Milwaukee 49-16-2673 Operator’s manual

Punches, Dies, and Draw Studs

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.

Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious injury.

Save all warnings and instructions for future reference.

Before using the Punch, Die and Draw Stud, read this instruction sheet, your tool's operator’s manual, and all labels on the tool.

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.

• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from

moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

• Use tool only as directed. Only trained personnel should operate tool.

• Do not use in or near live electrical panels. Only work on de-energized electrical panels. Disconnect all electrical current before use to avoid the risk of electric shock.

• Keep hands away from knockout die and punch while tool is in use. Fingers could be crushed or severed.

• To reduce the risk of injury, wear safety goggles or glasses with side shields. Before use, inspect and

discard workpieces and accessories with cracks or damage. Shards from weakened metal could cause injury.

• Avoid contact with punched metal edges. Edges may be sharp and could cause injury.

• Do not attempt to punch through more than one layer of material at a time. Punching through multiple layers could cause the material and accessories to warp break, throwing shards that could cause injury.

• Use tool only with knockout dies and punches rated for the peak output force of the tool. Ensure all

threads are hand-tightened securely before operating. Other uses may cause injury or damage to the tool, accessories, and workpiece.

SYMBOLOGY

WARNING Risk of electric shock. Do not use in or near live electrical panels.

Always wear eye protection

WARNING Keep hands away from punch and die. Fingers could be crushed or severed.

Conduit

Size

Nominal

Hole Size

Die

Part Number

Punch

Part Number

1/2"

1/2"

3/4"

1"

1-1/4"

1-1/2"

2"

2-1/2"

3"

1-3/8"

1-47/64"

(34.9 mm)

(44 mm)

1-63/64" (50.4 mm)

2-15/32"

2-31/32"

(62.7 mm)

(75.4 mm)

3-19/32" (91.3 mm)

1/2"

1/2"

3/4"

1"

1-1/4"

1-1/2"

2"

2-1/2"

3"

49-16-2660

49-16-2660S

49-16-2662

49-16-2664

49-16-2666

49-16-2668

49-16-2670

49-16-2672

49-16-2674

1/2"

1/2"

3/4"

1"

1-1/4"

1-1/2"

2"

2-1/2"

3"

49-16-2661

49-16-2661S

49-16-2663

49-16-2665

49-16-2667

49-16-2669

49-16-2671

49-16-2673

49-16-2675

3-1/2" 3-1/2" 49-16-2676 3-1/2" 49-16-2677

4" 4-41/64" (117.9 mm) 4" 49-16-2678 4" 49-16-2679

** It is recommended to use Grease S2 49-08-5262 on all draw stud threads before beginning a punch

7/16"

3/4"

3/4"

3/4"

3/4"

3/4"

1-1/8"

1-1/8"

1-1/8"

1-1/8"

Draw Stud

Part Number

For use in 10 ga Mild Steel

12 ga Stainless Steel

--

49-16-2680

49-16-2681

49-16-2681

49-16-2681

49-16-2681

49-16-2681

49-16-2682

49-16-2682

49-16-2682

49-16-2682

Thrust Bearing Draw Stud

Part Number

For use in 10 ga Mild Steel

3/8"

3/4"

3/4"

3/4"

3/4"

3/4"

--

--

49-16-2621

--

49-16-2622

49-16-2622

49-16-2622

49-16-2622

49-16-2622

--

--

Pilot Hole

Diameter

7/8" (22 mm)

7/8" (22 mm)

7/8" (22 mm)

7/8" (22 mm)

1-1/4" (32 mm)

1-1/4" (32 mm)

1-1/4" (32 mm)

Grease

**

S2 49-08-5262

S2 49-08-5262

--

--

--

--

**

--

**

**

58-22-xxxxd1

MILWAUKEE ELECTRIC TOOL CORPORATION

13135 West Lisbon Road • Brookfi eld, Wisconsin, U.S.A. 53005

12/13 Printed in China

96xxxxxxx-01( )