advertisement
CIMCO PDM User Guide
CIMCO PDM User Guide -‐ www.cimco.com
1
License information
Information in this document is subject to change without notice and does not represent a commitment on the part of CIMCO Integration. The software described in this document may be used or copied only in accordance with the terms of the license. The purchaser may make one copy of the software for a backup, but no part of this user manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means electronic or mechanical, including photocopying and recording for any purpose other than the purchaser's personal use, without prior written permission from CIMCO Integration.
TERMS OF USE FOR:
Software: CIMCO PDM
Version: 1.x.x
Date: September 2011
Copyright (c) 2011 by CIMCO Integration
Notice:
CIMCO Integration reserves the right to make changes to the CIMCO PDM Software at any time and without notice.
Software License
You have the right to use the number of licenses of the enclosed program, which you have bought from CIMCO Integration. You may not distribute copies of the program or related documentation to any persons or companies. You may not modify the program or related documentation without the prior written consent of
CIMCO Integration.
Disclaimer of all Warranties and Liability
CIMCO Integration makes no warranties, either express or implied, with respect to the software, its quality, performance, merchantability, or fitness for any particular purpose. The entire risk as to its quality and performance is with the buyer. Should the CIMCO PDM software prove defective following its purchase, the buyer (and not CIMCO Integration, its distributor, or its retailer) assumes the entire cost of all necessary servicing, repair, of correction and any incidental or consequential damages. In no event will CIMCO Integration be liable for direct, indirect, or consequential damages resulting from any defect in the software, even if CIMCO
Integration has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of implied warranties or liability for
CIMCO PDM User Guide -‐ www.cimco.com
2
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
CIMCO PDM User Guide -‐ www.cimco.com
3
Notice:
The accompanying software is confidential and proprietary to CIMCO Integration.
No use or disclosure is permitted other than as expressly set forth by written
license with CIMCO Integration.
Copyright (c) 2011 CIMCO Integration. All rights reserved.
THIS SOFTWARE CONTAINS CONFIDENTIAL INFORMATION AND TRADE SECRETS OF
CIMCO INTEGRATION. USE, DISCLOSURE, OR REPRODUCTION IS PROHIBITED
WITHOUT THE PRIOR EXPRESS WRITTEN PERMISSION OF CIMCO INTEGRATION.
The CIMCO Logo is a trademark of CIMCO Integration. Microsoft, Windows, and
Windows NT are registered trademarks of Microsoft Corporation. Other brand and product names are trademarks or registered trademarks of their respective
holders.
Contacting CIMCO Integration
Address:
CIMCO Integration I/S
Vermundsgade 38A, 3
2100 Copenhagen Ø.
Denmark
Phone: +45 4585 6050
Fax: +45 4585 6053
E-‐mail: [email protected]
Web: http://www.cimco.com
CIMCO PDM User Guide -‐ www.cimco.com
4
Contents
What is CIMCO PDM? .......................................................................................... 6
Installation and first run .................................................................................... 7
Program Overview ................................................................................................ 9
Menus and toolbars ......................................................................................... 9
Explorer
.............................................................................................................. 12
The Database Configuration ........................................................................... 13
Client Configuration ...................................................................................... 14
Search Fields
.................................................................................................... 17
External Applications
..................................................................................... 19
Level Settings
................................................................................................... 21
Database Fields
............................................................................................... 23
Level File Handling
......................................................................................... 24
Applications
...................................................................................................... 27
Predefined Fields
............................................................................................. 29
Level Sync
......................................................................................................... 31
Status Configuration
....................................................................................... 33
Machines
............................................................................................................ 36
Directories
......................................................................................................... 38
CAM Files
........................................................................................................... 40
NC Files
.............................................................................................................. 42
Program Format
............................................................................................... 45
Associated Files
.............................................................................................. 46
Other Files
......................................................................................................... 48
Auto-Import
....................................................................................................... 50
Advanced
........................................................................................................... 52
Transfer
.............................................................................................................. 53
User Groups
...................................................................................................... 54
Users
................................................................................................................... 57
Database Configuration
................................................................................. 60
Database Server
.............................................................................................. 62
Show Columns
................................................................................................. 64
CIMCO PDM User Guide -‐ www.cimco.com
5
What is CIMCO PDM?
CIMCO PDM is a data management tool for organizing and managing CAM-‐files and related production documents. It is highly customizable and can be configured exactly to match your existing production workflow.
With CIMCO PDM you get all the functionality you would expect from a modern information management system and then some. It allows you to gather, structure and centralize your production documents. Transfer production documents e.g. setup sheets, tool lists, pictures and other essential information directly to the shop floor. Manage permissions for users and groups and centralize the backup and recovery of documents from previous versions.
Structuring production documents in CIMCO PDM works similar to how you structure files in e.g. Microsoft Windows -‐ with folders and sub-‐folders. CIMCO
PDM, however, allows you to specify exactly what types of files can be added to your folders and who has permission to do so. This ensures that your files will always be placed in the right folders in your structure.
CIMCO PDM, however, works with the concept of “levels” instead of folders. Levels can contain sub-‐levels and production documents can be associated with levels in several ways, such as physically copying or simply linking to documents in their existing location on a hard disk or network share. You can associate all types of production documents to a level such as images, tool lists, setup sheets, inspection notes, etc. or create them automatically by letting CIMCO PDM analyze the data contained in e.g. your CNC program.
CIMCO PDM has a lot more to offer than what has been outlined above. Its flexible and highly configurable nature makes it adaptable to any existing setup or workflow.
CIMCO PDM User Guide -‐ www.cimco.com
6
Installation and first run
Under the hood CIMCO PDM utilizes the powerful CIMCO NC-‐Base Database Server and CIMCO PDM Server as an intermediate layer for handling the communication between CIMCO PDM and the NC-‐Base Database Server.
CIMCO PDM
|
CIMCO PDM Server
|
CIMCO Database Server
In order to get CIMCO PDM up and running you need to install both CIMCO PDM and CIMCO Database Server. Both are available for download at www.cimco.com, but require a valid activation keyfile to run. CIMCO Database Server is installed as part of CIMCO Software Version 6.
Once you have completed installation and activation of CIMCO PDM and CIMCO
NC-‐Base Database Server you need to start both the NC-‐Base Database Server and
CIMCO PDM Server. It is important you do this in the right order as described
below:
Note: In Windows 7 and Vista you need to right-‐click and select “Run as
Administrator”.
1. Navigate to folder CIMCO, then to folder NCBase6. Run NCBaseServer and click the “Start” button to start the server.
2. Navigate to folder CIMCO, then to folder PDM6. Run PDMSetup and click
“Start Server”.
3. In folder PDM6, run CIMCO-‐PDM
The first time you run the above you will be prompted for an activation keyfile. If you do not have a keyfile please contact your local reseller or CIMCO Integration directly.
CIMCO PDM User Guide -‐ www.cimco.com
7
When you run CIMCO PDM you will be presented with the following screen. The upper part contains the “Database” toolbar and menus and the lower part contains a blank area reserved for the PDM “Explorer”.
1. Click on “Explorer” in the “Database” toolbar
2. Logon as “ADMIN” and leave the password field empty
If logon was successful you will see the following screen and can start using CIMCO
PDM.
CIMCO PDM User Guide -‐ www.cimco.com
8
Program Overview
In CIMCO PDM the screen is divided into two areas containing the “Menus and toolbars” and the “Explorer”. The topmost area contains the menus and toolbars.
These are dynamic and change depending on what is selected in the Explorer. The large area underneath contains the Explorer with its Search panel (left), Explorer
View (top, right) and Database Preview (bottom, right).
Menus and toolbars
CIMCO PDM Icon
Clicking this opens a small window with a shortcut to the Explorer and Database Configuration.
Database and Help (top menu)
Positioned at the very top of the screen the “Database” and
“Help” menus provide easy access to adding new projects, managing customers, accessing the Online Help and the About dialog.
CIMCO PDM User Guide -‐ www.cimco.com
9
Explorer
By clicking the “Explorer” icon you can logon to the Explorer. In the Logon dialog you first select the user you want to logon with
and then supply the correct password. The Explorer will open once logon is successful.
Add
By clicking the “Add” icon you can add a new root-‐level entry to the Explorer View. By default the root-‐level entry is called
“Project”, but this can easily be re-‐configured if you have
different naming requirements.
Clicking “Add” by default brings up the Project dialog where
Project name, Customer and Status is entered. In the Database
Configuration under Level Se1ngs you can add more database fields if needed and these will show in the Project dialog as well.
Logoff
Clicking the “Logoff” icon closes the Explorer and logs off the user.
Find next
If a search, using the Search panel, results in more than one result, the “Find next” icon will show the next result in the
Explorer View. That way you can easily move through your search results.
Info
Clicking the “Info” icon brings up a dialog with the information and database fields for the level or document selected in the
Explorer View. This can also be achieved by double-‐clicking a level in the Explorer View. You can change the information if needed and save/close the information by clicking the “OK” button.
Copy
Clicking the “Copy” icon makes a copy of the level or document selected in the Explorer View. Insert the copy by right-‐clicking the level in the Explorer View to which it should be inserted and click
“Insert”.
CIMCO PDM User Guide -‐ www.cimco.com
10
Backup
Clicking the “Backup” icon makes a backup of the selected level and its sub-‐levels in the Explorer View. Verify that the backup has
been performed by clicking the “Restore” icon. This brings up the
Restore dialog with a list of the backups.
Restore
Clicking the “Restore” icon opens the Restore dialog. This shows the backups that have been created for the selected level in the
Explorer View. Select the backup you wish to restore and click
“Restore”.
Send
Clicking the “Send” icon transfers the selected document in the
Explorer View to a predefined machine. Machines can be configured in the Database Configuration dialog.
Lock / Unlock
Clicking the “Lock” or “Unlock” icon locks/unlocks the selected level or document for editing by other users.
Delete
Clicking the “Delete” icon deletes the selected level or document and everything associated with it.
CIMCO PDM User Guide -‐ www.cimco.com
11
Explorer
Search panel
The Search panel is positioned in the left side of the Explorer. Fill out any or all of the fields available and click the “Search” button. The search results will show in
the Explorer View and you can navigate through them using the “Find next” icon in the toolbar. Click the “Delete” button to clear all the search fields.
The available search fields can be customized in the Database Configuration dialog.
The “Advanced Search” checkbox at the bottom shows the date fields for searching by dates or time periods.
Explorer view
The Explorer View is positioned in the top-‐right side of the Explorer. The first column in the Explorer View shows your root-‐level entries. By default these are called Projects and can be expanded by clicking the small (+) icon next to a project name. This reveals any sub-‐level documents and these can again have sub-‐level documents beneath them. There is no limit as to how many levels can exist.
The Explorer View also contains a number of additional columns with details for the documents in the first column e.g. Customer name, Machine group and Status. The columns shown can be configured in the Database Configuration dialog.
Double-‐clicking a level in the Explorer View brings up a dialog with the information and database fields for that level. Double-‐clicking a document opens it in an external program e.g NC-‐programs open in CIMCO Edit while CAD files open in
Mastercam -‐ this is completely configurable.
Right-‐clicking a document in the Explorer View brings up a contextual menu with relevant functions for that document. Many of the functions in the contextual menu have already been explained above.
Database Preview The Database Preview is positioned in the bottom-‐right side of the Explorer. It provides a dynamic preview of the selected level or document in the Explorer View. The amount of information depends on the selected level or document in the Explorer View. The left side of the Database Preview shows the related database fields and information. The right side shows a preview of the contents of the selected document. It also provides an overview of the documents
associated with the selected document (documents in sub-‐levels). Finally it provides a Log with history tracking of changes to the particular document.
CIMCO PDM User Guide -‐ www.cimco.com
12
The Database Configuration
All dialogs in the Database Configuration are accessed as follows:
To launch the Database Configuration dialog, either click on the CIMCO Icon to open the Shortcut Window and then on the Database Configuration Icon
, or directly click the small Dialog Launch Icon in the lower right corner of the Database Toolbar.
The Database Toolbar
Note: To be able to configure the database you must have access to the
PC where the PDM Client is installed, as well as administrator access to the database.
Now, in the dialog tree in the left window of the appearing dialog, click the dialog you want to view/edit. Expand the dialog tree as needed by clicking "+".
CIMCO PDM User Guide -‐ www.cimco.com
13
Client Configuration
The PDM Client is the interface to the database.
The Client Configuration dialog
Client Configuration
Path Relative to Main Directory
Check this box to specify the path to be relative to the main directory.
Remember Password
Check this box to log on automatically.
Note: This option will deactivate automatic log-‐off.
CIMCO PDM User Guide -‐ www.cimco.com
14
Open Information on Double-‐Click
When this box is checked, double-‐clicking a level will show its details. If the object is a file, the double-‐clicking will cause the associated program to open it. Associated programs can be set in the Default Program control panel.
Create Backup Before Open
Checking this box will automatically create a back-‐up of a file before it is opened.
Create a Backup Before Delete
Checking this box will automatically create a back-‐up of a file before it is deleted.
Open PDM Explorer on Start-‐up
Check this box to have the PDM Explorer automatically open on start-‐up.
Show File Extensions
Check this box to show file name extensions in the Explorer.
Show File Type
Check this box to show file type in the Explorer.
Show CAM Preview
If this box is checked a preview of the associated machine is shown.
Use Windows Login Name
Use same login name as for Windows.
CAD/CAM Setting
Select which application is used to show CAD/CAM images.
Max. Search Results
Enter a number here to limit the maximum number of search results presented in the explorer.
Auto-‐Logoff Time
Specifies the time in minutes that you will stay logged-‐in without keyboard entries or mouse movements. Zero (0) de-‐activates Auto-‐
Logoff.
Note: This option is not available when the option "Remember
Password" is active.
CIMCO PDM User Guide -‐ www.cimco.com
15
Language
From the list, select the language that you want CIMCO PDM to use.
Preview Picture Size
Defines the width of the pictures pre-‐viewed from levels.
Default Values
Click this button to return to default values.
OK
Click OK to accept settings.
CIMCO PDM User Guide -‐ www.cimco.com
16
Search Fields
This dialog is where you customize your Search Panel to show the search fields you want to use. In the dialog the search fields have been divided into two groups,
Global and Level. All refer to what is shown in the Explorer View, depending on
your Explorer View settings.
The Search Fields dialog
Global Search Fields
Customer
Check this field to activate the Customer search field in the Explorer
Search Panel.
CIMCO PDM User Guide -‐ www.cimco.com
17
Status
Check this field to activate the Status search field in the Explorer Search
Panel.
Machine Group
Check this field to activate the Machine Group search field in the Explorer
Search Panel.
Level Search Fields
Level
From the scroll-‐down menu, select a level. In the pane below, one or more boxes within each level can be checked to make the corresponding sub-‐level searchable from the Search Panel.
CIMCO PDM User Guide -‐ www.cimco.com
18
External Applications
This is where you determine, which external applications should be executable from within CIMCO PDM, and which external applications you want to be able to open your files when right-‐clicking levels (the "Open with..." function).
The External Applications dialog
CIMCO PDM User Guide -‐ www.cimco.com
19
External Applications
Application 1, 2, and 3
Enables easy start of up to 3 external applications from inside CIMCO
PDM's menu.
Enter path or browse for the executable file of the preferred application.
An icon of the application will be placed in the toolbar section next time you run CIMCO PDM.
Level Specific Applications
Applications 1 through 6
Enter path or browse for the executable file of the preferred application.
Ext. / Level
In the first field, type your name for the application.
In the second field, type which file extensions are allowed to be opened using the specified application (nc, txt, jpg, ...).
From the list in the third field, select at which levels the application can be executed.
CIMCO PDM User Guide -‐ www.cimco.com
20
Level Settings
This dialog is where you define levels – their names, icons, how they are related,
and where they are found.
The Level Settings/Level Configuration dialog
Level Configuration
Level
From the list, select the level to be configured.
Caption
Write/edit the name of the level.
Icon
CIMCO PDM User Guide -‐ www.cimco.com
21
Click on the icon to select a new one from file.
Icon Static/Icon Dynamic
Toggles if the icon is allowed to move, change shape, style, form, position, or colour.
Allowed Sub-‐levels
The sub-‐levels assigned to this level, as selected from:
Available levels
The pool of levels that have not already been selected for the "Allowed
Sub-‐levels" group.
Level Description
Select parent level and level type.
Level Directory
Here is default entered the variables for Root and Levelname, but an absolute placement can be browsed by clicking the Folder icon , or you can check Prefer Machine Directories, which will use the directories configured in the machine configuration.
CIMCO PDM User Guide -‐ www.cimco.com
22
Database Fields
Database fields can be used to set up user defined database fields for the selected
level.
The Database Fields/User-‐defined fields dialog
Level
Level
Select level from the list.
Database Fields
Database Fields
CIMCO PDM User Guide -‐ www.cimco.com
23
Enter field names in database fields.
OK
Click OK to accept settings.
Level File Handling
For all levels that contain a file you can configure how the filename should be generated, assign a default file template, and define the standard behaviour when
the file is added.
Level
The Level File Handling dialog
CIMCO PDM User Guide -‐ www.cimco.com
24
Level
Select the level file name from the list.
File Name
File Name Prefix
In this field you enter the prefix to the file name.
Digits
The number of digits in the file name. If you enter the value "5" the file names – between the prefix and extension entered – will be 00001,
00002, etc.
Note: This function is used for the generation of file names and is only
Extension
active when "Generate File Name" is selected in the field "Default File
Name" of the below section "Default Settings".
The file name extension you want to be default.
Steps
The number with which you want each new file name -‐ as generated using the number of digits specified under "Digits" – to be higher than the preceding file name. An increment value of 5 would cause the file names to be created as 00005, 00010, 00015, etc.
Next Number
Enter the next number to be generated.
File Template
Default Template
The template directory for this machine.
Click on the folder icon
Default Settings
to specify a directory.
CIMCO PDM User Guide -‐ www.cimco.com
25
Default File Action
Select from the list what should happen to Level files when stored in the
database.
Default File Name
Select from the list how Level files should be named when stored in the
database.
Default Path
The default path from which files should be opened.
Click on the folder icon to specify a directory.
Default Values
Click this button to insert the default values in all fields.
OK
Click OK to confirm the values and close the dialog.
CIMCO PDM User Guide -‐ www.cimco.com
26
Applications
For every level that contains a file, a default application can be set up that is used
to open the file on double click.
The Applications/Default Application on Double-‐Click dialog
Level
Level
Select the level file name from the list.
Default Application on Double-‐Click
Application
CIMCO PDM User Guide -‐ www.cimco.com
27
Enter the path of the preferred application, or click on the folder icon
to browse for it.
Create Datafile
Check this box to automatically have a datafile created.
Datafile Template
When "Create Datafile" is checked, in this field enter the path of the preferred template, or click on the folder icon
Destination Directory
to browse for it.
When "Create Datafile" is checked, in this field enter the path of the
destination directory, or click on the folder icon
Default Values
to browse for it.
Click this button to insert the default values in all fields.
OK
Click OK to confirm the values and close the dialog.
CIMCO PDM User Guide -‐ www.cimco.com
28
Predefined Fields
Once a database field is set up predefined values can be configured.
The Predefined Fields dialog
Level
Level
Field
Select level from list.
Select field from list.
CIMCO PDM User Guide -‐ www.cimco.com
29
V
alues
Value
Select predefined value or write a new one in the bottom field, enter by
clicking on the check mark button .
Default Values
Click this button to insert the default values in all fields.
OK
Click OK to confirm the values and close the dialog.
CIMCO PDM User Guide -‐ www.cimco.com
30
Level Sync
If there are two or more database fields with the same meaning in different levels,
these can be synchronised to avoid unnecessary manual entries.
The Level Sync dialog
Level
Level
Select level from list. This is the destination level for the selections made below.
CIMCO PDM User Guide -‐ www.cimco.com
31
Values
Select from lists to enter the values for Destination Field, Source Level, and Source
Field respectively.
Dest. Field
Select destination field.
Source Level
Select source level.
Source Field
Select source field.
Enter selections by clicking on the check mark button .
Default Values
Click this button to insert the default values in all fields.
OK
Click OK to confirm the values and close the dialog.
CIMCO PDM User Guide -‐ www.cimco.com
32
Status Configuration
For every single level an unlimited count of status can be set up, each containing actions like locking NC files or set a transfer limit. It is also possible to send emails when a status changes.
The Status Configuration/Level Status dialog
Status Configuration
Level
Select level from list.
CIMCO PDM User Guide -‐ www.cimco.com
33
Status Group
Select status group from list.
Delete
Delete selected status group.
Add
Add a status group.
Status
Select a status from list.
Status Name
Create status name.
Status Following
Allowed status to change to.
Status Available
List of available status for the selected level.
NC File Lock
Lock NC file when status gets active.
NC File Unlock
Unlock NC file when status gets active.
Enable Transfer Limit
Enable transfer limit for NC file when status gets active.
Disable Transfer Limit
Disable transfer limit for NC file when status gets active.
NC-‐Base Status
Change NC-‐Base status for NC file when status gets active.
Send E-‐mail
Select from list the user group to receive emails on status changes.
Delete
Delete status.
CIMCO PDM User Guide -‐ www.cimco.com
34
Add
Add status.
Default Values
Click this button to insert the default values in all fields.
OK
Click OK to confirm the values and close the dialog.
CIMCO PDM User Guide -‐ www.cimco.com
35
Machines
The Machines dialog offers functions to connect a defined group of machines to a
DNC interface (DNC-‐Max).
In CIMCO PDM you can dedicate projects, CAD files, CAM files, NC programs to a certain group of machines, which again is tied to a DNC interface. Directly from the control, you can then store NC programs in the database as well as request them
(only possible with the DNC-‐Max functions Auto-‐Receive and Remote Request).
The Machines dialog
Machines
A list of the machines stored in the database.
CIMCO PDM User Guide -‐ www.cimco.com
36
Machine
The name of the machine group.
Data Directory
Shows the path of the Data Directory.
Delete
Click this button to delete the machine group highlighted in the list.
Add
Click this button to add a machine group to the list. The following dialog appears:
OK
The Add New Machine dialog
Give the machine group an indicative name and complete by clicking
"Add". The Add New Machine dialog will disappear and your new machine group is added to the Machines dialog.
Click OK to confirm the new Machines set-‐up and close the Database
Configuration dialog.
CIMCO PDM User Guide -‐ www.cimco.com
37
Directories
In this dialog you define the environment variables for storing CAM-‐, NC-‐, and
other files.
The Directories dialog
Main-‐ and Backup Directories
Machine
A list of the machine groups stored in the database. Select a machine group to specify the corresponding directories.
Machine Directory
The start directory for this machine interface.
CIMCO PDM User Guide -‐ www.cimco.com
38
The $MACHINENAME variable will take the value entered here. All other variables for interface directories are default defined in relation to the
$MACHINENAME variable.
The initial value is $ROOT\$MACHINEGROUP.
Click on the folder icon
Backup Directory
to specify a directory.
Default value is $MACHINENAME\BACKUP.
Click on the folder icon
CAM Files Directory
to specify a directory.
Default value is $MACHINENAME\CAM.
Click on the folder icon to specify a directory.
NC Files Directory
Default value is $MACHINENAME\NC.
Click on the folder icon to specify a directory.
Other Files Directory
Default value is $MACHINENAME\OTHER.
Real Path
Click on the folder icon to specify a directory.
When the cursor is placed in any of the directory variable fields, Real
Path shows which actual path the variable refers to.
Default Values
Click Default Values to insert the default values in all the directory fields.
OK
Click OK to confirm the Directories values and close the dialog.
CIMCO PDM User Guide -‐ www.cimco.com
39
CAM Files
In this dialog you define how the names of CAM files and their templates are
handled.
The CAM Files dialog
File Name
Machine
Lists the machines stored in the database. Select a machine from the list to edit its CAM files set-‐up.
File Name Prefix
In this field you enter the prefix to the file name.
CIMCO PDM User Guide -‐ www.cimco.com
40
Digits
The number of digits in the file name. If you enter the value "5" the file names – between the prefix and extension entered – will be 00001,
00002, etc.
Note: This function is used for the generation of file names and is only active when "Generate File Name" is selected in the field "Default File
Extension
Name" of the below section "Default Settings".
The file name extension you want to be default.
File Template
Template
The template directory for this machine.
Click on the folder icon
Default Settings
to specify a directory.
Default File Action
Select from the list what should happen to CAM files when stored in the
database.
Default File Name
Select from the list how CAM files should be named when stored in the
database.
Default Path
The default path from which files should be opened.
Click on the folder icon
Default Values
to specify a directory.
Click Default Values to insert the default values in all fields.
CIMCO PDM User Guide -‐ www.cimco.com
41
OK
Click OK to confirm the values and close the dialog.
NC Files
In this dialog you define how the names of NC files and their templates are
handled.
The NC Files dialog
CIMCO PDM User Guide -‐ www.cimco.com
42
File Name
Machine
Use Level Settings
Use the same settings as are stored under Level Settings/File Handling
(see this dialog).
File Name Prefix
In this field you enter the prefix to the file name.
Digits
Lists the machines stored in the database. Select a machine from the list
to edit its NC files set-‐up.
The number of digits in the file name. If you enter the value "5" the file names – between the prefix and extension entered – will be 00001,
00002, etc.
Note: This function is used for the generation of file names and is only active when "Generate File Name" is selected in the field "Default File
Name" of the below section "Default Settings".
Extension
The file name extension you want to be default.
Increment
The number with which you want each new file name -‐ as generated using the number of digits specified under "Digits" – to be higher than the preceding file name. An increment value of 5 would cause the file
names to be created as 00005, 00010, 00015, etc.
Next Number/Increment
Enter the next number to be generated.
File Template
Template
The template directory for this machine.
Click on the folder icon to specify a directory.
CIMCO PDM User Guide -‐ www.cimco.com
43
Default Settings
Default File Action
Select from the list what should happen to CAM files when stored in the
database.
Default File Name
Select from the list how CAM files should be named when stored in the database.
Default Path
The default path from which files should be opened.
Click on the folder icon
Default Values
to specify a directory.
Click Default Values to insert the default values in all fields.
OK
Click OK to confirm the values and close the dialog.
CIMCO PDM User Guide -‐ www.cimco.com
44
Program Format
In this dialog you define how the names of NC files and their templates are
handled.
The Program Format dialog
Field Configuration
Machine
Lists the machines stored in the database. Select a machine from the list to edit its NC files set-‐up.
Insert after
The line in the NC file, after which the contents of the selected database field should be inserted.
CIMCO PDM User Guide -‐ www.cimco.com
45
Database Field
Select from the list the database field, the contents of which should be inserted.
Activate Trigger
Check this box to activate the trigger specified in "Start Trigger"/"End
Trigger" in the below sub-‐section.
Associated Files
In this dialog you define where the associated files and their templates are placed.
The Associated Files dialog
CIMCO PDM User Guide -‐ www.cimco.com
46
Associated Files
Machine
A list of the machine groups stored in the database. Select a machine group to specify the corresponding directories.
Directory Other Files
Default value is $MACHINENAME\OTHER.
Click on the folder icon to specify a directory.
Directory Tool Data
Default value is $MACHINENAME\TOOL.
Click on the folder icon
Tool List Template
to specify a directory.
The template directory for this machine.
Click on the folder icon to specify a directory.
Directory Memo Data
Default value is $MACHINENAME\MEMO.
Click on the folder icon to specify a directory.
Memo Template
The template directory for this machine.
Real Path
Click on the folder icon to specify a directory.
When the cursor is placed in any of the directory variable fields, Real
Path shows which actual path the variable refers to.
Default Values
Click Default Values to insert the default values in all the directory fields.
OK
Click OK to confirm the Directories values and close the dialog.
CIMCO PDM User Guide -‐ www.cimco.com
47
Other Files
In this dialog you define how other files are named and handled.
The Other Files dialog
File Name
Machine
A list of the machine groups stored in the database. You specify Other
Files for the machine group selected here.
File Name Prefix
In this field you enter the prefix to the file name.
CIMCO PDM User Guide -‐ www.cimco.com
48
Digits
The number of digits in the file name. If you enter the value "5" the file names – between the prefix and extension entered – will be 00001,
00002, etc.
Note: This function is used for the generation of file names and is only active when "Generate File Name" is selected in the field "Default File
Name" of the below section "Default Settings".
Default Settings
Move File
Check this box to move files to the designated directory instead of copying them there.
Default File Action
Select from the list what should happen to other files when stored in the
Default Path
The default path to which files should be stored.
database.
Click on the folder icon
Default Values
to specify a directory.
Click Default Values to insert the default values in all fields.
OK
Click OK to confirm the values and close the dialog.
CIMCO PDM User Guide -‐ www.cimco.com
49
Auto-Import
This dialog describes how to set up the auto-‐import of NC files.
The Auto-‐Import dialog
File Name
Machine
A list of the machine groups stored in the database. Select a machine group to specify its auto-‐import settings.
Start Trigger
This is where you define the CAM file's start trigger.
Example: "(CAMFILE="
CIMCO PDM User Guide -‐ www.cimco.com
50
End Trigger
This is where you define the CAM file's end trigger.
Example ")"
Import Delay
Use this field to specify the time in milliseconds to wait before importing data.
Allowed Extensions
Extension names allowed for the files to be imported.
Remove Trigger
Remove trigger from file before storage.
Generate Tool List
Check this box to have a tool list generated on basis of the imported file.
Tool List Extensions
Extension names allowed for tool lists.
Field Name
List of all import directories defined for the chosen machine group.
Move
Generate
Move file to the import directory (as opposed to copy –> YES).
Check this option to generate a new filename on auto-‐import.
Delete
Delete the highlighted import directory.
Change
Change the highlighted import directory.
Add
Add an import directory.
Default Values
Click Default Values to insert the default values in all fields.
CIMCO PDM User Guide -‐ www.cimco.com
51
OK
Click OK to confirm the values and close the dialog.
Advanced
Advanced Machine Settings.
The Advanced dialog
Machine
A list of the machine groups stored in the database. Select a machine group to specify its advanced settings.
CIMCO PDM User Guide -‐ www.cimco.com
52
Comment
Insert the start / end trigger for machine specific comments
Tool Trigger
Insert the tool trigger.
Transfer
Transfer Settings
The Transfer dialog
Machine
A list of the machine groups stored in the database. Select a machine group to specify its transfer settings.
CIMCO PDM User Guide -‐ www.cimco.com
53
Use CIMCO PDM
Use CIMCO PDM to send files to the machine.
Create WPD Folder
Create a WPD Folder for Siemens controllers.
Delete After
Clear the send directory after selected time?
Send Directory
Specify the path of the send directory.
User Groups
This is where you set up user access.
The definition of multiple users with different access rights has some advantages:
1. The number of individuals that can change settings in CIMCO PDM is limited.
2. The regular user cannot accidentally change important configuration settings, or – depending on the configuration – delete any project, CAD file, part, CAM file, etc.
3. Optional monitoring of program changes by individual users.
4. Optional assignment of individual access rights for selected users.
CIMCO PDM User Guide -‐ www.cimco.com
54
The User Groups dialog
User Groups
Group Name
List of all groups.
Users
List of members belonging to each group.
Delete
Deletes the highlighted user group.
Add
Adds a user group. A dialog will pop up, where you enter the name of the new group.
CIMCO PDM User Guide -‐ www.cimco.com
55
User Rights
Check the boxes in this list to allow the highlighted user group access to the corresponding functions.
Select All
Select all check boxes in the User Rights section.
Deselect All
Deselect all check boxes in the User Rights section.
Allowed Groups
Check the boxes in this list to allow the highlighted user group user rights within
the corresponding machine group.
Default Values
Click Default Values to insert the default values in all fields.
OK
Click OK to confirm the values and close the dialog.
CIMCO PDM User Guide -‐ www.cimco.com
56
Users
Here is where you enter users and user data, and give users access by registering
them with the appropriate user groups.
The Users dialog
User Info
Here is listed the registered users and their details.
Edit
Click this button to edit the highlighted user. The Edit User dialog will appear.
CIMCO PDM User Guide -‐ www.cimco.com
57
The Edit User dialog
Delete
Deletes the highlighted user.
Add
Click this button to add a user. The Append User dialog will appear.
CIMCO PDM User Guide -‐ www.cimco.com
58
The Append User dialog
Fill in the fields as needed.
User Groups
Check the box(-‐es) of the user group(-‐s), the access rights of which you want the highlighted user to have.
User groups are edited under the parent dialog User Groups.
Default Values
Click Default Values to insert the default values in all fields.
OK
Click OK to confirm the values and close the dialog.
CIMCO PDM User Guide -‐ www.cimco.com
59
Database Configuration
In this dialog you define the environment variables for storing and handling the
database and its files.
The Database Configuration dialog
Directories
Main Directory
The start directory for storing the database.
The $ROOT variable will take the value entered here. All other variables for database directories are default defined in relation to the $ROOT variable.
CIMCO PDM User Guide -‐ www.cimco.com
60
Click on the folder icon
Backup Directory
to specify a directory.
This is where backups of the database are placed.
Default value is $ ROOT\BACKUP.
Click on the folder icon to specify a directory.
Temp Directory
The working directory of the database.
Default value is $ROOT\TEMP.
Click on the folder icon to specify a directory.
Real Path
When the cursor is placed in any of the directory variable fields, Real
Path shows which actual path the variable refers to.
Max. Backups
The maximum number of backups you want CIMCO PDM to store in the backup directory.
Options
Delete files in NC-‐Base
Check this box to also delete the NC files in CIMCO NC-‐Base.
Allow Multiple Links for Main Programs
Check this box to allow more than one link for main programs.
Allow Multiple Links for Sub-‐Programs
Check this box to allow more than one link for sub-‐programs.
Default Values
Click Default Values to insert the default values in all the directory fields.
CIMCO PDM User Guide -‐ www.cimco.com
61
OK
Click OK to confirm the Directories values and close the dialog.
Database Server
This is where you set up the database server.
The Database Server dialog
CIMCO PDM User Guide -‐ www.cimco.com
62
Database Server
NC-‐Base Server Name
In this field you enter the name and address of the computer where NC-‐
Base is installed. The server name can be specified either as the IP address or host name.
Note: If the database runs on this computer, you can just enter
'localhost'.
NC-‐Base Server Port
Enter the port used by the NC-‐Base Server.
Note: Normally, this port should not be changed.
CIMCO PDM Server
CIMCO PDM Server
In this field you enter the name and address of the computer where
CIMCO PDM is installed. The server name can be specified either as the IP
address or host name.
Note: If the database runs on this computer, you can just enter
'localhost'.
CIMCO PDM Server Port
Enter the port used by the CIMCO PDM Server.
Note: Normally, this port should not be changed.
CIMCO PDM User Guide -‐ www.cimco.com
63
Show Columns
In this dialog you can add custom columns to the Database Explorer.
The Visible Columns dialog
Database Fields
Field Name
Lists the user-‐defined columns that can be shown in the Database
Explorer, pending right-‐clicking the Database Explorer columns title bar and selecting via check boxes.
New column names are written in the field below and entered using the green
check mark button.
CIMCO PDM User Guide -‐ www.cimco.com
64
OK
Click OK to confirm the values and close the dialog.
CIMCO PDM User Guide -‐ www.cimco.com
65
access, 52 access rights, 52
Activate Trigger, 44
Add, 8 add a user, 56
Add New Machine, 35
Advanced
,
50
Advanced Machine Settings., 50
Allow Multiple Links for Main
Programs, 59
Allow Multiple Links for Sub-‐
Programs, 59
Allowed Extensions, 49
Allowed Groups,
54
Allowed Sub-‐levels, 20
Append User, 56
Application, 18
Applications
,
25
Associated Files
,
44
Auto-Import
,
48
Auto-‐Logoff Time, 13
Available levels, 20
Backup, 9
Backup Directory, 37, 59
CAD/CAM Setting, 13
CAM Files
,
38
CAM Files Directory, 37
Caption, 19
CIMCO PDM Server, 62
Client Configuration,
12
Comment, 51
Configuration,
11
Contents,
2
Copy, 8
Index
Create a Backup Before Delete, 13
Create Backup Before Open, 13
Create Datafile, 26
Create WPD Folder, 52
Customer, 15
Data Directory, 35
Database Configuration,
11
,
58
Database Field, 44
Database Fields
,
21
,
63
Database Preview, 10
Database Server
,
61
Datafile Template, 26
Default Application on Double-‐Click,
25
Default File Action, 24, 39, 42, 47
Default File Name, 24, 39, 42
Default Path, 24, 39, 42, 47
Default Settings,
24
, 39, 42,
Default Template, 23
47
Default Values, 14, 24, 26,
28
, 30,
37, 39, 42, 45, 47
Delay, 49
Delete, 9
Delete After, 52
Delete files in NC-‐Base, 59
Deselect All, 54
Dest. Field, 30
Destination Directory, 26
Dialog Launch Icon, 11
Digits, 23, 39, 41,
47
Directories
,
36
, 58
Directory Memo Data, 45
Directory Other Files, 45
Directory Tool Data, 45
Disable Transfer Limit, 32
CIMCO PDM User Guide -‐ www.cimco.com
66
Edit User, 55
Enable Transfer Limit, 32
End Trigger, 49 environment variables, 58
Explorer, 8, 10
Explorer view, 10
Ext. / Level, 18
Extension, 23, 39, 41
Extensions, 49
External Applications
,
17
Field Configuration,
43
Field Name, 49,
63
File Name,
38
,
41
,
46
,
48
File Name Prefix, 23, 38, 41,
46
File Template,
23
, 39, 41
Find next, 8
Generate, 49
Generate Tool List, 49
Global Search Fields,
15
Group Name, 53
Icon Dynamic, 20
Icon Static, 20
Import
,
48
Import Delay, 49
Increment, 41
Info, 8
Insert after, 43
Installation,
4
Language, 14
Level, 19,
21
,
25
,
27
,
29
, 31
Level Configuration,
19
Level Description, 20
Level Directory, 20
Level File Handling
,
22
Level Search Fields,
16
Level Settings
,
19
Level Specific Applications,
18
Level Sync
,
29
CIMCO PDM User Guide -‐ www.cimco.com
67
Links, 59
Lock, 9
Logoff, 8
Machine, 38,
48
, 50, 51
41
,
43
,
45
,
46
,
Machine Directory, 36
Machine Group, 16
Machines
,
34
Main-‐ and Backup Directories,
36
Main Directory, 58
Max. Backups,
59
Max. Search Results, 13
Memo Data, 45
Memo Template, 45
Menus,
6
Move, 49
Move File, 47
Multiple Links, 59
NC File Lock, 32
NC File Unlock, 32
NC Files
,
40
NC Files Directory, 37
NC-‐Base Server Name, 62
NC-‐Base Server Port, 62
NC-‐Base Status, 32
Next Number, 23, 41
Open Information on Double-‐Click,
13
Open PDM Explorer on Start-‐up, 13
Options,
59
Other Files
,
46
Other Files Directory, 37
Path Relative to Main Directory, 12
PDM Server, 62
PDM Server Port, 62
Port, 62
Predefined Fields
,
27
Preview Picture Size, 14
Program Format
,
43
Program Overview,
6
Real Path, 37, 45, 59
Remember Password, 12
Remove Trigger, 49
Restore, 9
Search Fields
,
15
Search panel, 10
Select All, 54
Send, 9
Send Directory, 52
Send E-‐mail, 32 send emails, 31
Server Port, 62
Show CAM Preview, 13
Show Columns
,
63
Show File Extensions, 13
Show File Type, 13
Source Field, 30
Source Level, 30
Start Trigger, 48
Status, 16, 32
Status Available, 32
Status Configuration
,
Status Following, 32
Status Group, 32
31
Status Name, 32
Steps, 23
Sub-‐levels, 20
Temp Directory, 59
Template, 39, 41
Tool Data, 45
Tool List, 45, 49
Tool List Extensions, 49
Tool List Template, 45
Tool Trigger, 51
toolbars,
6
Transfer
,
51
Transfer Settings, 51
Trigger, 44,
48
, 49, 51
Unlock, 9
Use CIMCO PDM, 52
Use Level Settings, 41
Use Windows Login Name, 13 user access, 52
User Groups
,
52
, 53, 57
User Info,
55
User Rights,
Users, 53,
54
55
Values,
28
,
WPD, 52
30
WPD Folder, 52
CIMCO PDM User Guide -‐ www.cimco.com
68
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement