www.altronics.com.au
®
A 1700 24 Hour
Programmable Timer
O
PERATING
I
NSTRUCTIONS
This simple to operate digital timer allows numerous variations of ON/OFF cycles every 24 hours. It can be configured to 14 on cycles every day. Additionally , it may be programmed to operate on any combination of days ( ie. weekdays or weekends). The on duration is variable and can be set from 1 second to 23 hours 59 minutes and 59 seconds. It is ideal for programming period breaks in schools or change of shift bells in factories and work places. The in-built digital clock can be set to one of three modes of operation, manual , automatic and off. In the manual mode you may override any programmed setting , the automatic mode switches on at the pre-programmed times and the off mode disables the pre programmed on times.
F
EATURES
• 19” 2U Rack mount or desk mount
• Timer may trigger Chime or 24VDC out
• Choice of 240VAC or 24VDC operation
• Choice of 5 tones for the bell chime
• In-built manually operated Alert/ Evac switches
• Remote trigger contacts for Alert,Evac and Chime
• Programs are retained during power failure
• Up to 14 “ON” programs per 24 hours
• Unit may be programmed to operate on any combination of days
• 2 Year warranty
• Made in Australia
O
PERATING
I
NSTRUCTIONS
To install and operate the unit you will need to programme the timer as follows.
1) Set the current time and day . clear the entire memory. Hold down the CLOCK key and press either the DAY, HOUR, MIN or SEC key continuously until the desired day or time is shown.
Then lift your finger off the CLOCK key to start the timer operating.
2) Set the ”ON” duration for all programs
Press TIMER key, the display will show :
ON
TIME
ADJ
Set the duration of all the programs (T1) by pressing
HOUR, MIN and SEC keys until the desired “ON” duration is displayed. It is recommended that you use durations of no more than 1 second for a single chime tone. For longer chime durations you will need to set dip switch 3 to ON as well as programming the ON duration for a longer period.
To review the programmed duration , press the timer button when in timer function.
3) Set the programmed “ON” times.
After setting the ON duration, press the TIMER button again to bring up the first “ON” program.
Use HOUR , MIN and SEC buttons to set the first program start time. Use the DAY button to set the desired day or sequence of days this program will operate on.
You may then press TIMER again to set the “ON” time for programs 2 - 14.
Distributed by Altronic Distributors Pty. Ltd. Perth. Western Australia.
Proudly Assembled in Australia
Doc. PS1215
Page 1
REDBACK A 1700 Programmable Timer
To exit programming press the CLOCK button , this will return you to the timer function.
To review a programmed “ON” time press the TIMER button until the program you wish to alter is displayed.
4) Switch the unit to “Auto” mode.
For the programmed “ON” times to operate the unit must be switched to Auto mode. Use the button marked
MANUAL until the dash indicator is above the word
AUTO. In this mode the programs will function at the prescribed times and days.
5) Use of Manual or Off
Manual operation allows the user to override a program.
To use the timer in manual mode press the MANUAL key until the dash indicator is over the word On.
This will turn the timer on. The timer will stay triggered until you manually set the timer to the “OFF” position.
To set the timer to the off position press the MANUAL key until the dash indicator is over the word Off.
OFF.
R
EAR
W
IRING
C
ONNECTIONS
The connections on the rear of the unit require some explanation in order to set up for continuous trouble free use.
The 10 way pluggable terminal is labelled Evac, Alert,
Chime, 24V Out and Timer 24V Out.
The terminals activate the assigned tone, e.g. if you want the ALERT to sound from a remote location the contacts may be connected to a normally open switch which when pressed will trigger the ALERT tone and will then sound as if the ALERT button on the front panel was pushed, and the same applies to the EVAC and CHIME terminals.
The 24VDC switched out terminal has no output until a button or the timer activates a tone. When a tone is activated 24VDC is present across the positive and negative terminals .
T
ABLE
1 : D
IP SWITCH SETTINGS
Switch Number 1 2 3 4
Chime Tone: Single Bing
Bing Bong
Single Bong
Siren
OFF OFF OFF –
OFF OFF ON –
ON OFF OFF –
ON ON OFF –
Deedle Tone OFF ON OFF –
*Repeating Bong ON OFF ON –
*Repeating Siren ON ON ON –
*Repeating Deedle OFF ON ON –
* These tones will sound continuously for the duration of the timer or as long as the chime button is pressed.
Chime Tone Switch Settings
To set the tone for “ON” cycle , use the dip switch setting table to obtain the type of tone you wish to output.
The factory setting for the chime tone will be single Bing.
Dip switch 4 makes the alert/evac tone cycle continuously after it is triggered or stay on only while the
Alert/evac button is held down.
To enable the alert /evac to operate continuously switch dip switch 4 to ON. Note that this will be factory set to
1 2 3 4 5 6 7
There is a switch next to the Timer 24V Out terminal on the rear of the unit. This allows you to select whether the timer “ON” cycle triggers the Timer 24V out contacts or the chime. If this switch is in the “Up” position , the timer will cause 24VDC to appear across the “Timer 24V out “ contacts. In the “Down” position , the timer will trigger the chime.
Note : this switch will be factory set to “Down”.
8
Rear view
The RCA Sockets are line level (1V) outputs, which are run to an amplifier or mixer input.
Power Supply
The power for the unit may come from either 24VDC or
240 AC , for 240V operation simply plug the 240V power cord into the socket labelled 240VAC.
For 24VDC operation , use the terminal marked 24VDC.
Caution: The 24VDC is polarised and may cause dam- age to the unit if not connected correctly. The polarity is marked on the unit, just under the terminal.
Power only needs to be in one form either AC or DC to work. Both 24VDC and 240VAC can be connected at the same time (for battery backup).
Volume Controls
9 10 11 12 13 14
Key
1. 240V AC power in
2. 24VDC power input
3. DC Fuse (3A)
4. Chime Level
5. Voice-over Level
6. Alert/Evac Level
7. Dip Switches
8. Line Output (RCA)
9. Evac remote contacts
10. Alert remote contacts
11. Chime remote contacts
12. 24VDC output
13. Timer switched 24VDC
14. Chime/24VDC switch
Page 2
Doc. PS1215
REDBACK A 1700 Programmable Timer
The volume controls can be found on the rear of the unit, these should be adjusted with a small phillips head screwdriver or adjustment tool.
Chime Volume controls the output level of the Chime.
Voice Over controls the level of the optional Voice Over module (A 2072) if installed.
Alert/Evac Volume controls the level of the Alert and Evac tones.
Adjust the output volumes to the desired levels.
Pin 1
Mic
Relays
Use ribbon cable & connectors provided to join terminals (Pin
1 is the black pin)
IC
T
HE
O
PTIONAL
V
OICE OVER
M
ODULE
The A 1700 timer panel has the option to fit the A 2072 voice over module. This will add a voice message to the evacuation cycles when the evacuation cycle is triggered.
Use with the A 1700 Timer and tone generator
Connection to the A 1700 is via the 5 way keyed header cable (JP1). The Voice-over Module will play a recorded message twice in succession after every four evacuation cycles. The volume control on the A 1700 Timer , labelled
“Voice over level” is used to vary the volume ratio between the evacuation tones and the voice playback.
5 Pin Header (JP1) Pinouts
Pin Function Description
1
2
3
4
Vcc
GND
AUDIO
PLAY
Regulated +5V input*
Ground 0V
Audio output, line level 10k
Ω
A momentary high to activate
5 the message playback
PLAYING This line goes low to indicate a message is currently being played
B
ATTERY
R
EPLACEMENT
Periodically the CR2302 lithium battery located within the time clock (Altronics part No. S 4999) should be replaced, this should not be necessary to be done more often than once in 4- 5 years , or should the timer begin to loose programs or time. To replace the lithium battery in the unit, disconnect power to the unit. Open the lid and peel off the label on the rear of the timer. You will then see a screw type battery cover. Un-screw this cover and remove the old battery. Checking that the orientation is correct place the new battery in the timer and screw down the cover. The panel should now have a reading on the display.
You will need to re-programme the settings on the timer
(refer to that part of the operating section for instructions on re-programming the settings on the timer ).
Diagram to connect up the A 2072 Voice over module to the timer.
Refer to the text and the instructions for the A 2072 to assist in the connection
T
Pin 1
ROUBLESHOOTING
U
NIT DOES NOT SWITCH ON AT THE
REQUIRED HOUR
Check programs for the correct switch on times.
Check timer for the correct time.
U
NIT DOES NOT SWITCH OFF AFTER
THE ELAPSED TIME
Check timer for the correct “ON” time.
N
O
P
OWER TO
U
NIT
Check DC fuse.
Check power switch is on and confirm unit is plugged in to either 24VDC or 240VAC.
T
IMER FAILS TO TRIGGER
T
ONE
/ 24V
OUT
Check that the timer 24VDC out switch is set correctly.
Check line out connections to amplifier/ preamp.
Check connections to timer 24VDC out terminals.
T
IMER FAILS TO DISPLAY OR KEEP
CORRECT TIME
Replace battery in timer.
A
LERT
/
EVAC CONTINUE TO OPERATE
AFTER THE SWITCH IS RELEASED
Check dip switch settings.
I
NCORRECT TYPE OF TONE SOUNDING
WHEN CHIME IS PUSHED
Check Dip switch settings
E
VAC
, C
HIME OR VOICE OVER LEVEL
TOO LOW
Adjust volume controls.
Doc. PS1215
Page 3
REDBACK A 1700 Programmable Timer
A Circuit Diagram of the A 1700 Timer/ Tone generator.
Page 4
Not field serviceable: For repair contact
Altronics for your nearest Service Centre :
Altronic Distributors Pty. Ltd. Perth W.A. 6000
Phone: (08) 9428 2199 Fax: (08) 9428 2198
S
PECIFICATIONS
OUTPUT LEVEL: .....................................1V (Line level)
DISTORTION: .......................................................0.01%
Tone Selection /
Alert Evac operation...........................Dip Switches
FREQ. RESP.: .........................................140Hz - 20kHz
SIGNAL TO NOISE RATIO:
Alert/Evac/Chime: ............................-70dB typically
OUTPUT CONNECTORS:
Audio Output: ...........................RCA Stereo Socket
Switched 24V DC Out:............Pluggable Terminals
Timer activated 24V DC Out: .Pluggable Terminals
INPUT CONNECTORS:
24V DC Power: ........................Pluggable Terminals
240V AC Power:.........................IEC Chassis Socket
Remote Alert, Evac, Chime:......Pluggable Terminals
CONTROLS:
Day, Hour , Minute, Second
Clock, Manual/ Auto/ Off set............Timer controls
Alert, Evac, Chime, Voice over: ........Rear Volume
Power: ................................................On/Off Switch
Alert Switch: ......................Illuminated Push Switch
Evac Switch: ......................Illuminated Push Switch
Bell / Chime Switch:..........Illuminated Push Switch
Cancel Switch:...............................Push Switch
INDICATORS: ..........................................Power on LED
POWER SUPPLY: ..........................240V AC or 24V DC
DIMENSIONS:..............................
≈ 482W x 152D x 44H
WEIGHT: ...........................................................
≈ 2.3 kg
COLOUR: ...............................................................Black
OPTIONS: ............................A 2072 Voice Over Module
* Specifications subject to change without notice.
Distributed by Altronic Distributors Pty. Ltd. Perth. Western Australia.
Phone: 1300 780 999 Fax: 1300 790 999
Internet: www.altronics.com.au
Doc. PS1215
