INSTRUCTION MANUAL Ver 1.2

INSTRUCTION MANUAL

Ver 1.2

Megapixel PTZ Camera

HC0212NOV20

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN THE COVERS.

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONAL

This lightning flash with arrowhead symbol is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

This Device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interface, and

(2) This device must accept any interference received, including interference that may cause undesired operations.

Speed Dome Camera Instruction Manual

2/65

NOTICE

Important Safety Guide

1. Read, heed and follow all the Instructions

Read all the safety and operating instructions before using the product.

2. Keep this manual

Keep this manual for reference in future.

3. Attachments / Accessories

Use only the attachments or accessories specified by the manufacturer.

4. Installation z

Do not install near any heat resources such as radiators, heat registers, stoves, or other appratus including amplifiers that product heat. Improperly installed product may fall, cause serious injury to a child or adult and damage the product. z

Do not block any ventilation holes or openings. Install in accordance with the manufacturer’s instructions. z

Use only with the cart, stand, tripod, bracket, mounting devices, or table specified by the manufacturer. z

Installation should be done only by qualified personnel and conform to all the instructions by the manufacturer. z

Refer all servicing to qualified service personnel. z

Unless the product is specifically marked as IP67, more than IP67 or confirmed by the manufacturer, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. z

Do not load on the product. z

Use stainless steel hardware to fasten the mount. z

To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply sealant properly around holes. z

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other that contained in the operationg instructions unless you are qualified to do so. z

Use only replacement parts specified by the manufacturer.

5. Power source

This product should be operated only from the type of the power source indicated on the marking label. It is mandatorily recommended to use a UPS in order to be prepared for

a power failure.


3/65

NOTICE

Caution

Operating

z

Before using, make sure that the power supply and others are properly installed. z

While operating, if any abnormal condition or malfunction is observed, stop using the product immediately and then contact your local dealer.

Handling

z

Do not disassemble or tamper with the parts inside the product. z

Do not drop or subject the product to shock and vibration as this can damage the product. z

Care must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin the quality of the product.

Installation and Storage

z

Do not install the product in areas of extreme temperature, which exceed the allowable range. z

Avoid installing in humid or dusty places. z

Avoid installing in places where radiation is present. z

Avoid installing in places where there are strong magnetic fields and electric signals. z

Avoid installing in places where the product would be subject to strong vibrations.


4/65

TABLE OF CONTENTS

①

Introduction

Model Code 6

Features 7

Package Components 10

Main Part Description 11

②

Installation

DIP Switch Setup 12

Installation with Ceiling Mount Bracket 14

Installation with Wall Mount Bracket 15

Wiring and Cabling 16

③

Operation

Check Point before Operation 20

Check Points for Preset and Pattern Function before Operation 20

OSD Menu 21

Reserved Preset (Hot Keys) 21

Preset 22

Swing 22

Pattern 23

Group 24

Other Functions 24

OSD Display 26

④

OSD Menu

Quick Programming Guide 27

Video Setup 27

Privacy Mask Setup 37

PTZ Setup 39

Action Setup 41

Preset Setup 42

Swing Setup 44

Pattern Setup 45

Group Setup 47

Alarm Trigger Setup 48

Schedule Setup 49

OSD Setup 50

System Setup 52

Time Setup 55

Password Setup 56

⑤

Specifications 57

Dimension 65


5/65

Model Code

H C - N 2 0 S W - S

Option

S : HD-SDI output

Mount Bracket

W : Wall Mount

C : Ceiling Mount

Zoom

30S : Optical x30, 2M pixels

20S : Optical x20, 2M pixels

30T : Optical x30, 1.3M pixels

20T : Optical x20, 2M pixels

19T : Optical x19, 1.3M pixels

20W : Optical x20, 2M pixels

Composite Video Signal

N : NTSC

P : PAL

Series

HC: Megapixel PTZ (HD-SDI)

INTRODUCTION

1


6/65

INTRODUCTION

1

Features

Powerful Zoom Camera & Setup Options

z

Image Sensor : 1/2.8" Exmor CMOS Image Sensor, 3 Mega pixels (30S model)

1/2.8" Exmor CMOS Image Sensor, 3 Mega pixels (20S model)

1/4" PS CMOS Image Sensor, 1.3 Mega pixels (30T model)

1/3" PS CMOS Image Sensor, 2 Mega pixels (20T model)

1/3" PS CMOS Image Sensor, 1.3 Mega pixels (19T model)

1/3" Panasonic CMOS Image Sensor, 2 Mega pixels (20W model) z

Zoom : ×30 Optical Zoom, ×12 Digital Zoom (30S model)

×20 Optical Zoom, ×12 Digital Zoom (20S model)

×30 Optical Zoom, ×12 Digital Zoom (30T model)



×20 Optical Zoom, ×12 Digital Zoom (20W model) z

Day & Night, Privacy Mask z

WDR function (30S, 20S, 30T, 20W models) z

HLC function (30T, 20T, 19T models) z

NR (Noise Reduction) Function z

Defog Function (20W model) z

Image Stabilization Function (30S, 30T, 20T, 19T models) z

Various Focus Mode : Auto-Focus, Manual Focus, Semi-Auto Focus z

Various Setup Options in OSD Menu.

HD-SDI and Composite Video Output

z

Raw(Non-Compressed) Digital HD-SDI(High Definition Serial Digital Interface) Output

(HDcctv v1.0, 1.485Gb/s, SMPTE 292M Standard) z

HD-SDI Video Transmission over Coaxial Cable. z

Simultaneous HD-SDI and Analogue(Composite) Video Output

Powerful Pan/Tilt Functions

z

MAX. 500 °/sec High Speed Pan/Tilt Motion z

With the Vector Drive Technology, Pan/Tilt motions are accomplished along the shortest path. As a result, the time to target view is remarkably short and the video on the monitor is very natural in monitoring. z

With the Micro-Stepping Control Technology, the video looks very natural at high zoom magnification during a jog operation on a controller since the camera can be controlled by 0.05

°/sec. Hence it is very easy to make the camera focus on desired target views at high zoom magnification. Additionally it is easy to make the camera focus on desired positions with zoom-proportional pan/tilt movement.


7/65

INTRODUCTION

1

RTC(Real Time Clock) Function

z

Date and Time can be configured for Schedule Function z

With Backup Battery Function, Date and Time configuration should be kept up for a while, even though power is off

Preset, Pattern, Swing, Group, Schedule, Privacy Mask and More…

z MAX. 209 Presets are programmable and each preset can have its own parameter values independently from the other presets.

For an example, refer to the below table.

Preset No. White Balance Auto Exposure

•••

Label Remarks

Preset 1 Case A Case 3 “ENTRANCE”

Preset 2

•••

Case C Case 5 “WAREHOUSE”

Preset 95 − − −

•••

Preset 255 Case K Case 9 “TERRACE” z

MAX. 10 sets of Swing are programmable. This function is that a camera moves repetitively between two preset positions at programmed speeds. z

MAX. 4 Patterns are programmable. This function is that a camera memorizes the path

(mostly curve path) by the joystick of the controller and revives the trajectory operated by the joystick as closely as possible. z

MAX. 8 sets of Group are programmable. This function is that a camera memorizes the combination of Presets, Pattern and/or Swings sequently and runs Presets, Pattern and/or Swings repetitively. A Group can be combined upto 40 functions with any of

Preset/Pattern/Swing. z

MAX. 8 Privacy Masks are programmable, not to intrude on any other’s privacy. z MAX. 8 sets of Schedule are programmable. This function is that a camera runs a function such as Preset, Pattern, Swing or Group at an assigned time. Also this function can be run periodically by pre-defined schedules.

PTZ(Pan/Tilt/Zoom) Control

z

With the RS-485 communication connection, MAX. 255 units of cameras can be connected to a single controller. z

Pelco-D or Pelco-P protocols can be selected as a control protocol in the current firmware version.


8/65

INTRODUCTION

1

OSD(On Screen Display) Menu

z

OSD menu is provided to display the status of camera and to configure the functions interactively. A P assword can be configured in OSD menu and OSD menu can be protected.

z

The information such as Camera ID, Pan/Tilt Angle, Time/Date, Alarm Input and Preset information is displayed on screen.

Alarm In/Out Function

z

3 alarm sensor inputs and 1 alarm sensor outputs are available. z

Alarm sensor input is decoupled with photo-couplers to avoid external electric noise and shock perfectly. z

Both of N.O.(Normal Open) sensors and N.C.(Normal Close) sensors can be used and the signal range of the sensor input is from DC 5.0V to 12.0V for various applications. z

The camera can be set to move to a Preset position or to run functions such as Pattern,

Swing and Group when there are external sensor activations. Also “Post Alarm” function is possible, which is supposed to activate after user-defined time period and sequentially in succession to the action by external sensor activations.

Reserved Presets(Hot Keys)

z

Most camera setup options can be set up easily and directly with the reserved presets

(Hot Keys), without entering into OSD menu. For more information, refer to “Reserved

Presets(Hot Keys)” in this manual.

Dual Power Input

z

The input power source is DC 12 V or AC 24 V.

Perfect Outdoor Environment Compatibility and Easy Installation

z

The fans and heaters are built-in in the camera for cold and hot temperature environment. Also idealistic mechanical design protects the camera from water and dust. (IP67 when installed properly with wall mount bracket only / Only for outdoor models) z

It is easy to install and repair the camera.


9/65

Package Component

Product & Accessories

INTRODUCTION z

Main Body & Surface Mount Bracket

Brackets (Optional)

Manual z

Default Accessories

[Main Cable, I/O Cable ,Wrench, Owner’s Manual]

1

z

Wall Mount Bracket

[Screws :

TORX Machine M4 ×L18

, Hex Lag

#14

×50] z

Ceiling Mount Bracket

[Screws :

TORX Machine M4 ×L18

, Anchor Bolt

3/8"

×70]


10/65

Main Part Description

INTRODUCTION

1

DIP Switch

Mounting Screw Hole

Drop Prevention Spring

Main Connector

BNC Connector for SDI

Sensor I/OPort

Dome Cover z z

Dome Cover

DIP Switch z

Drop Prevention

Spring

Do not detach the protection vinyl from the dome cover before finishing all the installation process to protect the dome cover from scratches or dust.

Used to set up camera IDs and protocols.

This part keeps the camera from dropping during installation and maintenance. After install the Bracket, please, hang the spring to the drop prevention hook of main body as shown in picture for further tasks. z

Mounting Screw Hole Used to assemble the main body with a bracket with screws.

z

Main Connector z

BNC Connector

for SDI z

Sensor I/O Port

Used for the power wire, the composite video signal and the RS-

485 communication cable connection.

Used for the HD-SDI video signal connection.

Used for the sensor in/out connection.


11/65

INSTALLATION

2

DIP Switch Setup

Before installing the camera, set up the DIP switch to configure the camera ID and the communication protocol.

Camera ID Setup

ON

ON

1 2 3 4 5 6 7 8 z

ID numbers of cameras are set up with binary numbers.

See the examples shown below.

Pin 1 2 3 4 5 6 7 8

Binary Value 1 2 4 8 16 32 64 128 ex) ID=5 ex) ID=10 on off on off off off off off off on off on off off off off z

The camera ID range is “1~255”. Camera ID must not be

“0”! z

The factory default of the camera ID is “1”. z

Match the camera ID with the Cam ID setting of your DVR or Controller to control the camera. z

If you are connecting a single camera to a controller, terminate the camera. When connecting more than one camera to a single controller, terminate the last camera on the communication line. The last camera means the camera farthest in cable length from the controller. z

Note that the total length of the communication cable between a controller and the camera(s) on the same communication line must be less than 1.2Km.


12/65

INSTALLATION

Communication Protocol Setup z

Select an appropriate Protocol with the DIP switch combination.

ON

ON

Switch Mode

Protocol

1 2 3 4

P0

(Pin 1)

P1

(Pin 2)

P2

(Pin 3)

2

OFF OFF OFF

ON OFF OFF

OFF ON OFF

PELCO-D, 9600 bps

ON ON OFF PELCO-P, 9600 bps

Others Reserved z

Match the camera protocol with the camera protocol in the setting of your DVR or controller to control the camera. z

Adjust the DIP switch after turning off the camera. If you changed the camera protocol by changing the DIP S/W, the change will be effective after you reboot the camera. z

The factory default protocol is “Pelco-D, 2400 bps”.


13/65

INSTALLATION

2

Installation with Ceiling Mount Bracket

①

Remove the ceiling tile from the ceiling and cut a hole whose diameter is

30~40mm on the ceiling tile to pass the wire(s) and cable(s) through to the upside of the ceiling. (In case of the wiring and cabling through the mounting surface only) Then prepare the ceiling mount bracket. Pull the wire(s) for the system as below. (Anchor Bolt 3/8" ×70)

②

Hook up “Drop Prevention Spring” on main body to prevent camera from unexpected drop and pull the wire(s) and cable(s) for the system as below.

Spring Wire Hook

③

Line up the mold lines and assemble main body to mount adaptor and turn it.

And assemble the main both with the camera mount adaptor with the 3 screws.

(

TORX SCREW M4 ×18

).

④

Screw the dome cover to the main body and remove the protection vinyl from the dome cover.

END

START

Important Notice z

Before starting the installation, make sure that the Camera ID and Protocol are set up properly. z

To adjust the installation height from the mounting surface, the pipe and coupler should be needed between the surface mount part of the ceiling mount bracket and the camera mount part of the ceiling mount bracket. Note that they are not supplied by the manufacturer.


14/65

INSTALLATION

2

Installation with Wall Mount Bracket

①

Make a hole whose diameter is 30~40mm on the mounting surface to pass the wire(s) and cable(s) through the mounting surface. (In case of the wiring and cabling through the mounting surface only) Then prepare the wall mount bracket. Pull the wire(s) and cable(s) for the system as below. Attach the wall mount bracket to the mounting surface. (Hex Lag #14

×50)

②

Hook up “Drop Prevention Spring” on main body to prevent camera from unexpected drop and pull the wire(s) and cable(s) for the system as below.

Spring Wire Hook

③

Line up the mold lines and assemble main body to mount adaptor and turn it.

And assemble the main both with the camera mount adaptor with the 3 screws.

(

TORX SCREW M4 ×18

).

④

Screw the dome cover to the main body and remove the protection vinyl from the dome cover.

END

START

Important Notice z

Before starting the installation, make sure that the Camera ID and Protocol are set up properly.


15/65

Wiring and Cabling

INSTALLATION

BNC CABLE

(HD-SDI)

POWER

MONITOR for HD-SDI

MAIN CABLE

BNC(Composite)

MONITOR

RS-485

I/O CABLE

CONTROLLER / DVR

SENSOR I/O

IR

SENSOR

DOOR

SWITCH

Port Description z

Main Cable

Port Pin Number (RJ45)

1

Connector / Wire Color

5 Red

3 Yellow

7 Orange

6,8 White z

I/O Cable

Port Pin Number (RJ25) Wire Color

1 Blue

2 Yellow

3 Green

4 Red

5 Black

6 White

Signal

Composite Video +

RS-485 −

Power −

Signal

IN 1 −

OUT B

2


16/65

INSTALLATION

2

Power Description z

Carefully check the voltage and current capacity of the rated power.

Power Input

DC12V Input

AC24V Input

Input Voltage Range

DC 11V ~ 18V

AC 17V ~ 29V

Current Consumption

1.8A

2.0A

z

For the DC input, be careful with the polarity of DC power. The system should be permanentally damaged by wrong DC input. z

In case that the length of the DC power wire is very long, there may be voltage drop and the syatem may not work properly. Make the length of the power wire as short as possible.

RS-485 Communication z

For PTZ control, connect the cable(s) to your keyboard or DVR. To connect multiple cameras to a single controller, RS-485 communication should be connected in parallel as shown below. If you are connecting a single camera to a controller, terminate the camera.

When connecting more than one camera to a single controller, terminate the last camera on the communication line. The last camera means the camera farthest in cable length from the controller. Note that the total length of the communication cable between a controller and the camera(s) on the same communication line must be less than 1.2Km.

CONTROLLER / DVR

RS-485

+

-

+

-

#1

+

-

#2

+

-

#n


17/65

INSTALLATION

2

HD-SDI Video Output z

Transmission Distance of HD-SDI Video Signal should be variable by cables. There may be no video on a monitor due to cable quality or specification. Use proper BNC Coaxial

Cables after considering transmission distance. z

Your reference, see the below table. It shows transmission distances by cables.

Cable Type

RG11 14AWG

Belden 1694A 18AWG

RG6 18AWG (5C-HFBT)

RG59 20AWG

RG59 23AWG

3C2V 25AWG

Transmission Distance

330 Meter

230 Meter

210 Meter

150 Meter

110 Meter

90 Meter


18/65

INSTALLATION

2

Alarm Input

Internal

IN COM+

IN 1-

IN 3-

Sensor 1

Sensor 3

+

+

+5V~12V

+

-

-

-

Before connecting sensors, check driving voltages and output signal types of the sensors.

Since output signal types of the sensors are divided into Open Collector type and

Voltage Output type in general, the wiring must be done properly after considering those types.

Signal Description

IN COM+ The electric power source to drive input circuit. Connect the (+) wire of electric power source to drive the Sensors to this port as shown in the above circuit.

IN1 -, IN2 -, IN3 - Connect the outputs of sensors to each port as shown in the above circuit.

If you want to use Alarm Input, the types of sensors must be selected in OSD menu. The sensor types are divided into Normal Open and Normal Close. If wrong sensor types are selected, alarms should be activated reversely to sensor inputs.

~

Normal Open Output Voltage is high state when sensor is activated

~

Normal Close Output Voltage is high state when sensor is not activated

Relay Output

Internal

AC or DC

OUT 1

LOAD

The maximum loads are as follows.

Power Type DC Power

Maximum Load MAX. DC 24V, 1A

AC Power

MAX. AC 125V, 0.5A


19/65

OPERATION

3

Check Points before Operation

z

Before turning on the system, check if the wire(s) and cable(s) are connected properly. z

Check if the camera ID on the controller is properly selected. The camera ID must be identical to that of the target camera. The camera ID can be checked by reading the DIP switch of the camera or on OSD. z

If your controller supports multi-protocols, the protocol must be changed to match to that of the camera. z

Adjust the DIP switch after turning off the camera. If you changed the camera protocol by changing the DIP S/W, the change will be effective after you reboot the camera. z

Since the operation method can be different by controllers, refer to your controller manual if the camera can not be controlled properly. The operation of this manual is based on the standard Pelco® Controller.

Check Points for Preset and Pattern Function before Operation

z

Check fully how to operate preset function and pattern function with your controller or DVR in advance to operate the camera functions when using a controller or a DVR. z

Refer to the following table when using standard Pelco® protocol controllers.

< Go Preset > Input [Preset Number] and press [Preset] button shortly.

< Set Preset > Input [Preset Number] and keep pressing [Preset] button for more than 2 seconds.

< Run Pattern > Input [Pattern Number] and press [Pattern] button shortly.

< Set Pattern > Input [Pattern Number] and keep pressing [Pattern] button for more than 2 seconds.

z

If your controller or DVR has no pattern button or function, use the Hot Keys with preset numbers. For more information, refer to “Reserved Presets(Hot Keys)” in this manual.


20/65

OPERATION

3

OSD Menu

z

Function With OSD menu, the system can be properly configured for each application. z

Entering into OSD Go Preset [95]

Reserved Presets (Hot Keys)

z

Description Some Preset numbers are reserved to change some parameters without entering into

OSD menu. z

Hot Keys Go Preset [95] : Entering into OSDmenu

Go Preset [151~158] : Running Group Function 1 ~ 8

Go Preset [161]

Set Preset [161]

Go Preset [167]

: Turning off Relay Output

: Turning on Relay Output

: Setting Zoom Proportional Function to ON

Set Preset [167]

Go Preset [170]

Go Preset [171]

: Setting Zoom Proportional Function to OFF

: Setting Camera BLC Mode to OFF

: Setting Camera BLC Mode to ON

Go Preset [174]

Go Preset [175]

Go Preset [176]

Go Preset [177]

Go Preset [178]

Go Preset [179]

Go Preset [190]

Go Preset [191]

: Setting Camera Focus Mode to AUTO

: Setting Camera Focus Mode to Manual

: Setting Camera Focus Mode to SEMI-AUTO

: Setting Day & Night Mode to AUTO

: Setting Day & Night Mode to NIGHT

: Setting Day & Night Mode to DAY

: Setting OSD Display Mode to AUTO (Except Privacy Mask)

: Setting OSD Display Mode to OFF (Except Privacy Mask)

Go Preset [193]

Go Preset [194]


: Setting all Privacy Mask Display to OFF

: Setting all Privacy Mask Display to ON

21/65

OPERATION

3

Preset

z

Function

MAX. 209 presets can be configured except the Reserved Presets (Hot

Keys).

Camera parameters such as White Balance, Auto Exposure and others can be set up independently and each preset can have its own parameter values independently from the other persets. When setting up presets with a controller, Label should be blank and Video settings should be set to "GLOBAL" as the default. To change the parameters, enter into OSD menu.

Set Preset [1~255] z

Setting Presets z

Running Presets Go Preset [1~255] z

Deleting Presets To delete Presets, enter into OSD menu.

Swing

z

Function This function is that the camera moves repetitively between two preset positions at programmed speeds. When a swing function runs, the camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW(Clockwise) direction. Then the camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in CCW(Counterclockwise) direction.

1

CW

Di rec tio n tio n

2nd Preset

1st Preset

2

CC

W

Dir ec

In case that the preset assigned as the 1st point and the preset assigned as the 2nd point are same, the camera turns on its axis by

360

° in CW(Clockwise) direction and then it turns back on its axis by

360 ° in CCW(Counterclockwise) direction. The Swing speed is defined from 10

°/sec to 180°/sec.

To set Swing, enter into OSD menu. z

Setting Swings z

Running Swings Method 1) <Run Pattern> [Swing NO. + 10]

Method 2) <Go Preset> [Swing NO. + 140] z

Deleting Swings To delete Swings, enter into OSD menu. ex) Run Swing 3 : <Run Pattern> [13] ex) Run Swing 3 : <Go Preset> [143]


22/65

Pattern

z

Function

OPERATION

3

z

Setting Patterns

This function is that the camera memorizes the path (mostly curve path) by the joystick of the controller and revives the trajectory operated by joystick as closely as possible.

MAX. 4 Patterns are programmable and Maximum 768 communication commands can be programmed in a pattern.

A Pattern can be created by the following methods.

Method 1) <Set Pattern> [Pattern NO.]

{

The Pattern programming window appears on the monitor as below.

EDIT PATTERN ] 90%

PATTERN RECORDING

[NEAR : SAVE / FAR : CANCEL]

{

The movement by Joystick can be memorized in a pattern.

{

To save the recording, press NEAR key and to cancel, press

FAR key.

Method 2) Programming in OSD Menu : See the section “How to use OSD Menu”. z

Running Patterns Method 1) <Run Pattern> [Pattern NO.]

Method 2) <Go Preset> [Pattern NO. + 130] ex) Run Pattern 2 : <Run Pattern> [2] ex) Run Pattern 2 : <Go Preset> [132] z

Deleting Patterns To delete Patterns, enter into OSD menu.

Note) When the system memorizes Patterns, the commands are stored in the momories, not the positions of Pan/Tilt/Zoom. Hence there might be small differences between the original path and the revived path by path type of Patterns. Note that it is not a problem in position precision.


23/65

Group

z

Function

OPERATION

3

This function is that the camera memorizes the combination of

Presets, Pattern and/or Swings sequently and runs Presets, Pattern and/or Swings repetitively. MAX. 8 sets of Group are programmable.

Each group can have MAX. 40 actions which are the combination of

Preset, Pattern and Swing. Preset speed can be set up and the repeat number of Pattern & Swing can be set up in Group setup. Dwell time between actions can be set up also.

Dwell Time

Preset 1 Pattern 1 Swing 1

Max 40 Entities z

Setting Groups To set Groups, enter into OSD menu. z

Running Groups Method 1) <Run Pattern> [Group NO. + 20]

Method 2) <Go Preset> [Group NO. + 150] ex) Run Group 7 : <Run Pattern> [27] ex) Run Group 7 : <Go Preset> [157] z

Deleting Groups To delete Groups, enter into OSD menu.

Other Functions

z

Power Up Action This setting defines a specific activity (Preset, Pattern, Swing and

Group) to be performed in the event that the power to the camera is cycled. This function enables the user to resume, after turning on power, the last action being executed before turning off the power.

Most of actions such as Preset, Pattern, Swing and Group are available for this function but Jog actions are not available to resume. z

Auto Flip z

Parking Action

In case that tilt angle arrives at the top of tilt orbit(90°), zoom module camera turns on its axis by 180° at the top of tilt orbit and moves to opposite tilt direction (180°) to keep tracing targets.

This feature allows the camera to begin a specified operation after a programmed time of inactivity. This function makes the camera automatically run a pre-defined action if there is no command from controller for a pre-defined time period. “Wait Time” means how long a camera should wait for from the previous-last (most recent) command before running the pre-defined action. It can be set to 1 second ~ 3 hours.


24/65

OPERATION

3

z

Alarm Input 3 Alarm Inputs are available. When external sensors activate, the camera runs pre-defined actions such as Preset, Pattern, Swing and

Group. After the pre-defined time period passed, “Post Alarm” activates, which is pre-defined. Note that only the latest alarm input is effective when multiple sensors are activated at the same time. z

Schedule

8 Schedule are programmable. A camera runs functions such as Preset,

Pattern, Swing and Group at assigned times. After a pre-defined time passes, “Post Action” runs. Also this function can be run periodically by pre-defined schedules. A Period can be configured by

Once/Hourly/Daily/Weekly/Monthly

. z

Privacy Zone Mask Privacy Zone Mask allows a user to program 8 rectangulars that can not be viewed by the operator of the system. To protect others’ privacy, MAX. 8 Privacy Masks can be created on the arbitrary position to hide objects such as windows, shops or private house.

With the Spherical Coordinates system, powerful Privacy Zone Mask function is possible. A mask area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide. z

Password for OSD A protected.

[Important Notice] It is mandatorily recommended that a user must take a memo for a password before a user applies a password to a system. When a Password is forgotten, a unit can not be unlocked and

the unit is supposed to be shipped back to the manufacturer.

z

GLOBAL/LOCAL

Image Setup z

Semi-Auto Focus

WB(White Balance) and AE(Auto Exposure) can be set up independently for each preset. There are 2 modes, "Global" mode &

"Local" mode. The Global mode is that WB and AE are set up totally and simultaneously for all presets. The Global parameter setup can be done in "VIDEO" menu. The Local mode is that WB and AE are set up independently for each preset. Each Local parameter such as WB and AE activates correspondingly when the camera arrives at each preset position. During jog operation, Global WB/AE value should be applied. All Local WB/AE values do not change although Global

WB/AE value changes. The Local mode has the prior to the Global mode.

This mode automatically exchanges focus modes between Manual

Focus mode and Auto Focus mode by operation. Manual Focus mode activates in preset operation and Auto Focus mode activates during jog operation. With Manual mode at presets, Focus data is memorized in each preset in advance and the camera calls focus data in correspondence with presets as soon as the camera arrives at presets. It should shorten time to get focuses. The focus mode automatically changes to Auto Focus mode when jog operation starts.


25/65

OSD Display

OPERATION

3

LABEL12345 PRESET 001

Preset Label Acrtion Title

Time (Hour:Min:Sec)

Camera ID Date (Day/Mon/Year)

Alarm Information

PTZ Information

I:-2- O:1

CAM1 AM 00:00:00 01/JAN/2012 000/000/x001 z

P/T/Z Information Displays the pan/tilt positions and zoom magnification.

z

Camera ID Displays the selected Camera ID (Address).

z

Action Title Identfies Actions

"PRESET xxx"

"PATTERN x"

When Preset xxx is memorized or the camera reaches Preset xxx.

When Pattern x is in action.

"SWG ×-PRESET xxx" When Swing x is in action. Displays both of Swing number and Preset number.

"UNDEFINED" When a undefined function is called to run

Displays preset labels when the camera arrives at presets.

z

Preset Label z

Alarm Information Displays activated alarms. This information shows current state of

Alarm Inputs and Relay Outputs. If an Input point is ON state, it will show a number corresponding to each point. If an Input point is OFF state, '-' will be displayed.

Example) The point 2 & 3 of inputs are ON and Output is ON. z z

Time/Date

Heater Status

I:-23 O:1

Displays the current time and date.

Displays the Heater Status. If the Heater is OFF, the background of OSD is Blue color. If the Heater is ON, the background of OSD is Orange color.


26/65

OSD MENU

4

Quick Programming Guide

z

To move the cursor in the menu, use the joystick to the “Up/Down” direction or

“Left/Right” direction. z

To change a value of an item, use “Tele/Wide” of the joystick in the controller. z

The menu items with “>>” always have sub-menus. To move to submenu, use “Right” of the joystick. z

To go to the previous-upper level menus, use “Left” of the joystick z

On the item with “>”, use “Tele" of the joystick to execute.

Video Setup (30S, 20S model)

z

Focus Mode

VIDEO FOCUS MODE SEMIAUTO

PTZ WHITE BALANCE AUTO

ACTION - RED OFFSET 128

OSD - BLUE OFFSET 128

SYSTEM EXPOSURE MODE AUTO

INFORMATION - SHUTTER 1/60

- IRIS F5.6

- GAIN 0 dB

- BRIGHTNESS 10

BLC OFF

WDR OFF

AUTO DSS ON

APERTURE 12

DAY&NIGHT AUTO

DIGITAL ZOOM ON

IMAGE FLIP OFF

STABILIZATION OFF

PRIVACY MASK >>

HD-SDI RESOLUTION 1080p30

[AUTO/MANUAL/SEMIAUTO]

Sets camera Focus mode.

{

SEMIAUTO Mode

This mode automatically exchanges focus modes between Manual Focus mode and Auto Focus mode by operation. Manual Focus mode activates in preset operation and Auto Focus mode activates during jog operation


27/65

OSD MENU

4

With Manual mode at presets, Focus data is memorized in each preset in advance and the camera calls focus data in correspondence with presets as soon as camera arrives at presets. It should shorten time to get focuses .

Focus mode automatically changes to Auto Focus mode when jog operation starts. z

White Balance [AUTO/MANUAL]

Retains color balance over a color temperature range. In auto mode, this feature automatically processes the viewed image. In Manual mode, Red and Blue level can be set up manually. z z

Red Offset

Blue Offset

[0 ~ 255]

Adjusts the picture output in the red range.

[0 ~ 255]

Adjusts the picture output in the blue range. z

Exposure Mode [AUTO/MANUAL/SHUTTER/IRIS/BRIGHTNESS]

Set Auto Exposure mode. z

Shutter [1/1 ~ 1/10000]

If AE mode is set to SHUTTER mode or MANUAL mode, this can be set up.

For Flickerless function, set the shutter mode to 1/100 in NTSC, 1/20 in PAL.

z

Iris [CLOSE/F1.6~F14]

If AE mode is set to IRIS mode or MANUAL mode, this can be set up.

z

Gain z z z

Brightness

BLC

WDR

[-3dB ~ 28dB]

If AE mode is set to MANUAL mode, this can be set up.

[0 ~ 31]

If AE mode is set to BRIGHTNESS mode, this can be set up.

[ON/OFF]

Sets Backlight Compensation. If a bright backlight is present, the subjects in the picture may appear dark or as a silhouette. Backlight compensation enhances objects in the center of the picture. The camera uses the center of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out to white. The camera will adjust the iris so that the object in the sensitive area is properly exposed.

[OFF/ON]

The WDR(Wide Dynamic Range) is a function for dividing an image into several blocks and correcting blocked-up shadows and blown-out hightlights in accordance with the intensity diffrence. It enables you to obtain images in which portions ranging from dark to light can be recognized, even when capturing a subject with a large intensity difference that is backlit or includes extremely light portions.


28/65

OSD MENU

4

z z

Auto DSS

Aperture

[ON/OFF]

When set to ON, ensure that the slow shutter is set to automatically when the brightness drops. Effective only when the AE mode is set to AUTO.

The Auto DSS function is not abailiable in WDR mode.

[0 ~ 15]

Adjust the enhancement of the edges of objects in the picture. z

Day/Night z Digital Zoom [ON/OFF]

Sets the digital zoom functions to ON/OFF. If this is set to OFF, the optical zoom function runs but the zoom function stops at the end of optical zoom magnification. z

Image Flip

[AUTO/DAY/NIGHT]

Sets Day&Night mode.

[ON/OFF]

Sets System Image Flip Function to ON/OFF. When this function is set to ON, flipped images always come out. When the camera is installed as Desktop type, set to ON to get proper images. z

Stabilization [ON/OFF]

Compensates image vibrations by wind or others. The images with vibrations are compensated by Digital Zoom function and the image resolution with this function should be lower than normal image resolution when this function is turned on. This function is not supported on 20S model. z

HD-SDI

Resolution

NTSC

PAL

: [1080p30/1080i60/720p60/720p30]

: [1080p25/1080i50/720p60/720p30]

Sets the video resolution of HD-SDI. Match the resolution with the setting of monitor or DVR.

If there is no confirmation within 10 seconds by pressing the NEAR button, it is automatically restored to its previous configuration.


29/65

Video Setup (30T, 20T, 19T model)



ACTION

OSD

- RED OFFSET 105

- BLUE OFFSET 112

SYSTEM SHUTTER MODE ESC


IRIS MODE AUTO

- IRIS F1.6

GAIN MODE MEDIUM

- GAIN 0 dB

BRIGHTNESS 50

BACKLIGHT OFF

- LEVEL LOW

- COLOR 1

SENS-UP AUTO

- SENS-UP LIMIT X2

SSNR MEDIUM

SHARPNESS 12

DAY&NIGHT AUTO

[NEXT : MORE]

OSD MENU

4

VIDEO DIGITAL ZOOM ON

PTZ IMAGE FLIP OFF

ACTION STABILIZATION OFF

OSD PRIVACY MASK >>

SYSTEM HD-SDI RESOLUTION 1080p30

INFORMATION


30/65

OSD MENU

4

z

Focus Mode [AUTO/MANUAL/SEMIAUTO]


{

SEMIAUTO Mode

This mode automatically exchanges focus modes between Manual Focus mode and Auto Focus mode by operation. Manual Focus mode activates in preset operation and Auto Focus mode activates during jog operation z


Retains color balance over a color temperature range. In auto mode, this feature automatically processes the viewed image. In Manual mode, Red and Blue level can be set up manually. z z z

Red/Blue

Offset

Shutter

Iris

[0 ~ 255]

Adjusts the picture output in the red/blue range.

[ESC/A.Flicker/Manual(

×60~1/33000sec or ×60~1/30000sec)]

Sets Shutter Speed. Shutter Speed is the duration of the electronic shutter.

If Iris is set to Manual and Shutter Speed is set to ESC, Shutter Speed has higher priority. If Shutter Speed is set to A.Flicker, to remove Flicker,

Shutter Speed should be set to 1/100 sec. for NTSC and 1/120 for PAL

[AUTO/MANUAL(F1.6~F28/CLOSE or F1.35~F28/CLOSE)]

Sets Iris to operate automatically or at a user-defined level. If Iris is set to

Auto, Iris has higher priority in adjusting AE and Shutter Speed is fixed.

Auto iris is the lens function that automatically opens closes the iris in response to changing light conditions.

If Iris is set to Manual, Iris is fixed and Iris has lower priority in adjusting

AE, in comparison with others. z

Gain z z

Brightness

Backlight

[OFF/LOW/MIDDLE/HIGH/MANUAL(0~36dB or 0~42dB)]

Sets AGC. This setting enhances image brightness automatically in case that luminance level of image signal is too low.

[1~100]

Adjusts the brightness of the images. Iris, The Shutter Speed and Gain are adjusted automatically in correspondence with each numeric value.

[OFF/BLC/HLC]


HLC(High Light Compensation) function removes the high light in a limited environment such as parking garage. The level is adjuatable in the BLC mode and the level and masking color are adjustable in the HLC mode.


31/65

OSD MENU

4

z

Sens-Up

The WDR(Wide Dynamic Range) is a function for dividing an image into several blocks and correcting blocked-up shadows and blown-out hightlights in accordance with the intensity diffrence. It enables you to obtain images in which portions ranging from dark to light can be recognized, even when capturing a subject with a large intensity difference that is backlit or includes extremely light portions. The WDR function is supported on 30T model only.

[AUTO( ×2~×60)/OFF]

Sets SENS-UP. This setting activates Slow Shutter function when luminance of image (signal) is too dark.

It is possible to set up the maximum number of frames piled up one on another by Slow Shutter function z

SSNR [OFF/LOW/MIDDLE/HIGH]

Sets SSNR. This setting enhances the images by deducting noises when the gain level of the mages is too high. z

Sharpness [1-31]

Sets image sharpness to enhance pictures. z

Day/Night [AUTO/DAY/NIGHT]

Sets Day&Night mode. z

Digital Zoom [ON/OFF]


Image Flip [ON/OFF]


Stabilization [ON/OFF]

Compensates image vibrations by wind or others. The images with vibrations are compensated by Digital Zoom function and the image resolution with this function should be lower than normal image resolution when this function is turned on. Also this function may not work properly in the following cases.

Dark scene or Low contrast scene

High frequency vibration

During Pan/Tilt/Zoom/Focus moving

During Iris/Shutter/Gain moving


32/65

z

HD-SDI

Resolution

OSD MENU

4

NTSC

PAL

: [1080p30/1080i60/720p60/720p30]

: [1080p25/1080i50/720p60/720p30]




33/65

Video Setup (20W model)



ACTION - RED OFFSET 10

OSD - BLUE OFFSET 10

SYSTEM EXPOSURE MODE AUTO


- IRIS 13

- GAIN +19 dB

- BRIGHTNESS 19

BLC OFF

WDR OFF

DEFOG OFF

- LEVEL 5

AUTO DSS ON

APERTURE 8

DAY&NIGHT AUTO

DIGITAL ZOOM ON

IMAGE FLIP OFF

[NEXT : MORE]

OSD MENU

4

VIDEO PRIVACY MASK >>

PTZ HD-SDI RESOLUTION 1080p30

ACTION

OSD

SYSTEM

INFORMATION


34/65

OSD MENU

4

z

Focus Mode [AUTO/MANUAL/SEMIAUTO]


{

SEMIAUTO Mode

This mode automatically exchanges focus modes between Manual Focus mode and Auto Focus mode by operation. Manual Focus mode activates in preset operation and Auto Focus mode activates during jog operation.

With Manual mode at presets, Focus data is memorized in each preset in advance and the camera calls focus data in correspondence with presets as soon as camera arrives at presets. It should shorten time to get focuses .

Focus mode automatically changes to Auto Focus mode when jog operation starts. z


Retains color balance over a color temperature range. In auto mode, this feature automatically processes the viewed image. In Manual mode, Red and Blue level can be set up manually. z z

Red Offset

Blue Offset

[0 ~ 20]

Adjusts the picture output in the red range.

[0 ~ 20]

Adjusts the picture output in the blue range. z

Exposure Mode [AUTO/MANUAL/SHUTTER/IRIS/BRIGHTNESS]

Set Auto Exposure mode. z

Shutter [1/7(6) ~ 1/60000]

If AE mode is set to SHUTTER mode or MANUAL mode, this can be set up. z

Iris [CLOSE/1~13]

If AE mode is set to IRIS mode or MANUAL mode, this can be set up.

z

Gain z

Brightness

[0dB ~ 45dB]

If AE mode is set to MANUAL mode, this can be set up.

[0 ~ 31]

If AE mode is set to BRIGHTNESS mode, this can be set up. z

BLC [ON/OFF]



35/65

OSD MENU

4

z z z z z

WDR

Defog

Auto DSS

Aperture

Day/Night

[OFF/ON]

The WDR(Wide Dynamic Range) is a function for dividing an image into several blocks and correcting blocked-up shadows and blown-out hightlights in accordance with the intensity diffrence. It enables you to obtain images in which portions ranging from dark to light can be recognized, even when capturing a subject with a large intensity difference that is backlit or includes extremely light portions.

[ON/OFF]

Sets the Defog function. When se tot ON, WDR function does not work.

[ON/OFF]

When set to ON, ensure that the slow shutter is set to automatically when the brightness drops. Effective only when the AE mode is set to AUTO.

The Auto DSS function is not abailiable in WDR mode.

[0 ~ 10]

Adjust the enhancement of the edges of objects in the picture.

[AUTO/DAY/NIGHT]

Sets Day&Night mode. z

Digital Zoom [ON/OFF]


Image Flip [ON/OFF]


HD-SDI

Resolution

NTSC

PAL

: [1080p30/1080i60/720p60/720p30]

: [1080p25/1080i50/720p60/720p30]




36/65

Privacy Mask Setup

PRIVACY MASK

MASK NO 1 UNDEFINED

CLEAR MASK >

DISPLAY MASK OFF

EDIT MASK >>

MASK COLOR BLACK

OSD MENU

4

Privacy Zone Mask allows the user to program 8 rectangulars that can not be viewed by the operator of the system. To protect privacy, MAX. 8 Privacy Masks can be created on the arbitrary position to hide objects such as windows, shops or private house. With the Spherical

Coordinates system, powerful Privacy Zone Mask function is possible. A mask area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide. z

Mask NO [1~8]

Selects a Mask number to program. If the selected mask has already data, the camera moves as it was programmed. Otherwise, “UNDEFINED” will be displayed. z

Clear Mask Deletes the mask data of the selected mask number.

z

Display Mask [ON/OFF]

Sets if the mask of the selected mask number shows or not on the screen. z

Mask Color [BLACK/GRAY1~6/WHITE/RED/GREEN]

Sets the color of mask. The setting value is applied to all masks.

L

30S, 20S, 20W models only


37/65

Privacy Mask Area Setup

EDIT MASK

OSD MENU

4

MOVE TO TARGET POSITION

[NEAR : NEXT / FAR : CANCEL]

Move your camera to an area to mask, and press NEAR button. Then a mask will be displayed in the center of screen.

Privacy Mask Size Setup

EDIT MASK

[LEFT&RIGHT:WIDTH/UP&DOWN:HEIGHT]


Adjust the mask size. Use the joystick or the arrow buttons of your controller to adjust mask size. (Left/Right/Up/Down)


38/65

PTZ Setup

VIDEO

PTZ POWER UP ACTION ON

ACTION AUTO PARKING OFF

OSD - ACTION TYPE HOME

SYSTEM - ACTION NUMBER -

INFORMATION - WAIT TIME 00:10:00

AUTO FLIP ON

JOG MAX SPEED 120/SEC

JOG DIRECTION INVERSE

ZOOM PROPORTIONAL JOG ON

FREEZE IN PRESET OFF

OSD MENU

4

z

Power Up Action [ON/OFF]

Refer to “Other Functions" section. z

Auto Parking [ON/OFF]

If Auto Parking is set to ON, the camera runs an assigned function automatically if there is no PTZ command during the programmed "Wait

Time". z

Action Type /

Action Number

[HOME/PRESET/SWING/PATTERN/GROUP/PREV ACTION]

This feature defines the activity when the camera parks. If Park Action is set to “HOME”, the camera moves to the home position which is memorized when the system boots. If Park Action is set to “PREV. ACTION”, the camera runs the previous action which it ran most recently. z

Wait Time [1~59 sec. / 1~180 min.]

Wait Time can be programmed from 1 second to 180 minutes. z

Auto Flip [ON/OFF]

Refer to “Other Functions" section. z

Jog Max Speed [1 °/sec ~360°/sec]

Sets the maximum jog speed.


39/65

OSD MENU

4

z

Jog Direction [INVERSE/NORMAL]

Sets the Jog Direction. If this is set to ‘Inverse’, the view direction in the screen is same as the direction of joystick. If this is set to ‘Normal’, the view direction in the screen is the reverse dirction of joystick. z

Zoom

Propotional Jog z

Freeze in

Preset

[ON/OFF]

Decides whether jog operation speed is interlocked with zoom magnification. If this is set to “ON”, jog operation speed is interlocked with zoom magnification and jog operation speed becomes lower for easier control as zoom magnification becomes higher.

[ON/OFF]

Sets Frame Freeze Function. This feature freezes the scene on the monitor when going to a preset. At the start point of a preset movement, a camera starts freezing the image of the start point. Camera keeps displaying the image of the start point during preset movement and does not display the images which camera gets during preset movement. As soon as camera stops at preset end point, camera starts displaying live images which it gets at the end preset point. This feature also reduces bandwidth when working with digital systems or digital network systems.


40/65

ACTION Setup

VIDEO

PTZ

ACTION MOTION EDIT LOCK OFF

OSD PRESET >>

SYSTEM SWING >>

INFORMATION PATTERN >>

GROUP >>

ALARM TRIGGER >>

SCHEDULE >>

OSD MENU

4

z

Motion Edit

Lock

[ON/OFF]

If Motion Lock is set to ON, it is impossible to set up and delete Preset,

Swing, Pattern and Group. It is possible only to run those functions. To set up and delete those functions, enter into OSD menu.


41/65

PRESET Setup

OSD MENU

4

PRESET

PRESET NO 1 UNDEFINED

CLEAR PRESET >

EDIT SCENE >>

EDIT LABEL >> [ ]

RELAY OUT OFF

CAMERA LOCAL SETTING OFF

WHITE BALANCE AUTO

- RED OFFSET 128

- BLUE OFFSET 128

EXPOSURE MODE AUTO

- SHUTTER 1/60

- IRIS F6.8

- GAIN 2 dB

- BRIGHTNESS 10

BLC OFF

WDR OFF

AUTO DSS ON

APERTURE 12

DAY&NIGHT AUTO z

Preset No [1~255] MAX.

209 Presets except the Reserved Presets (Hot Keys)

Selects a preset number to set up. If a selected preset is already defined, the camera moves to the pre-defined position. If a selected preset is not defined, “UNDEFINED” shows on the monitor. z

Clear Preset Deletes the data of the selected Preset. z

Edit Scene Re-defines the scene position of the selected Preset.

z

Edit Label Edits the label of the selected Preset to show on the monitor when the preset runs. MAX. 10 alphanuberic characteristics are allowed.

Defines the relay output.

z

Relay Out z

Camera Local

Setting

[ON/OFF]

Image paremeters can be set up independently for each preset. There are 2 modes, "Global" mode & "Local" mode. The Global mode is that parameters are set up totally and simultaneously for all presets. The Global parameters setup can be done in "VIDEO" menu. The Local mode is that parameters are set up independently for each preset. Each Local parameter activate correspondingly when the camera arrives at each preset position. During jog operation, Global parameter should be applied.

All Local parameters do not change although Global parameters changes.

L

The sub-menu of Camera Local Setting depends on the model. Refer to

the description of “Video Setup”


42/65

Preset Scene Setup

EDIT PRESET

OSD MENU

4

①

Use the Joystick to move the camera to a desired position.

②

Save the preset position by pressing NEAR key.

③

Press FAR key to cancel targeting the preset position.



Preset Label Setup

EDIT LABEL

[ ]

----------

1234567890

ABCDEFGHIJ

KLMNOPQRST

UVWXYZabcd

efghijklmn

opqrstuvwx

yz<>-/:()

----------

Space



①

As soon as finishing selecting an alphabet or a number, the cursor moves to the next digit.

②

With Left/Right/Up/Down of the joystick, move to a desired character in the alphanumeric set. To select a desired character, press the

TELE key

. To clear current charcter and move to backward, press the WIDE key.

③

The end character in the alphanumeric set is space character.

43/65

SWING Setup

SWING

SWING NO 1 UNDEFINED

- 1ST PRESET

- 2ND PRESET

1 UNDEFINED

1 UNDEFINED

- SWING SPEED 30/sec

CLEAR SWING >

RUN SWING >

OSD MENU

4

z

Swing Number [1~10]

Selects a Swing number to edit. If the selected Swing is not defined,

"UNDEFINED" is displayed. z

1st Position

2nd Position

[PRESET 1~255]

Sets the 2 positions for a Swing function. If the selected preset is not defined, "UNDEFINED" is displayed.

When a swing function runs, the camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW(Clockwise) direction. Then the camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in CCW (Counterclockwise) direction. In case that the preset assigned as the 1st point and the preset assigned as the 2nd point are same, the camera turns on its axis by 360 ° in

CW direction and then it turns on its axis by 360 ° in CCW direction. z

Swing Speed [1 °/sec. ~180°/sec.]

Defines Swing speed between the 2 Preset positions from 1 °/sec to

180 °/sec z

Clear Swing Deletes the data of the selected Swing. z

Run Swing Runs Swing for the test purposes to check if it works properly.


44/65

PATTERN Setup

PATTERN

PATTERN NO 1 UNDEFINED

CLEAR PATTERN >

RUN PATTERN >

EDIT PATTERN >>

OSD MENU

4

z

Pattern No [1~4]

Selects a Pattern number to edit. If the selected pattern number is not defined, "UNDEFINED" will be displayed. z

Clear Pattern Deletes the data of the selected pattern. z

Run Pattern Runs the Pattern for the test purposes to check if it works properly.

z

Edit Pattern Edits the selected pattern.


45/65

OSD MENU

4

Edit Pattern

EDIT PATTERN



EDIT PATTERN ] 90%

PATTERN RECORDING


①

With the Joystick of your controller, move the camera to the start position with an appropriate zoom magnafication. To start the pattern recording, press

NEAR key. To exit, press FAR key.

②

Move camera with joystick of controller to memorize the path (mostly curve path) in the selected pattern. The movement by Joystick will be memorized in a pattern. After a pattern is programmed, the remaining storage is displayed in progress bar on the screen.

③

To save the data and exit, press NEAR key. To cancel saving the data and delete the data, press FAR key.


46/65

GROUP Setup

OSD MENU

4

GROUP

GROUP NO 1 UNDEFINED

CLEAR GROUP >

RUN GROUP >

------------------------------------------

NO ACTION TYPE ACTION NO DWELL OPTION

------------------------------------------

1 UNDEFINED 1 00:05 -










[FAR : MOVE TO TOP] z

Group No [1~8]

Selects a Group number to edit.

If the selected Group number is not defined, "UNDEFINED" will be displayed. z

Clear Group Deletes the data of the selected Group. z

Run Group Runs the Group for the test purposes to check if it works properly.

z z

Action Type

Action No

Dwell

[UNDEFINED/PRESET/SWING/PATTERN]

Selects the actions to execute. MAX. 40 actions are allowed in a Group.

[0 SEC. ~ 4 MIN.]

Sets the Dwell Time between functions. z

Option Option. It is a preset speed when a preset is selected in the Action. It is the number of repeat when a Pattern or a Swing is selected in the Action.

Press the FAR key to move the cursor position to “Group No” after edit of actions is complete.


47/65

ALARM TRIGGER Setup

ALARM TRIGGER

ALARM NO 1

ALARM TYPE NORMAL OPEN

TRIGGERED ACTION UNDEFINED

TRIGGERED ACTION NO -

TRIGGERED HOLD TIME ENDLESS

POST ACTION HOME

POST ACTION NO -

OSD MENU

4

z

Post Action /

Post Action No z z

Alarm No

Type z

Triggered Action

/ Action No z

Hold Time

[1~3]

Selects a sensor number to set up.

[NORMAL OPEN/ NORMAL CLOSE]

Selects sensor operation type.

[UNDEFINED/PRESET/PATTERN/SWING/GROUP]

Selects an action to run when a sensor signal is input.

[ENDLESS / 1~59 SEC. / 1~180 MIN.]

Sets the time period for the action which is run by external sensor activation. After the time period passes, the action pre-defined in “Post

Action” runs sequentially in succession to the action by external sensor activation. If this option is set to “ENDLESS”, “Post Action” does not activate.

[HOME/PRESET/PATTERN/SWING/GROUP/PREV ACTION]

Selects the action that a camera will run after the time period in“HOLD

TIME” passes. If Post Action is set to “PREV. ACTION”, the camera runs the previous action which it ran most recently.


48/65

SCHEDULE Setup

SCHEDULE

SCHEDULE NO 1

SCHEDULED ACTION UNDEFINED

SCHEDULED ACTION NO -

SCHEDULED HOLD TIME ENDLESS

POST ACTION HOME

POST ACTION NO -

ACTION CYCLE ONCE

- YEAR 2012

- MONTH JAN

- DAY 1

- HOUR 0

- MINUTE 0

- SECOND 0

OSD MENU

4

z

Schedule No [1~8]

Selects a Schedule to be configured. z

Action /

Action No z

Hold Time

[UNDEFINED/PRESET/PATTERN/SWING/GROUP]

Consigures a function to be run for a configured time period.

[ENDLESS / 1~59 SEC. / 1~180 MIN.]

Configures a time period to run an Action. After this time passes, “Post

Action” should run. If Post Action is configured to ENDLESS, Post Action should not run. z

Post Action /

Post Action No z z

Cycle

Time

[HOME/PRESET/PATTERN/SWING/GROUP/PREV ACTION]

Configures a function to be run after a Hold Time. When “PREV. ACTION" is configured, the latest function which is running just before a Schedule

Function should keep running again.

[ONCE/HOURLY/DAILY/WEEKLY/MONTHLY]

Configures a time period to repetitively run a Schedule Function. If “ONCE” is configured, a Schedule function should run once and it should not run again.

Configures a Date and a Timeto run a Schedule Function.


49/65

OSD Setup

VIDEO

PTZ

ACTION

OSD DISP CAMERA ID ON

SYSTEM DISP ALARM I/O AUTO

INFORMATION DISP PTZ INFO AUTO

DISP ACTION TITLE AUTO

DISP PRESET LABEL AUTO

DISP TIME ON

DISP DATE ON

OSD MENU

4

OSD setup allows you to program how labels are displayed on the monitor. In case of AUTO, the labels are displayed on the monitor when there are any changes in parameters.

z

Camera ID [ON/OFF]

Displays the selected Camera ID. z

Alarm I/O [ON/OFF/AUTO]

Displays the activated alarms. This information shows the current state of

Alarm Inputs and Relay Outputs. If an Input point is ON state, it will show a number corresponding to each point. If an Input point is OFF state, '-' will be displayed. z

PTZ Information [ON/OFF/AUTO]

Displays the positions of pan/tilt, zoom magnification. z

Action Title [ON/OFF/AUTO]

Identfies Actions.

"PRESET xxx", "PATTERN x", "SWG x-PRESET xxx", "UNDEFINED" z

Preset Label [ON/OFF/AUTO]

Displays the preset labels when the camera arrives at presets.


50/65

OSD MENU z Display Date

[ON/OFF]

Configures whether Date will be displayed in OSD or not

. z

Display Time

[ON/OFF]

Configures whether Time will be displayed in OSD or not

.

4


51/65

SYSTEM Setup

VIDEO

PTZ

ACTION

OSD

SYSTEM LANGUAGE ENGLISH

INFORMATION TIME SETTING >>

HEATER SETTING AUTO

ENABLE PASSWORD OFF

EDIT PASSWORD >>

FACTORY RESET >

- RESET VIDEO >

- RESET PTZ >

- RESET ACTION >

- RESET OSD >

REBOOT SYSTEM >

OSD MENU

4

z

Heater Setting [AUTO/ON/OFF]

Configures how Heater works. If this is set to “AUTO”, an internal sensor detects internal temperature and Heater automatically starts working or stops working according to internal temperature change. z

Enable Password [ON/OFF]

Configures whether OSD menu will be protected with a password.

z

Factory Reset Deletes all configuration data and the system is set to the factory default.

If the Factory Reset is selected, a message asks for the final confirmation.

Press the NEAR button for the final confirmation.

Initializes all the configuration data for VIDEO menu.

z

Reset Video z z

Reset PTZ

Reset Action

Initializes all the configuration data for PTZ menu.

Initializes all the configuration data for ACTION menu.

z

Reset OSD Initializes all the configuration data for OSD menu.

z

Reboot System Reboots the system.


52/65

Factory Default z

Video Menu Setting (30S, 20S Model)

Focus Mode

White Balance

Exposure Mode

SEMIAUTO

AUTO

AUTO

Day&Night

Digital Zoom

Image Flip

OSD MENU

AUTO

ON

OFF

4

Auto DSS ON HD-SDI Resolution

Aperture 12 z

Video Menu Setting (30T, 20T, 19T Model)

Focus Mode

White Balance

SEMIAUTO

AUTO

Sharpness

Day&Night

1080p30 (NTSC)

12

AUTO

Iris AUTO OFF

Brightness 50 Privacy UNDEFINED

Sens-Up Auto

SSNR MEDIUM z

Video Menu Setting (20W Model)

Focus Mode

White Balance

Exposure Mode

SEMIAUTO

AUTO

AUTO

Aperture

Day&Night

Digital Zoom

8

AUTO

ON

ON

HD-SDI (NTSC)

1080p25 (PAL) Auto DSS


53/65

OSD MENU

4

z

PTZ Menu Setting

Power Up Action

Auto Parking

Auto Flip

Jog Max Speed

Jog Direction

ON

OFF

Zoom Proportional Jog ON

Freeze In Preset OFF z

ACTION Menu Setting

Motion Edit Lock

Preset

ON Swing

120 °/sec Pattern

INVERSE Group

Alarm Trigger

Schedule z

OSD Menu Setting

Disp Camera ID

Disp Alarm I/O

Disp PTZ Info

Disp Action Title

Disp Preset Label

Disp Time

Disp Date

ON

AUTO

AUTO

AUTO

AUTO

ON

ON z

SYSTEM Menu Setting

Time

Heater Setting

Enable Password

Password

OFF

UNDEFINED

UNDEFINED

UNDEFINED

UNDEFINED

UNDEFINED

UNDEFINED

01/JAN/2012

00:00:00

AUTO

OFF

Blank


54/65

TIME Setup

TIME SETTING

YEAR 2012

MONTH JAN

DAY 1

HOUR 0

MINUTE 0

SECOND 0

OSD MENU

4

Configure current date and time

. HOUR does not support AM or PM form. HOUR can be configured in 24 hour form.


55/65

PASSWORD Setup

OSD MENU

4

CHANGE PASSWORD

[ ]

----------

1234567890

ABCDEFGHIJ

KLMNOPQRST

UVWXYZabcd

efghijklmn

opqrstuvwx

yz<>-/:()

----------

Space


①

As soon as finishing selecting an alphabet or a number, the cursor moves to the next digit.

②

With Left/Right/Up/Down of the joystick, move to a desired character in the alphanumeric set. To select a desired character, press the TELE key

. To clear current charcter and move to backward, press the WIDE key.

③

The end character in the alphanumeric set is space character.

[Caution] It is mandatorily recommended that a user must take a memo for a password before a user applies a password to a system. When a Password is forgotten, a unit can not be unlocked and the unit is supposed to be shipped back to the manufacturer.


56/65

Specifications

SPECIFICATIONS

Image Sensor

Zoom

Forcal Length

Angle of View (H)

Min. Working Distance

CAMERA PART (30S Model)

1/2.8'' Exmor CMOS Sensor

×30 Optical Zoom, ×12 Digital Zoom

F1.6~4.7, f=4.61~138.3mm

57.5

°(Wide)~2.1°(Tele)

10mm(Wide), 1200mm(Tele)

Minimum Illuminance

Day & Night

Focus

AE Mode

White Balance

0.5 Lux (Color, 1/30sec, 50 IRE)

0. 005 Lux (B/W, 1/4 or 1/3sec, 50 IRE)

Auto / Day / Night(ICR)

Auto / Manual / SemiAuto

Auto / Iris / Shutter / Manual / Brightness

Auto / Manual(Red, Blue Gain Adjustable)

BLC

WDR

On / Off

On / Off

Aperture Adjustable

NR Yes

Privacy Zone

Stabilization

8 Masks, Spherical Coordinate

ON / OFF

5


57/65

Image Sensor

Zoom

SPECIFICATIONS

5

CAMERA PART (20S Model)

1/2.8'' Exmor CMOS Sensor


Angle of View (H) 55.4


Min. Working Distance 10mm(Wide), 1000mm(Tele)

Minimum Illuminance

Day & Night

Focus

AE Mode

White Balance

0.5 Lux (Color, 1/30sec, 50 IRE)

0. 005 Lux (B/W, 1/4 or 1/3sec, 50 IRE)





BLC

WDR

On / Off

On / Off

Aperture Adjustable

NR

Privacy Zone

Yes

8 Masks, Spherical Coordinate


58/65

SPECIFICATIONS

5

Image Sensor

Zoom

CAMERA PART (30T Model)

1/4'' PS CMOS Sensor


Forcal Length

Angle of View (H)

Min. Working Distance

F1.35~3.7, f=3.5~101.5mm

H : 54.8

°(Wide)~2.01°(Tele) / V : 44.6°(Wide)~1.61°(Tele)

1500mm

Minimum Illuminance

Day & Night

Focus

White Balance

Iris

1.5 Lux (Color, F1.6, 50 IRE) / 0. 1Lux (B/W, F1.6,50 IRE)




Auto / Manual

Gain

Shutter Speed

BLC

OFF / Low / Middle / High / Manual

Auto / Manual( ×60~1/33,000) / A.FLK

OFF / BLC / HLC

SSNR Low / Middle / High / OFF

Sens-Up OFF / Auto ( ×2~×60)

Brightness 1~100

Sharpness 1~31

Privacy Zone 8 Masks, Spherical Coordinate

Stabilization ON / OFF


59/65

Image Sensor

Zoom

SPECIFICATIONS

5




Min. Working Distance 1000mm

Minimum Illuminance

Day & Night

Focus

White Balance

Iris

1.5 Lux (Color, F1.6, 50 IRE) / 0. 1Lux (B/W, F1.6,50 IRE)




Auto / Manual

Gain

Shutter Speed

BLC


Auto / Manual( ×60~1/33,000) / A.FLK

OFF / BLC / HLC



Brightness 1~100

Sharpness 1~31




60/65

Image Sensor

Zoom

SPECIFICATIONS

5




Min. Working Distance 1000mm

Minimum Illuminance

Day & Night

Focus

White Balance

Iris

0.7 Lux (Color, F1.6, 50 IRE) / 0. 08 Lux (B/W, F1.6,50 IRE)




Auto / Manual

Gain

Shutter Speed

BLC


Auto / Manual( ×60~1/30,000) / A.FLK

OFF / BLC / HLC



Brightness 1~100

Sharpness 1~31




61/65

SPECIFICATIONS

Image Sensor

CAMERA PART (20W Model)

1/3'' Panasonic CMOS Sensor

Zoom ×20 Optical Zoom, ×12 Digital Zoom

Forcal Length

F1.6~3.5, f=4.7~94.0mm

Angle of View (H) 55.4


Minimum Illuminance

0.5 Lux (Color)

0. 001 Lux (B/W, DSS)

Day & Night

Focus



AE Mode

White Balance

BLC

WDR



On / Off

On / Off

Defog On / Off

Aperture Adjustable

NR Yes


5


62/65

SPECIFICATIONS

Movement

Range

Speed

MECHANISM PART

Pan 360 °(Endless)

Tilt 90 °

Preset 500 °/sec.

5

Group

8 Groups (MAX. 40 Actions with The Combination of Preset,

Pattern and Swing)

Other Pan/Tilt Functions Auto Flip, Auto Parking, Power Up Action and etc.

Video Ouptut 2 ×BNC (HD-SDI and CVBS)

HD-SDI

HDcctv v1.0, 1.485Gb/s, SMPTE 292M standard

Resolution : 1080p/30/25, 1080i/60/50, 720p/60/50/30/25

CVBS 1Vp-p

Real Time Clock Yes, RTC battery backup time : 2 weeks

Communication RS-485

OSD

English

Menu / Time / PTZ information etc, Password protection

Sensor Input 3 Inputs, Photo-Coupler Type, DC 5V~12V

Fan Always ON

Heater Operation Start from Internal Temperature 10 °C

Operation Temperature -30 °C ~ 50°C

Rated Power DC 12V / 1.8A or AC 24V / 2.0A


63/65

SPECIFICATIONS

5

MECHANICAL

Ceiling Mount

Material

Dome Size

Dimension

Weight

Wall Mount

Dome Polycarbonate

Internal Polycarbonate, ABS

External Aluminium

∅150mm / ∅ 5.9”

∅200×407.8mm

Approx 3.6Kg

300 ×309.1mm

Approx 3.4Kg

[Note]

1) Specification and features are subject to change without prior notice.

2) Specification and features are different by models.

3) Check the voltage and current capacity of rated power carefully.


64/65

Dimension

z

Main Body

200

15

0

SPECIFICATIONS

5

z

Ceiling Mount Type

56.4 56.4

158.2

1.5" NPT z

Wall Mount Type

300

118.6

80

4- 8


[Unit : mm]

65/65

INSTRUCTION MANUAL Ver 1.2

INSTRUCTION MANUAL

Megapixel PTZ Camera

CAUTION

Important Safety Guide

Caution

Model Code

Option

S : HD-SDI output

Mount Bracket

W : Wall Mount

C : Ceiling Mount

Zoom

30S : Optical x30, 2M pixels

20S : Optical x20, 2M pixels

30T : Optical x30, 1.3M pixels

20T : Optical x20, 2M pixels

19T : Optical x19, 1.3M pixels

20W : Optical x20, 2M pixels

Composite Video Signal

N : NTSC

P : PAL

Series

HC: Megapixel PTZ (HD-SDI)

Features

Package Component

Main Part Description

DIP Switch Setup

Installation with Ceiling Mount Bracket

Installation with Wall Mount Bracket

Wiring and Cabling

Check Points before Operation

Check Points for Preset and Pattern Function before Operation

OSD Menu

Reserved Presets (Hot Keys)

Preset

Swing

Pattern

Group

Other Functions

OSD Display

Quick Programming Guide

Video Setup (30S, 20S model)

Video Setup (30T, 20T, 19T model)

Video Setup (20W model)

Privacy Mask Setup

PTZ Setup

ACTION Setup

PRESET Setup

SWING Setup

PATTERN Setup

GROUP Setup

ALARM TRIGGER Setup

SCHEDULE Setup

OSD Setup

SYSTEM Setup

TIME Setup

PASSWORD Setup

Specifications

Dimension

Related manuals

Avico

APO-SDI20M-NX20W

Eyemax

PT TP 950 Series

CBC

PT118XT-HD

Tamron

1A1HA

Balter

BTZ-2700

Adirondack Technology

MBO-N10TW-DIN

Digimerge

DPZ16WO37

Genie CCTV

ASD276

Table of contents