Motorola MBP36S User manual

User’s Guide
Digital Video Baby Monitor
Models: MBP36S, MBP36S-2, MBP36S-3, MBP36S-4
The features described in this User’s Guide are subject to modifications without prior notice.
Welcome...
to your new Motorola Video Baby Monitor!
Thank you for purchasing the Motorola Video Baby Monitor. Now you can
see and hear your baby sleeping in another room or you can monitor your
older children in their playroom.
Please retain your original dated sales receipt for your records.
For warranty service of your Motorola product, you will need to provide a
copy of your dated sales receipt to confirm warranty status. Registration is
not required for warranty coverage.
For product related questions, please call:
UK 0844 557 0890
ROI 08187 62092
This User's Guide provides you with all the information you need to get the
most from your product.
Before you can use the baby monitor, we recommend you insert and fully
charge the battery in the parent unit, so that it continues to work if you
disconnect it from the power supply to carry it to another location. Please
read the Safety Instructions on page 6-9 before you install the units.
Got everything?
• 1 x Parent unit
• 1 x Baby unit (Camera)
• 1 x Rechargeable Ni-MH battery pack
• 1 x Power adapter for the Parent unit
• 1 x Power adapter for the Baby unit
In multi-camera packs, you will have the additional camera and power
adapter units.
Overview of the Parent Unit
10 11
12
14
1
POWER
15
2
6
3
7
4
8
5
9
13
1.
2.
3.
4.
5.
6.
7.
8.
19
18
16
20
17
Display (LCD screen)
Up Key +
Normal Mode: Tilt Up
Menu Mode: Up
Down Key Normal Mode: Tilt Down
Menu Mode: Down
Left Key <
Normal Mode: Pan Left
Menu Mode: Left
Right Key >
Normal Mode: Pan Right
Menu Mode: Right
Menu Key M
Press to open the Menu options
OK Key O
Video ON/OFF Key V
Press to turn OFF the LCD
display
Press again to turn ON the LCD
display
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
Talk Key T
Press and hold to speak to your
baby
Power Indicator LED
BLUE when mains adapter
power on.
RED when battery low.
Unit ON/OFF LED (Green)
Audio Level LED (Green,
Orange, Red, Red)
Microphone
Power Key P
Press and Hold to turn the unit
ON/OFF
Antenna
Lift the antenna for optimal
reception
Battery compartment cover
Stand
Speaker
USB power adapter socket
AV out / Audio out
Parent unit menu icons
Signal Level (4 Levels + OFF)
Night Vision Mode (Screen changes to Black/White)
Talk Mode
Battery Level Indication (4 Levels)
Pan Left
Pan Right
Tilt Up
Tilt Down
Parent unit menu icons (cont’d)
Volume Level Control (8 Levels)
Zoom Level Control (1X, 2X)
Brightness Level Control (8 Levels)
Lullaby Control (5 Song Selections)
Alarm Setting (6h, 4h, 2h, Off
)
Temperature scale select (ºC / ºF).
Readings display in BLUE, but turn RED if > 29 ºC / 84 ºF or < 14 ºC / 57 ºF.
Displays HH ºC / ºF if > 36 ºC / 97 ºF.
Displays LL ºC / ºF if < 1 ºC / 34 ºF.
Camera Selection (scan, view, add, delete)
Screen viewing mode control (Single Screen, 4-split Screen)
V
Set Video On Timer (5 min, 30 min, 60 min)
Overview of Your Baby Unit
9
1
2
4
7
PAIR
11
3
5
6
1.
2.
3.
4.
5.
6.
Photo Sensor (Night Vision Mode)
Camera Lens
Infrared LEDs
Power LED
Microphone
Speaker
10
8
7. ON/OFF Switch
8. Power Adapter Socket
9. Antenna
10. Temperature Sensor
11. Pair Key
Important guidelines for installing your Baby Monitor
•
•
•
•
•
To use your Video Monitor Baby and Parent Units together, you must be able to establish a
radio link between them, and the range will be affected by environmental conditions.
Any large metal object, like a refrigerator, a mirror, a filing cabinet, metallic doors or
reinforced concrete between the Baby and Parent Unit may block the radio signal.
The signal strength may also be reduced by other solid structures, like walls, or by radio
or electrical equipment, such as TVs, computers, cordless or mobile phones,
fluorescent lights or dimmer switches.
Use of other 2.4 GHz products, such as wireless networks (Wi-Fi® routers), Bluetooth®
systems, or microwave ovens, may cause interference with this product, so keep the
baby monitor away at least 5ft (1.5m) from these types of products, or turn them off if
they appear to be causing interference.
If the signal is weak, try lifting up the Parent Unit Antenna, or move the Parent and/or the
Baby Unit to different positions in the rooms.
1.
2.
Safety Instructions ..................................................................................... 6
Getting Started.......................................................................................... 9
2.1
2.2
2.3
2.4
2.5
3.
Using the Baby Monitor........................................................................... 12
3.1
3.2
3.3
3.4
3.5
3.6
4.
Setting up................................................................................................... 12
Pan and Tilt ................................................................................................ 12
Night Vision Mode.....................................................................................12
Talk Mode .................................................................................................. 12
Video ON/OFF..........................................................................................12
Temperature Display (HH °C / °F or LL °C / °F) ......................................13
Parent Unit Menu Options....................................................................... 14
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
5.
6.
7.
8.
Baby Unit Power Supply .............................................................................. 9
Parent Unit Battery Installation .................................................................... 9
Parent Unit Power Supply .........................................................................10
Registration (Pairing)................................................................................. 11
View Video Through TV............................................................................ 11
Volume....................................................................................................... 14
Brightness .................................................................................................. 14
Lullaby........................................................................................................ 14
Zoom.......................................................................................................... 14
Alarm.......................................................................................................... 14
Camera Control ........................................................................................ 15
4.6.1
Add (pair) a camera .................................................................. 15
4.6.2
View a camera ...........................................................................15
4.6.3
View multi-cameras on screen .................................................. 15
4.6.4
Delete a camera ........................................................................ 16
4.6.5
Scan camera .............................................................................. 16
Temperature.............................................................................................. 16
Power Saving mode .................................................................................. 16
Disposal of The Device (environment) ................................................... 17
Cleaning .................................................................................................. 18
Help.......................................................................................................... 19
General Information ................................................................................ 21
Table of contents
5
ENGLISH
Table of contents
1. Safety Instructions
WARNING:
STRANGULATION HAZARD - Keep the
unit and adapter cord more than 1 metre
from the cot and out of the baby's reach.
NEVER place camera or cords within the
cot. Secure the cords more than 1 metre
away from the baby's reach. Never use
extension cords with AC Adapters. Only
use the AC Adapters provided.
6
Safety Instructions
ENGLISH
BABY UNIT SET UP & USE:
● Determine a location for the Baby Unit that will provide the best view
of your baby in his/her cot.
● Place the BABY UNIT on a flat surface, such as a dresser, bureau, or
shelf or mount the Unit to a wall securely using the keyhole slot in the
underside of its stand.
● NEVER place the Baby Unit or cords within the cot.
● Do not place the Baby Unit or cords in the cot or within reach of the
baby (the unit and cords should be more than 1 metre away).
WARNING
This digital video baby monitor is compliant with all relevant standards
regarding electromagnetic fields and is, when handled as described in the
User's Guide, safe to use. Therefore, always read the instructions in this User's
Guide carefully before using the device.
• Adult assembly is required. Keep small parts away from children when
assembling.
• This product is not a toy. Do not allow children to play with it.
• This baby monitor is not a substitute for responsible adult supervision.
• Keep this user's guide for future reference.
• Do not place the baby unit or cords in the cot or within reach of the baby (the
unit and cords should be more than 1 metre away)
• Keep the cords out of reach of children.
• Do not cover the baby monitor with a towel or blanket.
• Never use extension cords with power adapters. Only use the power
adapters provided.
• Test this monitor and all its functions so that you are familiar with it prior to
actual use.
• Do not use the baby monitor near water.
• Do not install the baby monitor in extreme cold or heat, direct sunlight or
close to a heat source.
Safety Instructions
7
• Only use the chargers and power adapters provided. Do not use other
chargers or power adapters as this may damage the device and battery
pack.
• Only insert a battery pack of the same type.
• Do not touch the plug contacts with sharp or metal objects.
CAUTION
There is a risk of fire or explosion if the parent unit battery is replaced by an
incorrect type.
Only use a Ni-MH rechargeable battery pack with rating: 3.6V, 900mAh.
Dispose of used batteries according to their instructions.
8
Safety Instructions
2.1
1.
ENGLISH
2. Getting Started
Baby Unit Power Supply
Connect the small plug of the power adapter to the baby unit (camera) and
the other end to a suitable mains power socket.
NOTE
Only use the enclosed power adapter (5V DC / 1000mA).
2.
3.
2.2
Slide the ON/OFF switch to the ON position. The power LED will light up
in green.
Slide the ON/OFF switch to the OFF position to turn the Baby Unit off.
Parent Unit Battery Installation
Red
Black
1.
Insert the wire tab of the rechargeable battery pack into the contact slot as
shown above and fit the battery pack into the compartment.
Small cross-head or
flat-end screwdriver.
2.
Replace the battery cover over the compartment and gently tighten the
screw in a clockwise direction using a small cross-head or flat-end
screwdriver.
Getting Started
9
2.3
Parent Unit Power Supply
IMPORTANT
Installing the rechargeable battery pack and charging it fully before use is
recommended, to allow temporary battery operation if the unit is moved.
1.
2.
3.
4.
5.
Connect the small plug of the power adapter to the parent unit and the
other end to a suitable mains power socket. Only use the enclosed power
adapter (5V DC / 600mA) with the micro-USB style plug.
Press and hold the P POWER ON/OFF button for more than 1 second
to turn ON the parent unit.
Once the baby and parent units are switched on, the display on the parent
unit will show the video captured by the baby unit.
If there is no connection or you are out of range, the video display will be
replaced by a "No Camera" symbol and the unit will beep every 5 seconds.
Move the parent unit closer to the baby unit until the link is re-established.
Press and hold the P POWER ON/OFF button, until the progress bar
finishes scrolling, to turn OFF the parent unit.
NOTE
The battery icon
turns RED to indicate that the battery is low, and it gives
a beep every 16 seconds. The battery needs to be recharged. The battery pack
takes about 12 hours to charge fully.
When charging
1.
During charging, the battery icon at the top right of the screen indicates
that it is charging. If the parent unit is turned off while charging, a plug icon
shows for 5 seconds, followed by a battery icon for 45 seconds. The Blue
LED at the top left indicates the mains adapter is plugged in.
10
Getting Started
Registration (Pairing)
The Baby monitor is pre-registered to your Parent Unit. You do not need to
register it again unless the Baby Unit loses its link with the Parent Unit.
To re-register your Baby Unit, or register a new Baby Unit, follow the procedure
below:
1. Press the M button of the parent unit and the menu bar will pop up.
is highlighted, and
2. Press the < LEFT button or > RIGHT button until
the
/
/
/
menu will pop up.
3. Press the + UP button or - DOWN button to select , and press the OK
button to confirm.
4.
/
/
/
will pop up, press the + UP button or - DOWN button
to select the desired camera position and press the O button to start
searching for a camera unit. The green audio level LED will flash rapidly
while searching.
5. Press the O button to confirm.
6. Press and hold the PAIR button underneath the baby unit until the parent
unit finds the camera, beeps and the video from the camera appears.
NOTE
If a particular Baby Unit was registered previously, registering this current
Baby Unit again will overwrite the old registration.
2.5
View Video Through TV
Connect a suitable AV cable into the AV OUT socket on the side of the Parent
Unit and into the AV input of the TV. Press the < LEFT button or > RIGHT
button to select
on the Parent unit. Select the AV input on the TV menu until
the Baby monitor picture is visible. AV cable is an optional accessory, which is to
be purchased separately.
NOTE
You can hear also your baby in mono mode by connecting the 3.5mm plug
wired headset to the AV OUT socket.
Getting Started
11
ENGLISH
2.4
3. Using the Baby Monitor
3.1
Setting up
• Place the baby unit in a convenient location (e.g. on a table) and point the
camera lens towards the area you want to monitor.
• Adjust the baby unit's head angle by panning or tilting the camera up, down,
left and right until you are satisfied with the image in the parent unit.
NOTE
Do not place the baby unit within the baby's reach! If there is interference with
the picture or sound, try moving the units to different locations, and ensure they
are not close to other electrical equipment.
3.2
Pan and Tilt
The camera can be remotely controlled from the parent unit.
1.
2.
3.3
Press the + UP button or - DOWN button to tilt upward or downward.
Press the < LEFT button or > RIGHT button to pan left or right.
Night Vision Mode
The baby unit has 8 high-intensity infrared LEDs for picking up clear images in
the dark. When the built-in photo sensor on the top of the unit detects a low level
of ambient light, the LEDs will automatically activate and the screen on the
parent unit will display in black and white. The
icon will be displayed at the
top of the screen.
3.4
Talk Mode
Press and hold the T TALK button on the parent unit to talk to your baby through
the baby unit’s loudspeaker. The T icon will be displayed at the top of the LCD
screen.
3.5
Video ON/OFF
Press the V VIDEO ON/OFF button to turn the LCD display on or off, but still
leave the audio monitor on.
12
Using the Baby Monitor
Temperature Display (HH °C / °F or LL °C / °F)
The temperature reading from the temperature sensor at the back of the Baby
Unit will be displayed at the top of the Parent Unit LCD screen.
The readings will turn RED if the temperature goes above 29°C / 84°F or below
14°C / 57°F.
The reading will change to HH °C / °F if the temperature goes above 36°C / 97°F.
The reading will change to LL °C / °F if the temperature goes below 1°C / 34°F.
Using the Baby Monitor
13
ENGLISH
3.6
4. Parent Unit Menu Options
4.1
1.
2.
3.
4.2
1.
2.
3.
4.3
1.
2.
3.
4.
4.4
1.
2.
3.
4.5
1.
2.
3.
4.
14
Volume
Press the M button and the menu bar will pop up.
is highlighted.
Press the < LEFT button or > RIGHT button until
Press the + UP button or - DOWN button to select the desired volume
level from level 0 ~ 8. (The default volume level setting is level 4.)
Brightness
Press the M button and the menu bar will pop up.
Press the < LEFT button or > RIGHT button until
is highlighted.
Press the + UP button or - DOWN button to select the desired brightness
level from level 1 ~ 8. (The default brightness level setting is level 5.)
Lullaby
Press the M button and the menu bar will pop up.
Press the < LEFT button or > RIGHT button until
is highlighted.
Press the + UP button or - DOWN button to select the desired song from
the 5 lullabies available, or the cycle option to play all 5 songs in turn. (The
default setting is lullaby OFF)
Press OK on the selected lullaby, and then press the + UP button or DOWN button to select the desired song sound level.
Zoom
Press the M button and the menu bar will pop up.
Press the < LEFT button or > RIGHT button until
is highlighted.
Press the + UP button or - DOWN button to select the 1X or 2X Zoom.
(The default setting is 1X.)
Alarm
Press the M button and the menu bar will pop up.
Press the < LEFT button or > RIGHT button until
is highlighted.
Press the + UP button or - DOWN button to select the alarm time (6h , 4h ,
2h). (The default setting is Alarm OFF.)
If an alarm time is selected, the parent unit will beep for about 45 seconds
after every 6, 4 or 2 hour period.
Parent Unit Menu Options
Camera Control
4.6.1
1.
2.
3.
4.
5.
Add (pair) a camera
Press the M button and the menu bar will pop up.
Press the < LEFT button or > RIGHT button until
is highlighted, and
the
/
/
/
menu will pop up.
Press the + UP button or - DOWN button to select , and press the OK
button to confirm.
/
/
/
will pop up, press the + UP button or - DOWN button
to select the desired camera position, and press the OK button to start
searching for a camera unit. The green audio level LED will flash rapidly
while searching.
Press and hold the PAIR button underneath the baby unit until the parent
unit finds the camera, beeps and the picture from the camera appears.
NOTE
A camera can only be registered to one parent unit at any one time.
4.6.2
1.
2.
3.
4.
View a camera
Press the M button and the menu bar will pop up.
Press the < LEFT button or > RIGHT button until
is highlighted and
the
/
/
/
menu pops up.
Press the + UP button or - DOWN button to select , and press the OK
button to confirm.
/
/
/
will pop up, press the + UP button or - DOWN button
to select desired camera, and press the OK button to view the picture from
that camera.
TIP
Quick Method to View Cameras instead of entering into the menu bar.
Directly press OK repeatedly to select ,
,
,
,
.
4.6.3
1.
2.
3.
View multi-cameras on screen
Press the M button and the menu bar will pop up.
Press the < LEFT button or > RIGHT button until
icon is highlighted.
Press the + UP button or - DOWN button to select 4-split screen On/Off.
Parent Unit Menu Options
15
ENGLISH
4.6
4.6.4
1.
2.
3.
4.
Delete a camera
Press the M button and the menu bar will pop up.
Press the < LEFT button or > RIGHT button until
is highlighted, and
the
/
/
/
menu will pop up.
Press the + UP button or - DOWN button to select , and press the OK
button to confirm.
/
/
/
will pop up, press the + UP button or - DOWN button
to select the desired CAM, and press the OK button to delete that
registration.
Note:
You are not allowed to delete the camera if there is only one registered camera
in the system.
4.6.5
1.
2.
3.
4.
Scan camera
Press the M button and the menu bar will pop up.
Press the < LEFT button or > RIGHT button until
is highlighted, and
the
/
/
/
menu will pop up.
Press the + UP button or - DOWN button to select , and press the OK
button to confirm.
The screen will then display images from different registered cameras in a
loop of
/
/
/
, changing about every 12 seconds.
TIP
Quick Method to View Cameras instead of entering into the menu bar.
Directly press OK repeatedly to select
,
, ,
,
.
4.7
1.
2.
3.
4.8
1.
2.
3.
16
Temperature
Press the M button and the menu bar will pop up.
Press the < LEFT button or > RIGHT button until is highlighted.
Press the + UP button or - DOWN button to select °C or °F.
Power Saving mode
Press the M button and the menu bar will pop up.
Press the < LEFT button or > RIGHT button until V is highlighted.
Press the + UP button or - DOWN button to select auto video off after
5 mins, 30 mins or 60 mins if not in charging mode.
Parent Unit Menu Options
ENGLISH
5. Disposal of The Device (environment)
At the end of the product lifecycle, you should not dispose of
this product with normal household waste. Take this product to
a collection point for the recycling of electrical and electronic
equipment. The symbol on the product, user's guide and/or
box indicates this.
Some of the product materials can be reused if you take them to
a recycling point. By reusing some parts or raw materials from used products
you make an important contribution to the protection of the environment.
Please contact your local authorities in case you need more information on the
collection points in your area.
Dispose of the battery pack in an environmentally-friendly manner according to
your local regulations.
Disposal of The Device (environment)
17
6. Cleaning
Clean the Baby Monitor with a slightly damp cloth or with an anti-static cloth.
Never use cleaning agents or abrasive solvents.
Cleaning and care
• Do not clean any part of the product with thinners or other solvents and
chemicals –- this may cause permanent damage to the product which is not
covered by the warranty.
• Keep the Baby Monitor away from hot, humid areas or strong sunlight, and
don't let it get wet.
• Every effort has been made to ensure high standards of reliability for your
Baby Monitor. However, if something does go wrong, please do not try to
repair it yourself –- contact Customer Service for assistance.
IMPORTANT
Always switch off and disconnect the power adapter before cleaning your baby
monitor.
18
Cleaning
ENGLISH
7. Help
Display
No display
• Try recharging or replacing the battery pack.
• Reset the units. Disconnect the battery pack of the parent unit and unplug
both the units' electrical power, then plug them back in.
• Is the unit turned on?
Press and hold the ON/OFF button P on the Parent Unit to turn it ON.
Slide the ON/OFF switch on the Baby Unit to ON.
• Is the correct camera selected?
Change the camera number, if necessary.
• Is the video display turned on?
Press the VIDEO ON/OFF button V to turn it on.
• When operating using batteries only, the Display will go blank after
5 minutes or 30 minutes or 60 minutes to save power (depending on video
on setting). The unit is still active and will give you audio alerts. You can
reactivate the screen by pressing any button.
Registration
If the Baby Unit has lost its link with the Parent Unit
• Try recharging or replacing the battery pack.
• If the Baby Unit is too far away it may be going out of range, so move the
Baby Unit closer to the Parent Unit.
• Reset the units by disconnecting them from the battery and electrical power.
Wait about 15 seconds before reconnecting. Allow up to one minute for the
Baby Unit and the Parent Unit to synchronise.
• See 2.4 Registration (Pairing), if there is a need to re-register the units.
Help
19
Interference
Noise interference on your parent unit
• Your baby and parent units may be too close. Move them farther apart.
• Make sure there is at least 1m to 2m (3 to 6 feet) between the 2 units to avoid
audio feedback, and reduce the volume of the Parent Unit.
• lf the baby unit is too far away it may be out of range, so move the baby unit
closer to the parent unit.
• Make sure the baby and parent units are not near other electrical equipment,
such as a television, computer or cordless/mobile telephone.
• Use of other 2.4 GHz products, such as wireless networks (Wi-Fi® routers),
Bluetooth® systems, or microwave ovens, may cause interference with this
product, so keep the baby monitor away at least 1.5m (5ft) from these types
of products, or turn them off if they appear to be causing interference.
• If the signal is weak, try moving the Parent and/or Baby Unit to different
positions in the rooms.
20
Help
ENGLISH
8. General Information
lf your product is not working properly....
1.
Read this User's Guide or the Quick Start Guide.
2.
Contact Customer Service:
UK
0844 557 0890
ROI 08187 62092
To order a replacement battery pack, contact customer service.
Consumer Products and Accessories Limited Warranty
("Warranty")
Thank you for purchasing this Motorola branded product manufactured under
license by Binatone Electronics International LTD ("BINATONE").
What Does this Warranty Cover?
Subject to the exclusions contained below, BINATONE warrants that this
Motorola branded product ("Product") or certified accessory ("Accessory") sold
for use with this product that it manufactured to be free from defects in materials
and workmanship under normal consumer usage for the period outlined below.
This Warranty is your exclusive warranty and is not transferable.
Who is covered?
This Warranty extends only to the first consumer purchaser, and is not
transferable.
What will BINATONE do?
BINATONE or its authorised distributor at its option and within a commercially
reasonable time, will at no charge repair or replace any Products or Accessories
that do not conform to this Warranty. We may use functionally equivalent
reconditioned/ refurbished/ pre-owned or new Products, Accessories or parts.
General Information
21
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS
LIMITED WARRANTY, OTHERWISE THE REPAIR OR REPLACEMENT
PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE
REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED. IN NO EVENT SHALL MOTOROLA OR
BINATONE BE LIABLE, WHETHER IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF
THE PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT, INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF
REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE
ABILITY OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES TO THE
FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.
Some jurisdictions do not allow the limitation or exclusion of incidental or
consequential damages, or limitation on the length of an implied warranty, so
the above limitations or exclusions may not apply to you. This Warranty gives
you specific legal rights, and you may also have other rights that vary from one
jurisdiction to another.
22
General Information
Length of Coverage
One (1) year from the date of the
products original purchase by the first
consumer purchaser of the product.
Consumer Accessories
Ninety (90) days from the date of the
accessories original purchase by the first
consumer purchaser of the product.
Consumer Products and Accessories The balance of the original warranty or
that are Repaired or Replaced
for Ninety (90) days from the date
returned to the consumer, whichever is
longer.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and replacement of parts
due to normal wear and tear are excluded from coverage.
Batteries. Only batteries whose fully charged capacity falls below 80% of their
rated capacity and batteries that leak are covered by this Warranty.
Abuse & Misuse. Defects or damage that result from: (a) improper operation,
storage, misuse or abuse, accident or neglect, such as physical damage (cracks,
scratches, etc.) to the surface of the product resulting from misuse; (b) contact
with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the
like, extreme heat, or food; (c) use of the Products or Accessories for
commercial purposes or subjecting the Product or Accessory to abnormal
usage or conditions; or (d) other acts which are not the fault of MOTOROLA or
BINATONE, are excluded from coverage.
Use of Non-Motorola branded Products and Accessories. Defects or damage
that result from the use of Non-Motorola branded or certified Products or
Accessories or other peripheral equipment are excluded from coverage.
General Information
23
ENGLISH
Products Covered
Consumer Products
Unauthorised Service or Modification. Defects or damages resulting from
service, testing, adjustment, installation, maintenance, alteration, or
modification in any way by someone other than MOTOROLA, BINATONE or its
authorised service centres, are excluded from coverage.
Altered Products. Products or Accessories with (a) serial numbers or date tags
that have been removed, altered or obliterated; (b) broken seals or that show
evidence of tampering; (c) mismatched board serial numbers; or (d)
nonconforming or non-Motorola branded housings, or parts, are excluded from
coverage.
Communication Services. Defects, damages, or the failure of Products or
Accessories due to any communication service or signal you may subscribe to
or use with the Products or Accessories is excluded from coverage.
How to Obtain Warranty Service or Other Information?
To obtain service or information, please call:
UK
0844 557 0890
ROI 08187 62092
You will receive instructions on how to ship the Products or Accessories at your
expense and risk, to a BINATONE Authorised Repair Centre.
To obtain service, you must include: (a) the Product or Accessory; (b) the
original proof of purchase (receipt) which includes the date, place and seller of
the Product; (c) if a warranty card was included in your box, a completed
warranty card showing the serial number of the Product; (d) a written
description of the problem; and, most importantly; (e) your address and
telephone number.
These terms and conditions constitute the complete warranty agreement
between you and BINATONE regarding the Products or Accessories purchased
by you, and supersede any prior agreement or representations, including
representations made in any literature publications or promotional materials
issued by BINATONE or representations made by any agent, employee or staff
of BINATONE, that may have been made in connection with the said purchase.
24
General Information
ENGLISH
BINATONE TELECOM PLC
1 Apsley Way London NW2 7HF,United Kingdom.
Tel: +44(0) 20 8955 2700 Fax: +44(0) 20 8344 8877
e-mail: [email protected]
________________________________________
.
EC Declaration of Conformity
We the manufacturer / Importer :
Binatone Telecom Plc
1 Apsley Way London
NW2 7HF, United Kingdom.
Declare under our sole responsibility that the following product
Type of equipment:
Digital Video Baby Monitor
Model Name:
MBP36S, MBP36S-2, MBP36S-3, MBP36S-4
Country of Origin:
China
Brand:
Motorola
complies with the essential protection requirements of R&TTE Directive 1999/5/EC on the
approximation of the laws of the Member States relating to Radio Spectrum Matters, the
Council Directive /108/EC on the approximation of the laws of the Member States
relating to electromagnetic compatibility (EMC) and the European Community Directive
2006/95/EC relating to Electrical Safety. Directive 2011/65/EC on the restriction of use of
hazardous substances (RoHS) and 2009/125/EC relating to ecodesign requirement for
Energy-Related Products (ErP).
Assessment of compliance of the product with the requirements relating to the essential
requirements according to Article 3 R&TTE was based on Annex III of the Directive
1999/5/EC and the following standard:
Radio Spectrum:
EMC:
Electrical Safety:
RF Safety:
EN300328 V1.7.1 (2006-10), EN62311 (2008)
EN301489-17 V2.2.1 (2012-09),
EN301489-1 V1.9.2 (2011-09)
IEC60950-1:2005(Second Edition) + Am 1:2009
EN62311: 2008
The product is labelled with the European Approval Marking CE as show. Any UnauthoriVed
modification of the product voids this Declaration.
Manufacturer / Importer
(Signature of authoriVed person)
London, 20 April, 2014
Karl Heinz Mueller / Chief Technical Officer
General Information
Place & Date
25
Technical Specifications
Baby unit
Frequency
2.4 GHz to 2.48 GHz
Image sensor
colour CMOS 0.3M Pixels
Lens
f 2.5mm, F 2.8
IR LED
8 pcs
Power
Adapter: Ten Pao International Ltd.
S006MB0500100; Input: 100-240V,
50/60HZ 300mA; Output: 5.0V, 1000mA
OR
Adapter: Kuantech Incorporated Company
KSAS0050500100VKD; Input: 100-240V,
50/60Hz 300mA; Output: 5.0V, 1000mA
WARNING
Use only with supplied power supply.
26
General Information
Frequency
2.4 GHz to 2.48 GHz
Display
3.5" diagonal TFT LCD
Display colours
16.7M colour LCD
Brightness control
8 steps
Volume control
8 steps
Power
Adapter: Ten Pao International Ltd.
S003IB0500060; Input: 100-240V,
50/60Hz 150mA; Output: 5.0V, 600mA
ENGLISH
Parent unit (Model: MBP36SPU)
OR
Adapter: ShenZhen Frecom Electronic Co., LTD
F05W-050060SPAB
Input: 100-240V, 50/60Hz 150mA; Output: 5.0V,
600mA
WARNING
Use only with provided power supply.
Battery: GPI GPRHCH93C021 Ni-MH AAA 3.6V
900mAh rechargeable battery pack
OR
JUSTHIGH Ni-MH AAA 3.6V 900mAh rechargeable
battery pack
WARNING
Do not use non-rechargeable batteries for the Parent
Unit. Risk of explosion if battery is replaced by an
incorrect type. Dispose of used batteries according to
the instructions.
Specifications are subject to change without prior notice.
General Information
27
Manufactured, distributed or sold by
Binatone Electronics International LTD.,
official licensee for this product.
MOTOROLA and the Stylized M Logo,
are trademarks or registered trademarks
of Motorola Trademark Holdings, LLC.
and are used under license. All other
trademarks are the property of their
respective owners.
© 2014 Motorola Mobility LLC.
All rights reserved.
EN_UK Version 7.0
Printed in China
">