advertisement
E9017FD_EN.qx3 03.8.6 10:13 AM Page 1
AAA
Digital Video Disc Player
Video Cassette Recorder
FM/MW Radio Tuner
AAA
R
1
1
E9017FD_EN.qx3 03.8.6 10:13 AM Page 2
General Information
The region code for this set is 2.
Since it is usual for DVD movies to be released at different times in different regions of the world, all
2
players have region codes and discs can have an optional region code. If you load a disc of a different region code to your player, you will see the region code notice on the screen.The disc will not playback, and should be unloaded.
Manufactured under license from Dolby Laboratories.“Dolby”,
“Pro Logic” and the double-D symbol are trademarks of Dolby
Laboratories.
Manufactured under license from Digital Theater Systems, Inc. US
Pat. No. 5,451,942, 5,956,674, 5,974,380, 5,978,762 and other world-wide patents issued and pending.“DTS” and “DTS Digital
Surround” are registered trademarks of Digital Theater Systems,
Inc. Copyright 1996, 2000 Digital Theater Systems, Inc.All Rights
Reserved.
This product incorporates copyright protectiontechnology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorised by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorised by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
The System is in conformity with the EMC directive and low-voltage directive.
For Customer Use:
Read carefully the information located at the bottom of your System and enter below the Serial No. Retain this information for future reference.
Model No. MX5100VR
Serial No.
Laser safety
This unit employs a laser. Due to possible eye injury, only a qualified service person should remove the cover or attempt to service this device.
USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
LASER
Type
Wave length
Output Power
Semiconductor laser GaAlAs
655 nm (DVD) 790 nm (VCD/CD)
0.8 mW (DVD) 0.5 mW (VCD/CD)
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
KLASS 1 LASER APPARAT
CLASSE 1 PRODUIT LASER
WARNING LOCATION:
ON THE BACKPLATE OF SET
About the PBC Function of VIDEO CD
This unit conforms to ver.1.1 and ver.2.0 of VIDEO CD standard, with PBC function.
Ver.1.1 (without PBC function):You can enjoy playback picture as well as music CD.
Ver.2.0 (with PBC function):When using a VIDEO CD with PBC function, “PBC” appears on the display.
What is PBC? “PBC” stands for the PlayBack
Control.
You can play interactive software using a menu screens. Refer to instructions of VIDEO CD.
Note:
– When playing Video CDs with PBC function, some operations (e.g., select and repeat tracks) cannot be performed unless the function is cancelled temporarily
(refer to page 16).
2
Thank you for purchasing this Philips System.This Owner’s
Manual explains the basic operation of this System.
Environmental Information
All unnecessary packaging has been omitted.
Packaging has been made easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet).
Your System consists of materials which can be recycled and reused if disassembled by a specialised company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
Supplied Accessories
• Remote control • Batteries (two AA size) for remote control
• SCART cable (not available for all versions)
• MW antenna • FM antenna • Speaker set
• RF Coaxial cable • Owner’s Manual
Safety Information
• To reduce the risk of fire or electric shock, do not expose this device to rain or moisture.
• Before operating the System, check that the operating voltage indicated on the typeplate (or the voltage indication beside the voltage selector) is identical with the voltage of your local power supply. If not, please consult your dealer.
• Place the System on a flat, hard and stable surface.
• There must be sufficient room in front of the player for the disc tray to be opened.
• In cabinet, allow about 2.5cm (1 inch) of free space all around the player for adequate ventilation.
• Do not expose your player to extreme of temperature or humidity.
• If the System is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lens of the disc unit inside the System player. Should this occur, the
System would not operate normally. Leave the player on for about one hour with no disc in the System until normal playback is possible.
• The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated.
• Never spill liquid of any kind on this unit. If liquid is spilled into the unit, consult qualified service engineer.
• When the System is switched to Standby mode, it is
still consuming some power. To disconnect the system from the power supply completely, remove the
AC power plug from the wall socket.
Symbols Used in this Manual
The below symbols appear in some headings and notes with the following meanings:
DVD-V
– Description refers to playback of DVD-video discs
CD
– Description refers to playback of Audio CDs
MP3
– Description refers to playback of MP3 files
VCD
– Description refers to playback of video CDs.
Helpful Hints!
• Some DVD video discs require specific functions or allow
only limited functions during playback.
• “
” may appears on the TV screen which means that the function is not available on that specific DVD video disc. It also appears when a prohibited operation has been encountered by this unit or the disc.
E9017FD_EN.qx3 03.8.6 10:13 AM Page 3
General Information
Environmental Information. . . . . . . . . . . . . . . . . . . . . 2
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Symbols Used in this Manual . . . . . . . . . . . . . . . . . . . 2
Functional Overview
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Display Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Setting Up your System
Basic Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connecting to a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connecting to Optional Equipment
(for DVD features). . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Antenna Connections . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connecting the speaker wires to the speaker jacks . . 7
Setting up Surround Sound. . . . . . . . . . . . . . . . . . . . . 8
External Input Mode (for VCR features) . . . . . . . . . . . 8
Inserting batteries into the Remote Control . . . . . . . 8
Using the Remote Control . . . . . . . . . . . . . . . . . . . . . 8
Playable Video Cassette Tapes. . . . . . . . . . . . . . . . . . . 8
Turning on your System . . . . . . . . . . . . . . . . . . . . . . . 8
Automatic Channel Setup. . . . . . . . . . . . . . . . . . . . . . 9
Manual Channel Preset . . . . . . . . . . . . . . . . . . . . . . . . 9
Follow TV (Automatic TV channels sorting). . . . . . . . 9
Sorting and clearing TV channels manually . . . . . . . 10
Setting the language (for VCR features) . . . . . . . . . . 10
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Changing video (colour) system (for VCR features) . 10
Decoder allocation (for VCR features) . . . . . . . . . . . 10
VCR Playback
Playing cassettes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Playing back NTSC cassettes . . . . . . . . . . . . . . . . . . 11
Displaying current tape position . . . . . . . . . . . . . . . . 11
Searching for a tape position with picture
(scanning). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Still picture / slow motion . . . . . . . . . . . . . . . . . . . . . 11
Searching for tape position without picture
(forward wind and rewind) . . . . . . . . . . . . . . . . . . . . 11
Index search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Manual Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
VCR Manual Recording
General information . . . . . . . . . . . . . . . . . . . . . . . . . 12
Recording without automatic switch-off . . . . . . . . . . 12
Linking up recordings (assemble cut) . . . . . . . . . . . . 12
Selecting the recording speed (SP or LP). . . . . . . . . 12
Automatic controlled recording from a satellite receiver (RECORD LINK) . . . . . . . . . . . . . . . . . . . . 12
'Direct Record'. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Switching 'Direct Record' on or off. . . . . . . . . . . . . . 12
Direct dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Recording (From DVD To VCR). . . . . . . . . . . . . . . . . 13
Contents
Programming a Recording (TIMER)
General information . . . . . . . . . . . . . . . . . . . . . . . . . 13
Programming a recording
(with the 'S
HOW
V
IEW
® system') . . . . . . . . . . . . . . . . 13
Programming a recording
(without the S
HOW
V
IEW system). . . . . . . . . . . . . . . . 14
OTR (One Touch Recording) . . . . . . . . . . . . . . . . . . . 14
How to check, or delete a programmed recording (TIMER) . . . . . . . . . . . . . . 14
How to change a programmed recording (TIMER) . . . . . . . . . . . . . . 14
Hints for Timer Recording . . . . . . . . . . . . . . . . . . . . 14
Other Functions
Switching the status display off or on . . . . . . . . . . . . 15
Blue Background on or off . . . . . . . . . . . . . . . . . . . . 15
Clock Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Selecting the sound channel . . . . . . . . . . . . . . . . . . . 15
Digital Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Surround Sound. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Playing a Disc
Basic Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Disc Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Calling Up a Menu During Playback . . . . . . . . . . . . . 16
Step by Step Playback . . . . . . . . . . . . . . . . . . . . . . . . 16
Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Fast Forward / Reverse Search . . . . . . . . . . . . . . . . . 16
Slow Forward / Slow Reverse . . . . . . . . . . . . . . . . . . 16
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Title / Chapter Search. . . . . . . . . . . . . . . . . . . . . . . . 17
Time Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Random Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MP3/JPEG Playback . . . . . . . . . . . . . . . . . . . . . . . . . . 18
On-Screen Information . . . . . . . . . . . . . . . . . . . . . . . 18
Track Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Random Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Stereo Sound Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Subtitle Language . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Camera Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Changing the On-Screen Display . . . . . . . . . . . . . . . 19
Parental Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Marker Setup Screen. . . . . . . . . . . . . . . . . . . . . . . . . 19
DVD Setup
Audio Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Delay Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Speaker Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Display Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
FM/MW Radio
Selecting Radio Station . . . . . . . . . . . . . . . . . . . . . . . 22
Preset Radio Stations . . . . . . . . . . . . . . . . . . . . . . . . 22
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
R
S
HOW
V
IEW is a registered trademark of Gemstar Development
Corporation.
The S
HOW
V
IEW system is manufactured under licence from
Gemstar Development Corporation.
3
E9017FD_EN.qx3 03.8.6 10:13 AM Page 4
Functional Overview
Front Panel
1
STANDBY-ON
SOURCE DVD VCR TUNER
DIRECT
DUBBING PLAY STOP
18 17 16 15 14
OPEN
CLOSE
2 3 4 5
STOP/EJECT
IR
TIMER
REC
RECORD PLAY HEADPHONE VIDEO AUDIO VOL
SURR
JAZZ
POP
CLASSIC
OPTIMAL
13 12 11 10 9 8 7 6
19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
1. Disc Tray (DVD)
insert a disc here
2. OPEN/CLOSE A button (DVD) to open/close the disc tray
3. Cassette Compartment (VCR)
insert a tape here
4. STOP/EJECT C A button (VCR) when playback is stopped, press to eject the tape
5. Sound lights
Each indicator lights according to the sound effect you select by pressing the SOUND button on the remote
6. VOLUME dial
turn clockwise to increase the volume; turn counter-clockwise to decrease the volume
7. SURR light
light appears when Surround Sound is On
8. AUDIO and VIDEO in jacks
connect to AUDIO and VIDEO OUT of an audio source
9. HEADPHONE jack
connect headphones (not supplied) here
10. PLAY B button (VCR) to play a tape
11. RECORD button and light (VCR)
Press once to start recording, repeatedly to start an One
Touch Recording light appears during recording, it flashes when a recording is paused
12. TIMER REC light (VCR)
light appears when the System is in standby mode for a timer recording (also light appears during timer recording)
13. IR (Infrared) Remote Sensor (DVD,VCR,TUNER)
receive signals from remote control
14. STOP C button (DVD) to stop playback
15. PLAY B button (DVD) to start, pause or resume disc playback
16. DIRECT DUBBING button (VCR)
to play DVD disc and record its’ content to video cassette tape at the same time
17. SOURCE button and lights (DVD,VCR,TUNER)
to select DVD,VCR and TUNER mode
DVD light appears when the System in DVD mode
VCR light appears when the System in VCR mode
TUNER light appears when the System in TUNER mode
18. STANDBY-ONy button and light (DVD,VCR,
TUNER)
to switch the player to ON or OFF light appears when the System turns on.
19. DVD
Lights up when a DVD is inserted on the tray.
4
20.
(VCR)
Appears when a videotape is loaded.
21. REPEAT (DVD)
Stays on when the repeat function is on.
22. B (DVD,VCR)
Stays on when the inserted disc or cassette is being played back.
23. k (DVD,VCR)
Lights up when the inserted disc comes to a pause. (DVD)
Lights up when the playback is in a still or in a slow mode.
(VCR)
24. A-B (DVD)
Stays on when the A-B repeat function is on.
25. FM (TUNER)
Indicates an FM station
26. MW (TUNER)
Indicates an MW station
27.
(TUNER)
Indicates a stereo broadcast
28. TITLE (DVD)
Stays on when repeat title function is on.
29. Digital Display (DVD,VCR,TUNER)
Displays how long a current title or track has been played back.When a chapter or track has switched, the number of a new title, chapter or track is displayed. (DVD)
Works as a clock, or a tape counter. Also displays a channel number, and remaining time for OTR. (VCR)
Displays a current radio frequency (station number).
(TUNER)
30. CHP. (DVD)
Stays on when repeat chapter function is on.
31. TRK (DVD)
Stays on when repeat track function is on.
32. CD
Lights up when a CD is inserted on the tray.
VCD
Lights up when a VCD is inserted on the tray.
33. MHz
Indicates an FM station.
KHz
Indicates an MW station.
34. dts
Indicates DTS is available.
35. DDPL
Indicates Dolby ProLogic is available.
36. DDD
Indicates Dolby Digital is available.
Display Message
Appears after the disc tray closes if the tray is empty, if there is an error reading the disc, or if an unacceptable disc is installed.
Tray is opening or is open.
Tray is closing. This also may appear as the Player tries to load a Disc.
Disc is loading.
Lights up when a playback control is activated.
E9017FD_EN.qx3 03.8.6 10:13 AM Page 5
1
Rear Panel
2 3
RF OUT
AV2
(DECODER)
VCR
DVD/VCR
MW
AV1(TV)
AERIAL
TV ANTENNA
FM
(75
Ω)
DIGITAL
AUDIO OUT
COAXIAL
SPEAKER (4 Ω)
FL
FR
C
SL
SR
W
4 5 6 7 8 9 10 11
1. AV1 (TV) jack
connect SCART cable to a TV
2. AV2 (DECODER) jack (VCR only)
connect SCART cable from another DVD/VCR, camcoder or an audio/video source
3. MW antenna jack
connect the supplied MW antenna to the MW jack
4. S-Video Out jack (DVD only)
connect to a TV with S-Video inputs
5. RF OUT jack
use the supplied RF coaxial cable to connect to the ANTEN-
NA IN on your TV, cable box or Direct Broadcast System
6. AERIAL jack
connect to an antenna or cable
7. COAXIAL (Digital audio out) jack (DVD only)
connect to AUDIO inputs of a digital (coaxial) audio equipment
8. FM antenna jack
connect the supplied FM antenna to the FM jack
9. Fan
10. SPEAKER jacks
connect the supplied speakers using the supplied speaker wires.
11. MAINS (AC Power Cord)
connect to a standard AC outlet
Remote Control
10
11
6
7
8
9
1
2
3
4
5
STANDBY-ON
TIMER SET
SYSTEM
MENU
PROG
AUDIO/
BAND
SUBTITLE ANGLE
REC DISPLAY/STATUS/EXIT ZOOM
SKIP/
P -
TITLE
CLEAR
MODE/SYSTEM RETURN
SKIP/
P +
TUNER
DVD
DISC/VCR
MENU
VCR
OK
34
33
32
31
30
29
28
27
26
25
12
13
14
STOP PLAY
REW FF
PAUSE
1
4
7
2
5
8
+10 0
SURROUND SOUND
SLOW
3
SV / V+
6
9
REPEAT
SEARCH/INDEX
REPEAT
A-B
VOLUME
24
23
22
21
20
19
18
17
16
15
Functional Overview
1. TIMER SET
to put the System into standby mode for a timer recording
2. SYSTEM MENU
to access or remove the DVD setup menu (DVD)
PROG
to preset radio stations in Tuner mode (TUNER)
3. AUDIO/BAND
to choose audio languages or sound modes (DVD) to choose sound modes (VCR) to choose FM or MW in Tuner mode (TUNER)
4. REC I to record the TV channel selected at this moment or press repeatedly to start a One Touch Recording (VCR)
5. SKIP/P– j / SKIP/P+ i to skip chapter/tracks (DVD) to change TV channels (VCR) press and hold to search radio station or press to increase or decrease the frequency by one-tenth
(TUNER)
6. TITLE
to display title menu of a disc (DVD)
7. MODE/SYSTEM
to set up programmed or random playback (DVD, Audio CD) to change the System for matching recorded colour system
(SECAM, ME-SECAM or PAL) (VCR)
8. DVD
press to put the System in DVD mode and before using the remote control for DVD features
9. DISC/VCR MENU
to display the menu of the DVD disc or to access VCR menu
10. STOP C to stop a DVD disc playback (DVD) to stop playback, recording (VCR) to erase a preset (TUNER)
11. REW h to view DVD picture in fast reverse motion (DVD) to rewind the tape (VCR)
12. 0-9 numerical key pads/+10
select numbered items in a menu use +10 button to enter number 10 and above (DVD) to select TV channels / to enter the S
HOW
V
IEW number
(VCR) to choose a preset radio station (TUNER)
13. SURROUND
to turn Surround Sound on or off
14. SOUND
to choose a Digital Sound effect
15. VOLUME
to adjust the volume
16. REPEAT A-B
repeat a specific segment (DVD)
17. REPEAT
repeat chapter, track, title, disc (DVD)
18. SEARCH/INDEX 3 to access or remove search display (DVD) to fast forward or rewind the tape at index number (VCR)
19. SV/V+
to programme timer recording with the S
HOW
V
IEW system
(VCR)
20. SLOW
to view tape playback in slow motion (VCR)
21. FF g to view DVD picture in fast forward motion (DVD) to fast forward the tape (VCR)
22. PAUSE k pause playback temporarily / frame-by-frame playback (DVD) pause playback and recording temporarily (VCR)
23. PLAY B to start a DVD disc playback (DVD) to start a tape playback(VCR)
5
E9017FD_EN.qx3 03.8.6 10:13 AM Page 6
Functional Overview
24. { B K L
(left/right/up/down) select an item in the menu
{ B to choose a preset radio station (TUNER)
25. OK
acknowledge menu selection (DVD)
26. TUNER
press to put the System in TUNER mode and before using the remote control for TUNER features
27. VCR
press to put the System in VCR mode and before using the remote control for VCR features
28. RETURN
to return previous or remove setup menu (DVD)
29. CLEAR
to reset the setting (DVD) to reset the counter (VCR) to delete last entry/Clear programmed recording (TIMER)
(VCR)
30. ZOOM
enlarge DVD video image (DVD)
31. SUBTITLE
subtitle language selector (DVD)
32. ANGLE
select DVD camera angle (DVD)
33. STANDBY-ON y switch the System ON or OFF
34. DISPLAY/STATUS/EXIT
to access or remove the display screen during DVD or Audio
CD playback (DVD) to access or remove VCR’s on-screen status display/ to remove VCR’s menu (VCR)
Setting Up your System
Basic Connections
• Please refer to the instruction books of your TV,VCR, Stereo
System or other devices as necessary to make the best connections.
• Make one of the following connections, depending on the capabilities of your existing equipment.
The following guidelines are options for the best picture and sound quality available on your System.
Picture
1 Use SCART RGB Output (DVD/VCR(AV1 TV)) for best picture quality (for DVD features).
2 Use S-VIDEO Output for the better picture quality (for DVD features only).
3 Use SCART Composite Output for good picture quality (for
DVD and VCR features).
Sound
1 Digital audio connections provide the clearest sound. Connect the System DIGITAL AUDIO OUT (COAXIAL) to your amplifier or receiver (for DVD features only).
2 Use SCART Output (DVD/VCR(AV1 TV)) for better sound quality (for DVD and VCR features).
Warning!
– Never make or change connections with the power switched on.
– Connect the System directly to your TV, instead of eg. a
VCR, to avoid distortion because DVD video discs are copy protected.
– If you use the Euro audio/video cable, it is not necessary to use other audio cables.
Connecting to a TV
1
Disconnect the antenna or cable from your TV.
2 Connect the antenna or cable to the AERIAL of your System.
3 Connect black RF coaxial cable to the RF OUT on the rear panel of the System and to the ANTENNA IN on the TV.
4 Connect the AV1 (TV) jack on the System to the corresponding connector on the TV.
Note:
– Ensure that the “TV” indication on SCART cable is connected to the TV set and “DVD” indication on SCART cable is connected to the System.
5 Plug in the power cords of the TV and the System.
Antenna
Indoor/Outdoor
(300 ohm)
Back of DVD/VCR/TUNER
Antenna In
(on back of TV) example only
VCR
DVD/VCR
MW
S-VIDEO
OUT
RF OUT AERIAL
AV1(TV)
TV ANTENNA
FM
(75 Ω)
DIGITAL
COAXIAL
SPEAKER (4
Ω)
FL
FR
C
SL
SR
W
L/MONO
AUDIO
VIDEO
RF OUT AERIAL
OR
75
ANT
CABLE
Cable
(75 ohm)
Black RF coaxial cable
(Supplied)
6
E9017FD_EN.qx3 03.8.6 10:13 AM Page 7
If your TV is not equipped with a SCART input, you can select the following connection:
If your TV has a S-Video input connector,
1 Connect the antenna or cable to the AERIAL of your System.
2 Connect the S-Video out on the System to the S-Video in on the TV.
3 Connect the COAXIAL (Digital audio out) on the System to the Coaxial jack on the TV.
Note:
– You will still need the SCART cable for VCR features.
Setting Up your System
Antenna Connections
MW Antenna
1 Fix the antenna holder as shown.
2 Connect the supplied MW antenna to the MW jack, then position it to receive the clearest sound.
S-VIDEO
OUT
RF OUT
AV2
(DECODER)
VCR
DVD/VCR
MW
AERIAL
AV1(TV)
TV ANTENNA
FM
(75 Ω)
DIGITAL
AUDIO OUT
COAXIAL
SPEAKER (4
Ω)
FL
FR
C
SL
SR
W
RF OUT
AV2
(DECODER)
VCR
DVD/VCR
MW
AERIAL
AV1(TV)
TV ANTENNA
FM
(75
Ω)
DIGITAL
AUDIO OUT
COAXIAL
Connecting to Optional Equipment
(for DVD features)
• A digital component with a built-in MPEG 2 or Dolby
Digital
TM
decoder allows you to enjoy the surround sound while producing the effect of being in a movie theater or a concert hall.
• The player outputs the surround sound signals from the DIG-
ITAL OUT COAXIAL connector.
If your receiver has a MPEG 2 or Dolby Digital™ decoder,
1 Connect the COAXIAL DIGITAL AUDIO OUT of the System to the COAXIAL DIGITAL AUDIO IN on your receiver.
Notes:
– If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all.
– MP3 Audio is not available on the Digital Output.
– You will still need the video cable or RF coaxial cable for
VCR features.
AUDIO RECEIVER
COAXIAL DIGITAL
AUDIO IN
S-VIDEO
OUT
RF OUT
AV2
(DECODER)
VCR
DVD/VCR
AERIAL
AV1(TV)
TV ANTENNA
FM
Ω)
DIGITAL
COAXIAL
MW
SPEAKER (4 Ω)
FL
FR
C
SL
SR
W
SPEAKER (4
Ω)
FL
FR
C
SL
SR
W
FM Antenna
1 Connect the supplied FM antenna to the FM jack. Extend the
FM antenna wire and fix its end to the wall.
S-VIDEO
OUT
RF OUT
AV2
(DECODER)
VCR
DVD/VCR
MW
AV1(TV)
AERIAL
TV ANTENNA
FM
(75
DIGITAL
COAXIAL
SPEAKER (4 Ω)
FL
FR
C
SL
SR
W
Notes:
– Do not place the MW antenna on the System. Keep it as possible from the System and the speaker wires. Keep it away from the AC power cords of the System and other equipment.
– For better FM reception, connect an outdoor FM antenna (not supplied) to the ANTENNA 75 ohm jack.
Connecting the speaker wires to the speaker jacks
1
Connect the supplied speakers using the supplied speaker wires. Match the colors of the wires to the colors on the jacks. Hold down the jack tab while inserting the stripped portion of the speaker wire into the jack.Then, release the tab. Make sure you do not insert the wire too far. None of the rubber-coated wire should be clamped by the jack tab.
Front
Speaker
(left)
Subwoofer
Center Speaker
Front
Speaker
(right)
Rear Speaker
(left surround)
Rear Speaker
(right surround)
AV2
(DECODER)
VCR
DVD/VCR
MW
S-VIDEO
OUT
RF OUT AERIAL
AV1(TV)
TV ANTENNA
FM
(75 Ω)
DIGITAL
AUDIO OUT
COAXIAL
FL (Front Left - white)
FR (Front Right - red)
C (Center - green)
SL (Surround/Rear Left - blue)
SR (Surround/Rear Right - grey)
W (Subwoofer - purple)
SPEAKER (4 Ω)
FL
FR
C
SL
SR
W
7
E9017FD_EN.qx3 03.8.6 10:13 AM Page 8
Setting Up your System
Setting up Surround Sound
Connect all the speakers and set up the System properly in order to enjoy the Home Cinema experience.
1 Place the FRONT Left and Right speakers at equal distances from the TV and at a 45-degree angle from the listening position.
2 Place the CENTER speaker above or below the TV to localize the sound.
3 Place the REAR (Surround) speakers at normal listening ear level, facing each other or mounted on the wall. Use the supplied mounting brackets to mount speakers to the wall.
4 Place the Subwoofer on the floor, near the TV.
Front
Speaker
(left)
Subwoofer
Center Speaker
TV
Front
Speaker
(right)
Rear Speaker
(left surround)
VIEWING AREA
Rear Speaker
(right surround)
Notes:
– Connect the speaker wires correctly. Improper connections may short circuit the System.
– For optimal sound, use the supplied speakers.
– Do not connect more than one speaker to any pair of speaker jacks on the System.
– Do not connect speakers with an impedance lower than
6 ohms.
– Sit in your usual listening position to set up the speaker balance.
– To avoid magnetic interference, do not place the FRONT speakers too close to your TV.
– Placing the REAR (Surround) speakers farther from the listening position than the FRONT and CENTER speakers will weaken the Surround Sound effect.
– Secure all speakers to prevent accidents and improve sound quality. Use the supplied mounting brackets to mount speakers to a wall.
External Input Mode (for VCR features)
To receive the signal from an external input (decoder, satellite receiver, video camera, another VCR etc.), connect to the AV2
(DECODER) socket, and enter “002” with numerical key pads to appear “AV2” on the TV screen.
If you use the AV1 (TV) socket, enter “001” with numerical key pads to appear “AV1” on the TV screen.
If you use the front AUDIO/VIDEO input jacks, enter “003” with numerical key pads to appear “AV3” on the TV screen.
Inserting batteries into the Remote Control
1 Open the battery cover.
2 Insert batteries (AA size) with the correct polarity as indicated by the
+ and - symbols inside the battery compartment.
3 Close the cover.
8
CAUTION!
– Remove batteries if they are exhausted or not to be used for a long time.
– Do not use old and new or different types of batteries in combination.
– Batteries contain chemical substances, so they should be disposed off properly and kept away from children.
Using the Remote Control
• Direct the remote control at the remote sensor of the
System.
• Do not drop the remote control.
• Do not leave the remote control near extremely hot or humid place.
• Do not spill water or put anything wet on the remote control.
Playable Video Cassette Tapes
Philips Consume Electronics recommends that only video cassette tapes that have the VHS mark and High Quality (HQ) system is compatible with this System.This
System has an Automatic Head Cleaner.
Recording Prevention
Video cassette tapes have record tabs to ensure recordings are not erased accidentally.
1
1 To prevent recording, break off the tab with a screw-driver.
2 To allow recording, cover the hole with cellophane tape.
2
Notes:
– Use only tapes with VHS mark.
– Remove any adhesive stick-on notes from the tape before inserting into the System.
– Periodic maintenance is required to maintain your
System performance.
– Video heads will require replacement after a period of time. Only an authorised service center should perform this service.
Turning on your System
The following steps only be performed when you insert the AC
PLUG at the first time.
SELECT K L
1 Turn on the TV and select the video channel on the TV.
2 Plug in the System.
3 Press K/L repeatedly to select your desired language.
4 Press DISC/VCR MENU.
FRANÇAIS
→ ENGLISH
ESPAÑOL
DEUTSCH
ITALIANO
SVENSKA
NEDERLANDS
PUSH MENU TO CONTINUE
5 Confirm with SKIP/P+ G.
The automatic TV channel search starts.
6 'TIME' and 'DATE' will appear on
PLEASE WAIT the TV screen.
7 Check 'TIME'. If required, please change the time with numerical key pads.
START FINISH
❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚
❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚
8 Check if the displayed settings for
'DAY', 'MONTH' and 'YEAR' are correct.
9 When all information is correct, save by pressing DISPLAY/STA-
TUS/EXIT.The preparation for use is now complete.
TIME --:--
DATE --/--/--
SMART CLOCK [ON]
END=EXIT
Note:
– If the System has been completed AUTO TUNING at this procedure, this initial menu has never shown even if power failure is occured or inserted AC plug again.
E9017FD_EN.qx3 03.8.6 10:13 AM Page 9
Automatic Channel Setup
You can programme the tuner to scan only the channels that you can receive in your area.
1 Turn on the TV and select the video out channel on your TV.
2 Press VCR, then DISC/VCR MENU.
3 Press K/L to select TUNER SET UP, then press B.
4 Press K/L to select AUTO TUN-
ING, then press B.
• The System distinguishes SECAM or PAL automatically.
• The tuner scans and memorizes all the active channels in your area. After scanning, the tuner stops on the lowest memorized channel.
PLEASE WAIT
START FINISH
❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚
❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚
5 Press SKIP/P+ G / SKIP/P- H or numerical key pads to scan through channels you have received.
Manual Channel Preset
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select TUNER SET UP, then press B.
3 Press K/L to select MANUAL
TUNING, then press B.
MANUAL TUNING
4 Press K/L to select SYSTEM, then press B to appear your desired system.
5 Press K/L to select PROG., then
SYSTEM
→PROG.
CHANNEL
DECODER
SKIP press B.
6 Press K/L or numerical key pads
[ L ]
P55
055
[OFF]
[OFF]
SET=K L OR 0 – 9
END=EXIT to select your desired programme number, then press B.
• You can select programme number 01-99.
7 Press K/L to select CHANNEL, then press B.
8 Press K/L.The System tuner will begin to search up or down automatically.When a channel is found, the System will stop searching and the picture will appear on the TV Screen.
• You can select desired channel number by using numerical key pads.You must refer to the channel plan and press three digits to select the channel number. (To select channel 24, first press “0” button then press “2” and “4”).
• If this is the channel you want, press B.
• If you want to remove scrambled signals, press K/L to select
DECODER.Then, press B to select [ON].
9 Press DISPLAY/STATUS/EXIT to exit.
Notes:
– To confirm that a channel has been added, press the
SKIP/P+ G H
buttons.
– You should select the satellite channels to be received by the satellite receiver directly on the receiver itself.
Setting Up your System
Follow TV (Automatic TV channels sorting)
When the automatic channel search function is activated, the
TV channels are saved in a specific order.This may vary from the order of TV channels on the TV.
This function changes the order of TV channels saved in the
System to match that of the TV.
Make sure that the System and the TV are connected by a scart cable.
1 Press VCR, then DISC/VCR MENU.
SELECT K L CHOOSE B
2 Press K/L to select TUNER SET
UP, then press B.
3 Press K/L to select 'FOLLOW TV'
, then press B.
4 'P:01' will appear in the System display.
AUTO TUNING
MANUAL TUNING
→FOLLOW TV
MOVE
END=EXIT
I cannot switch my TV set to programme number '1'
* If you have connected additional devices to socket
AV2(DECODER), please disconnect these devices. Because of other connected devices, the TV set could switch to the programme number of the scart socket.
'NO TV SIGNAL' will appear in the TV screen.The
System is not receiving a video signal from the TV.
Check the plug on the scart cable.
Check your TV's operating instructions to see which scart socket is used for video signals.
If this does not help, it's not possible to use this function. Please read the section 'Sorting and Clearing TV channels manually'.
5 Select programme number '1' on the TV.
6 Confirm with B on the System remote control.The System compares the TV channels on the TV and the System.
If the System finds the same TV channel as on the TV, then it stores it at 'P01'.
7 Wait until the next number, e.g. 'P:02' appears in the display.
8 Select the next programme number on the TV, e.g. '2'.
9 Confirm with B.
10 Repeat steps 7 to 9 until you have assigned a programme number to all TV channels.
11 To end, press DISPLAY/STATUS/EXIT.
9
E9017FD_EN.qx3 03.8.6 10:13 AM Page 10
Setting Up your System
Sorting and clearing TV channels manually
After you have performed the automatic channel search you may not agree with the sequence in which the individual TV channels have been allocated to the programme positions (programme numbers) of the System.You can use this function to individually sort the TV channels already saved or to delete unwanted TV channels or those with poor reception.
The clock resets automatically
If you save a TV channel that transmits TXT/PDC on programme number ‘P01’, date and time will constantly be updated. As a result, time changes, i.e. daylight savings time, will be set automatically.
1 Press VCR, then DISC/VCR MENU.
MOVE
2 Press K/L to select 'TUNER SET
UP' , then press B.
3 Press K/L to select 'MOVE' , then press B.
→P01: 02
P02: 03
P03: 05
P04: 10
P05: 74
P06: 90
P07: 99
P08: 121
P09: 124
P10: 130
4 Press K/L to select the saved TV channel that you want to change.
SELECT K L CHOOSE B
END=EXIT
5 Confirm with B.
6 Move the selected channel with K/L to the programme number you want to assign.
7 Confirm with B.
8 To assign other TV channels to a programme number, repeat steps 4 to 7.
9 Confirm the assignment of the TV channel with MOVE menu.
10 To exit the MOVE menu, press DISPLAY/STATUS/EXIT.
Setting the language (for VCR features)
You have the option of setting one of the displayed languages for the on-screen menu (OSD). However, the System display will only display English text regardless of this setting.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select 'INITIAL SET
UP' , then press B.
3 Press K/L to select 'LANGUAGE',
SELECT K L then press B.
4 Select the desired language with
K
/L.
5 To end, press
DISPLAY/STATUS/EXIT.
FRANÇAIS
→ ENGLISH
ESPAÑOL
DEUTSCH
ITALIANO
SVENSKA
NEDERLANDS
END=EXIT
Setting the clock
If the display shows an incorrect time or ' --:-- ', the time and date must be reset manually.
If a TV channel that transmits TXT/PDC (teletext/PDC) is stored under programme number 'P01', time/date will automatically be taken from the TXT/PDC information. (SMART
CLOCK)
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select 'INITIAL SET UP' , then press B.
3 Press K/L to select 'CLOCK' , then press B.
4 Check the time in 'TIME'. If required, please change the time
TIME --:-with numerical key pads.
5 Check 'DAY', 'MONTH' and 'YEAR' in the same way.
6 Choose ‘SMART CLOCK’ ON or
DATE --/--/--
SMART CLOCK [ON]
OFF with B.
7 To end, press
DISPLAY/STATUS/EXIT.
END=EXIT
Changing the video (colour) system (for
VCR features)
If you playback recordings made on other video recorders or you want to record from external sources (via the scart socket), the automatic video (colour) system switch-over may lead to colour distortion. You can switch off the automatic TV system switch-over as follows.
Video (colour) systems
Other countries, other video (colour) systems:
In central Europe transmissions are broadcast in the PAL system
(Phase Alternation Line) standard. France uses SECAM (Séquentiel
à mémoire). In some countries (USA and Japan),TV viewers receive their programmes as an NTSC signal (National Television
System Committee).
1 Press MODE/SYSTEM on the remote control to select the TV
(colour) system with the least disruptions before you start recording or during playback.
Each pressing MODE/SYSTEM, the display will change cyclicaly;
AUTO, PAL, SECAM, ME-SECAM.
AUTO
2 After 5 seconds, the OSD will disappear.
How can I change back to 'Automatic Switch-over'?
Even if you change the programme number, the video (colour) system for recording will keep the setting.
If you eject the cassette, the video (colour) system for playback will switch itself back to 'AUTO' (automatic switchover).
Decoder allocation (for VCR features)
Some TV channels transmit encoded TV signals which can only be viewed with a purchased or rented decoder.You can connect such a decoder to this System.The following function will automatically activate the connected decoder for the desired
TV channel.
1 Switch the TV on. If applicable, select the programme number for the System operation.
2 Press K/L or numerical key pads to select the TV channel which you would like to allocate the decoder to.
3 Press DISC/VCR MENU.The main menu will appear.
4 Press K/L to select 'TUNER SET UP'.Then press B.
5 Press K/L to select 'MANUAL
TUNING'.Then press B.
6 Press K/L to select 'DECODER'.
7 Press B to select 'ON' (Decoder switched on).
MANUAL TUNING
SYSTEM
PROG.
CHANNEL
→DECODER
SKIP
[ L ]
P55
055
[OFF]
[OFF]
SELECT K L CHOOSE B
END=EXIT
How can I switch off the decoder?
Use B to select 'OFF' (Decoder switched off).
8 To end, press DISPLAY/STATUS/EXIT.
The decoder has now been allocated to this TV channel.
10
E9017FD_EN.qx3 03.8.6 10:13 AM Page 11
Playing cassettes
• When you select AUTO by pressing the MODE/SYSTEM button, this System will distinguish the colour system (SECAM,
PAL or ME-SECAM) automatically according to the format of recorded tape during playback.
If the picture on the TV screen is black and white, select
SECAM, ME-SECAM or PAL by using the MODE/SYSTEM button.
• Tapes recorded with the NTSC system can playback with this
System via a PAL system TV set.
Note:
– Depending on the TV, when playing back a NTSC tape on a PAL TV, the picture may roll up or down, shrink vertically and black bars may appear both at the top and bottom of the screen.
You can use this System to play back recorded VHS videocassettes.You can operate the System using the remote control or the buttons on the front of the System.
If you press PLAY, STOP, FF or REW while the set is in Standby, the power will be automatically turned on. Additionally, if a cassette was already inserted, the corresponding operation will be performed.
Your System can only record and play standard VHS cassettes.
1 Put a cassette into the cassette slot.The cassette is inserted automatically.
2 Press PLAY B to view the tape.
3 To stop the playback, press STOP C or STOP/EJECT C A on the System.
4 To eject the cassette, press STOP/EJECT C A on the System when the System stops the playback.
DIGITAL STUDIO PICTURE CONTROL
Philips has developed a system which produces the best possible playback quality. For old and often-used video cassettes, this system reduces interference. For new or high quality cassettes, it emphasises the details.
Picture/ sound quality is poor
When playing rental videos or older, poorer quality cassettes, it may not be possible to completely filter out picture and sound interference.This is not a fault in your machine. Read the section
'Manual Tracking'.
Do I need to change the playback speed when playing back LP recordings?
During playback, the correct speed will automatically be selected.
For more information, please read the section 'Selecting the recording speed (SP or LP)' in the chapter 'VCR Manual
Recording'.
Playing back NTSC cassettes
This System can also play back cassettes that have been recorded in SP [Standard Play] or SLP [Super Long Play] mode in the NTSC standard (for example, American cassettes).
However, this only works on PAL-television sets that are suitable for a picture frequency of 60Hz.
Displaying current tape position
The following information is displayed on the screen: e.g.:
0:02:45 shows the counter in hours, minutes and seconds.
SP/LP: will show the recorded speed of your cassette
'REM 0:06': will show the actual amount of playing/recording time left on the tape in hours and minutes.
When you play an NTSC cassette, the System will show 'REM -
:--'.
How can I set the counter to '0:00:00'?
You can set the counter to '0:00:00' with CLEAR.
When you put a cassette in the System, the counter will automatically reset to '0:00:00'.
VCR Playback
The counter does not move
This occurs when there are no recordings on a portion of a tape.
This is not a fault in your System.
The screen shows '-0:01:20'
If you rewind a cassette from the tape position '0:00:00', the counter will show for instance, '-0:01:20' (the cassette was rewound to 1 minute and 20 seconds before '0:00:00').
'-:--' is displayed in the 'REM' counter
This counter will automatically recognise the length of the tape. In addition, when you put in a cassette the System must first calculate the time played.Therefore, '-:--' appears first and only after the tape has been running for a few seconds, the correct playing time will be shown.
Searching for a tape position with picture
(scanning)
1 While a cassette is playing, press REWh (rewind) or FF g
(forward) one or more times.
2 Press PLAY B to resume playback.
Still picture / slow motion
1 During playback, press PAUSE k to stop the tape and display a still picture.
2 During playback, press SLOW to play the tape in slow motion.
3 Press PLAY B to resume playback.
Scanning and still/slow motion interferes with the picture quality.The sound is switched off.This is not a fault in your System.
Searching for tape position without picture
(forward wind and rewind)
1 Stop the tape with STOP C.
2 Press REW h (rewind) or FF g (forward).
3 To stop the tape, press STOP C.
Index search
Every time a tape is recorded an index marking is written on the tape.
These marked positions can be found again quickly and easily later.
1 To search for the previous marking, press SEARCH/INDEX 3 and then REW h.
2 For the next marking, press SEARCH/INDEX 3 and then
FF g.
3 As soon as the System finds this marking, it automatically switches to playback.
Manual Tracking
To manually adjust the tracking during playback and slow motion playback, press SKIP/P+G or SKIP/P-H.
Tracking will return to Automatic Tracking Adjustment when you press STOP C, insert a tape, or press PLAY B.
To remove vertical jitter in a Still picture, press SKIP/P+G or
SKIP/P-H.
11
E9017FD_EN.qx3 03.8.6 10:13 AM Page 12
VCR Manual Recording
General information
Use 'Manual Recording' to make a spontaneous recording
(for example, a programme currently being shown).
If you want to start and stop a recording manually, read the section 'Recording without automatic switch-off'.
Read the section 'Direct Record' if you want to record a programme currently being shown.
Read the section 'Automatic controlled recording from a
satellite receiver (RECORD LINK)', if you want a recording to be controlled automatically by a satellite receiver.
Recording without automatic switch-off
1 Insert a cassette.
2 Use SKIP/P+ G / SKIP/P- H to select the programme number you want to record, for example, 'P01'.
3 To start recording, press REC I.
4 Stop recording with STOP C.
Linking up recordings (assemble cut)
When you add a further recording to a cassette, which already has a recording on it, a short blank (flicker) can appear between the old and the new recording or the picture itself can flicker.
To help reduce these from occurring, proceed as follows:
1 Find the tape position of the old recording where you want to insert the new recording.
2 Look at the last minute of the old recording (playback).
3 Press PAUSE k at the tape position where the new recording is to go and press REC I.
4 Now start recording as usual by pressing REC I on the remote control.
5 Stop recording with STOP C.
Selecting the recording speed (SP or LP)
LP allows to double the recording duration on tape (for example six hours instead of three hours on an E180 cassette).
1 Switch on the TV set. If required, select the programme number for the System.
SELECT K L CHOOSE B
2 Press DISC/VCR MENU.The main menu will appear.
3 Select 'RECORD SETUP' using
→RECORD SPEED [SP]
DIRECT RECORD [OFF]
RECORD LINK [OFF]
K
/L and confirm with B.
4 Select 'RECORD SPEED' using K/L.
5 Select the required recording speed with B.
END=EXIT
'SP'/'LP' /'AUTO'
'SP': StandardPlay (normal recording speed) offers the usual firstclass picture quality.
'LP': LongPlay (half recording speed, double recording time). 6 hours can be recorded on a 3-hour cassette (E180) with a somewhat reduced picture quality.
'AUTO': AUTOmatic Long Play. If there is not enough space on the tape to record a programmed recording in standard speed, the recording is automatically done in 'LP'
(Longplay). Otherwise, the recording speed will be 'SP'
(Standardplay).
6 To end, press DISPLAY/STATUS/EXIT.
Automatic controlled recording from a satellite receiver (RECORD LINK)
This function automatically starts recording on the switched-off
System when a video signal is recognised through the connected scart cable. If your satellite receiver has a programming function, the recording will start automatically (as long as the satellite receiver is switched on).
1 Use a scart cable to connect scart socket AV2(DECODER) on the System to the corresponding scart socket on the satellite receiver.
2 Switch on the TV. If required, select the programme number for the System.
3 Press DISC/VCR MENU.The main menu will appear.
4 Select 'RECORD SET UP' with K/L and confirm with B.
5 Select 'RECORD LINK' with K/L.
SELECT K L CHOOSE B
6 Select function 'ON' with B.
7 To end, press
DISPLAY/STATUS/EXIT.
8 Insert a cassette.
RECORD SPEED [SP]
DIRECT RECORD [OFF]
→RECORD LINK
[OFF]
9 Programme the satellite receiver with the required information (programme number of the TV channel, start time, end time).
END=EXIT
If necessary, please see the operating instructions for your satellite receiver.
10 Press TIMER SET.
The System is now ready to record.The beginning and end of the recording is controlled via scart socket AV2(DECODER).
'Direct Record'
With Direct Record, you can record the right TV channel in seconds even if your System is switched off. If the recording is started manually, the System uses the current TV channel set on the TV.You will find more information on how to switch
'Direct Record' on or off in the next section. Make sure that your System socket AV1(TV) and the TV are connected by a scart cable.
1 On the TV, select the programme number you want make the recording from.
2 Press REC I with the System switched off.
3 Stop recording with STOP C.
How does Direct Record work?
The System compares the TV channel selected on the TV set with its stored TV channels via the scart cable. If the same TV channel is found, it switches the System to the corresponding programme number and starts recording. Please do not change the TV channel on the TV set during the search so as not to affect the process.
Switching 'Direct Record' on or off
1 Switch on the TV. If required, select the programme number for the System.
2 Press DISC/VCR MENU.The main menu will appear.
3 Select 'RECORD SET UP' with
K
/L and confirm with B.
4 In 'DIRECT RECORD', select 'OFF'
(Direct Record off) or 'ON'
SELECT K L CHOOSE B
RECORD SPEED [SP]
→DIRECT RECORD [OFF]
RECORD LINK [OFF]
(Direct Record on) with B.
5 To end, press
DISPLAY/STATUS/EXIT.
6 Press STANDBY-ONy.
END=EXIT
12
E9017FD_EN.qx3 03.8.6 10:13 AM Page 13
VCR Manual Recording
Direct dubbing
Follow the steps below to copy a DVD or video disc to a videotape.This will be possible only if the DVD is not copy protected.
1 Put a videotape in the cassette compartment. Make sure the tape’s record tab is intact and the tape is long enough to record the disc.
2 Press VCR.
3 Select the recording speed.
Details are at “Selecting the recording speed (SP or LP)”.
4 Put the DVD you want to copy in the disc tray.
5 Press DVD.
6 Press PLAY B.While disc is playing, press PAUSE k at the point you wish to start recording.
7 Press DIRECT DUBBING to record.
To pause the recording.
Press PAUSE k.
To resume recording.
Press PAUSE k again.
To stop the recording.
Press STOP C.
Programming a Recording (TIMER)
General information
Use a TIMER programming to automatically start and stop a recording at a later time or date.The System will switch to the right programme number and begin recording at the correct time.With this System, you can pre-programme up to eight recordings within a period of one year.To make a programmed recording, your System needs to know:
* the date you want to make the recording
* the programme number of the TV channel
* the start and stop time of the recording
* VPS or PDC on or off
This information is saved in a TIMER block.
What is 'VPS/PDC'?
'VPS' (Video Programming System)/ 'PDC' (Programme Delivery
Control) are used to control the start and duration of TV channel recordings. If a TV programme starts earlier or ends later than scheduled, the System will turn on and off at the correct time.
What do I need to know about 'VPS/PDC'?
Usually the VPS or PDC time is the same as the start time. But if your TV guide shows a VPS or PDC time which is different from the programme’s scheduled start time, e.g. 20.10 (VPS/PDC
20.14), you must enter the VPS/PDC time exact to the minute. If you want a start time different from the VPS/PDC time, you must switch VPS/PDC off.
Recording(From DVD To VCR)
1 Insert a DVD without copyright protection in the tray.
2 Insert a video cassette tape with its erase prevention tab in place.
3 Select the recording speed.
Details are at “Selecting the recording speed (SP or LP)”.
4 Enter “004” with numerical key pads to appear “DISC” on the
TV screen.
5 Press REC I.
6 Change to DVD operation mode.
7 Press DVD, then PLAY B to begin the playback of a DVD.
8 Press VCR, then STOP C to stop recording.
Programming a recording
(with the 'S
HOW
V
IEW
® system')
R
You no longer need to tediously enter the date, programme number, start and end time. All the information needed for programming is contained in the S
HOW
V
IEW
-programming number.
You can find this S
HOW
V
IEW number in most TV listing magazines written next to the concerned programme.
1 Press SV/V+.
2 Enter the entire S
HOW
V
IEW num-
ShowView system
ShowView No.
ber.This number is up to 9 digits long and can be found next to the 12345 – – – – start time of the TV programme in your TV listing magazine. [e.g: 1-
234-5 or 1 234 5]
If you make a mistake, you can clear your input with CLEAR.
3 Press SV/V+.
4 Select ONCE, DAILY or WEEKLY recording with K/L.Then press B.
SET=SV/V+
CORRECT=CLEAR
END=EXIT
ShowView system
→ONCE
DAILY
WEEKLY
SELECT K L CHOOSE B
END=EXIT
Selecting once/daily/weekly recordings
Using K/L, select from the following options:
'ONCE': Recording once
'DAILY': Repeated daily recordings (Monday to Friday)
'WEEKLY': Repeated weekly recordings (every week on the same day)
'- -' appears at PROG. .
* The programme number of the TV channel has not yet been assigned to the S
HOW
V
IEW number. Using the numerical key pads, select the corresponding programme number (name) of the TV channel.
The following message appears on the screen:'ERROR'
* The entered S
HOW
V
IEW number is incorrect. Correct your input or end with DISPLAY/STATUS/EXIT.
* Check the time/date (see chapter 'Installing your video', section
'Setting the time and date').
* A daily recording was entered for the wrong day. Daily programming can only be used for recordings to be made from
Monday to Friday.
The following message appears on the screen:'TIMER
NOT COMPLETED'
* The channel is wrong.
13
E9017FD_EN.qx3 03.8.6 10:13 AM Page 14
Programming a Recording (TIMER)
5 The decoded data appears after confirmation.You can go back to change the data. Select the corresponding input field using
B or CLEAR. Change the data with numerical key pads.
6 When all inputs are correct, press DISPLAY/STATUS/EXIT.The
programming information is stored in a Timer block.
Switching on 'VPS/PDC' in the 'START' input field
Select 'VPS/PDC' using B or CLEAR. Press '1' to switch off
'VPS/PDC' or press '2' to switch on 'VPS/PDC'.
7 Insert a cassette with an intact security tab (unprotected).
8 Press TIMER SET.
'TIMER REC' will light up on the System.
How to check, or delete a programmed recording (TIMER)
1
Press VCR, then DISC/VCR MENU.
2 Press K/L to select 'TIMER'.Then
press B.
3 Press K/L to select 'TIMER LIST' , then press B.
SELECT K L CHOOSE B
ONCE
DAILY
WEEKLY
→TIMER LIST
4 Select timer block with B.
5 To cancel the recording, press
CLEAR.
6 To end, press DISPLAY/STATUS/EXIT.
END=EXIT
7 Press TIMER SET.
Programming a recording
(without the S
HOW
V
IEW
system)
1 Press VCR, then DISC/VCR MENU.
2 Select 'TIMER' with K/L.Then
press B.
3 Select ONCE, DAILY or WEEKLY recording with K/L.Then press B.
If all Timer blocks are in use, ‘FULL’ will appear on the OSD.
4 Select the desired Timer block with
SELECT K L CHOOSE B
→ONCE
DAILY
WEEKLY
TIMER LIST
END=EXIT numerical key pads. (The flashing number indicates an empty TIMER block.)
Selecting once/daily/weekly recordings
Using K/L, select from the following options:
'ONCE': Recording once
'DAILY': Repeated daily recordings (Monday to Friday)
'WEEKLY': Repeated weekly recordings (every week on the same day)
5 Enter the Start time (START) End time (STOP), Programme number (PROG.),VPS/PDC information and the Date with numerical key pads.
Programme numbers of the ' AV1 ' , ' AV2 ' and ' AV3' scart socket
You can also programme recordings from external sources via scart socket AV1(TV), AV2 (DECODER) or AV3(FRONT).
6 When all inputs are correct, press DISPLAY/STATUS/EXIT.The
programming information is stored in a TIMER block.
7 Insert a cassette with an intact security tab (unprotected).
8 Press TIMER SET.
How to change a programmed recording
(TIMER)
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select 'TIMER' ,then press B.
3 Press K/L to select ONCE, DAILY, or WEEKLY recording with K/L ,
ONCE then press B.
4 Select a TIMER block with numerical key pads. (The flashing number indicates an empty TIMER block.)
TIMER - 1 2 3 4 5 6 7 8 -
5 Press CLEAR to delete information and input correct information with numerical key pads.
6 To end, press DISPLAY/STATUS/EXIT.
7 Press TIMER SET.
SELECT TIMER NUMBER
END=EXIT
Hints for Timer Recording
• If there is a power failure or the System is unplugged for more than 1 minute, the clock setting and all timer settings will be lost.
• If a tape ends during TIMER RECORDING, the System will stop, eject the tape, and switch to the DVD mode automatically as the TIMER REC light blinks. (If the DVD power is off, the System will become the STANDBY status).
• If a tape is not in the System or does not have a record tab, the TIMER REC light flashes and timer recording will not operate. Please insert a recordable tape.
• When timer recordings are set, the TIMER REC light will come on.To use the System as usual until the time for the recording, press TIMER SET so that the TIMER REC light disappears. Press the System to choose VCR, DVD or TUNER modes, then continue with the other features as described in this manual.
'PRESS TIMER SET BUTTON FOR TIMER RECORDING' appears on the screen
* Press TIMER SET on several minutes before the start of a programmed recording.
Error message: 'FULL'
• If this error message appears after you select 'ONCE', 'DAILY', or 'WEEK-
LY' on TIMER menu and press B, then all TIMER blocks are already programmed. No more recordings can be programmed. If you want to clear or check a programmed recording (TIMER block),select the programme number on TIMER LIST menu and press CLEAR.
OTR (One Touch Recording)
This function enables you to set a recording length simply by pressing RECORD on the System.
1 Follow steps 1 to 2 in “Recording without automatic switchoff” section.
2 Press RECORD on the System repeatedly until the desired recording length appears.
0:00 0:30 1:00...
7:30 8:00
REC (Normal recording)
• Recording stops when 0:00 is reached.
To check time remaining during an OTR
Press DISPLAY/STATUS/EXIT.
To change the recording length during an OTR
Press RECORD until the desired length appears.
To stop an OTR before recording is finished
Press STOP C .
To cancel the OTR but continue recording
Press RECORD repeatedly until “REC” appears in the upper left corner of the TV screen.
14
E9017FD_EN.qx3 03.8.6 10:13 AM Page 15
Switching the status display off or on
Along with the on screen menu, the status display also displays information on the current operating status (counter, playback, recording,TV channel, etc.) on the TV screen.You can switch off the information about the operating status so that the status display is not recorded when copying videocassettes.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select 'VCR SET UP'
, then press B.
3 Press K/L to select 'STATUS DIS-
SELECT K L CHOOSE B
→STATUS DISPLAY
[ON]
BLUE BACKGROUND [ON]
CLOCK DISPLAY [ON]
PLAY' , then press B.
4 Press K/L to select 'ON' or 'OFF'
, then press B.
5 To end, press
DISPLAY/STATUS/EXIT.
END=EXIT
Which settings can I choose?
'ON': Shows the status display for a few seconds only.
'OFF': Switches off the status display.
Blue Background on or off
If you want the TV screen to be solid blue when a weak signal is received, set BLUE BACKGROUND to ‘ON’.The screen will be blue and the sound will be muted. Or, if you want to receive the weak signal, set BLUE BACKGROUND to ‘OFF’.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select 'VCR SET UP'
, then press B.
SELECT K L CHOOSE B
3 Press K/L to select 'BLUE BACK-
GROUND' , then press B.
STATUS DISPLAY [ON]
→BLUE BACKGROUND [ON]
CLOCK DISPLAY [ON]
4 Select 'OFF' (no blue background) or 'ON' (blue background on) with
B .
5 To end, press
DISPLAY/STATUS/EXIT.
END=EXIT
Clock Display
This function allows you to switch the System display off. It is useful in case you feel disturbed by the display-brightness while watching TV in a dark room. It also reduces the power consumption.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select 'VCR SET UP'
, then press B.
3 Press K/L to select 'CLOCK DIS-
SELECT K L CHOOSE B
STATUS DISPLAY [ON]
BLUE BACKGROUND [ON]
→CLOCK DISPLAY
[ON]
PLAY' , then press B.
4 Select 'OFF' (no clock display) or
'ON' (clock display on) with B.
5 To end, press
DISPLAY/STATUS/EXIT.
END=EXIT
Selecting the sound channel
• During reception of bilingual broadcasts:
You can select the desired sound channel during playback or while receiving TV channels via the System.This
allows you to select a desired language for multi-language transmissions.
1 Press AUDIO/BAND.
This will show the current sound setting.
2 Press AUDIO/BAND until the desired setting appears in the display.
Mode
MAIN
SUB
MAIN
SUB
L
R
L
R
L
R
Main Audio
Main Audio
Sub Audio
Sub Audio
Main Audio
Sub Audio
• Reception of stereo broadcasts:
Mode
Stereo
L
R
Monaural
L
R
L
R
L
R
L
R
AUDIO OUTPUT
AUDIO OUTPUT
L Audio
R Audio
L Audio
L Audio
R Audio
R Audio
L + R Audio
L + R Audio
Display on the TV screen
MAIN
SUB
MAIN
SUB
Display on the TV screen
STEREO
LEFT
RIGHT
NONE
Other Functions
• During playback of the recorded tape in Hi-Fi mode:
Mode AUDIO OUTPUT
Display on the TV screen
Stereo
L
R
Monaural
L
R
L
R
L
R
L
R
Hi Fi L Audio
Hi Fi R Audio
Hi Fi L Audio
Hi Fi L Audio
Hi Fi R Audio
Hi Fi R Audio
Normal Audio
Normal Audio
STEREO
LEFT
RIGHT
MONO
MIX
L
R
Hi Fi L Audio
+ Normal Audio
Hi Fi R Audio
+ Normal Audio
MIXED
Digital Sound
Digital Sound lets you enjoy special sound effects that have preset equalizer settings, providing the best music reproduction.The default setting of the System is OPTIMAL.
1 Press SOUND repeatedly to select OPTIMAL, CLASSIC, POP, or JAZZ.
The selected Digital Sound light will appear on the front of the
System.
Surround Sound
For proper Surround Sound, connect the speakers and
Subwoofer correctly.The Center and Rear (Surround) speakers only operate when Surround is On.The Discs or TV programs must be recorded or broadcast in Surround Sound.
1 Press SURROUND to set Surround to On or Off.
When Surround is On, the SURR (Surround) light will appear on the front of the System.When Surround is Off, the SURR
(Surround) light will be off.
Programs broadcast in Stereo will produce some surround sound effects when played in a surround mode. However, non-
Stereo programs will not have any sound at the Rear
(Surround) speakers.
The following Surround Sound modes may be broadcast by
DVDs or TV stations.You cannot alter these Surround Sound options at the System.
Matrix: Delivers sound through 5.1 Channels.You will have sound at all five speakers (Front Left and Right, Center, and
Rear (Surround) Left and Right).
Dolby Digital: Dolby Digital is a high-quality audio compression technology first used in movies.This technology has since been adopted for use in Consumer Electronic products and allows you to enjoy the same type of sound in your home.Your
player has a built-in Dolby Digital decoder so you can enjoy
DVDs that include a Dolby Digital soundtrack.
You can identify DVDs and equipment that contain Dolby
Digital by looking for the following logo:
Dolby Pro Logic: A two-channnel analog format that proivides sound through four speakers (Front Left and Right, Center, and a single Rear (Surround)) when using a Dolby ProLogic Decoder. It is compatible with a Stereo, but you will only have two-channel sound (left and right) at the Stereo.
DTS (Digital Theater System): Developed by Digital
Theater Systems, Inc., of the United States. Sound is compressed to reduce its recording size. Since the compression level is less than Dolby Digital, the quantity of data is greater when decoded, providing clarity and depth in the sound.The
sound has a wider dynamic range and higher resolution.
Note:
- Surround Sound is not available when you are using headphones.The SURROUND light will turn off.
15
E9017FD_EN.qx3 03.8.6 10:13 AM Page 16
Playing a Disc
Basic Playback
DVD-V
CD VCD
Getting Started
Turn on the power of the TV, amplifier and any other components which are connected to the DVD system.
Make sure the TV and audio receiver (commercially available) are set to the correct channel.
1 Press STANDBY-ONy.
2 Press DVD, then OPEN/CLOSE A to open disc loading tray.
3 Place the chosen disc in the tray, with the label facing up.
4 Press PLAY B .
• The tray will close automatically, and
POW
playback will then start from the first chapter or track of the disc. If the playback does not start automatically, press
PLAY B.
• When you playback the DVD which a title menu is recorded, it may appear on the screen. In this case, refer to “Title
Menu”.
5 Press STOP C to stop playback.
Notes:
- A “prohibited icon” may appear at the top-right on the
TV screen during operation, warning that a prohibited operation has been encountered by the DVD system or the disc.
- With DVDs that use some titles for playback program signals, playback may start from the second title, or it may skip these titles.
- During the playback of two layered disc, pictures may stop for a moment.This happens when the 1st layer switches to the 2nd layer.This is not a malfunction.
Cancelling and Calling Back PBC Function
1 Insert a Video CD.
• Playback will start automatically.
2 Press STOP C.
VCD
3 Press numerical key pads to enter the desired track number.
• PBC function is now cancelled and the playback of the Video
CD will start.
4 To call back PBC function, press STOP C twice, and then press
PLAY B .
• Title menu will appear on the display.
General Features
DVD or video CDs may contain menus to navigate the disc and access special features. Press the appropriate numerical key pads or use Arrow ( L / K / B / s ) to highlight your selection in the DVD main menu and press OK to confirm.
Note:
- Unless stated, all operations described are based on remote control use. Some operations can be carried out using the menu bar on the TV screen.
Pause
DVD-V
CD
VCD
1 During playback, press PAUSE k.
• Playback will pause and sound will be muted.
2 To continue playback, press PLAY B .
Disc Menus
DVD-V
1 Press DVD, then DISC/VCR MENU.
• The DVD main menu will appear.
2 If the feature is not available,
TV screen.
symbol may appear on the
3 If disc menu is available on the disc, audio language, subtitle options, chapters for the title and other options will appear for selection.
4 Press Arrow ( L / K / B / s ) to select an item, and OK to confirm selection.
16
Title Menu
DVD-V
1 Press DVD, then TITLE.
• The title menu will appear.
2 If the feature is not available, symbol may appear on the
TV screen.
3 Press Arrow ( L / K / B / s ) to select an item, and OK to confirm selection.
• Playback will begin at the selected Title.
VCD
1 The title menu will appear.
2 Press numerical key pads to select the menu.
• Playback will start.
Calling Up a Menu During Playback
DVD-V
• Press DISC/VCR MENU to call up the DVD main menu.
• Press TITLE to call up the title menu.
Note:
- Contents of menus and corresponding menu operations may vary between discs. Refer to the manual accompanying the disc for details.
Step by Step Playback
DVD-V
VCD
1 During playback, press PAUSE k.
• Playback will pause and sound will be muted.
2 The disc goes forward by one frame each time PAUSE k is pressed.
3 To exit step by step playback, press PLAY B.
Resume
DVD-V
CD
VCD
1 During playback, press STOP C.
• Resume message will appear on the TV screen.
2 Press PLAY B, playback will resume from the point at which playback was stopped.
• To cancel resume, press STOP C twice.
Notes:
- The resume information stays on even when the power is turned off.
- Some Video CDs with PBC function resume playback from the beginning of the track.
Fast Forward / Reverse Search
CD
DVD-V
MP3 VCD
1 During playback, press FF g or REW h repeatedly to select the required forward or reverse speed: x2, x8, x50, x100.
• For video CDs, the speed is fixed at x2, x8, x30.
• For audio CDs, the speed is fixed at x16.
• For MP3, the speed is fixed at x8.
2 To return to normal playback, press PLAY B.
Slow Forward / Slow Reverse
DVD-V
VCD
1 During playback, press PAUSE k.
2 Press FF g or REW h .
• Slow motion playback will begin and sound will be muted.
3 Press FF g or REW h repeatedly to select the required speed: 1/16, 1/8, 1/2 of the normal playback.
4 To return to normal playback, press PLAY B.
Note:
- Slow Reverse is not available on video CDs.
E9017FD_EN.qx3 03.8.6 10:13 AM Page 17
Zoom
DVD-V
VCD
The Zoom function allows you to enlarge the video image and to pan through the enlarged image.
1 Press ZOOM during playback.
• Playback will continue.
2 Press ZOOM repeatedly to select the required zoom factor: x2, x4 or OFF.
3 Use Arrow ( L / K / B / s )to move the zoomed picture across the screen.
4 To exit zoom mode, press ZOOM to OFF.
Notes:
- Zooming function does not work while disc menu is shown.
- x4 zoom is not available on some discs.
- only x2 zoom is available on video CDs.
Playing a Disc
Repeat
• REPEAT are available only during playback.
Repeat Title / Chapter
DVD-V
To activate the repeat function, press REPEAT during playback.
• The repeat mode changes as described below every time you press the button.
OFF
(repeat off)
CHAPTER
(current chapter repeat)
TITLE
(current title repeat)
Track
CD
VCD
There are three ways to begin playback on an Audio CD at a specific Track.
Using the Numerical key pads
1 Press numerical key pads to enter the desired Track number.
• Playback will start at the selected track.
• For single digit tracks (1-9), press a single number (eg. track 3, press 3).
• To play track 26, press +10, 2, 6 on the numerical key pads.
Using the SEARCH MODE
1 Press SEARCH/INDEX3.
• The track search display appears.
2 Within 30 seconds, select a desired track number using numerical key pads. For single digits press “0” first.
• Playback will start at the selected track.
Using the SKIP/P- H ,SKIP/P+ G
During playback, press SKIP/P+ G to move to the next track.
Press it repeatedly to skip subsequent tracks. Press SKIP/P- H to go back to the beginning of the current track. Press it repeatedly to go to the previous tracks.
• Track number will appear briefly on the DVD system display panel.
• If SKIP/P+ G is pressed while the playback is paused, the playback will be paused again after skipping to the next track.
Note:
- SKIP/P- H , SKIP/P+ G are not available when play-
back is stopped.
Title / Chapter Search
1 Press SEARCH/INDEX 3once for the Chapter search, twice for the Title search during playback.
2 Enter the desired chapter/title number using numerical key pads.
DVD-V
/2
Notes:
- Repeat Title/Chapter is not available with some scenes.
- The REPEAT setting will be cleared when moving to other title or chapter.
Repeat Track
CD VCD
To activate the repeat function, press REPEAT during playback.
• The repeat mode changes as described below every time you press the button.
OFF
(repeat off)
TRACK
(current track repeat)
ALL
(entire disc repeat)
MP3
OFF
(repeat off)
TRACK
(current track repeat)
GROUP
(entire group repeat)
ALL
(entire disc repeat)
Notes:
- The REPEAT setting will be cleared when moving to other track.
- Repeat playback does not function during repeat A-B playback.
Repeat at A-B
DVD-V
CD
VCD
1 Press REPEAT A-B at your chosen starting point.
• A- appears briefly on the TV screen.
2 Press REPEAT A-B again at your chosen end point.
• A-B appears briefly on the TV screen, and the repeat sequence begins.
3 To exit the sequence, press REPEAT A-B.
Notes:
- The repeat A-B section can only be set within the current title (for DVDs), or current track (for audio CDs).
- Repeat A-B is not available with some scenes in DVD.
- To cancel the A point which was set, press CLEAR.
- Repeat A-B playback does not function during title, chapter, track or all repeat playback.
Time Search
DVD-V CD
VCD
1 During playback, press SEARCH/INDEX 3 three times
(CD/VCD: twice) to display the Time Search on the TV screen.
2 Within 30 seconds, enter a desired disc time using numerical key pads.
• Playback will start at the specified time.
3 Press CLEAR to erase the incorrect input.
17
E9017FD_EN.qx3 03.8.6 10:13 AM Page 18
Playing a Disc
Program
CD
You may determine the order in which tracks will play.
1 In stop mode press MODE/SYSTEM.
• The PROGRAM screen will appear.
2 Press
▲ or ▼ to select a track, then press OK.
• Press CLEAR to erase the most recently entered program.
3 Press PLAY B to play the pro-
T
T
T
T
T
T
T
OK grammed tracks.
Notes:
T
- While the program is being
played back, the STOP C works as follows.
TOTAL
T
- Press STOP C once and then PLAY B again, playback will
restart from the point where STOP C was pressed.
(Program continued)
- Press STOP C twice and then PLAY B again, playback will
restart from the track in the usual way. (Program cleared)
- Up to 99 programs can be entered.
- If you like to repeat the current track in the program, press
REPEAT repeatedly until TRACK appears during playback. If you like to repeat the entire program press
REPEAT repeatedly until ALL appears during playback.
Random Playback
CD
This shuffles the playing order of tracks instead of playback in the sequence.
1 In stop mode, press
MODE/SYSTEM twice.
• RANDOM screen appears.
2 Press PLAY B to start random playback.
Note:
RANDOM
PLAY
CD [AUDIO] TOTAL 0:45:55
RANDOM PROGRAM
-- no indication --
- If you like to repeat the current track in the random selection, press REPEAT repeatedly until TRACK appears during playback. If you like to repeat the entire random selection press REPEAT repeatedly until ALL appears during playback.
MP3/JPEG Playback
MP3
When a CD with MP3 or JPEG files is inserted in the DVD system, the MP3 or JPEG menu will appear on the TV screen, and number of tracks is displayed on the front panel.
1 In stop mode, press K or L to select the desired group, MP3 track or JPEG file.
• If a group is selected, press
PLAY B or OK to go on to
FOLDER
MP3
JPEG the track selection screen.
Press K or L to choose a track, then press PLAY B or
OK.
OK
PLAY
• If a track is selected, press PLAY B or OK to start playing tracks. Starting from the one you’ve just chosen the subsequent tracks will be played.
• Choose FIRST PLAY to start playback from the beginning of the listed tracks.
• Press TITLE to return to the first item.
2 Press STOP C to stop playback.
Notes:
- Folders are known as Groups; files are known as Tracks.
- MP3 files are accompanied by
3
icon.
- JPEG files are accompanied by icon.
- Maximum of 255 folders can be recognized.
- Maximum of 256 files can be recognized.
- Up to 8 hierarchies can be created.
This DVD system recommends the use of files recorded at the below specifications:
• Sampling frequency: 44.1kHz or 48kHz
• Constant bit rate: 112kbps ~ 320kbps.
18
On-Screen Information
MP3
You can check the MP3 files during playback.
1 Press DISPLAY/STATUS/EXIT.
• The name of the file currently in play will be displayed.
2 Press DISPLAY/STATUS/EXIT again to show the track number, the elapsed time, the repeat status, and the playback status at the top of the screen.
• will be displayed when the repeat play has been selected.
T - indicates Track repeat
G - indicates Group (folder) repeat
A - indicates Disc repeat
3 Press DISPLAY/STATUS/EXIT again to exit.
Track Selection
MP3
1 Press SEARCH/INDEX 3during playback.
• The FILE LIST will appear.
2 Select a desired track using Arrow (L/K/B/s).
• Press B when you want to go to the next hierarchy.
• Press s when you want to go back to the previous hierarchy.
3 Press PLAY B to start playing
Notes:
- Press SEARCH/INDEX 3to EXIT.
- Some selections may take a while to be recognized.
Random Playback
MP3
1 Press MODE/SYSTEM twice while playback is stopped.
2 Press PLAY B to play the tracks in random order.
Program
MP3
This feature allows you to program a mp3 disc to play in a desired sequence.
1 Press MODE/SYSTEM during playback is stopped.
• The PROGRAM screen will appear.
2 Press K or L to select a track, then press OK, to save it in a program.
• Press CLEAR to erase the incorrect input.
3 Press PLAY B to start programmed playback.
Audio Language
DVD-V
The DVD system allows you to select a language during DVD disc (if multi language available) playback.
1 Press AUDIO/BAND during playback.
2 Press AUDIO/BAND repeatedly to select your desired language.
Notes:
- Pressing AUDIO/BAND may not work on some DVDs with multiple audio languages (e.g. DVDs which allow audio language setting on the disc menu).
- Some discs allow audio language setting on the disc menu.
(Operation varies between discs, so refer to the manual accompanying the disc.)
Stereo Sound Mode
CD
VCD
1 Press AUDIO/BAND repeatedly during playback to select between STEREO, L-CH or R-CH.
STEREO - both right and left channels are active (stereo)
L-CH - only left channel is active
R-CH - only right channel is active
E9017FD_EN.qx3 03.8.6 10:13 AM Page 19
Subtitle Language
DVD-V
The DVD system allows you to select a language for subtitle during DVD disc (if available) playback.
1 Press DVD, then SUBTITLE during playback.
2 Press SUBTITLE repeatedly to select your desired subtitle language.
• The selected language will be displayed on the display bar at the top of the screen.
3 To turn off subtitles, press SUBTITLE repeatedly until OFF appears.
Notes:
- Some discs allow subtitle language setting on the disc menu. (Operation varies between discs, so refer to the manual accompanying the disc.)
- If the desired language is not shown after pressing SUBTI-
TLE several times, the disc does not have subtitles in that language.
- If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the
Subtitle language setting. If you choose any other languages, ‘---’ will be displayed instead. (Details are on page
21.)
Camera Angle
DVD-V
Some DVD discs contain scenes which have been shot simultaneously from various angles.You can change the camera angle when the ( ) icon appears on the screen.
1 Press DVD, then ANGLE during playback.
• The selected angle will be displayed on the display bar at the top of the screen.
2 Press ANGLE repeatedly to select your desired angle.
Changing the On-Screen Display
DVD-V
You can check information about the current disc by pressing DISPLAY/STATUS/EXIT on the remote control.
1 Press DISPLAY/STATUS/EXIT during playback to show current
Chapter.
a The elapsed and remaining playing time of the current chapter will be displayed.
2 Press DISPLAY/STATUS/EXIT again to show current Title.
a The elapsed and remaining playing time of the current title will be displayed.
3 Press DISPLAY/STATUS/EXIT the third time.
a The BIT RATE, layer number (if available) and the current repeat setting will be displayed.
4 Press DISPLAY/STATUS/EXIT the fourth time to remove the display.
CD
VCD
1 Press DISPLAY/STATUS/EXIT during playback, the current
Track will be displayed on the TV screen.
a The elapsed and remaining playing time of the current total track will be displayed.
2 Press DISPLAY/STATUS/EXIT again to show current Total
Track.
a The elapsed and remaining playing time of the current total track will be displayed.
3 Press DISPLAY/STATUS/EXIT the third time to remove the display.
Playing a Disc
Parental Control
DVD-V
Parental Control limits the disc viewing that exceed your settings. (with a password or playback will stop.)
This feature allows you to prevent discs with alternative scenes from being played by your children.
Parental Level
Parental Level allows you to set the rating level of your DVD discs. Playback will stop if the disc’s ratings exceed the level you set.
1 Press SYSTEM MENU/PROG in STOP mode.
2 Press B to select CUSTOM, then press OK.
3 Press s or B to select PARENTAL, then press OK.
4 Enter your four-digit password then press OK.
5 Press K or L to select PARENTAL
LEVEL, then press OK.
6 Press K or L to select the desired level, then press OK.
7 Press SYSTEM MENU/PROG to exit.
PARENTAL
PARENTAL LEVEL ALL
Notes:
- When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the password from the second time onward.
- To change the password, press K or L to select CHANGE,
then press OK. Enter the four-digit pass-word, then press
OK.
- With some DVDs, it may be difficult to find if they are compatible with parental lock. Be sure to check if the parental lock function operates in the way that you have set.
- Record the password in case you forget it.
If You Forget the Password
1 Press 4, 7, 3, 7 at step 4.
• Password will be cleared and parental level will be set to ALL.
2 Proceed the above steps 4-5 again.
Control Levels
ALL
All parental lock is cancelled.
Level 8
DVD software of any grade (adult/general/children) can be played back.
Levels 7 to 2
Only DVD software intended for general use and children can be played back.
Level 1
Only DVD software intended for children can be played back, with those intended for adult and general use prohibited.
Marker Setup Screen
DVD-V
CD
VCD
Use markers to memorise your favourite places on a disc.
1 Press SEARCH/INDEX 3four times (CD/VCD: three times) during playback.
• The display screen and Markers will appear on the TV screen.
2 Press s or B to select 1, 2, 3, 4, 5, 6, 7, 8, 9, or 10 and ensure that
“- - - - : - -” appears in the display.
3 When reaches the desired point, press OK.
• The Title or Track and elapsed playing time will appear in the
TV screen.
4 To return to the Marker later, press SEARCH/INDEX 3four times (CD/VCD: three times) during playback and s or B to choose the desired marker, then press OK.
Notes:
- Opening the disc tray or turning off the power or select
AC at step 2 and press OK will erase all Markers.
- To clear a marker, using s or B, position the cursor on
to the marker number to be cleared and press CLEAR.
- You can mark up to 10 points.
5 Press SEARCH/INDEX 3or RETURN to exit.
19
E9017FD_EN.qx3 03.8.6 10:13 AM Page 20
DVD Setup
Audio Setting
Choose the appropriate Audio settings for your equipment as it only affect during the playback of DVD discs of the DVD system.
1 Press SYSTEM MENU/PROG in STOP mode.
2 Press B to select CUSTOM, then press OK.
• CUSTOM mode will appear.
3 Press s or B to select AUDIO, then OK to confirm.
4 Press K or L to select the below items, then press OK.
DRC (Dynamic Range Control) :
To compress the range of sound volume.
The default setting is OFF.
DOLBY DIGITAL :
QUICK
Set to ON when the player is connected to Dolby Digital Decoder.
(ON : Output by Dolby Digital)
(OFF : Convert the Dolby Digital to PCM)
The default setting is ON.
DOWN SAMPLING :
Set to ON when outputting in 48kHz.
The default setting is ON.
AUDIO
DRC
DOLBY DIGITAL
OFF
ON
DOWN SAMPLING ON
MPEG
5.1CH
OFF
When playing disc with copyright Protection
• If you select OFF, copyright protection will be activated and sound will be down sampled at 48kHz.
MPEG :
Set to ON when the player is connected MPEG Decoder.
(ON: Output by MPEG)
(OFF: Convert the MPEG to PCM)
• The default setting is OFF.
5 Press SYSTEM MENU/PROG to exit.
Delay Time
Set the delay time for the Center and Rear (Surround) speakers to suit your listening position. If you usually sit closer to the
Center speaker than the Front speakers, increase the Center delay time to improve the Surround Sound effect. If you plan to sit closer to the Rear speakers than the Front speakers, increase the Rear delay time.
1 Press DVD to put the DVD system in DVD mode.
• The red DVD light will be on the front of the DVD system.
Press STOP C to stop Disc playback if necessary.
2 Press SYSTEM MENU/PROG.
• The QUICK SETUP screen will appear.
3 Press B to select CUSTOM at the top of the menu, then press
OK.
• This menu will appear.
4 Press B to select AUDIO at the top of the menu, then press OK.
5 Press p to select 5.1CH, then press
OK.
6 DELAY TIME will be selected. Press
OK.
AUDIO
DRC
DOLBY DIGITAL
OFF
ON
DOWN SAMPLING ON
MPEG
5.1CH
OFF
7 Press o or p to select CENTER or SURROUND (for the
REAR speakers), then press OK.
8 Press o or p to select a delay time in milliseconds, then press
OK.
• The default setting for the CENTER Delay time is 0 ms.The
default setting for the SURROUND (rear) Delay time is 5 ms.
9 Press SYSTEM MENU/PROG to remove the menu.
Speaker Balance
You can test the volume balance of each speaker with this procedure.
1 Press DVD to put the DVD system in DVD mode.
• The red DVD light will be on the front of the DVD system.
Press STOP C to stop Disc playback if necessary.
2 Press SYSTEM MENU/PROG.
• The QUICK SETUP screen will appear.
3 Press B to select CUSTOM at the top of the menu, then press
OK.
• This menu will appear.
4 Press B to select AUDIO at the top of the menu, then press OK.
5 Press p to select 5.1CH, then press
OK.
6 Press p to select BALANCE, then press OK.
AUDIO
DRC
DOLBY DIGITAL
OFF
ON
DOWN SAMPLING ON
MPEG OFF
5.1CH
7 TEST will be selected. Press OK.
• The test sound will come from each speaker (in the order indicated in the menu) so you can check the volume of each speaker.
8 Press OK to stop the test.
9 Press o or p to select the speaker for which you want to adjust the volume, then press OK.
• You will hear the test sound from that speaker.
10 Press o or p to adjust the volume of the selected speaker, then press OK.
• The BALANCE menu will reappear, showing the value you selected for that speaker.The available volume range is -6 dB to +6 dB. Press o or p to see all the available dB values.
11 Press SYSTEM MENU/PROG to remove the menu.
Note:
- You cannot hear the test sound from the Subwoofer.
Language Setting
DVD-V
Language options are not available with some discs.
1 Press SYSTEM MENU/PROG in STOP mode.
2 Press B to select CUSTOM, then press OK.
• CUSTOM mode will appear.
3 Press s or B to select LANGUAGE, then OK to confirm.
4 Press K or L to select the below items, then press OK.
AUDIO :
Sets the audio language.
SUBTITLE :
Sets the subtitle language.
DISC MENU :
Sets the language for DVD Menu.
PLAYER MENU :
QUICK
Sets the language for the On-Screen display.
5 Press K or L to select a setting, then press OK.
• If OTHER is selected in the AUDIO, SUBTITLE or DISC
MENU screen, press four-digit number to enter the code for the desired language. (Refer to the language code list on page
21).
• Only the languages supported by the disc can be selected.
6 Press SYSTEM MENU/PROG to exit.
Note:
- Language Setting for Audio and Subtitle is not available with some discs.Then use AUDIO and SUBTITLE. Details are on pages 18-19.
20
E9017FD_EN.qx3 03.8.6 10:13 AM Page 21
DVD Setup
Language
A-B
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
C-E
Cambodian
Catalan
Chinese [CHI]
Corsican
Croatian
Czech
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
Faroese
Fiji
Finnish [FIN]
F-H
Display Setting
DVD-V
Use markers to memorise your favourite places on a disc.
1 Press SYSTEM MENU/PROG in STOP mode.
2 Press B to select CUSTOM, then press OK.
• CUSTOM mode will appear.
3 Press s or B to select DISPLAY, then OK to confirm.
4 Press K or L to select the below items, then press OK.
TV ASPECT :
QUICK
Press K or L for an item selection, then press OK.
Select 4:3 LETTER BOX for a black bars appears on top and bottom of
DISPLAY
TV ASPECT 4:3 LETTER BOX
ANGLE ICON ON
AUTO POWER OFF ON the screen.
Select 4:3 PAN & SCAN for a full height picture with both sides trimmed.
Select 16:9 WIDE if a wide-screen TV is connected to the DVD system.
The default setting is 4:3 LETTER BOX.
ANGLE ICON :
Press OK repeatedly to turn Angle icon ON or OFF.
The default setting is ON.
AUTO POWER OFF :
Press OK repeatedly to turn Auto Power off ON or OFF.
The default setting is ON and it will turn the DVD system to off automatically after 35 minutes of no use.
5 Press SYSTEM MENU/PROG to exit.
Notes:
- Be sure to press SYSTEM MENU /PROG, or the setting will not work.
- You can also choose the item by pressing the numbers.
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
Code Language
5261
5256
5255
Code Language
French [FRE]
Frisian
Galician
Georgian
German [GER]
Greek [GRE]
5264
5271
5358
5747
5051
5158
Greenlandic
Guarani
Gujarati
5758
5360
5367
Hausa
Hebrew
5447
5569
Hindi 5455
Hungarian [HUN] 5467
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean [KOR]
Kurdish
L-N
Laothian
Latin
Latvian;Lettish
Lingala
Lithuanian
5861
5847
5868
5860
5866
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
Code
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
5957
5953
5965
5958
5966
5955
Marathi
Moldavian
Mongolian
5964
5961
5960
Nauru
Nepali
6047
6051
Norwegian [NOR] 6061
O-R
Occitan
Oriya
Oromo(Afan)
Panjabi
Pashto;Pushto
Persian
6149
6164
6159
6247
6265
5247
Polish 6258
Portuguese [POR] 6266
Quechua
Rhaeto-Romance
6367
6459
Romanian [RUM] 6461
Russian [RUS] 6467
S
Samoan
Sangho
Sanskrit
6559
6553
6547
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
5350
6564
6554
6566
6660
6560
6550
6555
Language
Siswat
Slovak
Slovenian
Somali
Spanish [SPA]
Sundanese
Swahili
Swedish [SWE]
T
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish [TUR]
Turkmen
Twi
U-Z
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
Code
6565
6557
6558
6561
5165
6567
6569
6568
21
E9017FD_EN.qx3 03.8.6 10:13 AM Page 22
FM/MW Radio
Selecting Radio Station
1 Press TUNER to select Tuner mode.
• The red TUNER light will appear on the front of the System.
The current radio frequency (station number) will appear on the display panel.
2 Press AUDIO/BAND to select FM or MW.
3 Press s or B to select a preset radio station.
You also can select a preset radio station by pressing the
Number buttons.
• The preset number will appear in the display panel to the left of the station’s frequency.When choosing preset stations 10 and above, enter both digits within two seconds to ensure you enter the complete number.
4 Press SKIP/P+ i or SKIP/P– j to change the radio frequency by one-tenth.
• For example, to go from 100.1 to 100.2, press SKIP/P+ i.
Use these buttons to fine-tune the station you want.
Or, to search for the next available station, press and hold
SKIP/P+ i or SKIP/P– j for one second, then release.
SEARCH will appear on the display panel when you release the button.When a station with sufficient signal strength is found, the station will be tuned and searching will stop.You
can press and hold SKIP/P– j to search backward to the last available station.
Note :
- If the sound is distorted during MW reception, press
o
/ p on the remote to reduce the noise.This is effective
only for the current MW station.This does not work for every situation.There may be interference from other electrical appliances or weak MW signals.
Preset Radio Stations
Automatic Presetting
You can store up to 40 preset radio stations automatically by following these steps.
1 Press TUNER to select Tuner mode.The red TUNER light will appear on the front of the System.
2 Press and hold SYSTEM MENU/PROG until AUTO appears on the System’s display panel, then release SYSTEM MENU/PROG.
The System will start scanning for stations. FM stations will be set first, followed by MW stations.The System will store the first 40 stations found.When programming is finished, the last preset station will be tuned.
3 Or, you can press SYSTEM MENU/PROG or STOP C to stop presetting stations.The radio stations scanned so far will be stored.The last stored station will be tuned.
Note :
- If a radio station has been stored in one of the presets, it will not be stored again under another preset number during Automatic Presetting.
Manual Presetting
If Automatic Presetting does not memorize all the stations you want, you can preset individual stations manually.
1 Press SKIP/P+ i or SKIP/P– j to select the station you want to designate as a preset station.
2 Press SYSTEM MENU/PROG.The next available preset number and the station’s frequency will blink in the display panel.To
store the station under a different preset number, press { or
B to choose a preset number.
If Prog ... FULL appears before the station’s frequency starts blinking, there are already 40 presets. Press { or B to choose a preset that you want to replace with the new station you are presetting now.
3 Within 20 seconds, press SYSTEM MENU/PROG to store the radio station under the designated preset number. (After 20 seconds, the Tuner will exit presetting mode. If you’ve made a mistake, wait 20 seconds for the frequency and preset number to stop flashing, then try again.)
Note :
- To erase a preset, press B or { to select the preset sta-
tion you want to delete.Then, press and hold STOP C on
the remote until PRESET . . . DELETED appears on the
System’s display panel.The preset numbers of all other radio stations with higher numbers will decrease by one.
Maintenance
Cleaning the Cabinet
• Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasives.
Cleaning Discs
• When a disc becomes dirty, clean it with a cleaning cloth.Wipe the disc from the centre out. Do not wipe in a circular motion.
• Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analogue records.
Cleaning the disc lens
• After prolonged use, dirt or dust may accumulate at the disc lens.To ensure good playback quality, clean the disc lens with Philips CD
Lens Cleaner or any commercially available cleaner. Follow the instructions supplied with the cleaner.
22
E9017FD_EN.qx3 03.8.6 10:13 AM Page 23
VCR Video Heads
Four heads - Hi-Fi
Antenna
VHF/UHF - 75 ohm external antenna terminal
DVD Color System
PAL
Amplifier
Output power (rms, 4 ohms, 1 kHz, 10% Total
Harmonic Distortion) 360W total
- Front 75W/channel
- Center 75W
- Rear (Surround) 75W/channel
- Subwoofer 75W
FTC(Federal Trade Commission)
(4 ohms, 120 Hz to 12.5 kHz,
10 % Total Harmonic Distortion)
2 X 60W
Frequency Response
DVD (linear sound):
20 Hz to 22 kHz
(sample rate: 48 kHz)
20 Hz to 44 kHz (surround off)
(sample rate: 96 kHz)
Audio CD: 20 Hz to 20 kHz
Signal-to-Noise Ratio
Audio CD: 120 dB (JEITA:
Japan Electronics and Information Technology
Industries Association)
Dynamic Range
DVD (linear sound): 99 dB
Audio CD: 99 dB (JEITA)
Total Distortion Factor
Audio CD: 0.003% (JEITA)
DVD: 0.003%
Wow and Flutter
Below the measurement limitation
(±0.001% W PEAK) (JEITA)
Power Requirement
220–240V AC, 50 Hz
Power Consumption
Power on: 50 W
Power off (standby): 5 W
( When CLOCK DISPLAY set to OFF. )
Operating Temperature
5°C to 40°C
Relative Humidity
30% to 80%
Specifications
Dimensions (w x h x d)
Receiver (System):
43.5 x 9.9 x 39.2 cm
Front Speakers:
9.4 x 15.5 x 8.9 cm
Rear Speakers:
9.4 x 15.5 x 8.9 cm
Center Speaker:
43.5 x 7.2 x 6.4 cm
Subwoofer:
19.6 x 39.1 x 43.2 cm
Weight
7.8 kg
NOTE: Designs and specifications are subject to change without notice.
Problem
No power
No picture
Distorted picture
Completely distorted picture or black/white picture with DVD
No sound or distorted sound
No audio at digital output
No DTS audio at analog output
No sound and picture
Picture freezes momentarily during playback
Disc can’t be played
No return to start-up screen when disc is removed
The System does not respond to the remote control
Buttons do not work or the System stops responding
The System does not respond to some operating commands during playback.
The DVD system cannot read CDs/DVDs
The System switches from DVD mode to VCR mode after 35 minutes
The VCR do not record a TV program
The System does not perform a timer
The motor (cylinder) rotates even when tape playback is stopped
You cannot insert a tape
You cannot remove a tape
The System ejects the tape when you press REC or TIMER SET for a timer recording.
Radio reception is poor.
Troubleshooting
Solution
– Check if the AC power cord is properly connected.
– Check if the TV is switched on.
– Check the video connection.
– Sometimes a small amount of picture distortion may appear.This is not a malfunction.
– Connect the DVD system directly to the TV.
– Make sure the disc is compatible with the DVD system.
– Adjust the volume.
– Check that the speakers are connected correctly.
– Check the digital connections.
– Check if the audio format of the selected audio language matches your receiver capabilities.
– Use a DIGITAL AUDIO OUT jack when outputting the DTS audio.
– Check that the SCART cable is connected to the correct device (See Connecting to a TV)
– Check the disc for fingerprints/scratches and clean with a soft cloth wiping from centre edge.
– This may happen when you use the disc recorded in the non-seamless manner.This is not a malfunction.
– Ensure the disc label is facing up.
– Check if the disc is defective by trying another disc.
– Reset the unit by switching the DVD system off, then on again.
– Aim the remote control directly at the sensor on the front of the System.
– Reduce the distance to the System.
– Replace the batteries in the remote control.
– Re-insert the batteries with their polarities (+/– signs) as indicated.
– To completely reset the System, unplug the AC cord from the AC outlet for 5-10 seconds.
– Operations may not be permitted by the disc.
Refer to the instructions of the disc.
– Use a commonly available cleaning CD/DVD to clean the lens before sending the DVD system for repair.
– Playback will stop for more than 35 minutes and no button is pressed.
– Make sure the tape has a record tab.
– Make sure the System is in VCR position.
– Check the TV and the System channel are similar.
– Make sure the recording start and stop times are set correctly.
– Make sure the tape has a record tab.
– Make sure the clock is set.
– The System may not perform or continue a timer recording if the power fails for more than
1 minute.
– To enable quick play mechanism, the cylinder will rotate for about five minutes.This is normal.
– Insert a tape, window side up with the record tab facing you.
– Gently push on the center of the tape when putting into the System.
– Make sure the power plug is completely connected to a power outlet.
– Make sure the tape has a record tab.
– If the signal is too weak, adjust the antenna or connect an external antenna for better reception.
– Increase the distance between the System and your other electronics equipment.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre (HOTLINE).
23
E9017FD_EN.qx3 03.8.6 10:13 AM Page 24
PHILIPS NORGE AS
Sandstuveien 70,
PO Box 1, Manglerud
N-0612 Oslo
NORWAY
Phone: 2274 8250
OY PHILIPS AB
Sinikalliontie 3,
02630 Espo
Helsinki
FINLAND puh. 09 615 80 250
PHILIPS KUNDTJÄNST
Kollbygatan 7,
Akalla,
16485 Stockholm
SWEDEN
Phone: 08-598 52 250
PHILIPS POLSKA
AL. Jerozolimskie 195B
02-222 Warszawa
POLSKA
Tel.: (022)-571-0-571
PHILIPS SERVICE
V Mezihori 2
180 00 Prage
CZECH REPUBLIC
Phone: (02)-3309 9240
PHILIPS Iberia, S.A.
C/Martinez Villergas, 49
28027 MADRID
SPAIN
Phone: 902-11 33 84
PHILIPS
Österreichische Philips Industrie
GmbH
Triesterstrasse 64
1101 Wien
AUSTRIA
Tel: 0810 001 203
PHILIPS INFO CENTER
Alexanderstrasse 1
20099 Hamburg
GERMANY
Tel: 0180-53 56 767
SERVICE CONSOMMATEURS
PHILIPS
BP 0101
75622 Paris Cédex 13
FRANCE
Phone: 0825-889 789
PHILIPS ELECTRONICS
IRELAND LIMITED
Consumer Information Center
Newstead, Clonskeagh
DUBLIN 14
Phone: 01-7640292
PHILIPS CONSUMER
ELECTRONICS
Servizio Consumatori
Via Casati 23
20052 Monza - Milano
ITALY
Phone: 800 820026
PHILIPS MÁRKASZERVIZ
Kinizsi U 30 - 36
Budapest 1092
HUNGARY
Phone: (01)-2164428
PHILIPS PORTUGUESA, S.A.
Consumer Information Center
Rua Dr. António Loureiro Borge, nr.5
Arquiparque, Miraflores
P-2795 L-A-VEHLA
PORTUGAL
Phone: 021-4163063
PHILIPS CE,The Philips Centre,
420 - 430 London Road,
Croydon, Surrey
CR9 3QR
UNITED KINGDOM
Phone: 0208-665-6350
CONSUMER SERVICES
Prags Boulevard 80. PO Box 1919,
DK-2300 Copenhagen S
DANMARK
TIf: 32 88 32 00
PHILIPS REPRESENTATION
OFFICE
Ul. Usacheva 35a
119048 MOSCOW
RUSSIA
Phone: 095-937 9300
PHILIPS INFO CENTER
Fegistrasse 5
8957 Spreitenbach
SUISSE
Tel.: 0844-800 544
PHILIPS CUSTOMER CARE
CENTER
Twee Stationsstraat 80/
80 Rue des Deux Gares
1070 BURSSEL/BRUXELLES
BELGIUM (for BENELUX)
Tel: 070-222303
Meet Philips at the Internet http://www.philips.com
The products and services described herein are not necessarily available in all countries
Due to continuous product improvements this document is subject to change without notice.
Printed in China
0VMN03815 / E9017FD*****
advertisement
Key Features
- DVD recorder Grey
- 450 W 6.1 channels
- DTS Digital Surround, Dolby Digital
- 120 dB Equalizer MP3 bit rates: 112 - 320 Kbit/s
- FM radio
- 30 - 20000 Hz
Related manuals
advertisement
Table of contents
- 2 Environmental Information
- 2 Supplied Accessories
- 2 Safety Information
- 2 Symbols Used in this Manual
- 4 Front Panel
- 4 Display Message
- 5 Rear Panel
- 5 Remote Control
- 6 Basic Connections
- 6 Connecting to a TV
- 7 (for DVD features)
- 7 Antenna Connections
- 7 Connecting the speaker wires to the speaker jacks
- 8 Setting up Surround Sound
- 8 External Input Mode (for VCR features)
- 8 Inserting batteries into the Remote Control
- 8 Using the Remote Control
- 8 Playable Video Cassette Tapes
- 8 Turning on your System
- 9 Automatic Channel Setup
- 9 Manual Channel Preset
- 9 Follow TV (Automatic TV channels sorting)
- 10 Sorting and clearing TV channels manually
- 10 Setting the language (for VCR features)
- 10 Setting the clock
- 10 Decoder allocation (for VCR features)
- 11 Playing cassettes
- 11 Playing back NTSC cassettes
- 11 Displaying current tape position
- 11 (scanning)
- 11 Still picture / slow motion
- 11 (forward wind and rewind)
- 11 Index search
- 11 Manual Tracking
- 12 General information
- 12 Recording without automatic switch-off
- 12 Linking up recordings (assemble cut)
- 12 Selecting the recording speed (SP or LP)
- 12 receiver (RECORD LINK)
- 12 'Direct Record
- 12 Switching 'Direct Record' on or off
- 13 Direct dubbing
- 13 Recording (From DVD To VCR)
- 13 General information
- 13 ® system')
- 14 system)
- 14 OTR (One Touch Recording)
- 14 a programmed recording (TIMER)
- 14 Hints for Timer Recording
- 15 Switching the status display off or on
- 15 Blue Background on or off
- 15 Clock Display
- 15 Selecting the sound channel
- 15 Digital Sound
- 15 Surround Sound
- 16 Basic Playback
- 16 General Features
- 16 Pause
- 16 Disc Menus
- 16 Title Menu
- 16 Calling Up a Menu During Playback
- 16 Step by Step Playback
- 16 Resume
- 16 Fast Forward / Reverse Search
- 16 Slow Forward / Slow Reverse
- 17 Track
- 17 Title / Chapter Search
- 17 Time Search
- 17 Repeat
- 18 Program
- 18 Random Playback
- 18 MP3/JPEG Playback
- 18 On-Screen Information
- 18 Track Selection
- 18 Random Playback
- 18 Program
- 18 Audio Language
- 18 Stereo Sound Mode
- 19 Subtitle Language
- 19 Camera Angle
- 19 Changing the On-Screen Display
- 19 Parental Control
- 19 Marker Setup Screen
- 20 Audio Setting
- 20 Delay Time
- 20 Speaker Balance
- 20 Language Setting
- 21 Display Setting
- 22 Selecting Radio Station
- 22 Preset Radio Stations
- 22 Maintenance
- 23 Specifications
- 23 Troubleshooting