Vertical CD Micro System

Vertical CD Micro System
Instruction Manual
Model Number: GSIMIC1002
Please read these instructions carefully and keep for future reference
For Customer Services & Spare Parts please call 01204 664 084
Opening times: Monday – Friday 9am until 5pm
WARNING
1. WARNING：Please refer the information on exterior bottom enclosure for electrical and safety
information before installing or operating the apparatus.
2. WARNING：To reduce the risk of fire or electric shock, do not expose this apparatus to rain or
moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on apparatus.
3. WARNING: The battery (battery or batteries or battery pack) shall not be exposed to excessive heat
such as sunshine, fire or the like.
4. WARNING: The mains plug is used as disconnect device, the disconnect device shall remain
readily operable.
5.
6.
Invisible laser radiation when open and interlocks defeated. Avoid exposure to beam of laser.
Correct Disposal of this product. This marking indicates that this product should not be disposed
with other household wastes throughout the EU. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable
reuse of material resources. To return your used device, please use the return and collection systems
or contact the retailer where the product was purchased. They can take this product for environmental
safe recycling.
7. No naked flame sources, such as lighted candles, should be placed on the apparatus.
8. Attention should be drawn to environmental aspects of battery disposal.
9. Use of the apparatus in moderate climates.
10. The rating and marking information are located at the bottom of the unit.
11. Excessive sound pressure from earphone and headphones can cause hearing loss.
12. The mains plug of unit should be obstructed or should be easily accessed during intended use.
13. To be completely disconnect the power input, the mains plug of apparatus shall be disconnected from the mains.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
WARNING
TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING : SHOCK HAZARD-DO NOT OPEN
EXCLAMATION POINT - within an equilateral triangle,
LIGHTNING FLASH WITH ARROWHEAD SYMBOL within an equilateral triangle, is intended to alert the
is used to indicate that a specific component shall be
user to the presence of uninsulated dangerous
replaced only by the component specified in that
voltage within the products enclosure that may be of
documentation for safety reason.
sufficient magnitude to constitude a risk of electric
shock to persons.
The following label has been affixed to the unit, listing the proper procedure for working with the laser beam:
CLASS 1 LASER PRODUCT LABEL CLASS 1 LASER PRODUCT
KLASS 1 LASER APPARAT
LUOKEN 1 LAISERLAITE
KLASSE 1 LASER PRODUKT
This label is attached to the place as illustrated to inform that the
apparatus contains a laser component.
WARNING LABEL INFORMING OF RADIATION This label is placed inside the unit. As shown in the illustration. To
warn against further measures on the unit. The equipment contains
a laser radiating laser rays according to the limit of laser product of
class 1.
E-1
SAFETY INSTRUCTIONS
1. READ INSTRUCTIONS - All the safety and operating instructions should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instruction should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating instructions should be followed.
5. WATER AND MOISTURE - The appliance should not be used near water, for example, near a bathtub, washbowl,
kitchen sink, laundrytub, swimming pool or in a wet basement.
6. VENTILATION - The appliance should be situated so that its location or position does not interfere with its proper
ventilation. Do not place on bed, sofa, rug or similar surface that may block the ventilation openings, in a built-in
installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.
7. HEAT - The appliance should be situated away from heat sources such as radiators, stoves, or other appliances
(including amplifiers) that produce heat.
8. POWER SOURCE - The appliance should be connected to power supply only of the type described in the
operating instructions or as marked on the appliance.
9. POWER CORD PROTECTION - Power supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them.
10. POWER LINES - An outdoor antenna should be located away from power lines.
11. OBJECT and LIQUID ENTRY - Care should be taken so that objects do not fall and liquids are not spilled into
the enclosure through openings.
12. ESD WARNING - The display does not function properly or no reaction to operation of any the control may due
to the electrostatic discharge. Switch off and unplug the set. Reconnect after a few seconds.
13. SERVIC,1* - The appliance should be serviced by qualified service personnel when:
a. The power-supply cord or plug has been damaged.
b. Objects have fallen into, or liquid has been spilled into the appliance enclosure.
c. The appliance has been exposed to rain.
d. The appliance has been dropped, or the enclosure damaged.
e. The appliance does not appear to operate normally.
Notes:
a. Dirty or scratched CD may cause a skipping problem. Clean or replace the CD.
b. If an error display or malfunction occurs, disconncet the AC cord and remove all the batteries. Then turn the power
back on.
BEFORE OPERATION
Notes: CONCERNING COMPACT DISCS.
Since dirty, damaged or warped discs may damage the appliance, care should be taken of the followings items:
a. Usable compact discs. Use only compact disc with the mark shown below.
b. CD compact disc only with digital audio signals.
E-2
LOCATION OF CONTROL
CD DOOR
LCD DISPLAY
REMOTE SENSOR
VOLUME +
iPOD DOCK
STANDBY
VOLUME OPEN/CLOSE
FUNCTION
PLAY / PAUSE
SKIP SKIP +
STOP
AUX IN
POWER SOURCE
AC POWER
You can power your appliance by plugging the AC power cord at the back of the appliance into a wall
AC power outlet. Check that the rated voltage of your appliance matches your local voltage.
E-3
REMOTE CONTROL
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
CLOCK
STANDBY
PRE - DOWN
TIMER
SNOOZE
SLEEP
FOLDER +
FOLDER MONO / ST.
INFO
REPEAT
SKIP -
13. STOP
14. VOLUME +
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
PLAY / PAUSE
VOLUME MENU
EQ
MENU DOWN
ENTER
MUTE
PRE-UP
INTRO
MEMORY
RANDOM
SKIP +
FUNCTION
MENU UP
2
4
6
8
10
12
17
20
1
3
5
7
9
11
13
21
22
23
24
25
26
14
15
16
18
19
27
28
BATTERY INSTALLATION
Insert 2 x “AAA” size batteries into the battery compartment. Be sure that the batteries are inserted
correctly to avoid damage to the remote control. Always remove the batteries when the remote
control will not be used for a long period of time, as this will cause leakage to the batterie s and
subsequently damage to your set.
Notes:
- Use batteries of the same type. Never use different types of batteries together.
- If the distance required between the remote control and the appliance decreases, the batteries
are exhausted. In this case replace the batteries with new one.
SENSOR WINDOW OF THE RECEIVER
- Even if the remote control is operated within the effective range, its operation may be impossible if
there are any obstacOes between the appliance and the remote control.
- If the remote control is operated near other appliances which generate infrared rays, or if other
remote control devices using infrared rays are used near the appliance, it may operate incorrectly.
E-4
RADIO OPERATION
AUTOMATIC TUNING
1. Press the “FUNCTION” button to select “TUNER” mode.
2. Press and hold the “SKIP +” or “SKIP -” button over 3 seconds to start automatic tuning process.
3. When a station is tuned in the tuning process, it will stop automatically and you can listen to your
desired station.
MANUAL TUNING
It is for selecting stations, which cannot be tuned automatically. (manual selection)
To tune a channel manually.
- Skip step 3 in the above procedures.
- In step 2, each time the “SKIP +” or “SKIP -” button is pressed momentarily (0.5 second or less),
the frequency changes by a fixed step:
FM: 0.1 MHz steps
MEMORY PRESET
1.
2.
3.
4.
Repeat step 1 to 3 in the AUTOMATIC TUNING procedures.
Press the “MEMORY” button on the remote to start the preset process.
Display will show the memory sequence number and a flashing “01”.
Press the “FOLDER +” or “FOLDER -” button on the remote to determine the preset
station number.
5. Press again the “MEMORY” button on the remote to preset your desired station.
6. Once all the stations were preset, press the “FOLDER +” or “FOLDER -” button on the remote
to listen to your desired station.
Notes:
FM can be stored up to 30 stations.
MONO / STEREO
Press the “MONO / ST.” button to achieve the best frequency.
E-5
CD / MP3 OPERATION
GENERAL OPERATION
PLAY / PAUSE
Press to start playing CD / MP3 disc.
Press again to stop playing CD / MP3 operation temporarily.
Press again to resume playback.
SKIP +
SKIP -
Press to go to the next track or back to the previous track.
Press and hold while playing until you find the point of the sound.
&
STOP
Press to stop all CD / MP3 operation.
PLAYBACK
1.
2.
3.
4.
Open the CD door and place a CD / MP3 disc with the label up in the CD compartment.
Close the CD door.
Press the “FUNCTION” button to select “CD / MP3” mode.
Focus search is performed if disc is inside.
Playback will start automatically from the first track.
5. Adjust the “VOLUME” control to the desired level.
6. Press the “PLAY / PAUSE” button when you want to stop playback temporarily.
7. Press the “STOP” button when finished.
FOLDER SELECT
Press the “FOLDER +” or “FOLDER -” button to select folder. ( Folder select function can only operate
if disc store FRQWDLQV at least 2 directories / files. )
E-6
CD / MP3 OPERATION
PROGRAM
Be sure to press the “STOP” button before use.
1. For CD disc, press the “MEMORY” button, the display will show “00 P-01”.
For MP3 disc, press the “MEMORY” button, the display will show “F00 P-01”.
2. Select desired track by using the “SKIP +” or “SKIP -” button. ( For MP3, select a desired album by
pressing “FOLDER +” or “FOLDER -” button. And press “MEMORY” button to confirm
folder number. Too will appear to select desired track by using the “SKIP +” or “SKIP -” button.)
3. Press the “MEMORY” button again to confirm desired track into the program memory.
4. Repeat step 2 and 3 to enter additional tracks into the program memory.
5. When all the desired tracks have been programmed, press the “PLAY / PAUSE” button to play the
disc in the order you have programmed.
6. Press the “STOP” button twice to terminate programmed playback.
REPEAT
Press the “REPEAT” key of remote control during playing CD / MP3 disc,
each press switches the repeat function as follows:
1 - REPEAT 1
2 - REPEAT ALBUM ( *MP3 ONLY )
3 - REPEAT ALL
4 - NORMAL PLAYBACK
REP
REP
ALBUM
REPEAT 1
REPEAT
ALBUM
REP
ALL
NORMAL
PLAYBACK
E-7
REPEAT
ALL
iPOD DOCK
GENERAL OPERATION
PLAY / PAUSE
Press to start playing tracks from the iPod.
Press again to stop playing iPod operation temporarily.
Press again to resume playback.
SKIP +
SKIP -
Press to go to the next track or back to the previous track.
Press and hold while playing until you find the point you want to play.
&
STOP
Press to stop all iPod operation.
PLAYBACK
1.
2.
3.
4.
5.
6.
Press the “FUNCTION” button to select “IPOD” mode.
When iPod is docked, the system will initialize the communication with iPod.
Power On command is sent to the iPod to wake up it.
Play command is sent afterward to auto play the iPod.
Corresponding command is sent to iPod when key is pressed.
Playback starts automatically. You can select available features (such as pOay/pause, skip track,
fast forward/backward, menu selection) during playback.
CHARGING
Charging iPod battery using the dock.
- In any mode, directly dock your iPod portable player on the cradle for charging.
* Charging IPOD / IPHONE only can work when AC power supply. When the host use battery power,
do not charging for IPOD / IPHONE.
E-8
OTHER FEATURES
EQ
Press the “EQ” button on remote control, each press switch the EQ function as follows:
1 - CLASSIC
2 - ROCK
3 - POP
4 - JAZZ
5 - FLAT (NORMAL)
Notes:
- The player not responsible for playability of MP3 in any case. Due to recording condition such as PC
performance, writing software, media ability or etc.
- For CD-RW, CD-R, it may not be played according to the type of this disc.
ID3 TAG (FOR MP3 ONLY)
1. Press once “INFO” button, ID3 text will show on display.
2. Press again to terminate ID3 mode.
Notes:
Due to various solutions, ID3 text function may not be played.
INTRO
1. Press the “INTRO” button during play disc to play each song for 15 seconds.
2. Press the “INTRO” button again to resume normal playback.
MUTE
1. Press the “MUTE” button to remove the sound during playing disc.
2. Press the “MUTE” button again to resume the sound.
E-9
OTHER FEATURES
RANDOM
1. Press the “RANDOM” button on remote control during playing disc, the applLance will select and
play a track randomly.
2. Press the “RANDOM” button again to terminate random mode.
SLEEP
1. Press the “SLEEP” button on remote control, display will show “SLEEP 90”. That means, after 90
minutes, appliance will automatically turn to standby mode.
2. Press the “SLEEP” button again to select the automatically turn off time, from 90, 80, 70, 60, 50,
40, 30, 20, 10 minutes.
3. Press the “SLEEP” button to “SLEEP 00” to canFel WKHsleep func tion.
AUX IN
Select AUX mode to listen to external audio devices connected through the 3.5mm Auxiliary Stereo
Line-In jack. Press FUNCTION to select AUX mode.
1. Use a 3.5mm Male-to-Male Stereo cable to connect any external audio device with a 3.5mm
Headphone or Ling-Out jack to the AUX IN jack on the rear panel of the stereo.
2 . Start playbDck on the external audio device. Adjust the volume on the audio device (do not set the
volume too high to avoid distortion). You may also adjust the volume on the appliance.
3. To control playback function, use the controls provided by the external audio device.
E-10
OTHER FEATURES
CLOCK SETTING
1. Press the “STANDBY” button to switch unit at standby mode.
2. Press the "CLOCK" button and hold for few seconds to entHrWKHclock set mode. The display will
show "24H" and flashing.
3. Adjust time format ( 12H / 24H ) by pressing the “SKIP +” or “SKIP -” button.
4. Press the “CLOCK” button to confirm time format, display will show “AM 12:00” or “PM 12:00” if
12H format is set or “00:00” if 24H set.
5. Adjust hour by pressing the “SKIP +” or “SKIP -” button, press the “CLOCK” button to confirm.
6. Adjust minute by pressing the “SKIP +” or “SKIP -” button, press the “CLOCK” button to confirm.
Notes:
Because clock setting is at standby mode, the display is dim.
TIMER SETTING
Timer setting must be after completed clock setting.
1. Press the “STANDBY” button to switch unit at standby mode.
2. Press the “TIMER” button to entry timer set mode.
3. The display will show “TIMER ON”, and AM 12:00 or PM 12:00 if 12H format is set or 00:00 if
24H is set.
4. Adjust hour by pressing the “SKIP +” or “SKIP -” button, press the “TIMER” button to confirm.
5. Adjust minute by pressing the “SKIP +” or “SKIP -” button, press the “TIMER” button to confirm.
6. The display will show “TIMER OFF”, and AM 12:00 or PM 12:00 if 12H format is set or 00:00 if
24H is set.
7. Adjust hour by pressing the “SKIP +” or “SKIP -” button, press the “TIMER” button to confirm.
8. Adjust minute by pressing the “SKIP +” or “SKIP -” button, press the “TIMER” button to confirm.
9. The display show input source by pressing “SKIP +” or “SKIP -” (Chose CD, i-Pod or Tuner).
Chose the input and press “TIMER” button to confirm the selection.
10.The display show volume level pressing “SKIP +” or “SKIP -” to adjust the volume level and press
“TIMER” button to confirm the selection.
11.After confirmation the unit display show “TIMER ON TIME”, “TIMER OFF TIME”, “INPUT SOURCE”
and “VOLUME LEVEL” and unit go to standby mode.
12.Press the “TIMER” button to activate timer on / off function.
13.If you want to adjust the timer, press and hold “TIMER” button for 2 sec. It go to timer setting mode.
Follow steps from 4.
14.Press and hold the “PLAY / PAUSE” button over 5 sec. to cancel all timer setting.
Follow steps from 4.
E-11
OTHER FEATURES
MENU / ENTER / MENU DN / MENU UP
MENU / ENTRE / MENU DN / MENU UP button is only for iPod / iPhone.
- When playing iPod / iPhone, press the “MENU” button to back to previous menu.
- Press the “ENTER” button to menu selection.
- Press the “MENU DN” or “MENU UP” to select next menu.
- Press the “ENTER” button again to select a desired menu or track.
- When All the desired tracks have been selected, pree the “ENTER” button to play.
E-12
For Customer Services & Spare Parts
please call 01204 664 084
Opening times: Monday – Friday
9am until 5pm
Revision 1
This symbol is known as the 'Crossed-out wheelie bin Symbol'. When this symbol is
marked on a product/batteries, it means that the product/batteries should not be disposed
of with your general household waste. Only discard electrical/electronic/battery items in
separate collection schemes, which cater for the recovery and recycling of materials
contained within. Your co-operation is vital to make sure the success of these schemes
and foR the protection of the environment. For your nearest disposal facility, visit
www.recycle-more.co.uk or ask in store for details.
We reserve the right due to possible changes to design to alter the instruction manual
without prior notice.