Instruction manual Manuel d`instruction Manual de Instrucciones

PUB. DIM-1104-000A
Instruction manual
Manuel d'instruction
Manual de Instrucciones
C
Y
P
O
Español
Videocámera HD
Français
Caméscope HD
English
HD Camcorder
Important Usage Instructions
2
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE.
WARNING
TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING INTERFERENCE, USE THE
RECOMMENDED ACCESSORIES ONLY.
COPYRIGHT WARNING:
Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be
contrary to copyright laws.
The Mains plug is used as the disconnect device. The Mains plug shall remain readily operable to
disconnect the plug in case of an accident.
Y
P
O
CAUTION:
• Danger of explosion if the wrong type of batteries are attached. Use only the same type of batteries.
• Do not expose batteries or product to excessive heat such as the inside of a car under direct sunlight, fire, etc.
CA-930 identification plate is located on the bottom.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
C
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage”
within the product’s enclosure, that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point, within an equilateral triangle,
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
FCC NOTICE
HD Camcorder, XF200 / XF205 Systems.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual.
If such changes or modifications should be made, you could be required to stop operation of the
equipment.
Model ID0038 (including WLAN Module Model RF400, FCC ID: AZD400)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
The available scientific evidence does not show that any health problems are associated with using low
power wireless devices. There is no proof, however, that these low power wireless devices are absolutely
safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range
while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of lowlevel RF that does not produce heating effects causes no known adverse health effects. Many studies of
low-level RF exposures have not found any biological effects. Some studies have suggested that some
biological effects might occur, but such findings have not been confirmed by additional research. This model
has been tested and found to comply with FCC/IC radiation exposure limits set forth for an uncontrolled
equipment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio
frequency (RF) Exposure rules.
Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the
passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several
special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on
the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only
while one of the aforementioned packets is being transmitted. In other words, this device automatically
discontinues transmission in case of either absence of information to transmit or operational failure.
C
Frequency Tolerance: 25 ppm
Canon U.S.A., Inc.
One Canon Park, Melville, NY 11747, USA
Tel No. 1-800-OK-CANON (1-800-652-2666)
Y
P
O
3
English
Note: This equipment has been tested and found to comply with the limits for class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Important Safety Instructions
4
In these safety instructions the word “apparatus”
refers to the Canon HD Camcorder XF200 / XF205
and all its accessories.
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
8. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other.
A grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
9. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
10. Only use attachments/accessories specified by
the manufacturer.
11. Unplug this apparatus during lightning storms or
when unused for long periods of time.
12. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
Y
P
O
CAN ICES-3(B)/NMB-3(B)
C
REGIONS OF USE
XF200 / XF205 are in compliance (as of June 2014) with the radio signal regulations of the regions listed below. For
details on other regions where they can be used, make inquiries with the contacts listed on the back cover of this
instruction manual.
REGIONS
Canada, Hong Kong S.A.R., South Korea, Taiwan, USA
Model
ID0038: XF200 / XF205
5
English
Trademark Acknowledgements
• SD, SDHC and SDXC Logos are trademarks of SD-3C, LLC.
• CompactFlash is a trademark of SanDisk Corporation.
• The CF Logo is a trademark of CompactFlash Association.
• Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United
States and/or other countries.
• Apple, App Store, Mac OS, Final Cut Pro are trademarks of Apple Inc., registered in the U.S. and other
countries.
• IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.
• Google, Android, Google Play, are trademarks of Google Inc.
• Avid, Media Composer and NewsCutter are trademarks or registered trademarks of Avid Technology, Inc. or
its subsidiaries in the United States and/or other countries.
• Wi-Fi is a registered trademark of the Wi-Fi Alliance.
• Wi-Fi Certified, WPA, WPA2, and the Wi-Fi Certified logo are trademarks of the Wi-Fi Alliance.
• WPS as used on the camcorder's settings, onscreen displays and in this manual signifies Wi-Fi Protected
Setup.
• The Wi-Fi Protected Setup Identifier Mark is a mark of the Wi-Fi Alliance.
• JavaScript is a trademark or registered trademark of Oracle Corporation, its affiliates or subsidiaries in the
United States and other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
• Other names and products not mentioned above may be trademarks or registered trademarks of their
respective companies.
• This device incorporates exFAT technology licensed from Microsoft.
• ANY USE OF THIS PRODUCT OTHER THAN CONSUMER PERSONAL USE IN ANY MANNER THAT
COMPLIES WITH THE MPEG-2 STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED
MEDIA IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2
PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, L.L.C., 250 STEELE STREET,
SUITE 300, DENVER, COLORADO 80206.
• This product is licensed under AT&T patents for the MPEG-4 standard and may be used for encoding MPEG4 compliant video and/or decoding MPEG-4 compliant video that was encoded only (1) for a personal and
noncommercial purpose or (2) by a video provider licensed under the AT&T patents to provide MPEG-4
compliant video. No license is granted or implied for any other use for MPEG-4 standard.
C
Y
P
O
Highlights of the XF200 / XF205
The Canon HD Camcorder XF200 / XF205 is a compact-sized and highly portable camcorder that offers
superior video quality. The camcorder features a 1/2.84-in. CMOS sensor and allows you to record in two
formats (MXF on CF cards or MP4 on SD cards). The following are some of the many features that will help you
turn your creative vision into reality.
6
HD Recording
1/2.84-in. CMOS sensor and DIGIC DV 4 image
processor
The HD CMOS PRO sensor can capture video at an
effective pixel count of 2,910,000 pixels. Combined
with the advanced DIGIC DV 4 image processor and
the 20x wide-angle lens, it can deliver a center
resolution of 900 TV lines. Furthermore, thanks to
Canon’s high-sensitivity and noise reduction
technologies, you can get excellent video quality
with minimal noise even when recording in low-light
situations.
MXF and MP4 formats
You can choose the movie format according to your
workflow needs. You can record in MXF format
using the MPEG-2 Long GOP codec, in MP4 format
using the MPEG-4 AVC/H.264 codec, or in both
formats simultaneously. MXF clips are recorded as
Material eXchange Format (MXF files), compatible
with all major non-linear (NLE) editing software.
C
Flexible video and audio configuration
For MXF clips, the camcorder offers 3 resolution
sizes (1920x1080, 1440x1080 or 1280x720), 4
frame rate options and 3 bit rate options for a total
of 16 video configurations (A 55). Audio is
recorded as linear PCM audio using 2 or 4 channels
(A 98).
For MP4 clips, the camcorder offers 3 resolution
sizes (1920x1080, 1280x720 or 640x360), 3 frame
rate options and 5 bit rate options for a total of 8
possible video configurations (A 55).
Improved displays
The camcorder features a 3.5-in. OLED display
(equivalent to 1,230,000 dots) that excels in color
reproduction, contrast and responsiveness and is
easy to use even in bright outdoors. The viewfinder,
on the other hand, offers a high-resolution LCD
screen (also equivalent to 1,230,000 dots) with a
wide angle of view of approx. 28.2°. The viewfinder
can be tilted 68° vertically to ensure a comfortable fit
in various shooting conditions.
Recording media
The camcorder records MXF clips to CF cards and
MP4 clips to SD cards. It features two CF card slots
that you can use to record continuously, one after
the other, using relay recording (A 42), or
simultaneously using double slot recording (A 42).
You can even record MP4 clips to the SD card while
recording an MXF clip on one or both CF cards
(A 123).
Y
P
O
Work with major NLE software
The Canon XF Utility software and various XF
plugins are available as free downloads from your
local Canon Web site. Canon XF Utility allows you
to easily save, manage and play back your MXF
clips, while the XF plugins let you smoothly link them
to major NLE software* to continue your editing
workflow. For details, refer to Saving MXF Clips
(A 168).
The supplied software Data Import Utility allows
you to save MP4 clips to a computer and even join
split MP4 files into a single file for editing. For details,
refer to Saving MP4 Clips (A 170).
* Refer to Saving Clips to a Computer (A 168) for details
on compatible software.
Operability and Adaptability
Freely customizable compact design
The camcorder offers maximum operability for a
single camera operator. It features 3 separate rings
for independent focus, zoom and iris operation. The
camcorder’s side grip can be easily adjusted up to
120 degrees to let you use whatever camera angle
you need (A 35). Additionally, gain, shutter and iris
controls can be adjusted manually or automatically
giving you the freedom to decide to what extent you
want to control every aspect of the image.
Pro-level remote operation
The camcorder can be used with the optional
RC-V100 Remote Controller for remote operation of
many advanced functions, including iris, gain and
even custom picture settings.
Versatile Artistic Expression
Custom picture settings
With custom picture settings (A 132), you can
enjoy unparalleled image control to deliver the “look”
you want by adjusting parameters, such as gamma
and sharpness.
Advanced Professional Features and
Flexibility
Wired and Wi-Fi network functions (A 173)
You can connect the camcorder to other devices via
wired (Ethernet) connection or Wi-Fi to enjoy a
variety of functions. For example, you can transfer
recordings to an FTP server or use the Web browser
on a connected device to remotely operate the
camcorder (Browser Remote) or to play back the
recordings on the camcorder (Playback via
Browser).
• Direct setting mode (A 57)
Change main camera functions while checking
the image on the screen using only the joystick.
• Assistance functions
Peaking and magnification (A 84) can be helpful
when you use manual focus, onscreen markers
(A 88) can be very useful to help you frame your
video, and zebra patterns (A 89) can give you a
reference point to avoid overexposures.
• Video scopes (A 108)
Check the brightness of the image using the
waveform monitor, the color of the image using
the vectorscope, or the focus using the edge
monitor.
• Intelligent System
When using battery packs compatible with
Intelligent System, the camcorder will display an
estimate, in minutes, of the remaining recording/
playback time using the battery pack (A 25). You
can also check the battery life indicator and other
information on the [Battery/Hour Meter] status
screen (A 213).
Y
P
O
Pro-level connectivity
The camcorder offers two terminals for professional
level connectivity. Use the 3G/HD-SDI terminal to
output the uncompressed HD video signal along
with embedded audio and SMPTE time code (LTC)
in a format that can be used for external recording.
Meanwhile, the MON. terminal offers the best video
output for an external monitor, including the option
to overlay the camcorder’s onscreen displays.
Genlock synchronization (A 94), the TIME CODE
terminal (A 95, 96) and GENLOCK/SYNC OUT
terminal allow the camcorder to be part of any multicamera shooting setup.
C
Other Functions
Infrared recording
Record in darkness using infrared recording
(A 126). With the built-in infrared light, you can
record nocturnal animals in their natural environment
or other such scenes.
Customization
The camcorder features several customization
options. You can assign often-used functions to
assignable buttons (A 129) so that you can call up
those functions with the press of a single button.
You can also register frequently-used menu settings
in an easy-to-access personal menu (My Menu,
A 30). Custom functions (A 141) and custom
onscreen displays (A 142) give you even more
freedom to control many aspects of the camcorder’s
• Multiple audio recording options (A 98)
The camcorder offers 2- or 4-channel linear PCM
audio recording for MXF clips and 2-channel AAC
audio recording for MP4 clips. You can use the
camcorder’s built-in microphone, external
microphones with a ∅ 3.5 mm mini-stereo plug
(MIC terminal), or external audio input sources
with an XLR plug (INPUT 1/INPUT 2 terminals with
+48 V phantom power supply). The camcorder
even has a convenient microphone holder with
cable clamp for external microphones.
• Metadata and GPS information (A 111, 114)
You have the option to add various metadata
fields to your MXF clips. Some of the information
requires using Canon XF Utility or the Browser
Remote application. Additionally, you can connect
the optional GP-E2 GPS Receiver to the
camcorder to automatically add GPS information
to your recordings. Using Canon XF Utility you
can then organize or search MXF clips by GPS
information.
7
English
Special recording modes
The special recording modes (A 118) give you
more creative control over your recordings. You can
create a slow motion or fast motion effect in your
recordings, record a certain number of frames at a
set interval (ideal for nature shots and other subjects
with little movement) or record a certain number of
frames every time you press a button (ideal for stop
motion animation).
operation. Save custom picture and menu settings
to an SD card so that you can transfer your setting
preferences to other XF200 / XF205 camcorders in
order to use them in the same way.
Table of Contents
8
1. Introduction 11
Remote Operation of the Camcorder 44
Using the Supplied Wireless Controller 44
Using the Optional RC-V100 Remote
Controller 45
About this Manual 11
Conventions Used in this Manual 11
Supplied Accessories 13
Names of Parts 14
WL-D6000 Wireless Controller 21
3. Recording 47
2. Preparations 23
Preparing the Power Supply 23
Using a Battery Pack 23
Using a Household Power Outlet 25
Turning the Camcorder On and Off 26
Date, Time and Language Settings 27
Setting the Date and Time 27
Changing the Time Zone 27
Displaying the Date and Time while Recording 28
Changing the Language 28
Using the Menus 29
Selecting an Option from the Menu 29
Using the Customized Submenu (My Menu) 30
Preparing the Camcorder 32
Attaching the Microphone Holder Unit 32
Attaching the Lens Hood 32
Using the Viewfinder 32
Using the OLED Panel 33
Adjusting the Viewfinder/OLED Screen 34
Adjusting the Color Balance of the OLED
Screen 34
Setting the Screen to Black & White 35
Adjusting the Grip Unit 35
Attaching the Shoulder Strap 36
Removing and Attaching the Terminal Covers 36
Using a Tripod 37
Preparing Recording Media 38
Inserting a CF Card 39
Checking the Status of the CF Card Slots 39
Removing a CF card 40
Inserting and Removing an SD Card 40
Initializing the Recording Media 41
Switching Between the CF Card Slots 41
Selecting the CF Card Recording Method 42
Checking the Available Recording Time on a
Recording Media 43
Recovering Data on a Recording Media 43
C
Recording Video 47
Preparing to Record 47
Recording 48
Remote Operation Using Browser Remote 50
Onscreen Displays 51
Power Save Mode 54
Using the Fan 54
Video Configuration: Movie Format, Bit Rate,
Resolution and Frame Rate 55
Changing Main Camera Functions with the
Joystick 57
Using the Direct Setting Mode 57
Shutter Speed 58
Automatic Shutter 59
Manual Shutter 60
Flicker Reduction 61
Gain 62
Selecting the Gain Level 62
Automatic Gain Control (AGC) 62
Manual Gain 63
Aperture 65
Automatic Aperture 65
Manual Aperture 66
ND Filter 67
Exposure Compensation - AE Shift 67
Light Metering Mode 68
White Balance 69
Auto White Balance (AWB) 70
Preset White Balance/Color Temperature 71
Custom White Balance 72
Zooming 74
Selecting the Zoom Mode 74
Using the Zoom Ring 75
Using the Zoom Rockers on the Camcorder 75
Remote Operation 78
Soft Zoom Control 79
Using Optional Conversion Lenses 80
Y
P
O
C
Special Recording Modes 118
Interval Recording Mode 118
Frame Recording Mode 119
Slow & Fast Motion Mode 120
Pre-recording Mode 121
Simultaneous Recording of MXF and MP4
Clips 123
Recording in MP4 Backup Recording Mode 124
Infrared Recording 126
Activating Infrared Mode 126
Using the Infrared Light 126
Using the Focal Length Guide 128
4. Customization 129
Assignable Buttons 129
Changing the Assigned Function 129
Using an Assignable Button 130
Custom Picture Settings 132
Selecting Custom Picture Files 132
Editing a Custom Picture File’s Settings 133
Renaming Custom Picture Files 133
Protecting Custom Picture Files 133
Transferring Custom Picture Files 134
Embedding Custom Picture Settings in a
Recording 135
Available Custom Picture Settings 135
Customizing Functions and Onscreen
Displays 141
Customizing Functions 141
Customizing Onscreen Displays 142
Saving and Loading Camera Settings 143
Saving Camera Settings to an SD Card 143
Loading Camera Settings from an SD Card 143
Y
P
O
5. Playback 145
Playback 145
MXF and MP4 Clip Index Screens 145
Playing Back Clips 147
Onscreen Displays 147
Playback Controls 148
Adjusting the Volume 149
9
English
Adjusting the Focus 81
Autofocus (AF) Mode 81
Manual Focus (MF) 83
Push AF 85
Detecting and Focusing On Faces 85
Focus Limit and Macro Shooting 86
Image Stabilizer 87
Onscreen Markers and Zebra Patterns 88
Displaying Onscreen Markers 88
Displaying Zebra Patterns 89
Setting the Time Code 90
Selecting the Running Mode 90
Selecting Drop or Non-Drop Frame 91
Putting the Time Code Display on Hold 91
Setting the User Bit 93
Synchronizing with an External Device 94
Connecting an External Device 94
Reference Video Signal Input (Genlock
Synchronization) 94
Time Code Signal Input 95
Reference Video Signal Output 96
Time Code Signal Output 96
Recording Audio 98
Audio Settings and Recorded Audio Channels 98
Selecting the Number of Recorded Audio
Channels 100
Connecting an External Microphone or External
Audio Input Source to the Camcorder 100
Using the Built-in Microphone or MIC
Terminal 101
Using the INPUT 1/INPUT 2 Terminals 103
Adjusting the Audio Level 105
Monitoring the Audio with Headphones 106
Colors Bars/Audio Reference Signal 107
Recording Color Bars 107
Recording an Audio Reference Signal 107
Video Scopes 108
Displaying a Video Scope 108
Configuring the Waveform Monitor 108
Configuring the Vectorscope 109
Configuring the Edge Monitor 109
Adding Marks to MXF Clips while Recording 110
Adding Shot Marks while Recording 110
Adding an $ Mark or % Mark to the Last Clip
Recorded 110
Using Metadata 111
Setting a User Memo Created with Canon XF
Utility 111
Setting a User Memo Using Browser
Remote 112
Recording GPS Information (Geotagging) 114
Reviewing a Recording 116
File Numbering 117
10
Clip Operations 150
Using the Clip Menu 151
Displaying Clip Information 151
Adding $ Marks or % Marks 152
Deleting $ Marks or % Marks 153
Copying Clips 153
Deleting Clips 154
Deleting the User Memo and GPS
Information 155
Copying a Custom Picture File Embedded in a
Clip 155
Displaying an Index Screen of Shot Marks 155
Displaying a Frame Index Screen of a Single
Clip 156
Adding Shot Marks 157
Deleting Shot Marks 157
Changing a Clip’s Thumbnail 158
6. External Connections 159
Video Output Configuration 159
Recording Video Signal Configuration and Video
Output Configuration by Terminal 159
Playback Video Configuration and Video Output
Configuration by Terminal 160
Connecting to an External Monitor 162
Connection Diagram 162
Using the 3G/HD-SDI Terminal 163
Using the MON. Terminal 163
Using the HDMI OUT Terminal 164
Using the AV OUT Terminal 164
SD Output 165
Superimposing Onscreen Displays to Appear on
an External Monitor 165
Audio Output 166
Selecting the Audio Channel 166
Synchronizing the Video with the Audio being
Monitored 167
Selecting the Output Level of the AV OUT
Terminal 167
Saving Clips to a Computer 168
Saving MXF Clips 168
Saving MP4 Clips 170
Connecting the Camcorder to a Computer 171
C
7. Network Functions 173
About the Network Functions 173
Connecting to a Wi-Fi Network 174
Wi-Fi Protected Setup (WPS) 174
Searching for Access Points 175
Manual Setup 177
Camera Access Point 177
Configuring the IP Address Settings 178
Saving the Configuration 178
Connecting to a Wired (Ethernet) Network 179
Selecting a Network Connection 180
Changing Network Settings 181
Browser Remote: Controlling the Camcorder from
a Network Device 182
Setting Up Browser Remote 182
Starting Browser Remote 183
Real-Time Proxy Transfer 188
FTP File Transfer 189
Preparations 189
FTP Transfer in
Mode 190
FTP Transfer in
Mode 191
Playback via Browser 193
8. Photos 195
Taking Photos 195
Taking Photos in
Mode 195
Capturing Photos in
Mode 195
Photo Playback 197
Displaying the [Photos] Index Screen 197
Viewing Photos 197
Deleting Photos 198
Y
P
O
9. Additional Information 199
Menu Options 199
Displaying the Status Screens 209
Troubleshooting 218
List of Messages 223
Handling Precautions 228
Maintenance/Others 231
Optional Accessories 232
Specifications 235
Index 241
1
Introduction
11
About this Manual
Conventions Used in this Manual
•
IMPORTANT: Precautions related to the camcorder’s operation.
•
NOTES: Additional topics that complement the basic operating procedures.
• A: Reference page number.
•
: Text that applies only to the model shown in the icon.
• The following terms are used in this manual.
“Screen” refers to the OLED screen and the viewfinder screen.
“CF card” refers to a CompactFlash (CF) card.
“SD card” refers to an SD, SDHC or SDXC memory card.
“Recording media” refers to CF cards and SD cards.
When not specified, “access lamps” refers to either or both of the CF card access lamps (CF2/CF3) and the
SD card access lamp.
“Press SET” refers to pressing down the joystick itself (A 29).
• Photographs in the manual are simulated pictures taken with a still camera. Some screenshots have been
altered to make them easier to read.
• Illustrations in the manual show the XF205.
C
Y
P
O
English
Thank you for purchasing the Canon XF200 / XF205. Please read this manual carefully before you use the
camcorder and retain it for future reference. Should the camcorder fail to operate correctly, refer to
Troubleshooting (A 218).
About this Manual
12
The arrow > is used to abbreviate menu
selections. For a detailed explanation on how to
use the menus, refer to Using the Menus
(A 29). For a concise summary of all available
menu options and settings, refer to the appendix
Menu Options (A 199).
C
When a procedure requires selecting an option,
the available options are listed within or after the
procedure. Brackets [ ] are used to refer to menu
options as they are displayed on screen.
Operating modes and Format
A full icon (like
) indicates that the function
described can be used in the operating mode
shown or for recordings made in the movie
format shown in the icon; an empty icon (like
) indicates that the function cannot be
used. For details refer to Turning the Camcorder
On and Off (A 26) or Selecting the Movie
Format (A 55).
Y
P
O
When a function requires the use of the menu,
the quick reference shows the submenus and,
when applicable, the default setting for the menu
item. The example illustration indicates that you
can find the function by selecting the
[w Other Functions] menu and then the [Fan]
menu item.
Supplied Accessories
Supplied Accessories
The following accessories are supplied with the camcorder.
13
English
CA-930 Compact Power Adapter
(incl. power cord)
DC-930 DC Cable
Lens Hood with Lens Barrier
Lens Cap
Eye cup
Microphone Holder Unit
SS-1200 Shoulder Strap
C
WL-D6000 Wireless Controller
(incl. CR2025 Lithium Battery)
Y
P
O
BP-955 Battery Pack
(incl. terminal cover)
Data Import Utility
Software CD-ROM*
* The Data Import Utility Software Guide (PDF file) is included in the CD-ROM. For details about the software, refer to this Software
Guide.
Names of Parts
Names of Parts
1
14
Operation panel 햲
8
9
(A 20)
2 3 4
10
5
6
7
11
12
13 14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
C
Y
P
O
Operation panel 햳
(A 20)
18 20 22 24 26
15 16 17 19 21 23 25 27 28
Protective cover for audio controls (A 98)
Strap mount (A 36)
INFRARED switch (A 126)
ZOOM SPEED (zoom speed of the handle's zoom
rocker) switch (A 75)
CF card slot covers for CF card slots A (left) and B
(right)
POWER SAVE button (A 54)
Exhaust ventilation outlet (A 54)
CF2 (CF card slot A) and CF3 (CF card slot B)
access indicators (A 39)
CF card release buttons for CF card slots A (left)
and B (right) (A 40)
CF card slots A (left) and B (right) (A 39)
Q switch (A 26)
Power indicator (A 26)
Lens hood (A 32)
Lens barrier switch (A 47)
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Focus ring (A 83)
Zoom ring (A 75)
Iris ring (A 66)
PUSH AF (momentary autofocus) button (A 85)
IRIS (ND) (aperture mode/ND filter) switch (A 65)
FOCUS (focus mode) switch (A 81, 83)
PEAKING button (A 84) /
Assignable button 1 (A 129)
ZEBRA button (A 89)/
Assignable button 2 (A 129)
FULL AUTO switch (A 49)
CF card slot cover switches for CF card slots A
(left) and B (right) (A 39)
SHUTTER switch (A 58)
GAIN switch (A 62)
WHITE BAL. (white balance) switch (A 69)
Å (white balance adjustment) button (A 72)
Names of Parts
33
34
35 36
37
15
English
38
29
30
31
32
29
30
31
32
33
34
C
Y
P
O
GENLOCK/SYNC OUT (synchronization)
terminal (A 94, 96)
TIME CODE terminal (A 95, 96)
MON. (monitor output) terminal (A 162,
163)
3G/HD-SDI terminal (A 162, 163)
Strap mount (A 36)
REMOTE terminal (A 45)
For connecting the optional RC-V100 Remote
Controller or commercially available remote
controllers.
39
40
41
42
35 USB terminal (A 171)
36 MIC (microphone) terminal (A 101)
37 Attachment sockets for the microphone holder
unit (A 32)
38 INPUT 1 (right) and INPUT 2 (left) terminals (XLR)
(A 103)
39 Air intake vent (A 54)
40 Grip belt (A 35)
41 Adjustable grip unit (A 35)
42 Lens hood lock screw (A 32)
Names of Parts
43
16
44
48
45
49
50
51
46
47
43
44
45
46
47
Microphone lock screw (A 100)
Microphone holder (A 100)
Microphone cable clamp (A 100)
Lens barrier (A 47)
Instant AF sensor (A 81)
C
Y
P
O
48
49
50
51
52
52
Built-in stereo microphone (A 101)
Front tally lamp (A 48)
Remote sensor (A 44)
Infrared light (A 126)
START/STOP button (A 48, 123)
Names of Parts
61
62
English
53
54
17
63
64
65
55
56
66
67
57
58
59
60
C
Y
P
O
68
69
70
71
72
73
53
54
55
56
57
58
59
60
61
62
MENU button (A 29)
Joystick (A 29)/SET button (A 29)
CANCEL button (A 29)
POWERED IS button (A 87)/
Assignable button 3 (A 129)
OLED screen (A 33, 34)
SD card slot cover (A 40)
SD card access indicator (A 48, 123, 195)
SD card slot (A 40)
Viewfinder (A 32, 34)
Eye cup (A 33)
63
64
65
66
67
68
69
70
71
72
73
Dioptric adjustment lever (A 33)
Viewfinder unit
Battery compartment (A 24)
START/STOP button (A 48, 123)
UNLOCK (unlock the grip) switch (A 35)
× (headphone) terminal (A 106)
AV OUT terminal (A 162, 164)
HDMI OUT terminal (A 162, 164)
DC IN terminal (A 25)
LAN access indicator (A 179)
LAN terminal (Ethernet) (A 179)
Names of Parts
74
75
76 77
78
79
80
81
18
82
83 84 85
C
74 Accessory shoe
For attaching accessories such as the optional
VL-10Li II Battery Video Light.
75 Built-in speaker (A 149)
76 START/STOP lock lever (A 48)
77 START/STOP button (A 48, 123)
78 Grip zoom rocker (A 75)
79 MAGN. (magnification) button (A 84)/
Assignable button 4 (A 129)
Y
P
O
86
80
81
82
83
Strap mount (A 36)
BATTERY RELEASE lever (A 24)
Front tally lamp (A 48)
– dials for CH1 (left) and CH2 (right)
(A 105)
84 Rear tally lamp (A 48)
85 Handle zoom rocker (A 77)
86 Handle socket for 1/4" screws
Names of Parts
87
19
English
88
C
89
Y
P
O
90
87 Attachment sockets for the optional TA-100 Tripod
Adapter (A 37)
88 Tripod base screws (A 37)
91
89 Tripod base for tripods with 1/4" screws (A 37)
90 Air intake vent (A 54)
91 Tripod socket (A 37)
Names of Parts
Operation panels
Operation panel 햲
Operation panel 햳
1
20
4
5
2
3
1
2
3
4
5
6
7
Audio level switches for CH1 (left) and CH2 (right)
(A 105)
AUDIO IN (audio input) selection switches for CH1
(left) and CH2 (right) (A 101, 103)
INPUT 1 (left) / INPUT 2 (right) audio source
selection switches (A 103)
Ò (play/pause) button (A 147)/
Assignable button 6 (A 129)
Ø (fast reverse playback) button (A 148)/
Assignable button 5 (A 129)
Ú (skip backward) button (A 148)/
Assignable button 8 (A 129)
SLOT SELECT (CF card slot selection) button
(A 41, 146)
C
8
9
6
11
12
7
8
13
9
14
15
INDEX button (A 146)/
u (review recording) button (A 116)
HEADPHONE+ button (A 149)/
Assignable button 11 (A 129)
× (fast playback) button (A 148)/
Assignable button 7 (A 129)
Ù (skip forward) button (A 148)/
Assignable button 10 (A 129)
Ñ (stop) button (A 147)/
Assignable button 9 (A 129)
DISP. (display) button (A 51, 147)
WFM (waveform monitor) button (A 108)/
Assignable button 13 (A 129)
HEADPHONE- button (A 149)/
Assignable button 12 (A 129)
Y
P
O
10
11
12
13
14
15
10
Names of Parts
WL-D6000 Wireless Controller
9
10
6
7
12
8
13
11
14
1
2
3
4
5
6
7
Y
P
O
Record enable button: When you use the START/
STOP button or ZOOM buttons, you must press
this button simultaneously with the desired button.
PHOTO button (A 195)
SHOT1 (shot mark 1) button (A 157)
CANCEL button (A 29)
SET button (A 29)
INDEX button (A 146)
Ò (play/pause) button (A 148)
C
Ñ (stop) button (A 148)
START/STOP button (A 48, 123)
ZOOM buttons (A 78)
Í/Î/Ï/Ð buttons
MENU button (A 29)
Ø/× (fast playback reverse/forward) buttons
(A 148)
14 Ô/Ó (frame reverse/frame forward) buttons
(A 148)
8
9
10
11
12
13
English
1
2
3
4
5
21
Names of Parts
22
C
Y
P
O
2
Preparations
23
Preparing the Power Supply
Using a Battery Pack
You can power the camcorder using the supplied BP-955 or an optional BP-950G, BP-970G or BP-975 Battery
Pack. The BP-955 and BP-975 are compatible with Intelligent System, meaning that you can check the
remaining battery time.
Charging the Battery Pack
Y
P
O
Charge battery packs using the supplied CA-930 Compact Power Adapter.
Before charging, remove the terminal cover of the battery pack.
1 If the DC cable is connected to the compact power adapter, disconnect
it.
• If the DC cable is connected to the compact power adapter, charging
will not start.
C
2 Connect the power cord to the compact power adapter.
3 Plug the power cord into a power outlet.
햵
햳
햲
CHARGE indicator
4 Attach the battery pack to the compact power adapter.
햴
• Press lightly and slide the battery pack in the direction of the arrow until it
clicks.
• The CHARGE indicator starts flashing and also indicates the battery pack’s approximate charge. The
indicator will stay on when charging has completed.
0-34%: Flashes once per second
35-69%: Flashes twice per second
70-99%: Flashes 3 times per second
5 When charging has completed, remove the battery pack from the compact power adapter.
6 Unplug the power cord from the power outlet and disconnect it from the compact power adapter.
IMPORTANT
• Do not connect to the compact power adapter any product that is not expressly recommended for use with this
camcorder.
NOTES
• We recommend charging the battery pack in temperatures between 10 ºC and 30 ºC (50 ºF and 86 ºF).
Outside the temperature range of 0 ºC to 40 ºC (32 ºF to 104 ºF), charging will not start.
• To charge the battery pack, disconnect the DC cable from the compact power adapter.
English
You can power the camcorder using a battery pack or directly using the compact power adapter. If you connect
the compact power adapter to the camcorder while a battery pack is attached, the camcorder will draw power
from the power outlet.
Charge battery packs before use. For approximate charging times and recording/playback times with a fully
charged battery pack, refer to Charging Times (A 233) and Recording and Playback Times (A 233).
Preparing the Power Supply
24
• If there is a malfunction with the compact power adapter or battery pack, the charge indicator will go out and
charging will stop.
• For handling precautions regarding the battery pack, refer to Battery Pack (A 228).
• Charged battery packs continue to discharge naturally. Therefore, charge them on the day of use, or the day
before, to ensure a full charge.
• Repeatedly charging and discharging the battery pack will eventually shorten its battery life. You can check the
battery life on the [Battery/Hour Meter] status screen (A 213). Fully charging the battery pack and then
discharging it will give you a more accurate reading.
• We recommend that you prepare battery packs to last 2 to 3 times longer than you think you might need.
Attaching the Battery Pack
햲
1 Set the Q switch to OFF.
2 Insert the battery pack all the way into the compartment and
press gently down until it clicks.
Y
P
O
햳
Removing the Battery Pack
1 Set the Q switch to OFF.
C
햲
2 Slide the BATTERY RELEASE lever in the direction of the arrow.
While holding it pressed down, slide the battery pack up and
remove it from the battery compartment.
햳
Preparing the Power Supply
Checking the Remaining Battery Charge
With battery packs compatible with Intelligent System, you can check the estimated remaining usage time of the
battery pack by looking at any recording/playback screen or the [Battery/Hour Meter] status screen (A 213).
You can also check the approximate remaining battery charge on the battery pack itself.
0-25%
26-50%
51-75%
76-100%
CHECK button
0
100%
Battery charge indicator
NOTES
• The first time you use a battery pack, charge it fully and then use the camcorder until the battery pack is
completely exhausted. Doing so will ensure that the remaining recording time will be displayed accurately.
• USA and Canada only: The Lithium ion/polymer battery that powers the product is recyclable.
Please call 1-800-8-BATTERY for information on how to recycle this battery.
C
Using a Household Power Outlet
Y
P
O
You can also power the camcorder directly from a power
outlet using the supplied CA-930 Compact Power Adapter
and DC-930 DC Cable. While the camcorder is powered
from a household power outlet, you can safely replace the
battery pack even when the camcorder is on.
햲
1 Set the Q switch to OFF.
2 Connect the DC cable to the DC IN terminal on the
camcorder.
3 Connect the power cord to the compact power adapter
and plug it into a power outlet.
햴
4 Connect the DC cable to the compact power adapter.
IMPORTANT
• Turn off the camcorder before connecting or
disconnecting the compact power adapter.
DC IN
terminal
25
English
Press the CHECK button on the battery pack. An indicator will light for
approximately 3 seconds and show the approximate remaining battery
charge.
햳
햵
Preparing the Power Supply
Turning the Camcorder On and Off
The camcorder has two operating modes: CAMERA (
) mode for making recordings and MEDIA (
mode for playing back recordings. Select the operating mode using the Q switch.
26
To turn on the camcorder
Hold down the button on the Q switch and slide the switch to
CAMERA for
mode or MEDIA for
mode. The power indicator
will illuminate in green.
CAMERA mode
MEDIA mode
To turn off the camcorder
Set the Q switch to OFF. The power indicator will turn off.
Y
P
O
NOTES
• If you set the [w Other Functions] > [POWER LED] setting to [Off], the power indicator will not illuminate.
C
)
Date, Time and Language Settings
Date, Time and Language Settings
Setting the Date and Time
You will need to set the date and time of the camcorder before you can start using it. When the camcorder’s
clock is not set, the [Date/Time] screen will appear automatically with the month selected.
English
Operating modes:
27
1 Push the joystick up/down to change the month then move (Ð) to the next field.
• To move to the next field you can also press the joystick itself.
2 Change the rest of the fields in the same way.
Y
P
O
3 Select (Ð) [Set] and then press the joystick to start the clock and close the screen.
NOTES
• You can change the date format and the clock format (12/24 hours) with the [w Other Functions] >
[Set Clock] > [Date Format] setting. You can also change the date and time later on (not during the initial
setup) with the [w Other Functions] > [Set Clock] > [Date/Time] setting. However, while the camcorder is
being operated through the Browser Remote application, the [Set Clock] submenu is not available.
• When the built-in rechargeable lithium battery is exhausted, the date and time setting may be lost. In such
case, recharge the built-in lithium battery (A 230) and set the time zone, date and time again.
• Using the optional GP-E2 GPS Receiver, you can have the camcorder adjust settings automatically according
to the UTC date/time information received from the GPS signal (A 114).
C
Changing the Time Zone
Change the time zone to match the time zone of your location. The default
setting is [UTC-05:00 New York]. The time zones are based on
Coordinated Universal Time (UTC).
Operating modes:
[w Other Functions]
[Time Zone]
[UTC-05:00 New York]
1 Press the MENU button.
2 Push the joystick up/down to select [w Other Functions].
3 Select [Time Zone] in a similar fashion.
4 Push the joystick up/down to change the time zone.
5 Press the joystick to set the time zone and then press the MENU button to close the menu.
NOTES
• While the camcorder is being operated through the Browser Remote application, the [Time Zone] setting is not
available.
Date, Time and Language Settings
Displaying the Date and Time while Recording
You can display the date and time on the screen.
28
[£ OLED/VF Setup]
[Custom Display 2]
Operating modes:
[Date/Time]
1 Press the MENU button.
2 Push the joystick up/down to select [£ OLED/VF Setup].
[Off]
3 Select [Custom Display 2] and then [Date/Time] in a similar
fashion.
4 Push the joystick up/down to select the information to display.
• Select [Off] to record without displaying the date and time.
5 Press the joystick and then press the MENU button to close the menu.
• The selected date/time display will appear at the bottom of the screen.
Changing the Language
Y
P
O
The default language of the camcorder is English. You can change it to
German, Spanish, French, Italian, Polish, Portuguese, Russian, Simplified
Chinese, Korean or Japanese. Please note that some settings and
screens will be displayed in English, regardless of the language setting.
Operating modes:
1 Press the MENU button.
C
[w Other Functions]
[Language !]
[English]
2 Push the joystick up/down to select [w Other Functions].
3 Select [Language !] in a similar fashion.
4 Push the joystick up/down to select a language.
5 Press the joystick to change the language and then press the MENU button to close the menu.
Using the Menus
Using the Menus
Operating modes:
MENU button
Joystick
CANCEL button
Y
P
O
MENU button
Press to open the menu and then press again to close the menu after adjusting desired settings.
Joystick
Push the joystick to move the orange selection frame in the menu. Then, press the joystick itself to select the
menu item indicated by the orange selection frame.
C
CANCEL button
Press to return to the previous menu or to stop some operations that are in progress.
NOTES
• Although the button at the center of the joystick is not labeled as SET, in the manual, “press SET” will be used
to mean pressing down the joystick itself.
Selecting an Option from the Menu
The following is a step-by-step explanation of how to select an option from the menu. In the procedures
throughout the rest of this manual, opening and closing the menu is assumed and not included in the procedure.
1 Press the MENU button.
• The menu opens with the orange selection frame indicating the menu item that was selected the previous
time the menu was closed (unless the camcorder was turned off).
2 Push the joystick up/down to select the desired submenu.
3 Push the joystick right or press SET.
• The orange selection frame will appear on a menu item in the submenu.
• Press the CANCEL button, push the joystick left, or select [L] to return to the previous submenu.
4 Push the joystick up/down to select the desired menu item.
• If a submenu contains many menu items, a scroll bar will appear on the right side of the submenu indicating
that you must scroll up or down to see other menu items.
• A Ð mark next to a menu item indicates another submenu. Repeat steps 3 and 4.
29
English
In
mode, many of the camcorder’s functions can be adjusted from the menu for general settings, which
opens after pressing the MENU button. You can also register frequently used menu settings in a customized
submenu (My Menu) for easy access. In
mode, press the MENU button to open the menu for general
settings or press the joystick to open the clip menu for clip operations. For details about the available menu
options and settings, refer to Menu Options (A 199).
Using the Menus
5 Push the joystick right or press SET.
• The orange selection frame will appear on a setting option.
• Press the CANCEL button to return to the previous submenu.
30
6 Push the joystick up/down to select the desired setting option and then press SET.
• Depending on the menu item, additional selections may be necessary.
7 Press the MENU button to close the menu.
NOTES
• Unavailable items may appear grayed out.
• Pressing the MENU button at any time closes the menu.
• On some screens, the following icons may be displayed as a guide:
,
,
. They refer, respectively,
to pressing the joystick (or SET button on a remote control), the MENU button or the CANCEL button.
• When using the supplied wireless controller, use the á, â, à, ß and SET buttons in the same way as the
camcorder’s joystick. Similarly, when using the optional RC-V100 Remote Controller, use the Up, Down, Left,
Right and SET buttons. In either case, pressing the SET button is equivalent to pressing the joystick on the
camcorder.
• You can check some of the current settings on the status screens (A 209).
Y
P
O
Using the Customized Submenu (My Menu)
You can register up to 14 frequently used menu settings under the My Menu submenu for easy access.
Furthermore, if you set an assignable button to [My Menu] (A 129), you can press the button to access your
registered menu settings even faster and more easily.
Operating modes:
Adding Menu Settings
C
1 Open the My Menu [Register] screen.
[¥ My Menu] > [Edit] > [Register]
• The menu will change to blue to indicate you are selecting menu
settings to add to the My Menu submenu.
• Press the CANCEL button to cancel the operation and return to the
regular menu.
2 Navigate the menus to find the menu setting you want to add and then press SET.
3 Select [OK] and then press SET twice.
• The menu setting you registered will now appear under the My Menu submenu.
[¥ My Menu]
[Edit]
[Register]
Using the Menus
Rearranging Menu Settings
[¥ My Menu]
1 Open the My Menu [Move] screen.
[¥ My Menu] > [Edit] > [Move]
[Edit]
3 Push the joystick up/down to move the setting to the desired position and then press SET.
Removing Menu Settings
[¥ My Menu]
1 Open the My Menu [Delete] screen.
[¥ My Menu] > [Edit] > [Delete]
2 Push the joystick up/down to select the setting you want to remove and
then press SET.
3 Select [OK] and then press SET twice.
Resetting the My Menu Submenu
Y
P
O
1 Reset all the menu settings registered to the My Menu submenu.
[¥ My Menu] > [Edit] > [Reset All]
2 Select [OK] and then press SET twice.
C
31
[Move]
English
2 Push the joystick up/down to select the setting you want to move and
then press SET.
• An orange ] icon will appear next to the setting you selected to
move.
[Edit]
[Delete]
[¥ My Menu]
[Edit]
[Reset All]
Preparing the Camcorder
Preparing the Camcorder
This section outlines the basic preparations for the camcorder, such as attaching the microphone holder and
lens hood and adjusting the OLED screen, viewfinder and grip.
32
Attaching the Microphone Holder Unit
Use the supplied screws to attach the microphone holder unit to the
handle.
Attaching the Lens Hood
Attach the lens hood to protect the lens and reduce the amount of
stray light that may hit the lens. Additionally, keeping the lens barrier
closed can help avoid fingerprints and dirt on the lens.
Always remove the lens hood and attach the lens cap when
carrying the camcorder or storing it after use.
1 Remove the lens cap.
Y
P
O
햳
햲
• The lens cap and lens hood cannot be used at the same time.
2 Place the lens hood on the front of the lens with the lock
screw side pointing down (햲) and turn it 90 degrees
clockwise (햳).
C
• Be careful not to deform the lens hood.
• Make sure that the lens hood is aligned with the thread.
3 Tighten the lock screw (햴).
햴
Using the Viewfinder
Adjusting the Viewfinder
1 Adjust the viewfinder’s angle as necessary.
2 Turn on the camcorder and adjust the dioptric
adjustment lever until the viewfinder’s image is sharp.
햲
Dioptric
adjustment lever
햳
Preparing the Camcorder
Attaching and Detaching the Eye Cup
Attach the eye cup so that it covers the rubber
portion of the viewfinder unit.
• For left eye use, attach the eye cup so that the
protruding portion faces the opposite side.
33
English
Eye cup
Viewfinder
unit
Detach the eye cup as shown in the illustration.
C
Y
P
O
Using the OLED Panel
Open the OLED panel 90 degrees.
• You can rotate the panel 90 degrees downward or 180
degrees toward the lens.
NOTES
• About the OLED and viewfinder screens: The screens are
produced using extremely high-precision manufacturing
techniques, with more than 99.99% of the pixels operating to
specification. Less than 0.01% of the pixels may occasionally
misfire. On the viewfinder screen only, pixels may also light up
as white dots. This has no effect on the recorded image and
does not constitute a malfunction.
• When you use a commercially available lens adapter and the image on the screen is inverted, you can use the
[w Other Functions] > [Custom Function] > [Scan Reverse Rec] setting to return the image to the correct
orientation.
Preparing the Camcorder
34
• If you are not interested in using the viewfinder while using the OLED screen, you can set [£ OLED/VF
Setup] > [OLED/VF Simul.] to [Off] to conserve the camcorder’s power. Even when [OLED/VF Simul.] is set to
[Off], closing the OLED panel will automatically activate the viewfinder.
• While recording with the OLED panel facing toward the subject, you can set [£ OLED/VF Setup] > [OLED
Mirror Image] to [On] to flip the image horizontally so subjects can see a mirror image of themselves.
Adjusting the Viewfinder/OLED Screen
[£ OLED/VF Setup]
You can adjust the brightness, contrast, color and sharpness of the
viewfinder and OLED screen independently of each other. Additionally,
you can turn on the increased luminence of the OLED panel or adjust the
backlight of the viewfinder. These adjustments will not affect your
recordings.
[OLED Setup]
[Viewfinder Setup]
Operating modes:
1 Open the setup menu for the viewfinder or OLED screen.
[£ OLED/VF Setup] > [OLED Setup] or [Viewfinder Setup]
Y
P
O
2 Select [Brightness], [Contrast], [Color], [Sharpness], [Luminence] or
[Backlight] and then press SET.
[Brightness: ±0]
[Contrast: ±0]
[Color: ±0]
[Sharpness: 2]
[Luminence: Off]*
[Backlight: Normal]**
* [OLED Setup] only
**[Viewfinder Setup] only
3 Adjust the setting and then press SET.
• Repeat steps 2 and 3 to adjust other settings as necessary.
NOTES
• If you set an assignable button to [OLED Setup] or [Viewfinder Setup] (A 129), you can press the button to
open the respective submenu.
• You can also press the DISP. button and hold it pressed for about 3 seconds to turn the OLED [Luminence]
setting on and off.
• The OLED screen will be dimmed if the camcorder is left unused for approx. 3 minutes (except while recording
or during playback). Performing any operation on the camcorder will return the brightness to its previous level.
C
Adjusting the Color Balance of the OLED Screen
As times passes, the color balance of the OLED screen may change
gradually. You can adjust the color balance of the OLED screen to
compensate for this change.
1 Open the [Color Balance] submenu.
[£ OLED/VF Setup] > [OLED Setup] > [Color Balance]
2 Select [R-B Simult. Adjust.] and then press SET.
3 Change the setting to adjust the red and blue levels simultaneously and
then press SET.
4 If necessary, select [R Fine Tuning] or [B Fine Tuning] to further adjust
only the red or blue level.
5 Adjust the setting as necessary and then press SET.
[£ OLED/VF Setup]
[OLED Setup]
[Color Balance]
[R-B Simult. Adjust: ±0]
[R Fine Tuning: ±0]
[B Fine Tuning: ±0]
Preparing the Camcorder
Setting the Screen to Black & White
[£ OLED/VF Setup]
The viewfinder and OLED screen display in color by default but you can
set them to black & white. Even when the screen is black & white,
onscreen text and icons will still be displayed in color.
[OLED/VF B&W]
1 Open the [OLED/VF B&W] submenu.
[£ OLED/VF Setup] > [OLED/VF B&W]
[Off]
English
2 Select [On] and then press SET.
NOTES
• If you set an assignable button to [OLED/VF B&W] (A 129), you can press the button to turn the black &
white display on and off.
Adjusting the Grip Unit
The grip unit can be rotated 120º (at 15º intervals) to give
you a convenient grip angle for high- and low-angle
shooting.
햲
Y
P
O
1 Push the grip’s UNLOCK lever forward (toward the
START/STOP button on the grip). While holding it
pressed down, rotate the grip unit to the desired angle.
2 At about the desired angle, release the UNLOCK lever
and rotate the grip unit further until it clicks in place.
C
35
Adjusting the Grip Belt
Adjust the grip belt so that you can reach the grip zoom rocker
with your index and middle fingers, and the START/STOP button
with your thumb.
IMPORTANT
• Be careful not to drop the camcorder when adjusting the grip belt.
햳
Preparing the Camcorder
Attaching the Shoulder Strap
Pass the ends through the strap mounts and adjust
the length of the strap.
36
IMPORTANT
• Be careful not to drop the camcorder when attaching
or adjusting the shoulder strap.
Removing and Attaching the Terminal Covers
You can remove the plastic terminal covers of all the camcorder's terminals to access them more readily.
Removing the Terminal Covers
1 Open the terminal cover and pull it out.
Y
P
O
2 Grasp the strip connecting the terminal cover to the camcorder
and pull.
• This step is not necessary for the covers for the REMOTE
terminal and USB terminal, which you only need to pull straight
out.
Attaching the Terminal Covers
C
Insert the connecting strip into the opening to attach the terminal cover.
NOTES
• If the connecting strip is difficult to grasp, use a pair of tweezers or similar tool.
Preparing the Camcorder
Using a Tripod
5.5 mm
You can mount the camcorder on any tripod with a 1/4" mounting screw, no longer than
5.5 mm (0.2 in.). Using tripods with longer mounting screws may cause damage to the
camcorder.
To use a tripod with 3/8" mounting screws, first attach the optional TB-1 Tripod Adapter Base to the camcorder
and then attach the tripod to the adapter base.
1 Remove the tripod base from the camcorder.
• Remove the 4 screws and then remove the base.
2 Attach the optional TB-1 Tripod Adapter Base.
• Firmly screw in the 4 screws.
3 Attach the tripod.
• Firmly screw in the tripod screw.
• If a tripod has both a 1/4" screw and a 3/8" mounting screw, firmly screw in both.
C
Y
P
O
English
Using a Tripod with 3/8" Mounting Screws
37
Preparing Recording Media
Preparing Recording Media
38
The camcorder records movies in MXF format (MXF clips) to 1 CompactFlash (CF) cards and movies in MP4
format (MP4 clips) and photos* to . SD, / SDHC and 0 SDXC memory cards. The camcorder is
equipped with two CF card slots.
The recording media that will be used for recording (CF card, SD card, CF card and SD card, two CF cards)
depends on the movie format (A 55) and CF card recording method (A 42) selected. Be sure to insert
recording media to all the card slots necessary. Initialize recording media (A 41) when you use them with this
camcorder for the first time.
* The camcorder can record custom picture files and a camera settings file onto the SD card as well. The SD card serves also to
store user memo files created with Canon XF Utility that you can then read and embed in the metadata of MXF clips (A 111).
Compatible Recording Media
For the latest information about recording media tested for use with this camcorder, visit your local Canon Web
site.
CF cards: UDMA-compatible1 Type I CF cards. Capacity: 512 MB or larger.
1
The Ultra Direct Memory Access (UDMA) specification allows data to be transferred between the CF card and device at high
transfer speeds (measured in MB/s). Depending on the CF card, you may not be able to record even when using a UDMAcompatible CF card.
SD cards: SD / SDHC / SDXC cards. SD Speed Class2: CLASS 4, 6 or 103.
Y
P
O
As of May 2014, the MP4 recording function has been tested using memory cards made by Panasonic, Toshiba
and SanDisk.
2
3
SD Speed Class is a standard that indicates the minimum guaranteed data transfer of SD cards.
To record MP4 clips with a bit rate of 35 Mbps, we recommend using SD cards rated CLASS 6 or 10.
IMPORTANT
• After repeatedly recording, deleting and editing scenes (fragmented memory), it will take longer to write data
on recording media and recording may stop. Save your recordings and initialize the recording media with the
camcorder.
• About high capacity recording media You can use CF cards with a capacity of 128 GB or larger and SDXC
cards with this camcorder but such recording media are initialized using the exFAT file system.
- When using exFAT-formatted recording media with other devices (digital recorders, card readers, etc.), make
sure that the external device is compatible with exFAT. For more information on compatibility, contact the
computer, operating system or memory card manufacturer.
- If you use exFAT-formatted recording media with a computer OS that is not exFAT-compatible, you may be
prompted to format the memory card. In such case, cancel the operation to prevent data loss.
C
NOTES
• Proper operation cannot be guaranteed for all recording media.
Preparing Recording Media
Inserting a CF Card
햲
You can insert a CF card into CF card slot A or slot B. If you
have two CF cards, you can use both slots.
39
1 Slide down the CF card slot cover switch and open
the CF card slot cover.
English
2 Insert the CF card straight, with the label facing away
from the lens, all the way into the slot.
3 Close the CF card slot cover.
• Do not force the cover closed if the CF card is not
correctly inserted.
Y
P
O
햳
C
Checking the Status of the CF Card Slots
You can check the status of the CF card slots immediately by
looking at the CF2/CF3 access indicator. Refer to the
following table.
Access indicator color
CF card slot status
Red
Accessing the CF card.
Green
Recording/playback is possible and the CF card
slot is selected for recording/playback.
Indicator off
A CF card is not inserted, the CF card slot is not
currently selected, or the CF card is not being
accessed.
If you set the [w Other Functions] > [Media Access LED] setting to [Off], the access indicators will not
illuminate.
햴
Preparing Recording Media
Removing a CF card
1 Wait until the access indicator of the CF card slot with
the CF card to be removed is off.
40
햴
2 Slide down the CF card slot cover switch and open the
CF card slot cover.
햵
3 Push in the CF card release button to release the CF
card.
4 Pull the CF card all the way out and close the CF card
slot cover.
IMPORTANT
• Observe the following precautions while the CF2 or CF3 access indicator is illuminated in red. Failure to do
so may result in permanent data loss.
- Do not disconnect the power source or turn off the camcorder.
- Do not open the cover of the CF card slot being accessed.
Inserting and Removing an SD Card
Y
P
O
1 Make sure the SD card access indicator is off.
2 Open the SD card slot cover.
3 Insert the SD card, with the label facing up, all the way into
the SD card slot until it clicks.
C
• To remove the SD card, push the SD card once to release it.
When the SD card springs out, pull it all the way out.
4 Close the SD card slot cover.
• Do not force the cover closed if the SD card is not correctly
inserted.
SD card access indicator
햳
햵
SD card status
On or flashing
Accessing the SD card.
Off
An SD card is not inserted or the
SD card is not being accessed.
SD card access
indicator
햴
If you set the [w Other Functions] > [Media Access LED] setting to [Off], the access indicator will not illuminate.
IMPORTANT
• Observe the following precautions while the SD card access indicator is on or flashing. Failure to do so may
result in permanent data loss.
- Do not disconnect the power source or turn off the camcorder.
- Do not remove the SD card.
• SD cards have front and back sides that are not interchangeable. Inserting an SD card facing the wrong
direction can cause a malfunction of the camcorder. Be sure to insert the SD card as described in the
procedure above.
Preparing Recording Media
Initializing the Recording Media
The first time you use any recording media with this camcorder, initialize it first. You can also initialize a recording
media to permanently delete all the data it contains.
When initializing an SD card, you can select quick initialization, which clears the file allocation table but does not
physically erase the stored data, or complete initialization, which deletes all data completely.
41
English
Operating modes:
1 Open the [Initialize Media] submenu.
[w Other Functions]
[w Other Functions] > [Initialize Media]
2 Select [CF A], [CF B] or [SD Card] and then press SET.
[Initialize Media]
To initialize a CF card
3 Select [OK] and then press SET.
4 When the confirmation message appears, press SET.
• The CF card is initialized and all the data it contains is erased.
To initialize an SD card
Y
P
O
3 Select [Complete] (complete initialization) or [Quick] (quick initialization) and then press SET.
4 Select [OK] and then press SET.
• If you are using the [Complete] initialization option, press SET twice to cancel the operation while it is in
progress. You can use the SD card but all data will be erased.
5 When the confirmation message appears, press SET.
• The SD card is initialized and all the data it contains is erased.
C
IMPORTANT
• Initializing a recording media will permanently erase all data, including MXF clips with an $ mark and custom
picture files. Lost data cannot be recovered. Make sure you save important recordings in advance.
• Depending on the SD card, the complete initialization may take up to a few minutes.
NOTES
• While recording on a CF card, you can initialize another CF card in the other CF card slot.
• If you set an assignable button to [Initialize Media] (A 129), you can press the button to open the initialization
submenu.
Switching Between the CF Card Slots
The camcorder features two CF card slots, CF2 (CF card slot A)
and CF3 (CF card slot B). If both slots contain a CF card, you can
switch between them as necessary.
Operating modes:
Press the SLOT SELECT button.
• The access indicator of the selected CF card slot will illuminate in
green. On the screen, the CF card selected is indicated with a Ð
mark next to CF card icon.
Preparing Recording Media
42
NOTES
• If both CF card slots contain a CF card and you open the cover of the selected
slot, the camcorder will automatically switch to the other slot.
• You cannot use the SLOT SELECT button to switch between CF card slots
while recording MXF clips.
• While using the Browser Remote application, you can also switch between CF
card slots remotely by pressing [SLOT SELECT] on the Browser Remote
screen.
Selecting the CF Card Recording Method
The camcorder features two useful CF card recording methods, relay recording and double slot recording.
Relay recording: This function allows you to continue recording MXF clips on another CF card without
interruption if the CF card you are using becomes full. Relay recording is available from CF card slot A to CF card
slot B, and vice versa.
Double slot recording: This function records the same MXF clip simultaneously to both CF cards, which is a
convenient way to make a backup copy of your recordings while you record.
Operating modes:
To use relay recording
Y
P
O
By default, this function is activated. If it has been deactivated, follow the
procedure below to activate it.
C
1 Open the [Relay Recording] submenu.
[w Other Functions] > [MXF] > [Relay Recording]
2 Select [On] and then press SET.
[w Other Functions]
[MXF]
[Relay Recording]
[On]
To use double slot recording
1 Open the [Double Slot Recording] submenu.
[w Other Functions] > [MXF] > [Double Slot Recording]
2 Select [On] and then press SET.
•
•
•
•
[w Other Functions]
[MXF]
[Double Slot Recording]
NOTES
You can combine double slot recording and the MXF+MP4 movie
[Off]
format (A 123) to record the same video on three recording media and
in two different movie formats.
When the bit rate is set to 50 Mbps (A 55), relay recording is not available during slow motion recording.
If a CF card becomes full during double slot recording, recording on both CF cards will stop. On the other
hand, if an error occurs with one of the CF cards, recording will continue on the other CF card.
Double slot recording cannot be used with relay recording or slow & fast motion recording.
Preparing Recording Media
Checking the Available Recording Time on a Recording Media
In
mode, the upper left of the screen will show the icon of the recording media that is in use and next to it
the approximate remaining recording time in minutes*. When the movie format (A 55) is set to MXF or
MXF+MP4, the CF card currently selected will be indicated by a Ð mark next to the CF card icon.
On the [Media] status screen (A 211), you can check the total space and used space of each recording media,
as well as the available recording time* and the available number of photos (SD card only).
Recovering Data on a Recording Media
Some actions, such as suddenly turning off the camcorder or removing the recording media while data is being
recorded, can cause data errors on the recording media. In such case, you may be able to recover the data if a
message indicating you that data (CF card) or a clip (SD card) needs recovering. The message appears when
you insert a corrupted CF card into the camcorder or when you try to play back a corrupted MP4 clip from the
[MP4] index screen.
Operating modes:
Y
P
O
1 When the camcorder prompts you to recover the data, select [OK] and then press SET.
2 When the confirmation message appears, press SET.
NOTES
• This procedure will delete clips shorter than 10 seconds in length. Additionally, up to 10 seconds will be
deleted from the end of the clips.
• In some cases, it may not be possible to recover the data. This is more likely when the file system is corrupted
or the recording media is physically damaged.
• While recording on a CF card, you can recover data from another CF card by inserting it into the other CF card
slot.
C
English
* The approximate available recording time is based on the current bit rate (A 55).
43
Remote Operation of the Camcorder
Remote Operation of the Camcorder
44
The camcorder can be operated remotely in a number of different ways with varying degrees of control. First, you
can use the supplied wireless controller as described below. You can also connect an optional RC-V100 Remote
Controller for maximum control of your recordings at a professional level.
Finally, using the camcorder's network functions, you can connect any device with a Web browser either
wirelessly (via Wi-Fi) or through a LAN cable and use the Browser Remote application to control the camcorder
(A 182).
Operating modes:
Using the Supplied Wireless Controller
Inserting the Battery
Insert the supplied CR2025 lithium button battery into the wireless
controller before use.
Y
P
O
햴
1 Press the tab in the direction of the arrow (햲) and pull out the battery
holder (햳).
햵
2 Place the lithium button battery with the + side facing up (햴).
3 Insert the battery holder (햵).
Activating the Wireless Controller
C
By default, the wireless controller is activated. If it has been deactivated,
follow the procedure below to activate it.
1 Open the [Wireless Controller] submenu.
[w Other Functions] > [Wireless Controller]
2 Select [On] and then press SET.
햳
햲
[w Other Functions]
[Wireless Controller]
[On]
NOTES
• If you set an assignable button to [Wireless Controller] (A 129), you can press the button to activate/
deactivate the use of the supplied wireless controller.
Using the Wireless Controller to Operate
the Camcorder
When using the wireless controller, point it at the
camcorder’s remote sensor. When the wireless
controller’s buttons are operated, the camcorder’s
tally lamps will illuminate.
NOTES
• When you use the START/STOP button or ZOOM
buttons on the supplied wireless controller, you
must press the record enable button
simultaneously with the desired button.
• When the camcorder cannot be operated with the supplied wireless controller, or when it can only be operated
at very close range, replace the battery.
• The supplied wireless controller may not work properly when the remote sensor is located under strong light
sources or direct sunlight.
Remote Operation of the Camcorder
Using the Optional RC-V100 Remote Controller
Connection cable
(supplied with the RC-V100)
Y
P
O
1 Turn off the camcorder and connect the optional RC-V100 Remote
Controller to the camcorder.
• For details, refer to the instruction manual of the RC-V100.
2 Turn on the camcorder in
mode and open the [REMOTE Term.]
submenu.
[w Other Functions] > [REMOTE Term.]
C
3 Select [RC-V100] and then press SET.
Options
[RC-V100]:
[Standard]:
[w Other Functions]
[REMOTE Term.]
[Standard]
Select this option to use the optional RC-V100 Remote Controller.
Select this option to use commercially available remote controls.
NOTES
• The camcorder’s ND filter cannot be changed using the ND button on the remote controller.
• When the camcorder is set to full auto mode (A 49), settings related to the aperture, gain, shutter speed and
white balance (except for [R Gain] and [B Gain] in the custom picture's [White Balance] settings) cannot be
changed using the remote controller.
• Custom picture settings can be changed using the remote controller only when an appropriate custom picture
file is selected (A 132).
45
English
You can attach the optional RC-V100 Remote Controller to control the camcorder (including advanced recording
functions) from a distance. In addition to turning the camcorder on and off and navigating the menus, while
recording you can control various camera functions, such as aperture, shutter and zoom, and custom picture
settings, like knee and sharpness.
The connection cable supplied with the RC-V100 is required to connect the RC-V100 to the camcorder's
REMOTE terminal.
Remote Operation of the Camcorder
46
C
Y
P
O
3
Recording
47
Recording Video
Operating modes:
Preparing to Record
1 Remove the lens cap and attach the lens hood
(A 32).
Y
P
O
햲
햶
2 Attach a charged battery pack to the camcorder
(A 24).
햳
3 Insert recording media (one or two CF cards, SD
card) as necessary (A 39, 40).
• Insert a CF card to record MXF clips; insert an SD card
to record MP4 clips.
• Insert CF cards into both CF card slots to use relay
recording (A 42) or double slot recording (A 42).
C
햴
햴
햵
4 Slide down the lens barrier switch to OPEN to open
the lens barrier.
5 Adjust the viewfinder.
NOTES
• The camcorder can add a user memo (A 111) to an MXF clip as you record. It can be used to store
information such as the clip name, camera operator and filming location. However, you must set the user
memo before recording.
English
This section explains the recording basics. Before you begin recording, make a test recording first to check if the
camcorder operates correctly. Record an MXF clip for approximately 6 minutes at 50 Mbps and an MP4 clip for
approximately 20 minutes at 35 Mbps (A 55). Should the camcorder fail to operate correctly, refer to
Troubleshooting (A 218).
For details on recording audio, refer to Recording Audio (A 98).
Recording Video
Recording
1 Hold down the button on the Q switch and slide the switch to CAMERA.
48
• The camcorder turns on in
mode and enters record pause mode.
• The access indicators of card slots with recording media will illuminate momentarily in red. Then, the CF
card access indicator of the CF card slot selected for recording MXF clips will change to green.
Tally lamps
햳, 햴
햲
Tally lamp
햳, 햴
Y
P
O
Access indicators
SD card access indicator
CF card access indicators
2 Press the START/STOP button to begin recording.
• Recording starts. The front and rear tally lamps illuminate and, depending on the movie format selected,
[ÜREC], [ÜMP4] or both displays will appear at the top of the screen.
• You can use the START/STOP button on the grip, on the handle or at the front of the camcorder (next to the
lens).
• When you use the supplied wireless controller, press the START/STOP button and the record enable button
simultaneously.
• For details about recording when the movie format is set to MXF+MP4, refer to Simultaneous Recording of
MXF and MP4 Clips (A 123).
C
3 Press the START/STOP button to pause the recording.
• The clip* is recorded on the recording media and the camcorder enters record pause mode. The tally lamps
will also go out.
* “Clip” refers to a single movie unit recorded with a single recording operation.
IMPORTANT
• Observe the following precautions while any access indicators are illuminated or flashing in red. Failure to do
so may result in permanent data loss.
- Do not open the CF card slot cover or the SD card slot cover of the recording media being accessed and do
not remove the recording media.
- Do not disconnect the power source or turn off the camcorder.
• Be sure to save your recordings regularly (A 168), especially after making important recordings. Canon shall
not be liable for any loss or corruption of data.
NOTES
• The START/STOP button on the handle has a lock lever to prevent accidental operation. Set the lock lever to
C if you do not want a recording inadvertently paused or if you do not plan to use that START/STOP button.
Return the lever to its previous position to enable use of the START/STOP button again.
Recording Video
Recording in Full Auto Mode
Move the FULL AUTO switch to ON to change the camcorder to
full auto mode. In full auto mode, the camcorder automatically
sets the aperture, gain, shutter speed, and white balance. The
camcorder will continuously adjust the brightness and white
balance automatically*. In full auto mode, however, the focus
mode will not be set to autofocus.
* The light metering mode (A 68) will be set to [Standard], AE shift (A 67)
will be set to [±0] and the AGC limit (A 63) will be set to [Off/27 dB].
About MXF Clips
Y
P
O
When the camcorder records an MXF clip, it also assigns a 6-character clip name consisting of a 2-character
prefix (letters or numerals) and 4 numerals (for example, “AA0001”). The last 4 numbers serve as a running
counter that increases every time a clip is recorded. You can set the initial clip name in advance using the
[w Other Functions] > [MXF] > [Clips] > [Title Prefix] and [Number Setting] settings. You cannot change
the clip name after the clip is recorded.
• MXF clips will be split in the following cases.
- When relay recording (A 42) is activated and the selected CF card becomes full, the recording will
continue as a separate relay clip on the other CF card.
- The video (stream) file in a clip will be split approximately every 2 GB for clips with a long recording time
(approximately every 1 GB during slow motion recording). Even in such case, playback will be
continuous.
• If you record using the custom picture and metadata settings, those settings will be recorded with the MXF
clip. For more details, refer to Custom Picture Settings (A 132) and Using Metadata (A 111).
C
About MP4 Clips
• MP4 clips are assigned consecutive file numbers that consist of 7 digits, like “100-0001”. The first 3 digits
indicate the folder where the file is saved and the last 4 digits are a unique identifier for each file. You can
select how the files are numbered (A 117).
• For scenes with a long recording time, the video (stream) file in a clip will be split in the following cases.
Even in such case, playback will be continuous. Using Data Import Utility (A 170), you can join such split
files and save them on a computer as a single clip.
- When the file size reaches approximately 4 GB.
- After recording a single clip continuously for approximately 29 minutes 50 seconds (frame rate set to
59.94P) or for approximately 59 minutes 50 seconds (other frame rates).
• A single MP4 recording operation can go on continuously for about 12 hours. Then the camcorder will stop
automatically.
49
English
• You can use [w Other Functions] > [Review Recording] (A 116) to review part or all of the last clip recorded.
• If you set an assignable button to [Add $ Mark] or [Add % Mark] (A 129), you can press the button to add
an $ mark or % mark to the last MXF clip recorded.
• You can use [w Other Functions] > [Delete Last Clip] to delete the last clip recorded. However, you cannot
delete the last clip if double slot recording is activated or if the movie format is set to MXF+MP4.
• When you set [¢ Video Setup] > [Rec Command] to [On] and you connect the camcorder to another
device using the 3G/HD-SDI terminal (
only) or HDMI OUT terminal, if you start or stop recording with
the camcorder, the other device will also start or stop recording.
Recording Video
Remote Operation Using Browser Remote
After completing the necessary preparations (A 182), you can start and stop recording from a connected
device using the Browser Remote application.
50
1 Press [LIVE VIEW ON/OFF] to show the camcorder’s live view image on the Browser Remote screen.
2 Press [START/STOP] to begin recording.
• Depending on the movie format selected, the recording operation indicator changes to [ÜREC] (MXF clips),
[ÜMP4] (MP4 clips) or both and the center of the START/STOP button lights up in red.
• The time code displayed on the Browser Remote screen is the same as on the camcorder.
• Press [START/STOP] again to pause the recording.
Recording operation
Time code
Y
P
O
NOTES
• The Browser Remote application has a key lock function that is limited only to the controls on the application’s
screens (you will still be able to use the controls on the camcorder). Press [D] to lock the application’s
controls; press [C] to reactivate them.
C
Recording Video
Onscreen Displays
Refer to this section for an explanation of the various screen displays that appear in
mode. You can use
the custom display function (A 142) to turn off individual onscreen displays if they are not required. The menu
item that controls each display is given in the following table (1: indicates a menu item under [Custom Display 1]
and 2: indicates a menu item under [Custom Display 2]).
32
33
C
44
Y
P
O
34 36 38 40
42 43
35 37 39
41
When displaying the date and time (A 28):
Icon/Display
16 17 18 19
20
21
22
23
24
25
26
27
28
29
30
31
Number
15
English
13 14
1
2
3
4
5
6
7
8
9
10
11
12
Description
Custom Display
A
1
è é ê Remaining battery charge
ë ì (in red)
The icon shows an estimate of the remaining charge. When using a
000 min
battery pack compatible with Intelligent System, the remaining
recording time is displayed, in minutes, next to the icon.
• When ì is displayed, replace the battery pack with a fully
charged one.
• Depending on the conditions of use, the actual battery charge may
not be indicated accurately.
2:
[Remaining Battery]
–
2
Recording media status and available recording time estimate
2:
[Remaining Rec Time]
–
200 min, 300 min
MXF recording: in green - can record; in white - reading the CF card.
The CF card selected for recording is indicated with a Ð mark.
4, 5 (in red)
No CF card or cannot record on the CF card.
00 min
MP4 recording: in green - can record; in yellow - the SD card is almost
full.
(in red)
No SD card or cannot record on the SD card.
400 min
3
Remaining recording time for double slot recording (A 42): in green can record; in red - cannot record.
• Displayed only when the movie format is set to MXF.
Zoom indicator
00/00
51
1: [Zoom Position]
74,
141
Recording Video
Number
4
52
Icon/Display
±000
Description
Focal length guide
Custom Display
A
–
128
1: [Infrared]
126
5
Infrared <,=
Infrared mode and status of the infrared light
6
b (in yellow/red), `
Temperature warning/Fan operation.
2: [Temperature/Fan]
• When the camcorder’s internal temperature is high, b will appear in
yellow. If the temperature rises further due to continued use, it will
change to red and the fan may be activated atutomatically.
54
7
A 0.0ft
@?=
Focus mode
• While focusing in manual focus mode, the estimated distance to the
subject will be displayed as well.
81
,
1: [Focus Mode],
1: [Object Distance]
Face AF
85
8
ND 1/2, 1/4, 1/8
ND filter
1: [ND Filter]
9
°, ®
Light metering mode
1: [Light Metering]
68
10
/0, .0
Custom picture
1: [Custom Picture]
132
11
@
Full auto mode
1: [Full Auto]
49
12
0000 K
ÅA/ÅB 0000 K
È0000 K, ¼, É
White balance
1: [White Balance]
69
13
Network functions
,
,
0
14
1
15
Recording operation
Y
P
O
Network type (Wi-Fi, Camera Access Point, Ethernet) and connection
status: in white - function ready to be used; in yellow - connecting to or
disconnecting from a network.
2:
[Network Functions]
67
174,
177,
179
FTP file transfer and number of files queued: icon in white - login to the
FTP server completed; in yellow - logging in to the FTP server; in red FTP transfer not possible.
189
Browser Remote: in white - preparations for connection completed; in
yellow - connecting to or disconnecting from the control device; in red Browser Remote cannot be used.
182
C
Wireless controller disabled
2:
[Wireless Controller]
44
2: [Recording Mode]
–
STBY, ÜREC
MXF recording: record pause, recording.
MP4, ÜMP4
MP4 recording: record pause, recording.
INT STBY, ÜINT STBY,
ÜINT REC
Interval recording: record pause (before the sequence has started),
recording standby (once the sequence has started), recording.
• In record pause mode before the interval recording sequence has
started, [INT] flashes.
118
FRM STBY, ÜFRM STBY,
ÜFRM REC
Frame recording: record pause (before the sequence has started),
recording standby (once the sequence has started), recording.
• In record pause mode before the frame recording sequence has
started, [FRM] flashes.
119
S&F STBY, ÜS&F REC
Slow & fast motion recording: record pause, recording.
120
PRE REC STBY,
ÜPRE REC
Pre-recording: record pause, recording.
121
,¸
16
Movie format
2: [Movie Format]
55
17
4
Double slot recording
2: [Recording Mode]
42
18
U
Genlock (
2: [Genlock]
94
19
S
Onscreen displays superimposed on the recording
2: [OSD Recording]
141
20
00:00:00.00, 00:00:00:00
Time code
2: [Time Code]
90
Approximate number of photos that can be recorded on the SD card
2: [Remaining Photos]
195
21
0000
only)
Recording Video
Number
Icon/Display
Description
Custom Display
A
1s - 10m00s
Interval recording counter
2: [Interval Counter]
118
23
00 Mbps
0000x0000
Bit rate (Mbps) and resolution
2: [Bit Rate/
Resolution]
55
24
00.00P, 00.00i
Frame rate
• During slow & fast motion recording, the shooting frame rate is also
displayed (00/00.00P).
2: [Frame Rate]
56
25
REC`, STBY`
Output recording command
2: [Rec Command]
49
GPS signal: continuously on - satellite signal acquired; flashing satellite signal not acquired.
• Displayed only when an optional GP-E2 GPS Receiver is connected
to the camcorder.
2: [GPS]
114
111
26
27
Q
User memo
2: [User Memo]
28
00 00 00 00
User bit
2: [User Bit]
93
4-channel audio recording
2: [4-Channel Input]
100
Audio output channels
2: [Monitor Channels]
166
Aperture value
1: [Iris]
65
Conversion lens
1: [Conversion Lens]
80
1: [Gain]
62
Exposure bar
• Only displayed when the gain, iris and shutter are all set to manual
adjustment.
1: [Exposure]
67
Shutter speed
1: [Shutter]
58
1: [Exposure]
67
1: [Peaking]
84
1: [Tele-converter]
74
1: [Magnification]
84
1: [OIS Functions]
87
29
30
31
CH0/CH0
/
F0.0
32
À, Á
33
L/M/H
/
00.0dB
34
35
/
/
/
1/0000,
000.00Hz,
000.00°
Gain
C
36
AE ±0.00
AE Shift
37
J, K
Peaking
38
b, c, d
Digital tele-converter
39
^
Magnification
40
OIS functions
Å, Ä
Image stabilizer
Y
P
O
È
Powered IS
41
T
Output onscreen displays
2: [Output Display]
165
42
æ
Audio peak limiter
2: [Audio Level]
106
43
44
Audio level meter
Date/time
NOTES
• You can press the DISP. button to switch the onscreen displays in the following sequence.
Show all onscreen displays show only onscreen markers* hide all onscreen displays.
* Only when [£ OLED/VF Setup] > [Markers] > [Enable] is set to [On].
105
–
28
53
English
22
Recording Video
Power Save Mode
54
Activate the power save mode to turn off the screen and reduce
battery consumption. At the press of a button, the camcorder will
immediately return to record pause mode.
1 Hold the POWER SAVE button pressed down for at least
1 second.
• The screen will turn off and the power indicator will illuminate
in orange.
• During power save mode, the tally lamps will flash twice
approximately every 3 seconds. The camcorder retains
previous time code and camcorder settings.
2 Press the POWER SAVE button to return the camcorder to record pause mode.
Using the Fan
During
mode, the camcorder uses an internal cooling fan to reduce the camcorder’s internal heat.
Operating modes:
1 Open the [Fan] submenu.
[w Other Functions] > [Fan]
Y
P
O
2 Select the desired option and then press SET.
Options
[On]:
C
[w Other Functions]
[Fan]
[On]
The fan runs at a slow speed at all times (except when the camcorder is in power save mode, then it is
turned off). Use this default setting in most cases.
[Automatic]: The fan runs at a high speed while the camcorder is not recording (including during power save mode)
and it is automatically turned off while the camcorder is recording. However, if the internal temperature of
the camcorder is too high (b appears in red), the fan will be activated automatically (in that case, `
will appear next to the b icon). When the camcorder’s temperature has decreased sufficiently, the fan
will be turned off. Use this setting when you do not want the camcorder to pick up the operating sound
of the cooling fan.
NOTES
• Be careful not to cover with tape or otherwise obstruct the cooling fan’s air intake and exhaust vents (marked
as AIR INTAKE/EXHAUST VENT).
Exhaust vents
Intake vents
Video Configuration: Movie Format, Bit Rate, Resolution and Frame Rate
Video Configuration: Movie Format, Bit Rate, Resolution and
Frame Rate
Before you record, select the movie format, bit rate, resolution (frame size) and frame rate that best match your
creative needs.
English
Operating modes:
55
Selecting the Movie Format
[w Other Functions]
You can record video in MXF format, MP4 format or simultaneously in
both formats. MXF clips are recorded on a CF card while MP4 clips are
recorded on an SD card, so be sure to insert the appropriate recording
media according the movie format you want to use. If you can combine
the MXF+MP4 movie format with double slot recording (A 42), you can
record the same video on three recording media and in two different
formats.
1 Open the [Movie Format] submenu.
[w Other Functions] > [Movie Format]
] to record only MP4 clips, or [MXF (CF)+MP4
1 Depending on the movie format selected, open the corresponding [Bit
Rate/Resolution] submenu to set the bit rate and resolution.
[w Other Functions] > [MXF] > [Bit Rate/Resolution] (MXF clips)
[w Other Functions] > [MP4] > [Bit Rate/Resolution] (MP4 clips)
C
[MXF (CF)]
Y
P
O
2 Select [MXF (CF)] to record only MXF clips, [MP4
record simultaneously in both formats.
Selecting the Bit Rate and Resolution
[Movie Format]
2 Select the desired option and then press SET.
• The selected bit rate and resolution will appear on the upper right of
the screen. However, when the movie format is set to MXF+MP4,only
the bit rate and resolution of the MXF clips will appear on the screen.
] to
[w Other Functions]
[MXF]
[Bit Rate/Resolution]
[50 Mbps 1920x1080]
[w Other Functions]
[MP4]
[Bit Rate/Resolution]
[24 Mbps 1920x1080]* or
[Linked to MXF]**
* When the movie format is set to
MP4.
** When the movie format is set to
MXF+MP4.
Video Configuration: Movie Format, Bit Rate, Resolution and Frame Rate
Selecting the Frame Rate
56
[w Other Functions]
When [Bit Rate/Resolution] is set to [35 Mbps 1440x1080] (MXF clips) or
[35 Mbps 1920x1080] or [17 Mbps 1280x720] (MP4 clips), the frame rate
is set automatically and cannot be changed.
[MXF]
1 Depending on the movie format selected, open the corresponding
[Frame Rate] submenu to set the frame rate.
[w Other Functions] > [MXF] > [Frame Rate] (MXF clips)
[w Other Functions] > [MP4] > [Frame Rate] (MP4 clips)
[Frame Rate]
[59.94i]
2 Select the desired option and then press SET.
• The selected frame rate will appear on the upper right of the screen.
When the movie format is set to MXF+MP4, only the bit rate/
resolution of MXF clips will appear on the screen.
[w Other Functions]
[MP4]
NOTES
• For details about the video configuration of MP4 clips recorded when
the movie format is set to MXF+MP4, refer to Simultaneous Recording
of MXF and MP4 Clips (A 123).
• For details on the signal output from each terminal, refer to Video
Output Configuration (A 159).
[Frame Rate]
[29.97P]
Y
P
O
MXF clips: Available bit rate, resolution and frame rate settings
[Bit Rate/Resolution]
[Frame Rate]
Bit rate*
Resolution
59.94i
50 Mbps
(CBR 4:2:2)
1920 x 1080
Ü
1280 x 720
1920 x 1080
35 Mbps
(VBR 4:2:0)
1440 x 1080
1280 x 720
25 Mbps
(CBR 4:2:0)
1440 x 1080
C
–
Ü
Ü
59.94P
29.97P
23.98P
–
Ü
Ü
Ü
Ü
Ü
–
Ü
Ü
–
–
–
–
Ü
Ü
Ü
Ü
–
Ü
Ü
* The first line indicates the bit rate (in Mbps); the second line indicates in parentheses whether the bit rate is constant (CBR) or
variable (VBR), and the color sampling.
MP4 clips: Available bit rate, resolution and frame rate settings
[Bit Rate/Resolution]
Bit rate
35 Mbps
24 Mbps
17 Mbps
9 Mbps
3 Mbps**
Resolution
1920 x 1080
1280 x 720
Audio bit rate
256 kbps
128 kbps
640x360
** Only when the movie format is set to MXF+MP4 (A 123).
[Frame Rate]
59.94P
29.97P
Ü
–
23.98P
–
–
Ü
Ü
Ü
–
–
–
Ü
Ü
–
Ü
Ü
Changing Main Camera Functions with the Joystick
Changing Main Camera Functions with the Joystick
You can adjust three main camera functions –shutter speed, white balance and gain– using only the joystick
(direct setting mode). This section will explain the basic operation of the direct setting mode. For specific details
about the functions please refer to the each function’s section: shutter speed (A 58), white balance (A 69),
gain (A 62).
57
English
Operating modes:
Using the Direct Setting Mode
1 Press SET.
• The onscreen display of the function to be
adjusted will be highlighted in orange.
• Push the joystick left/right to change the function
to be adjusted. Pushing the joystick to the right
will cycle through the options in the following
order: White balance White balance preset
fine tuning/color temperature setting1 Gain
mode Gain value2 Shutter speed mode3 Shutter value2, 3 White balance
1
Y
P
O
Only when the white balance mode is set to preset white
balance or color temperature.
2 Only during manual adjustment mode.
3 Only when the SHUTTER switch is set to ON.
C
2 Push the joystick up/down to change the selected mode or select the desired value and then press
SET.
• The selected mode/value will be set and the camcorder will exit the direct setting mode.
• Depending on the function selected, additional adjustment may be possible or necessary before pressing
SET.
NOTES
• The direct setting mode will end automatically if no operation is performed for about 6 seconds or if you open
the menu or a status screen.
Shutter Speed
Shutter Speed
Set the shutter speed based on the recording conditions. For example, you may want to set slower shutter
speeds in darker environments. The camcorder offers the following 6 modes.
58
Operating modes:
OFF: The camcorder uses a standard shutter speed based on
the frame rate. To turn off the shutter adjustment and use the
standard shutter speed, set the SHUTTER switch to OFF.
[Automatic]: The camcorder automatically adjusts the shutter
speed based on the picture’s brightness. This mode is not
available during slow & fast motion recording mode.
[Speed]: Allows you to set the shutter speed (in fractions of a
second). You can select the shutter speed increment between
normal and fine.
[Angle]: You can set the shutter angle to determine the shutter
speed.
Y
P
O
[Clear Scan]: Set the frequency in order to record CRT computer
monitors without displaying black bands or flicker on the screen.
[Slow]: You can set slower shutter speeds to obtain brighter
recordings in places with insufficient lighting. This mode is not
available during slow & fast motion recording mode.
Available shutter speeds
C
The available shutter speeds vary depending on the frame rate.
Shutter speed mode
OFF
[Automatic]1
[Speed]3
[Angle]4
[Clear Scan]4
[Slow]1
1
2
3
59.94i / 59.94P
1/60
1/60 to 1/500
1/60 to 1/100
During
infrared
mode
During
1/30 to 1/100
infrared
mode with
slow shutter2
1/60, 1/75, 1/90, 1/100, 1/120, 1/150,
1/180, 1/210, 1/250, 1/300, 1/360,
1/420, 1/500, 1/600, 1/720, 1/840,
1/1000, 1/1200, 1/1400, 1/1700,
1/2000
360°, 240°, 216°, 180°, 120°, 90°,
60°, 45°, 30°, 22.5°, 15°, 11.25°
59.94 Hz to 250.51 Hz
1/4, 1/8, 1/15, 1/30
Frame rate
29.97P
23.98P
1/30
1/30 to 1/500
1/30 to 1/100
1/24
1/24 to 1/500
1/24 to 1/100
1/15 to 1/100
1/12 to 1/100
1/30, 1/34, 1/40, 1/48, 1/50, 1/60, 1/75,
1/90, 1/100, 1/120, 1/150, 1/180, 1/210,
1/250, 1/300, 1/360, 1/420, 1/500,
1/600, 1/720, 1/840, 1/1000, 1/1200,
1/1400, 1/1700, 1/2000
360°, 240°, 216°, 180°, 120°,
108°, 90°, 60°, 45°, 30°, 22.5°,
15°, 11.25°
29.97 Hz to 250.51 Hz
1/4, 1/8, 1/15
1/24, 1/25, 1/30, 1/34, 1/40, 1/48, 1/50,
1/60, 1/75, 1/90, 1/100, 1/120, 1/150,
1/180, 1/210, 1/250, 1/300, 1/360,
1/420, 1/500, 1/600, 1/720,1/840,
1/1000, 1/1200, 1/1400, 1/1700, 1/2000
360°, 345.6°, 288°, 240°, 180°,
172.8°, 144°, 120°, 90°, 86.4°, 72°,
60°, 45°, 30°, 22.5°, 15°, 11.25°
23.98 Hz to 250.51 Hz
1/3, 1/6, 1/12
Not available during slow & fast motion recording mode.
[~ Camera Setup] > [Infrared] > [Slow Shutter] set to [On].
When [~ Camera Setup] > [Shutter] > [Shutter Increment] is set to [Normal]. When [Shutter Increment] is set to [Fine], you
can adjust the shutter speed in increments of up to 1/256 stop.
4 During slow & fast motion recording mode, available values will vary depending on the selected shooting frame rate.
Shutter Speed
Automatic Shutter
Using the Joystick
1 Set the SHUTTER switch to ON.
59
3 Push the joystick up/down to select the
then press SET.
English
2 Press SET and push the joystick left/right until the
shutter speed mode icon is highlighted in orange.
icon and
• The shutter speed will be set automatically.
NOTES
• You can also set [~ Camera Setup] > [Shutter] >
[Mode] to [Automatic]. Additionally, if you set an assignable
button to [Shutter Mode] (A 129), you can press the
button to change the shutter speed mode between manual
and automatic.
Y
P
O
Remote Operation Using Browser Remote
After completing the necessary preparations (A 182), you can change the shutter speed mode remotely from a
connected device using the Browser Remote application.
1 Press the shutter speed mode button on the Browser Remote screen.
2 Select [Auto].
햲
C
햳
Shutter Speed
Manual Shutter
When the shutter speed mode is set to manual, you can select to adjust the shutter as a shutter speed, angle
value, clear scan frequency or slow shutter speed according to your shooting needs.
60
Changing the Shutter Speed Mode and Value
1 Set the SHUTTER switch to ON.
2 Open the shutter [Manual] submenu.
[~ Camera Setup] > [Shutter] > [Manual]
3 Select the desired mode and then press SET.
• If you selected [Speed] (the default value), you can
select the increment scale to use when adjusting the
shutter speed; otherwise, skip to step 6.
4 Open the [Shutter Increment] submenu.
[~ Camera Setup] > [Shutter] > [Shutter Increment]
5 Select [Normal] or [Fine] and then press SET.
• If you select [Fine], you can adjust the shutter speed in
increments of up to 1/256 step.
Y
P
O
6 Close the menu and change the shutter speed
mode to manual using the direct setting mode.
• Press SET and push the joystick left/right until the shutter speed mode
icon is highlighted in orange, select the icon and press SET. For
details refer to Using the Direct Setting Mode (A 57).
C
7 Adjust the shutter speed, angle value or clear scan frequency
using the direct setting mode.
• Press SET and push the joystick left/right until the shutter value is
highlighted in orange, select the desired value and then press SET. For
details refer to Using the Direct Setting Mode (A 57).
• If in step 3 you selected [Clear Scan], adjust the frequency so that
black bands do not appear on the screen.
[~ Camera Setup]
[Shutter]
[Manual]
[Speed]
[~ Camera Setup]
[Shutter]
NOTES
• If you set an assignable button to [Shutter Increment] (A 129), you can
press the button to change the shutter increment (steps 4-5).
Additionally, if you set an assignable button to [Shutter Mode], you can
press the button to change the shutter speed mode between manual
and automatic (step 6).
[Shutter Increment]
[Normal]
Remote Operation Using Browser Remote
After completing the necessary preparations (A 182), you can adjust the shutter speed remotely from a
connected device using the Browser Remote application.
1 Press the shutter speed mode button on the Browser Remote screen.
2 Select the desired mode.
3 Press the current shutter speed, angle value or clear scan frequency and select the desired value
from the list.
• You may need to scroll up/down to see all the available values.
• The selected value will be displayed on the Browser Remote screen and will be applied on the camcorder.
Shutter Speed
햳
햲
햴
61
English
Using Slow Shutter Mode
When recording in dark surroundings, you can obtain a brighter picture by using slow shutter mode. You can
also use this mode when you wish to add certain effects to your recordings, such as blurring the background
during panning shots or recording a moving subject with an afterimage trail.
• Image quality may not be as good as when using faster shutter speeds in brighter surroundings.
• Autofocus may not work well.
•
•
•
•
NOTES
Closing down the aperture when recording under bright conditions may cause the picture to appear soft or out
of focus. To avoid the loss of sharpness due to diffraction, use a faster shutter speed or open up the aperture
(A 65).
When the gain and aperture are set to manual and the shutter speed mode is not set to [Automatic], the
exposure bar will appear on the screen (A 67).
When you set the camcorder to infrared mode (A 126), the shutter speed mode will be set to automatic. If
you set the camcorder to slow & fast motion recording and infrared mode at the same time, the shutter speed
mode will be set to OFF.
When an optional RC-V100 Remote Controller is connected to the camcorder, you can change the shutter
speed mode with the remote controller’s SHUTTER SELECT button, regardless of the position of the
camcorder's SHUTTER switch.
C
Y
P
O
Flicker Reduction
You can perform the following procedure to have the camcorder
automatically detect and reduce flicker.
1 Open the [Flicker Reduction] submenu.
[~ Camera Setup] > [Flicker Reduction]
[~ Camera Setup]
[Flicker Reduction]
[Off]
2 Select [Automatic] and then press SET.
NOTES
• When recording under artificial light sources such as fluorescent, mercury or halogen lamps, the screen may
flicker depending on the shutter speed. You may be able to avoid flicker by setting the shutter speed mode to
[Speed] and the shutter speed to a value matching the frequency of the local electrical system: 1/50* or 1/100
for 50 Hz systems, 1/60 or 1/120 for 60 Hz systems.
* May not be available depending on the frame rate.
Gain
Gain
62
Depending on the shooting conditions you may want to adjust the brightness of the image. You can do so by
changing the gain value to adjust the sensitivity of the sensor. The camcorder offers 3 independently adjustable
gain levels (L/M/H), for each of which you can select automatic gain (including the option to limit the maximum
gain value) or manual gain control.
Operating modes:
Available gain settings
Increment
Gain
3 dB
-6 dB*, -3 dB*, 0 dB, 3 dB, 6 dB, 9 dB, 12 dB, 15 dB, 18 dB, 21 dB, 24 dB, 27 dB, 33 dB*
0.5 dB (when [Fine Tuning] is selected)
-6 dB to -0.5 dB*, 0 dB to 27 dB
* These values cannot be selected when the [Gamma] setting in the custom picture file (A 135) is set to [Wide DR].
Selecting the Gain Level
Y
P
O
You can set beforehand 3 gain levels (including automatic gain control) and then select quickly which one to
apply simply by changing the position of the GAIN switch.
Set the GAIN switch to the position you want to adjust
(L, M or H).
• L, M or H and the gain value currently assigned to that
position will be displayed on the screen.
Automatic Gain Control (AGC)
Using the Joystick
C
1 Press SET and push the joystick left/right until the
gain mode icon is highlighted in orange.
2 Push the joystick up/down to select the
then press SET.
icon and
• The current position of the GAIN switch will be set to automatic gain control.
NOTES
• You can also set the respective [Mode] setting ([~ Camera Setup] > [Gain] > [L], [M] or [H] > [Mode]) to
[Automatic]. Additionally, if you set an assignable button to [Gain Mode] (A 129), you can press the button to
change the gain mode of the currently selected gain position between manual and automatic.
Remote Operation Using Browser Remote
After completing the necessary preparations (A 182), you can change the gain mode of the currently selected
gain position remotely from a connected device using the Browser Remote application.
1 Press the gain mode button on the Browser Remote screen.
2 Select [Auto].
Gain
햳
햲
63
For each gain position, you can activate the gain limit to prevent the camcorder from setting a level higher than a
preset limit between 0 dB and 27 dB. When you set the camcorder to full auto mode (A 49) or infrared mode
(A 126), [AGC Limit] will be set to [Off/27 dB].
1 Open the [AGC Limit] submenu.
[~ Camera Setup] > [Gain] > [L], [M] or [H] > [AGC Limit]
2 Select the desired level and then press SET.
[~ Camera Setup]
[Gain]
[L], [M] or [H]
Manual Gain
Using the Joystick
C
Y
P
O
[AGC Limit]
[Off/27 dB]
1 Change the gain mode to manual using the direct setting mode.
• Press SET and push the joystick left/right until the gain mode icon is highlighted in orange, select the
and press SET. For details refer to Using the Direct Setting Mode (A 57).
• The current position of the GAIN switch will be set to manual gain.
icon
2 Adjust the gain value using the direct setting mode.
• Press SET and push the joystick left/right until the gain value is highlighted in orange, select the desired
value and then press SET. For details refer to Using the Direct Setting Mode (A 57).
NOTES
• You can also select the gain value from the respective [Manual] setting ([~ Camera Setup] > [Gain] > [L],
[M] or [H] > [Manual]). Using the menu, you can also select [Fine Tuning] and then select a gain level between
-6.0 dB and 24.0 dB in 0.5 dB increments. Once you have selected [Fine Tuning] in the menu, you can then
adjust the gain value in 0.5-dB increments also using the direct setting mode.
Remote Operation Using Browser Remote
After completing the necessary preparations (A 182), you can adjust the gain value of the currently selected
gain position remotely from a connected device using the Browser Remote application.
1 Press the gain mode button on the Browser Remote screen and then select [Manual].
2 Press the current gain value and select the desired value from the list.
• You may need to scroll up/down to see all the available values.
• The selected value will be displayed on the Browser Remote screen and will be applied on the camcorder.
English
Setting the Gain Limit (AGC Limit)
Gain
햳
햲
64
NOTES
• When the gain and aperture are set to manual and the shutter speed mode is not set to [Automatic], the
exposure bar will appear on the screen (A 67).
• When high gain levels are set, the picture may flicker slightly. Additionally, uneven color, noise (white dots) and
vertical stripes and other artifacts are more likely to appear.
• When you set the camcorder to infrared mode (A 126), the gain mode will be set to automatic gain control.
• You can use the [w Other Functions] > [Custom Function] > [Shockless Gain] setting (A 141) for a
smooth transition when changing the position of the GAIN switch.
• When an optional RC-V100 Remote Controller is connected to the camcorder, you can adjust the gain value
corresponding to the current position of the GAIN switch (L, M or H) with the remote controller’s ISO/GAIN
Í/Î buttons.
C
Y
P
O
Aperture
Aperture
You can affect the brightness of your recordings or change the depth of field by adjusting the aperture. For
example, use a small aperture value for a shallow depth of field that isolates the subject in focus and nicely blurs
the background. You can have the camcorder adjust the aperture automatically or you can adjust it manually to
have more control over your recording.
English
Operating modes:
Available aperture values
Aperture Value
Aperture Mode
(IRIS (ND) switch)
Only when [Iris Limit]* is set to [Off]
A (automatic)
F1.8 to F16
M (manual)
F1.8, F2.0, F2.2, F2.4, F2.6, F2.8, F3.2, F3.4, F3.7, F4.0,
F4.4, F4.8, F5.2, F5.6, F6.2, F6.7, F7.3, F8.0
–
F8.7, F9.5, F10, F11, F12, F14, F15, F16, CLOSE
* [w Other Functions] > [Custom Function] > [Iris Limit].
Automatic Aperture
Set the IRIS (ND) switch to A.
•
65
Y
P
O
will appear on the screen next to the aperture
value.
C
NOTES
• You can use the [w Other Functions] > [Custom
Function] > [AE Response] setting (A 141) to
change how quickly the aperture changes during
automatic aperture mode.
Remote Operation Using Browser Remote
After completing the necessary preparations (A 182), you can change the aperture mode remotely from a
connected device using the Browser Remote application.
1 Press the aperture mode button on the Browser Remote screen.
2 Select [Auto].
햲
햳
Aperture
Manual Aperture
Using the Iris Ring
1 Set the IRIS (ND) switch to M.
66
•
will appear on the screen next to the aperture
value.
2 Turn the iris ring to adjust the aperture.
• The aperture value displayed on the screen will
change in 1/4-stop increments.
Remote Operation Using Browser Remote
After completing the necessary preparations (A 182),
you can adjust the aperture value remotely from a
connected device using the Browser Remote
application.
1 Press the aperture mode button on the Browser
Remote screen and then select [Manual].
2 Press the current aperture value on the Browser Remote screen and select the desired aperture
value from the list.
Y
P
O
• You may need to scroll up/down to see all the available values.
• Alternatively, you can press [IRIS (ND) +] to open the aperture or [IRIS (ND) -] to close the aperture in 1/16stop increments. (Onscreen displays will show the closest 1/4-stop aperture value.)
• The selected value will be displayed on the Browser Remote screen and will be applied on the lens.
햲
•
•
•
•
•
•
C
햳
햳
NOTES
When the gain and aperture are set to manual and the shutter speed mode is not set to [Automatic], the
exposure bar will appear on the screen (A 67).
The aperture value set manually will not be retained when you switch to automatic aperture (with the exception
of full auto mode). Instead, the aperture value set automatically by the camcorder will be used when you
switch back to manual aperture control.
If the ND filter is activated, the picture may become dark when you set a high aperture value. In such case, set
[~ Camera Setup] > [ND Filter] to [Off] and readjust the aperture.
You can use the [w Other Functions] > [Custom Function] > [Iris Ring Direction] setting (A 141) to change
the direction of the adjustment when you turn the iris ring.
When an optional RC-V100 Remote Controller is connected to the camcorder, you can adjust the aperture
with the remote controller’s IRIS dial. At default settings, turn the dial right to open up the aperture (smaller F
value) and left to close the aperture (larger F value).
You can use the [w Other Functions] > [Custom Function] > [Iris Limit] setting (A 141) to prevent the
aperture from closing below the diffraction limit of the lens (F8.0). When it is on, the maximum aperture value is
[F8.0]. When it is off, you can fully close the aperture but aperture values that exceed the diffraction limit will
appear in gray. Using aperture values displayed in gray will cause diffraction blur.
Aperture
ND Filter
At default settings, the camcorder’s ND filter is activated automatically depending on the aperture value. The ND
filter is first activated when you close down the aperture to F4.0 ([ND 1/2] will appear on the screen). As you
close down the aperture further, the ND filter will change to [ND 1/4] and then to [ND 1/8] for aperture values
above F4.4.
If you prefer not to use the ND filter, you can turn it off with the following procedure.
[~ Camera Setup]
[~ Camera Setup] > [ND Filter]
2 Select [Off] and then press SET.
[ND Filter]
Remote Operation Using Browser Remote
[Automatic]
After completing the necessary preparations (A 182), you can change
the ND filter mode remotely from a connected device using the Browser
Remote application.
1 Press [ND Off] on the Browser Remote screen to turn off the ND
filter.
2 Press [ND Auto] to return the camcorder to automatic ND filter mode.
Exposure Compensation - AE Shift
Y
P
O
Use AE shift to compensate the exposure that was set using automatic aperture, in order to darken or lighten the
image. You can select from 17 available AE shift levels.
AE shift is not available when the camcorder is set to full auto mode (A 49).
1 Open the [AE Shift] submenu.
[~ Camera Setup] > [AE Shift]
C
2 Select an AE shift level and then press SET.
• The selected AE shift level will be displayed above the exposure bar
and the camcorder will attempt to adjust the exposure accordingly.
[~ Camera Setup]
[AE Shift]
[±0]
Available AE Shift Levels
+2.0
+1.75
+1.5
+1.25
+1.0
+0.75
+0.5
+0.25
-0.25
-0.5
-0.75
-1.0
-1.25
-1.5
-1.75
-2.0
±0
The Exposure Bar
When the gain and aperture are both set to manual mode and the shutter speed
is set to a mode other than auto, the exposure bar will appear, giving you an
indication of the current exposure. The Î on top of the exposure bar indicates
optimal exposure without any shift (AE±0) and the indicator inside the exposure
bar represents the current exposure.
When the difference between current and optimal exposure is larger than ±2 EV,
the indicator will flash at the edge of the exposure bar.
Optimal exposure AE±0
Current exposure
English
1 Open the [ND Filter] submenu.
67
Aperture
Light Metering Mode
68
Select the light metering mode to match the recording conditions. Using the appropriate setting will ensure that
the camcorder obtains the most suitable exposure level when either the aperture, shutter speed or gain is set
automatically by the camcorder.
1 Open the [Light Metering] submenu.
[~ Camera Setup]
[~ Camera Setup] > [Light Metering]
2 Select the desired option and then press SET.
• The icon of the selected mode appears on the left of the screen.
Options
[Backlight] °: Suitable when recording backlit scenes.
[Standard]: Averages the light metered from the entire screen, giving
more weight to the subject in the center.
[Spotlight] ®: Use this option when recording a scene in which only a
certain part of the picture is lit, for example, when the subject
is lit by a spotlight.
[Light Metering]
[Standard]
NOTES
• If you set an assignable button to [Backlight] or [Spotlight] (A 129), you can press the button to change the
light metering mode.
C
Y
P
O
White Balance
White Balance
The camcorder uses an electronic white balance process to
calibrate the picture and ensure accurate colors under different
lighting conditions. There are 4 methods of setting the white
balance.
Preset white balance: Set the white balance to ¼ (daylight) or
É (incandescent lamp). Preset white balance settings can be
further fine-tuned within a range of -9 to 9. This method can
only be used when the WHITE BAL. switch is set to PRESET.
Set color temperature: Allows you to set the color temperature
between 2,000 K and 15,000 K. This method can only be used
when the WHITE BAL. switch is set to PRESET.
Custom white balance: You can use a white object to establish the white balance and set it to one of two custom
white balance positions, ÅA or ÅB. These correspond, respectively, to positions A and B of the WHITE BAL.
switch.
Y
P
O
When recording under fluorescent lights, we recommend using auto white balance or setting the custom white
balance.
Operating modes:
C
NOTES
• The [Color Matrix] and [White Balance] settings in the custom picture file (A 139) take precedence over the
white balance settings.
• You can use the [w Other Functions] > [Custom Function] > [Shockless WB] setting (A 141) to make the
transition look smoother when you change the white balance settings.
• When an optional RC-V100 Remote Controller is connected to the camcorder, you can adjust the white
balance with the remote controller’s AWB button, A button, B button, PRESET button and Å button.
English
Auto white balance (AWB): The camcorder automatically adjusts
the white balance to the optimal level. This method can be
assigned to any of the three positions of the WHITE BAL.
switch.
69
White Balance
Auto White Balance (AWB)
The camcorder constantly adjusts the white balance automatically to achieve an optimal level. The camcorder
will adjust the white balance if the light source changes.
70
Using the Joystick
1 Set the WHITE BAL. switch to the position you want
to use for auto white balance (A, B or PRESET).
2 Press SET and push the joystick left/right until the
white balance icon is highlighted in orange.
3 Push the joystick up/down to select the
and then press SET.
icon
• The white balance will be adjusted automatically. The
current color temperature will be displayed next to the
icon.
Y
P
O
Remote Operation Using Browser Remote
After completing the necessary preparations (A 182), you can change the white balance mode of the currently
selected WHITE BAL. switch position remotely from a connected device using the Browser Remote application.
C
1 Press the white balance mode button on the Browser Remote screen.
2 Select [Auto].
햲
햳
NOTES
• Custom white balance may provide better results in the following cases:
- Changing lighting conditions
- Close-ups
- Subjects in a single color (sky, sea or forest)
- Under mercury lamps and certain types of fluorescent/LED lights
• You can also set the respective setting ([~ Camera Setup] > [White Balance] > [A], [B] or [~ Camera
Setup] > [White Balance] > [PRESET] > [Mode]) to [AWB]. Additionally, if you set an assignable button to
[WB Mode] (A 129), you can press the button to change the white balance mode of the currently selected
position of the WHITE BAL. switch.
White Balance
Preset White Balance/Color Temperature
The camcorder features two preset white balance settings for recording outdoors (daylight) and indoors
(incandescent light). These preset settings can be fine-tuned between -9 and +9. Alternatively, you can specify
the desired color temperature between 2,000 K and 15,000 K in 100 K increments.
1 Open the PRESET's [Mode] submenu to select the
white balance adjustment mode.
[~ Camera Setup] > [White Balance] > [PRESET] >
[Mode]
2 Select [Preset] and then press SET.
3 Back in the [PRESET] submenu, select [Preset] and
then press SET to select the white balance mode
assigned to the PRESET position.
4 Select [Daylight], [Tungsten] or [Kelvin], press SET and
then press MENU to close the menu.
5 Set the WHITE BAL. switch to PRESET.
Y
P
O
• The icon of the selected white balance mode will appear
on the screen.
6 Press SET and push the joystick left/right until the
white balance icon is highlighted in orange.
7 While the selected icon is highlighted in orange, push
the joystick to the right.
C
• If you selected [Daylight] or [Tungsten], the adjustment
value [±0] will appear next to the icon, highlighted in
orange.
• If you selected [Kelvin], the color temperature value
[5500 K] will appear next to the È icon, highlighted in
orange.
[~ Camera Setup]
[White Balance]
[PRESET]
[Mode]
[Preset]
[~ Camera Setup]
[White Balance]
[PRESET]
[Preset]
[Daylight]
8 Push the joystick up/down to fine tune the preset
setting or set the desired color temperature and then
press SET.
• The selected adjustment value/color temperature will be
set and the camcorder will exit the direct setting mode.
Remote Operation Using Browser Remote
After completing the necessary preparations (A 182), you
can adjust the white balance remotely from a connected
device using the Browser Remote application.
1 Press the white balance mode button on the Browser
Remote screen.
2 Select [¼], [É] or [È].
3 Press the adjustment value [Ê ±0] (¼, É) or color temperature [5500K] (È) and then select the
desired value from the list.
• You may need to scroll up/down to see all the available values.
• The selected value will be displayed on the Browser Remote screen and will be applied on the camcorder.
English
Using the Joystick
71
White Balance
햴
햳
72
햲
White balance fine-tuning
햴
Color temperature
Custom White Balance
You can store two custom white balance settings in the camcorder for recording under more difficult lighting
conditions.
Using the Joystick
1 Set the WHITE BAL. switch to A or B.
Y
P
O
2 Press SET and push the joystick left/right until the
white balance icon is highlighted in orange.
3 Push the joystick up/down to select [ÅA] or [ÅB],
depending on the position of the WHITE BAL. switch.
• To apply the stored custom white balance setting as it is,
press SET. The rest of the procedure is not necessary.
• If a custom white balance has not yet been stored, the
white balance icon (ÅA or ÅB) and default value
(5,500 K) will flash slowly. To establish the custom white
balance, continue the procedure.
C
4 Point the camcorder at a white object so that it fills
the whole screen.
• Use the same lighting conditions you plan to use when
recording.
5 Press the Å button.
• The white balance icon (ÅA or ÅB) will flash quickly.
• Make sure the white object fills the screen until the procedure is completed.
• After the white balance icon stops flashing, the procedure is completed. The setting is retained even if you
turn off the camcorder.
Remote Operation Using Browser Remote
After completing the necessary preparations (A 182), you can set the custom white balance remotely from a
connected device using the Browser Remote application.
1 Press the white balance mode button on the Browser Remote screen.
2 Select [ÅA] or [ÅB].
3 Point the camcorder at a white object so that it fills the whole screen.
• Use the same lighting conditions you plan to use when recording.
• Make sure the white object fills the screen until the procedure is completed.
White Balance
4 Press [Å].
• If a custom white balance has not yet been stored, [Å] will flash slowly.
• During the procedure, [Å] will flash quickly. When it stops flashing, the procedure is completed and the
setting will be applied on the camcorder.
English
햲
73
햵
햳
NOTES
• Using the custom white balance setting:
- Set [~ Camera Setup] > [Zoom] > [Mode] to [Normal].
- Readjust the custom white balance if the light source changes.
- Very rarely and depending on the light source, Å may keep flashing (it will change to a slow flashing). The
result will still be better than with the auto white balance.
C
Y
P
O
Zooming
Zooming
74
You can operate the zoom (optical zoom 20x) using the zoom rocker on the side grip or the one on the handle.
You can also use the zoom ring on the lens or the zoom buttons on the supplied wireless controller.
In addition to the optical zoom, you can use the digital zoom* to extend the zoom range to 120x, or digital teleconverter** function to increase the focal length by a factor of approximately 1.5, 3 or 6.
* In the range beyond the optical zoom (20x to 120x), the image is processed digitally affecting image quality.
** The image is processed digitally throughout the zoom range affecting image quality.
Operating modes:
Selecting the Zoom Mode
1 Open the zoom’s [Mode] submenu.
[~ Camera Setup]
[~ Camera Setup] > [Zoom] > [Mode]
2 Select the desired option and then press SET.
Y
P
O
Options
[Tele-converter 6.0x], [Tele-converter 3.0x], [Tele-converter 1.5x]:
The camcorder processes the image digitally to multiply the
focal length by a factor of 6, 3 or 1.5, respectively.
[Digital Zoom]: The camcorder uses the optical zoom up to 20x and
processes the image digitally after that, up to a magnification
ratio of 120x.
[Normal]:
The camcorder uses only the optical zoom up to 20x.
C
[Zoom]
[Mode]
[Normal]
When you operate the zoom, a zoom indicator* will appear on the screen that
shows the approximate zoom position. The white area of the zoom bar indicates
the optical zoom range and the blue area** indicates the digital zoom range.
* You can use the [w Other Functions] > [Custom Function] > [Zoom Indicator] setting (A 141)
to set the zoom indicator to a numerical display.
** Only when [~ Camera Setup] > [Zoom] > [Mode] is set to [Digital Zoom].
•
•
•
•
•
NOTES
You can set [~ Camera Setup] > [Wide-End Angle] to [Wider] to make the focal length at the wide-angle
end of the zoom range even shorter (approximately 26.8 mm, 35mm-equivalent) and enjoy a wider angle of
view. If you set an assignable button to [Wide-End Angle] (A 129), you can press the button to switch
between the [Normal] and [Wider] settings.
You can attach the TL-H58 Tele-converter or WA-H58 Wide Attachment (both optional) to the camcorder
(A 80). You can even use the TL-H58 in combination with the digital zoom and digital tele-converter
functions.
If you set an assignable button to [Tele-converter] (A 129), you can press the button to activate the digital
tele-converter and select the magnification factor. If you set an assignable button to [Digital Zoom] (A 129),
you can press the button to turn the digital zoom on/off.
When an optional RC-V100 Remote Controller is connected to the camcorder, if the zoom mode is set to one
of the [Tele-converter] options, the remote controller’s EXTENDER indicator will light up.
When [~ Camera Setup] > [Conversion Lens] is set to [WA-H58], the digital zoom and digital teleconverter options are not available.
Zooming
Using the Zoom Ring
Zoom in and out on a subject by turning the zoom ring. The zoom speed depends on how fast
you turn the zoom ring.
Using the Zoom Rockers on the Camcorder
Using the Grip Zoom Rocker
Use the settings in the [~ Camera Setup] > [Zoom] submenu to set
the zoom speed. When you select a constant zoom speed, set one of
16 constant speeds (1 is the slowest, 16 the fastest). With a variable
zoom speed, press gently for a slow zoom; press harder for faster
zooms.
Y
P
O
Move the zoom rocker toward T to zoom out (wide-angle) and
toward S to zoom in (telephoto).
C
75
English
NOTES
• You can change the direction of the adjustment and the sensitivity of the response of the
zoom ring using the [w Other Functions] > [Custom Function] > [Zoom Ring Direction] and
[Zoom Ring Control] settings (A 141).
Zooming
Setting the Zoom Speed
Refer to the following table for approximate zoom speeds of the entire
zoom range (end to end).
76
[~ Camera Setup]
[Zoom]
1 Open the zoom [Speed Level] submenu.
[~ Camera Setup] > [Zoom] > [Speed Level]
[Speed Level]
2 Select [Fast], [Normal] or [Slow] and then press SET.
[Normal]
3 Open the grip rocker [Select] submenu.
[~ Camera Setup] > [Zoom] > [Grip Rocker] > [Select]
4 Select [Constant] or [Variable] and then press SET.
[~ Camera Setup]
[Zoom]
[Grip Rocker]
[Select]
To set the speed level for [Constant]
Y
P
O
5 Open the grip rocker [Constant Speed] submenu.
[Variable]
[~ Camera Setup]
[~ Camera Setup] > [Zoom] > [Grip Rocker] > [Constant Speed]
C
6 Select the desired level and then press SET.
[Zoom]
[Grip Rocker]
[Constant Speed 8]
Grip zoom rocker: Approximate zoom speeds (time required to zoom end-to-end)
[Grip Rocker] settings
[Select]
[Constant]
[Variable]
[Speed Level] setting
[Constant Speed]
[Slow]
[Normal]
[Fast]
[1] (slowest)
4 min. 45 sec.
3 min.
1 min.
[16] (fastest)
4.0 sec.
2.5 sec.
1.7 sec.*
–
4.0 sec. to 4 min. 45 sec.
2.5 sec. to 3 min.
1.7 sec.* to 1 min.
* When the zoom speed is too fast (approx. 1.7 seconds end-to-end), the camcorder will have more trouble focusing automatically
while zooming.
NOTES
• When [~ Camera Setup] > [Zoom] > [High-Speed Zoom] is set to [On] and the grip rocker's zoom speed
is set to [Variable], when you operate the zoom in record pause mode, the actual zoom speed will be as if
[~ Camera Setup] > [Zoom] > [Speed Level] were set to [Fast]. While recording, the zoom speed level will
follow the speed level setting set in the menu.
Zooming
Using the Handle Zoom Rocker
Use the ZOOM SPEED switch and the settings in the
[~ Camera Setup] > [Zoom] submenu to set the
zoom speed.
77
English
Move the zoom rocker toward T to zoom out
(wide-angle) and toward S to zoom in
(telephoto).
Setting the Zoom Speed
Refer to the following table for approximate zoom speeds of the entire
zoom range (end to end).
1 Open the zoom [Speed Level] submenu.
[~ Camera Setup]
[Zoom]
Y
P
O
[~ Camera Setup] > [Zoom] > [Speed Level]
[Speed Level]
2 Select [Fast], [Normal] or [Slow] and then press SET.
3 Open the zoom [Handle Rocker] submenu.
[~ Camera Setup] > [Zoom] > [Handle Rocker H] or [Handle
Rocker L].
• You can set the zoom speed independently for each of the positions
of the ZOOM SPEED switch.
C
4 Select the desired level and then press SET.
5 Set the ZOOM SPEED switch to H or L.
• You can set the ZOOM SPEED switch to OFF to deactivate the zoom
rocker on the handle.
[Normal]
[~ Camera Setup]
[Zoom]
[Handle Rocker H 16]
[Handle Rocker L 8]
Handle zoom rocker: Approximate zoom speeds (time required to zoom end-to-end)
[Speed Level] setting
[Handle Rocker H]/[Handle Rocker L]
setting
[Slow]
[Normal]
[Fast]
[1] (slowest)
4 min. 45 sec.
3 min.
1 min.
[16] (fastest)
4.0 sec.
2.5 sec.
1.7 sec.*
* When the zoom speed is too fast (approx. 1.7 seconds end-to-end), the camcorder will have more trouble focusing automatically
while zooming.
Zooming
Remote Operation
Using the Supplied Wireless Controller or an Optional Remote Controller
78
The zoom speeds when using the supplied wireless controller, the optional RC-V100 Remote Controller or a
commercially available remote control connected to the REMOTE terminal are different. When using the supplied
wireless controller, you must press the record enable button and desired zoom button simultaneously to zoom.
Zoom speeds
Accessory
Zoom speed
Wireless controller (supplied)
Constant zoom speed. See the table at the end of the procedure.
RC-V100 Remote Controller (optional)
Variable speed: The greater the angle at which the RC-V100’s ZOOM dial is rotated from the center,
the faster the zoom.
Commercially available remote controls
If the remote control does not support variable zoom: Constant zoom speed.
If the remote control supports variable zoom: Variable zoom according to the remote control's
settings.
Setting the Zoom Speed of the Supplied Wireless Controller
1 Open the zoom [Speed Level] submenu.
[~ Camera Setup]
Y
P
O
[~ Camera Setup] > [Zoom] > [Speed Level]
[Zoom]
2 Select [Fast], [Normal] or [Slow] and then press SET.
3 Open the zoom [Wireless Controller] submenu.
[Speed Level]
[~ Camera Setup] > [Zoom] > [Wireless Controller]
4 Select the desired level and then press SET.
C
[Normal]
Supplied wireless controller: Approximate zoom speeds (time required to
zoom end-to-end)
[~ Camera Setup]
[Zoom Speed Level] setting
[Wireless Controller]
setting
[Slow]
[1] (slowest)
4 min. 45 sec.
[16] (fastest)
4.0 sec.
[Normal]
[Fast]
3 min.
1 min.
2.5 sec.
1.7 sec.*
* When the zoom speed is too fast (approx. 1.7 seconds end-to-end), the camcorder will
have more trouble focusing automatically while zooming.
[Zoom]
[Wireless Controller]
[8]
NOTES
• When an optional RC-V100 Remote Controller is connected to the camcorder, you can zoom with the remote
controller’s ZOOM dial. At default settings, turn the dial right to zoom in (T) and left to zoom out (W).
Zooming
Remote Operation Using Browser Remote
After completing the necessary preparations (A 182), you can operate the zoom remotely from a connected
device using the Browser Remote application.
Press one of the [ZOOM] controls on the Browser Remote screen to zoom as necessary.
Soft Zoom Control
Y
P
O
Using the soft zoom control function you can make the zoom start or end gradually when you operate the zoom
using one of the rockers on the camcorder, a remote controller or the Browser Remote application.
1 Open the [Soft Zoom Control] submenu.
[~ Camera Setup] > [Zoom] > [Soft Zoom Control]
2 Select [Start] (soft control only at the beginning of the zoom),
[Stop] (soft control only at the end of the zoom) or [Both], and
then press SET.
C
[~ Camera Setup]
[Zoom]
[Soft Zoom Control]
[Off]
English
• Press one of the controls on the [WIDE] (wide angle) side to zoom out or one of the controls on the [TELE]
(telephoto) side to zoom in.
• There are three levels of constant zoom speed - [ ]/[ ] is the slowest and [ ]/[ ] the fastest.
79
Using Optional Conversion Lenses
Using Optional Conversion Lenses
80
You can use the following optional conversion lenses with this camcorder. Before you attach a conversion lens,
perform the procedure below to optimize the autofocus and minimum object distance for the particular
accessory.
Operating modes:
Optional Conversion Lens
Focal Length Factor
Minimum Focusing Distance
TL-H58 Tele-converter
Approx. 1.5x
Approx. 130 cm (4.3 ft.) throughout the zoom range
WA-H58 Wide Attachment
Approx. 0.75x
Approx. 60 cm (2.0 ft.) throughout the zoom range
1 Open the [Conversion Lens] submenu.
[~ Camera Setup]
[~ Camera Setup] > [Conversion Lens]
2 Select [TL-H58] or [WA-H58] and then press SET.
• The image stabilization method, minimum focusing distance and the
approximate distance to the subject displayed on the screen will
change depending on the conversion lens selected.
• Select [Off] if you do not intend to use a conversion lens.
Y
P
O
[Conversion Lens]
[Off]
NOTES
• Even if [~ Camera Setup] > [AF Mode] > [Speed] was set to [High] or [Medium], it will change
automatically to [Normal] when using a conversion lens.
• Vignetting may occur when taking wide angle shots with the optional TL-H58 Tele-converter.
• When [Conversion Lens] is set to [WA-H58], the telephoto end will be more limited than the wide-angle end.
• If you set an assignable button to [TL-H58] or [WA-H58] (A 129), you can press the button to turn on/off the
optimized settings for the selected conversion lens.
C
Adjusting the Focus
Adjusting the Focus
The camcorder offers 3 ways to focus. When you use manual focus, you can use focus assistance functions,
such as peaking and magnification, to help you focus more accurately.
Autofocus (AF): The camcorder continuously adjusts the focus automatically. When using autofocus, you can
one of three levels of AF speed. You can also use the focus ring (with no physical stops).
Push AF: While using MF, Normal AF or Medium AF, you can have the camcorder switch temporarily to Instant
AF mode as long as you hold the PUSH AF button pressed down.
Operating modes:
Autofocus (AF) Mode
The camcorder uses the TTL autofocus system and continuously adjusts the focus on the subject in the center
of the screen. The focusing range is 1 cm (0.39 in.; at full wide-angle, measured from the front of the lens barrel)
to G.
Even during autofocus mode, you can turn the focus ring to focus manually. When you stop turning the ring, the
camcorder returns to autofocus mode. This is useful in situations such as when focusing on a subject on the
other side of a window.
Set the FOCUS switch to A.
C
• = appears on the left of the screen.
Y
P
O
Remote Operation Using Browser Remote
After completing the necessary preparations (A 182), you can change
the focus mode remotely from a connected device using the Browser
Remote application.
Press [MF] on the Browser Remote screen.
• The orange line in the button will turn gray and the camcorder will
change to autofocus mode.
• Press [MF] again to return the camcorder to manual focus mode.
English
Manual focus (MF): Adjust the focus manually using the focus ring, or remotely, using the Browser Remote
application.
81
Adjusting the Focus
Setting the Autofocus Mode
You can select how fast the camcorder focuses using autofocus.
1 Open the AF mode’s [Speed] submenu.
82
[~ Camera Setup]
[~ Camera Setup] > [AF Mode] > [Speed]
2 Select the desired option and then press SET.
Options
[High]:
[Medium]:
[Normal]:
Sets the autofocus mode to Instant AF. The focus is adjusted at
the highest speed. This mode is useful even when recording in
very bright or low-light surroundings. This mode uses both the
TTL system and external sensor for focusing.
Sets the autofocus mode to Medium AF. The camcorder
focuses more smoothly on the subject than when using the
[High] setting.
Sets the autofocus mode to Normal AF. The autofocus
adjustment is made at a stable speed.
[AF Mode]
[Speed]
[High]
NOTES
• When recording in bright surroundings, the camcorder closes down the aperture. This may cause the picture
to appear blurred and is more noticeable toward the wide-angle end of the zoom range. In such case, set
[~ Camera Setup] > [ND Filter] to [Automatic].
• When [~ Camera Setup] > [Conversion Lens] is set to a setting other than [Off] and when the camcorder is
in infrared mode, the [High] and [Medium] settings are not available. Also, Push AF will operate at Normal AF
speed.
• Autofocus takes longer to focus when the frame rate is set to 29.97P or 23.98P than when it is set to 59.94i.
During slow & fast motion recording mode, the same is true for all shooting frame rates other than 60.
• When recording under dark conditions, the focusing range narrows and the picture may appear blurred.
• Autofocus (including Push AF) may not work well on the following subjects or in the following cases. In such
case, focus manually.
- Reflective surfaces
- Subjects with low contrast or without vertical lines
- Fast moving subjects
- Through dirty or wet windows
- Night scenes
C
Y
P
O
Adjusting the Focus
Manual Focus (MF)
Using the Focus Ring
1 Set the FOCUS switch to M.
83
• A appears on the left of the screen.
2 Turn the focus ring on the lens to adjust the focus.
NOTES
• You can use the focus ring to adjust the focus while you are operating
the zoom. If the camcorder was initially in autofocus mode, it will
return to autofocus mode after you adjust the focus manually.
• You can change the direction of the adjustment and the sensitivity of
the response of the focus ring using the [w Other Functions] >
[Custom Function] > [Focus Ring Direction] and [Focus Ring Control]
settings (A 141).
Remote Operation Using Browser Remote
Y
P
O
After completing the necessary preparations (A 182), you can adjust the focus remotely from a connected
device using the Browser Remote application.
1 If the camcorder is set to AF mode, touch [MF] on the Browser Remote screen.
• The gray line in the button will turn orange and the camcorder will change to manual focus mode.
2 Press one of the [FOCUS] controls to adjust the focus as necessary.
C
• Press one of the controls on the [NEAR] side to focus closer or one of the controls on the [FAR] side to focus
farther away.
• There are three levels of adjustment - [ ]/[ ] is the smallest and [ ]/[ ] the largest.
햲
햳
NOTES
• Using the subject distance display on the screen:
- When the camcorder switches out of autofocus mode or while you adjust the focus with the focus ring, the
approximate subject distance is displayed on the screen for approximately 5 seconds.
- Use the subject distance display as an estimate. When the distance reading is not considered very precise
for a particular zoom range, it will be displayed in gray.
- [G] indicates infinity focus and [G–] indicates over infinity focus.
- You can change the units of distance between meters and feet using the [w Other Functions] > [Custom
Function] > [Distance Units] setting (A 141).
English
• Focusing speed will depend on how you operate the focus ring.
Adjusting the Focus
84
- The correct subject distance will not be displayed when an optional conversion lens is attached.
• If you operate the zoom after focusing, the focus on the subject may be lost.
• If you focus manually and then leave the camcorder with the power turned on, the focus on the subject may
be lost after a while. This possible slight shift in focus is a result of the internal temperature rising in the
camcorder and lens. Check the focus before resuming shooting.
• When an optional RC-V100 Remote Controller is connected to the camcorder, you can adjust the focus with
the remote controller’s FOCUS dial. At default settings, turn the dial right to focus farther and left to focus
nearer.
Using the Focus Assistance Functions
In order to focus more accurately, you can use two focus assistance functions – peaking, which creates a clearer
contrast by emphasizing the outlines of the subject, and magnification, which enlarges the image on the screen.
You can use both functions simultaneously for greater effect.
You can also use the [w Other Functions] > [Custom Function] > [Focus Assistance B&W] setting (A 141) to
switch the screen to black & white while using the focus assistance functions.
Peaking
The camcorder offers two peaking levels.
[£ OLED/VF Setup]
1 Press the PEAKING button.
• The peaking icon (J or K) appears at the lower center of the
screen and the outlines in the image will be emphasized, depending
on the focus.
• Press the button again to turn off peaking.
• Alternatively, you can use [£ OLED/VF Setup] > [Peaking] >
[Setting] to turn peaking on and off.
C
2 Open the peaking [Select] submenu to select the
peaking level.
[£ OLED/VF Setup] > [Peaking] > [Select]
3 Select the desired level and then press SET.
Y
P
O
[Peaking]
[Select]
[Peaking 1]
Magnification
1 Press the MAGN. button.
• ^ appears at the lower center of the screen and the center of the screen is magnified approximately
2 times*.
• A white frame representing the whole screen area is displayed on the top right of the screen. The orange
frame within it represents the approximate part of the image shown magnified.
2 If necessary, use the joystick (ÝÞ) to move the orange frame around and check other parts of the image.
• You can move the orange frame 5 steps vertically or horizontally. Press the CANCEL button to return the
magnification frame to the center position.
3 Press the MAGN. button again to cancel the magnification.
* The magnification that appears on the OLED screen and on the viewfinder screen is different. The magnification also differs
based on the video configuration.
Adjusting the Focus
Push AF
While using manual focus (MF, A 83) or autofocus at a [Normal]
or [Medium] speed (Normal AF, Medium AF, A 81), press the
PUSH AF button and hold it pressed down.
• Autofocus is temporarily activated at the highest speed (Instant AF) as
long as you hold the PUSH AF button pressed down.
Y
P
O
NOTES
• All the NOTES for the autofocus section (A 82), apply also to Push
AF.
• Push AF is not available when [~ Camera Setup] > [AF Mode] >
[Face AF] is set to [Face Only] and a face has not been detected in the
picture.
C
Detecting and Focusing On Faces
The camcorder can detect a person’s face during autofocus mode,
automatically focus on it, and even track it if the person moves. When
there are a number of people in the picture, one person (with the white
face detection frame) will be determined to be the main subject and the
camcorder will focus on that person’s face. You can also change the
person selected as main subject.
[~ Camera Setup]
[AF Mode]
[Face AF]
[Off]
1 Open the [Face AF] submenu.
[~ Camera Setup] > [AF Mode] > [Face AF]
2 Select the desired option and then press SET.
•
or
will appear on the left of the screen.
3 Point the camcorder at the subject.
• If there is more than one person in the picture, the camcorder will automatically select one person it
determines is the main subject. The camcorder will indicate the main subject with a white face detection
frame and other faces with gray frames.
• If necessary, push the joystick left/right to change the main subject when there is more than one person.
85
English
NOTES
• Peaking/Magnification appears only on the camcorder screen. It will not appear on an external monitor
connected to the camcorder and will not affect your recordings.
• You can use the [£ OLED/VF Setup] > [Peaking] > [Peaking 1] and [Peaking 2] settings to set the color,
gain and frequency of the two peaking levels independently of each other.
• When using the camcorder’s screen to focus:
- The camcorder features professional video scopes (A 108). You can display the edge monitor to help you
focus even more accurately.
- You can use peaking together with the edge monitor. In such case, the gain and frequency of the peaking
effect will be adjusted automatically according to the gain settings of the edge monitor.
Adjusting the Focus
Options
[Face Priority]
86
[Face Only]
[Off]:
: When there is no face detected, the camcorder focuses automatically on the subject at the center of
the screen.
: When there is no face detected, the camcorder is set to manual focus.
Standard autofocus operation with no face detection.
NOTES
• The camcorder may mistakenly detect the faces of non-human subjects. In such case, turn face detection off.
• In certain cases, faces may not be detected correctly. Typical examples include:
- Faces extremely small, large, dark or bright in relation to the overall picture.
- Faces that are turned to the side, at a diagonal or partially hidden.
• Face detection cannot be used in the following cases:
- When the shutter speed used is slower than 1/30 (1/24 if the frame rate is set to 23.98P).
- When using slow & fast motion recording mode and the shooting frame rate is set to less than 24.
- In manual focus mode while you hold the PUSH AF button pressed down.
- During real-time proxy transfer mode or infrared mode.
• When a subject’s face is detected, the camcorder adds an event mark to the frame (MXF clips only). You can
then use Canon XF Utility to search for event marks in the MXF clip.
• If you set an assignable button to [Face AF] (A 129), you can press the button to toggle between the face
detection options.
Focus Limit and Macro Shooting
C
Y
P
O
By default, the camcorder’s focus range allows macro shooting. You can
activate the focus limit to restrict the focus range. The focus range 1 cm
(0.39 in.; at full wide-angle) to G is limited to 60 cm (2 ft.) to G
(throughout the entire zoom range).
1 Open the [Focus Limit] submenu.
[~ Camera Setup] > [Focus Limit]
[~ Camera Setup]
[Focus Limit]
[Off]
2 Select [On] and then press SET.
• Select [Off] to enable macro shooting.
NOTES
• If you set an assignable button to [Focus Limit] (A 129), you can press the button to turn the focus limit on/
off.
Image Stabilizer
Image Stabilizer
Use the image stabilizer to compensate for camcorder shake in order to achieve steadier shots. There are 3
methods of image stabilization; select the method that best suits your needs.
Dynamic IS Ä: Dynamic IS compensates for a higher degree of camcorder shake, such as when shooting
while walking, and is more effective as the zoom approaches full wide angle.
Powered IS Ç: Powered IS is most effective when you are stationary and zooming in on far subjects using high
zoom ratios (the more you approach the telephoto end). This mode is not suitable for tilting and panning shots.
Operating modes:
To activate Dynamic IS or Standard IS
1 Open the OIS functions [Select] submenu.
[~ Camera Setup]
[~ Camera Setup] > [OIS Functions] > [Select]
2 Select [Img Stab.] and then press SET.
Y
P
O
• Select [Off] instead to turn off the image stabilization, for example,
when recording with the camcorder mounted on a tripod.
3 Open the [Image Stabilizer] submenu.
[~ Camera Setup] > [OIS Functions] > [Image Stabilizer]
[OIS Functions]
[Select]
[Img Stab.]
4 Select [Dynamic] or [Standard] and then press SET.
• The icon of the selected mode appears on the bottom of the screen.
To activate Powered IS
C
Press the POWERED IS button to activate Powered IS.
• The Powered IS icon (Ç) appears on the bottom of the screen.
• Press the POWERED IS button again to return the camcorder to the
image stabilization method set in the menu.
• Powered IS can be used even when [~ Camera Setup] > [OIS
Functions] > [Select] is set to [Off].
•
•
•
•
NOTES
If you set an assignable button to [Img Stab.] (A 129), you
can press the button to turn the selected image stabilization
method on or off.
If the degree of camcorder shake is too high, the image
stabilizer may not be able to compensate fully.
When using Dynamic IS, the edges of the picture may be
adversely affected (ghosting, artifacts and/or dark areas
may appear) when compensating for a high degree of
camcorder shake.
When [~ Camera Setup] > [Wide-End Angle] is set to
[Wider], [Image Stabilizer] will change automatically to
[Standard] and it cannot be changed.
[~ Camera Setup]
[OIS Functions]
[Image Stabilizer]
[Standard]
English
Standard IS Å: Standard IS compensates for a lower degree of camcorder shake, such as when shooting
while remaining stationary, and is suitable for shooting natural-looking scenes.
87
Onscreen Markers and Zebra Patterns
Onscreen Markers and Zebra Patterns
88
Using onscreen markers allows you to make sure your subject is correctly framed and is within the appropriate
safe area. The zebra patterns help you identify areas that are overexposed. The onscreen markers and zebra
pattern will not affect your recordings.
Operating modes:
Displaying Onscreen Markers
[£ OLED/VF Setup]
The camcorder offers 5 types of onscreen markers. You can display
multiple onscreen markers simultaneously.
[Markers]
1 Open the [Markers] submenu.
[£ OLED/VF Setup] > [Markers]
2 Select a marker you wish to display, select [Black] or [Gray] and
then press SET.
Y
P
O
• Select [Off] to turn off the selected marker.
• You can display multiple markers simultaneously. Repeat this step as
necessary.
• If you selected [Safe Area] or [Aspect Marker], continue to step 3.
Otherwise, you can skip to step 4.
[Center]
[Horizontal]
[Grid]
[Safe Area]
[Aspect Marker]
[Off]
3 Select [Safe Area Setting] or [Aspect Ratio], select the desired option and then press SET.
C
4 Select [Enable], select [On] and then press SET to enable the onscreen markers.
• All of the selected onscreen markers will be displayed.
• Select [Off] to turn off all onscreen markers.
Options
[Center]:
[Horizontal]:
[Grid]:
[Safe Area]:
Displays a small marker that indicates the center of the screen.
Displays a horizontal line to help you compose level shots.
Displays a grid that allows you to frame your shots correctly (horizontally and vertically).
Displays indicators that show various safe areas, such as the action safe area and text safe area.
Available options for [Safe Area Setting] are [80%], [90%], [92.5%] and [95%].
[Aspect Marker]: Displays markers that indicate various aspect ratios to help you keep your shot within that area.
Available options for [Aspect Ratio] are [4:3], [13:9], [14:9], [1.66:1], [1.75:1], [1.85:1] and [2.35:1].
Safe area 80%
Level marker
Aspect ratio 4:3
Onscreen Markers and Zebra Patterns
Grid
89
Center marker
English
NOTES
• You can turn off all other onscreen displays, leaving only the onscreen markers (A 53).
• If you set an assignable button to [Markers] (A 129), you can press the button to turn the onscreen markers
on/off.
Displaying Zebra Patterns
Y
P
O
The camcorder has a zebra pattern feature that shows black and
white diagonal stripes over areas that are overexposed. This is
displayed only on the screen and will not affect your recordings.
There are two types of zebra patterns and you can display both
simultaneously. Zebra 1 lets you identify areas within a certain
range (±5% of a specified level) while zebra 2 lets you identify
areas that are over a specified level. When you display both
simultaneously and they overlap, only zebra 1 will be displayed in
those areas.
C
1 Open the zebra pattern [Select] submenu.
[£ OLED/VF Setup] > [Zebra] > [Select]
2 Select [Zebra 1], [Zebra 2] or [Zebra 1&2] and then press
SET.
3 Open the zebra level submenu.
[£ OLED/VF Setup] > [Zebra] > [Zebra 1 Level] or [Zebra
2 Level]
4 Select a zebra level, press SET and then press MENU to
close the menu.
5 Press the ZEBRA button to turn the selected zebra
pattern on/off.
[£ OLED/VF Setup]
[Zebra]
[Select]
[Zebra 1]
• Alternatively, you can use the [£ OLED/VF Setup] >
[Zebra] > [Setting] setting to turn the zebra pattern on/off.
NOTES
• You can use the [£ OLED/VF Setup] > [Zebra] > [HD Output] setting to display the zebra pattern on an
external monitor connected to the MON. terminal (
, HD output only) or HDMI OUT terminal (HD output
only).
Setting the Time Code
Setting the Time Code
90
In
mode, the camcorder can generate a time code signal and embed it in MXF clips. You can have the
camcorder output the time code signal from the 3G/HD-SDI terminal*, MON. terminal* or TIME CODE terminal*
(A 96). In
mode, you can output the time code of the MXF clip being played back through the same
terminals. Additionally, you can superimpose the time code on video output from the MON. terminal*, HDMI OUT
terminal or AV OUT terminal. When using a frame rate other than 23.98P, you can also select between a drop
frame and non-drop frame time code.
To synchronize the camcorder’s time code to an external time code generator, refer to Synchronizing
with an External Device (A 94).
*
only.
Selecting the Running Mode
You can select the running mode of the camcorder’s time code.
[¤ TC/UB Setup]
[Time Code]
Operating modes:
1 Open the time code [Mode] submenu.
[¤ TC/UB Setup] > [Time Code] > [Mode]
Y
P
O
2 Select the desired option and then press SET.
• If you selected [Regen.], you do not need to perform the rest of this
procedure. If you selected [Preset] and would like to set the time
code’s initial value, see the following section Setting the Time Code’s
Initial Value.
C
3 After you select [Preset], open the time code [Run] submenu.
[¤ TC/UB Setup] > [Time Code] > [Run]
[Mode]
[Preset]
[¤ TC/UB Setup]
[Time Code]
[Run]
4 Select the desired option and then press SET.
Options
[Preset]:
[Regen.]:
[Rec Run]
The time code starts from an initial value you can select in
advance. The default initial time code is 00:00:00.00. The time code’s running mode depends on the
[Run] setting.
[Rec Run]: The time code runs only while recording so MXF clips recorded consecutively on the same
CF card will have continuous time codes.
[Free Run]: The time code starts running the moment you press SET to select this option and keeps
running regardless of the camcorder’s operation.
The camcorder will read the selected CF card and the time code will continue from the last recorded time
code on the CF card. The time code runs only while recording so MXF clips recorded consecutively on
the same CF card will have continuous time codes.
Setting the Time Code’s Initial Value
If you set the time code mode to [Preset], you can set the initial value of
the time code.
[¤ TC/UB Setup]
[Time Code]
1 Open the time code [Setting] submenu.
[¤ TC/UB Setup] > [Time Code] > [Setting]
[Setting]
2 Select [Set] and then press SET.
• The time code setting screen appears with an orange selection frame indicating the hours.
Setting the Time Code
• To reset the time code to [00:00:00.00], select [Reset] instead. If the running mode is set to [Free Run], the
time code will be reset the moment you press SET and keep running continuously from 00:00:00.00.
3 Push the joystick up/down to set the hours and then press SET to move to the minutes.
4 Change the rest of the fields (minutes, seconds, frame) in the same way.
• Press the CANCEL button to close the screen without setting the time code.
91
Selecting Drop or Non-Drop Frame
You can select between a drop frame (DF) or non-drop frame (NDF) time
code, depending on how you plan to use your recordings. However, when
the frame rate is set to 23.98P, the time code is set to non-drop frame
(NDF) and cannot be changed.
[¤ TC/UB Setup]
[Time Code]
[DF/NDF]
Operating modes:
1 Open the [DF/NDF] submenu.
Y
P
O
[DF]
[¤ TC/UB Setup] > [Time Code] > [DF/NDF]
2 Select [DF] or [NDF] and then press SET.
• The time code display will differ depending on the setting. When you select [DF], the time code will appear
as [00:00:00.00]; when you select [NDF], it will appear as [00:00:00:00].
C
Putting the Time Code Display on Hold
If you set an assignable button to [Time Code Hold] (A 129), you can press the button to freeze the display of
the time code*. While the time code display is put on hold, [H] will appear on the screen next to the time code.
The time code continues to run normally while the time code display is on hold. When you resume the time code
display, the current time code will be displayed.
* The time code signal output from the 3G/HD-SDI terminal or TIME CODE terminal (both
only) will not be put on hold. The
time code superimposed on the video signal output from MON. terminal (
only), HDMI OUT terminal and AV OUT terminal
will be put on hold.
Operating modes:
About the Time Code Display
An icon may appear next to the time code depending on the operation. Refer to the following table.
Icon
Description
R
The time code is set to [Regen.].
P
The time code is set to [Preset] and the running mode is set to [Rec Run].
F
The time code is set to [Preset] and the running mode is set to [Free Run].
E
Time code signal is coming from an external source.
H
Time code display is on hold.
No icon
Time code during clip playback.
English
5 Select [Set] and then press SET to close the screen.
• If the running mode is set to [Free Run], the time code will start running from the selected time code the
moment you press SET.
Setting the Time Code
92
NOTES
• The frames value of the time code runs from 0 to 23 (frame rate set to 23.98P) or from 0 to 29 (all other frame
rates).
•
However, when [¤ TC/UB Setup] > [Time Code] > [XF Legacy Sync] is set to [On], even when
the frame rate is set to 23.98P, the frames value of the time code output from the TIME CODE terminal will run
from 0 to 29.
• When you are using interval recording, frame recording or slow & fast motion recording mode, you cannot
select the [Free Run] running mode. Conversely, when you are using pre-recording mode and when the movie
format is set to MXF+MP4, [Free Run] is set automatically and cannot be changed.
• When you mix drop frame and non-drop frame time codes, there might be a discontinuity in the time code at
the point where the recording starts.
• When you are using the [Free Run] running mode, the time code will continue running as long as the built-in
rechargeable lithium battery is charged, even if you disconnect all other power sources. However, this is less
accurate than when the camcorder is on.
• If you set an assignable button to [Time Code] (A 129), you can press the button to open the
[¤ TC/UB Setup] > [Time Code] submenu.
C
Y
P
O
Setting the User Bit
Setting the User Bit
*
[¤ TC/UB Setup]
93
[User Bit]
[Type]
[Setting]
only.
Operating modes:
1 Open the user bit [Type] submenu.
[¤ TC/UB Setup] > [User Bit] > [Type]
2 Select the desired user bit type and then press SET.
Y
P
O
• Select [Setting] to set your own identification code, [Time] to use the time as user bit, or [Date] to use the
date as the user bit.
• If you selected [Time] or [Date], you do not need to perform the rest of the procedure. If you selected
[Setting], continue the procedure to set the identification code.
3 Select [Set] and then press SET.
• The user bit setting screen appears with an orange selection frame on the leftmost character.
• To reset the user bit to [00 00 00 00], select [Reset] instead.
C
4 Push the joystick up/down to select the first character and then press SET to move to the next
character.
• Change the rest of the characters in the same way.
• Press the CANCEL button to close the screen without setting the user bit.
5 Select [Set] and then press SET to close the screen.
English
The user bit display can be selected from the date or the time of
recording, or an identification code consisting of 8 characters in the
hexadecimal system. There are sixteen possible characters: the numbers
0 to 9 and the letters A to F.
In addition to being recorded with MXF clips, the user bit information can
be output along with the video signal output from the 3G/HD-SDI
terminal*, MON. terminal*, TIME CODE terminal* or HDMI OUT terminal.
Conversely, if user bit information is being received along with an external
time code, you can also record the external user bit on the recording
media.
Synchronizing with an External Device
Synchronizing with an External Device
94
Using Genlock synchronization, you can synchronize this camcorder’s video signal to that of an external video
device. Similarly, using an external time code signal, you can synchronize this camcorder’s time code to the
external signal. Using the external time code signal with multiple cameras allows you to set up a multi-camera
recording. You can also output the time code signal from this camcorder to achieve the same result. If you
output the time code from the 3G/HD-SDI terminal to an editing device, the editor can create video with the
same time code.
Connecting an External Device
When synchronizing the camcorder to an external signal*, use the GENLOCK/SYNC OUT terminal. When
synchronizing a time code signal, use the TIME CODE terminal. Be sure to set either terminal to input or output
in advance.
Connect the external device to the camcorder as shown in the following diagram.
* As reference video signal (input signal) for Genlock synchronization, you can use an analog blackburst or tri-level signal.
Connection Diagram
Y
P
O
GENLOCK/SYNC OUT terminal
C
TIME CODE terminal
Reference Video Signal Input (Genlock Synchronization)
When a reference sync signal (analog blackburst or tri-level signal) is input through the GENLOCK/SYNC OUT
terminal, the phases of the camcorder’s V and H sync will automatically be synchronized to it. The phase
difference between the external Genlock signal and the camcorder is initially set to 0. The H phase can be
adjusted within the range of approximately ±0.4 H.
Operating modes:
1 Open the [GENLOCK/SYNC OUT] submenu.
• [¢ Video Setup] > [GENLOCK/SYNC OUT]
2 Select [Genlock] and then press SET.
[¢ Video Setup]
[GENLOCK/SYNC OUT]
3 Open the [Genlock Adjustment] submenu.
[w Other Functions] > [Genlock Adjustment]
[Genlock]
4 Adjust the H phase to the desired level (-1023 to 1023), select
[Set] and then press SET.
• Push the joystick up/down to select the value for each field and then
press SET to move to the next field.
[w Other Functions]
[Genlock Adjustment]
Synchronizing with an External Device
Time Code Signal Input
An external SMPTE-standard LTC timing signal received from the TIME
CODE terminal will be recorded as the time code. The user bit of the
external timing signal can also be recorded with MXF clips. Before
connecting the device, set the TIME CODE terminal to input. Also, you
must set the running mode of the time code to [Free Run] (A 90).
Operating modes:
1 Open the [TC In/Out] submenu.
Y
P
O
[¤ TC/UB Setup]
[Time Code]
[TC In/Out]
[In]
[¤ TC/UB Setup] > [Time Code] > [TC In/Out]
2 Select [In] and then press SET.
C
Recording the User Bit of an External Signal
The user bit of an external time code signal can also be recorded with
MXF clips along with the time code itself.
[¤ TC/UB Setup]
[User Bit]
1 Open the user bit [Recording Mode] submenu.
[¤ TC/UB Setup] > [User Bit] > [Recording Mode]
[Recording Mode]
2 Select [External] and then press SET.
•
•
•
•
[Internal]
NOTES
The camcorder will synchronize with an external time code that has the
same frequency as that used for recording. However, when the frame rate is set to 23.98P, you can
synchronize instead to a 30-frame time code signal by setting [¤ TC/UB Setup] > [Time Code] > [XF
Legacy Sync] to [On].
When a suitable time code signal is received, the camcorder’s own time code will be synchronized to it and the
synchronization will be maintained even if you disconnect the cable from the TIME CODE terminal. However,
performing any of the following actions while the cable is not connected will cause the synchronization to be
disrupted; the correct time code will be restored once you reconnect the cable.
- Turning the camcorder off/on
- Changing the operating mode to
mode
- Changing the video configuration
If the external time code signal is incorrect or there is no input signal, the internal time code set in the
[¤ TC/UB Setup] > [Time Code] submenu will be recorded instead.
While a time code signal is being received, the external time code’s drop-frame bit will be used.
95
English
NOTES
• When [¢ Video Setup] > [3G/HD-SDI] is set to [Direct], the camcorder will synchronize with a Genlock
signal that has the same frequency as that used for recording. However, when in addition to that, the frame
rate is set to 23.98P, you can synchronize instead to an external 29.97 Hz or 59.94 Hz signal by setting
[¤ TC/UB Setup] > [Time Code] > [XF Legacy Sync] to [On].
• When a suitable Genlock signal is input, the Genlock synchronization stabilizes after approximately
10 seconds.
• When a suitable Genlock signal is detected, the U icon will flash on the upper right of the screen. When the
camcorder locks on the external Genlock signal, the icon will stay on.
• If the external Genlock signal is incorrect, the synchronization may not be stable. In such case, the recorded
time code may be incorrect.
Synchronizing with an External Device
Reference Video Signal Output
96
After changing the GENLOCK/SYNC OUT terminal’s function to [SYNC Output], you can output the camcorder’s
video signal as a reference sync signal (HD tri-level signal) to synchronize an external device to this camcorder.
The reference video signal output will have the same frequency as the signal output from the 3G/HD-SDI
terminal.
Operating modes:
1 Open the [GENLOCK/SYNC OUT] submenu.
[¢ Video Setup]
[¢ Video Setup] > [GENLOCK/SYNC OUT]
2 Select [SYNC Output] and then press SET.
[GENLOCK/SYNC OUT]
• If necessary, change the scan mode (P or PsF) with the [¢ Video
Setup] > [SYNC Scan Mode] setting.
• If necessary to synchronize with older XF camcorders, you can
change the reference output signal with the [¤ TC/UB Setup] >
[Time Code] > [XF Legacy Sync] setting.
Synchronization signals
Frame rate
mode
[XF Legacy Sync]1 set to
[Off]
59.94i / 59.94P
1920x1080
29.97 (P/PsF)
23.98P
59.94P
1280x720
29.97P
23.98P
1
2
Y
P
O
Signal output from the GENLOCK/SYNC OUT terminal
Video output from the 3G/HD-SDI terminal
Resolution
[Genlock]
[XF Legacy Sync]1 set to
[On]
mode
1080/59.94i
1080/29.97 (P/PsF)2
C
1080/59.94i
1080/59.94i
720/59.94P
720/59.94P
1080/23.98 (P/PsF)2
720/59.94P
720/29.97P
720/23.98P
[¤ TC/UB Setup] > [Time Code] > [XF Legacy Sync].
You can select P or PsF output with the [¢ Video Setup] > [SYNC Scan Mode] setting.
Time Code Signal Output
The time code will be output from the TIME CODE terminal as an SMPTE-standard LTC timing signal. The user
bit will also be output. Before connecting the device, set [¤ TC/UB Setup] > [Time Code] > [TC In/Out] to
[Out] to change the TIME CODE terminal to output (A 95).
The embedded time code will be output also from the 3G/HD-SDI terminal and the MON. terminal. Additionally,
you can set [¢ Video setup] > [HDMI Time Code] to [On], to output the embedded time code also from the
HDMI OUT terminal.
Operating modes:
NOTES
• The camcorder will output a time code that has the same frequency as that used for recording. When the
frame rate is set to 23.98P, you can output instead a 30-frame time code signal by setting [¤ TC/UB
Setup] > [Time Code] > [XF Legacy Sync] to [On].
Synchronizing with an External Device
• The user bit of the time code signal is output while the camcorder is recording MXF clips in
mode or
during playback of MXF clips in
mode. When the frame rate is set to 23.98P and [¤ TC/UB Setup]
> [User Bit] > [Output Mode] is set to [Pulldown], the signal is converted to 59.94i / 59.94P using the 2:3
pulldown method. An external device can receive the data used in this conversion (2:3 pulldown data) to
convert the signal to the original 1080/23.98P specifications.
97
English
C
Y
P
O
Recording Audio
Recording Audio
98
The camcorder features 4-channel or 2-channel linear PCM audio recording and playback for MXF clips and
2-channel AAC audio recording and playback for MP4 clips. The sampling frequency is 48 kHz for all audio
recording modes. You can record audio using commercially available microphones (INPUT 1/INPUT 2 terminal,
MIC terminal), line input (INPUT 1/INPUT 2 terminal) or the built-in microphone.
The same audio channels that are being recorded in the camcorder can also be output with the video signal from
the 3G/HD-SDI terminal* or MON. terminal*. You can record this audio signal on an external recorder.
*
only.
Operating modes:
Audio Settings and Recorded Audio Channels
Which audio inputs are recorded to which audio channels is determined by a combination of menu settings,
audio-related controls on the camcorder and whether an external microphone is connected to the MIC terminal.
The following table gives an overview of the possible combinations.
For MXF clips, all the combinations listed are available. For MP4 clips, when the movie format is set to MP4 or to
MXF+MP4 using 2-channel audio recording, only the combinations marked as A are available. When the movie
format is set to MXF+MP4 using 4-channel audio recording, with the [¡ Audio Setup] > [Audio Input] >
[MP4 Channels] setting you can select which two channels of the four (B or C) to record with the MP4 clip.
2-channel audio recording
Menu settings
[4-Channel
Input]1
[CH2 Input]
AUDIO IN selection switches
2
CH1
[INPUT 2]
MIC terminal
used
C
CH2
Y
P
O
Recorded audio channels/
audio sources
CH1
INPUT 2
terminal
(XLR)
–
INPUT 2
[INPUT 1]
–
INPUT 1
INPUT 1
terminal
(XLR)
–
INPUT 1
terminal
(XLR)
No
Built-in
microphone
(monaural)
Yes
MIC terminal
(monaural)
INT.MIC/MIC
[Off] (2)
CH2
No
Built-in
microphone
(monaural)
Yes
MIC terminal
(monaural)
No
Built-in
microphone
(L)
Built-in
microphone
(R)
Yes
MIC terminal
(L)
MIC terminal
(R)
INPUT 2
INT.MIC/MIC
INT.MIC/MIC
INPUT 2
terminal
(XLR)
A
Recording Audio
4-channel audio recording
Menu settings
[4-Channel
Input]1
[CH2 Input]2
AUDIO IN selection switches
CH1
CH2
MIC terminal
used
Recorded audio channels/audio sources
CH1
CH2
CH4
Built-in
microphone
(L)
Built-in
microphone
(R)
MIC terminal
(L)
MIC terminal
(R)
Built-in
microphone
(L)
Built-in
microphone
(R)
MIC terminal
(L)
MIC terminal
(R)
Built-in
microphone
(monaural)
Built-in
microphone
(L)
Built-in
microphone
(R)
MIC terminal
(monaural)
MIC terminal
(L)
MIC terminal
(R)
Built-in
microphone
(L)
Built-in
microphone
(R)
MIC terminal
(L)
MIC terminal
(R)
Built-in
microphone
(L)
Built-in
microphone
(R)
No
INPUT 2
terminal
(XLR)
[INPUT 2]
Yes
INPUT 1
INPUT 2
No
INPUT 1
terminal
(XLR)
INPUT 1
terminal
(XLR)
[INPUT 1]
Yes
No
[On] (4)
INPUT 1
INT.MIC/MIC
Yes
–
INPUT 2
INT.MIC/MIC
C
INT.MIC/MIC
INPUT 1
terminal
(XLR)
Y
P
O
No
Built-in
microphone
(monaural)
Yes
MIC terminal
(monaural)
No
Built-in
microphone
(L)
Built-in
microphone
(R)
Yes
MIC terminal
(L)
MIC terminal
(R)
INPUT 2
terminal
(XLR)
B
C
1
[¡ Audio Setup] > [Audio Input] > [4-Channel Input]. The number in parentheses indicates the number of audio channels
recorded.
2 [¡ Audio Setup] > [Audio Input] > [CH2 Input].
NOTES
• On the [Audio] status screen (A 211), you can check the audio level adjustment mode and input source for
each of the audio channels.
99
English
CH3
Recording Audio
Selecting the Number of Recorded Audio Channels
100
You can select how many audio channels (2 or 4) will be recorded with MXF clips. Since MP4 clips can only
record 2 audio channels, when the movie format is set to MXF+MP4 using 4-channel audio recording, you can
select which 2 audio channels will be recorded with the MP4 clip.
Operating modes:
1 Open the [4-Channel Input] submenu.
[¡ Audio Setup] > [Audio Input] > [4-Channel Input]
2 Select [On] for 4-channel audio recording or [Off] for 2-channel
audio recording and then press SET.
• During 4-channel audio recording,
screen.
will appear on the right of the
[¡ Audio Setup]
[Audio Input]
[4-Channel Input]
[Off]
Selecting the Audio Channels for MP4 Clips
Operating modes:
1 Open the [MP4 Channels] submenu.
Y
P
O
[¡ Audio Setup] > [Audio Input] > [MP4 Channels]
2 Select [CH1/CH2] or [CH3/CH4] and the press SET.
C
[¡ Audio Setup]
[Audio Input]
[MP4 Channels]
[CH1/CH2]
Connecting an External Microphone or External Audio Input Source to the Camcorder
To each of the INPUT terminals you can attach commercially available microphones or analog line in sources with
an XLR connector. To the MIC terminal you can attach commercially available condenser microphones with their
own power supply, and a ∅ 3.5 mm stereo mini plug. When using an external microphone, you can use the
camcorder’s microphone holder.
Follow the procedure below to attach a microphone (refer also to the following illustration). To connect an
external device to the camcorder, plug the device’s cable into the camcorder’s XLR terminal (햵).
1 Loosen the microphone lock screw (햲), open the microphone holder and insert the microphone (햳).
2 Tighten the lock screw and put the microphone cable through the microphone cable clamp under
the microphone holder (햴).
3 Plug the microphone cable into the desired INPUT terminal (햵) or the MIC terminal (햶).
Recording Audio
햲
101
햳
English
Microphone
lock screw
햵
INPUT 1/INPUT 2
terminals
햴
햶 MIC terminal
C
Y
P
O
Using the Built-in Microphone or MIC Terminal
Set the AUDIO IN selection switch of the desired channel
to INT.MIC/MIC.
• If you connect a microphone to the MIC terminal while the
AUDIO IN switch is set to INT.MIC/MIC, the camcorder will
switch automatically from the built-in microphone to the
external microphone.
Cable clamp
Recording Audio
Selecting the Microphone’s Low-Cut Filter
The setting is separate for the built-in microphone and for an external
microphone connected to the MIC terminal.
102
1 Open the [Int. Mic Low Cut] or [MIC Low Cut] submenu.
[¡ Audio Setup] > [Audio Input] > [Int. Mic Low Cut] or
[MIC Low Cut]
[¡ Audio Setup]
[Audio Input]
[Int. Mic Low Cut]
[MIC Low Cut]
2 Select the desired option and then press SET.
[Off]
Options
[Off]:
For recording audio under usual conditions.
[LC1]*:
For recording mainly people’s voices.
[LC2]*, [On]**: For reducing the background sound of wind when recording outdoors in windy surroundings (for
example, on a beach or close to buildings). Note that when you use this setting some low-frequency
sounds may be suppressed along with the sound of wind.
* Only for [Int. Mic Low Cut].
** Only for [MIC Low Cut].
Selecting the Built-in Microphone’s Sensitivity
1 Open the [Int. Mic Sensitivity] submenu.
Y
P
O
[¡ Audio Setup] > [Audio Input] > [Int. Mic Sensitivity]
[¡ Audio Setup]
[Audio Input]
2 Select the desired option and then press SET.
Options
[Normal]:
[High]:
For recording audio under usual conditions.
For recording audio at a higher volume (+6 dB).
C
Activating the Microphone Attenuator
If the audio level is too high and the sound sounds distorted when
recording with the built-in microphone or an external microphone
connected to the MIC terminal, activate the microphone attenuator (12 dB
for the built-in microphone, 20 dB for an external microphone).
1 Open the [Int. Mic Att.] or [MIC Att.] submenu.
[¡ Audio Setup] > [Audio Input] > [Int. Mic Att.] or [MIC Att.]
2 Select [On] and then press SET.
[Int. Mic Sensitivity]
[Normal]
[¡ Audio Setup]
[Audio Input]
[Int. Mic Att.]
[MIC Att.]
[Off]
Recording Audio
Using the INPUT 1/INPUT 2 Terminals
Using the INPUT 1/INPUT 2 terminals, you can record audio independently to two audio channels from a
microphone or analog audio input source.
1 Set the AUDIO IN selection switch for CH1 to INPUT 1
and the AUDIO IN selection switch for CH2 to INPUT 2.
CH1/CH2
– dials
• To supply a microphone with phantom power, set the
switch to MIC+48V instead. Make sure to connect the
microphone first, before turning the phantom power on.
Keep the microphone connected when turning off the
phantom power.
IMPORTANT
• When connecting a microphone or device that does not
support phantom power, make sure to set the INPUT 1/
INPUT 2 switch to MIC or LINE, respectively. If you set the
switch to MIC+48V, the microphone or device may be
damaged.
C
CH1/CH2 audio
level switches
INPUT 1/INPUT 2
audio source
selection switches
AUDIO IN selection
switches
Y
P
O
Recording a Single Audio Input to Two Audio
Channels
By default, each XLR audio input is recorded to a separate audio channel
(INPUT 1 to CH1 and INPUT 2 to CH2). If necessary (for example, as an
audio backup recording), you can the audio input into the INPUT 1
terminal to both audio channels, CH1 and CH2. In that case, you can
adjust the audio recording levels of each channel independently of each
other.
[¡ Audio Setup]
[Audio Input]
[CH2 Input]
[INPUT 2]
1 Open the [CH2 Input] submenu.
[¡ Audio Setup] > [Audio Input] > [CH2 Input]
2 Select the desired option and then press SET.
Options
[INPUT 2]:
[INPUT 1]:
Records audio to each channel separately. Audio input into INPUT 1 is recorded to CH1, while audio
input into INPUT 2 is recorded to CH2.
Audio input into INPUT 1 is recorded to both channels. Audio input into INPUT 2 will not be recorded.
English
2 To select the audio source, set the INPUT 1 or INPUT 2
switch to LINE or MIC as necessary.
103
Recording Audio
Selecting the Microphone’s Sensitivity
When the AUDIO IN selection switch is set to INPUT 1 or INPUT 2 and the corresponding INPUT 1/INPUT 2
switch is set to MIC or MIC+48V, you can select the microphone sensitivity of the external microphone.
104
1 Open the desired INPUT terminal’s sensitivity submenu.
[¡ Audio Setup] > [Audio Input] > [INPUT 1 Mic Trimming] or [INPUT 2 Mic Trimming]
2 Select the desired level and then press SET.
Available Sensitivity Levels
+12 dB
+6 dB
0 dB
-6 dB
[¡ Audio Setup]
-12 dB
[Audio Input]
[INPUT 1 Mic Trimming]
[INPUT 2 Mic Trimming]
[0 dB]
Activating the Microphone’s Attenuator
Y
P
O
When the AUDIO IN selection switch is set to INPUT 1 or INPUT 2 and the
corresponding INPUT 1/INPUT 2 switch is set to MIC or MIC+48V, you
can activate the external microphone's attenuator (20 dB).
1 Open the desired INPUT terminal’s microphone attenuator
submenu.
C
[¡ Audio Setup] > [Audio Input] > [INPUT 1 Mic Att.] or [INPUT
2 Mic Att.]
2 Select [On] and then press SET.
[¡ Audio Setup]
[Audio Input]
[INPUT 1 Mic Att.]
[INPUT 2 Mic Att.]
[Off]
Recording Audio
Adjusting the Audio Level
For CH1 and CH2, you can set the audio recording level to automatic or manual adjustment separately for each
channel. However, when the AUDIO IN selection switches for CH1 and CH2 are both set to INT.MIC/MIC (built-in
microphone or external microphone connected to the MIC terminal), the audio recording level settings for CH1
are applied also to CH2.
Set the audio level switch of the desired channel to A
(automatic) to let the camcorder automatically adjust that
channel’s audio level.
NOTES
• When both CH1 and CH2 are set to record audio input from
the INPUT 1/INPUT terminals and both INPUT 1 and INPUT 2
switches are set to the same audio source (external
microphone or external line input), if the audio level for both
channels is set to automatic, you can use the [¡ Audio
Setup] > [Audio Input] > [INPUT 1&2 ALC Link] setting to
link the audio level adjustment of both channels.
Y
P
O
CH1/CH2: Manual Audio Level Adjustment
You can set the audio level for each channel manually from -G
to 18 dB.
1 Set the audio level switch of the desired channel to M.
C
2 Turn the corresponding – dial to adjust the audio level.
• For reference, 0 corresponds to -G, 5 corresponds to
0 dB, and 10 corresponds to +18 dB.
• As a guideline, adjust the audio recording level so that the
audio level meter on the screen will go to the right of the
-18 dB mark (one mark right of the -20 dB mark) only
occasionally.
• Closing the protective cover will prevent the audio controls
from being changed inadvertently.
English
CH1/CH2: Automatic Audio Level Adjustment
105
Recording Audio
CH3/CH4: Audio Level Adjustment
106
The audio level for CH3 and CH4 can only be adjusted when [¡ Audio
Setup] > [Audio Input] > [4-Channel Input] is set to [On] (4-channel
audio recording). The audio recording level settings are common to both
CH3 and CH4.
[¡ Audio Setup]
[Audio Input]
1 Open the [CH3/CH4 Mode] submenu.
[CH3/CH4 Mode]
[¡ Audio Setup] > [Audio Input] > [CH3/CH4 Mode]
2 Select [Automatic] or [Manual] and then press SET.
• If you selected [Automatic], you do not need to perform the rest of the
procedure. If you selected [Manual], continue the procedure to set the
audio recording level.
[Automatic]
[¡ Audio Setup]
3 Open the [CH3/CH4 Level] submenu.
[¡ Audio Setup] > [Audio Input] > [CH3/CH4 Level]
[Audio Input]
4 Push the joystick up/down to set the audio recording level and
then press SET.
• As a guideline, adjust the audio recording level so that the audio level
meter on the screen will go to the right of the -18 dB mark (one mark
right of the -20 dB mark) only occasionally.
Y
P
O
[CH3/CH4 Level]
[50]
NOTES
• When recording audio input from the INPUT 1/INPUT 2 terminals, if either CH1 or CH2 is set to manual audio
level adjustment, you can also activate the audio peak limiter to prevent audio distortions. When activated, the
audio peak limiter will limit the amplitude of audio input signals when they exceed -6 dBFS. Use the [¡ Audio
Setup] > [Audio Input] > [INPUT 1&2 Limiter] setting.
• We recommend using headphones when adjusting the audio level. If the input level is too high, audio may
become distorted even if the audio level indicator shows an appropriate level.
• If you set an assignable button to [Audio Level] (A 129), you can press the button to turn the onscreen audio
level indicator on and off.
C
Monitoring the Audio with Headphones
You can connect to the × (headphone) terminal any pair of
headphones with a ∅ 3.5 mm stereo mini plug to monitor
the recorded audio. Press the HEADPHONE +/- buttons to
adjust the volume.
NOTES
• You can also adjust the headphone volume with the
[¡ Audio Setup] > [Audio Output] > [Headphone
Volume] setting.
• When you are monitoring the audio, you can choose to
synchronize the audio signal with the video signal or
monitor the audio in real time. Use the [¡ Audio Setup]
> [Audio Output] > [Monitor Delay] setting to select the
method.
× (headphone)
terminal
Colors Bars/Audio Reference Signal
Colors Bars/Audio Reference Signal
You can have the camcorder generate and record color bars and a 1 kHz audio reference signal and output
them from the 3G/HD-SDI terminal1, MON. terminal1, HDMI OUT terminal, AV OUT terminal and × (headphone)
terminal2.
1
2
107
only.
Outputs audio reference signal only.
English
Operating modes:
Recording Color Bars
You can choose between SMPTE standard-definition color bars and ARIB
multi-format HDTV color bars.
1 Open the color bars [Type] submenu.
[~ Camera Setup] > [Color Bars] > [Type]
[~ Camera Setup]
[Color Bars]
[Type]
2 Select the type of color bars and then press SET.
Y
P
O
3 Open the [Enable] submenu to activate the color bars.
[SMPTE]
[~ Camera Setup] > [Color Bars] > [Enable]
4 Select [On] and then press SET.
• The selected color bars appear on the screen and will be recorded
when you press the START/STOP button.
• Turning the camcorder off or changing the operating mode to
mode will deactivate the color bars.
C
[~ Camera Setup]
[Color Bars]
[Enable]
NOTES
[Off]
• When you want to display the color bars, set the custom picture file to
[Off] (A 132) or set the [Other Functions] > [Over 100%] setting in the
custom picture file to [Through] (A 140).
• If you set an assignable button to [Color Bars] (A 129), you can press the button turn the color bars on/off.
Recording an Audio Reference Signal
The camcorder can output a 1 kHz audio reference signal with the color
bars.
[¡ Audio Setup]
[Audio Input]
1 Open the [1 kHz Tone] submenu.
[¡ Audio Setup] > [Audio Input] > [1 kHz Tone]
2 Select the desired level and then press SET.
[1 kHz Tone]
[Off]
• Available levels are -12 dB, -18 dB and -20 dB.
• Select [Off] to turn off the signal.
• The signal is output at the selected level and will be recorded when you press the START/STOP button.
Video Scopes
Video Scopes
108
The camcorder can display a simplified waveform monitor or vectorscope. It can also display an edge monitor*
to help you focus. The video scopes appear only on the OLED screen. They do not appear in the viewfinder or
on an external monitor.
* The edge monitor looks at the focus of the entire picture and displays the results as a waveform. The edge monitor is available
only in
mode.
Displaying a Video Scope
Operating modes:
Press the WFM button.
• The waveform monitor will appear in a window on the lower
right of the screen.
• You can repeatedly press the WFM button to activate the
video scopes in the following sequence.
Waveform monitor Vectorscope Edge monitor Off
• Alternatively, you can display the video scopes using
[w Other Functions] > [WFM (OLED)] > [Setting]. Select
[WFM] for the waveform monitor, [VS] for the vectorscope or
[Edge Mon.] for the edge monitor.
C
Configuring the Waveform Monitor
Y
P
O
The camcorder’s waveform monitor function offers 5 modes. You can also
change the gain.
[w Other Functions]
[WFM (OLED)]
Operating modes:
[Waveform Monitor]
1 Open the waveform monitor [Type] submenu.
[w Other Functions] > [WFM (OLED)] > [Waveform Monitor] >
[Type]
2 Select the desired option and then press SET.
[Type]
[Line]
• If you do not need to change the gain, you do not need to perform
steps 3 and 4.
3 Open the waveform monitor [Gain] submenu.
[w Other Functions] > [WFM (OLED)] > [Waveform Monitor] > [Gain]
4 Select [1x] or [2x] and then press SET.
Options
[Line]:
[Line+Spot]:
[Field]:
[RGB]:
[YPbPr]:
Sets the waveform monitor to line display mode.
The waveform of the area in the red frame is displayed in red on top of the [Line] mode waveform.
Sets the waveform monitor to field display mode.
Functions like an RGB parade scope.
Functions like a YPbPr parade scope.
Video Scopes
Configuring the Vectorscope
The camcorder’s vectorscope function offers 2 modes. You can also
change the gain.
[w Other Functions]
[WFM (OLED)]
Operating modes:
109
[Vectorscope]
[w Other Functions] > [WFM (OLED)] > [Vectorscope] > [Type]
2 Select the desired option and then press SET.
• If you do not need to change the gain, you do not need to perform
steps 3 and 4.
[Type]
[Normal]
3 Open the vectorscope [Gain] submenu.
[w Other Functions] > [WFM (OLED)] > [Vectorscope] > [Gain]
4 Select [1x] or [5x] and then press SET.
Options
[Spot]:
[Normal]:
The color signal of the area in the red frame is displayed in red on top of the [Normal] mode waveform.
Displays the vectorscope.
Configuring the Edge Monitor
Y
P
O
Using this video scope allows you to focus with more precision. You can
use the edge monitor along with the other focus assistance functions
(A 84). The edge monitor features 2 modes.
Operating modes:
C
1 Open the edge monitor [Type] submenu.
[w Other Functions] > [WFM (OLED)] > [Edge Monitor] > [Type]
2 Select the desired option and then press SET.
[w Other Functions]
[WFM (OLED)]
[Edge Monitor]
[Type]
[Type 1]
• If you do not need to change the gain, you do not need to perform
steps 3 and 4.
3 Open the edge monitor [Gain] submenu.
[w Other Functions] > [WFM (OLED)] > [Edge Monitor] > [Gain]
4 Select the desired gain value and then press SET.
Options
[Type 1]:
[Type 2]:
The waveform that represents the focus of the entire picture is displayed in green. In addition, the
waveform of the area in the three red frames is displayed in red on top of the previous waveform.
This mode displays the edge monitor with the waveform monitor in [Line+Spot] mode. The waveform
monitor appears on the left in green while the edge monitor appears on the right in blue. The waveform of
the area in the red frame is displayed in red on top of the edge monitor waveform.
English
1 Open the vectorscope [Type] submenu.
Adding Marks to MXF Clips while Recording
Adding Marks to MXF Clips while Recording
110
When recording MXF clips, you can flag an important shot in a clip by adding a “shot mark” (!). There are two
types of shot marks, shot mark 1 (") and shot mark 2 (#), and you can add either or both types to a single MXF
clip. You can also add an OK mark ($) or check mark (%) to the entire clip to flag clips you want to set apart.
When the camcorder is in
mode, you can add or delete shot marks (A 157). You can also display an
index screen of all the shot marks (A 155), allowing you to find a particular scene in a clip more quickly.
Operating modes:
Adding Shot Marks while Recording
To add a shot mark to a clip while recording, you must first set in advance an assignable button to [Add Shot
Mark 1] or [Add Shot Mark 2].
1 Set an assignable button to [Add Shot Mark 1] or [Add Shot Mark 2] (A 129).
• To add both shot marks, set one assignable button to [Add Shot Mark 1] and another assignable button to
[Add Shot Mark 2].
Y
P
O
2 While you are recording, press the assignable button at the beginning of the shot you wish to mark.
• A message indicating the shot mark will appear and the selected shot mark will be added to the current
frame of the clip.
•
•
•
•
NOTES
Up to 100 shot marks (" and # marks combined) can be added to a single MXF clip.
There may be up to a 0.5 second delay from when you press the button to when the camcorder adds the shot
mark.
When you are using interval recording or frame recording mode, you cannot add shot marks to a clip.
When an MXF clip contains either shot mark, ! will appear next to the clip’s thumbnail in the playback index
screen.
C
Adding an $ Mark or % Mark to the Last Clip Recorded
After recording an important MXF clip, you can add an OK mark ($) or check mark (%) to the clip to flag it and
set it apart. When the camcorder is in
mode, you can display an index screen that contains only clips with
an $ mark or only clips with a % mark (A 146). Furthermore, you can use the $ mark to protect important
clips, as MXF clips with an $ mark cannot be deleted.
To add an $ mark or % mark to the last clip recorded in
mode, you must first set in advance an
assignable button to [Add $ Mark] or [Add % Mark].
1 Set an assignable button to [Add $ Mark] or [Add % Mark] (A 129).
• To add both types of clip marks (to different clips), set one assignable button to [Add $ Mark] and another
assignable button to [Add % Mark].
2 After recording a clip, press the assignable button.
• A message indicating the clip mark will appear and the selected clip mark will be added to the clip.
NOTES
• A clip cannot have both an $ mark and a % mark at the same time.
Using Metadata
Using Metadata
The camcorder automatically adds metadata to MXF clips while they are being recorded. You can use Canon XF
Utility to check and search for specific metadata. You can also create and transfer a user memo remotely using
the Browser Remote application (A 182).
Entering content
Metadata
Canon XF Utility
Browser Remote
Canon XF Utility
–
Ü1
Ü
Ü
Ü2
Ü3
Ü
Ü
–4
–
–
Ü
Ü
(A 208)
–
–
–
User Memo: clip title, creator, location and description.
GPS information: altitude, latitude and longitude.
Recording data: Shutter speed, gain value, etc.
Unique Material Identifiers (UMID): country, organization
and user codes based on the SMPTE standard.
Checking content
Camcorder
1
2
User memo files need to be created using the software and saved on the SD card in advance.
Only when an optional GP-E2 GPS Receiver is connected to the camcorder. While recording, GPS information is recorded
automatically by the camcorder (A 114).
3 GPS information can only be added to clips already recorded.
4 Recording data is logged automatically by the camcorder.
Operating modes:
Y
P
O
Setting a User Memo Created with Canon XF Utility
Before you can add a user memo, you must first install Canon XF Utility (A 168). Next, create the user memo
and save it to an SD card. Once you insert the SD card in the camcorder and select the user memo, it will be
added to MXF clips you record.
For details on using the software, refer to the instruction manual that is installed with Canon XF Utility (A 170).
C
1 Use Canon XF Utility to save a user memo to an SD card.
• For details, refer to Managing User Memo Profiles in the Canon XF Utility Instruction Manual.
2 Insert the SD card into the SD card slot of the camcorder.
3 Open the metadata [Setting] submenu.
[w Other Functions] > [MXF] > [Set Metadata] > [Setting]
4 Select [SD Card] and then press SET.
[w Other Functions]
[MXF]
5 Open the [User Memo] submenu.
[w Other Functions] > [MXF] > [Set Metadata] > [User Memo]
[Set Metadata]
6 Select the file name of the desired user memo and then press SET.
• The Q icon appears on the right of the screen.
• Select [Off] to record clips without a user memo.
[Setting]
[SD Card]
English
Metadata components
111
Using Metadata
112
NOTES
• After you set a user memo, do not remove the SD card while you are
recording. If the SD card is removed, the user memo will not be added
to MXF clips.
• You must set the user memo before you start recording for it to be added to
MXF clips. You cannot change the user memo already added to an MXF clip
using the camcorder but you can do so with Canon XF Utility.
[w Other Functions]
[MXF]
[Set Metadata]
[User Memo]
Setting a User Memo Using Browser Remote
After completing the necessary preparations (A 182), you can create a user memo profile and transfer it to the
camcorder from a connected device using the Browser Remote application. Using the Browser Remote
application you have two additional advantages over user memos created with Canon XF Utility: you can
change the user memo of the last clip recorded, even if you did not specify a user memo in advance; and you
can enter manually the GPS information of your shooting location as long as the optional GP-E2 GPS receiver is
not connected to the camcorder.
1 Press the [Metadata Input] tab on the Browser Remote screen.
2 Press [
Activate].
Y
P
O
• Alternatively, on the camcorder, you can set [w Other Functions] > [MXF] > [Set Metadata] > [Setting] to
[Remote].
3 Fill the necessary user memo and GPS information fields.
• You can press [Clear] to clear the information entered into each field.
C
4 Press one of the transfer options to transfer the metadata to the camcorder.
• [Metadata correctly transferred] will be displayed on the Browser Remote screen and the metadata will be
transferred and applied to the clips on the camcorder.
5 Press ^ to close the message.
Options
[Apply from Next]: Adds the metadata you set in Browser Remote to all MXF clips recorded after the transfer.
[Overwrite Prev.]: Only available after recording an MXF clip. Adds the metadata you set in Browser Remote to all MXF
clips recorded after the transfer and also to the last MXF clip recorded (overwriting any user memo that
may have been recorded previously with the clip).
[Overwrite]: Only available while recording an MXF clip. Adds the metadata you set in Browser Remote to the MXF
clip that is being recorded (overwriting any previous user memo). It will also add this metadata to all MXF
clips recorded after the transfer.
Using Metadata
113
English
NOTES
• The metadata sent to the camcorder from Browser Remote will be lost in the following cases.
- If the camcorder was turned off.
- If the [w Other Functions] > [MXF] > [Set Metadata] > [Setting] setting was changed.
• Using Browser Remote ([
Activate] button) you can give priority to metadata sent through the application.
However, you cannot return the priority back to the SD card. To use a user memo file saved on the SD card
you will need to set [w Other Functions] > [MXF] > [Set Metadata] > [Setting] to [SD Card] on the
camcorder itself.
• Metadata sent to the camcorder from Browser Remote will not be added to relay clips recorded before the
switch to the current CF card.
C
Y
P
O
Recording GPS Information (Geotagging)
Recording GPS Information (Geotagging)
114
When the optional GP-E2 GPS Receiver is connected to the camcorder’s USB terminal, the camcorder will
automatically record the GPS information (longitude, latitude and altitude) to every recording you make (MXF
clips, MP4 clips and photos). For MP4 clips and photos, the UTC (coordinated universal time) date and time will
be recorded as well. For MXF clips, the GPS information is recorded as part of the clip's metadata and can be
used to organize and search recordings using Canon XF Utility (A 168).
In
mode, you can check whether a recording contains GPS information or not (A 145, 151).
Connecting the GPS Receiver
Turn off the camcorder and the receiver. Connect the receiver to the camcorder's USB terminal using the USB
cable*. While recording, place the receiver in the carrying case* and attach it to the camcorder's grip belt or carry
it on your person. For details about connecting and using the receiver, refer to the GP-E2 Instruction Manual.
* Supplied with the optional GP-E2 GPS Receiver.
Activating the GPS Receiver
C
Y
P
O
Operating modes:
Turn on the camcorder and receiver.
• The
icon appears on the right of the screen and will blink as the receiver tries to acquire satellite signals.
• When satellite signals are correctly acquired, the
icon will stay continuously on. GPS functions will be
activated and clips and photos recorded thereafter will be geotagged.
Adjusting the Date/Time Automatically According to GPS Position
Setting [w Other Functions] > [GPS Auto Time] to [On], you can have the camcorder automatically adjust its
date and time settings according to the information received from the GPS signal while an optional GP-E2
GPS Receiver is connected to the camcorder.
• When [w Other Functions] > [GPS Auto Time] is set to [On], [w Other Functions] > [Time Zone] and
settings in the [w Other Functions] > [Set Clock] submenu will not be available.
• While the Browser Remote application is in use, the automatic adjustment of the date/time will be
deactivated.
Recording GPS Information (Geotagging)
•
•
•
•
NOTES
On the [GPS Information Display] status screen (A 217), you can check the current GPS information and
satellite signal strength.
GPS signal reception may take some time after replacing the battery pack or when first turning on the
camcorder after a long period without use.
The camcorder is not compatible with the GPS receiver’s digital compass and positioning interval functions.
Also, the [Set now] option is not available for the [w Other Functions] > [GPS Auto Time] setting.
GPS information will not be recorded with photos captured from a clip.
C
Y
P
O
115
English
IMPORTANT
• In certain countries/regions, the use of GPS may be restricted. Be sure to use the GPS receiver in accordance
with local laws and regulations of the country/region where the receiver is used. Be particularly careful when
traveling outside of your home country.
• Be careful about using the GPS receiver in places where the use of electronic devices is restricted.
• The GPS information recorded with clips and photos may contain data that can lead others to locate or
identify you. Be careful when sharing geotagged recordings with others or when uploading them to the Web.
• Do not leave the GPS receiver near strong electromagnetic fields such as near powerful magnets and motors.
Reviewing a Recording
Reviewing a Recording
When the camcorder is in
was recorded.
mode, you can review the last clip that
[w Other Functions]
116
Operating modes:
[Review Recording]
1 Open the [Review Recording] submenu to set the review length.
[Entire Clip]
[w Other Functions] > [Review Recording]
2 Select the desired option and then press SET.
3 After you finish recording, press the u button.
• The last clip that was recorded is played back without
audio for the selected duration. [Ð REVIEW] appears at
the top of the screen.
• Press the CANCEL button to stop reviewing the clip and
change the camcorder back to record pause mode.
• After the clip finishes playing back, the camcorder returns
to record pause mode.
Y
P
O
Options
[Entire Clip]: Allows you to review the entire clip.
[Last 4 sec]: Allows you to review just the last 4 seconds of the
clip.
NOTES
• Clips cannot be reviewed when using a special recording mode (A 118) or when the movie format is set to
MXF+MP4 (A 55).
• If the camcorder switched CF cards during the recording of an MXF clip, the camcorder will play back the clip
on the CF card most recently recorded on.
C
File Numbering
File Numbering
MP4 clips and photos are automatically assigned consecutive numbers from 0001 to 9999, and stored on the
SD card in folders containing up to 500 recordings. Folders are numbered from 100 to 999 and the last 4 digits
of the folder name indicate the date when the folder was created. You can select the file numbering method to
be used. We recommend using the [Continuous] setting.
117
English
Operating modes:
1 Open the [File Numbering] submenu.
[w Other Functions]
[w Other Functions] > [File Numbering]
2 Select the desired option and the press SET.
Options
[Reset]:
File numbers will restart from 100-0001 every time you insert
a new SD card. If an SD card already contains previous
recordings, file numbers will continue from the number
following that of the last file on the SD card.
[Continuous]: File numbers will continue from the number following that of
the last MP4 clip or photo recorded with the camcorder.
Y
P
O
[File Numbering]
[Continuous]
NOTES
• The file number indicates the name and location of the file on the SD card. For example, an MP4 clip/photo
numbered 101-0107 that was recorded on 3 November, is located in the “DCIM\101-1103” folder as the file
“MVI_0107.MP4” or “IMG_0107.JPG”.
C
Special Recording Modes
Special Recording Modes
The camcorder features 4 special recording modes for recording MXF clips. Only pre-recording is available for
recording MP4 clips.
118
Interval recording: The camcorder will automatically record a pre-defined number of frames at a pre-defined
interval. This mode is suitable for recording subjects with little movement, such as natural surroundings or plants.
Frame recording: The camcorder will record a pre-defined number of frames every time you press the START/
STOP button. This mode is suitable for recording stop motion animation.
Slow & fast motion recording: This mode allows you to change the shooting frame rate to achieve a slow motion
or fast motion effect during playback.
Pre-recording: The camcorder will start recording approximately 3 seconds before you press the START/STOP
button. This is especially useful when it is difficult to predict when to start recording.
Interval Recording Mode
Set the interval and number of frames in advance. Sound is not recorded
in this special recording mode.
Operating modes:
Configuring Interval Recording Mode
Y
P
O
1 Open the [Interval] submenu.
[w Other Functions] > [Interval Recording] > [Interval]
C
[w Other Functions]
[Interval Recording]
[Interval]
[1 sec]
2 Select the desired interval and then press SET.
• See the following table for the available intervals.
3 Select [Recorded Frames], select the desired number of frames and
then press SET.
• Available options depend on the frame rate used: 1, 3, 6 or 9 (23.98P,
29.97P, 59.94i), or 2, 6 or 12 (59.94P).
Available intervals
[w Other Functions]
[Interval Recording]
[Recorded Frames]
1 sec
2 sec
3 sec
4 sec
5 sec
6 sec
7 sec
8 sec
9 sec
10 sec
15 sec
20 sec
30 sec
40 sec
50 sec
1 min
2 min
3 min
4 min
5 min
6 min
7 min
8 min
9 min
10 min
[1]
Activating Interval Recording Mode and Recording
[w Other Functions]
1 Open the [Special Recording] submenu.
[w Other Functions] > [Special Recording]
[Special Recording]
2 Select [Interval Recording] and then press SET.
• [INT STBY] appears at the top of the screen (with [INT] flashing).
[Off]
3 Press the START/STOP button to begin recording.
• The camcorder automatically records the set number of frames at the set interval.
• The front and rear tally lamps illuminate.
• [INT STBY] changes to [Ü INT REC] while recording frames and [Ü INT STBY] while between intervals.
4 Press the START/STOP button again to stop recording.
• All of the recorded frames are joined together into one clip.
Special Recording Modes
• The front and rear tally lamps go out and [INT STBY] appears at the top of the screen (with [INT] flashing).
•
•
Frame Recording Mode
Y
P
O
Set the number of frames in advance. We recommend operating the camcorder remotely or stabilizing the
camcorder, for example, on a tripod. Sound is not recorded in this special recording mode.
Operating modes:
C
Configuring Frame Recording Mode
1 Open the [Recorded Frames] submenu.
[w Other Functions] > [Frame Recording] > [Recorded Frames]
2 Select the desired number of frames and then press SET.
• Available options depend on the frame rate used: 1, 3, 6 or 9 (23.98P,
29.97P, 59.94i), or 2, 6 or 12 (59.94P).
[w Other Functions]
[Frame Recording]
[Recorded Frames]
[1]
Activating Frame Recording Mode and Recording
1 Open the [Special Recording] submenu.
[w Other Functions] > [Special Recording]
2 Select [Frame Recording] and then press SET.
• [FRM STBY] appears at the top of the screen (with [FRM] flashing).
[w Other Functions]
[Special Recording]
[Off]
3 Press the START/STOP button to begin recording.
• The camcorder automatically records the set number of frames.
• The front and rear tally lamps illuminate.
• [FRM STBY] changes to [Ü FRM REC] while recording frames and [Ü FRM STBY] when frames are not
being recorded.
• Repeat until you finish recording.
4 Open the [Special Recording] submenu.
[w Other Functions] > [Special Recording]
5 Select [Off] and then press SET.
• Frame recording mode ends and all of the recorded frames are joined together into one clip.
• The tally lamps go out and [STBY] appears at the top of the screen.
119
English
•
•
•
•
NOTES
You can use only one special recording mode at a time.
The interval and the number of frames recorded cannot be changed while recording.
Some frames at the point the recording was stopped may be recorded and added to the end of the clip.
Interval recording mode will be deactivated if the special recording mode is changed or turned off. It will be
deactivated also if you change the movie format or video configuration.
During this special recording mode, the time code’s running mode (A 90) can be set to [Rec Run] or [Regen.]
and the time code advances by the number of frames recorded. If the time code’s running mode is set to [Free
Run] or the time code is input from an external source, the running mode will switch to [Rec Run] during
special recording mode. When the special recording mode is deactivated, the running mode will return to its
previous setting.
During special recording mode, the time code signal will not be output from the TIME CODE terminal,
3G/HD-SDI terminal or MON. terminal.
Special Recording Modes
120
NOTES
You can use only one special recording mode at a time.
The number of frames recorded cannot be changed while recording.
Some frames at the point the recording was stopped may be recorded and added to the end of the clip.
Frame recording mode will be deactivated if the special recording mode is changed or turned off. It will be
deactivated also if you change the movie format or video configuration.
• During this special recording mode, the time code’s running mode (A 90) can be set to [Rec Run] or [Regen.]
and the time code advances by the number of frames recorded. If the time code’s running mode is set to [Free
Run] or the time code is input from an external source, the running mode will switch to [Rec Run] during
special recording mode. When the special recording mode is deactivated, the running mode will return to its
previous setting.
•
During special recording mode, the time code signal will not be output from the TIME CODE terminal,
3G/HD-SDI terminal or MON. terminal.
•
•
•
•
Slow & Fast Motion Mode
When you set the frame rate to a progressive frame rate (A 55), the camcorder can record with a frame rate
(shooting frame rate) that is different from the playback frame rate. Recording a clip at a higher frame rate than
the [Frame Rate] setting will result in a slow motion effect during playback (up to 40% of the original speed).
Conversely, a lower frame rate will result in a fast motion effect (up to 5x the original speed). Sound is not
recorded in this special recording mode.
Operating modes:
C
Configuring Slow & Fast Motion Mode
Y
P
O
1 Open the [S&F Frame Rate] submenu.
[w Other Functions] > [Slow & Fast Motion] > [S&F Frame Rate]
2 Select the desired shooting frame rate and then press SET.
• Available shooting frame rates depend on the resolution used.
[w Other Functions]
[Slow & Fast Motion]
[S&F Frame Rate]
Available shooting frame rates (fps)
12
15
18
20
21
22
24
25
26
27
28
30
32*
34*
36*
40*
44*
48*
54*
60*
[30]
* Available only when the resolution is set to 1280x720.
Activating Slow & Fast Motion Mode and Recording
1 Open the [Special Recording] submenu.
[w Other Functions] > [Special Recording]
2 Select [Slow & Fast Motion] and then press SET.
• [S&F STBY] appears at the top of the screen.
• The selected shooting frame rate appears on the right of the screen
next to the frame rate setting (the playback frame rate).
[w Other Functions]
[Special Recording]
[Off]
Special Recording Modes
Shooting frame rate
121
English
Playback frame rate
3 Press the START/STOP button to begin recording.
• The front and rear tally lamps illuminate.
• [S&F STBY] changes to [ÜS&F REC] while recording.
4 Press the START/STOP button again to stop recording.
• The clip is recorded at the selected frame rate.
• The tally lamps go out and [S&F STBY] appears at the top of the screen.
NOTES
• Slow & fast motion recording cannot be used together with other special recording modes or double slot
recording.
• The shooting frame rate cannot be changed while recording.
• For lower shooting frame rates, it may take approximately 1 second to stop recording.
• Slow & fast motion mode will be deactivated if the special recording mode is changed or turned off. It will be
deactivated also if you change the movie format or video configuration.
• When the bit rate is set to 50 Mbps (A 55), relay recording is not available during slow motion recording.
• During this special recording mode, the time code’s running mode (A 90) can be set to [Rec Run] or [Regen.]
and the time code advances by the number of frames recorded. If the time code’s running mode is set to [Free
Run] or the time code is input from an external source, the running mode will switch to [Rec Run] during
special recording mode. When the special recording mode is deactivated, the running mode will return to its
previous setting.
•
During special recording mode, the time code signal will not be output from the TIME CODE terminal,
3G/HD-SDI terminal or MON. terminal.
C
Y
P
O
Pre-recording Mode
When pre-recording mode is activated, the camcorder starts recording
continuously into a temporary memory of approximately 3 seconds so
when you press the START/STOP button, the clip will contain also
approximately 3 seconds of video and audio recorded before you pressed
the button.
Operating modes:
1 Open the [Special Recording] submenu.
[w Other Functions] > [Special Recording]
2 Select [Pre-Recording] and then press SET.
• [PRE REC STBY] appears at the top of the screen.
3 Press the START/STOP button to begin recording.
• The front and rear tally lamps illuminate.
• [PRE REC STBY] changes to [Ü PRE REC] while recording.
[w Other Functions]
[Special Recording]
[Off]
Special Recording Modes
4 Press the START/STOP button again to stop recording.
122
• The camcorder records the clip, including approximately 3 seconds of video and audio recorded before the
START/STOP button was pressed.
• The tally lamps go out and [PRE REC STBY] appears at the top of the screen.
NOTES
• During pre-recording mode, the time code will be recorded with the running mode (A 90) set to [Free Run],
regardless of the previous setting. Alternatively, you can use an external time code signal. When the time code
is recorded, it will include the 3 seconds before the START/STOP button was pressed. When the special
recording mode is deactivated, the running mode will return to its previous setting.
• You can use only one special recording mode at a time.
• Pre-recording mode will be deactivated if you change the movie format or video configuration.
C
Y
P
O
Simultaneous Recording of MXF and MP4 Clips
Simultaneous Recording of MXF and MP4 Clips
MXF+MP4 Simultaneous Recording: The camcorder will record the same scene in two different formats.
MP4 Backup Recording: The camcorder will keep recording continuously in MP4 format, ensuring that you never
miss important shooting opportunities. You can set the [Bit Rate/Resolution] setting of MP4 clips to [3 Mbps
640x360] or link it to the video configuration of the MXF clips.
Operating modes:
Video configurations of MXF clips and MP4 clips
MXF Clips
MP4 Clips
[Bit Rate/Resolution]1
Bit rate
[Bit Rate/Resolution]2 set to [Linked to MXF]
Frame rate
Bit rate
59.94i
35 Mbps
1920x1080
29.97P
23.98P
50 Mbps
59.94P
1280x720
29.97P
23.98P
59.94i
1920x1080
29.97P
23.98P
35 Mbps
1440x1080
59.94i
59.94P
1280x720
29.97P
23.98P
59.94i
25 Mbps
1440x1080
29.97P
23.98P
1
2
Y
P
O
Resolution
24 Mbps
Resolution
Frame rate
1920x1080
29.97P
C
23.98P
23.98P
59.94i
1920x1080
29.97P
23.98P
59.94i
17 Mbps
59.94P
1280x720
59.94i
1920x1080
29.97P
3 Mbps/
640x360
23.98P
29.97P
29.97P
23.98P
35 Mbps
24 Mbps
29.97P
29.97P
35 Mbps
9 Mbps
23.98P
59.94P
1280x720
Frame rate
29.97P
23.98P
35 Mbps
24 Mbps
Bit rate/
Resolution
59.94i
17 Mbps
9 Mbps
[Bit Rate/Resolution]2 set to
[3 Mbps 640x360]
29.97P
23.98P
[w Other Functions] > [MXF] > [Bit Rate/Resolution].
[w Other Functions] > [MP4] > [Bit Rate/Resolution] (when the movie format is set to MXF+MP4).
23.98P
29.97P
23.98P
123
English
Setting the movie format to MXF+MP4, you can record simultaneously clips in MXF format and clips in MP4
format. When the movie format is set to MXF+MP4, start and stop recording the MXF clip with the START/STOP
button, as usual. You can select whether that action would automatically record also an MP4 clip (MXF+MP4
simultaneous recording) or whether to assign a separate control to start and stop recording MP4 clips (MP4
backup recording).
Simultaneous Recording of MXF and MP4 Clips
1 Set the movie format to [MXF (CF)+MP4
] (A 55).
• At the top of the screen both [MP4] and [STBY] will appear. The time
code running mode will change to [Free Run] and start advancing.
124
2 Open the MP4 [Bit Rate/resolution] submenu.
[w Other Functions]
[MP4]
[w Other Functions] > [MP4] > [Bit Rate/Resolution]
3 Select [3 Mbps 640x360] or [Linked to MXF] and then press SET.
• Refer to the previous table to check the resulting video configuration
for MP4 clips.
[Bit Rate/Resolution]
[Linked to MXF]
4 Open the MP4 [Rec Control] submenu.
[w Other Functions] > [MP4] > [Rec Control]
[w Other Functions]
5 Select the desired option and then press SET.
[MP4]
[Rec Control]
[START/STOP Button]
Options
Y
P
O
[START/STOP Button]: Every time you press the START/STOP button, the camcorder will start or stop recording
simultaneously an MXF clip on the CF card and an MP4 clip on the SD card. Use this setting for
MXF+MP4 simultaneous recording.
[Assignable Buttons]: You can start or stop recording the MP4 clip using the menu ([w Other Functions] > [MP4] >
[Start/Stop] > [Start] or [Stop]) or an assignable button set to the [MP4 Start/Stop] function (A 129).
Use this setting for MP4 backup recording.
C
Recording in MP4 Backup Recording Mode
When [w Other Functions] > [MP4] > [Rec Control] is set to [Assignable Buttons] the actions that control the
recording of MXF clips and MP4 clips (the backup recording) are separate.
1 Open the MP4 [Start/Stop] menu.
[w Other Functions] > [MP4] > [Start/Stop]
2 Select [Start] and then press SET to start recording the backup
MP4 clip.
• The front and rear tally lamps will illuminate, [MP4] changes to
[ÜMP4] and the recording of the MP4 clip will begin.
• You can also set an assignable button to [MP4 Start/Stop] and press
the assignable button.
[w Other Functions]
[MP4]
[Start/Stop]
[Stop]
3 Press the START/STOP button to record an MXF clip
simultaneously with the MP4 clip.
• [STBY] changes to [ÜREC] and the recording of the MXF clip will begin.
4 Press the START/STOP button again to stop recording the MXF clip.
• [ÜREC] changes to [STBY] and the MXF clip is recorded on the CF card.
• Repeat steps 3 and 4 as necessary to record additional MXF clips. All along, the recording of the backup
MP4 clip will continue.
5 To stop recording the MP4 clip, open the MP4 [Start/Stop] menu.
• [w Other Functions] > [MP4] > [Start/Stop]
Simultaneous Recording of MXF and MP4 Clips
6 Select [Stop] and then press SET.
• The front and rear tally lamps will go out, [ÜMP4] will change back to [MP4] and the MP4 clip is recorded
on the SD card.
• You can also set an assignable button to [MP4 Start/Stop] and press the assignable button.
C
Y
P
O
English
NOTES
• If any memory card becomes full during MXF+MP4 simultaneous recording, recording will stop on all recording
media. If a memory card becomes full during MP4 backup recording, recording will stop only on the memory
card that is full and continue on other recording media.
• Simultaneous recording cannot be used together with other special recording modes or real-time proxy
transfer mode.
• While recording, the [Free Run] time code will be recorded with the MXF clip.
125
Infrared Recording
Infrared Recording
126
Using the infrared mode, the camcorder becomes more sensitive to infrared light, allowing you to record in dark
locations. You can use the camcorder’s own infrared light to keep shooting even in very dark conditions. Also,
you can select whether the brighter areas of the picture appear in green or white.
Operating modes:
Activating Infrared Mode
Follow the procedure below to set the camcorder to infrared
mode and to set the color of bright areas in the picture.
1 Move the INFRARED switch to ON.
• [Infrared] and the = icon will appear at the left of the
screen.
• The INFRARED switch will be more accessible when the
OLED panel is at a vertical position.
Y
P
O
2 Open the [Monochrome] submenu to select a color.
[~ Camera Setup] > [Infrared] > [Monochrome]
3 Select [White] or [Green] and then press SET.
C
Using the Infrared Light
You can turn the infrared light on and off using an assignable button or the
menu.
1 Open the [Light] submenu.
[~ Camera Setup] > [Infrared] > [Light]
2 Select the desired option and then press SET.
• When the infrared light is on, the < icon will appear on the left of the
screen.
Options
[Toggle]:
[~ Camera Setup]
[Infrared]
[Monochrome]
[White]
[~ Camera Setup]
[Infrared]
[Light]
[Toggle]
Allows you to turn the infrared light on and off using an assignable button. Set an assignable button
(A 129) to [Infrared Light] in advance and press the assignable button to turn the infrared light on/off.
[Always On]: The infrared light is always on while the camcorder is in infrared mode.
[Always Off]: The infrared light is always off.
Infrared Recording
C
Y
P
O
127
English
NOTES
• When the camcorder is in infrared mode, the following adjustments are made automatically.
- Gain, shutter speed and aperture are adjusted automatically and ND filters are not used.
- AGC limit, light metering, AE shift, white balance and custom picture settings cannot be used.
- The camcorder will switch from manual focus to autofocus so the focus point may change. Check that the
focus is correct.
• Depending on the light source, autofocus may not work well while zooming.
• When the camcorder is in infrared mode, do not point the lens at strong sources of light or heat. The
camcorder’s sensitivity to such sources is much higher than when shooting video normally. If there are such
sources in the picture before you switch the camcorder to infrared mode, shield the lens first.
• If you set an assignable button to [Infrared Monochrome] (A 129), you can press the button to change the
color of the bright areas of an infrared recording.
Using the Focal Length Guide
Using the Focal Length Guide
128
The focal length guide aids you when using two camcorders for 3D recording. The guide appears as a numerical
value and has a range of 202 steps. You can set the guide to 0 at any point in the zoom range to help precisely
calibrate both camcorders.
Operating modes:
1 Set up two camcorders and align their picture angle at full
telephoto.
[~ Camera Setup]
2 Open the [Focal Length] submenu.
[Zoom]
[~ Camera Setup] > [Zoom] > [Focal Length]
3 Select [Set To 0] and then press SET.
[Focal Length]
4 Press MENU.
• The focal length guide appears on the left of the screen as [
To turn off the indicator, select [Off] instead.
±0].
[Off]
5 Operate the zoom.
Y
P
O
• If both camcorders are set so that the same value is displayed during zoom, the focal length for both
camcorders will remain almost the same.
NOTES
• Although the focal length guide is an aid for 3D recording, make sure to check the picture angle visually while
recording.
• You can obtain more accurate results when you perform this procedure at full telephoto.
• The same picture angle for both camcorders cannot be guaranteed.
• When using the digital tele-converter or digital zoom
- When the focal length is reset to zero, the digital tele-converter or digital zoom is deactivated and
[~ Camera Setup] > [Zoom] > [Mode] is set to [Normal] (optical zoom only).
- If the focal length was reset to zero while the zoom was in the digital zoom range, the zoom position will
change automatically to the telephoto end of the optical zoom.
C
4
Customization
129
Assignable Buttons
* In
mode, only assignable buttons 1 to 4 and 11 to 13 are available.
Operating modes:
C
Y
P
O
Changing the Assigned Function
1 Open the [Assignable Buttons] submenu.
[w Other Functions] > [Assignable Buttons]
[w Other Functions]
[Assignable Buttons]
2 Select the button to change and then press SET.
• A list of available functions appears.
• The quick reference shows the default settings for each assignable
button. For assignable buttons 1 to 4 and 11 to 13, the label on the
camcorder/grip indicates also the button’s default setting. By default,
buttons 5 to 10 have no assignable function set.
3 Select the desired function and then press SET.
• If you selected [User Setting], the menu will change from orange to
blue to indicate you are selecting a menu setting to register. Continue
the procedure to register a menu setting. Otherwise, you do not need
to perform the rest of the procedure.
[1 PEAKING]
[2 ZEBRA]
[3 POWERED IS]
[4 MAGN.]
[5-10 (NONE)]
[11 HEADPHONE +]
[12 HEADPHONE -]
[13 WFM]
English
The camcorder conveniently features 13* buttons to which you can assign various functions. By assigning oftenused functions, you can quickly access them with a single press of a button.
Assignable Buttons
4 Navigate the menus to find the menu setting you want to register and then press SET.
• The selected menu setting will be assigned to the button marked with a ¥ to indicate that it is a userselected setting.
130
NOTES
• You can check the two [Assignable Buttons] status screens (A 210) to see what functions are set for the
assignable buttons.
• You can reset only the functions assigned to the assignable buttons, without affecting other camera settings,
with the [w Other Functions] >[Reset] > [Assignable Buttons] function. All the assignable buttons will return
to their default function.
Using an Assignable Button
After you assign a function to one of the assignable buttons, press the button to activate the function. For some
functions, an options menu may appear. In such case, select the desired option and then press SET.
Remote Operation Using Browser Remote
Y
P
O
After completing the necessary preparations (A 182), you can use the functions assigned to assignable
buttons 1 to 4 from a connected device using the Browser Remote application.
Press one of the assignable buttons 1 to 4 on the Browser Remote screen.
• You can check the functions assigned to these 4 assignable buttons on the Browser Remote screen.
Currently assigned functions
C
NOTES
• Even if [Shutter Increment] is assigned to one of the assignable buttons 1 to 4, it cannot be used from the
Browser Remote application.
Assignable Functions
Functions can be set separately in
functions and available modes.
mode and
Function name
mode. Refer to the following table for assignable
A
Description
[Img Stab.]
Turns image stabilization on/off.
Ü
–
87
[POWERED IS]*
Turns Powered IS on/off.
Ü
–
87
[Focus Limit]
Turns the focus limit on/off.
Ü
–
86
[Face AF]
Toggles the autofocus mode between [Face Priority], [Face Only] and [Off].
Ü
–
85
[Backlight]
Turns the [Backlight] light metering option on/off.
Ü
–
[Spotlight]
Turns the [Spotlight] light metering option on/off.
Ü
–
[Digital Zoom]
Turns the digital zoom on/off.
Ü
–
68
74
Assignable Buttons
Function name
A
Description
Ü
–
74
[Wide-End Angle]
Toggles the angle of view at wide-angle end between [Normal] and [Wider].
Ü
–
74
[Gain Mode]
Toggles the gain mode between [Automatic] and [Manual].
Ü
–
62
[Shutter Mode]
Toggles the shutter speed mode between [Automatic] and [Manual].
Ü
–
[Shutter Increment]
Changes the shutter speed increment between [Normal] and [Fine].
Ü
–
[WB Mode]
Toggles the white balance mode between automatic white balance (AWB) and
the current position of the WHITE BAL. switch.
Ü
–
69
[PEAKING]
Turns peaking on/off.
Ü
–
84
[ZEBRA]
Turns zebra patterns on/off.
Ü
–
89
[WFM]
Activates video scopes in the following sequence:
Waveform monitor J Vectorscope J Edge monitor (
Ü
Ü
108
[MAGN.]
Turns magnification on/off.
Ü
–
84
[TL-H58]
Sets the [~ Camera Setup] > [Conversion Lens] setting to [TL-H58] or [Off].
Ü
–
[WA-H58]
Sets the [~ Camera Setup] > [Conversion Lens] setting to [WA-H58] or [Off].
Ü
–
[Color Bars]
Turns color bars on/off.
Ü
–
107
[Infrared Monochrome]
Switches between white and green when the camcorder is in infrared mode.
Ü
–
126
[Infrared Light]
Turns the infrared light on/off when [~ Camera Setup] > [Infrared] >
[Light] is set to [Toggle].
Ü
–
126
[Markers]
Turns onscreen markers on/off.
Ü
–
88
[OLED Setup]
Opens the [OLED Setup] submenu.
Ü
Ü
34
[Viewfinder Setup]
Opens the [Viewfinder Setup] submenu.
Ü
Ü
34
[OLED/VF B&W]
Turns the B&W mode of the OLED screen and viewfinder on/off.
Ü
Ü
35
[Onscreen Display]
Turns on/off the inclusion of onscreen displays on video output from the
camcorder’s terminals (both HD and SD video output).
Ü
Ü
165
[MP4 Start/Stop]**
Starts or stops recording an MP4 clip.
Ü
–
123
[MP4 FTP Transfer]*
Adds the MP4 clip that was just recorded to the FTP transfer queue.
Ü
–
190
[Add Shot Mark 1]
Adds an " mark to the clip.
Ü
Ü
[Add Shot Mark 2]*
Adds an # mark to the clip.
Ü
Ü
[Add $ Mark]
Adds an $ mark to the clip.
Ü
Ü
[Add % Mark]
Adds a % mark to the clip.
Ü
Ü
[Time Code]
Displays the [Time Code] submenu.
Ü
–
90
[Time Code Hold]*
Puts the time code display on hold or resumes it.
Ü
Ü
91
[HEADPHONE +]
Increases the headphone volume.
Ü
Ü
[HEADPHONE -]
Reduces the headphone volume.
Ü
Ü
[Monitor Channels]
Switches the audio output channel.
Ü
Ü
166
105,
106
C
mode only) J Off
Y
P
O
58
80
110
152
149
[Audio Level]
Turns the audio level meter on/off.
Ü
Ü
[Wireless Controller]
Turns the supplied wireless controller on/off.
Ü
Ü
44
[Photo]*
Records a photo.
Ü
Ü
195
[Status]*
Displays the status screens.
Ü
Ü
209
[My Menu]
Opens the [My Menu] customized submenu.
Ü
–
30
[Initialize Media]
Opens the [Initialize Media] submenu.
Ü
Ü
41
[User Setting]*
Customizable slot. Assign to the button any menu setting you would like to
register.
Ü
Ü
–
* This function can be used only by assigning it to an assignable button.
** This function can only be assigned to assignable buttons 1 to 4.
131
English
[Tele-converter]
Activates the digital tele-converter in the following sequence:
1.5x J 3x J 6x J Off
Custom Picture Settings
Custom Picture Settings
132
You can preset a number of picture-related settings (A 135). After changing individual settings to your
preference, you can save the whole set in the camcorder or on an SD card as a custom picture file. You can then
load the file at a later date to change the current settings to the preset levels you selected. You can even add
custom picture settings to MXF clips recorded on a CF card.
You can save up to 9 different custom picture files on the camcorder and up to 20 custom picture files on an SD
card. Custom picture files can be copied between the camcorder and SD card.
Custom picture files created with this camcorder are compatible only with other XF200 / XF205 camcorders.
Operating modes:
Selecting Custom Picture Files
Select a custom picture file to easily apply its settings to your recordings
or to edit, rename, protect, or transfer it.
1 Open the [Custom Picture] submenu.
[~ Camera Setup] > [Custom Picture]
Y
P
O
2 Select [- / Select File] and then press SET.
• The default custom picture file is [Off]. A list of custom picture files in
the camcorder and SD card appears. Files in the camcorder begin
with [C1] to [C9]; those on the SD card begin with [SD1] to [SD20].
3 Select the desired file and then press SET.
C
[~ Camera Setup]
[Custom Picture]
[- / Select File]
[Off]
• Select [Off] to record without applying any custom picture settings.
• To apply the custom picture settings of the selected file, continue to step 4. To perform other operations on
the selected file (edit settings, copy, protect, etc.), continue instead with the one of the procedures in the
following pages.
4 Press the MENU button to exit the menu.
• The selected custom picture file’s settings will be applied. / (camcorder) or . (SD card) and the custom
picture file’s number will appear on the left of the screen.
Preset Custom Picture Files
By default, custom picture file [C9] in the camcorder is protected. Remove the protection (A 133) to edit the
file.
[C9: Wide DR]: Applies a gamma curve with a very wide dynamic range and an appropriate color matrix.
NOTES
• About changing custom picture related settings using the optional RC-V100 Remote Controller
- When the remote controller is connected to the camcorder, you can press the remote controller's CUSTOM
PICT. button to open/close the [Custom Picture] submenu.
- If a protected custom picture file or no custom picture file is selected on the camcorder ([- / Select File]
is set to [Off]), custom picture related settings cannot be changed using the remote controller.
- While the remote controller is connected to the camcorder, custom picture files on the SD card ([SD1] to
[SD20]) cannot be used. If you connect the remote controller while a custom picture file on the SD card was
selected, the custom picture file will change automatically to [Off] (recording without custom picture
settings). To use the settings of a custom picture file saved on the SD card, copy the file in advance from the
SD card to an open file slot in the camcorder (A 134).
Custom Picture Settings
- Adjusting custom picture related settings using the remote controller will change the settings registered
under the currently selected custom picture file. If you want to keep an important custom picture file, copy it
in advance to the SD card or select in advance a custom picture file you do not mind changing.
133
English
Editing a Custom Picture File’s Settings
1 After selecting a file, select [, / Edit File] and then press SET.
2 Select a setting and then press SET.
3 Change the setting to the desired level and then press SET.
• Refer to the table Available Custom Picture Settings (A 135) for details on the various settings.
• Repeat steps 2 and 3 for other settings, as necessary.
4 Press the MENU button to exit the menu.
• The new custom picture settings will be applied. / (camcorder) or . (SD card) and the custom picture
file’s number will appear on the left of the screen.
Resetting the current file’s settings to default values
1 Select [Reset] and then press SET.
Y
P
O
2 Select the default values and then press SET.
• Select [Normal] to reset to neutral default values (equivalent to not using custom picture settings at all) or
[Wide DR] if you want to replicate the preset settings, for example as a starting point to edit them further.
3 Select [OK] and then press SET.
C
Renaming Custom Picture Files
1 After selecting a file, open the [Rename] submenu.
[, / Edit File] > [Rename]
[, / Edit File]
[Rename]
• A screen appears that displays the current file name with an orange
selection frame on the first character.
2 Push the joystick up/down to select an alphanumeric character or symbol then push it right to move
to the next field.
• Change the rest of the name in the same way.
3 Select [Set] and then press SET.
4 Press the MENU button to exit the menu.
Protecting Custom Picture Files
Protecting a custom picture file prevents its settings from being
accidentally changed.
1 After selecting a file, open the [Protect] submenu.
[, / Edit File] > [Protect]
2 Select [Protect] and then press SET.
• In the custom picture menu, i will appear next to the file name.
• To remove protection settings, select [Unprotect] instead.
[, / Edit File]
[Protect]
Custom Picture Settings
3 Press the MENU button to exit the menu.
134 Transferring Custom Picture Files
You can transfer custom picture files between the camcorder and SD card. When the selected custom picture
file is in the camcorder, use [Copy To
] or [Load From
] depending on the operation you wish to perform.
Similarly, when the selected custom picture file is on an SD card, use [Copy To Cam.] or [Load From Cam].
Copying a File from the Camcorder to an SD Card
1 After selecting a file in the camcorder, open the [Copy To
[+ / Transfer File] > [Copy To
]
] submenu.
[+ / Transfer File]
[Copy To
2 Select the file slot on the SD card under which to save the file and then
press SET.
• If there are available slots, you can select [New File] to save the file in the first available slot.
]
3 Select [OK] and then press SET.
• The currently selected file will be copied to the selected slot on the SD card, overwriting the file in that slot.
When the confirmation screen appears, press SET.
4 Press the MENU button to exit the menu.
Y
P
O
Replacing a File in the Camcorder with a File on an SD Card
1 After selecting a file in the camcorder to replace, open the
[Load From
] submenu.
[+ / Transfer File] > [Load From
]
C
[+ / Transfer File]
[Load From
]
2 Select the file to transfer to the camcorder and then press SET.
3 Select [OK] and then press SET.
• The file in the camcorder will be overwritten by the one on the SD card. When the confirmation screen
appears, press SET.
4 Press the MENU button to exit the menu.
Copying a File from an SD Card to the Camcorder
1 After selecting a file on the SD card, open the [Copy To Cam.]
submenu.
[+ / Transfer File] > [Copy To Cam.]
[+ / Transfer File]
[Copy To Cam.]
2 Select the file slot under which to save the file and then press SET.
3 Select [OK] and then press SET.
• The currently selected file will be copied to the selected slot on the camcorder, overwriting the file in that
slot. When the confirmation screen appears, press SET.
4 Press the MENU button to exit the menu.
Replacing a File on an SD Card with a File in the Camcorder
1 After selecting a file on the SD card to replace, open the
[Load From Cam.] submenu.
[+ / Transfer File] > [Load From Cam.]
2 Select the file to transfer to the SD card and then press SET.
[+ / Transfer File]
[Load From Cam.]
Custom Picture Settings
3 Select [OK] and then press SET.
• The file on the SD card will be overwritten by the one on the camcorder. When the confirmation screen
appears, press SET.
4 Press the MENU button to exit the menu.
135
Embedding Custom Picture Settings in a Recording
By default, when you record MXF clips using custom picture settings, the
custom picture file is saved along with the MXF clip. Later, you can copy
the custom picture file embedded in the MXF clip to the camcorder
(A 155) and use the same custom picture settings to record additional
clips. You may find that embedding custom picture settings in a recording
helps you keep track of them, such as verifying what settings were used
for a particular recording.
1 Open the [Add / File] submenu.
Y
P
O
[w Other Functions] > [MXF] > [Clips] > [Add / File]
2 Select [On] or [Off] and then press SET.
C
Available Custom Picture Settings
[w Other Functions]
[MXF]
[Clips]
[Add / File]
[On]
The following are the available settings. Even if no custom picture file is selected, the default settings are still
applied to the picture.
[Gamma]
The gamma curve changes the overall look of the image. Generally, this should be the same setting as [Select]
under [Color Matrix]. (Default: [Normal 1]).
[Normal 1] to [Normal 4]: These settings are suitable for viewing the image on a TV monitor. Highlights in
[Normal 2] are brighter than those of [Normal 1]. Dark tones in the lower part of the gamma
curve for [Normal 3] (ITU-R BT.709 standard) and [Normal 4] are more pronounced than those of
[Normal 2].
[Cine 1] or [Cine 2]: Use [Cine 1] for a gamma curve that results in a picture with a cinema-like feel and cinemalike tones. [Cine 2] has softer contrasts than does [Cine 1] but is also suitable for creating a
cinema-like picture.
[Wide DR]:
Applies a gamma curve with a very wide dynamic range, optimized for playback on an HDTV.
English
NOTES
• You can also copy to the camcorder a custom picture file embedded in an MXF clip (A 155).
Custom Picture Settings
Gamma
Normal 1
Cine 1
Cine 2
Normal 2/3/4
Output
Output
136
Normal 1
Wide DR
Normal 4
Normal 3
Normal 1/2
Input
Input
[Black]
Controls the black level and color cast of blacks.
[Master Pedestal]: The master pedestal increases or decreases the black level. Higher settings will make dark
areas brighter but decrease contrast. This setting can be adjusted from -50 to 50. (Default: ±0)
[Master Black]: Corrects color cast in blacks.
[Red]:
-50 to 50 (Default: ±0)
[Green]: -50 to 50 (Default: ±0)
[Blue]: -50 to 50 (Default: ±0)
[Black Gamma]
Y
P
O
Controls the lower part of the gamma curve (dark areas of the image). When [Gamma] is set to [Wide DR], this
setting has no effect on the picture.
[Level]:
Raises or lowers the lower part of the gamma curve. This setting can be adjusted from -50 to
50. (Default: ±0)
[Range]:
Selects the range in which dark areas are affected. This setting can be adjusted from -20 to 50.
(Default: ±0)
[Point]:
Determines the shape of the lower part of the gamma curve. This setting can be adjusted from 20 to 50. (Default: ±0)
C
Output
Black Gamma
Point
Input
[Low Key Satur.]
Adjusts color saturation in dark areas.
[Enable]:
Activates/deactivates the setting. (Default: [Off])
[Level]:
Specifies how saturated colors are in dark areas. This setting can be adjusted from -50 to 50.
(Default: ±0)
Custom Picture Settings
[Knee]
Knee Slope
Knee Point
Output
Output
Input
[Sharpness]
Y
P
O
C
Input
Sets the sharpness of the output and recording signal.
[Level]:
Sets the sharpness level. This setting can be adjusted from -10 to 50. (Default: ±0)
[H Detail Freq.]: Sets the center frequency of horizontal sharpness. Setting higher values increases the
frequency, which, in turn, increases the sharpness. This setting can be adjusted from -8 to 8.
(Default: ±0)
[Coring]:
Reduces noise artifacts caused by high sharpness levels.
[Level]: Sets the coring level. Higher values prevent sharpness from being applied to minute details, resulting
in less noise. This setting can be adjusted from -30 to 50. (Default: ±0)
[D-Ofst]: You can use [D-Ofst], [D-Curve] and [D-Depth] to adjust the coring level based on brightness. [D-Ofst]
sets the coring level of the minimum brightness level. This setting can be adjusted from 0 to 50.
(Default: 0)
[D-Curve]: Sets the curve of the coring adjustment. This curve is the change from [Level] to [D-Ofst]. This setting
can be adjusted from 0 to 8. (Default: 0)
[D-Depth]: Sets a multiplier to [D-Ofst] that determines the coring level adjustment based on brightness.
Positive values raise the coring level in dark areas and negative values lower the level. This setting can
be adjusted from -4 to 4. (Default: ±0)
[HV Detail Bal.]: Adjusts the ratio between horizontal and vertical detail. Higher values emphasize vertical detail
while lower values emphasize horizontal detail. This setting can be adjusted from -8 to 8.
(Default: ±0)
[Limit]:
Restricts how much sharpness is applied. This setting can be adjusted from -50 to 50.
(Default: ±0)
137
English
Controls the upper part of the gamma curve (highlights of the image). By compressing the highlights, you can
prevent parts of the image from being overexposed. When [Gamma] is set to [Cine 1], [Cine 2] or [Wide DR], this
setting has no effect on the picture.
[Enable]:
Activates/deactivates the setting. (Default: [On])
[Automatic]:
Select [On] to have the camcorder automatically set the knee point and slope to prevent images
being overexposed so quickly. Select [Off] to manually adjust the knee point. (Default: [On])
[Slope]:
Determines the slope of the gamma curve above the knee point. This setting can be adjusted
from -35 to 50. (Default: ±0)
[Point]:
Sets the knee point of the gamma curve. This setting can be adjusted from 50 to 109.
(Default: 95)
[Saturation]:
Adjusts color saturation in highlights. This setting can be adjusted from -10 to 10. (Default: ±0)
Custom Picture Settings
138
[Knee Aperture]: Allows you to set the sharpness of only the areas above the knee point by adjusting the gain and
slope. When [Gamma] is set to [Cine 1], [Cine 2] or [Wide DR], this setting has no effect on the
picture.
[Gain]: Sets the amount of sharpness. This setting can be adjusted from 0 to 9. (Default: 0)
[Slope]: Sets the slope of the sharpness. This setting can be adjusted from 0 to 3, with 0 having no slope, 1
having a steep slope and 3 having a gradual slope. (Default: 1)
[Level Depend]: Lowers the amount of sharpness applied to dark areas of the image.
[Level]: Sets the brightness of the dark areas of the image that will be affected. This setting can be adjusted
from 0 to 50. (Default: 0)
[Slope]: Determines the slope of the area between the upper and lower parts of the gamma curve. This
setting can be adjusted from 0 to 3, with 0 having no slope, 1 having a steep slope and 3 having a
gradual slope. (Default: 0)
[Offset]: Adjusts the sharpness level of dark areas in the image. Setting higher values will lower the sharpness
level. This setting can be adjusted from 0 to 50. (Default: 0)
[Ingredient Ratio]: Changing this ratio allows you to affect the balance between resolution and the reduction of
jagged edges. Higher values emphasize resolution while lower values emphasize the reduction
of jagged edges. This setting can be adjusted from -50 to 50. (Default: 0)
[Noise Reduction]
Y
P
O
Reduces the amount of noise that appears in the image. Select [Automatic] to have the camcorder adjust the
noise automatically. Otherwise, select a level from 1 (lowest level) to 12 (highest level), or select [Off] to turn the
noise reduction off. (Default: [Off])
[Skin Detail]
The camcorder applies a softening filter to areas in the picture with skin tones to give a more pleasant
appearance. By changing these settings, you can determine what areas will be detected as skin tones. A zebra
pattern will appear over areas on the screen that are detected as having skin tones.
[Effect Level]: Adjusts the level of the filter. The available options are [Off], [Low], [Middle] and [High]. (Default:
[Off])
[Hue]:
Adjusts the hue for detection of skin tones. This setting can be adjusted from -16 to 16.
(Default: ±0)
[Chroma]:
Adjusts the color saturation for detection of skin tones. This setting can be adjusted from 0 to
31. (Default: 16)
[Area]:
Adjusts the color range for detection of skin tones. This setting can be adjusted from 0 to 31.
(Default: 16)
[Y Level]:
Adjusts the brightness for detection of skin tones. This setting can be adjusted from 0 to 31.
(Default: 16)
C
[Selective NR]
The camcorder detects the characteristics of a certain color or tone and applies a noise reduction filter to the
targeted areas. A zebra pattern will appear over targeted areas on the screen.
[Effect Level]: Adjusts the level of the noise reduction filter. The available options are [Off], [Low], [Middle] and
[High]. (Default: [Off])
[Hue]:
Adjusts the hue for the color to be detected. This setting can be adjusted from 0 to 31.
(Default: 0)
[Chroma]:
Adjusts the color saturation for the color to be detected. This setting can be adjusted from 0 to
31. (Default: 16)
[Area]:
Adjusts the color range for the color to be detected. This setting can be adjusted from 0 to 31.
(Default: 16)
[Y Level]:
Adjusts the brightness for the color to be detected. This setting can be adjusted from 0 to 31.
(Default: 16)
Custom Picture Settings
[Color Matrix]
[White Balance]
Y
P
O
Adjusts the amount of white balance throughout the whole image.
[R Gain]:
Adjust the intensity of red tones. This setting can be adjusted from -50 to 50. (Default: ±0)
[B Gain]:
Adjust the intensity of blue tones. This setting can be adjusted from -50 to 50. (Default: ±0)
[Color Correction]
C
The camcorder detects the characteristics of a certain color (color phase, chroma, area and Y level) and corrects
them when recording. You can set the color correction for up to two different areas (A and B).
[Select Area]: Selects the area or areas to correct. Available options are [Area A], [Area B] and [Area A&B].
Select [Off] to turn this setting off. (Default: [Off])
[Area A Setting]: Determines the area in which colors will be corrected.
[Phase]: Adjusts the color phase for area A. This setting can be adjusted from 0 to 31. (Default: 0)
[Chroma]: Adjusts the color saturation for area A. This setting can be adjusted from 0 to 31. (Default: 16)
[Area]: Adjusts the color range for area A. This setting can be adjusted from 0 to 31. (Default: 16)
[Y Level]: Adjusts the brightness for area A. This setting can be adjusted from 0 to 31. (Default: 16)
[Area A Revision]: Sets the amount of correction for area A.
[Level]: Adjusts the amount of correction to the color saturation. This setting can be adjusted from -50 to 50.
(Default: ±0)
[Phase]: Adjusts the amount of correction to the color phase. This setting can be adjusted from -18 to 18.
(Default: ±0)
[Area B Setting]: Determines the area in which colors will be corrected.
[Phase]: Adjusts the color phase for area B. This setting can be adjusted from 0 to 31. (Default: 0)
[Chroma]: Adjusts the color saturation for area B. This setting can be adjusted from 0 to 31. (Default: 16)
[Area]: Adjusts the color range for area B. This setting can be adjusted from 0 to 31. (Default: 16)
[Y Level]: Adjusts the brightness for area B. This setting can be adjusted from 0 to 31. (Default: 16)
[Area B Revision]: Sets the amount of correction for area B.
[Level]: Adjusts the amount of correction to the color saturation. This setting can be adjusted from -50 to 50.
(Default: ±0)
[Phase]: Adjusts the amount of correction to the color phase. This setting can be adjusted from -18 to 18.
(Default: ±0)
139
English
Color matrix affects the color tones throughout the whole image.
[Select]:
Available options are [Normal 1] to [Normal 4], [Cine 1] and [Cine 2] and [Wide DR]. Generally,
this should be the same setting as [Gamma]. After selecting an option, you can make more
precise adjustments. (Default: [Normal 1])
[Gain]:
Adjusts the color intensity. This setting can be adjusted from -50 to 50. (Default: ±0)
[Phase]:
Adjusts the color phase. This setting can be adjusted from -18 to 18. (Default: ±0)
[R-G]:
The R-G matrix changes the tint of the picture along the cyan/green and red/magenta
gradations. This setting can be adjusted from -50 to 50. (Default: ±0)
[R-B]:
The R-B matrix changes the tint of the picture along the cyan/blue and red/yellow gradations.
This setting can be adjusted from -50 to 50. (Default: ±0)
[G-R]:
The G-R matrix changes the tint of the picture along the magenta/red and green/cyan
gradations. This setting can be adjusted from -50 to 50. (Default: ±0)
[G-B]:
The G-B matrix changes the tint of the picture along the magenta/blue and green/yellow
gradations. This setting can be adjusted from -50 to 50. (Default: ±0)
[B-R]:
The B-R matrix changes the tint of the picture along the yellow/red and blue/cyan gradations.
This setting can be adjusted from -50 to 50. (Default: ±0)
[B-G]:
The B-G matrix changes the tint of the picture along the yellow/green and blue/magenta
gradations. This setting can be adjusted from -50 to 50. (Default: ±0)
Custom Picture Settings
[Other Functions]
[Setup Level]:
140
[Over 100%]:
Adjusts the black level set by the [Black] and [Master Pedestal] settings. This setting can be
adjusted from -50 to 50. (Default: ±0)
This function determines how the camcorder handles video signals exceeding 100%. Available
options are [Through] to do nothing, [Clip] to clip the signal at 100%, and [Press] that
compresses a signal of up to 108% down to 100% levels. (Default: [Through])
NOTES
• When an optional RC-V100 Remote Controller is connected to the camcorder, the following custom picture
settings can be changed using the buttons and dials on the remote controller. They cannot be changed from
the camcorder while the RC-V100 is connected.
- [Black] > [Master Pedestal]; [Black] > [Master Black] > [Red], [Blue]
- [Black Gamma] > [Level]
- [Knee] > [Slope] and [Point] (only when [Knee] > [Enable] is set to [On])
- [Sharpness] > [Level]
- [White Balance] > [R Gain], [B Gain]
C
Y
P
O
Customizing Functions and Onscreen Displays
Customizing Functions and Onscreen Displays
Operating modes:
Customizing Functions
The following table describes which functions can be customized using
[Custom Function].
[w Other Functions]
[Custom Function]
1 Open the [Custom Function] submenu.
[w Other Functions] > [Custom Function]
2 Select the desired function.
Y
P
O
3 Change the setting option and then press SET.
Customizable functions with [Custom Function]
Menu item
Description
[Shockless Gain]
Determines the speed of the transition when the gain is changed.
[Shockless WB]
Creates a softer transition when the white balance is changed.
[AE Response]
Controls the camcorder’s responsiveness for changing the aperture during automatic aperture mode.
[Iris Limit]
Sets a maximum aperture value (F8.0) to be used for shooting.
[Iris Ring Direction]
Changes the direction of the adjustment when turning the iris ring.
C
[Focus Ring Direction] Changes the direction of the adjustment when turning the focus ring.
[Zoom Ring Direction] Changes the direction of the adjustment when turning the zoom ring.
[Focus Ring Control]
Selects the sensitivity of the response when operating the focus ring.
[Zoom Ring Control]
Selects the sensitivity of the response when operating the zoom ring.
[Focus Assistance
B&W]
Automatically switches the screen to B&W while the focus assistance functions (peaking and magnification) are
activated. You can have the screen switch to B&W when only the peaking is activated, when only the magnification is
activated or when both are activated.
[Distance Units]
Selects the units of distance (meters or feet) displayed when the camcorder shows the distance to the subject in manual
focus mode.
[Zoom Indicator]
Selects the display of the zoom indicator between a graphic bar and a numeric display (0 to 99; 0 to 81 when
[~ Camera Setup] > [Conversion Lens] is set to [WA-H58]; 0 to 149 when digital zoom is activated).
[Scan Reverse Rec]
Inverts the recorded image horizontally and/or vertically.
[OSD Recording]
When this function is set to [On], all of the onscreen displays will be recorded to the MXF clip exactly as they appear on the
screen.
141
English
Customize the camcorder to match your shooting style and needs. Use the [w Other Functions] >
[Custom Function] settings to adjust how some of the camcorder’s controls and functions operate in
mode. Similarly, use the [£ OLED/VF Setup] > [Custom Display 1] or [Custom Display 2] settings to
customize the onscreen displays that appear during recording. You can save these preferences along with other
menu settings to an SD card and use them again later (A 143).
Customizing Functions and Onscreen Displays
Customizing Onscreen Displays
For details on which onscreen displays can be customized, refer to
Onscreen Displays (A 51).
142
1 Open the [Custom Display 1] or [Custom Display 2] submenu.
[£ OLED/VF Setup]
[Custom Display 1]
[Custom Display 2]
[£ OLED/VF Setup] > [Custom Display 1] or [Custom Display 2]
2 Select the desired onscreen display.
3 Change the setting option and then press SET.
• Most onscreen elements can be turned [On] or [Off]. A few elements, like the zoom display, will have the
option to be displayed all the time ([Always On]) or only while operated ([Normal]); others, like the remaining
battery or remaining recording time, will have the option to be displayed all the time ([Normal]) or only when
they are at a warning level ([Only warnings]).
C
Y
P
O
Saving and Loading Camera Settings
Saving and Loading Camera Settings
After you adjust custom picture settings and settings in the various menus, you can save those settings on an
SD card. You can load those settings at a later date or on another XF205 or XF200 camcorder so that you can
use that camcorder in that same exact way.
English
Operating modes:
Saving Camera Settings to an SD Card
1 Open the [Save To
[w Other Functions]
] submenu.
[w Other Functions] > [Transfer Menu//] > [Save To
]
[Transfer Menu//]
2 Select [Menu] or [Menu+/] and then press SET.
• Selecting [Menu] will save menu settings and [Menu+/] will save
menu and custom picture settings.
[Save To
]
3 Select [OK] and then press SET.
• The current settings are saved to the SD card. If the SD card already has camera settings on it, they will be
overwritten.
Y
P
O
4 When the confirmation screen appears, press SET.
Loading Camera Settings from an SD Card
1 Open the [Load From
143
C
] submenu.
[w Other Functions] > [Transfer Menu//] > [Load From
]
[w Other Functions]
[Transfer Menu//]
2 Select [Menu] or [Menu+/] and then press SET.
• Selecting [Menu] will load menu settings and [Menu+/] will load
menu and custom picture settings.
[Load From
]
3 Select [OK] and then press SET.
• After the camcorder’s current settings are replaced with the settings saved on the SD card, the screen will
turn black momentarily and the camcorder will restart.
NOTES
• The following settings are not saved on the SD card.
- Encryption keys/passwords under [w Other Functions] > [Network Settings] > [Connection Settings]
- Passwords under [w Other Functions] > [Network Settings] > [Remote Settings] > [Users Settings]
- [w Other Functions] > [Network Settings] > [FTP Server Settings] > [Password]
• When loading camera settings from an SD card, even protected custom picture files in the camcorder will be
replaced.
• Only camera settings from other XF200 / XF205 camcorders can be used with this camcorder.
Saving and Loading Camera Settings
144
C
Y
P
O
5
Playback
145
Playback
Operating modes:
MXF and MP4 Clip Index Screens
Playback functions are accessed from the index screen. To
open the MXF clip index screen or [MP4] index screen, set the
camcorder to
mode.
Y
P
O
Hold down the button on the Q switch and slide the
switch to MEDIA.
• The camcorder switches to
screen appears.
mode and the index
MXF clips
6
7
8
C
1
2
3
4
5
MP4 clips
9
10
11
12
13
14
15
16
17
18
19
English
This section explains how to play back clips with the camcorder. For details on playing back clips using an
external monitor, refer to Connecting to an External Monitor (A 162). For details on viewing photos on the SD
card, refer to Viewing Photos (A 197).
Playback
$ mark/% mark1 (A 110, 152)
Orange selection frame
Relay recording1 (A 148, see the explanation for
icon number 8)
4 Shot mark1 (A 110, 157)
5 MXF clip name1 (A 49)
6 Network type/FTP file transfer (A 173, 189)
7 Clip thumbnail (A 158)
8 Currently selected recording media (A 41)
9 Clip number / Total number of clips
10 Recording date (month and day only) and time1
1
2
3
146
1
2
3
11
12
13
14
15
16
17
18
19
Special recording mode1 (A 118)
Time code of thumbnail1
Total recording time
Recording date and time
Embedded custom picture file1 (A 132)
Bit rate and resolution (A 55)
Frame rate2 (A 55)
File number3 (A 117)
Clip geotagged with GPS information3 (A 111,
114)
MXF clips only.
For MXF clips recorded using slow & fast motion mode, the shooting frame rate and playback frame rate will both be displayed.
MP4 clips only.
Switching Between the CF Card Slots
If both CF card slots contain a CF card, you can switch between
them as necessary.
Operating modes:
Press the SLOT SELECT button.
Y
P
O
• The access indicator of the selected CF card slot will illuminate in
green.
C
Switching to Other Index Screens
All of the MXF clips on a CF card can be accessed from the MXF
clip index screen. However, you can switch to other index screens
that show only MXF clips with an $ mark ([$ Mark] index screen),
MXF clips with a % mark ([% Mark] index screen), MP4 clips*
([MP4] index screen) or photos* ([Photos] index screen).
* Photos and MP4 clips are saved on the SD card.
Operating modes:
1 Press the INDEX button.
• The index screen selection menu appears.
2 Select the desired index screen and then press SET.
• The selected index screen appears.
• Select [Cancel] instead to cancel the operation.
• Press the INDEX button again to return to the MXF clip index screen.
Playback
Playing Back Clips
You can play back clips from the MXF clip index screen,
[$ Mark] index screen, [% Mark] index screen and [MP4] index
screen. Use the playback control buttons on the camcorder or
use the joystick and joystick guide. You can also use the
supplied wireless controller.
147
English
1 In the index screen, move the orange selection frame to
the clip you want to play back.
2 Press the Ò button to start playback.
• Playback will start from the clip selected and continue until
the end of the last clip in the index screen. When the last
frame of the last clip is reached, playback will be paused.
• Press the Ò button again or press SET to pause/resume the playback.
• Press the Ñ button to stop the playback and return to the index screen.
IMPORTANT
• Observe the following precautions while any access indicators are illuminated or flashing in red. Failure to do
so may result in permanent data loss.
- Do not disconnect the power source or turn off the camcorder.
- Do not open the CF card slot cover or the SD card slot cover of the recording media being accessed and do
not remove the recording media.
Y
P
O
NOTES
• You may notice brief stops in video or audio playback between clips.
C
Onscreen Displays
MXF clips
7
8
9 10
MP4 clips
11
7
12
13
14
15
16
17
18
19
1
2
3
4
5
6
20
21
9
11
12
13
14
15
17
1
2
6
20
21
Playback
148
1
2
3
4
5
6
7
8
9
10
11
Remaining battery charge (A 51)
Joystick guide (A 148)
Shutter speed1 (A 58)
Aperture value1 (A 65)
Gain1 (A 62)
Recording date and time2
Playback operation
Relay recording3
Currently selected recording media (A 41)
$ mark/% mark3 (A 110, 152)
Time code (A 90)
12
13
14
15
16
17
18
19
20
21
Clip number / Total number of clips
Movie format (A 55)
Bit rate and resolution (A 55)
Frame rate4 (A 55)
Embedded custom picture file3 (A 135)
Output displays (A 165)
User bit3 (A 93)
4-channel audio3 (A 100)
Audio output channels (A 166)
Audio level meter
1
2
Appears for MXF clips only, when [£ OLED/VF Setup] > [Display Metadata] > [Camera Data] is set to [On].
Appears when [£ OLED/VF Setup] > [Display Metadata] > [Date/Time] is set to [On]. For MP4 clips, only the date of
recording appears.
3 MXF clips only.
4 For MXF clips recorded using slow & fast motion mode, the shooting frame rate and playback frame rate will both be displayed.
7 Playback operation
Ð PLAY
Ý PAUSE
Ô/Ó
F FWD ×
Ø F REV
Playback
Playback pause
Frame reverse/Frame advance
Fast playback*
Fast reverse playback*
Y
P
O
* The playback speed (x5, x15 or x60) will also appear in the indicator.
8 Relay recording
C
Appears when an MXF clip begins on one CF card and continues uninterrupted on the other. 5 indicates
the first part of the recording, 6 indicates the middle part(s) and 7 indicates the last part.
Playback Controls
When you play back a clip, operate the buttons on the
camcorder, the joystick and joystick guide or the supplied
wireless controller. Refer to the following table.
Playback
Available playback types
Playback type
Operation
Frame advance/reverse
Joystick: During playback pause, push the joystick up or down.
Wireless controller: Press the Ô or Ó button (during playback pause).
Skip to the beginning of the
next clip
Buttons: Press the Ù button.
Joystick: Push the joystick right.
Wireless controller: Press the ß button.
Skip to the beginning of the
current clip
Buttons: Press the Ú button.
Joystick: Push the joystick left.
Wireless controller: Press the à button.
Skip to the previous clip
Buttons: Press the Ú button twice.
Joystick: Push the joystick left twice.
Wireless controller: Press the à button twice.
Return to playback mode
Buttons: Press the Ò button.
Joystick: Press the joystick itself (SET button).
Wireless controller: Press the Ò button.
149
English
Fast playback
Buttons: Press the Ø or × button.
Joystick: During playback, push the joystick up or down.
Wireless controller: Press the Ø or × button.
Repeat to increase the playback speed to approximately 5x J 15x J 60x the normal speed.
Y
P
O
NOTES
• There is no audio during any of the playback types listed in the previous table.
• During some special playback modes, you may notice some anomalies (blocky video artifacts, banding, etc.)
in the playback picture.
• The speed indicated on the screen is approximate.
• During frame advance, the time advanced between frames depends on the video configuration used:
0.2 seconds (for 1280x720/59.94P MXF clips) or 0.5 seconds for other video configurations.
• You can press the DISP. button to turn the joystick guide display on and off.
C
Adjusting the Volume
During playback, audio will be output from the monaural
built-in speaker (on the grip) or from the stereo ×
(headphone) terminal. When you connect headphones to
the × (headphone) terminal, the built-in speaker will be
muted. The audio signal will also be output through the
3G/HD-SDI terminal*, MON. terminal*, HDMI OUT terminal
and AV OUT terminal.
*
only.
Press the HEADPHONE +/- buttons to adjust the
volume.
NOTES
• For details on changing the audio channel, refer to
Selecting the Audio Channel (A 166).
• You can also adjust the headphone or built-in speaker
volume with the [¡ Audio Setup] > [Audio Output] >
[Headphone Volume] or [Speaker Volume] setting.
× (headphone) terminal
Speaker
Clip Operations
Clip Operations
150
Besides playing back a clip, you can perform other operations such as deleting a clip or displaying an MXF clip’s
clip information. This is done through the clip menu, which contains different functions depending on the index
screen. You can use the functions in the [w Other Functions] menu to perform some of the operations on all the
clips or a selection of clips. Refer to the following table for available functions and refer to the following pages for
more details of the functions.
Operating modes:
MXF clip menu functions
Index screen
Menu item
[Display Clip Info]
Description
Displays various information about a clip.
MXF clips
[$ Mark]/
[% Mark]
[Shot Mark]1/
[Expand Clip]
A
Ü
Ü
–
151
–
[Add $ Mark]/
[Delete $ Mark]
Adds or deletes an $ mark.
Ü
Ü2
[Add % Mark]/
[Delete % Mark]
Adds or deletes a % mark.
Ü
Ü3
–
[Copy Clip]
Copies a clip from one CF card to the other.
Ü
Ü2
–
153
[Delete Clip]
Deletes a clip.
Ü
Ü3
–
154
[FTP Transfer]
Transfers the clip to a previously configured FTP server.
Ü
–
[Shot Mark]
Displays an index screen of all the frames of a clip that
have either shot mark.
Ü
Ü
–
[Shot Mark 1]
Displays an index screen of all the frames of a clip that
have the " mark.
Ü
Ü
–
[Shot Mark 2]
Displays an index screen of all the frames of a clip that
have the # mark.
Ü
Ü
–
[Expand Clip]
Displays an index screen that shows frames of a clip at
a fixed interval.
Ü
Ü
–
156
[Delete User Memo]
Deletes the user memo and GPS information of a clip.
Ü
Ü
–
155
[Copy / File]
Copies the custom picture file from a clip to the
camcorder.
Ü
Ü
–
155
[Add Shot Mark 1]/
[Del. Shot Mark 1]
Adds or deletes a " mark.
–
–
Ü
[Add Shot Mark 2]/
[Del. Shot Mark 2]
Adds or deletes a # mark.
–
–
Ü
[Fewer Index Pics]
Decreases the number of thumbnails that are displayed.
–
–
Ü4
[More Index Pics]
Increases the number of thumbnails that are displayed.
–
–
Ü4
[Pause]
Switches to playback of a clip with playback paused on
the selected frame.
–
–
Ü
–
[Set Index Picture]
Sets the thumbnail used in the MXF clip index screen.
–
–
Ü
158
1
2
3
4
152
C
Y
P
O
189
155
157
Includes also the [Shot Mark 1] and [Shot Mark 2] index screens.
[$ Mark] index screen only.
[% Mark] index screen only.
[Expand Clip] index screen only.
MP4 clip menu functions ([MP4] index screen)
Menu item
Description
A
[Delete]
Deletes a clip.
154
[FTP Transfer]
Transfers the clip to a previously configured FTP server.
191
156
Clip Operations
Using the Clip Menu
1 Select a clip and then press SET.
• The clip menu appears. Available functions depend on the index screen and which functions are enabled.
151
2 Select the desired function and then press SET.
IMPORTANT
• Observe the following precautions while any access indicators are illuminated or flashing in red. Failure to do
so may result in permanent data loss.
- Do not disconnect the power source or turn off the camcorder.
- Do not open the CF card slot cover or the SD card slot cover of the recording media being accessed and do
not remove the recording media.
Displaying Clip Information
Y
P
O
Select [Display Clip Info] in the clip menu to display the selected clip’s information screen ([Clip Info] screen).
Push the joystick left/right to switch to the previous/next clip. When you are finished, press the CANCEL button
to return to the MXF clip index screen.
Operating modes:
1
C
4 5 6 7
2
8
9
10
11
12
13
14
15
16
17
18
3
1
2
3
4
5
6
7
8
9
Thumbnail of the selected clip
Thumbnail of the previous clip
Thumbnail of the next clip
Shot mark (A 110, 157)
Clip geotagged with GPS information (A 111,
114)
Special recording mode (A 118)
Currently selected CF card slot (A 41)
Clip number / Total number of clips
Recording date and time
10
11
12
13
14
15
16
17
18
Clip name (A 49)
Bit rate and resolution (A 55)
Frame rate* (A 55)
$ mark / % mark (A 110, 152)
Embedded custom picture file (A 135)
Time code of the clip thumbnail
Time code of the first frame in clip
Time code of the last frame in clip
Clip duration
* For clips recorded using slow & fast motion mode, the shooting frame rate and playback frame rate will both be displayed.
English
• The function is enabled. For some functions, further action may be required. Follow the onscreen directions.
• Press the CANCEL button instead to return to the previous index screen.
Clip Operations
Displaying the User Memo
From the [Clip Info] screen, push the joystick up to display the [Q] screen. In this screen you can check details
about the embedded user memo. Push the joystick down to return to the [Clip Info] screen.
152
Displaying Custom Picture Settings
When displaying the [Clip Info] screen of a clip that has a custom picture file recorded with it, push the joystick
down to display the first of three screens with the clip’s custom picture settings ([/ Data 1/3] screen).
Repeatedly push down the joystick to check the information screens in the following order: [/ Data 2/3] screen
J [/ Data 3/3] screen J [Q] screen J [Clip Info].
Adding $ Marks or % Marks
If you add an OK mark ($) or check mark (%) to MXF clips, you can later display an index screen that shows
only the clips with an $ mark or only the clips with a % mark. Furthermore, you cannot delete clips with an $
mark so you can use this mark to protect important clips.
Operating modes:
Y
P
O
Adding an $ Mark or % Mark during Playback
To add an OK mark ($) or check mark (%) to a clip during playback or playback pause, you must first set an
assignable button to [Add $ Mark] or [Add % Mark] in advance.
1 Set an assignable button to [Add $ Mark] or [Add % Mark] (A 129).
• To add both types of clip marks (to different clips), set one assignable button to [Add $ Mark] and another
assignable button to [Add % Mark].
C
2 During playback or playback pause, press the assignable button to add the clip mark.
• A message indicating the clip mark will appear and the selected clip mark will be added to the clip.
• Adding a clip mark to a clip during playback will pause the playback.
Adding an $ Mark or % Mark from the Index Screen
1 Select the desired clip and then press SET to open the clip menu.
2 Select [Add $ Mark] or [Add % Mark] and then press SET.
• The clip information screen appears and it prompts you to confirm the operation.
3 Select [OK] and then press SET.
• The screen changes back to the MXF clip index screen and an $ mark or % appears next to the selected
clip’s thumbnail.
• Select [Cancel] instead to cancel the operation.
NOTES
• If you set an assignable button to [Add $ Mark] or [Add % Mark] (A 129), you can add an $ mark or %
mark to MXF clips from the index screen, during playback or during playback pause.
• A clip cannot have both an $ mark and % mark at the same time. When you add a % mark to a clip with an
$ mark, the $ mark will be deleted. Similarly, when you add an $ mark to a clip with a % mark, the %
mark will be deleted.
Clip Operations
Deleting $ Marks or % Marks
Operating modes:
153
Deleting an $ Mark or % Mark from a Clip
English
1 Select the desired clip and then press SET to open the clip menu.
2 Select [Delete $ Mark] or [Delete % Mark] and then press SET.
• The clip information screen appears and it prompts you to confirm the operation.
3 Select [OK] and then press SET.
• The screen changes back to the MXF clip index screen the selected mark is deleted.
• Select [Cancel] instead to cancel the operation.
Deleting $ Marks from All Clips
[w Other Functions]
1 Open the [Delete All $ Marks] submenu.
[w Other Functions] > [Delete All $ Marks]
2 Select [OK] and then press SET.
• All $ marks from clips on the selected CF card will be deleted.
• Select [Cancel] instead to cancel the operation.
• While the $ marks are being deleted, you can press SET to cancel.
[Delete All $ Marks]
Y
P
O
3 When the confirmation message appears, press SET.
Copying Clips
C
You can copy MXF clips from one CF card to the other. The copied clips will retain their original name.
Operating modes:
Copying a Single Clip
1 Select the desired clip and then press SET to open the clip menu.
2 Select [Copy Clip] and then press SET.
• The clip information screen appears and it prompts you to confirm the operation. You can also check the
available space on both CF cards.
3 Select [OK] and then press SET.
• Select [Cancel] instead to cancel the operation.
• While the clip is being copied, you can press SET to cancel.
4 When the confirmation message appears, press SET.
• The selected clip is copied to the other CF card and the screen changes back to the MXF clip index screen.
Copying Multiple Clips
1 Open the [Copy] submenu.
[w Other Functions] > [Clips] > [Copy]
2 Select [Select] to select which clips to copy, [$ Mark] to copy all the
clips with an $ mark, or [All] to copy all the clips, and then press SET.
[w Other Functions]
[Clips]
[Copy]
Clip Operations
• If you selected [Select], use the joystick to move between the clips. Press SET to select a clip to copy and
repeat as necessary (up to 100 clips). After selecting all the desired clips, press the MENU button.
154
3 Select [OK] and then press SET.
• All the applicable clips on the selected CF card will be copied to the other CF card.
• Select [Cancel] instead to cancel the operation.
• While the clips are being copied, you can press SET to cancel.
4 When the confirmation message appears, press SET.
NOTES
• You cannot copy a clip if either CF card slot cover is open.
• If a clip is being copied to a card that already has a clip with the same number (the last 4 digits in the clip
name), the copied clip will be renamed with the following number.
Deleting Clips
You can delete any clip except for MXF clips with an $ mark. To delete such clips, delete the $ mark
beforehand.
Operating modes:
Deleting a Single Clip
Y
P
O
1 Select the desired clip and then press SET to open the clip menu.
C
2 Select [Delete Clip] (MXF clips) or [Delete] (MP4 clips) and then press SET.
• You will be prompted to confirm the operation. For MXF clips only, the clip information will be displayed on
the screen as well.
3 Select [OK] and then press SET.
• Select [Cancel] instead to cancel the operation.
• While the clip is being deleted, the operation cannot be canceled.
4 When the confirmation message appears, press SET.
Deleting Multiple Clips
1 Open the [Delete] submenu.
[w Other Functions] > [Clips] > [Delete]
2 Select [Select] to select which clips to delete or [All] to delete all the
clips and then press SET.
• If you selected [Select], use the joystick to move between the clips.
Press SET to select a clip to delete and repeat as necessary (up to
100 clips). After selecting all the desired clips, press the MENU button.
3 Select [OK] and then press SET.
• All the applicable clips on the selected recording media will be deleted.
• Select [Cancel] instead to cancel the operation.
• While the clips are being deleted, you can press SET to cancel.
4 When the confirmation message appears, press SET.
[w Other Functions]
[Clips]
[Delete]
Clip Operations
Deleting the User Memo and GPS Information
Operating modes:
1 Select the desired clip and then press SET to open the clip menu.
155
2 Select [Delete User Memo] and then press SET.
• The user memo and GPS information is deleted and the screen changes back to the MXF clip index screen.
• Select [Cancel] instead to cancel the operation.
Copying a Custom Picture File Embedded in a Clip
You can copy the custom picture file embedded in an MXF clip to the camcorder.
Operating modes:
Y
P
O
1 Select the desired clip (a clip with the / icon) and then press SET to open the clip menu.
2 Select [Copy / File] and then press SET.
• The [/ Data 1/3] screen appears with the orange selection frame indicating a custom picture file slot in the
camcorder.
• You can push the joystick up/down to display the [/ Data 2/3] and [/ Data 3/3] screens.
C
3 Push the joystick left/right to select the desired file slot and then press SET.
4 Select [OK] and then press SET.
• The custom picture file already in the selected file slot will be overwritten.
• Select [Cancel] instead to cancel the operation.
5 When the confirmation message appears, press SET.
NOTES
• You cannot copy the custom picture file to a file slot that contains a protected custom picture file.
• By default, file slot [C9] is protected.
Displaying an Index Screen of Shot Marks
After you add shot marks to an MXF clip, you can display an index screen that contains all the frames in a clip
with either shot mark, only the " mark or only the # mark. When you play back a clip from this index screen,
playback will start from the frame indicated by the shot mark. You can also perform other operations from this
index screen, such as adding and deleting shot marks.
Operating modes:
1 Select the desired clip (a clip with the ! icon) and then press SET to open the clip menu.
2 Select [Shot Mark] and then press SET.
• The [Shot Mark] index screen appears, which contains all the frames with shot marks in the clip. Select
instead [Shot Mark 1] to display an index screen only of the frames with the " mark or [Shot Mark 2] to
display an index screen only of the frames with the # mark.
English
• The [Delete User Memo] screen appears and it prompts you to confirm the operation.
3 Select [OK] and then press SET.
Clip Operations
• The time code under the thumbnail indicates the time code of the frame with the shot mark.
• Press the INDEX button or CANCEL button to return to the MXF clip index screen.
156
Time code of the
frame with the
shot mark
NOTES
• After you finish playing back a clip from this index screen, the index screen that was open before the [Shot
Mark] index screen will appear.
Y
P
O
Displaying a Frame Index Screen of a Single Clip
You can display an index screen of a single MXF clip broken down as frames at fixed intervals. This is useful
when you have a long clip or wish to play back a clip from a certain point. You can change how many thumbnails
are displayed. You can also perform other operations from this index screen, such as adding and deleting shot
marks.
C
Operating modes:
1 Select the desired clip and then press SET to open the clip menu.
2 Select [Expand Clip] and then press SET.
• The [Expand Clip] index screen appears, which shows thumbnails of frames taken from the clip at fixed
intervals. The time code under the thumbnail indicates the time code of the frame.
• You can change the fixed interval between frames by showing more or fewer thumbnails. To show more
thumbnails, open the clip menu and select [More Index Pics] and then press SET. To show fewer
thumbnails, select [Fewer Index Pics] and then press SET.
• Press the INDEX button or CANCEL button to return to the MXF clip index screen.
Thumbnail icon:
Indicates the frame
used as the clip
thumbnail in the
MXF clip index
screen.
Time code of the
displayed frame
NOTES
• After you finish playing back a clip from this index screen, the index screen that was open before the [Expand
Clip] index screen will appear.
Clip Operations
Adding Shot Marks
You can add shot marks (", # or both) to shots in an MXF clip you want to set apart. Later, you can display an
index screen that shows only the clips with a " mark, only the clips with a # mark, or only clips with either shot
mark.
157
Operating modes:
English
Adding Shot Marks during Playback
To add an " mark or # mark to a clip during playback or playback pause, you must first set an assignable
button to [Add Shot Mark 1] or [Add Shot Mark 2] in advance.
1 Set an assignable button to [Add Shot Mark 1] or [Add Shot Mark 2] (A 129).
2 During playback or playback pause, press the assignable button at the point in the clip where you
want to add the shot mark.
• A message indicating the shot mark appears on the screen and the shot mark is added to the clip.
• Adding a shot mark to a clip during playback will pause the playback.
Y
P
O
Adding Shot Marks from the Index Screen
1 Open the [Shot Mark] index screen or [Expand Clip] index screen.
2 Select the desired frame (thumbnail) and then press SET to open the clip menu.
3 Select [Add Shot Mark 1] or [Add Shot Mark 2] and then press SET.
• The clip information screen appears and it prompts you to confirm the operation.
4 Select [OK] and then press SET.
• The screen changes back to the previous index screen and the selected shot mark appears next to the
selected clip’s thumbnail.
• Select [Cancel] instead to cancel the operation.
C
NOTES
• You can also add " marks (only) using the SHOT1 button on the supplied wireless controller.
• Up to 100 shot marks (" and # marks combined) can be added to a single MXF clip.
• There may be up to a 0.5 second delay from when you press the button to when the camcorder adds the shot
mark.
Deleting Shot Marks
Operating modes:
1 Open the [Shot Mark] index screen or [Expand Clip] index screen.
2 Select the desired frame (thumbnail) and then press SET to open the clip menu.
3 Select [Del. Shot Mark 1] or [Del. Shot Mark 2] and then press SET.
• The clip information screen appears and it prompts you to confirm the operation.
4 Select [OK] and then press SET.
• The selected mark is deleted and the screen changes back to the previous index screen.
• If a frame has no shot marks, it will no longer appear in the [Shot Mark] index screen.
• Select [Cancel] instead to cancel the operation.
Clip Operations
Changing a Clip’s Thumbnail
You can change the thumbnail that appears in the MXF clip index screen to one of the other frames that appear
in the [Shot Mark] index screen or [Expand Clip] index screen.
158
Operating modes:
1 Open the [Shot Mark] index screen or [Expand Clip] index screen.
2 Select the desired frame (thumbnail) and then press SET to open the clip menu.
3 Select [Set Index Picture] and then press SET.
• The clip information screen appears and it prompts you to confirm the operation.
4 Select [OK] and then press SET.
• The selected frame is set as the clip’s thumbnail and the screen changes back to the previous index screen.
R appears next to the thumbnail of the selected frame.
• Select [Cancel] instead to cancel the operation.
NOTES
• When playing back a clip from the MXF clip index screen, playback will start from the beginning of the clip,
regardless of the thumbnail.
C
Y
P
O
6
External Connections
159
Video Output Configuration
*
only.
Recording Video Signal Configuration and Video Output Configuration by Terminal
Refer to the following table for the video output configuration from each terminal, depending on the recording
video configuration used.
Operating modes:
3G/HD-SDI terminal and MON. terminal
Recording video configuration
Bit rate
Frame rate
59.94P5
1920x1080
59.94i6
29.97P
23.98P
59.94P
1280x720
29.97P
23.98P
1
2
3
4
5
6
Y
P
O
3G/HD-SDI terminal output
[3G/HD-SDI]
[Direct]
MON. terminal output1
setting2
[MON.] setting3
4
[Compatible]
[HD]
1080/59.94i
1080/59.94i
1080/29.97P
1080/29.97PsF
1080/29.97PsF
1080/23.98P
1080/59.94i
1080/59.94i
720/59.94P
720/59.94P
C
1080/59.94P
1080/59.94i
720/59.94P
720/29.97P
720/23.98P
Onscreen displays can be superimposed and output to an external monitor (A 165).
[¢ Video Setup] > [3G/HD-SDI].
[¢ Video Setup] > [MON.].
The zebra pattern can be output to an external monitor (A 89).
MP4 clips only.
MXF clips only.
[SD]
480/59.94i
English
The video signal output from the 3G/HD-SDI terminal*, MON. terminal*, HDMI OUT and AV OUT terminals
depends on the clip’s video configuration, the capability of the external monitor (for video output from the HDMI
OUT terminal) and on various menu settings.
Video Output Configuration
HDMI OUT terminal and AV OUT terminal
HDMI OUT terminal output1
Recording video configuration
Bit rate
160
Frame rate
59.94P5
AV OUT
terminal output1
(SD output)
[MON.] setting2
[HD]3
[SD]
[Off]4
1080/59.94P7
1080/59.94P7
1080/59.94i
1080/59.94i or
480/59.94P
6
59.94i
1920x1080
29.97P
23.98P
480/59.94i
480/59.94i
59.94P
1280x720
29.97P
720/59.94P or
480/59.94P
720/59.94P
23.98P
1
2
3
4
5
6
7
Onscreen displays can be superimposed and output to an external monitor (A 165).
[¢ Video Setup] > [MON.].
The zebra pattern can be output to an external monitor (A 89).
The video signal will change automatically depending on the capability of the external monitor.
MP4 clips only.
MXF clips only.
Only when [¢ Video Setup] > [3G/HD-SDI] is set to a setting other than [Compatible] and [¢ Video Setup] > [HDMI] is set
to [+1920x1080 59.94P].
Y
P
O
Playback Video Configuration and Video Output Configuration by Terminal
Refer to the following tables for the video output configuration from each terminal, depending on the video
configuration of the clip being played back.
Operating modes:
C
3G/HD-SDI terminal and MON. terminal
Video configuration of the clip
Movie format
1
2
[MON.] setting2
Bit rate
Frame rate
1920x1080
59.94i /
29.97P /
23.98P
1080/59.94i
1080/59.94i
1280x720
59.94P /
29.97P /
23.98P
720/59.94P
720/59.94P
1920x1080 /
1280x720 /
640x360
59.94P /
29.97P /
23.98P
1080/59.94P
1080/59.94i
MXF
MP4
MON. terminal output1
3G/HD-SDI terminal
output
[HD]
Onscreen displays can be superimposed and output to an external monitor (A 165).
[¢ Video Setup] > [MON.].
[SD]
480/59.94i
Video Output Configuration
HDMI OUT terminal and AV OUT terminal
HDMI OUT terminal output1
Video configuration of the clip
Movie format
Frame rate
1920x1080
59.94i /
29.97P /
23.98P
1080/59.94i
1280x720
59.94P /
29.97P /
23.98P
720/59.94P
59.94P
1080/59.94P4
29.97P /
23.98P
1080/59.94i
1
2
3
4
1920x1080 /
1280x720 /
640x360
[HD]
[SD]
1080/59.94i or
480/59.94i
480/59.94i
Onscreen displays can be superimposed and output to an external monitor (A 165).
[¢ Video Setup] > [MON.].
The video signal will change automatically depending on the capability of the external monitor.
Only when [¢ Video Setup] > [HDMI] is set to [+1920x1080 59.94P].
C
[Off]3
AV OUT terminal
output1
(SD output)
Y
P
O
720/59.94P or
480/59.94i
1080/59.94P4
1080/59.94i or
480/59.94i
161
English
Bit rate
MXF
MP4
[MON.] setting2
480/59.94i
Connecting to an External Monitor
Connecting to an External Monitor
162
When you connect the camcorder to an external monitor for recording or playback, use the terminal on the
camcorder that matches the one you wish to use on the monitor. Then, select the video signal output
configuration (A 159). The camcorder can output video from all of the video output terminals simultaneously.
Operating modes:
Connection Diagram
We recommend that you power the camcorder from a household power outlet using the compact power adapter.
AV OUT
terminal
C
Y
P
O
MON. terminal
HDMI OUT
terminal
3G/HD-SDI
terminal
HDMI cable
(commercially
available)
STV-250N
Stereo Video
Cable (optional)
BNC cable
(commercially
available)
HDMI IN
AV IN
3G-SDI IN or HD SDI IN
HD SDI IN or SDI IN
Connecting to an External Monitor
Using the 3G/HD-SDI Terminal
[¢ Video Setup]
The digital signal output from the 3G/HD-SDI terminal includes the video
signal, audio signal (2 or 4 channels) and time code signal. If necessary,
perform the following procedure to activate the terminal and select the
type of signal output. Turning the output off will conserve the camcorder’s
power.
[3G/HD-SDI]
English
1 Open the [3G/HD-SDI] submenu.
[¢ Video Setup] > [3G/HD-SDI]
2 Select the desired option and then press SET.
3 To select the mapping mode for 1080/59.94P output, open the
[3G-SDI Mapping] submenu.
[¢ Video Setup] > [3G-SDI Mapping]
[¢ Video Setup]
[3G-SDI Mapping]
[Level B]
4 Select the desired option and then press SET.
• You can select a video output signal compliant with Level A or Level B
of the SMPTE ST 425-1 standard.
Y
P
O
Options
[Direct]1:The video recording signal is output unchanged.
[Compatible]1: The video signal output is compatible with most external monitors.
[On]2:There is video output from the terminal.
[Off]:No video output from the terminal.
1
mode only.
2
163
[Off]
mode only.
C
NOTES
• If necessary, you can superimpose the onscreen displays on the video displayed on the external monitor
(A 165).
Using the MON. Terminal
The digital signal output from the MON. terminal also includes the video
signal, audio signal (2 or 4 channels) and time code signal. If necessary,
perform the following procedure to activate the terminal and change the
output to HD or SD. Turning the output off will conserve the camcorder's
power.
[¢ Video Setup]
[MON.]
[Off]
1 Open the [MON.] submenu.
[¢ Video Setup] > [MON.]
2 Select the desired option and then press SET.
• If you selected [SD], you can select the SD output method (A 165).
NOTES
• If necessary, you can superimpose the onscreen displays on the video displayed on the external monitor
(A 165).
Connecting to an External Monitor
Using the HDMI OUT Terminal
164
The HDMITM OUT terminal also offers a digital connection and outputs both a video and audio signal (2 channels
only).
The output of the HDMI OUT terminal depends on the [¢ Video Setup] > [3G/HD-SDI], [MON.] and
[HDMI] settings. When [¢ Video Setup] > [MON.] is set to [Off], the output signal will switch automatically
depending on the capability of the external monitor.
The output of the HDMI OUT terminal depends on the [¢ Video Setup] > [HDMI] setting and the
capability of the external monitor.
1
If necessary, check the settings for the 3G/HD-SDI
terminal (A 163) and MON. terminal (A 163), as they can affect
the output from the HDMI OUT terminal as well.
• To use the 1080/59.94P video output, set [¢ Video Setup] > [3G/
HD-SDI] to [Direct] or [Off].
• For details, refer the video output configuration tables (A 159).
[¢ Video Setup]
[HDMI]
[Normal]
2 Open the [HDMI] submenu.
[¢ Video Setup] > [HDMI]
3 Select [Normal] (no 1080/59.94P output) or [+1920x1080/59.94P] and then press SET.
Y
P
O
NOTES
• The HDMI OUT terminal is for output only. Do not connect the camcorder to another device’s output terminal
using the HDMI OUT terminal as this will cause a malfunction.
• Correct operation cannot be guaranteed when connecting the camcorder to DVI monitors.
• Video may not be output correctly depending on the monitor. In such case, use another terminal.
• If necessary, you can superimpose the onscreen displays on the video displayed on the external monitor
(A 165).
• However, when [HDMI] is set to [+1920x1080/59.94P], onscreen displays will not be superimposed during the
output of 1080/59.94P video. In
mode and in
mode during playback, only the live/playback
image will be displayed on the external monitor; while the [MP4] or [Photos] index screen appears on the
camcorder’s screen, only the thumbnails of the clips or photos will be displayed on the external monitor.
• You can select the SD output method (A 165).
C
Using the AV OUT Terminal
When you output video from the AV OUT terminal, the video signal is converted to an analog SD composite
video signal. In addition, the AV OUT terminal also outputs audio. You can select the SD output method
(A 165).
NOTES
• When you play back a clip on a monitor with a 4:3 aspect ratio, the monitor will switch automatically to
widescreen mode if it is compatible with the Video ID-1system.
• If necessary, you can superimpose the onscreen displays on the video displayed on the external monitor
(A 165).
Connecting to an External Monitor
SD Output
When HD video with a 16:9 aspect ratio is converted and output from the
MON. terminal*, HDMI OUT terminal or AV OUT terminal as SD video with
a 4:3 aspect ratio, you can choose how it appears on the external
monitor.
*
only.
[¢ Video Setup]
[HD/SD Output]
[Resize SD Output]
[Letterbox]
[¢ Video Setup] > [HD/SD Output] > [Resize SD Output]
2 Select the desired option and then press SET.
Options
[Letterbox]:The 16:9 aspect ratio is maintained but black letterbox bars are added to the top and bottom of the image.
[Squeeze]:The image is squeezed from the left and right so that the entire image fits within the screen. The image will
appear normal if the external monitor also has a 16:9 aspect ratio.
[Side Crop]:The left and right sides of the image are cropped so that the central part of the image fits within the screen.
[Letterbox] setting
Y
P
O
[Squeeze] setting
Superimposing Onscreen Displays to Appear on an
External Monitor
C
You can choose to superimpose onscreen displays on the video output
from the MON. terminal*, HDMI OUT terminal or AV OUT terminal. Doing
so will display the onscreen displays on an external monitor. You can set
this function separately for HD and SD output. This setting will not affect
your recordings.
*
[Side Crop] setting
[¢ Video Setup]
[HD/SD Output]
[HD Onscreen Displays]
[SD Onscreen Displays]
only.
1 Open the [HD Onscreen Displays] or [SD Onscreen Displays]
submenu.
[Off]
[¢ Video Setup] > [HD/SD Output] > [HD Onscreen Displays] or [SD Onscreen Displays]
2 Select [On] and then press SET.
• If [£ OLED/VF Setup] > [Custom Display 2] > [Output Display] is set to [On], T appears on the
upper right of the screen.
NOTES
• Onscreen displays will not appear on an external monitor for SD output if [¢ Video Setup] > [HD/SD
Output] > [Resize SD Output] is set to [Side Crop].
• If you set an assignable button to [Onscreen Display] (A 129), you can press the button to turn on and off the
superimposing of onscreen displays on video output from the camcorder’s terminals (simultaneously for HD
and SD video).
English
1 Open the [Resize SD Output] submenu.
Original image (16:9)
165
Audio Output
Audio Output
166
The camcorder can output audio from the 3G/HD-SDI terminal*, MON. terminal*, HDMI OUT terminal, AV OUT
terminal or × (headphone) terminal. When audio is output from the AV OUT terminal or × (headphone) terminal,
you can configure settings such as the output channel. When audio is output from the AV OUT terminal, you can
select the output level. Additionally, during playback of MXF clips recorded with 4-channel audio, you can select
the channels output from the HDMI OUT terminal.
*
only.
Selecting the Audio Channel
You can select the audio channels that are output from the various terminals.
Audio Output from the AV OUT Terminal or × (headphone) Terminal
Operating modes:
1 Open the [Monitor Channels] submenu.
Y
P
O
[¡ Audio Setup] > [Audio Output] > [Monitor Channels]
2 Select the desired option and then press SET.
• The icon of the selected channels will appear on the right of the
screen, above the audio level meter.
NOTES
• If you set an assignable button to [Monitor Channels] (A 129), you can
press the button to cycle through the audio channel options.
C
[¡ Audio Setup]
[Audio Output]
[Monitor Channels]
[CH1/CH2]
Audio Output from the HDMI OUT Terminal
During 2-channel audio recording, the audio channels output from the
HDMI OUT terminal are [CH1/CH2] and cannot be changed. During the
recording/playback of MXF clips with 4 audio channels, you can select
which two channels to output from the HDMI OUT terminal.
[¡ Audio Setup]
[Audio Output]
[HDMI Channels]
Operating modes:
[CH1/CH2]
1 Open the [HDMI Channels] submenu.
[¡ Audio Setup] > [Audio Output] > [HDMI Channels]
2 Select the desired option and then press SET.
Options
Setting
Audio output
L
R
[CH1/CH2]
CH1
CH2
[CH1/CH1]
CH1
CH1
[CH2/CH2]
CH2
CH2
CH1+CH2 mixed
CH1+CH2 mixed
[CH3/CH4]*
CH3
CH4
[CH3/CH3]*
CH3
CH3
[CH4/CH4]*
CH4
CH4
[CH1+2/CH1+2]
Audio Output
Audio output
Setting
L
R
[CH3+4/CH3+4]*
CH3+CH4 mixed
CH3+CH4 mixed
[CH1+3/CH2+4]*
CH1+CH3 mixed
CH2+CH4 mixed
167
* Only available during the recording/playback of MXF clips with 4 audio channels.
English
Synchronizing the Video with the Audio being Monitored
When audio is output from the AV OUT terminal or × (headphone)
terminal, you can choose to synchronize the audio signal with the video
signal or have the camcorder output the audio in real time.
[¡ Audio Setup]
[Audio Output]
[Monitor Delay]
Operating modes:
[Normal]
1 Open the [Monitor Delay] submenu.
[¡ Audio Setup] > [Audio Output] > [Monitor Delay]
Y
P
O
2 Select the desired option and then press SET.
Options
[Line Out]:Synchronizes the audio and video signals.
[Normal]:Allows you to monitor the audio in real time. There will be a slight delay between the audio and video.
NOTES
• The audio and video signals recorded will be synchronized, regardless of the [Monitor Delay] setting.
C
Selecting the Output Level of the AV OUT Terminal
You can select the output level of audio that is output from the AV OUT
terminal.
[¡ Audio Setup]
[Audio Output]
Operating modes:
[Level]
1 Open the audio ouput [Level] submenu.
[¡ Audio Setup] > [Audio Output] > [Level]
2 Select the desired level and then press SET.
Options
[1 Vrms]:The audio output level is normal.
[2 Vrms]:The audio output level is 6 dB higher.
NOTES
• This setting does not affect audio output to headphones.
[1 Vrms]
Saving Clips to a Computer
Saving Clips to a Computer
168
The software used to save your clips on a computer depends on the movie format of the clips. Use Canon XF
Utility to save MXF clips or one of the Canon XF plugins* to import MXF clips into a non-linear editing (NLE)
software. Use the supplied software Data Import Utility to save MP4 clips.
* Plugins are available for NLE software by Avid and Apple.
Saving MXF Clips
Canon XF Utility and the Canon XF plugins are available for free download from your local Canon Web site.
Refer to the Web site for the system requirements and the latest information about the software and plugins.
Canon XF Utility: Browser for transferring clips to a computer, playing back and checking video, and managing
clips.
Plugins for non-linear editing (NLE) software: The plugins allow you to transfer clips from a computer or a CF
card (connected via USB reader to a computer) to the NLE software. The following plugins are available.
- Canon XF Plugin 64 for Avid Media Access (Windows or Mac OS)
- Canon XF Plugin for Final Cut Pro/Final Cut Pro X (Mac OS)
Y
P
O
For details about using the software, refer to the instruction manual (PDF file) that is installed with the software/
plugin. Refer to Viewing the Software Instruction Manuals (A 170) for details on accessing the manuals.
The following procedures for Windows systems are written based on a computer running Windows 7. The
procedure may be different for other versions. For details see the Help modules of the operating system.
Operating modes:
C
Installing Canon XF Utility (Windows)
1 Double-click the file that you downloaded from the Canon Web site to decompress it.
• The file is xuw*****.zip for Canon XF Utility or xpmw*****.zip for Canon XF Plugin 64 for Avid Media Access.
The rest of the explanation refers only to Canon XF Utility but the procedure is similar for the Canon XF
plugin.
• The folder xuw***** will be created that contains the file xuw***.exe.
2 Double-click xuw***.exe.
3 Follow the onscreen instructions to select your area (continent), country/region and/or language, as necessary.
• Available options will vary depending on your country/region.
4 After the message appears prompting you to exit other applications, exit other applications and then click OK.
• The software’s license agreement appears.
5 Read the license agreement and click Yes to begin the installation.
• If you do not select Yes, you cannot install the software.
• When the installation has completed, Installation has completed successfully appears.
6 Click Next and then click Finish.
Uninstalling Canon XF Utility (Windows)
1 From the Start menu, select All Programs > Canon Utilities > Canon XF Utility > Uninstall Canon XF
Utility.
• A confirmation screen appears.
2 Click Yes to begin uninstalling the software.
• When the software has been uninstalled, The software has been successfully uninstalled appears.
3 Click OK.
Saving Clips to a Computer
Uninstalling Canon XF Plugin 64 for Avid Media Access and Canon XF MPEG2 Decoder
(Windows)
1 In the Control Panel, open Programs and Features or Add or Remove Programs.
• A list of installed programs appears.
2 Select the plugin/decoder you wish to uninstall.
Uninstalling the Canon XF Plugin 64 for Avid Media Access Instructions
1 From the Start menu, open All Programs > Canon Utilities > Canon XF Plugin 64 for Avid Media Access
> Uninstall Canon XF Plugin 64 for Avid Media Access Instruction Manual.
2 When the confirmation screen appears, click Yes and then click OK.
Installing Canon XF Utility (Mac OS)
1 Double-click the file that you downloaded from the Canon Web site to decompress it.
• The downloaded file is xum*****.dmg.gz for Canon XF Utility, xpmm*****.dmg.gz for Canon XF Plugin for
Avid Media Access, or xpfm*****.dmg.gz for Canon XF Plugin for Final Cut Pro/Final Cut Pro X. The rest of
the explanation refers only to Canon XF Utility but the procedure is similar for the Canon XF plugins.
• The file xum*****.dmg will be created.
2 Double-click xum*****.dmg.
• The xum*** icon will appear on the desktop.
Y
P
O
3 Double-click xum*** and then double-click XUMInstaller.
4 Follow the onscreen instructions to select your area (continent), country/region and/or language, as necessary.
• Available options will vary depending on your country/region.
C
5 After the message appears prompting you to exit other applications, exit other applications and then click OK.
• The software’s license agreement appears.
6 Read the license agreement and click Yes to begin the installation.
• If you do not select Yes, you cannot install the software.
• When the installation has completed, Installation has completed successfully appears.
7 Click Next and then click Finish.
Uninstalling the Software (Mac OS)
Drag and drop to Trash the file or folder corresponding to the item you wish to uninstall.
Software/Plugin/Manual
File/Folder
Canon XF Utility
/Applications/Canon Utilities/Canon XF Utility
Canon XF Plugin for Final Cut Pro
/Library/Application Support/ProApps/MIO/RAD/Plugins/CanonXF.RADPlug
Canon XF Plugin for Final Cut Pro X
/Library/Application Support/ProApps/MIO/RADPlugins/CanonXF64.RADPlug
Canon XF Plugin 64 for Avid Media Access
/Library/Application Support/ProApps/Avid/AVX2_Plug-ins/AMA/MVP_CanonXF64.avx
Canon XF MPEG2 Decoder
/Library/QuickTime/XFMpeg2Dec.component
Canon XF Plugin Instructions
/Applications/Canon Utilities/Desired plugin name
English
3 Click Uninstall or Uninstall/Change and follow the instructions to uninstall the plugin/decoder.
169
Saving Clips to a Computer
Viewing the Software Instruction Manuals
170
For details on using the software, refer to the instruction manual (PDF file) of each module. The instruction
manuals are installed with the software. You can also view the instruction manual by starting the Canon XF
Utility software and then selecting Help > View Instruction Manual.
Viewing the Canon XF Utility Instruction Manual
Windows:
1 From the Start menu, select All Programs > Canon Utilities > Canon XF Utility > Canon XF Utility
Instruction Manual.
2 Select the language of the instruction manual to view.
Mac OS:
1 From Applications, open Canon Utilities > Canon XF Utility > Manual.
2 Open the folder of the desired language and double-click the PDF file.
Viewing the Plugin Instructions
Windows:
1 From the Start menu, select All Programs > Canon Utilities > Canon XF Plugin 64 for Avid Media Access
> Canon XF Plugin 64 for Avid Media Access Instruction Manual.
2 Select the desired language.
Mac OS:
Y
P
O
1 From Applications, open Canon Utilities > Desired plugin name > Manual.
2 Open the folder of the desired language and double-click the PDF file.
Saving MP4 Clips
C
Using the supplied software Data Import Utility, you can save MP4 clips to a computer. Data Import Utility will
also automatically join multiple MP4 clips of a single scene that were split every 4 GB because of file size limits
and save them as a single video file.
For more details, refer to ‘Data Import Utility Software Guide’, a PDF file in the [\Manual\English] folder of the
supplied software CD-ROM.
IMPORTANT
• Before saving MP4 clips to your computer with Data Import Utility using an SD card reader or your
computer’s memory card slot, do not access or manipulate the files on the SD card with other software. Failing
to do so may result in not being able to save the files to your computer.
Installing Data Import Utility
See Installation and System requirements in the ‘Data Import Utility Software Guide’ Software Guide (PDF file) for
step-by-step installation instructions and system requirements.
Saving Clips to a Computer
Connecting the Camcorder to a Computer
Connect the camcorder to a computer using the optional IFC-400PCU USB cable. Use the appropriate software
as described in the previous sections to save your recordings.
171
Operating modes:
2 On the camcorder, hold down the button on the Q switch and slide the switch to MEDIA.
3 Connect the camcorder to the computer using the optional IFC-400PCU USB cable.
USB terminal
IFC-400PCU USB Cable
(optional)
C
Y
P
O
English
1 Power the camcorder using the compact power adapter.
Saving Clips to a Computer
172
C
Y
P
O
7
Network Functions
173
About the Network Functions
Network functions and connection types
Network function
Description
Wi-Fi
Wired
LAN
Infrastructure1
Camera Access
Point2
A
Browser Remote
Control the camcorder remotely from the Web
browser of a connected device.
Ü
–
Ü
182
Real-Time Proxy Transfer
Send a proxy video file from the camcorder to a
connected device to save locally on the device.
–
–
Ü
188
FTP File Transfer
Transfer clips recorded with the camcorder to
another device connected to the network using
the FTP protocol.
Ü
Ü
Ü
189
Playback via Browser
Access the MP4 clips or photos recorded on the
SD card in the camcorder from the Web
browser of a connected device to play back or
save locally.
Ü
–
Ü
193
1
2
C
Y
P
O
Connection to a Wi-Fi network via an external access point (wireless router, etc.)
Direct connection to one Wi-Fi-enabled device where the camcorder serves as the Wi-Fi access point.
Before using the network functions
• The instructions in this chapter assume you already have a correctly configured and working network, network
device(s) and/or Wi-Fi access point. If necessary, refer to the documentation provided with the network
devices you want to use.
• Configuring the network settings requires adequate knowledge about configuring and using wired (Ethernet)
and/or wireless (Wi-Fi) networks. Canon cannot provide support regarding network configurations.
IMPORTANT
• Canon shall not be liable for any loss of data or damage resulting from incorrect network configuration or
settings. Additionally, Canon shall not be liable for any loss or damage caused by the use of network functions.
• Using an unprotected Wi-Fi network can expose your files and data to monitoring by unauthorized third
parties. Be aware of the risks involved.
NOTES
• About the Wi-Fi antenna: When using the camcorder's Wi-Fi functions,
do not cover the Wi-Fi antenna with your hand or other object. Covering
it may interfere with wireless signals.
• Do not open either of the CF card slot covers or the SD card slot cover
while using network functions.
English
After you connect the camcorder to a network via Wi-Fi (A 174) or wired LAN (A 179), you can use the
following network functions. You can save up to 5 network configurations and switch easily between them
depending on your working environment. You can check the current network settings on the status screens
(A 215) and change them if necessary (A 181).
Connecting to a Wi-Fi Network
Connecting to a Wi-Fi Network
174
The camcorder is Wi-Fi certified and can connect to a Wi-Fi network using an external access
point (wireless router) or can itself serve as a Wi-Fi access point. The camcorder can connect to
wireless routers (access points) compliant with the 802.11a/b/g/n protocol and are Wi-Fi certified
(bear the logo shown on the right).
The camcorder offers 5 ways to connect to a Wi-Fi network and the method you use will depend on the type and
specifications of the access point and network you want to use. Note that using an unprotected Wi-Fi network
can expose your data to monitoring by unauthorized third parties. Be aware of the risks involved.
Operating modes:
WPS (button): If your wireless router supports Wi-Fi Protected Setup (WPS), setup will be
easy and require minimal configuring and no passwords. To check if your wireless router
has a WPS button and for details about how to activate the Wi-Fi protected setup, refer to
the instruction manual of your wireless router.
WPS (PIN code): Even if your wireless router does not have a dedicated WPS button, it may support WPS using
a PIN code instead. For setup using a PIN code, you will need to know in advance how to activate the wireless
router’s WPS function. For details refer to the instruction manual of your wireless router.
Y
P
O
Searching for Access Points: If your access point does not support the WPS function or you cannot activate it,
you can have the camcorder search for access points in the area.
Manual Setup: If the access point you want to use has stealth mode activated and it cannot be automatically
detected by the camcorder, you can enter all the necessary settings manually. This requires more advanced
knowledge of Wi-Fi and network settings.
Camera Access Point: When shooting in a location where there are no access points available, the camcorder
can serve as a wireless access point*. Wi-Fi enabled devices will be able to connect to the camcorder directly.
C
* Limited only to the connection between the camcorder and supported Wi-Fi enabled devices. The functionality is not the same
as that of commercially available access points.
Wi-Fi Protected Setup (WPS)
Wi-Fi Protected Setup (WPS) is the easiest way to connect to a Wi-Fi access point. You can do simply by
pushing a button (if the access point (wireless router) you want to connect to has a WPS button) or using a PIN
code issued by the camcorder.
Wireless Routers with a WPS Button
1 Open the [Set Up New] submenu.
[w Other Functions] > [Network Settings] > [Connection Settings]
> [Set Up New]
2 Select the [WPS: Button] method.
[Wi-Fi] > [Infrastructure] > [WPS: Button]
3 Press and hold the WPS button on the wireless router.
• The length of time required to hold down the WPS button depends
on the wireless router. Refer to the instruction manual of your wireless
router and make sure the wireless router’s WPS function is activated.
[w Other Functions]
[Network Settings]
[Connection Settings]
[Set Up New]
Connecting to a Wi-Fi Network
4 Within 2 minutes, press SET on the camcorder.
• While [Connecting] appears on the screen, you can press SET or the CANCEL button to cancel the
operation.
• After the connection is correctly established, continue with the procedure to configure the IP address
assignment (A 178).
WPS using a PIN code
1 Open the [Set Up New] submenu.
[w Other Functions] > [Network Settings] > [Connection Settings] > [Set Up New]
2 Select the [WPS: PIN Code] method.
[Wi-Fi] > [Infrastructure] > [WPS: PIN Code]
• The camcorder will generate and display an 8-digit PIN code.
3 Enter the PIN code from step 2 into the wireless router’s WPS (PIN code) setup screen.
Y
P
O
• For most wireless routers, you must use a Web browser to access the setup screen.
• For details about how to access your wireless router’s settings and activate the Wi-Fi Protected Setup
(WPS) using a PIN code, refer to the instruction manual of your wireless router.
4 Within 2 minutes, press SET on the camcorder.
• While [Connecting] appears on the screen, you can press SET or the CANCEL button to cancel the
operation.
• After the connection is correctly established, continue with the procedure to configure the IP address
assignment (A 178).
Searching for Access Points
C
The camcorder will automatically detect access points in the vicinity. After you select the desired access point,
you only need to enter the selected network’s encryption key (password) to connect the camcorder.
1 Open the [Set Up New] submenu.
[w Other Functions] > [Network Settings] > [Connection Settings]
> [Set Up New]
2 Select the [Search for Access Points] method.
[Wi-Fi] > [Infrastructure] > [Search for Access Points]
• The camcorder will search for active access points in your area and
display a list of available options.
[w Other Functions]
[Network Settings]
[Connection Settings]
[Set Up New]
English
NOTES
• The [WPS: Button] method may not work correctly if there are several active access points in the area. In such
case try using [WPS: PIN Code] or [Search for Access Points] (A 175) instead.
175
Connecting to a Wi-Fi Network
3 Push the joystick up/down to select the desired access
point and then press SET.
176
Current access point/Total number
of active access points detected
• If the access point is encrypted (C), enter the encryption
key (password) with the following procedure. Otherwise,
continue with the procedure to configure the IP address
assignment (A 178).
Encrypted access point
Network name (SSID)
Encrypted Access Points
1 If necessary, select the WEP index key.
• This step is only necessary if the Wi-Fi network’s authentication method is set to [Shared Key] or if the
encryption method is set to [WEP].
2 To enter the [Encryption Key] (password), select [Input] and then press SET.
• Enter the password of the selected Wi-Fi network using the keyboard screen (A 176).
Y
P
O
3 Continue with the procedure to configure the IP address assignment (A 178).
NOTES
Valid encryption keys vary depending on the encryption method.
64-bit WEP encryption: 5 ASCII characters or 10 hexadecimal characters.
128-bit WEP encryption: 13 ASCII characters or 26 hexadecimal characters.
AES / TKIP encryption: 8 to 63 ASCII characters or 64 hexadecimal characters.
C
* Note: ASCII characters include the numbers 0 to 9, the letters a to z and A to Z and some punctuation marks and special
symbols. Hexadecimal characters comprise the numbers 0 to 9 and the letters a to f and A to F.
Using the Virtual Keyboard Screen
The virtual keyboard is displayed on the OLED screen.
1 Use the joystick to select a character and then press SET to
add it.
• If you are entering sensitive information, like a password, the
character you entered will change to “‹” after a moment to
protect the password.
• Use the arrows (ð/ñ/ò/ó) to change the position of the
cursor and the backspace character (™) to delete the last
character entered.
• Repeat this step as necessary to enter the desired text.
Current character / Character limit
2 After entering the desired text, select [OK] and then press SET to close the keyboard screen.
3 Back in the original screen, select [OK] and then press SET to confirm the text and continue.
Connecting to a Wi-Fi Network
Manual Setup
If you prefer, you can enter manually the details of the Wi-Fi network you want to connect to. Follow the
instructions on the screen to complete the procedure.
1 Open the [Set Up New] submenu.
[w Other Functions]
[Network Settings]
2 Select the [Manual] method.
[Wi-Fi] > [Infrastructure] > [Manual]
[Connection Settings]
3 To enter the [SSID] (network name), select [Input] and then press
SET.
[Set Up New]
• Enter the SSID (network name) of the selected Wi-Fi network using
the keyboard screen (A 176).
4 Select the Wi-Fi network’s authentication method and then press SET.
• If you selected [Shared Key], skip to step 6.
5 Select the Wi-Fi network’s encryption method and then press SET.
• If the authentication method is [Open], you can select [WEP] and continue to step 6, or [No encryption] and
skip to step 7.
• If the authentication method is [WPA-PSK] or [WPA2-PSK], you can select [TKIP] or [AES].
Y
P
O
6 Enter the encryption key as described in Encrypted Access Points (A 176).
7 Continue with the procedure to configure the IP address assignment (A 178).
Camera Access Point
C
In this mode the camcorder itself serves as a wireless access point to which other Wi-Fi-enabled devices can
connect. Follow the instructions on the screen to complete the procedure.
1 Open the [Set Up New] submenu.
[w Other Functions] > [Network Settings] > [Connection Settings]
> [Set Up New]
[w Other Functions]
[Network Settings]
2 Select the [Camera Access Point] method.
[Wi-Fi] > [Camera Access Point]
3 To enter the [SSID] (network name), select [Input] and then press
SET.
[Connection Settings]
• Enter the SSID (network name) the camcorder will use as a Wi-Fi
access point using the keyboard screen (A 176).
• The network name is needed to connect the network device to the
camcorder. If necessary, write it down.
[Set Up New]
4 Select the wireless connection mode (5 GHz band or 2.4 GHz band) and then press SET.
5 Select the channel and then press SET.
• Available channels will be different depending on the wireless connection mode selected in the previous
step.
6 Select the encryption method and then press SET.
• If you selected [Open/No encryption], skip to step 8. If you selected [WPA2-PSK/AES], continue with step 7.
7 Enter the encryption key as described in Encrypted Access Points (A 176).
• This encryption key (password) is needed to connect the network device to the camcorder. If necessary,
write it down.
177
English
[w Other Functions] > [Network Settings] > [Connection Settings]
> [Set Up New]
Connecting to a Wi-Fi Network
8 Continue with the procedure to configure the IP address assignment (A 178).
178 Configuring the IP Address Settings
At this point you need to configure the TCP/IP settings for the camcorder to be able to connect to a wired or
Wi-Fi network. If you need to configure the TCP/IP settings manually, consult the network administrator to obtain
the relevant information.
1 Select the method for assigning the IP address: Select [Automatic] or [Manual] and then press SET.
• If you selected [Automatic], IP settings will be assigned automatically. Continue with the procedure to review
and save the configuration (A 178).
2 If you selected [Manual], enter manually the IP address assigned to the camcorder.
• Push the joystick up/down to select a value for the first field and then press SET to move to the next field.
After completing the four fields of an address, select [Set] and then press SET to confirm the address.
3 Enter the [Subnet Mask] and [Default Gateway] addresses in the same way.
• For Camera Access Point connections, the rest of the procedure is not necessary. Continue with the
procedure to review and save the configuration (A 178).
Y
P
O
4 Select the method for setting up the DNS server: Select [Do not use DNS] or [Manual].
• If you selected [Do not use DNS], a DNS server will not be used. Continue with the procedure to review and
save the configuration (A 178).
5 If you selected [Manual], enter the [Primary DNS Server] and [Secondary DNS Server] using the
method described in step 2.
• After entering the secondary DNS server, continue with the procedure to review and save the configuration
(A 178).
Saving the Configuration
C
1 Review the access point’s configuration and then press SET.
• The first screen shows the access point’s SSID and the type of connection. Push the joystick up/down to
review additional settings before pressing SET.
2 Select the desired configuration number and then press SET.
• You can save up to 5 different network configuration profiles in the camcorder. If you select a configuration
number that was already in use, the previous configuration will be overwritten by the new one.
3 To change the [Network Configuration Name], select [Input] and then press SET.
• If you wish, you can give the network configuration profile a more descriptive name to make it easier to
identify. Enter the desired name using the keyboard screen (A 176).
4 Select [OK] and then press SET to save the network configuration.
5 When the confirmation screen appears, press SET.
Connecting to a Wired (Ethernet) Network
Connecting to a Wired (Ethernet) Network
Connect the camcorder to a router or other device connected to a wired (Ethernet) network using a
commercially available LAN cable. Use Category 5e, shielded twisted pair (STP) LAN cables compatible with
Gigabit Ethernet (1000BASE-T) with good shielding capability.
English
LAN access indicator
LAN port on a
network device
LAN cable
(commercially available)
Y
P
O
1 Connect a commercially available LAN cable to the LAN terminal on the camcorder and a LAN port
on a network device.
2 Open the [Set Up New] submenu.
[w Other Functions] > [Network Settings] > [Connection Settings]
> [Set Up New]
3 Select [Ethernet] and then press SET.
C
179
• Continue with the procedure to configure the IP address assignment
(A 178).
[w Other Functions]
[Network Settings]
[Connection Settings]
[Set Up New]
Selecting a Network Connection
Selecting a Network Connection
180
You can save up to 5 different network configuration profiles. You can select which one to use depending on
where you plan to use the camcorder. If you just saved a new network configuration (A 178), that network
configuration will already be automatically selected and this procedure is not required.
1 Open the [Select] submenu.
[w Other Functions] > [Network Settings] > [Connection Settings]
> [Select]
2 Select the desired configuration number and then press SET.
• The camcorder will connect to the selected network only when you
activate a network function. The icon displayed on the top left of the
screen will indicate the type of network selected and the connection
status. Refer to the following table.
Connection type
Onscreen
display
Connection status
Wi-Fi
(Infrastructure)
In yellow: The camcorder is connecting to or disconnecting from
the network. In white: The network function can be used.
Wi-Fi
(Camera Access Point)
In yellow: Starting the camcorder’s access point. In white: The
camcorder’s access point is ready. Connect the Wi-Fi enabled
device to the camcorder.
• On the device: Open the Wi-Fi settings screen and select the
network name (SSID) that was set in the camcorder. If
necessary, enter the password set in the camcorder (A 177).
LAN (Ethernet)
In yellow: The camcorder is connecting to or disconnecting from
the network. The LAN access indicator will flash as well.
In white: The network function can be used. The LAN access
indicator will illuminate as well.
• If you set [w Other Functions] > [LAN (Ethernet) LED] to [Off],
the LAN access indicator will not illuminate.
C
Y
P
O
[w Other Functions]
[Network Settings]
[Connection Settings]
[Select]
Connection type
Changing Network Settings
Changing Network Settings
You can edit the settings of the currently selected network configuration profile even after the initial setup.
Changing settings manually requires more advanced knowledge of Wi-Fi and network settings. Turn off any
active network functions and wait until the network icons disappear from the screen before starting the
procedure.
2 Open the [Edit] submenu.
[w Other Functions] > [Network Settings] > [Connection Settings]
> [Edit]
[w Other Functions]
3 Continue with one of the following procedures depending on the
settings you wish to change.
[Network Settings]
[Connection Settings]
Changing Network Settings
4 Select [Settings] and then press SET.
[Edit]
5 If in step 1 you selected a Wi-Fi connection, select [Infrastructure]
or [Camera Access Point].
• Continue the procedure as described in Manual Setup (A 177, from step 3) or Camera Access Point
(A 177, from step 3).
Y
P
O
If in step 1 you selected a LAN connection, select [Automatic] or [Manual] and then press SET.
• If you selected [Automatic], IP settings will be assigned automatically and no further settings are necessary.
Select [OK] and then press SET twice to save the configuration.
• If you selected [Manual], continue the procedure as described in Manual Setup (A 177, from step 3).
C
Renaming the Configuration Profile
Each network configuration profile is stored under a configuration number ([No. 1] to [No. 5]). You can rename it
with a more familiar name to make it easier to distinguish between various networks you use.
4 Select [Rename] and then press SET.
5 To enter the new [Network Configuration Name], select [Input] and then press SET.
• Enter the desired network configuration name using the keyboard screen (A 176).
English
1 Select the network configuration profile whose settings you want to change (A 180).
181
Browser Remote: Controlling the Camcorder from a Network Device
Browser Remote: Controlling the Camcorder from a Network
Device
182
After connecting the camcorder to a network (Wi-Fi or using the LAN terminal), you can control the camcorder
remotely from the Web browser of a connected network device* using the Browser Remote application. Browser
Remote lets you monitor the image through live view, start and stop recording and remotely control the shutter
speed, gain and other settings. You can also create, edit and transfer a metadata profile** and check the
recording media, remaining recording time, time code, etc.
* For details about compatible devices, operating systems, Web browsers, etc., please visit your local Canon Web site.
**MXF clips only.
Operating modes:
Setting Up Browser Remote
Camcorder Settings
You can set a unique camcorder identification code and designate the port that the Browser Remote application
should use when accessing the camcorder through network. The port number (HTTP protocol) used by Browser
Remote is usually set to port 80, but you can change it if necessary. The camcorder ID will appear on the
Browser Remote screen, making it easy to identify which camcorder the application is controlling in case of a
multi-camera shooting setup.
1 Open the [Camera Settings] submenu.
Y
P
O
[w Other Functions] > [Network Settings] > [Remote Settings] >
[Camera Settings]
C
[w Other Functions]
2 Push the joystick up/down to select a value for the first digit of
the port number and then press SET to move to the next digit.
[Network Settings]
3 After completing all the digits, select [Set] and then press SET to
confirm the port number.
[Remote Settings]
4 To enter the [Camera ID], select [Input] and then press SET.
[Camera Settings]
• Enter the desired camcorder ID using the keyboard screen (A 176).
5 Select [OK] and then press SET to save the network
configuration.
6 When the confirmation message appears, press SET.
User Settings
A user name and password are required before the Browser Remote application can access and operate the
camcorder. You can set up to three different users and select whether you want to allow single-user operation
(full control) or two-user operation (one controlling camcorder functions and another in charge of metadata input
for MXF clips).
[Full Control User]
Can access all 3 Browser Remote screens: [Advanced Control], [Basic Control] and
[Metadata Input].
[Camera Control User] Can access only the [Advanced Control] screen. This would be the main operator
controlling the camcorder.
[Meta Control User]
Can access only the [Metadata Input] screen. This would be the person in charge of
keeping the MXF clip information up to date.
Browser Remote: Controlling the Camcorder from a Network Device
1 Open the [Users Settings] submenu.
[w Other Functions] > [Network Settings] > [Remote Settings] >
[Users Settings]
[w Other Functions]
2 To enter the [User Name] for the [Full Control User], select [Input]
and then press SET.
[Network Settings]
3 Enter the [Password] for the [Full Control User] in the same way.
4 Repeat steps 2 and 3 to enter the user names and passwords for
the [Camera Control User] and [Meta Control User].
[Remote Settings]
[Users Settings]
5 Select [OK] and then press SET to save the network
configuration. When the confirmation screen appears, press SET.
6 Back in the [Remote Settings] submenu, select [Select User] and then press SET.
7 Select [One User (Full Control)] or [Two Users (Camera/Meta)] and then press SET.
8 Select [OK] and then press SET to save the network configuration. When the confirmation screen
appears, press SET.
Starting Browser Remote
Y
P
O
After connecting the camcorder to the network, you can start the Browser Remote application on the Web
browser* of any network device connected to the same network. You can check the Browser Remote settings
on the status screens (A 216).
C
* A Web browser that supports JavaScript and is enabled to accept cookies is required.
Preparations on the camcorder
Operating modes:
1 Connect the camcorder to the desired network (A 180).
• Select a Camera Access Point connection or a wired network
connection.
[w Other Functions]
[Network Functions]
[Off]
2 To activate Browser Remote on the camcorder, open the
[Network Functions] submenu.
[w Other Functions] > [Network Functions]
3 Select [Browser Remote] and then press SET.
•
will appear on the top of the screen, next to the connection type icon. When the icons turn white, the
camcorder is ready to accept commands from the Browser Remote application.
• With Camera Access Point connections, you need to actively connect the Wi-Fi enabled device to the
camcorder.
4 Check the camcorder’s IP address on the status screen.
• Set an assignable button to [Status] in advance (A 129). Press the assignable button to open the status
screens and push the joystick up/down to select the [Network Settings 4/10] status screen.
• Check the IP address assigned to the camcorder ([IP Address]) and, if necessary, write it down.
• Press the assignable button set to [Status] again to close the status screens
English
• Enter the desired user name using the keyboard screen (A 176).
183
Browser Remote: Controlling the Camcorder from a Network Device
On the connected network device
1 Start the Web browser on the network device.
2 Enter the camcorder’s URL.
184
• Enter the IP address you checked previously into the Web browser’s
address bar, adding the prefix “http://”.
• If the you chose a port other than the default port [80], you can
specify it by adding “:nnn” at the end of the URL. For example
“http://192.168.0.80:095”.
Camcorder’s IP address from the
status screen
3 Enter the user name and password.
• Be sure to log in with the user name and password of one of the
users that were set on the camcorder (A 182). If necessary,
consult the administrator who configured the camcorder’s settings.
• The Browser Remote screen will appear. The screen displayed will
differ depending on the user information used to log in.
Example of the login screen. The screen may
• While Browser Remote is correctly connected to the camcorder, the
differ depending on the Web browser and
version used.
above the time code will turn on one by one and then turn
off in an endless loop.
• The camcorder’s ID will appear on the Browser Remote screen
while live view is not activated. In the [Metadata Input] screen, it appears at the bottom of the screen.
Y
P
O
Screen selection tabs appear only for [Full Control User]
Language selection
C
Network connection
indicator
Camcorder ID
4 Select the language for Browser Remote.
• Press the [Î] next to the language button and select the desired language from the
list. Most buttons and controls emulate physical controls on the camcorder and are
labeled in English only, regardless of the language selected.
5 Use the Browser Remote controls to operate the camcorder.
• Descriptions of the controls are given in the following pages. Detailed operation is
given in each function’s reference page.
6 When you have finished using Browser Remote, on the camcorder set
[w Other Functions] > [Network Functions] to [Off] and the press SET.
• The network icons will turn yellow and then disappear from the camcorder’s screen
and the connection with the application will be terminated.
Browser Remote: Controlling the Camcorder from a Network Device
NOTES
• Depending on the network used and the strength of the Wi-Fi signal (for Wi-Fi connections), you may notice
delays in the refreshing of the live view image and other settings.
• While color bars are displayed on the camcorder, the live view image will not be displayed.
English
The [Advanced Control] Screen
* [Full Control User]/[Camera Control User] only.
When using a computer, tablet and other devices with larger screens, the [Advanced Control] screen offers all
the controls available for operating the camcorder remotely via Browser Remote. For details, refer to each
function’s explanation.
6
7
8 9 10 11 12
13
14
1
2
3
4
5
C
Y
P
O
23
1
2
3
4
5
6
7
8
9
10
11
12
13
14
185
Live view screen* (A 50)
Current functions of assignable buttons 1 to 4*
(A 129)
Focus controls (A 81)
Assignable buttons 1 and 2 (A 130)
IRIS (ND) -/+ buttons (A 65)
Browser Remote screen selection tabs
([Full Control User] only)
Language selection (A 184)
Focus mode button (A 81, 83)
Double slot recording* (A 42)
Recording operation (A 52)
Network connection indicator*
Time code* (A 90)
Key lock button (Browser Remote controls only)
Approximate remaining battery charge*
24
25
15
16
17
18
19
20
21
22
26
15 Recording media selection and approximate
remaining recording time
16 Full auto mode/Infrared mode indicator* (A 49,
126)
17 SLOT SELECT (CF card slot selection) button
(A 41)
18 ND filter buttons (A 67)
19 White balance controls (A 69)
20 Aperture controls (A 65)
21 Shutter speed controls (A 58)
22 Gain controls (A 62)
23 Zoom controls (A 79)
24 Assignable buttons 3 and 4 (A 130)
25 START/STOP button (A 50)
26 LIVE VIEW ON/OFF button (A 50)
* Onscreen display/indication only. The content or value cannot be changed using Browser Remote.
Browser Remote: Controlling the Camcorder from a Network Device
The [Basic Control] Screen
* [Full Control User] only.
186
When using a smartphone or other device with a smaller screen, you can use the [Basic Control] screen that
offers only the most important shooting controls (START/STOP, live view, zoom and assignable buttons) but will
fit in the screen without scrolling. For details, refer to each function's explanation.
1 Open the [Basic Control] screen.
From the [Advanced Control] screen press the [Basic Control] tab.
The [Metadata Input] Screen
* [Full Control User]/[Meta Control User] only.
C
Y
P
O
Using Browser Remote you can create, edit and transfer to the camcorder a metadata profile that can be used
to record MXF clips. This metadata profile includes the user memo information (clip title, creator, location and
description), as well as GPS information. For details, refer to Using Metadata (A 111).
1 Open the [Metadata Input] screen.
• From the [Advanced Control] screen press the [Metadata Input] tab.
• This step is not necessary when logging in with the user name and
password of the [Meta Control User].
Browser Remote: Controlling the Camcorder from a Network Device
6
5
7
8
9
1
2
10
187
11
English
3
4
12
1
2
3
4
5
[
Activate] button (activate metadata control
from Browser Remote)
Metadata transfer mode selection buttons
User memo fields
GPS information fields
Browser Remote screen selection tabs ([Full
Control User] only)
6
7
8
9
10
11
12
Language selection
Recording operation
Network connection indicator*
Key lock button (Browser Remote controls only)
Approximate remaining battery charge*
[Clear] buttons (clear current data)
Camcorder ID*
Y
P
O
* Onscreen display/indication only. The content or value cannot be changed using Browser Remote.
C
NOTES
• Using Browser Remote ([
Activate] button) you can give priority to metadata sent through the application.
However, you cannot return the priority back to the SD card. To use a user memo file saved on the SD card
you will need to set [w Other Functions] > [MXF] > [Set Metadata] > [Setting] to [SD Card] on the
camcorder itself.
Real-Time Proxy Transfer
Real-Time Proxy Transfer
188
You can stream a proxy video file* of the image recorded on the camcorder to a connected iOS or Android
device** in order to record it locally on the device. You can then send the video back to a studio or broadcast
control unit for immediate reporting from the ground.
In addition to checking the camcorder’s live image, with the CameraAccess plus app you can also zoom and
start/stop recording (on the iOS/Android device or on the camcorder).
* 1.5 Mbps, 640x360 MP4 video file.
** The CameraAccess plus app needs to be installed on the iOS or Android device. The CameraAccess plus app, provided by
PIXELA, is available for free from the App Store (for iOS devices) and Google Play™ (for Android devices).
Operating modes:
1 On the iOS/Android device, download and install the CameraAccess plus app.
• The app can be downloaded for free from the following Web sites.
App Store:
http://appstore.com/cameraaccessplus
Google Play™:
http://play.google.com/store/apps/details?id=jp.co.pixela.cameraaccessplus
• This step is necessary only the first time you use this function.
Y
P
O
2 Select a Camera Access Point connection (A 180).
3 To start the Real-Time Proxy Transfer mode on the camcorder,
open the [Network Functions] submenu.
[w Other Functions] > [Network Functions]
C
4 Select [RT Proxy Transfer] and then press SET.
• [Connected] will appear on the camcorder's screen.
• While the camcorder is in Real-Time Proxy Transfer mode, only the
Q switch, CANCEL button and the joystick’s SET button can
be used on the camcorder.
[w Other Functions]
[Network Functions]
[Off]
5 On the iOS/Android device's Wi-Fi settings, select the camcorder's access point (A 180).
6 Start the CameraAccess plus app on the iOS/Android device.
7 Touch Start under Monitor from Home.
• Use the app's onscreen controls to operate the camcorder while viewing the live image on the device.
8 When you have finished recording, press SET on the camcorder to end the Real-Time Proxy Transfer
mode.
NOTES
• In real-time proxy transfer mode, the camcorder switches to full auto mode. Additionally, the focus mode
changes to autofocus (with no face detection), the zoom mode changes to [Normal] (optical zoom only) and
pre-recording is activated automatically.
• Real-time proxy transfer cannot be used when the frame rate is set to 23.98P or together with special
recording modes.
• While commands are being sent from the iOS/Android device to the camcorder, you may notice brief stops in
the live view image displayed on the iOS/Android device.
• For details about the CameraAccess plus app, visit PIXELA’s Web site.
http://pixela.jp/cecap
FTP File Transfer
FTP File Transfer
Operating modes:
Preparations
Before you can transfer clips to a connected device, you need to configure the FTP server settings and other
settings related to the handling of folders and files.
FTP Server Settings
To complete this procedure you will need detailed information about the FTP server that will be used as the
destination when transferring clips. If necessary, consult the network administrator in charge of the FTP server.
1 Open the [FTP Server Settings] submenu.
Y
P
O
[w Other Functions] > [Network Settings] > [FTP Server Settings]
2 To enter the [FTP Server], select [Input] and then press SET.
• Enter the FTP server’s IP address or host name using the keyboard
screen (A 176).
• Though the FTP server’s host name is not required when using
Camera Access Point connections, enter any characters to be able to
continue the procedure.
C
[w Other Functions]
[Network Settings]
[FTP Server Settings]
3 Enter the [User Name], [Password], and [Destination Folder] in the same way.
4 To enter the [Port No.], select [Input] and then press SET.
• Push the joystick up/down to select a value for the first digit and then press SET to move to the next digit.
• After completing all the digits, select [Set] and then press SET.
5 Select [OK] and then press SET to confirm the port number.
6 Select whether to turn the passive mode [On] or [Off] and then press SET.
• [Off] is the standard setting for most cases. [On] (passive mode) is more appropriate for FTP transfers within
a network behind a firewall.
7 Select [OK] and then press SET to save the FTP server configuration.
8 When the confirmation screen appears, press SET.
189
English
After connecting the camcorder to a network, you can transfer clips from the camcorder to another device
connected to the network using the FTP protocol. In
mode, you can transfer the last MP4 clip just
recorded. In
mode, you can transfer multiple clips or photos stored in the recording media in the
camcorder.
The following explanations assume that the FTP server is on, ready and correctly configured.
FTP File Transfer
FTP Transfer Settings
These settings determine the handling of files and folders on the FTP
server.
190
[w Other Functions]
[Network Settings]
1 Open the [Create Folder by Date] submenu.
[w Other Functions] > [Network Settings] > [FTP Transfer Settings]
> [Create Folder by Date]
2 Select the desired option and then press SET.
3 Back in the [FTP Transfer Settings] submenu, select [Same
Named Files] and then press SET.
[FTP Transfer Settings]
[Create Folder by Date]
[On]
4 Select the desired option and then press SET.
[w Other Functions]
[Network Settings]
[FTP Transfer Settings]
Options
[On]:
[Off]:
[Skip]:
[Overwrite]:
Y
P
O
[Same Named Files]
[Skip]
A new subfolder under the transfer destination folder “YYYYMMDD\HHMMSS” will be created for every
transfer operation.
All the files will be transferred to the folder set as [Destination Folder] in the FTP server settings.
C
If a file with the same name already exists in the destination folder, the file will not be transferred.
Even if a file with the same name already exists in the destination folder, the file will be transferred,
overwriting any file with the same name in the destination folder.
FTP Transfer in
Mode
If you activate the FTP transfer function and set in advance an assignable button to [MP4 FTP Transfer], you can
press the button to add the last MP4 clip recorded to the FTP transfer queue (up to 5 clips). MP4 clips are then
transferred to the FTP server one by one. The FTP transfer is performed in the background so you can continue
recording while the files are transferred. In fact, the transfer will not be interrupted even if you set the camcorder
to
mode.
You can check the FTP-related settings on the status screens (A 217).
Operating modes:
1 Set an assignable button to [MP4 FTP Transfer] in advance (A 129).
2 Connect the camcorder to the desired network (A 180).
FTP File Transfer
3 To activate the FTP transfer function, open the [Network
Functions] submenu.
[w Other Functions]
[w Other Functions] > [Network Functions]
[Network Functions]
4 Select [FTP Transfer] and then press SET.
•
5 After recording an MP4 clip, press the assignable button set to [MP4 FTP Transfer].
• The MP4 clip just recorded will be added to the FTP transfer queue.
• The number of MP4 clips in the FTP transfer queue will appear next to the
icon.
6 When you have finished transferring the desired clips, turn off the network functions.
• Set [w Other Functions] > [Network Functions] to [Off] and then press SET.
• The network icons will turn yellow and then disappear from the screen.
FTP Transfer in
Mode
Y
P
O
In
mode, you can transfer to the FTP server MXF clips recorded on the CF card and MP4 clips or photos
recorded on the SD card.
You can check the FTP-related settings on the status screens (A 217).
Operating modes:
C
Transferring a Single Clip or Photo
1 Connect the camcorder to the desired network (A 180).
• With Camera Access Point connections, you need to actively connect the Wi-Fi enabled device to the
camcorder.
2 Select the desired clip or photo and then press SET to open the clip/photo menu.
3 Select [FTP Transfer] and then press SET.
4 Select [OK] and then press SET.
• Select [Cancel] instead to cancel the operation.
•
will appear on the top of the screen, next to the connection type icon. When the icons turn white, the
clip/photo will be transferred to the FTP server. When using a LAN connection, the LAN access indicator will
flash quickly while the file is being transferred.
• While the clip/photo is being transferred, you can press SET to cancel.
• When the transfer is completed, the network icons will turn yellow and then disappear from the screen.
5 When the confirmation message appears, press SET.
191
English
will appear on the top of the screen, next to the connection type
[Off]
icon. When the icons turn white, the camcorder is ready to transfer
files.
• With Camera Access Point connections, you need to actively connect the Wi-Fi enabled device to the
camcorder.
FTP File Transfer
Transferring Multiple Clips or Photos
1 Connect the camcorder to the desired network (A 180).
192
• With Camera Access Point connections, you need to actively
connect the Wi-Fi enabled device to the camcorder.
2 Open the index screen that contains the clips or photos you want
to transfer (A 146).
[w Other Functions]
[Clips]
[Photos]
[FTP Transfer]
3 Open the [FTP Transfer] submenu.
[w Other Functions] > [Clips] or [Photos] > [FTP Transfer]
4 Select [Select] to select which clips/photos to transfer, or [All] to transfer all the clips/photos and
then press SET.
• If you selected [Select], use the joystick to move between the clips/photos. Press SET to select a clip/photo
to transfer and repeat as necessary. After selecting all the desired clips/photos, press the MENU button.
5 Select [OK] and then press SET.
•
will appear on the top of the screen, next to the connection type icon. When the icons turn white, all the
applicable clips/photos will be transferred to the FTP server. When using a LAN connection, the LAN access
indicator will flash quickly while the files are being transferred.
• Select [Cancel] instead to cancel the operation.
• While the clips/photos are transferred, you can press SET to cancel.
• When the transfer is completed, the network icons will turn yellow and then disappear from the screen.
Y
P
O
6 When the confirmation message appears, press SET.
IMPORTANT
• Observe the following precautions when transferring files. Failing to do so may interrupt the transfer and
incomplete files may remain at the transfer destination.
- Do not open the CF card slot cover or SD card slot cover.
- Do not disconnect the power source or turn off the camcorder.
• If incomplete files remain at the transfer destination, check the content and make sure they are safe to delete
before deleting them.
C
NOTES
• Depending on the access point’s settings and capabilities, it may take some time to transfer files.
Playback via Browser
Playback via Browser
You can use the Playback via Browser function to access the MP4 clips and photos in the camcorder from the
Web browser of a connected network device*. You can then play back your recordings using the Web browser
and even save local copies of them on the device.
Operating modes:
1 Open the [MP4] or [Photos] index screen (A 145).
2 Connect the camcorder to the desired network (A 180).
• Select a Camera Access Point connection or a wired network connection.
3 Open the [Playback via Browser] submenu and then press SET to
activate the function.
[w Other Functions]
[w Other Functions] > [Playback via Browser]
[Playback via Browser]
• [Connected] and the camcorder’s URL will appear on the
camcorder's screen.
• While the camcorder is in Playback via Browser mode, only the Q switch, CANCEL button and the
joystick’s SET button can be used on the camcorder.
• With Camera Access Point connections, you need to actively connect the Wi-Fi enabled device to the
camcorder.
Y
P
O
4 Connected device: Start the Web browser and enter the URL
displayed on the camcorder’s screen.
C
• The Playback via Browser screen will appear.
5 Connected device: Play back your recordings.
• To change the index screen displayed, touch/click the button on the top left of the screen (8¸ or
8}). Touch/click ¸ to show MP4 clips or } to show photos.
• Touch/click the desired recording from the list of recordings. For MP4 clips, touch/click Ð to play back the
clip. For photos, the photo will be displayed.
• Touch/click ö to return to the list of recordings.
• Devices other than iOS devices: Touch/click õ to save a local copy of the MP4 clip/photo on the device.
6 Camcorder: When you have finished playing back, press SET to end the Playback via Browser
mode.
NOTES
• Only one device may be connected to the camcorder at a time.
• Long recordings, whose video stream file exceeds 4 GB, will be recognized as multiple files on other devices.
193
English
* Depending on the device, OS, browser and video quality, you may not be able to play back or save recordings. For details, visit
your local Canon Web site.
Playback via Browser
194
C
Y
P
O
8
Photos
195
Taking Photos
* At 1920x1080 size, the camcorder can save approximately 670 photos on a 1 GB SD card.
Taking Photos in
Mode
You can take a photo while the camcorder is recording a clip or is in record pause mode. To take a photo, set an
assignable button to [Photo] in advance or use the supplied wireless controller.
Operating modes:
Y
P
O
1 Set an assignable button to [Photo] (A 129).
2 Press the assignable button to take a photo.
• You can also press the PHOTO button on the supplied wireless controller.
•
and the number of available photos appear on the upper right of the screen.
• The SD card access indicator will illuminate as the photo is being recorded.
Capturing Photos in
C
Mode
You can capture a photo from a clip during playback pause. To capture a photo, set an assignable button to
[Photo] in advance or use the supplied wireless controller.
Operating modes:
1 Set an assignable button to [Photo] (A 129).
2 Select the desired clip and then press the Ò button to start playback.
3 Pause the playback at the point you want to capture.
4 Press the assignable button to capture a photo.
• You can also press the PHOTO button on the supplied wireless controller.
•
and the number of available photos appear on the upper right of the screen.
• The SD card access indicator will illuminate as the photo is being recorded.
5 Press the Ñ button to stop playback.
English
You can take photos when the camcorder is in
mode or you can capture a photo from a clip when the
camcorder is in
mode. Photos are saved onto the SD card. In
mode, photo size is 1920x1080*. In
mode, the photo size depends on the current video configuration. If the resolution is 1920x1080 or
1440x1080, the photo size is 1920x1080; if it is 1280x720, the photo size is also 1280x720.
Taking Photos
196
IMPORTANT
• Observe the following precautions while the SD card access indicator is on or flashing. Failure to do so may
result in permanent data loss.
- Do not disconnect the power source or turn off the camcorder.
- Do not remove the SD card.
NOTES
• If the LOCK switch on the SD card is set to prevent writing, you will not be able to record a photo. Change the
position of the LOCK switch in advance.
C
Y
P
O
Photo Playback
Photo Playback
You can view the photos that you took with the camcorder.
197
Operating modes:
English
Displaying the [Photos] Index Screen
Display the [Photos] index screen to view photos.
1 Hold down the button on the Q switch and slide
the switch to MEDIA.
• The camcorder switches to
clip index screen appears.
mode and the MXF
2 Press the INDEX button.
• The index screen selection menu appears.
3 Select [Photo Index] and then press SET.
Y
P
O
• The [Photos] index screen appears.
• After you are finished viewing photos, press the INDEX
button to return to the MXF clip index screen.
Viewing Photos
C
1 Move the orange selection frame to the desired photo.
2 Press the Ò button to view the photo.
• The photo playback screen appears and the selected
photo is displayed.
• Use the Ú/Ù buttons or push the joystick left/right
to switch to the previous/next photo.
• Press the DISP. button to hide/show the onscreen
displays.
• Press the Ñ button to return to the [Photos] index
screen.
IMPORTANT
• Observe the following precautions while the SD card access indicator is on or flashing. Failure to do so may
result in permanent data loss.
- Do not disconnect the power source or turn off the camcorder.
- Do not remove the SD card.
NOTES
• The following photos may not be displayed correctly.
- Photos not recorded with this camcorder.
- Photos created or edited on a computer.
- Photos whose file names have been changed.
Deleting Photos
Deleting Photos
You can delete a photo you no longer need. Photos can be deleted one at a time from the photo playback
screen or [Photos] index screen.
198
Operating modes:
Deleting a Photo from the Playback Screen
1 Display the photo to be deleted (A 197).
2 Press SET to open the photo menu.
3 Select [Delete] and then press SET.
• The screen prompts you to confirm the operation.
4 Select [OK] and then press SET.
• Select [Cancel] instead to cancel the operation.
• The selected photo is deleted.
5 When the confirmation message appears, press SET.
Deleting a Photo from the Index Screen
1 Open the [Photos] Index Screen (A 197).
Y
P
O
2 Move the orange selection frame to the photo to be deleted.
3 Press SET to open the photo menu.
4 Select [Delete] and then press SET.
• The screen prompts you to confirm the operation.
C
5 Select [OK] and then press SET.
• Select [Cancel] instead to cancel the operation.
• The selected photo is deleted.
6 When the confirmation message appears, press SET.
Deleting Multiple Photos
1 Open the [Delete] submenu.
[w Other Functions] > [Photos] > [Delete]
2 Select [Select] to select which photos to delete or [All] to delete all the
photos, and then press SET.
• If you selected [Select], use the joystick to move between the photos.
Press SET to select a photo to delete and repeat as necessary. After
selecting all the desired photos, press the MENU button.
3 Select [OK] and then press SET.
• All the applicable photos on the SD card will be deleted.
• Select [Cancel] instead to cancel the operation.
• While the photos are being deleted, you can press SET to cancel.
4 When the confirmation message appears, press SET.
IMPORTANT
• Be careful when deleting photos. Deleted photos cannot be recovered.
[w Other Functions]
[Photos]
[Delete]
9
Additional Information
199
Menu Options
To skip directly to the page of a specific menu:
[~ Camera Setup] menu
[¡ Audio Setup] menu
[¢ Video Setup] menu
[£ OLED/VF Setup] menu
[¤ TC/UB Setup] menu
[w Other Functions] menu
[¥ My Menu] customized menu
[~ Camera Setup] menu (
mode only)
Menu item
Submenus
[Light Metering]
[AE Shift]
[Gain]
[L]
[Mode]
[AGC Limit]
[Manual]
C
A 199
A 201
A 201
A 202
A 204
A 204
A 208
Y
P
O
Setting options
A
[Backlight], [Standard], [Spotlight]
68
[+2.0], [+1.75], [+1.5], [+1.25], [+1.0], [+0.75], [+0.5], [+0.25],
[±0], [-0.25], [-0.5], [-0.75], [-1.0], [-1.25], [-1.5], [-1.75], [-2.0]
67
[Automatic], [Manual]
[Off/27 dB], [26.00 dB] to [0.0 dB]
[Fine Tuning] (0.0 dB), [33.0 dB], [27.0 dB], [24.0 dB], [21.0 dB],
[18.0 dB], [15.0 dB], [12.0 dB], [9.0 dB], [6.0 dB], [3.0 dB], [0.0 dB],
[-3.0 dB], [-6.0 dB]
[M]
[Mode]
[Automatic], [Manual]
[AGC Limit]
[Off/27 dB], [26.00 dB] to [0.0 dB]
[Manual]
[Fine Tuning] (0.0 dB), [33.0 dB], [27.0 dB], [24.0 dB], [21.0 dB],
[18.0 dB], [15.0 dB], [12.0 dB], [9.0 dB], [6.0 dB], [3.0 dB], [0.0 dB],
[-3.0 dB], [-6.0 dB]
[Mode]
[Automatic], [Manual]
[AGC Limit]
[Off/27 dB], [26.00 dB] to [0.0 dB]
[Manual]
[Fine Tuning] (0.0 dB), [33.0 dB], [27.0 dB], [24.0 dB], [21.0 dB],
[18.0 dB], [15.0 dB], [12.0 dB], [9.0 dB], [6.0 dB], [3.0 dB], [0.0 dB],
[-3.0 dB], [-6.0 dB]
62
[H]
[Shutter]
[ND Filter]
[Mode]
[Automatic], [Manual]
[Manual]
[Speed], [Angle], [Clear Scan], [Slow]
[Shutter Increment]
[Normal], [Fine]
[Automatic], [Off]
58
67
English
For details about how to select an item, refer to Using the Menus (A 29). For details about each function, see
the reference page. Menu items without a reference page are explained after the tables. Setting options in
boldface indicate default values.
Depending on the camcorder's operating mode and the current selection of other settings, some menu items
may not appear at all or may appear grayed out in the menu screens.
Menu Options
Menu item
[White Balance]
Submenus
Setting options
[B]
[AWB], [Set]
[A]
[AWB], [Set]
[PRESET]
200
[AF Mode]
69
[Mode]
[AWB], [Preset]
[Preset]
[Daylight], [Tungsten], [Kelvin]
[Speed]
[High], [Medium], [Normal]
81
[Face AF]
[Face Priority], [Face Only], [Off]
85
[On], [Off]
86
[Focus Limit]
[OIS Functions]
[Select]
[Img Stab.], [Off]
[Image Stabilizer]
[Dynamic], [Standard]
[Wide-End Angle]
[Zoom]
[Wider], [Normal]
[Mode]
[Tele-converter 6.0x], [Tele-converter 3.0x], [Tele-converter 1.5x],
[Digital Zoom], [Normal]
[Speed Level]
[Fast], [Normal], [Slow]
[Soft Zoom Control]
[Both], [Stop], [Start], [Off]
[Grip Rocker]
[Select]
[Handle Rocker H]
[Flicker Reduction]
[Conversion Lens]
[Enable]
[Type]
[Infrared]
[Custom Picture]
[Monochrome]
74
74
1 to 16 (8)
1 to 16 (8)
[Wireless Controller]
[Focal Length]
87
1 to 16 (16)
[Handle Rocker L]
[High-Speed Zoom]
Y
P
O
[Constant], [Variable]
[Constant Speed]
[Color Bars]
A
C
1 to 16 (8)
[On], [Off]
[Set to 0], [Off]
128
[Automatic], [Off]
61
[TL-H58], [WA-H58], [Off]
80
[On], [Off]
[SMPTE], [ARIB]
107
[White], [Green]
[Light]
[Toggle], [Always On], [Always Off]
[Slow Shutter]
[On], [Off]
126
[- /Select File]
–
132
[, /Edit File]
See the explanations on the reference page.
133,
135
[+ /Transfer File]
For custom picture files in the camcorder:
[Copy To
], [Load From
]
For custom picture files on the SD card:
[Copy To Cam.], [Load From Cam.]
134
Menu Options
[¡ Audio Setup] menu
Menu item
[Audio Input]
Submenus
[Automatic], [Manual]
[CH3/CH4 Level]
0 to 99 (50)
[MP4 Channels]
[CH1/CH2], [CH3/CH4]
100
[CH2 Input]
[INPUT 2], [INPUT 1]
103
[INPUT 1 Mic Trimming]
[+12 dB], [+6 dB], [0 dB], [-6 dB], [-12 dB]
104
[INPUT 1 Mic Att.]
[On], [Off]
104
[INPUT 2 Mic Trimming]
[+12 dB], [+6 dB], [0 dB], [-6 dB], [-12 dB]
104
[INPUT 2 Mic Att.]
[On], [Off]
104
[INPUT 1&2 ALC Link]
[Linked], [Separated]
105
[INPUT 1&2 Limiter]
[On], [Off]
106
[MIC Att.]
[On], [Off]
[MIC Low Cut]
[On], [Off]
[Int. Mic Att.]
[On], [Off]
[Int. Mic Low Cut]
[Off], [LC1], [LC2]
[Monitor Delay]
[Monitor Channels]
[HDMI Channels]
[Level]
C
[Headphone Volume]
[Speaker Volume]
100
106
101
Y
P
O
[Normal], [High]
[-12 dB], [-18 dB], [-20 dB], [Off]
107
[Line Out], [Normal]
167
[CH1/CH2], [CH1/CH1], [CH2/CH2], [CH1+2/CH1+2], [CH3/CH4],
[CH3/CH3], [CH4/CH4], [CH3+4/CH3+4], [CH1+3/CH2+4]
166
[CH1/CH2], [CH3/CH4]
[1 Vrms], [2 Vrms]
[Off], 1 to 15 (8)
[Off], 1 to 15 (8)
167
149
mode, not available in some index screens and playback modes.
[¢ Video Setup] menu
Menu item
Submenus
Setting options
In
In
[3G-SDI Mapping]
[Level A], [Level B]
[MON.]
[HD], [SD], [Off]
163
[Normal], [+1920x1080 59.94P]
164
[HDMI]
[HD/SD Output]
[HD Onscreen Displays]
[On], [Off]
[SD Onscreen Displays]
[On], [Off]
[Resize SD Output]
mode: [Direct], [Compatible], [Off]
mode: [On], [Off]
A
[3G/HD-SDI]*
163
165
[Letterbox], [Squeeze], [Side Crop]
165
[Rec Command]
[On], [Off]
49
[HDMI Time Code]
* In
[On], [Off]
96
[GENLOCK/SYNC OUT]
[Genlock], [SYNC Output]
94,
96
[SYNC Scan Mode]
[P], [PsF]
96
mode, not available in some index screens and playback modes.
201
English
[CH3/CH4 Mode]
[1 kHz Tone]
* In
A
[On], [Off]
[Int. Mic Sensitivity]
[Audio Output]*
Setting options
[4-Channel Input]
Menu Options
[£ OLED/VF Setup] menu
Menu item
[OLED Setup]
202
Submenus
Setting options
[Brightness]
-99 to 99 (±0)
[Contrast]
-99 to 99 (±0)
[Color]
-20 to 20 (±0)
[Sharpness]
1 to 4 (2)
[Luminence]
[On], [Off]
A
34
[Color Balance]
[Viewfinder Setup]
[R-B Simult. Adjust.]
-25 to 25 (±0)
[R Fine Tuning]
-25 to 25 (±0)
[B Fine Tuning]
-25 to 25 (±0)
[Brightness]
-99 to 99 (±0)
[Contrast]
-99 to 99 (±0)
[Color]
-20 to 20 (±0)
[Sharpness]
1 to 4 (2)
[Backlight]
[Normal], [Bright]
[OLED Mirror Image]
[OLED/VF B&W]
[OLED/VF Simul.]
[Audio Level]*
[Display Metadata]*
[Date/Time]
[Peaking]
[Setting]
[Select]
[Peaking 1]
[Color]
[Gain]
[Frequency]
[On], [Off]
33
[On], [Off]
35
[On], [Off]
34
[On], [Off]
–
Y
P
O
[On], [Off]
[Camera Data]
[On], [Off]
C
34
–
[On], [Off]
[Peaking 1], [Peaking 2]
[White], [Red], [Yellow], [Blue]
[Off], 1 to 15 (8)
1 to 4 (2)
84
[Peaking 2]
[Zebra]
[Markers]
[Color]
[White], [Red], [Yellow], [Blue]
[Gain]
[Off], 1 to 15 (15)
[Frequency]
1 to 4 (1)
[Setting]
[On], [Off]
[Select]
[Zebra 1], [Zebra 2], [Zebra 1&2]
[Zebra 1 Level]
[70 ±5%], [75 ±5%], [80 ±5%], [85 ±5%], [90 ±5%], [95 ±5%]
[Zebra 2 Level]
[70%], [75%], [80%], [85%], [90%], [95%], [100%]
[HD Output]
[On], [Off]
[Enable]
[On], [Off]
[Center]
[Black], [Gray], [Off]
[Horizontal]
[Black], [Gray], [Off]
[Grid]
[Black], [Gray], [Off]
[Safe Area]
[Black], [Gray], [Off]
[Safe Area Setting]
[80%], [90%], [92.5%], [95%]
[Aspect Marker]
[Black], [Gray], [Off]
[Aspect Ratio]
[4:3], [13:9], [14:9], [1.66:1], [1.75:1], [1.85:1], [2.35:1]
89
88
Menu Options
Menu item
[Custom Display 1]
Submenus
[Light Metering]
[On], [Off]
[Custom Picture]
[On], [Off]
[ND Filter]
[On], [Off]
[Focus Mode]
[On], [Off]
[Object Distance]
[Always On], [Normal], [Off]
[Full Auto]
[On], [Off]
[Infrared]
[On], [Off]
[White Balance]
[On], [Off]
[Exposure]
[On], [Off]
[Iris]
[On], [Off]
[Gain]
[On], [Off]
[Shutter]
[On], [Off]
[Conversion Lens]
[On], [Off]
[Tele-converter]
[On], [Off]
[Peaking]
[On], [Off]
[On], [Off]
[Remaining Battery]
[Remaining Rec Time]
[Recording Mode]
[Interval Counter]
C
[Remaining Photos]
* In
[Only Warnings], [Normal], [Off]
[Only Warnings], [Normal], [Off]
[On], [Off]
[Genlock]
[Time Code]
Y
P
O
[On], [Off]
[OIS Functions]
[On], [Off]
[On], [Off]
[On], [Off]
[Only Warnings], [Normal], [Off]
[Temperature/Fan]
[On], [Off]
[Movie Format]
[On], [Off]
[Bit Rate/Resolution]
[On], [Off]
[Frame Rate]
[On], [Off]
[OSD Recording]
[On], [Off]
[Wireless Controller]
[On], [Off]
[Output Display]
[On], [Off]
[Rec Command]
[On], [Off]
[User Memo]
[On], [Off]
[User Bit]
[On], [Off]
[Monitor Channels]
[On], [Off]
[Audio Level]
[On], [Off]
[4-Channel Input]
[On], [Off]
[Network Functions]
[On], [Off]
[GPS]
[On], [Off]
[Date/Time]
[Date/Time], [Time], [Date], [Off]
mode, not available in some index screens and playback modes.
[Audio Level] (
mode only): Displays the audio level meter during playback mode when set to [On].
A
51,
142
203
English
[Always On], [Normal], [Off]
[Magnification]
[Custom Display 2]
Setting options
[Zoom Position]
Menu Options
[Display Metadata] (
mode only): Displays the date and time of recording and/or the camera data (shutter
speed, aperture value, gain) during the playback of MXF clips. During the playback of MP4 clips, when [Date/
Time] is set to [On] only the date of recording is displayed. During photo playback, the date and time of recording
is always displayed (this setting is not available).
204
[¤ TC/UB Setup] menu (
mode only)
Menu item
[Time Code]
Submenu
Setting options
A
[Mode]
[Preset], [Regen.]
90
[Run]
[Rec Run], [Free Run]
90
[DF/NDF]*
[DF], [NDF]
91
[Setting]
[Set], [Reset]
90
[TC In/Out]
[In], [Out]
95
[XF Legacy Sync]
[On], [Off]
–
[Recording Mode]
[Internal], [External]
95
[Output Mode]
[Fixed], [Pulldown]
96
[Setting], [Time], [Date]
93
[User Bit]
[Type]
* When the frame rate is set to 23.98P, the time code is set to [NDF] and this setting cannot be changed.
Y
P
O
[XF Legacy Sync]: Determines the characteristics of the synchronization reference output signal (A 96)
and the characteristics of the time code input/output signals and the genlock reference signal when the frame
rate is set to 23.98P.
[On]: Synchronization mode compatible with older Canon XF series camcorders. When the frame rate is set
to 23.98P, synchronizes the time code at a 30-frame signal and the Genlock signal at a 29.97 Hz or 59.94 Hz
signal. A 59.94i (or 59.94P) signal is output as the synchronization reference output. Use this setting to
synchronize the camcorder with a Canon HD Camcorder XF105 or XF305.
[Off]: Standard synchronization mode. When the frame rate is set to 23.98P, synchronizes the time code at a
24-frame signal and the Genlock signal* at a 23.98 Hz signal. The synchronization reference output signal
has the same frequency as video output from 3G/HD-SDI terminal. Select this setting to synchronize the
camcorder with a Canon HD Camcorder XF205 or with one of the camcorders/digital cinema cameras in the
CINEMA EOS SYSTEM lineup.
C
* Only when [¢ Video Setup] > [3G/HD-SDI] is set to [Direct].
[w Other Functions] menu
Menu item
[Reset]
[Transfer Menu//]
Submenus
[Cancel], [OK]
[Camera Settings]
[Cancel], [OK]
[Assignable Buttons]1
[Cancel], [OK]
[Save To
[Menu], [Menu+/]
]
[Load From
[Time Zone]
[Set Clock]
Setting options
[All Settings]
]
[Menu], [Menu+/]
List of world time zones.
[UTC-05:00 New York]
[Date/Time]
–
[Date Format]
[YMD], [YMD/24H], [MDY], [MDY/24H], [DMY], [DMY/24H]
A
–
143
27
27
Menu Options
Menu item
Submenus
[Setting]
A
Setting options
[WFM], [VS], [Edge Mon.], [Off]
108
[Type]
[Line], [Line+Spot], [Field], [RGB], [YPbPr]
108
205
[Gain]
[1x], [2x]
109
English
[WFM (OLED)]1
[Waveform Monitor]
[Vectorscope]
[Type]
[Spot], [Normal]
[Gain]
[1x], [5x]
[Edge Monitor]
[Type]
[Type 1], [Type 2]
[Gain]
[Off], 1 to 15 (12)
109
[Language !]
[Deutsch], [English], [Español], [Français], [Italiano], [Polski],
[Português], [
], [
], [
], [
]
28
[REMOTE Term.]
[RC-V100], [Standard]
45
[Wireless Controller]
[On], [Off]
44
129
[Assignable Buttons]1
[1] to [13]
See footnote 2.
[Tally Lamp]
[Front]
[On], [Off]
[Rear]
[POWER LED]
[Media Access LED]
[LAN (Ethernet) LED]
[Fan]
[Genlock Adjustment]
[Movie Format]
[MXF]
C
[Bit Rate/Resolution]
[Frame Rate]
[Relay Recording]
[Double Slot Recording]
Y
P
O
–
[On], [Off]
–
[On], [Off]
–
[On], [Off]
–
[On], [Automatic]
54
-1023 to +1023 (000)
[MXF (CF)], [MXF (CF)+MP4
], [MP4
–
]
[50 Mbps 1920x1080], [50 Mbps 1280x720], [35 Mbps 1920x1080],
[35 Mbps 1440x1080], [35 Mbps 1280x720], [25 Mbps 1440x1080]
55
55
[59.94i], [59.94P], [29.97P], [23.98P]
[On], [Off]
[On], [Off]
42
[Clips]
[Title Prefix]
Two characters, each:
[A] to [Z], [0] to [9] ([AA])
[Number setting]
[Set], [Reset]
[Add / File]
[On], [Off]
–
[Set Metadata]
[Setting]
[Remote], [SD Card]
[User Memo]
[Off], list of user memo files available on the SD card
[Country Code]
Letters A to Z, numbers 0 to 9, plus sign (+), minus sign (-), colon (:),
space
[Organization]
111
–
[User Code]
[MP4]
[Bit Rate/Resolution]
When the movie format is set to MP4:
[35 Mbps 1920x1080], [24 Mbps 1920x1080],
[17 Mbps 1280x720], [9 Mbps 1280x720]
When the movie format is set to MXF+MP4:
[Linked to MXF], [3 Mbps 640x360]
[Frame Rate]
[29.97P], [23.98P]
[Rec Control]
[START/STOP Button], [Assignable Buttons]
[Start/Stop]
[Start], [Stop]
55
123
Menu Options
Menu item
Submenus
[Special Recording]
206
[Interval Recording]
[Frame Recording]
[Slow & Fast Motion]
[Clips] or [Photos]
Setting options
When the movie format is set to MXF:
[Interval Recording], [Frame Recording], [Pre-Recording],
[Slow & Fast Motion], [Off]
When the movie format is set to MP4:
[Pre-Recording], [Off]
A
118
[Interval]
[1 sec] to [10 sec], [15 sec], [20 sec],
[30 sec], [40 sec], [50 sec],
[1 min] to [10 min]
[Recorded Frames]
When the frame rate is set to 23.98P, 29.97P or 59.94i:
1, 3, 6, 9
When the frame rate is set to 59.94P:
2, 6, 12
[Recorded Frames]
When the frame rate is set to 23.98P, 29.97P or 59.94i:
1, 3, 6, 9
When the frame rate is set to 59.94P:
2, 6, 12
119
12, 15, 18, 20, 21, 22, 24, 25, 26, 27, 28, 30 (all in fps)
Only when the resolution is set to 1280x720 also:
32, 34, 36, 40, 44, 48, 54, 60 (all in fps)
120
–
154,
198
[S&F Frame Rate]
[Delete]1
[Select]
[All]
[Cancel], [OK]
[Copy]1
[Select]
[$ Mark]
[All]
[FTP Transfer]1
[Select]
[All]
[Review Recording]
Y
P
O
118
–
C
[Cancel], [OK]
153
[Cancel], [OK]
–
192
[Cancel], [OK]
[Entire Clip], [Last 4 sec]
116
[Delete Last Clip]
[Cancel], [OK]
[File Numbering]1
[Reset], [Continuous]
117
[Delete All $ Marks]
[Cancel], [OK]
153
[Custom Function]
[Reset Hour Meter]
[Shockless Gain]
[Fast], [Normal], [Slow], [Off]
[Shockless WB]
[On], [Off]
[AE Response]
[High], [Normal], [Low]
[Iris Limit]
[On], [Off]
[Iris Ring Direction]
[Reverse], [Normal]
[Focus Ring Direction]
[Reverse], [Normal]
[Zoom Ring Direction]
[Reverse], [Normal]
[Focus Ring Control]
[Fast], [Normal], [Slow]
[Zoom Ring Control]
[Fast], [Normal], [Slow]
[Focus Assistance B&W]
[Both], [Magnify], [Peaking], [Off]
[Distance Units]
[Meters],[Feet]
[Zoom Indicator]
[Bar], [Numerical]
[Scan Reverse Rec]
[Both], [Vertical], [Horizontal], [Off]
[OSD Recording]
[On
–
141
], [Off]
[Cancel], [OK]
–
Menu Options
Menu item
Submenus
A
Setting options
[Network Functions]
[FTP Transfer], [Browser Remote], [RT Proxy Transfer], [Off]
173
[Playback via Browser]1
–
193
–
174,
179
[Select]
[No.1] to [No.5]
180
[Edit]
[Settings], [Rename]
181
[Network Settings]
[Connection Settings]
[Set Up New]
207
[Camera Settings]
–
[Select User]
[One User (Full Control)], [Two Users (Camera/Meta)]
[Users Settings]
–
[FTP Server Settings]
–
[FTP Transfer Settings]
[Create Folder by Date]
[On], [Off]
[Same Named Files]
[Skip], [Overwrite]
[GPS Auto Time]3
[Initialize Media]
[On], [Off]
[CF A]
189
114
[Cancel], [OK]
[CF B]
[SD Card]
41
[Complete], [Quick]
[Certification Logos]
[Firmware]
1
2
Y
P
O
182
C
–
–
–
–
In
mode, not available in some index screens and playback modes.
Setting options for [Assignable Buttons]: [(NONE)], [Img Stab.], [POWERED IS], [Focus Limit], [Face AF], [Backlight], [Spotlight],
[Digital Zoom], [Tele-converter], [Wide-End Angle], [Gain Mode], [Shutter Mode], [Shutter Increment], [WB Mode], [PEAKING],
[ZEBRA], [WFM], [MAGN.], [TL-H58], [WA-H58], [Color Bars], [Infrared Monochrome], [Infrared Light], [Markers], [OLED Setup],
[Viewfinder Setup], [OLED/VF B&W], [Onscreen Display], [MP4 Start/Stop] (only for assignable buttons 1 to 4), [MP4 FTP
Transfer], [Add Shot Mark 1], [Add Shot Mark 2], [Add $ Mark], [Add % Mark], [Time Code], [Time Code Hold], [HEADPHONE
+], [HEADPHONE -], [Monitor Channels], [Audio Level], [Wireless Controller], [Photo], [Status], [My Menu], [Initialize Media], [User
Setting].
The default settings are as follows. [1]: [PEAKING], [2]: [ZEBRA], [3]: [POWERED IS], [4]: [MAGN.], [5] to [10]: [NONE],
[11]: [HEADPHONE +], [12]: [HEADPHONE -], [13]: [WFM].
3 Available only when the optional GP-E2 GPS Receiver is connected to the camcorder.
English
[Remote Settings]
Menu Options
208
[Reset]: Reset various camcorder settings.
[All Settings]: Resets all the camcorder’s settings to default settings, except for the hour meter.
[Camera Settings] (
mode only): Resets the white balance, iris, gain, shutter speed,
[~ Camera Setup] settings and custom picture settings to default settings.
[Assignable Buttons]: Resets the assignable buttons to default settings.
[Tally Lamp] (
mode only): Allows you to set whether the front and rear tally lamps illuminate while the
camcorder is recording.
[POWER LED]: Allows you to set whether the power indicator illuminates while the camcorder is on.
[Media Access LED]: Allows you to set whether the CF card access indicators or the SD card access indicator
illuminate while the camcorder is accessing a CF card or SD card.
[LAN (Ethernet) LED]: Allows you to set whether the LAN access indicator illuminates when the camcorder is
accessing a network via the LAN cable.
[Genlock Adjustment] (
mode only): The phase difference between the external Genlock signal and the
camcorder is initially set to 0. This function allows you to adjust it within the range of approx. ±0.4 H (-1023 to
1023). When setting to 1000 or more or -1000 or less, set the first field to 10 or -10, respectively.
[MXF] > [Clips] settings (
mode only)
[Title Prefix]: Determines the first 2 characters of the clip name. Combined with the [Number Setting] setting,
this constitutes the 6-character clip name.
Y
P
O
[Number Setting]: Determines the last 4 digits of the clip name. Combined with the [Title Prefix] setting, this
constitutes the 6-character clip name. Select [Set] to assign a desired number to the first clip you record or
select [Reset] to reset the number to [0001]. The numerals increase every time a clip is recorded.
[MXF] > [Set Metadata] settings (
mode only)
[Country Code]: This identifier is the country code defined by ISO-3166-1 and is to be entered starting from the left.
C
[Organization]: This identifier represents the organization that owns or operates the camcorder and can be
obtained by registering with the SMPTE Registration Authority. If the organization is not registered, enter [0000].
[User Code]: This identifier designates the user. Leave this blank if [Organization] is set to [0000].
[Delete Last Clip]: (
mode only): Deletes the last clip you recorded. This setting option will not appear if
you turned the camcorder off since recording the last clip.
[Reset Hour Meter]: The camcorder has two “hour meters” – the first keeps track of total operation time and the
second keeps track of operation time since the last time the second hour meter was reset with this function.
[Certification Logos] (
mode only): This setting displays certification logos that apply to this camcorder.
[Firmware] (
mode only): You can verify the current version of the camcorder’s firmware. This menu option is
usually unavailable.
[¥ My Menu] (
mode only)
Menu item
[Edit]
Submenu
Setting options
[Register]
[Cancel], [OK]
[Move]
[Cancel], [OK]
[Delete]
[Cancel], [OK]
[Reset All]
[Cancel], [OK]
A
30
Displaying the Status Screens
Displaying the Status Screens
You can use the status screens to check the camcorder’s various recording- and playback-related settings. You
can also output the status screens on an external monitor.
209
Operating modes:
English
1 Set an assignable button to [Status] in advance (A 129).
2 Press the assignable button to open the status screens.
• The status screen most recently displayed will appear unless you turned off the camcorder or changed the
operating mode. In such case, the [Camera 1/2] status screen appears in
mode and the [Assignable
Buttons 1/2] status screen appears in
mode.
3 Push the joystick up/down to scroll through the status screens.
4 When you are finished, press the assignable button set to [Status] again to exit the status screens.
• Alternatively, you can press the MENU button. Doing so will exit the status screen and open the menu.
,
Status screen
[Camera 1/2], [Camera 2/2]
A
Description
Y
P
O
Displays settings related to main recording functions, like gain, focus
and zoom.
Ü
–
210
[Assignable Buttons 1/2],
[Assignable Buttons 2/2]
Allows you to verify the current function of each assignable button.
Ü
Ü1
210
[Audio]
Displays settings related to audio.
Ü
Ü
211
[Media]
Displays information about the recording media.
Ü
Ü
211
[Video]
Displays the settings for the video terminals and which special
recording mode is in effect.
Ü
Ü
212
[Metadata 1/2], [Metadata 2/2]
Displays the user memo and other metadata that will be recorded
with clips.
Ü
–
212
[Battery/Hour Meter]
Allows you to check the remaining battery time, battery life and how
long the camcorder has been in operation.
Ü
Ü
213
[/ Data 1/3], [/ Data 2/3],
[/ Data 3/3]2
Displays the settings for the custom picture file that will be applied
and saved with MXF clips.
Ü
–
213,
214
[Network Settings 1/10] to
[Network Settings 10/10]
Displays various settings related to the camcorder's network
functions.
Ü
Ü
215217
[GPS Information Display]3
Displays GPS information.
Ü
–
217
1
2
3
C
In
mode, not available in some index screens and playback modes.
These screens appear only after a custom picture file has been selected.
This screen appears only when an optional GP-E2 GPS Receiver is connected to the camcorder.
Displaying the Status Screens
[Camera 1/2], [Camera 2/2] Status Screens (
mode only)
1
2
3
210
4
5
6
7
8
1
2
3
4
Gain values for each GAIN switch position
(A 62)
Gain limits for each GAIN switch position (A 63)
White balance settings for each WHITE BAL.
switch position (A 69)
AF mode (A 81)
C
5
6
7
Autofocus for faces (Face AF) (A 85)
Focus limit (A 86)
Zoom speed settings for the various zoom
controls (A 74)
Flicker reduction (A 61)
Y
P
O
8
[Assignable Buttons 1/2], [Assignable Buttons 2/2] Status Screen
1
1
1
Assignable buttons 1 to 13* (A 129)
* Assignable buttons 5 to 10 do not appear in
mode.
Displaying the Status Screens
[Audio] Status Screen
In
mode
1
2
211
English
3
4
In
mode
4
1
2
Number of audio channels for MXF clips (A 100)
MP4 audio channels during 4-channel audio
recording (A 100)
[Media] Status Screen
1
2
3
4
1
2
3
4
5
6
7
C
CF card A
CF card B
SD card
Speed class of the SD card
Total space on CF card A
Used space on CF card A
Available recording time on CF card A
3
Audio source input and audio level adjustment
mode for each audio channel (A 98)
Headphone volume (A 149)
Y
P
O
4
8
9
10
11
12
13
5
6
7
8
9
10
11
12
13
Approximate used space on CF card A
Total space on the SD card
Used space on the SD card
Available recording time on the SD card
Available number of shots on the SD card
Approximate used space on the SD card
NOTES
• Depending on the recording media, the total space displayed on the screen may differ from the nominal
capacity listed on the CF card or SD card.
Displaying the Status Screens
[Video] Status Screen
1
2
3
212
6
7
4
5
1
2
3
4
*
HDMI OUT terminal status
3G/HD-SDI terminal* output settings (A 163)
MON. terminal* output settings (A 163)
Special recording mode (A 118)
5
6
7
MP4 clip settings for MXF+MP4 simultaneous
recording (A 123)
Superimposing onscreen displays (A 165)
SD output setting (A 165)
only.
Y
P
O
[Metadata 1/2], [Metadata 2/2] Status Screens (
1
2
3
4
5
6
7
8
1
2
3
4
User memo file name (A 111)
Clip title
Camera operator
Filming location
C
5
6
7
8
mode only)
Clip description
Country code (A 208)
Organization code
User code
Displaying the Status Screens
[Battery/Hour Meter] Status Screen
1
213
2
English
3
4
5
1
2
3
Remaining recording time
Remaining recording time indicator
Battery life indicator
[/ Data 1/3] Status Screen (
1
2
3
4
5
6
7
8
1
2
3
4
5
4
5
Total operation time (A 208)
Operation time since using [Reset Hour Meter]
(A 208)
mode only)
C
Y
P
O
Custom picture file name (A 132) and protection
(A 133)
Gamma (A 135)
Master pedestal (A 136)
Master black RGB levels (A 136)
Black gamma settings (level, range and point)
(A 136)
6
7
8
9
9
Knee settings (slope, point and saturation)
(A 137)
Skin detail settings (hue, chroma, area and Y
level) (A 138)
Selective NR settings (hue, chroma, area and Y
level) (A 138)
Low key saturation (A 136)
Displaying the Status Screens
[/ Data 2/3] Status Screen (
mode only)
1
2
3
4
5
6
7
214
1
2
3
Sharpness settings (level, horizontal detail
frequency, horizontal/vertical detail balance, and
limit) (A 137)
Sharpness settings (knee aperture gain and
slope, ingredient ratio) (A 137)
Level depend settings (level, slope and offset)
(A 138)
[/ Data 3/3] Status Screen (
1
2
3
4
5
6
1
2
3
4
4
5
6
7
Coring settings (level, offset, curve and depth)
(A 137)
Noise reduction (A 138)
Color matrix settings (select, gain and phase)
(A 139)
Color matrix settings (A 139)
Y
P
O
mode only)
C
White balance R/B gain (A 139)
Color correction (A 139)
Area A settings (phase, chroma, area and Y level)
(A 139)
Area A revision settings (level and phase)
(A 139)
7
8
5
6
7
8
Area B settings (phase, chroma, area and Y level)
(A 139)
Area B revision settings (level and phase)
(A 139)
Setup level (A 140)
Clips exceeding 100% (A 140)
Displaying the Status Screens
[Network Settings 1/10] Status Screen
215
1
2
English
1
2
Camcorder’s MAC address for Wi-Fi networks
Camcorder’s MAC address for wired networks
[Network Settings 2/10], [Network Settings 3/10] Status Screens
1
2
3
4
5
6
C
Y
P
O
Connection settings of the current network connection (A 173)
1
2
3
Network configuration name (A 180)
Connection type
SSID (network name)
4
5
6
Authentication and encryption method
WEP index key
Wi-Fi channel
Displaying the Status Screens
[Network Settings 4/10], [Network Settings 5/10] Status Screens
216
1
2
3
4
5
6
TCP/IP settings of the current network connection (A 178)
1
2
3
4
IP address assignment method
IP address
Subnet mask
Default gateway
Y
P
O
5
6
C
Primary DNS server (assignment method/IP
address)
Secondary DNS server (assignment method/IP
address)
[Network Settings 6/10], [Network Settings 7/10] Status Screens
1
2
3
4
Browser Remote settings (A 182):
1 Port number
2 Camcorder ID
* The password itself will not be displayed.
3
4
User selection
User name and whether a password was set* for
each Browser Remote user
Displaying the Status Screens
[Network Settings 8/10] through [Network Settings 10/10] Status Screens
217
English
1
2
3
4
5
6
7
8
FTP server settings (A 189):
1 FTP server (host) name
2 User name
3 Password protection*
4 Port number
* The password itself will not be displayed.
C
Y
P
O
5
6
7
8
[GPS Information Display] Status Screen (
Destination folder on the FTP server
Passive mode
Create new folders by transfer date
Handling of same-named files
mode only)
1
2
3
4
5
GPS information (A 114)
1
2
3
Latitude
Longitude
Elevation
4
5
UTC (coordinated universal time) date and time
Satellite signal strength
Troubleshooting
Troubleshooting
If you have a problem with your camcorder, refer to this section. Consult your dealer or a Canon Service Center
if the problem persists.
218
Power source
The camcorder will not turn on or it turns off by itself.
- The battery pack is exhausted. Replace or charge the battery pack.
- Remove the battery pack and reattach it correctly.
Shortly after turning it on, the camcorder turns off on its own.
- You are using a DC coupler or a battery pack that is not compatible for use with this camcorder. Use a recommended
battery pack (A 233).
Cannot charge the battery pack.
- The temperature of the battery pack is outside the charging range. If the battery pack’s temperature is below 0 °C
(32 °F), warm it before charging it; if it is above 40 °C (104 °F), let the battery pack cool down before charging it.
- Charge the battery pack in temperatures between 0 °C and 40 °C (32 °F and 104 °F).
- The battery pack is faulty. Replace the battery pack.
The battery pack is exhausted extremely quickly even at normal temperatures.
- Check the [Battery/Hour Meter] status screen (A 213) to see whether the battery pack is at the end of its service life.
If so, buy a new battery pack.
Recording
Y
P
O
Pressing the START/STOP button will not start recording.
- The START/STOP lock lever on the handle is set to C, rendering the handle’s START/STOP button inoperable. Change
the position of the lock lever.
C
The point where the START/STOP button was pressed does not match the beginning/end of the recording.
- There is a slight interval between pressing the START/STOP button and the actual start/end of recording. This is not a
malfunction.
The camcorder will not focus.
- The camcorder may not be able to focus on certain subjects using autofocus. Focus manually (A 83).
- The viewfinder is not adjusted. Use the dioptric adjustment lever to make the proper adjustment (A 32).
- The lens or Instant AF sensor is dirty. Clean the lens or sensor with a soft lens-cleaning cloth.
When a subject flits across in front of the lens, the image appears slightly bent.
- This is a phenomenon typical of CMOS image sensors. When a subject crosses very quickly in front of the camcorder,
the image may seem slightly warped. This is not a malfunction.
Changing between recording (ÜREC/ÜMP4) and record pause (STBY/MP4) takes longer than usual.
- When the recording media contains a large number of clips, some operations may take longer than usual. Save your
clips (A 168) and initialize the recording media (A 41). Alternatively, replace the recording media.
The camcorder cannot record to the recording media properly.
- This may occur as recordings are made and deleted over time. Save your clips (A 168) and initialize the recording media
(A 41).
After using the camcorder for a long time, it becomes hot.
- The camcorder may become hot after using it continuously for long periods of time; this is not a malfunction. If the
camcorder becomes unusually hot or it becomes hot after using it only for a short while, it may indicate a problem with
the camcorder. Consult a Canon Service Center.
Troubleshooting
Playback
Cannot delete MXF clips.
- You cannot delete MXF clips with an $ mark. Remove the $ mark (A 153) to delete the clip.
Deleting clips takes longer than usual.
- When the recording media contains a large number of clips, some operations may take longer than usual. Save your
clips (A 168) and initialize the recording media (A 41).
Cannot copy MXF clips.
- There is not enough available space on the CF card being copied to or the CF card already contains the maximum
number of clips (999 clips). Delete some clips (A 154) to free some space or replace the CF card.
Indicators and Onscreen Displays
ì appears in red on the screen.
- Battery pack is exhausted. Replace or charge the battery pack.
í appears on the screen.
- The camcorder cannot communicate with the battery pack attached so the remaining battery time cannot be
displayed.
Y
P
O
The tally lamp does not illuminate.
- Set [Other Functions] > [Tally Lamp] > [Front] and/or [Rear] to [On].
The tally lamp flashes quickly.
(4 flashes per second)
- The battery pack is exhausted. Replace or charge the battery pack.
- There is not enough available space on the recording media. Delete some clips (A 154) to free some space or replace
the recording media.
- A system error has occurred. Turn off the camcorder and back on again. If this does not solve the problem, consult a
Canon Service Center.
C
The tally lamp flashes slowly.
(1 flash per second)
- The combined available space on both CF cards is low. Replace the CF card that is not being recorded onto.
- Available space on the SD card is low. Replace the SD card.
appears in red on the screen.
- An SD card error occurred. Remove and reinsert the SD card. If the display does not change back to normal, save your
MP4 clips (A 168) and photos and initialize the SD card (A 41).
Even after stopping recording, the CF card access indicator or SD card access indicator stays illuminated in red.
- The clip is being recorded. This is not a malfunction.
7 keeps flashing on the screen.
- You connected the optional GP-E2 GPS Receiver to the camcorder’s USB terminal in
GP-E2 and connect in again after setting the camcorder in
mode.
mode. Disconnect the
U keeps flashing on the screen.
- The camcorder cannot lock on the external Genlock signal being input. Check the external signal. If necessary, check
the [TC/UB Setup] > [XF Legacy Sync] setting (A 204).
Picture and Sound
The OLED screen is too dark.
- Adjust the brightness with the [OLED/VF Setup] > [OLED Setup] > [Brightness] setting. To make the screen brighter
temporarily, set [OLED/VF Setup] > [OLED Setup] > [Luminence] to [On].
Screen displays turn on and off repeatedly.
- The battery pack is exhausted. Replace or charge the battery pack.
- Remove the battery pack and reattach it correctly.
English
Cannot delete MP4 clips/photos.
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
- Photos that were protected using other devices cannot be deleted with the camcorder.
219
Troubleshooting
Abnormal characters appear on the screen and the camcorder does not operate properly.
- Disconnect the power source and reconnect it after a short time. If the problem still persists, use the [Other Functions]
> [Reset] > [All Settings] function. This resets all the camcorder’s settings to default values except for the hour
meter.
220
Video noise appears on screen.
- Keep a distance between the camcorder and devices that emit strong electromagnetic fields such as near powerful
magnets and motors, MRI machines or high-voltage power lines.
Horizontal bands appear on the screen.
- This is a phenomenon typical of CMOS image sensors when recording under some types of fluorescent, mercury or
sodium lamps. This is not a malfunction. You may be able to reduce the symptoms by setting [Camera Setup] >
[Flicker Reduction] to [Automatic] and/or by setting [Camera Setup] > [Shutter] > [Manual] to [Speed] and the
shutter speed to a value matching the frequency of the local electrical system (1/50* or 1/100 for 50 Hz systems, 1/60
or 1/120 for 60 Hz systems).
* May not be available depending on the frame rate.
Audio cannot be recorded.
- The AUDIO IN selection switch is not set correctly (A 103).
- An external microphone connected to the INPUT 1/INPUT 2 terminal requires phantom power. Set the corresponding
INPUT 1/INPUT 2 audio input selection switch to MIC+48V (A 103).
- The external microphone connected to the MIC terminal is not turned on or its battery is empty.
Audio is recorded at an extremely low level.
- The audio level for CH1 or CH2 is set to M, and the recording level is set too low. During 4-channel audio recording:
[Audio Setup] > [Audio Input] > [CH3/CH4 Mode] is set to [Manual] and [CH3/CH4 Level] is set to a level too low.
Check the audio level meter on the screen and adjust the audio level correctly (A 105, 106).
- The microphone attenuator is on. Turn off the microphone attenuator (A 102, 104).
Y
P
O
Sound is distorted or is recorded at lower levels.
- When recording near loud sounds (such as fireworks, shows or concerts), sound may become distorted or it may not
be recorded at the actual levels. Activate the microphone attenuator (A 102, 104), or adjust the audio recording level
manually.
The picture is displayed correctly but there is no sound from the built-in speaker.
- Speaker volume is turned off. Adjust the volume (A 149).
- If headphones are connected to the camcorder, disconnect them.
C
Recording Media and Accessories
Cannot insert the recording media.
- The CF card or SD card you are trying to insert is not facing the correct direction. Turn it over and insert it.
Cannot record on the CF card.
- A compatible CF card must be used (A 38).
- Initialize the CF card (A 41) when you use it with the camcorder for the first time.
- The CF card is full or it already contains the maximum number of clips (999 clips). Delete some clips (A 154) to free
some space or replace the CF card.
Cannot record on the SD card.
- A compatible SD card must be used (A 38).
- Initialize the SD card (A 41) when you use it with the camcorder for the first time.
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
- The SD card is full. Delete some clips (A 154) and photos (A 198) to free some space or replace the SD card.
- The folder and file numbers for MP4 clips and photos have reached their maximum value. Set [Other Functions] >
[File Numbering] to [Reset] and insert a new SD card.
Recording to and playing back from a recording media is slow.
- This may occur as clips and photos are recorded/deleted over time. Save your recordings (A 168) and initialize the
recording media (A 41).
The supplied wireless controller will not work.
- Set [Other Functions] > [Wireless Controller] to [On].
- Replace the battery of the wireless controller.
Troubleshooting
The optional RC-V100 Remote Controller or other commercially available remote control does not work.
- Make sure that [Other Functions] > [REMOTE Term.] is set to [RC-V100] when using the optional RC-V100 Remote
Controller or [Standard] when using a commercially available remote control.
- Turn off the camcorder, reconnect the RC-V100 or other remote control and then turn the camcorder back on again.
- A custom picture file saved in the camcorder must be selected to change custom picture settings using the remote
controller. Select a custom picture file from [C1] to [C9] (A 132).
English
Connections with External Devices
Video noise appears on a nearby TV screen.
- When using the camcorder in a room where a TV is located, keep a distance between the compact power adapter and
the power or antenna cables of the TV.
Playback looks fine on the camcorder but there is no image on the external monitor.
- The camcorder is not connected correctly to the external monitor. Make sure you are using the correct connection
(A 162).
- The video input on the external monitor is not set to the video terminal to which you connected the camcorder. Select
the correct video input.
The camcorder is connected using a commercially available HDMI cable, but there is no picture or sound from the
external monitor.
- Disconnect the HDMI cable and then restore the connection or turn the camcorder off and then on again.
Y
P
O
The computer does not recognize the camcorder even though the camcorder is connected correctly.
- Disconnect the optional IFC-400PCU USB Cable and turn off the camcorder. After a short while, turn it on again and
restore the connection.
- Connect the camcorder to a different USB port on the computer.
Network Functions
C
221
Cannot connect with an access point.
- Wi-Fi networks with a stealth function that do not broadcast their network name (SSID) will not be detected by the
camcorder during the Wi-Fi network setup. Perform the setup manually (A 177) or turn off the stealth function of the
access point.
- Password information is not saved with the camera settings. When you load onto the camcorder camera settings from
an SD card, all the encryption keys and passwords in the network-related settings are reset. Edit the network-related
settings as necessary (A 181, 182).
- The wireless signal is not strong enough or there are other devices in the vicinity interfering with the wireless signal.
Refer to Precautions Regarding Wi-Fi Networks (A 222).
Cannot establish a Camera Access Point connection with a Wi-Fi-enabled device.
- When you reset all the camcorder’s settings, all network settings are lost as well. Set up the Camera Access Point
settings again (A 177).
- The wireless signal is not strong enough or there are other devices in the vicinity interfering with the wireless signal.
Refer to Precautions Regarding Wi-Fi Networks (A 222).
Cannot connect with a wired (Ethernet) network.
- Use a category 5e or better shielded twisted pair (STP) LAN cable.
- Try replacing the LAN cable.
- When you reset all the camcorder’s settings, all network settings are lost as well. Set up the network settings again
(A 179).
- Check that the network device to which the camcorder is connected is on and functioning properly. To use 1000BASET connection speeds, make sure to use network devices compatible with Gigabit Ethernet (1000BASE-T).
The LAN access indicator illuminates in red and then turns off.
- The LAN cable was disconnected or the camcorder cannot communicate with the connected network device. Check
the LAN connection and the connected network device.
The Playback via Browser application will not start on the Web browser.
- Make sure to activate the function on the camcorder with the [Other Functions] > [Playback via Browser] setting
(A 193).
- The URL entered into the Web browser’s address bar is incorrect. Enter the URL exactly as it appears on the
camcorder's screen.
- The SD card slot cover is open or there is no SD card in the camcorder. Check that an SD card that contains MP4 clips
and photos is correctly inserted into the camcorder and the SD card slot cover is closed.
Troubleshooting
222
The Browser Remote application will not start on the Web browser.
- Make sure [Other Functions] > [Network Functions] is set to [Browser Remote].
- The URL entered into the Web browser’s address bar is incorrect. Check the [Network Settings 4/10] status screen
and make sure to use the IP address assigned to the camcorder as the URL (A 183).
- The user name or password is incorrect. Make sure to enter the user name and password of one of the users set on
the camcorder (A 182).
The Browser Remote or Playback via Browser screen is not displayed correctly on the Web browser.
- The device, operating system or Web browser used may not be supported. For the latest information about supported
systems, visit your local Canon Web site.
- Enable JavaScript and cookies in your Web browser's settings. For details, refer to the help modules or online
documentation of the Web browser used.
Using the Playback via Browser application, playback on a Wi-Fi-enabled device is not smooth.
- The wireless signal is not strong enough or there are other devices in the vicinity interfering with the wireless signal.
Refer to Precautions Regarding Wi-Fi Networks (A 222).
- Playback may not be smooth depending on the strength of the wireless connection.
- Try connecting the camcorder to a wired network using a LAN cable.
Precautions Regarding Wi-Fi Networks
When using a Wi-Fi network, try the following corrective actions if the transmission rate drops, the connection is
lost, or other problems occur.
Y
P
O
Location of the access point (wireless router)
- When using a Wi-Fi network indoors, place the access point in the same room where you are using the camcorder.
- Place the access point in an open, unobstructed location, where people or objects do not come between it and the
camcorder.
- Place the access point as close as possible to the camcorder. In particular, note that during outdoor use in poor
weather, rain may absorb radio waves and disrupt the connection.
Nearby electronic devices
- If the transmission rate over a Wi-Fi network drops because of interference from the following electronic devices,
switching to the 5 GHz band or to a different channel may solve the problem.
- Wi-Fi networks using the IEEE 802.11b/g/n protocol operate in the 2.4 GHz band. For this reason, the transmission
rate may drop if there are nearby microwave ovens, cordless telephones, microphones, or similar devices operating on
the same frequency band.
- If another access point operating on the same frequency band as the transmitter is used nearby, the transmission rate
may drop.
C
Using multiple camcorders/access points
- Check that there are no IP address conflicts among the devices connected to the same network.
- If multiple XF200 / XF205 camcorders are connected to a single access point, connection speeds may be reduced.
- To reduce radio wave interference when there are multiple access points using IEEE 802.11b/g or IEEE 802.11n (in the
2.4 GHz band), leave a gap of four channels between each wireless access point. For example, use channels 1, 6, and
11, channels 2, 7, and 12, or channels 3, 8, and 13. If you can use IEEE 802.11a/n (in the 5 GHz band), switch to IEEE
802.11a/n and specify a different channel.
Troubleshooting
List of Messages
Refer to this section if a message appears on the screen. The messages in this section appear in alphabetical
order. Note that for some messages, an indication of the recording media involved (CF A, CF B,
, or a
combination thereof) may appear above the message itself.
For error messages related to network connections, refer to Network Functions (A 225).
Buffer overflow. Recording was stopped.
- The data transfer rate was too high for the recording media card in use and the recording was stopped. Use a
recommended card (A 38).
Cannot acquire battery information Continue using this battery pack?
- You attached a battery pack that does not bear the Intelligent System mark.
- If you are using a battery pack that bears the Intelligent System mark, there may be a problem with the camcorder or
battery pack. Consult a Canon Service Center.
Cannot play back
- The file control information is corrupted or there was a decoder error. Turn off the camcorder and back on again. If this
does not solve the problem, consult a Canon Service Center.
• Corrupted file control information cannot be recovered. CF cards or MXF clips with corrupt file control information
cannot be read by Canon XF Utility or the Canon XF plugins.
Y
P
O
Cannot record
- The file control information is corrupted or there was an encoder error. Turn off the camcorder and back on again.
Then, remove the CF card being used and reinsert it. Alternatively, replace the CF card. If this does not solve the
problem, consult a Canon Service Center.
• Corrupted file control information cannot be recovered. CF cards or MXF clips with corrupt file control information
cannot be read by Canon XF Utility or the Canon XF plugins.
Cannot restore
- Could not recover data on the CF card. Save your MXF clips (A 168) and initialize the CF card (A 41).
C
Cannot switch CF card slots
- The SLOT SELECT button was pressed while the camcorder is recording or when the movie format is set to MP4. Wait
until recording is finished to change the selected CF card slot.
CF A/CF B error
- The CF card cannot be recognized or cannot be accessed. Check that the CF card is inserted correctly and not
malfunctioning.
CF AJCF B / CF BJCF A Switched
- This message appears when you use the SLOT SELECT button to switch the CF card slot in use or recording
continued from one CF card to the other.
CF AJCF B / CF BJCF A Will switch in a moment
- The CF card is almost full so recording will continue on the other CF card in approximately 1 minute.
Change the battery pack
- The battery pack is exhausted. Replace or charge the battery pack.
Check the data on CF A/CF B Initializing the card is also recommended
- The CF card cannot be used for any of the following reasons.
• A problem has occurred with the CF card.
• The camcorder cannot read the CF card’s data.
• The CF card was initialized using a computer.
• The CF card has been partitioned.
- Save your MXF clips (A 168) and initialize the CF card (A 41).
Check the data on
Initializing the card is also recommended
- You inserted an SD card that was formatted using another device into the camcorder. Initialize the SD card with this
camcorder.
Check the SD card
- You inserted a MultiMedia Card (MMC) or an SD card with a capacity of 64 MB or smaller into the camcorder. Use a
recommended SD card (A 38).
- Due to an SD card error, recording/playback Is not possible. Remove and then reinsert the SD card or use a different
SD card.
English
Accessing CF A/CF B/
Do not remove
- You opened the CF card slot cover or SD card slot cover while the camcorder was accessing the recording media.
Close the relevant card slot cover.
223
Troubleshooting
Cover is open
- The CF card slot cover or SD card slot cover was opened when the camcorder was switched to or turned on in
mode. Check that the recording media is correctly inserted and close the relevant card slot cover.
224
Data on CF A/CF B needs recovering Attempt to recover?
- If data on the CF card is corrupted, such as when the power suddenly turned off while recording, the data must be
recovered. When this message appears, select [OK] and then press SET.
Do not disconnect the USB cable or the power source until you safely end the connection from the computer.
- When the camcorder is in
mode and is connected to the computer with the optional IFC-400PCU USB Cable,
the camcorder cannot be operated. Disconnecting the USB cable or power source while this message appears may
corrupt the recordings on the recording media in the camcorder. Use the computer’s Safely Remove Hardware
function to end the connection and disconnect the USB cable before using the camcorder.
Fan error
- The cooling fan may not be working properly. Consult a Canon Service Center.
File name error
- The folder and file numbers have reached their maximum value. Set [Other Functions] > [File Numbering] to [Reset]
and delete all the MP4 clips (A 154) and photos (A 198) on the SD card or initialize it (A 41).
INFRARED switch position changed (ON/OFF). Check the focus.
- The focus may change when you turn the infrared mode on or off. Check that the focus is correct.
Invalid operation
- The following operations cannot be performed.
• Adding a shot mark to an MXF clip that already has a shot mark or to an MXF clip in frame recording mode or
interval recording mode.
• Adding an $ mark to an MXF clip that already has an $ mark or adding a % mark to a clip that already has a %
mark.
• In
mode, immediately reviewing a recording made in a special recording mode.
• Pressing the START/STOP button, or trying to start recording an MP4 clip, when there is no recording media in the
camcorder.
C
Y
P
O
Management data is not supported and will be deleted
- This message may appear if you insert into the camcorder a CF card that was initialized by another Canon
professional camcorder. Check the contents of the CF card.
Management file error Cannot record
- Cannot record because the camcorder cannot write to the file control information. This may occur if the MXF files on
the CF card were accessed using another device. Save your MXF clips (A 168) and initialize the CF card (A 41).
May not be possible to record movies on this memory card
- You may not be able to record MP4 clips on an SD card without a Speed Class rating or rated CLASS 2 or 4. Replace
the SD card with one rated CLASS 6 or 10.
Media full
- The recording media is full. Delete some recordings (A 154, 198) to free some space or replace the recording media.
- CF card A or CF card B is full so recording will not start. Switch to the CF card in the other CF card slot to record.
Media is almost full
- The amount of available space on CF card A and CF card B combined is low. Replace the CF card that is not selected.
- The SD card is almost full. Delete some recordings (A 154, 198) to free some space or replace the SD card.
Media is not supported
- CF cards that are less than 512 MB or not UDMA-compatible cannot be used with the camcorder. Use a
recommended CF card (A 38).
Memory card is write-protected
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
No clips
- There are no clips on the recording media to play back. Clips must be recorded (A 47) in order to play them back.
No photos
- There are no photos on the SD card to play back. Photos must be taken (A 195) in order to view them.
No Shot Marks
- This message appears if shot marks in a clip were deleted from the [Shot Mark] index screen. Press the INDEX button
to return to the MXF clip index screen.
Troubleshooting
Number of clips already at maximum
- The CF card selected for recording already contains the maximum number of MXF clips (999 clips). Replace the CF
card or use the CF card in the other CF card slot.
- Because both CF cards reached the maximum number of clips, double slot recording is not available.
Number of Shot Marks at maximum
- The shot mark could not be added because the MXF clip already contains 100 shot marks (" and # marks
combined). You must delete shot marks (A 157) before adding any more.
Recorded at 50.00 Hz Check the data on CF A/CF B Initializing the card is also recommended
- The CF card contains MXF clips that were recorded using a system frequency different from the one used by the
camcorder. Back up the content of the CF card if necessary and initialize the CF card with this camcorder (A 41).
Recording was stopped.
- The file control information is corrupted or there was an encoder error. Turn off the camcorder and back on again.
Then, remove the CF card being used and reinsert it. Alternatively, replace the CF card. If this does not solve the
problem, consult a Canon Service Center.
• Corrupted file control information cannot be recovered. CF cards or clips with corrupt file control information cannot
be read by Canon XF Utility or the Canon XF plugins.
Shot Mark Error
- Could not add a shot mark. If the message appears in
mode, try adding the mark again. If that does not work,
add the mark in
mode after you finish recording. If the message appears in
mode, turn off the
camcorder and then back on. Then, try to add the mark again.
Y
P
O
System error
- Turn off the camcorder and back on again. If this does not solve the problem, there may be a malfunction with the
camcorder. Consult a Canon Service Center.
The sound of the Zoom motor may also be recorded.
- Be careful when operating the zoom while recording as the sound of the zoom motor may be recorded as well. Try
zooming while the camcorder in record pause mode.
C
This clip needs recovering. Attempt to recover?
- If the clip is corrupted, such as when the power suddenly turned off while recording, the clip must be recovered. When
this message appears, select [OK] and then press SET.
This photo cannot be displayed
- You may not be able to display photos taken with other devices or image files created or edited on a computer.
Using a card that supports UDMA mode 4 or higher is recommended
- The CF card’s UDMA mode is lower than UDMA4. We recommend using a CF card that with a UDMA mode of at least
UDMA4.
% / $ Mark Error
- Could not add a % mark or $ mark. If the message appears in
not work, add the mark in
mode. If the message appears in
on. Then, try to add the mark again.
mode, try adding the mark again. If that does
mode, turn off the camcorder and then back
Network Functions
Along with this list, refer also to the instruction manuals of the access point or other external devices you are
using.
A User is already accessing the server. Try again later.
- This message appears on the screen of the connected device. Another device connected to the network is already
operating the camcorder. To use this device, first end the connection on the device accessing the camcorder and then
touch Retry.
Cannot create new folder on the FTP server.
- Check the user permissions/restrictions for accessing the FTP server.
Cannot log in to FTP server.
- Check the user name and password information in the FTP server settings (A 189).
English
Reached the recording limit for one clip. Recording was stopped.
- When recording a single MXF clip for an extended period of time, the clip will be split into smaller video files every
2 GB (or 1 GB when recording in slow motion). This message will appear when the number of smaller video files
reaches 99.
225
Troubleshooting
Cannot transfer files to FTP server.
- Check that there is enough available space in the data storage device (hard disk, etc.) that contains the destination
folder on the FTP server.
226
Check the Media.
- An error occurred with the recording media while files were being transferred to the FTP server. Check the recording
media from which you are transferring files and try the FTP transfer operation again.
Check the network configuration.
- The camcorder could not connect to the network using the current settings. Check that the network settings are
correctly configured (A 215).
File transfer was not completed.
- The camcorder was turned off while the last FTP transfer operation was still in progress. Transfer the files again
(A 189).
FTP server not found.
- The FTP server could not be found. Check the FTP server settings (A 189).
FTP transfer error. File transfer was not completed.
- An error occurred while transferring files to the FTP server. Turn then camcorder and the FTP server off and then on
again and try again the FTP transfer.
IP address conflict
- Another device on the same network has the same IP address assigned to the camcorder. Change the IP address of
the conflicting device or the camcorder.
Y
P
O
LAN cable not connected.
- You attempted to connect to a wired network but the LAN cable is not connected. Check that the LAN cable is
correctly connected to the camcorder's LAN terminal and to the LAN port on the network device.
Memory card cover was opened so network functions will be interrupted.
- The CF card slot cover or SD card slot cover was opened while the recording media was being accessed. Stop the
network function in use and end the network connection.
Multiple access points detected. Try the operation again.
- There are multiple access points sending out a WPS signal at the same time. Try the operation again later or perform
setup using the [WPS: PIN Code] or [Search for Access Points] option (A 175).
C
Network connection terminated
- An error occurred on the access point or connected device. Check the network or connected and try connecting
again.
- The Wi-Fi signal became too weak and the wireless connection was lost. Wait a moment or turn off other devices in
the area that may be interfering with the Wi-Fi signal and then try connecting again.
Network is not working correctly
- There’s a hardware problem with the camcorder’s network related circuitry. Try turning the camcorder off and the on
again. If the problem persists, consult a Canon Service Center.
No access points found
- The camcorder searched for active Wi-Fi networks (access points) in the area but none were found. Make sure the
access point is working correctly and try connecting again.
- The access point is operating in stealth mode. Deactivate the stealth function in the wireless router (access point)
settings.
- The connection wizard may not be able to find the access point if MAC address filtering is activated. Check the
[Network Settings 1/10] status screen (A 215) and make sure to add the camcorder’s MAC address to the list of
approved wireless devices in the wireless router (access point) settings.
No files available for transfer.
- All the files selected for transfer have already been transferred to the FTP server.
Unable to complete WPS.
- The access point’s encryption method is set to [WEP]. Wi-Fi Protected Setup (WPS) cannot connect to access points
set to this encryption method. Change the access point’s encryption method or use another connection method
(A 174).
Unable to complete WPS. Try the operation again.
- More than 2 minutes passed between activating WPS on the access point and selecting [OK] on the camcorder. Start
over the WPS procedure from the beginning.
- The WPS button was not held down long enough. Refer to the instruction manual of your wireless router. When using
WPS to make a wireless connection, keep the WPS button held down until the wireless router’s WPS function is
activated.
Troubleshooting
Unable to connect
- Could not connect to the access point or network device selected.
- Cordless phones, microwave ovens, refrigerators and other appliances may interfere with the wireless signal. Try using
the camcorder in a location farther away from such appliances.
Wi-Fi authentication unsuccessful
- Check the access point’s authentication/encryption method and encryption key and change the camcorder’s Wi-Fi
settings (A 181) as necessary.
Wi-Fi cannot be used while the wireless microphone is attached.
- Wi-Fi connections cannot be used while an optional WM-V1 Wireless Microphone is attached to the camcorder.
Disconnect the WM-V1 from the camcorder and turn it off.
Wi-Fi error. Incorrect authentication method
- Check the access point’s authentication/encryption method and change the camcorder’s Wi-Fi settings (A 181) as
necessary.
Y
P
O
Wi-Fi error. Incorrect encryption key.
- When the authentication mode was set to [WPA-PSK] or [WPA2-PSK], or the encryption method was set to [WEP], the
encryption key (WEP index) entered or its length (number of characters) is incorrect.
• When entering ASCII characters, enter 5 characters (64-bit encoding) or 13 characters (128-bit encoding). When
entering hexadecimal characters, enter 10 characters (64-bit encoding) or 26 characters (128-bit encoding).
C
Wi-Fi error. Incorrect encryption method
- Make sure the camcorder and access point are using the same authentication/encryption method.
227
English
Unable to obtain an IP address
- If you are not using a DHCP server, connect using the [Manual] option and enter the IP address using the [Manual]
option (A 178).
- Turn on the DHCP server. If it is already on, make sure it is functioning properly.
- Make sure the address range for the DHCP server is sufficient.
- If you are not using a DNS server, set the DNS address to [0.0.0.0].
- Set the DNS server’s IP address in the camcorder.
- Turn on the DNS server. If it is already on, make sure it is functioning properly.
- Make sure that the DNS server’s IP address and the name for that address are correctly configured.
- If you are using a wireless gateway router, make sure all of the devices in the network, including the camcorder, are
configured with the correct gateway address.
Handling Precautions
Handling Precautions
Camcorder
228
Be sure to observe the following precautions to ensure maximum performance.
• Do not carry the camcorder by the OLED panel. Be careful when closing the OLED panel.
• Do not leave the camcorder in places subject to high temperatures (like the inside of a car parked under direct
sunlight), or high humidity.
• Do not use the camcorder near strong electromagnetic fields such as near powerful magnets and motors, MRI
machines or high-voltage power lines. Using the camcorder in such places may cause anomalies in the video or
audio or video noise to appear.
• Do not use the camcorder’s Wi-Fi functions inside hospitals, medical clinics or onboard aircraft. In addition, do
not use them near medical equipment or sensitive electronic devices as it may affect their performance. In the
case of pacemakers, keep the camcorder at least 22 cm (8.7 in.) away from the device.
• The camcorder’s Wi-Fi functions may be subject to interference from devices such as cordless phones and
microwave ovens. Keeping as much distance as possible from these devices or using the camcorder’s Wi-Fi
functions at a different time of day may reduce such interference.
• Do not use or store the camcorder in dusty or sandy places. The camcorder is not waterproof – avoid also
water, mud or salt. If any of the above should get into the camcorder it may damage the camcorder and/or the
lens. Consult a Canon Service Center as soon as possible.
• Be careful to avoid dust and dirt particles accumulating on the lens or entering the camcorder. When you finish using
the camcorder, make sure to remove the lens hood and attach the lens cap to the camcorder.
• Do not point the camcorder or viewfinder toward an intense light source, such as the sun on a sunny day or an
intense artificial light source. Doing so may damage the image sensor or the camcorder’s internal
components. Be careful especially when using a tripod or shoulder strap. When you are not using the
camcorder, make sure to attach the lens cap to the camcorder.
• Be careful of heat generated by lighting equipment.
• Do not disassemble the camcorder. If the camcorder does not function properly, consult qualified service
personnel.
• Handle the camcorder with care. Do not subject the camcorder to shocks or vibration as this may cause
damage. When using the shoulder strap, do not allow the camcorder to swing and hit an object.
C
Y
P
O
Long-term storage
If you do not intend to use the camcorder for a long time, store it in a place free of dust, in low humidity, and at
temperatures not higher than 30 °C (86 °F).
Battery Pack
DANGER!
Treat the battery pack with care.
• Keep it away from fire (or it might explode).
• Do not expose the battery pack to temperature higher than 60 °C (140 °F). Do not leave it near a heater or
inside a car in hot weather.
• Do not try to disassemble or modify it.
• Do not drop it or subject it to shocks.
• Do not get it wet.
• Dirty terminals may cause a poor contact between the battery pack and the camcorder. Wipe the terminals
with a soft cloth.
Handling Precautions
Long-term storage
• Store battery packs in a dry place at temperatures no higher than 30 °C (86 °F).
• To extend the battery life of the battery pack, discharge it completely before storing it.
• Charge and discharge all your battery packs fully at least once a year.
229
Do not allow any metal objects to touch the terminals (figure 1), as this can
cause a short circuit and damage the battery pack. Attach the terminal cover
whenever the battery pack is not being used (figure 2).
The battery terminal cover has a [ð]-shaped hole. This is useful when you
wish to differentiate between charged and uncharged battery packs. For
example, with charged battery packs, attach the terminal cover so that the
[ð]-shaped hole shows the colored label.
Back side of the
battery pack
English
Always attach the battery terminal cover.
Figure 1
Figure 2
Terminal cover attached
Charged
Uncharged
Y
P
O
Remaining battery time
When using a battery pack compatible with Intelligent System, if the remaining battery time displayed is not
correct, charge the battery pack fully. Still, the correct time may not be displayed if a fully charged battery pack is
used continuously in high temperatures or it is left unused for long periods of time. Also, the correct remaining
time may not be displayed, depending on the battery life. Use the time shown on the screen as an
approximation.
C
Regarding the use of non-Canon battery packs
• We recommend using genuine Canon battery packs bearing the Intelligent System
mark.
• If you attach to the camcorder battery packs that are not genuine Canon battery packs, the remaining battery
time will not be displayed.
Recording Media
• We recommend backing up the recordings on the recording media onto your computer. Data may be
corrupted or lost due to defects or exposure to static electricity. Canon shall not be liable for lost or corrupted
data.
• Do not touch or expose the terminals to dust or dirt.
• Do not use recording media in places subject to strong magnetic fields.
• Do not leave recording media in places subject to high humidity and high temperature.
• Do not disassemble, bend, drop, or subject recording media to shocks and do not expose them to water.
• Check the direction before inserting the recording media. Forcing recording media into the slot if it is not
correctly oriented may damage the recording media or the camcorder.
• Do not attach any labels or stickers on the recording media.
Handling Precautions
• SD cards: SD cards have a physical switch to prevent writing on the card so as to
avoid the accidental erasure of the card’s content. To write-protect the SD card,
set the switch to the LOCK position.
230
Disposal
LOCK switch
When you delete data on the recording media, only the file allocation table is altered
and stored data is not physically erased. Take the necessary precautions when you dispose of the recording
media, for example by physically damaging it to prevent the leakage of private data.
If giving the recording media to another person, initialize it (using the [Complete] initialization option for SD cards,
A 41). Fill it up with unimportant recordings, and then initialize it again. This makes recovering the original
recordings very difficult.
Built-in Rechargeable Lithium Battery
The camcorder has a built-in rechargeable lithium battery to keep the date/time and other settings. The built-in
lithium battery is recharged while you use the camcorder; however, it will discharge completely if you do not use
the camcorder for about 3 months.
To recharge the built-in lithium battery: Connect the compact power adapter to the camcorder and use a
household power outlet to power the camcorder for 24 hours while it is turned off.
Lithium Button Battery
WARNING!
C
Y
P
O
• The battery used in this device may present a fire or chemical burn hazard if mishandled.
• Do not disassemble, modify, immerse in water, heat above 100 °C (212 °F) or incinerate the battery.
• Replace with a CR2025 battery made by Panasonic, Hitachi Maxell, Sony, Sanyo, or with Duracell2025.
Use of other batteries may present a risk of fire or explosion.
• Do not insert the battery into the mouth. If swallowed, seek medical assistance immediately. The battery
case may break and the battery fluids may cause internal injuries.
• Keep the battery out of the reach of children.
• Do not recharge, short-circuit or insert the battery in the wrong direction.
• Dispose of the used battery according to applicable recycling regulations.
• Do not pick up the battery using tweezers or other metal tools, as this will cause a short circuit.
• Wipe the battery with a clean dry cloth to ensure proper contact.
• For CA, USA only
Included lithium battery contains Perchlorate Material - special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate/ for details.
Maintenance/Others
Maintenance/Others
Cleaning
Lens and Instant AF Sensor
• If the lens surface or Instant AF sensor is dirty, autofocus may not work properly.
• Remove any dust or dirt particles using a non-aerosol type blower brush.
• Use a clean, soft lens-cleaning cloth to gently wipe the lens and sensor using commercially available cleaning
fluid for eyeglasses. Never use tissue paper.
OLED Screen
• Clean the OLED screen using a clean, soft lens-cleaning cloth.
• Condensation may form on the surface of the screen when the temperature changes suddenly. Wipe it with a
soft dry cloth.
Condensation
Y
P
O
Moving the camcorder rapidly between hot and cold temperatures may cause condensation (water droplets) to
form on its internal surfaces. Stop using the camcorder if condensation is detected. Continued use may damage
the camcorder.
C
Condensation may form in the following cases:
• When the camcorder is moved quickly from cold to warm places
• When the camcorder is left in a humid room
• When a cold room is heated rapidly
To avoid condensation
• Do not expose the camcorder to sudden or extreme changes in temperature.
• Remove the recording media and battery pack. Then, place the camcorder in an airtight plastic bag and let it
adjust gradually to temperature changes before removing it from the bag.
When condensation is detected
The camcorder automatically shuts off.
The precise time required for water droplets to evaporate will vary depending on the location and weather
conditions. As a general rule, wait for 2 hours before resuming use of the camcorder.
Using the Camcorder Abroad
Power Sources
You can use the compact power adapter to operate the camcorder and to charge battery packs in any country
with power supply between 100 and 240VAC, 50/60Hz. Consult a Canon Service Center for information on plug
adapters for overseas use.
231
English
Camcorder Body
• Use a soft, dry cloth to clean the camcorder body. Never use chemically treated cloths or volatile solvents
such as paint thinner.
Optional Accessories
Optional Accessories
The following optional accessories are compatible with this camcorder. The availability differs from area to area.
232
BP-950G, BP-955,
BP-970G, BP-975
Battery Pack
CA-930 Compact
Power Adapter
WA-H58 Wide
Attachment
TL-H58 Tele-converter
C
Y
P
O
DC-930 DC Cable
Protect Filter 58 mm,
ND4L Filter 58 mm,
ND8L Filter 58 mm
RC-V100 Remote
Controller
GP-E2
GPS Receiver
TA-100 Tripod Adapter
TB-1 Tripod Adapter
Base
STV-250N
Stereo Video Cable
IFC-400PCU
USB Cable
For our customers in the USA: Call or visit your local retailer/dealer for genuine Canon video accessories. You
can also obtain genuine accessories for your Canon camcorder by calling: 1-800-828-4040, Canon U.S.A.
Information Center.
Optional Accessories
Use of genuine Canon accessories is recommended.
This product is designed to achieve excellent performance when used with genuine Canon accessories.
Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the
malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack). Please
note that this warranty does not apply to repairs arising out of the malfunction of non-genuine Canon
accessories, although you may request such repairs on a chargeable basis.
BP-975
*The optional BP-970G / BP-975 Battery Pack were not originally designed for use
with this camcorder.
Charging Times
Use the supplied CA-930 Compact Power Adapter to charge battery packs. The charging times given in the
following table are approximate and vary according to charging conditions and initial charge of the battery pack.
BP-950G
BP-955
BP-970G
245 min.
200 min.
350 min.
Recording and Playback Times
Y
P
O
BP-975
295 min.
Recording and playback times given in the following tables are approximate and were measured under the
following conditions:
The 3G/HD-SDI terminal and MON. terminal are turned off.
- The OLED screen and viewfinder are both turned on.
- Typical recording times measure recording with repeated operations such as start/stop recording and power
on/off.
Actual times will vary according to recording mode and charging, recording or playback conditions. The effective
usage time of the battery pack may decrease when recording in cold surroundings, when using the brighter
screen settings, etc.
C
English
BP-955
Battery Packs
When you need extra battery packs, select from the following: BP-950G,
BP-955, BP-970G*, BP-975*.
When you use battery packs bearing the Intelligent System mark, the
camcorder will communicate with the battery and display the remaining
usage time (accurate to 1 minute). You can only use and charge these battery
packs with camcorders and chargers compatible with Intelligent System.
233
Optional Accessories
Movie format
(bit rate)
234
MXF (50 Mbps)
MP4 (35 Mbps)
Movie format
(bit rate)
MXF (50 Mbps)
MP4 (35 Mbps)
Usage time
BP-950G
BP-955
BP-970G
BP-975
Recording (maximum)
270 min.
260 min.
380 min.
380 min.
Recording (typical)
160 min.
150 min.
220 min.
235 min.
Playback
375 min.
360 min.
520 min.
520 min.
Recording (maximum)
280 min.
265 min.
390 min.
390 min.
Recording (typical)
165 min.
155 min.
225 min.
240 min.
Playback
365 min.
350 min.
510 min.
515 min.
BP-950G
BP-955
BP-970G
BP-975
Recording (maximum)
260 min.
250 min.
360 min.
360 min.
Recording (typical)
150 min.
150 min.
220 min.
235 min.
Playback
345 min.
335 min.
485 min.
490 min.
Recording (maximum)
275 min.
260 min.
380 min.
385 min.
Recording (typical)
160 min.
150 min.
220 min.
235 min.
Playback
360 min.
345 min.
505 min.
505 min.
Usage time
C
Y
P
O
TA-100 Tripod Adapter
The TA-100 allows you to quickly mount/unmount the
camcorder on/from a tripod.
This mark identifies genuine Canon video accessories. When you use Canon video equipment, we
recommend Canon-brand accessories or products bearing the same mark.
Specifications
Specifications
XF200 / XF205
System
235
• Video Configuration (recording/playback)
MXF Movies:
50 Mbps (CBR, 4:2:2, 422P@HL)
1920x1080: 59.94i, 29.97P, 23.98P
1280x720: 59.94P, 29.97P, 23.98P
35 Mbps (VBR, 4:2:0, MP@HL)
1920x1080: 59.94i, 29.97P, 23.98P
1440x1080: 59.94i
1280x720: 59.94P, 29.97P, 23.98P
25 Mbps (CBR, 4:2:0, MP@H14)
1440x1080: 59.94i, 29.97P, 23.98P
MP4 Movies (audio bit rate give in brackets [ ]):
35 Mbps (VBR)
1920x1080: 59.94P [256 kbps]
24 Mbps (VBR)
1920x1080: 29.97P, 23.98P [256 kbps]
17 Mbps (VBR)
1280x720: 59.94P [128 kbps]
9 Mbps (VBR)
1280x720: 29.97P, 23.98P [128 kbps]
3 Mbps (VBR)1
640x360: 29.97P, 23.98P [128 kbps]
C
1
Y
P
O
Only when the movie format is set to MXF+MP4.
• Recording Media (not included)
MXF Movies: CompactFlash (CF) Card Type I (two slots)
MP4 Movies and Photos: SD, SDHC (SD High Capacity) or SDXC (SD eXtended Capacity) memory card2
2
Custom picture files, camera settings and user memo files can be saved on and read from the SD card as well.
• Maximum Recording Time (approximate, continuous recording)
MXF Movies:
16 GB CF Card
50 Mbps: 40 min., 35 Mbps: 55 min., 25 Mbps: 80 min.
64 GB CF Card
50 Mbps: 160 min., 35 Mbps: 225 min., 25 Mbps: 310 min.
MP4 Movies:
16 GB SD card
35 Mbps: 60 min., 24 Mbps: 85 min., 17 Mbps: 125 min., 9 Mbps: 235 min., 3 Mbps: 685 min.
32 GB SD card
35 Mbps: 120 min., 24 Mbps: 175 min., 17 Mbps: 255 min., 9 Mbps: 470 min., 3 Mbps: 1375 min.
English
• Recording System
MXF Movies: Video compression: MPEG-2 Long GOP
Audio compression: Linear PCM, 16 bits, 48 kHz, 2 or 4 channels
File format: MXF
MP4 Movies: Video compression: MPEG-4 AVC/H.264
Audio compression: MPEG-4 AAC-LC, 16 bits, 48 kHz, 2 channels
File format: MP4
Photos:
DCF (Design rule for Camera File system), compatible with Exif Ver. 2.3, JPEG compression
Specifications
• Image Sensor: 1/2.84-in. CMOS sensor, approx. 2,910,000 pixels (2136x1362)
• OLED Screen: 3.5 in. organic LED display, equivalent to approx. 1,230,000 dots, 100% coverage
• Viewfinder: 0.45 in. color LCD, equivalent to approx. 1,230,000 dots, 99.8% coverage
236
• Lens
f=3.67-73.4 mm, F/1.8-2.8, 20x optical zoom, 8-bladed circular aperture
35 mm equivalent: 28.8 – 576 mm (26.8 – 576 mm when the angle of view at full wide-angle is set to
[Wider])
• Lens Configuration: 12 elements in 10 groups (2 aspheric elements)
• Filter Diameter: 58 mm
• Minimum Focusing Distance
60 cm (2 ft.) throughout the zoom range; 1 cm (0.39 in.) (at full wide angle with [Focus Limit] set to [Off])
• AF System
Autofocus (TTL + external distance sensor when the AF [Speed] is set to [High] (Instant AF) or [Medium]
(Medium AF)), or manual focus
• Image Stabilization
Optical-Shift Image Stabilizer + digital compensation (Standard IS, Dynamic IS, Powered IS)
Y
P
O
• Subject Illumination (full auto mode set to OFF, frame rate set to 59.94i , gain at 33 dB, shutter speed at
1/4)
Minimum Illumination: 0.1 lux
Illumination Range: 0.1 lux to 10,000 lux
• ND Filter: Graduated ND filter, 3 automatic settings (1/2, 1/4, 1/8)
• Iris: Automatic or manual
C
• Gain
-6 dB to 27 dB (3-dB increments), 33 dB; 6.0 dB to 27.0 dB (fine-tuning in 0.5-dB increments)
• Shutter
Automatic, speed (normal increments or fine-tuning), angle, clear scan, slow shutter or off
• Exposure: Full automatic ON/OFF; AE shift; 3 light metering modes (standard, spotlight or backlight)
• White Balance
Auto white balance (AWB); two preset settings (daylight, 5,400 K3 and incandescent lamp, 3,200 K3) that can be
further fine-tuned; color temperature setting (2,000 K to 15,000 K); custom white balance (two sets, A and B)
3
Color temperatures are approximate and given for reference purposes only.
• Digital zoom: Digital zoom (120x); digital tele-converter (1.5x, 3.0x, 6.0x)
• Infrared mode: Available, including built-in infrared light
• Microphone: Stereo electret condenser microphone
• Size of Photos
1920x1080 pixels, 1280x720 pixels (
mode only)
Wi-Fi
• Wireless Standard: IEEE802.11b/g/n (2.4 GHz band), IEEE802.11a/n (5 GHz band)
• Connection Methods: Wi-Fi Protected Setup (WPS), search for access points, manual, Camera Access Point
• Supported Channels: See the following sidebar.
• Authentication Methods: Open, WPA-PSK, WPA2-PSK
• Encryption Methods: WEP-64, WEP-128, TKIP, AES
Specifications
• Maximum Data Transfer Rates (theoretical values):
11 Mbps (IEEE802.11b), 54 Mbps (IEEE802.11a/g), 150 Mbps (IEEE802.11n)
Available frequencies and channels
The camcorder’s Wi-Fi functions operate in a predetermined range of frequencies and channels. Note that
not all channels may be available for a direct Camera Access Point connection with Wi-Fi-enabled devices.
Channels
Available for Camera Access
Point connections
2412 MHz to 2462 MHz
1 to 11
Yes
5280 MHz to 5320 MHz
56 to 64
No
5745 MHz to 5805 MHz
149 to 161
Yes
Terminals
•
3G/HD-SDI Terminal
BNC jack, output only, 0.8 Vp-p / 75 Ω, unbalanced
3G-SDI:
SMPTE 424M, SMPTE ST 425-1
Video (1080P), embedded audio, time code (VITC/LTC)
HD-SDI:
SMPTE 292-1
Video (1080i or 720P), embedded audio, time code (VITC/LTC)
•
MON. Terminal
BNC jack, output only, 0.8 Vp-p / 75 Ω, unbalanced
HD-SDI:
SMPTE 292-1
Video (1080P, 1080i or 720P), embedded audio, time code (VITC/LTC)
SD-SDI:
SMPTE 259M
Video (480i), embedded audio, time code (VITC/LTC)
C
Y
P
O
• HDMI OUT Terminal
HDMI connector, output only, supports 1080/59.94P output
• AV OUT Terminal
∅ 3.5 mm stereo mini-jack, output only
Video: SD composite signal, 1 Vp-p / 75 Ω, unbalanced
Audio: -10 dBV (47 kΩ load) / 3 kΩ or less, stereo
• INPUT 1, INPUT 2 Terminals
XLR jack (pin1: shield, pin2: hot, pin3: cold), 2 sets
Sensitivity
MIC setting: -60 dBu (manual volume center, full scale -18 dB) / 600 Ω
LINE setting: 4 dBu (manual volume center, full scale -18 dB) / 10 kΩ
Microphone attenuator: 20 dB
• MIC Terminal
∅ 3.5 mm stereo mini-jack, -72 dBV (manual volume center, full scale -18 dB) / 600 Ω
Microphone attenuator: 20 dB
• × (Headphone) Terminal
∅ 3.5 mm stereo mini-jack, -G to -12 dBV (16 Ω load, volume range Min to Max) / 50 Ω or less
•
GENLOCK/SYNC OUT Terminal
BNC jack, input only (GENLOCK setting)/output only (SYNC OUT setting), 1 Vp-p / 75 Ω
•
TIME CODE Terminal
BNC jack, input/output
Input: 0.5 Vp-p to 18 Vp-p / 10 kΩ
Output: 1 Vp-p / 50 Ω
English
Frequency
237
Specifications
• LAN Terminal: Ethernet, 1000BASE-T
• USB Terminal: mini-B receptacle, Hi-Speed USB, output only
• REMOTE Terminal: ∅ 2.5 mm stereo mini-jack
238
Power/Others
• Power Supply (rated)
7.4 V DC (battery pack), 8.4 V DC (DC IN)
• Power Consumption (recording MXF clips at 50 Mbps, using autofocus, viewfinder/OLED screen normal
brightness, SDI output off)
8.2 W
8.4 W
• Operating Temperature
0 – 40 °C (32 – 104 °F)
• Dimensions (W x H x D)*
Camcorder only: 144 x 158 x 264 mm (5.7 x 6.2 x 10.4 in.)
Camcorder with microphone holder unit, lens hood and eye cup: 160 x 201 x 353 mm (6.3 x 7.9 x 13.9 in.)
* All dimensions are approximate.
• Weight (camcorder only)**
1,510 g (3.3 lb.)
Y
P
O
1,560 g (3.4 lb.)
**All weights are approximate.
CA-930 Compact Power Adapter
C
• Rated input
100 – 240 V AC, 50/60 Hz
As a power adapter: 46 VA (100 V) – 62 VA (240 V)
As a battery charger: 40 VA (100 V) – 54 VA (240 V)
• Rated output
As a power adapter: 8.4 V DC, 2.4 A
As a battery charger: 8.4 V DC, 1.5/2.0 A
• Operating temperature: 0 – 40 °C (32 – 104 °F)
• Dimensions (W x H x D): 85 x 51 x 110 mm (3.3 x 2.0 x 4.3 in.)
• Weight: 240 g (8.5 oz.)
BP-955 Battery Pack
• Battery Type
Rechargeable lithium ion battery, compatible with Intelligent System
• Rated Voltage: 7.4 V DC
• Battery Capacity
Typical: 5,200 mAh
Minimum: 37 Wh / 4,900 mAh
• Operating Temperature: 0 – 40 °C (32 – 104 °F)
• Dimensions (W x H x D): 38.2 x 43.5 x 70.5 mm (1.5 x 1.7 x 2.8 in.)
• Weight: 220 g (7.8 oz)
Specifications
239
English
C
Y
P
O
Weight and dimensions are approximate. Errors and omissions excepted.
The information in this manual is verified as of June 2014. Subject to change without notice.
Specifications
240
C
Y
P
O
Index
241
A
Abroad, using the camcorder . . . . . . . . . . . . . .231
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . .232
AE shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
AGC (automatic gain control) . . . . . . . . . . . . . . .62
AGC limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Air intake vents . . . . . . . . . . . . . . . . . . . . . . . . .54
Angle of view (wide-angle end) . . . . . . . . . . . . . .74
Aperture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Aspect ratio . . . . . . . . . . . . . . . . . . . . . . . . . . .165
Assignable buttons . . . . . . . . . . . . . . . . . . . . .129
Audio output channels . . . . . . . . . . . . . . . . . . .166
Audio peak limiter . . . . . . . . . . . . . . . . . . . . . .106
Audio recording . . . . . . . . . . . . . . . . . . . . . . . . .98
Audio recording level . . . . . . . . . . . . . . . .105, 106
Audio reference signal . . . . . . . . . . . . . . . . . . .107
AV OUT terminal . . . . . . . . . . . . . . . . . . .162, 164
AWB (auto white balance) . . . . . . . . . . . . . . . . .70
B
C
Clips
Adding an $ mark/% mark . . . . 110, 152
Adding/Deleting shot marks . . . . 110, 157
Copying . . . . . . . . . . . . . . . . . . . . . . . 153
Deleting . . . . . . . . . . . . . . . . . . . . . . . 154
Displaying clip information . . . . . . . . . . 151
Playback . . . . . . . . . . . . . . . . . . . . . . . 147
Recording . . . . . . . . . . . . . . . . . . . 47, 123
Saving to a computer . . . . . . . . . . . . . 168
Color bars . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Condensation . . . . . . . . . . . . . . . . . . . . . . . . 231
Connection to an external monitor . . . . . . . . . 162
Conversion lens . . . . . . . . . . . . . . . . . . . . . . . . 80
Cooling fan . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Custom displays . . . . . . . . . . . . . . . . . . . . . . 142
Custom functions . . . . . . . . . . . . . . . . . . . . . . 141
Custom picture . . . . . . . . . . . . . . . . . . . . . . . 132
Custom picture settings . . . . . . . . . . . . . . . . . 135
Y
P
O
Battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Remaining battery charge . . . . . . . . . . . .25
Bit rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Browser Remote . . . . . . . . . . . . . . . . . . . . . . . .44
Built-in backup battery . . . . . . . . . . . . . . . . . . .230
C
Camera settings . . . . . . . . . . . . . . . . . . . . . . . .143
CameraAccess plus . . . . . . . . . . . . . . . . . . . . .188
CF card
Compatible CF cards . . . . . . . . . . . . . . .38
Initializing . . . . . . . . . . . . . . . . . . . . . . . .41
Inserting/Removing . . . . . . . . . . . . . . . . .39
Recording method . . . . . . . . . . . . . . . . .42
Recovering data . . . . . . . . . . . . . . . . . . .43
Switching CF card slots . . . . . . . . .41, 146
Check marks (%) . . . . . . . . . . . . . . . . . .110, 152
D
Data Import Utility . . . . . . . . . . . . . . . . . . . . . 170
Date and time . . . . . . . . . . . . . . . . . . . . . . . . . 27
Date format . . . . . . . . . . . . . . . . . . . . . . . . . . 204
DC IN terminal . . . . . . . . . . . . . . . . . . . . . . . . . 25
Digital tele-converter . . . . . . . . . . . . . . . . . . . . 74
Direct setting mode . . . . . . . . . . . . . . . . . . . . . 57
Double slot recording . . . . . . . . . . . . . . . . . . . . 42
Drop frame (time code) . . . . . . . . . . . . . . . . . . 91
E
Edge monitor . . . . . . . . . . . . . . . . . . . . . . . . . 109
Exposure compensation . . . . . . . . . . . . . . . . . 67
Eye cup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
F
File numbering . . . . . . . . . . . . . . . . . . . . . . . . 117
Flicker reduction . . . . . . . . . . . . . . . . . . . . . . . . 61
Focal length guide . . . . . . . . . . . . . . . . . . . . . 128
Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Face AF . . . . . . . . . . . . . . . . . . . . . . . . 85
Focus assistance functions . . . . . . . . . . 84
PUSH AF (momentary autofocus) . . . . . 85
Focus limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Frame rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Frame recording mode . . . . . . . . . . . . . . . . . . 119
Free-run (time code) . . . . . . . . . . . . . . . . . . . . . 90
*
only
English
3G/HD-SDI terminal* . . . . . . . . . . . . . . . .162, 163
4-channel audio recording . . . . . . . . . . . . .98, 100
242
FTP transfer . . . . . . . . . . . . . . . . . . . . . . . . . . .189
Full auto mode . . . . . . . . . . . . . . . . . . . . . . . . . .49
G
Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Genlock* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
GENLOCK terminal* . . . . . . . . . . . . . . . . . . . . .94
GPS information . . . . . . . . . . . . . . . . . . . . . . .114
Grip belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Grip unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
H
HDMI OUT terminal . . . . . . . . . . . . . . . . . . . . .164
Headphone terminal . . . . . . . . . . . . . . . . . . . .106
Hour meter . . . . . . . . . . . . . . . . . . . . . . . . . . .208
I
Y
P
O
Image stabilizer . . . . . . . . . . . . . . . . . . . . . . . . .87
Index screens
Changing clip thumbnail . . . . . . . . . . . .158
Clips . . . . . . . . . . . . . . . . . . . . . . . . . . .145
Expand clip . . . . . . . . . . . . . . . . . . . . .156
Shot marks . . . . . . . . . . . . . . . . . . . . .155
Infrared light . . . . . . . . . . . . . . . . . . . . . . . . . . .126
Infrared recording . . . . . . . . . . . . . . . . . . . . . .126
Initializing recording media . . . . . . . . . . . . . . . . .41
INPUT 1/INPUT 2 terminals . . . . . . . . . . . .98, 103
Interval recording mode . . . . . . . . . . . . . . . . . .118
Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
C
Magnification . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Menu settings . . . . . . . . . . . . . . . . . . . . . . . . .199
Message list . . . . . . . . . . . . . . . . . . . . . . . . . . .223
Metadata . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
MIC terminal . . . . . . . . . . . . . . . . . . . . . . .98, 101
Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Microphone attenuator . . . . . . . . . . . . . . . . . .104
Microphone holder unit . . . . . . . . . . . . . . .32, 100
Microphone sensitivity . . . . . . . . . . . . . . .104, 106
MON. terminal* . . . . . . . . . . . . . . . . . . . .162, 163
Monitoring audio . . . . . . . . . . . . . . . . . . .106, 167
Movie format (MXF/MP4) . . . . . . . . . . . . . . . . . .55
My Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
J
Joystick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Joystick guide . . . . . . . . . . . . . . . . . . . . . . . . .148
K
Key lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
L
LAN terminal . . . . . . . . . . . . . . . . . . . . . . . . . .179
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Lens hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Light metering mode . . . . . . . . . . . . . . . . . . . . .68
M
Macro shooting . . . . . . . . . . . . . . . . . . . . . . . . .86
N
ND filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Network functions . . . . . . . . . . . . . . . . . . . . . .173
Non-drop frame (time code) . . . . . . . . . . . . . . . .91
O
OK marks ($) . . . . . . . . . . . . . . . . . . . . .110, 152
OLED screen . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Onscreen displays . . . . . . . . . . . . . . . . . . .51, 147
Onscreen markers . . . . . . . . . . . . . . . . . . . . . . .88
P
Peaking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Phantom power (microphone) . . . . . . . . . . . . .103
Photos
Deleting . . . . . . . . . . . . . . . . . . . . . . . .198
Recording . . . . . . . . . . . . . . . . . . . . . .195
Viewing . . . . . . . . . . . . . . . . . . . . . . . .197
Playback
Clips . . . . . . . . . . . . . . . . . . . . . . . . . . .147
Photos . . . . . . . . . . . . . . . . . . . . . . . . .197
Playback via Browser . . . . . . . . . . . . . . . . . . . .193
Power save mode . . . . . . . . . . . . . . . . . . . . . . .54
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . .23
POWER switch . . . . . . . . . . . . . . . . . . . . . . . . .26
Powered IS . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Pre-recording mode . . . . . . . . . . . . . . . . . . . . .121
R
Real-time proxy transfer . . . . . . . . . . . . . . . . . .188
Rec run (time code) . . . . . . . . . . . . . . . . . . . . . .90
*
only
243
S
U
USB terminal . . . . . . . . . . . . . . . . . . . . . . . . . 171
User bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
User memo . . . . . . . . . . . . . . . . . . . . . . . . . . 111
V
Vectorscope . . . . . . . . . . . . . . . . . . . . . . . . . 109
Video configuration . . . . . . . . . . . . . . . . . . . . . 55
Video output configuration . . . . . . . . . . . . . . . 159
Video scopes . . . . . . . . . . . . . . . . . . . . . . . . . 108
Viewfinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Y
P
O
Safe area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Saving clips to a computer . . . . . . . . . . . . . . . .168
Scan reverse recording . . . . . . . . . . . . . . . . . .141
SD card
Compatible SD cards . . . . . . . . . . . . . . .38
Initializing . . . . . . . . . . . . . . . . . . . . . . . .41
Inserting/Removing . . . . . . . . . . . . . . . . .40
Shooting frame rate . . . . . . . . . . . . . . . . . . . . .120
Shot marks . . . . . . . . . . . . . . . . . . . . . . .110, 157
Shoulder strap . . . . . . . . . . . . . . . . . . . . . . . . . .36
Shutter speed . . . . . . . . . . . . . . . . . . . . . . . . . .58
Slow & fast motion recording mode . . . . . . . . .120
Specifications . . . . . . . . . . . . . . . . . . . . . . . . .235
Status screens . . . . . . . . . . . . . . . . . . . . . . . . .209
Synchronization* . . . . . . . . . . . . . . . . . . . . . . . .94
C
Time code synchronization* . . . . . . . . . . . . 95, 96
TIME CODE terminal* . . . . . . . . . . . . . . . . . 95, 96
Tripod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 218
Turning the camcorder on/off . . . . . . . . . . . . . . 26
T
Tally lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . .208
Terminal covers . . . . . . . . . . . . . . . . . . . . . . . . .36
Time code . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
W
Waveform monitor . . . . . . . . . . . . . . . . . . . . . 108
White balance . . . . . . . . . . . . . . . . . . . . . . . . . 69
Wide DR . . . . . . . . . . . . . . . . . . . . . . . . 132, 135
Wireless controller . . . . . . . . . . . . . . . . . . . . . . 44
X
XF Utility (download) . . . . . . . . . . . . . . . . . . . . 168
Z
Zebra pattern . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Soft zoom control . . . . . . . . . . . . . . . . . 79
*
only
English
Recording
Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Photos . . . . . . . . . . . . . . . . . . . . . . . . .195
Simultaneous MXF+MP4 recording . . . .123
Relay recording . . . . . . . . . . . . . . . . . . . . . . . . .42
Remote controller . . . . . . . . . . . . . . . . . . . . . . .45
Remote operation . . . . . . . . . . . . . . . . . . . . . . .44
REMOTE terminal . . . . . . . . . . . . . . . . . . . . . . .45
Resetting all camcorder settings . . . . . . . . . . .208
Resolution (frame size) . . . . . . . . . . . . . . . . . . . .55
Reviewing a recording . . . . . . . . . . . . . . . . . . .116
Running mode (time code) . . . . . . . . . . . . . . . . .90
USA
&N
Z
CANON PROFESSIONAL DIGITAL VIDEO EQUIPMENT LIMITED WARRANTY FOR PRODUCTS
PURCHASED IN THE UNITED STATES
244
The limited warranty set forth below is given by Canon U.S.A., Inc. ('Canon USA') with respect to Canon Professional Digital Video Equipment (the
'Equipment') packaged with this limited warranty and purchased in the United States. This limited warranty is only effective upon presentation of your Bill
of Sale or other proof of purchase. The Equipment is warranted to the original end-user purchaser, when delivered in new condition in its original
container, under normal use against defective materials or workmanship as follows:
Parts: Defective parts will be exchanged for new parts or comparable rebuilt parts for a period of ONE YEAR from the date of original purchase.
Labor: For a period of ONE YEAR from the date of original purchase, labor will be provided free of charge by Canon USA's factory service centers or
designated service facilities located in the United States.
When returning Equipment under this warranty, you must pre-pay the shipping charges, and you must enclose a copy of the Bill of Sale or other proof of
purchase with a complete explanation of the problem. During the ONE-YEAR warranty period, repairs will be made and the Equipment will be returnshipped to you free of charge. For repairs after the warranty period is over, you will be given an estimate of the cost of repair and an opportunity to
approve or disapprove of the repair expense before it is incurred. If you approve, repairs will be made and the Equipment will be returned to you at your
risk and expense. If you disapprove, we will return-ship the Equipment to you at no charge to you to an address within the United States.
This limited warranty only applies if the Equipment is used in conjunction with compatible computer equipment and compatible software, as
to which items Canon USA will have no responsibility. Canon USA shall have no responsibility under this limited warranty for use of the
Equipment in conjunction with incompatible peripheral equipment and/or incompatible software. Non-Canon brand peripheral equipment and
software which may be distributed with, or factory loaded on, the Equipment, are sold 'AS IS' without warranty of any kind by Canon USA,
including any implied warranty regarding merchantability or fitness for a particular purpose. The sole warranty with respect to such nonCanon brand items is given by the manufacturer or producer thereof. If the Equipment contains a hard disk drive, Canon USA recommends
that data stored on that drive be duplicated or backed up to prevent its loss in the event of failure or other malfunction of such drive.
Y
P
O
In order to obtain warranty service, please contact the authorized Canon retail dealer from whom you purchased the Equipment or contact the CANON
INFORMATION CENTER AT 855-CINE-EOS (855-246-3367) or on the Internet at pro.usa.canon.com/support. You will be directed to the nearest
service facility for your Equipment.
This Limited Warranty covers all defects encountered in normal use of the Equipment and does not apply in the following cases:
A. Loss or damage to the Equipment due to abuse, mishandling, accident, improper maintenance, use of non-Canon accessories or failure to follow
operating, maintenance or environmental instructions prescribed in Canon USA's user's manual;
B. If the Equipment is defective as a result of leaking batteries, sand, dirt or water damage;
C. If defects or damages are caused by the use of parts or supplies (other than those sold by Canon USA) that cause damage to the Equipment or that
cause abnormally frequent service calls or service problems;
D. If defects or damages are caused by service other than Canon USA's factory service centers or authorized service facilities;
E. Any internal modification to product hardware or firmware;
F. Any applicable fee for Maintenance of the Equipment;
G. If the Equipment has had its serial number or dating altered or removed.
C
This Limited Warranty does not apply to Equipment purchased outside the United States. This Limited Warranty does not apply to accessories or
consumables for the Equipment, which are sold "AS IS", without warranty of any kind by Canon USA. Please retain this warranty card and your Bill of Sale
as a permanent record of your purchase. This card ensures that you are contacted promptly should there be a safety inspection, modification or product
recall under applicable laws or regulations.
NO IMPLIED WARRANTY, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLIES TO THIS EQUIPMENT AFTER THE
APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTY (EXCEPT AS MENTIONED ABOVE) GIVEN BY ANY PERSON, FIRM OR CORPORATION
WITH RESPECT TO THIS EQUIPMENT SHALL BIND THE UNDERSIGNED (SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU). CANON USA SHALL NOT BE LIABLE FOR LOSS OF
REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA,
INCLUDING WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE EQUIPMENT'S HARD DRIVE, OR ANY OTHER SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE EQUIPMENT, REGARDLESS OF THE LEGAL
THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON USA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL
RECOVERY OF ANY KIND AGAINST CANON USA BE GREATER THAN THE PURCHASE PRICE OF THE EQUIPMENT SOLD BY CANON USA AND
CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY
TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE, MISUSE OR INABILITY TO USE THE EQUIPMENT
NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CANON USA (SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU).THIS WARRANTY SHALL NOT EXTEND TO ANYONE OTHER
THAN THE ORIGINAL PURCHASER OF THIS EQUIPMENT OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
CANON U.S.A., INC.
CANADA
CANON PROFESSIONAL DIGITAL VIDEO EQUIPMENT LIMITED WARRANTY FOR PRODUCTS
PURCHASED IN CANADA
This limited warranty only applies if the Equipment is used in conjunction with compatible computer equipment and compatible software, as to
which items Canon Canada will have no responsibility. Canon Canada shall have no responsibility under this limited warranty for use of the
Equipment in conjunction with incompatible peripheral equipment and/or incompatible software. Non-Canon brand peripheral equipment and
software which may be distributed with, or factory loaded on, the Equipment, are sold 'AS IS' without warranty of any kind by Canon Canada,
including any implied warranty or condition regarding merchantability or fitness for a particular purpose. The sole warranty with respect to such
non-Canon brand items is given by the manufacturer or producer thereof. If the Equipment contains a hard disk drive, Canon Canada recommends
that data stored on that drive be duplicated or backed up to prevent its loss in the event of failure or other malfunction of such drive.
Y
P
O
In order to obtain warranty service, please contact the authorized Canon retail dealer from whom you purchased the Equipment or contact the CANON PROFESSIONAL
SERVICE CENTRE 1-800-667-2666 or on the Internet at www.canon.ca/pro. You will be directed to the nearest service facility for your Equipment.
This Limited Warranty covers all defects encountered in normal use of the Equipment and does not apply in the following cases:
A. Loss or damage to the Equipment due to abuse, mishandling, accident, improper maintenance, use of non-Canon accessories or failure to follow
operating, maintenance or environmental instructions prescribed in Canon Canada's user's manual;
B. If the Equipment is defective as a result of leaking batteries, sand, dirt or water damage;
C. If defects or damages are caused by the use of parts or supplies (other than those sold by Canon Canada) that cause damage to the Equipment or
that cause abnormally frequent service calls or service problems;
D. If defects or damages are caused by service other than Canon Canada's factory service centers or authorized service facilities;
E. Any internal modification to product hardware or firmware;
F. Any applicable fee for Maintenance of the Equipment;
G. If the Equipment has had its serial number or dating altered or removed.
C
This Limited Warranty does not apply to Equipment purchased outside Canada. This Limited Warranty does not apply to accessories or consumables for
the Equipment, which are sold "AS IS", without warranty of any kind by Canon Canada. Please retain this warranty card and your Bill of Sale as a
permanent record of your purchase. This card ensures that you are contacted promptly should there be a safety inspection, modification or product recall
under applicable laws or regulations.
NO IMPLIED WARRANTY OR CONDITION, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLIES TO THIS
EQUIPMENT AFTER THE APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTY (EXCEPT AS MENTIONED ABOVE) GIVEN BY ANY PERSON,
FIRM OR CORPORATION WITH RESPECT TO THIS EQUIPMENT SHALL BIND THE UNDERSIGNED (SOME PROVINCES DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY OR CONDITION LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU). CANON
CANADA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE
CHARGES, LOSS OR CORRUPTION OF DATA, INCLUDING WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE EQUIPMENT'S
HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE
EQUIPMENT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON CANADA HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST CANON CANADA BE GREATER THAN THE PURCHASE PRICE OF
THE EQUIPMENT SOLD BY CANON CANADA AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK
AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE,
MISUSE OR INABILITY TO USE THE EQUIPMENT NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CANON CANADA (SOME PROVINCES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU).
THIS WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS EQUIPMENT OR THE PERSON FOR WHOM
IT WAS PURCHASED AS A GIFT.
This warranty gives you specific legal rights, and you may also have other rights which vary from province to province.
CANON CANADA INC.
245
English
The limited warranty set forth below is given by Canon Canada Inc. ('Canon Canada') with respect to Canon Professional Digital Video Equipment (the
'Equipment') packaged with this limited warranty and purchased in Canada. This limited warranty is only effective upon presentation of your Bill of Sale or
other proof of purchase. The Equipment is warranted to the original end-user purchaser, when delivered in new condition in its original container, under
normal use against defective materials or workmanship as follows:
Parts: Defective parts will be exchanged for new parts or comparable rebuilt parts for a period of ONE YEAR from the date of original purchase.
Labor: For a period of ONE YEAR from the date of original purchase, labor will be provided free of charge by Canon Canada's factory service center or
designated service facilities located in Canada.
When returning Equipment under this warranty, you must pre-pay the shipping charges, and you must enclose a copy of the Bill of Sale or other proof of
purchase with a complete explanation of the problem. During the ONE-YEAR warranty period, repairs will be made and the Equipment will be returnshipped to you free of charge. For repairs after the warranty period is over, you will be given an estimate of the cost of repair and an opportunity to
approve or disapprove of the repair expense before it is incurred. If you approve, repairs will be made and the Equipment will be returned to you at your
risk and expense. If you disapprove, we will return-ship the Equipment to you at no charge to you to an address within Canada.
Canon Inc.
1
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
ASIA and HONG KONG, S.A.R.
Canon Hongkong Company Ltd
19/F, The Metropolis Tower, 10 Metropolis Drive,
Hunghom, Kowloon, Hong Kong
+852 3191 2333,
+852 2428 3963
CANADA http://www.canon.ca/pro
CANON CANADA INC.
❖ Professional Product Support /
Soutien des produits professionnels
(800) 667-2666
MÉXICO http://www.canon.com.mx
CANON MEXICANA, S DE RL DE CV
52 (55) 5249-4905
USA
CANON U.S.A., INC. http://pro.usa.canon.com
http://pro.usa.canon.com/support
(855) CINE-EOS (855-246-3367)
(USA only)
CENTRO Y SURAMÉRICA http://www.cla.canon.com
CANON LATIN AMERICA, INC.
Y
P
O
Visit your local Canon Web site to download the latest version of this Instruction Manual.
Consultez votre site Web Canon local pour télécharger la version la plus récente de ce manuel d'instructions.
Para descargar la última versión de este manual de instrucciones, visite nuestro sitio web local de Canon.
C
© CANON INC. 2014
PUB. DIM-1104-000A