Swan SI-100E ice shaver Instruction manual

Below you will find brief information for ice shaver SI-100E. The Swan ice shaver SI-100E is designed to shave block ice into fine, fluffy shavings that are perfect for making shaved ice drinks. It features a powerful motor and a sharp blade that can shave ice quickly and efficiently. The SI-100E also includes a drip tray to catch any melted ice.

PDF

Document

for Block Ice

Thank you for purchasing our Swan Ice Shaver.

Please read the instruction manual before using the machine.

WARNING

POTENTIAL RISK OF FIRE, ELECTRIC

SHOCK AND PERSONAL INJURY EXISTS.

CHECK WIRING AND SET PRONGS INTO

ICE BLOCK FIRMLY TO AVOID INJURY.

CAUTION – EXPOSED SHARP

OBJECTS INSIDE.

HAZARDOUS MOVING PARTS

DO NOT OPERATE WITH

COVER OPEN.

CAUTION

Read the following instructions carefully before use. Do not fail to observe this.

•

Children or person who do not thoroughly understand the product should not be allowed to use it.

•

Use single phase 120V power source.

•

Place the machine on a strong and flat horizontal surface or location where dripping water is of no problem.

•

The blade as well as the spikes are very dangerous. They must be handled with extreme care.

•

Place the block ice on center of the shaving disc with the flat side up and be sure the spikes on the block ice holder are deeply embedded in the ice before use. Imperfect placement or down pressure on the block ice will cause the ice to fly out which is extremely dangerous.

•

Ice stored in refrigerator should not be used immediately for shaving as it will damage the blade. Let the ice to thaw and become semi-transparent before use.

•

Do not pour water on the machine or dip it in water.

•

As the cover of the product is made of plastic, do not place it where the product is exposed to direct sunlight or near heating equipment or use paint thinner or similar type of product to clean the cover as these products will disfigure the cover.

USING DIRECTION

Use machine on a firm stand or counter.

Replace or sharpen blade at least 2 or 3 times a season.

Lubricate Main Shaft from time to time.

Ice stored in refrigerator should not be used immediately for shaving as it will damage the blade. Let the ice thaw and become semi-transparent before use.

DIRECTIONS BEFORE USE

The Ice Block Holder Crank is detached from the machine and packed together so it must be installed.

•

Insert Ice Block Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in center.

OPERATING DIRECTIONS

BLADE ADJUSTMENT

1. The Blade is recessed below the surface of the Shaving Disc when the Blade Adjustment Dial is turned to 0.

2. To raise the Blade, slowly turn the Blade Adjustment Knob left.

3. Set the Blade Adjustment Dial on 1 for fine shaving and 6 for roughest shaving.

•

THE DIAL WILL INDICATE 0 WHEN THE BLADE ADJUSTMENT KNOB IS TURNED RIGHT

ALL THE WAY AND STOPS.

BRAKE ADJUSTMENT

Adjust when shaving is unsatisfactory. (For others, see Trouble Shooting Guide)

1. When the Ice Block Holder Crank turns very lightly, turn Brake Adjustment Screw clockwise with screw driver.

2. When the Ice Block Holder Crank turns very heavily, turn Brake Adjustment Screw counterclockwise with (-) screw driver.

(Note: The Brake is adjusted when shipped out of the factory so do not meddle with it.)

PROTECTOR

A Push Button Switch (Protector) is located on the left side of the Head Cover. If something is wrong with the blade section or revolving section, the machine will automatically stop to prevent overheating and damage the motor. In such case, turn off the Power Source Switch (Disconnect the plug) and after the cause is removed. Plug in the cord and push the protector. The Motor will automatically start again.

TO REPLACE DAMAGED PRONG

As the 4 Slotted screw heads as well as the seam between the plastic and the Ice Block Holder base plate is sealed with silicone, be sure to seal after the replacement.

TO MAINTAIN SANITATION WITHOUT TOOLS

For periodic cleaning of the Shaving Disc as well as adjacent area in the food zone, removal is possible as follows.

1. By removing the 4 thumb-screws located on the underside of the plate, the Shaving Disc can be easily removed by pushing it up.

2. To clean the Shaving Disc Frame and the adjacent area, remove the 4 thumb-screws holding the Front Cover (2 thumb-screws on each side), then pull the Front Cover towards the user to remove. The entire food zone can be easily cleaned.

REPLACEMENT BLADE

1. Turn the Blade Adjustment Knob right all the way until it stops.

2. Unscrew the two Phillips-screws. Remove the Blade Holder and blade.

IMPORTANT: DO NOT MEDDLE WITH THE CENTER SLOTTED SCREW.

3. Place the new Blade accurately on the Standard Level Guide Screws on the Blade Support.

4. Put on the Phillips-screw and slowly screw it on so the blade will not lift up from the Standard

Level Guide Screws. Screw it on tight.

•

If both ends of the Blade is not accurately set on the Standard Level Guide Screws, the ice will not shave satisfactorily. In such cases, use something flat and lightly press down the

Blade from the surface of the Shaving Disc, then tighten the Phillips-screws.

STORAGE AFTER SEASON

Wipe off moisture with piece of cloth, then wipe again with dry piece of cloth. Remove Blade, clean and lubricate with cooking oil, then wrap in oil paper before storage. Remove all soiled oil from the Main Shaft and lubricate with grease approved by FDA for the lubrication of food processing machinery. Do not use cooking oil.

•

Specifications are subject to change without notice for further design and performance improvement.

SPECIFICATIONS

Dimensions :

Weight

Shaving Capacity

Motor

Power Requirement :

Accessories :

25-3/4” high x 11-1/8” wide x 15-1/8” deep

61.7 lbs.

4.84~5.5 Lbs./min.

115V, 200W

210W, 60Hz

Spare Blade (1), Grease oil (1), Drain Hose (1)

TROUBLE SHOOTING GUIDE

STERILIZATION

To maintain sanitation of the under mentioned parts

Do not fail to sterilize in a sterilization solution.

(12) BLADE (22) BLADE HOLDER (17) DRIP TRAY

EXAMPLE

Put Blade, Blade Holder and screws inside the Drip Tray, then place this tray inside a vessel and pour in proper quantity of sterilization solution. We recommend this process be carried out after closing shop in preparation for the next day’s work.

PARTS LIST

SWAN ICE SHAVER NEW MODEL SI-100E

(for Block Ice)

PARTS No.

PARTS NAME

Main Shaft Handle

Gear Box Cap

Worm Gear

Gear Box

Worm Gear Rubber

Brake Adjustment Hole Plug

Main Shaft

Polycarbonate Shield

Ice Block Holder Cover

Shaving Disc with Frame

Head Stock Under Cover

Blade

Blade Support

Cutter Block Pin

One Touch Spring

Blade Adjustment Knob

Drip Tray

Motor Cover Rubber

Head Cover

Motor

Brake Worm Gear

Blade Holder

Head Stock

Main Frame Cover

Frame

Rear Guard F Stopper

Rear Guard M Stopper

Frame

Front Panel

Base

Rubber Feet

Gear Box Rubber

Switch Cover

Protector

Motor Switch

SS Worm

Brake Shoe Bracket

Worm Spring

Brake Shoe

Rubber

OR-627

Fuzisoku ET115A

S45-C

FC-20

SWP

Worm Shaft Bracket

Ice Block Holder Crank

Ice Block Holder

Grease Oil

FC-20

Duracon. SUS

Grease Oil

Plug W/C Cord

White Thumb Screws Long/Short SS. ABS

Drain Hose PVC

MATERIAL

FC-20

C5191-B

FC-20

Rubber

S35C-D

Polycarbonate

AC4A

AC7A

P.P.

SUS

Brass

SUS304

SUS304. ABS

ABS

Rubber

ABS

115V 60Hz

FC-20

SUS304

FC-20

ABS

SS400

SUS304

SS400

ABS

FC-20

Rubber

REMARKS

memo

DISTRIBUTED BY

MANUFACTURED BY

Ikenaga Iron Work’s Co., Ltd.

Osaka, Japan

Hello! I am an AI chatbot specifically trained to assist you with the Swan SI-100E Instruction manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

Shaves block ice
Powerful motor
Sharp blade
Drip tray
Adjustable blade
Safety features
Easy to clean
Durable construction

Frequently asked questions

To adjust the blade, slowly turn the Blade Adjustment Knob to the left. The Blade Adjustment Dial will indicate the level of fineness or coarseness of the shavings.

If your ice shaver stops working, first check the Power Source Switch to make sure it is turned on. If the switch is on, then check the Protector Switch to see if it has been activated. To reset the Protector Switch, press the button on the left side of the Head Cover.

To clean the Shaving Disc and adjacent area, remove the 4 thumb-screws holding the Front Cover (2 thumb-screws on each side), then pull the Front Cover towards the user to remove. You can also remove the Shaving Disc by removing the 4 thumb-screws located on the underside of the plate and pushing it up.

To replace the blade, first turn the Blade Adjustment Knob all the way to the right until it stops. Then, unscrew the two Phillips-screws and remove the Blade Holder and blade. Place the new Blade accurately on the Standard Level Guide Screws on the Blade Support and tighten the Phillips-screws.