Mitsubishi Electric MR-G50M T-C, W-C Home Refrigerator Service Manual
The MR-G50M T-C and MR-G50M W-C home refrigerators feature space-efficient storage, a vegetable compartment that extends the shelf life of vegetables and an auto ice maker. The refrigerators are also equipped with a defrost system, a temperature control system and a room light.
Advertisement
Advertisement
HOME REFRIGERATOR
SERVICE MANUAL
Model
MR-G50M-T-C
MR-G50M-W-C
No. OAH094
Model name indication
(Inside this door)
C •••• Taiwan
CONTENTS
1. FEATURES ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••2
2. SPECIFICATIONS ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••3
3. WIRING DIAGRAM ••••••••••••••••••••••••••••••••••••••••••••••••••••••••5
4. OUTLINES AND DIMENSIONS •••••••••••••••••••••••••••••••••••••••••7
5. REFRIGERANT CIRCUIT ••••••••••••••••••••••••••••••••••••••••••••••••8
6. TROUBLESHOOTING•••••••••••••••••••••••••••••••••••••••••••••••••••••9
6-1 FUNCTION OF OPERATION PANEL •••••••••••••••••••••••••••••9
6-2 FLOWCHART OF SELF-CHECK •••••••••••••••••••••••••••••••• 14
6-3 BLOCK DIAGRAM OF PRINTED CIRCUIT BOARD •••••••• 17
6-4 AUTO ICE MAKER ••••••••••••••••••••••••••••••••••••••••••••••••• 17
6-5 FLOWCHART OF TROUBLE CRITERION •••••••••••••••••••• 19
6-6 TROUBLE CRITERION OF MAIN PARTS ••••••••••••••••••••• 26
6-7 TEST POINT DIAGRAM OF FILTER BOARD •••••••••••••••• 31
6-8 TEST POINT DIAGRAM OF CONTROL BOARD •••••••••••• 32
7. NAMES OF THE PARTS ••••••••••••••••••••••••••••••••••••••••••••••• 33
8. DISASSEMBLY INSTRUCTIONS ••••••••••••••••••••••••••••••••••••• 34
PARTS CATAROG (OAB094)
NOTE:
• RoHS compliant products have <G> mark on the spec name plate.
1
FEATURES
MR-G50M-C
1. AUTO-shelf
The shelves can be adjusted freely, even with food items placed on them.
Before...
There was unused space when big items were stored. (Conventional models)
From now on...
Space-efficient storing allows two dozen 350 ml cans to be stored additionally. *1
*1
Refrigeration compartment with large 239 L capacity.
*1 Comparison of 2006 MITSUBISHI refrigerator MR-G40J and 2007 new model MR-G45M.
2. Vegetable compartment
"Reducing sugar" extends shelf life of vegetables.
Tricolor LEDs
Blue
Increases vitality of vegetables together with the orange LED.
About 3 times more water retention *2
90% high humidity storage
*3
Direct air to vegetables is avoided.
The vegetable case is cooled from the surface of three walls, and pleasant humidity is maintained by the humidity sensor mounted just for the vegetable compartment.
Comparison of weight changes (Spinach stored for 2.5 days)
Orange
Forms reducing sugars, which become the source of vital energy of vegetables.
UV
Stimulates vegetables and increases polyphenol.
Radiant cooling
Humidity sensor
2001 model MR-S45A
*2 Number of days it took for the weight of spinach to decrease by 10 percent. Compared between 2001 model MR-S45A, about 2.5 days, and 2007 new model MR-G45M, about 7.5 days. (With vegetables fully loaded)
*3 Moisture evaporated from vegetables are retained in the compartment, maintaining high humidity. Plastic wraps may be needed according to the amount of vegetables, vegetable condition, length of storage, or in case the item to be stored emits strong smell.
Vitamin C increased by approximately 15% *5
Irradiation of LED lights activates vital activity of vegetables, and increases
Vitamin C
Polyphenol increased by approximately 10% *5
The UV-LED stimulates vegetables and increases polyphenol.
Rate of change in amount of vitamin C
(Broccoli sprout
stored for three
days)
Rate of change in amount of polyphenol
(Cress stored for
three days)
*4 Vegetable compartments, which stimulate synthesis of vitamins in leaf vegetables. As of Aug. 24, 2004.
(Research by MITSUBISHI)
*5 Vegetable was wrapped and stored under the LED light. Condition: temperature 5 , humidity 90%. Effect may change
due to factors such as position of vegetables, so the other vegetables block the light, or stored amount.
2
2
SPECIFICATIONS
SPECIFICATIONS
MR-G50M-C
Power supply
Total capacity
Dimensions (H x W x D)
Cabinet
Food liner
Insulation
L mm
V,Hz
Cabinet
Freezer door
Refrigerator door
Cooling system
Freezer
Refrigerator
Evaporator
Condenser
Defrost system
Drain
Temperature control system
Refrigerator compartment room light
Accessories
Weight
Unit
Shipping
Capillary tube
Desiccant (molecular sieve)
Refrigerant filling capacity R600a
Refrigerating oil (Model) kg kg mm g g g
110V,60Hz
495 (R:263 F:90 V:95 I:16 S:31)
1811 x 685 x 709
Acrylic resin coated steel
ABS resin
Foamed polyurethane (Cyclopentane)
Foamed polyurethane (Cyclopentane)
Foamed polyurethane (Cyclopentane)
Forced air convection
Forced air convection
Fin and tube type
Cabinet, cabinet ceiling, sides, back and front flange
Automatic heater defrost
Automatic drainage, Forced evaporation method
Automatic control
110V,10W (E12)
Free pocket (L)
Free pocket (S)
Bottle pocket (S)
Bottle pocket (L)
Tube stand
AUTO-shelf
Two-way flexishelf
Small item case
Free egg shelf
Slide chilled case
Slide chilled case lid
Versa case
Aluminum tray (Versa case)
Water tank (With light-type bacteria removing filter)
Freezing case (upper)
Freezing case (lower)
Ice server
Two-layer soundproof mat
Ice storage bin
Vegetable case
Vegetable stand
Sliding case (Vegetable case)
Drain pan
Toe grille
97
104
1.8 x 0.82 x 2700
9
72
187 (FREOL S10)
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
2pcs.
2pcs.
1pc.
1pc.
1pc.
1pc.
2pcs.
2pcs.
1pc.
1pc.
1pc.
2pcs.
3
ELECTRICAL PARTS SPECIFICATIONS
MR-G50M-C
Model
Power supply
Compressor
Motor protector
Two-way valve
Defrosting timer
Rated input
Starting current
W
A
Running current
A
Winding resistance (A.T.20 )
Model
Ambient temperature
Time
Current
Model
Type
Model
Specification
Sec.
A
Defrost finish
Freezer compartment
Thermal fuse
Defrost heater
Deodorizing function of defrost heater
Heater
Model
Type
Refrigerator
Input
Revolution
Number of poles
Machine
Chamber
(Rating)
W rpm
Model
Type
Input
Revolution
Number of poles
W rpm
Water pipe heater
Rotational heater board
Divider heater (I/S)
Vegetable compartment heater 1
Vegetable compartment heater 2
Ice making tray heater
Tank heater
Duct heater
Ice maker temperature
Model
Dial position
HI
MID
LOW
REFRIGERATOR
CHILLED
LOW (Soft freezing)
MID (Soft freezing)
HI (Soft freezing)
FREEZER
ICE MAKING
ICE MAKING STOP
CRYSTAL ICE MAKING
EFI100E 13DAH
110V,60Hz
45/159 (1620/4800rpm)
2.0 (Current limiter)
0.63/2.19 (1620/4800rpm)
9.27
MM3-71CCV
25
16 or less
17.0
NSCE000DA1
4-phase stepping motor drive voltage DC12V
Control board
Microcomputer
Thermistor 14 1.5
70 2
80.7 (110V,150W)
Not equipped
UDQM002B3
DC brushless motor
2.4 (12V DC)
1520 (12V DC)
10P
UDQM004B3
DC brushless motor
1 (12V DC)
1200 (12V DC)
10P
110V-5.7W
110V-8.0W
110V-3.1W
110V-6.0W
110V-3.1W
110V-10.0W
110V-3.1W
110V-3.1W
-11.6
–
–
–
–
Freezer
Compressor
ON
-20.3
-17.6
OFF
-24.1
-21.4
-14.9
–
–
–
–
–
-18.7
–
–
–
–
–
–
–
–
–
Refrigerator
–
–
–
–
–
–
–
OPEN
-0.6
1.6
4.8
–
–
–
–
–
–
–
–
–
SHUT
-1.8
0.4
3.5
–
–
–
4.4
1.8
-2.3
-4.0
-5.9
OPEN
–
–
NTC thermistor
Versa Slide chilled Ice making
Motor damper
SHUT
–
–
OPEN
–
–
SHUT
–
–
OPEN
–
–
SHUT
–
–
–
2.4
-0.1
-4.0
-5.9
-7.7
–
–
-1.0
–
–
–
–
–
-2.3
–
–
–
–
1.2
–
–
–
–
–
-0.1
–
–
–
–
-17.1
–
–
–
-20.4
–
–
–
–
–
–
–
–
–
–
–
–
-20.2
-20.2
-20.2
–
-23.1
-23.1
-23.1
–
–
–
–
–
–
–
4.2
–
–
Vegetable
Heater
ON
2.3
3.2
OFF
3.5
4.5
–
–
–
5.4
–
–
–
–
–
–
4
3
WIRING DIAGRAM
MR-G50M-C
( SKELETON WIRING DIAGRAM )
OPERATION P.C. BOARD
(LIQUID CRYSTAL DISPLAY)
MOTOR DAMPER MOTOR DAMPER MOTOR DAMPER
TWO-WAY VALVE
(LEV)
ICE GEAR BOX
INVERTER
CONTROL BOARD, N/F BOARD
F1 :10A FUSE
FUSE1 : 3A FUSE
ON THE BOARD
V
U
W
GRAY
WHEN THE DOORS ARE CLOSED.
I.THERMISTOR (Ice making compartment thermistor)
V.THERMISTOR (Vegetable compartment thermistor)
VERSA.THERMISTOR (Versa compartment thermistor)
DEF.THERMISTOR (Defrost thermistor)
ICE-TRAY THERMISTOR (Ice making tray thermistor)
F.THERMISTOR (Freezer compartment thermistor)
C.THERMISTOR (Slide chilled compartment thermistor)
R.THERMISTOR (Refrigerator compartment thermistor)
5
MR-G50M-C
( ACTUAL WIRING DIAGRAM )
BOARD OPERA
1
2
3
4
5
Gray
Red
Black
Sky blue
Violet
1 2
Electric box
RESISTOR
ASSY
CONTROL BOARD
1 2 3 4
12 11 9 8
CN9D
7 6 5 4 3 2 1
16 15 14 13 1211 10 9 8 7
CN4D
6 5
4
3
2 1
8 7
CN8K
6 5 4
2
1 14 1110 9
CN7S
8 7 6 5 4 3 2 1
SSR7 SSR5
SSR4SSR3 SSR2
11
CN3A
7 5 3 1
FUSE1
INVERTER
X1
SSR1
7
CN2A
5 3 1
CN50G
5
3 1
1 2 3 4 5 2 1
N/F BOARD
CN12
3 1
F1
3
CN1
1
Refrigerator
Compartment
REFRIGERATOR
COMPARTMENT
ROOM LIGHT
Yellow
White
White
Orange
White
White
R.
THERMISTOR
1
2
3
4
5
6
Brown
Sky blue
Orange
Gray
Yellow green
Sky blue
Slide
Compartment
C.THERMISTOR
Light brown
Red
Sky blue
Blue
Light green
Sky blue
White
White
3
4
5
6
1
2
7
8
White
Red
Sky blue
Blue
Light green
Sky blue
Light brown
Sky blue
Power
Plug
AC110V
60Hz
1 2 3 4 5 6 7 8
1 2 3
1 2 3 4 5 6
8 7 6 5 4 3 2 1
1 2 3 4 5 6
TANK
HEATER
WATER PUMP
LED
WATER PIPE HEATER
1 2 3 4 5 6 1 2
ICE-GEAR BOX
Ice compartment
ICE-TRAY
THERMISTOR
1 2 3 4
ICE-TRAY
HEATER
Blue
4
Red
3
2
1
White
Yellow
MOTOR DAMPER
Versa
Compartment
1 2 3 4 5 6
1 2
ROTATIONAL
HEATER
BOARD 1
4
3
2
1
Blue
Red
White
Yellow
MOTOR DAMPER
S.THERMISTOR
1 2 3 4
Vegetable
Compartment
1
2
Red
Sky blue
DOOR SWITCH (FOR F-COMPARTMENT)
Freezer
Compartment
DUCT HEATER
THERMAL FUSE (73 )
4 3 2 1
FAN MOTOR
4
3
2
1
Blue
Red
White
Yellow
MOTOR DAMPER
1 2 3 4 5 6 7 8
White
Violet
White
Violet
Violet Violet
Yellow green
Yellow green
VEGETABLE
COMPARTMENT LED BOARD 1
VAGETABLE
COMPARTMENT
HEATER 1
1
2
3
4
3
4
1
2
White
Violet
Violet
Yellow green
F.THERMISTOR
1 2 3 4 5 6
Sky blue
1
2
Pink
DEF.
THERMISTOR
White
White
V.THERMISTOR
VAGETABLE
COMPARTMENT
HEATER 2
Blue
Blue
1
2
Gray
Light green
DEFROST
HEATER
White
1
White
Red
I.THERMISTOR (Ice making compartment thermistor)
V.THERMISTOR (Vegetable compartment thermistor)
S.THERMISTOR (Versa compartment thermistor)
DEF.THERMISTOR (Defrost thermistor)
ICE-TRAY THERMISTOR (Ice making tray thermistor)
F.THERMISTOR (Freezer compartment thermistor)
C.THERMISTOR (Slide chilled compartment thermistor)
R.THERMISTOR (Refrigerator compartment thermistor)
( When the doors are closed. )
6
4 3 2 1
1 2 3 4
MACHINE
CHAMBER
FAN MOTOR
1 2 3 4 5 6
1 2 3 4 5
TWO-WAY
VALVE
3
2 1
MACHINE
CHAMBER
COMPARTMENT
MOTOR
PROTECTOR
COMPRESSOR
(VIEW FROM REAR
LEFT SIDE)
4
OUTLINES AND DIMENSIONS
MR-G50M-C
685 (Display)
283.5
680 (Cabinet)
6
394.5
312.5
310
312.5
318
249
249
400
244
358
337
440
283.5
6
394.5
351
397
396
578(Pitch between the rear wheels)
631(Pitch between the adjust bolts)
666
(Pitch between the front wheels)
72 10
709 (Display)
617 10
Unit : mm
225
580
639 37
203
203
595
581
595
595
314
307
196
547
541
541
539
195
2500
REQUIRED SPACE FOR INSTALLATION
20
685 20
DOOR DIMENSION
L(R) R(R) I S V F
Hight 812 812 214 214 361 361
Width 283.5
349.5
283.5
394.5
684 684
7
211
289.5
654
R(L) : Refrigerator compartment (Left)
R(R) : Refrigerator compartment (Right)
I : Ice making compartment
S : Select compartment [Versa compartment]
V : Vegetable compartment
F : Freezer compartment
5
REFRIGERANT CIRCUIT
MR-G50M-C
Evaporator
Muffler
Suction pipe
Capillary tube
1.8× 0.82×2700(mm)
Dryer
#150
Cabinet pipe
Compressor
Drain pan
Condenser
Charge pipe
(Low pressure side)
6.35
Charge pipe
(High pressure side)
4.0
Two-way valve
8
6
TROUBLESHOOTING
6-1 FUNCTION OF OPERATION PANEL
MR-G50M-C
(1) Function of normal operation
MODE switch
lThe switch functions to
select the required
compartment.
SELECTION switch
lThe switch functions to set the
operation mode or temperature
of compartments individually.
When setting the operation mode of refrigerator, vegetable, and freezer compartment to "Middle" at the same time.
QUICK MODE switch
lEach compartment can
be cooled rapidly.
Quick mode is finished automatically.
It automatically finishes about 2 hours later.
ECO MODE switch
lEach compartment
can be operated with
energy saved.
Press switch and display the
required compartment to apply the
function of temperature adjustment
or quick mode.
Press switch for about 3 seconds until a "beep" sound is heard.
When stopping quick mode halfway
Convenient function
Cooking timer
1
Press switch and switch for 1 second at the same time. ( is displayed.)
(Cooking timer can be released in the same way.)
Cooking timer mode is set and "0" blinks.
Set the time with switch.
? Press to start ? Alarm sound will annonce the
completion of cooking period.
(1~99 minutes) (To stop the timer halfway through the operation, press
Press switch again.
When stopping quick mode of all compartments at once
Press switch for about
3 seconds against one of the compartments which is in
QUICK MODE.
again).
Child lock
2
Press switch and switch for 3 seconds at the same time.
( is displayed.)
(Child lock can be released in the same way.)
Ice making stop
To reset the unit to the initial setting, press for 3 seconds. The setting of the refrigerator compartment, vegetable compartment, and the freezer compartment will be set to "Middle", and fast cooling operation, energy-saving operation, and cooking timer setting for all compartments will be canceled.
To use "ice making compartment" as "refrigerator compartment"
3
Press to select "ice making compartment".
? Select with switch.
Press to select "ice making compartment."
4
ON / OFF of LED for bacteria removal from water tank
to select "vegetable compartment".
Press switch and switch for 3 seconds at the same time.
( is displayed.)
Operating mode and Temperature range
Compartment Mode
Refrigerator compartment Middle
Refrigerator
Versa compartment
Chilled
Soft freezing (Middle)
Freezer
Ice making compartment
Refrigerator
Ice making
Ice making stop
Vegetable compartment
Middle
Freezer compartment
Middle
Temp range
Approx. 0 to 6
Approx. 0 to 6
Approx. -2 to 2
Approx. -9 to -5
Approx. -18 to -16
Approx. 0 to 6
Approx. -21 to -17
Approx. -21 to -17
Approx. 3 to 9
Approx. -21 to -17
Press for about 3 seconds and let flash.
After ice-making compartment is set to function as refrigerator, take ice or water out of the ice tray which are automatically dropped into ice storage bin. When ice-making function will not be used for a while, wash the water tank well with water and place it back after drying thoroughly.
To get back to "ice making", just change the temperature setting.
The temp. range left is based on the data measured at the center of each compartment with the door closed and with no food inside under the condition of ambient temperature 30 . The range varies depending on circumstances.
9
(2) Demonstration mode for shop display
Demonstration mode is not available when the temperature of freezer compartment is -7 or less even if , and are simultaneously pressed for about 5 seconds and a “beep” sound is heard. Cooling operation starts
instead.
Setting
Within 1 minute after power supply is turned on, simultaneously press , , and switch for about
5 seconds with the door of ice making compartment left open. When the setting is complete, a “beep” sound is heard and “ ” is displayed.
Panel operation mode during demonstration mode
The panel operation mode changes to “manual” if any of the switches is pressed and it changes to “auto” if none of the switches is pressed within 3 minutes after demonstration mode is set.
Manual mode: Panel indication changes according to switch operation.
Auto mode: Panel indication is automatically changed.
Release
Simultaneously press , and switch for about 5 seconds with the door of ice making compartment left open.
When the function is released, a “beep” sound is heard. “ ” disappears and the panel indication gets back to normal.
Note: Follow the procedure above to release demonstration mode as it cannot be released by simply turning on/off the power supply.
(3) Fine adjustment of temperature
Fine adjustment of temperature is available for refrigerator compartment, freezer compartment and versa
compartment.
As for versa compartment, however, it is only available when the compartment is set to or .
Setting
Press switch to select refrigerator compartment, freezer compartment or versa compartment.
Simultaneously press and for about 3 seconds until a “beep” sound is heard.
The indication changes as show in the right.
Fine adjustments of temperature
Temperature adjustment is made by approximately 0.3-0.5 by pressing and it is indicated with 15-steps bars on the panel. The temperature displayed on the panel, however, changes by 1 and might not change according to
Example of display:
In case of versa compartment
Press to make versa compartment function as refrigerator or freezer .
When the blinking marks on the display, or , are lit in 3 seconds, apply fine adjustment of temperature.
Release
Follow the same procedure as setting and the finely-adjusted temperatures are reset for refrigerator compartment, freezer
compartment and versa compartment at once.
(4) Ice making test / Self-check
This function is not available during the following modes: Child lock, Demonstration, Cooking timer, Changing the rotational speed of compressor, and Error code display.
Setting
Press for about 5 seconds.
Operation and its display
While automatic ice making is testing, the indication of ice making compartment setting blinks on LCD.
When something is faulty, the error code is indicated.
Release
The test automatically finishes in 10 minutes and the error code changes to temperature display.
(5) Thermistor temperature check mode
Setting
With the door of ice making compartment left open, simultaneously press and for about 3 seconds until a “beep”
sound is heard and “ ” blinks.
Press with the door left open.
10
Display
After the setting is complete, the kinds of thermistor and its temperature are alternately shown on the panel.
In case of abnormality, the display returns to current temperature. Please note that the temperature detected by thermistor may be a little different from the real one due to the influence of refrigerator temperature.
Kind of thermistor
Defrosting
Refrigerator compartment
Slide chilled compartment
Ice making compartment
Versa compartment
Ice making tray
Vegetable compartment
Freezer compartment
Outside air
Display
(d) (R) (C) (K) (S) (I) (V) (F) (O)
Change of display
While thermistor temperature check mode is set, press . A short beep sound is heard at each
press and the thermistor is changed in the order below.
(Ex.) When defrost thermistor reads -28 .
Defrosting Refrigerator compartment Slide chilled compartment
Ice making compartment Versa compartment Ice making tray
Vegetable compartment Freezer compartment Outside air
The defrosting thermistor is always selected first at the beginning of the setting.
Release
With the door of ice making compartment left open, simultaneously press and for about 3 seconds until a beep sound is heard. The temperature of thermistor disappears and the display gets back to current temperature.
The function is automatically released one-hour later.
Follow the procedure above to release this mode. For the protection of the compressor, avoid releasing
it by plugging and unplugging the power cord.
(6) Change mode of compressor rotational speed
Operation sound can be checked by changing the rotational speed of compressor. Always conduct a check while the compressor is operating and the “-” mark is not on the display, which shows the compressor stops. If the “-” mark is on the display, unplug the power cord and then plug it in a few seconds to operate the compressor. Also, this function is not available during the following modes: Child lock, Demonstration, Cooking timer, Thermistor temperature check and error
Setting
With the door of ice making compartment left open, simultaneously press and for about 3 seconds until a “beep” sound is heard, and “ ” blinks.
(Ex.) When the rotational
speed is 56 rps
Press with the door left open.
Changing the rotational speed
After the setting is complete, press and the rotational speed of compressor alternately changes in 10 steps.
The rotational speed (rps) is shown on the panel. Basically the compressor starts operating at level 10, however, it depends on model or specification change.
Normal
Level 0 Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7
Level 8 Level 9 Level 10
Low speed
High speed
Note: Operation sound may get increased in the process of changing the speed, but that does not mean any
problem. Check the operation sound when the rotation is stabilized.
ON and OFF of machine chamber fan motor
Under this function, fan motor in machine chamber can be switched on and off at each press of switch.
The on/off state is shown with mark on the panel.
Machine chamber fan motor
ON
Display of
Displayed
OFF Not displayed
Release
With the door of ice making compartment left open, simultaneously press and for about 3 seconds until a “beep” sound is heard. The screen returns to the temperature display.
The function is automatically released one-hour later.
Follow the procedure above to release this function. For the protection of the compressor, avoid releasing it by plugging and unplugging the power cord.
11
(7) Damper Operation Mode
During damper operation mode, the damper is forcibly opened and closed and the state of damper is shown on
the panel.
Setting
With the ice making compartment door left open, simultaneously press and for about 3 seconds until a “beep” sound is heard, and “ ” blinks.
With the door left open, simultaneously press and for about 3 seconds until a “beep” sound is heard.
Status display of each damper
Each compartment display turns on when each damper is open and turns off when each damper is closed.
Ex.) When all dampers are open;
Refrigerator compartment
Ice making compartment
Slide chilled compartment
Versa compartment
Freezer compartment
How to make each damper open or close
Although the state is shown on the panel, check airflow and confirm the damper is really opened or closed. However, air does not come out when the door is closed, so put a magnet on the door switch to simulate the condition of the door closed.
Change of display
Kind of damper
Refrigerator compartment
Slide chilled compartment
Ice making compartment
Versa compartment
Freezer compartment
(Ex.) When making the damper of refrigerator compartment open
Display
(R) (C) (I) (S) (F)
(1) Press to select the damper to be set up.
A “beep” sound is heard and the kind of damper is changed every time is pressed.
(1)Damper to
be set up
Refrigerator compartment Slide chilled compartment Ice making compartment
Versa compartment Freezer compartment
(2)" " to open,
" " to close
(2) Press to “ ” to open the damper or “ ” to close the damper.
(3) Press for about 3 seconds to convey the setting to the damper.
A "beep" sound is heard if the setting has been conveyed.
After the setting is conveyed, the damper starts operating
and the display blinks. It stops blinking and starts to light
when the operation stops automatically. Please note that the
setting cannot be changed when the damper is operating.
Slide chilled compartment damper is not mounted on this refrigerator. Although slide chilled compartment is displayed and can be set, the setting is invalid.
Release
With the door of ice making compartment left open, simultaneously press and for about 3 seconds until a “beep”
sound is heard. The screen returns to the temperature display.
This function is not automatically released.
Follow the procedure above to release this function. For the protection of the compressor, avoid releasing it by plugging
and unplugging the power cord.
12
(8) Error history display mode
Error history can be observed in the error history display mode.
Use this mode when the actual problem of the refrigerator is different from the error which was displayed at the service-call received.
Setting
Open the door of the ice making compartment, and press and together for 3 seconds until a “beep” is heard and “ ” blinks.
With the door left open, press and together for 3 seconds until a “beep” is heard.
Display details
Same as the error display and trouble locating. (Refer to 6.2(3))
When there is no recorded error, “ — ” will be displayed.
When several errors have occurred, error will be displayed in the increasing numerical
order, as in the error display and trouble locating.
(Ex.) In case errors in the ice tray thermistor ( ), refrigerator thermistor ( ) and refrigerator fan motor ( ) have occurred:
·····
Check points and resetting the error history
Follow the procedures for self-check, and take the appropriate measures.
After the self-check is completed and measures are taken, perform self-check to confirm
there is no dysfunction.
(Make sure all connectors are connected properly and there are no loose connections.)
Refer to above Setting, and activate error history display mode again.
(Ex.) When there is problem
with the ice maker gear box.
Open the ice making compartment door, and press for 3 seconds to reset error history.
When error history is reset, "-" is displayed.
Release
Open the door of the ice making compartment, and press and together
for 3 seconds until a “beep” is heard.
The display will return to the normal temperature display.
Function is automatically released in an hour.
Follow the procedure above to release this function. For the protection of the compressor, avoid releasing it by plugging
and unplugging the power cord.
Door Buzzer System :
Door buzzer has been installed so that one will not forget to close the door.
•The buzzer rings in the following conditions:
1. When door is left open.
2. When refrigerator fan motor or machine chamber fan motor is abnormal.
3. When there is possibility that the door of freezer compartment is not closed securely.
1. When door is left open Every 1 minute, for 4 minutes
After 5 minutes
2. Refrigerator fan motor or machine chamber fan motor is abnormal
3. When there is possibility that the door of freezer compartment is not closed securely
Buzzer
"Beep beep" 4 times
“"Beep beep" continuously
"Beep beep" 2 times
"Beep beep" 3 times
1. The buzzer rings to inform the open door when the door of ice making compartment, refrigerator compartment, or freezer
compartment is left open for more than one minute.
•The buzzer rings every minute. After 5 minutes, the buzzer rings continuously.
•The buzzer will stop ringing as soon as the door is closed.
•When the buzzer does not stop even if all the doors are closed, door switch may be abnormal.
•The buzzer can be stopped by the following operations.
Perform the ice making test operation.
(Note: If the test is conducted with water in the ice tray, water may fall into the ice storage bin because the tray is rolled
over in the ice making operation.)
2. Buzzer sounds when a trouble is found in refrigerator fan motor or in machine chamber fan motor. The buzzer sounds
every time the door is closed until normal operation is obtained.
(Check the error code by following the steps in Specification of display in self-check result on page 14.)
3. Buzzer sounds when there is possibility that the door of freezer compartment is not closed securely. The assumption is
made in either of the following conditions.
When the door of freezer compartment is closed, and the temperature inside did not lower after a predetermined time.
The temperature of freezer compartment is abnormally high, and the temperature of evaporator is abnormally low con-
tinuously for a long time.
Room light :
• Room light inside the refrigerator compartment lights when the door of refrigerator compartment or ice making compart-
ment is open.
• When room light is lighted continuously for more than 60 minutes, it is turned off to prevent heating.
• The protection is released when doors of refrigerator compartment and ice making compartment are closed. Then, room
light is lighted the next time at normal timing.
13
6-2 FLOWCHART OF SELF-CHECK
MR-G50M-C
(1) Troubleshooting with self-check
This refrigerator has self-check feature to clarify and indicate where & what the trouble is.
You can perform operation checks and identify malfunction of electric or electronic parts.
Error history is recorded and can be displayed by the refrigerator.
Self-check
Operate the ice-making test.
(Current displayed error: Refer to in the table below.)
The display of ice making compartment setting will blink during the test.
During the ice-making test mode, watch the operation ice-maker gear box and water pump in refrigerator.
Error history mode (Refer to 6.1(8))
Problem may recover automatically.
Perform the following if error is not displayed before treatment or the error which was displayed at the time power of the unit was turned on is not displayed.
Is error displayed?
Yes
Locate the trouble according to LED indication. (See page 15,16)
No
Set the error display mode.
Unplug the power cord from outlet.
Is error displayed?
Yes
Perform self-check procedures through .
No
Release error displayed
mode, and the self-check
is finished.
Repair /replace defective part(s) according to LCD indication.
Reset the error history.
(Refer to 6.1(8))
Self-check
Plug the power cord into outlet.
(Current displayed error:
Refer to in the table below.)
*Wait 10 minutes
before inserting
the cord once
it's unplugged.
(if the cord is
plugged in within
10 minutes, error
may be displayed.)
Yes
Is error displayed?
No
Release error display
mode and perform the
self-check again.
(go to )
Yes
Is error displayed?
Note1: Self-check cannot detect abnormalities in the following parts.
See page 19-31 for troubleshooting.
No
Was more than one error displayed during repair?
Yes
No
Perform error history mode.
Heater (Water pipe / Vegetable compartment heater, etc.)
Water pump motor
Note2: If any abnormality is found when switch is turned on, compressor and fan motor are suspended for 10 minutes.
Note3: The alarm beeps when some abnormalities (motor-locked) have occurred at the refrigerator fan motor restarts its normal operation.
Note4: If any abnormality occurs in compressor's inverter circuit, the compressor and the refrigerator fan motor stop for 10 minutes
(not only when plugging the power cord).
Was the error which was displayed when power was turned on displayed again?
Was treatment performed?
No
Perform error history mode.
Yes
Self-check is finished.
Self-check and error display method and operation
Item Operation method
Ice making test operation.
All items except (*6) listed up on the table at page
16 will be checked.
Press the switch.
for 5 seconds.
(“beep” is heard)
Power input.
All items except (*6) listed up on the table at page
16 will be checked.
Error history
Plug the power cord into outlet.
Refer to 6.2(3)
Error history display mode.
Display or self-check operation
1.Conduct the automatic ice making test.
(The display of ice making compartment setting is blinked)
2.When trouble is found, all error codes except are displayed.
3.When error is not found, nothing is
displayed.
Display time
For 10 minutes after setting.
1.When trouble is found, all trouble except
and displayed.
2.When error is not found, nothing is
displayed.
1.When trouble is found, all trouble except
and displayed.
2.When error is not found, nothing is
displayed.
For 10 minutes after power is supplied.
For one hour after setting, or until mode is released.
Others
Self-check is not available during child lock, cooking timer, changing the rotational speed of compressor, checking the temperature of thermistor, damper operation and demonstration modes.
Self-check is not available during demonstration mode.
Self-check is not available during child lock, cooking timer, changing the rotational speed of compressor, checking the temperature of thermistor, damper operation and demonstration modes.
Release of self-check display mode
Self-check finishes automatically. Error cord display is automatically released 10 minutes later.
14
(2) Timing in self-check
Trouble of Defrost heater : Self-check is conducted after defrosting.
(Make sure to confirm the display before unplugging the power cord
because it is automatically reset once the power cord is pulled out.)
Trouble of Ice maker : Press the switch on the panel for 5 seconds. (Ice making test mode.)
Trouble of Fan motor
Trouble of Inverter
The setting of ice making compartment blinks on LCD during the test operation.
: Open the door and then closed it.
When abnormality is found in fan motor, buzzer sound is heard every time the door
is closed.
: Check the error when compressor starts up or is operating.
Trouble of Thermistor : Self-check is continuously working
(3) Error display and trouble locating
1. Display details
After conducting the self-check by referring to 6-2(1), error codes are displayed in the temperature display section. ” ” and two digit error code flashes alternately as shown in the right figure.
When several errors occur, they are displayed alternately. However, the error whose code has a smaller number has priority to be displayed first.
(Ex.) In case the errors of ice tray thermistor ( ), refrigerator thermistor ( ) and refrigerator fan motor ( ) are happening simultaneously;
·····
For 2 minutes in self-check, a high-tone sound is heard due to the operation check of damper.
2. Check point and treatment
(Ex.) When ice maker gear box is defective.
Testing (*1)
Trouble
Detecting method
(*3)
Check point
(*5)
Communication error of operation panel
Ice maker is under testing
When the following communication errors occur between control board and operation P.C. board:
•They transmit and receive
data that has nothing to do
with settings.
•They cannot transmit and
receive data each other
for about 2 seconds.
1. Connector CN8K, CN7S, CN4D on control board
4-pin relay connector (hinge)
4-pin connector on operation P.C. board
2. Trouble of control board and operation
P.C. board
Repair the contact failure.
Replace
Keep the same operation as the one before the communication error has occurred.
Communication error of inverter
Trouble of ice making tray thermistor
When abnormality is found in the communication between refrigerator control circuit and inverter control circuit in control board.
(When they do not transmit and receive data for 10 seconds.)
When there is a short or open circuit in the ice making tray thermistor.
2. Check the resistance of thermistor.
Replace the control board.
Trouble of model judgement
When the model of control board is different from
1. Check the model name of control board Replace the one of operation P.C. board.
2. Check the operation P.C. board.
Replace
1. Connector CN7S on control board, Ice gear box 6-pin relay connector, 8-pin relay
connector
Repair the contact failure.
Replace
Compressor OFF.
Keep operating the unit, and conduct error code indication only.
When the compartment door has been closed for 3 hours and when freezer compartment thermistor is -10 or less, icedetecting operation starts.
Trouble of freezer compartment thermistor
Trouble of defrost thermistor
Trouble of refrigerator thermistor
Trouble of chilled compartment thermistor
Trouble of versa compartment thermistor
When there is a short or open circuit in the freezer compartment thermistor.
1. Connector CN7S on control board,
6-pin relay connector
When there is a short or open circuit in the defrost thermistor.
2. Check the resistance of thermistor.
1. Connector CN7S on control board,
2-pin relay connector
2. Check the resistance of thermistor.
1. Connector CN7S on control board,
6-pin relay connector
When there is a short or open circuit in the refrigerator compartment thermistor.
When there is a short or open circuit in the chilled compartment thermistor.
When there is a short or open circuit in the versa compartment thermistor.
2. Check the resistance of thermistor.
1. Connector CN7S, on control board,
6-pin relay connector
2. Check the resistance of thermistor.
1. Connector CN7S on control board,
6-pin relay connector
2. Check the resistance of thermistor.
Treatment
Repair the contact failure.
Replace
Repair the contact failure.
After 10 minutes off, the compressor repeats 30- minute ON and 20-minute
OFF.
The defrost heater won’t be turned ON.
Replace
Repair the contact failure.
Control
Synchronize the open/close status of R damper with that of C damper. (See page 13.)
Replace
Repair the contact failure.
Replace
Repair the contact failure.
Replace
Synchronize the open/close status of C damper with that of R damper. (See page 13.)
•When S-compartment is used as “freezer”: S-damper is open when compressor is turned on, S-damper is closed when compressor is turned off.
•When S-compartment is used other than “freezer”:
S-damper remains open for the first 3 minutes and then closed for the rest of time.
S-compartment: Versa
(select) compartment.
Trouble of vegetable compartment thermistor
When there is a short or open circuit in the vegetable compartment thermistor .
1. Connector CN7S on control board, 4-pin relay connector
2. Check the resistance of thermistor.
15
Repair the contact failure.
Replace
•
When R-damper is open,
V-heater is turned on.
•
When R-damper is closed,
V-heater is turned off.
Trouble
Detecting method
(*3)
Check point Treatment Control
Trouble of ice making compartment thermistor
When there is a short or open circuit in the ice making compartment thermistor.
1. Connector CN7S on control board, 6-pin,
9-pin relay connector
2. Check the resistance of thermistor.
Repair the contact failure.
Replace
Trouble of outside air thermistor
When there is a short or open circuit in the outside air thermistor.
Replace the operation P.C. board.
• When ice making compartment is used as “refrigerator”, synchronize I-damper with
R-damper.
• When ice making compartment is used as “ice making”, synchronize I-damper with F-damper.
Compressor is activated at
“Speed-level 2.”
Trouble of defrost heater
(*6)
When defrosting is not finished in 2 hours.
1. Connector CN2A on control board
Defrost heater plug and receptacle, 1-pin relay connector
Thermal fuse 4-pin, 8-pin relay connector
Repair the contact failure.
The defrost heater is stopped and if the next defrosting finishes in 2 hours, the error code will disappear .
Trouble of refrigerator fan motor
Trouble of machine chamber fan motor
•When motor doesn’t rotate even though power is on.
•When the waveform, which indicates the rotation times of motor, cannot be detected.
2. Check the resistance of defrost heater.
Replace
3. Check the continuity of thermal fuse.
Replace
1. Connector CN4D on control board,
Refrigerator fan motor 4-pin relay connector
2. Check refrigerator fan motor operation.
•When motor doesn’t rotate even though power is on.
•When the waveform, which indicates the rotation times of motor, can not be detected.
1. Connector CN4D on control board,
4-pin connector, 4-pin relay connector
2. Check machine chamber fan motor operation.
Repair the contact failure.
Replace
•3 minutes later, the refrigerator fan motor is reactivated to be checked.
•Until the fan motor gets to operate correctly, the buzzer sounds every time the door is closed.
Repair the contact failure.
Replace
•3 minutes later, the machine chamber fan motor is reactivated to be checked.
•Until the fan motor gets to operate correctly, the buzzer sounds every time the door is closed.
Trouble of ice maker gear box
When the gear box operation is not finished in 30 seconds.
1. Connector CN8K, CN7S on control board,
Ice gear box 6-pin relay connector, 8-pin relay connector
2. Ice gear box frozen point
Repair the contact failure.
100 minutes later, the gear box is reactivated to be checked again.
Replace
Replace
Clogging of refrigerant pipe or trouble related to compressor
(T0: Defrost thermistor temperature at power input, T1:
Defrost thermistor temperature when 15 minutes have passed from the power input)
Check the compressor and the pipe.
•When the difference between
T0 and T1 is T0 T1. (*5)
Trouble of electromagnetic twoway valve
When defrost thermistor reads -10
or above in five minutes after the compressor’s startup. (*5)
3. Check the trouble of the ice gear box with the ice making test operation.
Connector CN9D on control board
5-pin connector in machine chamber
Repair the contact failure.
When cooling operation returns to normal condition, the display of error code disappears.
Check the operation of electromagnetic two-way valve and then open the valve.
Trouble of inverter circuit
(*6)
•When there is any trouble in the circuit which detects current of compressor.
Trouble of bus- bar voltage
(*6)
•When the range of bus-bar voltage is not approx. DC 260-390V.
Trouble of inverter software reset function
•When the inverter driving software malfunctions.
Trouble of startup , synchronization or overcurrent detection
(*6)
Trouble of power supply voltage
(*6)
•When there is no current at compressor startup.
•When phase current exceeds
5.5A at compressor startup.
•When phase current exceeds 3.3A during compressor operation.
•When current of 5.3A or more runs into the bus-bar of control board.
Refer to “Compressor does not operate” at page 21.
1. Different voltage of power supply outlet When bus-bar voltage (full wave voltage) is DC 390V or above in power input.
2. Trouble of relay in the circuit on the control board
Replace the control board.
The compressor is suspended and reactivated 10 minutes later.
Refrigerator compartment room light
OFF
Heaters. OFF
Trouble of control board
(EEPROM
(*6)
related trouble)
EEPROM (IC11M) accumulates data necessary for control.
•When the data are not input accurately.
•When microcomputer cannot read the data.
Defective wiring continuity or trouble of control board
The errors to keep occurring over one and a half hour. (the situation, which compressor cannot be operated, continues.)
Overcurrent detection error occurred before the compressor is activated.
Refer to “Compressor does not operate” at page.22.
Replace the control board.
When abnormality occurs in power input, the compressor is suspended for 10 minutes.
When abnormality occurs in normal operation, the compressor keeps operating.
•Error display starts after it is regarded as .
•Error display continues until defrosting starts or cooling operation gets back to normal. (Error display doesn’t disappear by unplugging and plugging the power cord. *7)
•Try to restart compressor every 3 minutes.
*1 : The setting of ice making compartment will be displayed and blinks during or after ice making test operation.
*2 : This operation is called the recovery operation:
If the damper has not operated ever once during the compressor operation, make the damper operate when the compressor stops.
*3 : When the resistance is , the circuit is deemed open-circuitted.
When the resistance is 0 , the circuit is deemed short-circuited.
*4 : Once
is detected, other errors would be ignored and not displayed on the panel.
*5 : Characteristic value may change in order to improve the product.
*6 : The error codes to are not displayed even if those abnormalities occur at power input.
Therefore, be sure to perform ice making test operation in order to check if any abnormality indicated by these error codes occurs. (See page 14.)
*7 : If those errors still continue for 1 minute after the restart, will be displayed again.
16
6-3 BLOCK DIAGRAM OF PRINTED CIRCUIT BOARD
MR-G50M-C
Operation P.C. board
•Setting up temperature, feature, quick mode and eco mode for each compartment
•Display of self-check
•Outside air thermistor
•Buzzer
Control board
Control circuit of refrigerator
•Read/control each compartment temperature (Neuro-fuzzy)
•Control on timers
•Operation control of the parts such as fan motor or heater, etc. equipped inside/
outside
Inverter control circuit of compressor
•Inverter control of compressor
•Inverter-drive power module
•Detection of bus-bar voltage
Parts outside/inside of refrigerator
For 311V system
•Compressor
For 110V system
•Defrost heater
•Vegetable compartment heater
1&2
•Rotational heater board
•Divider heater (I/S)
•Water pipe heater
•Refrigerator compartment room light
•Ice making tray heater
•Tank heater
•Duct heater
For 12V DC system
•Refrigerator fan motor
•Machine chamber fan motor
•Motor damper
•Ice maker gear box
•Two-way valve
•Photosynthesis LED
UV LED
Blue LED
•LED for bacteria removal from
water tank
6-4 AUTO ICE-MAKER
MR-G50M-C
(1) Ice making cycle
Water supply
The ice tray is filled with water from the water tank.
For 5V DC system
•Freezer compartment thermistor
•Refrigerator compartment thermistor
•Defrost thermistor
•Slide chilled compartment thermistor
•Door switch (For refrigerator compartment & ice compartment & freezer compartment)
•Ice tray thermistor
•Ice making compartment thermistor
•Vegetable compartment thermistor
•Position-specifying switch in ice maker gear box
•Versa compartment thermistor
Ice stock
Ice tray thermistor watches and controls the ice making operation
(2) Automatic ice maker circuit
Ice ejection
After the detection lever checks the amount of ice, the ice tray is rolled over for ice ejection.
Ice stock
Ice is stocked in the ice server.
Ice making capacity is about
100 - 120 cubes a day.
Stock capacity of Ice cubes is about 100 cubes.
(With 8-cube ice tray)
CN3A
Tank heater
CN4D
CN2A
CN7S
Water pipe heater
LED for bacteria removal from water tank
8-pin connector
6-pin connector
Water pump motor
6-pin connector
Ice making compartment thermistor
CN9D
CN8K
Ice tray thermistor
Ice making gear box
8-pin connector
17
6-pin connector
(3) Operation by ice making test
Press the switch for 5 seconds or more.
(See “• Self-check and error display method and operation,
Ice making test operation” at page 14.)
Ice stock detective lever detects the amount of ice.
Detective lever once come down to detection point then return to the original position.
The ice tray is rolled over and the system is reset.
The ice tray rolls over once to drop the ice, then return to the original position.
Water pump motor is operates.
Remove the lid of the water tank then check the sounds of water running.
Completion
When abnormality occurs, the error code is displayed on the panel.
Inspect the abnormal points by referring to page 15, 16.
Ice making test completes about 20 seconds later.
Ice tray
Detection lever
(Upper freezer compartment)
Check here.
(Lower-left part of refrigerator compartment)
[Check point of automatic ice maker operation]
*Never touch the automatic ice maker while it is operating.
After the operational test, a popping sound is heard several times because the operation of two-way valve is checked automatically. During the operation, do not insert a hand into the automatic ice maker.
(4) Maintenance for water pump and water pipe
Water pump & Light-type bacteria removing filter
1. Pull out the pipe. 2. Turn the tank
Water tank
Tank pipe
pump to detach.
Water pump
Water pipe · Tank holder
Light-type bacteria removing filter
4. Remove the light-type bacteria removing filter
3. Pull out the tank pipe, turn the cap
to remove, and then wash
the propeller with water.
•The propeller is
made of the magnet.
Wash it well with water
so that no alien sub-
stance remains on it.
and wash it in water.
Normally the filter need not be replaced. However, replace it
in the following condition:
•When the filter is clogged by passing something other than
Tank pipe
Propeller
Cap
water through the filter.
•When the filter is broken.
Cover
In such a case, contact the dealer that you purchased this
refrigerator.
5. Put the parts back in the reverse order of disassembly.
1. Pull out water supply
Water
2. Separate pieces and wash with water.
3. Reverse steps to replace the pipe.
pipe. Wipe the tank
holder with clean cloth.
•Do not let water flow into
the tank holder.
supply pipe
Tank holder
(5) Troubleshooting for automatic ice-maker
packing Aluminum pipe
•Twist the
aluminum
pipe to
replace it.
Side A
Side B
Water pipe
•Replace the water
pipe.
Be sure that sides A
and B fit flush to
each other.
Water in the tank holder
Chained ice, water leaking from the ice server
The ice-maker gear box may be defective, cooling may be poor or ice cubes may be full in the server.
1. Check inside of the ice server.
•Ice cubes are not stored flatly and the amount is detected as full.
•Food inside the ice server
2. Measure the resistance of ice tray thermistor circuit. •Open circuit ( ) or
short circuit (0 )
•Not enough 3. Check if the temperature of the freezer compartment is cool enough.
(It takes longer to make ice during summer time
or if the door is frequently opened.)
The water saucer may be defective, or the ice tray may get cracked.
Inspection
Replace the ice tray thermistor.
Poor cooling
4. Check the water pipe between the refrigerator compartment and freezer compartment for dirt, and foreign objects.
5. Check the condition of ice tray.
6. Disassemble the water pump and check the inside of the pipe.
7. Tank pipe is clogged , has a hole or is not
•Clogging
•Freezing (For freezing, check installation and measure the resistance of water pipe heater and tank heater.)
•Broken or cracked
•Not placed properly
•Dirt or foreign objects
•Clogging, disconnecting
•Hole or crack
Clean the water pipe.
Defrost
Check continuity of water pipe heater and tank heater.
Replace the tray.
Reinstall it properly.
Repair and explain to the user for proper usage.
Clean / Reinstall it properly.
Change the tank pipe.
Check the water pump.
Change the water tank.
8. Check the motor coil resistance.
•Open or short circuit
9. Check if there are any dirt or foreign object which are difficult to remove in the water tank. Also, check if there is any crack or deformation on the tank.
•Crack or deformation
10. Check the water pipe for dirt, and foreign objects.
Also, check the water pipe position and connection.
•Clogging, disconnecting
•Hole or crack
11. Check the water pipe (between F.compartment and •Clogging
R.compartment) for clogging.
12. Check the water pump operation by the ice-making •Water filling time is longer test than 9 seconds.
Clean / Reinstall it properly.
Replace the pipe.
Clean / Remove the dirt.
Replace the control board.
13. Water spill at the installation of water tank or more water over the full water level may cause to from chained ice.
14. Measure the water pump coil resistance.
•Open or short circuit Change the water pump motor.
18
6-5 FLOWCHART OF TROUBLE CRITERION
MR-G50M-C
Excessive cooling No cooling, poor cooling
Are the temperatures of refrigerator compartment/ set to “Low”?
No
Set the temperatures to “Low”.
Are the temperature of refrigerator compartment/ set to “High”?
Yes
No
Set the temperatures to “High”.
Yes
Only food around the air blowing part get frozen
No
Yes
Keep the food away from the blowing part
Open the refrigerator compartment door with a magnet on the door switch to check that cold air blows from the outlet.
(See 1)
Yes
No
Proceed to [5] at page
23.
Expose the damper (for refrigerator compartment/ slide compartment) so that its operation can be visibly checked and conduct an ice-making test. Does the baffle open/close ?
(Wait 1 minute for self-check).
(See “Self check method and its operation, Ice making test operation” at page 14.)
Normal
The baffle does not operate
Yes
Is the motor damper (for refrigerator compartment/ slide compartment) covered with frost?
No
Check the refrigerator compartment thermistor
Put refrigerator compartment thermistor into ice water (0 ), disconnect the 4-pin connector, and measure resistance between
(white) and (white).
•
Resistance at 0 :approx. 6-7k .
Refrigerator compartment thermistor abnormal
Replace the motor damper (for refrigerator compartment/ slide chilled compartment)
Motor damper is combined with
control panel assembly.
Repair the frosted part.
Replace the refrigerator compartment thermistor
Check the chilled compartment thermistor
Put chilled compartment thermistor into ice water (0 ), disconnect the 6-pin connector, and measure resistance between
(white) and (white).
•
Resistance at 0 :approx. 6-7k .
Chilled compartment thermistor abnormal
Replace the slide chilled compartment thermistor
Adjusting set temperature by cutting pattern jumpers
•By cutting the pattern jumper of temp. control board, set temperature for each compartment can be changed.
•Pattern jumper is located at the position indicated in the fi gure below, on the temp. control board.
To change the set temperature, cut out the corresponding pattern together with the board.
1
Refrigerator compartment
Caution
•Make sure to unscrew the back of operation panel and remove the decoration panel before cutting the pattern jumper.
•To cut the board, use a nipper or a cutter. Be careful not to damage the surrounding patterns.
•When cutting out the pattern jumper, cut so that the white hatched area behind the board is cut out.
•After cutting, remove the cut out board pieces, and install it to the control panel.
Ice making compartment
Versa compartment
Attach a magnet bar here.
Front side
Pattern jumper
Back side
White hatched area
Weak
Refrigerator compartment
Slide chilled compartment
Low
Cooling
Middle
Strong
High Chilled
Refrigerator
Chilled
CN7S
19
6
-pin connector
Refrigerator compartment thermistor
Slide chilled compartment thermistor
Poor cooling
1
Is the set temperature of freezer compartment set to “High”?
Yes
2
3
Does cool air come out of air outlet when opening the refrigerator compartment door and attaching a magnet bar on the door switch ?
Yes
Operate the ice-making test at the place where the operation of dampers (Refrigerator compartment and slide compartment thermistor) is visible. Does the baffle open / close? (Wait 1 minute for self-check).
(See “Serf-check and error display method and operation, Ice making test operation” at page 14.)
Normal
No
No
Set the temperature to “High”.
Proceed to “The refrigerator fan motor does not work.”
The baffles do not function.
Replace the motor damper (for freezer compartment ).
Replace the fan grille as well as the motor
damper since they are combined together.
Normal
When compressor operates, LCD indicates as a result of self-check.
Exchange the unit
4 Check freezer compartment thermistor.
Dip freezer compartment thermistor into ice water (0 ), and measure the resistance between terminal (white) and
(white) by detaching 6-pin connector at the left-back bottom of vegetable compartment.
•
Resistance at 0 :approx. 6~7k .
Defective thermistor
Replace freezer compartment thermistor
CN7S
CN4D
8-pin connector
Freezer compartment
thermistor
M
Motor damper
(for freezer
compartment)
Not cooling at all (In case any error codes doesn’t appear as shown in page 21,22 even though mode switch is pressed for 5 seconds)
Yes
Is refrigerator in the demonstration mode?
No
Does AC 110V run between and , terminals of CN1 on filter board?
No
Release the demonstration mode. (See page 10.)
Inspect power-supply wiring such as power cord and breaker etc.
Yes
Does AC 110V run between and , terminals of CN2 on filter board?
No
Replace the filter board.
Yes
Detach each connector CN2A on control board check the continuity between terminals and respectively.
(Check if there is a short or open circuit in the motor protector.)
Continuity detected
No continuity
Detach connector CN50G on control board and check the resistance respectively between terminals of
, and :approx. 9.3
No continuity
Continuity detected
Motor protector (open circuit)
By measuring the resistance,
ensure that the circuit is open.
Abnormal
Disconnect 6-pin connector in machine chamber to check resistance between terminals of
, and : approx. 9.3
Abnormal
Normal
Check connector contact.
Abnormal
Check the error display of selfcheck after turning on and off the power supply.
With all the connectors connected.
Measure the resistance of compressor’s winding between terminals of black, white, and red : approx. 9.3
Exchange the unit
6-pin connector in machine chamber
Normal Replace the lead wire assembly (Lead wire of compressor)
Inverter-related parts may be defective. Conduct ice making test operation. (See page 21 for error codes.)
M
Compressor
M
Motor protector
CN1
Filter board
CN2
Noise filter
CN2A CN50G
Control board
20
Inverter-related indication “Compressor does not operate”
Error code
Abnormality Possible cause Symptom
Trouble of inverter circuit
Bus-bar voltage is abnormal.
Treatment
•When there is
any trouble in the
circuit which
detects phase
current of com-
pressor.
Compressor does not rotate.
•Power supply
voltage is
abnormal.
Compressor does not rotate.
Replace the control board.
•Defective reactor
on the N/F board
Start
Measure the voltage of power supply.
80V or more
Arrange power supply to obtain the rated voltage,
90~130V.
280V or more
Arrange power supply to make the voltage within 90~130V and conduct the following checks.
Does AC110V run between CN51 terand , on the control board?
(See page 32.)
No
Check the connection between filter board and control board.
Abnormal
Connect them properly.
Yes
Replace the control board.
Normal
Replace the filter board.
Trouble of •When the inverter inverter software driving software reset function malfunctions.
Compressor does not rotate.
Unplug the power cord and then plug it in 10 minutes.
Check the error code by performing the ice making test operation.
display again.
No error code display
Replace the control board.
Explan to customer
•Abnormal start-
up
•Compressor
motor gets locked.
•Defective circuit
on control board
Compressor does not rotate.
•Abnormal
synchronization
•Trouble of
overcurrent detection
•Defective contact
of CN50G on
control board
•Defective contact
of machine
chamber 6-pin
connector
Start
Disconnect 6-pin connector in machine chamber to check resist-
No ance between each terminal of
, and : Are they approx. 9.3
(20 )?
Yes
Measure the resistance of compressor’s winding between each terminal of
, and : Are they approx. 9.3
(20 )?
No
Yes
*Replace lead wire assembly C.
Exchange the unit.
*Is compressor
No
energized at
startup?
Yes
Exchange the unit.
Check the connection of the connector CN50G on the control board or the machine chamber 6-pin connector.
Abnormal
Normal
Connect them properly.
Replace the control board.
*If control board is normal, compressor is energized
every 10 minutes.
Compressor vibrates at startup when it is being ener-
gized. Touch it with your hand to check.
21
Inverter-related indication “Compressor does not operate”
Error code
Abnormality
Possible cause Symptom
•Defective wiring
•Defective concontinuity
•Trouble of the control board nection of connectors
related to compressor (boardside,relay, compside)
•Defective wiring continuity of the compressor
•Trouble of control board
•Trouble of compressor
(1) or (2)
(1) Compressor cannot be activeted for more than
1.5 hours
(2) Overcurrent detection error occurred before the compressor is actived.
start
Connector CN50G on the control board is properly connected?
Yes
Treatment
1. Locate the trouble and decide the treatment
•Decide the treatment by checking the followings.
(1) Defective connector connections.
(board-side, relay, comp-side)
(2) Resistance of compressor’s winding
2. Flowchart of troubleshooting
No
Check Treatment
Connect properly.
6-pin relay connector in machine chamber is properly connected?
No
Compressor
6-pin relay connector in machine chamber
Point+2 (to measure resistance)
For checking the connection to compressor
Lead wires connected to compressor
Point+1 (to measure resistance)
For checking the relay connection
Control board
Yes
The connector of compressor
is properly connected?
Yes
Disconnect 6-pin relay connector in machine chamber and measure the resistance between each terminal of , and (Pont 1).
Approx.
No
No
No
Exchange the unit
Yes Yes
Replace the lead wire connected to compressor.
Is compressor being energized at startup?
No
Replace the control board.
Yes
Exchange the unit
Replace it only when error display keeps blinking even though all the above mentioned connectors are
properly connected.
3. Recheck after treatment
•After any treatment is tried, unplug and plug power cord again to check if the compressor operates properly.
•If the compressor can operate properly for more than 1 minute after power cord is plugged again, it’s presumed that the cause of trouble is eliminated.
*If the cause of trouble cannot be eliminated," " will be displayed again 1 minute later after the power cord is plugged again.
*If the control board has been replaced, won’t be displayed even though the cause of trouble is still not eliminated. In such a case, perform the ice making test operation to check what the error is. At the same time, also confirm that the compressor is operating for more than 3 minutes and each compartment is getting cooled.
22
Poor cooling
1
Short-circuit the terminal and of the compulsory defrosting terminals (CN1M) of the filter board to actuate the compulsory defrosting function and check whether the defrost heater is working properly. *1
No
No 2
Check if there is continuity between thermal fuse and defrost heater.
Yes
Yes (heats up)
Check the following: half-open door, space between gaskets, the amount of ice.
Replace the defrost heater and the thermal fuse.
Check the resistance of the defrost thermistor.
CN7S
CN2A
4-pin connector
9-pin connector
Thermal fuse
1-pin connector
Defrost heater
Defrost thermistor
2-pin connector
<Control board>
Short circuit
CN1M
Compulsory defrosting
1
*1 The compulsory defrosting will not work when the temperature of the defrost thermistor is 14: or more.
1
Plug and unplug the power cord to perform self-check on refrigerator fan motor. Is the lamp indicating abnormality?
Yes
Replace refrigerator fan motor.
No
Note: Refrigerator fan motor is combined
with fan grille.
2
3
Plug and unplug the power cord to check if machine chamber fan motor is rotating.
Running
Check the door switch for continuity.
•Open and close the refrigerator door several times
and check if the room light will be turned on and off
(Room light should get turned off when the door comes
10mm close to the refrigerator body .)
•Close the refrigerator compartment door until the light is
turned off . Open and close the ice-making-compart-
ment door , and from the space of refrigerator compartment door, check that the room light is turned on and off.
Not rotating
Check if CN4D connector on control board is connected properly.
If it is, replace the control board.
Room light is not turned on and off.
4
Check the continuity by disconnecting the CN7S on the control board. (See figure below.)
Normal
Abnormal
Contact failure of connector.
Connect it properly.
Check if the connector on the door switch is connected properly. If it is, replace the door switch.
Room light is turned on and off properly.
5
Check if there is continuity in 6-pin fan motor connector in versa compartment.
No continuity
Connect the connectors properly.
Continuity detected
Door switch for refrigerator compartment (right and left) and ice making compartment.
Doors
Any one of the doors are open
R-door (right, left): closed
Door of the ice making compartment : closed
Replace refrigerator fan motor.
Note: Refrigerator fan motor is combined
with fan grille.
If any one of those doors are open, the switch between
and , terminals of 2-pin connector, will be OFF) etc 1 2
2-Pin connector
Between
1 and
2
OFF ON
CN7S
8-pin connector
Lead Switch board
3-pin connector
Refrigerator compartment
(right and left)/ Ice making compartment door switch
10~50mm
2-pin connector
Freezer compartment door switch
Right door of refrigerator compartment
CN4D
6-pin connector 4-pin connector
Refrigerator fan motor
Left door of refrigerator comparttment
Door of ice making compartment
Door of versa compartment
Door of vegetable compartment
Door of freezer compartment
23
Excessive cooling poor cooling
Is the temperature of vegetable compartment set to “Low”?
No
Yes
(Go to or )
Set the temperature to
“Low”.
Is the temperature of vegetable compartment set to “High”?
Yes
No
Set the temperature to
“High”.
Check the thermistor, vegetable compartment heater, and control board.
Is 1 of these error codes indicated when conducting self-check of operation P.C. board?
No
(Go to or )
Are the temperatures of refrigerator compartment/ freezer compartment set to “Low”?
Yes
Set the temperatures to
“Middle” or “High”.
Refrigerator compartment thermistor:
Slide chilled compartment thermistor:
Vegetable compartment thermistor:
Outside air thermistor:
When the vegetable compartment is cooled excessively.
Is there voltage AC110V between connector CN2A (Gray) and
CN3A (Yellow green) on control board? Measure the voltage for over 10 seconds. When an analog tester detects 110V, consider the control board normal. (110V is outputted every 10 seconds.)
is indicated.
Yes
No error code is indicated.
Is there a short or open circuit in each thermistor and is the resistance 0 or ?
No
Is there resistance of 2k on the wiring side (resistance of vegetable compartment heater 1) between connector
CN3A control board with 2-pin connector disconnected?
Yes
and CN2A on
0 or
Is there a resistance of approx. 2k between and , terminals of 8-pin connector which is located at the right top of fan grille?
Yes
It may have contact failure of connector.
Recheck the contact after the 8-pin connector is connected.
Yes
0 or
0 or
Is there resistance of 1k on the wiring side (resistance of vegetable compartment heater 2) between connector CN3A and CN2A
on control board with 8-pin connector disconnected?
Replace the Filter board.
Replace the defective thermistor.
Is there a resistance of approx.
1k between and , terminals of 2-pin connector which is located at the left-back bottom of vegetable compartment?
0 or
Check the contact of connector connecting each thermistor and connector
CN7S on control board. Fix the incomplete contact.
Replace the vegetable compartment heater 1.
Note: Vegetable compartment
heater 1 is combined with
fan grille.
Replace the vegetable compartment heater 2.
Note: Vegetable com-
partment heater 2
is combined with
partition V/ F.
Yes
Check if doors are hermetically closed.
No
Replace the control board.
Check refrigerator / slide chilled compartment is excessively cooled (poorly cooled).
Follow the refrigerator / slide chilled compartment flowchart on page 19.
OK
Explain proper usage to customer
6-pin connector
Slide chilled compartment thermistor
Refrigerator compartment thermistor
CN2A
8-pin connector
CN3A
CN7S
2-pin connector
Vegetable compartment heater 1
Vegetable compartment heater 2
CN8K
5-pin connector
Operation P.C. board
Outside air thermistor
TH1
CN4D
24
only applies to versa compartment.
Excessive cooling No cooling; poor cooling
It is set to
“Vegetable •
Refrigerator” or
“Chilled”.
Yes
No
Which operation mode is versa compartment set to?
It is set to “Soft freezing”.
Only the food around
Is the motor damper covered with frost?
Not frosted
Is the temperature set to “Low”?
cool-air outlet is excessively cooled.
Yes
No
Set the temperature to “Low”.
Keep food away from air outlet in storing food.
Make the operation of motor damper (for ice making compartment/ refrigerator compartment) visible, and conduct ice making test. Check that the baffles open and
The baffles do not function close.
(Wait 1 minute for selfcheck.)
(See “• Self-check and error display method and operation, Ice making test operation” on page
14.)
Is connector CN9D on control board connected properly?
Yes
Disconnect CN9D and measure the resistance between and , and between and .
Check that the winding of motor damper (for ice making compartment/ versa compartment) has a resistance of approx. 415
No
0 or
Normal
Normal
Frosted
Which operation mode is versa compartment set to?
It is set to ,
“Vegetable •
Refrigerator” or
“Chilled”.
Is the temperature set to “High”.
No
It is set to “Soft freezing”.
It is set to “Freezer”.
Set the temperature to “High”.
Yes Check the set temperature in freezer compartment. Is the temperature set to “High”?
1
Does cool air come out of air outlet when opening the refrigeratorcompartment door and attaching a magnet bar on the door switch?
Yes
No
No
Set the temperature to
“High”.
Refer to the section:
“The refrigerator fan motor does not work”.
Connect the connector properly.
No
Is 6-pin connector which is in connector cover on the back of versa compartment connected properly?
(6-pin connector is connected to motor damper.
Refer to the figure below.)
Yes
Replace the motor damper (for ice making compartment/ versa compartment)
Replace the fan grille as well as the motor
damper because they are combined together.
Repair the frosted part.
Check the versa compartment thermistor.
Dip the versa compartment thermistor into the ice water
(0 ) and disconnect 6-pin connector for fan grille at the back of versa compartment. Measure the resistance between terminal (white) and (white).
•
Resistance at 0 : Approx. 6~7k
Check the ice making compartment thermistor.
Dip the ice making compartment thermistor into the ice water (0 ) and disconnect 6-pin connector of fan grille at the back of ice making compartment. Measure the resistance between terminal (white) and (white).
•
Resistance at 0 : Approx. 6~7k
6 -pin connector
CN4D
Defective thermistor
6 -pin connector
Replace the ice making compartment thermistor.
Motor damper
(for refrigerator compartment/
ice making compartment)
M
CN7S
Ice making compartment thermistor
1
Refrigerator compartment
Attach a magnet bar here.
CN9D
6
-pin connector
Defective thermistor
Versa compartment thermistor
Replace the versa compartment thermistor.
Ice making compartment
Versa compartment
M
Motor damper
(versa compartment)
25
6-6 TROUBLE CRITERION OF MAIN PARTS
MR-G50M-C
Components/
Part Name
Check Method and Criterion
Compressor
Black
Model
EFI100E13DAH
Rated input
Starting current
Running current
W
A
A
45/159 (1620/4800rpm)
2.0
0.63/2.19 (1620/4800rpm)
White
Red
Normal
Abnormal
(faulty)
Measure the resistance with a tester.
Winding
(Black-White)
(White-Red)
(Red-Black)
9.3
(20 )
Open ( ) or short circuit (0 )
Motor protector
Model MM3-71CCV
Connected point
Open
100 ± 50 or more
Energize it at 17.0A, 25 for 16 seconds at the longest.
Close 61±8 or less
Measure the resistance with a tester. (Ambient temperature : Room temperature)
Parts Mounted
Position
In the machine chamber at the rear side of the frame.
In the machine chamber at the rear side of the frame.
1
Contact point
2 Normal
Less than 1
Abnormal (faulty)
Open circuit (
0
)
Refrigerator fan motor
Machine chamber fan motor
1
2
Model
Number of pole
Diameter
UDQM002B3
DC brushless
10
150 (Mixed flow fan)
Measure the resistance with a tester. (Ambient temperature : Room temperature)
Normal
Abnormal
(faulty)
Between and (GND and IC
Power): About 12k
IC Power):
: open circuit ( )
Between and
:short circuit (0 )
2
1
4
3
IC Power
Power
FG
GND
IC
1 2 3 4 : Pin No.
Model
Number of pole
Diameter
Operation method
UDQM004B3
DC brushless
10
140 (Extra fan)
During compressor operation
Measure the resistance with a tester. (Ambient temperature : Room temperature)
Normal Abnormal (faulty)
4
3
2
1
IC Power
Power
FG
GND
IC
Between and (GND and IC
Power): About 9k
Between and
: open circuit ( )
1 2 3 4 : Pin No.
Between and (Power and
IC Power):
:short circuit (0 )
26
In the fan grille of the freezer compartment.
In the machine chamber at the rear side of the frame.
Components/
Part Name
Water pump motor
Check Method and Criterion
Measure the resistance with a tester. (Ambient temperature : Room temperature)
Normal
16 (Approx.)
Abnormal (faulty)
Open ( ) or short circuit
(0 )
Motor damper for refrigerator compartment/ ice making compartment
Measure the winding resistance.
Winding
(
Blue-White
Red-Yellow
)
Normal
415
(Approx.)
Red
Abnormal (faulty)
Open ( ) or short circuit
(0 )
Parts Mounted
Position
Under the water tank holder in refrigerator compartment.
In the fan grille for freezer compartment.
Connector is at the left-back bottom of refrigerator compartment.
Motor damper for versa compartment
Measure the winding resistance.
(
Winding
Blue-White
Red-Yellow
)
Yellow
Normal
415
(Approx.)
Red
Blue White
Abnormal (faulty)
Open ( ) or short circuit
(0 )
In the fan grille for freezer compartment.
Connector is at the back of versa compartment.
Motor damper for freezer compartment
Measure the winding resistance.
Winding
(
Blue-White
Red-Yellow
)
27
Yellow
Normal
415
(Approx.)
Red
Blue White
Abnormal (faulty)
Open ( ) or short circuit
(0 )
In the fan grille for freezer compartment.
Connector is at the left-back bottom of vegetable compartment.
Yellow
Blue White
Components/
Part Name
Defrost heater
Check Method and Criterion
Rated input
W
Operation method
150
The heater is energized while defrosting.
(Defrosting is finished when the evaporator is 14± 1.5 or more)
Measure the resistance with a tester. (Ambient temperature : Room temperature)
Parts Mounted
Position
At the drip tray under the evaporator of the freezer compartment.
Normal
81
(Approx.)
Abnormal (faulty)
Open circuit ( )
Vegetable compartment heater 1
Measure the resistance with a tester. (Ambient temperature : Room temperature) In the fan grille at the back of vegetable compartment.
2k
Normal
(Approx.)
Abnormal (faulty)
Open circuit ( )
Vegetable compartment heater 2
Operation method
The heater is turned on when vegetable compartment thermistor has reached a lower temperature than the set temperature for vegetable compartment.
Measure the resistance with a tester. (Ambient temperature : Room temperature)
In partition V/F.
Normal
1k (Approx.)
Abnormal (faulty)
Open circuit ( )
Water pipe heater
Operation method
The heater is turned on when vegetable compartment thermistor has reached a lower temperature than the set temperature for vegetable compartment.
Measure the resistance with a tester. (Ambient temperature : Room temperature)
Under the water tank holder.
Normal
2.1k
(Approx.)
Abnormal (faulty)
Open circuit ( )
Operation method
When ice-making thermistor has reached approx. 10 or below, the heater is turned on with energizing rate adjusted by the set temperature of refrigerator compartment and freezer compartment.
28
Components/
Part Name
Divider heater (I/S)
Check Method and Criterion
Measure the resistance with a tester. (Ambient temperature : Room temperature)
Parts Mounted
Position
In partition I/S
Normal
3.9k
(Approx.)
Abnormal (faulty)
Open circuit ( )
Rotational heater board 1
Operation method
While compressor is operating, the heater is turned on.
When compressor stops, the heater is suspended for the first 20 minutes and then reactivated.
Measure the resistance with a tester. (Ambient temperature : Room temperature)
In the rotational heater board of refrigerator compartment
Normal
1.5k
(Approx.)
Abnormal (faulty)
Open circuit ( )
Ice making tray heater
Operation method
While compressor is operating, the heater is turned on.
When compressor stops, the heater is suspended for the first 20 minutes and then reactivated.
Measure the resistance with a tester. (Ambient temperature : Room temperature)
Lower part of ice tray
Normal
1.2k
(Approx.)
Abnormal (faulty)
Open circuit ( )
Duct heater
Operation method
During CRYSTAL ICE mode
(The heater is turned on 5 minutes after water is
supplied, until 4 hours.)
Measure the resistance with a tester. (Ambient temperature : Room temperature)
In the fan grille for freezer compartment
Normal
3.9k
(Approx.)
Abnormal (faulty)
Open circuit ( )
Operation method
Synchronised to defrost heater operation. (The heater is turned on during defrost operation.)
(The heater is energized while defrosting.)
29
Components/
Part Name
Tank heater
Check Method and Criterion
Measure the resistance with a tester. (Ambient temperature : Room temperature)
Parts Mounted
Position
Under the water tank holder.
Normal
3.9k
(Approx.)
Abnormal (faulty)
Open circuit ( )
Thermistor
Two-way valve
Operation method The heater is controlled by duty factor increase/ decrease.
Measure the resistance with a tester according to the following graph.
(Thermistor resistance values against temperature)
•Resistance measured under the ambient temperature from -50 to +50
1. 200 to 500k •••••••••••••••••••Normal
2. Out of the above range •••••••••Abnormal
35
30
25
20
Refrigerator
compartment
Slide chilled
compartment
Ice making tray
thermistor
Thermistor resistance values against temperature
Freezer
compartment
Defrosting
Versa
compartment
Ice making
compartment
Vegetable
compartment
Outside air thermistor
(In the operation
P.C. board)
Defrost
thermistor
Evaporator with the change of temperature.
Ice making
Thermistor Check Procedure
•Thermistor resistance value will vary
thermistor,
Versa
compartment
•Take the temperature around the
thermistor,
thermistor, and then measure thermistor
Vegetable
resistance using a tester.
compartment
The relation between resistance and
thermistor
temperature is as shown on the left side.
Troubleshooting with self-check
(1) If the self-check indicates the abnormality of thermistor when the power is
and Freezer
compartment
thermistor
In the fan grille
of each
compartments.
15
10
5
0
-20
Inner thermistor
-10 0 10
Temperature
20 30 turned on, measure the resistance of the thermistor.
•If there is a short circuit in the thermistor, there may be a defect in the contact of the connector or the element of the thermistor.
(2) When the self-check indicates the abnormality of thermistor a few seconds after the power is turned on, check the contact of the connector.
Ice making
tray
thermistor
In the ice
making
compartment.
Outside air
thermistor
In the operation
P.C. board.
A 5
A 2
Model NSCE000DA1
In the machine chamber at the rear side of the frame.
1
B
3
COM
4
B
Normal
54~56 (Gray
[common] A/ A/ B/
B each phase)
Abnormal
Open ( ) or short circuit
(0 )
1 2 3 4 5
B A COM B A
Check the operation of two-way valve
Check the operation by following either (1) or (2) below. When a popping sound is heard 1 to 25 times, it is considered that the valve is operating normally. The sound is clearly heard around the back of the product.
(1) Reset the power supply. Check the operation right after this.
(2) Ice making test. Check the operation right after the test is over.
30
Components/
Part Name
LED for bacteria removal from water tank
(12V DC)
Check Method and Criterion
Timing in making contact
Abnormal condition
•After water is supplied to the ice tray.
•After the ice level sensor lever detects that ice storage
becomes full.
•While the door is kept open for maximum of 5 minutes.
When the door is opened, LED goes out within 5 minutes.
Make sure if the connector is securely connected.
LED
Note: LED cannot be replaced individually because
it is embedded in the tank holder.
Vegetable compartment photosynthesis, UV
LED, Blue LED
(12V DC)
Timing in making contact
Photosynthesis LED 3 pieces + UV LED 1 piece + Blue LED 1 piece
Photosynthesis
LED
UV LED
Blue LED
Always
After water is supplied, and full ice is detected; When the door of refrigeration compartment, ice making compartment, or freezer compartment is open. (5 minutes maximum)
Abnormal condition
Means
Photosynthesis
LED
UV LED
Blue LED
LEDs light in following colors at the above timing.
Photosynthesis LED: Orange
UV LED: Bluish white
Blue LED: Blue
Check with the diode range( tester equipped with diode range.)
) of tester. (Use a
The pointer of the tester does not shake when measuring between 4-pin connector No.1 (-) and No.2 (+). Make sure the pointer of the tester does not shake even if the polarities are reversed. Resistance: Short-circuited (0 )
The pointer of the tester does not shake when measuring between 4-pin connector No.3 (+) and No.4 (-). Make sure the pointer of the tester does not shake even if the polarities are reversed. Resistance: Short-circuited (0 )
Note: LED cannot be replaced individually because it is combined with the fan grille and partition
V/F.
Photosynthesis
LED
UV LED
Blue LED
UV/Blue Photosynthesis
Use a tester equipped with a diode range
Parts Mounted
Position
On the external surface of the tank holder
On the ceiling vegetable compartment
(Vegetable
compartment
LED board)
6-7 TEST POINT DIAGRAM OF FILTER BOARD
MR-G50M-C
Earth
4 3 2 1
AC110V
110V
31
6-8 TEST POINT DIAGRAM OF CONTROL BOARD
MR-G50M-C
CN50G
Compressor
DC +5V
(Inverter circuit)
DNG
DC280 ~ 330V
– +
– +
DC+12 ~ 20V
(Inverter circuit)
– +
CN2A
7
5
AC
110V
~
3 Defrost
heater
1 Duct heater
CN3A CN9D
CN4D
CN8K CN7S
Compulsory defrosting by short circuit
–
+
DC+5V
(Refrige-
rator
control
circuit)
–
+
DC+12 ~
13V
(Refrige-
rator
control
circuit)
32
7 NAMES OF THE PARTS
MR-G50M-C
Operation panel
Fast cooling button
MODE button
SELECTION button
ECO button
Refrigerator compartment
AUTO-Shelf
Two-way flexishelf
Free pocket (S)
Small item case
Free egg shelf (S)
Bottle pocket (S)
Water tank
Automatic ice maker
(Ice making compartment)
Ice making compartment is applicable to refrigerator and freezer compartment.
Vegetable compartment
Free pocket (L)
Lid of slide chilled case
Slide chilled case
Tube stand
Bottle pocket (L)
Alumi-num tray
Versa compartment
Versa compartment is applicable to freezer, soft freezing, chilled and refrigerator
Versa compartment is set to soft freezing mode at factory shipping.
Water tank (app. 1.2L)
Water supply port cap
Water tank lid
Pipe
Water supply pump,
Light-type bacteria removing filter
Water supply pipe
Ice storage bin
Ice server
Freezer compartment
Slide case
Vegetable case
Versa case
V-LED lamp
Freezing case
(upper)
Freezing case
(lower)
Ice tray
Cannot be removed.
Two-layer soundproof mat
The soundproof mat consists of two layers.
Install the mat in the order shown.
No holes
Holes
Reduces the sound of ice dropping into the storage bin.
Do not discard.
Vegetable stand
33
8
DISASSEMBLY INSTRUCTIONS
MR-G50M-C
Plug out before work!!
Check the automatic ice-maker pressing ice making stop switch.
In assembling & disassembling parts seven kinds of screws and rivets are used. Do not mistake to use them.
4 12
Stainless steel
4 12 (Black)
With metal washer
4 16 (White)
With plastic washer
Specified screw
OPERATING PROCEDURE
1.
Elect cover Control board
(1) Remove 5 screws fixing the elect cover and the rivet on the upper rear side of the refrigerator. (See photo 1)
Control board
(2) Disconnect the connector to remove the control board.
Caution on assembly
Firmly connect the lead wires and the connector. Ensure the wires are not pinched.
Photo 1
Rivet
Rivet
PHOTOS
Rivet
Elect cover
5 fixing screws
2. Parts inside the refrigerator compartment: AUTOshelf
(1) Remove two-way flexishelf from the refrigerator compartment.
Photo 2
AUTO-shelf
Move the lever to the right, and slide the AUTO-shelf to the uppermost position. (See photo 2)
Push the catches (4 places) inward, and remove the AUTOshelf from the metal stoppers. Lift up and remove the AUTOshelf toward you. (See photo 3)
Remove the metal stoppers in front, back, left, and right sides of the unit.
Caution on assembly
First, install the metal stoppers to the unit. Then, place the
AUTO-shelf on top, and push the AUTO-shelf downward until it clicks into place (4 places). Refer to Photo 4 for the direction of the metal stopper installation.
Photo 3
AUTO-shelf
Lever
Two-way flexishelf
Catches
AUTO-shelf
Catches
Ceiling of side chilled compartment
Lever
Catches Catches
AUTO-shelf
Metal stopper
Catch
Photo 4
34
Metal stopper
OPERATING PROCEDURE
Removing the AUTO-shelf from the AUTO-shelf frame.
Remove the catches in the back (3 places), and lift up the
AUTO-shelf as shown in Photo 6. (See photo 5, 6)
The catches in front (4 places) will detach. Pull the AUTO-shelf toward you to remove.
Photo 5
PHOTOS
AUTO-shelf frame
AUTO-shelf
Photo 6
Catch
Catch
Catch
AUTO-shelf
AUTO-shelf frame
3.
Parts inside the refrigerator compartment: Vertical partition
Right rail of the slide compartment Left rail of the slide compartment Room light cover Control panel (Upper/
Lower), Duct R (Upper/ Lower)
(1) Remove the slide chilled case, AUTO-shelf and two-way flexishelf from the refrigerator compartment.
Photo 7
Vertical partition
Remove the small item case and the slide chilled case.
Pull out the ceiling by unhooking the front catches on both sides.
Remove the slide chilled case lid.
Remove the vertical partition.
Photo 8
Control panel
Right rail of the slide compartment
Small item case
(with free egg
shelf (S))
Ceiling of slide chilled compartment
Slide chilled case lid
Left rail of the slide compartment
Small item case
Slide chilled case
Vertical partition
Right rail of the slide compartment
(2) Slide the right rail out toward you. (See photo 7)
Left rail of the slide compartment
(3) Slide the left rail out toward you. (See photo 8)
Room light cover
Push up the lower catch, and pull the room light cover toward you.
Detach two upper catches to take out the cover.
(See photo 9)
Photo 9
Catches
Control panel
Room light
Room light cover
Catch
35
OPERATING PROCEDURE
Control panel Duct R
(4) Remove rivet , and pull out the mirror hinge on the lower left of the control panel to remove the connector. (See photo 10)
(5) Remove rivet (2 rivets) in the upper left and right side, screw
(1 screw) in the lower left side.
Detach catches (7 places).
(See photo 10)
Control panel assembly
(The assembly consists of the following: Control panel, refrigerator compartment thermistor, slide chilled compartment thermistor, room light socket, refrigerator compartment room light, and duct R).
Photo 10
Rivet
Screw
PHOTOS
Catch
Catch
Rivet
Mirror hinge
Control panel
Caution on assembly
To prevent poor contact of connectors, connect them properly.
Fix the control panel by inserting the lower catches (2 places) into the floor of refrigerator compartment.
Rivet
Catches
4.
Parts inside the versa compartment Ceiling of versa compartment
(1) Take out interior parts of versa compartment.
(2) Lift up and pull out the versa-compartment door.
Ceiling of versa compartment
(3) To detach the ceiling, remove rivet (3 rivets) and pull down the ceiling. (See photo 11)
Photo 11
Rivet
Rivet
Rivet
Ceiling of versa compartment
Caution on assembly
Be sure that all the parts are fitted securely in place.
5.
Parts inside the ice making compartment, versa compartment, vegetable compartment, and freezer compartment
Partition I/ S Partition I/ S/ V Cover (IM) Automatic
ice maker assembly Cover (lower) Partition V/ F
Connector cover (right/ left) Fan grille Defrost heater,
Drip tray, DEF thermistor
Photo 12
Screws
Rivet
Partition cover
(1) Remove interior parts out of ice making compartment, versa compartment, vegetable compartment, and freezer compartment.
(2) To detach them, pull out the doors of ice making compartment, versa compartment, vegetable compartment, and freezer compartment.
Partition I/ S
(3) Remove rivet (1 rivet), partition cover, and a connector.
Remove screw (2 screws) at the front side of refrigerator and four rollers to pull out the partition.
(See photo 12)
Caution on assembly
Push up the lead wires so that they will not rub partition I/ S.
Partition I/ S/ V
(4) Remove screw (2 screws) at the front of refrigerator.
Remove (1 screw each) at the right and left side of inner wall.
Then lift up the partition.
(See photo 13)
Cover (IM)
(5) Catches in order to detach the cover.
(See photo 14)
Automatic ice maker assembly
(6) Pressing a catch upward, and pull Automatic ice maker assembly to the right side. (See photo 14)
Photo 13
Photo 14
Rollers
Screw
Tank holder
Screws
Screws
Tank holder
Cover
(IM)
Partition
I/S
Rollers
Partition I/ S/ V
Screw
Catch
Automatic
Ice maker assembly
Catches
(Cover)
36
OPERATING PROCEDURE PHOTOS
Cover (upper)
(7) Remove rivet (1 rivet) to detach the cover (See photo 15)
Cover (lower)
(8) Remove rivet (1 rivet) to detach the cover (See photo 16)
Partition V/ F
(9) Remove screw (4 screws) on inner wall and screw (2 screws) at the front.
Detach three connectors and lift up the partition. (See photo
15)
Connector cover (right/ left)
(10) To detach connector cover, remove rivet (2 rivets each) and catches (2 places).
(See photo 16)
(11) Detach the connector.
Photo 15
Photo 16
Partition V/F
Cover (upper)
Rivet
Screws
Screws
Catch
Fan grille
Rivet
Fan grille
(12) To detach fan grille, remove screw (2 screws) on right and left side, rivet (1 rivet) on left side, and detach upper catches (3 places).
Fan grille consists of the following: motor dampers (for ice- making compartment/ refrigerator compartment, versa compartment), refrigerator fan motor, fan, thermal fuse, vegetable compartment heater 1, 4 thermistors.
(See photo 16)
Connector cover (left)
Rivet
Cover (lower)
Connector cover (right)
Evaporator
(13) Detach catch protruding from drip tray (See Figure 1) to remove evaporator.
Defrost heater, Drip tray
(14) Detach catch on drip tray (See Figure 2), and slide out defrost heater toward you. Remove heater roof and heater cover from defrost heater. Remove the aluminum tape, and then remove drip tray.
Figure 1
Catch
Rivet
Screws
Fan grille
(Fan grille consists of the following: motor dampers (for ice making compartment / refrigerator compartment, versa compartment), refrigerator fan motor, fan, thermal fuse, vegetable compartment heater 1, 4 thermistors).
Evaporator
Defrost thermistor (DEF thermistor)
(15) Cut the binder and disconnect the connector to remove the
DEF thermistor and the thermal fuse. (See photo 17)
Caution on assembly
Attach defrost heater in place and loosen the lead wires in order to prevent water from entering the glass tube.
Attach the drip tray securely to the lower parts.
Attach the DEF thermistor in place. (If they are attached out of place, thermal characteristics will go wrong.)
Attach the lead wires to the fixture.
Figure 2
Drip tray
Catch
Drip tray
Entering side
Entering pipe of evaporator
Black tube
30
Black marking on the unit entering pipe
* Brazed section
on the upper side
EVAP piping installation
Exit side
Exit pipe of evaporator
Gray tube
No marking on the unit exit pipe
* Brazed section
on the lower side
Photo 17
Defrost heater
Evaporator
DEF thermistor
Defrost heater
37
OPERATING PROCEDURE
Spacer (left), spacer (right)
Spacer
installation diagram
Spacer (left)
Evaporator
FIGURE
Spacer (right)
Side plate
Left side of evaporator
Row 1
Row 2
Left side of evaporator
Engage part 002 to the side plate of part 001, and slide it to the direction indicated by the arrows to secure it to the piping in the middle column at row 1 and 2.
Row 1
Row 2
Entering pipe
Row 3
Notch
Right side of evaporator
Slide part 003 to the direction indicated by the arrows.
Set the entering pipe into the notch, and secure it to the piping in the middle column at row 2 and 3.
Right side of evaporator
38
OPERATING PROCEDURE
6.
Parts inside the refrigerator compartment Left rail of the slide compartment Parts inside the ice making compart-
ment Ice making compartment door Tank holder
Door switch
(1) Remove the parts inside the refrigerator compartment.
(See procedure [2], [3])
(2) Remove the left rail of the slide compartment.
(See procedure [3])
(3) Remove the parts inside the ice making compartment.
(4) Remove the ice making compartment door.
Photo 18
Tank holder
(5) Remove a screw on the side of the refrigerator compartment.
(6) Loosen screw (3 screws) halfway on the side of the ice making compartment. Put a screwdriver on the head of each screw and top the bottom side of the holder softly to detach it.
(See photo 18)
(7) Lift up the tank holder from the refrigerator compartment to remove it.
Figure 3
Note:
Put the lead wires in place so that they do not get caught in water supply channel.
Put the tank holder in place so that the water does not leak from it.
Door switch
(8) Insert a minus screwdriver between switch and body to remove the door switch.
7. Operation panel
How to remove
(1) Slide the operation panel in the direction of the arrows, unit it stops. (See figure 4)
(2) Pull out the operation panel as shown in a figure 5.
(See figure 5)
Note:
Please pull it out carefully because it is still wired to the body.
Figure 4
Figure 5
(3) Take out the panel by detaching the connector of lead wires from the body.
(See figure 6)
Note:
If the horizontal slide is hard to remove with hands, put plate on the right edge of the panel (please put protective object such as tapes on the area of contact on the door panel and the operation panel), and gently tap it in the sliding direction.
(See figure 4)
Figure 6
PHOTOS
Screw
Door switch
Tank holder
Tank holder
Connector
39
OPERATING PROCEDURE
8.
Door closer
(1) Remove refrigerator compartment doors (right and left).
(2) Turn the doors upside down, and remove screws (1 screw each) of door stoppers for vegetable compartment door (right) and freezer compartment door (left). (See photo 19)
(3) Remove door closer. (See photo 20)
Note:
Refrigerator doors should be opened 90 degrees at the time
of installation or removal.
Photo 19
PHOTOS
Screw
Door stopper
Upside-down refrigerator compartment door
Photo 20
Refrigerant compartment door
Door closer
9.
Rotational heater board
(1) Remove 4 fixing screws to remove the rotational heater board.
(See photo 21)
(2) Remove a screw on the wiring cover and disconnect the connector in the cover. (See photo 21)
Photo 21
Screw
Wiring cover
Caution on assembly
When raising the rotational heater board, replace the rotational heater board as it was. if the refrigerator door is closed with the board raised, the rotational heater board may hit against the left door of refrigerator and be damaged.
Though heater preventing dewdrop may make rotational heater board hot, it does not affect food inside.
Refer to right figure when installing the rotational heater board.
(See figure 7)
Loosen the fixing screw and adjust a vertical (upper and lower) motion.
After assembling, make sure that the rotational heater board fits the guide properly and works properly.
Rotational heater board
Screws
Figure 7
Rotational heater board
Guide
3 2mm
Left door of refrigerator compartment
(4)mm
40
OPERATING PROCEDURE
10. Toe grille
Detach catch (2 places) and remove toe grille.
Caution on assembly
Remove PE tube (2 places, on right and left side) (See photo
22)
If PE tube is not removed, toe grille cannot be installed.
Tilt the toe grille to install, as shown in photo 23.
Catch (2 places) on the back of toe grille should come to the position indicated . (See photo 24)
Refer to the label on compressor cover (photo 23) for caution on assembly.
11. Compressor cover Drain pan Machine chamber
Photo 22
Photo 23
Castor
PHOTOS
Freezer compartment
PE tube
Tog grille
Castor
Compressor cover
(1) Remove 7 screws for compressor cover at the back of the refrigerator. (See photo 25)
Drain pan
(2) Remove screw (3 screws). (See photo 26)
Photo 24
Caution on assembly
Secure the screws in the following order: Right screw, Left screw, Center screw. (See photo 26)
Caution
Wash the drain pan with water in case it is dirty.
Machine chamber fan
(3) Disconnect connector.
(4) Remove screw (1 screw) securing bell mouth, and disconnect connector. Pull out bell mouth.
Condenser
(5) Remove screw (2 screws) and remove condenser. (See photo
27)
Caution
Arrange wiring as shown in photo 28 and photo 29.
Photo 28
Photo 25
Photo 26
Screws
Screw
Screw
Label
Catches
Screws
Compressor cover
Screw
Screw
Back of tog grille
Screw
Screw
Screw
Photo 29
41
Drain pan
Photo 27
Compressor Condenser
Machine chamber fan
Condenser
Screw
Screw
OPERATING PROCEDURE
Figure 8
Attach U washer as the figure shown below.
Piping connection of two-way valve
Exit
0.82
Two-way valve
W
Capillary tube
Dryer
W
W
W
Charge pipe
(High pressor side)
W
: This mark shows welded point.
Bell mouth
22.8
W
W
W
W
W
W
W
W
EFI100E
Charge pipe
(Low pressor side)
Compressor
Adjust piping and secure clearance of about 10 to 15 mm around pipes.
Make sure clearance is secured especially between the following parts.
Between charge pipe and compressor cover, bottom pan, compressor,
or discharge pipe.
Between suction pipe and compressor cover or capillary tube.
Between capillary tube and two-way valve or lead wires.
Machine chamber fan motor
42
Door adjustment
<Adjusting refrigerator compartment doors>
• Common elements
First, check the installation condition.
If the adjustment bolt is not in contact with the floor, lower the bolt, and adjust it so that the caster is slightly above the floor.
When the refrigerator is installed in the corner of the room, the bolt of the refrigerator may sink into the floor and cause the refrigerator to tilt. It is recommended to make adjustments by objects like boards beforehand.
When the refrigerator bolt is sunk into the floor, and it can be confirmed visually, prevent sinking by using objects like boards.
Note : The refrigerator weighs about 100kg, and is held by four bolts. How far each bolt sinks into the floor depends on
factors such as floor pillars. Change in balance due to position of stored food (such as large or small amount of food
stored in the door pockets) may also affect sinking.
<Adjusting ice making compartment and versa compartment doors>
Adjusting vertical space between doors
Adjusting doors horizontally
Too much space Not enough space
B
A
B
A
A>B (More space in outer side)
Or
A<B (More space in inner side)
Place spacer set under the outer roller of the tilted door
(ice making compartment door in the above illustration) to
Place spacer set under the inner roller of the tilted door
(ice making compartment door in the above illustration) to
Marking right 0.5 [09] right 1.0 [11]
LH
A>B (Too much space between the ice making compartment and versa compartment doors.)
Misaligned versa compartment door
Misaligned ice making compartment door
A<B (Small space between the ice making compartment and versa compartment doors.) Misaligned versa compartment door Misaligned ice making compartment door
Replace roller set of the right and left versa compartment
doors.
a To adjust about 0.5mm
replace with roller set C.
b To make large adjustment replace with roller set D.
Replace lower roller set of the ice making compartment door.
c To adjust about 0.5mm
replace with roller set A.
d To make large adjustment replace with roller set B.
RH
Marking right 0.5 [10] right 1.0 [12]
Replace roller set of the right and left versa compartment doors.
a To adjust about 0.5mm
replace with roller set A.
b To make large adjustment replace with roller set B.
Replace lower roller set of the ice making compartment door.
c To adjust about 0.5mm
replace with roller set C.
d To make large adjustment replace with roller set D.
Identifying roller sets (Marking)
Roller set A (0.5mm to the right)
Roller set B (0.5mm to the right)
Roller set C (0.5mm to the right)
Roller set D (0.5mm to the right)
LH
09
11
13
15
RH
10
12
14
16
Check points after adjustment
When adjustments such as hinge position have been made without food in the door pockets, confirm the door position again with food stored inside.
When the refrigerator is moved to make adjustments in the back bolts, floor may be damaged due to objects trapped in the caster. It is recommended to take preventive measures such as cleaning around the refrigerator and covering the floor with boards before moving the refrigerator.
After adjusting the refrigerator compartment doors, confirm auto closer operation.
43
HEAD OFFICE: TOKYO BLDG., 2-7-3,MARUNOUCHI,CHIYODA-KU, TOKYO100-8310,JAPAN
Copyright 2007 MITSUBISHI ELECTRIC ENGINEERING CO., LTD.
Distributed in Jul. 2007. No. OAH094 7
Made in Japan
New publication, effective Jul. 2007
Specifications subject to change without notice
Download
Advertisement
Key features
Auto-shelf for flexible storage
Vegetable compartment preserves freshness
Auto ice maker for convenient ice
Defrost system for easy maintenance
Temperature control system for precise cooling
Room light for visibility
Energy-saving ECO mode
Frequently asked questions
The total capacity is 495L.
Use the MODE switch to select the compartment you want to adjust and then use the SELECTION switch to set the desired temperature.
The dimensions are 1811 x 685 x 709mm.
The auto ice maker will automatically produce ice once you fill the water tank. There are options to turn off the ice maker or to use the ice maker compartment as a refrigerator compartment.
The refrigerators feature an automatic heater defrost system.