advertisement
DVD/VCR DECK
Operating Instructions
Model No.
PV-D4753S
Connections and Initial Setup Procedures are on pages 12 to 17.
MULTI FORMAT PLAYBACK
*
Ability to play back may depend on recording conditions.
As an
E
NERGY
S
TAR Partner, Matsushita Electric Corporation of America has determined that this product or product model meets the
E
NERGY
S
TAR guidelines for energy efficiency.
Please read these instructions carefully before attempting to connect, operate or adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
LSQT0675A
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P1-25.p65
1 2003/03/13, 11:32
Important Safeguards and Precautions
FOR YOUR SAFETY, READ AND RETAIN ALL SAFETY
AND OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON THE UNIT
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from a power source indicated on the unit or in this manual. If necessary, have your
Electric Utility Service Company or Video Products
Dealer verify the power source in your home.
2 POLARIZED OR GROUNDING PLUG
As a safety feature, this product comes with either a polarized power cord plug (one blade is wider than the other), or a three-wire grounding type plug.
POLARIZED PLUG CAUTION:
This plug will only fit into an outlet one way. If you cannot fully insert the plug, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not defeat the safety feature by tampering with the plug.
GROUNDING PLUG CAUTION:
This plug will only fit into a three-hole grounding outlet. If necessary, have an electrician install the proper outlet. Do not defeat the safety feature by tampering with the plug.
3 POWER CORD
Make sure power cords are routed so that they are not likely to have anything rest on them, roll over them, or be in the way of walking traffic.
If an extension cord is used, make sure it also has either a polarized or grounded plug and that the cords can be securely connected.
Frayed cords, damaged plugs, and damaged or cracked wire insulation are hazardous and should be replaced by a qualified service technician.
Overloaded outlets and extension cords are fire hazards and should be avoided.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat generated during operation. If they are blocked, heat build-up inside the unit can cause failures that may result in a fire hazard or heat damage to cassettes or discs.
For protection, follow these rules: a. Never cover ventilation slots or the unit while in use, or operate the unit when placed on a bed, sofa, rug, or other soft surface.
b. Avoid built-in installation, such as a book case or rack, unless proper ventilation is provided.
5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS
OR SUDDEN TEMPERATURE CHANGES
Do not place the unit over or near heater or radiator, in direct sunlight, inside closed vehicles, in high temperature [over 104°F (40°C)], or in over
75% humidity. If the unit is suddenly moved from a cold place to a warm one, moisture may condense in the unit and on the tape causing damage. Never subject the unit to vibration, impact, or place it so that the surface is tilted as internal parts may be seriously damaged.
6 TO AVOID PERSONAL INJURY
• Do not place unsecured equipment on a sloping surface.
• Do not place this unit on any support that is not firm, level, and adequately strong.
The unit could fall causing serious injury to a child or adult and damage to the unit.
• An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
• Carefully follow all operating instructions and use the manufacturer's recommended accessories when operating this unit or connecting it to any other equipment.
2
OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION
If an outside antenna or cable system is connected to the equipment, be sure the antenna or cable system is grounded so as to provide some protection against built up static charges and voltage surges.
NEC - NATIONAL
Section 810 of the National Electrical
ELECTRICAL CODE
Code, ANSI/NFPA 70 (in Canada,
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
part 1 of the Canadian Electrical
Code) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS
An outside antenna system should be located well away from power lines, electric light or power circuits and where it will never come into contact with these power sources if it should happen to fall. When installing an outside antenna, extreme care should be taken to avoid touching power lines, circuits or other power sources as this could be fatal. Because of the hazards involved, antenna installation should be left to a professional.
USING THE UNIT
If the unit has been in storage or moved to a new location, refer first to the INSTALLATION section of these safeguards.
1 KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.
2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR
STRONG IMPACT,
unplug the unit and have it inspected by a qualified service technician before use.
3 DURING AN ELECTRICAL STORM
During a lightning storm, whether indoors or outdoors, or before leaving the unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system.
4 WHEN THE UNIT IS PLUGGED IN
• Never expose the unit to rain or water. DO NOT OPERATE if liquid has been spilled into the unit. Immediately unplug the unit, and have it inspected by a service technician.
Fire and shock hazards can result from electrical shorts caused by liquid contact inside.
• Never drop or push any object through openings in the unit.
Some internal parts carry hazardous voltages and contact can cause electric shock or fire hazard.
Do not put any foreign object on the disc tray.
• Avoid placing the unit directly above or below your TV set as this may cause electrical interference. Keep all magnets away from electronic equipment.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards.
6 CLEANING THE UNIT
Unplug the unit. Then, use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into the unit and cause electrical shock. Any substance such as wax, adhesive tape, etc. may mar the cabinet surface.
Exposure to greasy, humid, or dusty areas may adversely affect internal parts.
SERVICE
1 DO NOT SERVICE THIS PRODUCT YOURSELF
If, after carefully following the detailed operating instructions, this product does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug the unit and contact a qualified service technician.
2 IF REPLACEMENT PARTS ARE REQUIRED
Make sure the service technician uses only parts specified by the manufacturer, or those having the same safety characteristics as the original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards.
3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK
After any service or repairs to the unit, request the service technician to conduct a thorough safety check as described in the manufacturer’s service literature to ensure that the unit is in safe operating condition.
D4753S P1-25.p65
2 2003/03/13, 11:32
Safety Precautions/Mesures de sécurité
WARNING:
To prevent fire or shock hazard, do not expose this equipment to rain or moisture.
CAUTION:
To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Avertissement:
Afin de prévenir tout risque d’incendie ou de chocs
électriques, ne pas exposer cet appareil à la pluie ou
à une humidité excessive.
Attention:
Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock.
Therefore, it is dangerous to make any kind of contact with any inside part of this unit.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.
CAUTION:
UNIT IS A CLASS I LASER PRODUCT.
HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD
CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED.
BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.
WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE
YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER
OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
CAUTION:
LASER RADIATION
WHEN OPEN DO NOT
STARE INTO BEAM.
ATTENTION:
RAYONNEMENT
LASER EN CAS
D’OUVERTURE.
NE PAS REGARDER
DANS LE FAISCEAU.
(Inside of product)
FCC NOTE:
This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a residential environment. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver.
If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the booklet, “Something About Interference” available from FCC local regional offices helpful.
FCC Caution:
To assure continued compliance, (example- use only shielded interface cables when connecting to other devices.) Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
FCC Warning:
Any unauthorized changes or modifications to this equipment would void the user’s authority to operate.
Region Management Information:
This DECK is designed and manufactured to respond to the
Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this DECK, this
DECK cannot play this disc.
●
The Region number for this DECK is “1”.
●
The Player will play DVD-Video marked with labels containing “1” or “ALL”.
Example:
1
ALL
1
2
4
3
D4753S P1-25.p65
3 2003/03/13, 11:32
Before Using
Congratulations
on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your DECK.
• Date of Purchase
• Dealer Purchased From
• Dealer Address
• Dealer Phone No.
• Model No.
PV-D4753S
• Serial No.
Accessories
Remote Control
LSSQ0377
Batteries 2 “AA”
RF Coaxial Cable
LSJA0372
To order accessories, call toll free
1-800-332-5368.
Disc formats supported by this DECK
DECK can play back discs bearing any of the following marks:
[Discs Played 8cm (3") or 12cm (5")]
Logo Disc type
DVD (DVD-Video)
DVD-R (DVD-Video formatted discs [finalized])
DVD-Audio
Video CD
CD (CD-DA)
CD-R/CD-RW (CD-DA,Video CD formatted discs [finalized])
WMA, MP3, JPEG
Discs which cannot be played
• DVD with Region No. other than “1” or “ALL”
• PAL discs (the audio on DVD-Audio can be played),
DVD-RAM, DVD-ROM, DVD-RW, DVD+RW, CD-ROM,
CDV, CD-G, CVD, SVCD, SACD, Divx Video Disc and
Photo-CD
Notes
• Do not use irregularly shaped discs (e.g. heartshaped), as these can damage the unit.
• It may not be possible to play CD-R, CD-RW and
DVD-R in all cases due to the type of disc or condition of the recording.
Disc Handling
Handling precautions
• Sticking a label on the disc may impair DVD-R playback.
• Do not attach sticker to discs. (Do not use discs with exposed adhesive from tape or left over peeled-off stickers.)
• Only hold disc by edges as shown below. Fingerprints, dirt and scratches can cause skipping and distortion.
• Do not write on label side of disc.
• Never use record cleaning sprays, benzine, thinner, static electricity prevention liquids, or any other solvent.
Loading the Batteries
4
2) Insert batteries as marked.
Battery replacement caution
• Do not mix old and new batteries.
• Do not mix alkaline with manganese batteries.
1) Open cover.
3) Close cover.
Disc tray
Disc
• Do not try to close disc tray when disc is not properly placed.
To clean disc surface
With a soft, damp (water only) cloth, gently wipe from the center hole to the outer edge as shown below. (Wiping in a circular pattern will scratch the surface.)
If disc is brought from a cold to a warm environment, moisture may form on the disc
Wipe away moisture with a soft, dry, lint-free cloth before using disc. (See above.)
Improper disc storage
Discs could be damaged if stored or left in areas:
• exposed to direct sunlight.
• that are humid or dusty.
• near heat (i.e. heater, radiator, etc.).
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P1-25.p65
4 2003/03/13, 11:32
Table of Contents
DVD / VCR
Important Safeguards and Precautions
............................
2, 3
Before Using
............................................................................
4
DECK & Cassette Information
...........................................
6 , 7
Location of Controls
.......................................................
8 ~ 10
Displays
(On Screen Displays and Multi Function Display) ....................
11
Connections
..................................................................
12 ~ 15
Initial Setup for Basic Connections
(Ready to Play)
..........
16, 17
VCR
Reset Language, Channels, Clock, VCR’s Output Channel
...
18, 19
Playback/ Record on a Tape
...........................................
20, 21
DVD
Basic DVD Operation
......................................................
22, 23
Timer Recording
..............................................................
24, 25
MTS Broadcast/ VHS Hi-Fi Stereo System
....................
26, 27
Multi-Brand Control Feature
...........................................
28, 29
Tape Operation
(Search System)
.......................................
30 ~ 32
Special VCR Features
.....................................................
33, 34
Copying Your Tapes
(Dubbing) .........................................................
35
Disc Operation
...............................................................
36 ~ 41
DVD Operation using On-Screen Displays
.................
42 ~ 44
MP3/WMA/JPEG Playback Operation
..........................
45 ~ 47
DVD Lock Feature
.................................................................
48
Settings for DVD Operation
..........................................
49 ~ 53
Language Code List
..............................................................
54
DVD / VCR
Warning and Instruction Displays
........................................
55
Before Requesting Service
.............................................
56, 57
Limited Warranty
.............................................................
58, 59
Customer Services Directory
...............................................
59
Spanish (Español) Quick Use Guide
.............................
60~ 65
Index
.................................................................................
66, 67
5
D4753S P1-25.p65
5 2003/03/13, 11:32
DECK & Cassette Information
Head Cleaning
Playing older or damaged tapes may eventually cause video heads to become clogged.
Video Head Clog Sensor
During playback, this screen appears if clogging is detected.
To remove screen, press PLAY on the remote or DECK.
V I DEO HEADS MAY
NEED CLEAN I NG
PLEASE I NSERT HEAD
CLEAN I NG CASSETTE
OR REFER TO MANUAL
END : PLAY
• Use “dry” type head cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)
• Follow cleaning tape instructions carefully.
Excessive use of tape can shorten head life.
• If head clog symptoms persist, contact your nearest servicenter by visiting our Web Site
(see p. 59).
Prevent Accidental Tape Erasure
Break off the tab to prevent recording.
Record Tab
Screw driver
To record again
Cover the hole with cellophane tape.
Record/ Playback Time
Only use tapes with the mark in this DECK.
Tape Speed
Setting
SP
(Standard Play)
LP
(Long Play)
SLP
(Super Long Play)
Type of Video Cassette
T60
1 Hour
2 Hours
T120
2 Hours
4 Hours
T160
2 Hours
40 Minutes
5 Hours
20 Minutes
3 Hours 6 Hours 8 Hours
Cleaning DECK
Use a soft cloth or dusting attachment of a vacuum cleaner to remove dust from the ventilation holes on the back sides and bottom of the cabinet. Plastic surfaces are easily scratched and can be marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate more dust. We recommend using a non-abrasive, antistatic cleaner and polisher.
Features for a Quality Picture (VCR)
Digital Auto Picture
Automatically controls the video output signal for less noise depending on the tape condition.
Digital Auto Tracking
Continuously analyzes the signal and adjusts for optimum picture quality.
Manual Tracking Control
(to reduce picture noise)
Use during Playback and Slow Motion mode to reduce picture noise.
Press CH
(TRACKING) / on the remote control or on DECK until the picture clears up.
To return to Auto Tracking,
press POWER
off, then on again a few seconds later.
R
R R
R
R
R
R
R
V-Lock Control (to reduce picture jitter)
In Still mode,
CH
(TRACKING) / operate as a V-Lock control.
6
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P1-25.p65
6 2003/03/13, 11:32
Specifications
Power Source:
Power Consumption:
120 V AC, 60 Hz
Power On: Approx. 32 watts, Power Off: Approx. 4 watts
Video Signal:
EIA Standard NTSC color
Video Recording System:
4 rotary heads helical scanning system
1 track (Normal), 2 channel (Hi-Fi Audio Sound)
Audio Track:
Tuner:
Broadcast Channels:
CABLE Channels:
VHF 2 ~ 13, UHF 14 ~ 69
Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)
Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125
Input/Output Terminal:
Input Terminal:
Output Terminal:
Audio/Video Line Input/Output, RF Input/Output
Audio/Video Line Input (Front)
S-Video Output (DVD only), Component Video Output (DVD only)
Audio Output 2 (L), (R)
Operating Temperature:
Operating Humidity:
Weight:
Dimensions:
5 °C ~ 40 °C (41 °F ~ 104 °F)
10 % ~ 75 %
4.9 k g
(10.8 lbs).
430 (W) x 95.5 (H) x 344 (D) mm
16-15/16” (W) x 3-12/16” (H) x 13-9/16” (D) inch
Discs Played
(1) DVD-Video Disc
DVD-Audio Disc
5” (12 cm) single-sided single-layer
5” (12 cm) single-sided double-layer
5” (12 cm) double-sided double-layer (one layer per side)
3” (8 cm) single-sided single-layer
3” (8 cm) single-sided double-layer
(2) Compact Disc
3” (8 cm) double-sided double-layer (one layer per side)
5” (12 cm) disc
(CD-DA, Video CD)
(CD-R/CD-RW, MP3, WMA, JPEG)
3” (8 cm) disc
Digital Audio Output:
Pickup:
Digital Optical Connector
Wavelength: 655 nm (DVD), 790 nm (Video CD/CD)
Laser power: CLASS II
Note:
•
Designs and specifications are subject to change without notice.
Definition of Terms (DVD)
Angle:
Some DVD discs feature scenes simultaneously shot from different angles.
The ANGLE button can be used to view the scene from different angles.
(ANGLE Indicator lights on DECK when a scene recorded at different angles is detected.)
Chapter Number:
Titles are subdivided into numbered sections. You can quickly search for a favorite scene using these numbers.
DVD:
A high-density optical disc on which high-quality pictures and sound have been digitally recorded. DVD incorporates new video compression technology (MPEG II) and high-density recording technology which allow entire movies to be recorded with incredible playback quality.
Playback Control:
With Video CD (version 2.0), scenes or information may be selected for
Subtitles:
viewing or listening from an interactive menu that appears on the TV screen.
Written dialogue which appears at the bottom of the screen.
Time Number:
The elapsed play time from the start of a disc or title. Use to quickly find scenes. (May not work with some discs.)
Title Number:
For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc.
Track Number:
Numbers assigned to tracks on Video CDs and CDs to allow specific tracks to be quickly located.
Video CD:
CD containing picture and sound with same quality level as video tape.
This DECK also supports Video CDs with playback control (version 2.0).
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093, licensed for limited viewing uses only.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
7
D4753S P1-25.p65
7 2003/03/13, 11:32
Location of Controls
Remote Control
EJECT
/
OPEN / CLOSE
pp. 20
, 22
POWER
VCR mode p. 28
DSS / CABLE mode
p
. 28
PLAY pp. 20
, 22
REWIND
/
SEARCH
/
SLOW
-
pp. 20
, 23
VCR/TV p. 21
NUMBER keys
RETURN /
SEARCH pp
. 22,
30
ACTION pp. 18
, 49
SKIP
SKIP
p
. 23
TITLE
p
. 38
ANGLE
p
. 37
AUDIO (SAP / Hi-Fi) pp. 27
,
36
Bold
:
VCR Function
Italic: DVD Function
Bold Italic
:
VCR and DVD Functions
Normal: Others
DISPLAY p. 11
,
42
TV mode
p
. 28
DVD mode
p
. 28
INPUT p. 35
FAST FORWARD
/
SEARCH
/
SLOW+ pp. 20
, 23
PAUSE
/
STILL pp. 20
, 23
STOP pp. 20
, 22
ADD/DELETE
/ CLEAR
pp. 19,
39, 48
Virtual Surround Sound (V.S.S.) /
ENTER
pp
. 23, 28
PROGRAM p. 24
SELECT
MENU
p
. 38
SET
SUB TITLE
p
. 36
ZOOM
p
. 37
COMMERCIAL SKIP
/
ZERO SEARCH pp. 31, 32
VOLUME
+
/
-
p
. 28
COUNTER
RESET p. 32
SPEED p. 21,
41
/
PAGE
CHANNEL
TRACKING
/
/
V-LOCK pp. 6, 21
TAPE POSITION
/
VOLUME ADJUST
p. 34,
40
RECORD p. 21
EJECT button:
When this button is pressed in VCR mode, the tape is ejected.
This button is inoperative if pressed during recording.
If pressed in DVD mode, the disc tray opens or closes.
8
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P1-25.p65
8 2003/03/13, 11:32
Bold
:
VCR Function
Italic: DVD Function
Bold Italic
:
VCR and DVD Functions
Normal: Others
STOP/EJECT p. 20
FAST FORWARD/SEARCH p. 20
PLAY p. 20
REWIND/SEARCH p. 20
Remote
Sensor
POWER
If the disc cannot be removed...
First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray.
The tray will eject a little. Now, pull the tray all the way out and remove the disc.
Cassette
Over 2 inches
Compartment
Disc Tray OPEN/CLOSE
p.
22
Audio/Video
Input Connector 2
(LINE 2)
p. 35
CHANNEL /
TRACKING/V-LOCK pp. 6, 21
REC p. 21
Multi Function
Display
p.
11
PROGRESSIVE
p.
10
PAUSE
p.
23
SKIP
SKIP
p.
23
PLAY
p.
22
STOP
p.
22
Reset All Memory Functions
Use when moving DECK to new location, or if a mistake was made in the Initial
Setup section (return to Factory Setting).
• Make sure a tape is not inserted in the DECK.
1 2
1
2
3
Turn DECK Power on.
Press and hold both
VCR PLAY
and
CHANNEL
on the DECK for more than 5 seconds.
• The power shuts off.
Do “Initial Setup (Ready to Play)” on page 16.
9
D4753S P1-25.p65
9 2003/03/13, 11:32
Location of Controls (continued)
Rear View of DECK
AC Power Plug
• While plugged into an AC outlet, this DECK consumes 4 W of electrical power in off mode.
Bold
:
VCR Function
Bold Italic
:
VCR and DVD Functions
Italic: DVD Function
VHF/UHF Antenna Output Terminal p.12
VHF/UHF Antenna Input Terminal p. 12
Component Video Output
Connector (Y, P
B
, P
R
) (DVD Only)
p.
13
Video Output
Connector p.
12
Video Input
Connector p. 35
5.1ch Analog Audio Output
Connector (CENTER, SUB WOOFER,
SURROUND L/R, FRONT L/R)
(DVD Only)
p.
15
• •
•
Optical Digital Audio
Output Connector
(DVD Only)
p.
15
S-Video Out
Connector
(DVD Only)
pp.
10, 13
Audio Output 2
Connector (L/R) p.
13
Audio Output 1
Connector (L/R) p.
12
Audio Input
Connector (L/R) p.
35
The following table shows the status of the output jacks when in VCR or DVD mode.
VCR
DVD
Video Output
Audio Out 1
Audio Out 2
YES
YES
Component
Video Output
N/A
YES
S-VIDEO OUT
N/A
Note
• PROG functions on the remote are not available when using Component Video Output and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press
PROG.
To enjoy PROGRESSIVE SCAN video
(1). Connect
Component Video Output to the component video input terminals of a television.
(See p. 13.)
(2). When the PROGRESSIVE button is pressed, the ON lamp lights up (see p. 9) and the
PROGRESSIVE SCAN signal is output from the Component Video Output Connector.
Notes
• The PROGRESSIVE button can be operated when the DECK is in DVD function mode.
• The screen may shift off-center when using progressive output. Please adjust the screen position if this occurs. (Refer to your TV manual.)
• The DECK outputs video signals (not PROGRESSIVE SCAN) from the “VIDEO OUT” and
“S-VIDEO OUT” terminals when the ON lamp is lit.
10
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P1-25.p65
10 2003/03/13, 11:32
Displays (On Screen & Multi Function)
On Screen Displays (VCR)
Function & Channel Displays
CH 0 8
When a function button is pressed, e.g. PLAY, or you change channels, a 5-second display appears.
VCR Status & Clock Displays
To display or remove overlay at right,
➛
press DISPLAY
.
Function Status
Rec Time Remaining
(OTR mode only, see p. 21.)
Broadcast Audio
Being Received
(See p. 26.)
Blank Tape/ No Video Signal
Indications
Whenever a blank section of a tape comes up in Play mode, or when the selected channel has no broadcast signal with Weak Signal Display
Feature (p. 33) set to OFF, the TV screen will turn solid blue.
Current Time Channel
REC 1 2 : 0 0AM
0 : 25
CH 02
-0 : 1 2 : 3 4
SP
STEREO
SAP
MONO
Counter
Tape Speed
(See p. 6.)
Multi Function Display
VCR mode Indicator
Lights up when
DECK is VCR mode.
Tape Indicator
Lights up when a tape is inserted.
DISC Indicator
Lights up when a disc is inserted.
Timer Indicator
Lights up when
DECK is set for
Timer Recording, or when One
Touch Recording
(OTR) is used.
Flashes when
Timer Recording is set, but a tape has not been inserted into DECK and when a power interruption occurs during Timer
Programming.
V C R
TIMER REC
Hi - Fi
VCR REC Indicator
Lights up during recording.
Hi-Fi Indicator
Lights up when
Hi-Fi audio is monitored in Play mode.
C D
DVD
MP3 WMA
ANGLE
AM
PM
AM/PM
Indicator
DTS Indicator
Lights up when DTS formatted DVD is played.
(DVD only)
Dolby Digital
Indicator
Lights up when “Dolby Digital” formatted DVD is played.
(DVD only)
DVD mode Indicator
Lights up when
DECK is DVD mode.
CD/MP3/WMA
Indicator
CD : Lights when a
Video or Audio
CD is inserted or JPEG file is played.
MP3/WMA :
Lights when an
MP3 or WMA file is played.
ANGLE Indicator
Lights up when a scene recorded at different angles is detected.
(See p. 37.)
(DVD only).
Clock/ Status/ Channel/ Speed Display
Displays the current time. Briefly displays DECK status when a function button is pressed. Briefly displays the channel number, or “L1” or “L2” when a channel or line input is selected. Briefly displays the recording speed when SPEED is pressed.
11
D4753S P1-25.p65
11 2003/03/13, 11:32
Connections
Basic Connections
•
•
If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher quality picture and sound.
You can enjoy stereo sound even if your TV is not stereo by connecting a stereo amplifier to DECK.
• Connect DECK and TV with an RF Coaxial Cable
a
(supplied) or an AV Cable
b
(not supplied) as shown in the figure below.
■
DSS Receiver DECK TV
■
DECK TV
Antenna or Cable
■
Cable Box DECK TV
DSS
Receiver
IN
IN
OUT
IN
OUT
Cable Box
DVD/VCR DECK
VIDEO
OUT
L
AUDIO
R
IN 1
IN FROM ANT.
VHF/UHF
OUT TO TV
or
1
Disconnect antenna or cable from TV and connect to DECK.
2
Connect DECK to TV with RF Coaxial Cable.
TV
a
RF COAXIAL CABLE
(supplied)
AUDIO IN
R L
VIDEO
IN
VHF/
UHF
b
AV CABLE
(not supplied)
WARNING
When using “Nut type” RF coaxial cables, tighten with fingers only. Overtightening may damage terminals.
Note to CABLE system installer
This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the
NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
12
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P1-25.p65
12 2003/03/13, 11:32
Other Connections
■
With a Cable Box (DECK Cable Box TV)
DVD/VCR DECK
ANT or CATV
TV
OUT IN 1
IN FROM ANT.
VHF/UHF
OUT TO TV
Cable Box
IN OUT
■
Connect With Two Cable Boxes
DVD/VCR DECK
ANT
IN FROM ANT.
Cable Box
OUT IN 1
or
CATV
IN OUT
2-Way Splitter
OUT 1 OUT 2
Cable Box
IN OUT
VHF/
UHF
IN
R
OUT
AUDIO
L
VIDEO
VHF/UHF
OUT TO TV
A/B Switch
IN 1 IN 2
You Can
• view any
(including scrambled) channel.
• use Remote
Control to select channels without using Multi-brand control feature.
You Cannot
• record scrambled channels.
You Can
TV
IN
R
OUT
AUDIO
L
VIDEO
VHF/
UHF
• record and view both scrambled and unscrambled channels if additional equipment is added.
This connection requires: two converter boxes, an A/B switch, and a 2-way splitter.
You Cannot
• view a channel other than the one selected for any type of recording.
• do a Timer recording of a channel unless you select it on the Cable Box.
Connections For DVD Only (enjoying higher picture quality)
1
2
3
Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT or S-VIDEO mode).
If your TV has COMPONENT VIDEO INPUT, connect to COMPONENT VIDEO OUT.
If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, connect to
S-VIDEO OUT.
When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.
Notes
•
You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV, and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.
• PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT
Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.
• TV must have capability to accept and display a progressive scan signal to use
PROGRESSIVE mode. Consult your TV operating instructions.
DVD/VCR DECK
TV
From DECK’s
A/V OUTPUT
DVD OUTPUT
COMPONENT
VIDEO OUT AUDIO OUT2
IN
IN
IN
Y
Y
AUDIO
PB
P
B
L
VIDEO
S-VIDEO OUT
PR
P
R
R
S-VIDEO
IN
or
13
D4753S P1-25.p65
13 2003/03/13, 11:32
Connections (continued)
Audio Connections
Ready Checklist
Turn down the volume, then turn DECK, as well as other equipment to be connected, off before proceeding with connection.
Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely.
Read through the instructions before connecting other equipment.
Ensure that you observe the color coding when connecting audio and video cables.
■
Connecting Amplifier (2ch stereo system)
DVD/VCR DECK
Speaker
AUDIO OUT2
L
R
Amplifier
AUDIO IN
R L
Speaker
Enjoying digital audio output from the digital audio output connector
Notes on audio output from the optical digital audio output connector
Disc
Sound recording format
Optical digital audio output from connector
DVD
Video CD
CD
MP3
Dolby Digital
Linear PCM
(48/96/192/44.1/88.2/
176.4 kHz 16/20/24bit)
DTS
MPEG 1
Linear PCM
MP3
Dolby Digital bitstream (1-5.1 ch) or PCM (48 kHz sampling/16 bit only)* 1
Linear PCM (2 ch)
(48 kHz sampling/16 bit or 44.1 kHz sampling/
16 bit)*
2
Bitstream or PCM (48 kHz sampling/16 bit only)* 1
PCM (44.1 kHz sampling)
Linear PCM (44.1 kHz sampling)
Linear PCM (It depends on the MP3 file)
WMA
WMA
Linear PCM (It depends on the WMA file)
*1 The type of audio output from the connector can be selected by the Settings for DVD
Operation. (See p. 50.)
*2 Sound having 96/192 kHz sampling is converted into 48 kHz sampling (or 88.2/176.4 kHz sampling is converted into 44.1 kHz sampling) when it is output from the DECK’s optical digital audio output connector.
For your reference:
• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories
Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.
• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit,
DVDs are recorded in 44.1 kHz/16 bit ~ 192 kHz/24 bit.
Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942, 5,956,674,
5,974,380, 5,978,762 and other world-wide patents issued and pending. “DTS” and “DTS Digital
Surround” are registered trademarks of Digital Theater Systems, Inc. Copyright 1996, 2000
Digital Theater Systems, Inc. All rights reserved.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
14
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P1-25.p65
14 2003/03/13, 11:32
■
Connecting Amplifier (5.1 ch Surround system)
Enjoy the powerful movie theater and hall-like sound available with multiple channel audio found on DVDs by connecting an amplifier and speakers.
There are two types of connection, digital and analog.
A. Digital connection (DECK OPTICAL Digital Audio Output Connector)
When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS bitstream is output from the DECK OPTICAL Digital Audio Output Connector. When DECK is connected to a Dolby Digital decoder or DTS decoder, you can enjoy theater-quality audio in your home. [An optical digital audio cable (optional) is required when an optional
Dolby Digital decoder or DTS decoder is used.]
B. Analog connection (5.1 ch Analog Audio Output Connector)
Connect an amplifier with multi-channel audio input terminals. This DECK can decode
Dolby Digital and DTS. There are no limitations on sampling frequency with this kind of connection.
Notes on connecting an optical digital audio cable
(optional)
• Firmly connect the cable to the connector.
Surround
Speaker
[5.1 ch Surround system]
Surround
Speaker
Center
Speaker
Front
Speaker
Front
Speaker
Amplifier
B. Analog connection
DVD/VCR DECK (Rear)
To multi-channel audio input terminals
Decoder with Dolby Digital
/DTS processing
Subwoofer
A. Digital connection
Optical Digital Audio
Cable (optional)
To Optical Digital Audio
Input Connector
Caution for optical digital audio output connector:
• When connecting an amplifier (with an Optical Digital Input Connector) which does not contain the Dolby Digital or DTS decoder, be sure to select “PCM” at “Dolby Digital” and “PCM” at “dts” of the Settings for DVD Operation “Audio Output” (see p. 50).
Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be harmful to your ears and damage your speakers.
• When a Dolby Digital/DTS decoder is connected, please select “Bitstream” at “dts” or
“Dolby Digital” of the Settings for DVD Operation “Audio Output”.
If “PCM” is selected, there will be stereo sound. (See p. 50.)
• Video CDs and CDs can be played as usual.
Note:
• Some DTS decoders which do not support DVD-DTS interface may not work properly with
DECK.
15
D4753S P1-25.p65
15 2003/03/13, 11:32
Initial Setup for Basic Connections (Ready to Play)
Before doing Initial Setup
1
2
3
Turn TV on
.
See connections a
RF Coaxial Cable Connection and b AV Cable Connection on page 12.
<RF Coaxial Cable Connection>
Set
TV
to
channel 3.
<AV Cable Connection>
Set
TV
to
VIDEO.
[DECK
➛
TV]
• Go to “Initial Setup (Ready to Play).” (See below.)
[Cable Box
➛
DECK
➛
TV], [DSS
➛
DECK
➛
TV]
• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel in your time zone.
• If you use a DSS Receiver, it must be turned off.
Initial Setup (Ready to Play)
1
2
Press VCR on remote for VCR mode.
Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel and clock set starts.
• If screen below does not appear, check DECK - TV connection and, if TV is tuned to channel 3, try switching it to channel 4.
• To change VCR’s output channel, please refer to “VCR’s Output Channel” on page 19.
Plugging the AC Power Plug into an AC outlet.
CH AUTO SET PROCEEDING
CANCEL : STOP
Notes
• Function buttons are inoperative during Initial Setup.
• To remove a cassette during Auto Set, press EJECT on the remote or STOP/EJECT twice on the DECK.
In this case, settings must be made manually. (See p. 18.)
• Depending on conditions, Auto Clock Set may take longer than 30 minutes. If so, press STOP to stop setup and perform settings manually. (See p. 18.)
AUTO CLOCK SET
PROCEEDING
16
D4753S P1-25.p65
CANCEL : STOP
Continued on next page...
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
16 2003/03/13, 11:32
dy to Play)
D4753S P1-25.p65
*
Important:
If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.
STOP
EJECT
VCR
3 Settings are made automatically.
When setup is done, this screen appears.
6 / 8/ 20 03 SUN 2 : 20PM
DST : ON
SETT I NG : CH 10
AUTO CLOCK SET
COMPLETED
If “AUTO CLOCK SET IS INCOMPLETE” appears, manually set clock. See below.
ACTION
SELECT
SET
AUTO CLOCK SET IS
I NCOMPLETE
PLEASE SET CLOCK BY
PRESSING ACT I ON KEY
Manual Clock Set
If Auto Clock Set was incomplete.
1 Press ACTION* on remote to display
CLOCK screen.
SET CLOCK
1 / /
:
DST : ON
- - - - - - - - -- - - - - - - -- - - - - -
SELE CT MONTH
SELECT :
SET :SET
EXIT : ACT I ON
2
Press to select the month and SET to set. In the same manner, select and set the date, year, time, and DST (Daylight Saving
Time).
SET CLOCK
6 / 8 / 2003 SUN 2: 2 0 PM
DST : ON
- - - - - - - - -- - - - - - - -- - - - - -
SET COMPLETED
SET : SET BACK :
START : ACT I ON
3
Press ACTION to start clock and exit.
17
17 2003/03/13, 11:32
Reset Language, Channels, Clock, VCR’s O
1
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
Press ACTION*
to display MENU.
• PROGRAM functions are not available when using COMPONENT Video Output and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROGRAM.
EXIT : ACTION
2
Language
1)
Press
to select language item.
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
Channels
1)
Press
to select
“SET UP CHANNEL,” and
press SET
.
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
EXIT : ACTION
2)
Press SET
repeatedly to change language item as shown below.
MENU
PREPARAR VCR
FIJAR RELOJ
FIJAR CANAL
LANGUE/LANGUAGE:ESPAÑOL
CANAL DE SALIDA : 3
FIJAR : SET
SALIR : ACTION
For Spanish
MENU
REGLAGE MAGNETOSCOPE
REGLAGE HORLOGE
REGLAGE CANAL
LANGUAGE/IDIOMA:FRANÇAIS
CA SORTIE : 3
EXIT : ACTION
2)
Press
to select
“ANTENNA,” then
press SET
to set your antenna system
(“TV” or “CABLE.”)
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
WEAK S I GNAL D I SPLAY : OFF
CABLE / DSS BOX SET UP
VCR Plus+ CH SET UP
SELECT : SET : SET
EXIT : ACT I ON
3)
Press
to select
“AUTO SET,” then
press SET
.
• If you use a Cable Box, set it to the PBS channel in your time zone.
QUITTER : ACTION
For French
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
SELECT :
EXIT : ACTION
SET:SET
For English
3)
Press ACTION
to exit.
CH AUTO SET PROCEEDING
CANCEL : STOP
• After Channel Auto Set is finished, Auto Clock
Set will be performed.
Clock
1)
Press
to select
“SET CLOCK,” and
press SET
.
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
EXIT : ACTION
2)
Press
to select
“MANUAL,” and
press SET
.
(For Auto Clock Set, select
“AUTO CLOCK SET.”)
SET CLOCK
AUTO CLOCK SET
NUAL
T I ME ZONE ADJUST : 0
SELECT : SET : SET
EXIT : ACT I ON
(“TIME ZONE ADJUST” appears only when auto clock is set.)
SET CLOCK
6 / 8 / 2003 SUN 12: 0 0 PM
DST : ON
- - - - - - - - -- - - - - - - -- - - - - -
SELECT :
SET : SET BACK :
EXIT : ACT I ON
3)
Press
and to select, then set the date, time, and DST (Daylight
Saving Time).
4)
Press ACTION
to start
Clock and exit this mode.
18
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P1-25.p65
18 2003/03/13, 11:32
k, VCR’s Output Channel
*
Important:
If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.
POWER
VCR
Time Zone Adjust
(Only when Auto Clock is set.)
1)
Press
to select
“SET CLOCK,” and
press SET
.
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
SELECT :
EXIT : ACTION
SET : SET
VCR’s Output
Channel
1)
Press
to select
“VCR’S OUTPUT CH.,” and
press SET
.
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
EXIT : ACTION
2)
Press
to select
“TIME ZONE ADJUST,”
2)
Press SET
.
SET CLOCK
I F YOU PRESS ACT I ON
KEY, VCR’ S OUTPUT CH
SW I TCHES TO CH 4.
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
3)
Press ACTION
.
SELECT : SET : SET
EXIT : ACT I ON
PLEASE TUNE YOUR TV TO
CH 4.
and
press SET
to subtract or add hour(s) as necessary.
After 3 seconds
3)
Press ACTION
twice.
• “TIME ZONE ADJUST” returns to “0” if clock is set manually.
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:4
SELECT :
EXIT : ACTION
SET : SET
• To Make Corrections, repeat steps 1) ~ 3).
NUMBER keys
ACTION
ADD/DLT
SELECT
SET
CH /
Add or Delete a Channel
To add channel:
Select channel with
NUMBER keys
and
press ADD/DLT
.
CHANNEL 08 ADDED
To delete channel:
Select channel with
CH /
or
NUMBER keys
and
press ADD/DLT
.
CHANNEL 08 DELE TED
DST (Daylight Saving Time)
DECK auto adjusts clock for DST.
(p. 17.)
Spring (First Sunday in April)
DST:ON
➛
Sets clock ahead one hour.
Autumn (Last Sunday in October)
DST:ON
➛
Turns clock back one hour.
• If your area does not observe
Daylight Saving Time, select
DST:OFF.
• Keep these time changes in mind when programming DECK for timer recordings.
19
D4753S P1-25.p65
19 2003/03/13, 11:32
Playback/ Record on a Tape
Ready Checklist
All connections are made. (pp. 12 ~ 15)
TV and DECK are plugged in.
TV is on and tuned to CH 3, 4, or VIDEO.
Remote is in VCR mode. (Press VCR.)
EJECT
VCR
Playback a Tape
1
Insert a tape.
• DECK power comes on. If Auto VCR/TV (see p. 32) is set to “OFF,” press VCR/TV on the remote to be VCR mode.
REW/SLOW-
VCR/TV
STOP
2
Press PLAY*
to play a tape.
• If tape has no rec. tab (p. 6), auto play begins.
Special Features During Play
Forward/Reverse Scene Search
➛
Press FF/SLOW+
or
REW/SLOW-
.
➛
Press PLAY
to release.
After search has begun, each additional press of
FF
or
REW
changes speed as shown below.
[SLP] : Approx. 21X
↔
Approx. 9X
[LP] : Approx. 9X
↔
Approx. 7X
[SP] : Approx. 7X
↔
Approx. 3X
If at 21X, 9X, or 7X speed the picture is interrupted, change speed to 9X, 7X, or 3X.
Notes
• Picture interruption may occur with some TVs.
• FF and REW search speed may vary depending on current tape position.
Still (Freeze) Picture
➛
Press PAUSE/STILL
.
➛
Press PLAY
to release.
Frame by Frame Picture
➛
Press PAUSE/STILL
in Still mode.
➛
Press PLAY
to release.
Slow Motion Picture
➛
Press FF/SLOW+
(increase speed) or
REW/SLOW-
(decrease speed) in Still
➛ mode.
➛
Press PLAY
to release.
3
Press STOP
to stop a tape.
Press REW/SLOW- or FF/SLOW+
in Stop mode to rewind or fast forward a tape.
Press EJECT
on remote, or
STOP/EJECT
on DECK to eject a tape.
2
Press PLAY.
1
Insert a tape.
DVD
PLAY
FF/SLOW+
PAUSE/
STILL
CH /
REC
SPEED
Notes
• These features work best in SP or SLP mode.
• The sound will be muted.
• To reduce picture noise, see “Manual Tracking
Control” on page 6.
• After DECK is in Still or Slow mode for 3 minutes, it will switch to Stop mode automatically to protect the tape and the video head.
Playback using DECK buttons
Multi Function Display
Press STOP/EJECT to stop and/ or eject a tape.
20
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P1-25.p65
20 2003/03/13, 11:32
*
Important:
If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.
Record on a Tape
2
3
Insert a tape with a record tab
(p. 6).
1
• DECK power comes on. If Auto VCR/TV (see p. 32) is set to “OFF,” press VCR/TV on the remote to be
VCR mode.
This video recorder, equipped with HQ
(High Quality) system, is compatible with existing VHS equipment. Only use tapes with the mark. Only tapes tested and inspected for use in 2, 4, 6, and 8 hour machines are recommended.
Press CH
, or
NUMBER keys
to select the channel.
• For “LINE” input, see p. 35.
• If channel is over 100, press 100 key then press the remaining 2 digits.
Press SPEED
to select the record speed (p. 6).
SP
= Standard Play
LP
= Long Play
SLP
= Super Long Play
• Speed appears on-screen and on Multi Function Display.
Note
Remove loose or peeling labels from tapes to prevent tape jam.
4
Press REC
to start recording.
(The VCR REC indicator lights up on Multi Function
Display),
• To edit out unwanted scenes,
press PAUSE/STILL
to pause, and again to resume recording.
• You cannot view another channel during recording.
5
Press STOP
to stop recording.
One Touch Recording
(recording in progress)
,
➛
press REC
repeatedly to set the recording length
➛
(30 min. ~ 4 hours).
• DECK shuts off after the preset record length.
Record one station, watch another,
➛
press VCR/TV
on the remote
➛
(change to TV mode),
➛ select channels at TV (recording continues).
Select Channels at DECK
(In STOP or
REC. PAUSE mode),
➛
press VCR/TV
on the remote
➛
(change to TV mode),
➛ select channels at DECK.
Play a disc while recording a tape.
➛ insert a disc during recording,
➛
press DVD
, and then
press PLAY
.
Normal Rec 0:30 1:00
4:00
1
Insert a tape.
3:00 2:00
Record using DECK buttons
4
1:30
Press REC to start recording.
Multi Function Display
Notes
•
It is not possible to record from DVD/ Video
CD/ CD to VHS tape using DECK.
• Watching one channel and recording another is not possible when using Cable Box or
DSS Receiver.
• After 5 minutes in Pause mode, DECK stops to protect a tape and video heads.
2
Select
Channel.
Press STOP/EJECT to stop.
21
D4753S P1-25.p65
21 2003/03/13, 11:32
Basic DVD Operation
Ready Checklist
All connections are made. (pp. 12 ~ 15)
DECK is plugged in.
If DECK is connected to an audio amplifier, turn the stereo system’s power on.
POWER
OPEN/
CLOSE
DVD
1
Press POWER
* on the remote or DECK.
2 Press DVD
to select DVD mode.
• If a disc is already inserted, go to step 4.
(Depending on the disc, playback may start automatically.)
3
Press OPEN/CLOSE,
and then place a disc into the disc tray.
• Hold disc by its edges only (p. 4) with printed side up and use guides to place into tray.
1
2
PLAY
REW/
SLOW-
STOP
NUMBER keys
FF/
SLOW+
PAUSE/
STILL
4 Press PLAY
to start playing.
Disc tray closes automatically.
CLOSE
READING
• You may also close tray by
pressing OPEN/CLOSE
.
• Data reading time differs with each disc.
VSS
RETURN
SKIP
SELECT
SET
TITLE
22
SKIP
MENU
10
Operation using DECK buttons
1
Press
POWER.
3, 7
Press
OPEN/CLOSE.
4
Press PLAY.
3
Insert a disc.
6
Press STOP.
*
1
Interactive DVD...
May include multiple camera angles, stories, etc.
* 2 Video CD with playback control...
Particular scenes or information can be interactively selected from a menu that appears on the screen.
If an interactive DVD* 1 or a Video CD with playback control*
2
is used and TITLE
MENU appears, go to step 5.
<Example1>
T I TLE MENU
Dogs Cas t l es
Love r s B i r ds
5
Press
or
NUMBER keys
(see below) to select title, and
press SET
or
PLAY
to start playing.
• “Pressing SET or PLAY” is not necessary when using NUMBER keys.
<Example2>
Using NUMBER keys starts playing automatically.
The number of available titles varies with each disc.
<Input
Example>
1 digit number 1 ••• 1
2 digit number 12 ••• 10 1 2
3 digit number 123 •••100 1 2 3
Press SKIP | or | to go to next or previous menu screen.
• SKIP function not available with all discs.
Please refer to disc jacket for operation information.
To return to menu (play stops)
Press TITLE
,
MENU
, or
RETURN
. (DVD-Video/
DVD-Audio)
Press RETURN
. (Video CD)
6
Press
STOP
to stop playing.
7
Press OPEN/CLOSE
to eject the disc.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P1-25.p65
22 2003/03/13, 11:32
*
Important:
If a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
■
Forward/Reverse Scene Search
Press FF/SLOW+
or
REW/SLOW-
during play.
Press PLAY
to release.
• Starting forward/reverse search during play started from menu on Video CDs may recall menu.
• Search speed, slow at first, increases with each additional press of the button up to 5 levels.
■
Forward/Reverse Chapter/Track Skip
Press SKIP |
or
| SKIP
during play.
Each press skips a chapter (DVD-Video) or track (DVD-Audio/Video CD/CD).
•
Pressing |
SKIP
once midway through a chapter/track returns to the start of that chapter/track. Each additional press skips back one chapter/track.
•
Pressing SKIP |
or
|
during play started from menu on Video CDs may recall menu.
Current playback position
V.S.S.
(Virtual Surround Sound)
Enjoy a surround-like effect if you are using two front speakers only. The effect is broadened and sound seems to come from virtual speakers on either side if the disc has surround signals recorded on it.
Press VSS
in DVD mode.
• The Surround sound effects can be changed by pressing VSS repeatedly as shown by the figure below.
VSS1
VSS OFF
VSS OFF (default) VSS2
VSS3
Note
• Surround sound effects is available in DVD mode only.
• Turn off the surround effects on the other equipment.
• V.S.S. will not work, or will have less effect, with some discs.
• Turn V.S.S. off if it causes distortion.
• Sound will only come from the two front speakers if V.S.S. is on.
Chapter/Track Chapter/Track Chapter/Track Chapter/Track
Reverse Skip Forward Skip
■
Still Picture or Pause
Press
PAUSE/STILL
during play.
Press PLAY
to release.
•
DVD/Video CD :
DECK will enter still picture mode.
•
CD :
DECK will enter pause mode.
■
Frame by Frame Picture
(DVD/Video CD)
Press PAUSE/STILL
in still mode.
Press PLAY
to release.
• Each press advances picture one frame.
• Hold button down for consecutive frame advance.
• Whether pictures are advanced by “FRAME” or
“FIELD” is selected automatically. (See p. 53.)
■
Slow Motion Picture
(DVD/Video CD)
Press FF/SLOW+
or
REW/SLOW-
in still mode.
Press
PLAY
to release.
• Slow motion speed, slow at first, is increased with each additional press of the button up to
5 levels.
• Reverse slow motion is not available for Video CDs.
Resume Function
DECK memorizes the point where STOP is pressed (
STOP
is displayed on screen).
Press PLAY
to resume play from this point.
Pressing STOP
again or opening the tray cancels RESUME, however, RESUME is not canceled when power is turned off and on.
• RESUME works only with discs for which elapsed play time is displayed during play.
Enjoy Video CDs featuring playback control without using menus (Video CDs only)
1. Do steps 1-4 (previous page).
When menu appears,
press STOP
.
2.
Press NUMBER keys
to select desired track (play begins).
• Check disc for track numbers.
• Press “1” to start at beginning of disc.
To Resume Menu use,
Press STOP
and
press PLAY
, then the menu will be displayed.
Now, go to step 5 (previous page).
Auto-Power Off Function
Power turns off after DECK has been in
Stop mode (DVD) for about 5 minutes.
• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.
Notes
• Please read the disc jacket for operation information.
• If a single sided disc is placed in upside down, “THIS TYPE OF DISC CANNOT BE
PLAYED. PLEASE INSERT A DIFFERENT
DISC” is displayed.
• Remove disc and press DECK POWER off when not in use.
• Disc continues to rotate with menu displayed even after play is done.
Press STOP to clear menu display when finished with menu.
23
D4753S P1-25.p65
23 2003/03/13, 11:32
Timer Recording
Ready Checklist
All connections are made. (pp. 12 ~ 15)
TV and DECK are plugged in.
Clock set correctly. (p. 18)
Tape has rec.tab. (p. 6)
Remote is in VCR mode. (Press VCR.)
Sufficient tape remaining for recording time.
1
Press PROG*
to display Program.
2
DATE START STOP CH
13 SUN --:-- --:-- --
TODAY
SLP
- - - - - - - - -- - - - - - - -- - - - - - -
SELECT :
SET : SET
END : PROG
1) To set record DATE, press
to select:
1~31= one time, or
DAILY= MON~ FRI, or
WEEKLY= same time each week and
press SET
.
• See selection order left.
Example
Today
14
13
31 1
SELECT /
Selection Order
12
DAILY
WEEKLY
(SUN)
WEEKLY
(MON)
WEEKLY
(SAT)
2) To set remaining items, press
to select and
press SET
to set START/ STOP times,
CH (channel) or LINE input (p. 35), and tape speed (SP, LP, SLP).
Press PROG
to end programming.
POWER
VCR
ADD/DLT
PROG
SELECT
SET
3
DT START STOP CH SPD
13 10 : 00 P 12 : 00 P 02 SP
-- -- : -- -- : -- -- --
-- -- : -- -- : -- -- --
-- -- : -- -- : -- -- --
CANCEL : ADD / DLT
SELECT 1-8 :
ENTER : SET
EXIT : PROG
To Enter More Programs, press
to select and
press SET
to set an unused program number, and then repeat step 2.
Or
Press PROG
to exit.
VCR mode Indicator
V C R
TIMER REC
Hi - Fi
VCR REC Indicator
TIMER Indicator
<Multi Function Display>
• The “Timer” Indicator lights up on DECK.
• You can do Timer Recording with the power on or off.
• “TIMER REC WILL START SOON”
appears on-screen for 2 minutes before Timer Recording starts. If DECK is in DVD mode, no message appears, but the VCR REC Indicator, the VCR mode indicator and
“REC” will flash on Multi function Display.
24
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P1-25.p65
24 2003/03/13, 11:32
*
Important:
If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.
Review, Replace or Clear Program Contents:
(Recording is not in progress)
1
2
Press PROG
to display Program List.
DT START STOP CH SPD
7 9 : 00A 12 : 00A 08 SP
8 10 : 00P 12 : 00P 02 SP
10 8 : 00P 9 : 00P 10 SP
SU 9 : 00P 10 : 00P L1 LP
CANCEL : ADD / DLT
SELECT 1-8 :
ENTER : SET
EXIT : PROG
Press
to select number and
press SET
to display.
To cancel a Timer
Recording in progress...
Hold down STOP
in VCR mode for a few seconds to cancel the Timer
Recording.
(The “TIMER” Indicator goes out on Multi Function Display.)
• Any future daily or weekly recording will be performed as programmed.
3
To Replace program...
DATE START STOP CH
7 SUN 9:00A 12: 00A 08
TODAY SP
----------------------------------------
SELE CT START DATE
SELECT :
SET : SET BACK :
END : PROG
Repeat Step 2 (p. 24) to set new programs.
or
To Clear program...
Press ADD/DLT.
DT START STOP CH SPD
-- -- : -- -- : -- -- --
8 10 : 00P 12 : 00P 02 SP
10 8 : 00P 9 : 00P 10 SP
SU 9 : 00P 10 : 00P L1 LP
CANCEL : ADD / DLT
SELECT 1-8 :
ENTER : SET
EXIT : PROG
4
Press PROG
to end the programming.
Notes
• If you are using a Cable Box, the VCR’s channel for Timer Recording must be set to the Cable Box input channel and Cable Box must be manually set to the desired channel. Cable Box power must be left on.
•
2 minutes before Timer Recording is performed, “PLEASE PREPARE FOR TIMER
REC” appears and Timer Indicator flashes.
Be sure a cassette with record tab is loaded and DECK is in Stop mode.
• If a power interruption occurs while programming the timer, the timer program(s) may be canceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION” appears on-screen, please re-enter the timer programs.
• If the start time for Timer Recording comes up during recording and playing back,
Timer Recording will not be performed.
Important notes when using DSS Receiver
• When recording programs via DSS Receiver, DSS Receiver must be left on.
• When recording programs via an antenna or cable, DSS Receiver must be turned off.
25
D4753S P1-25.p65
25 2003/03/13, 11:32
MTS Broadcast/ VHS Hi-Fi Stereo System
Connection
Make the Audio/Video Connection as shown on pp. 12 ~ 15.
• You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV.
Receivable Broadcast Types
The following are possible audio broadcast types and onscreen displays.
The signal being received is indicated with an “ ” mark while the selected audio mode is indicated with an arrow.
To display the broadcast signal being received,
➛
press DISPLAY*
.
MTS Stereo and SAP broadcast
Multi-channel Television Sound
Stereo (main language) and
Secondary Audio Program (sub language) broadcasts are being received simultaneously.
Select STEREO or SAP audio mode.
STOP 1 2 : 0 0AM
STEREO
SAP
MONO
CH 02
0 : 0 0 : 0 0
SP
DISPLAY
MTS Stereo broadcast
Multi-channel Television Sound
Stereo broadcast. Select STEREO audio mode.
• If stereo broadcast is weak and display flickers, select MONO audio mode for possible better results.
STOP 1 2 : 0 0AM
STEREO
SAP
MONO
CH 02
0 : 0 0 : 0 0
SP
AUDIO
(SAP/Hi-Fi)
SAP broadcast
Secondary Audio Program (sub language) broadcast. Select SAP audio mode for the sub language.
STOP 1 2 : 0 0AM
STEREO
SAP
MONO
CH 02
0 : 0 0 : 0 0
SP
MONO broadcast
Normal monaural sound broadcast.
STOP 1 2 : 0 0AM
STEREO
SAP
MONO
CH 02
0 : 0 0 : 0 0
SP
Equipped with
®
-TV
Noise Reduction for true MTS reproduction.
®
-TV Noise
Reduction is required for good stereo separation and audio fidelity.
®
is a registered trademark, and is licensed by
®
Technology Licensing.
26
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P26-35.p65
26 2003/03/13, 11:32
*
Important:
If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.
Audio Mode for Recording
1
Press AUDIO (SAP/Hi-Fi)
to display audio mode.
(Display disappears after 5 seconds.)
2
STEREO
SAP
MONO
Press AUDIO (SAP/Hi-Fi)
repeatedly to select desired mode.
• Refer to “Receivable Broadcast Types” on p. 26.
• Arrow indicates selection.
3
Make a recording.
See p. 21.
Audio Mode for Playback
1
Start playback.
See p. 20.
2 Press AUDIO (SAP/Hi-Fi)
to display audio mode.
3
H I F I : L / R
H I F I : L
H I F I : R
NORMAL
Press AUDIO (SAP/Hi-Fi)
repeatedly to select desired mode.
• Select “HIFI (L/R)” or “HIFI (L)” or “HIFI (R)” to listen to stereo recordings in stereo sound.
Select “NORMAL” for monaural sound.
• Display disappears after 5 seconds.
• Arrow indicates selection.
Notes
• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard stereo tapes will playback in monaural sound.
• To listen to Hi-Fi stereo playback
,
the DECK AUDIO (L/R) jacks must be connected to a stereo TV or an external stereo amplifier and speakers. (See pp. 12, 14.)
• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
• Hi-Fi and normal audio playback volume level may differ.
27
D4753S P26-35.p65
27 2003/03/13, 11:32
Multi-Brand Control Feature
Multi-Brand Control Setup
The Remote Control can be set to control some TV and
Cable Box/DSS functions.
1
Find your TV and Cable Box/DSS Receiver
Brand Code Number on the following page.
2
Set up for TV control,
➛
hold down TV button
,
➛
enter code with NUMBER keys
.
Set up for Cable or DSS control,
➛
hold down DSS/CABLE button
,
➛
enter code with NUMBER keys
.
• If code number is 100 or greater,
➛ e.g., press 1 - 0 - 2 for 102.
3
Confirm code entry,
➛
press POWER
to turn selected unit on or off.
• See table below for controllable functions in each mode.
Notes
• Repeat setup after remote battery replacement.
• Remote will not control every TV, Cable Box, or
DSS made by the manufacturer listed. If you get no response, your particular unit cannot be controlled. There are NO additional codes for the products listed. If your product is not listed, then the remote is not compatible with that product.
POWER
VCR
DSS/
CABLE
TV
DVD
NUMBER keys
ENTER
Using Multi-Brand Control
After remote is set up, you can select VCR, DVD, TV, or
DSS/CABLE for the desired function.
Press VCR,
DVD, TV, or DSS/CABLE
on the remote.
(Table below shows available remote buttons for each mode.)
Mode
Unit
DVD/VCR TV
DVD/VCR
All VOL
+
/
-
CABLE/ DSS
TV
CABLE/
DSS
EJECT
/ OPEN/CLOSE
*
,
DISPLAY
,
PLAY
,
STOP
,
FF/SLOW+
,
REW/SLOW-
,
VCR/TV
,
PAUSE /STILL
, SKIP,
AUDIO
,
CM/ZERO
,
TAPE POSITION
,
COUNTER RESET, SPEED,
REC
, PAGE
POWER, INPUT,
NUMBER keys,
ENTER,
CH / ,
VOL
+
/
-
VOL
+
/
-
POWER, ENTER,
NUMBER keys
(except 100key),
CH /
*
Bold: VCR Function
Italic: DVD Function
Bold Italic: VCR and DVD Functions
Normal: TV, Cable Box or DSS Receiver
Notes
• Not all functions listed may be controllable.
• In TV or DSS/CABLE mode, it may be necessary to press ENTER after pressing
NUMBER keys for channel selection.
28
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P26-35.p65
28 2003/03/13, 11:32
TV Brand Code Numbers
Panasonic ....................... 01, 02
Quasar ............................ 01, 02
RCA ....................................... 03
GE ......................................... 03
Zenith .................................... 04
Magnavox .............................. 05
Sylvania ................................ 05
Sharp ............................... 06, 07
Sony ...................................... 08
Toshiba ................................. 09
Sanyo .................................... 10
Fisher .................................... 10
JVC ........................................ 11
Hitachi ................................... 12
Mitsubishi ........................ 07, 13
Samsung ............................... 14
Gold Star ................... 15, 16, 17
Cable Box Brand Code Numbers
Archer ......................... 44, 06, 01, 120, 05, 63, 126
Cableview ................ 29, 09, 01, 63, 120, 44, 42, 30
52, 04, 124, 126
Citizen ................... 44, 52, 30, 63, 42, 04, 124, 126
Curtis ..................................... 08, 09, 25, 61, 53, 87
Century ...................................... 44, 51, 75, 59, 126
Cabletenna .................. 29, 09, 01, 63, 120, 44, 126
Cable Cinema .............. 29, 09, 01, 63, 120, 44, 126
Diamond ...................... 29, 09, 01, 63, 120, 44, 126
Eagle ....................... 62, 40, 22, 13, 58, 20, 26, 107
Eastern ................................................... 28, 29, 130
Explorer .................................. 08, 09, 25, 61, 53, 87
Gemini ..................................................... 30, 04, 124
General Electric ...................................... 01, 57, 120
General Instruments . 01, 84, 83, 34, 03, 02, 04, 55
65, 66, 67, 68, 120, 106, 121, 122, 115, 117, 118, 124
Gerrard ............................................... 44, 51, 75, 59
GC Electronics ............... 44, 42, 63, 29, 30, 52, 04
124, 126
Hamlin ............... 41, 14, 15, 28, 102, 104, 103, 130
Hitachi ................................................................... 31
Jerrold .......... 01, 84, 83, 34, 03, 02, 04, 55, 65, 66
67, 68, 120, 106, 121, 122, 115, 117, 118, 124
Jasco ...................................................... 30, 04, 124
Macom ................................................................... 31
Magnavox ...................................................... 26, 112
Matsushita ................................. 17, 16, 08, 87, 109
Movietime ...................... 32, 39, 42, 44, 126, 38, 40
Maestro ........................................................... 74, 35
NEC .................................................... 40, 19, 38, 32
NSC .................................................... 40, 19, 38, 32
Novavision ............................. 08, 09, 25, 61, 53, 87
Next Level ........... 01, 84, 83, 34, 03, 02, 04, 55, 65
66, 67, 68, 120, 106, 121, 122
Oak ................................................. 46, 11, 129, 101
Oak Sigma ..................................... 46, 11, 129, 101
Panasonic .................................. 17, 16, 08, 87, 109
Philips ................... 23, 24, 20, 13, 07, 50, 128, 129
Pioneer ...................................................... 06, 05, 12
Pulsar .................... 04, 42, 63, 44, 30, 52, 124, 126
Quest ........................................................ 06, 05, 12
Radio Shack ............................... 44, 51, 75, 59, 126
RCA ............................................ 17, 16, 08, 87, 109
Realistic ..................................... 44, 51, 75, 59, 126
Recoton ...................................... 44, 51, 75, 59, 126
Regal ................. 41, 14, 15, 28, 102, 104, 103, 130
Regency .................................................. 28, 29, 130
Rembrandt ....... 44, 42, 63, 29, 01, 32, 39, 120, 126
Samsung ...................................... 42, 06, 32, 05, 40
Scientific Atlanta ................... 08, 09, 25, 61, 53, 87
Sheritech ............................................................... 27
Signal ............................................................ 26, 112
SL Marx ............. 42, 06, 32, 40, 43, 44, 52, 63, 126
Sprucer ...................................... 17, 16, 08, 87, 109
Standard Components ............... 32, 39, 42, 44, 126
Stargate .............. 04, 42, 32, 40, 63, 44, 30, 52, 06
124, 126
Sylvania .......................................................... 19, 18
Teknika ........................................................... 74, 35
Telecaption .................................................... 77, 127
Teleview ................................. 40, 19, 38, 32, 42, 06
Texscan .......................................................... 19, 18
Tocom ................................... 34, 33, 01, 42, 66, 120
Toshiba ................................................................. 36
Unika ........................... 44, 42, 63, 29, 01, 126, 120
Universal .............................. 52, 43, 44, 63, 42, 126
Viewstar .................. 62, 40, 22, 13, 58, 20, 26, 107
Videoway .......................................... 07, 23, 50, 129
Vidtek .................................................................... 64
Zenith ............................................... 07, 23, 50, 129
DSS Brand Code Numbers
Toshiba ....................................................... 90
Hitachi/ Hughes .................................... 91, 99
Primestar .................................................... 92
Drake .......................................................... 93
Magnavox ............................................. 94, 95
Uniden ................................................... 94, 95
Optimus ................................................ 94, 95
Panasonic ................................................... 96
ProScan ...................................................... 97
RCA ............................................................. 97
SONY .................................................. 98, 105
Important Notes
• Some manufacturers use several codes for one brand. If the first code entered fails, try the next one listed.
• Some TV, Cable Box and DSS Receiver brands require you to turn on the power manually.
29
D4753S P26-35.p65
29 2003/03/13, 11:32
Tape Operation
Search System
For each recording, an invisible index mark is placed on the tape. A program index and information are also included for timer recordings. These marks are used to access or scan recordings.
Index Search Program End Search
1
2
INDEX SEARCH
ENTER INDEX NUMBER :1
USING 1- 9 KEYS
FORWARD SEARCH :FF
REVERSE SEARCH :REW
NEXT :SEARCH
EXIT :STOP
INDEX SEARCH
FORWARD SEARCH : FF
REVERSE SEARCH : REW
Press SEARCH*
to display SEARCH in Stop or Play mode, and then
press NUMBER keys
to select recording number.
• To calculate number, see below.
Press FF/SLOW+
or
REW/SLOW-
on the remote to start search.
Play begins at search end.
To search forward or back 1 index,
press FF/SLOW+
or
REW/SLOW-
on the remote while screen left is displayed (10 sec.).
• To cancel,
press
PLAY
or
STOP
.
Locates end point of recording for continuity.
1 Press SEARCH
twice to display SEARCH in Stop or Play mode.
2
SEARCH START : FF
EXIT :SEARCH
Examples of
Program End Search
.
Fig. 1
Program 1 the current tape position
Press SEARCH button
FF
Program 2 or BLANK
End Point
Fig. 2
PROGRAM END SEARCH
Press FF/SLOW+
on the remote to start PROGRAM
END SEARCH.
• To cancel,
press
PLAY
or
STOP
.
Program 1 BLANK the current tape position
Press SEARCH button
FF
Program 2 BLANK
End Point
To Calculate Index Number
Example 1:
To go to rec. 2 from rec. 4, enter 3 and press REW.
Fig. 3
the current tape position
Press SEARCH button
Program 1 BLANK
End Point
FF
Program 2
If search exceeds a few seconds in
BLANK area.
1 2 3 4 5 6 7
Example 2:
To go to rec. 6 from rec. 2, enter 4 and press FF.
Upon locating end point,
➛ search continues 7 sec. past end point,
➛ tape rewinds to 10 sec. before end point,
➛ tape plays to end point and stops.
1 2 3 4 5 6 7
NOTE: indicates start points of each recording.
Note
Note
• If Index Search is started very close to an index mark, that index mark may not be counted in the search.
30
• If Program End Search is started very close to an index mark, that mark may be skipped over.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P26-35.p65
30 2003/03/13, 11:32
D4753S P26-35.p65
*
Important:
If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.
Auto Operation Functions
Auto Play
Insert a tape
➛
Power comes on,
➛
Play starts if there is no record tab
(see p. 6).
Auto Rewind
Play
Fast Forward
➛
Tape end
➛
Rewind
Play Auto Eject
(Repeat Play must be off)
Play
➛
Tape end
➛
Rewind
➛
Tape ejects if set some programs
REW/SLOW-
PLAY
FF/SLOW+
STOP
NUMBER keys
SEARCH
CM/ZERO
Commercial Skip
VCR fast forwards (skips) over 1~3 minutes of recorded tape.
1
Press CM/ZERO
in Play mode.
• The skip time can be changed by pressing CM/ZERO repeatedly as shown by the figure below.
PLAY
1st Press
2nd Press
3rd Press
1 min Skip
2 min Skip
3 min Skip
• No indication appears on-screen.
31
31 2003/03/13, 11:32
Tape Operation (continued)
Set to playback a recording over and over.
1
2
Repeat Play
Press ACTION*
to display MENU.
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
EXIT : ACTION
Press
to select “SET UP VCR,” and
press SET
.
The VCR/TV selection can be set to auto or manual.
1
Press ACTION
to display MENU.
2
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
Press
to select
“SET UP
VCR,” and
press SET
.
EXIT : ACTION
3
SET UP VCR
REPEAT
: OFF
REMOTE WARN I NG : ON
AUTO SHUT-OFF : OFF
AUTO VCR/TV : OFF
Press
to select “REPEAT PLAY,” and
press SET
to set “ON” or “OFF.”
SELECT : SET: SET
END : ACT I ON
• Play repeats at tape end or if unrecorded portion over 30 sec. is detected.
4 Press ACTION
twice to return to normal screen.
Note
• For repeat play in DVD mode, see page 44.
3
SET UP VCR
REPEAT PLAY : OFF
REMOTE WARN I NG : ON
AUTO SHUT-OFF : OFF
AUTO VCR/TV : OFF
SELECT : SET: SET
END : ACT I ON
Press
to select
“
AUTO VCR/
TV
,” and
press SET
to set “ON” or “OFF.”
• OFF(Manual): You select “VCR” or
“TV” mode using the
VCR/TV button on the remote.
• ON(Auto): “VCR” mode is automatically set when
VCR is turned on, or in
Play mode.
Zero Search
To quickly return to a specified tape location.
1
Press DISPLAY
during play to display Counter.
2
PLAY 1 2 : 0 0AM
0 : 0 0 : 0 0
SP
Press COUNTER RESET
at desired position to reset to “0:00:00”.
3
Continue to record, playback etc
.
4
Press STOP.
5
REW 1 2 : 3 0AM CH 02
0 : 30 : 30
SP
Press CM/ZERO
in Stop mode to start Zero Search.
4 Press ACTION
to return to normal screen.
Note
• For more on VCR/TV selection, see
“Record one station, watch another” and “Select channels at DECK” sections (see p. 21).
STOP 1 2 : 3 1AM CH 02
0 : 0 0 : 0 0
SP
32
• DECK will go into FF or REW mode and stop at the last point the Counter was set to 0:00:00.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P26-35.p65
32 2003/03/13, 11:32
Special VCR Features
*
Important:
If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.
DISPLAY
STOP
Weak Signal Display Feature
When “ON,” picture is displayed regardless of signal strength.
1
Press ACTION
to display MENU.
2
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
Press
to select “SET UP
CHANNEL,” and
press SET.
SET : SET
EXIT : ACTION
ACTION
VCR LOCK ACT I VATED
SELECT
SET
CM/ZERO
COUNTER
RESET
VCR Lock Feature
When set to ON, all operations except for timer record and tape eject are prohibited. Useful for households with small children.
To turn on, hold down REC
on
DECK in Stop mode with no tape inserted for 7 seconds.
(Please ignore “NO CASSETTE” warning.)
3
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
WEAK S I GNAL D I SPLAY:OFF
SELECT : SET: SET
EXIT : ACT I ON
Press
to select “WEAK SIGNAL
DISPLAY,” and
press SET
to set “ON” or “OFF.”
• ON: Picture is displayed regardless of signal condition, and may not always be clearly visible.
OFF: Screen turns solid blue when signal is weak or non-existent.
• Selecting ON has no effect on connected equipment with blue back feature.
4 Press ACTION
twice to return to normal screen.
Auto Shut-Off Feature
The power shuts off at a preset time.
1
Press ACTION
to display MENU.
2
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
Press
to select “SET UP VCR,” and
press SET.
To turn off,
repeat above.
VCR LOCK OFF
• VCR Lock cancels in 24 hours if clock is set.
REC
EXIT : ACTION
3
SET UP VCR
REPEAT PLAY : OFF
REMOTE WARN I NG : ON
AUTO SHUT-OFF : OFF
AUTO VCR/TV : OFF
SELECT : SET: SET
EXIT : ACT I ON
Press
to select “AUTO SHUT-OFF.”
Press SET
repeatedly to change shutoff time as shown below.
2 Hours
OFF
4 Hours
6 Hours
4
Press ACTION
twice to return to normal screen.
Note
• The shut-off countdown will not function during Play or
Record.
33
D4753S P26-35.p65
33 2003/03/13, 11:32
Special VCR Features (continued)
Remote Warning Feature
If Multi-brand feature is used (p. 28), and this feature is set to on, a warning appears whenever an invalid key is pressed in TV, DSS or CABLE mode.
*
Important:
If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.
1
Press ACTION*
to display MENU.
INPUT
2
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
SELECT :
EXIT : ACTION
SET : SET
Press
to select “SET UP VCR,” and
press SET
.
STOP
PAUSE/
STILL
3
SET UP VCR
REPEAT PLAY : OFF
REMOTE WARN I NG
: ON
AUTO SHUT-OFF : OFF
AUTO VCR/TV : OFF
SELECT : SET: SET
EXIT : ACT I ON
Press
to select
“REMOTE WARNING,” and
press SET
to set “ON” or “OFF.”
• If “OFF,” remote warning will not appear when invalid key is pressed.
4
Press ACTION
twice to return to normal screen.
ACTION
SELECT
SET
TAPE
POSITION
REC
Tape Position and Tape Status Feature
To find out the present tape position and amount of tape remaining.
Tape position is displayed for VHS-C type Cassettes, tapes under 30 minute long, and some other tapes, but the position is not correct.
1 Press TAPE POSITION
to detect current tape position.
DETECTING TAPE POSITION
SP
R 120 M I N.
• “DETECTING TAPE POSITION” is displayed only when a cassette is first inserted, and it takes several seconds for correct tape position to appear.
• The present tape position indication and amount of tape remaining (according to tape speed) is displayed.
• Tape remaining time display may not be precise.
BEG I N END
2
Press TAPE POSITION
to return to normal screen.
Note
This function cannot display exact amount of tape remaining for tapes 30 minutes or less, or for tapes over 120 minutes in length.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
34
D4753S P26-35.p65
34 2003/03/13, 11:32
Copying Your Tapes (Dubbing)
Connection
VCR/ Camcorder
(Hi-Fi)
VIDEO
L
AUDIO
R
OUT
DVD/VCR DECK
IN 1
IN FROM ANT.
VIDEO
AUDIO1
L
R
OUT
VHF/UHF
OUT TO TV
TV
VHF/
UHF
Front of DECK
VIDEO IN 2 L-AUDIO IN2-R
(Audio/Video In Terminals on the front of DECK are available)
1
2
Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK.
To monitor the dubbing, also connect TV as shown.
Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R”
AUDIO IN terminals on DECK.
In place of Playing VCR, you can use other equipment, such as a Camcorder.
Simply connect the unit’s Audio/Video outputs to DECK.
Playing (Source) VCR
1
Insert a pre-recorded tape.
2
Recording (Editing) DECK
Insert a blank tape with record tab.
Press INPUT
to set DECK Input mode to
LINE for Video Input.
(See “Selecting the Input Mode” below.)
3
4
5
Press STOP
to stop dubbing.
To Monitor Dubbing on TV
1
Turn TV on and tune to the Recording
VCR channel (CH 3 or CH 4).
2
If Auto VCR/TV (see p. 32) is set to
“OFF,” press VCR/TV on the remote to be VCR mode.
Note
Press PLAY
, then
PAUSE/STILL
immediately to enter PLAY/PAUSE mode.
Press REC
, then
PAUSE/STILL
immediately to enter REC/PAUSE mode.
The operation of steps 4 and 5 must be done on the playing and recording VCRs at the same time.
Press PLAY
to start dubbing.
Playing VCR starts playback.
Press PAUSE/STILL
to start dubbing.
DECK starts recording.
• Dubbing tapes protected with Copy
Guard will result in poor quality recordings.
Press STOP
to stop dubbing.
Selecting the Input Mode
Method 1:
Press INPUT
repeatedly.
Channel Number
↔
LINE1
↔
LINE2
Method 2:
Press CH
/ .
Display will change as below.
1 2 3
Press
LINE2 LINE1
(CABLE)
125 or
(TV)
69
Press
• “L1” or “L2” lights up on Multi Function Display
(about 4 seconds) when LINE1 or LINE2 is selected.
• LINE1: For rear audio/video connection.
LINE2: For front audio/video connection.
Caution:
• Unauthorized exchanging and/or copying of copyrighted recordings may be copyright infringement.
• Please note that some tapes cannot be dubbed on DECK. Also, it is not possible to dub DVD/ Video CD/ CD to VHS tapes using DECK.
35
D4753S P26-35.p65
35 2003/03/13, 11:32
Disc Operation
Subtitle Language (DVD-Video only)
You can select a different subtitle language (if offered) than the one set at the Settings for DVD Operation.
(See p. 49.)
Ready Checklist
Please read “Basic DVD Operation” on p age
22.
1
Press SUB TITLE*
in Play mode to display the subtitle selection on-screen.
• Display disappears after
5 seconds.
• When no subtitles are offered,
“-” will be displayed instead of the language number.
[Subtitle language]
[Audio sound track language]
ENG
FRA
DEU
ITA
ESP
NLD
English
French
German
Italian
Spanish
Dutch
2
Te amo
Press
to select a language.
Press
to select “ON” or “OFF.”
SVE
NOR
DAN
POR
RUS
JPN
Swedish
Norwegian
Danish
Portuguese
Russian
Japanese
Subtitle language being played back (see chart, right).
Notes
• If after several presses of the button the language does not change, language selection is not offered on the disc.
• When disc is removed, subtitles revert to initial setting language. If the initial language is not recorded on the disc, the disc’s priority language will appear.
Audio Soundtrack Language (DVD only)
You can change the audio soundtrack language, selected at the Settings for DVD Operation, to a different language if available. (See p. 49.)
(This operation works only with discs on which multiple audio soundtrack languages are recorded.)
1
AUD I O : 1 ENG
D o l b y D i g i t a l 3 / 2 . 1 c h
Hello
SELECT :
END
Press AUDIO
in Play mode to display the audio selection on-screen.
• Display disappears after
5 seconds.
Audio attribute 1 type, sampling frequency, bit No. of the disc or number of speaker channel.
CHI
KOR
MAL
Chinese
Korean
Malay
VIE
THA
∗
Vietnamese
Thai
Other
• Change the No. by
pressing
and
press SET
.
,
[Audio attribute 1 type, sampling frequency, bit No. of the disc
(see p. 50.)
]
LPCM
Dolby Digital
DTS
44.1 kHz
192 kHz
16 bit
20 bit
24 bit
1 ch - 5.1 ch
1 ch - 5.1 ch
Linear PCM disc
Dolby Digital disc
DTS disc
2
36
AUD I O : 3 ESP
D o l b y D i g i t a l 3 / 2 . 1 c h
Hola
SELECT :
END
Press
to select desired language.
Notes
• If, after several presses of the
AUDIO button the language does not change, language selection is not offered on the disc.
• When disc is removed, language reverts to initial setting. If this language is not recorded on the disc, the language recorded will be heard.
Audio soundtrack language being played back (see chart, above right).
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P36-60.p65
36 2003/03/13, 11:32
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.
ANGLE Indicator
Multiple Angle Viewing (DVD only)
DVDs may contain scenes shot from multiple camera angles allowing the same scene to be viewed at different angles. You can view these angles, if available, using the
ANGLE button.
1
Press
ANGLE
in Play mode to display the angle selection on-screen.
• Display disappears after
5 seconds.
SELECT :
Notes
• The ANGLE Indicator lights up on
DECK when a scene recorded at different angles is detected.
• The angle number can be set beforehand so that the angle is switched whenever the ANGLE
Indicator lights up.
2
Press
to select the desired angle.
SELECT :
Number of angle being played back.
Vocal Selection for Karaoke Discs
(DVD/Video CD)
1
Press
AUDIO
in Play mode to display the audio screen.
2
Press
(or ) to select as shown below, and
press
(or ) to set.
(DVD only)
SELECT :
END : AUDIO
SET
SELECT
• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF
• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF
• Video CD LR L R
SUB TITLE
ZOOM
ANGLE
AUDIO
Picture Zoom (DVD-Video only)
You can enlarge specific portions of a picture and select the zoom ratio using the ZOOM button during
DVD playback.
Notes
• The subtitle cannot be enlarged nor can it’s position be changed.
• The picture zoom feature does not work with a Video CD.
• During picture zoom, “ZOOM1” or
“ZOOM2” appears on-screen for 5 seconds.
• Zooming, on some discs, may result in poor picture quality, or may not operate at all.
Press ZOOM
repeatedly to change display as follows.
• You can enlarge the center portion of the image to one of 2 magnifications.
■
Use the
, ,
and buttons to move the position up, down, left and right.
37
D4753S P36-60.p65
37 2003/03/13, 11:32
Disc Operation (continued)
Title Menu (DVD only)
Some DVDs have more than one title, e.g. movies.
If the disc offers a title menu, you can select the desired title number. (Operation may vary according to the disc.)
1
T I TLE MENU
Dogs Cas t l es
Love r s B i r ds
Press TITLE*
in Play mode to display the title screen.
2
<Example>
T I TLE MENU
Dogs Cas t l es
Love r s B i r ds
B i rds of the world
Press
or
NUMBER keys
to select a title, and
press SET
or
PLAY
to start playing.
• “Pressing SET or PLAY” is not necessary when using
NUMBER keys.
PLAY
STOP
<Example>
DVD Menu (DVD only)
DVDs may offer a special menu. This menu may include guides to unique contents, audio/subtitle languages, etc.
Although contents and operation may vary, the following steps show basic steps for using the menu.
1
DVD MENU
1 . SUBT I TLE
2 . AUD I O
3 . ANGLE
Press
MENU
in Play mode to display
DVD MENU.
<Example>
NUMBER keys
CLEAR
ACTION
SELECT
MENU
SET
TITLE
2
38
DVD MENU
1 . SUBT I TLE
2 . AUD I O
3 . ANGLE
<Example>
Press
or
NUMBER keys
to select an item, and
press SET
or
PLAY
to perform.
• “Pressing SET or PLAY” is not necessary when using
NUMBER keys.
Repeat step 2 if there is more than one menu
.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P36-60.p65
38 2003/03/13, 11:32
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
You can program specific tracks and order of play.
1
Press ACTION
to display DVD MAIN MENU.
2
3
Program Play (Video CD/CD only)
DVD MAIN MENU
D I SC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
TV MODE
: AUTO
: 4 : 3 L e t t e r b o x
P A R E N T A L L O C K : L E V E L 8
PLAY MODE
SELECT
SET
END
:
: SET
: ACT I ON
PLAY MODE
PROGRAM PLAY
RANDOM PLAY
SELECT
SET
END
:
: SET
: ACT I ON
Press
to select
“PLAY MODE,” and
press SET
to display.
Press
to select
“PROGRAM PLAY,” and
press SET
to display.
4
1
2
PROGRAM PLAY
D I SC
6 11 16
7 12 17
3 8 13 18
4 9 14 19
5 10 15 20
CLEAR LAST
CLEAR ALL
SELECT
SET
END
:
: SET
: ACT I ON
PROGRAM
5 8
15 6
1 13
3 2
2
START
Press
to select a track number (Track numbers on disc are displayed.), and
press SET
.
• Repeat step 4 to select another track.
• The selected track is added on the right side.
5
1
2
3
PROGRAM PLAY
D I SC
6 11 16
7 12 17
8 13 18
4 9 14 19
5 10 15 20
CLEAR LAST
CLEAR ALL
SELECT
SET
END
:
: SET
: ACT I ON
PROGRAM
5 8
15 6
1 13
3 2
2
START
Press
to select “START,” and
press
SET
to start play of programs in the sequence selected.
• To cancel,
press
STOP
during play, then
press
CLEAR
.
Ready Checklist
DECK is in DVD mode, press DVD.
Video CD or CD is inserted.
Program Repeat Play
(Video CD/CD only)
1
2
Do operation steps
1
through
5
at left on this page.
Press DISPLAY
to display Disc
Information screen.
(Disc Information Screen)
TRACK : 1
PBC : OFF
V I DEO CD
01 : 35 : 12
SET : SET NEXT : D I SPLAY
3
4
Press
DISPLAY
to display
DECK Information screen.
Press
SET
to enter Select mode.
Cursor move to “OFF.”
(DECK Information Screen)
5
SET : SET END : D I SPLAY
Press
to select “DISC.”
(DECK Information Screen)
PLAY
REPEAT : DISC
PROGRAM PLAY
SELECT :
SET : SET END : D I SPLAY
Notes
• Up to 15 tracks can be programmed.
• “ ” or “ ” (depending on disc) indicates additional
PROGRAM PLAY screen.
Press for next or previous screen.
• To clear the last program one by one
Press to move to “CLEAR LAST” and press
SET. (Pressing CLEAR on remote control also clears last program.)
• To clear all programs
Press to move to “CLEAR ALL” and press
SET. (Programs are also cleared when the power is turned off or the disc is removed.)
6
Press SET
to set mode.
Cursor move to “REPEAT.”
To cancel, select “REPEAT :
OFF” in step 5, then
press SET
.
39
D4753S P36-60.p65
39 2003/03/13, 11:32
Disc Operation (continued)
Tracks are played in a random order.
1
Press ACTION*
to display DVD MAIN MENU.
2
Random Play (Video CD/CD only)
DVD MAIN MENU
D I SC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
TV MODE
: AUTO
: 4 : 3 L e t t e r b o x
P A R E N T A L L O C K : L E V E L 8
Press
to select “PLAY MODE,” and
press SET
to display.
SELECT
SET
END
:
: SET
: ACT I ON
3
PLAY MODE
PROGRAM PLAY
RANDOM PLAY
SELECT
SET
END
:
: SET
: ACT I ON
Press
to select
“RANDOM PLAY,” and
press SET
to begin random play.
• To cancel,
press STOP
during play, then
press
CLEAR
.
Ready Checklist
DECK is in DVD mode, press DVD.
DISPLAY
PAGE
Setting the VOLUME ADJUST
Some DVDs are recorded in lower than average volume levels.
For these DVDs, this DECK can be set so that the average volume is increased.
Press VOL.ADJ
repeatedly to change “ON”
↔
“OFF.”
• “ON” or “OFF” lights up on Multi Function Display (about 3 seconds) when press VOL.ADJ.
Some DVD
[Volume level is low]
VOLUME ADJUST “OFF”
Volume is the original level.
VOLUME ADJUST “ON”
Volume level is increased when played back.
• “ON” is set ..... When a DVD is played back, the average volume is increased.
• “OFF” is set .... The volume level recorded on the disc is played back just as it is.
Notes
• This feature is available only for Dolby Digital sound tracks.
• When audio equipment is connected, setting the Sound Output level to “OFF” is recommended.
• If the sound becomes abnormal while playing a disc, set the Sound Output level to “OFF.”
40
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P36-60.p65
40 2003/03/13, 11:32
STOP
NUMBER keys
CLEAR
ACTION
SELECT
SET
VOLUME
ADJUST
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
DVD-Audio Operation
This DECK, equipped with a 192 kHz/ 24 bit Audio D/A converter, supports DVD-Audio recorded with high quality sound.
The DVD-Audio feature includes “Still Image Skip” and “Bonus Group Playback” functions. (See below.)
Please refer to “Basic DVD Operation” on pages 22 and 23.
Still Image Skip
DVD-Audio still images (only if contained) can be skipped over.
PAGE : 1
PAGE : 2
SELECT :
Press PAGE
in Play or Pause mode to display the still image and page number.
Each press of PAGE changes page number as shown below.
• Pressing PAGE on the last page returns to PAGE 1.
Press PAGE
Press PAGE Press PAGE
Press PAGE
PAGE : 1 PAGE : 2 PAGE : 3 .......
PAGE : XX
SELECT :
Note
• Still Image Skip function not available with all discs.
Bonus Group playback
Some DVD-Audio discs contain bonus groups. To enjoy these groups you may have to enter a password. Refer to the disc's jacket.
1
Note
Press DISPLAY
in stop mode to display “On-Screen Displays.”
• During playback, Bonus Group tracks cannot be selected.
2
GROUP
TRACK
: 2
: 1
DVD-AUDIO
00 : 12 : 34
Press
to select “GROUP,” and
press SET
.
Press
or
NUMBER keys
to select bonus group number, and
press SET
(see pp. 42, 43.)
SELECT :
SET : SET
Notes
NEXT : D I SPLAY
• If the proper secret code is already entered, Bonus Group tracks can be selected. (Secret code enter screen is skipped.)
• This code is specifically for the disc and differs from Parental Lock secret code
(p. 48). Please refer to disc jacket instructions.
3
Note
BONUS GROUP
ENTER 4-D I G I T CODE
---
Press NUMBER keys
to enter bonus group secret code, and
press SET
.
To Make Corrections
Press
repeatedly to move the cursor.
Press NUMBER keys
to make the correction.
• When the proper secret code has been entered, Bonus Group track 1 playback begins. If a mistake is made, the secret code enter screen is redisplayed.
4
Press CLEAR
to return to normal screen.
41
D4753S P36-60.p65
41 2003/03/13, 11:32
DVD Operation using On-Screen Displays
When
DISPLAY is pressed, On-Screen Displays show disc information (title/chapter/track number, elapsed playing time) and DECK information (repeat play, play mode).
1
Press DISPLAY*
in Play or Stop mode to display “On-Screen Displays.”
• Each
press
of
DISPLAY
changes the on-screen display as follows. (Refer to pp. 43, 44.)
➡
Selected disc information
Note
Selected DECK information
Normal Screen
DISPLAY button does not function while DVD TITLE
MENU is displayed.
2
Press
(or ) to select
an item,
and
press SET
.
3
Press
or NUMBER keys to select the setting, and
press SET
.
<Example of DVD-Video>
• When numbers are displayed (e.g. title number),
NUMBER keys are also available.
• If the number entered is not on the disc, the entry will have no effect.
Re-enter the correct number.
<Example of DVD-Audio>
• For more details, refer to the disc operation information.
To return to normal screen, press CLEAR
or
DISPLAY
repeatedly.
<Example of Video CD>
Ready Checklist
DECK is in DVD mode, press DVD.
DISPLAY
NUMBER keys
CLEAR
SELECT
SET
Notes
• When
DISPLAY
button is pressed during playback of a Video CD with
Playback control,
NUMBER keys
are not available on the displayed screen.
In this case,
press
DISPLAY
again to remove the displayed screen.
• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.
42
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P36-60.p65
42 2003/03/13, 11:32
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
Detailed Descriptions of each On-Screen Display
■
Disc information screen (for DVD-Video)
1. TITLE No.
• Select “TITLE”, and
press
SET
.
• Change the No. by
pressing
or
NUMBER keys
, and
press SET
.
2. CHAPTER No.
• Select “CHAPTER”, and
press SET
.
• Change the No. by
pressing
or
NUMBER keys
, and
press SET
.
3. Disc currently being played
4. Elapsed playing time
The screen may be changed by selecting the elapsed time.
• Select the elapsed playing time (“xx:xx:xx”), and
press SET
.
• Change the elapsed time by
pressing NUMBER keys
.
Hours
➛
Minutes
➛
Seconds are entered in order.
If the time entered is not on the disc, the entry will have no effect.
Re-enter the correct time.
e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.
Hour Minutes Seconds
• This function does not work with some discs.
1
2
T I TLE : 1
CHAPTER : 12
SELECT :
SET : SET
T I TLE : 1
CHAPTER : 12
DVD
01 : 12 : 55
NEXT : D I SPLAY
DVD
01 : -: --
3
4
ENTER : 0 - 9
SET : SET NEXT : D I SPLAY
If SET is pressed while making entries, unit returns to the condition it was in before entries were made.
■
Disc information screen (for DVD-Audio)
A. GROUP No.
• Select “GROUP”, and
press SET
.
• Change the No. by
pressing
or
NUMBER keys
, and
press SET
.
B. TRACK No.
• Select “TRACK”, and
press SET
.
• Change the No. by
pressing
or
NUMBER keys
, and
press SET
.
C. Disc currently being played
D. Elapsed playing time
The screen may be changed by selecting the elapsed time.
• Select the elapsed playing time (“xx:xx:xx”), and
press SET
.
• Change the elapsed time by
pressing
NUMBER keys
.
Hours
➛
Minutes
➛
Seconds are entered in order.
If the time entered is not on the disc, the entry will have no effect.
Re-enter the correct time.
e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.
Hour Minutes Seconds
• This function does not work with some discs.
A
B
■
Disc information screen (for Video CD/ CD) a. TRACK No.
• Select “TRACK”, and
press SET
.
• Change the No. by
pressing
or
NUMBER keys
, and
press SET
.
b. Playback control ON/OFF
[Video CD with playback control only] a b
ON Video CD menu play is displayed.
OFF Video CD menu play is not displayed.
c. Disc currently being played
Video CD CD
d. Elapsed playing time
GROUP
TRACK
ENTER : 0 - 9
SET : SET NEXT : D I SPLAY
If SET is pressed while making entries, unit returns to the condition it was in before entries were made.
SET
: 1
: 1
TRACK : 1
PBC : OFF
: SET
DVD-AUDIO
01 : -: --
V I DEO CD
01 : 35 : 12
NEXT : D I SPLAY c d
C
D
Notes
• Track No. and the elapsed playing time are not displayed during play started from menu of Video CDs with playback control.
• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.
43
D4753S P36-60.p65
43 2003/03/13, 11:32
DVD Operation using On-Screen Displays (continued)
■
DECK information screen (for DECK)
1. Repeat Play
• Select “REPEAT”, and
press SET*
.
• Change the desired mode during play by
pressing
, and
press SET
.
DVD-Video
DVD-Audio
CHAPTER
TRACK
Video CD/CD TRACK
TITLE
GROUP OFF
DISC
OFF
OFF
2. Play mode
[Video CD/ CD only] (See p. 39 or 40.)
PROGRAM PLAY program play
RANDOM PLAY random play
---normal play
1
PLAY
REPEAT : CHAPTER
SELECT :
SET : SET END : D I SPLAY
For your reference
•
CHAPTER/TITLE REPEAT PLAY (DVD-Video)
CURRENT PLAYBACK POSITION
CHAPTER REPEAT
TITLE REPEAT
NORMAL PLAY
TITLE chapter chapter chapter
2
PLAY
REPEAT : D I SC
RANDOM PLAY
SET : SET END : D I SPLAY
OPEN/
CLOSE
•
TRACK/GROUP REPEAT PLAY (DVD-Audio)
CURRENT PLAYBACK POSITION
TRACK REPEAT
GROUP REPEAT
NORMAL PLAY
GROUP track track track
GROUP track track track
POWER
PLAY
FF/REW
PAUSE
STOP
•
TRACK/DISC REPEAT PLAY (Video CD/CD)
CURRENT PLAYBACK POSITION track track track
TRACK REPEAT
DISC REPEAT
NORMAL PLAY
NUMBER keys
SKIP
SKIP
SELECT
SET
ACTION
Note
• For repeat play in VCR mode, see p. 32.
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
44
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P36-60.p65
44 2003/03/13, 11:32
MP3/WMA/JPEG Playback Operation
This unit can play MP3/WMA/JPEG format CD-R or
CD-RW recorded for personal use on a PC, etc.
Some discs may not play due to the condition of the recording.
1
Press POWER
on the remote or DECK.
2
Press OPEN/CLOSE,
then place an MP3/WMA/JPEG disc into the disc tray.
Press OPEN/CLOSE
to close.
3
• MP3/WMA/JPEG menu is displayed.
• Playback starts automatically
(except JPEG files).
• CD directory is displayed.
<Example>
Function
Status
PLAY 00 : 00 : 00
Counter
Folder area
(Current folder appears green.)
ROOT . .
VA END_WALTZ
TECHNO DD_CUB I C
POPS NOCTURNE
JAZZ NORN
Parent folder
File area
(Selected file/
PLAY MODE : NORMAL folder is highlighted.
Titles are
PLAY MODE
:MP3 file :WMA file
displayed up to 11 characters.)
:Folder :Parent folder
:JPEG file
<Example>
ROOT
(Diagram left shows CD directory structure as displayed in example
OSD above.)
MP3/WMA Playback
Do steps 1~3 on left.
a
Press
to select an MP3/WMA file (
/
)
.
(During STOP mode)
b
Press
SET
or
PLAY
to start playback.
■
Forward/Reverse Search
Press FF/SLOW+
or
REW/SLOW-
during play.
Press PLAY
to release.
• Search speed, slow at first, increases with each additional press of the button up to 5 levels.
■
Forward/Reverse Track Skip
Press SKIP |
or
| SKIP
during play.
Each press skips a track.
• If pressed within first 3 seconds of playback, skips to the previous track. If over 3 seconds, returns to top of track. (
| SKIP
only.)
• Put DECK in Stop mode before performing folder/file selection (see step 4.)
■
Pause
Press PAUSE
during play.
c
Press PLAY
to release.
Press STOP
to stop play.
d Press OPEN/CLOSE
to eject the disc.
The MP3/WMA/JPEG MENU is closed automatically.
Note
• Copyright protected files and files containing errors cannot be played back. The DECK skips to the next file.
VA
END_WALTZ
DD_CUB I C
NOCTURNE
NORN
TECHNO
POPS
JAZZ
Notes
• Only File (not Folder) area operation is possible.
• Files are displayed in the following order:
(!...0,1....9,A,B......Z).
4
•
Select file
(During STOP mode)
1)
Press
to select an MP3/WMA file ( / ).
➡
MP3/WMA Playback (see right)
2)
Press
to select a JPEG file ( ).
➡
JPEG Playback (see p. 46)
3)
Press SKIP |
(next) or
| SKIP
(previous) to skip a file/folder page (7files) in the File area.
•
Select folder
(During STOP mode)
1)
Press
to select a folder ( ).
2)
Press SET
to display files/folders contained in the folder.
•
Select parent folder
(During STOP mode)
1)
Press
to select a folder ( ).
2)
Press SET
to make changes to the previous directory display.
5
Press
ACTION
to return the DVD MAIN
MENU. (
➛
Press
ACTION
again to return to the MP3/WMA/JPEG MENU.)
■
Select PLAY MODE [MP3/WMA Playback]
(During STOP mode)
1)
Press
to move cursor to
PLAY MODE.
2)
Press
to select the desired PLAY
MODE (see below).
[PLAY MODE]
NORMAL:
All MP3/WMA files are selected and played back one time only.
SINGLE REPEAT:
The selected MP3/WMA file is played back repeatedly.
FOLDER REPEAT:
The MP3/WMA files contained in the selected folder are played back repeatedly. However, folders below the selected folder are not played back.
DISC REPEAT:
All MP3/WMA files are played back repeatedly.
45
D4753S P36-60.p65
45 2003/03/13, 11:32
MP3/WMA/JPEG Playback Operation (continued)
JPEG Playback
You can play back JPEG images.
Displayable Image Size
: 32x32~7680x7680 pixels
Note
• Some JPEG format may not be played back.
Do steps 1~3 on page 45.
1
Press
to select an JPEG file (
)
.
2
Press SET
or
PLAY
.
Selected JPEG file is displayed.
[JPEG Playback Screen]
■
Select PLAY MODE [JPEG Slide-show]
(During STOP mode) (See p. 45)
1)
Press
to move cursor to
PLAY MODE.
2)
Press
to select the desired PLAY
MODE (see below).
[PLAY MODE]
NORMAL:
All JPEG files are selected and played back one time only.
SINGLE REPEAT:
The selected JPEG file is played back repeatedly.
FOLDER REPEAT:
The JPEG files contained in the selected folder are played back repeatedly. However, folders below the selected folder are not played back.
DISC REPEAT:
All JPEG files are played back repeatedly.
3
<Example>
■
Returned on the MP3/WMA/JPEG MENU
➡
Press STOP
.
(See p. 45)
■
Next/Previous Search
➡
Press SKIP |
or
| SKIP
.
■
Start Slide-show
➡
REW/SLOW-
. (below)
Press
FF/SLOW+
or
■
Enlarging an image
■
Rotating an image
➡
Press ZOOM
. (P. 47)
➡
Press ANGLE
. (P. 47)
Press STOP
to return the MP3/WMA/
JPEG MENU.
JPEG Slide-show
(During JPEG Playback.)
JPEG files are displayed automatically
(about every 3 seconds) as a slide-show.
1
Press FF/SLOW+
or
REW/SLOW-
.
<Example>
<Example>
Operation can be done when files are in order, such as in the diagram below.
ROOT
REW/SLOW-
01 PIC
FF/SLOW+
Image changes every 3 seconds.
■
Cancel slide show
➡
Press
STOP
to return the MP3/WMA/
JPEG MENU. (See p. 45)
■
Still picture
➡
Press STILL
(only SLIDE).
➡
Press PLAY
to release.
■
Forward/Reverse File Skip
➡
Press SKIP |
or
| SKIP
.
Each press skips a file.
AAA
DDD
TTT
UUU
VVV
WWW
ZZZ
REW/SLOW-
FF/SLOW+
2
46
Press ACTION
to return to the DVD MAIN
MENU.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P36-60.p65
46 2003/03/13, 11:32
PLAY
REW/
SLOW-
STOP
SKIP
ACTION
SET
FF/
SLOW+
STILL
JPEG Zoom
(During JPEG Playback.)
You can enlarge specific portions of a JPEG picture and select the zoom ratio using the ZOOM button on the remote during JPEG Playback screen.
Set Zoom size.
Press ZOOM
repeatedly to change display as follows.
➡
Press
STOP
to return the MP3/WMA/JPEG MENU.
• You can enlarge the center portion of the image to one of 2 magnifications.
• Operation can be done during Rotation (below).
X 1.0 (ORIGINAL) X 1.5 (ZOOM 1) X 2.0 (ZOOM 2)
1st press 2nd press
SKIP
SELECT
ZOOM
ANGLE
3rd press
■
Use the
, ,
and buttons to move the position up, down, left and right.
(Position cannot be changed on X1.0
ORIGINAL images.)
1st press
JPEG Rotation
(During JPEG Playback.)
You can rotate a JPEG picture using the ANGLE button on the remote during JPEG Playback screen. (The JPEG picture will be rotated 90 ° clockwise.)
Set rotation.
Press ANGLE
repeatedly to change display as below.
➡
Press STOP
to return the MP3/WMA/JPEG MENU.
• Operation can be done during Zoom (above).
• The vertical/horizontal ratio of rotated JPEG images may vary when they are displayed.
2nd press 3rd press
4th press
MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and
Thomson multimedia.
Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries.
WMA is a compression format developed by Microsoft Corporation. It achieves the same sound quality as MP3 with a file size that is smaller than that of MP3.
D4753S P36-60.p65
47 2003/03/13, 11:32
47
DVD Lock Feature
*
Important:
If a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
You can prevent playback of DVDs of a specific rating level which may be unsuitable for children.
• Some DVDs are encoded with a rating level. If the disc rating is higher (stricter) than the one you preset, playback will be prohibited.
Ready Checklist
DECK is in DVD mode, press DVD.
DVD Lock (DVD-Video only)
A 4-digit code must be entered to view a blocked program or change rating settings.
1
Press ACTION*
to display DVD MAIN MENU.
2
DVD MAIN MENU
D I SC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
TV MODE
: AUTO
: 4 : 3 L e t t e r b o x
PARENTAL LOCK : LEVEL 8
Press
to select “PARENTAL LOCK,” and
press
SET
to display.
SELECT
SET
END
:
: SET
: ACT I ON
3
4
ENTER 4-D I G I T CODE
---
ENTER : 0
-
9
END : ACT I ON
To Make Corrections
Press
repeatedly to move the cursor.
Press NUMBER keys
to make the correction.
1)
Press NUMBER keys
to enter your secret code.
2) Enter same secret code again for confirmation.
3)
Press
SET
to display.
• Step 2) not necessary when changing rating or secret code.
• Take care that you are not observed entering the secret code.
Press
to select rating level, and
press
SET
to select “LOCKED” or
“UNLOCKED.”
Caution
Discs not encoded with rating level will play even if the jacket states it is for mature audiences. For these discs, the
DVD Lock Ratings will not work.
<When DVD Lock is activated>
,
PLAYER S RAT I NG L I M I T.
DO YOU WANT TO CHANGE THE
L I M I T?
YES
NO
SELECT :
SET : SET END : D I SPLAY
After DVD Lock is set and a blocked DVD is played, this message will appear.
The message may differ depending on the disc.
To continue viewing a blocked program for now,
Press
to select “YES” and
SET. Then, enter your 4 digit secret code (see step 3 left).
When “NO” is selected, blocked programs cannot be viewed.
<When blocked programs>
PROGRAM RATING EXCEEDED
LEVEL 0
: LOCK ALL, Playback of all DVDs, CDs, Video
CDs, WMA, MP3 and JPEG is prohibited.
(Use to prohibit play of mature theme DVDs not encoded with rating level.)
LEVEL 1
: mature theme DVDs
LEVEL 2
: DVDs expressly for children can be played back.
LEVEL 3 to 7
: DVDs for general audiences/children can be played back. (DVDs with mature content are prohibited.)
LEVEL 8
: NO LIMIT: (Factory preset)
All DVDs can be played back.
Change your secret code
• You will need your current code.
Do steps 1
~
2 left.
Enter current secret code.
Press CLEAR
to clear the code.
Do step 4 to enter new code.
Note
• DO NOT forget your secret code.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
48
D4753S P36-60.p65
48 2003/03/13, 11:32
Settings for DVD Operation
1
Press ACTION
to display DVD MAIN MENU.
2
DVD MAIN MENU
D I SC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
TV MODE
: AUTO
: 4 : 3 L e t t e r b o x
P A R E N T A L L O C K : L E V E L 8
Once initial settings are done, they remain in memory (even after power off) until changed. This means DECK will operate under the same conditions
(especially DVDs) each time.
Press
to select an item, and
press SET
.
Ready Checklist
DECK is in DVD mode, press DVD.
SELECT
SET
END
:
: SET
: ACT I ON
DISC LANGUAGES
(See below)
All languages offered on the disc can be set.
If the language not offered is set, the original disc language will be selected.
AUDIO OUTPUT
(See p. 50.)
You can set the audio output that comes from the digital audio output terminal.
STILL MODE
(See p. 53.)
To select “FIELD” (Field still) or “FRAME” (Frame still) to prevent jitter or make small text or fine patterns clearly visible in a still picture. When
“AUTO” is set “FIELD” or “FRAME” is selected automatically.
TV MODE
(See p. 53.)
To select whether the video material for a widescreen will be played back in the Pan & Scan style,
Letterbox style or 16 : 9 style.
3
4
5
NUMBER keys
CLEAR
ACTION
SELECT
SET
Disc Languages (DVD only)
To select and set the language of the audio soundtrack, subtitles, or title/DVD menus for all discs to be played.
DVD MAIN MENU
D I SC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
TV MODE
: AUTO
: 4 : 3 L e t t e r b o x
P A R E N T A L L O C K : L E V E L 8
SELECT
SET
END
D I SC LANGUAGES
AUD I O
SUBT I TLE
MENUS
: E n g l i s h
: AUTO
: E n g l i s h
SELECT
SET
END
:
: SET
: ACT I ON
:
: SET
: ACT I ON
Press
to select
“DISC LANGUAGES,” and
press SET
to display screen.
Press
to select an item, and
press SET
repeatedly for desired language.
(Please refer right.)
Press ACTION
to redisplay DVD MAIN
MENU and go to step 2 to setup another item.
Or,
press ACTION
twice to exit.
“AUDIO” selections
(Factory preset: English)
To select the audio soundtrack language.
English
/
Spanish
/
French
/
Japanese
Original
: Original disc language
OTHER
✱✱✱✱
: Other language selection* 1
“SUBTITLE” selections
(Factory preset: AUTO)
To select the subtitle language.
AUTO:
Same language selected for “AUDIO”
•
If language set for “AUDIO” is used in playback, subtitles will not appear.
•
If another language is used during playback, the subtitles will appear in the language selected at “AUDIO” setup.
English
/
Spanish
/
French
/
Japanese
OTHER
✱✱✱✱
:
Other language selection* 1
“MENUS” selections
(factory preset: English)
To select the language used in title menus or DVD menus.
English
/
Spanish
/
French
/
Japanese
OTHER
✱✱✱✱
:
Other language selection* 1
To enter OTHER
✱✱✱✱
code number,
Press NUMBER keys
(Please refer to language codes on p. 54).
To make corrections,
press
repeatedly to delete language code number, and correct.
* 1 If the selected language is not offered, the original disc language is selected.
49
D4753S P36-60.p65
49 2003/03/13, 11:32
Settings for DVD Operation (continued)
Audio Output
Ready Checklist
DECK is in DVD mode, press DVD.
Select the digital output to be output from the optical digital audio output connector of DECK.
1
2
3
Press ACTION*
to display DVD MAIN MENU.
Type of amplifier
to be connected
Recommended setting
LPCM
( DV D )
Dolby
Digital
D T S
DVD MAIN MENU
D I SC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
TV MODE
: AUTO
: 4 : 3 L e t t e r b o x
P A R E N T A L L O C K : L E V E L 8
SELECT
SET
END
:
: SET
: ACT I ON
Press
to select
“AUDIO OUTPUT,” and
press SET
to display screen.
No amplifier is connected
AV amplifier (with digital audio input connector) without Dolby Digital/DTS decoder
AV amplifier including
Dolby Digital decoder
P C M
P C M
PCM*
1
Bitstream
PCM*
1
P C M
AUD I O OUTPUT
LPCM(DVD) : OFF
D o l b y D i g i t a l : B i t s t r e a m d t s : B i t s t r e a m
DRC
SPEAKER SETUP
: OFF
SELECT
SET
END
:
: SET
: ACT I ON
Press
to select an item, and
press SET
repeatedly for output. (See below.)
AV amplifier including
Dolby Digital/DTS decoder
P C M Bitstream Bitstream
*
2
• Make settings according to amplifier connected to optical audio output as shown in above table.
■
“LPCM (DVD)” selections
OFF:
Linear PCM of less than 48 kHz/16 bit is output. When playing DVDs recorded in linear
PCM of over 48 kHz/20 bit, no digital audio is output. (Factory preset)
PCM:
When playing DVDs recorded in linear PCM of
48 kHz/20 bit/24 bit or more, digital audio converted to 44.1 kHz/16 bit or 48 kHz/16 bit is output.
(Digital output of PCM audio is restricted to 48 kHz/16 bit or below for copyright protection.)
■
“Dolby Digital” selections
Bitstream:
Dolby Digital bitstream (1 ch - 5.1 ch) is output. (Factory preset)
PCM:
When you have connected a amplifier that doesn’t have a built-in Dolby Digital decoder.
■
“dts” selections
Bitstream:
DTS bitstream is output. (Factory preset)
PCM:
When you have connected a amplifier that doesn’t have a built-in DTS decoder.
■
“DRC (Dynamic Range Compression)” selections
OFF:
Normal audio range is selected. (Factory preset)
ON:
For dynamic sound even at low volume, this is useful for late-night listening. [Dolby Digital
DVDs only].
*1 When connecting an amplifier (with an optical digital input connector) which does not contain the Dolby Digital or DTS decoder, be sure to select “PCM”.
If “Bitstream” is selected, starting DVD play may cause such a high level of noise as to be harmful to your ears and damage the speakers.
*2 When a DTS decoder is connected, please select “Bitstream” in “dts”.
■
SPEAKER SETUP
➡
See pages 51, 52, 53.
4
Press ACTION
to redisplay DVD MAIN
MENU and go to step 2 to setup another item.
Or,
press ACTION
twice to exit.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
50
D4753S P36-60.p65
50 2003/03/13, 11:32
*
Important:
If a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
Speaker Output Setup
Set the number of speakers connected to the receiver
(amplifier, decoder.) (See pp. 14, 15.)
1
2
Do steps 1~3 on page 50.
LPCM(DVD) : OFF
D o l b y D i g i t a l : B i t s t r e a m d t s
DRC
SPEAKER SETUP
: B i t s t r e a m
: OFF
SELECT
SET
END
AUD I O OUTPUT
:
: SET
: ACT I ON
Press
to select “SPEAKER
SETUP,” and
press
SET
to display
SPEAKER SETUP screen.
3
SPEAKER SETUP
Press
to select “SPEAKER
SPEAKER SIZE
OUTPUT BALANCE
DELAY TIME
OUTPUT,” and
SELECT
SET
END
:
: SET
: ACT I ON
press SET
repeatedly.
(See below.)
■
SPEAKER OUTPUT
MULTI-CHANNEL:
(Factory preset)
Use this setting when 3 or more speakers are connected. In this case, it is necessary to set
[SPEAKER SIZE], [OUTPUT BALANCE], and
[DELAY TIME].
2-CHANNEL:
When 2 speakers are connected, it is not necessary to set [SPEAKER SIZE], [OUTPUT
BALANCE], and [DELAY TIME] (these setting menu are not displayed.)
4
Press ACTION
three times to exit.
Speaker Size Setup
Speaker frequency properties and the existence of speakers is set.
1
2
Do steps 1~2 of
“
Speaker Output Setup” above
.
FRONT
CENTER
SURROUND
: LARGE
: LARGE
SUBWOOFER : ON
SELECT
SET
END
SPEAKER SIZE
:
: SET
: ACT I ON
Press
to select “SPEAKER SIZE,” and
press
SET
to display SPEAKER SIZE screen.
Press
to select an item, and
press
SET
repeatedly. (See below table.)
ACTION
SELECT
SET
3
Menu item
FRONT
CENTER
SURROUND
SUBWOOFER
Press
Setting
LARGE
(factory preset)
SMALL
LARGE
(factory preset)
SMALL
NONE
LARGE
(factory preset)
SMALL
NONE
ON
(factory preset)
OFF
Remark
When the front speakers (R/L) supports low-frequency (under 100 Hz) reproduction.
Select when the front speakers (R/L) does not support low-frequency reproduction.
When the center speaker supports low-frequency (under 100 Hz) reproduction.
Select when the center speaker does not support low-frequency reproduction.
If there is no center speaker.
When the surround speakers (R/L) supports low-frequency (under 100 Hz) reproduction.
Select when the surround speakers (R/L) does not support low-frequency reproduction.
If there is no surround speaker.
If there is a subwoofer.
If there is no subwoofer speaker.
ACTION
four times to exit.
** If SUBWOOFER is set to “OFF,” the front speakers are set to
“LARGE” automatically.
51
D4753S P36-60.p65
51 2003/03/13, 11:32
Settings for DVD Operation (continued)
Output Balance Setup
Adjust the volume level output from the speakers. To adjust, play a disc or set the “TEST SIGNAL”
(p.53) to ON. Then adjust while confirming the volume. (Even if “OFF” or "NONE" is set in “SPEAKER
SIZE,” the speaker OUTPUT BALANCE can still be set.)
1
2
Do steps 1~2 of “Speaker Output Setup” on page 51.
CENTER
SURROUND(R)
SURROUND(L)
SUBWOOFER
TEST SIGNAL
SELECT
SET
END
OUTPUT BALANCE
: 0dB
: 0dB
: 0dB
: OFF
:
: SET
: ACT I ON
Press *
to select “OUTPUT BALANCE,” and
press
SET
to display OUTPUT BALANCE screen.
Press
to select an item, and
press
SET
repeatedly.
(See below table.)
Menu item Setting
CENTER
SURROUND(R)
-6dB ~ +6dB
Remark
Adjust so that the center speaker volume is virtually the same level (-6dB ~ +6dB) as the front speakers.
Adjust so that the surround speaker(R) volume is virtually the same level (-6dB ~ +6dB) as the front speakers.
Adjust so that the surround speaker(L) volume is virtually the same level (-6dB ~ +6dB) as the front speakers.
SURROUND(L)
0dB
(factory preset)
SUBWOOFER
Adjust so that the subwoofer speaker volume is optimum.
However, because no test sound will come from the subwoofer, play a disc to confirm, then adjust.
TEST SIGNAL : Switch test signal used for OUTPUT BALANCE setting to “OFF” or “FRONT(L)”....
➡
See page 53.
3
Press ACTION
four times to exit.
Delay Time Setup
[See <Speaker Position> p.53.]
To enjoy 5.1 CH sound, it is ideal to place all speakers, except the subwoofer, in a circular arrangement. (See <Speaker Position> p. 53.)
If this is not possible, setting Delay Time gives the sound output a delayed effect which gives you the illusion of the ideal listening position. (See right.)
1
Do steps 1~2 of “Speaker Output
Setup” on page 51.
2
Press
to select “DELAY TIME,” and
press SET
to display DELAY TIME screen.
Press
to select an item, and
press SET
repeatedly. (See below.)
• , : Delay time as 0ms
(Factory prest)
• ,
<
: Find the distance
B1
,
C1
in the table (below) and change to the recommended setting.
B1
Center speaker
Distance
B1
1/2
Approx. 100 cm (3 feet)
Approx. 150 cm (5 feet)
Approx. 200 cm (6 feet)
Setting
1.3 ms
2.6 ms
3.9 ms
5.3 ms
Menu item Remark
C1
Surround speaker
Setting
0ms 1ms 2ms 3ms 4ms 5ms
CENTER Distance
C1
Setting
SURROUND
0ms 5ms 10ms 15ms 20ms
Setting a delay effect.
0ms
(Factory preset)
5.3 ms
Approx. 200 cm (6 feet)
Approx. 400 cm (12 feet) 10.6 ms
Approx. 600 cm (18 feet)
3
Press
ACTION
three times to exit.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
52
15.9 ms
D4753S P36-60.p65
52 2003/03/13, 11:32
*
Important:
If a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
Test Signal Setup
This feature assists in the setting of
OUTPUT BALANCE. Starting with (L) front speaker, a test sound is output in clockwise order. While the test signal is output, adjust the output of the center speaker and
Surround speaker (R/L).
(See “Output Balance Setup.” P. 52.)
1
Do steps 1~2 of “Output
Balance Setup” on page 52.
2
OUTPUT BALANCE
CENTER
SURROUND(R)
SURROUND(L)
SUBWOOFER
: 0dB
: 0dB
: 0dB
: 0dB
Press
to select “TEST
SIGNAL,” and
press SET
.
(See below.)
SELECT
SET
END
:
: SET
: ACT I ON
Still Mode
Set to reduce jitter in a displayed still picture or a motion picture.
1
2
Press ACTION
to display DVD MAIN MENU.
DVD MAIN MENU
D I SC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
TV MODE : 4 : 3 L e t t e r b o x
P A R E N T A L L O C K : L E V E L 8
Press
to select “STILL MODE,” and
press SET
repeatedly for mode. (See below.)
SELECT
SET
END
:
: SET
: ACT I ON
No sound will come from the subwoofer.
Adjust as desired when playing a disc.
While the TEST SIGNAL is output, if the setting change in the OUTPUT BALANCE
(p. 52) is under 2 seconds, the output will switch to the next speaker. The speaker name from which the TEST SIGNAL is currently being output is displayed.
(Example; "TEST SIGNAL : CENTER")
3
OFF FRONT(L)
2sec
CENTER
2sec
FRONT(R)
2sec
SURROUND(L)
Press ACTION
2sec
2sec
SURROUND(R)
four times to exit.
AUTO:
“FIELD” (Field still) or “FRAME” (Frame still) is automatically selected during the still mode.
(Factory preset)
FIELD:
“FIELD” (Field still) is always selected.
This setting will reduce jitter when compared with “AUTO” on some discs.
FRAME:
“FRAME” (Frame still) is always selected.
Some texts and fine patterns will be seen clearly when compared with “AUTO” on some discs.
3
Press
ACTION
to exit this mode.
TV Mode
Set the screen display style for wide-screen video material playback.
1
2
Press ACTION
to display DVD MAIN MENU.
DVD MAIN MENU
D I SC LANGUAGES
AUDIO OUTPUT
ST I L L MODE : AUTO
TV MODE : 4 : 3 L e t t e r b o x
P A R E N T A L L O C K : L E V E L 8
Press
to select “TV
MODE,” and
press SET
repeatedly for mode.
(See below.)
SELECT
SET
END
:
: SET
: ACT I ON FRONT(L) FRONT(R)
CENTER
Listening position
SURROUND(L)
B1
SUBWOOFER
SURROUND(R)
C1
4:3 Pan & Scan
(Factory preset) :
Wide-screen video data is played in
Pan & Scan style (left and right of screen is trimmed.)
• Video data not formatted in Pan & Scan will play in letterbox style.
4:3 Letterbox
:
Wide-screen video data is played in
Letterbox style (top and bottom of screen has black margin).
16:9
:
Set “16:9” when using Wide-screen TV.
<Speaker Position>
3
Press ACTION
to exit this mode.
[
Pan & Scan (Factory preset)]
TV Mode
Example
[
Letterbox]
53
D4753S P36-60.p65
53 2003/03/13, 11:32
Language Code List
Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or
“MENUS” (see p. 49).
Code Language
6565
Afar
6566
Abkhazian
6570
Afrikaans
6577
Ameharic
6582
Arabic
6583
Assamese
6588
Aymara
6590
Azerbaijani
6665
Bashkir
6669
Byelorussian
6671
Bulgarian
6672
Bihari
6678
Bengali; Bangla
6679
Tibetan
6682
Breton
6765
Catalan
6779
Corsican
6783
Czech
6789
Welsh
6865
Danish
6869
German
6890
Bhutani
6976
Greek
6978
English
6979
Esperanto
6983
Spanish
6984
Estonian
6985
Basque
7065
Persian
7073
Finnish
7074
Fiji
Code Language
7079
Faroese
7082
French
7089
Frisian
7165
Irish
7168
Scots Gaelic
7176
Galician
7178
Guarani
7185
Gujarati
7265
Hausa
7273
Hindi
7282
Croatian
7285
Hungarian
7289
Armenian
7365
Interlingua
7378
Indonesian
7383
Icelandic
7384
Italian
7387
Hebrew
7465
Japanese
7473
Yiddish
7487
Javanese
7565
Georgian
7575
Kazakh
7576
Greenlandic
7577
Cambodian
7578
Kannada
7579
Korean
7583
Kashmiri
7585
Kurdish
7589
Kirghiz
7665
Latin
Code Language
7678
Lingala
7679
Laothian
7684
Lithuanian
7686
Latvian, Lettish
7771
Malagasy
7773
Maori
7775
Macedonian
7776
Malayalam
7778
Mongolian
7779
Moldavian
7782
Marathi
7783
Malay
7784
Maltese
7789
Burmese
7865
Nauru
7869
Nepali
7876
Dutch
7879
Norwegian
7982
Oriya
8065
Panjabi
8076
Polish
8083
Pashto, Pushto
8084
Portuguese
8185
Quechua
8277
Rhaeto-Romance
8279
Romanian
8285
Russian
8365
Sanskrit
8368
Sindhi
8372
Serbo-Croatian
8373
Singhalese
Code Language
8375
Slovak
8376
Slovenian
8377
Samoan
8378
Shona
8379
Somali
8381
Albanian
8382
Serbian
8385
Sundanese
8386
Swedish
8387
Swahili
8465
Tamil
8469
Telugu
8471
Tajik
8472
Thai
8473
Tigrinya
8475
Turkmen
8476
Tagalog
8479
Tonga
8482
Turkish
8484
Tatar
8487
Twi
8575
Ukrainian
8582
Urdu
8590
Uzbek
8673
Vietnamese
8679
Volapük
8779
Wolof
8872
Xhosa
8979
Yoruba
9072
Chinese
9085
Zulu
54
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P36-60.p65
54 2003/03/13, 11:32
Warning and Instruction Displays
These displays will alert you to a missed operation or provide further instructions.
OSD
PLEASE SET CLOCK BY
PRESSING ACTION KEY
PLEASE PREPARE FOR TIMER
REC
CHECK CASSETTE
RECORD TAB
NO CASSETTE
TO CANCEL TIMER REC
HOLD DOWN STOP KEY
FOR APPROX 3 SEC
VIDEO HEADS MAY NEED
CLEANING PLEASE INSERT
HEAD CLEANING CASSETTE
OR REFER TO MANUAL
END : PLAY
VCR LOCK ACTIVATED
REMOTE CONTROL IS SET
TO CABLE/DSS MODE
USE VCR : VCR KEY
USE DVD : DVD KEY
REMOTE CONTROL IS SET
TO TV MODE
USE VCR : VCR KEY
USE DVD : DVD KEY
PLEASE CHECK THE DISC,
AND FOR STAINS OR
SCRATCHES ON DISC
THIS DISC MAY NOT BE PLAYED
IN YOUR REGION
THIS TYPE OF DISC CANNOT BE
PLAYED. PLEASE INSERT A
DIFFERENT DISC
CANNOT PLAY THIS FILE
THIS FILE IS PROTECTED
IT IS PROHIBITED TO COPY
DVD/VIDEO CD/CD TO VHS
Caution
If you attempt to set or review a Timer
Recording and the Clock is not set...
If DECK is not in Stop mode or a cassette with record tab is not inserted 2 minutes before a
Timer Recording is about to begin...
If you press REC on the remote control or DECK, and a cassette is inserted with no record tab...
If you press PLAY, FF, REW, or REC on the remote control or DECK without a cassette inserted...
If you press STOP or POWER during a Timer
Recording...
(visible in VCR mode only)
If head cleaning becomes necessary while playing back a tape...
Page
24
24
25
6
20
21
25
6
If you press a function button other than STOP/
EJECT or POWER while DECK is in VCR Lock mode...
If you press an invalid key on the remote while in CABLE/DSS mode...
33
28
29
34
If you press an invalid key on the remote while in TV mode...
28
29
34
If you press PLAY, and DECK reads data from a stained or scratched disc in DVD mode.
4
Playback of a disc with different region number was attempted. Only discs marked region “1”,
“ALL”, or those that include “1” are playable on this DECK.
An unusable disc is inserted in the DECK.
3
4
This file format cannot be played.
(Appears during MP3/WMA/JPEG file playback)
This file is copyright protected and cannot be played back. (Playback is prohibited.)
(WMA only)
If you press REC in DVD mode...
45
45
21
55
D4753S P36-60.p65
55 2003/03/13, 11:32
Before Requesting Service
Check the following points if you are having trouble with your DECK.
Power
No power…
Power turns itself off...
Recording & Playback
TV program cannot be recorded...
Correction
• Completely insert Power Plug into an AC outlet.
• Set POWER button to on.
• Make sure power source is active.
• Auto power-off (shutoff) occurs after about 5 min.
in DVD mode with no operation, or if there is no broadcast signal in TV or Playback mode.
Turn the power back on. (pp. 23, 33)
Correction
• Check connections between DECK, external antenna, and TV.
• Check channel selections.
• Make sure your antenna system (CABLE or TV) is correctly set. (Channels [p. 18])
• Make sure cassette record tab is intact. (p. 6)
Timer recording cannot be performed…
There is no playback picture, or the playback picture is noisy or contains streaks...
During special effects playback, picture may contain some vertical jitter when using a TV with an
Automatic Vertical Hold Control...
DECK cannot be controlled...
• Confirm that clock is set to current time and date.
• Make sure Cable/DSS box (if used) is left on and tuned to channel to be recorded.
• Set recording start/stop times correctly. (p. 24)
• Timer recording may not be performed or continued if a power interruption occurs before or during a
Timer Recording, even after power is restored.
• Select channel 3 or 4 on TV to match VCR output channel (3 or 4) (p. 16) or select LINE.
• Set VCR/TV selector to “VCR.”
• Adjust TRACKING control in either direction. (p. 6)
• Try Head Cleaning. (p. 6)
• Set TV’s Vertical Hold Control to MANUAL, then adjust.
Remote Control
DECK cannot be remote controlled...
PROG buttons do not respond...
• Make sure DECK power is on.
• Check Remote batteries.
• Make sure VCR LOCK is set to off. (p. 33)
• Make sure Remote is in proper mode. (p. 28)
• Make sure Timer Recording is not in progress.
Correction
• Make sure DECK power is on.
• Make sure Remote is in VCR mode.
• Aim Remote Control directly at remote sensor on DECK. (p.9)
• Avoid any object blocking signal path.
• Check Remote batteries. (p. 4)
• Exposing DECK remote sensor to direct fluorescent or outdoor light may cause signal interference.
• PROG functions are not available in COMPONENT
Video Output and S-VIDEO OUT. Set TV to either RF
IN or VIDEO IN. (p. 10)
• Check Remote batteries. (p. 4)
• Press VCR or DVD button for DVD/VCR mode. (p. 28)
56
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P36-60.p65
56 2003/03/13, 11:32
Check the following points if you are having trouble with your DECK.
DVD/ Video CD/ CD
Play fails to start even when PLAY is pressed...
Play starts but then stops immediately...
Picture is distorted during rapid advance or rapid reverse...
No Forward/Reverse Scene Search play...
Play does not start even when title is selected...
Audio soundtrack and/or subtitle language is not the one selected at the initial settings...
No subtitles...
Correction
• This DECK cannot play discs other than DVDs,
Video CDs and CDs.
• The disc may be dirty and require cleaning.
• Be sure disc is installed with label side up.
• The picture will be somewhat distorted at times: this is normal.
• Some discs may have sections which prohibit
Forward/Reverse Scene Search. (p. 23)
• Confirm the “DVD LOCK” setting. (p. 48)
Alternative audio soundtrack
(or subtitle) language cannot be selected...
Angle cannot be changed...
Miscellaneous
Programs cannot be viewed on TV...
Video cassette cannot be inserted...
Video cassette ejects when a recording is started or the power is turned off for timer recording...
In Stop mode, the motor (CYLINDER) continues to rotate...
• If the audio soundtrack and/or subtitle language selected at DVD initial settings does not exist on the disc, it will not be accessible.
• Subtitles appear only when available on disc.
• “OFF” is selected at the changing subtitle language. Select “ON” at the “Subtitle Languages” section (p. 36) to display the subtitles.
• Alternative language cannot be selected with discs which do not contain more than one language.
• For some discs, alternative language cannot be selected with the AUDIO or SUB TITLE button.
Try selecting it from the DVD MAIN MENU if available.
• This function is dependent on software availability.
Even if disc has multiple angles, they may be recorded for specific scenes only (ANGLE indicator on DECK lights up). (p. 37)
Correction
• Make sure TV is set to output of DECK.
• Check connections between DECK, external antenna, and TV.
• Set VCR/TV selector to “TV.” (p. 21)
• Make sure proper signal source is selected.
• Insert the cassette with window side up; record tab facing you.
• Make sure cassette record tab is intact. (p. 6)
The disc cannot be removed..
• To enable Quick play mechanism, the cylinder will rotate for about 3 minutes. This reduces response time from Stop to Play mode.
• First, unplug DECK. Then, prepare a rigid wire
(e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc. (p. 9)
If you cannot resolve the problem, please call the Customer Call Center for product assistance at 1-800-211-PANA (7262).
To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262).
or send e-mail to : [email protected]
57
D4753S P36-60.p65
57 2003/03/13, 11:32
Limited Warranty
PANASONIC CONSUMER ELECTRONICS COMPANY,
DIVISION OF MATSUSHITA ELECTRIC
CORPORATION OF AMERICA
One Panasonic Way Secaucus, New Jersey 07094
PANASONIC SALES COMPANY, DIVISION OF MATSUSHITA
ELECTRIC OF PUERTO RICO, INC.,
AVE. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Panasonic/Quasar Video Products
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship, Panasonic
Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase
(“warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the warrantor.
Product
Parts
Camcorder
One (1) Year (except
CCD Image Sensor)
CCD Image Sensor - 6
(Six) Months
DVD/VCR Deck,
A/V Mixer
One (1) Year
TV/VCR, TV/DVD,
TV/DVD/VCR
Combination
One (1) Year (except
CRT)
CRT - Two (2) Years
TV/HDR
Combination
One (1) Year (except
CRT)
CRT - Two (2) Years
Rechargeable
Batteries
(in exchange for defective item)
Ten (10) Days
Tape
(in exchange for defective item)
Five (5) Days
Memory Cards
(in exchange for defective item)
Ninety (90) Days
Labor
Ninety (90) Days
Ninety (90) Days
Ninety (90) Days
Ninety (90) Days
Ninety (90) Days
Ninety (90) Days
Ninety (90) Days
Not Applicable
Not Applicable
Not Applicable
Service
Carry-In or Mail-In
Contact Number
1-800-211-PANA(7262)
Carry-In or Mail-In 1-800-211-PANA(7262)
Carry-In: 21” CRT and Smaller
In-Home or Carry-In:
22” CRT and Larger
1-800-211-PANA(7262)
In-Home or Carry-In 1-888-843-9788
Carry-In or Mail-In 1-800-211-PANA(7262)
Carry-In or Mail-In 1-800-211-PANA(7262)
Carry-In or Mail-In
1-800-211-PANA(7262)
During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. You must carry-in or mail-in your product or arrange for in-home service, as applicable, during the warranty period.
If non-rechargeable batteries are included, they are not warranted. This warranty only applies to products purchased and serviced in the United States or Puerto Rico. This warranty is extended only to the original purchaser of a new product which was not sold “as is”. A purchase receipt or other proof of the original purchase date is required for warranty service.
Carry-In, Mail-in or In-Home Service
For Carry-In, Mail-In or In-Home Service (as applicable) in the United States call toll free contact number listed above or visit Panasonic Web Site: http://www.panasonic.com
For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910.
In-Home service, if applicable, requires clear, complete and easy access to the product by the authorized servicer and does not include removal or re-installation of an installed product. It is possible that certain in-home repairs will not be completed in-home, but will require that the product, or parts of the product, be removed for shop diagnosis and/or repair and then returned.
58
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P36-60.p65
58 2003/03/13, 11:32
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT
COVER normal wear and tear or cosmetic damage, nor does it cover markings or retained images on the picture tube resulting from viewing fixed images (including, among other things, letterbox pictures on standard 4:3 screen TV’s, or non-expanded standard 4:3 pictures on wide screen TV’s, or onscreen data in a stationary and fixed location). The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, or commercial use (such as in a hotel, office, restaurant, or other business), rental use of the product, service by anyone other than a
Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY
COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY.
(As examples, this excludes damages for lost time, cost of having someone remove or re-install an installed unit if applicable, or travel to and from the servicer, loss of media or images, data or other memory or recorded content. The items listed are not exclusive, but are for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the warrantor’s Consumer Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE (INCLUDING COST OF AN IN-HOME SERVICE CALL, WHERE
APPLICABLE) WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR
RESPONSIBILITY.
For Product Information, Operating Assistance, Literature Request, Dealer Locations, and all Customer Service inquiries please contact:
1-800-211-PANA (7262)
,
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.
or send e-mail : [email protected]
For hearing or speech impaired TTY users, TTY : 1-877-833-8855
Web Site: http://www.panasonic.com
You can purchase parts, accessories or locate your nearest servicenter by visiting our Web Site.
Accessory Purchases:
1-800-332-5368 (Customer Orders Only)
For hearing or speech impaired TTY users, TTY : 1-866-605-1277
Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032
(6 am to 5 pm Monday - Friday; 6 am to 10:30 am Saturday; PST)
(Visa, MasterCard, Discover Card, American Express, Check)
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787)750-4300 Fax (787)768-2910
As of August 2002
59
D4753S P36-60.p65
59 2003/03/13, 11:32
Spanish Quick Use Guide/ Guía para rápida consulta
Realice la conexión de la antena o TV por cable antes de enchufar el cable de CA.
El DVD/VCR iniciará automáticamente la fijación de los canales y del reloj al enchufar el cable de CA.
CONEXIONES
Para Ant/Cable
1
➛
DVD/VCR
➛
TV
Conecte el cable de la antena al terminal IN
FROM ANT del DVD/VCR.
Televisor
DVD/VCR
Terminal IN FROM ANT.
1
Entrada (IN) desde
ANT./CABLE
2
Conecte el terminal OUT TO TV del DVD/VCR a la entrada de la antena VHF/UHF del TV con
2
Terminal
OUT TO TV
1
el cable RF incluido.
Conecte la salida de convertidor de cable al terminal IN FROM ANT.
Televisor
VHF/UHF
Para Sistema Digital de Satelite (DSS)/ Convertidor de cable
➛
DVD/VCR
DVD/VCR
Terminal
➛
IN FROM ANT.
TV
Estuche convertidor de TV por cable
2
Conecte el terminal OUT TO TV del DVD/VCR a la entrada de la antena VHF/UHF del TV con el cable RF incluido.
2
Terminal
OUT TO TV
1
Entrada (IN) desde
ANT./CABLE
CONFIGURACION INICIAL
VHF/UHF
1
2
Encienda el TV y cambie al canal 3.
3
Las fijaciones se realizan automáticamente.
Cuando termina las fijaciones, aparecerá la siguiente pantalla.
Enchufe el cable de CA.
El DVD/VCR se encenderá e iniciará las fijaciones de los canales y del reloj.
• Si no aparece la pantalla de abajo, compruebe la conexión del DVD/VCR-TV y si el canal del
TV está a 3, intennte cambiando al canal 4.
• Para cambiar el canal de salida del DVD/VCR, consulte las instrucciones de “Canal de salida del VCR” (informaciones en inglés página 19).
Enchufe el cable de CA.
6 / 8/ 20 03 SUN 2 : 20PM
DST : ON
SETT I NG : CH 10
AUTO CLOCK SET
COMPLETED
Si aparece en la pantalla “AUTO CLOCK SET IS
INCOMPLETE (FIJACION AUTOMATICA DEL
RELOJ ES INCOMPLETO)”, Ajuste el reloj como se describe a continuación.
CH AUTO SET PROCEEDING
CANCEL : STOP
Al inicio, el idioma de la pantalla está fijado a inglés.
Para cambiar el idioma, seleccione la pantalla
MENU (informaciones en inglés página 18).
AUTO CLOCK SET IS
I NCOMPLETE
PLEASE SET CLOCK BY
PRESSING ACT I ON KEY
AJUSTE MANUAL DEL RELOJ
AUTO CLOCK SET
PROCEEDING
CANCEL : STOP
Si está usanndo un convertidor de TV por cable y en su area hay un canal de Public Broadcast
Station (PBS), ajuste su convertidor al canal PBS de su area. Si está usando un receptor DSS, este debe estar apagado.
Si la fijación ha sido incompleta.
1 Presione la tecla ACTION en el control remoto para visualizar la pantalla del menú SET
CLOCK.
1 / /
SET CLOCK
:
DST : ON
- - - - - - - - -- - - - - - - -- - - - - -
SELE CT MONTH
Nota
• Los botones de funciones no funcionan durante la configuración inicial.
• Para retirar un cassette durante el ajuste automático, presione EJECT en el control remoto o STOP dos veces en el aparato. En este caso, los ajustes de los canales y la hora se deben hacer manualmente. Para los ajustes seleccione la pantalla MENU (informaciones en inglés página 18).
• Dependiendo de las condiciones, el ajuste automático puede durar más de 30 minutos.
En ese caso, presione STOP para detener el ajuste automático y realice los ajustes manualmente en la pantalla MENU.
2
SELECT :
SET :SET
EXIT : ACT I ON
Presione para seleccionar el mes y SET para ajustar. De la misma forma, seleccione y ajuste la fecha, año, hora y DST (hora de verano).
SET CLOCK
6 / 8 / 2003 SUN 2: 2 0 PM
DST : ON
- - - - - - - - -- - - - - - - -- - - - - -
SET COMPLETED
3 Presione dos veces la tecla ACTION para poner el RELOJ en marcha y salir.
PRECAUCIÓN
Al usar cables coaxiales RF del tipo “tuerca”, apriételos solamente con los dedos. Un apriete excesivo puede dañar los terminales.
60
D4753S P36-60.p65
60 2003/03/13, 11:32
1
Operaciones básicas para la reproducción
Inserte un cassette
,
• La alimentación del DECK se activa.
En la Pantalla de Visualización Multi
Función se ilumina “VCR”.
2
Presione PLAY
para reproducir el cassette.
• Si el cassette no tiene la lengüeta de prevención de grabación (página 6), se inicia la reproducción automáticamente.
Detalles especiales durante la grabación
Presione FF/SLOW+
o
REW/SLOW-
para búsqueda de escenas hacia delante/ hacia atrás.
Presione PLAY
para liberar. Durante la búsqueda, cada vez que
presione FF
o
REW
se cambia la velocidad como sigue:
[SLP] aprox.
21X
↔ aprox. 9X
[LP] aprox.
9X
↔ aprox. 7X
[SP] aprox.
7X
↔ aprox. 3X
Si la imágen se interrumpe con la velocidad de
21X, 9X o 7X, cambie la velocidad a 9X, 7X o
3X.
Presione PAUSE/STILL
para imagen Fija
(Congelada).
Presione PLAY
para liberar.
Presione PAUSE/STILL
en el modo de imagen fija para imágenes cuadro a cuadro.
Presione PLAY
para liberar.
Presione FF/SLOW+
o
REW/SLOW-
en el modo de imagen fija para cambiar la velocidad de las imágenes a cámara lenta.
3
Presione STOP
para detener el cassette.
Presione REW/SLOW-
o
FF/SLOW+
en el modo de parada para rebobinado/avance rápido del cassette.
Presione EJECT
en el control remoto, o
STOP/EJECT
en el DECK para expulsar el cassette.
Operaciones básicas para la grabación
1
Inserte el cassette con lengüeta de protección de grabación
(página 6).
Programación fácil para la grabación con temporizador
1
Presione PROG
para visualizar la pantalla de Programacion.
2
FECHA I N I C I O PARADA
ELEGIR :
FIJAR :SET
TERMINAR : PROG
CA
7 SAB --:-- --:-- --
ELEGIR FECHA DE I N I C I O
Orden para elegir
Ejemplo
Fecha de hoy 7
1) Para ajustar la FECHA de grabación, presione
para seleccionar:
1-31 = una vez, o
DIARIO = a la misma hora de lunes a viernes, o
SEMANA = a la misma hora cada semana y
presione SET
para ajustar.
8 9
31
1 2
/ Orden para elegir
6
DIARIO
SEMANAL
(SAB)
SEMANAL
(LUN)
SEMANAL
(DOM)
2) Para ajustar los ítems que quedan, presione
para seleccionar y
presione SET
para ajustar los tiempos de INICIO/PARADA,
CANAL, o entrada de LINEA (página 35), y velocidad del cassette (SP, LP, SLP).
Presione PROG
para finalizar PROGRAM.
3
FE I N I C PARADA CA VEL
7 2 : 00 P 3 : 20 P 02 SLP
-- -- : -- -- : -- -- --
-- -- : -- -- : -- -- --
-- -- : -- -- : -- -- --
CANCELAR: ADD / DLT
ELEGIR 1- 8 :
ENTRAR : SET
SAL I R : PROG
Presione
para seleccionar un número que no está usando para ingresar mas programas y
presione SET
para ajustar.
Luego repita el paso 2.
O
Presione nuevamente
PROG
para salir.
2 Presione CH
/
,
o
las teclas de números
para seleccionar el canal.
3 Presione SPEED
para seleccionar la velocidad de grabación (página 6)
• SP = Reproducción estándar,
• LP = Larga duración,
• SLP = Superlarga duración.
4 Presione REC
para comenzar a grabar.
• Para eliminar escenas indeseadas, presione
PAUSE/STILL para hacer una pausa, y al presionar nuevamente continua la grabación.
• No podrá ver otro canal durante la grabación.
5
Presione STOP
para detener la grabación.
Grabación de un toque
Presione REC
repetidamente para ajustar la hora de grabación (30 min - 4 horas).
• La videograbadora termina la grabación a una hora programada.
Grabación normal
0:30 1:00
4:00 3:00 2:00 1:30
61
D4753S P36-60.p65
61 2003/03/13, 11:32
Spanish Quick Use Guide/ Guía para rápida consulta
1
2
3
Operaciones básicas del DVD
Presione POWER
en el control remoto o el aparato.
Presione DVD
para seleccionar el modo DVD.
1)
Presione
OPEN/CLOSE
.
2) Ponga un disco en la bandeja de disco.
• Sujete el disco sin tocar ninguna de sus superficies, póngalo con el lado donde esté impreso el título hacia arriba, alinéelo con las guías y póngalo en su posición apropiada.
Disco de 3” (8 cm) / Disco de 5” (12 cm)
Funcionnamiento del DVD utilizando visualizaciones en pantalla
Cuando se presiona DISPLAY, la visualización en pantalla muestra la información del disco (título / capítulo
/ número de lista, tiempo transcurrido de reproducción, audio / idioma del subtítulo, y ángulo) e información
(repetir la reproducción, modo reproducción, Karaoke vocal encendido / apagado, etc.).
1
Presione DISPLAY
en el modo reproducción o parada para visualizar las visualizaciones en pantalla.
• Cada vez que se
presione DISPLAY
, la visualización en pantalla cambia como se muestra a continuación.
Información seleccionada del disco
4 Presione PLAY
para iniciar la reproducción.
La bandeja del disco se cierra automáticamente.
• Si está usando un DVD interactivo (Interactive
DVD) o un Vídeo CD con contol de reproducción (playback control) y aparece un menú de títulos (TITLE MENU) en la pantalla, siga al paso 5.
Información seleccionada del DECK
Pantalla normal
5 Presione
o las teclas numéricas para seleccionar el artículo deseado.
Presione
SET
o
PLAY
para la reproducción.
Si usa las teclas numéricas, la reproducción comienza automáticamente.
2
Presione
(o ) para seleccionar el ítem deseado.
Presione SET
para ajustar.
6
7
Presione STOP
para parar la reproducción.
Presione
OPEN/CLOSE
para expulsar el disco.
■
Para buscar una escena particular
Búsqueda hacia adelante
Presione FF/SLOW+
en el modo de reproducción.
Búsqueda hacia atrás
Presione REW/SLOW-
en el modo de reproducción.
(Para liberar,
presione PLAY
)
■
Para saltar un capítulo o una pista
Salto hacia adelante
Presione SKIP l
en el modo de reproducción.
Un capítulo (Vídeo DVD) o una pista (Audio
DVD/Vídeo CD/CD) se salta cada ves que se oprime la tecla.
Salto hacia atrás
■
Presione l SKIP
en el modo de reproducción.
■
Para ver una imagen fija
Presione PAUSE/STILL
durante la reproducción.
(Para liberar,
presione PLAY
)
■
Para ver imágenes cuadro a cuadro
(DVD/Vídeo CD)
Presione PAUSE/STILL
en el modo de imagen fija.
La imagen avanza un cuadro cada vez que presiona la tecla. (Para volver a la reproducción normal,
presione PLAY
)
■
Para ver en cámara lenta (DVD/Vídeo CD)
Presione FF/SLOW+
o
REW/SLOW-
en el modo de imagen fija.
(Para liberar,
presione PLAY
)
3
Presione
para seleccionar el ajuste deseado.
Presione SET
para ajustar.
Para volver a la pantalla normal,
Presione
repetidamente
CLEAR
o
DISPLAY
.
<Ejemplo (Vídeo DVD)>
T I TULO : 12
CAP I TULO : 11
GRUPO : 1
P I STA : 1
DVD
00 : 12 : 34
ELEG I R :
F I JAR : SET S I GU I ENTE: D I SPLAY
<Ejemplo (Vídeo CD)>
P I STA
PBC
: 12
: I NACT I VO
V I DEO CD
00 : 12 : 34
F I JAR : SET S I GU I ENTE: D I SPLAY
<Ejemplo (Audio DVD)>
DVD-AUDIO
00 : 12 : 34
ELEG I R :
F I JAR : SET T E R M I N A R : D I SPLAY
T I TULO : 12
CAP I TULO : 24
ELEG I R :
F I JAR : SET S I GU I ENTE: D I SPLAY
P I STA
PBC
: 17
: I NACT I VO
DVD
00 : 12 : 34
V I DEO CD
00 : 12 : 34
F I JAR : SET S I GU I ENTE: D I SPLAY
GRUPO : 1
P I STA : 1
DVD-AUDIO
00 : 12 : 34
ENTRAR: 0 - 9
F I JAR : SET T E R M I N A R : D I SPLAY
62
D4753S P36-60.p65
62 2003/03/13, 11:32
Fijaciones iniciales
Selección de IDIOMAS DEL
DISCO [DVD solamente]
1
2
3
4
5
Presione DVD
para seleccionar el modo DVD.
Presione ACTION en el modo de parada
para visualizar MENU.
Presione
para seleccionar el artículo deseado.
Presione SET
.
IDIOMAS DEL DISCO
Todos los idiomas ofrecidos en el disco pueden ser ajustados. Si el idioma ajustado no es ofrecido en el disco, se seleccionará el idioma original del disco.
SALIDA DE AUDIO
Puede usted ajustar la salida audio procedente del terminal de salida audio digital.
DETENER RASTREO
Para seleccionar “CAMPO” o “CUADRO fijo” para prevenir inestabilidad o para permitir ver textos pequeños o patrones finos claramente en el modo de imagen fija.
TV PREFERENCIA
Para seleccionar cuando el material del vídeo es para pantalla ancha y se quiere reproducir en el estilo
Pan&Scan, en el estilo Letterbox o en el estilo 16:9 en la pantalla.
Presione
para seleccionar el artículo deseado.
Presione SET
.
Volver a visualizar el menú de DVD para continuar el ajuste.
Presione ACTION
y pase al paso 3 para ajustar otro ajuste o, para salir,
presione
ACTION
tres veces.
Cambio del idioma de subtítulos
[Vídeo DVD solamente]
Seleccione “AUDIO”
(Fijación de fábrica : inglés)
Inglés / Español / Francés / Japonesa :
Original :
Se seleccionará el idioma original de cada disco.
OTRO
✱✱✱✱
:
Se puede seleccionar el otro idioma.
Seleccione “SUBTITULO”
AUTO :
Se seleccionará el mismo que fue seleccionado en la preparación de
“AUDIO”. (Fijación de fábrica)
• Si el idioma seleccionado en la preparación de “AUDIO” se utiliza durante la reproducción, los subtítulos no aparecerán.
• Si se utiliza otro idioma durante la reproducción, los subtítulos aparecerán en el idioma seleccionado en la preparación de
“AUDIO”
Inglés / Español / Francés / Japonesa :
OTRO
✱✱✱✱
:
Se puede seleccionar el otro idioma.
Seleccione “MENU”
(Fijación de fábrica : inglés)
Inglés / Español / Francés / Japonesa :
OTRO
✱✱✱✱
:
Se puede seleccionar el otro idioma.
Visión desde otro ángulo
[DVD solamente]
EI idioma de los subtítulos seleccionado al hacer las fijaciones iniciales se puede cambiar por otro idioma diferente, si éste se encuentra disponible.
1
ELEGIR
ACTIVO / INACTIVO :
:
TERMINAR : SUB TITLE
Presione SUBTITLE
durante la reproducción.
Cuando no haya subtítulos grabados, se visualizará “-” en lugar del número de idioma.
Algunos discos DVD tienen escenas que han sido filmadas simultáneamente desde ángulos diferentes.
Con estos discos, la misma escena podrá verse desde cada uno de estos ángulos diferentes utilizando el botón
ANGLE.
1
ANGULO : 1
Presione ANGLE
durante la reproducción para visualizar la selección del ángulo.
1
2
2
ELEGIR :
ACTIVO / INACTIVO :
TERMINAR : SUB TITLE
Presione
para seleccionar el idioma deseado.
Presione
para seleccionar “ACTIVO” o
“INACTIVO.”
Selección de vocal para los discos de Karaoke [DVD/Vídeo CD]
2
Presione AUDIO
durante la reproducción para visualizar la pantalla AUDIO.
ELEG I R :
ANGULO : 2
ELEG I R :
Presione
para seleccionar el ángulo deseado.
Cambio del idioma de la pista de sonido [DVD solamente]
ELEG I R :
TERMI NAR : AUDIO
Presione
(o ) para seleccionar el ajuste deseado.
Presione
(o ) para ajustar. (DVD solamente)
EI idioma de la pista de sonido seleccionado al hacer las fijaciones iniciales se puede cambiar por otro idioma diferente, si éste se encuentra disponible.
1
Presione AUDIO
durante la reproducción para visualizar
SONIDO en la pantalla.
ELEG I R :
TERMI NAR : AUDIO
• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF
• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF
2
Presione
para seleccionar idioma.
• Video CD LR L R
ELEG I R :
TERMI NAR : AUDIO
63
D4753S P36-60.p65
63 2003/03/13, 11:32
Spanish Quick Use Guide/ Guía para rápida consulta
Utilización de un menú de títulos
[DVD solamente]
Algunos discos con películas, vienen con dos o más títulos. Por ejemplo, si el disco tiene un menú de títulos grabados, el botón TITLE podrá utilizarse para seleccionar el título de la película.
1
Presione TITLE durante la reproducción.
Ahora se visualiza una lista de los títulos del disco.
2
T I TLE MENU
Dogs Cas t l es
Love r s B i r ds
Dogs
Presione
o
las teclas de números
para seleccionar el título deseado.
Presione SET
para elegir.
Utilización de un menú de DVD
[DVD solamente]
Algunos discos DVD ofrecen un menú especial.
Este menú incluye guías para contenidos únicos, audio, subtitulos, idiomas, etc. Aunque los contenidos y las operaciones se cambian, los siguientes son unos pasos básicos para el uso del menú.
1
2
Presione MENU
durante la reproducción.
El menú de DVD introducido en el disco se visualiza ahora.
DVD MENU
1 . SUBT I TLE
2 . AUD I O
3 . ANGLE
Presione
o
las teclas de números
para seleccionar el ítem deseado.
Presione SET
para elegir.
of the world
<ejemplo>
<ejemplo>
Ampliación de la imagen [Vídeo DVD solamente]
Durante la reproducción de un DVD, puede ampliar partes específicas de una imagen y seleccionar la relación de zoom usando el botón ZOOM.
Presione ZOOM
repetidamente para cambiar el tamaño de la imagen como se indica a continuación:
■
Use los botones
, ,
y para desplazar la posición hacia arriba, hacia abajo, hacia la izquierda o hacia la derecha.
2da
3da
1
2
3
Funcionamiento de la ejecución de MP3/WMA/JPEG
Puede utilizar esta unidad para reproducir audio de formato MP3/WMA/JPEG, grabado para uso personal con una computadora, etc., en un CD-ROM o CD-RW.
La ejecución no podrá realizarse en algunos casos, debido a las condiciones de la grabación.
Presione POWER
en el control remoto o DECK.
Presione OPEN/CLOSE
y a continuacion coloque un disco MP3/WMA/JPEG en la bandeja de discos.
Presione OPEN/CLOSE
para cerrarla.
Se visualizará el MENU MP3/WMA/JPEG y la ejecución se iniciará automáticamente. (Se visualizará el directorio del CD.)
Estado de la función
Area de las carpetas
(La carpeta visualizada actualmente se volverá verde)
REPROD
<ejemplo>
ROOT . .
VA END_WALTZ
TECHNO DD_CUB I C
POPS NOCTURNE
JAZZ NORN
MODE DE REPRODUCCION:
NORMAL
00 : 00 : 00
MODO DE REPRODUCCIÓN
: Archivo MP3 : Archivo WMA
Contador
Carpeta principal
Area de archivos
(El archivo/ la carpeta se visualiza con un cursor.)
: Archivo JPEG
4
■
Ejecución MP3/WMA/JPEG
(Durante el modo STOP)
Presione
para seleccionar un archivo MP3/WMA
( / ) o un archivo JPEG ( ), y
presione SET
o
PLAY
.
•
MP3/WMA
Búsqueda hacia adelante/hacia atrás
➡
Presione FF/SLOW+
o
REW/SLOW-
durante la ejecución.
Salto de pista hacia adelante/hacia atrás
➡
Presione SKIP |
o
| SKIP
durante la ejecución.
•
JPEG
Búsqueda siguiente/anterior
➡
Presione SKIP |
o
| SKIP
.
Inicie la muestra-diapositiva
➡
Presione FF/SLOW+
o
REW/SLOW-
.
Ampliar una imagen
➡
Presione ZOOM
.
Girar una imagen
➡
Presione ANGLE
.
Presione STOP
para detener la operación descrita arriba.
■
Seleccione MODO DE REPRODUCCION
(Durante el modo STOP)
Presione
para mover el cursor a MODO DE
REPRODUCCION, y
Presione
para seleccionar el
MODO DE REPRODUCCIÓN deseado.
[MODO DE REPRODUCCIÓN]
NORMAL
: Todos los archivos se reproducen sólo una vez
REPETICION DE UNA MUSIC
:
El archivo seleccionado se reproduce repetidamente.
REPETICION DE UN ARCHIVO
:
Los archivos que se encuentran en la carpeta
seleccionada se reproducen repetidamente.
REPETICION DEL DISCO
:
Todos los archivos se reproducen repetidamente.
:Carpeta :Carpeta principal
5
Presione
ACTION
para regresar al DVD MENU
PRINCIPAL.
64
D4753S P36-60.p65
64 2003/03/13, 11:32
1
Configuración de los altavoces
Presione POWER
en el control remoto o el aparato.
2
3
Presione DVD
para seleccionar el modo DVD.
AJUSTE DE ALTAVOCES
SAL I DA PARA ALTAVOCES :
MULT I - CANALES
TAMAÑO DEL ALTAVOZ
BALANCE DE SAL I DA
T I EMPO ATRAZADO
ELEG I R
F I JAR
:
: SET
TERM I NAR : ACT I ON
Presione
para seleccionar “AJUSTE DE
ALTAVOCES,” y
Presione
SET
para visualizar la pantalla
AJUSTE DE ALTAVOCES.
4
Presione
para seleccionar, y
presione
SET
para fijar.
■
SALIDA PARA ALTAVOCES
Fije el número de altavoces conectados al DECK.
MULTI-CANALES
(Predeterminado en fábrica)
Cuando están conectados 3 o más altavoces.
2 CANALES
Cuando están conectados 2 altavoces.
■
TAMAÑO DEL ALTAVOZ
Se determinan las propiedades de frecuencia del altavoz y la existencia de los altavoces.
FRENTE
(GRANDE [predeterminado en fábrica]/
PEQUEÑO)
CENTRO
(GRANDE [predeterminado en fábrica]/
PEQUEÑO/NINGUNO)
ENVOLVENTE
(GRANDE [predeterminado en fábrica]/PEQUEÑO/NINGUNO)
SUBWOOFER
(ENCENDIDO [predeterminado en fábrica]/APAGADO)
■
BALANCE DE SALIDA
Ajuste la salida de nivel de volumen para los altavoces.
CENTRO, ENVOLVENTE(DER)/(IZQ), SUBWOOFER
-6db ~ +6db (0db: predeterminado en fábrica)
SEÑAL PRUEBA
El sonido de prueba es la salida en sentido de las manecillas del reloj.
■
TIEMPO ATRAZADO
Configurar el tiempo atrazado. Da a la salida de sonido un efecto retrasado que le ofrece la ilusión de encontrarse en la posición de escucha ideal.
5
Presione ACTION
tres o cuatro veces para salir.
D4753S P36-60.p65
65 2003/03/13, 11:32
65
INDEX
DECK & VCR
A
ACTION button ................................. 8, 18
Accessories ............................................ 4
ADD/DELETE button
(Add or Delete a Channel) ............ 8, 19
Audio Broadcast types
(Stereo/SAP/Mono) ............................ 26
Audio Mode (Playback, Recording) .... 27
Auto Operation Functions .................... 31
Auto Shut-Off ........................................ 33
B
Batteries ................................................. 4
C
Channel (“SET UP CHANNEL”) .......... 18
Channel Up/Down,
Tracking/V-Lock Button .................... 6, 8
Clock (“SET CLOCK”) .......................... 18
Commercial Skip ................................. 31
Connections ................................. 12 ~ 15
Copy Your Tapes (Dubbing) ............... 35
COUNTER RESET button ............... 8, 32
Customer Services Directory ............... 59
D
DISPLAY button ............................... 8, 11
DSS/CABLE mode button ............... 8, 28
DST (Daylight Saving Time) ................ 19
E
EJECT button ................................... 8, 20
ENTER button
(For tuning TV Channel) ................ 8, 28
F
FAST FORWARD/SEARCH button .. 8, 20
H
Head Cleaning ...................................... 6
I
Index Search ........................................ 30
Indicator (Multi Function Display) ....... 11
Initial Setup (Ready to Play) ......... 16, 17
INPUT button ................................... 8, 35
L
Limited Warranty ........................... 58, 59
Location of Controls
(Remote, DECK) .......................... 8 ~ 10
M
Multi-Brand Control ....................... 28, 29
O
On-Screen Displays (VCR) ................. 11
One Touch Recording ......................... 21
P
PAUSE/STILL button (Still Picture) .. 8, 20
PLAY button (Playback a Tape) ...... 8, 20
POWER button ....................................... 8
PROG button (PROGRAM) .............. 8, 24
Program Clear, Review, Replace ....... 25
Program End Search ........................... 30
Q
Quality Picture ....................................... 6
R
REC button (Record on a Tape) ..... 8, 21
Record Tab ............................................ 6
Remote Sensor ...................................... 9
Remote Warning .................................. 34
Repeat Play ......................................... 32
Reset All Memory Functions ................. 9
REWIND/SEARCH button ............... 8, 20
S
SAP/Hi-Fi ............................................. 27
SEARCH
(Index and Program End Search) ..... 30
SLOW+/SLOW- button
(Slow Motion Picture) .................... 8, 20
Spanish Quick Use Guide ........... 60 ~ 65
Specifications ......................................... 7
SPEED button .................................. 8, 21
Still (Freeze) Picture ............................ 20
STOP button ..................................... 8, 20
T
Tape Position, Tape Status ................. 34
Timer Recording .................................. 24
Trouble Shooting ........................... 56, 57
TV mode button ................................ 8, 28
V
VCR Lock ............................................. 33
VCR mode button ............................ 8, 28
VCR/TV button ................................. 8, 21
VCR/TV Selector Feature .................... 32
VOLUME +/- button (TV Volume) .... 8, 28
W
Warning and Instruction Displays ....... 55
Weak Signal Display ........................... 33
Z
ZERO SEARCH button .................... 8, 32
66
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
D4753S P36-60.p65
66 2003/03/13, 11:32
DVD
A
ACTION button ................................. 8, 49
ANGLE button
(Multiple Angle Viewing) ......... 8, 37, 47
AUDIO button
(Audio Soundtrack Language) ...... 8, 36
Audio Output
(For Selecting Audio Output) ............. 50
Auto-Power Off Function ..................... 23
B
Bonus Group (For DVD-Audio) ........... 41
C
CLEAR button ............................ 8, 39, 48
Component Video Output .............. 10, 13
D
Delay Time Setup ................................ 52
Disc Languages ................................... 49
DISPLAY button
(“On-Screen Display”) .................... 8, 42
DTS ...................................................... 14
DVD-Audio ........................................... 41
DVD Lock Ratings ............................... 48
DVD Menu ........................................... 38
DVD mode button ............................ 8, 28
F
5.1ch Analog Audio Output ........... 15, 51
Frame by Frame Picture ...................... 23
Forward/Reverse Chapter/Track Skip ... 23
Forward/Reverse Scene Search .......... 23
J
JPEG ............................................ 45 ~ 47
K
Karaoke
(Vocal Selection for Karaoke Discs) ... 37
L
Language Code List ............................ 54
M
MENU button
(To display DVD Menu) ................. 8, 38
MP3 ...................................................... 45
Multiple Angle Viewing ........................ 37
Multi-channel speaker system ...... 15, 51
O
OPEN/CLOSE button ....................... 8, 22
Optical Digital Audio Output .......... 10, 15
Output Balance Setup ......................... 52
P
PAGE button (Still Image Skip) ....... 8, 41
PLAY button (Play a Disc) ............... 8, 22
Program Play (For Video CD/ CD) ...... 39
PROGRESSIVE button .......................... 9
Progressive Scan ................................. 10
R
Random Play (For Video CD/ CD) ...... 40
Repeat Play ......................................... 44
Resume Function ................................. 23
RETURN button ............................... 8, 22
Rotation ................................................ 47
S
SEARCH button
(Forward/Reverse Scene Search) .. 8, 23
SKIP
l
or
l
button
(Forward/Reverse Chapter/Track) 8, 23
Slide-show ........................................... 46
SLOW+/SLOW- button
(Slow Motion Picture) .................... 8, 23
Speaker Output Setup ......................... 51
Speaker Position ................................. 53
Speaker Size Setup ............................. 51
STILL button
(Still Picture or Pause) ................... 8, 23
Still Mode
(For selecting “FIELD” or “FRAME”) .. 53
STOP button ..................................... 8, 22
SUB TITLE button
(For selecting Subtitle Language) ... 8, 36
S-Video Out .................................... 10, 13
T
Test Signal Setup ................................ 53
TITLE button (Title Menu) ................ 8, 38
TV Mode
(For selecting the screen display style) .. 53
2-channel speaker system .............. 15, 51
V
Video CD ............................................. 23
VOLUME ADJUST button ................ 8, 40
V.S.S. (Virtual Surround Sound) ..... 8, 23
W
WMA ..................................................... 45
Z
ZOOM button (Picture Zoom) ..... 8, 37, 47
67
D4753S P36-60.p65
67 2003/03/13, 11:32
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094
Panasonic Sales Company (“PSC”),
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina,
Puerto Rico 00985
D4753S P36-60.p65
68 2003/03/13, 11:32
P
Printed in Indonesia
LSQT0675A
S0303-0
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 TABLE OF CONTENTS
- 2 IMPORTANT SAFEGUARDS AND PRECAUTIONS
- 4 BEFORE USING
- 7 INITIAL SETUP (CONNECTION)
- 6 DECK & CASSETTE INFORMATION
- 8 LOCATION OF CONTROLS
- 11 DISPLAYS (ON SCREEN & MULTI FUNCTION)
- 12 CONNECTIONS
- 16 INITIAL SETUP FOR BASIC CONNECTIONS (READY TO PLAY)
- 18 BASIC OPERATION
- 18 RESET LANGUAGE, CHANNELS, CLOCK, VCR'S OUTPUT CHANNEL
- 20 PLAYBACK/RECORD ON A TAPE
- 22 BASIC DVD OPERATION
- 24 VCR OPERATION
- 24 TIMER RECORDING
- 26 MTS BROADCAST / VHS HI-FI STEREO SYSTEM
- 28 MULTI-BRAND CONTROL FEATURE
- 30 TAPE OPERATION (SEARCH SYSTEM)
- 33 SPECIAL VCR FEATURES
- 35 COPYING YOUR TAPES (DUBBING)
- 36 DVD OPERATION
- 36 DISC OPERATON
- 42 DVD OPERATION USING ON-SCREEN DISPLAYS
- 45 MP3 / WMA / JPEG PLAYBACK OPERATION
- 48 DVD LOCK FEATURE
- 49 SETTINGS FOR DVD OPERATION
- 54 LANGUAGE CODE LIST
- 55 FOR YOUR INFORMATION
- 55 WARNING AND INSTRUCTION DISPLAYS
- 56 BEFORE REQUESTING SERVICE
- 58 LIMITED WARRANTY
- 59 CUSTOMER SERVICES DIRECTORY
- 60 SPANISH QUICK USE GUIDE / GUIA PARA RAPIDA CONSULTA
- 66 INDEX