Nexus Weather Station

Introduction

Congratulations on your purchase of the “Nexus” Weather Station. The weather station consists of a main console unit, as well as an assortment of remote sensors which collect and transmit a wide range of weather data, including outdoor temperature, humidity, wind speed and direction, rain amount and rain rate.

Before you use it

Please be sure to read the instruction manual carefully.

This information will help you to familiarise yourself with your new device, learn all of its functions and parts, find out important details about its first use and how to operate it, and get advice in the event of faults.

Following the instruction manual for use will prevent damage to the device and loss of your statutory rights arising from defects due to incorrect use.

We shall not be liable for any damage occurring as a result of not following these instructions.

Likewise, we take no responsibility for any incorrect readings and for any consequences which may result from them.

Please take particular note of the safety advice!

Please keep this manual for future reference.

For your safety:

- The product is exclusively intended for the field of application described above. The product

should only be used as described within these instructions.

- Unauthorised repairs, modifications or changes to the product are prohibited.

- The product is not to be used for medical purpose or for public information, but is intended solely

for home use.

Caution!

Risk of injury:

- Keep this instrument and the batteries out of reach of children.

- Batteries must not be thrown into the fire, short-circuited, taken apart or recharged. Risk of

explosion!

- Batteries contain harmful acids. Low batteries should be changed as soon as possible to prevent

damage caused by a leaking battery. Never use a combination of old and new batteries together or

batteries of different types. Wear chemical-resistant protective gloves and glasses when handling

leaked batteries.

Important information on product safety!

- Do not expose the instrument to extreme temperatures, vibration or shock.

- Protect the base unit from moisture.

- The outdoor thermo-hygro-transmitter is protected against splash water, but is not watertight.

Choose a shady and dry position for the transmitter.

( Kat. Nr. 35.1075 )

Instruction Manual

31

KSPO:0344-16(TFA)

TFA TE922&TS34C&TS808&TS906 MANUAL 2(Eng)

Size: W148 X H210(mm)

Material: 80 LBS WF-PAP

Printing Color: BLACK （双面印刷）

BY Lai H Z 29/04/16 Rev.2

Main Console Unit

The main console unit features a radio-controlled precision clock with alarm and weather forecast.

It measures indoor temperature and humidity, and displays weather data collected by the remote weather sensors. It also provides indication of the indoor/outdoor temperature, pressure and humidity trends, and celestial information such as moon phase, and sunrise/set times.

The main console unit stores around 3300 weather records without a computer connection. When linked to a computer using the USB cable and software provided, an unlimited number of weather records can be displayed and saved onto the computer.

Remote Weather Sensors

The remote weather sensors include a thermo-hygrometer, anemometer (wind sensor) and rain sensor. All data collected by the sensors is transmitted to the main console unit by wireless RF

(433.92Mhz). The weather station supports a maximum of 5 thermo-hygrometers, allowing 5 channels of temperature/humidity display.

Features

Weather Forecast

- Sunny, Partly Cloudy, Cloudy, Slight Rain, Heavy Rain, Snow and Unstable Weather conditions

Pressure

- Current or historical pressure (mBar/ hPa, mmHg or inHg)

- Altitude or sea level pressure adjustment for atmospheric pressure compensation

- Pressure trend indication

- Sea-level pressure history for the last 24 days

- Sea-level pressure history bar chart

Moon phase

- 12 steps of moon symbols

- Scans moon phase for year 2000 to 2099

- Moon phase history for the last or future 39 days

Radio Controlled Clock

- Time and date synchronized by radio signal DCF-77 to atomic clock precision (time and date also

Clock and Calendar (12hr/ 24 hr) (month/day or day/month)

- Different combinations of clock and calendar displays

- 6 languages for day of week (English/ German/ French/ Italian/ Spanish/ Dutch)

32 33

Alarms

- Single alarm: activated once at specified time

- Weekday alarm: activated everyday from Monday to Friday at specified time

- Pre-alarm: activated ahead of single or weekday alarm if channel 1 temperature falling to +2°C

or below. (Fixed 30 minutes)

- Programmable snooze function (1-15 minutes)

Sunrise time and sunset time

- Calculates sunrise/set times with geographical information provided by user (DST, zone time

offset, latitude, longitude)

- over 133 preset cities can be selected for automatic geographical information input

Remote temperate and relative humidity, with trend indication

- Indoor and outdoor temperature and relative humidity display (°C or °F)

- Temperature and relative humidity trend indication

- Dew point display

- Max and Min memory for temperature and relative humidity

Comfort level indicator

- Analyzes current environmental conditions (Comfort, Wet and Dry)

Rainfall measurement

- Records rainfall amount for the last hour, last 24 hours, last day, last week and last month (inch or

mm).

- Daily rainfall alert if rainfall for the current day exceed pre-specified amount.

Wind

- Temperature at place of anemometer.

- Temperature adjusted to wind chill factor. (°C or °F)

- Wind direction compass display. Wind direction angles available as compass points or bearings.

- Average wind speed and gust speed (mph, m/s, knots, and km/h)

- Daily Maximum wind speed and gust speed memory.

- Wind speed alert for average wind speed and wind gust speed.

Memory Functions

- Stores 3000 weather records (without a computer connection) with memory saving intervals (1 hr

default).

- Interval: 5 Min., 10 Min., 20 Min., 30 Min., 1 Std., 1½ Std., 2 Std., 3 Std., 4 Std., 6 Std., 24 Std.

- USB port for connection to computer to allow upload of weather records.

LED backlight

- Light sensor to automatically toggle backlight when environment lighting level is low. Can be

turned on/off or set to automatic. (Should be used with AC/DC adaptor for automatic control

function)

Other Features

- Foldable table stand for mounting display on a table or wall

34

Contents of Complete Weather Station Kit

Before installing your weather station, please check that the following are complete:

Hardware Components Fittings

Main Console Unit AC/DC 7.5V output adaptor

USB

Thermo-Hygro Sensor

Rain Sensor:

- Funnel shaped Lid with

Battery Hatch

- Sensor Base

- Bucket See

- saw Mechanism

- Protective Screen

4 screws for securing unit to ground

Anemometer (Wind

Sensor):

- Wind Cups

- Wind Vane

- Anemometer arm

- Anemometer base

4 screws for securing unit to vertical surface

2m (6ft) USB cable

35

Installing your weather station

Setting up the Remote Weather Sensors

Before starting up the main console unit, setup all the remote sensors first.

When placing the sensors, make sure that they are within receiving range of the console unit. Ideally they should be within the line of sight of the console unit. Transmission range may be affected by trees, metal structures and electronic appliances. Test reception before permanently mounting your weather station.

Also make sure that the sensors are easily accessible for cleaning and maintenance.

The remote sensors should be cleaned on a weekly basis, since dirt and debris will affect sensor accuracy.

Setting up the Thermo-Hygro Sensor(s)

1. Open the latch at the base of the thermo-hygro sensor.

2. Set the channel with a slide switch.

3. Insert 2 x “AA” size 1.5V batteries.

4. Use a pin to press the “RESET” key which is in the battery compartment of thermo-hygrometer

sensors.

5. Replace the latch and mount unit at desired location.

Placement tips:

- The thermo-hygrometer sensor should be in an area with free air circulation and sheltered from

direct sunlight and other extreme weather conditions. Place the unit in a shaded area, such as

under a roof.

- Use the wall mount and fittings provided if mounting the unit on a vertical surface.

- Avoid placing the sensor near sources of heat such as chimneys.

- Avoid any areas which collect and radiate heat in the sun, such as metal, brick or concrete

structures, paving, patios and decks.

- Ideally, place the sensor above natural surfaces such as a grassy lawn.

- The international standard height for measurements of air temperature is at 1.25m (4 ft) above

Setting up the Rain Sensor

1. Unlock the funnel-shaped top of the rain sensor by turning both knobs on the sides of the rain

sensor in an anti-clockwise direction.

2. Lift the top off the base and insert 2 x “AA” size 1.5V batteries into the battery holder.

3. Replace the lid and secure into place by turning the knobs clockwise.

4. Place the rain sensor in a location such that precipitation can fall directly into the sensor, ideally

2-3 ft above the ground.

It may be secured into place by using the four screws provided.

5. The sensor must be accurately level for optimum performance. To check if the sensor is level,

remove the lid and check if the ball bearing inside is at the midpoint of the leveler. Additionally, a

bubble level or carpenter’s level may be used.

6. Attach the protective screen onto the top of the lid. The screen will prevent any debris entering the

sensor.

Placement tips:

- The rain sensor should be placed in an open area away from walls, fences, trees and other

coverings which may either reduce the amount of rainfall into the sensor, deflect the entry of

36

wind-blown rain, or create extra precipitation runoff. Trees and rooftops may also be sources of

pollen and debris.

- To avoid rain shadow effects, place the sensor at a horizontal distance corresponding to two to

four times the height of any nearby obstruction.

- It is important that rain excess can flow freely away from the sensor. Make sure that water does

not collect at the base of the unit.

- The rainfall measurement mechanism utilizes a magnet, hence do not place any magnetic objects

around the proximity of the sensor.

Setting up the Anemometer (wind sensor)

1. Assemble the wind cups and wind vane to the anemometer arm, using the included small allen

key.

2. Insert the 2 x 1.5 V AA batteries (optional) into the battery compartment in the base, observing

the correct polarity. The anemometer is solar-powered.

The batteries will operate as a backup power source.

3. Pull off the protection foil from the solar panel.

4. Insert the adapter into the jack. The rechargeable battery is already installed and now ready to use.

5. Mount the anemometer onto a vertical surface, using the fittings provided. To allow the main

console unit to indicate the correct wind direction, the wind vane must be oriented towards the

north, while the wind vane is in line with the anemometer’s arm. Use a compass if necessary.

Note: If the wind sensor cannot be fi xed with the anemometer’s arm towards the north, as provided by the default setting, you have to adjust the anemometer manually: i. Insert the backup batteries (where required) and plug the adapter into the jack.

ii. Point the wind vane towards the north. Use a compass if necessary.

iii. Use a pin to press the “SET” key which is in the battery compartment of the wind sensor.

Above procedure must be repeated for changing battery.

Placement tips:

- Check that wind can travel freely around the anemometer and is not distorted by nearby buildings,

trees or other structures.

- For better results, place the anemometer at least 3m above local structures and obstacles. The

ground creates a frictional effect to wind flow and will attenuate readings.

- Aim for maximum exposure of the anemometer to the commonest wind directions in your area.

- The official mounting location for anemometers is 10m (33 ft) above ground level in a clear

Setting up the Main Console Unit

1. Open the latch at the back of the main console unit.

2. Insert 4 x “AA” size 1.5V batteries according to the polarities shown.

3. Reattach the latch.

4. You are highly recommended to connect the AC/DC adaptor. For the feature of the automatic

backlight control function, the AC/DC adaptor must be used.

5. If placing the console unit on a table or horizontal surface, fold out the table stand and adjust to

the optimal viewing angle.

6. If mounting the console unit on a wall or vertical surface, fold the table stand back into the unit

and use the fitting provided.

Placement tips:

Make sure that the console unit is within receiving range of all remote sensors. Ideally sensors should be within the line of sight of the console unit. Transmission range may be affected by trees, metal structures and electronic appliances. Test reception before permanently mounting your weather station.

37

The console unit measures indoor temperature, humidity, pressure and receives signals from all remote sensors and radio-clock broadcasts. Avoid placing the console unit in the following areas:

- Direct sunlight and surfaces which radiate and emit heat.

- Near heating and ventilation devices, such as heating ducts or air conditioners.

- Areas with interference from wireless devices (such as cordless phones, radio headsets, baby

listening devices) and electronic appliances.

Starting up the Main Console Unit

Once the console unit is properly powered, the display will start showing some data and weather parameters. Wait for a few minutes for the console to finish self-calibration and for the sensor readings to show up.

If “ --- ” is still displayed for the sensor reading(s), check the wireless transmission path and the batteries for the corresponding sensor.

You can try to orient the antenna for a better reception.

Buttons and its control specification

The following controls are available on both the main console unit:

UP [ ] - Switches to next mode in anti-clockwise direction

- Increment for setting parameters

DOWN [ ] - Switches to next mode in clockwise direction

- Decrement for setting parameters

SET - Rotates display for current mode

- Press and hold to enter setup or change units

- Confirmation for setting parameters

MEMORY

HISTORY

- Shows records for moon phase, temperature, humidity, rain and

wind.

- Shows history for sea-level pressure

ALARM/CHART - Shows time alarms and alerts for temperature, rain and wind.

- Press and hold to enter alarm/alert setup

- Press and hold in Pressure and Weather Forecast Mode to view

different bar-charts

CHANNEL

LIGHT/SNOOZE

- Changes temperature and humidity display to selected channel

- Press and hold to enable cycling display of channel temperature

and humidity

- Turns on backlight for 5s

- Enters Snooze mode when alarm is activated

38

The following controls are only available on the main console unit:

- Toggles the light sensor function to automatic, on or off LIGHT SENSOR

- AUTO, ON, OFF

SENSITIVITY

- HIGH/LOW

- Adjusts the sensitivity of the light sensor

Navigating between Different Modes

There are 7 modes available on the main console unit, and each one displays a different category of data. When display is in a certain mode, its corresponding icon will start flashing.

To navigate between the different modes from the main console unit, press UP [ ] to cycle through the modes in a clockwise direction or DOWN [ ] to cycle through the modes in an anticlockwise direction.

Moon Phase and Weather

- Current pressure, trend, and history bar-chart

- Weather forecast

Pressure

- Sea Level Pressure, Local Pressure, and Altitude

Time and Alarm Mode

- Radio Controlled clock showing current time and calendar

- Single alarm, weekday alarm and pre-alarm

Sunrise/Sunset Mode

- Sunrise and sunset times

- Longitude and Latitude of local area

39

Temperature and Humidity Mode

- Temperature and humidity trend and readings for indoor and selected channel

- Comfort level

- Dew point

- Temperature alerts

Rain Mode

- Precipitation amount for last hour, last 24 hour, yesterday, last week and last month

- Rainfall alert

Wind Mode

- Wind Chill

- Temperature at place of anemometer

- Wind direction

- Wind speed

- Wind gust

- Alert for wind speed and wind gust speed

Customizing your Weather Station

To fully customize the weather station to your local settings and personal preferences, the following settings are required. Please refer to the appropriate sections for detailed instructions.

Required:

- Setting Pressure Parameters during Initial Start-Up (Pressure and Weather Forecast Mode P.40)

- Setting up the Time, Date and Language (Clock and Alarm Mode: P.43)

- Setting up the Location Data (Sunrise/Sunset Mode: P.45)

Optional:

- Setting up the Time Alarms (Clock and Alarm Mode: P.43)

- Setting up the Temperature Alerts (Temperature and Humidity Mode P.46)

- Setting up the Daily Rainfall Alerts (Rain Mode P.48)

- Setting up the Wind Alerts (Winds Mode: P.49)

40

LED Backlight Options

The backlight of the main console unit can be turned permanently on/off or automatically toggled when environment lighting level is low. Use the light sensor switch at the back of the unit to select lighting preferences.

For the automatic backlight function, the sensitivity of the light sensor can be adjusted to high or low with the sensitivity switch also on the back of the console unit.

Note: Console unit must be powered with AC/DC adaptor for automatic control function

Linking the Weather Station to a Computer

Data collected by the weather station can be displayed and recorded on a computer by connecting the main console unit with the computer via USB.

Install the software provided with the weather according to the instructions on the software manual.

Connect the main console unit with the computer using the USB cable provided.

Using the Different Weather Modes

Pressure and Weather Forecast Mode

This part of the display indicates the current pressure, sea level pressure, weather forecast, moon phase and pressure trend.

A number of historical statistics can also be viewed, such as the sea-level pressure values for the last 24 hours, moon phase for the previous and next 39 days, as well as a pressure/ temperature/ humidity history bar-chart.

Pressure values may be displayed inHg, hPa/mBar or mmHg, and altitude values may be displayed in meters or feet.

Accessing Pressure and Weather Forecast Mode

From the main console unit: Press the button [ ] or [ ] until the weather forecast icon

and on the upper left of the display starts flashing.

Setting Pressure Parameters during Initial Start-Up

During the initial start-up of the main console unit, all functions in Pressure and Weather Forecast mode will be locked until the pressure settings are configured.

1. Choose Pressure Units:

The unit icon “inHg” or “mmHg” or “hPa/mBar” should be flashing. Press the button [ ] or

2. Choose Altitude Units:

Press the button [ ] or [ ] to select altitude unit as feet or meters.

3. Set Altitude:

Press the button [ ] or [ ] to adjust value. Press and hold either button for fast advance.

4. Upon completion the display will be returned to Pressure and Weather Forecast Mode.

Note: After initial start-up the altitude cannot be adjusted again until the main console unit is restarted.

41

Viewing Pressure and Altitude Data

In Pressure and Weather Forecast Mode, each press of SET rotates display between:

- Sea level pressure

- Local pressure

- Local altitude

Setting the Sea Level Pressure

1. In Pressure and Weather Forecast Mode, press SET until the sea level pressure is displayed.

2. Press and hold SET. The Sea Level Pressure display should be flashing.

3. Set Sea Level Pressure:

Press the button [ ] or [ ] to adjust value. Press and hold either button for fast advance.

4. Upon completion the display will be returned to Pressure and Weather Forecast Mode.

Setting the Pressure and Altitude Units

1. In Pressure and Weather Forecast Mode, press SET until local pressure is displayed.

2. Press and hold MEMORY. The pressure unit should be flashing.

3. Set Local Pressure Units:

Press the button [ ] or [ ] to adjust value.

4. Set Altitude Units:

Press the button [ ] or [ ] to adjust value.

5. Set Sea-Level Pressure Units:

Press the button [ ] or [ ] to adjust value.

6. Upon completion the display will be returned to Pressure and Weather Forecast Mode.

Viewing the Sea Level Pressure History

1. In all modes, pressing HISTORY will toggle the sea level pressure display.

2. When sea level pressure is displayed, press HISTORY repeatedly to view sea level pressure data

for each of the last 24 hours.

3. If no buttons are pressed for 5s, the display automatically returns to Pressure and Weather

Viewing the Pressure/ Temperature/ Humidity Bar-Charts

The bar-chart on the display can be configured to display the history data for sea-level pressure, temperature or humidity for channel 1.

In Pressure and Weather Forecast Mode, press and hold ALARM/CHART to toggle the bar-chart between:

- Sea-level pressure (“PRESSURE” should be displayed)

- Temperature (Thermometer icon and “CH1” should be displayed)

- Humidity (RH icon and “CH1” should be displayed)

Viewing Moon Phase History and Forecast

1. In Pressure and Weather Forecast Mode, press MEMORY.

2. “+ 0 days” should be flashing.

3. View Moon Phase History / Forecast:

current date. Press and hold either button for fast advance.

The corresponding moon phase will be shown.

4. To exit, press MEMORY.

Otherwise, if no buttons are pressed for 5s the display automatically returns to Pressure and

Weather Forecast Mode.

42

Understanding the Weather Forecast Display

Display and and and and and

Light Snow and and

Heavy Snow and and

NOTE:

1. The accuracy of a general pressure-based weather forecast is about 70%.

2. The weather forecasts. It may not necessarily reflect the

3. The “Sunny” icon, as applies to night time, implies clear weather.

Weather Forecast

Status

Sunny

Partly Cloudy

Cloudy

Light Rain

Heavy Rain

Unstable Weather

43

Understanding the Moon Phase Diagram

FULL LAS NEW FIRST

Clock and Alarm Mode

The main console unit can be configured to display the time, calendar or UTC time. There are three time alarms available on the console unit:

Single alarm: activated once at specified time

Weekday alarm: activated everyday from Monday to Friday at specified time

Pre-alarm: activated at specified time interval (Fixed 30 min) ahead of weekday alarm, if channel 1 temperature falling to +2 °C or below.

The snooze duration for the above alarms can also be programmed (0-15 min).

Accessing Clock and Alarm Mode

From the main console unit: Press the button [ ] or [ ] until the Time Icon flashing.

Setting up the Time, Date and Language

1. In Clock and Alarm Mode, press and hold SET to enter clock and calendar setup.

2. The day of week should start flashing in the display.

starts

Press the button [ ] or [ ] to select language for day of week: English, German, French,

Italian, Spanish or Dutch

3. Select City Code:

Press the button [ ] or [ ] to select city code for your local area. Refer to P.54 for a list of

4. (if USR was chosen for city code) Set Minute for Latitude:

You will be asked to enter your latitude in minutes (°).

Press the button [ ] or [ ] to adjust value. Press and hold either button for fast advance.

for longitude and seconds for longitude.

5. (if USR was chosen for city code) Set Time Zone:

Press the button [ ] or [ ] to adjust value in resolution of 30 min. Press and hold either

button for fast advance.

6. (if USR was chosen for city code or city is in a DST zone)

Set Daylight Saving Time Option:

Press the button [ ] or [ ] to turn DST option on or off. Press and hold either button for fast

advance.

7. Repeat the above instructions to set year, month, day, calendar display format (day/month or

month/day), time display format (12 hr/ 24 hr), local hour and local minutes.

8. Upon completion the display will return to normal Clock and Alarm Mode.

Note: Press and hold SET anytime during the setup to return to normal Clock and Alarm Mode. All settings made will be discarded.

44

Rotating between Different Clock/Calendar Displays

In Clock and Alarm Mode, each press of SET rotates clock display between:

- Hour: Minute for UTC (Coordinated Universal Time)

- Hour: Minute: Weekday

- Hour: Minute: City

- Hour: Minute: Second

- Month: Day: Year (or Day: Month Year depending on settings)

Activating/Deactivating the Time Alarms

1. In Clock and Alarm Mode, each press of ALARM/CHART rotates clock display between:

- Weekday Alarm Time (displays OFF if weekday alarm deactivated)

- Single Alarm Time (displays OFF if single alarm deactivated)

- Pre-Alarm Time (displays OFF if pre-alarm deactivated)

2. When the above alarms are displayed, pressing the button [ ] or [ ] will activate/deactivate

the corresponding alarm.

Note: Press SET anytime during alarm selection mode to return to normal clock display.

Setting up the Time Alarms

1. In Clock and Alarm Mode, press ALARM/CHART to select alarm which you wish to configure.

2. Press and hold ALARM/CHART until hour starts flashing in the display

3. Set Alarm Hour:

Press the button [ ] or [ ] to adjust value. Press and hold either button for fast advance.

4. Set Alarm Minutes:

Press the button [ ] or [ ] to adjust value. Press and hold either button for fast advance.

5. Set Duration of Snooze Function (all three alarms share same snooze time duration):

Press the button [ ] or [ ] to adjust value. Press and hold either button for fast advance.

6. Upon completion the display will be returned to the alarm selection screen.

Note: Pre-alarm cannot be activated if weekday alarm or single alarm is not enabled.

Disabling/Entering Snooze when Time Alarms are Activated

To Enter Snooze:

Press LIGHT/SNOOZE to enable snooze function.

Note: Alarm will automatically enter snooze mode if no key is pressed after the alarm sounds for 2 minutes. This will occur for a maximum of three times.

To Disable Alarm(s):

Press ALARM/CHART to disable the alarm (s).

Note: For weekday alarm, pressing ALARM/CHART will only disable the alarm for the current day. The alarm will be activated again the next day (if it falls within Monday to Friday).

Activating/Deactivating Radio Clock Reception

The main console unit synchronizes the time and date with radio clock broadcasts to maintain atomic clock precision.

45

To turn this function on/off:

Press and hold the button [ ] .

If RC reception is activated, a tower icon will start flashing beside the clock icon.

If RC reception is deactivated, the triangular tower icon will disappear.

Icon

(Flashing)

RC Reception Strength

Undefined data

Reception failed for 24 hours

Weak signal, but can be decoded

Strong signal

Note: The radio controlled signal for time (DCF 77) is transmitted from the central atomic clock in

Frankfurt/Main in short intervals. It has a reception range of approx. 1500 km. Obstructions such as concrete walls can reduce the signal range.

Sunrise/Sunset Mode

The main console unit computes the sunrise and sunset times from the user-configured location data. This includes the longitude, latitude, time zone and DST (Daylight Saving Time). Choosing a suitable city code for your area will automatically generate the correct values for the location data.

Should you wish to input your own location data or if a suitable city code could not be found, choose “USR” as the city code during setup.

A searching function is also available, which allows the sunrise/sunset times for different dates to be viewed.

Accessing Sunrise/Sunset Mode

From the main console unit: Press the button [ ] or [ ] until the sunrise and sunset icons

on the lower left of the display start flashing.

Setting up the Location Data

1. In Sunrise/Sunset Mode, press and hold SET to enter location data setup.

2. The city code in the Time and Alarm display should start flashing.

Set City Info:

Press the button [ ] or [ ] to select city code for your local area. Refer to P.54

for a list of

available codes. The corresponding longitude and latitude will be shown along with the city.

Should you wish to input your own geographical coordinates, choose “USR” as the city code

3. If “USR” was chosen, you will be asked to input your geographical coordinates.

Set Degree of Latitude:

Press the button [ ] or [ ] to adjust value. Press and hold either button for fast

advance.

46

4. Repeat above procedure to set minute of latitude, degree of longitude, minute of longitude, time

zone of the city, and DST selection.

5. Upon completion the display will be returned to Sunrise/Sunset Mode.

Note: Press and hold SET anytime during the setup to return to normal Clock and Alarm Mode. All settings made will be discarded.

Viewing the Location Data

In Sunrise/Sunset Mode, each press of SET rotates display between:

- Time and sunrise/ sunset Times

- Calendar and sunrise/ sunset Times

- Calendar and longitude/ latitude

Viewing Sunrise/Sunset Times for Different Dates

1. In Sunrise/Sunset Mode, press MEMORY.

2. The date should be flashing.

Press the button [ ] or [ ] to adjust date. Press and hold either button for fast advance.

The corresponding sunrise and sunset times will be displayed for the selected date.

3. Press MEMORY or SET to return display to Sunrise/Sunset Mode.

Understanding the Sunrise/Sunset Display

The sunrise time being displayed differs during the morning and the afternoon/night.

From 12 am to 12 pm: The sunrise time for the current day will be displayed.

From 12 pm to 12 am: The sunrise time for the next day will be displayed. “NEXT DAY” icon will be displayed above the sunrise time.

At certain locations (especially those at high latitudes), sunrise and sunset events may not occur within a 24 hour time frame.

Display

FULL

Sunrise status

Sunrise at previous day

Display

FULL

Sunset status

Sunset at next day or later

---No sunrise for the whole day ---No sunset for the whole day

Temperature and Humidity Mode

The weather station supports up to 5 remote thermo-hygrometer sensors, each sensor corresponding to a separate channel for the temperature and relative humidity display. The temperature may be shown in degrees Celsius °C or degrees Fahrenheit °F. The trend (rising, steady or falling) of all values is also indicated on the display.

The main console unit uses the indoor temperature and humidity data to compute a comfort level rating of Wet, Comfort or Dry.

A temperature alert function is available for each channel. It can be programmed to sound if the channel temperature exceeds or falls below the pre-configured upper and lower limits.

Note: The temperature alerts have a 0.5 °C hysteresis to prevent the alerts from sounding constantly due to small fluctuations near the alert value. This means that after the temperature reaches the alert value, it will have to fall below the alert value plus the hysteresis to deactivate the alert.

47

Accessing Temperature and Humidity Mode

From the main console unit: Press the button [ ] or [ ] until the OUT Icon

on the upper right of the display starts flashing.

and IN icon

Viewing Temperature and Humidity Display for each Channel

For Static Display:

In Temperature and Humidity Mode, each press of CHANNEL rotates display between different channels.

For Cycling Display:

To enable automatic rotating between different channel displays, press and hold CHANNEL, until the icon is displayed. Each valid channel will now be alternately displayed for 5s.

Rotating Between Temperature and Dew Point Display

In Temperature and Humidity Mode, each press of SET rotates temperature display between:

- Temperature and Relative Humidity

- Dew Point Temperature and Relative Humidity

Setting Units for Temperature Display (°C or °F)

In Temperature and Humidity Mode, press and hold SET to convert units between degrees Celsius

°C and degrees Fahrenheit °F.

Activating/Deactivating the Temperature Alerts

1. In Temperature and Humidity Mode, each press of ALARM/CHART rotates channel temperature

- Current Temperature for corresponding channel

- Upper Temperature Alert (displays OFF if deactivated): [ ] icon displayed

- Lower Temperature Alert (displays OFF if deactivated): [ ] icon displayed

2. When the above alerts are displayed, pressing the button [ ] or [ ] will activate/deactivate

the corresponding alert.

Setting up the Temperature Alerts

1. In Temperature and Humidity Mode, press ALARM/CHART to select alarm which you wish to

configure.

2. Press and hold ALARM/CHART until channel temperature and [ ] or [ ] icon starts

flashing in the display.

3. Set Value for Temperature Alert:

Press the button [ ] or [ ] to adjust value. Press and hold either button for fast advance.

4. Upon completion the display will be returned to the temperature alert selection screen.

Disabling when Temperature Alarms are Activated

To Disable Temperature Alarm(s):

Press ALARM/CHART to disable the alarm (s).

Viewing the Max/Min Channel Temperature and Humidity

In Temperature and Humidity Mode, each press of MEMORY rotates channel temperature and humidity display between:

- Current temperature and humidity at remote sensor

- Minimum temperature and humidity at remote sensor

- Maximum temperature and humidity at remote sensor

Resetting the Max/Min Channel Temperature and Humidity Memory

In Temperature and Humidity Mode, press and hold MEMORY to clear memory for all channels.

48

Remote Sensor Status

The wave icon above the current channel display shows the connection status of the corresponding remote sensor:

Icon Status flashing Searching for remote sensor signals

Corresponding remote sensor successfully linked

No signals received for more than 15 minutes

Activating Main Console Unit to Search for All Remote Sensor Signals

The main console unit may be manually activated to search for signals from all remote sensors.

Press and hold the button [ ] to enforce a search.

Rain Mode

The main console unit records the total amount of rainfall for the last hour, last 24 hours, yesterday, last week and last month. The rainfall may be displayed in mm or inches.

A daily rainfall alert function is available which can be programmed to sound if the daily rainfall exceeds a pre-configured limit.

Accessing Rain Mode

From the main console unit: Press the button [ ] or [ ] until the RAIN icon display starts flashing.

on the

Viewing Rain Statistics

In Rain Mode, each press of SET or MEMORY rotates display between different rain statistics:

- Last hour

- Last 24 hour

- Yesterday

- Last week

- Last month

Tip: For an estimation of the rain rate, the Last Hour rainfall value can be understood as “inch/hr” or

“mm/hr”.

Resetting the Rainfall Statistics Memory

In Rain Mode, press and hold MEMORY to reset all rainfall statistics.

Setting Units for Rain Display (inch or mm)

In Rain Mode, press and hold SET to convert units between mm and inches.

“mm” is equal to “l/m 2 ”

Activating/Deactivating the Daily Rainfall Alert

1. In Rain Mode, each press of ALARM/CHART rotates display between the current rainfall statistics and the daily rainfall alert (“ALARM HI” will be displayed).

If the alert is deactivated, “OFF” will be shown, otherwise the rainfall alert value is shown.

2. When the rainfall alert is displayed, pressing the button [ ] or [ ] will activate/deactivate it.

49

Setting up the Daily Rainfall Alert

1. In Rain Mode, press ALARM/CHART to display rainfall alert.

2. Press and hold ALARM/CHART until rainfall alert and “ALARM HI” starts flashing in the

display.

3. Set Value for Rainfall Alert:

Press the button [ ] or [ ] to adjust value. Press and hold either button for fast advance.

4. Upon completion the display will be returned to the rainfall alert display.

Disabling when Daily Rainfall Alert is Activated

To Disable Rainfall Alert:

Press ALARM/CHART to disable the alert.

Wind Mode

The wind direction is shown by an animated compass display. Its angle can be displayed as compass points (i.e. NW) or in bearings from the north (i.e. 22.5°).

The upper left of the wind display can be set to indicate the temperature at the anemometer or the temperature adjusted with a wind chill factor.

The lower left of the wind display indicates the average wind speed for the last 10 minutes, as well as gust, wind speed alert and gust alert information. It can also show records of the maximum values of wind speed and gust attained for the current day.

The wind speed and gust alert functions can be programmed to sound if the wind speed or gust exceeds a pre-configured limit. The wind speed may be displayed in km/h, mph, m/s or knots.

Note: The wind speed alert has a 5 mph hysteresis and the wind gust speed alert has a 7 mph hysteresis. The hysteresis is to prevent the alerts from sounding constantly due to small fluctuations near the alert value. This means that after the wind speed reaches the alert value, it will have to fall below the alert value plus the hysteresis to deactivate the alert.

Accessing Wind Mode

From the main console unit: Press the button [ ] or [ ] until the WIND icon display starts flashing.

on the

Configuring Wind Display

In Wind Mode, each press of SET rotates display between:

- Temperature with wind chill, wind direction in bearings

- Temperature with wind chill, wind direction in compass points

- Temperature at anemometer, wind direction in compass points

- Temperature at anemometer, wind direction in bearings

Setting Units for Wind Speed Display (km/h , mph, m/s or knots)

In Wind Mode, press and hold SET to convert wind speed units between km/h, mph, m/s or knots.

Viewing Wind Statistics

In Wind Mode, each press of MEMORY rotates wind speed display between:

- Current wind speed

- Daily maximum wind speed (“DAILY MAX” is displayed)

- Gust speed (“GUST” is displayed)

- Daily maximum gust speed (“GUST DAILY MAX” is displayed)

50

Resetting the Wind Statistics Memory

In Wind Mode, press and hold MEMORY to reset all wind statistics.

Activating/Deactivating Wind Alerts

1. In Wind Mode, each press of ALARM/CHART rotates wind speed display between:

- Current wind speed

- Wind speed alert (“ALARM HI” displayed)

- Gust alert (“GUST ALARM HI” displayed)

If the alert is deactivated, “OFF” will be shown, otherwise the alert value is shown.

2. When a wind alert is displayed, pressing the button [ ] or [ ] will activate/deactivate it.

Setting up the Wind Alerts

1. In Wind Mode, press ALARM/CHART to select alarm which you wish to configure.

2. Press and hold ALARM/CHART until alert and corresponding icon starts flashing in the display.

3. Set Value for Alert:

Press the button [ ] or [ ] to adjust value. Press and hold either button for fast advance.

4. Upon completion the display will be returned to the wind alert selection screen.

Disabling when Wind Alert is Activated

To Disable Wind Alert:

Press ALARM/CHART to disable the alert.

Maintenance

Changing Batteries

The battery statuses of the sensors are checked every hour. If the low battery indicators light up, replace the batteries for the corresponding unit immediately.

Changing Batteries for the Main Console Unit

1. To avoid losing data and records, connect the AC/DC adaptor to the main unit first.

2. Remove the latch at the back and replace all batteries. Do not mix old and new batteries.

3. Replace the cover.

Changing Batteries for the Remote Sensors

1. Replace the batteries following the setup instructions for the corresponding sensor.

2. When the batteries are properly installed, the sensor will resume sending signals to the main

To enforce a search immediately for all remote signals, press and hold the button [ ] on the

main console unit.

Cleaning

The main console unit and outer casings for the remote sensors can be cleaned with a damp cloth.

Small parts can be cleaned with a cotton tip or pipe-cleaner.

Never use any abrasive cleaning agents and solvents. Do not immerse any units with electronic parts in water or under running water.

Anemometer

- Check that the wind vane and wind cups can spin freely and are free from dirt, debris or spider webs.

51

Rain Sensor

Like all rain gauges, the rain sensor is prone to blockages due to its funnel shape. Checking and cleaning the rain sensor from time to time will maintain the accuracy of rain measurements.

- Detach the protective screen and lid. Remove any dirt, leaves or debris by cleaning the items with

soapy water and a damp cloth. Clean small holes and parts with a cotton tips or pipe-cleaner.

- Look out for spiders or insects that might have crawled into the funnel.

- Also clean the swinging mechanism with a damp cloth.

Troubleshooting

“The display shows dashes “ ---” for weather parameter(s)”

The display will show “---” when the wireless link is lost with the remote sensor for the following periods:

Thermo-hygro Sensor – 15 minutes

Anemometer (Wind Sensor) – 15 minutes

Rain Sensor – 30 minutes

Check or replace the batteries for the corresponding sensor. Then press and hold the button [ ] to enforce a search for all remote signals.

If the above does not solve the problem, check the wireless transmission path from the corresponding sensor to the main console unit and change their locations if necessary.

Although wireless signals can pass through solid objects and walls, the sensor should ideally be within the line of sight of the console unit.

The following may be the cause of reception problems:

- Distance between remote sensor and main console unit too long.

- Signal shielding materials such as metal surfaces, concrete walls or dense vegetation in the path

- Interferences from wireless devices (such as cordless phones, radio headsets, baby listening

devices) and electronic appliances.

“The weather readings do not correlate with measurements from TV, radio or official weather reports.”

Weather data can vary considerably due to different environmental conditions and placement of weather sensors.

Check the placement tips included in this manual to site your sensors in the best possible way.

“The weather forecast is inaccurate.”

The weather forecast is a prediction of weather after 12-24 hours, and may not reflect current weather conditions.

52

Waste disposal

This product has been manufactured using high-grade materials and components which can

be recycled and reused.

Never throw flat batteries and rechargeable batteries in household waste.

As a consumer, you are legally required to take them to your retail store or to appropriate collection sites according to national or local regulations in order to protect the environment.

The symbols for the heavy metals contained are: Cd=cadmium, Hg=mercury, Pb=lead

This instrument is labelled in accordance with the EU Waste Electrical and Electronic

Equipment Directive (WEEE).

Please do not dispose of this product with other household waste. The user is obligated to take end-of-life devices to a designated collection point for the disposal of electrical and electronic equipment, in order to ensure environmentally-compatible disposal.

No part of this manual may be reproduced without written consent of TFA Dostmann. The technical data are correct at the time of going to print and may change without prior notice.

The latest technical data and information about your product can be found by entering your product number on our homepage: www.tfa-dostmann.de

EU declaration of conformity

Hereby, TFA Dostmann declares that the radio equipment type 35.1075 is in compliance with

Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address: www.tfa-dostmann.de

E-Mail: [email protected]

TFA Dostmann GmbH & Co. KG, Zum Ottersberg 12, D-97877 Wertheim

4/16

Power

Main unit

A C / D C a d a p t o r 5 V 2 0 0 m A ( c e n t r e + )

Remote Thermo.-Hygro unit : use 2 pcs “AA” 1.5V battery

Remote Anemometer unit : use 2 pcs “AA” 1.5V battery

Remote Rain gauge unit : use 2 pcs “AA” 1.5V battery

Weight

Main unit : 231g (without battery)

Remote Thermo.-Hygro unit : 65g (without battery)

Remote Anemometer unit : 315g (without battery)

Remote Rain gauge unit : 290g (without battery)

Dimension

Main unit : 220(L) x 165(H) x 32(D) mm

Remote Thermo.-Hygro unit : 55.5(L) x 101(H) x 24(D) mm

Remote Anemometer unit : 405(L) x 375(H) x 160(D) mm

Remote Rain gauge unit : 163(L) x 177(H) x 119(D) mm

53

Appendix

City Codes

US and Canadian Cities

C i t y C o d e Z o n e O f f s e t

Atlanta, Ga.

Austin, Tex.

Baltimore, Md.

Birmingham, Ala.

Boston, Mass.

Calgary, Alba., Can.

Chicago, IL

Cincinnati, Ohio

Cleveland, Ohio

Columbus, Ohio

Dallas, Tex.

Denver, Colo.

Detroit, Mich.

El Paso, Tex.

Houston, Tex.

Indianapolis, Ind.

Jacksonville, Fla.

Las Vegas, Nev.

Los Angeles, Calif.

ATL -5

AUS -6

BWI -5

BHM -6

BOS -5

YYC -7

CGX -6

CVG -5

CLE -5

CMH -5

DAL -6

DEN -7

DTW -5

ELP -7

HOU -6

IND -5

JAX -5

LAS -8

LAX -8

C i t y

Seattle, Wash.

St. Louis, Mo.

Tampa, Fla.

Toronto, Ont., Can.

D S T C i t y

SU Memphis, Tenn.

SU Miami, Fla.

SU Milwaukee, Wis.

SU Minneapolis, Minn.

SU Montreal, Que., Can.

SU Nashville, Tenn.

SU New Orleans, La.

SU New York, N.Y.

SU Oklahoma City, Okla.

SU Omaha, Neb.

SU Ottawa, Ont., Can.

SU Philadelphia, Pa.

SU Phoenix, Ariz.

SU Pittsburgh, Pa.

SU Portland, Ore.

NO San Antonio, Tex.

SU San Diego, Calif.

SU San Francisco, Calif.

SU San Jose, Calif.

C o d e Z o n e O f f s e t

SEA -8

STL -6

TPA -5

Y T Z 5

D S T C i t y

SU Vancouver, B.C., Can.

SU Washington, D.C.

SU Vancouver, Canada

S U

C o d e Z o n e O f f s e t

MEM -6

MIA -5

MKE -6

MSP -6

YMX -5

BNA -6

MSY -6

NYC -5

OKC -6

OMA -6

YOW -5

PHL -5

PHX -7

PIT -5

PDX -8

SAT -6

SAN -8

SFO -8

SJC -8

SU

SU

NO

SU

SU

SU

SU

SU

SU

SU

SU

SU

SU

D S T

SU

SU

SU

SU

SU

SU

C o d e Z o n e O f f s e t

YVR -8

DCA -5

VAC -8

D S T

SU

SU

SU

World Cities

C i t y C o d e T i m e Z o n e

Addis Ababa, Ethiopia

Adelaide, Australia

ADD 3

ADL 9.5

Algiers, Algeria ALG 1

Amsterdam, Netherlands AMS 1

Ankara, Turkey

Asunción, Paraguay

Athens, Greece

Bangkok, Thailand

AKR 2

ASU -3

ATH 2

BKK 7

Barcelona, Spain

Beijing, China

Belgrade, Yugoslavia

Berlin, Germany

Birmingham, England

Bogotá, Colombia

Bordeaux, France

Bremen, Germany

Brisbane, Australia

Brussels, Belgium

Bucharest, Romania

Budapest, Hungary

Buenos Aires, Argentina

BCN 1

BEJ 8

BEG 1

BER 1

BHX 0

BOG -5

BOD 1

BRE 1

BNE 10

BRU 1

BBU 2

BUD 1

BUA -3

D S T C i t y C o d e T i m e Z o n e

NO Cairo, Egypt CAI 2

SA Calcutta, India (as Kolkata) CCU

NO Cape Town, South Africa

SE Caracas, Venezuela

SE Chihuahua, Mexico sp Copenhagen, Denmark

CPT 2

CCS -4

CUU -6

CPH 1

SE Córdoba, Argentina

NO Dakar, Senegal

SE Dublin, Ireland

NO Durban, South Africa

SE

SE

SE

NO

Frankfurt, Germany

Glasgow, Scotland

Guatemala City, Guatemala

Hamburg, Germany

SE Havana, Cuba

SE Helsinki, Finland

COR -3

DKR 0

DUB 0

DUR 2

FRA 1

GLA 0

GUA -6

HAM 1

NO

SE

SE

SE

NO

Hong Kong, China

Irkutsk, Russia

Jakarta, Indonesia

Johannesburg, South Africa

Kingston, Jamaica

HAV -5

HEL 2

HKG 8

IKT 8

JKT 7

JNB 2

KIN -5

SE

SE

NO

SE

NO

NO

SE

NO

D S T sg

NO

NO

NO

SU

SE

SH

SE

NO

SK

NO

NO

NO

C i t y C o d e

Kinshasa, Congo FIH

Kuala Lumpur, Malaysia KUL

La Paz, Bolivia

Lima, Peru

Lisbon, Portugal

Liverpool, England

LPB

LIM

LIS

LPL

London, England

Lyon, France

Madrid, Spain

Manila, Philippines

Marseille, France

Melbourne, Australia

Mexico City, Mexico

Milan, Italy

LON

LYO

MAD

MNL

MRS

MEL

MEX

MIL

0

1

1

8

1

10

-6

1

Montevideo, Uruguay

Moscow, Russia

Munich, Germany

Nairobi, Kenya

MVD

MOW 3

MUC

NBO

Nanjing (Nanking), China NKG

-3

1

3

8

T i m e Z o n e

1

8

-4

-5

0

0

New Delhi, India

Odessa, Ukraine

O s a k a , J a p a n

DST defi nition

DEL

ODS

K I X

5.5

2

9

SA = Australian DST.

SB = South Brazilian DST. Changes annually.

SC = Chile DST

SE = Standard European DST.

SG = Egypt DST

SH = Havana, Cuba DST

SI = Iraq and Syria DST

SK = Irkutsk & Moscow DST

SM = Montevideo, Uruguay DST

SN = Namibia DST

SP = Paraguay DST

SQ = Iran DST maybe changed annually.

ST = Tasmania DST

SU = Standard American DST.

SZ = New Zealand DST

NO DST = no = Places that do not observe DST

ON = Always add 1 hour with local standard time

D S T

NO

C i t y

NO

NO

SE

SE

SE

SE

NO

SE

SA

SU

NO

SE

Oslo, Norway

Panama City, Panama

Paris, France

Perth, Australia

Prague, Czech Republic

Rangoon, Myanmar

Reykjavík, Iceland

Rio de Janeiro, Brazil

Rome, Italy

Salvador, Brazil

Santiago, Chile

São Paulo, Brazil

SE

SM

SE

SK

NO

NO

Shanghai, China

Singapore, Singapore

Sofi a, Bulgaria

Stockholm Arlanda, Sweden

Sydney, Australia

Tokyo, Japan

Tripoli, Libya

Austria

NO

SE

N O

Warsaw, Poland

Zürich, Switzerland

WAW 1

ZRH 1

RKV

RIO

ROM

SSA

SCL

SPL

SHA

SIN

C o d e

OSL

PTY

PAR

PER

PRG

RGN

SOF

ARN

SYD

TKO

TRP

-4

-3

8

8

0

-3

1

-3

2

1

10

9

2

T i m e Z o n e

1

-5

1

8

1

6.5

NO sb

SE

NO sc sb

NO

NO

SE

SE

SA

NO

NO

D S T

SE

NO

SE

NO

SE

NO

SE

SE

54 55

Technical Specifications

Weather Station Receivers

Receiver (Supply=6.0V, Ta=23°C)

RF Transmission Frequency

RF Reception Range

Thermo-hygro Sensor

Wind Sensor, Rain Sensor

Maximum transmitting power and Sensor unit (Supply=3.0V, Ta=23°C)

433.92 MHz

100 meters Maximum (Line of Sight )

100 meters Maximum (Line of Sight)

Thermo-hygro Sensor, Rain sensor 0,1 mW

Wind sensor 0,15 mW

Barometric Pressure Range 500 hpa to 1100hpa ( 14.75 inHg to 32.44 inHg ),

( A t s e a l e v e l )

Altitude Compensation Range

Barometric Pressure resolution

( 3 7 4 .

5 m m H g t o 8 2 3 .

8 m m H g )

-200 m to +5000 m ( -657 ft to 16404 ft )

0.1 hpa ( 0.003 inHg, 0.08 mmHg )

Barometric Pressure accuracy

Outdoor Temperature Display Range

Indoor Temperature Display Range

Operating Temperature

Storage Temperature

Temperature accuracy

Temperature resolution

Humidity Display Range

+/- 3 hpa ( 0.009 inHg, 2.3 mmHg )

-40°C to 80°C ( -40°F to 176°F )

-9.9°C to 60°C ( 14.2°F to 140°F)

-5°C to 50°C ( 23°F to 122°F)

-20°C to 70°C( -4°F to 158°F)

+/- 1°C or +/- 2°F

0.1°C or 0.2°F

0% to 99%

+ / 5 % ( w i t h i n 2 5 % 8 0 % )

1%

H u m i d i t y a c c u r a c y

Humidity resolution

Receiving Cycle

Remote Thermo./Hygro.

R a i n g a u g e

W i n d s e n s o r

Sunrise and Sunset Accuracy

Wind Direction Range

Wind Direction Accuracy

Wind Direction Resolution

Wind Direction Starting Threshold

W i n d S p e e d R a n g e around 47s

1

3

8

3

3 s s

+/- 1min ( latitude within +/- 50° )

16 positions

+/-11.25°

22.5°

3mph

0 t o 1 9 9 .

9 m p h ( 1 9 9 .

9 K m / h , 1 7 3 .

7 K n o t s , 8 9 .

3 m / s )

Wind Speed Accuracy

Wind Speed Starting Threshold

+/- ( 2mph + 5% )

3mph

Wind/Gust Speed Display Update Interval 33 seconds

Wind/Gust Sampling Interval 11 seconds

1h/24h/yesterday Rainfall Range

Last week/ last month Rainfall Range

Temperature Sensing Cycle (indoor)

Humidity Sensing Cycle (indoor)

0.0 to 1999.9 mm ( 78.73 inch )

0 to 19999 mm ( 787.3 inch )

10s

10s

Hardware Requirement for running PC software WeatherView

Operating System: Windows 98 se or above

Memory: Ram 32 M byte or more

Hard disk: 20 M byte free space or more

Optical Device: 2 x CD-Rom drive

56