Mitsubishi Electric MR-LXR68EM-GBK-R Service Manual
पीडीएफ
दस्तावेज़
विज्ञापन
विज्ञापन
Changes for the Better HOME REFRIGERATORS SERVICE MANUAL Models 2018 NO. SM-RE-1822 MR-LXR68EM-GSL-R MR-LXR68EM-GBK-R CONTENTS 1 1. SPECIFICATIONS....................................................................................................................... 3 2. OUTLINES AND DIMENSIONS.................................................................................................. 4 3. WIRING DIAGRAM…………….............................................................................................. 6 4. REFRIGERANT CIRCUIT……………............................................................................................ 7 5. NAME OF PARTS...................................................................................................... 9 6. TROUBLE SHOOTING…………………………………………………………………………. 9 6.1 FUNCTION OF OPERATION PANEL…………………………………………………………… 22 6.2 FLOW CHART OF SELF-CHECK……………………………………………………… 25 6.3 BLOCK DIAGRAM OF PRINTED CIRCUIT BOARD…………………………………… 25 6.4 AUTO ICE-MAKER……………………………………………………………………………… 28 6.5 FLOW CHART OF TROUBLE CRITERION…………………………………….. 35 6.6 TROUBLE CRITERION OF MAIN PARTS…………………………………… 40 6.7 TEST POINT DIAGRAM OF MAIN CONTROL BOARD…………………. 41 7. DISASSEMBLY INSTRUCTIONS……………………………………………………. 46 8. PART LISTS………………………………………………………………………………… R……….Russia 1 SPECIFICATIONS 1-1 SPECIFICATIONS MR-LXR68EM-R Power supply Total capacity (AS Gross) Dimensions (HXWXD) Cabinet Food liner Cabinet Refrigerator door Insulation Vegetable door Freezer door Cooling system Freezer Refrigerator Evaporator Condenser Defrost system Drain Temperature control system Refrigerator room light L mm. Glass shelf ( R ) Slide chilled case up Slide chilled case low Water tank Free pocket ( S ) Free pocket ( L ) Egg case Accessories Bottle pocket Capsule door pocket Vegetable case Fruit case Freezing case (UP) Freezing case (LOW) Ice box sheet Weight Ice spoon Ice box Kick plate Unit Shipping kg kg 1 220 V 50Hz 630 (R : 333 V : 117 F : 180) 1798 x 900 x 735 Acrylic resin coated steel ABS resin Foamed cyclopenthane Foamed cyclopenthane Foamed cyclopenthane Foamed cyclopenthane Forced air convection 3 way air flow Fin and tube type Concealed type Automatic (Defrost heater ) Automatic (drainage) Automatic control LED Light Board 2 pcs. 1 pc. 1 pc. 1 pc. 2 pcs. 2 pcs. 1 pc. 2 pcs. 1 pc. 1 pc. 1 pc. 1 pc. 1 pc. 1 pc. 1 pc. 1 pc. 1 pc. 110 123 1-2 ELECTRICAL PARTS SPECIFICATION MR-LXR68EM-R Model Power supply Rated input Compressor Starting current Rated current o Winding resistance (A.T. 20 C) Model Motor protector Ambient temperature Time Current Capillary tube Dehydrant Molecular sieve Refrigerant R600a Defrosting timer Defrost finish Defrosting Thermal fuse control Defrost heater Deodorizing function of defrost heater Model Type Freezer Rate Voltage Input Power Revolution Model Machine Type Chamber Input Power Revolution Vegetable case heater Heater Chilled case heater Water pipe heater W A A o C Sec. A mm. g g o C C o W r.p.m Fan motor Temperature control Dial position LESS COLD COLD COLDER o C C o C o C o EEI91E13DWH 220 V, 50Hz 37 (1620 rpm) 6 (current limiter) 0.86 (1620 rpm) 16.72 Ω MM3-71CCY 25 16 MAX 17 ∅ 1.6 X ∅ 0.65 X 2350 9 94 Control board Thermistor 14 + 1.5 73 339 Ω (240V 170W) Not equipped 12537JE-13P-BU-F2 DC brushless motor 12 VDC 4.2 (12 VDC) 2300 (12 VDC) 4715JL04WS16G51 DC brushless 1.44 (12 VDC) 1450 (12 VDC) 6 6 0.9 W r.p.m W W W Thermistor F Thermistor R Thermistor C Freezer Refrigerator Chilled case ON OFF -0.4 -1.6 ON -12.9 -17.1 -20 - OFF -16.8 -20.8 -23.8 - ON 5.4 2.3 -0.2 - 2 OFF 4.8 1.6 -0.9 - 2 OUTLINES AND DIMENSIONS MR-LXR68EM-R Unit : mm Required Space For Installation 3 3 WIRING DIAGRAM (SKELETON WIRING DIAGRAM) PLUG MR-LXR68EM-R 4 MR-LXR68EM-R (ACTUAL WIRING DIAGRAM) 5 4 REFRIGERANT CIRCUIT MR-LXR68EM-R 6 5 NAMES OF PARTS MR-LXR68EM-R 7 8 6 TROUBLESHOOTING 6.1) FUNCTION OF OPERATION PANEL (1) Function of normal operation Touching will cause the operable icons to light up. To save power, all displays other than are usually turned off (it turns off if there is no operation for about 30 seconds). Home Icon Child safety lock When turning ON or OFF settings, touch one of these. Touch an icon to display its setting details. The operation panel employs the touch screen which is operated by touching the screen with your finger. - Icons and other displayed items except are not normally lit for saving energy. To check the setttings, touch to light up those icons and items. - The operation may not work properly in the follwing cases. * The operation panel or your finger is wet or dirty. * The operation panel is touched with a gloved finger or a finger with a bandage. * The operation panel is touched with a sharp-pointed instrument. - If the operation panel does not respond to touch on the screen, release your finger from the screen and touch it again. Touching the screen again without pause may result in false detection. Touching on the screen strongly does not enhance the detection sensitivity. - The response of operation panel depends on the ambient temperature and humidity, physical condition of the user, and operating conditions of the electric appliances around the refrigerator. * To initialize the settings, touch for 10 seconds. The settings will become as follows. - " S-COOL CHILL, RAPID COOL and ENERGY SAVING " will become canceled. - " Referigerator compartment and freezer compartment " will become set to " Middle ". 9 (2) Demonstration mode for shop display 1. Setting - Within 1 minute after power supply turns on, touch the , and simultaneously for 5 seconds with the door of the refrigerator compartment opened. * When the setting is complete, 2 short beeps sound is heard and is displayed. * Demonstration mode is not available when the temperature of freezer compartment is –7°C or lower. 2. Panel operation mode during demonstration mode During the demonstration mode, is continuously lit. Manual mode: By touching the icons, display on the operation panel changes as it is normally operated. Auto mode: Panel display automatically changes. ** When any icon is touched, the panel operation switches to the manual demo mode. When no icon is touched for 10 seconds after the operation panel turns off, it switches to the auto demo mode. 3. Release / Remove 1.Open the freezer compartment’s door during demonstration mode, and leave it open. Note : Follow the procedure above to release demonstration mode as it cannot be released by simply turning on/off the power supply. (3) Ice making test/Self-check 1. Setting (4) Temperature adjustment for slide chilled case (low) [ When supercool chiling is set ] 1.Outline The slide chilled case (low) in refrigerator compartment can be set to when it is set to supercool chilling. Otherwise, if the slide chilled case compartment was not cold, please set to 3) Touch in order to change the temperature setting of ) 10 . (5) Fine adjustment of temperature (6) Service Diagnostics Function 1) Out Line - The chart in next page shows the outline of service check function. - “Service diagnostics function entry” needs to be set in order to perform each check mode. - After the service check function entry,” Touch to select the serial number for the check mode to be performed. Press for 3 seconds to start the selected check mode. - blinks while service check function is performed. - When one of the check modes is in operation, the other check modes cannot be set. The check mode in operation needs to be cancelled before setting another check mode. 11 Note : * After one of the check modes starts, the mode continues operating even if the door gets closed. (Open the door when releasing the check mode.) * Refer to the following sections about the operation procedure and the display of each check mode. - In order to release “service diagnostics function entry,” follow the same procedure as that for setting operation during “service diagnostics function entry” or each check mode. Touch to light up the icons. Setting/releasing method 1. Enter the service check function. (Service diagnostics function entry) Door Display Blinking Operation Open the freezer compartment door. Touch and simutaneously for 3 seconds. Selecting method Door Display Any of the following : blinking Operation Blinking 2. Select the check mode. Open the freezer compartment door. Each touch of Touch . changes the blinking indicator(s) between Each combination of indicates the serial number for each check mode. * The service diagnostics function entry starts from the serial number1, blinking of No. 1 2 3 Mode Compressor rotational speed change mode 4 1 …The rotational speed of the compressor can be changed. The box fan(At machine room) can be switched on and off. Damper operation mode 2 …Each damper can be opened and closed. Freezer fan motor can be switched on and off. 5 6 7 3 8 4 Thermistor temperature check mode …The detected temperature of each thermistor can be checked. The serial numbers "4" can be selected, but do not set the mode to any of them. 5 Set temperature adjustment mode Selecting method Display …The set temperature and the energization rate in each compartment can be adjusted. The serial numbers from 6 to 8 can be selected, but do not set 6-8 the mode to any of them. Those modes are for factory use only. Door Operation Open the freezer compartment door. Touch for 3 seconds. Any of the following : lit Blinking 3. Set the check mode. The indicators of the serial number ( ) for the selected check mode stop blinking and remain lit. 12 2) Compressor rotational speed change mode 1. Setting • With the freezer compartment door open, touch until 2 short beeps sound. and simultaneously for 3 seconds will blinks. • With the freezer compartment door open, touch • With the freezer compartment door open, touch to select blinking for 3 seconds until 2 short beeps sound. The compressor rotational speed change mode has started. The mode continues operating even if the door is closed. Note : The compressor rotational speed change mode is not available during the demonstration mode, the thermistor temperature check mode, the temperature adjustment mode, or when the child lock is enabled. 2. Display during the compressor rotational speed change mode During compressor rotational speed change mode, blinks and is lit. 3. Display of rotational speed - The ones place and tens place of the compressor rotational speed are displayed separately. - One of the numbers (8, 4, 2, and 1) is assigned to each indicator of both tens place and ones place on the display. The sum of the numbers corresponding to the lit indicators is the compressor rotational speed. Blinking Maximum rotational speed of compressor, Level 9 or Level 10. Ones place of the compressor rotational speed Box Fan (At machine room) ON/OFF Tens place of the compressor rotational speed is lit e.g.) Compressor rotational speed 53 rps, Box Fan(At machine room) ON Blinking Box Fan (At machine room) ON Tens place "5"(=4+1) Ones place "3"(=2+1) is lit Tens place of the compressor rotational speed Display Corresponding numbers Ones place of the compressor rotational speed Display Corresponding numbers 8 8 4 4 2 2 1 1 13 4 Changing the rotational speed After setting this mode, the rotational speed of the compressor changes every time when is touched. The ones place and tens place of the rotational speed(rps) are displayed separately. (Basically the compressor starts operation at level 10, however, it may be different depending on models, or as a result of specification change.) <Change of rotational speed> Normal Level 0 Level 2 Level 1 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 Level 9 Level 10 High speed Low speed * Rotational speed can be changed only when the compressor is in operation. While the compressor stops, rotational speed is not displayed and the touching operation of is disabled. When the compressor stops, unplug the power cord, and wait for several minutes, then plug it again. * Operation sound may increase in the process of changing rotational speed, but that is not mulfunction. Check the sound level when rotational speed is stabilized. 5 Switching ON/OFF the box fan motor(At machine room) During this mode, touching in order to turns on/off the box fan motor(At machine room). The ON/OFF state is represented by Box fan ON Lit OFF Not lit 6 Switching the maximum rotational speed of the compressor between Level 9 and Level 10 During this mode, the maximum rotational speed of the compressor can be switched between Level 9 and Level 10 by touching for 3 seconds. ( The maximum rotational speed of the compressor is represented by ) Maximum rotational speed of compressor Display of Level 9 Lit Level 10 Not lit • While the maximum rotational speed of the compressor is set to Level 9, the rotational speed cannot be changed to Level 10 by following the method described in “ 4 Changing the rotational speed”. • When high load is applied to the refrigerator such as in summer, setting the maximum rotational speed to Level 9 may not Normal obtain adequate cooling. Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 Level 9 • The maximum rotational speed of the compressor that was set to Level 9 will remain the same even after this mode is released. The maximum rotational speed of the compressor will be memorized in the control board. So, if the control board is replaced, the set maximum rotational speed will be reset to Level 10. 7 Release • With the freezer compartment door open, press and simultaneously for 3 seconds until 2 short beeps sound. The operation panel returns to the normal temperature display. • The function is automatically released in 1 hour. • Although unplugging and plugging the power cord can release this function, it is recommended to follow the procedure above for protection of the compressor. * The set maximum rotational speed of the compressor will remain the same even after the power is turned off. 14 3) Damper Operation Mode 1 Setting • With the freezer compartment door open, touch and simultaneously for 3 seconds until 2 short beeps sound. will blinks. • With the freezer compartment door open, touch to select blinking • With the freezer compartment door open, touch for 3 seconds until 2 short beeps sound. The damper operation mode has started. This mode continues operating even if the door gets closed. Note : The damper operation mode is not available during the demonstration mode, the compressor rotational speed change mode, the thermistor temperature check mode, the temperature adjustment mode, or when the child lock is enabled. 2 Display during the damper operation mode During damper operation mode, blinks and is lit 3 Control state display of each damper Blinking c) Freezer fan motor ON/OFF d) Display during the damper operation “Blinking” is lit b)State of damper a) Damper serial number : present state : next state a) Damper serial number - Each serial number is assigned to each compartment (thermistor), which is used in thermistor temperature mode and set temperature adjustment mode besides damper operation mode. - The values (8, 4, 2, and 1) are assigned to each indicator. The sum of the values corresponding to the lit indicators is the damper serial number. Display Serial Number Assigned compartment Damper operation mode 1 Refrigerator compartment O 2 Chilled O 3 Freezer compartment X Corresponding values 4 Defrosting - 8 5 Ice tray - 4 6 Outside air - 2 O / X / - : SW operation is effective / ineffective / Cannot select 1 Chilled : For slide chilled case (low) b) State of damper represents the current state and represents the next state of damper operation. - Both buttons indicate that the damper is open when they are lit, and they indicate that the damper is closed when they are not lit. Present Next 15 4 Opening and closing dampers 3 : freezer) (2) To open the damper, light up by touching . To close the damper, turn off by touching again. **Damper operation indicators on the left represents the current state and on the right represents the next state of the damper operation. - Both buttons indicate that the damper is open when they are lit, and they indicate that the damper is closed when they are not lit. - When the selected damper is in operation, the indicator for the present state brinks. - When any damper including those which are not selected is in operation, blinks. <Present and next states of the damper of the selected compartment> Blinking <The damper of any compartments is in operation> e.g.) To open the damper of the refrigerator compartment, which is currently closed, select the items shown below and touch Blinking for 3 seconds c) Freezer fan motor Lit : ON is lit b)State of damper a) Damper serial number "1" : refrigerator compartment present : next : 5 Switching ON/OFF the freezer fan motor During this mode, touching in order to turns on/off the freezer fan motor. The ON/OFF state of the freezer fan motor is represented by . display Freezer fan motor Lit ON Not Lit OFF 6 Release and simultaneously for 3 seconds • With the freezer compartment door open, touch until 2 short beeps sound. The operation panel returns to the normal temperature display. • The function is automatically released in 1 hour. • Although unplugging and plugging the power cord can release this function, it is recommended to follow the procedure above for protection of the compressor. 16 (Not lit) (Lit) 4) Thermistor temperature check mode 1 Setting • With the freezer compartment door open, touch and simultaneously for 3 seconds until 2 short beeps sound. will blinks. • With the freezer compartment door open, touch to select the blinking • With the freezer compartment door open, touch for 3 seconds until 2 short beeps sound. The thermistor temperature check mode has started. This mode continues even if the door gets closed. * The thermistor temperature check mode is not available during the demonstration mode, the compressor rotational speed change mode, damper operation mode, the set temperature adjustment mode, or when the child lock is enabled. 2. Display during the thermistor temperature check mode During the thermistor temperature check mode, blinks and are lit. 3. Displaying the thermistor temperature The kind and temperature of thermistor are displayed on the operation panel. *The outside air temperature detected by thermistor may be a little different from the actual one due to the influence of the temperature in the refrigerator. Blinking d) Plus and minus sign(±) of the thermistor temperature b) Tens place of the thermistor temperature is lit a) Thermistor serial number c) Ones place of the thermistor temperature a) Thermistor serial number - Each serial number is assigned to each compartment (thermistor), which is used in thermistor temperature mode and set temperature adjustment mode besides thermistor operation mode. - The values (8, 4, 2, and 1) are assigned to each indicator. The sum of the values corresponding to the lit indicators is the thermistor serial number. Display Corresponding values 8 Serial Number 1 Assigned compartment Refrigerator compartment 4 2 Chilled(Slide chilled case (low)) 2 3 Freezer compartment 1 4 Defrosting 5 Ice tray 6 Outside air b) Tens place of the thermistor temperature - Display of corresponds to the values 8, 4, 2 and 1 respectively. The sum of the values corresponding to the lit indicators is the tens place of thermistor temperature. Display Corresponding values 8 4 2 1 17 c) Ones place of the thermistor temperature - Display of corresponds to the values 8, 4, 2 and 1 respectively. The sum of the values corresponding to the lit indicators is the ones place of thermistor temperature. Display Corresponding values 8 4 2 1 d) Plus and minus sign(±) of the thermistor temperature - Plus and minus sign(±) of the thermistor temperature are represented by Display Thermistor temperature signs Lit Not lit + e.g.) The freezer compartment thermistor reads –25ºC. d) sign " - " Blinking b) Tens place : "2" is lit a) Thermistor serial number "3"(=2+1) : c) Ones place : "5"(=4+1) 4. Changing the thermistor on display - While thermistor temperature is displayed, touch . Each touch of changes the thermistor type along with a short beep. Each thermistor is displayed using the serial numbers described in a) in numeric order repeatedly (1: refrigerator compartment ~ 6 : Outside air). 5. Release • With the freezer compartment door open, touch and simultaneously for 3 seconds until 2 short beeps sound. The operation panel returns to the normal temperature display. • The function is automatically released in 1 hour. • Although unplugging and plugging the power cord can release this function, it is recommended to follow the procedure above for protection of the compressor. 18 5) Setting adjustment mode The temperature of each compartment and the energization rate of the heaters can be adjusted by touching the buttons on the operation panel. There are two modes. In the “setting adjustment mode”, the setting temperature of the compartment is adjustable. In the “heater energization rate adjustment mode”, you can adjust the energization rate of the water pipe heater and the ice-maker heater. Start the setting adjustment mode first to operate these modes. 1. Setting • With the freezer compartment door open, touch and simultaneously for 3 seconds until 2 short beeps sound. will blinks. • With the freezer compartment door open, touch to select the blinking • With the freezer compartment door open, touch for 3 seconds until 2 short beeps sound. The set temperature adjustment mode has started. This mode continues operating even if the door gets closed. 2. Display during the set temperature adjustment mode During set temperature adjustment mode, blinks and are lit. 3. Switching the mode. • Select the mode to adjust with Each touch of switches the mode between “setting adjustment mode” and “heater energization rate adjustment mode” along with a short beep. Display Setting adjustment mode Setting adjustment mode Adjust the temperature of each compartment Not lit Adjusts the heater energization rate of the water pipe heater and the ice-maker heater Heater energization rate adjustment mode Lit 4. Setting adjustment mode b) Display set temperature b) Display adjustment level " - " signs adjustment level Blinking (1) Display a) Compartment serial number is lit [ Mode display ] (Not lit) : Setting adjustment mode a) Compartment serial number Each serial number is assigned to each compartment that will be used in the set temperature adjustment mode besides damper operation mode and thermistor temperature check mode. The values (8, 4, 2, and 1) are assigned to each indicator. The sum of the values corresponding to the lit indicators is the compartment serial number. Display Corresponding values 8 Serial Number 1 Assigned compartment Refrigerator compartment 4 2 Chilled(Slide chilled case (low)) 2 3 Freezer compartment 1 b) Set temperature adjustment level 3 indicators of , (2) Adjusting the set temperature 1. Select the compartment with and display the adjustment level of the setting temperature. . Each touch of changes the compartment of which set temperature will be adjusted along with a short beep. Each compartment will be displayed using the serial numbers (1: Refrigerator compartment ~ 3: Freezer compartment) in numeric order repeatedly. 19 2. Select the adjustment level of the set temperature by touching . Each touch of changes the adjustment level of the set temperature along with a short beep. There are 5 adjustment levels of set temperature, and the selected level is displayed. Adjustment level Temperature adjustment display +2 +1 ±0 -1 -2 Change of the set temperature About +2 ºC About +1 ºC No change About −1 ºC About −2 ºC * The changed adjustment levels are stored on the control board. If the control board is replaced, the updated information will be lost. 5. Heater energization rate adjustment mode (1) Display Blinking a) Heater serial number is lit [ Mode display ] (Lit) : Heater energization rate adjustment mode b) Heater energization rate adjustment Performed/Not Performed a) Heater serial number The values 2, and 1 are assigned to each indicator. The sum of the values corresponding to the lit indicators is the heater serial number. Serial Number Assigned heater Display 1 Water pipe heater 2 Ice-maker heater b) Heater energization rate adjustment performed / not performed - Heater energization rate adjustment is performed or not performed are represented by Display : Heater energization rate adjustment Not lit Not performed Lit Performed (2) Adjusting the heater energization rate 1. Select the heater to adjust the heater energization rate with Each touch of makes a short beep, then changes the heaters to alter the energization rate thereof. The indicators will be displayed in numerical order according to the compartment serial number as shown in a) and switched alternately between 1. water pipe heater and 2. ice-maker heater. 2. Select to perform or not to perform the heater energization rate adjustment with . Each touch of makes a short beep, and changes to perform it or not. Display : Heater energization rate adjustment Not lit Not performed Lit Performed * When selecting to perform the heater energization rate adjustment, the heater energization rate is controlled to be higher. *The selected state for “performed” or “not performed” is memorized in the control board. If the control board is replaced, the memory regarding the adjustment will be lost. 6. Release • With the freezer compartment door open, touch and simultaneously for 3 seconds until 2 short beeps sound. The operation panel returns to the normal temperature display. • The function is automatically released in 1 hour. • Although unplugging and plugging the power cord can release this function, it is recommended to follow the procedure above for protection of the compressor. 20 Door Alarm System : Door alarm has been installed so that one will not forget to close the door. • The alarm beeps in the following cases: 1. Any of the doors is left open. 2. The freezer fan motor or the box fan motor(At machine room) has a failure. Alarm sound pattern 2. The freezer fan motor or the box fan motor(At machine room) has a failure 1. Any of the doors is left open. • The alarm alerts that the door is open when any of the compartment doors is left opened for 1 minute or more. • The alarm stops alerting as soon as the door is closed. • When the alarm does not stop even though all the doors are closed, the door switch may be abnormal. To Stop the Alarm (Continuous Short Beeps) The alarm can be temporarily stopped in the time before the refrigerator is repaired. Press for at least 5 seconds. * If performing the above operation does not turn off the alarm, or the alarm periodically sounds, check peripheral machinery as well. (Note: If the test is conducted with water in the ice tray, water may fall into the ice storage box because the tray turns over in the ice making operation.) * The indicator of the compartment on the operation panel blinks along to the alarm sound. 2. The alarm alert when a trouble is found in the freezer fan motor or in the box fan motor(At machine room). The alarm alert every time the door is closed until normal operation is obtained. (Check the error code by following the steps in Self-check and error display method and operation on next page.) Interior LED : • When the door of the refrigerator compartment is opened, the interior LED in the refrigerator compartment turns on. • While beeping continues due to the door that is left open for 4 or more minutes, the interior LED blinks twice per minute, which reminds the user to close the door. • If the interior LED continues to light for 60 minutes or more, the overheating protection is activated, which turns off the interior LED. • After that, closing the door releases the overheating protection function. The interior LED will turn on again when the door is opened next time. 21 6.2 ) FLOW CHART OF SELF-CHECK (1) Troubleshooting with self-check This refrigerator has self-check feature to clarify and indicate where & what the trouble is.You can perform operation checks and identify malfunction of electric or electronic parts.Error history is recorded and can be displayed by the refrigerator. A Self - check Operate the ice-making test. (Current displayed error: Refer to 1 in the table below.) The display of ice making compartment setting will blink during the test. During the ice-making test mode, visually check the operation of the ice-maker gear box and the water pump in refrigerator. No Is error displayed? Yes B Locate the trouble according to error display. (see 6.2 ( 3 )) Self-check cannot detect abnormalities in the following parts.(Please see the detail in remark 1) Remark 1. Self-check cannot detect abnormalities in the following parts. - Door SW R, Reed SW F NG - Heater NG (Vegetable compartment heater, etc.) - Motor Damper NG - Water supply pump motor NG Remark 2. If any abnormality is found when plugging the power cord, compressor and freezer fan motor stop for 10 minutes. Remark 3. The alarm beeps when some abnormalities (motorlocked) have occurred at the freezer fan motor or box fan motor(At machine room). The alarm beeps every time the door is closed until normal operation is obtained. Remark 4. If any abnormality occurs in compressor's inverter circuit, the compressor and the freezer fan motor stop for 10 minutes.(Not only when plugging the power cord.) Unplug the power cord from outlet. Repair /replace defective part(s) according to error display. Self - Check C Plug the power cord into outlet. (Current displayed error: Refer to 2 in the table below.) Yes * Wait 10 minutes before plugging the cord once it's unplugged. (If the cord is plugged in within 10 minutes, error may be displayed.) Is error displayed? No Self - Check is finished. * Self-check and error display method and operation Self-check (current displayed error) Items Operation method Display or self-check operation Display period Others 1 Ice making test operation. Touch for 5 seconds (2 beeps sound.) 1.Conduct the automatic ice making For 10 minutes test.(All the after setting. indicators blink.) 2.When trouble is found, all error codes are displayed. 3.When error is not found, nothing is displayed. Self-check is not available during the compressor rotational speed change mode, the thermistor temperature check mode, the damper operation mode, the demonstration mode, or when the child lock is enabled. 2 Power input * All item except (*6) listed up on the table at 6.2 (3) will be checked Plug the power cord into outlet. 1.When trouble is found, all troubles except For 10 minutes E50 - E55 are displayed. after power is 2.When an error is not found , nothing is supplied. displayed. Self-check is not available during demonstration mode. * Release of self-check display mode Self-check finishes automatically. The self check display is automatically released 10 minutes later. 22 (2) Timing in self-check * Trouble of Defrost heater : Self-check is conducted after defrosting. (Make sure to check the display before unplugging the power cord because it is automatically reset once the power cord is unplugged.) * Trouble of Ice maker : Touch for 5 seconds to operate the automatic ice maker. All the and indicators blink when operation is being checked during the test operation. * Trouble of Fan motor : Open the door and then close it. When any abnormality is found in fan motor, the alarm sounds every time the door is closed. * Trouble of Inverter : Check the error when the compressor starts up or is operating. * Trouble of Thermistor : Self-check is continuously working (3) Error display and trouble locating 1.Display Detail After conducting the self-check referring to 6.2(1), flashes repetitively and the error code is displayed. The tens place and ones place of the error code is displayed separately. When two or more errors occur, they are displayed alternately. The error of which code has smaller number has priority to be displayed first. There are 0.5 seconds intervals between the error codes. b) Ones place of the error code Flashing a) Tens place of the error code e.g.) In case the errors of refrigerator thermistor (E13) and ice maker gear box (E33) are occuring simultaneously. * For 2 minutes in self-check, a high-tone sound is heard due to the operation check of damper. (2) Check point and corrective measures Display Testing Error code Display Tens place Ones place Trouble FREEZER E 02 (*4) Communication error of operation panel The following communication errors occur between control board and operation P.C. board: • They transmit and receivedata that is unrelated to the settings. • They cannot transmit and receive data for about 10 seconds. Communication error of inverter A commutation error occurs between refrigerator control circuit and inverter control circuit in control board. (They do not transmit and receive data for 10 seconds.) Trouble of model judgement The model of control board is different from that of operation P.C. board. OFF MODE E 03 OFF MODE Self-check Check point Corrective measures Control Ice maker is under-testing E 01 Error display Detecting method (*1) FREEZER When there is a short or open circuit in the ice making tray thermistor. MAKE ICE Trouble of ice-making tray thermistor There is a short or open circuit in the freezer compartment thermistor. MAKE ICE Trouble of freezer compartment thermistor Trouble of defrost thermistor There is a short or open circuit in the defrost thermistor. Trouble of refrigerator thermistor There is a short or open circuit in the refrigerator compartment thermistor. E 10 E 11 FREEZER E 12 MAKE ICE OFF MODE E 13 MAKE ICE OFF MODE FREEZER 23 1. Connector CN5D, CN9S on control board 6-pin wire to wire connector (hinge) 6-pin connector on operation P.C. board. Repair the contact failure. 2. Trouble of control board or operation P.C. board Replace. Replace the control board. 1. Check the model name of control board. Replace. 2. Check the operation P.C. board. Replace. 1. Connector CN9S on control board, 6-pin wire to wire connector Repair the contact failure. 2. Check the resistance of thermistor. Replace. 1. Connector CN9S on control board, 2-pin wire to wire connector Repair the contact failure. 2. Check the resistance of thermistor. Replace. 1. Connector CN9S on control board, 2-pin wire to wire connector Repair the contact failure. 2. Check the resistance of thermistor. Replace. 1. Connector CN9S on control board, 6-pin wire to wire connector Repair the contact failure. 2. Check the resistance of thermistor. Replace. The same operation as that before the communication error has occurred is continued. Compressor turns OFF. The operation continues. The error code is displayed. When the freezer compartment door has been closed for 3 hours and when freezer compartment thermistor is -10ºC or less, ice-detecting operation starts. After the compressor turns OFF for 10 minutes, it turns ON for 30 minutes and OFF for 20 minutes repeatedly. The defrost heater is disabled. • The compressor is ON, the damper of the refrigerator compartment is open. • The compressor is OFF, the damper of the refrigerator compartment is close. Display Error code Display Tens place Ones place Trouble Detecting method REFRIGERATOR Trouble of chilled thermistor E 14 ON MODE Trouble of outside air thermistor MAKE ICE Trouble of defrost heater(*6) E 30 ENERGY SAVING MAKE ICE FREEZER MAKE ICE OFF MODE E 33 Self-check Error display ENERGY SAVING Repair the contact failure. 2. Check the resistance of thermistor. Replace. • When the motor damper for refrigerator compartment is open, the motor damper for chilled compartment(Slide chilled case(low)) is open. • When the motor damper for refrigerator compartment is closed, the motor damper for chilled compartment(Slide chilled case(low)) is closed. Replace the operation P.C. board. The control under the assumption that the outside temperature is 25°C is performed There is a short or open circuit in the outside air thermistor. 1. Connector CN3A, CN4A on control board, Defrost heater-2, Repair the 1-pin wire to wire connector, Thermal fuse 2-pin wire to wire contact failure. connector Defrosting is not finished in 2 hours. MAKE ICE OFF MODE FREEZER RAPID COOL E 50 MAKE ICE RAPID COOL E 51 MAKE ICE FREEZER RAPID COOL E 52 MAKE ICE OFF MODE RAPID COOL E 53 MAKE ICE OFF MODE RAPID COOL FREEZER REFRIGERATOR E 55 MAKE ICE FREEZER RAPID COOL REFRIGERATOR OFF MODE RAPID COOL REFRIGERATOR E 57 MAKE ICE OFF MODE Trouble of ice maker gear box • The motor does not rotate even though power is on. • The waveform, which indicates the rotation times of motor, cannot be detected. FREEZER The gear box operation is not finished in 30 seconds. Trouble of inverter circuit (*5) • There is any trouble in the circuit which detects current of compressor. Trouble of bus-bar voltage (*5) • The range of bus-bar voltage is not approx. 74 ~ 360 V DC. Trouble of inverter software reset function (*5) • The inverter driving software malfunctions. Trouble of startup, synchronization or overcurrent detection (*5) • There is no current at compressor startup. • The phase current exceeds 4.4 A at compressor startup. • The phase current exceeds 2.4 A during compressor operation. • A current of 5.6 A or more runs into the busbar of control board. Trouble of control board (EEPROM related trouble) (*5) EEPROM (IC11M) accumulates data necessary for control. • The data are not input accurately. • The microcomputer cannot read the data. Defective wiring connecting or trouble of control board E 56 MAKE ICE Trouble of freezer fan motor • The motor does not rotate even though Trouble of box power is on. fan motor • The waveform, which indicates the rotation (At machine room) times of motor, cannot be detected. E 32 ENERGY SAVING 1. Connector CN9S on control board, 2-pin wire to wire connector 2. Check the resistance of defrost heater-2. Replace. 3. Check the continuity of thermal fuse. Replace. 1. Connector CN5D on control board, freezer fan motor 4-pin wire to wire connector Repair the contact failure. 2. Check freezer fan motor operation. Replace. 1. Connector CN5D on control board, 4-pin wire to wire connector Repair the contact failure. 2. Check box fan motor operation. Replace. 1. Connector CN5D on control board, ice gear box 6-pin wire to wire connector. Repair the contact failure. 2. Ice gear box is frozen or has a sign of frost. Replace. 3. Check the trouble of the ice gear box in the ice making test operation. Replace. MAKE ICE E 31 ENERGY SAVING Corrective measures There is a short or open circuit in the refrigerator compartment thermistor. MAKE ICE E 18 Check point The errors E50 to E53 keep occurring over one and a half hour. (The situation, which compressor cannot be operated, continues.) The overcurrent error is detected before starting Inverter drive the compressor (Failure of the IC in the inverter module abnormality drive module). Control The defrost heater is stopped and if the next defrosting finishes in 2 hours, the error code will disappear. • 3 minutes later, the freezer fan motor is reactivated to be checked. • Until the fan motor operates correctly, the alarm sounds every time the door is closed. • 3 minutes later, the box fan motor is reactivated to be checked. • Until the fan motor operates correctly, the alarm sounds every time the door is closed. 100 minutes later, the gear box is reactivated to be checked again. Replace the control board. The compressor is stopped and reactivated 10 minutes later. Refer to “Compressor does not operate” in itemp topic no. 6.5 Replace the control board. Refer to “Compressor does not operate” on item topic no. 6.5 Replace the control board. If abnormality occurs when power is turned on, the compressor is stopped for 10 minutes. When abnormality occurs during normal operation, the compressor keeps operating. • The error display starts after the error is determined as E56. • The error display continues until defrosting starts or cooling operation gets back to normal. (The error display does not disappear by unplugging and plugging the power cord *6) • An attempt to restart the compressor is repeated every 3 minutes. An attempt to restart the compressor is repeated every 3 minutes. *1: All the " " and " " indicators blink after button operation for ice making test operation or during ice making test operation. *2: This operation is called the recovery operation: If the damper has not operated ever once during the compressor operation, make the damper operate when the compressor stops. *3: When the resistance is , the circuit is deemed open-circuited. When the resistance is 0 , the circuit is deemed short-circuited. *4: Once E01 is detected, other errors would be ignored and not displayed on the panel. *5: The error codes E50 to E55 are not displayed even if those abnormalities occur when power is turned on. Therefore, be sure to perform ice making test operation in order to check if any abnormality indicated by these error codes occurs. (See item topic 6.2) *6 : If those errors still continue for 1 minute after the restart, E56 will be displayed again. 24 6.3) BLOCK DIAGRAM OF PRINTED CIRCUIT BOARD For 340 V DC system - Compressor For 12V DC system - Freezer fan motor - Box Fan (At machine room) - Motor damper for chilled compartment and refrigerator compartment* - Ice maker gear box - Interior LED - LED light(Vitamin up) for vegetable compartment For 240 V AC system - Defrost heater - Water pipe heater - Vegetable compartment heater - Rotating partition heater - Chilled heater* - Ice maker heater For 5 V DC system - Freezer compartment thermistor - Refrigerator compartment thermistor - Defrost thermistor - Door switch (for refrigerator compartment) - Door switch (for freezer compartment) - Chilled thermistor* - Water supply pump motor - Ice maker gear box - Ice maker thermistor - Position-specifying switch ice maker gear box Remark : Parts that indicated at the end by " * " are used for adjust temp in the supercool chilling mode. 6.4) AUTO ICE-MAKER Ice maker thermistor watches and controls the ice making operation Ice is stocked in the ice storage box. Ice making capacity is about 100 - 120 cubes a day. Stock capacity of ice cubes is about 80 cubes. 2 pin connector Water supply pipe heater Ice maker heater 2 pin connector Ice maker gear box 6 pin connector REFCON ASSY Ice maker thermistor F-thermistor 2 pin connector F-room reed switch R-room door switch 3 pin connector (R-room section) R-room door switch 3 pin connector (R-room section) 4 pin connector 25 Water supply pump motor (3) Operation by ice making test Touch 5 seconds for The sensor lever detects the amount of ice. The ice tray is turned over and return. The water pump motor operates. The sensor lever once comes down to detection point then returns to the original position. The ice tray turns over once to drop the ice, then returns to the original position. Open the water tank cover and confirm* check the water level decrease. This ice tray was design for make ice 10 cubes per 1 time. (The ability for make ice that was not reach 10 cubes per 1 time can be possible.) Completion When error code still occur, please do inspection check for the ice-maker gear box, ice-maker termistor.(Referring to 6.2(3) *Confirm at here (Lower left view of refrigerator compartment) [ Check point of automatic ice maker operation. ] Never touch the automatic ice maker while it is operating. During the operation, do not insert a hand into the automatic ice maker. (4) Maintenance for water supply tank, purification filter, water supply pump and water supply pipe. Follow the procedures below when disassembling, cleaning, and assembling the pump and the pipe. Explain to customers that periodic cleaning is required. (The instructions for cleaning are described in the instruction book.) The inside of the pump can be cleaned after disassembling the pump in the water tank. The inside of the pipe can be cleaned after disassembling the water supply pipe in the tank holder. Please periodically clean to prevent the occurrence of water scale, mold, etc. Please remove water when not making ice. 26 (5) Troubleshooting for automatic ice maker - There is a possibility of a failure on the ice making gear box, deficiency in cooling performance, or detection of full ice level in the ice storage box. Water or ice exists in the ice tray. The ice does not come out from the tray. 1. Check inside of the ice storage box. - Ice cubes are not stored flatly and the amount is detected as full. - Something like food was locate inside the ice storage box. - Found open or short circuit - Not enough -> Check and correct the problem. Trouble with ice making. Water or ice exists in the ice tray. No waterdrops in water saucer Water in water saucer 2. Check resistance of circuit of ice-maker thermistor -> Replace Ice-maker thermistor 3. Check whether the temperature of the freezer -> Poor cooling compartment is cool enough. Extra time is required to make ice in summer or when the door is opened or closed frequently. 4. Detection lever was operate? -> Check ice-maker heater - Water supply path may have a failure, the ice tray may have a crack or not be set in place. 5. Check the water pipe for dirt and foreign - Clogging -> Clean the water pipe. objects. - Freezing (For freezing, check -> Deice. installation & measure the -> Check the connection of resistance of water pipe heater water pipe heater and installation position of sealing tape of water pipe 6. Check the installation condition of ice tray. - Crack -> Replace auto ice-maker. - Not be set in place -> Re-correct the installation. 7. Disassemble the water pump and check the - Dirt or clogged by -> Repair and explain to end-user inside of the pipe. foreign objects for proper usage. 8. Tank pipe is clogged, has a hole, or is not - Clogging, disconnecting -> Clean/Reinstall it properly. properlly installed. - Hole or crack -> Replace the tank pipe. 9. Check the coil resistance of the water supply - Open or short circuit. -> Replace water supply pump motor. pump motor. 10. Check if there are any dirt or foreign objects - Crack or deformation -> Replace the water tank. which are difficult to remove in the water tank. Also, check if there is any crackor deformation on the tank. - Clogging, disconnecting -> Clean/Reinstall it properly. Water in 11. Check the water supply pipe for dirt and foreign the objects. Also, check the water supply pipe position - Hole or crack -> Replace the water supply pipe. tank holder and connection. - Water filling period is longer than -> Replace the control board. Chained 12. Perform the ice making test and check the 9 seconds. ice, water operation of the water supply pump. leaking from 13. Water spill at the installation of water tank or too much water over the full water level may cause formation of chained ice. ice server 14. Check the coil resistance of the water supply pump motor. - Open or short circuit. -> Replace water supply pump motor. 27 6.5) FLOWCHART OF TROUBLE CRITERION Is the temperature of refrigerator compartment, set to ? No No cooling, poor cooling Is the temperature of refrigerator compartment, set to ? Set the temperature to Only food around the air outlet gets frozen. No Set the temperature to Yes Yes Yes Keep the food away from air outlet. Open the refrigerator compartment door and press the both two side of door switch(See *1) to check that cold air blows from the outlet. No No Proceed to " [6] The freezer fan motor does not work " Yes After ice making test operation, does the motor damper baffle for the chilled / refrigerator compartment, in the bottom of the refrigerator compartment open and close? (Wait 1 minute for selfcheck).(See in 6.2(1) for the table of " Self check method and its operation " ; Item no.1(Ice making test operation.)) The baffle does not operate Replace the motor damper for the chilled / refrigerator compartment. Yes Clean up the area that found frost forming. Normal Does the motor damper have a sign of frost forming? No Check the refrigerator compartment thermistor. Dip the refrigerator compartment thermistor into ice water (0°C), and disconnect the 6-pin connector leading from the thermistor attachment, and measure the resistance between the pin no. 5 (white) and 6 (white) terminals. • Resistance at 0°C : approx. 6-7 kΩ Resistance value abnormal Replace refrigerator compartment thermistor. Press the both two side of door switch *1 The set temperature can be adjusted on the operation panel -> Refer to 6.1 [ (6)Setting adjustment mode] R-room LED light board LED light board 4 pin connector LED light board LED light board 6 pin connector Refrigerator compartment thermistor 4 pin connector REFCON ASSY [1] Refrigerator compartment, Slide chilled compartment Excessive cooling Motor damper for chilled / refrigerator 28 Yes Is set ? Is it setting to ? Yes No cooling, poor cooling Do setting to Is set to or No Only food around the air outlet gets frozen. Yes Yes ? Do setting to or No No Open the refrigerator compartment door and press the both two side of door switch(See *1) to check that cold air blows from the outlet. Keep the food away from air outlet. No No Proceed to " [6] The freezer fan motor does not work " Yes Does the motor damper baffle for the chilled / refrigerator compartment, in the bottom of the refrigerator compartment open and close? (Wait 1 minute for self-check).(See in 6.2(1) for the table of " Self check method and its operation " ; Item no.1(Ice making test operation.)) The baffle does not operate Is connector CN5D on the control board connected properly? Connect the connector properly. No Yes No Disconnect CN5D and measure the resistances between pin no. 2 and 4, and between pin no. 6 and 8 . Check that the winding of the motor damper for chilled / refrigerator compartment has a resistance of approx. 415Ω . 0 Ω or ∞Ω Is the 6-pin connector which is in the connector box at the lower side of control panel assy in refrigerator compartment connected properly? (The 6-pin connector is connected to the motor damper. Refer to the Normal Yes Replace the motor damper for the chilled / refrigerator compartment. Normal Yes Clean up the area that found frost forming. Does the motor damper have a sign of frost forming? No Check the chilled thermistor. Dip the chilled thermistor into ice water (0°C), and disconnect the 2-pin connector leading from the thermistor attachment, and measure the resistance between the pin no. 1 (white) and 2 (white) terminals. • Resistance at 0°C : approx. 6-7 kΩ Resistance value abnormal The set temperature can be adjusted on the operation panel -> Refer to 6.1 [ (6)Setting adjustment mode] Replace refrigerator compartment thermistor. Press the both two side of door switch *1 If the food is cooled excessively, adjust the temperature setting for slide chilled case(low) (when supercool chilling is set) -> Refer to 6.1 [ (4) Temperature adjustment for slide chilled case (low) [ When supercool chiling is set ] R-room 6 pin connector REFCON ASSY [2] Slide chilled case (low) compartment Excessive cooling 4 pin connector 2 pin connector Motor damper for chilled / refrigerator Chilled thermistor 29 [3] Freezer compartment Poor cooling Is the set temperature of freezer compartment, set to ? No Set the temperature to No Proceed to " [6] The freezer fan motor does not work " Yes Does cool air blow from air outlet when opening the refrigerator compartment door and press the both two side of door switch ? Yes Check the freezer compartment thermistor. Resistance value abnormal [4] Compressor does not operate The set temperature can be adjusted on the operation panel -> Refer to 6.1 [ (6)Setting adjustment mode] Not cooling at all (No error code E50 - E57 appears even though Yes Is the refrigerator in the demonstration mode? Replace freezer compartment thermistor. REFCON ASSY Dip the freezer compartment thermistor into ice water (0°C), and disconnect the 2-pin connector leading from the thermistor attachment, and measure the resistance between the pin no. 1 (white) and 2 (white) terminals. • Resistance at 0°C : approx. 6-7 kΩ is touched for 5 seconds.) Release the demonstration mode. (Refer to 6.1(2)) No Is the terminal voltage 230 - 240 V AC across the terminals no. 1 and 3 in the CN1A connector on the control board? No Inspect power-supply wiring such as power cord and breaker. Yes Is the voltage 230 - 240 V AC across CN1A pin no.1 and CN4A pin no.1 on the control board? No Is the resistance about 0 Ω between terminals CN4A pin no. 1 and 3 ? Yes No Yes Open Replace the reactor. Detach connector CN50G on control board and check the resistance between each of the following terminals. pin no. 1, 3 and 5 : approx. 12.4Ω Check that the resistance between terminals CN2A pin no. 1 and 3 is open. No Replace the motor protector Measure the winding resistance of the compressor between each of the following terminals black, white and red : approx. 12.4Ω Abnormal Replace the compressor. Continuity detected Check the error display of selfcheck after turning off and on the power supply. **With all the connectors connected. Compressor Motor protector Reactor Inverter-related parts may have a trouble. Conduct the ice making test operation to check the error code. (See next page for error codes.) REFCON ASSY 30 Inverter-related indication “Compressor does not operate” Error code Abnormality Possible cause Symptom E50 Trouble of inverter circuit • There is any trouble in the circuit which detects phase current of compressor. The compressor does not rotate. Bus-bar voltage abnormality • Power supply The comvoltage is abnor- pressor mal. does not rotate. • Failure in the reactor E51 Corrective measures Replace the control board. Start 77 ~ 283 V Measure the power supply voltage. 283 V or more 77 V or less If the voltage is out of the 77 to 283 V range, domestic electrical wiring may have a failure. Take appropriate measures. Is the voltage about 230~ 240 V AC across CN1A pin no.1 & CN4A pin no.1 on the control board? (Refer to 6.7) No Is the voltage about 230~ 240 V AC across CN1A pin no.1 and CN4A pin no.3 on the control board? Yes Replace the control board. E52 No Is the voltage about 230~ 240 V AC across CN1A pin no.1 and CN2A pin no.3 on the control board? Yes The compressor does not rotate. Check the connection status between the power cord and the control board. Yes Replace the motor protector (Unplug the power cord and measure the resistance across CN2A pin no.1 and 3. Make sure that the resistance is open.) Replace the reactor. (Measure the resistance between the connector terminals of the reactor that are disconnected. Make sure that the resistance is open.) Trouble of • The inverter inverter software driving software reset function malfunctions due to electric noise. No Normal Replace the power cord. Unplug the power cord and wait more than 10 minutes then plug it again Check the error code by performing the ice making test operation. E52 displays again. Replace the control board. E53 • Abnormal start-up • The compressor motor gets locked. • Abnormal syn- • Defective circuit chronization on control board • Overcurrent detection The compressor does not rotate. No error code display Explain to customer. Start Measure Remove the CN50G the winding connector on the conresistance of trol board, and meascompressor ure the resistance No No between each on the compressor. terminal. Is Are the resistances the resistance between the terminals approx. 12.4 - , - , and (20 )? - approx. 12.4 (20 )? Yes Yes *Replace motor protector • Poor contact of CN50G on control board Check the connection *Is compressor No status of the CN50G energized at connector on the constartup? trol board. Yes Normal Replace the Replace the compressor. control board. Replace the compressor. Abnormal Correct the connection of the CN50G connector on the control board. *If control board is normal, compressor is energized every 10 minutes. The compressor vibrates at start up when it is being energized. Touch the compressor with your hand to check the vibration. 31 Inverter-related indication “Compressor does not operate” Error code E56 Abnormality Possible cause Symptom • Failed wiring • Poor connection continuity of connectors • Trouble of the related to comcontrol board pressor (on the board and the compressor.) • Failure in wiring connecting of the compressor • Trouble of control board • Trouble of compressor The compressor cannot be activated for more than 1.5 hours. Corrective measures 1. Locate the trouble and decide on the measures. • Decide the measures by checking the followings. (1) Poor connector connections. (On the board and the compressor.) (2) Winding resistance of compressor 2. Flowchart of troubleshooting Check Treatment start The connector CN50G on the control board is properly connected? No Connect it properly. Yes The connector of compressor is properly connected? Compressor Yes CN50G Control board Point+2 (to measure resistance) For checking the connection to compressor Point+1 (to measure resistance) For checking from refcon to compressor No Remove the CN50G connector on the control No board, and measure the winding resistance on the compressor. , and (Point1). Is the resistance approx. DW& " Yes Is compressor being energized at startup? Measure the winding resistance of compressor No between each terminal (Point 2). Is the resistance approx. DW& " Replace the compressor. Yes Replace the motor protector. No Replace the control board. Yes Replace the compressor. Replace the control P.C. board only when the error display keeps blinking even though all the above mentioned connectors are properly connected. 3. Recheck after corrective measures • After any measures are taken, unplug and plug power cord again to check that the compressor operates properly. • If the compressor operates properly for more than 1 minute after power cord is plugged again, it is presumed that the cause of trouble is eliminated. *If the cause of trouble cannot be eliminated, E56 will be displayed again 1 minute later after the power cord is plugged again. *If the control board has been replaced, E56 will not be displayed even though the cause of trouble is still not eliminated. In such a case, perform the ice making test operation to check what the error is. At the same time, also check that the compressor is operating for more than 3 minutes and each compartment is getting cooled. E57 Inverter drive module abnormality Overcurrent is Failure of the in the inverter drive mod- detected inverter drive ule in the control module before starting the com- Replace the control board. P.C. board pressor, and the compressor does not start rotating. 32 [5] Poor defrosting Poor cooling Short-circuit the terminal no. 1 and 2 of the compulsory defrosting terminals (CN7M) on the control board to actuate the compulsory defrosting function and check whether the defrost heater is working properly. (Refer to *1) Check the following and explain the result: half-open door, gap between gaskets, the amount of ice. Yes (heats up) No No Check that there is continuity between thermal fuse and defrost heater Replace the defrost heater and the thermal fuse. Yes Check the resistance of the defrost thermistor. 4 pin connector REFCON ASSY Freezer compartment fan motor 2 pin connector Thermal fuse 1 pin connector Defrost heater 1 pin connector *1 The compulsory defrosting will not work when the temperature of the defrost thermistor is 10°C or more. Defrost thermistor Yes Perform the self check. Check whether any error is displayed. No Unplug and plug the power cord and check whether the freezer fan motor is rotating. Interior LED is not turned Not rotating Check the door switch for continuity. • Open and close the refrigerator door (b) several times and check that the interior LED will be turned on and off (interior LED should get turned off when the door comes 10 mm close to the refrigerator body (a).) • Close the refrigerator compartment door until the LED is turned off(a) . Open and close the freezer compartment door (c), and from the space of refrigerator compartment door, check that the interior LED is turned on and off. Abnormal Check the continuity by disconnecting the CN9S on the control board. Normal Contact failure of connector. Connect it Check if the connector on the door switch is connected properly. If it is, replace the door switch. Interior LED is turned on and off properly Check whether the connector CN5D, CN9S on the control board and the 4-pin wire to wire connector for the fan motor on the freezer compartment are properly connected. No continuity Connect the connectors properly. Continuity detected Replace the freezer fan motor. 4 pin connector Freezer compartment fan motor REFCON ASSY [6] The freezer fan motor does not work 2 pin connector (b) 3 pin connector (R-room section) Door RL R-room door switch (a) 3 pin connector (R-room section) R-room door switch F-room reed switch (c) 33 Door RR After ice making test operation, does the error code 13(Refrigerator thermistor) / error code 18(A.T. thermistor) display? Error code 18 display Check the resistance for the A.T. thermistor which locate at display operation board that will be found open( )or short(0 ) circuit? Error code 13 display Yes Check the resistance for the refrigerator thermistor that will be found open( )or short(0 ) circuit? Check the resistance for vegetable heater(At control board between CN3A No.7(YellowGreen) and CN2A No.3(Gray)) will be found around 6.7 k or not? 0 or No Check the resistance for vegetable heater(At below of V-room between pin no.1&2 will be found around 6.7 k or not? Replace the display operation board.(This A.T. thermistor was included inside display operation board ; TH1 position) Yes Replace the Refrigerator thermistor Confirm the 6-pin connector which is in the connector box at the lower side of control panel assy in refrigerator compartment was connected properly or not.If not, please recorrect it. 0 or *Remark : Because of vegetable heater was locate inside divider VF of refrigerator. So, it cannot *Vegetable heater failure Yes Yes Repair the connection failure When the ambient temperature was below than 22 ºC and V-room temperature was below than 8 ºC, please set the temperature setting of both refrigerator room & vegetable room for Check input voltage at control board between CN3A No.7(Yellow- Green) and CN2A No.3(Gray)) will be have voltage for 220 VAC or not? (Voltage will not supply into vegetable heater in case of any of auto-ice maker, water supply pump motor, motor damper has opearation.) After voltage measure for more than 10 seconds, if it has reading for 220 VAC, it is OK.(Within 10 seconds period, it will repeatedly ON-OFF.(For example : 7 seconds ON / 3 seconds OFF repeatedly.) No Replace the control P.C. board Yes Refrigerator working normally (2) Confirm in case of found excessive cooling in Refrigerator room / Slide chilled case (Low) When found excessive cooling in Refrigerator room / Slide chilled case (Low). And also found excessive cooling in vegetable room. After proceeded the flowchart of trouble criterion([1]Refrigerator room / [2]Slide chilled case (Low). Please confirm about cooling excessive in Refrigerator room / Slide chilled case (Low) was not exist. OK Explain to end-user 2 pin connector Vegetable heater 6 pin connector REFCON ASSY [7] Vegetable compartment (Other include) Excessive cooling / Food frozen (1) Confirm about Thermistor / Vegetable heater / Control P.C. board(Refcon assy) 34 Refrigerator thermistor 6.6) TROUBLE CRITERION OF MAIN PARTS Components/ Parts Mounted Position Check Method and Criterion Part Name Compressor in EEI91E13DWH the machine W 37 (1620 rpm) chamber at the Starting current A 6.0 rear side of Rated current A 0.86 (1620 rpm) (For only 1 minute after start up) the frame Model Rated input Normal Abnormal (faulty) (Black-White) 16.72 Opened ( ) (White-Red) (20 ºC) or Short (0) Compressor Winding (Red-Black) Measure the resistance with a tester. (Ambient temperature:Room temperature 15oC ~ 25oC) Compressor in Model Connected Point Motor protector *Remark : Energize it at 17.0 A, 25ºC for 16 seconds at the longest. MM3-71CCY o Open 100 + 5 C or more* Close o 60 + 10 C or less Measure the resistance with a tester.(Ambient temperature:Room temperature 15oC ~ 25oC) Normal Abnormal(faulty) Less than 1 Opened () Measure the resistance with a tester.(Ambient temperature:Room temperature 15 oC ~ 25oC) Normal Motor damper for refrigerator compartment Winding (Blue-White, Red-Yellow) 35 415 Abnormal (faulty) Open () or short circuit (Approx.) (0) the machine chamber at the rear side of the frame In the control panel of the refrigerator compartment. Components/ Part Name Check Method and Criterion Parts Mounted Position Model 12537JE-13P-BU-F2 Type DC brushless o In the fan grille of the freezer compartment. o Measure the resistance with a tester.(Ambient temperature:Room temperature 15 C ~ 25 C) Freezer fan motor Normal Abnormal (faulty) Between 3 - 1 (GND and Between 3-1 : open( ) or Vcc): About 25k between 2-1 : short ( 0 ) Model 4715JL04WS16G51 Type DC brushless o o Measure the resistance with a tester.(Ambient temperature:Room temperature 15 C ~ 25 C) Machine chamber fan motor Normal Abnormal (faulty) Between 3 - 1 (GND and Between 3-1 : open( ) or Vcc): About 25k between 2-1 : short ( 0 ) o o Measure the resistance with a tester.(Ambient temperature:Room temperature 15 C ~ 25 C) Water supply pump motor (DC 5V) Normal 16 (Approx.) Measure the resistance with a tester. (Ambient temperature:Room temp. 15°C ~ 25°C) Rated input operation method Defrost Heater Abnormal (faulty) Open (or short Under the water tank holder in refrigerator compartment. circuit (0 170 W Power ON after defrosting (14 + 1.5oC or more) Normal Abnormal (faulty) 338.8 (Approx.) Opened () 36 In the machine chamber at the rear side of the frame. In the drip tray under the evaporator of the freezer compartment Components/ Part Name Parts Mounted Position Check Method and Criterion Measure the resistance with a tester according to the following graph. (Thermistor resistance values against temperature) Resistance measured under the ambient temperature from -50 oC to +50 oC 1. 200 to 500k ............normal (Defrost thermistor) Evaporator (Chilled thermistor) On the lower part of the control panel 2. Out of the above range ............abnormal (k 35 30 Refrigerator compartment, Freezer compartment, Defrosting, Chilled, Ice making 25 20 Thermistor Thermistor Check Procedure Thermistor resistance valves against temperature 15 Thermistor resistance will vary Outside air thermistor (In display board) with the change of temperature. Take the temperature around the thermistor, and then measure thermistor resistance using a tester. The relation between resistance Inner 10 and temperature is as shown on (Refrigerator compartment thermistor) In the control panel of refrigerator compartment the left side. 5 0 (Freezer compartment thermistor and Ice making tray thermistor) In Ice maker of freezer compartment -20 -10 10 0 Temperature 20 30 Trouble shooting with self-check (1) If the self - check indicates the abnormality of thermistor right after the power is turned on, measure the resistance of the thermistor. Vegetable compartment In the partition between freezing and vegetable compartments (Divider VF) If the circuit of thermistor is short , check the element of the thermistor and the contact of the connector. (2) When the self - check indicates the abnormality of thermistor a few seconds (Outside air thermistor) In the display board after the power is turned on , check the contact of the connector. Measure the resistance with a tester. Rotational Heater Board Between Red-Red Rated input At the beside of door RL Normal Abnormal (Faulty) 7.4 k (Approx.) Open () W 7.7 While compressor is operating, the heater turns on. When compressor stops, the heater is suspended for the first 20 minutes and then reactivated. Operation method Measure the resistance with a tester. (Ambient temperature:Room temperature 15°C ~ 25°C) Vegetable compartment heater Rated input Operation method Normal Abnormal (Faulty) 6.7 k (Approx.) Open () W 8.6 The heater turns on when vegetable compartment thermistor has reached a lower temperature than the set temperature for vegetable compartment. 37 At the bottom of the vegetable case(Inside poly-urethane foam ; PUF) *The connectors are in the connector box of V-room* Components/ Part Name Check Method and Criterion Parts Mounted Position Measure the resistance with a tester. Black Normal Water supply pipe heater Black Abnormal (faulty) 500~1500 At the left bottom of vegetable compartment Open () (20~30ºC) Rated input 0.9 W Operation method The heater turns on with the energization rate adjusted according to each setting for the R & F room. o o Measure the resistance with a tester.(Ambient temperature:Room temperature 15 C ~ 25 C) Normal Abnormal (faulty) 9.6k(Approx.) Open () Chilled heater Rated input 6 W Operation method Under supercool chilling setting, the heater is energized while the temperature is at or below the setting temperature of the chilled thermistor. o Embedded in the floor of the refrigerator compartment (The connector is in the left back of the refrigerator compartment.) o Measure the resistance with a tester.(Ambient temperature:Room temperature 15 C ~ 25 C) Ice maker heater Rated input Abnormal (faulty) 56k(Approx.) Open () 2 W Operation method Normal Ice maker heater will operate when ice maker thermistor detect temperature below than 5ºc 38 At the left bottom of vegetable compartment Components/ Part Name Interior LED (13.3 VDC) Check Method and Criterion LED lighting duration It lights up while the refrigerator compartment door is open. (If the door stays open for 60 minutes in a row, the LED automatically goes out. Once the door is closed, it will light up again next time the door is opened.) Parts Mounted Position On the ceiling of the refrigerator compartment(Upper side) and on the control panel (Lower side) (Interior LED control board) Abnormal criterion The LED does not turn on at the above timing. On the back side of vegetable compartment (Vegetable compartment LED board) Vegetable compartment LED 39 40 CN50G Compressor 1 U phase 3 V phase 5 W phase CN2A Motor Protector 1 3 AC 220-240V common CN1A 1 AC 230-240V 3 AC 230-240V 5 Functional earthing Inverter DC5V (At between word screen of DC5V-INV & GND-INV) Inverter drive power DC12~20V (At between word screen of DC15V-INV & GND-INV) CN4A 1 REACTOR 3 REACTOR CN3A 1 Water pipe heater 3 Chilled heater 5 Defrost heater 7 Vegetable heater 9 Rotational heater board Between no. 8, 9 on IC1A DC13.0~13.8V Power soure of drive circuit Bus-bar DC340V + and – on DS91C CN5D 1 GND 13.3V 2 Motor Damper for REF/Chilled room 3 Power 13.3V 4 Motor Damper for REF/Chilled room 5 Vegetable room LED 6 Motor Damper for REF/Chilled room 78 Motor Damper for REF/Chilled room 910 Ice maker heater 11 Freezer fan motor VS 12 13 Outer fan motor VS 14 Ice maker gear box (forward) 15 Freezer fan motor FG 16 Ice maker gear box (reverse) 17 Outer fan motor FG 18 Water pump motor (-) 19 Ice maker detection position sw 20 Water pump motor (+) CN105 No use 1 2 3 4 5 CN9S 12 Reed SW input for F-room 3 Power 5.0V 4 Door SW input for R-room 5 Transmission of operation panel data 67 Reception of operation panel data 89 GND5V 10 Interior LED in R-room Control DC5V (At between word screen of DC5V & GND) *Remark : When the temperature of the defrost thermistor is 14°C or more, compulsory defrosting does not turn on. Compulsory defrosting by short-circuiting* CN7M The capacitors, C91C and C92C, for the bus bar are charged at a voltage of 340 V DC. The electric charge remains for a while after the power cord is unplugged, so there is a risk of electric shock. Wait for 1 minute or longer after unplugging the power cord to allow the capacitors to discharge safely. After discharging the capacitors, measure the voltage across the testing points on the bus bar and make sure that the voltage is 10 V DC or less, and then conduct inspection and repairing. 6.7 TEST POINT DIAGRAM OF MAIN CONTROL BOARD 11 Ice making tray thermistor 12 13 14 Defrost thermistor 15 Chilled thermistor 16 Freezer themistor 17 18 Refrigerator thermistor 19 20 - 7 DISASSEMBLY INSTRUCTIONS MR-LXR68EM-R Plug out before work. Check the automatic ice-maker by pressing ice making stop switch. In assembling & disassembling parts use several kind of screws and rivets. Do not mistake to use them. A B 4 x12 Stainless steel C Rivet 4 x12 (Black) With metal washer OPERATING PROCEDURE PHOTOS Screw Rivet Screw ELECT COVER (1) Remove the fixing screw(10 screws) and the rivet(1 Rivet) on the elect cover on the back of the refrigerator.(See photo 1) Screw CONTROL BOARD (or REFCON ASSY) Screw Elect cover (2) Remove the control board by removing the connector. (See photo 2) Photo 1 Screw CAUTION ON INSTALLATION Reactor To prevent pinching of the lead wires and poor insertion of the connector, be sure to install the lead wires and connectors in the appropriate positions. Control board Tab REACTOR (3) Disconnect the connectors and disengage both left and right tabs.(See photo 2) Photo 2 Tab 9 fixing screw COMPRESSOR COVER (1) Remove 9 screws at the back side of refrigrator for dis-assembly compressor cover.(See photo 3) BOX FAN (AT MACHINE ROOM) (2) Remove the connector. (3) Pull out the box fan by removing the 1 fixing screw.(See photo4) Photo 3 DRAIN HOSE (ELBOW) (4) Remove drain hose from tab(u-shape) lock. And then put downward the drain hose for take out.(See photo 4) DRAIN PAN (5) Remove 1 screw.(See photo 4) CAUTION - Wash the drain pan with water when it is dirty. (6) Remove the drain pan while bending the pipes inside the drain pan upward. CAUTION (1) Avoid crushing the pipes. (2) When installation drain pan, please beding the pipes into original position(Provide clearance of 10-15 mm.) between the piping and the sides of the drain pan. (3) After bend pipe in drain pan finished, please assembly the drain hose into original position. (Must be lock complete in tab(U-shape)). 41 Elbow Tab (Elbow) Screw Box fan Drain pan Connector (box fan) Screw (Box fan) Photo 4 OPERATING PROCEDURE PHOTOS Part inside the refrigerator compartment (1) Remove interior parts from the refrigerator compartment : Glass shelf R assy(2pcs), Glass top plate assy, Chilled case door, Slide chilled case (up), Slide chilled case(low) (See photo 5) Partition C (2) Disengage the tabs on the right and the left of the partition for chilled compartment(Partition C) by lifting them up. (See photo 6) (3) Pull out the Partition C toward to you along with push it up. Glass shelf R assy Chilled case door Glass top plate assy Partition (C) Slide chilled case (up) Slide chilled case (low) Photo 5 Partition (C) Tab Tab Screw Photo 6 Connector box (3) Remove 1 screw and pull out the connector box toward to you. (4) Disconnect the connector inside bag(After remove bag) Cover up Control panel Cover low Screw Control panel, Duct R (5) Remove left and right screw(1 pc per each) at control panel and remove 2 screws below temp control board. And then you can remove control panel assy out by disengage both upper(2 positions) and lower(2 positions) tabs.(For LED light board, you can remove it by remove LED cover first.) (See photo 7) Remark : For cover up & low remove procedure. After you remove 3 screws at control panel finished, you can remove cover up & low from 4 position of tabs. Part inside the vegetable compartment (1) Remove interior parts from the vegetable compartment : Vegetable case, fruit case.(After that, remove door V assy out.) Vegetable case cover sub (Right) (2) Remove tab and slide vegetable case cover sub (Right) to inside (For left side is use same procedure as left side) (See photo 8) Screw Connecter Screw Tab Tab Photo 7 V Room (Right side) Tab Vegetable case cover sub (Right) Photo 8 V Room Duct V Duct V (3) Remove 3 screws and remove duct V. (See photo 9) Screw Photo 9 42 OPERATING PROCEDURE PHOTOS Vegetable case cover (4) Remove 6 screws and you can take vegetable case cover out.(See photo 10-1, 10-2) Water pump motor Water pump motor (5) Remove 2 screws and cut the lead wire for take out Screw water pump motor. (See photo 11) Screw Water pump motor Photo 10-1 Water pipe(upper side) Screw Photo 11 Part inside the freezer compartment (1) Remove interior parts from the freezer compartment : Freezing case up(With ice box sheet and ice spoon inside) and freezing case low. (2) Remove drawer F with door F out from F-room. Photo 10-2 Tab Cover (upper) Auto ice maker Tab Photo 12 Automatic Ice maker (3) Remove 3 tabs and remove cover (upper) out. (4) Disconnect the connnector. (5) Press the tab at the upper along with pull out the automatic ice maker to the right side and remove it. (See photo 12) Tab Tab Cover duct IM (6) Remove 2 tabs and remove cover duct IM (See photo 13) Cover duct IM Photo 13 Connector cover(FG) Connector cover (FG) (7) Remove 1 screw for dis-assemble the connector cover(FG).(See photo 14) (8) Remove bag and disconnect the connector inside bag. Cover duct IM Fan grille Screw Screw Screw(Connector cover(FG)) Photo 14 43 OPERATING PROCEDURE PHOTOS Fan grille (9) Remove left and right side screw (2 screws per each side.) (See photo 14) Heater roof,Defrost heater (10) Lift up the evaporator from catch no.1.(See photo 15) (11) Peel off the tape that fixes lead wires on the side wall of compartment. Then detach heater roof from catch no.2. Then remove defrost heater from groove no.3(See photo15) Drip tray Catch No.1(For evaporator) Catch No.2(For heater roof) Groove No.3(For defrost heater) Photo 15 Defrost thermistor binder Evaporator Defrost thermistor (12) Cut the binder and disconnect the connector.(See photo16) Caution on assembly 1) Loosen the lead wire at the defrost heater to prevent the water from entering the glass tube and careful the direction for correct assembly. 2) Attach the drip tray securely to the lower parts. 3) Attach the defrost thermistor in the correct place.(If they are attached out of place, thermal characteristics will go wrong.) 4) Attach the lead wires to the fixture. Defrost heater Photo 16 R-room Water tray Water pipe (upper) Photo 17 Water tray (1) Pull up the water tray from slot. And you can take out water tray with water pipe(upper) together.(See photo17) V-room Water supply pipe (lower) (2) Remove screw and then you can remove pipe cover. (See photo 18) (3) Disconnect the connector. And then you can remove the water supply pipe(lower) out.(See photo 18) Pipe cover Screw Water supply pipe (lower) Photo 18 44 OPERATING PROCEDURE ロ ロ ロ ロ ロ ロ Dryer ロ Compressor ロ ロ ロ Drain pan Charge pipe (Low pressure side) Charge pipe (High pressure side) 45 ロ Outer fan motor ロ 8 PARTS LIST DOOR PARTS MR-LXR68EM-R 46 DOOR PARTS No. 1 PART NO. RoHS PART NAMES KIEBK5704 <G> HINGE ATTACH UP KIEBK5009 <G> 2 DOOR RL KIEBK6009 <G> KIEBK5180 KIEBK5024 KIEBK6024 <G> DISPLAY PCB ASSY SET <G> DISPLAY COVER <G> 5 KIEV94747 <G> DOOR STOPPER LH 6 KIEPE4741 KIEBK5002 KIEBK6002 KIEBK5001 KIEBK6001 KIEBK5607 KIEBK5000 KIEBK6000 <G> CATCHER LH <G> DOOR V <G> <G> DOOR F <G> <G> SPRING (ROTATION HEATER BOARD) <G> DOOR RR <G> 3 4 7 8 9 10 11 KIEV94746 <G> DOOR STOPPER RH 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 KIEG05741 KIEBK5192 KIEBK5118 KIEBK5115 KIEBK6118 KIEBK5124 KIEBK5799 KIEBK5151 KIEBK5158 KIEBK6158 KIEBK5110 KIEBK5107 KIEBK5050 KIEBK6110 KIEBK5112 KIEBK6151 KIEBK5111 KIEV94447 KIEBK6107 <G> CATCHER RH <G> FUTA FREE POCKET <G> FREE POCKET S <G> EGG CASE <G> FREE POCKET M <G> BOTTLE POCKET <G> ROLLER (FRAME) <G> FRAME VF RH <G> FRAME REAR V <G> FRAME REAR F <G> MAGNET GASKET ASSY (RR) <G> PACKING RR DOOR IN <G> ROTATIONAL HEATER BOARD <G> MAGNET GASKET ASSY (RL) <G> MAGNET GASKET ASSY (V) <G> FRAME VF LH <G> MAGNET GASKET ASSY (F) <G> LEAD WIRE COVER <G> PACKING RL DOOR IN SPEC GSL 1 Without magnet gasket RL, rotational heater board assembly, display pcb assy set, lead wire cover with hinge up Include display board, frame, plate set GBK 1 1 1 1 1 1 1 Metal Part (Locate at bottom of door cap low of door RL) Plastic Part 1 1 1 1 1 1 1 1 1 1 1 1 Metal Part (Locate at bottom of door cap low of door RR) Plastic Part RECOMMEND PART NO. 2, 3, 7, 8, 10, 22, 25, 26, 28 ABBREVIATION F R Q'TY/UNIT MR-LXR68EM-R FREEZER ROOM REFRIGERATOR ROOM ENCIRCLED PART NUMBER ARE NOT SHOWN IN THE FIGURES. - Country code : R = RUSSIA - Colour code : GSL = GLASS SILVER, GBK = GLASS BRILLIANT BLACK 47 1 1 1 1 2 1 2 2 4 2 1 1 1 1 1 1 1 2 1 1 1 1 1 2 1 2 2 4 2 1 1 1 1 1 1 1 2 1 1 1 PRICE/PIECE (US$-FCA) BODY PARTS MR-LXR68EM-R 48 BODY PARTS Q'TY/UNIT No. PART NO. RoHS 1 2 3 4 5 6 7 8 10 11 12 KIEBK5326 KIEBK5858 KIEZ87807 KIEBK5802 KIEBK5818 KIEP89503 KIEZ87808 KIEBK5663 KIEP91708 KIEP90708 KIEZ87442 KIEBK5350 KIEBK5652 <G> ELECT COVER ASSY <G> CONTROL PANEL ASSY <G> CONNECTOR BOX <G> DUCT V ASSY <G> COVER DUCT V <G> WATER TRAY ASSY <G> CONNECTOR COVER (FG) <G> FAN GRILLE ASSY <G> LABEL FC <G> <G> PIPE COVER <G> AUTO ICE MAKER <G> COMP COVER ASSY 13 KIEZ87809 <G> LEAD COVER VF 14 15 16 17 36 37 38 39 KIE805794 KIEHJ3709 KIEZ87795 KIEZ87460 KIEBK5705 KIEV97705 KIEBK6705 KIEV95705 KIEV94701 KIEBK5811 KIEHJ4503 KIEHJ3531 KIEHJ3519 KIEK96527 KIEHJ3965 KIEHJ3520 KIEHJ3526 KIEBK5702 KIEBK6702 KIEBK5798 KIEBK5965 KIEHJ4442 KIEBK3730 KIEBK4730 KIEBK5730 KIEBK6730 KIEBK5669 KIEBK4805 KIEBK5805 KIEBK6805 <G> CASTER SET <G> SCREW LABEL (F) <G> CASTER ASSY <G> ADJUST FOOT <G> HINGE COVER LH <G> <G> HINGE COVER RH <G> <G> HINGE UP ASSY RH <G> PARTITION (C) <G> JOINT PIPE (TANK) <G> WATER TANK CAP <G> WATER PUMP <G> WATER TANK COVER ASSY <G> PACKING (TANK) <G> WATER TANK <G> FILTER (TANK) <G> HINGE LOW ASSY LH <G> HINGE LOW ASSY RH <G> ROLLER (RAIL VF) <G> PACKING F <G> COVER (IM) <G> KICK PLATE LH <G> <G> KICK PLATE RH <G> <G> DUCT COVER (IM) <G> COVER UP (CONTROL PANEL) <G> COVER MID (CONTROL PANEL) <G> COVER LOW (CONTROL PANEL) 40 KIEBK6663 <G> FAN GRILLE 41 KIEBK5662 <G> BELL MOUTH 42 KIEBK5327 <G> ELECT ATTACH 9 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 PART NAMES SPEC Include all of electrical part and plastic part. Include all of electrical part and plastic part. Lead wire cover locate at between divider VF and auto ice maker. MR-LXR68EM-R GSL GBK 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 2 2 2 2 1 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 1 1 Install inside F-room. (Front side of large plastic part at fan grille assy.) Install inside F-room. (Back side of large plastic part at fan grille assy.) Plastic part only. (Used for attach with refcon assy.) RECOMMEND PART NO. 8, 23, 25 ENCIRCLED PART NUMBER ARE NOT SHOWN IN THE FIGURES. ABBREVIATION F FREEZER ROOM R REFRIGERATOR ROOM R.H.B. ROTATIONAL HEATER BOARD 49 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PRICE/PIECE (US$-FCA) ACCESSORY PARTS MR-LXR68EM-R 50 ACCESSORY PARTS Q'TY/UNIT No. PART NO. RoHS PART NAMES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 KIEBK5429 KIEBK5479 KIEBK5413 KIEBK6413 KIEBK5418 KIEBK4409 KIEBK5409 KIEBK6409 KIEBK5406 KIEBK5405 KIEBK5468 KIEBK5467 KIEBK5474 KIEHJ3477 KIEBK5475 KIEBK5995 KIEBK5980 KIEBK5504 KIEBK5435 KIEZE1277 KIE902735 KIEHJ3797 <G> GLASS SHELF R ASSY <G> GLASS TOP PLATE ASSY <G> SLIDE CHILLED CASE (UP) <G> SLIDE CHILLED CASE (LOW) <G> CHILLED CASE DOOR <G> VEGETABLE CASE COVER <G> VEGETABLE CASE COVER SUB L <G> VEGETABLE CASE COVER SUB R <G> FRUIT CASE <G> VEGETABLE CASE <G> ICE BOX SHEET <G> ICE BOX <G> FREEZING CASE (UP) <G> ICE SPOON <G> FREEZING CASE (LOW) <G> EVAPORATOR <G> DRYER PIPE SET <G> ELBOW <G> DRAIN PAN <G> COMPRESSOR <G> U WASHER <G> RUBBER MOUNT SPEC EEI91E13DWH RECOMMEND PART NO. 1, 2, 3, 4 10, 13 ,15, 16, 17, 20 ENCIRCLED PART NUMBER ARE NOT SHOWN IN THE FIGURES. ABBREVIATION LEFT SIDE L R RIGHT SIDE 51 MR-LXR68EM-R GSL GBK 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 4 4 PRICE/PIECE (US$-FCA) ELECTRICAL AND UNIT PARTS MR-LXR68EM-R 52 ELECTRICAL & UNIT PARTS No. PART NO. 1 KIEBQ5339 2 KIEBK5363 3 KIEHJ3313 4 KIEBL3354 5 KIEZ87365 6 KIEV94312 7 KIEHJ3378 8 KIEHJ3469 9 KIEHJ3316 10 KIEZ87362 11 KIEBK5364 12 KIEBK5367 13 KIEMQ4363 14 KIEBK5336 15 KIEZ87320 16 KIEBK5537 17 KIEBK5392 18 KIEBK5538 19 KIEWD0340 20 KIEWD0341 21 KIEP89325 22 KIEBK5656 23 KIEZ91399 24 KIEBK5682 25 KIEBK5322 26 KIEBK6363 27 KIEBK5379 RoHS PART NAMES <G> REFCON ASSY <G> LED COVER TOP ASSY <G> THERMISTOR (R) <G> PLUG CORD ASSY <G> WATER PUMP MOTOR <G> THERMISTOR (DEF) <G> THERMISTOR (F) <G> GEAR BOX (IM) <G> THERMISTOR (I) <G> REED SWITCH <G> WATER PIPE ASSY <G> REACTOR <G> LAMP SWITCH (R) <G> THERMAL FUSE ASSY <G> FAN MOTOR ASSY <G> HEATER ROOF <G> DEFROST HEATER <G> DRIP TRAY <G> MOTOR PROTECTOR <G> PROTECTOR COVER <G> OUT FAN MOTOR ASSY <G> BELL MOUTH M ASSY <G> FILTER <G> DUCT DAMPER <G> THERMISTOR ( C ) <G> LED COVER LOW ASSY <G> VITAMIN UP SPEC 12537JE-13P-BU-F2 240V 170W MM3-71CCY 4715JL04WS16G51 Locate at between divider RV and vegetable case cover. RECOMMEND PART NO. 1, 2, 3, 6, 7 9, 14, 17, 19, 25, 26 ENCIRCLED PART NUMBER ARE NOT SHOWN IN THE FIGURES. 53 Q'TY/UNIT MR-LXR68EM-R GSL GBK 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PRICE/PIECE (US$-FCA) PACKING PARTS MR-LXR68EM-R NO STEP ON 6 C.F.B TOP COVER R L 2 TOP CUSHION 8 PAPER ANGLE 7 SIDE CUSHION ASSY 1 C.F.B BOX ASSY R L 3 PACKING COVER 4 BOTTOM CUSHION 5 C.F.B PALLET 54 PACKING PARTS No. 1 2 3 4 5 6 7 8 9 PART NO. RoHS KIEBQ5970 KIEBQ6970 KIEBQ5979 KIEV94973 KIEBK5978 KIEBK5974 KIEBQ5975 KIEBQ5971 KIEBK5977 KIEBK5969 PART NAMES SPEC <G> C.F.B BOX ASSY <G> <G> TOP CUSHION ASSY <G> PACKING COVER <G> BOTTOM CUSHION <G> C.F.B PALLET ASSY <G> C.F.B TOP COVER <G> SIDE CUSHION ASSY <G> PAPER ANGLE <G> CUSHION FOAM PS Locate at between below ref and C.F.B. pallet assy ENCIRCLED PART NUMBER ARE NOT SHOWN IN THE FIGURES. 55 Q'TY/UNIT PRICE/PIECE MR-LXR68EM-R (US$-FCA) GSL GBK 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 KANG YONG ELECTRIC PUBLIC COMPANY LIMITED. 67 Moo 11, Bangna-Trad Road Km.20, Bangplee, Samutprakarn 10540 Thailand. TEL : 0-2337-2900 FAX : 0-2337-2954 i i i http:www.m tsub sh -kye.com e-mail: [email protected] Printing Date : January 2019 ">
/
डाउनलोड
बस एक दोस्ताना अनुस्मारक. आप दस्तावेज़ को यहीं देख सकते हैं. लेकिन सबसे महत्वपूर्ण बात, हमारे एआई ने इसे पहले ही पढ़ लिया है. यह जटिल चीजों को सरल शब्दों में समझा सकता है, किसी भी भाषा में आपके सवालों के जवाब दे सकता है और सबसे लंबे या सबसे जटिल दस्तावेजों को भी जल्दी से नेविगेट करने में आपकी मदद कर सकता है.
विज्ञापन