PS mask otherwise: This forces the system to take the mask present in the external image. The PS mask is discarded. When the external image has no mask, but there is a PS mask available in the EPF file, this PS mask will be taken.
• External mask if any, no mask otherwise: This forces the system to take the mask present in the external image. The PS mask is discarded. When the external image has no mask, no mask will be taken.
• No masks: The PS mask and the mask of the external image are discarded.
• Joined external and PS mask: This forces the system to join the available PS mask in the EPF file and the available mask in the external image.
• Search directories: You can here specify a list of directories where the system should look for referenced images.
Use the ' Add' and ' Remove' buttons to create this list.
• Path Translation...: This option serves to create a list that helps translating network paths from one platform to another. Click the button to open a dialog and define three columns:
• From platform: Click on the field to select a platform from which the files are to be retrieved: (Windows) NT, Mac, Unix or VMS.
• From path: Define the syntax of the path(s) of the platform you want to retrieve files from. For example Mywork:BigCustomer:job1 .
• To path: Define the syntax of the paths so that the destination platform understands.
For example Mywork/BigCustomer/job1 .
An example: when going from Mac to Windows NT, the path translation can look like this:
• File Translation...: The same kind of translation can be done for file names.
106.6 Page Size
193
106
Automation Engine
Note: The units are those defined in Edit > Preferences > Units .
• Page Size: Select the page size (Media Box) that you want for the output PDF file. Choose
' PS page size' to keep the size of the input PostScript or PDF file.
•
Reader's Spread: When the input file has a reader's spread format, choose from:
• No: To force the reader's spread in the file into single page output.
• Yes: To force the file into reader's spread format. When the file contains no reader's spread info, the single pages will be set as double pages.
• Scale: If you want, enter a vertical and/or horizontal scale.
• Rotate: If you want, choose a rotation. The origin for rotation is bottom left and the available rotations are counterclockwise.
• Offset: These fields allow to move the content of the file in regards to the page size. The anchor point for the offsets is bottom left. A positive offset moves the content of the file up and/or to the right. A negative one moves the content of the file down and/or to the left.
106.7 Other
194
•
Substitute Missing Fonts
• Roman Fonts by: Choose a default replacement font for any missing Roman fonts.
• Japanese Fonts by: Choose a default replacement font for any missing Japanese fonts.
• Fail if Font Not Found: Select this to make the task fail when a font is not found.
•
Images
• Import 1-bit images as:
• Embed: Images become internal black and white bitmaps.
Automation Engine
106
• Linked file: Images are imported as external referenced LP files (Esko native bitmap files).
• Contours: Images are contourized during import.
• CT display images: Choose Yes to have the task also create a display image for the generated CT files.
• Output file display images: Select the type of display from the list: None, Thumbnail or Image and Thumbnail.
•
Miscellaneous
• Device resolution: The resolution that the task uses internally during normalization.
Normally the produced output is not dependent of this internal resolution. However, in some rare cases, for example when converting RIP'ed test strips or device specific tests, it is important that this value is the same resolution as used on the RIP device that will be used to output.
•
Virtual Memory limit: The default value is 50 Mb. The maximum you can set is 1 gigabyte (1024 Mb).
• Convert text to contours. Select this to convert all text to line work.
•
Workaround Options
• Skip images: Select this to import the (E)PS file without linking to external images or converting embedded images.
• Preserve Quark trapping: Select this to force the task to keep the trapping strokes made by QuarkXpress.
• Disable optimizations: When not selected, the task performs a recognition of vignettes and an optimization for Photoshop multitone images (whenever possible). Disabling such optimizations was useful when an older version of the task could not yet perform the optimization of the (E)PS file that a new DTP application had exported.
• Show PS comments: When selected, all 'PS comments' present in the (E)PS file are mentioned in the task Details and in its Log file.
• Disable OPI: This option is useful when importing QuarkXpress (E)PS files that contain high resolution Tiff files for which the option 'Include tiff, omit ...' or 'Include all' was activated.
When importing such a file, and if Link External Images is selected, the matching of the TIFF files will surely fail. It fails because at the time the (E)PS file was generated, OPI commands were also inserted for the TIFF files. Therefore the system will try to link to images for the Tiff files. To overcome this, select this option.
• Show external images searches: Select this to see, in the task's log file, the path(s) where the task finds and links to external images.
• Optimize Illustrator Patterns: Adobe Illustrator writes patterns in a different way than
PostScript does. This option normally results in less linework in the output file, which
195
106
Automation Engine
then speeds up the further processing. However, sometimes the optimization itself may take some time.
• Use PostScript rules for color conversion: Select this to make sure that all color management will happen using PostScript rules, instead of Esko's BGCMS. Selecting this
option grays out most options in the
.
• Object Based Color Conversion: 'Object by object' color conversion does not take overprint and transparency interaction between objects into account, and may therefore produce undesirable results. However, it may greatly improve editability.
106.8 Output
• Keep Layers. Select this to keep the input file's layer information. This works for Illustrator
8 files (not v9 nor higher) and for PDF 1.5 or higher.
• Fit Media Box (margins). Select this to automatically fit the margins.
• Image Directory. When the task creates new image data, you can here indicate where these images should be written.
The default offered SmartName [Job CT URL] will create them in a 'CT' folder that is created in the root of the input file's Job Folder. Leave the field empty to have the image files written next to your output file. Or select your own (central) folder and possibly add
SmartNames to that path.
196
Automation Engine
107
107. Normalize TIFF/IT File
This old technology is still supported but no longer commercially available.
Please find its documentation in the
manual of Automation Engine 14.1 or older
(as part of the
Reference Guide).
197
108
Automation Engine
108. Optimize and Clean (PSFix)
PSFix is an Esko technology that optimizes and cleans files that were imported from PS or PDF files. A typical feature is the removing of redundant objects. The resulting file is easier to edit and process.
This task is typically executed right after a conversion to Normalized PDF.
108.1 General
198
•
Delete
• Spurious Contours: These are
• Single points that only have a fill attribute.
• Single points that have a stroke attribute with butt or square caps.
• Contours that contain two points and that have a mask attribute, but do not mask out any object. These contours can be created by accident or generated by PostScript printer drivers.
• Double Contours: This removes double contours by recombining the fill and stroke attribute of two identical objects into one object again. Double contours are created when importing PostScript files, in which case an object with a fill and a stroke attribute is split into two objects with each one attribute.
• Gross Clipping: This deletes the objects whose bounding boxes fall completely outside the bounding box of the clipping path. This also works on composed text and externally referenced objects.
Automation Engine
108
• Useless Clips: This deletes useless clipping paths, objects that are totally clipped away or objects that are totally covered by other objects.
• Hidden Objects: This deletes objects that are completely covered with another object.
The designer did not want to delete them or could not delete them on a certain page, as they may have been components of a master page.
• Contours outside margins: This deletes contours outside the margins.
• Clean up unused inks: This removes all unused inks from the list of inks (separations).
• Clean up unused inks and colors: This removes all unused inks and also unused colors
(items in the color palette of the editing application).
•
Strokes
• Regenerate Strokes: This searches objects that contain 20 points or less and converts them to the equivalent strokes.
Select ' Complex Objects too' if you want the task to search all objects that might be degenerated strokes, so also those with more than 20 points.
• Minimal Linewidth: This defines the minimal width of strokes.
•
Correct
• Blend to CT: This converts all blends to externally referenced CT images at a defined
Resolution (1 image per blend).
In PostScript files, blends are constructed by a large amount of contours that lie close to each other and that have slightly different colors. The more accurate the blend, the more contours and colors it is made of. This leads to large file sizes and decreases the processing speed.
Note: After this conversion, the display of the blend can be different. However, the conversion does not affect the printed result.
• Simplify Linked Mask Objects: This tries to reduce the number of linked contours for complex mask objects. This option is only useful for linked mask objects with a large
number of contours (>50).
199
108
Automation Engine
• Fix bleed: This task can automatically create bleed. Bleeds for linework objects are created in a new layer called " Bleedlayer". This layer can always be removed to return to the original file. This is not possible with images. Images are modified in their original location.
• Bleed Distance: This is the minimal amount of bleed that is required. For any object that does not have this amount of bleed the correct bleed will be created.
• Gap: Any object inside the 'borders' (Trim Box), and that is closer than this distance to the borders will be considered to require bleed. Typically, this value will be small. It makes sure that objects which do not really touch the borders because of inaccuracies in the design, are taken into account for bleed creation anyhow.
• Maximum Image Scale: There are two possible to fix bleed for images:
• When an image is larger than its clip mask, the task creates bleed by extending the clip mask of the image. Hidden pixels so become visible and the missing bleed problem is fixed.
• When the image is not larger than its clip mask, the only way in which bleed can be created is by scaling the image. The position of the image inside the page does not change, but it is disproportionately scaled to create the correct bleed. To avoid an unacceptable distortion of the image this parameter determines how much scaling of an image is allowed. Set the value to 0 to prevent any scaling.
In order for the bleed-fixing to work properly it is imperative that the borders of the file are set correctly (see the tab
on page 200).
Note: When bleeds have been corrected, the task will end with a warning. When the maximum scale factor was not enough to create bleed for an image, the task will end in error.
• Put knocked-out technical inks object in overprint: This forces objects in technical inks in overprint mode.
108.2 Borders
200
Automation Engine
108
• Adjust Borders: Select this to enable these options:
• Fit borders to: Choose All inks or one from your input file (for example its ink 'CAD').
• Auto Fit Borders on Trim Marks: When the task can detect trim marks, the borders will be set accordingly.
This option is useful when the trim size of the input file is unknown or unreliable (for example a missing or wrongly defined trim box in a PDF file). Even when the desired trim size is known to the user, it can still be interesting to see if the automatically determined border size corresponds to the desired one: a difference between the two is likely to point to an error.
Note that the intelligent placement of files in FastImpose and Plato allows users to
neglect to work with accurately set borders. However, if you want to
a requirement to have the borders defined correctly.
• Move Borders: You can manually move any of the borders for Even and/or Odd pages.
• Auto Fit Margins on Trim Marks: To fit the Media Box to any trim marks.
• Fit Margins: To fit the Media Box to any objects in the file.
• Set Margins: To define a specific value for the Media Box.
201
109
Automation Engine
109. Optimize PDF Document
This task enables you to make some prepress-specific changes to a PDF document. It so avoids having to stop a workflow task to do such edits in an interactive application.
The output will be PDF when the input file is a native PDF. The output will be Normalized PDF when the input is a Normalized PDF or a PDFPLA file.
109.1 Document
•
Optimize Document
• Preserve fonts: Select this make sure your fonts will print or display correctly. Choose a method:
• Embed Fonts: This embeds all used fonts.
•
Embed & Rename: This embeds 'Base 14 Fonts' under a different name (their name in the Esko PDF Library), and all other fonts under their existing name. This prevents
Acrobat from replacing the document font with a local font of the same name when using live text.
Note: 'Base 14 Fonts' are: Courier, Courier Bold, Courier Oblique, Courier Bold-
Oblique, Helvetica, Helvetica Bold, Helvetica Oblique, Helvetica Bold-Oblique, Times
Roman, Times Bold, Times Italic, Times Bold-Italic, Symbol and Zapf Dingbats.
• Vectorize: This converts all text to outlines.
• Apply document's rotation flags: In a PDF file, a 'rotation flag' specifies by what angle the contents should be rotated when previewing or printing the file.
Some older applications and devices ignore or mishandle this rotation flag. If you are sending your file to such an application or device, select this option to execute the rotation specified in the rotation flag.
• Outline strokes: Select this to convert the strokes to outlines. Choose Dash Only to only converts dashed strokes into individual outline objects. This can significantly improve trapping.
• If you want to change the strokes' width in your document, select
Increase line width
and enter a Minimum Line Width. All strokes with widths below this value will be enlarged to that width.
• Rotate File: Select this to rotate the contents of your file (clockwise). This may be needed to make the contents fit on a certain device.
• If Apply document's rotation flags is not selected, this changes the rotation flag's value but does not rotate the file's contents.
• If Apply document's rotation flags is selected, this rotates the file's contents.
• Adjust Page Box: Use this to change some or all of the document's page boxes, or add page boxes in your document. Learn more in
202
Automation Engine
109
• Outline Page Box: Use this to outline some or all of the document's page boxes. They then
become visible on proof for example. Learn more in
on page 204.
109.1.1 Adjust Page Box
To add or change a page box:
1. Click Add to open the Adjust Page Box dialog.
2. Select the Page Box to add or change.
3. Choose what you want the new size to be Based on:
• Choose Absolute (Background) if you want to define the page box size independently of the file's contents or existing page boxes.
• Choose Content if you want to base the page box size on the file's contents. This takes clipping paths and masks into account.
• Choose Media Box, Crop Box, Trim Box, Bleed Box or Art Box if you want to base the size of the selected page box on that of another one.
4. Define the new Width and Height.
• If you have chosen to use an Absolute size, enter the page box's Width and Height.
• If you have chosen to base the page box size on the file's Content or on another page box, you can adjust the width and height in Increase Width and Increase Height.
Note: Use a negative value to reduce the page box size instead of extending it.
5. If you want, enter an Horizontal Offset and / or a Vertical Offset.
• A positive horizontal offset will move the page box to the right, a negative one to the left.
• A positive vertical offset will move the page box to the top, a negative one to the bottom.
Note: This is applied after the Alignment was done!
6. Choose the page box's Alignment (relatively to the old page box):
203
109
Automation Engine
7. Apply your changes to either All Pages or only to the Odd or Even Pages.
8. Click the Add button to confirm.
Note: You can adjust multiple Page Boxes.
109.1.2 Outline Page Box
To outline a page box:
1. Click Add to open the Outline Page Box dialog.
2. Select the Page Box to outline.
3. Define the Ink for the stroke to use.
Type an Ink Name, use a SmartName or click the color patch to open a color picker.
4. Enter the ink Density to use.
5. Specify the Stroke Width to use.
6. Click the Add button.
204
Automation Engine
109
109.2 Layers
•
Action 1: Rename Layers
Click
Add and enter the Old and the New Layer Name. You can use SmartNames and / or wild cards (to replace part of the layer name).
Tip: You can also merge layers by renaming a layer to an existing layer's name, or by renaming several layers to the same name. This works for layers that are directly on top of each other in the file.
•
Action 2: Remove Layers
Click Add and enter the names of the layers you want to remove. You can use SmartNames and / or wild cards.
Except for: When using a wild card to remove layers, use this parameter to keep certain layers, even if they match the name entered in Remove Layers.
•
Action 3: Add Layers
Use this to add empty layers to all pages of your PDF.
Click Add and enter the name of the layer to add. Repeat as necessary.
• Update Layer Print-ability: Select how to handle the print-ability of layers in your output file:
•
Don't Change Layer Print-ability
•
Make All Layers Printable
• Remove Non Printable Layers.
109.3 Images
•
Downsample Images
205
109
Automation Engine
Select this to lower the resolution of the file's images.
• Choose what resolution you want to Downsample bitmap (black & white or one-bit)
images to, if their resolution is above a certain resolution.
• Choose what resolution you want to Downsample contone (grayscale or color) images
to, if their resolution is above a certain resolution.
•
Crop Images
The tasks can remove unused image data from the PDF by cropping images on the bounding box of their clip path. Cropping images is done to make PDFs smaller.
Split images area when at least ... % of the images is clipped away: This parameter defines how the task will crop the image, depending on how much of it is clipped away (for example for images that have multiple clipping paths on them).
• If the part of the images that is clipped away is less than the value you enter here, the images will stay together and be cropped to the bounding box of the combined clipping paths.
• If the part of the images that is clipped away is greater than the value you enter here, the images will be split into multiple clipped images, each cropped to the rectangular bounding box of its clipping path.
•
Recompress Image Data
• For Color, Gray Scale and Soft Mask Images, you can choose between the JPEG and ZIP compressions.
• For Bitmap Images, you can choose between the CCITT Group 3, CCITT Group 4, ZIP, and Run Length compressions.
206
Automation Engine
110
110. Optimize PDF Separations
This task enables you to make changes to the separations of a PDF file.
The output file will be PDF when the input file is a native PDF. The output file will be
Normalized PDF when the input file is a Normalized PDF or a PDFPLA.
When the input is a multi-page file, all requested functionality is executed on all pages.
110.1 Colors
You here define how to convert the file's (non-process) colors.
Note: The conversion is done by Esko Color Engine.
• Embed Profiles Mode: The task uses embedded profile(s) as source profiles for conversions. Choose from:
• Do not change: This doesn't make any changes to embedding of color profiles.
• Embed: This embeds all color profiles.
• Embed & Overwrite: This re-embeds all color profiles, overwriting profiles that were already embedded.
• Remove All Embedded: This removes all embedded profiles.
• Convert RGB, LAB, Gray to CMYK: Select this to convert all non-process color spaces
(except spot colors) to CMYK.
Note: This will generate errors and/or warnings when trying to convert non-separable blend modes.
• Fail When Converting Color Spaces: Color converting objects that have transparency effects (like blend modes) can generate visually unexpected results. When this problem occurs, you can:
• Select this option if you want the task to stop with an error.
• Deselect this option if you want the task to only generate a warning.
• Default CMYK Profile: Select the default profile to use for CMYK objects without an embedded color profile. It will be used as a source profile for Color Space conversions.
Note: You can choose any CMYK profile in the Color Engine database.
• Default RGB Profile: Select the default profile to use for RGB objects without an embedded color profile. It will be used as a source profile for Color Space conversions.
Note: You can choose any RGB profile in the Color Engine database.
• Default Gray Profile: Select the default profile to use for gray-scale objects without an embedded color profile. It will be used as a source profile for Color Space conversions.
Choose from:
• Any gray profile in the Color Engine database.
207
110
Automation Engine
• Convert to Black Channel, if you want your gray-scale object to only have a value in the
Black separation when outputting it to CMYK.
• Output Color Profile: Enter the Color Space of the output device (proofer or press) in this parameter.
Note: You can choose any CMYK profile in the Color Engine database.
• Update spot color equivalents: This option handles CMYK values for spot color inks. You can:
• Select this option to overwrite the CMYK values found in the file with the CMYK values stored in the ink book.
• Deselect this option to use the CMYK values found in the file for spot color inks.
• Spot Color Lookup: Indicate where the task should look for the spot colors' information.
Choose from:
•
Look in Ink Books First: The task first looks in the ink book you defined in
If it doesn't find the spot colors' information in that ink book, it then looks for it in the file.
•
Look in Ink Books Only: The task only looks in the ink book defined in
If the task does not find the spot colors’ information in that ink book, it ends in error.
• Use Colors in File: The task looks for the spot colors’ alternate color values (generally in the CMYK color space) in the file, and uses those values.
• Preferred Ink Book: Choose the preferred ink book that will be used in this task.
• PANTONE Color Lookup: Choose the settings for the PANTONE colors conversion. Choose from:
• Use destination profile: Use the color profile defined in the Output Color Profile to determine CMYK equivalents of the PANTONE Color.
• HP Indigo CMYK x.x: Use CMYK equivalents for the HP Indigo Press.
• Pantone+ Color Bridge Coated: Use the CMYK equivalents defined in the Pantone Color
Bridge Coated guide.
110.2 Inks
Note: This functionality is executed in the order as numbered: First Action 1, then Action 2, etc.
Caution: All ink-related parameters are case sensitive.
•
Action 1: Remap Inks
Click Add to open the Remap Ink dialog, then enter the Old and the New Ink Name.
Tip: You can also merge inks by remapping an ink to an existing ink's name, or by remapping several inks to the same name.
208
Automation Engine
110
Note: If your original ink has a PANTONE Suffix, add it to the Old Ink Name, even if you are changing this suffix. The reason for this is that when you use both the Remap Inks and
Pantone Suffix parameters, the task renames the inks first.
Pantone Suffix: Use this to change the suffix (for example CV, CVC, CU...) of PANTONE colors. Choose from:
• Do not change.
• Convert: This changes the suffix to the one you select in the To list, for all PANTONE colors.
• Convert If Found In Ink Books: This changes the suffix to the one you select in the To list, for PANTONE colors found in the ink books you defined (in the
Note: This option can also merge inks. For example if you have PANTONE 484 U and
PANTONE 484 C, and you change all the suffixes to C.
•
Action 2: Convert Inks
Use this table to convert spot colors to CMYK. You can use wild cards (*) in the ink's name.
•
Action 3: Remove Inks
Click Add and enter the names of the ink you want to remove. You can use SmartNames and/or wild cards.
Except for: When using a wild card to remove inks, use this parameter to keep certain inks, even if they match the name entered in Remove Inks.
For example, to create a PDF file for the die-cutter, you can remove all the inks except the ink Die cut :
Preserve Separation Interaction: Use this parameter to define what to do when the separations you remove contain objects that knock out other separations.
• None: This only deletes knock-out objects that are only defined in the removed separation(s).
Use this when removing separations that don't influence the final result (for example die cut separations).
• Standalone: This converts knock-out objects that are only defined in the removed separation(s) to white knock-out objects defined in one of the remaining separations.
The remaining separations keep looking the same.
This method is recommended for most use cases.
• For Versioning: This converts knock-out objects that are only defined in the removed separations to white overprinting objects. Those are defined in a color space made from the remaining separations of the file, and overprinting on all other separations.
209
110
Automation Engine
This ensures that when re-adding separation layers for versioning, the final result looks the same as the original file.
Note: This may create objects in 'DeviceN' color spaces, which is something that some applications cannot handle. Only use this method if you want to do versioning on your file.
• Remove unused separations: Select this to remove unused separations (separations containing no objects) from the file.
110.3 Ink Properties
This tab allows to apply extra properties of
Ink Type and Printing Method to the existing inks.
These properties can be used to steer behavior of tasks later on in the workflow, for example
when using the
based on printing methods.
210
•
Apply Ink Type
You can define the Ink Type for each Ink Name. You can use SmartNames and wild cards.
An Ink Type can be Normal, Opaque, Varnish or Technical. Limitations for Opaque can be imposed by the CMS. Process colors (CMYK) can only be Normal.
Note:
• When using wild cards in the ink name, the inks matching that pattern will get the specified properties. If an ink matches more than one pattern, the first one is taken.
• When matching, the letter case is ignored.
•
Apply Printing Method
Automation Engine
110
Set the Printing Method for a specified Ink Name. Choose from the list of printing methods as defined
in the Configure panel
.
110.4 Overprints
Use this these options to change the Overprint versus Knockout behavior of the inks.
•
To Knockout
• All overprint objects: Select this to disable all overprints in your file.
Attention: This can change the file's appearance.
• White text: Use this to set white text to knockout.
• White vector: Use this to set white line art to knockout.
• Technical objects: Use this to set technical objects to knockout.
• Varnish objects: Use this to set varnish objects to knockout.
• Opaque ink vector: Use this to set line art in opaque ink to knockout. Opaque inks are defined in the ink book, using the Color Engine Pilot.
• Opaque ink text: Use this to set text in opaque ink to knockout. Opaque inks are defined in the ink book.
Caution: When an ink is explicitly defined as "opaque" in the ink book, you cannot make it "normal" with this task. You will get a warning if you try.
•
To Overprint
• All knockout objects: This parameter changes all knockout objects to overprinting objects, and modifies their color space(s), so that the file keeps the same appearance.
Attention:
• Only use this parameter in creating PDF versions.
• This parameter affects how you can place the file afterwards. If you place this overprinting file on top of another file, all the channels of the bottom file that are not present in the top file will be visible.
• Black text: Use this to set black text to overprint. You can choose to make:
•
All black text overprint, or
• black text
Smaller Than a defined value overprint.
•
Black vector: Use this to set black line art to overprint.
•
Technical objects: Use this to set technical objects to overprint.
211
110
Automation Engine
• Varnish objects: Use this to set varnish objects to overprint.
• Opaque ink vector: Use this to set line art in opaque ink to overprint. Opaque inks are defined in the ink book.
• Opaque ink text: Use this to set text in opaque ink to overprint. Opaque inks are defined in the ink book.
212
Automation Engine
111
111. Outline Fonts
This task will contourize all fonts in the file and in all the files it refers to. Both live and composed text will be contourized. ‘Internal’ text (executed SmartMarks for example) is already contourized.
The task outputs a different PDF and by default adds the suffix _c to its name (use
SmartNames to overruled this behavior).
Tip: When the input file did not contain any fonts, the
Details pane of the Task
and its log file mention this.
213
112
Automation Engine
112. Preflight with PitStop
This task is documented in the chapter
Quality Control tools
. See
Preflight with PitStop Task
.
214
Automation Engine
113
113. Prepare for Inspection
This task takes a JDF Layout file and creates a JDF Inspection file that will be read by a (press) inspection system. You can set specific measurement points in the design that the inspection system will then monitor.
The task generates
• a JDF Layout file, now with extra information for the inspection system
• a TIFF preview of the to-be-printed material
• a TIFF preview of the shape of the resulting label after die cutting (the 'Cut Mask')
• a MIME file containing all output files.
Note: The JDF Inspection file contains the layout of the sheet(s) and for each one-up PDF the information about:
• the contour of the retained area ( ClipPath)
• the location of the barcodes ( IdentificationField)
• the location of the text areas ( IdentificationField)
• the location and values of Spectrometer measurements (
CIELabMeasurement)
Learn more in
Example Workflow
• This example workflow starts by creating a PDFPLA step and repeat file.
• It then exports this file as a JDF Layout file. This creates a JDF file and a self-contained PDF file for each one-up.
• The
Prepare for Inspection task then uses this JDF layout to create the MIME file containing the JDF file and the TIFF previews.
• The next task publishes this MIME file to a hotfolder to be picked up by the inspection system.
Note: Use the workflow control 'Router' to make sure that the correct files are used as input file for the next step.
215
113
Example of Preview and Cut Mask
Example label (one-up):
Example preview: Note that the cut path is not visible in this preview:.
Automation Engine
Example Cut Mask:
113.1 Settings
Document Tab
216
Automation Engine
113
• Select what the task needs to create:
• Create MIME pack: A self-contained set with all output files. When not selected, the requested output files are created separately.
• Render Preview (TIFF): When not selected, a PDF preview is created.
• Render cut mask (TIFF): When not selected, a PDF preview of the cut mask is created.
• Preview Resolution: Define the resolution of the TIFF files.
• JDF Job ID: Use SmartNames to make this result in the job identification that the inspection system should use to link the printed matter to this file.
• Inspection Parameters: Add extra parameters at will. For example the name of a profile that will define the settings for the inspection system (for example "adhesive label").
Separations Tab
You can here define separations to be excluded, typically all the non-printable, technical inks like “Die Cut”.
217
113
Automation Engine
Note: Using the Adobe Illustrator Plugin "Esko Data Exchange" " or the application Esko
PackEdge, you can include extra annotations inside the PDF file. These can serve to identify areas with different inspection requirements, or could be locations for colour measurements, including their expected LAB values and accepted tolerance. If such information is found inside the PDF file, it is added to the output JDF file.
218
Automation Engine
114
114. Prepare for Viewer
This task is documented in the chapter
Quality Control tools
. See
Prepare for Viewer Task
.
219
115
Automation Engine
115. Prepare Graphics for Nesting
The Prepare Graphics for Nesting task is documented in the chapter
Gang Run Printing for
Sign & Display
. Find a direct link
here
.
220
Automation Engine
116
116. Prepare Station
This task prepares one ups for use in Step and Repeat editor or task.
Note: Some of its features are also available in the more recent task
Prepare Graphics for
Nesting
.
• Create Station File:
Select this if you want the task to create a PDFSTA file instead of a Normalized PDF. See
how the sub-options are different when this is not selected.
Attention: PDFSTA files can only contain external references to Normalized PDF files. So only select this option when the input file is also a Normalized PDF (or the task will fail).
• Extract Die using Ink: When selected, the task creates a die line in the output file by extracting all contours of the specified Ink. This die line will automatically be used in Esko
Plato or in tasks using Plato technology. When not selected, the trim box of the station file will be used as die shape.
• Load CAD: Select this to place a CAD file into the station file (an ARD or a 1-up CFF2 file).
Note: In case a layout CFF2 file is selected, the task will generate an error.
Note: When you only need to load a CAD file into the PDF, consider using the
Mapping: When loading a CFF2 CAD file, choose how the CFF2 line attributes should be mapped to the ArtiosCAD line types. Select the appropriate CAD Style file to determine in which separations the different CAD lines will appear.
Overview:
When loading a CAD file, the following sequence of operations takes place:
221
116
Automation Engine
• The graphics file is placed in a station.
• When ‘ Extract Die using Ink’ is selected, the die shape is extracted from the graphics.
If not, die shape is set to trim box.
• The CAD file is loaded and the outline of the CAD file is compared to the outline of the die shape generated in the above mentioned step. The graphics is rotated in such a way to create a maximal intersection of the CAD outline and the outline of the die shape. Any rotation is mentioned in the task's log file.
Note: In the
the CAD file is rotated and not the graphics.
• The CAD is taken as the die shape for the station.
• Limit Bleed: The bleed can be limited to a specific distance. The task create a bleed mask by spreading the die shape.
• Graphics for Backside: Select this to load a graphics file that will become the backside of the station file (also placed by external reference).
Note: Keep the following in mind about positioning graphics on the back side:
• If the PDF contains objects in the ‘die ink’, the graphics for the back side are positioned so that these objects are centered on the die of the front side.
• In the other case, the graphics on the back are positioned centered on the original borders of the front side graphics (i.e. not fitted).
• SmartMarks: Select this to load a SmartMarks set. Note that this one set will be used for both front and backside. Choose if you want to Add them to the current set or if they should Replace it.
When not Creating a Station file, the task creates a normalized PDF and the options are slightly different:
222
• The input file is opened and changed as requested (so it is not placed externally).
• The only options available are now:
• Fit Borders to Ink: Borders can be fitted to objects in a specific ink
•
Limit Bleed
• Placing SmartMarks.
Automation Engine
116
223
117
Automation Engine
117. Print
This task serves to print the input file on a PostScript printer that was configured on the
Automation Engine server. Mind that in this case, this configuration is not part of an Esko tool, but we mean the standard way to add printing devices on that Windows computer.
Attention: These devices should be configured on the server using the System
Account of Automation Engine. By default this is the local user BGSYSTEM, but you might have changed this (using the
'System Account' page in the Server Web tool
). The
Print task will not be available for devices configured by other users.
The task's settings are very similar to those explained in the page on the
task.
224
Automation Engine
118
118. Print IMP File
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
225
119
Automation Engine
119. Print on Digital Press
Important: This task is part of a workflow where it connects to a DFE (Digital Front End). We here distinguish 2 kinds of DFEs:
• the HP SmartStream Labels and Packaging Print Server Powered by Esko. In below pages, for sake of easy reading, we will name this the HP DFE.
• the Esko Inkjet DFE, a DFE serving several types of Inkjet digital presses.
Note: To see which version of the DFE engine software supports which version of Automation
Engine's Print on Digital Press task, check
http://www.esko.com/systemrequirements
.
Working with a DFE (Digital Front End) Server
Automation Engine can use files in its Containers to create Print Jobs on a DFE Server.
Automation Engine monitors those print jobs until they are printed on the digital press.
In Automation Engine:
• use the Print on Digital Press task to create print jobs on the DFE server.
• the Print on Digital Press (Track) task is started automatically and shows the status of the print jobs on that DFE server, also of print jobs that were not created via this task.
Both these tasks show detailed feedback for each step of the DFE printing process in the Pilot's
Tasks pane.
Setup
Before using those tasks, you must connect your Automation Engine server to your DFE server.
This is done in the
Configure panel (Digital Press)
.
Note: When your DFE server drives several digital presses, you also need to select the press to connect to.
119.1 Supported File Types
The task can send these file types to a digital press:
Note: 'Static' print jobs are print jobs that are not VDP jobs.
For 'Static' print jobs:
• Normalized PDF (selfcontained, so images embedded)
For Variable Data Print jobs:
• PDF/VT (for example generated by Adobe Illustrator, by using the Dynamic VDP Plug-in).
• VDT (Variable Data Template), also made in Adobe Illustrator, by using the Dynamic VDP plug-in.
226
Automation Engine
119
For 'Static' print jobs: For Variable Data Print jobs:
Note: This can be a oneup or an already stepped self-contained PDF.
• PDFPLA (Plato PDF)
Note: Before PDF/VT, the Print on Digital Press (PPML) task was used to have Automation Engine use PPML files to create variable print jobs on the DFE server. This task has been declared
'Soon Outdated'. Learn more in
Print on Digital Press (PPML) (Soon
Note: If your MIS system stores print job parameters in JDF format, you can add that JDF file to the input of the
Print on Digital Press task.
About Variable Data Printing
When using a VDT file to print a VDP job, the expansion of the variable data (using the Variable
Data Database) happens on the DFE. This is typically used when executing the expansion in
Adobe Illustrator or Automation Engine takes too much processing resources.
Note:
• A VDT file contains
VDP objects (placeholders for the variable data) and must be expanded to a PDF/VT file on the DFE server.
• A VDT file can be created with the Dynamic VDP DeskPack plug-in.
• Fonts used inside the VDT file must be installed on the DFE server.
119.2 Using the Print on Digital Press Ticket in a
Workflow
Unlike most workflow steps, the Print on Digital Press step does not create output files to be transferred to the next workflow step, but sends this output data to the DFE server.
This also means that this task step is always the final task in a workflow (branch).
In the workflow editor, you can see the number of files the task has successfully processed on its output pin called Inputs.
119.3 Print on Digital Press Task Settings
227
119
Automation Engine
Device: Choose the digital press you want to send your file to. This list contains all the digital presses that you
added in Configure
.
Print Job Ticket: Choose the print job ticket you have created on the DFE server to process and print jobs. In the list of tickets, notice the column indicating their Workflow Type:
Dynamic or Classic.
Note: When using the Print on Digital Press task, make sure the DFE server is running and that the Print Controller on the DFE is running. When your task is stuck, check if the Digital
Press connection is still OK (
in the Configure tool
).
Note: For all parameters in the below mentioned settings, you can choose the SmartName
[From Print Job Ticket] to use the parameter value defined in the selected DFE Print Job
Ticket.
The value that the SmartName finds in the chosen Print Job Ticket is then shown to the right of the input field. For example:
If you added a JDF file to the task input, you can choose [From JDF Ticket] to use the parameter value defined in your JDF file.
We now illustrate the settings in the tab sheets:
119.3.1 General Tab
228
Automation Engine
119
• Print Job Name: Keep the name if the input file or use a SmartName, Public Parameter or
Workflow Parameter to define a different one.
• Substrate: Shows the list of substrates available on the press.
• Copies: Enter the number of copies to be printed.
• Lead-in Sheets: Enter the number of Lead-in Sheets that need to be printed at the start of the print run, or select <None> in case you don't want to use any.
• Lead-out Sheets: Enter the number of Lead-out Sheets that need to be printed at the end of the print run, or select <None> in case you don't want to use any.
• Die Cut Layout Input Ink: Specify the ink of the input file of which its contents will be used for the lead-in/lead-out sheet. This is typically a technical ink (for example Cutter).
• Die Cut Layout Print Ink: Specify the ink that will be used to print the lead-in/lead-out sheets. This must be one of the inks of the selected Ink Set in the
tab.
Note: There is an exception to this rule for the HP DFE: since HP DFE 4.1/5.0 or higher, if you make a print job in CMY, you still can print in Black.
• Comments: Use SmartNames or choose Custom to enter print job related comments. They will be included with the file sent to the press, and become visible on the press's software panel (if your press model supports it).
119.3.2 Files tab
In this tab, you define the One-Ups. The available options depend on whether this is a Duplex
print or not.
For both part in this tab, you can choose Custom to define the settings here. Or you can choose [From JDF Ticket] to have them decided by an input JDF file.
About the Task Input Files and One-Ups
229
119
Automation Engine
• For pre-imposed PDFs or single-grid step and repeat files, only one file is needed to be added here as One-Up. If you are using multi-grid step and repeat, add here as many file entries as you will send to this task.
• In the Step and Repeat tab, you can map the here defined one-ups as input files for the desired grid of the template step and repeat.
• In the case you use VDT Files, you also need to define a Database file and optionally an
Image path.
Note: If the amount of the task's input files is not equal to the number of files specified in this
Files tab, you will get an error.
Here are some specifics per use case:
For a One Sided Print Job
For one sided print jobs, keep the
Duplex print option disabled. In the One Up settings, choose
custom.
For a Duplex Print Job
Note: Not all digital presses support duplex printing.
To create a duplex print job, select the option
Duplex print. Then define the
Backing Up mode:
• Select
Tumble if you want the roll to be re-inserted into the digital press with rewinding.
• Select Turn if you want the roll to be re-inserted into the digital press without rewinding.
The One-Up Settings list allows you to Custom specify an input file for both the Front and the
Back side of the print job.
With duplex print jobs, the same Database File and Image Path is used for the same grid for both Front and Back.
For a VDP Job
For VDP jobs, you also need to specify the source of the variable information. To do this, follow these steps:
1. In One-Up Settings, choose Custom.
2. Click Add.
3. In the field for the database file, click Select.
In the Select Database File dialog, your Source can either be a
• CSV File. This is used in case the job contains complex information such as names, serial numbers or links to images.
• Simple Database. In this case, you only use "Simple Counters". This is suited for jobs that only require a simple sequence of numbers. Define how many records need to be generated in the field Number of Records.
Learn more in the user documentation of your DFE.
Note: Creating a VDP print job from a VDT file is supported for Dynamic Workflows (for version support, check
http://www.esko.com/systemrequirements
).
230
Automation Engine
119
119.3.3 Step and Repeat Tab
Concept
The Step and Repeat Settings can be defined
• here, in this tab of this task. To do this, select Custom and read below how to define the settings. Disable the option Step and Repeat if you do not want to step and repeat.
• On the DFE, as part of the settings in the selected print job ticket. To do this, use the
SmartName [From Print Job Ticket]. The task then reads that DFE ticket and shows its settings here, in read-only mode.
• by a JDF input file, using the SmartName [From JDF Ticket].
Note: When using the PowerLayout DeskPack plug-in to send jobs to the DFE, you have already created your step and repeat, so that input file will here be considered as a one-up.
Defining the Type of Step and Repeat in this Ticket
When you enabled the option Step and Repeat and you selected custom in Step and Repeat
Settings, you can define Template based or Tabular layouts.
Creating a Template based Step and Repeat
If you want to step and repeat from a template, select one in the Template field.
Important:
• If you are working with multiple input files, you need to use a step and repeat template. You cannot define a tabular step and repeat.
• Template based step and repeat is only supported when using a Print Job Ticket of the
Workflow Type 'Dynamic'.
Note: Step and repeat templates and marks can be created in DeskPack (PowerLayout
Standalone & Dynamic Marks). Learn more on how to create these templates in the
DeskPack documentation
.
If your template has multiple grids and you have selected multiple one-ups in the Files tab, the task will automatically assign the first grid to the first one-up, etc. You can change this following
these steps:
231
119
Automation Engine
232
1. Select a grid either by clicking it in the Sheet Preview or by using the arrows in the Grid parameter.
2. In the list of One-Ups (that was specified in the files tab), select the one to go with this grid.
In this way you can assign the desired number of input files to a certain grid.
3. Repeat this for each grid and one-up you want to associate.
Note: If the number of one-ups does not match the number of grids in the template, or if the size of a one-up does not match the size defined in the template's grid, you will see a warning icon in the sheet preview.
The Grid Details tab will automatically be filled with the data of the selected grid from the template.
When working with duplex print jobs, you need to specify an input file in the
One-Up
parameter ( Files tab) for both front and back. See this example:
Automation Engine
119
Creating a Tabular Step and Repeat
This mode is available when you do not select a template. You can then specify all
Grid Details
in this ticket and you can optionally specify Variable Data settings.
on page 235.
Sheet Preview
The
Sheet Preview shows a preview of the result of your grid settings. You can also select grids by clicking on them in this preview.
Note: When you selected a template via a SmartName, the preview will not be available.
Adding Finishing Marks and Defining Margins
Indication of Grid/Template Size and Actual Repeat Area
233
119
Automation Engine
At the bottom of the dialog, you will see the Grid Size (if you defined a tabular step and repeat), or the Template Size (if you used a template). This includes the margins you defined in
.
The Actual Repeat Area shows the area actually used by the repetition, not including the margins. The width and length values are calculated based on the step and repeat parameters, including gaps. You cannot edit them.
Grid Details Tab
When you have only defined one One-up file in the Files tab, this is where you can define tabular step and repeat settings for that single one-up.
234
Note: If you are using a template, this tab will automatically be filled with data from the template (which is then non-editable).
Repeat one-up using its: Choose whether to use the dimensions of the one-up's Trim Box or
Media Box to calculate the repetition grid.
You can see the One-up Size on the right.
Clip on trim box with bleed of: Use this option to add bleed when clipping a one-up on the
Trim Box.
Note: This value should not be larger than half of the gap defined in the corresponding direction.
Orientation: Choose how to orientate the one-up.
Available Repeat Area: Define the width and length of the repeat area.
• The width can be set to Substrate Width (the width of the substrate you chose in the
Printing Properties) or to a Custom value.
• The length can be set to the Maximum Repeat Length or to a Custom value.
Repetition: This defines the number of horizontal and vertical steps in the repetition grid. You can choose either:
Automation Engine
119
• Maximum: The server will calculate the maximum amount of repetition steps possible within the Available Repeat Area.
• Custom: Enter the repetition amount of your choice.
Gaps: The values you enter here (for a horizontal and a vertical gap) will be used as a distance between the one-ups' borders in the repetition grid.
Note: For seamless printing, the top and bottom margin have to be equal to half of the vertical gap.
Variable Data Tab
Note: This tab can only be used when you are working on a variable print job (for this you need to have selected a Print Job Ticket of the Workflow Type 'Dynamic'.
Note: To send variable print jobs, the HP DFE needs to be version 4.0 or higher.
Use this tab to define how to distribute your variable data over the grid of one-ups that you built in the Grid details tab, or over the one-ups repeated according to the Template that you chose.
Start: Choose where to start printing your variable data (where to print the first record):
top left, top right, bottom left, bottom right.
The preview on the right shows a black dot representing the position of the first record.
For example, this distribution starts on the top left:
while this distribution below starts on the top right:
Choose also if the flow of variable data should run horizontally or vertically .
235
119
The preview on the right reflects your choice.
Horizontal flow:
Automation Engine
Vertical flow:
Note: The Printing direction marked with an arrow shows the direction that the paper flows through the press.
Note: When you selected a button via a SmartName, the preview will not be correct.
Fill over: Choose if you want to distribute the variable data over the Complete Job or over
Blocks.
If you choose Blocks, the variable data flow will run over Blocks of a certain size, then run over the next Block when the previous one is complete.
You can see an example of Blocks in the preview.
236
Block Size: You can define the size in Grid Rows, Sheets, Feet or Meters.
If you have chosen to Fill over the Complete Job, then the Block Size will be 1.00 Job by default.
Automation Engine
119
You can set it to another unit if you still want to print in Blocks, but without having the variable data flow respect the Block. This is useful if you want to add gaps (see below).
Add gap between blocks: This adds white space in between the Blocks. It is available when you have chosen to Fill over Blocks, or to fill over the Complete Job but still have Blocks (as explained above).
Gap size: This is available when you have selected Add gap between blocks. Define the gap size in Grid Rows, Sheets, Feet or Meters.
Marks and Margins
Click on Marks and Margins to add marks and margins to your output.
Note: You can also set marks and margins when you are not using step and repeat in your print job (when the Step and Repeat option at the top of the dialog is deselected).
Marks
Choose if you want to add Finishing Marks to your print job. Finishing marks are used to align the substrate for cutting. Select a set from the list or use [From Print Job] or any other
SmartName.
The list offers the marks that you made in 'Dynamic Marks' and, in case of an HP DFE, also the default marks 1 x LabelRow, 1 x Sheet or 2 x LabelRow.
Note: These marks are all visible when Step & Repeat is active, or from within PowerLayout.
When Step & Repeat is inactive, only 1 x Sheet is shown.
Note: If you are using a Step and Repeat template from the DFE, you can not add finishing marks here. The marks from the template will be applied.
Note: Second pass marks (also called "reinsertion marks") can not be controlled from
Automation Engine. Those can only be set on board the DFE ticket
Margins
237
119
Automation Engine
119.3.4 Transformation Tab
•
Vertical Scale: Use this to scale the print job vertically (in the length).
• Horizontal Scale: Use this to scale the print job horizontally (in the width).
• Rotation: Choose the rotation of the print job (None, 90˚ CW, 180˚ or 90˚ CCW).
Note: Rotation is disabled when Step and Repeat is enabled.
• Mirror: Choose whether or not to mirror the contents of the print job.
119.3.5 Color Management Tab
• Ink Set: Choose the set of process inks that will be generated by the RIP. The list depends on the press model.
• Use: Define if you want to use color management when RIP'ing the print job (to convert the file separations to the ink set used by the press), and what kind of color management.
238
You can define each margin (
1, 2, 3 and 4) using the following:
• Gap (Length or Width): The size of a gap between one-ups.
• Gap (Length or Width) / 2: Half the size of a gap between one-ups. This is typically used for top and bottom margins, as the bottom margin of one sheet plus the top margin of the next sheet will be equal to one gap.
• Custom: a custom number (formulas are not allowed).
Note: If you selected a finishing mark which size you defined in the DFE's configuration tool, the corresponding margin will show up as Defined by Mark.
This means that the margin is automatically large enough to provide space for this finishing mark. For example, if you, on a HP DFE, selected the default mark 1 x LabelRow, which is set in the DFE configuration tool to need 8 mm of right margin, the right margin ( 4) will be set to
Defined by Mark and be 8 mm wide.
Automation Engine
119
Choose <None> if you don't want to use any color management settings for this conversion.
• When you do want use color management here, select a Color Strategy from the list (or use a SmartName).
239
120
Automation Engine
120. Process PDF Spreads
Action
The ticket parameters depend on what type of Action you selected first.
• Split Reader Spread: To create single pages from an incoming spread.
• Make Reader Spread: To create spread pages from incoming single pages.
• Make Printer Spread: To create spread pages that can be used to create an imposition mock-up from incoming single pages.
Settings for 'Split Reader Spread'
•
Spread Position:
• Reference Box: Select a page box to choose how much of the page to include in, or retrieve from a spread. For example select Crop Box to crop everything outside that box.
• Offset: Enter an exact offset distance from the above selected reference box. The offset distance will extend beyond the box boundaries. This parameter is commonly used when creating spreads of asymmetric files.
• Bleed Mode: Control the placement and size of bleeds. Choose from:
• Remove Bleed: Only the content of the reference box will be kept, any bleeds present in the input file will be removed.
• Bleed from Bleed Box: The bleed will be the Bleed Box but only if the reference box is the Trim Box.
• Bleed from Bleed Distance: This adds the specified bleed distance to the chosen reference box. A bleed distance will extend beyond the borders of the Trim Box and therefore will set the boundaries of the Media Box when output.
•
Spread Structure:
•
Flow Direction: Determine whether pages are arranged in numerical order from either left to right or right to left. '
Left to Right' means that page one will be on the left hand side of a two-page spread, with the second page on the right. '
Right to Left' means page one will be on the right hand side of the spread, with page two on the left hand side.
• First Spread Contains: This controls how pages will be organized in the output file:
•
Page 1 and 2
To divide a spread into single pages. If you use this mode in conjunction with the
, you can split spread pages in a file while leaving single pages
intact.
Note: Note: The reference page for this splitting action using 'Mixed Spreads' should be a spread page, not one of the single pages.
•
First page only
240
Automation Engine
120
If you place the first page of the file on the right-hand side of the first spread page; the left-hand side remains blank.
For files with an even number of pages, the last page will be also be placed on a spread page, on the left-hand side, with an accompanying blank page.
The left / right positioning of pages on spreads is determined by the selection made in the field Flow Direction. The description above assumes a left to right flow direction.
•
Last and First page
In this mode, the last and first page of the input file are placed side by side on the first spread page.
In a left to right flow direction setting, the last page will be on the left and the first page on the right of the first spread page output.
In “Split Reader Spread” mode the task simply reverses the make mode. A file with spread pages will have the spread pages split but the page on the left side of the first spread will be output as the last single page of the output file.
•
Even number of pages
Use this to prevent input files with an even number of pages from losing any pages while being split.
The parameter produces different results depending on which of these spread types it is combined with.
• Select ' Even Number of Pages' together with the spread type 'First Page Only' to split the output file. The left side of the first spread and the right side of the last spread will not be output.
• A combination of the Last and First Page spread type and the Even number of
Pages parameter will split a file successfully.
Note: This option is active only when the Action 'Split Reader Spread' is selected and with spread types 'First Page Only' and 'Last and First Page'.
•
Mixed Spreads:
Use this option when you need to define the Reference page for input files that have various paper sizes.
For example, if a file contains both an A4 page as page one and a two-page spread as page two, enter page two as the reference page and indicate that this page has two pages on it.
All the spread pages are correctly detected and split correctly while leaving the single pages intact.
• Auto Detect Spread Reference: To take the most frequently featured page size as the
Reference page.
• Reference Page Number: To specify an exact page as the Reference Page. Use the actual page number in the series of pages, not the page’s number label.
• Reference Page contains X One-Ups: Enter the number of single pages to be positioned on the Reference Page.
241
120
Automation Engine
Settings for 'Make Reader Spread'
Select this Action to create spread pages from incoming single pages.
The options Spread Position and Spread Structure are the same as when you selected the
Action 'Split Reader Spread'.
Settings for 'Make Printer Spread'
Select this Action to create spread pages that can be used to make an imposition mock-up from incoming single pages.
The options Spread Position and Spread Structure are largely the same as when you selected the Action 'Split Reader Spread'.
242
Automation Engine
121
121. Proof (FlexProof)
In the Device list, select the FlexRip - Proofer Output item
that you added in the Configure tool
.
121.1 General
•
Transformations
• Scale V / H: Enter a percentage to scale the design vertically and/or horizontally (the V-H as you see the file in an editor or viewer).
•
Rotate: Choose a rotation (counter clockwise).
• Select Fit On Paper to fit the design on the paper of the selected proofing Device.
•
: Choose if you want a positive or negative output file.
•
: Choose if you want mirroring or not.
• Original Size (incl. Margins): The ticket shows the original size of the input file, margins included.
• Output Size (incl. Margins): The size shown here is the real output size, which is the original size influenced by the scaling factors, distortions and the rotation.
• Marks: If you want you can add SmartMarks to your file. SmartMarks sets are created in an Esko editor.
• Dot Gain Compensation:
• Single Curve: Select a Dot Gain Compensation Curve (*.dgc).
• Automatic: Select a screen based Dot Gain Curve (*.scrdgc or *.icpro).
121.2 Inks
• All inks: Deselect ‘All Inks’ to open the Inks list where you can select specific inks.
Attention: In FlexProof tickets, when you want a composite (proofing) output, be aware that de-selecting the 'All Inks' option will then output (proof) each selected ink separately.
• In the column ' Merge Ink with', you can manually decide which inks should be merged in the output file. This is common when you use different rulings of a same ink.
To do this, click in the column ' Merge Ink with' on the row of a specific ink and choose the other ink from the list that pops up. Or click on the name of the column if you want this change for all inks.
243
121
Automation Engine
Alternatively, click ' Merge Similar Inks' to let the task propose such combinations automatically for inks with a same name but with a different ruling or angle. Click
Reset
Merge to reset these settings and force the proofing of each ink separately.
• Use technical inks in output. Select this to include the inks with Ink Type 'Technical'.
• Keep similar inks in their original separations. Select this when you are create separated proofs and, instead of merging similar inks to one separation, you want each ink to print separately. This should not be selected for a composite proof.
• Keep inks separated. Do not merge the inks (enabled when you choose 'Separate' as
121.3 Advanced
• Hold In Rip Queue: Select this to keep the task in the RIP-queue on hold until someone manually releases it. Learn more in the page about the tool
Queue Monitor
.
• CT Resampling:
• Don’t resample: No re-sampling is done. This avoids most pixel shifts.
• Resample to highest CT resolution from job: Select this to fix the remaining pixel shift problems, with the least up-scaling possible without data loss.
• Resample to automatic chosen resolution: Select this to reduce broken dot problems, by interpolating images to at least 1.000 ppi.
• Resample to output resolution: This is the slowest option, re-sampling all CT's to the output resolution.
121.4 Pre-RIP
This tab is only relevant when some objects in the file need to be simplified before they can be sent to the RIP. The task takes this decision automatically. And even when this is done, the options are best left to their default settings.
These are the special objects in a Normalized PDF that require such pre-processing:
• ‘Edge vignettes’: vignettes with alpha channels effects on the edge of the object.
• Barco Blends: blend objects in the legacy 'GRO' format.
• Warped CTs: warping done on external CTs.
244
Automation Engine
121
Pre-RIP'ing creates an image (CT) of these special objects because the RIP can not interpret them.
• Specify the CT Resolution for these new images.
• Custom: This default choice of 304.8 ppi guarantees the behavior of previous Esko applications. This option is independent of the output resolution.
• Output: This creates the CTs at the same resolution as the RIP output resolution, with a maximum of 1.000 ppi. This option provides an optimal RIP output, but may slow down pre-RIP'ing and may require more disk space.
• Automatic: This create the CTs at a resolution as close as possible to 300 ppi, depending on the RIP output resolution. The task calculates it in such a way that the RIP output resolution is an integer multiple of this CT resolution.
• Anti-aliasing: Anti-aliasing smoothens the staircase effect that you get when an image is created of lineart objects.
• Vignette Noise: Some vignettes or parts of vignettes will be converted to CTs. This happens when they overlap other objects with translucency or overprint. To reduce the banding effect, noise is applied on the CT, also known as 'grain'. The amount of noise can be specified here.
• Blend to CT: Select this to convert legacy Barco Graphics blend objects into a CT.
• Smooth Blend: Select this to set the amount steps in the blend objects to 255. When
'Convert Blend Objects to CT' is activated and 'Smooth Blend' also, the generated CT will ignore the original steps of the legacy (Barco Graphics) blend object. The amount of steps is set at the maximum of 255.
• Resolve Transparency: Doing this as a pre-RIP stage can speed up the RIP'ing. Only select this when needed.
• Convert Strokes: Select this if your output device requires you to do so.
121.5 Output
• Configuration Set: Select a configuration file. These files represent specific behavior of the selected output device. The list is filtered according the CMS license that the selected Dispatcher holds. For example: if it has a license for 4 channels, no multi-channel configurations will be visible here.
• Output Folder: Leave this empty to use the output path as defined in the Dispatcher
('EskoLink queue' – 'Output' tab). If your EskoLink queue has no output path defined, you can then define an output folder here.
• Output File: Leave this empty to get an output file name based on the input file. Edit this to overrule this standard behavior. Only plain characters are allowed. Unsupported characters
(symbols) will be replaced by an _ .
• Output Type: Choose between
•
Composite (Colored and Greyscale)
• Separate (Colored and Black & White)
• Colored: All inks are converted to CMYK values
• Greyscale: All inks are converted to grey values
• Black and White: If you want a Black & White proof.
245
121
Automation Engine
• Anti-Aliasing: Anti-Aliasing smoothens the staircase effect you get in the generated CTs of lineart objects that need pre-processing.
• Define the Number of Copies you need.
• Select ' Keep job files for relaunch purposes' to be able to proof files again without having to RIP them again.
Note: The files created for the proof (and the proof job on the Esko Proof Client) will then have to be cleaned up manually.
•
White Coloring
Attention: You only see this option if one of your Configuration Sets connects to
an Epson Stylus Pro WT7900 proofer. See an example in
.
When you use an extra white ink to print on foil (transparent or metallic), this option allows you to customize your white ink (for example, to get a cooler or warmer white).
Choose between:
• No Coloring: This uses the proofer's white ink to print objects in the white separation, without applying coloring to this ink.
• Custom values: This allows you to color the proofer's white ink manually. Enter the
CMYK values to add to the white inks.
• Values from Color Management: This uses a Color Strategy to color the proofer's white ink. This Color Strategy must have a white Extra Output Ink (called white) and map the white separation used in the file to this white output ink.
121.5.1 Example: Color Managing White Ink for an Epson WT7900
Proof
For example, you want to print a file with an ink 'cool white' on your Epson Stylus Pro
WT7900 proofer.
1. In Color Engine Pilot’s Designer book: a) Add your file’s white ink (here 'cool white'), b) Add a generic white ink. Name it 'white'.
2. Create a Color Strategy that will color manage your file’s white ink: a) Add your generic white ink as an Extra Output Ink,
246
b) Map your file’s white ink (cool white) to your white output ink,
Automation Engine
121
c) Make sure Extra Output Ink and Ink Mapping are selected in your Color Strategy.
3. In the Proof (FlexProof) ticket, go to the Output tab and: a) select the Configuration Set corresponding to your Epson Stylus Pro WT7900 proofer, b) in White Coloring, select Values from Color Management.
4. In the ticket’s Color tab: a) select Manage Color, b) select Color Strategy, c) choose the Color Strategy with white ink mapping you created in Color Engine Pilot.
247
121
Automation Engine
121.6 Color
If you do want to
Manage Colors, then first select if this is for a
(simple) proof, or for
121.6.1 For Normal Proof
248
• When you select to Manage Color for Normal Proof, the settings of the requested color management are by default defined by the Color Strategy that you selected from the list.
When Color Strategy is not selected, the color management settings are entered with profile settings.
• Then, Use the Document Profile as Source Profile if Available is set but as this document profile may not be available, a backup of the source profile must still be chosen.
Choose the Process you want to simulate on the proof here. This process can be a registered ICC profile or an Esko Profile.
There are some default Esko Profiles on the system, for example crom_offs (Cromalin
Offset). If you have measured an Esko Profile yourself, for example for your own Flexo press, you will be able to select it here.
•
Destination Profile
This is the profile for the proofer. Choose the proofer profile that describes the colors of your proofer here (for example the characteristics of your proofer).
Both Esko Proofer profiles and ICC profiles of proofers are available in this list.
Also defaults are listed, for example ddcw_glossy, a description for a Digital Cromalin/
WaterProof on glossy paper.
If you profiled your proofer using Color Engine Pilot, you will be able to select your proofer profiles here as well.
Automation Engine
121
Note:
The list of color strategies and destination profiles is filtered according to the CMS license that the dispatcher holds.
If the Dispatcher has no CMS license, only “preview” and “linear” can be selected as color strategies, whereas additional strategies are available with a 4-channel or multi-channel license.
•
Rendering intent
• Relative (no background): Choose this if you do not want any background simulation.
The white point of the source will be mapped on the white point of the destination process. This rendering intent takes into account the ability of the human eye to adapt to the surrounding white.
• Absolute (background): Choose this if you want background simulation and you want an exact color match, including the paper simulation.
• Perceptual: This will result in no background simulation (white of reference color space is mapped on white of destination color space). Choose this when you don't care too much about an exact color match but when want the pictures at least to look nice on your proofer. It will give a visually pleasing result. If the gamut of the source is wider than the proofer, the entire gamut is shrunk so that it fits inside the gamut of the proofer.
• Saturation: Choose this if you care especially about saturated colors. This rendering intent will map saturated colors on saturated colors.
•
Black Mapping
This option is only available if you choose an Esko destination profile. Black will be mapped onto black or, in other words, the black separation will only be printed with black ink.
In case you want to simulate a very dark black, which is darker than the black of your proofer, you might want to deselect this option. In this case all 4 proofer inks will be used to simulate the high density of the black.
•
Handling Unregistered Inks
Unregistered inks are inks that are not present in your color management database. They cannot be color managed which means that you cannot proof them accurately.
proofing.
Choose what to do in case some unregistered inks are still in the list of inks to be proofed:
• Deselect ' Generate an error if the job contains unregistered inks' if you want the task to end with a warning. All the inks you chose to include in the output will be proofed, but the unregistered inks will not be color accurate.
• Select ' Generate an error if the job contains unregistered inks' if you want the task to end in error.
In both cases, you will also see a message in the log.
249
121
Automation Engine
Note: When you select an Equinox source profile (or use a Color strategy with Equinox source profile) with ' Manage color toggle selected, this task will perform a default check. This check verifies if all the selected inks in the file are specified in the Equinox source profile. If they are not specified, the task will end in error with a message such as: "Proofing aborted because the following input inks are not found in the source profile: glue cut"
121.6.2 For Emulation Proof
Attention: You need an extra license to see this option.
250
In this mode, CMS options can be set twice:
• In the top section of the tab, you set the color management options for emulating the conventional press on a digital press (conversion from the Source Profile to the Emulation
Profile).
• In the bottom section, you set the color management options for the output proofing device
(conversion from Emulation Profile to Destination Profile).
The preferred method is to use a Color Strategy for both conversions. Select the emulation
Color Strategy first, so that the list of color strategies for the output settings can be filtered to have the same source profile as the emulation profile selected in the emulation step.
Alternatively, you can manually select the source profile, emulation profile and destination profiles with their respective rendering intents.
Automation Engine
121
Tip:
If you select a multichannel printing profile in the Emulation Profile list (such as the sevenchannel IndiChrome Plus profile), you can use the button Output Inks... to enable or disable the additional inks (for example, indiChr Orange, indiChr Green, and indiChr Violet).
This allows you to use a profile like IndiChrome Plus to generate output without one or more of the additional inks (for example, without the IndiChrome Orange ink).
Handling Unregistered Inks
Unregistered inks are inks that are not present in your color management database. They cannot be color managed which means that you cannot proof them accurately.
Therefore, we recommend you
, especially for contract proofing.
Choose what to do in case some unregistered inks are still in the list of inks to be proofed:
• Deselect ' Generate an error if the job contains unregistered inks' if you want the task to end with a warning. All the inks you chose to include in the output will be proofed, but the unregistered inks will not be color accurate.
• Select ' Generate an error if the job contains unregistered inks' if you want the task to end in error.
In both cases, you will also see a message in the log.
Note: When you select an Equinox source profile (or use a Color strategy with Equinox source profile) with ' Manage color toggle selected, this task will perform a default check. This check verifies if all the selected inks in the file are specified in the Equinox source profile. If they are not specified, the task will end in error with a message such as: "Proofing aborted because the following input inks are not found in the source profile: glue cut"
121.7 Verification
Note: You can only set Verification options if you have chosen an Esko Proof Configuration
Set in the Output tab.
Print Verification Strip: To print a verification strip, select this option and fill in the options that become available.
Strip Preset: A certain number of presets come with your color database. They contain information about the strip and the measurement device to use, the tolerances in color difference, etc.
You can select a preset here, that will fill in the options below, or you can select Custom and fill the options in yourself. You can also start from a preset and change the other options (the
Strip Preset field will then show Custom).
Learn more about strip presets in the
FlexProof/E documentation
.
In Strip Type, choose between EskoStrip or Esko + Solid Color Strip. The 'Esko + Solid Color
Strips' contain the same patches as the 'EskoStrips', plus a 100% patch for every spot color present in the job. When printing a color managed strip, you should use an 'Esko + Solid Color
Strip'.
Learn more about available strips in the
FlexProof/E documentation
.
251
121
Automation Engine
Apply Color Management to Strip: If you selected Manage Color in the Color tab, the Apply
Color Management to Strip option is available. Select it if you want to color manage the strip.
Verify strip (with Verification tool): This option is available if you have a Verification license and if you are color managing your file. Choose what to use as a Reference for this verification:
• Choose ' Manually load reference values' if you want to verify the color managed strip against a standard (for example Ugra/Fogra) or a previous measurement.
You will need to load this standard manually in the Esko Verification tool.
• Choose ' Automatically load reference values from source profile' if you want to verify the color managed strip against the source ICC profile (set in the Color Strategy used or defined in the Color tab).
dE Formula: Choose the Delta E formula to use when verifying your strip. Choose dE CIE76,
dE CMC, dE 94 or dE 2000. If your company is already using one of those standards, we recommend that you choose the same one. If not, you should choose the most recent one: 'dE
2000'.
Click Edit Tolerances... to set custom tolerances for the measurements. You can fill in:
• General dE Limits: The 'Delta E' values that the color patches and paper should not exceed.
• Primary color dE Limits: The maximum 'Delta E' values allowed for CMYK colors.
• Hue difference Tolerance Limits: The maximum 'Delta H' values for CMYK, CMYKRGB and grayscale colors.
Note: 'Delta H' is the difference in hue between the expected color and the printed color.
•
Tone Value Tolerance Limits
Note: 'Delta T' is the difference in colorimetric tone value between the colors.
•
Chromaticness Tolerance Limits
Note: 'Delta F' is the difference in saturation (or "chroma") between the colors in your file and the printed colors.
If you selected a Strip Preset, the tolerances may be automatically defined.
The verification will pass if the Delta E values are within the tolerances, or fail if they are bigger.
Strip Layout: Learn more in the
Pack Proof documentation
.
252
Automation Engine
122
122. Proof for Contract Approval
This task is part of the Pack Proof product. Learn more in the
user guide of Pack Proof
. .
253
123
Automation Engine
123. Proof for Content Approval
This task is explained in the chapter on
Imaging Engine
. Find a direct link
here
.
254
Automation Engine
124
124. Proof IMP File (FlexProof)
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
255
125
Automation Engine
125. Proof to File - Unscreened
This task is documented in the chapter on
Imaging Engine
. Find a direct link
here
.
256
Automation Engine
126
126. Publish Imposition on WebCenter
Chain
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
257
127
Automation Engine
127. Publish On WebCenter
This task is documented in the chapter Integrating with WebCenter. Find a direct link
here
.
258
Automation Engine
128
128. Relocate Job
This task is documented in the
separate chapter on Jobs
. Find a direct link
here
.
259
129
Automation Engine
129. Remove Job
This task is documented in the
separate chapter on Jobs
. Find a direct link
here
.
260
Automation Engine
130
130. Remove Product
This task is documented in the
separate chapter on Products
. Find a direct link
here
.
261
131
Automation Engine
131. Resize PDF for Output
This task allows to resize a PDF's pages or its contents before output to a proofer or RIP.
Output Page Size:
• Select ' Resize to a specific page size' to adjust the PDF markup for a given paper size.
• Deselect it if you only want to adjust the page contents (page boxes, etc.).
This option affects which parameters you see in Page Size and Page Content:
131.1 Resizing to a Specific Page Size
When Resize to a specific page size is selected, you have these options:
1. In the Page Content area, select the Page Box to Use for positioning, scaling, etc.
2. Select how to Position this page box and its contents on the page:
• Don’t Fit: The file is placed “as is”.
• Center on Page: The file is centered in the selected page box.
• Scale to Fit (Reduce Only): The task scales the file down if necessary, so it fits in the selected page box.
• Scale to Fit (Reduce & Enlarge): The task scales the file up or down if necessary, so it fits in the selected page box.
• Scale to Fit (Disproportional): The task disproportionally scales the file up or down if necessary, so that it fits in the selected page box.
• Use Proportional Tiling: The task tiles the file over several pages as necessary, but make all tiles the same size.
• Gripper on Top: The task leaves space for the gripper at the top of the page.
• Gripper at the Bottom: The task leaves space for the gripper at the bottom of the page.
When selecting Use Proportional Tiling, you can enter the size of the Tile Overlap (where two tiles are partly on top of each other).
When selecting Gripper on Top / Bottom, enter the amount of space needed for the gripper in Gripper Size.
3. Mirror page mirrors the page contents and the page boxes horizontally.
4. If you want, use the Scale parameter to scale the artwork before placing it on the page.
5. If you want, enter a Horizontal and/or a Vertical Distortion to apply to the artwork before placing it on the page.
You can either enter the distorted output values (for example 97% or 103%), or the positive/ negative distortion values (for example -3% or +3%).
6. Select Clip on selected page box to clip away all artwork outside the page box that you selected in Page Box to Use.
262
Automation Engine
131
Note: The artwork outside the selected page box is not deleted, just clipped away by a clipping path (it is invisible but still present in the file).
7. Select Crop to fit if you want to crop your Page Box to the content of your original file.
8. In the Page Size area, select the page size you intend to print to in New Page Size.
This page size is used by the Scale and Position parameters.
• If you select a predefined page size, the option Orientation allows to select the orientation of the paper that you intend to use. Choose either Portrait or Landscape.
• If you select Custom as a page size, you will see a Page Width and a Page Height fields where you can enter the dimensions of the custom paper you intend to use.
9. Enter the Page Margins required by the output device.
The Page Margins value is used for the four sides of the page. These margins cannot be used for exposing.
131.2 Not Resizing to a Specific Page Size
If you don't select Resize to a specific page size, you can resize or reposition the PDF contents:
1. In the Page Content area, select the Page Box to Use for positioning, scaling, etc.
2. Select Center content on page if you want to center the page contents on the page.
3. Select Mirror page if you want to mirror the page contents horizontally.
4. If you want, use the option Scale to define a scaling to apply to the artwork before placing it on the page.
5. If you want, enter a Horizontal and/or a Vertical Distortion to apply to the artwork before placing it on the page.
You can either enter the distorted output values (for example 97% or 103%), or the positive/ negative distortion values (for example -3% or +3%).
6. In the Page Size area, use the option Set Orientation to alter the orientation of every page without resizing it. Choose between Keep, Portrait or Landscape.
7. Use the options Rescale page boxes and Rescale page size to define what happens when you scale the page contents: a) Select Rescale page boxes to scale the page boxes together with the contents.
Deselect it to only scale the page contents and not the page boxes.
b) Select Rescale page size to scale the page size together with the contents.
263
131
Deselect it to only scale the page contents and not the page size.
Automation Engine
264
Automation Engine
132
132. Resolve OPI
This task serves to replace the low-resolution images in a PDF with their high-resolution versions that the PDF links to via OPI comments.
Repository tab
• Add the location(s) of the external folder(s) that contain(s) the OPI-files.
• If necessary, add the location(s) of the excluded folders. These folders will not be searched.
Note: Use this option if all images can be found on the same volume and you want to exclude all folders containing low-resolution files.
• Select ' Update OPI links only' to only update the links to the high-resolution images and to not replace the links by embedding the high-resolution images.
Mapping tab
You can here specify a list of how file extensions should be mapped:
• Click Add and enter the original extension in the From field. If left blank, the extension in the To field will be applied to all linked files.
• In the To field, enter the new extension to give the linked files, or a comma-separated list of extensions to use as replacement for the original extension.
Note: If you enter multiple extensions, the task searches for a file matching one of them.
Use the backslash ( \ ) to preserve a character (for example to use a comma as part of an extension and not as a separator).
265
133
Automation Engine
133. Restore Job
This task is documented in the
separate chapter on Jobs
. Find a direct link
here
.
266
Automation Engine
134
134. RIP IMP File to Screened and
Unscreened Tiff File
This task is described in the separate document "Commercial Print (Page) workflows in
Automation Engine". Find it next to this "Complete Manual" on
https://www.esko.com/Support/
Product?id=Automation%20Engine
.
267
135
Automation Engine
135. RIP to CDI LEN File
This task requests a FlexRip/C to create LEN files for a CDI.
First select the Device you added in
the Configure tool
(a FlexRip/C) .
This task has five tabs:
• General (see the
same tab in the task 'RIP to Screened Tiff File'
)
• Inks (see the
same tab in the task 'RIP to Screened Tiff File'
)
• Advanced (see the
same tab in the task 'RIP to Screened Tiff File'
)
•
same tab in the task 'RIP to Screened Tiff File'
•
135.1 Output
Note: Parameters that have been specified in the Dispatcher Queue Settings are enforced in this ticket. Some are preceded by an icon of a Dispatcher: .
268
•
Configuration Set
• Name: Select a configuration file. These files contain specific behavior of the output device.
• Plate Size: The plate size of the above selected configuration set is shown.
•
Output File
• Path: Leave this empty to use the path as defined in the Dispatcher (EskoLink queue -
Output tab). If the EskoLink queue has no value for this path, you can define it here.
• Name: Leave this empty to get output file names based on the input file. The default output file name is [File]_[PageNrOfMultiPageFile]_[ShortInkName].
When changing this, be aware that only plain letters and numbers are allowed. Any unsupported characters (symbols) will be replaced by an _ .
Automation Engine
135
• Resolution of the output file:
• Perimeter: When a configuration set is chosen, this field is grayed out and shows the CDI's 'perimeter' that was set in the device queue (in
the Configure tool
). When no configuration is chosen, you can edit this field.
• Pixelclock: Choose the appropriate Pixelclock of your CDI. This field will most probably be fixed as it does read what CDI type your device queue was based on (in
the Configure tool
).
Note: CDIs with ‘VariablePLL’ will not show the Pixelclock field nor the Perimeter field.
• Actual resolution: This field shows the actual resolution that will be used by the RIP.
This is the combination of the requested resolution and the effect of the perimeter on that requested resolution.
Note: The FlexRip rounds off any non-integer number (see the task's log file).
• Compression: Choose the compression method for the output files.
The LZW compression is most commonly used. CCIT group compressions are more effective but take longer to generate (and to decompress on the receiving side).
269
136
Automation Engine
136. RIP to Screened and Unscreened DCS
File
Select a Device that was configured in
the Configure tool
.
This task has five tabs:
• General (see the
same tab in the task 'RIP to Screened Tiff File'
).
The ticket to RIP to an unscreened DCS file does not show the screening options.
•
• Advanced (see the
same tab in the task 'RIP to Screened Tiff File'
).
•
same tab in the task 'RIP to Screened Tiff File'
•
Note: Parameters that have been specified in the Dispatcher Queue Settings are enforced in this ticket. Some are preceded by an icon of a Dispatcher: .
136.1 Output
Note: Parameters that have been specified in the Dispatcher Queue Settings are enforced in this ticket. Some are preceded by an icon of a Dispatcher: .
270
•
Configuration Set
•
Name: Select a configuration file. These files contain specific behavior of the output device.
• Plate Size: The plate size of the above selected configuration set is shown.
•
Output File
Automation Engine
136
• Path: Leave this empty to use the path as defined in the Dispatcher (EskoLink queue -
Output tab). If the EskoLink queue has no value for this path, you can define it here.
• Name: Leave this empty to get output file names based on the input file. The default output file name is [File]_[PageNrOfMultiPageFile]_[ShortInkName].
When changing this, be aware that only plain letters and numbers are allowed. Any unsupported characters (symbols) will be replaced by an _ .
• Select a Resolution for the output files.
Single File DCS: When selected, all separations are first RIP'ed to separate files and then included in a final single DCS file (in the end only one file is created). When not selected, a
DCS master file is created that refers to plate files, one for each separation.
• Compression: Choose the compression for the output TIFF files: Flate, LZW or CCITT Group.
The LZW compression is most commonly used. CCIT group compressions are more effective but take longer to generate (and to decompress on the receiving side).
• Preview: Define the type and resolution of the preview files:
• For Placement Only: To use in a DTP application.
• Proofable Preview: For composite printing from a DTP application.
136.2 Inks
• All inks: Deselect ‘All Inks’ to open the Inks list where you can select specific inks.
Attention: In FlexProof tickets, when you want a composite (proofing) output, be aware that de-selecting the 'All Inks' option will then output (proof) each selected ink separately.
• In the column ' Merge Ink with', you can manually decide which inks should be merged in the output file. This is common when you use different rulings of a same ink.
To do this, click in the column ' Merge Ink with' on the row of a specific ink and choose the other ink from the list that pops up. Or click on the name of the column if you want this change for all inks.
Alternatively, click ' Merge Similar Inks' to let the task propose such combinations automatically for inks with a same name but with a different ruling or angle. Click
Reset
Merge to reset these settings and force the proofing of each ink separately.
271
136
Automation Engine
• Use technical inks in output. Select this to include the inks with Ink Type 'Technical'.
• Keep similar inks in their original separations:
• Keep inks separated: When 'All inks' is selected, select this to avoid merged inks.
• Select ' Highlight modified values' to have all modified values highlighted and marked with an asterisk.
272
Automation Engine
137
137. RIP to Screened and Unscreened PDF
File
Select a Device that was configured in
the Configure tool
.
This task has five tabs:
• General (see the
same tab in the task 'RIP to Screened Tiff File'
). The ticket to RIP to unscreened PDF does not show the screening options.
• Inks (see the
same tab in the task 'RIP to Screened Tiff File'
)
• Advanced (see the
same tab in the task 'RIP to Screened Tiff File'
)
•
same tab in the task 'RIP to Screened Tiff File'
•
Note: The fields in gray are the presets that are defined in the Dispatcher Queue settings.
137.1 Output
Note: Parameters that have been specified in the Dispatcher Queue Settings are enforced in this ticket. Some are preceded by an icon of a Dispatcher: .
•
Configuration Set
• Name: Select a configuration file. These files contain specific behavior of the output device.
• Plate Size: The plate size of the above selected configuration set is shown.
273
137
Automation Engine
•
Output File
• Path: Leave this empty to use the path as defined in the Dispatcher (EskoLink queue -
Output tab). If the EskoLink queue has no value for this path, you can define it here.
• Name: Leave this empty to get output file names based on the input file. The default output file name is [File]_[PageNrOfMultiPageFile]_[ShortInkName].
When changing this, be aware that only plain letters and numbers are allowed. Any unsupported characters (symbols) will be replaced by an _ .
• Select a Resolution for the output files.
• Anti-Aliasing (option appears when RIP'ing to unscreened files): Anti-Aliasing smoothens the staircase effect you get in the image data generated from line-art objects that need preprocessing.
• PDF Version: Choose a version:
• PDF for Illustrator: Select this version if the PDF 1.4 file will be opened in Adobe
Illustrator CS2 or higher. Because Adobe Illustrator only supports an undocumented subset of PDF 1.4 features, some objects and/or color-spaces must be split up, transformed and/or pre-RIP'ed in order to correctly represent them in Illustrator.
•
PDF/X-1 a:2001 (ISO 15930-1)
•
PDF/X-3 - (ISO/DIS 15930-2)
• PDF 1.4 - Acrobat 5.0.
•
Single / Multi File
When selecting 'single file' output, all separations are first RIP'ed to separate files first and then included in the final PDF / PS file. When this option is not selected, the task creates a
Master file and also plate files that it refers to (one per separation).
•
Softproofing
When selected, the task writes a composite PDF file that combines the different separations in a single PDF page. This PDF file can be used for colored viewing in Acrobat.
The combination of 'Single file' with 'Softproofing', can lead to four situations:
• No soft-proofing, multi file: All separations are written in a different page, and all pages are written in a separate output file.
• No soft-proofing, single file: All separations are written in a different page, and all pages are combined in a single file.
• Soft-proofing, multi file: Separations are kept together per page, and all pages are written in a separate output file.
• Soft-proofing, single file: Separations are kept together per page, and all pages are combined in a single file.
• Compression: Choose a compression method.
•
Encoding
• Binary: The image data is represented as binary data. This results in compact files. Such files are not editable in a common ASCII editor. Nor can these files be transferred using a communication protocol that relies on control characters in the data stream itself.
274
Automation Engine
137
• Hex: This forces the output to remain editable with an ASCII editor. It can then also can be transferred using whatever communication protocol is available. The drawback is that hexadecimal image data can take up to twice as much size as binary data.
• ASCII 85: Encodes binary data in an ASCII base-85 representation. This encoding uses nearly all of the printable ASCII characters. The resulting expansion factor is 4:5, making this encoding more efficient than hexadecimal.
275
138
Automation Engine
138. RIP to Screened and Unscreened
PostScript File
Select a Device that was configured in
the Configure tool
.
This task has five tabs
• General (see the
same tab in the task 'RIP to Screened Tiff File'
). The ticket for unscreened output does not show any screening options.
• Inks (see the
same tab in the task 'RIP to Screened Tiff File'
)
• Advanced (see the
same tab in the task 'RIP to Screened Tiff File'
)
•
same tab in the task 'RIP to Screened Tiff File'
•
138.1 Output
Note: Parameters that have been specified in the Dispatcher Queue Settings are enforced in this ticket. Some are preceded by an icon of a Dispatcher: .
276
•
Configuration Set
• Name: Select a configuration file. These files contain specific behavior of the output device.
• Plate Size: The plate size of the above selected configuration set is shown.
•
Output File
• Path: Leave this empty to use the path as defined in the Dispatcher (EskoLink queue -
Output tab). If the EskoLink queue has no value for this path, you can define it here.
• Name: Leave this empty to get output file names based on the input file. The default output file name is [File]_[PageNrOfMultiPageFile]_[ShortInkName].
Automation Engine
138
When changing this, be aware that only plain letters and numbers are allowed. Any unsupported characters (symbols) will be replaced by an _ .
• Select a Resolution for the output files.
• Anti-Aliasing (option appears when RIP'ing to unscreened files): Anti-Aliasing smoothens the staircase effect you get in the image data generated from line-art objects that need preprocessing.
•
Single / Multi File
When selecting 'single file' output, all separations are first RIP'ed to separate files first and then included in the final PDF / PS file. When this option is not selected, the task creates a
Master file and also plate files that it refers to (one per separation).
• Compression: Choose a compression method.
•
Encoding
• Binary: The image data is represented as binary data. This results in compact files. Such files are not editable in a common ASCII editor. Nor can these files be transferred using a communication protocol that relies on control characters in the data stream itself.
• Hex: This forces the output to remain editable with an ASCII editor. It can then also can be transferred using whatever communication protocol is available. The drawback is that hexadecimal image data can take up to twice as much size as binary data.
• ASCII 85: Encodes binary data in an ASCII base-85 representation. This encoding uses nearly all of the printable ASCII characters. The resulting expansion factor is 4:5, making this encoding more efficient than hexadecimal.
277
139
Automation Engine
139. RIP to Screened and Unscreened Tiff
File
Select a Device that was configured in
the Configure tool
.
Note: Options that are grayed out are values that were already defined in the Dispatcher queue settings.
139.1 General
278
•
Transformations
• Scale V / H: Enter a percentage to scale the design vertically and/or horizontally (the V-H orientation is the one that you see when the file is opened in an editor or viewer).
• Rotate: Choose a rotation (counterclockwise).
• Shrink: Use values from file: When the input file is a Plato file that has shrink values defined inside the PDFPLA file, it will show these values here. Deselect this option to edit and overrule those values.
Attention: If you use both scaling and shrink (distortion) options, then both these scaling values will be executed! For example: If your ticket requests a shrink
V 98% but also a Scale V 95%, then the output-size for V will be 98% of 95% (which is 93.1 %). So the file is first scaled and then distorted.
•
: Choose if you want a positive or negative output file.
•
: Choose if you want mirroring or not.
Automation Engine
139
• Original Size (incl. Margins): The ticket shows the original size of the input file, margins included.
• Output Size (incl. Margins): The size shown here is the real output size, which is the original size influenced by the scaling factors, distortions and the rotation.
• Marks: If you want you can add SmartMarks to your file. SmartMarks sets are created in an Esko editor.
• Screening (in tickets for screened output):
• Type: Choose the type of screening.
• Dotshape: Choose a dot shape. When dot shapes were defined in your input file, you can use those by choosing ' JOB → (Dotshape(s) as defined in File)'. This option will display in orange when the input file does not have any predefined dots (in its ink menu).
Attention: When a dot shape is displayed in orange, you can select it but the
RIP's default dot shape will be used instead.
•
Dot Gain Compensation
• Single Curve: Select a Dot Gain Compensation Curve (*.dgc).
• Automatic: Select a screen based Dot Gain Curve (*.scrdgc or *.icpro).
• Platemaking DGC: This displays the platemaking DGC (if any) defined in the FlexRip
Configurator tool.
Tip: The compensations are also applied to the SmartMarks. To prevent this, consider using specific inks or rulings for the inks used in your SmartMark objects.
139.2 Inks
• Inks on separate TIFF files: This option only appears when you're outputting to a merging device (as defined in the Configure tool). Select it to make sure that different inks end up on different films.
279
139
Automation Engine
• All inks: Deselect ‘All Inks’ to open the Inks list where you can select specific inks.
Attention: In FlexProof tickets, when you want a composite (proofing) output, be aware that de-selecting the 'All Inks' option will then output (proof) each selected ink separately.
• In the column ' Merge Ink with', you can manually decide which inks should be merged in the output file. This is common when you use different rulings of a same ink.
To do this, click in the column ' Merge Ink with' on the row of a specific ink and choose the other ink from the list that pops up. Or click on the name of the column if you want this change for all inks.
Alternatively, click ' Merge Similar Inks' to let the task propose such combinations automatically for inks with a same name but with a different ruling or angle. Click
Reset
Merge to reset these settings and force the proofing of each ink separately.
• Use technical inks in output. Select this to include the inks with Ink Type 'Technical'.
•
Keep similar inks in their original separations
•
Keep inks separated: When 'All inks' is selected, select this to avoid merged inks.
• Select ' Highlight modified values' to have all modified values highlighted and marked with an asterisk.
139.3 Advanced
280
Automation Engine
139
• Hold In RIP Queue: Select this to hold the task in the RIP-queue until someone manually releases this task.
• Yellow Ruling:
• Don't change Y ruling: The ruling of the yellow ink is not adapted.
• Change Y ruling: Choose from: -15%, -7%, 0% (no change), + 7% and +15%.
• Change Y ruling stochastic: Same as above but the dot shapes are also adapted to the
Monet dot.
•
CT Resampling:
• Don’t resample: No re-sampling is done. This avoids most pixel shifts.
• Resample to highest CT resolution from job: Select this to fix the remaining pixel shift problems, with the least up-scaling possible without data loss.
• Resample to automatic chosen resolution: Select this to reduce broken dot problems, by interpolating images to at least 1.000 ppi.
• Resample to output resolution: This is the slowest option, re-sampling all CT's to the output resolution.
139.4 Merge Queue
This tab appears when the configuration of the selected Device has the "Merge' function on
' Yes' (see its setting in the
Configure tool
).
Note: 'Merging' here means making an optimized layout of separations next to each other.
• Merge with other jobs: Select this to merge the separations that this ticket creates with separations from other files that were also RIP'ed for this FlexRip device.
• Hold in Merge Queue: This will ‘hold’ the separations in the merger database. This means they are ‘not to be considered for merging’. Use the tool "
Merger Monitor
" to see this database and to manually release entries that were put on hold.
• Force after: Separations that were put on hold can automatically be released again after a chosen time. This prevents having to wait too long before the ‘ Minimum Fill %’ has been reached. Learn more in
FlexRip - Screened Output
.
•
Priority: Define the priority that entries will have in the merger database. Entries with a high priority will be chosen sooner for merging with other entries.
281
139
Automation Engine
• Restriction: The separations will only merge with other separations of files that have received the same restriction value from this field. This value can be anything, whatever makes sense for your workflow. Some examples:
• fruit: The word 'fruit' could be used to make sure that these separations will only be merged with other separations that were also sent with that word 'fruit'. The goal could be that you wish to merge the separations of the 'banana', 'cherry' and 'apple' jobs all on the same film.
• Bob. The word 'Bob' could be operator Bob's restriction to only get films with separations of 'his own jobs'.
139.5 Pre-RIP
282
This tab is only relevant when some objects in the file need to be simplified before they can be sent to the RIP. The task takes this decision automatically. And even when this is done, the options are best left to their default settings.
These are the special objects in a Normalized PDF that require such pre-processing:
• ‘Edge vignettes’: vignettes with alpha channels effects on the edge of the object.
• Barco Blends: blend objects in the legacy 'GRO' format.
• Warped CTs: warping done on external CTs.
Pre-RIP'ing creates an image (CT) of these special objects because the RIP can not interpret them.
• Specify the CT Resolution for these new images.
• Custom: This default choice of 304.8 ppi guarantees the behavior of previous Esko applications. This option is independent of the output resolution.
• Output: This creates the CTs at the same resolution as the RIP output resolution, with a maximum of 1.000 ppi. This option provides an optimal RIP output, but may slow down pre-RIP'ing and may require more disk space.
• Automatic: This create the CTs at a resolution as close as possible to 300 ppi, depending on the RIP output resolution. The task calculates it in such a way that the RIP output resolution is an integer multiple of this CT resolution.
• Anti-aliasing: Anti-aliasing smoothens the staircase effect that you get when an image is created of lineart objects.
• Vignette Noise: Some vignettes or parts of vignettes will be converted to CTs. This happens when they overlap other objects with translucency or overprint. To reduce the banding
Automation Engine
139 effect, noise is applied on the CT, also known as 'grain'. The amount of noise can be specified here.
• Blend to CT: Select this to convert legacy Barco Graphics blend objects into a CT.
• Smooth Blend: Select this to set the amount steps in the blend objects to 255. When
'Convert Blend Objects to CT' is activated and 'Smooth Blend' also, the generated CT will ignore the original steps of the legacy (Barco Graphics) blend object. The amount of steps is set at the maximum of 255.
• Resolve Transparency: Doing this as a pre-RIP stage can speed up the RIP'ing. Only select this when needed.
• Convert Strokes: Select this if your output device requires you to do so.
139.6 Output
Note: Parameters that have been specified in the Dispatcher Queue Settings are enforced in this ticket. Some are preceded by an icon of a Dispatcher: .
•
Configuration Set
• Name: Select a configuration file. These files contain specific behavior of the output device.
• Plate Size: The plate size of the above selected configuration set is shown.
•
Output File
• Path: Leave this empty to use the path as defined in the Dispatcher (EskoLink queue -
Output tab). If the EskoLink queue has no value for this path, you can define it here.
• Name: Leave this empty to get output file names based on the input file. The default output file name is [File]_[PageNrOfMultiPageFile]_[ShortInkName].
When changing this, be aware that only plain letters and numbers are allowed. Any unsupported characters (symbols) will be replaced by an _ .
• Select a Resolution for the output files.
• Compression : Choose the compression for the output TIFF file. Which compression to use depends on the device you are creating the TIFF files for.
283
139
Automation Engine
The LZW compression is most commonly used. CCIT group compressions are more effective but take longer to generate (and to decompress on the receiving side).
284
Automation Engine
140
140. Router
This Workflow Control is documented in the chapter
"Workflows"
. Learn more in
Router
.
285
141
Automation Engine
141. Run ArtiosCAD Standard
This task creates an ArtiosCAD ARD design based on an existing standard.
This task is set up by an Esko Solution Architect.
To learn more, search for online articles on this topic in the
Esko Knowledge Base
.
286
142. Run Script
This task is documented in the chapter
Using Scripts
. See
The Run Script Task
.
Automation Engine
142
287
143
Automation Engine
143. Select File
This Workflow Control is documented in the chapter
"Workflows"
. Learn more in
Select File
.
288
Automation Engine
144
144. Select Mark File
This Workflow Control is documented in the chapter
Workflows
. See
Mark File and Select Marked
File
.
289
145
Automation Engine
145. Select Job
The Select Job workflow control is documented in the chapter
Workflows
. Find a direct link
here
.
290
Automation Engine
146
146. Select Product
The Select Product workflow control is documented in the chapter
Workflows
. Find a direct link
here
.
291
147
Automation Engine
147. Select Referenced File
This Workflow Control is documented in the chapter "Workflows". See
Select Referenced File
.
292
Automation Engine
148
148. Send E-mail
This task uses your E-mail server to send E-mails.
Your mail server must first be correctly configured in the
E-mail item in the Configure tool
.
The E-mail can contain:
• Custom text, typed in this ticket
• Any information that Automation Engine has, by using SmartNames,
• The task's input files.
1. Enter the E-mail address(es) you want the E-mail to be sent To.
When you work in a Job context that has customer information filled in, check if you can here use any of the customer E-mail addresses as a SmartName (category
Job
Information).
You can also use SmartNames to add the E-mail address of the Task Owner (category
Task
information). Learn more about SmartNames in
this chapter
.
Note:
• Multiple addresses in one field need to be separated by a semicolon " ; ".
• When you here use SmartNames, make sure they resolve to a valid E-mail address.
2. If you want, add extra E-mail address(es) in the Cc field (copy).
3. If you want, add extra E-mail address(es) in Bcc (blind copy). The recipients' E-mail address will not be displayed to the receiver.
4. Enter an E-mail Subject.
There are many SmartNames that can summarize the context of this message. An example:
Please check the attached file for job " [Job Name] ". Please mind its due date: [Job Due Date] - [Job Due Time] .
5. If you want, you can change the sender of the E-mail in From. By default the E-mail address of the Task Owner will be used.
Attention: This field requires a valid E-mail address, not just a name, alias or user name.
Note: This ability to send E-mails on behalf of the task owner (or whoever you here filled in) is subject to the configuration on your mail server. When in doubt, please consult your IT administrator.
6. Enter your Message.
Combine custom text with SmartNames to add a lot of variable information.
7. About text encoding: By default, this task uses the system's local encoding. If you notice unreadable characters when reading an Automation Engine E-mail in your E-mail program
(for example Asian characters), you best change the encoding to UTF-8.
This table shows how to enforce specific encodings:
293
148
Automation Engine
Add this to the Message field: to...
#set ($SubjectCharSet="utf-8")
#set ($ContentType="text/ plain;charset=utf-8")
set the encoding of the set the encoding of the and use plain text.
Subject to UTF-8.
Message to UTF-8
#set ($ContentType="text/ html;charset=utf-8")
set the encoding of the and use HTML.
Message to UTF-8
#set ($AttachmentsCharSet="utf-8") set the encoding of the file name of the
attachments to UTF-8.
8. If you want to include the task input files, select Attach input files.
Mind the size limits that your mail server has on attachments.
9. Select Ignore unresolved smart addressees if you want the task to continue when E-mail addresses created via SmartNames are not valid.
10.In the ticket's menu item 'Advanced', you can set public parameters if you want users to be able to fill in E-mail settings when they submit files from
Shuttle
.
Learn more in
Using Public Parameters in Workflows
.
11.Save your ticket. When you used many SmartNames, it will be valid for many situations and workflows.
Attention: Self-closing tags are not supported. For example <br/> or <address/
>. When setting up HTML E-mails, you have to use a separate opening tag and closing tag (example <address> </address>), or the empty variant (example: <br>).
294
Automation Engine
149
149. Send PostScript File to Device
This task sends a PostScript file to a PostScript device that was configured on the computer of the Automation Engine server.
Use the drop-down list to select the PostScript device you want to output to.
295
150
Automation Engine
150. Send To Nexus
This task is documented in the section on
Integrating with Nexus
. Find a direct link
here
.
296
Automation Engine
151
151. Set Priority
This Workflow Control is documented in the chapter
"Workflows"
. See
Set Priority
.
297
152
152. Sort
This Workflow Control is documented in the chapter
"Workflows"
. See
Sort
.
Automation Engine
298
Automation Engine
153
153. Split Pages
This task splits multi page PDFs into single page PDFs or PDFs with a specific range of pages.
The task also generates a RunList that contains references to all output PDFs.
• Output in: Select where you want to output the generated PDFs and the RunList.
• File Name: Enter the name of the generated RunList. By default, this is [File].jdf.
• Split Mode: Choose how you want to split the pages of the input file.
• Split Pages: This mode splits the PDF into individual single page files.
• Split In Groups: This mode splits the PDF into several files having the same number of pages. Enter this number in the field Group Size.
Note: If the task cannot output files having the same number of pages, the last output file will have less pages. For example if you ask a PDF with 10 pages to split into files of 4 pages, the task will create 2 PDFs with 4 pages and 1 PDF with only 2 pages.
• Extract Pages: This mode extracts only the pages that you specify in the field Page
Ranges. You can specify either single page numbers or page ranges with a hyphen, for example 1-3 to extract pages 1 to 3. You can add multiple numbers and ranges when you separate them by a comma, for 1-3,7,14-22.
• Output as one multi page document: Select this if you want to output all of the page ranges as one document.
• Output remaining pages: Select this if you also want to output the pages that you did not include in the field Page Ranges as one multi page PDF.
• Remaining Pages File Name: This is where you define the name of those remaining pages.
• Pages File name: Define the name of the output files here. You can use some SmartNames that are specific for this field: [Page Label] and [Page Number]. By default the
SmartName [Padded Page Number] is proposed.
Note: Padded page numbers help sorting files in alphabetical order. For example: a standard page number is 1 as in mango_1.pdf. Asking a padded page number results in mango_01.pdf. And when there are more than 99 pages, the padded page number result will be mango_001.pdf.
299
153
Automation Engine
• Copy XMP data: Enable this option to copy the XMP data of the input file into the output files.
300
Automation Engine
154
154. Split XML
This task is documented in the chapter
Integrating with External Systems
. Find a direct link
here
.
301
155
Automation Engine
155. Step & Repeat CAD based
This uses a CAD layout file as input file and places graphic files on the different designs in that
CAD layout.
This task supports MFG files (Artios Manufacturing files) and CFF2 files.
155.1 General
302
•
Output Format
• PDFPLA: In this format, the placed stations are referenced files, they are not embedded into the layout file. This keeps the layout file small but limits its use to applications that support such references: Esko editors, Esko RIPs or any next workflows steps in
Automation Engine that make use of this smart referencing.
Attention: If the input file of this task was a native PDF, this output mode will make the task end in error because a "PDFPLA can only contain references to normalized PDF".
• Normalized PDF (embed all): In this format, because all data is embedded, the PDF can be used to exchange this layout file to remote sites that also use tools that read this Esko
Normalized data. For example: off-site printers that also use an Esko RIP.
This file format is larger in Mb, however it is important to know that the technique of "PDF forms" is used: each station is only embedded once into the output file. For example if it contains 5 banana labels and 5 lemon labels, the size of the PDF will only be slightly larger than the size of 1 banana PDF plus 1 lemon PDF file.
Automation Engine
155
• PDF: This native PDF will have all data embedded and will also use "PDF forms" to optimize its size (as explained here above). Choose this output type PDF when you need to send this data to a non-Esko environment or device.
Attention: This output is only advised when the task input file is one or more native PDF(s). The advantage is then that there is no 'on the fly' normalization done on these native PDF stations ; they are untouched and are only placed into the layout native PDF.
This PDF has in its XMP also a description of the contents of its grids, their station names and amounts. Any distortion factor (here named "Shrink") will be calculated/executed in the PDF.
Note: Choosing this output type disables the options 'Screen Registration' and
' Include CAD info for Digital Flexo Suite'.
• Location Stations. Define the folder where the task can find the station files.
•
When CAD data of station and substituted file do not match, set the task status to:
• Provide info
• Generate a warning (the task will continue)
• Generate an error (the task will stop).
• Add SmartMarks by selecting a SmartMark set from the drop-down list. Or use a
SmartName to select it.
Select ' Load Mark Set in bottom layer' if you want to make sure the marks are positioned in the bottom layer, to make them appear 'behind' the graphics.
• Select ' Limit Bleed' to limit any bleed to a specific distance. The bleed mask is created by spreading the die shape.
Note: Learn more about what happens when bleed from panels overlaps in
Bleed Overlap Priority Decided by ArtiosCAD Artwork Panels
56.
155.2 Plate Setup
The sheet size is automatically extracted from the CAD template but neither
Artios MFG nor
CFF2 have a notion of 'plate'. As a result, the plate size and the position of the sheet on the plate have to be specified in the
Plate Setup tab.
303
155
Automation Engine
•
Use Sheet Size from Template: When not using the size from the template, enter own sizes (the unit is defined below).
• Fit Plate to Sheet: When the plate size needs to be different than the sheet size, deselect this option and manually enter the plate's size and its offset versus the sheet.
• Choose the matching icon for the origin of the plate.
• Define the Sheet Position on Plate by clicking or drag & dropping the red square (the sheet) to the right position on the blue square (the plate).
• If you want, enter horizontal and/or vertical Shrink values (in percentage). Learn more about when and how they are applied in
.
• Screen Registration: This is only relevant when you RIP this file on an Esko FlexRip (if you use Esko Imaging Engine, check if your version already supports this). When selected, the origin of the screening will be reset for each station on the layout. This guarantees that the exact same screening will be applied for each station. This is for example required when printing stamps. When not selected, screening will be done continuously throughout the complete layout.
Attention: This feature is ignored when you choose the output format (native) PDF.
155.3 CAD Options
304
Automation Engine
155
Both Mapping and CAD Style are options you can define in the Esko Editors.
• Mapping: When the CAD file is a CFF2 or DXF file, you here select the set of mapping rules.
These rules map line styles (cut, crease, bleed), layer names and color numbers onto
ArtiosCAD line types. These sets of mapping rules can be created in Esko PackEdge or Plato.
Learn more in the user documentation of these editors, more specifically in their section on placing files (PackEdge) or on importing CAD data (Plato).
• The CAD Style changes the appearance of the (imported) ArtiosCAD type lines. The styles you can select here were also created in PackEdge or Plato. Learn more in the their user documentation, more specifically in the section on placing ArtiosCAD files, and the option for "CAD Style".
• Include CAD info for Digital Flexo Suite:
If you are using the Esko
Digital Flexo Suite
(DFS), select this option to add the technical inks data into the header of the output file (this is usually the cut and crease lines). This data is then visible in the Esko Bitmap Viewer and also embedded in the LEN files created by an
Esko RIP.
The DFS can export this information into ACM files for an Esko Kongsberg cutting table. In
Esko PlatePatcher workflows, this information can be used to print onto the plastic sheet where the pieces of flexo plate are re-assembled. These technical lines can also represent text that is then added onto the (back of the) flexo plates, using a pen on the Kongsberg table.
Attention: This feature is ignored when you choose the output format (native) PDF.
305
156
Automation Engine
156. Step & Repeat Tabular
This task creates a step & repeat layout where the stations (one-ups) do not overlap ; their bounding boxes do not intersect.
In this ticket, data can be entered
• manually, entering numeric values.
• using SmartNames. These can be
• Formulas. For example [VPLATE]. The names of these formulas are similar to those used in Esko Plato.
• any other types of SmartNames. These can get their values from (job) parameters within
Automation Engine or they could retrieve these values from external databases, by doing
SQL queries. See an example in
. Learn more in
Database Query SmartNames
.
Note: Some ticket fields only accept SmartNames of the category 'Step and Repeat' whereas others also allow 'Global' SmartNames. Learn more in
SmartName Categories
.
Comparing this task to the 'Dynamic' version
Another tabular S&R task was created later than this one, mainly to serve workflows to digital presses. Here 's a summary comparing their unique features:
• This Step & Repeat Tabular task:
• The marks you can add need to be SmartMarks (created in PackEdge or Plato)
• Offers formulas to specify the layout
• Outputs various output formats.
Step & Repeat Tabular (Dynamic)
• The marks you can add need to be Dynamic Marks (created in the
Adobe Illustrator Plugin 'Dynamic Marks'
)
• Does not offer formulas to specify the layout
• Tailored for digital presses and/or VDP workflows
• Outputs Native PDF.
156.1 General
306
Automation Engine
156
•
Output Format
• PDFPLA: In this format, the placed stations are referenced files, they are not embedded into the layout file. This keeps the layout file small but limits its use to applications that support such references: Esko editors, Esko RIPs or any next workflows steps in
Automation Engine that make use of this smart referencing.
Attention: If the input file of this task was a native PDF, this output mode will make the task end in error because a "PDFPLA can only contain references to normalized PDF".
• Normalized PDF (embed all): In this format, because all data is embedded, the PDF can be used to exchange this layout file to remote sites that also use tools that read this Esko
Normalized data. For example: off-site printers that also use an Esko RIP.
This file format is larger in Mb, however it is important to know that the technique of "PDF forms" is used: each station is only embedded once into the output file. For example if it contains 5 banana labels and 5 lemon labels, the size of the PDF will only be slightly larger than the size of 1 banana PDF plus 1 lemon PDF file.
• PDF: This native PDF will have all data embedded and will also use "PDF forms" to optimize its size (as explained here above). Choose this output type PDF when you need to send this data to a non-Esko environment or device.
Attention: This output is only advised when the task input file is one or more native PDF(s). The advantage is then that there is no 'on the fly' normalization done on these native PDF stations ; they are untouched and are only placed into the layout native PDF.
This PDF has in its XMP also a description of the contents of its grids, their station names and amounts. Any distortion factor (here named "Shrink") will be calculated/executed in the PDF.
307
156
Automation Engine
Note: Choosing this output type disables the options 'Screen Registration' and
' Include CAD info for Digital Flexo Suite'.
• Origin: Define the point of origin from which the step & repeat is to be built.
(top left), (top right), (bottom left), (bottom right).
• Unit: Select a unit (mm or inch) to be used for all numeric fields in this task.
• SmartMarks: If you want to add marks to the step & repeat, select a SmartMarks set from the drop-down list or use a SmartName. Select ' Load Mark Set in bottom layer' if you want to make sure the marks are positioned in a newly created bottom layer, so that they appear 'behind' the graphics.
• Screen Registration: This is only relevant when you RIP this file on an Esko FlexRip (if you use Esko Imaging Engine, check if your version already supports this). When selected, the origin of the screening will be reset for each station on the layout. This guarantees that the exact same screening will be applied for each station. This is for example required when printing stamps. When not selected, screening will be done continuously throughout the complete layout.
Attention: This feature is ignored when you choose the output format (native) PDF.
• Include CAD info for Digital Flexo Suite:
If you are using the Esko
Digital Flexo Suite
(DFS), select this option to add the technical inks data into the header of the output file (this is usually the cut and crease lines). This data is then visible in the Esko Bitmap Viewer and also embedded in the LEN files created by an
Esko RIP.
The DFS can export this information into ACM files for an Esko Kongsberg cutting table. In
Esko PlatePatcher workflows, this information can be used to print onto the plastic sheet where the pieces of flexo plate are re-assembled. These technical lines can also represent text that is then added onto the (back of the) flexo plates, using a pen on the Kongsberg table.
Attention: This feature is ignored when you choose the output format (native) PDF.
•
Plate
Note: In the entry fields of this and the next tabs, click to open the SmartNames dialog.
Alternatively, right-click the field and directly choose a SmartName or formula from the offered lists.
• Size: Enter the horizontal and vertical plate size value, formula or SmartName. Learn more in
.
• Shrink: If you want, enter a shrink value, formula or SmartName. Learn more about when and how shrink is applied
•
Sheet
• Size: Enter the horizontal and vertical sheet size value, formula or SmartName. Learn more in
.
• Offset: Enter a value, formula or SmartName.
• Sheet Position on Plate: Position the sheet on plate by moving the sheet (inner) rectangle versus the plate (outer) rectangle.
308
Automation Engine
156
156.2 Grids
A tabular layout can be composed of one or multiple grids. When the layout contains two different graphics, there will be minimally two grids already. One graphic on its own can also be placed in multiple grids: for example one grid where its stations are not rotated and another grid where the stations are rotated 180 degrees.
Grid Columns
Tip: Right-click a table cell to discover several editing options.
The columns from left to right:
1. Grid number: Click the number to select the grid that you want to remove or edit.
2. File Name: The name of the one-up graphic repeated in this in this grid.
3.
Die Shape: You here define a die shape around each one-up in that grid. This will mask out any objects outside that shape. Click the field to choose between ' None' or
' Borders' (Trim Box).
Note: 'None' also means that these graphics will be excluded from the
4.
Bleed : The value you type in here spreads the Die Shape with a bleed of this distance.
The die shape is spread but die shapes will not overlap.
5.
Vertical offset to sheet : To define the top or bottom shift of the grid in relation to the sheet, depending on the setup of the
.
6.
Horizontal offset to sheet : To define the left or right shift of the grid in relation to the sheet, depending on the setup of the
.
7.
Vertical step: To define the vertical distance between two steps of the grid. The distance is calculated from the center point of the one-up to the center point of the next one-up.
8.
Horizontal step: To define the horizontal distance between two steps of the grid. The distance is calculated from the center point of the one-up to the center point of the next one-up.
9. Vertical count: To define the number of times you want to repeat the one-up vertically.
309
156
Automation Engine
10. Horizontal count: To define the number of times you want to repeat the one-up horizontally.
11. Angle: To define the angle to rotate the one-up when repeated.
12.Head Turn / Stagger: This column shows icons that illustrate the head turn or stagger that you defined for this grid (for example
Managing Grids
• Click Add Grid to add an extra grid at the bottom of the list.
Note: When this task has multiple input files, it automatically adds enough grids to have one for each input file (the ticket is automatically updated).
• To remove a grid, select it and click Remove Grid. There is no undo function.
• Select a grid and click Edit Grid to define advanced grid settings (staggering, head turns...).
on page 310.
Other Options
• Click Insert SmartNames... to choose and add SmartNames or formulas in the selected field.
•
Allow Multiple Inputs
Attention: This option is only available when you open a ticket from the
Tickets view
.
To use this option on your files, save your task ticket as a custom ticket first.
This option decides what the task should do when you launch it on multiple files.
• Select this option to generate one step & repeat file containing all of the input files. Each input file will be assigned to a different grid.
• Deselect this option to treat each input file separately. The task then generates a different step & repeat file for each input file.
156.2.1 Grid Settings
310
Automation Engine
156
• Station: These options are the same as defined in the main ticket dialog. You can choose where to define them.
• Geometry: These options are the same as defined in the main ticket dialog. You can choose where to define them.
•
HeadTurn/Stagger
• Head Turn: Choose if and how you want to rotate certain stations on this grid by 180 degrees.
•
Choose
(default).
(first button) to keep all stations as they are, without rotating them
311
156
Automation Engine
•
Choose (second button) to rotate stations in alternating rows by 180°.
•
Choose (third button) to rotate stations in alternating columns by 180°.
•
Choose (fourth button) to rotate stations both in alternating columns and in alternating rows by 180°.
312
Automation Engine
156
• Stagger: Choose if and how you want to stagger (move) certain stations on this grid horizontally or vertically.
•
Choose
(default).
(first button) to keep all stations as they are, without staggering them
•
Choose (second button) to define a vertical stagger for this grid.
•
Choose (third button) to define an horizontal stagger for this grid.
To define a horizontal or a vertical stagger:
1.
Choose or .
2. In , enter a stagger value. Choose a unit or define a percentage of the width or height of the station.
See this example of a 4 x 6 Step & Repeat with a 50% vertical stagger:
3. Restart after x Columns: You can choose to restart the staggering after a certain number of rows or columns. This means that:
• For vertical staggering: the top station of that column is positioned at the same height as the top station of the first column (it has the same vertical offset from the top of the sheet).
313
156
Automation Engine
See this example where the staggering restarts after 3 columns:
• For horizontal staggering: the first (left most) station of that row is positioned at the same horizontal offset as the first station of the first row.
• Select Continuous if you want to add extra stations to fill the blank space.
The example below is a 4 x 6 Step and Repeat (with staggering restarting after 3 columns), but the Continuous option added some stations vertically:
• Use Up & Down together with Restart after to go back in the other direction gradually instead of at once.
See this example where the staggering restarts after 3 columns, with the
Up &
Down option selected:
314
Automation Engine
156
156.3 Rules
You can modify the task's end status by setting up one or multiple smart rules.
We use an example to illustrate the options. Follow these steps to add a rule that prevents the creation of step & repeat files with more than 6 inks:
1. In the tab 'Rules', click 'Add' to open the 'Add Rule' dialog:
2. Define the 'Condition':
• What: Enter the parameter you want to check (a SmartName).
• Choose an 'expression' from the list.
• Enter the value for the parameter.
3. In Action, define what needs to happen when the Condition is met. Choose from:
• The
task finishes with a warning
• The task finishes with a warning (there's no output).
4. Click OK to confirm. The resulting rule shows up like this:
5. Add more rules if you want to. Their list will be checked from top to bottom.
Tip: You can choose to save tickets in which you switch off some rules and keep others active.
156.4 Formulas
Some of the fields work with formulas, a special set of parameters unique to this task.
315
156
Automation Engine
There are two kinds of formulas: Global formulas that define the whole step & repeat and Grid specific formulas that define individual grids.
Note: When a step & repeat contains two different graphics, there will be at least two grids.
Each grid has its own number.
Global formulas:
• VPLATEFIT: Vertical plate size that fits around a step & repeat sheet and SmartMarks.
• HPLATEFIT: Horizontal plate size that fits around a step & repeat sheet and SmartMarks.
• VPLATE: Vertical plate size.
• HPLATE: Horizontal plate size.
• VSHEETOFFSET: Vertical offset of the sheet relative to the Plate.
• HSHEETOFFSET: Horizontal offset of the sheet relative to the Plate.
• VSHEETFIT: Vertical sheet size that fits around the step & repeat.
• HSHEETFIT: Horizontal sheet size that fits around the step & repeat.
• VSHEET: Vertical sheet size.
• HSHEET: Horizontal sheet size.
• SHEETTOP: Top position of the sheet relative to the Plate.
• SHEETLEFT: Left position of the sheet relative to the Plate.
• SHEETBOTTOM: Bottom position of the sheet relative to the Plate.
• SHEETRIGHT: Right position of the sheet relative to the Plate.
• NROFINKS: Number of non-technical inks (Technical inks will not be printed).
• NROFGRIDS: Number of grids.
Grid specific formulas (x = the grid number):
• VLABELx: Vertical size of non-rotated station.
•
HLABELx: Horizontal size of non-rotated station.
• VSTEPx: Vertical step size, from center point to center point.
• HSTEPx: Horizontal step size, from center point to center point.
• VSIZEx: Vertical size of bounding box of rotated station.
• HSIZEx: Horizontal size of bounding box of rotated station.
• VCOUNTx: Number of vertical step & repeats in grid x.
• HCOUNTx: Number of horizontal step & repeats in grid x.
• ANGLE: Angle of the rotation.
• GRIDVSIZEx: Vertical size of the grid (top-bottom).
• GRIDHSIZEx: Horizontal size of the grid (left-right).
• TOPx: Top position of the grid relative to the sheet.
316
• LEFTx: Left position of the grid relative to the sheet.
• BOTTOMx: Bottom position of the grid relative to the sheet.
• RIGHTx: Right position of the grid relative to the sheet.
• BLEEDx: Distance to spread the grid die shape with.
Example of a Grid defining an Automatic Fill
1. First we need to define a absolute size for sheet/plate:
Automation Engine
156
2. Now you can enter these grid settings:
Clarification of the formulas:
a. First you define the vertical (and horizontal ) count of the grid: the vertical count is the vertical size of the sheet divided by vertical size of the station: VSHEET / VLABEL1. For the horizontal count, use HSHEET / HLABEL1 .
b. Then you are able to define the vertical (and horizontal ) step: vertical step is the vertical sheet size divided by the vertical count: VSHEET / VCOUNT1. For the horizontal step, use HSHEET / HCOUNT1 .
c. Now for the vertical (and horizontal ) offset: you want to center the step & repeat on the sheet. You can do that by defining the vertical offset as half the vertical step minus the vertical size of the station: (VSTEP1-VLABEL1)/2. For the horizontal offset, use (HSTEP1-HLABEL1)/2 .
317
156
Automation Engine
156.5 Using Database Queries: an Example
Many fields in this task can be defined by SmartNames. And SmartNames can get their values by doing SQL queries to non-Esko databases. This means that your tabular Step & Repeat ticket can automatically get (some of) its values directly from this external source ; no need for an
Esko user to type them in again.
We use this simple example of a database describing your dies:
First we need to create these SmartNames, then we add them into the task ticket.
1. See this (old) example of how an SQL query SmartName is created to retrieve the value for vertical gap.
Attention: This page only summarizes how to do this. Learn more details in the chapter '
SmartNames
', specifically in '
Database Query SmartNames
'.
318
In this example, we created these SmartNames:
Automation Engine
156
• DB_DrumH: Retrieves the value for the horizontal size of the drum.
• DB_DrumV: Retrieves the value for the vertical size of the drum.
• DB_GapH: Retrieves the value of the gap's horizontal size.
• DB_GapV: Retrieves the value of the gap's vertical size.
• DB_Teeth: Retrieves the number of cylinder teeth.
• DB_StepH: Retrieves the value of the die's horizontal step.
• DB_StepV: Retrieves the value of the die's vertical step.
2. Now use those SmartNames in a ticket of the Step & Repeat Tabular task. Use the Insert
SmartNames... button, or right-click, browse and select it.
The General tab can look like this:
319
156
320
The Grids tab can look like this:
Automation Engine
Automation Engine
157
157. Step & Repeat Tabular (Dynamic)
This dynamic version of the Step & Repeat Tabular task allows you full interactive control over the positioning of files, much like if you would do this in
PowerLayout
(an Esko plug-in for Adobe
Illustrator).
Attention: The Marks you add to this layout need to be 'Dynamic' marks. You can not add SmartMarks here (marks created in PackEdge or Plato).
Use this task when you do not use a template that was created with PowerLayout. If you do
want to use such a template, then use the task
Step & Repeat Template based (Dynamic)
on page
334.
The task outputs a native PDF file.
Caution: Make sure you define a specific name for the output file, this to avoid overwriting the (first) input file.
Task Options
Selecting one of the items in this list displays their available settings on the right. Almost all of these are identical to those in 'PowerLayout' (learn more in the
documentation of PowerLayout
.
As usual, many of these options can be set by using SmartNames.
• Job: Click these links to learn more about your options for the complete layout:
•
•
•
•
•
• Grid selection: Use
to Add or Remove grids.
Note: Grids are numbered sequentially. When there are 3 grids and you remove 'Grid 2', then ' Grid 3' will automatically be renamed to 'Grid 2'.
• Preview: The preview shows the position of all grids. The selected grid is highlighted in orange. Any others are displayed in blue.
157.1 Assignment of Input Files
How this task assigns the incoming files to a grid depends on the type of input:
• A single PDF file with only a single page: This triggers an automatic Grid Filling, i.e. every cell of the grid will be filled with the one-up input file.
• A single PDF file with multiple pages: The task creates only one grid with each page placed once, in a single cell, not repeated.
321
157
Automation Engine
Tip: Use an XML input file to also repeat these pages. For example: a PDF has 3 pages, each page contains a design variant / flavor of the design. The XML can then specify that it needs
1.000 bananas (page 1), 500 apples (page 2), etc. Learn more below
• Multiple PDF files: By default, the ticket automatically creates a grid for each PDF: the 1st input file will be placed in the first grid, etc.
Tip: Use the '
Sort
' workflow control to change this sequence of input files before entering this task.
Attention: There is an exception that is valid in a dynamic VDP workflow (where each input file only needs to be output once): When the input files follow the naming convention <SameFileName-Number>, they will be grouped together in a same grid.
For example, banana-001.pdf, banana-002.pdf , banana-003.pdf will be placed in a same grid.
•
An XML file for each grid. Learn more in the dedicated page
Specification of RunList XML in
on page 328.
157.2 Splitting Output, Blocks and Gaps
To limit the size of the output PDF file, this task also uses the technique of "PDF forms": Each input PDF file is only embedded once into the output file.
When used in a VDP context, where each station can contain a different graphic, this size can become huge and easily reach the computer’s processing power limit. Tasks handling such files require a lot of system memory and read/write operations, and this impacts the processing speed. Some RIPs also have problems processing huge PDFs.
This is why you can choose to split this output. The task then creates a set of smaller PDFs instead of a single large one.
Choose how you want to split the output file:
• No (Single File).
• Automatically. The task then calculates the number of sheets per file so that the output file sizes stay within reasonable limits.
• On Number of Sheets. This way, each output file except the first and last one contains the
Number of Sheets (pages) specified.
• On Block Size of Grid 1 (only valid for output to digital presses):
Note: Learn about the concept of Blocks and Gaps
.
A block with an optional gap must fit completely on sheets. This can be expressed by a formula: (block_rows + gap_rows) mod grid_rows = 0. The task will fail when this is not the case for the first grid.
Note: In formulas, 'mod' stands for the 'modulo' operation: the remainder (leftover) after division. For example "9 mod 3" results in 0, but "5 mod 2" results in 1. Learn more about
'mod' on
this wiki page
.
Use this mode when there is only one grid or if that condition is met for all grids. This feature assumes that if the user took care to enter specific values for rows and gaps, that he then likely will want to use those same numbers for splitting.
322
Automation Engine
157
When defining this choice via SmartNames, the resulting value must match one of these: OFF,
AUTO, SHEETS, BLOCK.
Blocks and Gaps: Concept and Examples
Note: Some example use cases:
• You need to print 10.000 labels and deliver them on reels of 500 labels. You then define a block of 500 a add a gap between those blocks (empty one-ups).
• You want those gaps to cover the complete circumference of the reel, to cover the labels underneath and so protect them from any damage. In case of VDP each label might even be unique.
Blocks are used to split jobs into fixed length segments and to control the filling order. They are defined per grid. Each grid can have different block settings:
• Block Length is a number of rows.
• Gap Length is a number of rows ("zero" = no gap).
• Grid Height is the number of rows in a grid.
A gap works as a separator. It is represented by one or more empty rows inserted between two blocks.
• If block length + gap length = grid height, then a gap will appear on each sheet on the same place.
• If block length + gap length mod grid height > 0, then the gap will be floating ; it will appear on different positions.
• If block length + gap length > grid height and block length + gap length mod grid height = 0, then a gap will appear on the same position on the sheet but not on each sheet.
Here are 3 examples of the above mentioned 3 cases:
323
157
Automation Engine
157.3 Sheet and Plate Options
The Sheet Size is the area where your one-up grids will be positioned within the Plate.
You can define:
• Plate Size: Define its horizontal and vertical size.
Note: The plate size will correspond to the Media Box of the generated step and repeat
PDF.
Caution: Take the printer's size limits into account when defining these values.
• Shrink: Shrink is used to compensate for plate distortion, later in the output process. Learn more about when and how shrink is applied
324
Automation Engine
157
• Sheet Size: This is the printable area on your plate.
Note: The sheet size will correspond to the Trim Box of the generated step and repeat PDF.
• Position on Plate: The blue square in the image represents the position of the sheet on the plate. You can click or drag this blue square to match the desired alignment.
• Offset: Use this to fine-tune the position. The values are calculated versus the light gray lines.
157.4 Filling Order
Note: We here refer to the one-up print items as 'items'.
These Filling Order options define how the items should be distributed over the grid. You can specify:
• a starting point
• whether the grid should be filled by row or by column
• gaps (empty stations on the grid).
Options:
• Scope Settings:
• Same Settings for all Grids: This applies all the settings in this tab to each grid in the layout. This automatically disables setting a filling order on grid level.
• Individual Settings for Each Grid: Select this to set the (different) filling order on grid level.
• Start Content Filling: Choose where the first print item is printed (the next options then decide how the other items will follow):
•
: Top left. When using a SmartName, its value should be TL .
•
: Top right. When using a SmartName, its value should be TR .
•
: Bottom left. When using a SmartName, its value should be BL .
•
: Bottom right. When using a SmartName, its value should be BR .
• Also specify whether the grid is to be filled 'by row' or 'by column' .
See the preview of your selected options on the right hand side.
• The
Printing direction marked with an arrow indicates the direction that the paper/ substrate flows through the press.
325
157
• In that preview, a black dot shows the first record.
• Some examples:
• The distribution starts on top left, with vertical flow:
Automation Engine
• The distribution starts top right, with vertical flow:
• The distribution starts top left, with horizontal flow:
• Fill over: Choose if you want to distribute the items over the Complete Job or over Blocks.
Learn about the concept of blocks
.
• If you choose Blocks, the flow of variable data (the one-up variants) will run over blocks of a specified size, then run over the next block when the previous one is complete.
The preview also shows the blocks:
326
Automation Engine
157
Block Size: You can define their size as the complete 'Job' or an amount of Sheets or
Rows.
• When, in ' Fill over', you selected 'Complete Job', then the Block Size will be 1 Job by default.
You can set it to another unit if you still want to print in blocks, but without having the flow of (variable data) items respect the block. This is useful if you want to add gaps (see below).
• Gap between Blocks: This option is available if you have chosen to Fill over Blocks, or to fill over the Complete Job but still have blocks (as explained above).
This option adds white space in between the blocks.
Gap Size: Define the size of this gap.
157.5 Adding Marks
Use this tab to add Dynamic Marks to your layout.
Learn more about Dynamic Marks in the description of the task "
on page
12".
157.6 Setting specific Grid Options
• Specify the Cell Width and Cell Height for the one-up item ("cell").
• Set the grid Orientation and Clip Bleed.
327
157
Automation Engine
defines the initial Orientation of the one-ups in this grid. Their orientation within the layout can be changed further by the option Head Turn.
' Clip Bleed' creates a clipping mask around the one-up, to clip any bleed to the desired distance.
Note: Deselecting 'Clip Bleed' can cause one-ups to overlap. This can be useful in some special layouts.
Note: Learn more about what happens when bleed from panels overlaps in
Bleed Overlap Priority Decided by ArtiosCAD Artwork Panels
56.
Note: Learn more about bleed
in the manual of PowerLayout Standalone
.
•
Repeat
Define how many times you want to repeat the one-up (V & H) and define the gap between these repeats (V & H).
• If wanted, specify a Head Turn and /or Stagger.
Learn more about these options
.
• Specify the Position of this grid using the positioning tool and Offset distances.
Define the positioning reference for this grid: Attach to the Sheet or the Plate area.
In below example, the top center of the (bounding box of the) layout will be placed on the left bottom corner of the (bounding box of the) reference (that you defined in 'Attach to').
In ' Offset', you can still move the layout based on the above defined position. The direction of the offset (up, down, left or right) depends on the positioning, and is indicated by the arrows.
157.7 Specification of RunList XML in Dynamic Step &
Repeat
Dynamic Step & Repeat tasks can use XML files to specify their input files (one-ups) and how they should be placed on the layout. Such files typically come from external systems where production planning was decided. This page describes the format that such a "RunList" XML file needs to have.
Structure
The XML file may contain only an XML header and a single root element RunList. UTF-8 coding is needed to support non-ASCII characters in file paths.
328
Automation Engine
157
Note: While XML-files support UTF-8 encoding, all file names must follow the URL-encoding.
This means that all characters other than basic ASCII letters and numbers (A-Z, a-z, 0-9) and a few punctuation marks ('-', '_', '.' and '~'), must be percent-encoded (for example a space is noted as "%20"). Learn more about percent encoding in
http://en.wikipedia.org/wiki/Percentencoding)
.
<RunList>
The RunList element can be used only at the root level and the current file format supports only one RunList element per file.
This element is used as a container that holds together one or more nodes of
RunListItem
(which describe one-ups for a specific grid).
It also contains an attribute Version, specifying the version of the RunList format. At this moment only version 1.0 is supported.
Attention: Each grid in the Step & Repeat must have an own RunList item and because only one is allowed per file, this means that each grid must have its own XML file.
<RunListItem>
This element is used to contain a reference to the one-up file. It contains following mandatory elements:
Table: RunListItem for Step & Repeat Dynamic tasks
Element Format Description
FileName URL
File specification of one-up file. It must be a valid URL (absolute path).
Note: Special characters must be properly coded (see common XML rules).
FirstPage integer Index of the first physical page from the used page range. The first page in
PDF has index 1.
LastPage integer Index of the last physical page. Also this index starts from 1.
Example: Page range 1..1 means single page with index 1. Page range 1..2 means pages 1 and 2.
Repeats
integer Number of page range repetitions (value must be greater than 0).
Note: Page range 1..3 is repeated in this way: 1, 2, 3, 1, 2, 3, 1, 2, 3,...
Under these conditions a reserved value -1 is allowed:
• Only one RunListItem in RunList
• FirstPage must be same as LastPage.
In this case the task will calculate the number of repeats automatically to fill the complete grid.
Note: Note: This feature is intended for 'static' jobs (not Variable Data jobs).
Example
329
157
Automation Engine
This example shows a RunList with two one-ups to be used in a grid:
• The first one-up is presented by a range of three pages (1-3) from the file A.pdf and needs to be repeated two times.
• The second one-up is presented by a single page (1) from file B.pdf and needs to be repeated five times.
The final order of pages used as one-ups will be: A1, A2, A3, A1, A2, A3, B1, B1, B1, B1, B1
<?xml version="1.0" encoding="UTF-8" ?>
<RunList version="1.0">
<RunListItem>
<FileName>file://server/JobContainer/Item1/A.pdf</FileName>
<FirstPage>1</FirstPage>
<LastPage>3</LastPage>
<Repeats>2</Repeats>
</RunListItem>
<RunListItem>
<FileName>file://server/JobContainer/Item1/B.pdf</FileName>
<FirstPage>1</FirstPage>
<LastPage>1</LastPage>
<Repeats>5</Repeats>
</RunListItem>
</RunList>
Grid Filling with an XML RunList
If the task input file consists of a single XML file,
• with only one <RunListItem>,
• where both the <FirstPage> and the <LastPage> are the same,
• and where the number of repeats is set to "-1", then a special behavior is triggered, called Grid Filling. This means that every cell of the grid will be filled with the specified static one-up.
330
Automation Engine
158
158. Step & Repeat Template based
Concept
This task creates a step & repeat file based on an template layout that was made earlier. This mode makes it useful for all packaging print segments: labels, boxes, flexibles, etc. It is typically used to make an identical layout but now for variant graphics with a same size as those placed in the template.
Note: About the name of the output Step & Repeat file:
• When no name is specified, the output file name will be the name of the first task input file.
SmartNames based on this output file name will also follow that rule.
• When you choose the Output Format "PDF" and not "PDFPLA" (learn more below), the system will avoid that you ever overwrite your input file PDF name ; it will, in the output file name, automatically attach a suffix *_rep* to the name of your first input file.
• When you type in a specific output file name yourself, it will be honored, even when it then overwrites a file.
Tab 'General'
•
Output Format
• PDFPLA: In this format, the placed stations are referenced files, they are not embedded into the layout file. This keeps the layout file small but limits its use to applications that support such references: Esko editors, Esko RIPs or any next workflows steps in
Automation Engine that make use of this smart referencing.
Attention: If the input file of this task was a native PDF, this output mode will make the task end in error because a "PDFPLA can only contain references to normalized PDF".
• Normalized PDF (embed all): In this format, because all data is embedded, the PDF can be used to exchange this layout file to remote sites that also use tools that read this Esko
Normalized data. For example: off-site printers that also use an Esko RIP.
This file format is larger in Mb, however it is important to know that the technique of "PDF forms" is used: each station is only embedded once into the output file. For example if it contains 5 banana labels and 5 lemon labels, the size of the PDF will only be slightly larger than the size of 1 banana PDF plus 1 lemon PDF file.
• PDF: This native PDF will have all data embedded and will also use "PDF forms" to optimize its size (as explained here above). Choose this output type PDF when you need to send this data to a non-Esko environment or device.
Attention: This output is only advised when the task input file is one or more native PDF(s). The advantage is then that there is no 'on the fly' normalization done on these native PDF stations ; they are untouched and are only placed into the layout native PDF.
331
158
Automation Engine
This PDF has in its XMP also a description of the contents of its grids, their station names and amounts. Any distortion factor (here named "Shrink") will be calculated/executed in the PDF.
Note: Choosing this output type disables the options 'Screen Registration' and
' Include CAD info for Digital Flexo Suite'.
• Template: This can be:
• A PDFPLA file (any earlier made step & repeat file)
• A normalized PDF file that contains external references (representing the stations)
• A JDF file that contains "packaging stripping" info.
Note: When you define a template by using a SmartName, the below column "In
template" will only mention "All Stations in Template". This disables the possibility in this ticket to set custom station replacements. In case your workflow needs that, then consider using the
• Stations: This is where you decide which files will replace the template stations in the output file.
Before you can define the new station in this ticket, you first need to select an input file before opening the ticket. Then select the template (click the browse button and select it).
• The ticket reads the template and presents its stations (referenced files) in the column
In
template. The task input files are listed in the column Replace by.
332
Changing or defining the "Replace by" stations: Click on any name of a file in the column ' Replace by' and you will see a list with these options:
• <do not substitute>: Select this to not replace it. See the below described option
Delete station(s) ... to decide what happens then.
• To replace it with the first task input file
Automation Engine
158
• To replace it with the second task input file
• Etc.
• Select.... After selecting a station in the Replace by column, this button allows you to browse to another file (that was not already an input file for this ticket). Alternatively, use
SmartNames.
• When the borders of a station file and substituted file do not fit, you can define how this affects the task status:
• Provide info. The task will end in status 'OK'. The task details and log file will mention which stations did not have the same borders.
• Generate a warning. Same info is given but the task ends in status 'Warning'.
• Generate an error. Same info is given but the task ends in status 'Error'. There is no output file.
• Delete station(s) in template file which have not been substituted.
• When this option is selected, the not-replaced stations will, in the output file, be empty
("delete").
• When this option is not selected, the not-replaced stations will, in the output file, be those from the template ("keep").
• You can add SmartMarks.
Attention: If you use a template that contains macros from the old Esko application
QuickStep, these macros will be lost. You need to replace these macros with
SmartMarks.
Tab 'Plate Setup'
The options are identical as described in
of the Step & Repeat CAD based task.
Tab 'CAD Options'
The options are identical as described in
of the Step & Repeat CAD based task.
333
159
Automation Engine
159. Step & Repeat Template based
(Dynamic)
Concept
Use this task to place one-ups (print items) into grids based on a PDF template.
In this task, the template containing the grids needs to be created in PowerLayout, an Esko plug-in for Adobe Illustrator. Learn more in the
manual of PowerLayout standalone
.
Selecting the template
In Task Options, in the item 'Job', select the desired Template that describes the grid(s).
When a template is selected, all other information in this task is automatically filled in with information from the template. You will be unable to change any of the information in the task.
Learn more about these options in
this page about the S&R Tabular (Dynamic) task
.
Attention: Filling Order is not applied globally. Therefore, when you specify the filling order for each grid separately, ensure that the number of grids in this ticket matches the number of grids in the template file.
Input Files
The order of the input files is especially important when you work with templates.
Tip: Use the '
Sort
' workflow control to change this sequence of input files before entering this task.
Learn more in
this page valid for both S&R Dynamic tasks
.
Split Output options
Learn more in
this page about the S&R Tabular (Dynamic) task
.
334
Automation Engine
160
160. Submit to CDI
This task is documented in the chapter
CDI Platemaking Workflow
. Find a direct link
here
.
335
161
Automation Engine
161. Submit to Gang Run
This task is documented in the chapter
Gang Run Printing for Sign & Display
. Find a direct link
here
.
336
Automation Engine
162
162. Submit to Kongsberg Table
This task is documented in the chapter
Kongsberg Production Workflow
. Find a direct link
here
.
337
163
Automation Engine
163. Submit to Plate Merger
This task is documented in the chapter
CDI Platemaking Workflow
. Find a direct link
here
.
338
Automation Engine
164
164. Submit XML to Gang Run
This task is documented in the chapter
Gang Run Printing for Sign & Display
. Find a direct link
here
.
339
165
Automation Engine
165. Synchronize ArtiosCAD Boards
This task synchronizes the boards in the ArtiosCAD database with those in the database of an external system.
This task is set up by an Esko Solution Architect.
For more information, search for online articles on this topic in the
Esko Knowledge Base
.
340
Automation Engine
166
166. Synchronize ArtiosCAD Companies
This task synchronizes the companies in the ArtiosCAD database with those in the database of an external system.
This task is set up by an Esko Solution Architect.
For more information, search for online articles on this topic in the
Esko Knowledge Base
.
341
167
Automation Engine
167. Track Edit Session
Automation Engine can track and log interactive editing actions in Esko editors. Define
in the
Configure tool
for which editors you want this automatic tracking.
When you open a file that resides in an active Job (folder) in an Esko editor, this task will automatically start logging many important editing actions. The task automatically stops when
someone closes the file in the editor.
This editing information can so also automatically
• be stored in the Task History.
• be made available by using Notifications, for example as an XML file to report to another system. You could also save all notifications locally in the Job folder or centrally and you can
do this in one or several files. Learn more
.
Note: This task cannot be launched interactively. It will start appearing when you
configured it
.
Keep in mind that the editor needs to be restarted to activate this setting.
Note: When editing files in ArtPro, the task only records the timings of opening and closing the file.
167.1 Viewing the Edit Session Information in the Pilot
In the Pilot, the task's Details already show what is logged. An example:
342
Automation Engine
167
Note: Notice in above screenshot how, when at the end the operator saved the file as *_BCK, that the tracking task closed and immediately started a new one, now for the file with that other name.
167.2 Storing the Editing Information System-Wide
How can these edit logs be stored automatically?
• Make sure the task is automatically archived into the tool
Task History
.
• Alternatively, use the
Notification tool
to create a rule specific for this task:
• Either you save all these XML logs inside the Job folder. The SmartNames you use in the output location allow you to choose if you want one (XML/TXT) log for each file or one per day or etc.
• Alternatively, you save all these XML logs per customer or even system-wide. In that case you just indicate an output path somewhere outside the Job folder.
Follow these steps to create such a rule:
1. Go to Configure > Notification > Rules
2. In the Tasks tab, select the task Track Edit Session.
3. Click Add. The Notification Rule Editor opens.
4. To get an XML, select the Action 'Create XML File in folder' .
5. Define the folder's Location and click OK.
343
167
Automation Engine
167.3 Which Edit Actions are Logged?
These types of edits are logged:
• Which user opens which file from which workstation?
• Start and stop time of this editing session
• Was the file saved or closed? When and with what name?
• All loading, saving, placing, exporting functions
• All changes to inks, layers, pages, page sizes
• All changes to (Esko) barcodes
• HIFI color conversions
• All trapping actions, PSFix actions, InkWizard actions
• Creating and replacing of external references
• Die object edits: adding, turning, flipping, rotating
• Writing of task notifications (when closing the edit session)
• Any loss of connection with the server.
An example:
*** Start interactive PackEdge 7.0 ***
Time 13/01/06 17:19
User wde@aeserver01
Automation Engine server AESERVER01
Loading file file://aeserver01/52355/
Prod/52355_YummieBeer_back.pdf
Remove layer OMBRE
Trap with local ticket Default
"Modified ink angle for C from 22 to 7 degrees"
"Created ink PANTONE 123 C (100 lpi, 7 degrees, dot ?, type
Normal)"
"Created ink C (170 lpi, 75 degrees, dot ?, type Normal)"
"Created ink ROUGE (170 lpi, 45 degrees, dot ?, type Normal)"
Placing file file://aeserver01/52355/
Prod/52355_YummieBeer_collar.pdf
Changed page margins to top 3.998, bottom 9.998, left 4.001,
right 66.001 mm
344
Automation Engine
167
Changed page size to width 110.0024 mm and height 73.99 mm
PS-Fix: modified 2 contour(s)
Applied Job inkmapping
"Modified ink angle for C from 7 to 75 degrees"
"Removed ink M (170 lpi, 15 degrees, dot ?, type Normal)"
Changed page margins to top 7.25, bottom 7.25, left 7.25, right
8.36 mm
Exporting file file://aeserver01/52355/
Prod/52355_YummieBeer_back.tif
Saving file file://aeserver01/52355/
Prod/52355_YummieBeer_back2.pdf
*** End interactive PackEdge 7.0 ***
Time 13/01/07 17:22
Notification:Wrote XML file:E:\wdedata\52355\Prod\Edits
\52355_YummieBeer_back.
345
168
Automation Engine
168. Trap with PowerTrapper
Learn about the concept of trapping in
This task uses the Esko technology "PowerTrapper". Its input file needs to be a native or normalized PDF.
The resulting trapping objects are created in a dedicated (new) layer.
The output of this task is a Normalized PDF file.
The task's many settings are spread over these tabs:
•
•
on page 349
•
•
on page 352
•
168.1 What is Trapping?
The trapping process is a safeguard against possible fluctuations in the printing process.
Minor discrepancies in registration and slight paper shifting can cause inks to misregister.
When two adjoining colored objects do not touch exactly, the printed result can show a white gap, as well as areas with a dark overlap:
'Trapping' these objects causes the objects to slightly overlap each other:
346
In general, trapping is necessary when two adjoining color areas don’t share a common ink.
Automation Engine
168
Adding a fine area where they join, made of a color that contains components of both adjoining colors, can effectively 'trap' such areas.
168.2 Distance & Direction
1. Trapping: Choose between two modes:
• Normal Trapping: This selects adjoining color pairs, which are likely to cause registration problems like ugly light gaps, and unwanted halo effects. Lighter colors are generally trapped into darker colors to minimize the visual effect of the trap.
• Reverse Trapping: This mode avoids overprinting of inks. It prevents overprint of adjoining color areas by trapping these color pairs with a white knockout (erasing) trap.
The white knockout trap is put on top of the lighter of the two colors. This is useful to prepare a file for "Dry Offset" printing (example: printing on metal cans).
2. Trapping Distance: Enter the width of the traps. The default width is 0.2 mm (or its equivalent in
your chosen unit
).
Below, you can define specific distances when trapping Into black, Into spot color, Into
image or adding a Pull Back (see below).
3. Minimum Ink Difference
Trapping is applied to two adjoining colors, when either:
• The two colors each consist of at least one ink but they have no common inks.
• The two colors have common inks but there is a difference of at least the
Minimum Ink
Difference percentage for two or more inks making up these colors.
These differences in ink percentages must be in opposite directions.
347
168
Automation Engine
Note: An example: With the default minimum ink difference percentage of 10%, the following two colors are trapped:
• 1st color: C 5%, M 10%, Y 50%, K 15%
• 2nd color: C 5%, M 10%, Y 85%, K 5%
• => These colors have 2 inks that differ 10% or more: K is 10% different, Y is 35% different.
Increase the Minimum Ink Difference to trap colors that differ more ; lower it to trap colors that are similar.
4. Image Trapping
• Automatic: This determines the most suitable trap direction automatically. It compares the average lightness of the image with the lightness of the adjoining area, and then traps the lighter color into the darker one.
• Always Towards Image: This always traps line art under adjoining images.
• Always Towards Line Art: This always traps images under adjoining line art.
Select ' Trap images to images' if you want images to be trapped with each other.
5. Pull Back
When a color area is composed of multiple inks bordering to a very light background, you can ' pull back' ink to keep away all ink except the darkest ink. This prevents individual inks from that composed color to become visible in the background, typically due to registration errors during printing.
• Automatic: This creates pull backs on rich black or rich spot colors, when the color left in the pull back area is not very different from the composed color.
• Only Pull Back Rich Black: This only creates pull backs on rich black.
• Do Not Pull Back: This never creates any pull back.
There will be automatic pull back for the darkest color. Select ' Also pull back light inks' to create pull backs even when the pull back ink (i.e. the ink remaining in the pull back area) is visibly different from the composed color. Select ' Pull back images and gradients' to create pull backs on images and gradients.
6. Trap Decision
• Use Lightness: This uses the color luminance to define the trapping direction, except for opaque inks, where it uses the inks order.
• Trap direction: from brightest to darkest.
• Treat Spot Colors as Opaque: Color luminance is used only for CMYK. For opaque and spot inks, the trap direction is determined by the ink sequence.
• Trap direction for spot colors only: towards the separation that is listed the lowest in list of inks.
• Trap direction goes from the process to the spot color if the spot color is below the process color in the list of inks.
• Trap direction if the spot color is above the process color: from brightest to darkest.
348
Automation Engine
168
• Use Separation Order: The trapping direction is determined by the ink sequence for all inks, including CMYK.
• Trap direction: towards the separation listed the lowest in the list of inks.
• Use Reverse Separation Order: As above, but using the reverse ink sequence.
• Trap direction: towards the separation listed the highest in the list of inks.
7. Overshoot Mode: See some visual examples in the
PackEdge user manual
( Menu > Trapper
> PowerTrapper ).
• Automatic: The centerline behavior is according the rules determined in the color pair list.
• Never on Dark Areas: The centerline is forced not to get beyond the center of dark areas.
• Never: The centerline is forced not to get beyond the center of any area.
168.3 Color & Shape
• Trap Color Intensity: By default, the task uses the full color of the object to spread in the trap area (100% trap color intensity). You can create a trap of a lighter color by reducing this percentage.
• Image Trap Color: Choose how to trap your images:
•
Use Original Image Data: When the image is clipped, the task uses the underlying image data to create the trap. When there is no underlying image data (when the image is not clipped), an empty trap is created.
•
Extend Image Data: The task automatically extrapolates the image along its four edges to ensure that the trap looks as expected, even if there is no clipped image data outside the visible image.
•
Use an Approximate Flat Color: Instead of using existing or extrapolated image data in the trap, the task uses a solid color. A suitable color is determined by averaging the image's colors along its boundary with the object to trap.
•
Truncate Traps: Truncating the trap object avoids that it sticks out on another color.
Choose a mode:
349
168
Automation Engine
• On Center: When a portion of a trap comes too close to the contour of another object, it is limited to half the distance between the trapped object and the other object.
• On Edge: When a portion of a trap comes too close to the contour of another object, it is truncated on the other object's edge.
• End Caps: Choose the shape of the ends of an open trap:
• Square: The trap ends at a right angle to the adjoining object.
• Round: This rounds the ends of the trap. This is typically only used in combination with white knockout (' Reverse Trapping').
Note: We recommend that you do not to use 'Round End Caps' together with 'Truncate
Traps On Center', as this can generate some artefacts (the round caps are truncated).
• Object Dependent: The trap is a logical continuation of the contour of the spread object.
• Trap Corners: Choose how sharp corners should be handled:
350
• Round: Corners end in a round cap.
• Beveled: Sharp corners are cut off.
• Mitered: If the distance from the base of the trap to the corner point is larger than the Miter Ratio multiplied by the trap distance, then the corner will be beveled, otherwise it will remain sharp.
The default miter ratio is 4. This means that if the length of the sharp corner is more than 4 times the Trapping Distance, the corner is cut off (beveled). If it is less than 4 times the Trapping Distance, the corner is left as it is.
• Truncate Traps: If you want to truncate traps into black differently, select Into black and choose the truncation mode ( On Center or On Edge).
Automation Engine
168
168.4 Processing
• Color Pairs:
Before creating trap objects, PowerTrapper scans the file for color pairs where this will be needed. A color pair can occur only once or it can occur many times. The task can trap all hits (occurrences) of a color pair in the same way or it can recalculate the trap direction for different hits.
• Each hit can have its own decision: This recalculates the trap direction for each hit of a color pair.
• Use the same decision for all hits: This traps all hits of the same color pair in the same direction.
• Use the same decision for objects smaller than: This uses the same trap direction for hits of a color pair belonging to small objects, and recalculates the trap direction for hits belonging to bigger objects.
Use the input field next to determine the maximum size of small objects.
• Objects:
To speed up the trapping, the task can safely ignore certain object types.
•
Only selected objects
•
Respect existing traps: If the file has already been trapped, select this option to keep the existing trap layer out of the trapping process.
• Ignore bitmaps: Select this to keep bitmap pixel data from being trapped. Bitmap data is contourized before trapping which may slow down trapping. Bitmaps with lots of small isolated islands typically take a longer time to trap.
Note: When you indicate an object type to ignore, it is ignored completely as if it did not exist in the file. Also, the ignored objects do not truncate trapping areas resulting from other objects below them.
• Small Gaps:
Some files contain very small unintentional gaps between neighboring objects. These gaps prevent trapping of these objects. Although it is better to clean up such files before trapping, PowerTrapper can ignore these gaps automatically.
351
168
Automation Engine
To use this option, select Close when smaller than and enter the maximum size small gaps can have.
Note: If you set a big gap size, trapping may become slower and some small parts may be ignored.
168.5 Rules
This tab allows to add rules that define custom trapping settings for specific trapping pairs.
PowerTrapper first traps the trapping pairs that match such a rule (according to that rule) and then traps the rest of the file according to the main trapping settings.
When to use Rules?
In most cases the general trapping settings entered in ' Distance &Direction' give you excellent results. You can refine them using rules.
Settings defined in rules overrule settings in the other tabs.
Note: This is an advanced feature. We recommend it for experienced users.
Some example cases to custom rules:
• To set a different trap distance for a specific spot ink. Sometimes you need a larger trap distance for spot inks if there is no other ink to help cover leaks on the press.
• To prevent trapping or ink pull back in specific cases. Depending on the type of the adjoining colors, trapping and/or pull back may be undesirable.
• To force a specific trap direction. When adjoining colors have a similar lightness level,
PowerTrapper selects an arbitrary direction. You can use a rule to make it always use a particular direction for a color pair.
• To specify a different shape and/or truncation mode for certain color pairs. For example, you can choose to use ' On Center' truncation when trapping under a 100% black line and
' On Edge' truncation on all other color pairs.
Creating a rule
1. Click Add.
2. In the dialog, use the 'From' and 'To' lists to specify trapping pair that you want to apply this rule to. Choose between '
Any Color, a particular ink (Process, Spot or Opaque), a particular object (
Image, Gradient or Empty Background) or the Registration Color.
Note: When trapping a particular ink, you can also define its 'Minimum Density' and if the
Color must be pure (no other separation in the color object).
3. Choose the contents of the rule.
Most options are described in the previous pages. Here are some specific settings within these rules:
• Direction Mode: Select 'Into Both Colors' to use bidirectional trapping. In that case, the trap goes half the trapping distance in each direction.
352
Automation Engine
168
• Horizontal/Vertical Distortion: Set the percentage of the trapping distance to be used in V/H direction.
See an example where the trap was generated with no vertical distortion (so 100%, i.e.
using the entered trap distance) and horizontal distortion set to 50% (i.e. half the trap
distance).
You can use the + or - buttons to add or remove criteria to your rule.
4. Click Add to confirm and add the rule.
5. After defining the rules, click OK to confirm this list of rules.
168.6 Output
• Trap layer only: Select this to output a PDF containing only the trap layer.
• Load trap color pairs if present: Select this to make the task use a TCP file that was created during a previous trapping action. The TCP file needs to have the same name as the input file and needs to be present next to the input file.
353
169
169. Unzip
You can use this task to extract files from a zipped archive.
Automation Engine
Note: Many applications can create zip files, also the
in Automation Engine.
• Define what needs to happen If the files already exist at the destination location:
• Fail. The task will not unzip and will end in an error status.
• Overwrite the files and give a warning.
• Overwrite the files.
• Character Set:
When a zip file was generated with non-standard encoding, unzipping such a file with this
Unzip task can fail. The task's log file then mentions a ‘MALFORMED’ exception. You can solve this by specifying the character set that was used to create the file.
For the list of character sets and the correct naming to be used in this task ticket, we refer to
this page of the online java documentation
. When specifying a character set in this ticket, use the name as is listed on that page, in the column “Canonical Name for java.nio API”.
354
Automation Engine
170
170. Upload via FTP
This task is documented in the chapter
Integrating with External Systems
. Find a direct link
here
.
355
171
Automation Engine
171. Upload via SFTP
This task is documented in the chapter
Integrating with External Systems
. Find a direct link
here
.
356
Automation Engine
172
172. Upload To Cloud Storage
This task is documented in the chapter
Integrating with External Systems
. Find a direct link
here
.
357
173
Automation Engine
173. Verify Certification
This task is documented in the chapter
Quality Control tools
. Find a direct link
here
.
358
Automation Engine
174
174. Version PDF
When working with various versions of a single PDF, such as multiple language versions or versions containing minor differences, you can use this task to save on output material by:
• Combining a base file with multiple version files.
• Extracting separations or layers from the base file and replacing them by variants.
Combine Base with Version Files
By combining a base file (the input file) with a number of version files, you can create various flavours of the same file and save on output material.
For example: Your base file contains graphics and only the CMY separations. Your version files contain text in different languages in the black (K) separation. By combining the graphics in your base file with the various language versions, you only need to make the plates containing the separations for the graphics once.
Follow these steps:
1. In the Version Files table, click Add.
2. In the External File dialog, specify:
• The location of the Version Folder, which contains the version files.
• The name(s) of the Version File(s), including their file extension.
• The name of the Output File, which is a combination of the base file and a version file.
3. Choose what you want to do with the Version Input File (base file or input file):
• If you want it to remain in the same place, choose Leave.
• If you want it to be deleted, choose Delete.
359
174
Automation Engine
• If you want it to be moved to another folder, choose Move to and use the button to define the new location.
4. Select the desired Reference Page Box. Selecting the correct media box here can prevent errors, such as double time stamps in the text of a page mark.
5. Determine the Order of the Base File and the Version file.
6. Separation Isolation: Select 'Isolated' to use the PDF construct "Form Isolation" to combine the files, which will reduce the interaction between the content of the files. This is helpful when the files contain information for different separations, rather than artwork to be placed on top.
Note: You can use SmartNames and wild cards to specify folders or files.
Note: You cannot combine Normalized PDF files with other PDF files.
Extract Separations from Input file
This Action allows to extract a separation from the input file and map it to another separation.
This is done to limit the total number of separations for output.
360
For example: Map a 'black' Pantone color that is used for text to 'K' (typically black in CMYK).
Extract Layers from Input file
This Action allows to extract layers from the input file and split the input file into a fixed master and a variant part. The variable ink is often black.
Automation Engine
174
You can also work with layers to extract the language layer from the input file and replace it with the corresponding translation(s).
Note: Work with wild cards to optimize your workflow: For example to only extract the language layer, use 'lang_*' if you know that all language versions follow this name rule. This will allow for the lang_EN, lang_FR and lang_ES layers to be automatically extracted from the base file.
361
175
Automation Engine
175. Wait
This task is documented in the chapter
Workflows
, in the section
Inserting Wait Points
.
362
Automation Engine
176
176. Wait for Action (Checkpoint)
This task is documented in the chapter
Workflows
, in the section
Building Workflows → Inserting
Wait Points
.
Find a direct link
here
.
363
177
Automation Engine
177. Wait for Files
This task is documented in the chapter
Workflows
, in the section
Inserting Wait Points
.
364
Automation Engine
178
178. Wait for Files (via JDF)
Use this task when you are working with a JDF RunList, and when the files referenced in the
RunList are not ready yet.
Send the JDF RunList to this task, and it will check at a regular interval if the files are already present. When it finds all the files, it ends in OK and passes them on to the next workflow task.
Example Workflow
1. The MIS system creates jobs via JDF, and sends the JDF RunList to your Automation Engine workflow.
2. The Wait for Files (via JDF) task checks if all the files referenced in the RunList are where they are supposed to be.
3. When the files are ready, the task finds them and passes them on to the next workflow task.
4. The rest of the workflow starts on the files.
Parameters
•
Look in Folder
By default, the tasks looks for the files at the location defined in the RunList. However, you can here define a custom location where the task should look for them.
Tip: For example, use the SmartName [URL of Folder of Input] if you know the files will be end up in the same folder as the RunList.
•
Stop waiting when time exceeds ...
Select this if you want the task to finish if the files referenced in the RunList haven't been found after a specified time.
If you don't select this parameter, the task will wait indefinitely (or until it finds the files).
•
Task ends in error when not all files were found
Select this if you want the task to finish with an Error state:
• When the time you set in the ' Stop waiting when time exceeds' parameter has passed,
• and when the task hasn't found the files referenced in the RunList at that specified time.
365
179
Automation Engine
179. Wait for Product Status
This task allows to hold a workflow until one or more Products have reached a certain status.
This task is documented in the chapter on
Products
. Find a direct link
here
.
366
180. Zip
This task creates a zip file from the selected input file(s) or folder.
Choose the task's behavior in case the zip file already exists:
•
Generate an error
• Replace the zip file.
Learn more in
Automation Engine
180
367
181
Automation Engine
181. Outdated and Soon Outdated Tasks
181.1 Concept of (Soon) Outdated Tasks
Concept
Some task technology in Automation Engine can become outdated after many years. There are two possible reasons for this:
• the functionality is now available via a new and improved technology. For example a task based on a new trapping engine replaces the old ones.
• the functionality is no longer used in today's prepress environment. For example a task to normalize EPF files, an Esko file format that is not created any more.
Such tasks are first declared “ Soon Outdated” and later become “Outdated”.
Note: Before version 14.1, the term Deprecated was used for Soon Outdated tasks and the term Obsolete was used for Outdated tasks.
Soon Outdated
A task is named Soon Outdated as a warning that it will no longer be available in the next major version of the Automation Engine.
This gives you at least one year
• to replace this task by an alternative. This could be a newer task equivalent or a slightly different workflow. The alternative is mentioned in this documentation.
• to contact Esko support in case the proposed alternative is not valid for you.
Outdated
A Soon Outdated task becomes Outdated in the next major version: it is then no longer available in that software version.
• Customers who never used that task type will not see any tickets.
• Customers who had already created custom tickets of that task type will still see those tickets but notice that they no longer work.
A Gradual Process with Many Visual Reminders
This two step process gives you the time to switch from using the old technology to the new version or method.
The Pilot shows you in many places which task types are (to be Soon) Outdated.
• In the Tickets list:
368
Automation Engine
181
Also workflow tickets that contain outdated tasks will show a warning:
• In the task ticket itself, a colored top bar is added. A Soon Outdated task shows an orange bar and the link for
More Info brings you to the online help page that describes the
proposed alternative:
An Outdated task shows a red color bar and also a link with More Info:
• In the
Workflow Editor. Colored text indicates (soon) outdated workflow steps:
Transitions that depend on an outdated step are shown in grey. That part of the workflow
also does not work any more:
These (soon) outdated steps are also mentioned in the Validate Workflow dialog. When you there select such a warning, the corresponding step will also be highlighted in the workflow editor with an arrow.
369
181
Automation Engine
181.2 Expand Variable Data to PPML File (Soon
Outdated)
The Expand Variable Data to PPML File task will soon be outdated. Learn more about
outdated and soon outdated tasks in
Concept of (Soon) Outdated Tasks
on page 368.
This task was used in VDP workflows and used an older technology (the PPML file format).
Find a link below to its old documentation.
Alternative
Digital printing is a fast-evolving field, and the industry as whole is moving towards the PDF/VT file standard as a replacement for the older PPML standard. Esko is supporting this trend.
Esko recommends you to migrate to the Dynamic VDP workflow.
The Dynamic VDP workflow is based on PDF/VT and includes a DeskPack plug-in for authoring as well as an Automation Engine ticket for expansion.
181.2.1 Expand Variable Data to PPML File (Soon Outdated) - old documentation page
Note: Learn about the alternative for this task in the above page
The old documentation can still be found in older manuals of Automation Engine. To find it, go to
•
http://help.esko.com/products/Automation%20Engine
• then, in "Version", select a version older than version 14
• click on the link to the
Reference Guide
• go to The Tasks: an Overview > Deprecated and Obsolete Tasks > Expand Variable
Data to PPML File (Deprecated) .
181.3 Expand Variable Data to PPML File (DeskPack
Only) (Soon Outdated)
The Expand Variable Data to PPML File (DeskPack Only) task will soon be outdated. Learn
more about outdated and soon outdated tasks in
Concept of (Soon) Outdated Tasks
on page
368.
This task was used in VDP workflows started from Adobe Illustrator and used an older technology (the PPML file format).
This task was documented in the page describing the non-DeskPack version: Find a link in
Expand Variable Data to PPML File (Soon Outdated) - old documentation page
on page 370.
370
Automation Engine
181
Alternative
As mentioned in
Expand Variable Data to PPML File (Soon Outdated)
, the alternative here is also to use the Dynamic workflow tools. This Dynamic workflow is based on PDF/VT and includes a
DeskPack plug-in for authoring as well as an Automation Engine ticket for expansion.
181.3.1 Expand Variable Data to PPML File (DeskPack only) (Soon
Outdated) - old documentation page
This task is the version of
Expand variable Data to PPML file
that can be started from DeskPack.
181.4 Preflight via External Application (Soon Outdated)
In Automation Engine 16, this task was declared "soon outdated".
Learn more about (soon) outdated tasks in
Concept of (Soon) Outdated Tasks
on page 368.
Alternative
To preflight, please use the
Preflight with PitStop task
.
When you use another preflight product than PitStop you can use the
.
181.4.1 Preflight via External Application (Soon Outdated) - old documentation page
As mentioned in
, this task will soon be outdated.
Its documentation can still be found in older manuals of Automation Engine. Follow these steps to find it:
• Go to
http://www.esko.com/en/Support/Product?id=Automation%20Engine
.
• In "Version", select the version 14.1.
• Click on the link to the Complete Manual.
• Go to Reference Guide > The Tasks and Workflow Controls > Preflight via External
Application .
181.5 Print on Digital Press (PPML) (Soon Outdated)
This task will soon be outdated. Learn more about outdated and soon outdated tasks in
Concept of (Soon) Outdated Tasks
The Print on Digital Press (PPML) task was used to create variable print jobs on the DFE server using the format PPML.
Find a link below to its old documentation.
371
181
Automation Engine
Alternative
Digital printing is a fast-evolving field, and the industry as whole is moving towards the PDF/VT file standard as a replacement for the older PPML standard. Esko is supporting this trend.
Esko recommends you to migrate to the Dynamic VDP workflow.
The Dynamic VDP workflow is based on PDF/VT and includes a DeskPack plug-in for authoring as well as an Automation Engine ticket for expansion.
181.5.1 Print on Digital Press (PPML) (Soon Outdated) - old documentation page
Note: Learn about the alternative for this task in the above page
The old documentation can still be found in older manuals of Automation Engine. To find it, go to
•
http://help.esko.com/products/Automation%20Engine
• then, in "Version", select a version older than version 14
• click on the link to the
Reference Guide
• go to The Tasks: an Overview > Print on Digital Press (PPML) .
181.6 Process Remote Proofs (Soon Outdated)
In Automation Engine v16, this task was labeled 'Soon Outdated'.
Learn more about (soon) outdated tasks in
Concept of (Soon) Outdated Tasks
on page 368.
Alternative
For remote proofing, we recommend to create a self-contained PDF of the job and send it to the remote site. Automation Engine offers many methods of transfer (network copy, E-mail attachment,
Access Points
, ...).
Also, Automation Engine can transfer the file to Esko WebCenter which was designed to manage online approval cycles.
Also, Esko Pack Proof can be installed at the remote site(s) and configured with any necessary color information such as ink books and color strategies. Adding to that, an Automation Engine workflow can be configured at the remote site to automatically output the proof file when it arrives.
181.6.1 Process Remote Proofs (Soon Outdated) - old documentation page
As mentioned in
, this task will soon be outdated.
372
Automation Engine
181
Its documentation can still be found in the 14.1 manual of Automation Engine. Follow these steps to find it:
• Go to
http://www.esko.com/en/Support/Product?id=Automation%20Engine
.
• In "Version", select the version 14.1.
• Click on the link to the Complete Manual.
• Go to Reference Guide > The Tasks and Workflow Controls > Process Remote Proofs .
181.7 Rip to WS4000 Series (Soon Outdated)
The Rip to WS4000 Series task will soon be outdated. Learn more about outdated and soon
Concept of (Soon) Outdated Tasks
on page 368.
This task was a used to generate JLYT output for a HP Indigo WS4000 press.
Find a link below to its old documentation.
Alternative
Your alternative is to use the more recent
on page 226 task. This task links to the DFE that you configured in
Digital Press
.
181.7.1 Rip to WS4000 Series (Soon Outdated) - old documentation page
Note: Learn about the alternative for this task in the above page
The old documentation can still be found in older manuals of Automation Engine. To find it, go to
•
http://help.esko.com/products/Automation%20Engine
• then, in "Version", select a version older than version 14
• click on the link to the
Reference Guide
• In the search field, type WS4000. The result will show a link to the task's old documentation.
181.8 Send to Odystar (soon outdated)
Because all Odystar functionality is by now available within Automation Engine, the
will soon be outdated.
Learn more about (soon) outdated tasks in
Concept of (Soon) Outdated Tasks
on page 368.
Alternative
373
181
Automation Engine
Please use the functionality within Automation Engine.
181.8.1 Send to Odystar (soon outdated) - old documentation page
As mentioned
, this task will soon be outdated.
Its documentation can still be found in older manuals of Automation Engine. Follow these steps to find it:
• Go to
http://www.esko.com/en/Support/Product?id=Automation%20Engine
.
• In "Version", select the version 14.1.
• Click on the link to the Complete Manual.
• Go to User Guide > Integrating with other Esko applications > Integrating with
Odystar .
181.9 Tasks that became outdated in this version
In this version of Automation Engine, these tasks were removed because they became
Outdated (they were earlier announced as "Soon Outdated"):
• Add Parameters for Nesting
• Adjust PDF Screening
• Create Nested Layouts
• Export to GRS File
• Export to VRML File
• Fork
• Make Plate on CDI
• Image to MJM File (JDF)
• Trap - Prepare Trap Pairs
• Trap - Create Trap Layer
• Trap - Prepare and Create Trap Layer
Note: Find their documentation in earlier versions of the Automation Engine manual.
Note: Learn more about how and when tasks become outdated in
374
Atsisiųsti
Vieša nuoroda atnaujinta
Vieša nuoroda į jūsų pokalbį buvo atnaujinta. You may view and manage your chat links after registration here.
Dokumento vieša nuoroda
Reklama
