Psion Teklogix 7035, 8255, 8260 Terminals Manual

Twin Client Reference
For the 7035, 8255, and 8260 Terminals Manufactured by Psion Teklogix
Copyright © 1996 - 2005 by Connect, Inc.
All rights reserved. This document may not be reproduced in full or in part, in any form,
without prior written permission of Connect Inc., 1701 Quincy Avenue, Suites 5 & 6,
Naperville, IL 60540.
Connect, Inc. makes no representation or warranties with respect to the contents
of this document and specifically disclaims any implied warranties of
merchantability or fitness for any particular purpose. Further, Connect, Inc.
reserves the right to revise this publication and to make changes to it from time to
time without obligation to notify any person or organization of such revision or
changes.
Trademarks
PowerNet OpenAir™, OpenAir Linux™, OpenAir Windows™, OpenAir 400™,
PowerNet Twin Client™, and PowerNet AirLinc™, are trademarks of Connect,
Inc.
Other product names mentioned in this manual may be trademarks or registered
trademarks of their respective companies and are hereby acknowledged.
Production
This manual was written, edited, and produced by:
Connect, Inc.
1701 Quincy Avenue,
Suites 5 & 6
Naperville, IL 60540
www.connectrf.com
Printed in the U.S.A.
Please let us know about any errors in this document at:
http://207.241.78.223/isoxpert/calltrak.nsf/WebTracking?OpenForm
Table of Contents
Chapter 1 • Introduction............................................................................................. 1-1
In This Manual…………….. ..........................................................................................1-1
Connect, Inc. Product Line Overview.........................................................................1-1
Twin Client Overview……. ...........................................................................................1-2
Chapter 2 • Installation............................................................................................... 2-1
Installation Requirements. ..........................................................................................2-1
Downloading From the WEB .......................................................................................2-1
Running Setup from a Download File ........................................................................2-1
Installation Wizard……….............................................................................................2-2
Running the Manager……. ..........................................................................................2-4
Chapter 3 • Quick Start .............................................................................................. 3-1
Configuring the Manager.............................................................................................3-1
Downloading Files To the Terminal............................................................................3-8
Booting the Terminal……. ...........................................................................................3-8
Starting a Telnet Session.. ..........................................................................................3-9
Chapter 4 • Standard Setup ....................................................................................... 4-1
Setup Using Twin Client Manager ..............................................................................4-1
Terminal Setup Using Twin Client Menus..................................................................4-7
Authorizing Twin Client…. ........................................................................................4-10
Chapter 5 • Advanced Setup ..................................................................................... 5-1
Selecting the Advanced Setup....................................................................................5-1
Customizing the Keyboard..........................................................................................5-2
Customizing the Display… ..........................................................................................5-4
Customizing the Scanner. ...........................................................................................5-7
External Scanner Setup…. ..........................................................................................5-9
Setting Log Levels……….. ........................................................................................5-10
Customizing Timers……… ........................................................................................5-10
Customizing Alarms………........................................................................................5-12
Customizing Printers……. .........................................................................................5-14
Miscellaneous Customizations .................................................................................5-17
Twin Client Reference • June, 2005
iii
Chapter 6 • Advanced Integration ............................................................................. 6-1
Keyboard/Mapping………. ...........................................................................................6-1
Keyboard Macros…………...........................................................................................6-4
Scanner/Data Mapping….. ...........................................................................................6-6
Scanner/Data Editing……. ...........................................................................................6-8
Scan/Decoder Control…… ..........................................................................................6-9
Display/Mapping………….. ........................................................................................6-11
Display/Formatting………. .........................................................................................6-13
Printer/Init…………………. .........................................................................................6-13
Dialog………………………. .........................................................................................6-14
Extended Commands……. ........................................................................................6-19
Advanced Display Options for VT/HP ......................................................................6-23
Advanced 3270 Keyboard Options ...........................................................................6-24
New Environ Telnet Extension..................................................................................6-26
Chapter 7 • The Display Formatter............................................................................ 7-1
Setting the Emulation…… ...........................................................................................7-1
Starting the Emulator……. ..........................................................................................7-2
Taking Snapshots………… ..........................................................................................7-4
Formatting…………………. ..........................................................................................7-5
Chapter 8 • Software Management ........................................................................... 8-1
Airloader Auto-Configuration......................................................................................8-1
Mobile Device Manager (MDM) Features…………. ....................................................8-7
Manual Download of Configuration Files.................................................................8-17
Chapter 9 • Keypad Configuration ............................................................................ 9-1
7035 36-Key Diagrams…… ..........................................................................................9-1
7035 36-Key Table…………..........................................................................................9-5
7035 44-Key Diagrams…… ..........................................................................................9-8
7035 44-Key Table…………........................................................................................9-12
7035 56-Key Diagrams…… ........................................................................................9-15
7035 56-Key Table…………........................................................................................9-19
8255/8260 QWERTY Diagrams ..................................................................................9-22
8255/8260 QWERTY Table .........................................................................................9-26
8260 ABC Diagrams……… ........................................................................................9-29
8260 ABC Table…………… ........................................................................................9-33
iv
Twin Client Reference •
June, 2005
8260 AZERTY Diagrams….........................................................................................9-36
8260 AZERTY Table……….........................................................................................9-40
Chapter 10 • Error Message Resolution Guide ...................................................... 10-1
Twin Client Reference • June, 2005
v
This page is intentionally blank.
vi
Twin Client Reference •
June, 2005
Chapter 1 • Introduction
In This Manual
This manual is organized as follows:
• Chapter one provides an introduction to the Twin Client.
• Chapter two describes how to load the Twin Client Manager software on a Windows
95, 98, ME, XP, NT/2000, or 2003 PC.
• Chapter three describes how to quickly configure the Twin Client Manager and the
terminal for automatic, over-the-air software download and subsequent Telnet
session startup.
• Chapter four describes how to change the Standard setup options.
• Chapter five describes how to use the Advanced setup options. These options are
used to customize keyboard, display, scanner, timer, alarm, and printer operation.
• Chapter six describes how to use the Twin Client advanced integration tools to
further customize terminal operation. The creation and use of mapping, macro,
dialog, and scanner control objects are described.
• Chapter seven describes the use of the built-in Twin Client Formatter, and how to
configure the portable terminal to use screen formatting.
• Chapter eight describes how to use the Airloader Auto-Configuration tool to manage
and automatically maintain the software configuration of all terminals on the wireless
network. Also described are software management procedures and options that are
unique to Psion Teklogix terminals.
• Chapter nine contains keypad configuration information for the 7035 and 82xx
terminals.
• Chapter ten is a reference for terminal error messages in Twin Client.
Connect, Inc. Product Line Overview
Connect, Inc.’s products bridge the gap between portable wireless devices and network
applications, making the entire wireless enterprise as productive, efficient, and reliable as
possible. The Connect, Inc. family of products supports the following:
• All Internet-compatible wireless networks, encompassing virtually all wireless LAN
technologies on the market today. Spectrum One, a proprietary spread spectrum
wireless technology in the 900Mhz band, is also supported.
• All Internet-compatible wire network media, including Ethernet and Token Ring.
• All major user interfaces.
• All possible network application architectures including direct client, client-server,
and three-tier client server.
Twin Client Reference
• June, 2005
1-1
Introduction
Twin Client Overview
Twin Client is a software package that includes an easy-to-use Windows program for
configuring and downloading the software to the portable terminals.
Mode of Operation
Twin Client operates in Telnet client mode.
Telnet client mode provides a telnet connection directly to host computers and their
applications.
In Telnet mode, all application protocol processing is performed on the terminal.
Major Features
Twin Client for Psion Teklogix terminals offers the following benefits:
• Simplicity: Twin Client is preset to match the default keyboard overlays and
functionality of the Psion Teklogix Telnet client. No special configuration procedures
are required.
• Management: Administrators and integrators can monitor and modify the software
revision and configuration of each portable terminal from any Windows PC attached
to the TCP/IP network. Changes are downloaded to the terminals over the wireless
LAN automatically.
• Formatting: The Twin Client Terminal Screen Formatter feature is built-in, allowing
integrators to tailor host application displays to suit the needs of the terminal
operators without modifying the applications. The Display Formatter is only
available for the ANSI emulation.
• Internationalization: Error message language translations and character sets are
menu selections. No additional integration is necessary.
• Migration: Conversion to a client-server environment is automatic because the
Server client is included in the Twin Client software already downloaded to the
terminal.
1-2
Twin Client Reference
• June, 2005
Chapter 2 • Installation
This chapter describes the installation of the Twin Client software on a Windows 95, 98,
ME, XP, NT/2000, or 2003 PC. The software can be downloaded from the Connect web
site. Instructions are provided below.
Installation Requirements
Installation of Twin Client requires, at a minimum, the following:
• A Pentium-class processor
• 32 MB of RAM
• 10 MB of free hard disk space available
• Microsoft Windows 95, 98, ME, XP, NT/2000, or 2003 operating system
Downloading From the WEB
1. Go to http://www.connectrf.com on the Partner Services page.
2. Click on the Software Download icon.
3. Select the applicable Twin Client Manager software.
4. Click on the Version number to download software.
5. Click on Setup.exe and follow Installation Shield wizard.
6. Follow the steps in the Authorizing Twin Client section of Chapter Four.
Running Setup from a Download File
The downloaded file is a compressed archive. After extraction using a utility such as
WinZip or PKWARE, folders are created on the hard disk as shown in the following
figure.
Click on the Disk1 folder to view the files as shown in the following figure.
Twin Client Reference
• June, 2005
2-1
Installation
Click on the Setup application and proceed to the following section entitled Installation
Wizard for further instructions.
Installation Wizard
The InstallShield wizard runs and presents the following screen.
Click on Next to begin the installation process.
2-2
Twin Client Reference
• June, 2005
Installation Wizard
To change the default Destination Location, click on Browse and select a location. Then
click on Next.
The default folder is Twin Client. This default may be changed either by selecting an
existing program group or by typing in a new name at the prompt. Then click on Next.
The Twin Client Manager and terminal files are then installed in the target folder.
Twin Client Reference • June, 2005
2-3
Installation
When the installation is complete, reboot the system to initialize the Twin Client
software.
a. To reboot the system immediately, click on Finish.
b. To reboot later, click on the option to restart the computer later, and then click on
Finish.
Running the Manager
The Twin Client Manager is the utility that manages the terminal software and
configurations. Select Twin Client Manager from under Start, Programs, etc.
Note: If the PowerNet splash screen flashes for a second and ends when the Twin Client
Manager is run, move the file at this link
(http://www.connectrf.com/Documents/fix-flash.reg) to the system with the
problem and then run it. This issue, found in earlier versions of the Twin Client
Manager, has been fixed in later versions by using a later MS compiler and
libraries.
The Twin Client Manager screen appears as shown in the following figure. This is the
administrator's main screen, and all functions are accessed from its menu bar, toolbar,
and tabs.
2-4
Twin Client Reference
• June, 2005
Running the Manager
Menu Bar
The menu bar provides access to the functions used to configure the terminals and
manage their software. Subsequent chapters of this manual explain each menu and its
options.
Toolbar
Under the menu bar, the toolbar provides shortcuts to major features. The toolbar can be
turned on or off by changing the Toolbar parameter found on the View menu. The
shortcuts available from the toolbar are as follows:
Create a new terminal configuration.
Open an existing terminal configuration.
Save the current terminal configuration.
Download the configuration to the terminal.
Download software to the terminal.
Configure terminals automatically over the wireless network.
View the Twin Client Manager version.
The Twin Client Manager is now successfully installed and ready for use. The next
chapter provides detailed instructions for quickly configuring the terminal and starting a
telnet session.
Twin Client Reference • June, 2005
2-5
Installation
This page is intentionally blank.
2-6
Twin Client Reference
• June, 2005
Chapter 3 • Quick Start
This chapter describes how to prepare the Twin Client Manager and the Psion Teklogix
terminal for a Telnet session with the host. Following an initial serial download, the
terminal software and configuration are managed automatically, over the wireless
network.
Note: Psion Teklogix terminals are normally delivered with Psion Teklogix files pre-
installed. However, if the terminal does not have those files installed refer to
Chapter 8, Manual Download of Configuration Files, before proceeding.
Configuring the Manager
The first step is to configure the Twin Client Manager to meet site-specific requirements,
and then prepare it for the automatic management of the terminal software and IP
addresses. This simple procedure will require only a few minutes to complete.
Setting the Emulation
Click on Twin Client Manager from under Start, Programs, etc., and then select the
Settings menu as shown below.
Click on Emulation, select the desired emulation, and then click OK.
Twin Client Reference
• June, 2005
3-1
Quick Start
Setting the Servers
The Servers are the Telnet host systems the terminals will access.
To set these addresses from the Settings menu, click on Servers and then click on Add.
Enter the name of each server, its IP address and IP port (normally 23 for Telnet servers),
and emulation type. Then click on OK.
Repeat this step for each telnet server the terminals are required to access. If an error is
made in the name, IP address, IP port number, or terminal emulation type, click on the
line that is in error and then click on the Edit button to make the corrections. Use the
Load button if you want to load an .svr file. Use the Save As button if you want to save
your file as an .svr file.
Setting Terminal Operations
Select Terminal Operation from under Settings in Twin Client Manager.
The option of Run Airloader on terminal can be selected, and the Airloader server
IP address can be entered in this screen.
3-2
Twin Client Reference
• June, 2005
Quick Start
The Teklogix scanner supports long-range scanning. To activate the long-range scanner,
enter the value in seconds for Timeout for laser aiming beam (secs). Teklogix supports
a minimum of 1 second and a maximum of 3 seconds for laser aim time.
Note: The terminal will reboot when dot time values are changed.
Click OK after entering information.
Setting Terminal Model and COM Port
The default terminal model is 7035, and the default serial connection to the Psion
Teklogix terminal is through COM1. To select a specific Psion Teklogix terminal model,
or to change the COM port assignment, click on the Options menu as shown.
Choose 7035 or the terminal model of your choice.
Twin Client Reference • June, 2005
3-3
Quick Start
Saving the Configuration
Click File and Save As. Enter a name for this configuration.
For the purposes of this example, the name is vt220.
3-4
Twin Client Reference
• June, 2005
Quick Start
Setting Airloader Auto-Configuration
The configuration download and IP address assignment for each terminal will take place
automatically by setting the Airloader Auto-Configuration options.
Click on the Airloader option in the Tools menu.
Note: If the Airloader Auto-Configuration window does not display the options, click
on the Advanced>> button.
If multiple network adapters are installed on the PC, ensure that the desired network
adapter is selected. Click the Change button to select the appropriate adapter.
This powerful software management tool is described in detail in the Chapter 8 section,
AirLoader Auto-Configuration. For now, it is sufficient simply to use it for assignment of
the initial terminal configuration and IP address, both of which can be easily changed
later. Ensure that all of the check boxes are checked as shown above.
Click on the Addresses button to assign user specific IP address range.
Twin Client Reference • June, 2005
3-5
Quick Start
After setting the address range, click on OK to return to the Airloader Auto-Configuration
screen and then click on the box next to the terminal group manager.
The display expands to include the default terminal Group. Next, click on the New
Group icon and use the Browse button to select the configuration file saved earlier.
3-6
Twin Client Reference
• June, 2005
Quick Start
Check the Active box, and the system is now configured to automatically download IP
addresses, software, and configuration files to the terminals. Click on the box at upper
right corner to return to the main menu.
Note: The software does not need to be authorized now. It can be authorized later, after
a Telnet session has been established. The procedure is described in the Chapter
4 section entitled Authorizing Twin Client.
Twin Client Reference • June, 2005
3-7
Quick Start
Downloading Files To the Terminal
Twin Client program and configuration files are installed on the terminal with the
following procedure. Boot the terminal, according to the directions in the next section.
At the DOS prompt, run ld.bat from the a:\ drive, but do not Enter at this time.
Under the Terminal menu, click on the Send Program Files to Terminal menu option.
At the prompt, choose Yes or No to download configurations. Choosing Yes is needed to
run in telnet mode.
The following screen will appear.
Now, choose Enter on the terminal, while choosing OK at the prompt above.
The files will transfer at this time. Watch the terminal to see that the correct files are
loading. Boot the terminal according to the following section. The Twin Client Manager
will then automatically manage the terminal software and configuration.
Booting the Terminal
At any time it is necessary to update the terminal software and/or configuration, the
terminal must be booted by pressing and holding down the <Blue> key and the
<Enter/On> key for 7 seconds.
A successful wireless connection is indicated by the display of the Twin Client main
menu shown below.
3-8
Twin Client Reference
• June, 2005
Quick Start
Twin Client
© 1991-2005, Connect, Inc.
Press Any Key
Note: The date of 2005 is updated on the terminal at the time of a new release.
The terminal is now ready to establish a Telnet session with the host system.
Starting a Telnet Session
At the Twin Client main menu on the terminal, press any key to establish the connection.
Until the terminal has been authorized, the following screen is displayed.
RECOVERABLE ERROR
Terminal not
Authorized for
Twin Client
Press Any Key …
It is not necessary to authorize the terminal at this time, so press any key to continue. The
terminal will establish a connection with the host system and start emulation. If the
terminal fails to connect to the host, refer to the following tables for the possible causes
and the related corrective actions.
Failure Cause
Corrective Action
Incorrect Host IP
address
Incorrect netmask
value
Correct the Host List address on the terminal. Refer to Terminal
Setup Using Twin Client Menus for instructions.
Access the Edit Functions menu. Correct the netmask value. Refer
to Terminal Setup Using Twin Client Menus for instructions.
Error Indication
Possible Cause
Corrective Action
NOT Associated
Invalid NETID or
ESSID
Unable to open
connection
Timeout waiting
for data
IP stack on terminal
failed to load.
Transient
communications
failure
Socket closed during
download
Run current radio setup program and set
NETID or ESSID to match the access
point. See Terminal Setup Using Twin
Client Menus for instructions.
Reload Program Files and reboot.
Download
aborted
Reboot terminal. If problem persists,
check the RFSYNC.log in the
TwinClientTN directory.
Ensure that PC is operating. Reboot
terminal and retry.
After a Telnet session has been successfully established, the terminal will remain in
session for a maximum of 30 minutes at a time until it has been authorized. Once
authorized, there is no software restriction on the session time. The instructions for
authorizing the terminal are presented in Authorizing Twin Client.
Twin Client Reference • June, 2005
3-9
Quick Start
This page is intentionally blank.
3-10
Twin Client Reference
• June, 2005
Chapter 4 • Standard Setup
The default terminal setup is sufficient for most installations. However, to meet sitespecific requirements, it may be necessary to customize terminal operation. The standard
setup options simplify this process and can be modified by the following methods:
• Using the Twin Client Manager.
• Using the Twin Client terminal menu system.
This chapter describes how to use the Twin Client Manager and the terminal menu
systems to set up the terminal. Also described are the methods for authorizing the
terminal software.
Setup Using Twin Client Manager
The Twin Client Manager provides a Standard Settings tab for automatic setup of the
terminals. The options within this tab vary according to the emulation selected, each of
which is described below.
VT and HP Settings
Select the VT and HP emulation setup by clicking on the Settings menu and then the
Emulation menu, as shown below.
Then click on the VT100, VT220, or HP700 selection, as shown below.
Twin Client Reference
• June, 2005
4-1
Standard Setup
Click on OK after the selection is made, and return to the main Twin Client Manager
menu. The standard settings tab will now reflect the settings for VT/HP emulation.
Quadrant Mode
This scrolling list option defines the rules by which the terminal display is positioned in
the larger host display. As defined by Twin Client, quadrants are fixed position
"windows" in the host display, and the terminal display is located on whatever quadrant
contains the current cursor position.
Off disables quadrant processing and Twin Client simply centers the current host
input field in the terminal display.
On enables quadrant processing. However, input fields that cross quadrant
boundaries result in a shift to the left in order to locate as much of the current input
field on the terminal display.
Soft always positions on a quadrant boundary regardless of input field boundaries.
Viewing keys are enabled.
Hard is the same as Soft except the viewing keys are disabled.
Lock locks the terminal display origin (upper left corner) to fixed row and column
(x,y) coordinates in the host display. The coordinates are zero-based.
4-2
Twin Client Reference
• June, 2005
Setup Using Twin Client Manager
Font Size
These check boxes enable (checked) or disable (unchecked) the display of characters in
double high and double wide font.
Key Click
This option is used to automatically transmit a keystroke to the vt100 host when the
vt100 field matches the selected attribute. The automatic keystroke generation can be
based on whether the input is scanned, or keyed, or both.
Printer Type
This scrolling list selects the attached printer type. The default value is none, indicating
no printer is attached.
5250 Settings
Select the 5250 emulation setup by clicking on the Settings menu and then the
Emulation menu, as shown below.
Then click on the 5250 selection, as shown below.
Click on OK after the selection is made, and return to the main Twin Client Manager
menu. The standard settings tab will now reflect the settings for 5250 emulation.
Twin Client Reference • June, 2005
4-3
Standard Setup
Quadrant Mode
This scrolling list option defines the rules by which the terminal display is positioned in
the larger host display. As defined by Twin Client, quadrants are fixed position
"windows" in the host display, and the terminal display is located on whatever quadrant
contains the current cursor position.
Off disables quadrant processing and Twin Client simply centers the current host
input field in the terminal display.
On enables quadrant processing. However, input fields that cross quadrant
boundaries result in a shift to the left in order to locate as much of the current input
field on the terminal display.
Soft always positions on a quadrant boundary regardless of input field boundaries.
Viewing keys are enabled.
Hard is the same as Soft except the viewing keys are disabled.
Lock locks the terminal display origin (upper left corner) to fixed row and column
(x,y) coordinates in the host display. The coordinates are zero-based.
Font Size
These check boxes enable (checked) or disable (unchecked) the display of characters in
double high and double wide font.
4-4
Twin Client Reference
• June, 2005
Setup Using Twin Client Manager
Key Click
This option is used to automatically transmit a keystroke to the 5250 host when the 5250
field matches the selected attribute. The automatic keystroke generation can be based on
whether the input is scanned, or keyed, or both.
Printer Type
This scrolling list selects the attached printer type. The default value is none, indicating
no printer is attached.
3270 Settings
Select the 3270 emulation setup by clicking on the Settings menu and then the
Emulation menu, as shown below.
Then click on the 3270 selection, as shown below.
Click on OK after the selection is made, and return to the main Twin Client Manager
menu. The standard settings tab will now reflect the settings for 3270 emulation.
Twin Client Reference • June, 2005
4-5
Standard Setup
Quadrant Mode
This scrolling list option defines the rules by which the terminal display is positioned in
the larger host display. As defined by Twin Client, quadrants are fixed position
"windows" in the host display, and the terminal display is located on whatever quadrant
contains the current cursor position.
Off disables quadrant processing and Twin Client simply centers the current host
input field in the terminal display.
On enables quadrant processing. However, input fields that cross quadrant
boundaries result in a shift to the left in order to locate as much of the current input
field on the terminal display.
Soft always positions on a quadrant boundary regardless of input field boundaries.
Viewing keys are enabled.
Hard is the same as Soft except the viewing keys are disabled.
Lock locks the terminal display origin (upper left corner) to fixed row and column
(x,y) coordinates in the host display. The coordinates are zero-based.
Double High and Double Wide Font
These check boxes enable (checked) or disable (unchecked) the display of characters in
the double-high and double-wide fonts.
4-6
Twin Client Reference
• June, 2005
Terminal Setup Using Twin Client Menus
Key Click
This option is used to automatically transmit a keystroke to the 3270 host when the 3270
field matches the selected attribute. The automatic keystroke generation can be based on
whether the input is scanned, or keyed, or both.
Printer Type
This scrolling list selects the attached printer type. The default value is none, indicating
no printer is attached.
Terminal Setup Using Twin Client Menus
The Twin Client terminal software provides an internal menu system for configuring
certain parameters on the terminal. To access this menu system, press uppercase C at the
startup screen as shown in the following figure.
Twin Client
© 1991-2005, Connect, Inc.
Press Any Key
The next screen displays the following functions. Cursor to the appropriate function and
press Enter.
EDIT MENU OPTIONS
Edit Mobile Unit IP
Edit Server/Host IP
Edit Radio Option
Edit License Key
Switch Client Modes
Set Contrast
Run Client Emulator
Exit to OS
Use the Up-Arrow and Down-Arrow keys to navigate the menu, and press Enter to select
the highlighted option. Each menu option is described below.
Editing the Mobile Unit IP
The IP list contains the terminal IP address, the Subnet Mask and the Router IP address.
Enter the appropriate address and select <F3> to save and/or <F7> to Quit.
IP 206.232.71.38
SN 255.255.255.0
RT 206.232.71.1
<F3> Save <F7> Quit
Editing the Host IP
If the host IP address(es) were not pre-configured as described in the Setting the Servers
section of Configuring the Manager, or if you wish to change those settings using the
terminal menus, select Edit Host List and enter up to four Host IP addresses as required.
Twin Client Reference • June, 2005
4-7
Standard Setup
Host 0
IP 206.183.67.155
Port 23__
<F3> Save <F7> Quit
Press F3 to save the configurations.
Editing the Radio Option
This function acts as a password to join the radio network. Terminals associating with an
Access Point must supply a matching value, determined by their configurations, or their
association requests will be ignored.
ID tsunami____________
<F3> Save
<F7> Quit WEP Support
To activate WEP, the AP must have WEP enabled and supply matching WEP keys.
Note: 64-bit and 128-bit encryption are supported. Valid keys for 64-bit are 5 character
ASCII or 10 character HEX keys starting with '0x'. Valid keys for 128-bit are 13
character ASCII or 26 character HEX keys starting with '0x'.
1. Press Enter or F3 after entering the ID screen.
2. A 'WEP? (Y or N)' prompt appears to enable WEP. Entering 'N' or 'n' closes the
screen and does not enable WEP. Entering 'Y' or 'y' prompts for the transmit WEP
key.
3. Enter a number between 1 and 4 to select the transmit key.
Tx Key (1): 1 <Enter>
4. Press Enter after each entry.
Acceptable keys:
Key 1: xyzab <Enter>
Key 2: abcde <Enter>
Key 3: qwerty <Enter>
Key 4: zxcvb <Enter>
or
Key 1: 0x123456789A <Enter>
Key 2: 0x123456789B <Enter>
Key 3: 0x123456789C <Enter>
Key 4: 0x123456789D <Enter>
5. Blank keys are allowed as long as they are not the transmit keys.
INVALID KEY
Eg: Tx Key (1): 2 <Enter>
Key 1: xyzab <Enter>
Key 2: <Enter>
Key 3: qwerty <Enter>
Key 4: zxcvb <Enter>
Acceptable keys:
4-8
Twin Client Reference
• June, 2005
Terminal Setup Using Twin Client Menus
Eg: Tx Key (1): 4 <Enter>
Key 1: xyzab <Enter>
Key 2: <Enter>
Key 3: qwerty <Enter>
Key 4: zxcvb <Enter>
6. Press Enter or F3 to save changes or F7 to quit without saving.
Note: A reboot is required before radio changes will take effect.
Editing the License Key
The client software can be authorized automatically, as described in the next section,
Authorizing Twin Client. This menu option permits authorization of each terminal
manually. Select Edit Authorization to obtain the terminal's Identification Code, used to
obtain the Authorization code from the Connect web site, as described in the next section.
The 12-digit value displayed at the top of the terminal screen is the Identification Code
for the terminal.
00A0F826E614
Authorization
______________
not authorized
<F3> Save <F7> Quit
Type the authorization code into the field as it appears on the WEB site. Punctuation
characters, such as the hyphen (-), are required. Press F3 to save the authorization code.
Switching Client Modes
Switch to the server based Client Mode by selecting this option.
Setting the Contrast
Adjust the contrast as required by pressing the right and left arrow keys.
The Contrast screen appears as follows.
CONTRAST
F3> Save <F7>Quit
Running the Client Emulator
After all desired changes have been made, select the Run Emulator option to return to
the Twin Client main menu. Then press any key to establish the Telnet session and begin
emulation. Refer to the Chapter 3 sub-section, Starting a Telnet Session, for further
instructions.
Twin Client Reference • June, 2005
4-9
Standard Setup
Exiting to OS
After all changes have been made, scroll to exit. Selecting exit will bring you to the A:>
prompt.
Authorizing Twin Client
Each PowerNet Twin Client will run for 30 minutes at a time without authorization.
Uninterrupted operation for a production environment is the result of authorizing the
software.
The Twin Client Manager can automatically authorize the terminal over the wireless
network if the following requirements are met:
• A PC running Twin Client Manager is connected to the wire LAN segment with at
least one access point within range of the terminal.
• The System ID of the PC on which Twin Client Manager is installed has been used to
obtain a site license Authorization code from the Connect web site.
To obtain the System ID of the Twin Client Manager, click on the Authorization option
in the Tools menu, as shown below.
The Authorization window is displayed as shown below.
4-10
Twin Client Reference
• June, 2005
Authorizing Twin Client
Your System ID appears in the first box of the screen.
Go to http://www.connectrf.com. Click on Partner Services. Click on the Generate
Authorization icon at the top of the page. Follow the directions on the web site.
Authorized Terminals
The number of terminals authorized, the number of terminals in use, and the number of
terminals remaining is provided in the Authorized Terminals box on the lower left side of
the screen.
Click on the Details button to number the options in the screen below in the order of your
priority.
Note: The terminal may or may not be able to utilize the Formatter feature depending on
its authorization codes.
Twin Client Reference • June, 2005
4-11
Standard Setup
Click on an option and move it using the Up and Down buttons.
Click on OK when finished.
The Manual Authorization button is an alternate method of obtaining an authorization
code for a terminal. This method does not utilize Airloader, as does the other method.
Click on this button, manually enter your mac address in the screen that appears, and
click on OK. This enables you to generate individual authorization codes.
4-12
Twin Client Reference
• June, 2005
Authorizing Twin Client
Add Licenses
The Add Licenses feature is used when adding additional licenses to an already site
licensed Twin Client Manager. (i.e. Twin Client Manager is licensed for 10, and the
customer purchases another 10 licenses to make a total of 20.)
From Twin Client Manager, choose Authorization from under the Tools menu. Click on
the Add Licenses button.
A pop-up box appears with the machine ID and a space for the additional licenses
authorization code. Enter the additional license’s authorization code and click on OK.
Use the machine ID in the pop-up box instead of the original machine ID to get your
authorization code.
If adding users, click on the Add Licenses button before generating the authorization
code to get the most current machine ID.
Twin Client Reference • June, 2005
4-13
Standard Setup
Transfer Authorization
The Transfer Licenses feature is used when moving a site license from one PC to
another. After Twin Client Manager is installed on a new PC, you will need the
system/machine ID for it.
From Twin Client Manager, select Authorization from under the Tools menu.
Click on the Transfer Authorization button on the old PC. You will be asked for the new
system ID. Enter this new system ID. It will generate an authorization code for the new
PC's Twin Client Manager.
Note: This feature only works if there are licenses remaining on the old PC.
4-14
Twin Client Reference
• June, 2005
Authorizing Twin Client
Listing
Click on the Listing button to view authorization codes used along with corresponding
serial numbers.
Click on OK when finished.
Click on the Close button when finished.
Twin Client Reference • June, 2005
4-15
Standard Setup
This page is intentionally blank.
4-16
Twin Client Reference
• June, 2005
Chapter 5 • Advanced Setup
The Twin Client permits the customization of all aspects of terminal operation without
custom programming. This chapter describes all of the advanced setup options.
Additional advanced customization features, such as using the Object Editors, are
described in Chapter 6.
Selecting the Advanced Setup
The Twin Client Manager is installed in the Standard Setup mode. To change to the
Advanced mode, click on the View menu and then on Advanced.
As a result, a new set of tabs is displayed, as shown below.
The following sections in this chapter describe each of the tabs and the options within
each tab.
Twin Client Reference
• June, 2005
5-1
Advanced Setup
Customizing the Keyboard
Clicking on the Keyboard tab displays the setup options related to the terminal keyboard
and its operation.
End Key
This scrolling list selection is used to set the terminal key that terminates both the host
connection and the wireless session. The default is PF10.
Auto Send Key
This scrolling list selection is used to set the keystroke to be sent automatically by the
terminal when an input field on the terminal is filled with keyed input. That is, if an input
field is 9 characters long, and 9 characters are manually keyed into the field, the Auto
Send key is automatically transmitted with the 9 characters. The default is tab. Selecting
noop disables this feature.
Note: Selecting the Length Check option on the Scanner tab disables the Auto Send Key.
5-2
Twin Client Reference
•
June, 2005
Customizing the Keyboard
Key Click
This check box enables (checked) or disables (unchecked) audible key clicks from the
terminal. Default is on (checked).
Case Conversion
This scrolling list selection allows automatic conversion of keyed input to upper or lower
case. The default value is none, meaning no conversion takes place.
Mapping Object
This feature of Twin Client allows for custom keyboard development. For example, the
tab key can changed to generate a PF4. This is an advanced integration tool and its use is
described in Chapter 6.
Macro Object (VT/HP Only)
This feature is used to assign a key sequence to a specific terminal key. For example, the
PF1 key can be set to generate a sequence such as receiving. This is an advanced
integration tool and its use is described in Chapter 6.
Mode (VT/HP Only)
This scrolling list selection controls the transmission characteristics of the VT/HP
emulations. In char mode, each keystroke generates an individual transmission. In block
mode, a transmission takes place only after a control key, such as Enter or a PF key, is
depressed. The block mode is more efficient. Refer to Chapter 6, Advanced Display
Options for VT/HP, for more details on setting block mode operation.
Note: When set to char mode, the Collection timer value in the Timers tab should be set
to between 30 and 50 milliseconds for maximum performance.
Auto EOF (3270 only)
This check box option enables (checked) or disables (unchecked) the automatic erasure of
all data in a field prior to keyed or scanned data input. The default value is disabled.
Clear First (3270 only)
This check box option enables (checked) or disables (unchecked) the automatic erasure of
all data in a field prior to keyed or scanned data input. The default value is disabled.
Advanced (3270 only)
Clicking the Advanced button brings up the Advanced 3270 Keyboard screen and
provides a variety of special key generation options. This is an advanced integration tool
and its use is described in Chapter 6.
Twin Client Reference •
June, 2005
5-3
Advanced Setup
Customizing the Display
Clicking on the Display tab shows the options related to the terminal display and its
operation.
Quadrant Mode
This scrolling list option defines the rules by which the terminal display is positioned in
the larger host display. As defined by Twin Client, quadrants are fixed position
"windows" in the host display, and the terminal display is located on whatever quadrant
contains the current cursor position.
Off disables quadrant processing and Twin Client simply centers the current host
input field in the terminal display.
On enables quadrant processing. However, input fields that cross quadrant
boundaries result in a shift to the left in order to locate as much of the current input
field on the terminal display.
Soft always positions on a quadrant boundary regardless of input field boundaries.
Viewing keys are enabled.
Hard is the same as Soft except the viewing keys are disabled.
Lock locks the terminal display origin (upper left corner) to fixed row and column
(x,y) coordinates in the host display. The coordinates are zero-based.
5-4
Twin Client Reference
•
June, 2005
Customizing the Display
Lock Row defines the Y coordinate for display position locking. Range is zero (0) to
maximum number of rows on the host screen. Default is zero (0).
Lock Column defines the X coordinate for display position locking. Range is zero
(0) to the maximum number of columns on the host screen. Default is zero (0).
Scroll Mode
This scrolling list option selects the rule used for moving the terminal display within the
host display using the viewing keys.
Half scrolls the terminal display in half-screen increments. For example, given a 16column screen, the screen is scrolled left and right 8 columns at a time.
Full scrolls the terminal display in full screen increments. For example, given a 16-
column screen, the screen is scrolled left and right 16 columns at a time.
Language
This scrolling list option selects the display character mapping and the translation table
used for error messages displayed on the terminal. The default value is English. The file
umsgs.txt, which is installed with Twin Client, contains all of the current language
translations.
In the event a specific language is not translated, or if a specific message is not correctly
translated, visit the Connect web site at http://www.connectrf.com and check the Support
page for a related Tech Note. If the issue has not been addressed, email
[email protected] and request a Product Change Request (PCR).
Cursor Appearance
This scrolling list option selects the manner in which the cursor is displayed on the
terminal. The default value is hard.
Type Appearance
soft Blinking Underscore (_)
hard Blinking Block „
hide None
Mapping Object
This feature is used to modify the displayed character set. This is an advanced integration
option and its use is described in Chapter 6.
Dialog Object
This feature is used to build session automation scripts, and is an advanced integration
option described in Chapter 6.
Twin Client Reference •
June, 2005
5-5
Advanced Setup
Formatting
This feature is used to re-format the host display onto the terminal display. This is an
advanced integration option and is described in Chapter 6.
Relocation Group
This option group allows rows of the host display to be relocated automatically. This
option is particularly useful when the application generates important error messages on a
specific row that is not necessarily within the terminal's display area
Source
Defines the starting row (zero-based) in the host display that is relocated to the
destination row of the host display. The default is zero (0).
Destination
Defines the starting source row location (zero-based) in the host display. Default is zero
(0).
Row Count
Specifies the number of host display rows to be relocated, starting with the row defined
by the Source option and continuing from top to bottom of the display. The default, zero
(0), disables row relocation.
Move Blank
This check box enables unconditional relocation (checked), or enables relocation only
when data is present on the source row or rows (unchecked). The default is unchecked.
Reverse Video
This check box enables (checked) or disables (unchecked) the processing of the reverse
video display attribute on the terminal. The default value is on (checked).
Wait Message
This check box enables (checked) or disables (unchecked) the display of the message
Waiting for Data on the terminal display. This message is used to indicate that the
terminal has transmitted data to the host application and is waiting for a response. The
default value is enabled (checked).
Default Data (3270/5250 only)
This check box enables (checked) or disables (unchecked) editing of data present in the
current input field prior to entry of new data by the terminal operator.
5-6
Twin Client Reference
•
June, 2005
Customizing the Scanner
Double High and Double Wide
These check boxes enable (checked) or disable (unchecked) the display of characters on
the terminal screen in double high and double wide fonts, respectively.
Advanced (VT/HP only)
This button accesses setup options for controlling all aspects of VT display attribute
mapping and masking. This is an advanced integration tool and its use is described in
Chapter 6.
Customizing the Scanner
Clicking on the Scanner tab shows the options related to the terminal scanner and its
operation.
Send Key
This scrolling list option defines the control key automatically transmitted with scanned
data. The list of keys depends on the type of emulation in use. The noop key indicates
that no automatic control key will be sent. The default value is Enter.
Twin Client Reference •
June, 2005
5-7
Advanced Setup
Scan Ahead
This scrolling list option defines the number of scans that can be transmitted by the
terminal without a response from the host system. The maximum is 24. The default
is 1.
Set to 0, scan ahead is disabled and you cannot scan again until the host response has
been received.
Set to 1, there is no scan ahead limit.
Set to 2 and above, and the software will let you scan that many times until a host
response is received. So if you set it for 3, it will allow you to scan only 2 more times
before the host responds to the first scan.
Length Check
With Length Check off, and Auto Enter key set to "noop": Keyed or scanned input
that is equal to or greater than the field length results in an error "Entry Too Long" and no
data is transmitted.
With Length Check off, and Auto Enter key set to anything other than "noop":
a. Keyed input equal to the field length: The data and the specified Auto Enter key are
transmitted.
b. Keyed input greater than field length: This is not possible, due to a) above.
c. Scanned input equal to or greater than the field length: The data is transmitted. If the
data is greater than the field length, then that data is distributed among the subsequent
input fields and the Scan Termination key is transmitted (unless it too is set to
"noop").
With Length Check on: The Auto Enter key and its functionality are disabled for both
scanned and keyed input.
There are specific functionalities related to the various settings of length checking and the
Auto Enter key. Setting the Auto Enter key to "noop" disables the Auto Enter function
(i.e., automatic transmission of data when the field is filled or overfilled) for both
scanned and keyed input. When it is set to anything other than "noop", keyed and
scanned input is distinguished and the Auto Enter key is effective only for keyed input.
Scanned data that is equal to or greater than the field length is terminated with the Scan
Termination key instead of the Auto Enter key.
Note: Enabling Length Check disables the Truncation option (described below).
Truncation
This check box option enables (checked) or disables (unchecked) the automatic
truncation of scanned data that is greater than the length of the input field. With both
Truncation and Length Checking disabled, oversized scans are automatically applied to
subsequent input fields as needed. If either option is enabled, this automatic application is
disabled. The default value is disabled (unchecked).
5-8
Twin Client Reference
•
June, 2005
External Scanner Setup
Stripping
This scrolling list option controls the rule for automatically removing trailing spaces and
underscore characters. The rules are defined as follows:
Rule
off
space
score
both
Operation
No stripping is performed.
Trailing spaces are stripped.
Trailing underscores are stripped.
Both trailing spaces and underscores are stripped.
Binary-128
This check box enables (checked) or disables (unchecked) the processing of binary code
128 bar codes on the terminal. The default value is enabled (checked).
Caution: If this option is disabled and binary-128 barcodes are used, the results are
unpredictable.
Data Mapping, Data Editor, and Decoder Control
These are advanced integration tools and are described in Chapter 6.
Scanner Type
This scrolling list option defines the type of special scanner attachment in use, if present.
External Scanner Setup
RF terminals can be ordered with an Internal scanner or they can also support an external
scanner. The external scanner is connected to the bottom of the terminal through the
serial port. This requires the RS232 adapter be installed. The external scanner can be
made to work even if an internal scanner is present. However, scanner decoder controls
only apply to the internal scanner as we only have access to the internal decoder.
The external scanner must be a serial based scanner. These are scanners that have on
board decoder hardware/software and output their signals by normal RS232 signaling
methods. These external scanners are controlled by their respective manufacturer’s
program controls provided in the manual accompanying the scanner from the
manufacturer.
The following is an example of a setup for an RF terminal.
This is the order in which to set up the scanner.
1 - (SET RS-232C DEFAULTS)
2 - (SET ALL DEFAULTS)
3 - RS-232 HOST BAUD RATE (9600)
4 - RS-232 HOST PARITY (NONE)
Twin Client Reference •
June, 2005
5-9
Advanced Setup
5 - RS-232 HOST DATA TRANSMISSION FORMATS (<DATA><SUFFIX>)
6 - RS-232 HOST PREFIX/SUFFIX VALUES (SUFFIX)
7 - RS-232 HOST PREFIX/SUFFIX VALUES (<1><0><1><3>)
Setting Log Levels
The terminal maintains a logging facility that can be used by Technical Support and
Engineering to assist in problem resolution. These levels should always be set to zero (0).
Customizing Timers
Clicking on the Timers tab shows the options related to the terminal timers, as shown
below.
5-10
Twin Client Reference
•
June, 2005
Customizing Timers
Timers Group
Radio
This numeric input field defines the length of time, in seconds, during which the terminal
activates the radio and waits for a response from the host application. After the time is
exceeded, an error message is displayed on the terminal. The default value is 120.
Power
This numeric input field defines the length of the time, in seconds, after which inactivity
of the scanner, keyboard, or radio results in a power saving shutdown of the terminal. The
default is 300 (5 minutes).
Backlight
This numeric input field defines the length of time, in seconds, during which the
terminal’s display backlight remains on after keyboard or scanner input. When set to a
value other than 0, the terminal turns on the backlight for the amount of time specified.
Backlight use reduces battery life. The default value is 5.
Keepalive (3270/5250 only)
This option group circumvents host application connection timeouts by automatically
generating the selected keystroke when the terminal is inactive for the specified period of
time, in minutes.
Twin Client Reference •
June, 2005
5-11
Advanced Setup
Collection Timer (VT/HP only)
This scrolling list option specifies the number of milliseconds the terminal waits for
inactivity from the host before processing received data. This feature is useful in
situations where the application and network latency fragments host transmissions to the
terminal, and also when host applications generate intermediate displays that are not
used. The default value is 100.
Note: For maximum performance, adjust the collection time to 30-50ms when Mode on
the Keyboard tab is set to char.
Customizing Alarms
Clicking on the Alarm tab shows the options related to the terminal alarm mechanisms, as
shown below.
Mode
This scrolling list option defines the operation of the audible alarm and scanner light on
the terminal. Default is bell.
• Off disables the audible alarm.
• Bell enables the audible alarm as a double beep.
• Flash enables the scan indicator light as the alarm - no audible alarm sounds.
• Both enables the double beep and the scan indicator light as the alarm.
• Spec1 enables the audible alarm as a single beep.
• Spec2 enables a single beep and the scan indicator light as the alarm.
5-12
Twin Client Reference
•
June, 2005
Customizing Alarms
Volume
This scrolling list option set the volume of the audible alarm. The default is setting is hi.
Duration & Frequency
The next two options, duration and frequency, are used to make a distinction between
alarms and scan decode tones when the Mode is set to spec1 or spec2.
Duration
This numeric entry field defines the length of the alarm sound in milliseconds. The
default is 150.
Frequency
This numeric entry field defines the frequency of the audible alarm in Hertz. The default,
zero (0) selects the terminal's factory-set default which is terminal model dependent. The
default value is 2048.
Allow Multiple
This check box enables (checked) or disables (unchecked) multiple alarms in a single
host transmission.
Scan Duration & Frequency
The next two options, scan duration and frequency, relate to the tones generated when the
scan decoder successfully identifies a symbology.
Scan Duration
This numeric input field defines the duration of the tone generated by a successful scan
decode, in milliseconds. The default is 300.
Scan Frequency
This numeric entry field defines the frequency of the scan decode tone in Hertz. The
default, zero (0), selects the terminal's factory-set default which is terminal model
dependent.
By Attribute (3270 only)
This scrolling list entry defines how 3270 field attributes can be used to generate alarms.
The choices are off (the default), pen for the light pen attribute, num for numeric
attribute, hi for high intensity attribute, and hal for high intensity and light pen attributes.
Protected
This check box enables (checked) or disables (unchecked) the processing of the field
attribute into audible alarms for all protected fields on the display.
Twin Client Reference •
June, 2005
5-13
Advanced Setup
Unprotected
This check box enables (checked) or disables (unchecked) the processing of the field
attribute into audible alarms for all unprotected fields on the display.
Alternate (5250 only)
This check box enables (checked) or disables (unchecked) the conversion of a single digit
character at a specified row and column on the 5250 display into the corresponding
number of audible alarms.
Row
This numeric input field specifies the zero-based row number in the 5250 display of the
alternate alarm digit.
Column
This numeric input field specifies the zero-based row number in the 5250 display of the
alternate alarm digit.
Customizing Printers
Clicking on the Printer tab shows the options related to the terminal printer, as shown
below.
5-14
Twin Client Reference
•
June, 2005
Customizing Printers
Type
This scrolling list option defines the type of printer attached to the terminal. The default
is none.
Init Object
This feature allows printer initialization commands to be sent to the terminal immediately
after the terminal establishes a session. This is an advanced integration tool and is
described in Chapter 6.
Flag Byte, Row, Column, and Clear Key (3270,5250 only)
This group of options provides 3270 and 5250 host application direct control over the
terminal printer. See the Start and End later in this section for an alternate method.
VT/HP applications rely on standard escape sequences for the printing function.
Flag Byte
This numeric input field is a decimal value that corresponds to the ASCII-converted
value of an EBCDIC character generated by the host application. When the Flag Byte is
set to a non-zero value, the terminal checks the host display for the value at the specified
row and column (see Flag Row and Flag Column below). If the Flag Byte is present, all
data in the display that follows the Flag Byte is routed directly to the printer, up to the
next occurrence of a Flag Byte value in the display or else the end of the display.
Flag Row
This numeric input field specifies the row (zero-based, range of 0 to23) where the Flag
Byte (defined above) is located.
Flag Column
This numeric input field specifies the column (zero-based, range of 0 to79) where the
Flag Byte (defined above) is located.
Clear Key
This scrolling list option defines the keystroke transmitted by the terminal after printing
has completed. Set the key to noop to disable transmission.
Start and End (3270 and 5250 only)
This option group provides the host application direct control over the terminal printer.
Start
Specifies a unique character sequence that, when encountered in the host display,
indicates that all subsequent characters up to but not including the End character
sequence are to be transmitted to the printer attached to the terminal. The default value is
blank which also indicates that this option is not in use.
Twin Client Reference •
June, 2005
5-15
Advanced Setup
Note:
The print data limit is 1.5 K.
End
Specifies a unique character sequence that terminates collection of data from the host
display area for transmission to the printer attached to the terminal. The default value is
blank which also indicates that this option is not in use.
Start and End Convert (3270/5250 only)
This option group provides for conversion of print data collected with the Start and End
option group from ASCII characters in hexadecimal format (0-9 and A-F) to binary. The
feature allows binary data that might otherwise interfere with the emulation to be
included in the display area. The host application is responsible for generating the
hexadecimal data.
Start Convert
Specifies a unique character sequence (ASCII-converted) within the print data collected
with the Start and End options that indicates the subsequent character pairs are
hexadecimal values that are converted to binary. A blank value, default, indicates that this
option is not in use.
End Convert
Specifies a unique character sequence (ASCII-converted) that terminates binary
conversion. Default, blank, indicates that this option is not in use.
LXE Option (3270/5250 only)
This check box enables (checked) or disables (unchecked) the processing of print data
embedded in the datastream according to LXE printing rules.
Convert Flag Byte and Conversion (3270 only)
This option group defines the conversion of a single character (Convert Flag Byte) found
in the 3270 print data, to a printer control sequence defined by the Conversion scroll list.
Convert Flag Byte
This numeric input field defines an ASCII value, in decimal, that will be converted to a
printer control sequence as defined by the Conversion option. The default value is zero
(0), which disables conversion.
Conversion
Specifies what the Flag Byte is converted to. The options are crnl, cr, and nl, which
represent ASCII carriage return new line, carriage return, and new line, respectively. The
default value is crnl.
5-16
Twin Client Reference
•
June, 2005
Miscellaneous Customizations
Miscellaneous Customizations
Clicking on the Misc tab shows the following options window.
Extended Command Group (3270 and 5250 only)
This option group provides 3270 and 5250 host applications with the same extended
command set available to VT/HP applications. Refer to Chapter 6 for a detailed
description of the Extended Commands.
Start
Specifies a unique character sequence that, when encountered within the host display,
indicates that all subsequent characters up to but not including the End sequence, are to
be interpreted as an Extended Command. Default, blank, indicates that the option is not
in use.
End
Specifies a unique character sequence that terminates the Extended Command.
Data Stream Group (3270 only)
Send All MDT
This check box enables (checked) or disables (unchecked) the transmission of all fields
with the MDT (Modified Data Tag) bit set. When disabled, only unprotected fields are
transmitted. The default is enabled, which transmits all fields with the MDT set.
Send NULL
This check box enables (checked) or disables (unchecked) the transmission of NULL
characters to the host system. The default value is disabled.
Twin Client Reference •
June, 2005
5-17
Advanced Setup
Note: For AS400 hosts, this option must be unchecked.
Enable TN3270E
If box is checked, will negotiate using TN3270E rules (see RFC 2355).
If box is not checked, will NOT negotiate TN3270E and will use IBM 3278 Mod 2.
Answerback (VT/HP only)
This text input field defines the response returned to the host application when the
answerback command (as defined under VT/HP emulation) is received. If this value is
left blank, the terminal automatically returns an ASCII string corresponding to the
emulation in use (vt100, vt220, or hp700).
Non-graphic characters may be embedded in the answerback field using the escape
sequence \nnn , where the backslash is followed by three digits representing the octal
value.
$1 = terminal number. IP terminals = last two octets of the IP address.
Spectrum One = 065-511
$M = 4 character terminal model number (i.e., "7035")
Inserting the sequences “$A”, “$B”, “$C”, and “$D” into the answerback string results in
a substitution of four octets, three octets, two octets, and the last octet of the terminal IP
address, respectively, as shown below.
$A - all four octets of the IP address (206.183.067.226)
$B - the last 3 octets (183.067.226)
$C - the last 2 octets (067.226, same as $1)
$D - the last octet (226)
Given a terminal with an IP address of 206.183.67.226, the following examples
demonstrate how substitution and non-graphic escape sequences are processed.
Answerback
Hello World
$A
RF$A
RF$A\015
$B
RF$B
RF$B\015
$C
RF$C
RF$C\015
$D
RF$D
RF$D\015
5-18
Data Sent in Response to Answerback Command
Hello World
206.183.067.226
RF206.183.067.226
RF206.183.067.226<carriage return>
183.067.226
RF183.067.226
RF183.067.226<carriage return>
067.226
RF067.226
RF067.226<carriage return>
226
RF226
RF226<carriage return>
Twin Client Reference
•
June, 2005
Chapter 6 • Advanced Integration
This chapter describes the use of the advanced integration features built in to the Twin
Client. These features make it possible to tailor Twin Client operation to meet special
customer requirements without custom programming.
Integration objects are used to implement the Twin Client advanced integration
capability. An editor is used to create and modify each object, and the objects are
associated with a terminal configuration using the Advanced setup options described in
the previous chapter. The objects then become part of the terminal's software
configuration and as a result are supported by the powerful Airloader Auto-Configuration
tools described in Chapter 8.
Clicking on the Object Editors menu of the Twin Client Manager displays the editor
menu.
The following sections describe the use of each object, how to create the object, and how
to assign the object to a terminal configuration using the Advanced Setup options.
A detailed description of the Extended Commands, which are used by applications to
dynamically control the terminal scanner and keyboard, is included in this chapter. The
advanced emulation-specific configuration options to which the previous chapter refers
are also described here.
Keyboard/Mapping
The Keyboard/Mapping object is used to change the functionality of the terminal
keyboard. This feature is most often used to simplify keyboard usage and reduce operator
workload. It is also used to reduce re-training requirements when introducing new
terminal models.
Twin Client Reference
• June, 2005
6-1
Advanced Integration
The need for keyboard mapping is a result of the size-restricted keypads common to all
portable terminal devices. Compensating for the physical limitations, the manufacturer
uses state modifier keys to expand the functionality of the keypad. As a result, many keys
(e.g., the Up-Arrow key) require the operator to press two or more keys to emulate a
single keystroke. Because many applications tend to rely heavily on a small group of
keys, it is advantageous to map those frequently used keys to single key strokes, thus
increasing both productivity and user acceptance.
Creating the Object
Create the object by clicking on Object Editors, then click on Keyboard/Mapping and
select a terminal type.
Click on the desired terminal model and click on OK, which starts the keyboard mapper
for the selected terminal model.
The Keyboard Mapper screen provides a mock-up of a keypad on the left side of the
window, and options for key remapping on the right. By clicking on a key on the keypad
mock-up, the available options that apply to that key appear on the right.
The first column on the right side of the window, entitled Transmit, defines the emulation
key assigned to the highlighted keypad button in each of the available keyboard states
(unshifted, shifted, etc.). Each modified key state is initially blank, indicating that the
Twin Client default is in effect and no changes will be made to that key or its Mode of
operation.
6-2
Twin Client Reference
• June, 2005
Keyboard/Mapping
After a key is selected, the Mode options change depending on the key selection. The
Mode column defines the action taken by the selected key combination.
The table of mode options, and their effect, is as follows.
xmit
Transmits the key.
noop
Disables the key.
edleft
Non-destructive backspace (moves) to the left of the cursor within a field.
edrite
Non-destructive space (moves) to the right of the cursor within a field.
edbksp
Destructive backspace (moves) to the left of the cursor within a field.
edeeof
Erases from current position to end of field.
edefld
Erases entire field.
lhelp
Displays terminal ID, date, time, and terminal software version number.
scan
Activates the scanner.
Saving and Assigning the Object
Save the object by clicking on File, and Save As, and then enter a name. For the
purposes of this example, the name is vt.
Twin Client Reference • June, 2005
6-3
Advanced Integration
Then click on Save. Return to the Twin Client Manager menus by clicking on the
button at the upper right corner of the Keyboard Mapper window.
Next, assign the object to a terminal configuration by opening a terminal configuration
from the File menu. Click on the advanced setup Keyboard tab, then on the Mapping
Object list button, and finally on the object name.
Save the updated terminal configuration by clicking on File, and then Save. The next
time the terminal is booted, the new configuration will be downloaded automatically and
the keyboard mapping will take effect.
Keyboard Macros
The Keyboard/Macro object is used to assign sequences of characters to the VT/HP
programmable function keys. Using this feature, strings of characters can be assigned to a
single keystroke.
Creating the Object
Create the object by clicking on Object Editors, then Keyboard/Macros, and then enter
a file name. For the purposes of this example, the name is vt.
6-4
Twin Client Reference
• June, 2005
Keyboard Macros
Click on the Open button, and then click on the Yes button to create the new file.
The Notepad utility is then invoked. The Keyboard/Macro object is a text file with one
entry per line. Each entry uses the following format,
<keyname>=<macro string>;
where <keyname> is pf1 to pf24, and <macro string> is the macro text assigned to that
specific key. For example, to assign the text "vt100" followed by a carriage return to the
pf9 key, the entry is:
Note:
\015 represents the octal value for “carriage return”.
Saving and Assigning the Object
Save the object by clicking on File, then on Save, and then on Exit, which returns to the
Twin Client Manager menu.
Next, assign the object to a terminal configuration by opening a terminal configuration
from the File menu. Click on the advanced setup Keyboard tab, then on the Macro
Object list button, and finally on the object name.
Twin Client Reference • June, 2005
6-5
Advanced Integration
Save the updated terminal configuration by clicking on File, and then Save. The next
time the terminal is booted, the new configuration will be downloaded automatically and
the keyboard macro will take effect.
Scanner/Data Mapping
The Scanner/Data Mapping object defines barcode sequences that, when encountered in
scanned data, are automatically converted to emulator keystrokes. This feature can be
used to reduce or eliminate keyboard entry by the operator. That is, instead of pressing
the PF3 key to access a help screen, the operator scans a barcode that is mapped to the
keystroke.
Creating the Object
Create the object by clicking on Object Editors, then Scanner Data/Mapping, and then
enter a file name. For the purposes of this example, the name is vt.
Click on the Open button, and then click on the Yes button to create the new file.
The Notepad utility is then invoked. The Scanner/Data mapping object is a text file with
one entry per line. Each entry uses the following format,
<barcode>=<keystroke>;
6-6
Twin Client Reference
• June, 2005
Scanner/Data Mapping
where <barcode> is the scanned barcode and <keystroke> is the keystroke to send when
the barcode is scanned. The following example object demonstrates three scan data
mappings, including the mapping of barcode $H to the PF3 keystroke.
Note: The Scanner/Data Mapper accepts octal notation. See the example below.
#
# Sample scanner data mapping object
#
#Format is:
# barcode scanned = send this;
#For 5250 and 3270, only AID keys can be sent Pf1-Pf24, enter, clear, sysreq.
#When a barcode is scanned containing "001253" a Pf4 is sent to the host
001253=pf4;
ENT=enter;
TB=tab;
#Vt100 examples
#For a tab
#When a barcode is scanned containing "thisisatab" the tab is sent
#with octal values obtained from a standard ASCII chart
thisisatab=\009;
#For an enter
thisisanenter=\015;
#For pf1
*=\033[OP\015;
Saving and Assigning the Object
Save the object by clicking on File, then on Save, and then on Exit, which returns to the
Twin Client Manager menu.
Next, assign the object to a terminal configuration by opening a terminal configuration
from the File menu. Click on the advanced setup Scanner tab, then on the Data Mapping
Object list button, and finally on the object name.
Save the updated terminal configuration by clicking on File, and then Save. The next
time the terminal is booted, the new configuration will be downloaded automatically and
the scanner data mapping will take effect.
Twin Client Reference • June, 2005
6-7
Advanced Integration
Scanner/Data Editing
The Scanner/Data Editing object defines the rules for recognizing barcode patterns, and
then for performing automatic manipulations on the barcode before it is transmitted to the
host application. This feature is most often employed when upgrading wedge-based
systems.
Creating the Object
Create the object by clicking on Object Editors, then Scanner/Data Editing.
Barcode recognition is based on the size (length) and recognition specifiers. Once the
pattern is recognized, operation specifiers manipulate the barcode.
The recognition specifiers consist of the four characters shown in the following table:
A
N
*
=
Alpha character
Numeric character
Any character
Must match next character
The operation specifiers consist of the following constructs:
X
*
()
““
Delete character
Copy as is
Substitute
Insert
How these specifiers identify and manipulate the data is illustrated below.
Barcode
6-8
Size
Recognition
Operation
Result
PN-1245
7
AA=-NNNN
“F”*******
FPN-1245
5A5567BBAT
10
**********
**********”M”
5A5567BBATM
TGR87
5
=T=GAN*
**(S)**
TGS87
78-RHG
6
NN=-AAA
**X***
78RHG
Twin Client Reference
• June, 2005
Scan/Decoder Control
Saving and Assigning the Object
Save the object by clicking on File, and Save As, and then enter a name. For the
purposes of this example, the name is vt.
Then click on Save. Return to the Twin Client Manager menus by clicking on the
button at the upper right corner of the Scan Editor window.
Next, assign the object to a terminal configuration by opening a terminal configuration
from the File menu. Click on the advanced setup Scanner tab, then on the Data Editor
Object list button, and finally on the object name.
Save the updated terminal configuration by clicking on File, and then Save. The next
time the terminal is booted, the new configuration will be downloaded automatically and
the scan data editor object will take effect.
Scan/Decoder Control
The Scan/Decoder Control object modifies the operation of the scan decoder in the
terminal. Any of the supported symbologies can be enabled or disabled, and all of the
parameters associated with a specific symbology can be modified to meet specific
customer requirements.
This feature is used primarily to reduce errors and increase performance. For example, a
terminal used in a receiving application can be restricted to symbologies used only in the
receiving department, thus reducing the opportunity for scan decoder errors and, in many
cases, increasing scanner performance. As another example, the scan decoder can be
instructed to return a successful scan only when the barcode is of a certain length. As a
result, the opportunity for a scan decoder error is further reduced.
Twin Client Reference • June, 2005
6-9
Advanced Integration
Twin Client also allows the scanner to be controlled dynamically by the application. This
is accomplished through the use of the Extended Command set, which is described later
in this chapter.
Creating the Object
Create the object by clicking on Object Editors, then Scanner/Decoder Control.
The check box next to the symbology enables (checked) or disables (unchecked) the
symbology. The options for a specific symbology are available for modification by
highlighting the selected symbology.
Saving and Assigning the Object
Save the object by clicking on File, and Save As, and then enter a name. For the
purposes of this example, the name is vt.
6-10
Twin Client Reference
• June, 2005
Display/Mapping
Then click on Save. Return to the Twin Client Manager menus by clicking on the
button at the upper right corner of the Decoder Control window.
Next, assign the object to a terminal configuration by opening a terminal configuration
from the File menu. Click on the advanced setup Scanner tab, then on the Decoder
Control Object list button, and finally on the object name.
Save the updated terminal configuration by clicking on File, and then Save. The next
time the terminal is booted, the new configuration will be downloaded automatically and
the scan decoder control object will take effect.
Display/Mapping
The Display/Mapping object is used to correct variations between application character
sets and the terminal display character set. The terminal display uses the ISO-8859-1 font
set, which is an international standard adhered to by most, but not all, applications. The
display mapping is used to resolve any discrepancies.
Creating the Object
Create the object by clicking on Object Editors, then Display/Mapping, and then enter a
file name. For the purposes of this example, the name is vt.
Twin Client Reference • June, 2005
6-11
Advanced Integration
Click on the Open button, and then click on the Yes button to create the new file.
The Notepad utility is then invoked. The Display/Mapping object is a text file with one
entry per line. Each entry uses the following format,
<application char>=<ISO-8859-1 char>,xlat;
where <application char> is the hexadecimal value of the character transmitted by the
host application, and <ISO-8859-1 char> is the hexadecimal value of the desired
terminal display character, followed by a comma, the word xlat, and a semicolon. For the
purposes of this example, the English character e (0x65) will be converted to an umlaut ë
(0xEB) with the entry shown below. Note that that the two character hexadecimal values
must be preceded by 0x.
Saving and Assigning the Object
Save the object by clicking on File, then on Save, and then on Exit, which returns to the
Twin Client Manager menu.
Next, assign the object to a terminal configuration by opening a terminal configuration
from the File menu. Click on the advanced setup Display tab, then on the Mapping
Object list button, and finally on the object name.
6-12
Twin Client Reference
• June, 2005
Display/Formatting
Save the updated terminal configuration by clicking on File, and then Save. The next
time the terminal is booted, the new configuration will be downloaded automatically and
the Display/Mapping object will take effect.
Display/Formatting
The Display/Formatting object is used to make the host application interface easier to
use, without modifying the host application. Chapter 7 is devoted to the description of
this important integration feature.
Printer/Init
The Printer/Initialization object is used to send initialization commands to the printer at
the start of each terminal session. It can also be used to test printer operation.
Creating the Object
Create the object by clicking on Object Editors, then Printer/Init, and then enter a file
name. For the purposes of this example, the name is vt.
Click on the Open button, and then click on the Yes button to create the new file.
Twin Client Reference • June, 2005
6-13
Advanced Integration
The Notepad utility is then invoked. The printer/init object is a text file, allowing for the
entry of printer-specific commands. Refer to the documentation provided by the printer
manufacturer for instructions.
Saving and Assigning the Object
Save the object by clicking on File, then on Save, and then on Exit, which returns to the
Twin Client Manager menu.
Next, assign the object to a terminal configuration by opening a terminal configuration
from the File menu. Click on the advanced setup Printer tab, then on the Init Object list
button, and finally on the object name.
Save the updated terminal configuration by clicking on File, and then Save. The next
time the terminal is booted, the new configuration will be downloaded automatically and
the init object will be transmitted to the printer at the start of the next Telnet session.
Dialog
The Dialog object is a script used to automate difficult or repetitive user interactions with
the host application. It can be used to create terminal screens, collect input, generate
output, and make decisions based upon terminal keyboard or scanner input, and host
application data.
Creating the Object
Create the object by clicking on Object Editors, then Dialog. Commands selected from
scrolling list on the right are added or inserted into the scripting area on the left using the
click buttons between the two areas. The bottom left portion of the window is used to
collect arguments for those commands that require them.
6-14
Twin Client Reference
• June, 2005
Dialog
Commands and Arguments
Commands control the actions taken within the script. They can be used to interact both
with the host and the terminal, and to modify activity based on comparisons of both
terminal and host data. The following tables describe each command.
Label
Defines a target for the conditional branch commands Onfail,
Equal, If, Host State, Host Scan, and the unconditional
branch command, Goto.
Goto
Causes execution to begin unconditionally and immediately
at the named target Label.
On Fail
Upon detection of a system error, execution continues at the
named Label.
Equals
If the comparison is equal, branches to Label. Otherwise,
execution continues with the next command.
If
Set Var
Twin Client Reference • June, 2005
If the conditions of the comparison operator are true,
branches to Label. Otherwise, execution continues with the
next command. The numeric value comparison operators,
which treat the values being compared numerically, are =
(equal). != (not equal), > (greater than), and < (less than).
The string value comparison operators, which treat the values
as character strings, are $= (equal) and $!= (not equal)
Assigns a value to one of up to 36 variables.
6-15
Advanced Integration
Change Var
Concat
Adds characters to the end of a variable.
Session
Returns control of the session to the terminal operator. The
operator returns control to the dialog object, at the next line,
by pressing the key defined as the End Key in the Keyboard
tab.
Host On
Initiates a TCP/IP connection to the host system.
Host Off
Terminates the TCP/IP connection to the host system.
Host Scan
Host Update
Scans the host display for a value, and continues execution
at the named label if the value is found.
Refreshes the host display. This command is used after data
has been sent to the host that may change the display, and
prior to using the Host Scan or Host State conditional
branch commands, or a Host Copy command.
Host Send
Transmits data and/or a keystroke to the host.
Host Copy
Copies characters from the host display to a variable.
Host State
If the state of the session matches the value supplied,
execution begins at the named Label. The possible values
are inactive, meaning the host session has not been
established, and plu, which means the host session has
been established.
Settle
Term Enable
Term Clear
Term Display
Term Input
Term No Echo
Term Wait
Term Logoff
Exit
Sleep
Var Char
Log
Comment
6-16
Adds to or subtracts from the value of a variable.
Allows time for the host application to settle.
Initializes the terminal configuration parameters.
Clears the terminal display of all characters.
Puts a value or the value of a variable on the terminal display.
Prompts the terminal operator to input data.
Prompts the terminal operator to input data, which will not be
echoed on the terminal display.
Waits for any input from the terminal.
Terminates the connection to the wireless network.
Terminates execution of the dialog object.
Suspends all activity for the specified number of seconds.
Sets the character used internally by the dialog processor to
indicate the name of a variable. The character is normaLoglly
$. This command is used only when the first character of a
value used in one of the conditional branching commands
begins with a $.
Writes a message to the terminal log.
Inserts documentation in the dialog object.
Twin Client Reference
• June, 2005
Dialog
Adding Commands
The scrolling list box on the right side of the window is used to select a command. Click
on the desired command and then click on the Add button to add the command to the
dialog script.
All commands that require arguments prompt for them in the box at the lower left side of
the window. In the example above, the Term Display command requires a row number
and either a variable or a character string. In this case the display string is Hello World.
Note that the text entry field scrolls to the right so that text longer than the size of the box
can be entered.
Inserting and Deleting Commands
Click on the desired dialog line on the upper left side of the window to highlight the line,
then click on the Insert button to insert a new command above the selected line, or click
on the Delete button to remove the line.
Using Variables and Labels
The dialog object provides up to 36 variables to store temporary data collected during the
execution of the script.
Twin Client Reference • June, 2005
6-17
Advanced Integration
These variables can be compared to fixed values or other variables using the if command.
If the comparison is true, execution branches to the specified label.
Saving and Assigning the Object
Save the object by clicking on File, and Save As, and then enter a name. For the
purposes of this example, the name is vt.
6-18
Twin Client Reference
• June, 2005
Extended Commands
Then click on Save. Return to the Twin Client Manager menus by clicking on the
button at the upper right corner of the Decoder Control window.
Next, assign the object to a terminal configuration by opening a terminal configuration
from the File menu. Click on the advanced setup Display tab, then on the Dialog Object
list button, and finally on the object name.
Save the updated terminal configuration by clicking on File, and then Save. The next
time the terminal is booted, the new configuration will be downloaded automatically and
the dialog object will take effect.
Extended Commands
The host application can control the terminal's scanner and keyboard dynamically, while
the terminal is in session, by issuing the extended commands described in the following
sections.
Dynamic Decoder Control
The format and content of the commands that control the scan decoder are described in
the following sub-sections.
CODABAR Control
Extended Command:
<ESC>[?0;<state>;<minlen>;<maxlen>;0z
•
State:
Disable/enable codabar scanning. 0=disabled, 1=enabled.
•
Minlen:
Minimum valid barcode length. Valid values are 1–54.
Twin Client Reference • June, 2005
6-19
Advanced Integration
•
Maximum valid barcode length. The maximum length must be greater
than or equal to the minimum length. Valid values are 1–54.
Maxlen:
CODE 128
Extended Command:
<ESC>[?2;<state>;<minlen>;<maxlen>;0z
•
State:
Disable/enable code 128 scanning. 0=disabled, 1=enabled.
•
Minlen:
Specify minimum valid barcode length. Valid values are from 1 to 54.
•
Maxlen:
Specifies the maximum valid barcode length. The maximum length must
be greater than or equal to the minimum length. Valid values are from 1 to 54.
CODE 39
Extended Command:
<ESC>[?3;<state>;<minlen>;<maxlen>;<depend>z
•
State:
Disable/enable code 39 scanning. 0=disabled, 1=enabled.
•
Minlen:
Specifies the minimum valid barcode length. Valid values are from
1 to 54.
•
Maxlen:
•
Depend:
Specifies the maximum valid barcode length. The maximum length must
be greater than or equal to the minimum length. Valid values are from 1 to 54.
Disable/enable full ASCII code 39 interpretation. 0=disabled, 1=enabled.
INTERLEAVED 2 OF 5
Extended Command:
<ESC>[?7;<state>;<minlen>;<maxlen>;0z
•
State:
Disable/enable interleaved 2 of 5 scanning. 0=disabled, 1=enabled.
•
Minlen:
Minimum valid barcode length. Valid values range from 1 to 54.
•
Maximum valid barcode length. The maximum length must be greater
than or equal to the minimum length. Valid values range from 1–54.
Maxlen:
EAN-8/13
Extended Command:
<ESC>[?9;<state>;0;0;0z
•
State:
Disable/enable EAN-8/13 scanning. 0=disabled, 1=enabled.
PLESSEY/MSI
Extended Command:
<ESC>[?10;<state>;<minlen>;<maxlen>;<depend>z
6-20
•
State:
Disable/enable code MSI scanning. 0=disabled, 1=enabled.
•
Minlen:
Minimum valid barcode length. Valid values are from 4 to 54.
Twin Client Reference
• June, 2005
Extended Commands
•
Maximum valid barcode length. The maximum length must be greater
than or equal to the minimum length. Valid values are from 4 to 54.
•
Depend:
Maxlen:
Specifies the number of required check digits. Valid values are 0, 1, or 2.
UPC-A/E
Extended Command:
<ESC>[?13;<state>;0;0;0z
•
State:
Disable/enable UPC-A/E scanning. 0=disabled, 1=enabled.
Supplemental Barcode Handling (UPC/EAN) Options
Extended Command:
<ESC>[?12;<state>;<minlen>;<maxlen>;<depend>z
•
State:
•
Minlen:
•
Maxlen:
•
Depend:
This flag should always be set to one.
Specifies if two character supplementals are enabled/disabled (only
applies to transmit mode 1). 0=no codes with two character supplementals decoded,
1=codes with two character supplementals decoded.
Indicates if five character supplementals are enabled/disabled (only
applies to transmit mode 1). 0=no codes with five character supplementals decoded,
1=codes with five character supplementals decoded.
Specifies the supplemental transmit mode. 0=no supplementals
transmitted to host, supplemental enable/disable ignored. 1=only codes with the
appropriate supplemental (from minlen/maxlen) decoded. 2=all codes sent as is,
supplemental enable/disable ignored.
Disabling All Decoders
Extended Command:
<ESC>[?z
This command is used to disable all barcodes on the handheld. Typically this would be
issued before turning on an individual barcode type just to make sure of the state of the
active barcodes.
Input Mode Command
The input mode parameter sent from the application controls (via the host application)
whether the terminal accepts input from the keyboard, the scanner or both. The format of
this command is as follows:
<ESC>[!1;<mode>z
The mode parameter can be one of the following:
Twin Client Reference • June, 2005
6-21
Advanced Integration
Mode
Action
Description
0 (default)
Scan and Key
Data initially accepted from either the keyboard
or scanner. Scanning, allowed on a partially
keyed field, causes the keyed data to be
discarded and the scanned data to be accepted.
1
Scan or Key
Data initially accepted from either the keyboard
or scanner. Scanning is not allowed on a
partially keyed field. If the operator clears the
field then scanning is again allowed.
2
Scan Only
Data accepted only from the scanner. Use
caution when using this command, bad barcode
can block the user from completing input.
3
Key Only
Data accepted only from keyboard, scanner off.
Key Input Mode Command
The processing of keyed input can be controlled dynamically, while the terminal is in
session. The format of this command is as follows:
<ESC>[!2;<mode>z
The mode parameter can be one of the following.
Mode
Description
0 (default)
Accepts characters between 0x20 and 0x7F.
1
Accepts alphabetic characters only.
2
Accepts numeric characters only.
3
Accepts alphanumeric characters only.
For example, to allow keyboard input of numeric characters only, use the following
sequence:
<ESC>[!1;3z<ESC>[!2;2z
(HEX equivalent: 1B 5B 21 31 3B 33 7A 27 5B 21 32 3B 32 7A)
To reset the terminal back to normal input, use the following sequence:
<ESC>[!1;0z<ESC>[!2;0z
(HEX equivalent: 1B 5B 21 31 3B 30 7A 27 5B 21 32 3B 30 7A)
Dynamic Font Change
Where DoubleHigh and DoubleWide can each be either 0 or 1:
<ESC>[!5;<DoubleHigh>;<DoubleWide>;z
To set only Double High mode:
<ESC>[!5;1;0;z
To set only Double Wide mode:
6-22
Twin Client Reference
• June, 2005
Advanced Display Options for VT/HP
<ESC>[!5;0;1;z
To set Double High, Double Wide mode:
<ESC>[!5;1;1;z
To restore normal fonts:
<ESC>[!5;0;0;z
Advanced Display Options for VT/HP
The Advanced button in the advanced view Display tab is active when VT100, VT220,
or HP700 emulation is selected. This option group controls how display attributes are
processed, and it can also be used to simulate block mode operation (see the Mode option
description in the Chapter 5 section, Customizing the Keyboard).
Attribute Mask
This check box group enables (checked) or disables (unchecked) the display of the
indicated character attribute. The character-based terminal displays are capable of
displaying only the Reverse and Blinking attributes. All other attributes, if enabled, are
displayed in Reverse, except for those attributes checked in the Blink Mask group
(see below).
Field Mask
The VT100 and VT220 protocols do not support the more efficient block mode of
operation that is standard in the 3270 and 5250 protocols, since there are no VT100 or
VT220 protocol commands for defining input fields.
However, Twin Client makes it possible to simulate block mode operation by using video
display attributes to define input fields. Each box checked in the Field Mask window
indicates a video attribute that will be recognized as an input field specification by the
emulator. During a terminal session with a host, whenever the cursor is positioned on
character with the selected attribute(s), all characters to the right of that position with the
same attribute are interpreted to specify the length of the input field.
Blink Mask
This check box group is used to enable (checked) or disable (unchecked) the conversion
of the selected attribute to Blinking.
Twin Client Reference • June, 2005
6-23
Advanced Integration
Advanced 3270 Keyboard Options
The Advanced button in the advanced view Keyboard tab is active when 3270
emulation is selected. The option groups in this window are used to automate keystroke
generation under the special conditions described in the following subsections. It is also
used determine the action taken with oversized scans.
Attribute Key
This option is used to automatically transmit a keystroke to the 3270 host when the 3270
field matches the selected attribute. The automatic keystroke generation can be based on
whether the input is scanned, or keyed, or both.
Note: When this feature is made active (setting the Key to a value other than noop and
setting the Scan Field and or Key Field to a value other than off) it overrides all
other automatic keystroke generation rules except for the Last Field Keys rules
(described later in this section).
Key
This scrolling list box is used to select the 3270 keystroke sent with scanned or keyed
input when the field matches the selected attribute setting specified in Scan Field and
Key Field (described below). This option overrides all other automatic keystroke
generation, except for Last Field processing. The default key setting of noop disables this
function.
Scan Field
This scrolling list box selects the 3270 field attribute that, when data is scanned into the
field, results in automatic transmission of the selected Key with the data to the host. The
choices are pen (for 3270 Light Pen Enabled), num (for 3270 Numeric Only), hi
(for 3270 High Intensity) and hal (for 3270 High Intensity and Light Pen Enabled). The
default value is off.
Key Field
This scrolling list box selects the 3270 field attribute that, when data is keyed into the
field and the field is completely filled, results in automatic transmission of the selected
Key with the data to the host. The choices are pen (for 3270 Light Pen Enabled), num
6-24
Twin Client Reference
• June, 2005
Advanced 3270 Keyboard Options
(for 3270 Numeric Only), hi (for 3270 High Intensity) and hal (for 3270 High Intensity
and Light Pen Enabled). The default value is off.
Last Field Keys
This option is used to automate keystroke generation when the keyed or scanned input is
into the last field on the 3270 display.
Note: When this rule generates a keystroke, it overrides all other automatic keystroke
generation rules (i.e., Scan Key, Auto Send Key, and Attribute Key).
Scanned Input
This scrolling list box is used to select the 3270 keystroke to be sent when data is scanned
into the last field on the 3270 display. The default value is noop, which disables this
function.
Keyed Input
This scrolling list box is used to select the 3270 keystroke to be sent when data is keyed
into the last field on the 3270 display, and the field is filled. The default value is noop,
which disables this function.
Multiple Fields
This check box enables (checked) the Last Field Keys group only if the host display
contains more than one input field.
Key Wrap
This check box enables (checked) or disables (unchecked) the automatic wrapping of
oversized scanned input to subsequent 3270 input fields.
Note: This option has no effect if either Length Checking or Truncation options are
enabled (see Chapter 5, Customizing the Scanner).
Twin Client Reference • June, 2005
6-25
Advanced Integration
New Environ Telnet Extension
The New Environ Telnet extension, also known as Workstation ID, is a mechanism for
providing named variables with values to the host system via a Telnet negotiation at the
beginning of each terminal session.
The New Environ option under the Twin Client Manager's Settings menu is used to
create the variables, which are applied to all terminal configurations. Variables can be
created that apply only to specific terminals (indicated by IP address). It is also possible
to create variables that apply to all terminals.
Creating Common Settings
Variables that apply to all terminal sessions are created by clicking on the Common to
all terminals button, and then entering the Variable and Value in the respective boxes.
Then click on the Set button.
6-26
Twin Client Reference
• June, 2005
New Environ Telnet Extension
The variable and its value are then displayed in bottom list window.
Creating Terminal Specific Settings
Variables that apply to specific terminal sessions are created by clicking on the Terminal
Specific button, and entering the last two octets of the terminal IP address. Then enter
the Variable and Value in the respective boxes and click on the Set button.
Note: Click on the Show all settings check box to display both terminal specific and
common variables.
When you set up the IP address in the New Environment entry form, you can get an
“Invalid terminal address” error message. This error is from a routine that checks the IP
address for accuracy. In IP settings, it is possible to use octal notation rather than the
more common decimal method we see most often.
The rule is that if there is a leading zero, it assumes octal notation and checks for a valid
octal value (legal octal values are 0-7). For example if the second half of your terminal IP
address is 078.131, the 8 in the .078 is what causes the error. The terminal client needs
the leading zero(s) to correctly find the IP address. This leads to a catch 22.
Note: The following work-around will require that you hand edit the configuration file to
add the leading zeros if required.
1. Enter the address as normal without any leading zeros. If they are all 3-digit octets, you
need do nothing. If any octet is less than 3 digits, do the next step.
2. Open the PowerNet\TwinClient\tnenv.cf file for edit. Add leading zeros to entries:
78.132:DEVNAME=RF001;!
1.133:DEVNAME=RF002;!
12.134:DEVNAME=RF003;!
Twin Client Reference • June, 2005
→
→
→
078.132:DEVNAME=RF001;!
001.133:DEVNAME=RF002;!
012.134:DEVNAME=RF003;!
6-27
Advanced Integration
Save and send this to the terminal by doing a "Terminal/Send Configuration Files to
Terminal" operation.
Changing and Deleting Settings
Variable names and their values can be modified or deleted by clicking on the variable in
the list window. Change the variable or value by editing the Variable and/or Value
boxes, and click on the Set button. To delete the variable, press the Delete key on the PC.
Deleted variables will continue to appear in the pull down list until after the settings have
been saved.
Saving New Environ
Click on the OK button to save the New Environ settings.
TN3270E Negotiation
The following defines the TN3270E negotiation, permitting the transfer of some of the
TN3270E Sub-negotiation variables such as Lunames from the Telnet terminal to the
host during session initialization.
Note: This pertains to 3270 emulation.
TN3270E uses two text files located in the working directory (refer to
/etc/.CRF/WORKDIR). The tnenvcom.cf file allows for the definition of variables that
will be shared by all devices, and the tnenv.cf file allows for the definition of terminal-
specific variables. These files are currently created and maintained with the system
editor.
Line Entry Format, tnenvcom.cf:
VARIABLE=VALUE;
Example *DEVTYP=IBM-3278-2;*CONNECT=RFZ81;
This will assign all terminals the luname of RFZ81.
Line Entry format, tnenv.cf:
IDENT:VARIABLE=VALUE;[VARIABLE=VALUE]…!
Where IDENT is either the last two octets of the terminal's IP address, or the three digit
Spectrum address (065-511). Multiple variables can be defined, separated by semicolons. The entry is terminated with an exclamation.
Example file:
#IP terminals fully qualified octets 7 characters:
010.031:*DEVTYPE=IBM-3278-2;*CONNECT=RF3278.001;!
010.032:*DEVTYPE=IBM-3278-2;*CONNECT=RF3278.002;!
6-28
Twin Client Reference
• June, 2005
New Environ Telnet Extension
This will assign the terminal with an IP address of xxx.yyy.010.031 a device type of
IBM-3278-2 to the luname of RF3278.001.
New Environ Negotiation
The following defines the New Environ negotiation, permitting the transfer of
environmental variables from the Telnet terminal to the host during session initialization.
Note: This pertains to the 5250 and VT emulations.
New Environ uses two text files located in the working directory (refer to
/etc/.CRF/WORKDIR). The tnenvcom.cf file allows for the definition of variables that
will be shared by all devices, and the tnenv.cf file allows for the definition of terminalspecific variables. These files are currently created and maintained with the system
editor.
Line Entry Format, tnenvcom.cf:
VARIABLE=VALUE;
Line Entry format, tnenv.cf:
IDENT:VARIABLE=VALUE;[VARIABLE=VALUE]…!
Where IDENT is either the last two octets of the terminal's IP address, or the three digit
Spectrum address (065-511). Multiple variables can be defined, separated by semicolons. The entry is terminated with an exclamation.
Example file:
#IP terminals fully qualified octets 7 characters:
010.031:DEVNAME=RF5291.001;!
#Spectrum ONE fully qualified radio ID 3 characters
065:DEVNAME=RF5291.002;!
Twin Client Reference • June, 2005
6-29
Advanced Integration
This page is intentionally blank.
6-30
Twin Client Reference
• June, 2005
Chapter 7 • The Display Formatter
The display formatter adapts full screen Telnet applications to the portable terminal
environment without any modification to the host application. This powerful tool is
included with Twin Client.
A screen capture utility (included with the Twin Client Manager) is used to access the
host application via Telnet and "capture" the host displays. Once captured, the screens are
processed into a screen formatter object and assigned to a terminal configuration, which
can then be downloaded automatically to the terminal, over the wireless network.
The Twin Client Display Formatter provides the following unique features:
• Performance - Optimized for minimum run-time overhead and maximum speed.
• Transparency - Fully transparent to the host application.
• Capacity - Up to 128 host screens per object, 16 terminal screens per host screen,
and 32 input fields per terminal screen.
• Simplicity - Intuitive drag-and-drop interface for screen capture and formatting.
• Flexibility - Supports all Twin Client terminals.
This chapter describes how to set the emulation, capture the host application displays,
and process them into formatter objects for download to the terminal.
Setting the Emulation
The first step in the formatting process is to set the emulation in preparation for capturing
the host application displays. Click on Twin Client Manager under Start, Programs,
etc., and then the Settings menu, as shown below.
Click on Emulation and select an emulator from the list below.
Twin Client Reference
• June, 2005
7-1
The Display Formatter
Then click on OK to return to the main Twin Client menu.
Note: Display Formatting is available for the ANSI emulation only in Psion Teklogix
terminals.
Starting the Emulator
Start the emulator by clicking on the Object Editors menu and Screen Capture, as
shown below.
The emulation window is displayed. Click on the Session menu, and then click on
Session Settings.
7-2
Twin Client Reference
• June, 2005
Starting the Emulator
In the Session Settings menu, enter the Host IP address, port of the host system, and
select the appropriate emulation from the drop-down menu. Click on OK to return to the
emulator main menu.
Note: The Host Port of 23 is standard for Telnet. However, for security reasons the port
number may be set to other values. Consult the local network administrator if a
connection cannot be established on port 23.
Note: In vt emulation, this Twin Client screen has a scroll bar for selecting vt100, vt220,
or hp700 emulation.
To start a telnet session with the host, click on the
toolbar icon, or click on the
Session menu and then on Connect. In this example, the 5250 emulator is used and the
host system is an IBM AS/400.
The host application displays are now ready to be captured.
Twin Client Reference • June, 2005
7-3
The Display Formatter
Taking Snapshots
The host screens are captured by clicking on the
toolbar icon while the desired
screen is displayed. Alternately, click on Session and then Snapshot. The following
pop-up indicates that the screen was captured.
Click on OK and continue to navigate the host application, taking snapshots of the
screens to be formatted.
Saving the Screen File
Save the snapshots at any time by clicking on the
toolbar icon. Alternately, click on
File and then Save As. The following window is displayed for entering the filename.
For this example, the filename is set to Untitled. Then click on the Save button to return
to the emulator.
Exiting the Emulator
The telnet session is ended by clicking on the
toolbar icon, or by clicking on
Session and Disconnect. Return to the Twin Client Manager window to format the
screens by clicking on the icon at the top right corner of the emulator, or by clicking
on File and Exit.
7-4
Twin Client Reference
• June, 2005
Formatting
Formatting
The screen file created in the previous sections can now be formatted. This section
describes how to start the formatter, open a screen file, format the screens, save the
formatted object, and finally to assign it to a configuration.
Starting the Formatter
The formatter is started from the Twin Client Manager menu. Start the Twin Client
Manager by clicking on Twin Client Manager under Start, Programs, etc. Then click on
Object Editors, as shown below.
Click on the Display/Formatting option and the formatter window is displayed. To open
the screen file, click on File.
Then click on Open, and click on the screen filename.
Twin Client Reference • June, 2005
7-5
The Display Formatter
Then click on the Open button and the formatter window is displayed, including the first
host display that was captured. The terminal display window, which is blank at this time
since no formatting has taken place, is also shown.
Note: The Terminal display window floats on top of the host screen. If it needs to be
moved, click on the title bar and drag it to a different area of the host screen.
Setting Up the Formatter
The terminal display must be set to match the terminal for which the formatter object is to
be created. Click on the Tools menu and then Setup.
7-6
Twin Client Reference
• June, 2005
Formatting
Click on the desired terminal display size, and also ensure that the host screen size is set
correctly. Then click on OK to return to the formatter.
Note: If, while reformatting host screens, you are able to create display fields larger than
the selected screen size causing the reformatted screen not to appear on the
terminal; Delete the terminal screen in question and reformat it, paying attention to
the width of the RF terminal screen.
Copying an Input Field
An input field is copied from the host display to the terminal display by the same method
used to copy text. Click the left side of the input field and drag the cursor to the right. The
input field will be highlighted. Now click on the field again and drag it to the desired
position in the Terminal display.
Adding an Input Field
To add an input field, create text in the screen formatter window, highlight it, and choose
Add Input Field from the Host menu. The input field added in the example below is a
lower-case letter “x”.
Twin Client Reference • June, 2005
7-7
The Display Formatter
Adding and Copying Variable Display Text
Variable text can be added to the terminal display by clicking on the Terminal window,
moving the cursor to the desired display position, and typing in the text (in this case,
variable text) as shown below.
To do this, move the cursor to the desired position in the host display and hold down the
mouse button while moving the cursor to the right. Then, right-click on the text to be
copied. This text will be highlighted as shown by the words “variable text” copied
below. Then drag the highlighted text to the desired position in the terminal display and
release the mouse button.
7-8
Twin Client Reference
• June, 2005
Formatting
Deleting a Field
Select the text to be deleted by highlighting it, and choose Delete Field from the Host
menu.
Finding a Field on the Terminal
To find a field on the terminal, choose Find Field on Terminal from the Host menu.
Twin Client Reference • June, 2005
7-9
The Display Formatter
Adding an Ident
Formatting requires that each host screen to be uniquely identified. One way to do this is
to highlight unique text on the host screen (click on the left side of the text and drag the
mouse to the right). Then click on the right mouse button, as shown below.
From the pull down menu, click on Add Ident. The highlighted field is now colored red
on the host display, indicating that it is an Ident field. Up to 32 items can be highlighted
on each host screen, so if a number of screens share similar features, they can be uniquely
identified by adding more Idents. In the event that a group of host displays differ only by
position of input fields, input fields can be used for Idents also.
Removing an Ident
Remove an Ident field by highlighting it, and then selecting Remove Ident from the Host
menu.
7-10
Twin Client Reference
• June, 2005
Formatting
Navigating the Screen Formatter
To move to the first screen in the screen formatter, choose First Screen from the Host
menu.
To move to the next screen, select Next Screen from the Host menu.
Twin Client Reference • June, 2005
7-11
The Display Formatter
To move to the previous screen, select Previous Screen from the Host menu.
To move to the last screen, select Last Screen from the Host menu.
7-12
Twin Client Reference
• June, 2005
Formatting
Adding a Terminal Screen
New terminal screens are created by using the New button at the bottom of the Terminal
display window. This is useful when more that one terminal screen is required to format
the relevant data on the host screen. Up to 16 terminal displays can be associated with
each formatted host display. These are called terminal pages, and the page that is
displayed on the terminal at any point in time depends on the location of the host cursor
position. The page to which the corresponding input field is formatted is the one
displayed.
When multiple pages are present, the directional arrows are used to navigate through the
pages.
Deleting a Screen
To delete a screen, select Delete Screen from the Host menu.
Twin Client Reference • June, 2005
7-13
The Display Formatter
Saving the Formatter Object
The formatter object is saved by clicking on the
and Save.
toolbar icon, or by clicking on File
Assigning the Object to a Terminal Configuration
The formatter object is assigned to a terminal configuration by opening a terminal
configuration in the Twin Client Manager, assigning the object to the Display Formatting
Object, and saving the configuration.
To open a terminal configuration, click on File in the Twin Client Manager, as shown
below.
Then click on Open, and click on the desired terminal configuration.
7-14
Twin Client Reference
• June, 2005
Formatting
Then click on the advanced view Display tab, pull down the Display Formatter Object
scrolling list box, and click on the object.
Save the newly modified terminal configuration using the
toolbar icon, or click on
File and then Save. The new configuration, incorporating the formatter object, is updated
on the terminal, automatically, by booting the terminal.
Twin Client Reference • June, 2005
7-15
The Display Formatter
This page is intentionally blank.
7-16
Twin Client Reference
• June, 2005
Chapter 8 • Software Management
In addition to providing functions for the download of files to the terminal via the
traditional serial connection, the Twin Client Manager also provides for the management
of terminal software and configurations automatically, over the wireless network.
This chapter describes the automated capability in detail. Additional manual operations
involving serial download options are described at the end of this chapter.
Airloader Auto-Configuration
The Airloader Auto-Configuration form is accessed from the Twin Client Manager Tools
menu. Select Airloader.
Note: If no options are displayed, click on the Advanced<< button.
Enabling Automatic Downloads
Click to put a check in the box that allows terminals to be automatically configured via
RF to enable automatic downloading. In the event another PC on the network is already
configured and active, the following warning message is displayed.
Twin Client Reference
• June, 2005
8-1
Software Management
Synchronizing Configuration Files
Click to put a check in the Synchronize Configuration Files box to enable automatic
synchronization of configuration files on the terminal. When the terminal is booted, its
configuration files will be compared with the most recent on the PC. The terminal is
updated automatically if it does not have the latest revision.
Synchronizing Program Files
Click to put a check in the Synchronize Program Files box to enable automatic
synchronization of program files on the terminal. When the terminal is booted, its
program files will be compared with the most recent on the PC. The terminal is updated
automatically if it does not have the latest revision.
Automatic IP Address Assignment
New terminals will be assigned IP addresses automatically if the following box is
checked.
Note:
Do not check this option if a DHCP server is configured to manage address
assignments.
To set the addresses, click on the Addresses button to access the Segment Address
Assignments dialog box, as shown in the following figure.
8-2
Twin Client Reference
• June, 2005
Airloader Auto-Configuration
Enter the desired range in the From and To boxes as shown above, and click on Add.
Creating New Groups
Click on Terminal Group Manager, right click the mouse button, click on New Group.
Click on Browse, to find the appropriate configuration file. In the Auto-Group box,
check the item to be changed. Click on the pull-down menu for options.
Twin Client Reference • June, 2005
8-3
Software Management
Click on the Active check box after the configuration file and all of the other parameters
have been set.
8-4
Twin Client Reference
• June, 2005
Airloader Auto-Configuration
Clicking on the Thin Mode button will cause all terminals in this group that are currently
running in thick mode to be switched to thin mode the next time Airloader is run on the
terminal.
Click on the Schedule button to view a dialog box for scheduling an automatic Airloader
update.
Select the desired time and click on OK. Click on Update Now and the Airloader “push”
capability controls terminals from this end.
Twin Client Reference • June, 2005
8-5
Software Management
Setting the Segment
The Segment button restricts a terminal group to a range of IP addresses. The IP Address
can be any valid address on the segment as it is used only to identify the segment. The
setting of the Net Mask can be used to restrict the range. This feature is useful for
segregating terminal groups by location.
Setting Force Reload
The Force Reload button forces all terminals within a group to be automatically updated.
The following warning message appears.
Click on the Yes button to force the reload.
Setting the Default Terminal Group
New terminals that have not yet been assigned to any group are initially assigned to the
default group in effect when they are booted.
Any group can be made the default group by clicking on the group, and then clicking on
the right mouse button. Then click on the Make Default option.
Reassigning Terminals
After a terminal has been configured and assigned to the default group, it can be
reassigned to a new group by clicking on the terminal icon as shown below.
Then, holding the mouse button down, drag the terminal icon to the desired group as
shown next.
8-6
Twin Client Reference
• June, 2005
Mobile Device Manager (MDM) Features
Release the mouse button, which reassigns the terminal.
The next time the terminal is rebooted, it will be reconfigured as defined in the group
specification.
Mobile Device Manager (MDM) Features
Under Tools in Twin Client Manager are the Screen Watcher, Terminal Messenger, and
RF Monitor features.
Note: The terminal may or may not be able to utilize the Screen Watcher or Terminal
Messenger features depending on its authorization codes.
Select Screen Watcher, enter the terminal’s IP address, and click on OK.
A screen will appear with a display resembling the terminal screen.
Twin Client Reference • June, 2005
8-7
Software Management
Clicking on the Font button on the upper left brings up a screen in which you can modify
the font settings, as shown below.
Select Terminal Messenger from the Tools menu.
You may enter an Address Range in the From and To boxes on this screen. Click on Add
when finished.
Enter a message to send in the space provided, select the terminal to receive this message
by clicking on it in the Select Terminal(s) column, and click on the Send button to send
the message of your choice to the terminal of your choice.
See the example of the Terminal Messenger screen below.
8-8
Twin Client Reference
• June, 2005
Mobile Device Manager (MDM) Features
To remove a terminal from the list of terminals receiving your message, click on the
terminal number in the Select Terminal(s) column, and click on the Remove button.
Click on the appropriate button, Remove All, Select All, or Unselect All, to remove all
terminals, select all terminals, or unselect all terminals from the Select Terminal(s) list.
Note: Use the Ctrl and Shift keys to select multiple terminals.
Click on the Close button when finished.
Twin Client Reference • June, 2005
8-9
Software Management
Select RF Monitor from the Tools menu.
RF Monitor is an "Over The Air" diagnostic tool. It's used to collect diagnostic trace
information from RF terminals running PowerNet Twin Client software.
It runs on a Windows PC and will send a command to the RF terminal to start tracing.
The terminal, when it receives this command, will start sending the trace information
over the RF link to the PC that issued the command. This will be written to a file on this
PC that can be sent to us for analysis.
Click on File to Select Terminal or to Exit.
Choosing Select Terminal allows you to view a log of the terminal’s activity. Enter the
Terminal IP address and Terminal IP Port, and click on OK.
8-10
Twin Client Reference
• June, 2005
Mobile Device Manager (MDM) Features
Click on Edit. Select Find, and/or Find Next to search for pieces of information in your
log, or select Clear to clear the search.
Click on Actions to Start the Monitor or Stop the Monitor.
Click on Tools to set Debug Levels or Settings.
The options in Debug Levels are shown below.
Twin Client Reference • June, 2005
8-11
Software Management
The maximum log file size can be set under Settings.
Click on View to show or hide the Toolbar and the Status Bar.
This is the Toolbar. It is found near the top of the screen.
This is the Status Bar. It is found at the bottom of the screen.
Click on Help to bring up the following screen.
8-12
Twin Client Reference
• June, 2005
Mobile Device Manager (MDM) Features
RF Monitor is a very small program and does not even require installation. Just place it in
a directory on your PC and create a shortcut to run it. It will run on all versions of
Windows except V3.1 and Win 95.
1. Move RF MONITOR to a Win PC with Network access to the RF terminal.
2. Run RF MONITOR (create a shortcut or do a start/run).
3. From the pull down menu, select File/Select Terminal.
4. Key in the RF terminal IP address and leave the port at 1802.
5. From the pull down menu, select Tools/Select Debug level. Set all levels to 9
except Data stream and SNA.
Twin Client Reference • June, 2005
8-13
Software Management
6. With the RF terminal sitting at the Press Any Key prompt, select Actions/Start
Monitor.
7. Press a key on the RF terminal to open a session, and you should see trace data in the
RF Monitor window. When done, end the trace and the file will be named
tnxxx.yyy.log (where xxx.yyy is the last 2 octets of the RF terminal’s IP address) in
the directory in which RF Monitor was running.
8-14
Twin Client Reference
• June, 2005
Mobile Device Manager (MDM) Features
Common Problems with RF Monitor
•
The trace won’t start.
RF Monitor uses UDP to send commands to the RF Device. On busy networks UDP
packets are not always delivered. The terminal can miss the command to start the
trace. Below are some things that can be useful:
a. Ping the RF terminal from the same PC before starting RF Monitor (seems to
"open" a path to the terminal).
b. Start the monitor with the terminal at the Press Any Key prompt. (While the
terminal is at this prompt, it's not doing much and has a better chance of hearing
the start trace command.)
•
I don't understand what this trace means.
The trace that this tool collects is engineering level information. It allows an end user
to collect information that can be analyzed by Connect engineering.
It will generally be requested by Connect support to help diagnose a reported
problem.
To be able to read and understand these completely, you need to have an
understanding of:
Twin Client Reference • June, 2005
8-15
Software Management
a. Emulation protocols (IBM 5250, IBM 3270, DEC VT200, etc.)
b. PowerNet Twin Client products
c. RF Network concepts
d. Wired network concepts
e. Telnet sessions
f. TCP/IP
They are text files that can be read with any editor or viewer and can be useful to end
users and integrators even if they may not have all the requirements above.
•
I have an intermittent problem and it could happen on any one of my 100
terminals. RF Monitor only does one terminal at a time. What can I do?
RF Monitor is not the right diagnostic tool for this type of problem. PowerNet
products have another diagnostic tool that can be used called the "Diagnostic Server".
This tool can be set up to run trace diagnostics on up to 300 terminals at the same
time. This tool will be provided as needed for systems under PowerNet support
agreement OR by T&M when they are not covered.
It also includes the service of a PowerNet support engineer.
Server Transfer is another feature. From the Tools menu, select Server Transfer.
The FTP Settings screen appears.
To send object editor and configuration files from Windows to your Linux box, enter
your server address, and click on OK.
8-16
Twin Client Reference
• June, 2005
Manual Download of Configuration Files
Manual Download of Configuration Files
The automated configuration management provided by the Twin Client Manager
eliminates the need for manual terminal configuration. However, this function can be
accomplished manually by clicking on Terminal and Send Configuration Files to
Terminal. On the terminal, run ld.bat from the a:\ drive, but do not Enter at this time.
Note: This procedure assumes that the Twin Client was previously installed.
The following screen appears.
Now, choose Enter on the terminal, while choosing OK at the prompt above.
Boot the terminal.
The terminal is now ready to begin a Telnet session with the new configuration files.
Twin Client Reference • June, 2005
8-17
Software Management
This page is intentionally blank.
8-18
Twin Client Reference
• June, 2005
Chapter 9 • Keypad Configuration
7035 36-Key Diagrams
(7035 36-key diagrams begin on the next page.)
Twin Client Reference
• June, 2005
9-1
Keypad Configuration
F11 light
VT emulation
F12 dark F13 vol+
F1
F2
F3
page↓
page↑
S
H
I
F
T
blue
Off
E
NO
TN
E
R
▲
↑
◄
1
2
!
MNO
4
5
7
PQR
; ]
*
‘
6
\
Alt
YZ
8
esc
Ctrl
#
VWX
~
-_
3
/
@
:
GHI
>?
]
JKL
STU
→
↓
DEF
>
[
►
▼
←
ABC
<
^
F4
☼
orange
$
F14 vol-
9
space
0
(
)
clr
.
Tab
Del
|
F15
?
F5
,
F16
+
F6
-
F17
{
F7
F18
}
=
F8
“
`
%
F19
F9
&
M3
M5
M1
M4
M6
M2
F20
/
F10
orange b blue
shift+blue
shift+ctrl keytop shift+alt
alt+orange
shift
alt
9-2
Twin Client Reference
• June, 2005
7035 36-Key Diagrams
F11 light
3270 emulation
F12 dark F13 vol+
F1
F2
☼
orange
S
H
I
F
T
DEF
>
2
[
Off
E
NO
TN
E
R
4
5
7
*
9
F9
0
(
)
clr
delchar
,
F6
F17
{
dup
M3 M5
M1
reset
Del
X
`
Alt
YZ
.
F16
+
‘
6
\ inschar
space
|
% clear
F19 &
PQR
; ]
Tab
F5
Ctrl
#
8
esc
?
3
home
VWX
~
attn
GHI
>?
]
eof
MNO
:
►
→
@
fm
STU
F23
blue
↓
JKL
F15
F22
▼
←
! endpos
_
F21
↑
◄
1
^
F4
▲
ABC
<
$
F3
page↓
page↑
F14 vol-
F7
-
F18
}
=
F8
“
clr to fld
clr to end
M4 M6
F20
/
M2
F10
F24
help
pa1
orange blue
shift+blue
shift+ctrl keytop shift+alt
alt+orange
shift
alt
Twin Client Reference • June, 2005
9-3
Keypad Configuration
F11 light
5250 emulation
F12 dark F13 vol+
F1
F2
F3
page↓
page↑
☼
orange
S
H
I
F
T
F14 vol-
F4
F21
F22
blue
Off
E
NO
TN
E
R
▲
↑
◄
►
▼
←
→
↓
ABC
<
DEF
>
1
GHI
>?
2
[
! endpos
JKL
fldMNO
4
5
esc
F23
fldex
) reset
clr
Del
fld+
+
F9
0
.
,
F16
% clear
F19 &
home
YZ
(
space
|
?
F5
`
M3
dup
M5
M1
Alt
9
Tab
F15
:
* bottom
attn
‘
6
8
~
Ctrl
print
PQR
; ]
$
fm
VWX
\ in
7
_
#
@
STU
^
3
]
delchar
-
F17
{
F6
M4
F18
}
=
“
F7
clr to fld
clr to end
M6
F20
/
M2
F10
F24
help
top
orange blue
shift+blue
shift+ctrl keytop shift+alt
alt+orange
shift
alt
9-4
Twin Client Reference
• June, 2005
7035 36-Key Table
7035 36-Key Table
Key
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tab
Esc
Space
Shift
Ctrl
Alt
Enter
Off
VTERM
<Orange><1>
<Orange><1><1>
<Orange><1><1><1>
<Orange><2>
<Orange><2><2>
<Orange><2><2><2>
<Orange><3>
<Orange><3><3>
<Orange><3><3><3>
<Orange><4>
<Orange><4><4>
<Orange><4><4><4>
<Orange><5>
<Orange><5><5>
<Orange><5><5><5>
<Orange><6>
<Orange><6><6>
<Orange><6><6><6>
<Orange><7>
<Orange><7><7>
<Orange><7><7><7>
<Orange><8>
<Orange><8><8>
<Orange><8><8><8>
<Orange><9>
<Orange><9><9>
<Shift><Orange><1>
<Shift><Orange><1><1>
<Shift><Orange><1><1><1>
<Shift><Orange><2>
<Shift><Orange><2><2>
<Shift><Orange><2><2><2>
<Shift><Orange><3>
<Shift><Orange><3><3>
<Shift><Orange><3><3><3>
<Shift><Orange><4>
<Shift><Orange><4><4>
<Shift><Orange><4><4><4>
<Shift><Orange><5>
<Shift><Orange><5><5>
<Shift><Orange><5><5><5>
<Shift><Orange><6>
<Shift><Orange><6><6>
<Shift><Orange><6><6><6>
<Shift><Orange><7>
<Shift><Orange><7><7>
<Shift><Orange><7><7><7>
<Shift><Orange><8>
<Shift><Orange><8><8>
<Shift><Orange><8><8><8>
<Shift><Orange><9>
<Shift><Orange><9><9>
<Tab>
<Blue><Tab>
<Orange><.>
<Shift>
<Ctrl>
<Alt>
<Enter>
<Blue><Enter>
Twin Client Reference • June, 2005
3270
<Orange><1>
<Orange><1><1>
<Orange><1><1><1>
<Orange><2>
<Orange><2><2>
<Orange><2><2><2>
<Orange><3>
<Orange><3><3>
<Orange><3><3><3>
<Orange><4>
<Orange><4><4>
<Orange><4><4><4>
<Orange><5>
<Orange><5><5>
<Orange><5><5><5>
<Orange><6>
<Orange><6><6>
<Orange><6><6><6>
<Orange><7>
<Orange><7><7>
<Orange><7><7><7>
<Orange><8>
<Orange><8><8>
<Orange><8><8><8>
<Orange><9>
<Orange><9><9>
<Shift><Orange><1>
<Shift><Orange><1><1>
<Shift><Orange><1><1><1>
<Shift><Orange><2>
<Shift><Orange><2><2>
<Shift><Orange><2><2><2>
<Shift><Orange><3>
<Shift><Orange><3><3>
<Shift><Orange><3><3><3>
<Shift><Orange><4>
<Shift><Orange><4><4>
<Shift><Orange><4><4><4>
<Shift><Orange><5>
<Shift><Orange><5><5>
<Shift><Orange><5><5><5>
<Shift><Orange><6>
<Shift><Orange><6><6>
<Shift><Orange><6><6><6>
<Shift><Orange><7>
<Shift><Orange><7><7>
<Shift><Orange><7><7><7>
<Shift><Orange><8>
<Shift><Orange><8><8>
<Shift><Orange><8><8><8>
<Shift><Orange><9>
<Shift><Orange><9><9>
<Tab>
<Blue><Tab>
<Orange><.>
<Shift>
<Ctrl>
<Alt>
<Enter>
<Blue><Enter>
5250
<Orange><1>
<Orange><1><1>
<Orange><1><1><1>
<Orange><2>
<Orange><2><2>
<Orange><2><2><2>
<Orange><3>
<Orange><3><3>
<Orange><3><3><3>
<Orange><4>
<Orange><4><4>
<Orange><4><4><4>
<Orange><5>
<Orange><5><5>
<Orange><5><5><5>
<Orange><6>
<Orange><6><6>
<Orange><6><6><6>
<Orange><7>
<Orange><7><7>
<Orange><7><7><7>
<Orange><8>
<Orange><8><8>
<Orange><8><8><8>
<Orange><9>
<Orange><9><9>
<Shift><Orange><1>
<Shift><Orange><1><1>
<Shift><Orange><1><1><1>
<Shift><Orange><2>
<Shift><Orange><2><2>
<Shift><Orange><2><2><2>
<Shift><Orange><3>
<Shift><Orange><3><3>
<Shift><Orange><3><3><3>
<Shift><Orange><4>
<Shift><Orange><4><4>
<Shift><Orange><4><4><4>
<Shift><Orange><5>
<Shift><Orange><5><5>
<Shift><Orange><5><5><5>
<Shift><Orange><6>
<Shift><Orange><6><6>
<Shift><Orange><6><6><6>
<Shift><Orange><7>
<Shift><Orange><7><7>
<Shift><Orange><7><7><7>
<Shift><Orange><8>
<Shift><Orange><8><8>
<Shift><Orange><8><8><8>
<Shift><Orange><9>
<Shift><Orange><9><9>
<Tab>
<Blue><Tab>
<Orange><.>
<Shift>
<Ctrl>
<Alt>
<Enter>
<Blue><Enter>
9-5
Keypad Configuration
Backspace
Light
Dark
Vol+
Vol1
2
3
4
5
6
7
8
9
0
!
exclamation
@
at sign
# pound, number, hash
$
dollar
:
colon
\
backward slash
_
underscore
*
asterisk
(
left parenthesis
)
right parenthesis
,
comma
.
period
hyphen
&
ampersand
/
forward slash
`
grave accent
=
equal sign
^
carat
%
percent
[
left bracket
]
right bracket
;
semicolon
‘
apostrophe
~
tilde
+
addition sign
{
left brace
}
right brace
|
vertical bar
“
quotation
<
less than
>
greater than
?
question mark
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
9-6
<Del>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<1>
<2>
<3>
<4>
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<Blue><F6>
<.>
<Blue><F7>
<Blue><F9>
<Blue><F10>
<Shift><F6>
<Blue><F8>
<Shift><Ctrl><7>
<Shift><F5>
<Shift><Alt><1>
<Shift><Ctrl><6>
<Shift><Alt><5>
<Shift><Alt><6>
<Shift><Alt><7>
<Shift><Alt><F5>
<Shift><Alt><F6>
<Shift><Alt><F7>
<Alt><Tab>
<Shift><Alt><F8>
<Shift><Blue><1>
<Shift><Blue><3>
<Blue><F5>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<Orange><F1>
<Orange><F2>
<Orange><F3>
<Orange><F4>
<Orange><F5>
<Orange><F6>
<Orange><F7>
<Orange><F8>
<Orange><F9>
<Del>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<1>
<2>
<3>
<4>
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<Blue><F6>
<.>
<Blue><F7>
<Blue><F9>
<Blue><F10>
<Shift><F6>
<Blue><F8>
<Shift><Ctrl><7>
<Shift><F5>
<Shift><Alt><1>
<Shift><Ctrl><6>
<Shift><Alt><5>
<Shift><Alt><6>
<Shift><Alt><7>
<Shift><Alt><F5>
<Shift><Alt><F6>
<Shift><Alt><F7>
<Alt><Tab>
<Shift><Alt><F8>
<Shift><Blue><1>
<Shift><Blue><3>
<Blue><F5>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<Orange><F1>
<Orange><F2>
<Orange><F3>
<Orange><F4>
<Orange><F5>
<Orange><F6>
<Orange><F7>
<Orange><F8>
<Orange><F9>
<Del>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<1>
<2>
<3>
<4>
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<Blue><F6>
<.>
<Blue><F7>
<Blue><F9>
<Blue><F10>
<Shift><F6>
<Blue><F8>
<Shift><Ctrl><7>
<Shift><F5>
<Shift><Alt><1>
<Shift><Ctrl><6>
<Shift><Alt><5>
<Shift><Alt><6>
<Shift><Alt><7>
<Shift><Alt><F5>
<Shift><Alt><F6>
<Shift><Alt><F7>
<Alt><Tab>
<Shift><Alt><F8>
<Shift><Blue><1>
<Shift><Blue><3>
<Blue><F5>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<Orange><F1>
<Orange><F2>
<Orange><F3>
<Orange><F4>
<Orange><F5>
<Orange><F6>
<Orange><F7>
<Orange><F8>
<Orange><F9>
Twin Client Reference
• June, 2005
7035 36-Key Table
F20
F21
F22
F23
F24
M1
M2
M3
M4
M5
M6
▲ (Up)
▼ (Down)
◄ (Left)
► (Right)
↑ (View up)
↓ (View down)
← (View left)
→ (View right)
Page up
Page down
Inschar
Delchar
Home
Roll up
Roll down
PA1
PA2
PA3
Attention
Bottom
Clear
Field exit
FM
Help
EOF
Field Field +
Reset
Sys req
Top
Dup
Print
EndPos
Clear field
Clear to end
<Orange><F10>
--------<M1>
<M2>
<Orange><M1>
<Orange><M2>
<Blue><M1>
<Blue><M2>
<▲>
<▼>
<◄>
<►>
<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<Alt><Orange><F1>
<Alt><Orange><F2>
---------------------------------------------------
Twin Client Reference • June, 2005
<Orange><F10>
<Shift><F3>
<Shift><F4>
<Shift><F9>
<Shift><F10>
<M1>
<M2>
<Orange><M1>
<Orange><M2>
<Blue><M1>
<Blue><M2>
<▲>
<▼>
<◄>
<►>
<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
----<Alt><6>
<Alt><Del>
<Alt><5>
----<Alt><F10>
<Alt><F11>
<Alt><F12>
<Alt><7>
--<Alt><F5>
--<Alt><4>
<Alt><F9>
<Alt><2>
----<Alt><0>
<Alt><,>
--<Alt><F6>
--<Alt><1>
<Alt><F7>
<Alt><F8>
<Orange><F10>
<Shift><F3>
<Shift><F4>
<Shift><F9>
<Shift><F10>
<M1>
<M2>
<Orange><M1>
<Orange><M2>
<Blue><M1>
<Blue><M2>
<▲>
<▼>
<◄>
<►>
<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
----<Alt><6>
<Alt><Del>
<Alt><5>
<Alt><U>
<Alt><D>
------<Alt><7>
<Alt><8>
<Alt><F5>
<Alt><9>
<Alt><4>
<Alt><F9>
--<Alt><2>
<Alt><.>
<Alt><0>
<Alt><,>
<Alt><F10>
<Alt><F6>
<Alt><3>
<Alt><1>
<Alt><F7>
<Alt><F8>
9-7
Keypad Configuration
7035 44-Key Diagrams
(7035 44-key diagrams begin on the next page.)
9-8
Twin Client Reference
• June, 2005
7035 44-Key Diagrams
F17 light
F13F1 “
VT emulation
F18 dark
F19 vol+
F14 F2 F18
F20 vol-
F15 F3F17
F19
F16 F4F18
F20
☼
orange
blue
Off
Enter / On
Ctrl
↑
▲
Esc
←
Shift
↓
▼
◄
clr
Alt
A
Del
|
←
x
→
C
→
►
B
<
-
D
Space
E
7 -
8 *
F
9 (
G
H
4 $
5 :
6 \
]
I
J
K
1 !
2
3 #
@
;
L
M
.
O
F5
F5 F19
‘
S F9
F9
}
W M1 /
M1
N “
,
0 )
P
F6
F6 F20
T
F10
F10
~
>
X M2 `
M2
Q
U
Y
F7
F7 pg↑
+
F11
F11
?
M3=
M3
R
F8
F8 pg↓
{
V F12
F12
Z
[
M4
orange alt blue
ctrl keytop shift
shift+ctrl
Twin Client Reference • June, 2005
9-9
Keypad Configuration
F17 light
F13F1 “
3270 emulation
F18 dark
F14 F2 F18
F15 F3F17F
F16F4F18 F20
blue
Off
Enter / On
Ctrl
◄
delchar clr
Del
A
-
7 -
Space
bot
E fld x
8 *
9 (
G home
5 :
H inschar
6 \
J
K print
3 #
I endpos
1 !
L fld+
►
B <
D
4 $
→
|
←
x
→
attn
fm
Shift
rl↓ ↓
▼
←
.
Alt
rl↑ ↑
▲
Esc
F
F20 vol-
☼
orange
C
F19 vol+
]
eof
2
@
F21
;
M reset
N
0 )
F22
F24
W M1
M1
/
>
R clrtoend
F8 pg↓
V
{
pa3
F12
?
X M2
M2
`
,
F23
Q clrfld
O clearF5 P dup
F8 F5 F19
F6 F20
F7 pg↑
‘
~
+
S help F T pa1
U pa2
F9
F10
F11
}
sreq
Y
M3
M3
=
Z
M4
M4
[
orange alt blue
ctrl keytop shift
alt+orange
shift+ctrl
9-10
Twin Client Reference
• June, 2005
7035 44-Key Table
F17 light
5250 emulation
F13F1 “
F18 dark
F14 F2 F18
F16 F4 F18
blue
Off
Enter / On
Ctrl
Alt
↑
▲
Esc
◄
delchar clr
Del
A
B <
-
7 fm
4 $
I endpos
1 !
L fld+
.
F22
O clearF5
F8 F5 F19
→
►
|
←
x
→
D
attn
Shift
rl↓ ↓
▼
←
F
F15F3F17 F
F20 vol-
☼
orange
C
F19 vol+
E fld x
bot
8 *
9 (
G home
5 :
H inschar
6 \
J
K print
3 #
]
fld-
2
@
F21
;
M reset
0 )
N sreq
,
F24
F23
‘
S help F
F9
P dup
Q clrfld
F6 F20
F7 pg↑
~
+
T top0
U F11
F10
F11
}
W M1
M1
>
X M2
M2
/
Space
`
Y
?
M3
M3
=
R clrtoend
F8 pg↓
{
V F12
F12
Z
M4
M4
[
orange alt blue
ctrl keytop shift
alt+orange
shift+ctrl
Twin Client Reference • June, 2005
9-11
Keypad Configuration
7035 44-Key Table
Key
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tab/Backtab
Esc
Space
Shift
Ctrl
Alt
Enter
Del
1
2
9-12
VTERM
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Tab/Backtab>
<Esc>
<Space>
<Shift>
<Ctrl>
<Alt>
<Enter>
<Del>
<1>
<2>
3270
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Tab/Backtab>
<Esc>
<Space>
<Shift>
<Ctrl>
<Alt>
<Enter>
<Del>
<1>
<2>
5250
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Tab/Backtab>
<Esc>
<Space>
<Shift>
<Ctrl>
<Alt>
<Enter>
<Del>
<1>
<2>
Twin Client Reference
• June, 2005
7035 44-Key Table
3
4
5
6
7
8
9
0
!
exclamation
@
at sign
# pound, number, hash
$
dollar
:
colon
\
backward slash
_
underscore
*
asterisk
(
left parenthesis
)
right parenthesis
/
forward slash
`
grave accent
=
equal sign
[
left bracket
]
right bracket
;
semicolon
‘
apostrophe
~
tilde
+
addition sign
{
left brace
}
right brace
|
vertical bar
“
quotation
<
less than sign
>
greater than sign
?
question mark
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
M1
M2
M3
M4
▲ (Up)
▼ (Down)
◄ (Left)
► (Right)
<3>
<4>
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<Blue><M1>
<Blue><M2>
<Blue><M3>
<Blue><M4>
<Shift><Ctrl><6>
<Shift><Ctrl><2>
<Shift><Ctrl><F5>
<Shift><Ctrl><F6>
<Shift><Ctrl><F7>
<Shift><Ctrl><F8>
<Shift><Ctrl><F9>
<Alt><Tab>
<Alt><Orange><c>
<Alt><->
<Shift><Ctrl><F10>
<Shift><Ctrl><F11>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<F11>
<F12>
<Ctrl><F1>
<Ctrl><F2>
<Ctrl><F3>
<Ctrl><F4>
<Shift><F3>
<Shift><F4>
<Shift><F5>
<Shift><F6>
--------<M1>
<M2>
<M3>
<M4>
<▲>
<▼>
<◄>
<►>
Twin Client Reference • June, 2005
<3>
<4>
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<Blue><M1>
<Blue><M2>
<Blue><M3>
<Blue><M4>
<Shift><Ctrl><6>
<Shift><Ctrl><2>
<Shift><Ctrl><F5>
<Shift><Ctrl><F6>
<Shift><Ctrl><F7>
<Shift><Ctrl><F8>
<Shift><Ctrl><F9>
<Alt><Tab>
<Alt><Orange><c>
<Alt><->
<Shift><Ctrl><F10>
<Shift><Ctrl><F11>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<F11>
<F12>
<Ctrl><F1>
<Ctrl><F2>
<Ctrl><F3>
<Ctrl><F4>
<Shift><F3>
<Shift><F4>
<Shift><F5>
<Shift><F6>
<Alt><Orange><3>
<Alt><Orange><.>
<Alt><Orange><,>
<Alt><Orange><0>
<M1>
<M2>
<M3>
<M4>
<▲>
<▼>
<◄>
<►>
<3>
<4>
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<Blue><M1>
<Blue><M2>
<Blue><M3>
<Blue><M4>
<Shift><Ctrl><6>
<Shift><Ctrl><2>
<Shift><Ctrl><F5>
<Shift><Ctrl><F6>
<Shift><Ctrl><F7>
<Shift><Ctrl><F8>
<Shift><Ctrl><F9>
<Alt><Tab>
<Alt><Orange><c>
<Alt><->
<Shift><Ctrl><F10>
<Shift><Ctrl><F11>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<F11>
<F12>
<Ctrl><F1>
<Ctrl><F2>
<Ctrl><F3>
<Ctrl><F4>
<Shift><F3>
<Shift><F4>
<Shift><F5>
<Shift><F6>
<Alt><Orange><3>
<Alt><Orange><.>
<Alt><Orange><,>
<Alt><Orange><0>
<M1>
<M2>
<M3>
<M4>
<▲>
<▼>
<◄>
<►>
9-13
Keypad Configuration
↑ (View up)
↓ (View down)
← (View left)
→ (View right)
,
.
Inschar
Delchar
Home
Roll up
Roll down
PA1
PA2
PA3
Attention
Bottom
Clear
Field exit
FM
Help
EOF
Field Field +
Reset
Sys req
Top
Dup
Print
EndPos
Clear field
Clear to end
Page up
Page down
Lighten
Darken
Vol+
Vol-
9-14
comma
period
hyphen
<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<,>
<.>
<->
------------------------------------------------------<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<,>
<.>
<->
<Alt><6>
<Alt><Del>
<Alt><5>
----<Alt><F10>
<Alt><F11>
<Alt><F12>
<Alt><7>
--<Alt><F5>
--<Alt><4>
<Alt><F9>
<Alt><2>
----<Alt><0>
<Alt><,>
--<Alt><F6>
--<Alt><1>
<Alt><F7>
<Alt><F8>
<Shift><F7>
<Shift><F8>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<,>
<.>
<->
<Alt><6>
<Alt><Del>
<Alt><5>
<Alt><Orange><U>
<Alt><Orange><D>
------<Alt><7>
<Alt><8>
<Alt><F5>
<Alt><9>
<Alt><4>
<Alt><F9>
--<Alt><2>
<Alt><.>
<Alt><0>
<Alt><,>
<Alt><F10>
<Alt><F6>
<Alt><3>
<Alt><1>
<Alt><F7>
<Alt><F8>
<Shift><F7>
<Shift><F8>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
Twin Client Reference
• June, 2005
7035 56-Key Diagrams
7035 56-Key Diagrams
(7035 56-key diagrams begin on the next page.)
Twin Client Reference • June, 2005
9-15
Keypad Configuration
light
F1
VT emulation
dark
F2
vol+
F3
volF4
☼
orange
Ctrl
Esc
orange shift blue
keytop
alt
blue
Alt
◄
▲
↑
►
←
▼
→
Shift
↓
clr
<
_
Del
*
>
8
7
^
$
[
←
→
:
]
4
/
.
)
1
off
9
E
N O
T N
E
R
6
@
}
(
\
-
5
!
{
+
=
2
#
?
3
SP
)
I
F5 %
A
“
B
F9
E
home
M6
9-16
G
J
F16
L
F19 pgdn
F20
M
N
O
P
F21 M2
F22 M3
F23 M4
F24 M5
R
S
F8
H
K
F18 ins
D
F12
F15 pgup
F14
F17
‘
F7
C
F11 ,
F10 &
F13
end
Q
~
`
)
0
F
I
M1
;
F6
T
F25
U
F26 M7 F27 M8
F28 M9
F29 M10
F30
V
W
X
Y
Z
Twin Client Reference
• June, 2005
7035 56-Key Diagrams
light
F1
3270 emulation
dark
F2
volF4
☼
orange
Ctrl
Esc
rl↓
vol+
F3
orange shift blue
keytop
alt
blue
Alt
◄
▲
↑
►
←
▼
→
rl↑
Shift
↓
clr
<
Del
delchar
^
[
.
(
off
E
N O
T N
E
R
7
8
9
bottom
fld ex
:
]
\
-
4
5
6
fm
home
inschar
#
!
{
@
)
}
1
=
2
?
3
eof
endpos
fld+
+
attn
$
←
→
/
> *
_
SP
print
)
I
F5 %
A
clr
B
dup
“
F9
E
help
home
M6
G
pa2
F17
K
F12
F16
L
F21
F22
F19 pgdn
F18 ins
F20
F24
N
F23
O
P
F21 M2
F22 M3
F23 M4
F24 M5
R
S
F8
H
pa3
pgup
F15pgup
F14
D
clrtoend
F11 ,
F10 &
J
M
Q
~
‘
F7
C
clrfld
reset
F13
end
`
)
0
F
pa1
I
M1
;
F6
T
F25
U
F26 M7 F27 M8
F28 M9
F29 M10
F30
V
W
X
Y
Z
Twin Client Reference • June, 2005
9-17
Keypad Configuration
light
F1
5250 emulation
dark
F2
vol+
F3
volF4
☼
orange
Ctrl
Esc
orange shift blue
keytop
alt
blue
Alt
◄
▲
↑
►
←
▼
→
Shift
↓
clr
<
_
^
[
.
off
E
N O
T N
E
R
9
attn
$
bottom
fld ex
:
]
\
-
4
5
6
fm
home
inschar
#
!
{
@
)
}
1
fld+
(
8
←
→
/
+
7
Del
delchar
*
>
=
2
endpos
?
3
fld-
SP
print
)
I
F5 %
A
clr
B
dup
“
F9
E
home
M6
9-18
G
F17
F16
L
F21
F22
F19 pgdn
F20
F24
F23
N
O
P
F21 M2
F22 M3
F23 M4
F24 M5
R
S
F8
H
K
F18 ins
D
rl↓
F12
pgup
F15pgup
F14
J
M
F11 ,
F10 &
F13
end
Q
~
‘
F7
C
clrfld
reset
top
I
`
)
0
F
help
M1
;
F6
T
F25
U
rl↑
F26 M7 F27 M8
F28 M9
F29 M10
F30
V
W
X
Y
Z
Twin Client Reference
• June, 2005
7035 56-Key Table
7035 56-Key Table
Key
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tab/Backtab
Esc
Space
Shift
Ctrl
Alt
Enter
Del
VTERM
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Tab/Bktab>
<Esc>
<Sp>
<Shift>
<Ctrl>
<Alt>
<Enter>
<Del>
Twin Client Reference • June, 2005
3270
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Tab/Bktab>
<Esc>
<Sp>
<Shift>
<Ctrl>
<Alt>
<Enter>
<Del>
5250
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Tab/Bktab>
<Esc>
<Sp>
<Shift>
<Ctrl>
<Alt>
<Enter>
<Del>
9-19
Keypad Configuration
1
2
3
4
5
6
7
8
9
0
!
exclamation
@
at sign
# pound, number, hash
$
dollar
%
percent
^
carat
&
ampersand
*
asterisk
(
left parenthesis
)
right parenthesis
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
M1
M2
M3
M4
M5
M6
M7
M8
M9
M10
▲ (Up)
▼ (Down)
◄ (Left)
► (Right)
↑ (View up)
↓ (View down)
← (View left)
→ (View right)
/
forward slash
`
accent
hyphen
=
equal sign
9-20
<1>
<2>
<3>
<4>
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Orange><b>
<Orange><Tab/Bktab>
<Orange><g>
<Shift><8>
<Shift><9>
<Shift><0>
<F1>
<F2>
<F3>
<F4>
<Blue><a>
<Blue><b>
<Blue><c>
<Blue><d>
<Blue><e>
<Blue><f>
<Blue><g>
<Blue><h>
<Blue><i>
<Blue><j>
<Blue><k>
<Blue><l>
<Blue><m>
<Blue><n>
<Blue><o>
<Blue><p>
--------<Orange><q>
<Orange><r>
<Orange><s>
<Orange><t>
<Orange><u>
<Orange><v>
<Orange><w>
<Orange><x>
<Orange><y>
<Orange><z>
<▲>
<▼>
<◄>
<►>
<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<Orange><.>
<Orange><c>
<Orange><6>
<Orange><3>
<1>
<2>
<3>
<4>
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Orange><b>
<Orange><Tab/Bktab>
<Orange><g>
<Shift><8>
<Shift><9>
<Shift><0>
<F1>
<F2>
<F3>
<F4>
<Blue><a>
<Blue><b>
<Blue><c>
<Blue><d>
<Blue><e>
<Blue><f>
<Blue><g>
<Blue><h>
<Blue><i>
<Blue><j>
<Blue><k>
<Blue><l>
<Blue><m>
<Blue><n>
<Blue><o>
<Blue><p>
<Alt><k>
<Alt><l>
<Alt><n>
<Alt><m>
<Orange><q>
<Orange><r>
<Orange><s>
<Orange><t>
<Orange><u>
<Orange><v>
<Orange><w>
<Orange><x>
<Orange><y>
<Orange><z>
<▲>
<▼>
<◄>
<►>
<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<Orange><.>
<Orange><c>
<Orange><6>
<Orange><3>
<1>
<2>
<3>
<4>
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Orange><b>
<Orange><Tab/Bktab>
<Orange><g>
<Shift><8>
<Shift><9>
<Shift><0>
<F1>
<F2>
<F3>
<F4>
<Blue><a>
<Blue><b>
<Blue><c>
<Blue><d>
<Blue><e>
<Blue><f>
<Blue><g>
<Blue><h>
<Blue><i>
<Blue><j>
<Blue><k>
<Blue><l>
<Blue><m>
<Blue><n>
<Blue><o>
<Blue><p>
<Alt><k>
<Alt><l>
<Alt><n>
<Alt><m>
<Orange><q>
<Orange><r>
<Orange><s>
<Orange><t>
<Orange><u>
<Orange><v>
<Orange><w>
<Orange><x>
<Orange><y>
<Orange><z>
<▲>
<▼>
<◄>
<►>
<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<Orange><.>
<Orange><c>
<Orange><6>
<Orange><3>
Twin Client Reference
• June, 2005
7035 56-Key Table
[
left bracket
]
right bracket
\
backward slash
;
semicolon
‘
apostrophe
,
comma
.
period
~
tilde
_
underscore
+
addition sign
{
left brace
}
right brace
|
broken vertical bar
:
colon
“
quotation mark
<
less-than sign
>
greater-than sign
?
question mark
Inschar
Home
Endpos
Page Up
Page Down
Roll up
Roll down
PA1
PA2
PA3
Attention
Bottom
Clear
Field exit
FM
Help
EOF
Field Field +
Reset
Sys req
Top
Dup
Print
Delchar
Clear field
Clear to end
Lighten
Darken
Vol+
Vol-
<Orange><4>
<Orange><5>
<Shift><6>
<Orange><0>
<Orange><d>
<Orange><h>
<.>
<Orange><f>
<Shift><7>
<Orange><9>
<Orange><1>
<Orange><2>
<Orange><a>
<Shift><5>
<Orange><e>
<Orange><7>
<Orange><8>
<Orange><Sp>
------<Orange><l>
<Orange><p>
--------------------------------------------<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
Twin Client Reference • June, 2005
<Orange><4>
<Orange><5>
<Shift><6>
<Orange><0>
<Orange><d>
<Orange><h>
<.>
<Orange><f>
<Shift><7>
<Orange><9>
<Orange><1>
<Orange><2>
<Orange><a>
<Shift><5>
<Orange><e>
<Orange><7>
<Orange><8>
<Orange><Sp>
<Orange><o>
<Orange><i>
<Orange><m>
--------<Alt><F10>
<Alt><F11>
<Alt><F12>
<Alt><7>
--<Alt><F5>
--<Alt><4>
<Alt><F9>
<Alt><2>
----<Alt><0>
<Alt><,>
--<Alt><F6>
--<Alt><Del>
<Alt><F7>
<Alt><F8>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<Orange><4>
<Orange><5>
<Shift><6>
<Orange><0>
<Orange><d>
<Orange><h>
<.>
<Orange><f>
<Shift><7>
<Orange><9>
<Orange><1>
<Orange><2>
<Orange><a>
<Shift><5>
<Orange><e>
<Orange><7>
<Orange><8>
<Orange><Sp>
<Orange><o>
<Orange><i>
<Orange><m>
----<Alt><U>
<Alt><D>
------<Alt><7>
<Alt><8>
<Alt><F5>
<Alt><9>
<Alt><4>
<Alt><F9>
--<Alt><2>
<Alt><.>
<Alt><0>
<Alt><,>
<Alt><F10>
<Alt><F6>
<Alt><3>
<Alt><Del>
<Alt><F7>
<Alt><F8>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
9-21
Keypad Configuration
8255/8260 QWERTY Diagrams
(8255/8260 diagrams begin on the next page.)
9-22
Twin Client Reference
• June, 2005
8255/8260 QWERTY Diagrams
VT emulation
F11 F21 F12 F22
F1
F2
M1 “
~
q
Q
`
w
‘
a
e
s
X
M4 &
f
F
vol+
c
C
M5 %
T
home
v
V
M6
Y
pgup
b
B
|
M7
U
pgdn
M9
O
tab
.
orange
p
Del
>
blue
▲
↑
4
$
{
(
-
5
6
:
\
=
}
2
1
3
#
@
►
→ ;
▼
↓
9
*
}
!
◄
←
+
8
7
_
{
P
L
clr
M
<
M10
l
Space
orange
F10
o
k
K
shift
m
,
i
I
end
J
alt
F9
bklite
/ M8
j
n
N
F8
u
h
H
ctrl
F18 F28 F19 F29 F20 F30
F7
y
g
G
vol- esc
F17 F27
F6
t
R
D
cntrst-
F5
r
d
x
z
M3 ^
E
F15 F25 F16 F26
F4
M12
S
cntrst+
Z
F3
M2 ?
W
M11
A
F13 F23 F14 F24
0
Enter
)
blue
keytop
shift
Twin Client Reference • June, 2005
alt
9-23
Keypad Configuration
3270 emulation
F11 F21 F12 F22
F1
F13 F23 F14 F24
F2
F3
F15 F25 F16 F26
F4
F5
F6
clr
M1 “
~
q
Q
`
M2 ?
w
W
M11
‘
a
A
Z
e
E
M4 &
T
home
s
S
d
D
cntrst-
x
X
f
roll↓ F
vol+
c
C
v
V
Y
pgup
F8
H
ctrl
/
M8
F9
j
J
alt
M9
F10
p
O
tab
◄
Del
dlchr
orange
>
blue
attn *
▼
↓
4
9
(
-
}
5
6
fm :
}
$
{
!
;
@
3
eof #
Enter
0
)
\
=
2
1
►→
←
+
8
7
_
{
▲
↑
L
M
orange
P
l
Space
<
pa1
M10
.
o
k
K
shift
m
,
i
U roll↑ I
pgdn
end
n
N
M7
u
h
b
B
|
y
g
G
vol- esc
F7
M6
t
R
F18 F28 F19 F29 F20 F30
dup sreq clrfld bklite clrtnd ins help
M5 %
r
M12
cntrst+
z
M3 ^
F17 F27
reset
blue
keytop
shift
9-24
alt
Twin Client Reference
• June, 2005
8255/8260 QWERTY Diagrams
5250 emulation
F11 F21 F12 F22
F1
F13 F23 F14 F24
F2
F3
F15 F25 F16 F26
F4
F5
F6
clr
M1 “
~
q
Q
`
w
W
M11
‘
a
A
E
s
R
D
f
c
C
v
V
Y
pgup
F8
H
ctrl
M7
F9
M8
roll↑ I
end
U
pgdn
j
n
,
M9
i
J
alt
N
/
u
h
b
B
|
y
g
roll↓ F
G
vol+
vol- esc
F7
M6
t
T
home
F18 F28 F19 F29 F20 F30
dup sreq clrfld bklite clrtnd ins help
M5 %
r
d
x
X
M4 &
M12
cntrst-
z
M3 ^
e
S
cntrst+
Z
M2 ?
F17 F27
m
.
o
▲
↑
◄
Del
M
dlchr
orange
attn *
}
4
fm
$
{
:
1
0
)
6
\
=
2
@
3
fld- #
Enter
reset
blue
keytop
shift
Twin Client Reference • June, 2005
fldx
bot (
-
}
!
▼
↓
9
5
►
→ ;
←
+
8
7
blue
P
L
clr
>
_
{
M10
l
Space
orange
top
p
O
tab
k
K
shift
F10
<
alt
9-25
print
Keypad Configuration
8255/8260 QWERTY Table
Key
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Del
Enter
Space
1
2
3
4
9-26
VTERM
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Del>
<Enter>
<Space>
<1>
<2>
<3>
<4>
3270
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Del>
<Enter>
<Space>
<1>
<2>
<3>
<4>
5250
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Del>
<Enter>
<Space>
<1>
<2>
<3>
<4>
Twin Client Reference
• June, 2005
8255/8260 QWERTY Table
5
6
7
8
9
0
!
exclamation
@ at sign
# pound
$ dollar
:
colon
\
backward slash
_ underscore
*
asterisk
(
left parenthesis
)
right parenthesis
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
M1
M2
M3
M4
M5
M6
M7
M8
M9
M10
M11
M12
▲
◄
▼
►
{ left brace
} right brace
= equal sign
[ left bracket
] right bracket
- hyphen
< less-than sign
> greater-than sign
+ addition sign
; semicolon
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<Orange><F1>
<Orange><F2>
<Orange><F3>
<Orange><F4>
<Orange><F5>
<Orange><F6>
<Orange><F7>
<Orange><F8>
<Orange><F9>
<Orange><F10>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<Blue><q>
<Blue><w>
<Blue><e>
<Blue><r>
<Blue><t>
<Blue><y>
<Blue><u>
<Blue><i>
<Blue><o>
<Blue><p>
<Blue><a>
<Blue><s>
<▲>
<◄>
<▼>
<►>
<Orange><1>
<Orange><2>
<Orange><3>
<Orange><4>
<Orange><5>
<Orange><6>
<Orange><7>
<Orange><8>
<Orange><9>
<Orange><0>
Twin Client Reference • June, 2005
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<Orange><F1>
<Orange><F2>
<Orange><F3>
<Orange><F4>
<Orange><F5>
<Orange><F6>
<Orange><F7>
<Orange><F8>
<Orange><F9>
<Orange><F10>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<Blue><q>
<Blue><w>
<Blue><e>
<Blue><r>
<Blue><t>
<Blue><y>
<Blue><u>
<Blue><i>
<Blue><o>
<Blue><p>
<Blue><a>
<Blue><s>
<▲>
<◄>
<▼>
<►>
<Orange><1>
<Orange><2>
<Orange><3>
<Orange><4>
<Orange><5>
<Orange><6>
<Orange><7>
<Orange><8>
<Orange><9>
<Orange><0>
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<Orange><F1>
<Orange><F2>
<Orange><F3>
<Orange><F4>
<Orange><F5>
<Orange><F6>
<Orange><F7>
<Orange><F8>
<Orange><F9>
<Orange><F10>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<Blue><q>
<Blue><w>
<Blue><e>
<Blue><r>
<Blue><t>
<Blue><y>
<Blue><u>
<Blue><i>
<Blue><o>
<Blue><p>
<Blue><a>
<Blue><s>
<▲>
<◄>
<▼>
<►>
<Orange><1>
<Orange><2>
<Orange><3>
<Orange><4>
<Orange><5>
<Orange><6>
<Orange><7>
<Orange><8>
<Orange><9>
<Orange><0>
9-27
Keypad Configuration
` grave accent
? question mark
/ forward slash
, comma
. period
~ tilde
^ carat
‘ apostrophe
& ampersand
| broken vertical bar
“ quotation mark
% percent
Alt
Attention
Backlight
Bottom
Clear
Clrfld
Clrtoend
ContrastContrast+
Ctrl
Delchar
Dup
EOF
Endpos
Esc
Field exit
FM
Field Field +
Help
Home
Insert
PA1
PA2
PA3
Page Down
Page Up
Print
Reset
Roll down
Roll up
Shift
Sys req
Tab
Top
View up
View down
View left
View right
VolVol+
9-28
<Orange><a>
<Orange><e>
<Orange><i>
<Orange><o>
<Orange><p>
<Orange><q>
<Orange><r>
<Orange><s>
<Orange><t>
<Orange><u>
<Orange><w>
<Orange><y>
----<Shift><F8>
--------<Blue><x>
<Blue><z>
<Orange><n>
--------<Orange><b>
--------------------<Orange><j>
<Orange><h>
--------<Orange><Space>
--<Orange><l>
--<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<Blue><v>
<Blue><c>
<Orange><a>
<Orange><e>
<Orange><i>
<Orange><o>
<Orange><p>
<Orange><q>
<Orange><r>
<Orange><s>
<Orange><t>
<Orange><u>
<Orange><w>
<Orange><y>
<Orange><m>
<Alt><7>
<Shift><F8>
--<Alt><F5>
<Alt><F7>
<Alt><F8>
<Blue><x>
<Blue><z>
<Orange><n>
<Alt><Del>
<Alt><F6>
<Alt><2>
<Orange><k>
<Orange><b>
--<Alt><4>
----<Alt><F9>
<Orange><g>
<Shift><F9>
<Alt><F10>
<Alt><F11>
<Alt><F12>
------<Alt><0>
----<Orange><Space>
<Shift><F7>
<Orange><l>
--<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<Blue><v>
<Blue><c>
<Orange><a>
<Orange><e>
<Orange><i>
<Orange><o>
<Orange><p>
<Orange><q>
<Orange><r>
<Orange><s>
<Orange><t>
<Orange><u>
<Orange><w>
<Orange><y>
<Orange><m>
<Alt><7>
<Shift><F8>
<Alt><8>
<Alt><F5>
<Alt><F7>
<Alt><F8>
<Blue><x>
<Blue><z>
<Orange><n>
<Alt><Del>
<Alt><F6>
--<Orange><k>
<Orange><b>
<Alt><9>
<Alt><4>
<Alt><2>
<Alt><.>
Alt><F9>
<Orange><g>
<Shift><F9>
----------<Alt><3>
<Alt><0>
<Alt><d>
<Alt><u>
<Orange><Space>
<Shift><F7>
<Orange><l>
<Alt><F10>
<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<Blue><v>
<Blue><c>
Twin Client Reference
• June, 2005
8260 ABC Diagrams
8260 ABC Diagrams
(8260 ABC diagrams begin on the next page.)
Twin Client Reference • June, 2005
9-29
Keypad Configuration
VT emulation
F11 F21 F12 F22
F1
F2
M1 “
~
a
A
`
K
F3
M2 ?
b
B
M11
k
cntrst+
‘
L
M3 ^
C
M12
l
M
U
M4 &
D
ctrl
e
E
vol+
N
o
O
vol- esc
w
W
M6
F7
|
g
F
pgup
end
G
pgdn
P
Q
p
q
y
Y
F18 F28 F19 F29 F20 F30
F8
M7
f
x
X
F17 F27
F6
M5 %
n
v
V
F5
d
m
cntrst-
F15 F25 F16 F26
F4
c
u
t
T
F13 F23 F14 F24
bklite
/ M8
,
H
tab
.
i
I
j
S
Del
Z
>
blue
▲
↑
*
}
4
$
{
(
-
5
6
:
\
=
2
1
3
#
@
►
→ ;
▼
↓
9
}
!
◄
←
+
8
7
_
{
M10
s
Space
orange
J
r
orange
F10
M9
h
R
shift
z
F9
<
0
Enter
)
blue
keytop
shift
9-30
alt
Twin Client Reference
• June, 2005
8260 ABC Table
3270 emulation
F11 F21 F12 F22
F1
F13 F23 F14 F24
F2
F3
F15 F25 F16 F26
F4
F5
F6
clr
M1 “
~
a
A
`
K
T
M2 ?
M3 ^
b
B
M11
‘
k
L
C
M12 alt
l
d
cntrst-
t
u
M
roll↑ V
vol+
N
v
O
vol- esc
F
pgup
|
F8
P
G
pgdn
/
M8
F9
Q
H
end
M9
F10
r
j
Del
dlchr
orange
▼
↓
(
-
}
4
5
6
fm :
}
!
;
@
0
\
=
2
1
)
9
attn *
$
{
►→
←
+
8
7
blue
▲
↑
◄
>
_
{
J
S
Z
orange
M10
s
Space
<
pa1
.
i
I
tab
R
shift
z
,
h
q
y
Y
M7
g
p
x
X
F7
f
o
w
W
M6
e
n
F18 F28 F19 F29 F20 F30
dup sreq clrfld bklite clrtnd ins help
M5 %
D roll↓ E
home
ctrl
m
cntrst+
U
c
M4 &
F17 F27
3
eof #
Enter
reset
blue
keytop
shift
Twin Client Reference • June, 2005
alt
9-31
Keypad Configuration
5250 emulation
F11 F21 F12 F22
F1
F13 F23 F14 F24
F2
F3
F15 F25 F16 F26
F4
F5
F6
clr
M1 “
~
a
A
`
‘
k
c
C
M12 alt
l
M
cntrst-
u
M6
|
M7
g
D roll↓ E
ctrl
home
F
pgup
G
pgdn
N
vol+
o
O
vol- esc
w
W
p
P
x
X
F8
F9
dup sreq clrfld bklite clrtnd ins help
M5 %
f
n
F18 F28 F19 F29 F20 F30
F7
e
v
U roll↑ V
M4 &
d
m
L
cntrst+
t
M3 ^
b
B
M11
K
T
M2 ?
F17 F27
q
Q
y
Y
/
M8
M9
h
H
end
r
j
▲
↑
◄
Del
Z
dlchr
orange
attn *
}
4
fm
$
{
:
@
\
=
3
fld- #
Enter
0
)
6
2
1
reset
blue
keytop
shift
9-32
alt
Twin Client Reference
fldx
bot (
-
}
!
▼
↓
9
5
►
→ ;
←
+
8
7
blue
J
S
>
_
{
M10
s
Space
orange
top
.
i
I
tab
R
shift
z
,
F10
<
• June, 2005
print
8260 ABC Table
8260 ABC Table
Key
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Del
Enter
Space
1
2
3
4
5
6
VTERM
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Del>
<Enter>
<Space>
<1>
<2>
<3>
<4>
<5>
<6>
Twin Client Reference • June, 2005
3270
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Del>
<Enter>
<Space>
<1>
<2>
<3>
<4>
<5>
<6>
5250
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Del>
<Enter>
<Space>
<1>
<2>
<3>
<4>
<5>
<6>
9-33
Keypad Configuration
7
8
9
0
!
exclamation
@ at sign
# pound
$ dollar
:
colon
\
backward slash
_ underscore
*
asterisk
(
left parenthesis
)
right parenthesis
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
M1
M2
M3
M4
M5
M6
M7
M8
M9
M10
M11
M12
▲
◄
▼
►
{ left brace
} right brace
= equal sign
[ left bracket
] right bracket
- hyphen
< less-than sign
> greater-than sign
+ addition sign
; semicolon
` grave accent
? question mark
9-34
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<Orange><F1>
<Orange><F2>
<Orange><F3>
<Orange><F4>
<Orange><F5>
<Orange><F6>
<Orange><F7>
<Orange><F8>
<Orange><F9>
<Orange><F10>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<Blue><a>
<Blue><b>
<Blue><c>
<Blue><d>
<Blue><e>
<Blue><f>
<Blue><g>
<Blue><h>
<Blue><i>
<Blue><j>
<Blue><k>
<Blue><l>
<▲>
<◄>
<▼>
<►>
<Orange><1>
<Orange><2>
<Orange><3>
<Orange><4>
<Orange><5>
<Orange><6>
<Orange><7>
<Orange><8>
<Orange><9>
<Orange><0>
<Orange><k>
<Orange><c>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<Orange><F1>
<Orange><F2>
<Orange><F3>
<Orange><F4>
<Orange><F5>
<Orange><F6>
<Orange><F7>
<Orange><F8>
<Orange><F9>
<Orange><F10>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<Blue><a>
<Blue><b>
<Blue><c>
<Blue><d>
<Blue><e>
<Blue><f>
<Blue><g>
<Blue><h>
<Blue><i>
<Blue><j>
<Blue><k>
<Blue><l>
<▲>
<◄>
<▼>
<►>
<Orange><1>
<Orange><2>
<Orange><3>
<Orange><4>
<Orange><5>
<Orange><6>
<Orange><7>
<Orange><8>
<Orange><9>
<Orange><0>
<Orange><k>
<Orange><c>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<Orange><F1>
<Orange><F2>
<Orange><F3>
<Orange><F4>
<Orange><F5>
<Orange><F6>
<Orange><F7>
<Orange><F8>
<Orange><F9>
<Orange><F10>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<Blue><a>
<Blue><b>
<Blue><c>
<Blue><d>
<Blue><e>
<Blue><f>
<Blue><g>
<Blue><h>
<Blue><i>
<Blue><j>
<Blue><k>
<Blue><l>
<▲>
<◄>
<▼>
<►>
<Orange><1>
<Orange><2>
<Orange><3>
<Orange><4>
<Orange><5>
<Orange><6>
<Orange><7>
<Orange><8>
<Orange><9>
<Orange><0>
<Orange><k>
<Orange><c>
Twin Client Reference
• June, 2005
8260 ABC Table
/ forward slash
, comma
. period
~ tilde
^ carat
‘ apostrophe
& ampersand
| broken vertical bar
“ quotation mark
% percent
Alt
Attention
Backlight
Bottom
Clear
Clrfld
Clrtoend
ContrastContrast+
Ctrl
Delchar
Dup
EOF
End
Esc
Field exit
FM
Field Field +
Help
Home
Insert
PA1
PA2
PA3
Page Down
Page Up
Print
Reset
Roll down
Roll up
Shift
Sys req
Tab
Top
View up
View down
View left
View right
VolVol+
<Orange><h>
<Orange><i>
<Orange><j>
<Orange><a>
<Orange><d>
<Orange><l>
<Orange><e>
<Orange><g>
<Orange><b>
<Orange><f>
----<Shift><F8>
--------<Blue><u>
<Blue><t>
<Orange><Del>
--------<Orange><x>
--------------------<Orange><q>
<Orange><p>
--------<Orange><Space>
--<Orange><s>
--<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<Blue><w>
<Blue><v>
Twin Client Reference • June, 2005
<Orange><h>
<Orange><i>
<Orange><j>
<Orange><a>
<Orange><d>
<Orange><l>
<Orange><e>
<Orange><g>
<Orange><b>
<Orange><f>
<Orange><z>
<Alt><7>
<Shift><F8>
--<Alt><F5>
<Alt><F7>
<Alt><F8>
<Blue><u>
<Blue><t>
<Orange><Del>
<Alt><Del>
<Alt><F6>
<Alt><2>
<Orange><r>
<Orange><x>
--<Alt><4>
----<Alt><F9>
<Orange><o>
<Shift><F9>
<Alt><F10>
<Alt><F11>
<Alt><F12>
------<Alt><0>
----<Orange><Space>
<Shift><F7>
<Orange><s>
--<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<Blue><w>
<Blue><v>
<Orange><h>
<Orange><i>
<Orange><j>
<Orange><a>
<Orange><d>
<Orange><l>
<Orange><e>
<Orange><g>
<Orange><b>
<Orange><f>
<Orange><z>
<Alt><7>
<Shift><F8>
<Alt><8>
<Alt><F5>
<Alt><F7>
<Alt><F8>
<Blue><u>
<Blue><t>
<Orange><Del>
<Alt><Del>
<Alt><F6>
--<Orange><r>
<Orange><x>
<Alt><9>
<Alt><4>
<Alt><2>
<Alt><.>
Alt><F9>
<Orange><o>
<Shift><F9>
----------<Alt><3>
<Alt><0>
<Alt><d>
<Alt><u>
<Orange><Space>
<Shift><F7>
<Orange><s>
<Alt><F10>
<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<Blue><w>
<Blue><v>
9-35
Keypad Configuration
8260 AZERTY Diagrams
(8260 AZERTY diagrams begin on the next page.)
9-36
Twin Client Reference
• June, 2005
8260 AZERTY Diagrams
VT emulation
F11 F21 F12 F22
F1
F2
M1 “
~
a
A
`
Q
‘
M2 ?
e
E
F5
M4 &
r
s
d
T
f
F
vol+
c
C
g
G
vol- esc
v
V
M6
t
R
|
F8
M7
U
pgdn
H
ctrl
J
h
n
M9
k
.
Del
blue
orange
p
>
blue
*
}
4
$
{
▲
↑
5
:
▼
↓
@
alt
0
6
\
=
2
1
►
→ ;
9
(
-
}
!
◄
←
+
8
7
_
{
P
L
M
<
M10
l
Space
orange
F10
o
O
tab
K
shift
m
,
i
I
j
F9
bklite
/ M8
u
Y
pgup
end
N
F18 F28 F19 F29 F20 F30
F7
y
b
B
F17 F27
F6
M5 %
M12
x
X
F15 F25 F16 F26
F4
M3 ^
S
D
cntrst+ cntrst-
w
W
F3
z
Z
M11
q
F13 F23 F14 F24
3
#
Enter
)
clr
keytop
shift
Twin Client Reference • June, 2005
alt
9-37
Keypad Configuration
3270 emulation
F11 F21 F12 F22
F1
F13 F23 F14 F24
F2
F3
F15 F25 F16 F26
F4
F5
F6
clr
M1 “
~
a
A
`
Q
z
Z
M11
q
‘
M3 ^
e
E
M12
s
f
c
X
C
T
home
v
V
M6
Y
pgup
|
F8
H
ctrl
/
M8
F9
j
J
alt
M9
◄
Del
dlchr
M
orange
attn *
▼
↓
5
fm :
}
!
;
@
\
=
3
eof #
Enter
0
)
6
2
1
►→
←
4
9
(
-
}
$
{
▲
↑
+
8
7
blue
P
L
>
_
{
M10
l
Space
orange
pa1
.
p
O
tab
<
F10
o
k
K
shift
m
,
i
U roll↑ I
end
pgdn
n
N
M7
u
h
b
B
F7
y
g
G
vol- esc
F18 F28 F19 F29 F20 F30
dup sreq clrfld bklite clrtnd ins help
M5 %
t
R
d
x
M4 &
r
S
D roll↓ F
cntrst+ cntrst- vol+
w
W
M2 ?
F17 F27
reset
blue
keytop
shift
9-38
alt
Twin Client Reference
• June, 2005
8260 AZERTY Diagrams
5250 emulation
F11 F21 F12 F22
F1
F13 F23 F14 F24
F2
F3
F15 F25 F16 F26
F4
F5
F6
clr
M1 “
~
a
A
`
Q
z
Z
M11
q
‘
M3 ^
e
E
M4 &
R
s
d
f
x
X
c
C
v
V
Y
pgup
F8
H
ctrl
M7
u
F9
M8
,
M9
o
U roll↑ I
end
pgdn
O
tab
j
J
alt
n
N
/
i
h
b
B
|
y
g
G
vol- esc
F7
M6
t
T
home
M12
F18 F28 F19 F29 F20 F30
dup sreq clrfld bklite clrtnd ins help
M5 %
r
S
D roll↓ F
cntrst+ cntrstvol+
w
W
M2 ?
F17 F27
k
K
shift
m
Space
F10
.
▲
↑
◄
Del
attn *
}
4
fm
$
{
:
@
0
)
6
\
=
2
1
3
fld- #
Enter
reset
blue
keytop
shift
Twin Client Reference • June, 2005
fldx
bot (
-
}
!
▼
↓
9
5
►
→ ;
←
+
8
7
blue
P
L
>
_
{
M10
p
dlchr
orange
orange
top
l
M
<
alt
9-39
print
Keypad Configuration
8260 AZERTY Table
Key
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Del
Enter
Space
1
2
3
4
9-40
VTERM
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Del>
<Enter>
<Space>
<1>
<2>
<3>
<4>
3270
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Del>
<Enter>
<Space>
<1>
<2>
<3>
<4>
5250
<a>
<b>
<c>
<d>
<e>
<f>
<g>
<h>
<i>
<j>
<k>
<l>
<m>
<n>
<o>
<p>
<q>
<r>
<s>
<t>
<u>
<v>
<w>
<x>
<y>
<z>
<Shift><a>
<Shift><b>
<Shift><c>
<Shift><d>
<Shift><e>
<Shift><f>
<Shift><g>
<Shift><h>
<Shift><i>
<Shift><j>
<Shift><k>
<Shift><l>
<Shift><m>
<Shift><n>
<Shift><o>
<Shift><p>
<Shift><q>
<Shift><r>
<Shift><s>
<Shift><t>
<Shift><u>
<Shift><v>
<Shift><w>
<Shift><x>
<Shift><y>
<Shift><z>
<Del>
<Enter>
<Space>
<1>
<2>
<3>
<4>
Twin Client Reference
• June, 2005
8260 AZERTY Table
5
6
7
8
9
0
!
exclamation
@ at sign
# pound
$ dollar
:
colon
\
backward slash
_ underscore
*
asterisk
(
left parenthesis
)
right parenthesis
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
M1
M2
M3
M4
M5
M6
M7
M8
M9
M10
M11
M12
▲
◄
▼
►
{ left brace
} right brace
= equal sign
[ left bracket
] right bracket
- hyphen
< less-than sign
> greater-than sign
+ addition sign
; semicolon
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<Orange><F1>
<Orange><F2>
<Orange><F3>
<Orange><F4>
<Orange><F5>
<Orange><F6>
<Orange><F7>
<Orange><F8>
<Orange><F9>
<Orange><F10>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<Blue><a>
<Blue><z>
<Blue><e>
<Blue><r>
<Blue><t>
<Blue><y>
<Blue><u>
<Blue><i>
<Blue><o>
<Blue><p>
<Blue><q>
<Blue><s>
<▲>
<◄>
<▼>
<►>
<Orange><1>
<Orange><2>
<Orange><3>
<Orange><4>
<Orange><5>
<Orange><6>
<Orange><7>
<Orange><8>
<Orange><9>
<Orange><0>
Twin Client Reference • June, 2005
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<Orange><F1>
<Orange><F2>
<Orange><F3>
<Orange><F4>
<Orange><F5>
<Orange><F6>
<Orange><F7>
<Orange><F8>
<Orange><F9>
<Orange><F10>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<Blue><a>
<Blue><z>
<Blue><e>
<Blue><r>
<Blue><t>
<Blue><y>
<Blue><u>
<Blue><i>
<Blue><o>
<Blue><p>
<Blue><q>
<Blue><s>
<▲>
<◄>
<▼>
<►>
<Orange><1>
<Orange><2>
<Orange><3>
<Orange><4>
<Orange><5>
<Orange><6>
<Orange><7>
<Orange><8>
<Orange><9>
<Orange><0>
<5>
<6>
<7>
<8>
<9>
<0>
<Shift><1>
<Shift><2>
<Shift><3>
<Shift><4>
<Shift><5>
<Shift><6>
<Shift><7>
<Shift><8>
<Shift><9>
<Shift><0>
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
<Orange><F1>
<Orange><F2>
<Orange><F3>
<Orange><F4>
<Orange><F5>
<Orange><F6>
<Orange><F7>
<Orange><F8>
<Orange><F9>
<Orange><F10>
<Blue><F1>
<Blue><F2>
<Blue><F3>
<Blue><F4>
<Blue><a>
<Blue><z>
<Blue><e>
<Blue><r>
<Blue><t>
<Blue><y>
<Blue><u>
<Blue><i>
<Blue><o>
<Blue><p>
<Blue><q>
<Blue><s>
<▲ >
<◄ >
<▼ >
<► >
<Orange><1>
<Orange><2>
<Orange><3>
<Orange><4>
<Orange><5>
<Orange><6>
<Orange><7>
<Orange><8>
<Orange><9>
<Orange><0>
9-41
Keypad Configuration
` grave accent
? question mark
/ forward slash
, comma
. period
~ tilde
^ carat
‘ apostrophe
& ampersand
| broken vertical bar
“ quotation mark
% percent
Alt
Attention
Backlight
Bottom
Clear
Clrfld
Clrtoend
ContrastContrast+
Ctrl
Delchar
Dup
EOF
End
Esc
Field exit
FM
Field Field +
Help
Home
Insert
PA1
PA2
PA3
Page Down
Page Up
Print
Reset
Roll down
Roll up
Shift
Sys req
Tab
Top
View up
View down
View left
View right
VolVol+
9-42
<Orange><q>
<Orange><e>
<Orange><i>
<Orange><o>
<Orange><p>
<Orange><a>
<Orange><r>
<Orange><s>
<Orange><t>
<Orange><u>
<Orange><z>
<Orange><y>
----<Shift><F8>
--------<Blue><x>
<Blue><w>
<Orange><n>
--------<Orange><b>
--------------------<Orange><j>
<Orange><h>
--------<Orange><Space>
--<Orange><l>
--<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<Blue><v>
<Blue><c>
<Orange><q>
<Orange><e>
<Orange><i>
<Orange><o>
<Orange><p>
<Orange><a>
<Orange><r>
<Orange><s>
<Orange><t>
<Orange><u>
<Orange><z>
<Orange><y>
<Orange><m>
<Alt><7>
<Shift><F8>
--<Alt><F5>
<Alt><F7>
<Alt><F8>
<Blue><x>
<Blue><w>
<Orange><n>
<Alt><Del>
<Alt><F6>
<Alt><2>
<Orange><k>
<Orange><b>
--<Alt><4>
----<Alt><F9>
<Orange><g>
<Shift><F9>
<Alt><F10>
<Alt><F11>
<Alt><F12>
------<Alt><0>
----<Orange><Space>
<Shift><F7>
<Orange><l>
--<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<Blue><v>
<Blue><c>
<Orange><q>
<Orange><e>
<Orange><i>
<Orange><o>
<Orange><p>
<Orange><a>
<Orange><r>
<Orange><s>
<Orange><t>
<Orange><u>
<Orange><z>
<Orange><y>
<Orange><m>
<Alt><7>
<Shift><F8>
<Alt><8>
<Alt><F5>
<Alt><F7>
<Alt><F8>
<Blue><x>
<Blue><w>
<Orange><n>
<Alt><Del>
<Alt><F6>
--<Orange><k>
<Orange><b>
<Alt><9>
<Alt><4>
<Alt><2>
<Alt><.>
Alt><F9>
<Orange><g>
<Shift><F9>
----------<Alt><3>
<Alt><0>
<Alt><d>
<Alt><u>
<Orange><Space>
<Shift><F7>
<Orange><l>
<Alt><F10>
<Alt><▲>
<Alt><▼>
<Alt><◄>
<Alt><►>
<Blue><v>
<Blue><c>
Twin Client Reference
• June, 2005
Chapter 10 • Error Message Resolution Guide
Message
Reason
ENTRY TOO LONG;
Trying to key beyond the field size. Ensure that you are entering input into the
correct field.
---
ALPHABETIC ONLY;
Trying to key a character that is not Ensure that you are entering input into the
alphabetic.
correct field.
---
MINUS NOT VALID;
Trying to key a Minus sign.
Ensure that you are entering input into the
correct field.
---
DECIMAL NOT VALID;
Trying to key a Decimal (period).
Ensure that you are entering input into the
correct field.
---
ALPHANUMERIC ONLY;
Trying to key characters other than Ensure that you are entering input into the
Alphabetic and numeric.
correct field.
---
NUMERIC ONLY;
Trying to key characters other than Ensure that you are entering input into the
numeric.
correct field.
---
ENTRY TOO SHORT;
Trying to exit the field before it is
filled.
Ensure that you are entering input into the
correct field.
---
INVALID KEY;
The key pressed is not valid.
Ensure that you are entering input into the
correct field.
---
Twin Client Reference
• June, 2005
Solution
Reference Tech Note
10-1
Error Message Resolution Guide
Message
Reason
Solution
Reference Tech Note
MUST CLEAR FIELD;
Trying to enter data in a field that
must be cleared first.
Ensure that you are entering input into the
correct field.
---
SCAN NOT ALLOWED;
Trying to scan into a key only field. Ensure that you are entering input into the
correct field.
---
KEY NOT ALLOWED;
Trying to key into a scan only field. Ensure that you are entering input into the
correct field.
---
ENTRY TOO SHORT;
Trying to exit the field before it is
filled.
Ensure that you are entering input into the
correct field.
---
RECOVERABLE ERROR;
Encountered an error from which
you can continue.
Verify that your configuration settings for the
hardware being used, usually a printer and
cable issue.
---
UNRECOVERABLE ERROR;
Encountered an error from which
you can NOT continue.
Verify that your Network settings are correct T1113, T1114, T1161,
and you are in the correct mode using the T1171, T1187 and
correct Port.
T1194
FUNCTION: \n\nFILE: \nLINE: \nCODE; Encountered an error from which
you can NOT continue.
Notify Connect over the WEB incident
reporting system.
---
Press any key\nFor More Details...;
Press Enter for more information.
Advisory message.
---
Press any key;
Press a key to continue.
Advisory message.
---
Connection ERROR.\nREBOOT
MOBILE UNIT;
Could not Connect.
Verify that your Network settings are correct T1113, T1114, T1161,
and you are in the correct mode using the T1171, T1187 and
correct Port.
T1194
10-2
Twin Client Reference
• June, 2005
Error Message Resolution Guide
Message
Reason
Solution
Reference Tech Note
Disconnect ERROR.\nREBOOT
MOBILE UNIT;
Could not Disconnect.
Verify that your Network settings are correct T1113, T1114, T1161,
and you are in the correct mode using the T1171, T1187 and
correct Port.
T1194
RF Send ERROR.\nREBOOT MOBILE Could not Send.
UNIT;
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
RF Receive ERROR.\nREBOOT
MOBILE UNIT;
Could not Receive.
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
RF Check ERROR.\nREBOOT
MOBILE UNIT;
Could not run the RF Survey.
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
RF Timeout ERROR.\nREBOOT
MOBILE UNIT;
Have been trying to contact the
Most likely a range, access point, radio,
host for the radio timeout period (2 host or network issue. Troubleshoot the
minutes default).
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
REBOOT MOBILE UNIT;
Reboot the Mobile Unit do to loss
of connection.
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
Retry (Y/N)?;
Try again.
Try to send or receive again, or perhaps
ensure that the printer is cabled to the
Mobile Unit and is on.
---
TIMEOUT\n\nSending Data;
Mobile Unit out of the coverage
area.
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
Twin Client Reference • June, 2005
10-3
Error Message Resolution Guide
Message
Reason
Solution
Reference Tech Note
TIMEOUT\n\nReceiving Data;
Mobile Unit out of the coverage
area.
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
Host Received Data\nAwaiting App
Reply!;
Mobile Unit has sent and received
an acknowledgement from the IP
stack and is waiting for the
application to return data.
Most likely a host or network issue.
Troubleshoot the customer’s environment.
Probable causes are Database record
locking, application program failure, Host
failure or network failure.
T1113, T1114, T1161,
T1171, T1187 and
T1194
* WAITING TO SEND *;
Mobile Unit out of the coverage
area.
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
TCP Error Reading\nMAC
Address.\nREBOOT MOBILE UNIT;
Could not obtain the Mac Address Possible hardware, driver or stack problem
from the Mobile Unit.
Contact the Mobile Unit manufacturer.
---
Invalid TIP Command;
Bad internal protocol.
Notify Connect over the WEB incident
reporting system.
---
Session Ended\nBy User or Host;
User, Host, application or network
has ended the session.
If the user did not end the session, most
likely host or network issues. Troubleshoot
the customer’s environment.
Server Packet Error;
Bad Protocol detected.
Usually a result of bad cabling, power or
faulty transceiver. Also, will receive this if
the Mobile Unit is in the wrong mode for
server operation.
---
Error receiving host\nlist from Server;
Bad Protocol detected.
Usually a result of bad cabling, power or
faulty transceiver. Also, will receive this if
the Mobile Unit is in the wrong mode for
server operation.
---
10-4
T1113, T1114, T1161,
T1171, T1187 and
T1194
Twin Client Reference
• June, 2005
Error Message Resolution Guide
Message
Reason
Solution
Unexpected Server\ndata received;
Bad Protocol detected.
---
Error starting\nhost application;
Connected to the server but can
not connect to the distant end.
Usually a result of bad cabling, power or
faulty transceiver. Also, will receive this if
the Mobile Unit is in the wrong mode for
server operation.
Configure the server handler to access the
host application.
Select Host or App;
Need to choose your
Host/application destination.
User selection required.
---
Connecting...;
Attempting to connect to the
Host/application.
Advisory message.
---
TCP Error\nReading IP
Address\nREBOOT MOBILE UNIT;
Mobile Unit missing Network IP
information.
Configure the Mobile Unit with the correct
network IP information.
---
Printer start error;
Could not initialize the printer.
Cable or power issue with the printer.
---
Battery too low\nto print;
Not enough power to print.
Replace the battery with a fully recharged
battery.
---
Paper Feed Error\nFix Then Hit Enter;
Paper in the printer is not ready.
Replace the paper or rethread the paper in
the printer.
---
Printer Error\nPrint Ended;
Can not print.
Check cable, battery, communication
settings and paper in the printer.
---
User Count Exceeded.\n Session
Ended;
Possible authorization issue.
Verify that you have the correct number of
licenses for the number of Mobile Units you
are using.
---
Twin Client Reference • June, 2005
Reference Tech Note
---
10-5
Error Message Resolution Guide
Message
Reason
Solution
Reference Tech Note
Primary Unavailable\nTrying Alternate; First Host IP address not available Verify the host address.
trying the remaining addresses in
the Host list.
---
APMAC.DAT Error\nSession Ended;
Access point Media Access Control Most likely a range, access point, radio,
error.
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
MUIP.DAT Error\nSession Ended;
Mobile Unit IP Error.
Most likely a Mobile Unit network setting
issue. Troubleshoot the customer’s
environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
Missing Subnet IP\nSession Ended;
Mobile Unit IP Netmask Error.
Most likely a Mobile Unit network setting
issue. Troubleshoot the customer’s
environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
Error Opening File;
File is missing.
Verify that the configuration files are on the
Mobile Unit. Or perhaps there is a
hardware failure.
---
Telnet API\nnot found;
Program files are missing.
Reload program files.
---
Battery Low Warning\n\nReplace
Battery Soon;
Not enough power to operate the
Mobile Unit.
Replace the battery with a fully recharged
battery.
---
No Host List.\nPress any key\nTo Edit
Host IP's;
Have not configured your target
hosts.
Configure the target host IP addresses.
---
Unable to Allocate\nFont Memory;
Mobile Unit does not have enough Reduce the fonts in use or expand the
memory to load the fonts.
memory in the Mobile Unit.
---
Font Loading Error;
Could not load the font.
---
10-6
Ensure that the font is available to load.
Twin Client Reference
• June, 2005
Error Message Resolution Guide
Message
Reason
Solution
Reference Tech Note
Printer Not Ready\nPress R to Retry\nC Can not print.
to Cancel Print;
Check cable, battery, communication
settings and paper in the printer.
---
Mobile Unit in\nDemonstration
Mode\nfor TwinClient;
Running in demo mode.
Purchase a license from Connect.
---
Connected to Host;
Successful connection to the target Advisory message.
Host.
---
Telnet Mode not\nsupported on\nthis
Mobile Unit;
Telnet Setup files\nnot found.
Reload\nfiles then switch;
This Mobile Unit must be used with Order a Connect Server.
a Connect Server.
Customer specific configuration
Load the configuration files into the Mobile
files are missing.
Unit from Twin Client Manager.
-----
Switched Client to\nTelnet Direct Mode; Mobile Unit running in Telnet mode Advisory message.
direct to the target Host.
---
Switched Client to\nServer Based
Mode;
Mobile Unit running through a
Connect server in server mode
usually at port 1800.
Advisory message.
---
Port 23 is only\nallowed in Telnet
Mode;
Can not set the port to 23 in server Advisory message.
mode. Port 23 is the standard
Telnet port.
---
Not Enough Memory\nTo Run;
Mobile Unit does not have the
capacity to run the program do to
memory restrictions.
Expand the Mobile Unit memory.
---
Press any key;
Press a key to continue.
Advisory message.
---
TwinClient Telnet;
Prompt.
Advisory message.
---
Twin Client Reference • June, 2005
10-7
Error Message Resolution Guide
Message
Reason
Solution
TwinClient Server;
Prompt.
Advisory message.
---
TwinClient TN3270;
Prompt.
Advisory message.
---
TwinClient TN5250;
Prompt.
Advisory message.
---
TwinClient TNVT/HP;
Prompt.
Advisory message.
---
(c) 1991-2005 Connect;
Prompt.
Advisory message.
---
Edit Menu Options;
Menu Title.
Advisory message.
---
Edit Mobile Unit IP;
Menu Option.
Advisory message.
---
Edit Server/Host IPs;
Menu Option.
Advisory message.
---
Edit Radio Option;
Menu Option.
Advisory message.
---
Edit License Key;
Menu Option.
Advisory message.
---
10-8
Reference Tech Note
Twin Client Reference
• June, 2005
Error Message Resolution Guide
Message
Reason
Solution
Run Site Survey;
Menu Option.
Advisory message.
---
Switch Client Modes;
Menu Option.
Advisory message.
---
Run TwinClient;
Menu Option.
Advisory message.
---
Exit to OS;
Menu Option.
Advisory message.
---
Printer may not be\nplugged in
or\nturned on!;
Can not print.
Check cable, battery, communication
settings and paper in the printer.
---
OUT OF RANGE OF BASE;
Mobile Unit out of the coverage
area.
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
CONNECT SERIAL CABLE;
Serial cable not connected to the
Mobile Unit.
Check cable, battery and communication
settings for the Mobile Unit.
---
REMOVE SERIAL CABLE;
Remove serial cable from to the
Mobile Unit.
Check cable, battery and communication
settings for the Mobile Unit.
---
PLACE IN CRADLE;
Place the Mobile Unit in the cradle. Advisory message.
---
REMOVE FROM CRADLE;
Remove Mobile Unit from the
cradle.
---
Twin Client Reference • June, 2005
Advisory message.
Reference Tech Note
10-9
Error Message Resolution Guide
Message
Reason
Solution
ACQUIRING CRADLE BUS;
Attempting to access the cradle
through the serial port you have
configured.
Advisory message.
Printer Out\nOf Range;
Printer out of the coverage area.
Most likely a range, access point or radio
issue. Troubleshoot the customer’s
environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
Connection Refused\nBy Host;
You connected to the target host
but the host disconnected you.
Verify that the configuration file has the
correct Mobile Unit type and New
environment variable set. Fallback to the
Connect Default to verify the connection.
---
Connection Timed Out;
You connected to the host but did Modify the Host parameters for login.
not logon in the appropriate time so
the host disconnected you.
Connection Failed\nHost Not
Responding;
Could not connect to the Host.
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
Connection Failed\nHost Unreachable; Could not connect to the Host.
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
Mobile Unit Out\nOf Range,
Unable\nTo Transmit;
Mobile Unit out of the coverage
area.
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
Mobile Unit Out\nOf Range,
Unable\nTo Receive;
Mobile Unit out of the coverage
area.
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
---
Printer Not\nResponding;
Can not print.
Check cable, battery, communication
settings and paper in the printer.
---
10-10
Reference Tech Note
---
---
Twin Client Reference
• June, 2005
Error Message Resolution Guide
Message
Reason
Solution
Reference Tech Note
Printer Out\nOf Range;
Printer out of the coverage area.
Most likely a range, access point or radio
issue. Troubleshoot the customer’s
environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
Print Complete;
Prompt.
Advisory message.
---
Reprint (Y/N)?;
Yes or No prompt for a reprint.
Advisory message.
---
WARNING;
Prompt.
Advisory message.
---
Turning power off\nduring a
session\nwill cause the\nprogram to
restart;
This Mobile Unit will disconnect the Mobile Unit manufacturer limitation.
session if powered off.
Advisory message.
---
Are you sure (y/n)?;
Yes or No prompt for a
confirmation.
Advisory message.
---
You Sure? (YyNn);
Yes or No prompt for a
confirmation.
Advisory message.
---
Domain Name Server\nNot Set;
DOMAIN NAME SERVER not
configured.
Configure the Mobile Unit with the correct
network IP information.
---
Domain Name Server\nQuery Memory Memory error on the Mobile Unit
Error;
Expand the Mobile Unit memory or return
the Mobile Unit for repair.
---
Domain Name Server\nQuery Sending Mobile Unit out of the coverage
Error;
area.
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
Twin Client Reference • June, 2005
T1113, T1114, T1161,
T1171, T1187 and
T1194
10-11
Error Message Resolution Guide
Message
Reason
Solution
Reference Tech Note
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
Domain Name Server\nUnavailable;
Could not connect to the DOMAIN Most likely a range, access point, radio,
NAME SERVER.
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
Error loading\nparameter file;
Could not load the parameter file.
Reload the correct configuration files.
---
Could not open\ntelnet interface;
Could not telnet.
Reload the program files.
---
Could not set\mtelnet options;
Could not use the telnet
configuration.
Reload the correct configuration files.
---
Setup file\nsetting mismatch\nReload
Setup;
Emulation program selected is not Remove the emulation and configuration
compatible with the configuration files. Run clear Telnet on the Mobile Unit
file on the Mobile Unit.
then reload the Mobile Unit with the proper
emulation and configuration files.
---
Display formatting\ntoo large
for\ncurrent screen;
Mobile Unit does not have enough Expand the Mobile Unit memory or order a
memory to run your configured
server from Connect.
reformatted screens.
---
Mobile Unit\ninitialization error;
Mobile Unit problem.
---
Domain Name Server\nQuery Receive Mobile Unit out of the coverage
Error;
area.
Host/App/Network\nclosed the session; Customer’s environment
disconnected the Mobile Unit
session.
10-12
Return the Mobile Unit to the manufacturer
for repair.
Most likely a range, access point, radio,
host or network issue. Troubleshoot the
customer’s environment.
T1113, T1114, T1161,
T1171, T1187 and
T1194
Twin Client Reference
• June, 2005
Error Message Resolution Guide
Message
Reason
Solution
Disconnecting...;
Prompt.
Advisory message.
---
Scan Barcode;
Bar code scanning test.
Advisory message.
---
Enter Setup\nPassword;
Prompt.
Advisory message.
---
Enter Profile \nPassword;
Prompt.
Advisory message.
---
Host IP;
Host IP address prompt.
Enter target host IP address.
---
Host Name;
Host name prompt.
Enter target host Name.
---
Port;
Host IP port required.
Enter 23 for telnet or 1800 for a Connect
server. Could also be a different number
depending on the customer’s environment.
Mobile Unit Type;
Prompt.
Advisory message.
---
WARNING: This will \nend any\ncurrent Prompt.
session;
Advisory message.
---
Continue (Y/N)?;
Advisory message.
---
Twin Client Reference • June, 2005
Prompt.
Reference Tech Note
T1113, T1114, T1161,
T1171, T1187 and
T1194
10-13
Error Message Resolution Guide
Message
Reason
Solution
HOST ENTRY;
Prompt.
Advisory message.
---
VT(100/220)/HP Setup;
Prompt.
Advisory message.
---
Mobile Unit Info;
Prompt.
Advisory message.
---
Emulation Setup;
Prompt.
Advisory message.
---
ANSI Setup;
Prompt.
Advisory message.
---
Miscellaneous Setup;
Prompt.
Advisory message.
---
Mobile Unit Type;
Prompt.
Advisory message.
---
Control Codes;
Prompt.
Advisory message.
---
Local Echo;
Prompt.
Advisory message.
---
<BK SP> Sends;
Prompt.
Advisory message.
---
10-14
Reference Tech Note
Twin Client Reference
• June, 2005
Error Message Resolution Guide
Message
Reason
Solution
New Line Mode;
Prompt.
Advisory message.
---
Insert Mode;
Prompt.
Advisory message.
---
Autowrap Mode;
Prompt.
Advisory message.
---
Cursor;
Prompt.
Advisory message.
---
EMULATION SETUP;
Prompt.
Advisory message.
---
Mobile Unit Type;
Prompt.
Advisory message.
---
Local Echo;
Prompt.
Advisory message.
---
Map Underline;
Prompt.
Advisory message.
---
Break Key;
Prompt.
Advisory message.
---
ANSI Setup;
Prompt.
Advisory message.
---
Twin Client Reference • June, 2005
Reference Tech Note
10-15
Error Message Resolution Guide
Message
Reason
Solution
Control Codes;
Prompt.
Advisory message.
---
Backspace Key;
Prompt.
Advisory message.
---
MISCELLANEOUS SETUP;
Prompt.
Advisory message.
---
Test Options;
Prompt.
Advisory message.
---
Login Options;
Prompt.
Advisory message.
---
TEST OPTIONS;
Prompt.
Advisory message.
---
Printer Test;
Prompt.
Advisory message.
---
Scan Code Test;
Prompt.
Advisory message.
---
LOGIN OPTIONS;
Prompt.
Advisory message.
---
User Name;
Prompt.
Advisory message.
---
10-16
Reference Tech Note
Twin Client Reference
• June, 2005
Error Message Resolution Guide
Message
Reason
Solution
User Password;
Prompt.
Advisory message.
---
ON;
Prompt.
Advisory message.
---
OFF;
Prompt.
Advisory message.
---
Map;
Prompt.
Advisory message.
---
Don't Map;
Prompt.
Advisory message.
---
Enable Break;
Prompt.
Advisory message.
---
Disable Break;
Prompt.
Advisory message.
---
7 bit;
Prompt.
Advisory message.
---
8 bit;
Prompt.
Advisory message.
---
Send Delete;
Prompt.
Advisory message.
---
Twin Client Reference • June, 2005
Reference Tech Note
10-17
Error Message Resolution Guide
Message
Reason
Solution
Send Backspace;
Prompt.
Advisory message.
---
Mobile Unit Setup;
Prompt.
Advisory message.
---
Scanner Options;
Prompt.
Advisory message.
---
Program Options;
Prompt.
Advisory message.
---
Special Options;
Prompt.
Advisory message.
---
Beeper Options;
Prompt.
Advisory message.
---
Exit to DOS;
Prompt.
Advisory message.
---
Backlight Time;
Prompt.
Advisory message.
---
Enter Key Action;
Prompt.
Advisory message.
---
Reset Options;
Prompt.
Advisory message.
---
10-18
Reference Tech Note
Twin Client Reference
• June, 2005
Error Message Resolution Guide
Message
Reason
Solution
Font Size;
Prompt.
Advisory message.
---
Portable Printer;
Prompt.
Advisory message.
---
Reprint Option;
Prompt.
Advisory message.
---
Data IDs;
Prompt.
Advisory message.
---
Internal/External;
Prompt.
Advisory message.
---
Modify Beeps;
Prompt.
Advisory message.
---
Message Beeps;
Prompt.
Advisory message.
---
Scan Identifier;
Prompt.
Advisory message.
---
AID Scan Setup;
Prompt.
Advisory message.
---
Long Scans;
Prompt.
Advisory message.
---
Twin Client Reference • June, 2005
Reference Tech Note
10-19
Error Message Resolution Guide
Message
Reason
Solution
Scan Send;
Prompt.
Advisory message.
---
Yes;
Prompt.
Advisory message.
---
No;
Prompt.
Advisory message.
---
Normal;
Prompt.
Advisory message.
---
Double Wide;
Prompt.
Advisory message.
---
Double High;
Prompt.
Advisory message.
---
Double High and Wide;
Prompt.
Advisory message.
---
Errors Only;
Prompt.
Advisory message.
---
Automatic;
Prompt.
Advisory message.
---
All Messages;
Prompt.
Advisory message.
---
10-20
Reference Tech Note
Twin Client Reference
• June, 2005
Error Message Resolution Guide
Message
Reason
Solution
Reject;
Prompt.
Advisory message.
---
Truncate;
Prompt.
Advisory message.
---
Split;
Prompt.
Advisory message.
---
Do Not Send;
Prompt.
Advisory message.
---
Always Send;
Prompt.
Advisory message.
---
Last Field Only;
Prompt.
Advisory message.
---
Internal;
Prompt.
Advisory message.
---
External;
Prompt.
Advisory message.
---
none;
Prompt.
Advisory message.
---
monarch;
Prompt.
Advisory message.
---
Twin Client Reference • June, 2005
Reference Tech Note
10-21
Error Message Resolution Guide
Message
Reason
Solution
pddumb;
Prompt.
Advisory message.
---
comtec;
Prompt.
Advisory message.
---
rascal;
Prompt.
Advisory message.
---
codewriter;
Prompt.
Advisory message.
---
comtec(S);
Prompt.
Advisory message.
---
User Name;
Prompt.
Advisory message.
---
Password;
Prompt.
Advisory message.
---
Prompt.
Advisory message.
---
Prompt.
Advisory message.
---
Prompt.
Advisory message.
---
Frequency:
Duration:
Delay:
10-22
Hz;
ms;
ms;
Reference Tech Note
Twin Client Reference
• June, 2005
Error Message Resolution Guide
Message
Reason
Solution
Select Scanner;
Prompt.
Advisory message.
---
Setup Scanner;
Prompt.
Advisory message.
---
Scan Test;
Prompt.
Advisory message.
---
Scan Operation;
Prompt.
Advisory message.
---
Laser;
Prompt.
Advisory message.
---
Contact/Pulse;
Prompt.
Advisory message.
---
Contact/No Pulse;
Prompt.
Advisory message.
---
Auto/Pulse;
Prompt.
Advisory message.
---
Auto/No Pulse;
Prompt.
Advisory message.
---
Wand Simulation;
Prompt.
Advisory message.
---
Twin Client Reference • June, 2005
Reference Tech Note
10-23
Error Message Resolution Guide
Message
Reason
Solution
VT100;
Prompt.
Advisory message.
---
VT220;
Prompt.
Advisory message.
---
HP700;
Prompt.
Advisory message.
---
SETUP;
Prompt.
Advisory message.
---
Mobile Unit IP/Radio;
Prompt.
Advisory message.
---
Host List;
Prompt.
Advisory message.
---
NULL;
Prompt.
Advisory message.
---
10-24
Reference Tech Note
Twin Client Reference
• June, 2005
">