ESAB TXH™ Tig- Torches Instruction manual

GB

RU

TXHt Tig- torches

TXHt 120, TXHt 150, TXHt 200,

TXHt 250w, TXHt 400w

Instruction manual

0460 031 127

0460 031

2007--05--30

Èíñòðóêöèÿ ïî ýêñïëóàòàöèè

Ðóññêèé . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ENGLISH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3

9

Rights reserved to alter specifications without notice.

Îñòàâëÿåì çà ñîáîé ïðàâî èçìåíÿòü ñïåöèôèêàöèþ áåç ïðåäóïðåæäåíèÿ.

-- 2 --

ENGLISH

1 DIRECTIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 INTRODUCTION

3.1 Equipment

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2 Choice of electrode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3 Grinding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 MAINTENANCE

6.1 Daily

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 FAULT--TRACING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 ORDERING SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ORDERING NUMBER

WEAR PARTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13

13

14

14

11

12

12

12

13

18

20

22

10

10

11

11

TOCe

-- 9 --

GB

1 DIRECTIVE

DECLARATION OF CONFORMITY

ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that the welding torch/welding gun

TXH 120 -- 400w are constructed and tested in compliance with the standard EN 60974--7 in accordance with the requirements of directive (2006/95/EC).

--------------------------------------------------------------------------------------------------------------------------------------

Laxå 2007--05--28

Kent Eimbrodt

Global Director

Equipment and Automation

2 SAFETY

Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of welding equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the welding equipment. Incorrect operation of the equipment may lead to hazardous situations which can result in injury to the operator and damage to the equipment.

1.

Anyone who uses the welding equipment must be familiar with:

S its operation

S location of emergency stops

S its function

S relevant safety precautions

S welding

2.

3.

The operator must ensure that:

S no unauthorized person is stationed within the working area of the equipment when it is started up.

S no--one is unprotected when the arc is struck

The workplace must:

S be suitable for the purpose

S be free from drafts

4.

5.

Personal safety equipment

S

Always wear recommended personal safety equipment, such as safety glasses, flame--proof clothing, safety gloves.

S

Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become trapped or cause burns.

General precautions

S

Make sure the return cable is connected securely.

S

Work on high voltage equipment may only be carried out by a qualified electrician.

S

Appropriate fire extinquishing equipment must be clearly marked and close at hand.

WARNING!

Read and understand the instruction manual before installing or operating.

Voltage max. 15 kV.

-- 10 --

bg19e1

GB

WARNING

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU-

TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE

BASED ON MANUFACTURERS’ HAZARD DATA.

ELECTRIC SHOCK -- Can kill

S

Install and earth the welding unit in accordance with applicable standards.

S

S

S

Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

Insulate yourself from earth and the workpiece.

Ensure your working stance is safe.

FUMES AND GASES -- Can be dangerous to health

S

Keep your head out of the fumes.

S

Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone and the general area.

ARC RAYS -- Can injure eyes and burn skin.

S

Protect your eyes and body. Use the correct welding screen and filter lens and wear protective

S clothing.

Protect bystanders with suitable screens or curtains.

FIRE HAZARD

S

Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE -- Excessive noise can damage hearing

S

Protect your ears. Use earmuffs or other hearing protection.

S

Warn bystanders of the risk.

MALFUNCTION -- Call for expert assistance in the event of malfunction.

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

PROTECT YOURSELF AND OTHERS!

ESAB can provide you with all necessary welding protection and accessories.

3 INTRODUCTION

TIG torch TXH 120 --TXH 400w is intended for manual TIG welding and is available water or air cooled. Certain models are available with flex heads for unlimited movement in confined spaces.

ESAB’s accessories for the product can be found on page 22.

3.1

Equipment

TIG torch TXH 120--TXH 400w is supplied with an electrode Ø 2,4 mm, wear parts and an instruction manual.

4 TECHNICAL DATA

NOTE! Technical data valid for the tig--torch is presented on page 15.

Duty cycle

The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a certain load without overloading.

Protection class

The torches protection class machine side (EN 60 529)

IP3X

The IP--code indikates the enclosure class, i.e. the dregree of protection against penetration by solid objects of 2,5 mm Ø and greater.

-- 11 --

bg19e1

GB

5 OPERATION

General safety regulations for the handling of the equipment can be found on page 10 . Read through before you start using the equipment!

Please also read the operating instructions for the welding components, e.g. power source and connect accordingly.

5.1

Connections

Tighten the connections for the torch carefully to avoid overheating the connection, connection interference, mechanical damage or leakage of liquid or gas.

Connect water connections to the torch so that the red terminal is always connected to the corresponding red terminal and the blue terminals are always connected to the corresponding blue terminals.

5.2

Choice of electrode

By alloying the tungsten electrode with 1% to 2% lantha or cerium the electron discharge is increased, which gives better striking and restriking and therefore increased arc stability. Alloyed tungsten electrodes have a longer service life, tolerate higher currents and are less likely to leave tungsten residue in the weld.

Pure tungsten electrode (AC) -- Green,

WP

Ceriumlegerad volframelektrod

(AC/DC) -- Grey, WC20

used when welding light metal alloys

Lantha alloyed tungsten electrod (DC)

-- Gold, WL15

Lantha alloyed tungsten electrod

(AC/DC) -- Black, WL10

used when welding light metals such as aluminium and magnesium. Electrode tip must be rounded when welding usually used when welding stainless steel, steel, copper, titanium etc.

used when welding light metal alloys, stainless steel, steel, copper, titanium etc.

Selection table

1.0

1.6

2.4

3.2

4.0

A / AC A / DC

W CeO

2

La

2

O

3

CeO

2

La

2

O

3

6.4/ 8.0

6.4/8.0/9.8

10--60 -15--100 70--80 20--100

50--100 60--90 70--160 80--140 80--160

9.8/11.2 /2.7

100--160 90--130 110--200 150--210 120--230

11.2/12.7

12.7

130--180 140--190 150--205 220--320 200--305

180--230 200--250 180--270 330--420 250--420

-- 12 --

bg19e1

GB

5.3

Grinding

Grind tungsten electrodes according to the following table:

NOTE that tungsten electrodes must be ground lengthways. If they are ground incorrectly the arc may be unstable. When the welding current is increased the angle must also be increased.

When welding with alternating current (AC) the electrode end must be gently rounded. Grinding the electrode is then unnecessary. Light grading of the edge is sufficient. The electrode forms itself if it is carefully overloaded. If the tip becomes ball shaped while welding using alternating current, this is a sign that the current is too high for the diameter of electrode being used.

Welding current

20 A

20 --100 A

100 --200 A over 200 A

Electrode angle

30°

30°--90°

90°--120°

120°

6 MAINTENANCE

Regular maintenance is important for safe, reliable operation.

IMPORTANT! Switch off the ignition of the power source when cleaning the torch.

Note!

All guarantee undertakings from the supplier cease to apply if the customer himself attempts any work in the product during the guarantee period in order to rectify any faults.

6.1

Daily

S

Check that all cables and hoses are undamaged and that there are no kinks in them.

S

Check that the gas nozzle is free from defects and suitable for the work in question.

S

Check that the shielding gas flows evenly and without restriction.

S

Check that the electrode is undamaged and that the electrode has been ground to the correct angle.

S

Check the water flow at the unit’s return line.

-- 13 --

bg19e1

GB

7 FAULT--TRACING

Please also read the operating instructions for the welding components, e.g. power source.

If the measures described below are not successful, please consult your dealer or the manufacturer.

Problem Cause

The arc does not strike S Cable or contact is poor.

S

Torch electrode is badly oxidised.

S

There are impurities in the shielding gas (moisture, air).

S

The electrode used is too large or stubby at low current

No trigger function

Gas shielding is poor

Solution

S

Check the cable and contact.

S

Regrind along the length of the electrode.

S

Flush clean with gas.

S

Replace with a smaller electrode

S

Control cable interrupted/faulty.

S

Check/repair.

S

S

There are impurities in the base material (rust, lubricant).

S

Insufficient or total lack of shielding gas.

S

It is too draughty at the welding site.

S

There are impurities in the shielding gas (moisture, air).

Welding spray has fastened on the gas lens or the gas hood.

S

Flush clean with gas.

S

S

Clean the base material.

Check contents of the gas bottle/hoses and the pressure setting.

S

Shield the welding area with protective screens.

S

Clean or replace.

8 ORDERING SPARE PARTS

Spare parts may be ordered through your nearest ESAB dealer, see the last page of this publication.

ESAB’s spare parts for the product , will be found on the internet www.esab.com.

TXHt 120--400w are designed and tested in accordance with the international and Eu-

ropean standards IEC/EN 60974--7 and EN 60974--7. It is the obligation of the service unit which has carried out the service or repair work to make sure that the product still conforms to the said standard.

bg19e1

-- 14 --

Technical data

Operating temperature range

Transportation temperature

TXH

120

120r

--

120/60

100/100

TXH

120V

--

--10 to +40

˚C

--25 to +55 ˚C

120/60

100/100

TXH

120F

120Fr

--

120/60

100/100

TXH

150

150r

150/35

120/60

100/100

TXH

150V

150/35

120/60

100/100

TXH

150F

150Fr

150/35

120/60

100/100

1.0--3.2

1.0--3.2

1.0--3.2

1.0--3.2

1.0--3.2

1.0--3.2

Ar

Ar/He

Ar

Ar/He

Ar

Ar/He

Ar

Ar/He

Ar

Ar/He

Ar

Ar/He

4 & 8 m 4 & 8 m 4 & 8 m 4 & 8 m 4 & 8 m 4 & 8 m

X -X X -X

15 15 15 15 15 15 max. kV

113 113 113 113 113 113

Up max. V

bg19t11a1

-- 15 --

Edition 2007--05--30

max. kV

TXH

200

200r

--

TXH

200V

--

TXH

200F

200Fr

--

TXH

250w

250wr

X

TXH

250wF

250wFr

X

TXH

400w

400wr

X

---70 70 70

200/35

150/60

140/100

200/35

150/60

140/100

200/35

150/60

140/100

--

250/60

200/100

--

250/60

200/100

400/35

350/60

300/100

1.0--4.0

1.0--4.0

1.0--4.0

1.0--3.2

1.0--3.2

1.0--4.8

Ar

Ar/He

Ar

Ar/He

Ar

Ar/He

Ar

Ar/He

Ar

Ar/He

Ar

Ar/He

4 & 8 m 4 & 8 m 4 & 8 m 4 & 8 m 4 & 8 m 4 & 8 m

X -X X X X

15 15 15 15 15 15

113 113 113 113 113 113

Up max. V

---0.5

0.5

0.5

MPa

MPa

---0.1

0.1

0.1

q l/min

---1 1 1 bg19t11a1

-- 16 --

Edition 2007--05--30

Flow caracteristic Îõëàæäàþùàÿ ïðèíàäëåæíîñòè

Flow characterstic TXH250w, TXH250wF and TXH 400w at 50 Hz

Q

(l/min)

2,5

2

1,5

1

0,5

0

0

P = Pressure Pump pressure

Q = Flow rate Flow rate

0,5

P

1

(bar)

1,5

TXH 250w

TXH 250wF

TXH 250w

TXH 400w

2

bg19ft

-- 17 --

TXH 120 - 400wr

Ordering number Íîìåð çàêàçà

Ordering no.

Type

Torch head

OKC 25

V= valve, F= flexible head

OKC 50

Connection

ESAB Tig

Connection

Origo

Switch Valve Flexible head

4 m 8 m 4 m 8 m 4 m 8 m 4 m 8 m

0460 010 840 TXHt 120

0460 010 841 TXHt 120V

0460 010 842 TXHt 120

0460 010 843 TXHt 120F

0460 010 844 TXHt 120F

0460 010 880 TXHt 120

0460 010 881 TXHt 120V

0460 010 882 TXHt 120

0460 010 883 TXHt 120F

0460 010 884 TXHt 120F

0460 010 940 TXHt 120

0460 010 941 TXHt 120F

0460 010 980 TXHt 120

0460 010 981 TXHt 120F

0460 011 840 TXHt 150

0460 011 841 TXHt 150V

0460 011 842 TXHt 150

0460 011 843 TXHt 150V

0460 011 844 TXHt 150F

0460 011 845 TXHt 150F

0460 011 880 TXHt 150

0460 011 881 TXHt 150V

0460 011 882 TXHt 150

0460 011 883 TXHt 150V

0460 011 884 TXHt 150F

0460 011 885 TXHt 150F

0460 011 940 TXHt 150

0460 011 941 TXHt 150F

0460 011 980 TXHt 150

0460 011 981 TXHt 150F

0460 012 840 TXHt 200

0460 012 841 TXHt 200V

0460 012 842 TXHt 200F

0460 012 880 TXHt 200

0460 012 881 TXHt 200V

0460 012 882 TXHt 200F

0460 013 840 TXHt 250w

0460 013 841 TXHt 250wF

0460 013 880 TXHt 250w

0460 013 881 TXHt 250wF

0460 014 840 TXHt 400w

0460 014 881 TXHt 400w

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

Spare parts are to be ordered through the nearest ESAB agency as per the list on the back of the cover. Kindly indicate type of unit, serial number, denominations and ordering numbers according to the spare parts list.

Maintenance and repair work should be performed by an experienced person, and electrical work only by a trained electrician.

Use only recommended spare parts.

Water

X

X

X

X

X

X bg19or

-- 18 --

Edition 2007--05--30

TXH 120 - 400wr

Ordering no.

Type

0462 010 842 TXHt 120r

0462 010 844 TXHt 120Fr

0462 010 882 TXHt 120

0462 010 884 TXHt 120Fr

0462 011 842 TXHt 150r

0462 011 845 TXHt 150Fr

0462 011 882 TXHt 150r

0462 011 885 TXHt 150Fr

0462 012 840 TXHt 200r

0462 012 842 TXHt 200Fr

0462 012 880 TXHt 200r

0462 012 882 TXHt 200Fr

0462 013 840 TXHt 250wr

0462 013 841 TXHt 250wF

0462 013 880 TXHt 250wr

0462 013 881 TXHt 250wFr

Switch

X

X

X

X

X

X

Torch body

Valve

F= flexible body, w=water cooled, r= remote

OKC 25 OKC 50

Connection

ESAB Tig

Connection

Origo

Water

4 m 8 m Flexible body

4 m 8 m 4 m 8 m 4 m

X

X

X

X

X

X

X

X

8 m

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

0462 014 840 TXHt 400wr

0462 014 880 TXHt 400wr

0462 014 841 TXHt 400wr HD

0462 014 881 TXHt 400wr HD

X

X

X

X

X

X

X

X

X

X

X X

NB. CAN based adapter, is to be used for connection of above TIG torches with remote function, see Accessories on page 22.

Spare parts are to be ordered through the nearest ESAB agency as per the list on the back of the cover. Kindly indicate type of unit, serial number, denominations and ordering numbers according to the spare parts list.

Maintenance and repair work should be performed by an experienced person, and electrical work only by a trained electrician.

Use only recommended spare parts.

X

X

X

X

X

X

X

X bg19or

-- 19 --

Edition 2007--05--30

TXH 120 - 400wr

Wear parts Áûñòðîèýíàøèâåìûå äåòàëè

Ordering no.

175 mm

Ordering no.

150 mm

Tungsten electrodes

Eco

0151 574 008 0151 574 208 Wolfram, pure

0151 574 009 0151 574 209 Wolfram, pure

-0151 574 245 Wolfram, pure

0151 574 010 0151 574 210 Wolfram, pure

0151 574 011 0151 574 211 Wolfram, pure

0151 574 012 0151 574 212 Wolfram, pure

0151 574 001 0151 574 201 Lantan 1.5%

0151 574 002 0151 574 202 Lantan 1.5%

-0151 574 244 Lantan 1.5%

0151 574 003 0151 574 203 Lantan 1.5%

0151 574 004 0151 574 204 Lantan 1.5%

0151 574 005 0151 574 205 Lantan 1.5%

0151 574 030

0151 574 031

0151 574 032

0151 574 033

0151 574 034

--

--

--

--

--

Lantan 1%

Lantan 1%

Lantan 1%

Lantan 1%

Lantan 1%

0151 574 036 0151 574 236 Cerium 2%

0151 574 037 0151 574 237 Cerium 2%

-0151 574 242 Cerium 2%

0151 574 038 0151 574 238 Cerium 2%

0151 574 039 0151 574 239 Cerium 2%

0151 574 040 0151 574 240 Cerium 2%

Diameter Colour

ø 1.0

ø 1.6

ø 2.0

ø 2.4

ø 3.2

ø 4.0

ø 1.0

ø 1.6

ø 2.0

ø 2.4

ø 3.2

ø 4.0

ø 1.0

ø 1.6

ø 2.4

ø 3.2

ø 4.0

ø 1.0

ø 1.6

ø 2.0

ø 2.4

ø 3.2

ø 4.0

Gold

Gold

Gold

Gold

Gold

Gold

Green

Green

Green

Green

Green

Green

Black

Black

Black

Black

Black

Grey

Grey

Grey

Grey

Grey

Grey

Code

WL15

WL15

WL15

WL15

WL15

WL15

WP

WP

WP

WP

WP

WP

WL10

WL10

WL10

WL10

WL10

WC20

WC20

WC20

WC20

WC20

WC20

Current

DC

DC

DC

DC

DC

DC

AC

AC

AC

AC

AC

AC

DC

DC

DC

DC

DC

AC/DC

AC/DC

AC/DC

AC/DC

AC/DC

AC/DC bg19wear

-- 20 --

Edition 2007--05--30

TXH 120 - 400wr

Nozzles, collets, collet bodies and gas lenses for TXHt

torches

Type Size Denomination TXH 140/250W TXH 150/200 TXH 400W

No 4

No 5

No 6

Ø 6.4

Gas nozzles standard

Ø 8.0

Ø 9.8

No 7

No 8

Ø 11.2

Ø 12.7

No 10 Ø 15.9

No 12 Ø 19.0

0365 310 044 0157 123 052 0157 123 057

0365 310 045 0157 123 053 0157 123 058

0365 310 046 0157 123 054 0157 123 059

0365 310 047 0157 123 055 0157 123 060

0365 310 048 0157 123 056 0157 123 061

0588 000 440 0588 000 442

-0588 000 441

--

--

Ø 1.0

Collet standard and for gas lens

0365 310 028 0157 123 010 0157 123 010

Ø 1.6

Ø 2.4

0365 310 029

0365 310 030

0157 123 011

0157 123 012

0157 123 011

0157 123 077

Ø 3.2

Ø 4.0

Ø 4.8

0365 310 091

--

--

0157 123 013

0157 123 014

--

0157 123 078

0157 123 079

0157 123 074

No 6

No 8

Ø 1.0

Collet body standard

Ø 1.6

Ø 2.4

Ø 3.2

Ø 4.0

Ø 4.8

Isolator

Ø 9.8

Extra large gas nozzle

Ø 12.7

for extra large gas lens

No 10 Ø 15.9

No 12 Ø 19.0

Short Ø 24.0

Ø 2.4

Extra large collet body

Ø 3.2

with gas lens

Ø 4.0

Ø 4.8

Isolator

0365 310 037 0157 123 015 0157 123 081

0365 310 038 0157 123 016 0157 123 081

0365 310 039 0157 123 017 0157 123 081

0365 310 090 0157 123 018 0157 123 082

--

--

0157 123 019

0157 123 019

0157 123 082

0157 123 082

0366 960 017 0366 960 016 0366 960 018

0157 123 088 0157 123 088 0157 123 088

-0157 123 089 0157 123 089

--

--

--

0588 000 438

0157 123 098

0588 000 437

0588 000 438

0157 123 098

0588 000 437

0157 123 085 0157 123 085 0157 123 103

-0157 123 086 0157 123 103

--

--

--

0157 123 087

0157 123 087

0366 960 021

0157 123 105

0157 123 105

0157 123 076 bg19wear

-- 21 --

Edition 2007--05--30

Accessories Äîïîëíèòåëüíûå ïðèíàäëåæíîñòè

Ordering no.

Denomination Notes

Protective Cable

0366 960 049 Protective cable cover with zipper

0366 960 050 Protective cable cover with zipper

0366 960 066 Spot welding set for

TXH 150, TXH 150F, TXH 150V, TXH 200, TXH 200V,

TXH 200F

Gas nozzle

0368 846 880 Accesory kit for

TXH 120V, TXH 250W

0368 846 881 Accesory kit for TXH 150, TXH 150F, TXH 200,

TXH 200V, TXH 200F

0368 846 882 Accesory kit for TXH 400W

3.6 m

7.2 m

ø 6.4, 8.0, 9.8, 11.2 and 12.7

Contains collets, collet body, nozzles, back caps

Contains collets, collet body, nozzles, back caps

Contains collets, collet body, nozzles, back caps

Extension cable OKC connection

0466 705 880 Extension cable gas cooled

0466 705 882 Extension cable gas cooled

0466 705 881 Extension cable water cooled

0466 705 883 Extension cable water cooled

TIG adaptors

0459 491 912 Adaptor kit RA T1 for TXH remote

0466 807 880 Adaptor central / OKC connection

0155 716 880 Flow meter

0365 803 001 Water quick coupling

0365 803 002 Water quick coupling

8 m, max current 200 A

16 m, max current 200 A

8 m, max current 400 A

16 m, max current 400 A

A (incl. holder and 0.25 m cable )

B

male female

A

bg19s010

-- 22 --

Edition 2007--05--30