advertisement
General safety advice
• Follow all instructions given in this manual. In addition, observe all relevant statutory provisions and regulations, also those applicable in the country of operation.
• The unit must only be installed and assembled by specifi cally trained staff.
• Arbitrary modifi cations or conversions of the equipment are not permissible.
• Observe all danger signs and safety notices attached to the equipment.
• Safety notices must not be removed, and safety equipment must not be disabled or removed.
• The unit must only be operated when in perfect working condition.
• Never operate the unit with the outer covers or acrylic panes removed.
• The tanning system must be controlled via a timer that complies with the generally applicable standards.
• Absolutely observe the maintenance frequencies indicated in the maintenance plan.
• Pay attention to the load limit of the bench pane
(tanning bed units only).
• The bench must only be opened with bench pane folded down.
Updating the system software
ATTENTION
Risk of damage by switching off the power supply voltage.
Disconnecting power supply during the update process, will lead to damage of electronic components.
• Make sure that the unit is not disconnected from the power supply voltage during the update.
To accomplish the update download the “USB-
Connect” software offered by KBL. For detailed information press the help-button in the main menu.
Tanning times
Adhering to tanning times and schedules is essential.
6
O p e r a t i n g I n s t r u c t i o n s | megaSun 6700 - 6800 - 6900
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 General information
- 4 About these instructions
- 4 Transport by forklift truck
- 4 Other modes of transport
- 4 Old equipment disposal
- 4 Service
- 5 Safety notes
- 5 Intended use
- 5 Duties of the operator
- 5 Timer operation
- 6 General safety advice
- 6 Tanning times
- 6 Updating the system software
- 7 Description of the unit
- 7 Standards
- 7 Components
- 8 Connections
- 8 Connecting the mains voltage
- 8 Connecting an external audio source
- 8 Level adjustment studio music signal
- 9 Operation using different audio sources
- 10 Bluetooth connection
- 11 Connecting the channel selection
- 12 Connecting the external timer
- 12 aquaCool and Aroma connections
- 13 Start-up
- 13 Operating modes
- 14 Tanning instructions
- 14 Instructions for the user
- 15 Tanning times
- 16 Tanning mode
- 16 preSelection
- 18 Starting the tanning session
- 18 Operation during the tanning session
- 19 Basic functions
- 20 Variable section of the control panel
- 22 Standby mode / service mode
- 22 Layout of the display numbers
- 22 Switching the decorative lighting on and off
- 22 Collagen boosters in standby mode
- 22 aquaCool spraying test
- 22 Invoking the service menu
- 23 Service menu - Basics
- 25 Service menu - Overview
- 26 PIN protection
- 26 Service menu - options
- 39 Set decorative lighting
- 40 Maintenance and cleaning
- 40 Instructions for cleaning and care
- 41 Maintenance intervals
- 41 Tools and aids
- 42 Unlocking the bench
- 42 Acrylic panes
- 44 Filter panes
- 45 Tubes
- 45 P2 Tubes
- 45 Facial tanners
- 46 Shoulder tanner
- 47 Interior unit lighting
- 47 Collagen boosters
- 48 Filter cartridges
- 48 Canopy drive
- 51 Ventilation and air-conditioning
- 52 Recording to an SD card
- 53 Replacing Aroma and aquaCool media
- 53 Replacing the aquaCool nozzles
- 54 System messages
- 56 Technical data
- 56 Views
- 58 in compliance with EN
- 58 Electronic Power: With air conditioning