OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Copyright and Trademark

© Copyright 2014 KBL AG

This documentation only covers products manufactured by KBL AG. It must not be duplicated, photocopied, translated or stored without prior specifi c permission by KBL AG. Duplication on electronic media or in machinereadable form, either in whole or in part, is also prohibited.

is a registered trademark of KBL AG.

DISCLAIMER

All information given in this document correspond to the status quo at the date of publication but may be subject to changes. Therefore, we do not accept any liability for, nor do we guarantee the accuracy and/or completeness of the information.

EXPORT

Technical equipment and versions of the devices are in accordance with the legal prescriptions of the respective country of destination. Export to the USA and Canada of the KBL products, listed in this guide, or operation of the systems in these countries, are not permitted. KBL does not accept any manufacturers liability in case this direction is not adhered to. It is expressly pointed out that any violation of the export/operation prohibition will involve substantial risks of liability for the exporter and/or operator.

Version: BA_6808mod2013_GB_A

Date: 11/2014

Control / Software version: KBL-7 / 03.86

Item no: 0100036236

Device name [tech.]: 6808

For instruction updates, please refer to http://www.kbl-support.de.

KBL AG

Ringstrasse 24-26 · 56307 Dernbach · Germany

Telephone +49(0)2689.9426-0 · Fax +49(0)2689.9426-66

Email: [email protected] · www.megaSun.de

Contents

General information .............................................. 4

About these instructions ......................................... 4

Transport by forklift truck ........................................ 4

Other modes of transport ........................................ 4

Old equipment disposal .......................................... 4

Service ..................................................................... 4

Safety notes ........................................................... 5

Intended use ............................................................ 5

Duties of the operator ............................................. 5

Timer operation ....................................................... 5

General safety advice .............................................. 6

Tanning times .......................................................... 6

Updating the system software ................................ 6

Description of the unit .......................................... 7

Standards ................................................................ 7

Components ............................................................ 7

Connections ........................................................... 8

Connecting the mains voltage ................................. 8

Connecting an external audio source ..................... 8

Level adjustment studio music signal ..................... 8

Operation using different audio sources ................. 9

Bluetooth connection ............................................ 10

Connecting the channel selection ......................... 11

Connecting the external timer ............................... 12 aquaCool and Aroma connections ........................ 12

Start-up ................................................................ 13

Operating modes ................................................... 13

Tanning instructions ............................................ 14

Instructions for the user ........................................ 14

Tanning times ........................................................ 15

Tanning mode ...................................................... 16 preSelection .......................................................... 16

Starting the tanning session .................................. 18

Operation during the tanning session ................... 18

Basic functions ...................................................... 19

Variable section of the control panel ..................... 20

Standby mode / service mode ........................... 22

Layout of the display numbers .............................. 22

Switching the decorative lighting on and off ......... 22

Collagen boosters in standby mode ..................... 22 aquaCool spraying test ......................................... 22

Invoking the service menu ..................................... 22

Service menu - Basics .......................................... 23

Service menu - Overview ...................................... 25

PIN protection ....................................................... 26

Service menu - options ......................................... 26

Set decorative lighting ........................................... 39

Maintenance and cleaning ................................. 40

Instructions for cleaning and care ......................... 40

Maintenance intervals ........................................... 41

Tools and aids ....................................................... 41

Unlocking the bench ............................................. 42

Acrylic panes ......................................................... 42

Filter panes ............................................................ 44

Tubes ..................................................................... 45

P2 Tubes ................................................................ 45

Facial tanners ........................................................ 45

Shoulder tanner ..................................................... 46

Interior unit lighting ................................................ 47

Collagen boosters ................................................. 47

Filter cartridges ..................................................... 48

Canopy drive ......................................................... 48

Ventilation and air-conditioning ............................. 51

Recording to an SD card ....................................... 52

Replacing Aroma and aquaCool media................. 53

Replacing the aquaCool nozzles ........................... 53

System messages ............................................... 54

Technical data ...................................................... 56

Views ..................................................................... 56

O p e r a t i n g I n s t r u c t i o n s | megaSun 6700 - 6800 - 6900 3

General information

About these instructions

This operating manual is intended for use by

• operating staff,

• users,

• service staff.

Any person dealing with this tanning unit must have read and understood these instructions.

This manual describes units equipped with the maximum number of features.

Keep this manual ready to hand at all times.

Transport by forklift truck

The device is mounted on a pallet.

• Insert the forks carefully into the openings of the pallet.

• Lift the load by a few centimetres.

• Transport the load carefully to the place of installation.

Other modes of transport

DANGER

Overturning load!

Danger of being crushed by heavy parts of the equipment.

• Wear safety shoes.

Old equipment disposal

This device consists of components that cannot be thrown into the household garbage!

Dispose of your old equipment in an environmentally friendly manner after the end of its useful life. Metals and plastics can be recycled. Electrical and electronic components must be disposed of as e-waste.

Fluorescent lamps must be dropped off at authorized collection points for pollutants.

This helps to avoid damaging effects to the environment and human health caused by improper disposal.

This makes a valuable contribution to recycling and other forms of utilization of old electrical and electronic equipment.

You can obtain information about environmentally friendly disposal from your local government or the municipal administrations.

Service

For all service-related questions, please contact your responsible specialist dealer.

If a forklift truck cannot be used for transport, the box must be unpacked and the parts inside must be transported individually to the place of installation, e.g. using a dolly. Depending on the weight of the components, lifting them might require several people.

4

O p e r a t i n g I n s t r u c t i o n s | megaSun 6700 - 6800 - 6900

Safety notes

This chapter provides a summary of general information on safety and proper handling of the device.

More specifi c safety advice is given in other chapters of the operating manual.

Intended use

The unit is intended to be used for the tanning of one single person at a time. This person must not fall in one of the categories mentioned below, otherwise using the tanning equipment is prohibited for him or her.

The following individuals must not use the tanning system:

• Persons under 18 years of age.

• Persons with heart pacemakers.

• Persons, who are suffering or have suffered from skin cancer or have a predisposition toward this, or those whose fi rst-degree relatives are suffering or have suffered from malignant melanoma (black skin cancer).

• Persons taking photosensitive medications.

• Persons, who are being treated by a physician for conditions associated with photosensitivity.

• Persons suffering from acute sunburn.

• Persons, who are prone to freckles.

• Persons with atypical discoloured skin areas or/ and with more than fi ve atypical moles with a diameter of 5 millimetres or more and persons with more than 16 moles with a diameter greater than or equal to 2 millimetres. If in doubt, consult a physician!

• Persons, who had several severe sunburns as children.

• Persons with naturally red skin colour.

• Persons, who do not tan at all or cannot tan without getting sunburn.

• Persons, who have a predisposition toward sunburn.

Furthermore, this tanning unit has been designed for use by individuals who are in full command of their physical, sensorial and mental faculties. Moreover, suffi cient knowledge and experience are required.

During the operation no other persons shell be in the radiation range of the device.

Children, should be supervised to make sure that they do not use the unit as a toy.

Duties of the operator

KBL AG cannot be held liable for any damage resulting from improper use of the equipment or non-observance of these operating instructions.

Only use original replacement parts!

Only replace tubes and high pressure lamps with those listed on the device. Otherwise, this voids the operating authorization and warranty!

Timer operation

The tanning unit must be controlled via an external timer. Should the external timer fail, an internal timer will switch off the system automatically after 44 minutes.


General safety advice

• Follow all instructions given in this manual. In addition, observe all relevant statutory provisions and regulations, also those applicable in the country of operation.

• The unit must only be installed and assembled by specifi cally trained staff.

• Arbitrary modifi cations or conversions of the equipment are not permissible.

• Observe all danger signs and safety notices attached to the equipment.

• Safety notices must not be removed, and safety equipment must not be disabled or removed.

• The unit must only be operated when in perfect working condition.

• Never operate the unit with the outer covers or acrylic panes removed.

• The tanning system must be controlled via a timer that complies with the generally applicable standards.

• Absolutely observe the maintenance frequencies indicated in the maintenance plan.

• Pay attention to the load limit of the bench pane

(tanning bed units only).

• The bench must only be opened with bench pane folded down.

Updating the system software

ATTENTION

Risk of damage by switching off the power supply voltage.

Disconnecting power supply during the update process, will lead to damage of electronic components.

• Make sure that the unit is not disconnected from the power supply voltage during the update.

To accomplish the update download the “USB-

Connect” software offered by KBL. For detailed information press the help-button in the main menu.

Tanning times

Adhering to tanning times and schedules is essential.

6


Description of the unit

Standards

This tanning system complies with the following standards in their respectively applicable version:

• EN 60335-2-27

• EMC 2004/108/EC

• Low Voltage Directive 2006/95/EC

Components

The tanning unit basically consists of the following components:

• The canopy including 20 tubes, 3 facial tanners,

40 collagen boosters, preSelection- and interior display.

• The side part including 6 tubes and face tanner.

• The base part including 20 tubes and the electronic unit. Depending on the model also with shoulder tanner and further, optionally available components.

megaSun 6900 alpha deluxe

⑭

4

5

6

1

2

3

7 aquaCool - nozzles (optional equipment) preSelection display with USB connector

Collagen booster

Interior display

Facial tanner

Shoulder tanner (optional equipment)

Line connectors (In/Out)

(Player/Headset)

8 Base (faceplate)

9 Bench pane

10 Collagen tubes

11 Side pane

12 Canopy pane

13 Air nozzles

14 Canopy

① ② ③

④

⑬

⑤

⑫

⑥

⑪

⑩ ⑨ ⑧

⑦


Connections

Connecting the mains voltage

DANGER

Live parts

Risk of fatal injury due to electric shock when touching live parts.

• Disconnect from mains and secure against reconnection!

Both the power supply and the related connection work must comply with national standards, e.g. those set up by VDE in Germany. The connection work must only be performed by qualifi ed expert staff.

The connection to the 400 V mains must be protected by fuses. Their specifi cations are listed in the chapter

“Technical data”.

A residual current-operated circuit breaker (RCD) with short time delay is absolutely required. KBL AG recommends the following type: KBL 3200 0770 00

(type (Typ ABB F 204 A - 40//0,03 AP-R).

Should the operation of the tanning unit cause any interference in the power supply network, e.g. with ripple-control systems (TRA), consult your power supply company to have corresponding blocking elements (audio frequency suppressors) installed.

Connecting an external audio source

When connecting an external audio source (studio music), pay attention to the correct polarity.

Level adjustment studio music signal

The voice / audio system components are built in the middle of the bench part (vacuum housing) of the sunbed. The potentiometer which serves of the external audio signal is located on the left side of the housing. To avoid overdrive, select the level adjustment accordingly. The level setting depends on the strength of the external signal and should be carried out by a service engineer. Adjustment of the sound level can only be conducted in the service menu.

8


Operation using different audio sources

The tanning unit can be operated using the following audio sources:

• An internal audio source

• Various external audio sources

• All available audio sources

The audio source can be chosen in advance via the

“preSelection” feature and then changed at any time by using the interior control panel.

INTERNAL MP3 PLAYER

When using the internal MP3 player, you can either play the music tracks that are originally supplied on the SD card, or you can record your own tracks to the SD card.

EXTERNAL AUDIO SOURCES

LINE-IN

As an external audio source, you can connect devices ranging from the standard-line level to low loudspeaker levels.

These sources comprise:

• Studio music

• External players such as MP3 players, mobile phones (cell phones), I-pods, etc.

USB

You can connect a USB stick to a USB port that is integrated in the canopy.

EXTERNAL 100 V AUDIO SIGNAL (OPTIONAL

FEATURE)

If you decide for a connection to a 100 V audio system, you will need a transformer (KBL no.: 9100

0170 00) for the transmission of the audio signal.

This connection must be made by trained service staff.

EXTERNAL PLAYERS & HEAD-/EARPHONES

A line connection has been integrated on the righthand side of the bench’s head end so that the sunbed user can connect his or her own player such as an

MP3 player, an iPod, etc. Take hold of the jack plug and pull the cable out of the opening. Then connect the jack plug to the earphone jack of your player.

Then select ”MP3 ext.” as the audio source from the control panel of the sunbed before you start playing your own tracks from the player. For devices with bluetooth playback starts automatically.

The tracks can only be selected via the user’s own player. The volume can be controlled via the control panel of the sunbed and also via the corresponding operating elements provided by the user’s player.

Either a headphone or an earphone with a 6.3 mm jack plug can be used. The corresponding connector socket is located next to the line connector. The audio signal is switched over automatically.

MP3

ATTENTION

• Danger of damage to the player due to overheating.

• Do not place your player within areas that are directly exposed to UV radiation.


USB INTERFACE

The canopy of your sunbed is equipped with a USB connector socket. So you can also use a USB stick to play MP3 audio fi les. Just plug in your USB stick, and the sunbed will automatically play the tracks available on the stick when the tanning session starts. The

MP3 tracks to be played must not exceed a sampling rate of 320 Kbit/s.

KBL AG attaches great importance to hardware compatibility. Due to the large number of manufacturers of storage media, however, we cannot guarantee a 100 % compatibility. In rare cases, it may happen that a USB stick is not identifi ed correctly. If this happens, please use another USB stick.

Bluetooth connection

To connect an external player (smartphone etc.) wirelessly to the solarium an optional Bluetooth interface is available.

CONNECT EXTERNAL PLAYER

A Bluetooth connection can be established in standby and during tanning mode.

Make sure that you are within the reception area (about 2 meters).

Make sure that your device is confi gured to search for other bluetooth devices.

Should this not be the case, enable bluetooth manually. To do so, please read the instructions for your appliance.

• Depending on your settings the search will be performed automatically or manually. All available bluetooth devices within reach will be listed after a short time.

• Among the available devices choose “megaSun”.

In the service menu, a trailing number (01, 02, 03,

...) can be added to device name.

• If necessary confi rm the shown code and connect again. Not every smart phone asks for a code.

Make sure not to use any mass memory device other than a USB stick at this connection (see table “Technical Data”).

USB sticks that are equipped with an integrated

MP3 player have non-standard sector sizes.

We cannot guarantee the proper functioning of these sticks connected via the USB interface. So please use the line connection at the head end of the bench part for this type of device.

10


megaSun 01

megaSun 01

• A two-time beep indicates that your device is connected to the solarium.

Connecting the channel selection

The following diagrams show the wiring of the channel selection on the audio equipment’s side, for pulse coding as well as for BCD coding.

megaSun 01

megaSun 01

• Set your device to a medium volume level and start the music.

• Adjust the volume level on your device.

• During the tanning session, the volume control has to be done at the tanning device.

DISCONNECT EXTERNAL PLAYER

An existing connection is disconnected automatically after tanning.

The connection is automatically disconnected if the tanning session is not started within 6 minutes.

COMPATIBILITY OF BLUETOOTH DEVICES

KBL AG attaches great importance to hardware compatibility. Due to the large number of manufacturers,

KBL can not guarantee a 100 % compatibility. In rare cases, it may happen that a bluetooth connection can not be established.

CORRECTIVE ACTION

Each unit offers a list of paired devices. Delete the older entries in this list which have a profi le that overlaps with the ones for which you want to pair your device.

Start the bluetooth device detection again.

CHANNEL

1

2

3

6

7

4

5

8

BCD 0

0

1

0

1

0

1

0

1

BCD 1

0

0

1

0

1

1

0

1

BCD 2

0

0

0

1

1

0

1

1


Connecting the external timer

Connect the external timer (coin box, studio control) according to the instructions supplied with the timer.

The following diagram shows the wiring requirements with regard to the timer. The door contact is required if you have opted for the booth-scenting feature.

AROMA

The Aroma box is attached within the aquaCool box and equipped with three hose connections, one for the compressed-air supply

⑤ and two leading to the

Aroma nozzles

⑥

.

⑥

⑤

⑥

aquaCool and Aroma connections

AQUACOOL

The aquaCool box is equipped with a liquidlevel sensor

①

as well as with a connection to the aquaCool canister

②

. Furthermore, the box houses the compressor ensuring the compressedair supply

③

, and the Aroma box

④

with its related connections.

5

6

Aroma box (inlet)

Aroma box (outlets)

② ③

④

1

2

3

4

①

Connector (liquid-level monitoring)

Connection to aquaCool canister

Compressor with compressed air connection

Aroma box

12


Start-up

Before switching on for the fi rst time:

• Fix the supplied warning sign or one with the following wording permanently to the wall close to the tanning unit:

Warning!

• UV-radiation can cause eye and skin damage as well as skin aging and possibly skin cancer.

Ask the studio staff for further information.

• Wear protective goggles.

• Certain medicines or cosmetics can increase the sensitivity of the skin to UV radiation. If in doubt, consult a physician.

TANNING MODE

The tubes and the tanning lamps are switched on and a tanning session is in progress. While the unit is in tanning mode, the settings for the ongoing tanning session can be changed via the control panel.

SERVICE MODE

In the service mode, the device is confi gured for the tanning mode. Various values can be displayed and test functions can be carried out.

FAN RUN-ON

After the tanning session, the fan runs on for 3 minutes in order to cool down the device. The fan power is automatically decreased as the tubes cool down.

• Determine the presetting for the device in the service menu.

• Check correct installation of fl uorescent tubes.

The tube labeling must be visible, otherwise no tanning effect may be obtained.

• Store these Operating Instructions in a place that allows for easy access at any time.

Operating modes

The three different operating modes are explained below:

STANDBY MODE

The unit is in an idle state, i.e. it is connected to the mains but is currently not being used. The tubes and the tanning lamps are switched off. From the standby mode, you can change over to the tanning mode or to the service mode.


Tanning instructions

As a rule, an averagely tanning skin has achieved a uniform tan after three to fi ve tanning sessions.

These sessions should take place every second day.

To preserve the suntan achieved, one or two tanning sessions per week are normally suffi cient.

Instructions for the user

Observe the following tanning instructions:

NO SUNSCREEN WITH PROTECTION FACTOR

Sunscreens with sun protection factors are unsuitable for use in a tanning salon. For tanning, the skin should have been thoroughly cleaned and be dry. For optimum skin care, we recommend using our bodycare products after tanning.

GENERAL

• Any person that complies with the requirements laid down in the chapter “Intended use” may use the device.

• Never exceed your personal minimum erythema dose (MED). Follow the prescribed exposure times.

• If reddening of the skin (erythema) occurs hours after tanning, temporarily stop tanning. After a week the tanning can be resumed at the beginning of the tanning table.

• If unexpected effects (such as itching) occur within

48 hours after the fi rst tanning session, you should consult a physician before tanning again.

• Once fi nal tanning has been achieved, additional tanning is only possible by greatly exceeding the permissible tanning times. It is essential to avoid this.

• UV-radiation from the sun or from UV-devices can cause irreversible skin or eye damage. These biological effects depend on the type and amount of radiation as well as on the individual sensitivity of the skin.

• In cases of pronounced individual sensitivity or allergic reactions to UV-radiation, a physician should be consulted before beginning tanning.

• After excessive exposure to radiation, the skin may exhibit sunburn. Excessively repeated exposure to

UV radiation of sunlight or UV appliances can result in premature ageing of the skin and in a higher risk of skin cancer.

• The unprotected eye can suffer from surface infl ammation, and in certain cases, e.g. after a cataract operation, excessive radiation can damage the retina. After many repeated sessions, a cataract may form.

• Seek medical advice if persistent swellings or sores develop on the skin or if pigmented moles change in appearance.

• Only use radiation appliances of UV type 4 after consulting a doctor.

FOR EACH TANNING SESSION

• Always wear the supplied protective goggles.

Contact lenses or sunglasses are no substitute for the protective goggles!

• Remove cosmetics before tanning and do not use any sunscreen, or products that accelerate tanning.

• Allow for at least 48 hours to pass between sessions.

• After a tanning session in a studio, do not take another sunbath out of doors on the same day

• Protect sensitive areas, such as scars, tattoos, and genitalia, from radiation.

14


Tanning times

Please refer to the following tables for learning the individually applicable tanning times that depend on the skin type. For the precise defi nition of the skin types, please refer to the supplied skin-type table. If the tanning session sequence is interrupted for 4 weeks or more, you will have to start with the fi rst session again.

The interval between two tanning sessions must be at least 48 hours.

The times mentioned in the tanning schedules only apply on the condition that tubes are replaced according to the maintenance intervals stipulated in the section dealing with maintenance.

EU TANNING SCHEDULE - according to UV-Type III and 0,3W/m 2 in compliance with EN 60335-2-27

Skin type

1. Session

2. Session

3. Session

4. Session

5. Session

6. Session

7. Session

8. Session

9. Session

10. Session

I

6 min

6 min

7 min

7 min

8 min

9 min

9 min

10 min

10 min

11 min

II

6 min

7 min

7 min

8 min

9 min

10 min

11 min

12 min

13 min

14 min

Max. number of tanning sessions per year

6900 alpha deluxe intelliSun

All other devices

-> 6700; 6800

63

90

50

71

III

6 min

7 min

9 min

10 min

12 min

13 min

15 min

16 min

18 min

19 min

37

52

IV

6 min

8 min

10 min

12 min

14 min

16 min

19 min

21 min

23 min

25 min

28

40

V

6 min

10 min

14 min

19 min

23 min

27 min

32 min

36 min

40 min

44 min

16

23

VI

6 min

11 min

17 min

22 min

28 min

33 min

39 min

44 min

50 min

> 55 min

13

18


Tanning mode

DANGER

Excessive dose of UV radiation

Excessively prolonged tanning sessions may cause severe damage to skin and eyes.

• Never operate the solarium with a defective timer.

• Observe the tanning times given in the tanning schedule.

There is a preSelection control panel in the middle of the front part of the canopy.

Depending on the confi guration of the sunbed, up to seven control buttons are available for you to make your choice.

Your choice remains stored for 3 minutes.

If you do not start your tanning session within this time, the system is reset to the default values defi ned in the service menu.

The following explanations and functions refer to a tanning system that is fully equipped with all features.

preSelection

Before starting your tanning session, the preSelection feature allows you to choose certain tanning options in advance.

Simply select your preferences and enjoy your tanning session from the very beginning.

The preSelection options are divided into three differently coloured groups.

RED BLUE

Preselection of the audio source

GREEN

Preselection of other features

16


p r e S e l e c t i o n m e n u

Preselecting the tanning level

Optimum tanning conditions suited to meet the requirements of individually different pretan levels are achieved by specifi cally adapting the UV spectrum.

Use the three buttons BASIC,

MEDIT. and CARIBIC to choose the setting that matches your individual level of skin pigmentation.

The option of preselecting the tanning level is only available with intelliSun!

Preselecting the audio source

You can preselect one out of three different audio sources.

During the tanning session, you can change the audio source at any time via the interior display.

MP3 int.

MP3 INTERNAL

You will listen to the tracks played by the internal MP3 player of the sunbed during the tanning session.

BASIC

BASIC

Equal proportions of UV-A and UV-B produce a balanced tanning effect.

MEDIT.

MEDITERRANEAN

A higher proportion of UV-A results in faster tanning.

MP3 ext.

MP3 EXTERNAL

You can plug in your own player into the line-in headphone jack at the head end of the sunbed.

CARIBIC

CARIBIC

A higher proportion of UV-B helps the user achieve a more intense tan.

STUDIO

STUDIO MUSIC

You will listen to the music that is externally provided by the studio operator.

Preselecting other features

This group provides you with further features to choose from. Each of the features can be activated or deactivated by pressing the corresponding touch button.

VOICE

MEGAVOICE

Switches the voice guidance on or off.

AIRCON

AIRCONDITIONING

Switches the air-conditioning unit on or off.

AROMA

AROMA

Switches the Aroma function on or off.

AQUA

AQUACOOL

Switches the aquaCool function on or off.

Status of the symbols (example)

Active brightly.

Inactive dimmed.

If the option is not available, or has not been activated in the service menu, the fi eld remains black.

options options shine are

NOTES:

• During the fan run-on, the preSelection menu is blocked.

• The default settings of the preSelection menu can be determined in the service menu.


Starting the tanning session

The tanning session will commence automatically after the warm-up time controlled by the timer has elapsed. During the warm-up time, the tanning session can be started manually at any time by pressing the START button.

Operation during the tanning session

You can control the functions of the sunbed via the interior display during the tanning session. It is particularly easy for you to access the basic functions.

Additionally, you can also change the preSelection settings by using the interior display.

Buttons with recesses that can easily be sensed allow for easy operation of the system even with your eyes closed.

+

/

-

BUTTONS

• Control the functions.

ARROW BUTTONS

• Select the preSelection functions.

NOTES:

20 seconds after your last input, the display changes over to the indication of the tanning time.

An information line at the bottom edge of the display informs you about currently selected features.

Position

Recessed button

STOP BUTTON

• Stops the tanning session if pressed for at least two seconds.

05:23

DISPLAY

• Shows the menu items and functions.

• Indicates the tanning time.

• Information line

START BUTTON

• Starts the tanning session during the warm-up time

• as well as after an interruption caused by pressing the STOP button, provided that the booked tanning time has not elapsed yet.

18


During the tanning session, you need quick access to basic functions such as volume control, body fan and facial tanners.

You should also be in a position to change your preselected settings.

The control panel caters for both requirements. You have

• direct access to frequently needed functions via the “Basic functions” section, and

• access to the presetting you made via the preSelection menu (display according to the rotation principle).

Basic functions section

Variable section of the control panel

(preSelection functions)

Basic functions

max/on

Volume

II

Facial tanner

I

Keep pressed for 2 seconds

Remark on facial tanner operation:

For safety reasons, the facial tanner, once switched off, cannot minutes have elapsed.

Body fan be switched on again before three

The body fan is automatically controlled by ACS. As

If you try to activate the facial tanner soon as you press one of during this time, your command the fan buttons, the autowill be stored, and the tanner will matic mode is interrupted.

be switched on automatically after a delay, i.e. after the blocking time has elapsed.

Keep pressed for 2 seconds min/off



During the tanning session, you continue to have access to the settings you have made via the “preSelection” function. If you wish to make any changes to your choice, you can do so in the variable section of the control panel. By pressing one of the arrow buttons , above or below the changeover symbol functions will be displayed one after the other according to the rotation principle.

, all available

You can switch these individual functions on or off and, if possible, make changes to the settings.

Selectable function symbols (for a fully equipped unit).

preSelection)

MP3-int. Studio MP3-ext. USB

Collagen aquaCool Aroma megaVoice

Aircon on

Air-conditioning

After the air-conditioning system has been switched off, it cannot be restarted for three minutes for safety reasons. If the system is switched on during this time, the command will be stored. The air-conditioning system will be switched on automatically after a delay, i.e. after the blocking time has elapsed. If the condensate canister is full, the following symbol fl ashes on the display: aquaCool

An ongoing spraying process cannot be stopped. If the aquaCool supply is running low, a corresponding message is displayed in the standby mode. After the message has appeared for the fi rst time, the aquaCool supply will last for approximately another 2.5 hours of operation. If the system has run out of aquaCool liquid, the aquaCool function is deactivated automatically, and the symbol shown below is displayed.

III

II

I

Collagen booster

Aroma megaVoice off

See also the chapter

“Maintenance/Airconditioning system”.

aquaCool is automatically re-activated as soon as a full canister has been connected.

0

20


AUDIO FUNCTIONS

There is a maximum of four audio sources available at the user’s disposal. If you change over to another source, you must activate it fi rst. The activation is effected by pressing the or the button (with the exception of USB audio). All inactive audio functions are marked with “OFF” on the display so that you can easily recognise the active audio source.

S

E

L

E

C

T

MODEL: ACTIVATING AUDIO FUNCTIONS


(audio functions)

Channel

Studio

ACTIVATE

MP3 external (AUX)

This function is used to play the studio music.

If the Studio function has been activated, you can press the plus and minus buttons to browse through the channels, provided that more than one channel is available.

Channel

MP3 internal

Tracks

The right-hand side of the sundbed’s head end is equipped with a cable with a 3.5 mm jack plug so that you can make use of external players, such as MP3 players, iPods, etc. In this way, you can connect the headphone jack of your player to the tanning system.

Use the corresponding operating elements of the external player in order to select the desired tracks.

With the “MP3 external” control element you have also access to a Bluetooth connected device.

USB-Audio

This function is used to play the tracks of the internal

MP3 player of the tanning unit.

If the MP3 internal function has been activated, press the plus and minus buttons to browse through the individual tracks.

USB is automatically activated as soon as a storage medium is connected to the USB port. This USB port is located above the exterior display (see overview on page 7).

If you change the audio source later on, please note that you must re-activate USB before you can use it again. While USB is active, use the plus and minus buttons to select individual tracks. With a

USB stick connected, all other audio symbols of the preSelection menu are inactive.

Tracks


Standby mode / service mode

While the tanning unit is in standby mode, you can switch the decorative lighting of the sunbed on and off and trigger an aquaCool spraying test (1 spraying cycle).

When the unit is in service mode, you can make the presettings for operation in tanning mode, and you can have values concerning the operation of the sunbed displayed.

Layout of the display numbers

The buttons of the interior display are allocated double functions. In addition to the standard operating elements, they stand for numbers that, in standby mode, provide access to standby and service functions. Simply enter the corresponding sequence of numbers on the display.

Switching the decorative lighting on and off

5 0 5

NOTE

The connection times of the decorative lighting can be set in the service menu individually for each day of the week.

There are two independent connection periods (A and B) available for each day of the week.

Collagen boosters in standby mode

In standby mode, the collagen boosters work as decorative lighting with minimum power. For testing and demonstration purposes the three operating modes can be activated via the control panel. After 10 seconds, the boosters automatically switch back to the decorative mode.

aquaCool spraying test

4 9 4

1 2 3 4 5

6 7 8 9 0

Invoking the service menu

1 6 1 0 0 0 0

PIN

NOTE

Do not let too much time pass between the individual keystrokes when entering a sequence of numbers!

22


Service menu - Basics

In standby mode, the service level is accessed by entering “161”, followed by PIN “0000”. There is one additional condition that must be fulfi lled:

• No incoming signal from the coin-box system.

SERVICE MENU - STANDARD OPERATING

ELEMENTS

After having entered the service PIN, the service menu is at your disposal. Navigation is made via the following buttons (see also chapter: Layout of the display numbers):

• Use buttons 4 (UP) and 9 (DOWN) to browse through the individual menu items and functions.

• Press the START/ENTER button to go to the corresponding submenu.

• Button 2 and 7 are used to switch functions on and off and to modify values.

• Press 3 (STORE) to save all modifi cations made in all menu items.

• Press 8 (EXIT) to go back to the previous menu level or to exit the service menu.

+/ON STORE UP

② ③ ④

SERVICE MENU - BASIC OPERATION

The service menu is divided into the main menu and subordinate groups of functions.

If you choose a menu item, e.g. “AUDIO”, you will get access to all functions related to this item.

MAIN MENÜ

4

Select the desired function group from the main menu by pressing the 4 (UP) or the 9 (DOWN) button.

The currently selected group is highlighted.

9

• Press the START/ENTER button to access the desired group menu.

RESET

R

E

S

E

T

⑦

-/OFF

⑧

EXIT

⑨

DOWN

ENTER

• The currently active function (circle) is displayed in the centre line on the left-hand side. You can invoke further functions of this group by pressing

4 (UP) or 9 (DOWN).

Function group

Group number

4

Function

9

Settings


CHANGE SETTINGS

• Depending on the respective function, you can change values, select options and switch functions on or off.

To do so, use the buttons 2

(+) and 7 (-).

2

Example:

Changing a value

+1min

STORE & EXIT

• Save your settings by pressing the button 3

(STORE). If you fail to do so, the system will not take over the changes you made. -> See also chapter “Service Menu - Timeout”.

• By pressing the STORE button, you save all changes you have made in all menu items.

3

-1min

7

> German

2

Example:

Selecting an option

• By pressing 8 (EXIT), you go back to the previous menu level, or you exit the service menu.

> English

7

8

> ON

2

> OFF

7

Example:

Switching a function on/off

SERVICE MENU - TIMEOUT

After performing your last operating action, you have

2 minutes left to save the changes you have made.

Then, a prompt appears and all changes are automatically discarded after an additional 20 seconds.

SERVICE MENU - AUDIBLE SIGNALS

For user convenience, operation and storage processes are acoustically acknowledged in different ways:

Operation process

Storage process

->

-> short sound long sound

24


KBL-7

Service menu - Overview

ENVIRONMENT

Language ①

Contrast ②

TIME AND DATE ③

TIMER DECORATIVE LIGHTING ④

Maximum tanning time ⑤

HOUR METERS

Operating hours overall ⑥

Operating hours tubes ⑦

Operating hours facial tanner ⑧

Number of sunbaths ⑨

PRESELECT

UV-Typ ⑩

Audio ⑪

Voice (megaVoice) ⑫

Aircon (aircondition) ⑬

Aroma ⑭

Aqua (aquaCool) ⑮

AUDIO

MP3 internal ⑯ megaVoice ⑰ megaVoice language ⑱

Studio Line-in ⑲ usb MP3 ⑳

MP3 external (Line in)

Studio channel selection

Number of studio channels

Music nonstop

Nonstop music source

Default volume tanning

Default volume standby

Maximum adjustable volume megaVoice volume adaption

Dynamic volume adaption

Treble MP3 - USB

High bass MP3 - USB

Low bass MP3 - USB

Volume adaption Studio Line-In

Treble Studio Line-In

High bass Studio Line-in

Low bass Studio Line-In

AQUA aquaCool aquaCool spray time

Cycle time aquaCool start test cycle aquaCool endurance test aquaCool start initialization

VERSION: 03.86

AROMA

Aroma

Aroma status reset

Cycle time

Aroma cabin automatic

Aroma cycles per hour

TIMER AROMA

Aroma start test cycle

AIR CONDITIONING

Air condition

Start level body fan

RGB

RGB mode

EASYCARE

SETTINGS easyCare mode only (EConly) man. time confi g (T.Display) easyCare tanning time

Adjust

Set value quicktest

Melanin min value

Melanin min runtime

Sensor-check

Volume

UV-LEVEL

SERVICE

Load factory defaults

Personal PIN

BLUETOOTH

Name

Powerlevel

FIRMWARE-TYP

FIRMWARE-VERSIONS

SOFTWARE UPLOAD

RGB-Setup

SERVICE MODE

Service mode without tanning

Service mode with tanning

SOLARIUM IDENTIFICATION

SOLARIUM X-CODE

Reboot

EVENT LOG


PIN protection

In delivery condition some menu items are protected by a factory “PIN”. Optionally, the factory “PIN” can be replaced by a personal “PIN”.

• You will receive the personal “PIN” with the product documentation.

• The personal “PIN” may be activated or deactivated by selecting the “SERVICE/Personal PIN” setting in the service menu.

Service menu - options

• In order to avoid operating errors, read through the basics at the beginning of the “Service Menu” section.

• Always remember to save your settings by pressing

STORE.

• All menu items that comprise further submenus are displayed in CAPITAL LETTERS.

Every software update deactivates the personal “PIN”.

Personal ”PIN” protected menu items may be identifi ed by the personal “PIN” logo as given in the service menu.

①

> German

> English

ENVIRONMENT

Language

>

Sets the language of the menu.

Factory setting : German

②

ENVIRONMENT

> 00000.. . 00030

Contrast

>

Sets the contrast of the display.

Factory setting : 00020

01/05

02/05

26


③

ENVIRONMENT

TIME AND DATE

> press ENTER

03/05

Entry of date and time. Invoke the submenu by pressing START (ENTER).

The menu item „Timer decorative lighting“ offers you two switching cycles (A and B) for each day of the week.

NOTE - SWITCHING CYCLES

Using the setting „monday-sunday“, the switching cycle will be the same for each day of the week.

SUBMENU

TIME & DATE

ENVIRONMENT\TIME & DATE 01/02

Time

>

Select input fi elds

(start / set)

ENVIRONMENT\TIME & DATE 02/02

Date

>

Week

Monday

- Sunday

Day

Monday

Tuesday

Wednesday

Thursday

Friday

Saturday

Sunday

Switching cycle

A

A-ON

A-OFF

B

B-ON

B-OFF

Switching cycles

A B

A-ON B-ON

A-OFF

A-ON

B-OFF

B-ON

A-OFF

A-ON

A-OFF

A-ON

A-OFF

A-ON

A-OFF

A-ON

A-OFF

A-ON

A-OFF

B-OFF

B-ON

B-OFF

B-ON

B-OFF

B-ON

B-OFF

B-ON

B-OFF

B-ON

B-OFF

Friday

Switching cycle A Switching cycle B

A

ON

08:30

A

OFF

12:00

B

ON

14:30

B

OFF

22:00


④

ENVIRONMENT

TIMER DEKOLIGHT

> press ENTER

04/05

Entering switching times for the decorative lighting.

The submenu is invoked by pressing START (ENTER).

⑤

> 5min .. . 45min

>

ENVIRONMENT

Maximum tanning time

05/05

Sets the maximum tanning time for all timers. In the easyCare operating mode, the setting has been fi xed to 30 minutes.

Factory setting: 44 minutes

SUBMENU

TIMER DECOLIGTH

SELECT WEEK OR DAY OF THE WEEK

01/08

>

> Monday - Sunday > press ENTER

⑥

HOUR METERS

Operating hours overall

> 0788h

01/04

Displays the total operating hours.

ENTER SWITCHING TIME

> (Day) AON

> (Day) AOFF

> (Day) BON

> (Day) BOFF

>

⑦

> 0183h

HOUR METERS

Operating hours tubes

>

02/04

2 sec. = reset

Displays the total operating hours of the tubes and includes a reset function and set function to set the value in steps of fi ve via the +/- buttons.

• Save settings by pressing STORE!

SET SWITCHING CYCLES

> 00:00 - 23:59

>


1/04

+/- Set the time


⑧

> 0156h

HOUR METERS

Operating hours facial tanner

>

03/04

2 sec. = reset

Displays the total operating hours of the facial tanner and includes a reset function and set function to set the value in steps of fi ve via the +/- buttons.


28


⑨

HOUR METERS

Number of sunbaths

04/04

> 0000 Reset: press `-` for 2s

2 sec. = reset

Indicates the number of tanning sessions (sunbaths) and includes a reset function.

Under the menu item “ PRESELECTION” you can make the initial settings for the

“preSelection” functions. The functions must be available and activated in this service menu

⑯/⑰/⑲/ / / .

⑩

> Caribic

> Medit.

> Basic

PRESELECTION

UV-Typ

>

01/06

Determines the initial setting of the “preSelection” tanning level. Only available with intelliSun!

Factory setting: Basic

⑪

> Studio Line-In

>

> MP3-internal

> MP3-external

PRESELECTION

Audio

02/06

Determines the “preSelection” setting of the audio source.

Factory setting: MP3-internal

⑫

> on

> off

PRESELECTION

Voice (megaVoice)

>

03/06

Specifi es the “preSelection” setting of the voiceguidance system.

Factory setting: on

⑬

PRESELECTION

Aircon (Aircondition)

>

04/06

> on

> off

Fixes the “preSelection” setting of the airconditioning system.


⑭

Aroma

>

> on

> off

PRESELECTION

Defi nes the “preSelection” setting of Aroma.


⑮

Aqua (aquaCool)

>

PRESELECTION

> on

> off

05/06

06/06

Specifi es the “preSelection” setting of aquaCool.


⑯

> on

> off

AUDIO

Mp3-internal

>

01/22

Activates and deactivates the internal MP3 player.

Factory setting: off

⑰

> on

> off

AUDIO megaVoice

>

02/22

Activates and deactivates the voice-guidance system (megaVoice).



⑱

> English

> German

> ...

AUDIO megaVoice language

>

03/22

Fixes the language setting of the megaVoice system.

The following languages are fully supported:

GB,RU,DE,FR,IT,PL,CZ,NL,HU,BG,HR,RO,RS,SK

The following languages are supported in part:

DK,EE,LT,NO,ES,SE,TR (without easyCare)

Factory setting : Depending on the operator country

⑲

> on

> off

AUDIO

Studio Line-In

>

04/22

Activates and deactivates the Studio (line-in) audio signal.

Factory setting : on

⑳

> on

> off

AUDIO usb MP3

>

05/22

Activates and deactivates the USB interface

(canopy, above the outer display).


AUDIO

MP3 (Line-In)

>

06/22

> on

> off

Activates and deactivates the line-in connection

(bench part, right-hand side of the head end) for units from standard-line level to low loudspeaker levels (MP3 player, iPod, etc.).


AUDIO

Studio channel selection

>

07/22

> bcd

> puls code

> off

Allows for the change-over between pulse-code and BCD-code mode with the Studio music signal pending and deactivates the external-channel selection.

Factory setting : bcd

AUDIO

Number of studio channels

>

08/22

> 2

> 4

> 8

If bcd has been preselected, the number of channels available in the studio is specifi ed here.

Factory setting : 4

AUDIO

Music nonstop

>

09/22

> on

> off

If this function is active, music is played nonstop, i.e. also out of tanning sessions.

Factory setting : off

> MP3-internal

> Studio Line-In

>

AUDIO

Nonstop music source

10/22

Allows for choosing the permanent audio source for the “Music nonstop” function“.

Factory setting : MP3-internal

30


AUDIO

Default volume tanning

>

11/22

> 0 .. . 9

Sets the volume for the tanning mode.

Factory setting : 6

AUDIO

Default volume standby

>

12/22

> 0 .. . 9

Sets the volume for the standby mode.

Factory setting : 3

AUDIO

Maximum adjustable volume

>

13/22

> 5 .. . 9

Presetting the maximum adjustable sound level, limits the maximum adjustable sound level in the operating and standby mode.

Factory setting : 9

> -09 .. . +09 dB

>

AUDIO 14/22 megaVoice volume adaption

Here you can adapt the volume of megaVoice.

Factory setting : -07 dB

AUDIO

Dynamic volume adaption

>

> on

> off

Dynamic volume adaption on-/off.

15/22


> -14 .. . +14 dB

>

AUDIO

Treble MP3 - USB

Sets the treble for MP3 - USB operation.

16/22

Factory setting : +14 dB

> -14 .. . +14 dB

>

AUDIO

High-bass MP3 - USB

Sets the high-bass for MP3 - USB operation.

17/22


> -14 .. . +14 dB

>

AUDIO

Low-bass MP3-USB

Sets the low-bass for MP3 - USB operation.

18/22


> -29 .. . +29 dB

>

AUDIO 19/22

Volume adaption Studio Line-In

Here you can adapt the volume of studio line-in signal.


> -14 .. . +14 dB

>

AUDIO

Treble Studio Line-in

Sets the treble for studio music operation.

20/22



> -14 .. . +14 dB

>

AUDIO

High-bass Studio Line-in

21/22

Sets the high-bass for studio music operation.


> -14 .. . +14 dB

>

AUDIO

Low-bass Studio Line-in

22/22

Sets the low-bass for studio music operation.


AQUA aquaCool

01/06

> on

> off

Activates and deactivates the aquaCool function.


> 2 .. . 6 (sec)

AQUA aquaCool spray time

>

02/06

Determines the duration of the aquaCool spraying time.

Factory setting : 6

> 1 .. . 5 (min)

AQUA

Cycle time

>

03/06

Defi nes the aquaCool and aroma cycle time

(spraying time + spraying interval).

Factory setting : 1

AQUA

> Start: press `+` for 2s

04/06

Starts the aquaCool test (1 cycle).

AQUA aquaCool endurance test

>

05/06

> on

> off

Starts the aquaCool endurance test. After having selected and stored the “on” setting, you must leave the service menu and start a tanning session.

Attention! aquaCool will continue to spray permanently during a whole tanning session.


AQUA aquaCool initialization


Starts the aquaCool initialization process. A spraying cycle of 90 seconds is started to bleed the system before commissioning, after a repair operation or after a canister replacement.

AROMA

Aroma

01/07

> on

> off

Activates and deactivates the aroma function.


32


AROMA

Aromastatus reset

> Reset: press `-` for 2s

02/07

2 sec. = reset

Reset -> after having exchanged the Aroma tin.

The menu item „TIMER AROMA“ offers you a switching cycle for each day of the week.

NOTE - SWITCHING CYCLES

Using the setting „monday-sunday“, the switching cycle will be the same for each day of the week.

> 1 .. . 5 (min)

AROMA

Cycle time

>

Defi nes the aroma cycle time (spraying time + spraying interval). Only active in systems without aquaCool or disabled aquaCool.

Factory setting : 1

> Door contact >

> Intervall

> off

AROMA

Aroma cabin automatic


03/07

04/07

The cabinet scent release can be set at intervals, controlled by a door contact switch, or completely deactivated.

Week

Monday

- Sunday

Switching cycle

ON

OFF

Day

Monday

Tuesday

Wednesday

Thursday

Friday

Saturday

Sunday

Switching cycles

ON

ON

OFF

ON

OFF

ON

OFF

OFF

ON

OFF

ON

OFF

ON

OFF

Friday

Swichung cycle

ON

08:30

OFF

20:00

AROMA

Aroma cycles per hour

>

05/07

> 1 .. . 6

For interval operation of the cabinet scent released, the number of scent releases per hour can be set here.

Factory setting : 3


AROMA

TIMER AROMA

> press ENTER

Entering switching times for the Aroma Timer.

The submenu is invoked by pressing START (ENTER).

06/07

SUBMENU

TIMER AROMA

SELECT WEEK OR DAY OF THE WEEK

01/08

>

> Monday - Sunday > PRESS ENTER

AROMA

Aroma start testcycle


Starts the Aroma test (1 cycle).

AIR CONDITIONING

Aircon (air conditioning)

>

> on

> off

Switches the air-conditioning unit on and off.


01/02

ENTER SWITCHING TIME

> (Day) ON

> (Day) OFF

> Monday: OFF

AIR CONDITIONING

Start level body fan

>

02/02

> 1 .. . 9

Specifi es the “start speed” setting of the body fan at the beginning of the tanning.

Factory setting: 2

SET SWITCHING CYCLES

02/02

> 00:00 - 23:59

>


(start / set)

+/- Set the time


RGB

RGB mode

>

01/01

Not available in this system.

Note:

For devices with LED technology, the desired

RGB color mode is adjusted by the colorMotion controller.

34


The easyCare menu item is only available with CPI

Energy and intelliSun sunbeds that are connected to an easyCare system.

Submenu SETTINGS.

Invoked by pressing

START (ENTER).

EASYCARE

SETTINGS

> press ENTER

01/03

SUBMENU

EASYCARE SETTINGS easyCare mode only (EConly) man. time confi g (T.Display) easyCare tanning time

Adjust

Set value quicktest

Melanin min value

Melanin min runtime

EASYCARE\SETTINGS easyCare mode only (eonly)

>

01/07

> on-US

> on

> off

If this function is active, the tanning session is strictly carried out on the basis of the values determined by the easyCare system. The adjustment „on-US“ is required for operation in the United States.

Factory setting : Depending on the operator country

EASYCARE\SETTINGS man. time config (TDispl.)

>

02/07

> on

> off

If this function is active, the tanning time can be entered at the easyCare unit. The tanning power will be adapted automatically.


> 8min .. . 20min

>

EASYCARE\SETTINGS easyCare tanning time

03/07

Allows for preselecting the tanning time. The tanning power will be adapted automatically.

Factory setting : 20 min

> 1 .. . 7

EASYCARE\SETTINGS

Adjust

>

04/07

These settings must only be made by trained service personnel!

The default setting „1“ must not be changed.

> 150.. .300

EASYCARE\SETTINGS

Set value quicktest

>

05/07



> 0.. .400

EASYCARE\SETTINGS

Melanin min value

>

06/07


Factory setting: EU=0 / USA=100


EASYCARE\SETTINGS

Melanin min runtime

>

07/07

SERVICE

Load factory defaults

> Reset: press `-` for 2s

01/11

> 1.. .20


Factory setting : EU=10 / USA=6

Loads the factory (default) settings.

SERVICE

PERSONAL PIN

> press ENTER

02/11

EASYCARE

Sensor-Check

> 00000 performed by qualifi ed service staff!

02/03

Displays the current values during a melanin measurement.

This function is intended for sensor diagnosis to be

EASYCARE

Volume

>

03/03

> 0 .. . 9

Sets the volume of the easyCare voice-guidance system.


UV-LEVEL 01/01

SET UV-LEVEL

>

Submenu call with START/ENTER.

SUBMENU

SERVICE\PERSONAL PIN 01/01

ENTER SOLARIUM PERSONAL PIN

> PIN:

PERSONAL PIN activate / deactivate

Enter your personal PIN.

SERVICE

BLUETOOTH

> press ENTER

Submenu BLUETOOTH.

Invoked by pressing

START (ENTER).

03/11


Name

Powerlevel

SUBMENU

BLUETOOTH

36


SERVICE/BLUETOOTH

Name: KBL Sound

>

01/02

> 01 - 99

To fi t your Studio environment (multiple units) different numbers can be added to the bluetooth device name (megaSun xx ) of each solarium.

Factory setting : 01

SERVICE\BLUETOOTH

Powerlevel

>

> 1 .. . 7

Sets the transmission power for bluetooth.

Factory setting : 1

02/02

SERVICE

FIRMWARE-TYP

> press enter

04/11

Submenu call with START/ENTER. Displays the current fi rmware typ / variant.

SERVICE

FIRMWARE-VERSIONS

> press enter

05/11

Submenu call with START/ENTER. Displays the current fi rmware version of the system components.

Do not operate the system with different fi rmware versions!

• All system components must be equipped with an identical fi rmware version.

SERVICE

SOFTWARE UPLOAD

> press enter

06/11

Submenu call with START/ENTER. Displays the fi rst and the last Software-Upload.

SERVICE

RGB-Setup

>

Not available in this system.

Submenu SERVICE MODE.

Invoked by pressing

START (ENTER).

SERVICE

SERVICE MODE

> press ENTER

SUBMENU

SERVICE MODE



07/11

08/11

SERVICE 01/02


> Start: press `ENTER` for 2s

Troubleshooting mode.

The service mode is switched on for 30 minutes.

The mains voltage is connected. Error notifi cations are ignored, but tanning cannot be started.

SERVICE


02/02

> Start: press `ENTER` for 2s

Troubleshooting mode.

The service mode is switched on for 10 minutes.

The mains voltage is connected. Error notifi cations are ignored, tanning can be started. After this period, there is a 3 minute restart lockout.


SERVICE

SOLARIUM IDENTIFICATION

> press enter

09/11

Show the characteristics of the device:

- Confi guration code

- Variant code

- Serial number

EVENTLOG

>

01/01

SERVICE

SOLARIUM X-CODE

>

> PIN:

Branches to further confi guration options.

10/11


Lists the latest 99 events (error codes & infomessages). Detailed information is available by pressing the Start button.

Example: no. time date code tanning time

001 16:44 05.01.09 0011 03:23

002 15:22 05.01.09 0002 07:22

003 10:07 22.12.08 .... ....

004 17:16 ....

005 ....

....

099

SERVICE

Reboot

> Reboot: press `-` for 2s

11/11

Performs a restart of the electronics.

Attention

• All unsaved changes will be discarded!

38


Set decorative lighting

For remote control of the fourSeason color mode, you may use our colorMotion controller.

Available only for devices with LED technology.

colorMotion controller

Decorative lighting

On / Off

Program selection switch colorWheel

Brightness or frequency increase / decrease

To control the fourSeason color mode of the device use the stylish colorMotion controller with its elegant colorWheel and its full touch panel. Change brightness, turn on and off the lighting, select static colors or select one of the automatic color change programs. This wireless control technology allowes remote control from various directions with just a fi nger touch.

Low power consumption and awakening

After 20 sec. without touching the controller will automatically enter the low power sleep mode. Touch any key to wake up the controller to normal use.

Match code function

In order to control several devices with one

RF-controller press down the match code button on the LED controller and the “I” button at the

RF-controller at the same time, wait for the LED lamp fl ashing several times, then move away from the two buttons. To cancel match, press down the match code button on the LED controller and the “O” button at the RF-controller at the same time, wait for the LED lamp fl ashing several times, then move away from the two buttons. To do this, the service mode must be activated in the service menu at the tanning device.

The LED controller is located in the tray of the electronic box.

match code button colorMotion controller - control elements

On / Off

Decorative lighting.

The selected setting automatically will be saved when the system is switched off.

7

8

5

6

3

4

1

2

9

10

11

12

13

13

15

16

17

18

Program selection switch

Program Mode

RED

GREEN

BLUE

YELLOW

PURPLE

CYAN

WHITE

3 color - jump

7 color - jump

3 color - gradient

3 color - smooth

7 color - gradient

7 color - smooth

3 color - fl icker

7 color - fl icker

3 color - fl ash

7 color - fl ash

Auto play

Note

Intensity adjustable

Frequency adjustable

(Repetition rate) colorWheel

By touching the colorWheel the selected color switches on and additionally the program selection will be reset. At the next program selection, the program 1 (RED) will start.

Increases / decreases the intensity of the static colors (Program 1-7).

Increases / decreases the repetition rate

(Program 8-18).


Maintenance and cleaning

Regular maintenance is required for the safe operation of the tanning unit and must be documented.

Cleaning must be performed when necessary.

DANGER

Live parts

Risk of fatal injury due to electric shock when touching live parts.

• Disconnect from mains and secure against reconnection!

• USE ONLY ORIGINAL SPARE PARTS.

• Replace illuminants and fi lters only with ones which are characterized on the device.

• Use only original KBL ballasts (art. no.

3200271131) for intelliSun and CPI-Energy sunbeds.

ACRYLIC PANES, GRAB HANDLES AND DOOR

HANDLES

• If possible, use the special cleaning and disinfectant agent “megaClean” supplied by KBL for cleaning the acrylic parts and handles, and dilute it in water at a ratio of 1:13.

VARNISHED AND PLASTIC PARTS

• Use a damp soapy cloth to clean the varnished and plastic surfaces.

• Do not clean the large plastic parts with a dry cloth.

This might scratch the surfaces!

CHROMIUM-PLATED PARTS/MIRROR

• Only clean with a damp chamois and a cleaning agent for acrylic plastic (antistatic). Apply the cleaning agent onto the chamois and not directly onto the mirror surface.

CLEANING AGENTS

• The surfaces and the acrylic panes must not be cleaned with concentrated disinfectants or solvents or other liquids that contain alcohol!

Instructions for cleaning and care

GENERAL

• Before starting to clean the unit, take off any rings, bracelets, watches, etc. that you might be wearing in order to avoid scratching the surfaces.

• Cleaning fl uid must not run into the appliance.

TUBES

• To preserve the tanning power, we recommend cleaning the tubes and UV lamps with warm water and a chamois after approx. 200 hours of operation.

40


Maintenance intervals

Component/ wearing part

Cleaning/care Replacement

C o n d e n s a t e tank

Air fi lter

If a corresponding message is displayed.

Depending on local conditions after approx. 100 operating hours

When necessary

/

Tubes

- IntelliSun

- CPI

Tubes

- Electronic

Power

After approx.

200 operating hours

After approx.

200 operating hours

Typical value after about 1100 operating hours.

For further information see data sheet.

Typical value after about 800 operating hours.

For further information see data sheet.

After approx. 500

- 600 hours

Facial tanners

When necessary

Collagen booster

Acrylic pane

(bench)

Acrylic panes

(others)

After approx.

200 operating hours

When necessary

When necessary

When necessary

After approx.

1500 hours

When necessary aquaCool nozzles

When necessary

After approx. 1000 hours

Shoulder tanner

Ropes of the canopy drive

Air hoses

Airconditioning unit

When necessary

Check and grease after

500 - 600 hours.

Check after 500

- 600 hours.

Clean the heat exchangers after 500 -

600 hours and check the condensate pump.

After approx.

600 hours

Replace all ropes after 3000 hours.

When necessary

When necessary

Tools and aids

4

Hexagon socket screwdriver (SW 4 / 60 mm) Art. No.: 3410055263

Standard Phillips screwdriver (PH2)

PH2

Phillips screwdriver (PH2) 90° offset

PH2

4

Hexagon socket spanner SW 4

Pipe wrench SW 19

19

10

Open-ended spanner SW 10

13

Open-ended spanner SW 13

↵

Finally acknowledge a process by pressing the Start button (interior display).

Number of required persons

The following chapters describe the work steps required for carrying out maintenance and care actions.

At the beginning of each chapter, the required tools and aids are depicted, unless the corresponding process can be carried out by one individual person without any further auxiliary equipment.

The assembly is basically carried out in reverse order of the disassembly.

Exceptions are especially pointed out.

If you open the bench part or one of the acrylic panes, you must, after closing, acknowledge a warning message appearing on the interior display.


Unlocking the bench

↵

Attention !

The bench must only be opened with bench pane folded down.

①

TILTING DOWN THE CANOPY PANE / SIDE PANE

4

↵

Attention!

Prevent the pane from falling down when opening it!.

• Open the middle pane lock at last

Ⓑ.

A B A A B A

②

Canopy pane

①

Press the bench slightly downwards and keep it pressed.

②

Open the lock.

⇒ Tilt up the bench.

Acrylic panes

TILTING UP THE BENCH PANE

↵

③

④

④

③

④

Hold the bench pane in the middle of the front edge and lift it.

Lock it in place using the lateral support plates.

Open

Close

Side pane

⑤

42


⑤

Open the 3 locking spigots by using the hexagon socket screwdriver supplied

(3410055263).

⇒ Tilt the pane down.

REMOVING THE CANOPY PANE

4

PH2

↵

It is not usually necessary to remove the canopy pane for maintenance and cleaning operations. Should you prefer to work with the canopy pane removed, though, please proceed as follows:

PH2

⑥

⑦

⑥

⑦

⑧ ⑨ ⑧ ⓐ ⓑ

⑧

⑧

Call in a second person and hold the pane at the two ends.

Then slightly lift the pane ⓐ and remove it from the rear holding section ⓑ .

⑨

Carefully pull the pane towards the front and out of the tanning area.

⇒ Deposit the pane in a safe place.

ASSEMBLY NOTE

Proceed in reverse order in order to re-install the canopy pane. Make sure that the pane seal is correctly positioned.

Page

42

Tilt the canopy pane down.

⑥

Remove the strain relief of the display cable

(Phillips screw M4).

⑦

Detach the display cable.

When closing the canopy pane, make sure that the pane seal is correctly positioned.


Filter panes

4

4

↵

SAFETY FUNCTION

The facial tanners are equipped with an additional safety function. There is a protective pane-switch behind each fi lter pane. This switch turns off the tanner if the fi lter pane is missing or broken.

REPLACING THE FILTER PANES

⑬

⑭

REPLACING THE FILTER PANES (PREPARATION)

⑫

⑩

⑪

⑬

⑭

The pane is fi xed with two clamps each on the two longitudinal edges.

Remove the pane from the spring retainer.

To do so, press the pane to be exchanged slightly against a pair of clamps and, while keeping it slightly pressed, tilt it out of the holder on the relieved side.

⑪

⑫

Page

42


Page

42

Tilt the side pane down.

⑩

Undo the screws of the mirror panels (6 x M5).

⑪

Remove the central panels.

⑫

Tilt up the outer panels.

The fi lter pane of the side part is replaced analogously to the procedure described for the canopy ⑬ ⑭.

Difference:

• Use an angled hexagon socket spanner (4 mm) in order to undo the screw of the mirror panel ⑩.

DANGER

Excessive UV radiation

Operating the tanning unit with defective fi lter panes can result in serious injury to skin and eyes.

• Never operate the sunbed if the fi lter pane is not present or defective.

• Carry out regular visual inspections.

• Replace fi lter panes only with ones of the same type.

• Have the fi lter panes installed only by trained technical personnel.

44


Tubes

4

↵

• When installing the tubes, make sure that the tube inscription is visible. If it is installed in a different position, there will be no tanning effect.

• After new tubes have been installed, the operating hours of the tubes must be reset in the service menu.

REMOVING TUBE ⓑ

90 0 ⓐ

TUBE REPLACEMENT CANOPY / SIDE PART

Page

42

Tilt the canopy and / or side pane down.

⇒ Remove the tubes.

P2 Tubes

If your tanning unit is equipped with P2 tubes, maintenance and care intervals are equal to the cycles for standard tubes.

Perfect

Ta n

+

V it a m in

TUBE REPLACEMENT IN THE BENCH PART

Danger of destruction!

When installing / dismantling the P2 tubes, pay attention to the middle holding clamp.

Page

42

Open the bench pane.

⑮

If the sunbed is equipped with an airconditioning unit, remove the ducting pane.

⇒ Remove the tubes.

Facial tanners

4

↵

Refl ector

High-pressure lamp

Lamp holder


REPLACING THE HIGH-PRESSURE LAMP

Attention!

The high-pressure lamps must only be installed and removed by trained technical personnel.

Shoulder tanner

PH2

The “x-tra Tan” shoulder tanner ⑱ can optionally be installed in the place of the right-hand shoulder part.

Dirt accumulation and bad seating can lead to damage during the operation.

• Insert the high-pressure lamps straight into their holders.

• When installed, the little glass pin in the middle of the light bulb must point towards the refl ector.

• Never touch the lamp or the refl ector with your bare hands. If necessary, remove grease and dirt with an alcohol-containing agent.

⑱

⑰

REPLACING THE HIGH-PRESSURE LAMP

Attention!

The high-pressure lamps must only be installed and removed by trained technical personnel.

⑯

Page

42

Tilt the canopy and / or side pane down.

Page

44

Remove the fi lter panes.

⑯

Hold one end of the high-pressure lamp. Use a clean cloth free from grease.

⑰

Press the lamp against one side of the holder.

As soon as the relieved side is loose, take the lamp out of the holder.

Dirt accumulation and bad seating can lead to damage during the operation.

• Make sure that tanners and high-pressure lamps are correctly positioned in their respective holders.

• Make sure that the contact surfaces are clean when you insert the lamp.

• Never touch the lamp with your bare hands.

If necessary, remove grease and dirt with an alcohol-containing agent.

46


⑲

PH2

+

⑲

Undo the retaining screw (M6x12) of the chromium-plated covering.

⇒ Remove the chromium-plated covering.

⑳

⑳ Turn the tanner (approx. 45°) to loosen it from its holder. Then pull it off carefully.

Spring washer

Centring lug

Pull the high-pressure lamp carefully out of its holder. Use a clean and grease-free cloth.

Replace the spring washer.

INSTALLATION NOTE

Installation is made in reverse order. Make sure that the high-pressure lamp is correctly positioned .

Interior unit lighting

The lighting from inside the tanning unit

(fourSeasons) is effected by high-performance

LEDs.There are LED modules located inside the unit, in the canopy and in the side part. The outer decorative lighting also consists of LEDs. In the case of a defect, replacement can only be made by qualifi ed technical personnel. Contact your service partner in this case.

Collagen boosters

In the case of a defect, replacement can only be made by qualifi ed technical personnel. Contact your service partner in this case.


Filter cartridges

The cooling air for canopy and bench is fi ltered.

Your sunbed is equipped with fi lter cartridges and continuous-service fi lter inserts. Therefore, purchase and replacement of conventional fi lter pads are not required. Clean the fi lter inserts after approx.

100 hours of operation, depending on the local circumstances. Vacuum the fi lter inserts or use a dishwasher.

FILTER CARTRIDGES IN THE CANOPY PART

Bench

Canopy

There are four fi lter cartridges each in the canopy and in the bench part.

NOTE

Take the opportunity and check and clean the heat exchangers of the air-conditioning unit (See also the chapter “Maintenance/Ventilation and airconditioning”). Soiled heat exchangers substantially reduce the performance of the air-conditioner.

FILTER CARTRIDGES IN THE BENCH PART

Page

42

Open the bench part.

Open the lock of the fi lter insert.

⇒ Remove the fi lter insert.

Page

42

Fold down the canopy pane.

Open the retaining clamp of the cartridge.

⇒ Remove the fi lter insert.

When installing the insert, make sure that the honeycomb grill is directed towards the inside.

Canopy drive

10/13

4

PH2

Service the wire ropes after each tube replacement in order to guarantee a trouble-free operation of the drive.

19 PH2

↵

SERVICING THE CANOPY DRIVE

⇒

⇒

⇒

Test the canopy drive. The canopy must lock in place in all positions. If it does not, the canopy springs must be tensioned .

Check the ropes of the canopy drive. Should individual wires be frayed, replace the rope immediately.

Grease the rope in the area of the return pulley with copper crease or adhesive lubricant

HHS-2000 (KBL 1200024000).

48


REPLACING THE SPRING-LOADED WIRE ROPES

(PREPARATION)

PH2

Page

42


Disconnect the cable connections of the audio system (only on right-hand side).

Pay attention to the correct connections according to the colours during the subsequent assembly.

⇒ Close the bench.

ⓐ ⓑ

Remove the screw (M6x12) of the shoulder tanner or the shoulder part.

⇒

Disconnect the plug-in connector of the cable harness from the base plate of the shoulder tanner.

Remove the shoulder tanner or the shoulder part.

Remove the foot panel and undo the cable of the decorative lighting .

10

Solve the front locking screw at the bottom spacer and remove the side panel -> pull forward .


Page

42

Tilt down the side pane.

Loosen the hexagon socket head screw

(SW10) by approx. two turns.

Remove the hinge cap.

REPLACING THE SPRING-LOADED WIRE ROPES

13

PH2

Page

42


Remove the front fastening of the end cap of the canopy (Phillips screw).

19

Remove the end cap of the canopy and pay attention to the cable of the decorative lighting .

Disconnect the cable connection of the decorative lighting on the inside of the canopy end cap.

Involve a second person to secure the canopy against falling down.

Remember the position of the nut at the spring tensioner. Then slacken the spring using a pipe wrench SW19.

Undo the upper rope holder SW13.

⇒ Replace the wire rope. Fix and tension it.

Grease the rope in the area of the return pulley with copper crease or adhesive lubricant

HHS-2000.

50


Ventilation and air-conditioning

↵

In order to preserve the performance of the air-conditioning unit, clean the heat exchangers after

500 - 600 hours of operation.

Air-conditioning unit

SERVICING THE VENTILATION SYSTEM

⇒ Check all hose connections.

⇒

Remove any kinks in the air hoses. Replace defective hoses immediately.

The exhaust air hose must not exceed a maximum length of 6 m if there is no auxiliary fan installed.

CHECKING THE CONDENSATE PUMP

The condensate pump pumps away the condensation water at timer-controlled intervals.

Check the function of this pump with each tube replacement.

⇒

Fill some water into the condensate tray .

Use a hose and a funnel to do so.

Heat exchanger

Condensate pump

Condensate tray

Make sure that the water does not spill over.

⇒

⇒

Start a tanning session and then wait for 20 minutes.

The fi lling level of the tray must then be below the pump level.

Page

42


Clean the heat exchanger.

Vacuum it carefully, paying attention not to damage the fi ns.


EMPTYING THE CONDENSATE TANK

The condensate pump transports the condensation water into a canister via a hose. Once this condensate canister is full, a corresponding message is displayed.

The air-conditioning symbol fl ashes (check), and the air-conditioning unit switches off shortly afterwards.

50

⇒

Unscrew the closing lid of the condensate canister.

Empty the condensate canister.

When closing, make sure that the condensate hose is inserted a max. of 50 mm into the canister.

Finally, acknowledge the aircon message on the display (START).

Recording to an SD card

↵

REMOVING THE SD CARD

The SD card slot which contains the storage medium with the MP3 data from the internal MP3 player is located at the control box in the bench part of the sunbed.

Please refer to the chapter “Technical data” for information regarding supported card sizes as well as fi le-system and MP3 formats. The SD card must not be formatted, the Voice folder and its contents must not be changed or deleted. Outside of this folder you can add or delete audio fi les as you desire. These audio tracks are played if the corresponding source has been selected. The number of fi les is limited by the storage capacity of the SD card.

RECORDING TO THE SD CARD

Attention!

• Do not modify or delete the VOICE folder or the data it contains.

⇒

Insert the card into the computer and wait for it to be recognised.

⇒ Copy fi les to SD card, or delete fi les from it.

52


Replacing Aroma and aquaCool media

↵

Attention!

Do not use any agents other than aquaCool and Aroma gel supplied by KBL!

• Risk of infections

• Function of nozzles impaired

REPLACING THE AQUACOOL CANISTER

Due to the system a residual amount remains in the canister.

REPLACING THE AROMA TIN

When the Aroma tin is empty, a corresponding message is displayed.

If the aquaCool canister is empty, corresponding messages are displayed, and aquaCool switches off shortly afterwards.

Page

42


Unlock the retaining bracket.

⇒

Replace the tin.

Reset the Aroma counter in the service menu to 0 (Reset). Then the message on the display will disappear.

Page

42


Unscrew the lid.

Keep the hose end including the lid in a clean plastic bag while replacing the canister.

Replace the canister.

⇒ Start aquaCool initialization (service menu).

Replacing the aquaCool nozzles

After 1,000 hours of operation, the aquaCool nozzles must be replaced in order to ensure that the aquaCool system functions properly. The assembly instructions are included with your spare parts delivery.


System messages

ERROR MESSAGES

01

02

03

04

08

09

10

After the error has been eliminated, all error messages must be acknowledged by pressing START on the interior display .

No.

Status message

Excess temperature bimetal

Maximum tanning time!

Excess temperature exhaust fan, please check

Connection fan speed control faulty

Canopy pane open, please close

Side pane open, please close

Bench / bench pane open, please close

Description

Bimetal switch triggers.

Remedy

Check the air-intake/air-discharge system. Let the sunbed cool down.

Enabling signal from coin-box system comes in longer than the time value approved under “Maximum tanning time”

(voltage remains connected)

Disconnect from the coin-box system.

Bimetal switch in the fan triggers.

Make sure the fan runs freely. Check the air-intake/ air-discharge system. Let the sunbed cool down.

Faulty communication between Mainboard and fan-speed control.

Check / replace the patch cable.

Contact of the canopy pane has triggered.

Close the canopy pane and check the contact.

Contact of the side pane has triggered.

Close the side pane and check the contact. If the fault persists, contact your Customer Service.

Contact of the bench pane has triggered.

Close the bench / bench pane and check the contact.

11

Excess temperature bimetal x-tra Tan

Bimetal switch in the shoulder tanner triggers.

Check the ventilation system of the shoulder tanner. Let the sunbed cool down. If the fault cannot be eliminated in this way, contact your Customer Service.

12

13

14

15

17

18

19

20

21

22

23

24

25

KBL7 Hardware error Input-Controller

Maximum write cycle fl ash memory reached

Error! SD card read error

(CRC fault)

Error! no access to the SD card

Parameter storage not found, please connect and restart

Parameter storage no valid serial number

CAN-BUS: Interior display

V1 is incompatible

CAN-BUS: preSelection display V1 is incompatible

CAN-BUS: audio module full

V1 is incompatible

CAN-BUS: RGB module V1 ist incompatible

Parameter storage write error

Frequency detection: detection failed!

Mainboard defective.

Parameter storage read error Parameter storage read error.

Frequency detection failed.

Contact your Customer Service.

Maximum write cycle fl ash memory reached.


Update via SD card failed (CRC fault).

Update via SD card failed (access error).

Parameter storage not found, please connect and restart.

CAN-BUS operators incompatible.

Parameter storage write error.

SD card check / replace.

SD card check / replace

Check connector parameter storage. If necessary replace parameter storage.

Parameter storage no valid serial number.


Use CAN-BUS operaters V2.



Restart the controller. Contact your Customer Service after the third unsuccessful restart.

54


ERROR MESSAGES

No.

26

After the error has been eliminated, all error messages must be acknowledged by pressing START on the interior display .

Status message

Frequency detection: power supply connection faulty

(connector X6/E6)!

Description

Frequency detection failed. No mains voltage.

Remedy

Check mainboard connector X6/E6.

INFORMATION MESSAGES

No.

Info. message

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

226

227

Fill level aquaCool canister low

Description

The content of the aquaCool canister is suffi cient for another 2.5 hours of operation with a spraying time of 6 seconds each.

Remedy

Replace the empty aquaCool canister with a full one.

Do not replace aquaCool with any other liquid.

Connection aquaCool unit faulty

Connection audio module faulty

Connection inside display faulty aquaCool canister empty

Communication between control and module / display has been interrupted.

Check / replace the patch cable. Acknowledge the message by pressing START. If the fault persists, contact your Customer Service.

Aroma supply low, please renew aircon:condensed-water canister full, please empty

Low battery charge, please renew

Connection preselect display faulty

Connection RGBmodule faulty aquaCool canister empty.

System has run out of scent.

Condensate canister of air-conditioning unit full.

Button cell (CR-2032) of the control board discharged.

Communication interrupted.

between control and “preSelection” display has been

Replace the aquaCool canister with a full one.

See chapter: Refi lling Aroma and aquacool

Replace the Aroma tin.

See chapter: Refi lling Aroma and aquacool

Empty the condensate canister of the air-conditioning unit, acknowledge the message by pressing START.

Replace the button cell (CR-2032).

Check / replace the patch cable. Acknowledge the message by pressing START. If the fault persists, contact your Customer Service.

SD card missing

SD card unreadable

Connection to easy

Care terminal faulty

No SD card in the audio module.

SD card defective, incompatible content.

Communication between control and easyCare terminal has been interrupted.

Voltage varies, blease check Power supply to the mainboard varies

No voice fi les on the SD card, pleas check.

Quicktest Sensortoleranz

OK

Quicktest Sensortolerance error

No voice fi les on the SD card found.

Sensor Quicktest log entry - No display appears - Message will be stored directly in the event log (service menu).

Insert an original SD card.

See chapter: Recording to an SD card/Removing the

SD card

Insert a new original SD card. Acknowledge the message by pressing START. See chapter: Recording to an SD card/Removing the SD card. If the fault persists, contact your Customer Service.

Check cable connections and power supply. Acknowledge the message by pressing START. If the fault persists, contact your Customer Service.

Check power supply to the mainboard.

Rebuild voice folder on the SD card. If necessary replace original SD card.


Technical data

Ambient conditions

Installation site

In dry rooms (booths) with suffi cient airing and ventilation

• Maximum relative air humidity: ≤ 70 %

• Maximum room temperature: ≤ 30 °C

• Minimum height of the room: 2400 mm

Weights and measures

Dimensions in mm

(Height x width x depth)

Bench pane max. load capacity

Weight

1534 x 2380 x 1430 (when closed)

1942 x 2380 x 1430 (when open)

130 kg approx. 620 kg (with air conditioning)

Electrical connection values

Protective class

Mains voltage

Wire cross section

MP3-Player

Fuses

IP20

400V / ~3N / 50Hz

5 x 4mm 2 Ölfl ex

• Supports SD cards up to 1-2 GB (SD) / 4-16 GB (SDHC)

• Supported fi le system (SD card): FAT16, FAT32

• Supported MP3 fi les: constant and variable bit rate, 96-320 Kbit/s

• Supported MP3 fi les (USB-Port): constant and variable bit rate, 96-320 Kbit/s

Automatic fuse K-type (safety cut-out), 3-pole, (3x20A -> 6700 Super) (3x25A -> 6700;

6800; 6900 SP & UP & IS) with residual current operated circuit breaker (RCD)

Air discharge

Fan

Exhaust-air hose

Views

Exhaust-air socket Ø 300 -- 2095 mm (top) - Minimum exhaust air fl ow rate: 2250m 3 /h

Ø 300

56


UNIT DATA - UV type 3 and 0.3 W/m 2 in compliance with EN 60335-2-27

megaSun 6700 alpha - business

Super Item no Equivalency code range

Tubes

Canopy: 18x ultimate 1806 R 100W

Side: 6x ultimate 1806 R 100W

Bench: 20x ultimate 1919 R 120W

3230076000

3230076000

3230076110

100-R-(20-27) / (2,6-3,6)

100-R-(20-27) / (2,6-3,6)

120-R-(19-25) / (2,1-2,9)

Facial tanner

Shoulder tanner

Collagen booster

4x MS600

2x MS250

-

3230303000

3200224000

Filter panes

EVO 19176

Nominal power

Tubes

Electronic Power: With air conditioning: 8960W

Without air conditioning: 7700W

Super Power




Facial tanner

Shoulder tanner

Collagen booster

4x MS600

2x MS250

-

Filter panes

EVO 19176

3020019176

CPI: With air conditioning: 11260W


Item no

3230076114

Equivalency code range

160-R-(21-28) / (2,2-3)

3230076114

3230076110

3230303000

3200224000

3020019176

160-R-(21-28) / (2,2-3)

120-R-(19-25) / (2,1-2,9)

Nominal power

Tubes



Ultra Power




Facial tanner

Shoulder tanner

Collagen booster

4x MS600

2x MS250

-

Filter panes

EVO 19176

Nominal power





Item no

3230076114

Equivalency code range

160-R-(21-28) / (2,2-3)

3230076114

3230076115

3230303000

3200224000

3020019176

160-R-(21-28) / (2,2-3)

180-R-(24-32) / (2,1-2,9)





megaSun 6800 alpha - hurricane

Ultra Power Item no Equivalency code range

Canopy: 20x hurricane 1809 R 160W 3230076128 160-N-(23-30) / (2,7-3,7)

Tubes

Side: 6x hurricane 1809 R 160W

Bench: 20x hurricane 1923 R 180W

3230076128

3230076129

160-N-(23-30) / (2,7-3,7)

180-N-(23-30) / (3,0-4,0)

Face tanner

Shoulder tanner

Collagen booster

4x MS600

2x MS250

-

3230303000

3200224000

Filter panes

EVO 19176

Nominal power



3020019176




megaSun 6900 alpha - deluxe

Ultra Power - intelliSun Item no Equivalency code range

Tubes


4x ultimate 1863 O 80W


2x ultimate 1863 O 80W


3230076114

3230074882

3230076114

3230074882

3230076115

160-R-(21-28)/(2,2-3)

80-O-(15-20)/(7,4-10)

160-R-(21-28)/(2,2-3)

80-O-(15-20)/(7,4-10)

180-R-(24-32)/(2,1-2,9)

Face tanner

Shoulder tanner

Collagen booster

4x MS600

2x MS250

40x facial collagen booster

3230303000

3200224000

Filter panes

EVO 19176

Nominal power

CPI: With air conditioning: 11360W - 13360W

Without air conditioning: 10100W - 12100W

3020019176

58


EQUIVALENCE KEY FOR UV FLUORESCENT LAMPS

Marking of UV fl uorescent lamps according to IEC 61228

Sample coding of a lamp

160-R-32 / 3,2

Use of replacement tubes.

The tanning tables referring to this sunbed are only valid as long as the system is operated with the original tube set!

Ratio of the NMSC-effective

UV irradiance ≤ 320nm und > 320nm

(NMSC = Non Melanom Skin Cancer)

Erythema-effective UV irradiance in the range of

250-400nm in mW/m 2

Refl ector types

O - For lamps without refl ector

B - For lamps with refl ector angles wider than >230 0

N - For lamps with refl ector angles narrower than <200 0

R - For lamps with usual refl ector angles of ≥200 0 ∧ ≤230 0

Indication of Watts (electrical power)


Ringstraße 24-26

56307 Dernbach / Germany fon: +49 (0) 26 89.94 26-0 fax: +49 (0) 26 89.94 26-66 mail: [email protected]

www.megaSun.de

No results