advertisement
Electronic Thermo-Hygrometer
COM
Model: ETHG912
USER MANUAL
EN
INTRODUCTION
This thermo-hygrometer has been designed specifically with performance and ease-of-use in mind. This thermo-hygrometer is made to the highest quality standards using precision electronic components and should give you many years of trouble free use.
Please read the User’s Guide carefully before use to ensure you get the best out of your new thermo-hygrometer.
INDOOR THERMOMETER WITH RELATIVE
HUMIDITY READING
The thermo-hygrometer is specially designed for accurate reading of indoor temperature and relative humidity. It can help you control humidity and your heating / cooling system, for an ideal living environment.
FEATURES
Easy Operation: Displays the temperature and relative humidity reading automatically.
Error-free Reading: Digital display system ensures clear, error-free reading at a glance.
Temperature compensation: Assures accurate relative humidity measurement unaffected by temperature change.
Comfort indicator: The comfort indicator lets you know when your environment is in the ideal range for both relative humidity and temperature.
Mounting: Table or wall-mount option.
INSTALLING THE BATTERY
The thermo-hygrometer is powered by one piece UM-4 or
AAA size battery. Follow the below steps to install or replace the batteries:
1. Open the battery cover on the back of the unit.
2. Insert the battery as indicated by the polarity symbols (+/-) marked inside the battery compartment.
3. Replace the battery cover.
NOTE
1. When you install or replace the battery, it takes time to reset both the temperature and humidity data.
The display will show ‘---°C’ and ‘88%’ for 1 to 2 seconds, then it shows the updated temperature and humidity reading.
2. When the display becomes dim, replace the battery.
Indicator on the display
Temperature
Range
Humidity
Range
COM
WET
DRY
20ºC to 25ºC
(68ºF to 77ºF)
40% RH to
70% RH
(Comfort)
0ºC to 50ºC
(32ºF to 122ºF)
Over
70% RH
0ºC to 50ºC
(32ºF to 122ºF)
Below
40% RH
Shows the current environment
Ideal range for both relative humidity and temperature
Contains excess moisture.
(Too wet)
Contains inadequate moisture.
(Too dry)
NOTE Some environments may exceed the above standards. When this happens, COM, WET or DRY will not appear on the display.
USE OF SUPPLIED STAND
You can set your thermo-hygrometer on a table as follows:
P/N: 086L001499-230 REV1
1/2
ETHG912 IROX R-2.indd 1
1. Remove the plastic bracket.
2. Flip out the built-in plastic stand on the back side of the thermo-hygrometer.
MOUNTING THE THERMO-HYGROMETER
Follow these steps to mount the thermo-hygrometer:
1. The thermo-hygrometer has a plastic bracket with sticker pad on the back side of the bracket.
Peel off the protective paper on the sticker pad for attaching the bracket on a wall.
2. Slide the thermo-hygrometer down into the holder unit until it locks into place.
NOTE Do not place the thermo-hygrometer in direct sunlight or in area exposed to heavy saturation.
PRECAUTIONS
When handled properly, this unit is engineered to give you years of satisfactory service. Here are a few product care instructions:
1. Do not immerse the unit in water. If the unit comes in contact with water, dry it immediately with a soft lint-free cloth.
2. Do not clean the unit with alcohol containing detergent, abrasive or corrosive materials. Abrasive cleaning agents may scratch the plastic parts and corrode the electronic circuit.
3. Do not subject the unit to excessive force, shock, dust, temperature, or humidity. Such treatment may result in malfunction, a shorter electronic life span, damaged batteries, or distorted parts.
4. Do not tamper with the unit’s internal components. Doing so will terminate the unit’s warranty and may cause damage.
The unit contains no user-serviceable parts.
5. Only use new batteries as specified in this instruction manual.
Do not mix new and old batteries as the old batteries may leak.
6. Read this instruction manual thoroughly before operating the unit.
SPECIFICATIONS
Temperature: 0°C to 50°C (32°F to 122°F)
Measuring Range
Temperature:
Resolution Humidity:
1°C (2°F)
25% RH to 95% RH at 25°C (77°F)
Measuring Range Humidity: 1% RH
Resolution Power Source: One (1) UM4 (AAA) battery
Battery Life:
Dimension:
Weight:
Approx. 6 months
93 x 62 x 15 mm (H x W x D)
80 g (without battery)
CAUTION
• The contents of this manual and the product specifications are
subject to change without further notice.
• The technical specifications of this product are subject to
change without notice.
• The contents of this manual may not be reproduced without
the permission of the manufacturer.
Termoigrometro elettronico
Modello: ETHG912
Manuale d’uso
IT
INTRODUZIONE
Questo termoigrometro è stato progettato per offrire prestazioni ottimali e una estrema facilità d’uso.Questo termoigrometro
è conforme ai migliori standard qualitativi ed è costituito dai migliori componenti elettronici di precisione per garantire anni di corretto utilizzo.
Leggere attentamente il manuale d’uso prima dell’uso per ottenere il massimo risultato dal nuovo termoigrometro.
TERMOMETRO PER INTERNI CON LETTURA
DELL’UMIDITÀ RELATIVA
Il termoigrometro è stato progettato per una rilevazione accurata della temperatura interna e dell’umidità relativa per un ambiente ideale.
FUNZIONI
Il termoigrometro rileva e visualizza automaticamente i valori della temperatura e dell’umidità relativa.
Il prodotto è dotato di un sistema con display digitale che garantisce una lettura accurata e chiara delle informazioni.
Garantisce un’accurata misurazione dell’umidità relativa non influenzata dai cambiamenti di temperatura.
L’indicatore di benessere informa sulle condizioni ambientali che rientrano nell’intervallo ideale per quanto riguarda umidità relativa e temperatura.
Il termoigrometro può essere utilizzato appoggiato su una superficie piana o appeso ad una parete.
INSTALLAZIONE DELLE BATTERIA
Il termoigrometro è alimentato da una batteria UM-4 o AAA. Per installare o sostituire la batteria, seguire i seguenti passaggi:
1. Aprire il coperchio del vano batteria sul retro dell’unità.
2. Inserire la batteria rispettando i simboli delle polarità (+/-) riportati all’interno del vano batteria.
3. Riposizionare il coperchio del vano batteria.
NOTA
1. Dopo l’installazione o la sostituzione della batteria, è necessario attendere alcuni istanti per il ripristino dei dati relativi alla temperatura e all’umidità.
Sul display verrà visualizzato: ºC’ e ‘88%’ per 1 o 2 secondi e quindi i valori aggiornati della temperatura e dell’umidità.
2. Quando il display si affievolisce, sostituire la batteria.
Indicatore sul display
Intervallo temperatura
Intervallo umidità
Condizione ambientale corrente
BEN Da 20ºC a 25ºC
(da 68 ºF a
77ºF)
Da 40% RH a
70% RH
(Benessere)
Intervallo ideale per l’umidità relativa e la temperatura
Oltre 70% RH Molta umidità.
(Troppo umido)
UMIDO Da 0ºC a 50ºC
(da 32ºF a
122ºF)
SECCO Da 0ºC a 50ºC
(da 32ºF a
122ºF)
Inferiore a
40% RH
Scarsa umidità.
(Troppo secco)
NOTA Quando i valori rilevati non sono compresi negli intervalli sopra riportati, il prodotto non riporta alcuna indicazione.
UTILIZZO DEL SUPPORTO FORNITO IN
DOTAZIONE
È possibile posizionare il termoigrometro su un tavolo nel modo seguente:
1. Rimuovere la graffa di plastica.
2. Aprire il supporto di plastica incorporato sul retro del termoigrometro.
MONTAGGIO DEL TERMOIGROMETRO
Per montare il termoigrometro, seguire i passaggi seguenti:
1. Il termoigrometro è dotato di un supporto di plastica che presenta un cuscinetto adesivo sul retro. Togliere il foglio adesivo dal cuscinetto per fissare il supporto al muro.
2. Far scorrere il termoigrometro verso il basso all’interno del supporto finché non scatta in posizione.
NOTA Non esporre il termoigrometro alla luce diretta del sole o in un ambiente troppo saturo.
PRECAUZIONI
Se manipolata correttamente, questa unità è stata progettata per offrire anni di funzionamento soddisfacente. Leggere le istruzioni seguenti sulla manutenzione del prodotto:
1. Non immergere l’unità nell’acqua. Se l’unità entra in contatto con l’acqua, asciugarla immediatamente con un panno asciutto.
2. Non pulire l’unità con alcol, detergenti o materiali abrasivi o corrosivi. Gli agenti abrasivi possono graffiare le parti in plastica e corrodere il circuito elettronico.
3. Non sottoporre l’unità a umidità, temperature, polvere, scosse e sforzi eccessivi per evitare malfunzionamenti oppure per non abbreviare la durata dei componenti elettronici, per non danneggiare le batterie o deformare alcuna parte.
4. Non manomettere i componenti interni dell’unità. Ciò potrebbe invalidare la garanzia e danneggiare il prodotto. L’unità non contiene parti riparabili dall’utente.
5. Utilizzare solo batterie nuove del tipo specificato nel manuale di istruzioni. Non mescolare batterie vecchie e nuove. Le batterie vecchie potrebbero perdere liquidi.
6. Leggere attentamente il manuale di istruzioni prima di mettere in funzione l’unità.
SPECIFICHE
Intervallo di misurazione della temperatura:
Risoluzione della temperatura: da 0 °C a 50 °C
(da 32 °F a 122 °F)
1 °C (2 °F)
Intervallo di misurazione dell’umidità: da 25% RH a 95%
RH a 25 °C (77 °F)
Risoluzione dell’umidità: 1 % RH
Alimentazione:
Dimensioni:
Peso:
Una (1) batteria UM4 (AAA)
93 x 62 x 15 mm (A x L x P)
80 g (senza batteria)
ATTENZIONE
• Il contenuto del manuale e le specifiche del prodotto sono
soggetti a modifiche senza preavviso.
• Le specifiche tecniche del prodotto sono soggette a modifiche
senza preavviso.
• È vietato riprodurre il contenuto di questo manuale senza il
consenso del produttore.
Thermohygromètre Electronique
Modèle: ETHG912
Manuel d’utilisation
FR
INTRODUCTION
Ce thermohygromètre a été conçu avec le souci d’une performance optimale et d’une grande facilité d’utilisation. Ce thermohygromètre a été fabriqué selon les standards de qualité les plus élevés, avec l’utilisation de composants électroniques de précision, pour vous apporter de nombreuses années de satisfaction.
Lisez attentivement ce manuel d’utilisation avant toute première utilisation afin d’utiliser votre nouveau thermohygromètre de façon optimale.
THERMOMÈTRE INTÉRIEUR AVEC MESURE DE
L’HUMIDITÉ RELATIVE
Ce thermohygromètre a été spécialement conçu de façon à permettre une lecture précise de la température intérieure et de l’humidité relative. Il peut vous permettre de contrôler le taux d’humidité relative de votre environnement et par conséquent
évaluer au mieux vos besoins de chauffage / climatisation, pour votre plus grand confort.
CARACTÉRISTIQUES
Facilité d’Utilisation : Affichage automatique de la température et de l’humidité relative.
Mesure de Précision : L’affichage numérique permet une lecture rapide et précise des relevés.
Compensation des Températures : Permet une mesure précise de l’humidité relative, indépendamment des changements de température.
Indice de Confort : L’indice de confort vous indique lorsque l’environnement est idéal sur la base des relevés de la température et de l’humidité relative.
Montage : Sur dessus de table ou mural.
INSTALLATION DE LA PILE
Votre thermohygromètre est alimenté par une pile de type UM-
4 ou AAA. Suivez les instructions suivantes pour installer ou remplacer la pile :
1. Ouvrez la trappe du compartiment à piles au dos de l’appareil.
2. Insérez la pile en respectant les indications de polarités (+/-)
à l’intérieur du compartiment.
3. Remettez la trappe du compartiment à piles en place.
NOTE :
1. Lorsque vous installez ou remplacez la pile, les données concernant la température et l’humidité relative sont réinitialisées.
L’affichage indique : « --°C » et « 88% » pendant 1 à 2 secondes, puis les relevés actualisés de la température et de l’humidité relative s’affichent à l’écran.
2. Lorsque l’affichage s’affaiblit, remplacez la pile.
Indicateur à l’affichage
Températures Humidité relative
Environnement présent
COM
WET
20°C à 25°C
(68°F à 77°F)
0ºC à 50ºC
(32ºF à 122ºF)
40% HR à
70% HR
(Confortable)
Supérieure à
70%
Environnement idéal
Trop humide
DRY 0ºC à 50ºC
(32ºF à 122ºF)
Inférieure à
40%
Trop sec
NOTE :
Certains environnements peuvent ne pas se conformer aux standards décrits ci-dessus. Dans ce cas de figure, les indicateurs
COM, WET ou DRY n’apparaissent pas à l’affichage.
UTILISATION DU SOCLE
Vous pouvez poser votre thermohygromètre sur un dessus de table en procédant comme suit :
1. Enlevez le support en plastique située au dos de l’appareil.
2. Faites basculer le socle en plastique intégré et posez l’appareil sur un dessus de table.
MONTAGE MURAL
Suivez les instructions suivantes pour un montage mural de votre thermohygromètre :
1. L’appareil est équipé au dos d’un support en plastique avec une surface autocollante permettant un montage mural.
Enlevez la feuille de protection au dos du support et collez le support sur le mur.
2. Faites glisser le thermohygromètre dans son support jusqu’à ce qu’il s’enclenche en position.
NOTE :
Ne placez pas le thermohygromètre en plein soleil ou dans lieux très humides.
PRÉCAUTIONS D’EMPLOI
Cet appareil a été conçu de façon à vous apporter de nombreuses années de satisfaction, sous réserve toutefois que vous en preniez soin. Vous trouverez ci-dessous quelques précautions d’emploi, ainsi que quelques conseils utiles pour l’entretien de votre appareil.
1. Ne plongez pas l’appareil sous l’eau. Si l’appareil vient à tomber dans l’eau, séchez-le immédiatement avec un chiffon doux qui ne peluche pas.
2. Ne nettoyez pas le corps de l’appareil avec des détergents contenant de l’alcool ou d’autres substances corrosives.
Des détergents abrasifs peuvent endommager les pièces en plastiques et corroder les circuits électroniques.
3. Ne faites subir aucun choc à cet appareil et gardez-le à l’abri de l’humidité et des températures extrêmes, au risque de causer un mauvais fonctionnement de l’appareil, de réduire la durée de vie des circuits électroniques, d’endommager les piles ou de déformer certaines pièces.
4. Ne touchez pas aux composants internes de cet appareil, au risque d’endommager l’appareil et d’annuler votre garantie.
Cet appareil contient des pièces qui ne nécessitent aucune maintenance.
5. Utilisez uniquement des piles du type recommandé dans le manuel d’utilisation. Ne mélangez pas des piles neuves avec des piles usées, au risque de causer un écoulement des piles.
6. Lisez attentivement le manuel d’utilisation avant toute première utilisation de cet appareil.
SPÉCIFICATIONS
Températures : 0°C à 50°C (32°F à 122°F)
Précision des relevés de température :
Humidité relative :
1°C (2°F)
25% HR à 95% HR
à 25°C (77°F)
Précision des relevés de l’humidité :
Source d’alimentation :
1% HR
Une (1) pile UM-4 (AAA)
Durée de vie de la pile : Environ 6 mois
Dimensions :
Poids :
93 x 62 x 15 mm (H x L x P)
80g (sans la pile)
ATTENTION
• Le contenu de ce manuel d’utilisation et les spécifications du
produit sont sujets à modification sans avis préalable.
• Les spécifications techniques de ce produit sont sujettes à
modification sans avis préalable.
• Le contenu de ce manuel ne peut être reproduit sans la
permission du fabriquant.
4/28/06 1:06:25 PM
Eletronisches Thermo-Hygrometer
Modell: ETHG912
Bedienungsanleitung
DE
EINFÜHRUNG
Bei der Entwicklung dieses Produktes haben wir speziell auf einfachste Bedienung bei hoher Leistung geachtet. Produkten wurden auch hier nur Präzisionsbauteile verwendet. Dadurch wird ein hoher Qualitätsstandard gewährleistet, der Ihnen ein jahrelanges, fehlerfreies Funktionieren des Gerätes erlauben wird. Bitte lesen Sie unsere Bedienungsanleitung sorgfältig durch, bevor Sie das Gerät in Betrieb nehmen. Dadurch ist auch der richtige Einsatz sichergestellt.
INNENRAUM-THERMOMETER MIT
MESSMÖGLICHKEIT FÜR RELATIVE
LUFTFEUCHTIGKEIT
Dieses Thermo-Hygrometer wurde speziell für die genaue Messung von Innentemperaturen und relativen
Luftfeuchtigkeitswerten geschaffen. Das Gerät ermöglicht
Ihnen dadurch die Regelung der Luftfeuchtigkeit und der
Raumtemperatur mittels Ihres Heiz-/Kühl – Systems, so dass
Sie stets optimale Bedingungen in Ihrer Wohnumgebung genießen können.
FUNKTIONSMERKMALE
Einfache Bedienung: Zeigt automatisch die Raumtemperatur sowie die relative Luftfuechtigkeit an.
Fehlerfreie Ablesung: Digitales Anzeigesystem garantiert fehlerfreies Ablesen auf einen Blick.
Te m p e r a t u r k o m p e n s a t i o n : G a r a n t i e r t g e n a u e
Luftfeuchtigkeitsmessung - unabhängig vonTemperaturschw ankungen.
Komfort-Anzeige: Die Komfort-Anzeige zeigt an, wenn in
Ihrem Wohnraum ideale Luftfeuchtigkeits – und Temperatur-
Bedingungen herrschen.
Aufstellung : Tischaufstellung oder Wandaufhängung
EINLEGEN UND AUSWECHSELN DER
BATTERIEN
Dieses Thermo-Hygrometer wird durch eine Batterie des Typs
UM-4 oder “AAA” mit Strom versorgt.
Gehen Sie beim Einlegen oder Auswechseln der Batterien wie nachfolgend beschrieben vor:
1. Öffnen Sie das Batterienfach an der Rückseite des
Gerätes.
2. Legen Sie die Batterien entsprechend den Polarisierungsangaben (+/-) ein, wie im Inneren des Batterienfachs angegeben
3. Schließen Sie das Batterienfach wieder.
HINWEIS
1. Nachdem Sie die Batterien erstmals eingelegt oder ausgewechselt haben, benötigt das Gerät einige Zeit, um eine Rücksetzung der Temperatur- und Luftfeuchtigkeitsanzeige zeige durchzuführen. In der Anzeige erscheint ca. 2
Sekunden lang “--°C” und “88%”. Anschließend erscheinen die aktuellen Temperatur – und Luftfeuchtigkeitswerte.
2. Sobald die Anzeige schwächer wird, sollten die Batterien ausgewechselt werden.
HINWEIS ZUM SCHUTZ UNSERER UMWELT /
BATTERIEENTSORGUNG
Batterien gehören nicht in den Hausmüll. Als Verbraucher sind Sie gesetzlich verpfl ichtet, gebrauchte Batterien zurückzugeben. Sie können Ihre alten Batterien bei den öffentlichen Sammelstellen in Ihrer Gemeinde oder überall dort abgeben, wo Batterien der betreffenden Art verkauft werden.
ABLESEN DER LUFTFEUCHTIGKEIT UND DER
KOMFORT-ANZEIGE
Das Gerät zeigt Ihnen die temperatur-korrigierten
Luftfeuchtigkeitswerte an. Zugleich veranschaulichen die
Anzeigen “COM”, “WET” oder “DRY”, ob die aktuellen
Raumbedingungen angenehm, zu feucht oder zu trochen sind.
Die Komfort-Anzeigen erscheinen entsprechend den nachfolgend aufgeführten Messergebnissen in der Anzeige:
Anzeige
Indikator
Temperatur -
Bereich
Luftfeuchtigkeits-
Bereich
COM
WET
20ºC bis 25ºC
(68ºF bis 77ºF) keit
40% - 70%
Relative
Luftfeuchtigkeit
0ºC bis 50ºC
(32ºF bis 122ºF)
Über 70%
Relative
Luftfeuchtigkeit
Zeigt an, wie die
Raumtemperatur-und
Luftfeuchtigkeits- bedingungen einzuschätzen sind:
Idealer Bereich sowohl für relative
Luftfeuchtigkeit als auch Temperaturen
Luftfeuchtigkeit ist zu hoch
DRY 0ºC bis 50ºC
(32ºF bis 122ºF)
HR - 40% Luftfeuchtigkeit ist niedrig
P/N: 086L001499-230 REV1
2/2
ETHG912 IROX R-2.indd 2
HINWEIS In eingen Räumen werden die oben aufgeführten
Grenzwerte über – oder unterschritten, und die Anzeigen COM,
WET oder DRY erscheinen in der Folge nicht.
DER EINSATZ DES MITGELIEFERTEN
STÄNDERS
Sie können Ihr Thermo-Hygrometer wie nachfolgend beschrieben auf einem Tisch aufstellen:
1. Nehmen Sie die Plastikklammer ab.
2. Klappen Sie den integrierten Plastikständer an der Rückseite des Gerätes heraus.
WANDAUFHÄNGUNG DES THERMO-
HYGROMETERS
Befolgen Sie die nachfolgend beschriebenen Schritte, um das
Gerät an der Wand aufzuhängen:
1. Das Thermo-Hygrometer ist mit einer Halteklammer und einer
Klebefl äche auf der Rückseite der Klammer versehen. Ziehen
Sie die Schutzfolie von der Klebefl äche ab, bevor Sie die
Klammer an der Wand befestigen.
2. Schieben Sie das Thermo-Hygrometer abwärts auf die
Klammer, so dass dieses einrastet.
HINWEIS Das Thermo-Hygrometer sollte keiner direkten
Sonneneinstrahlung und Feuchtigkeit ausgesetzt sein.
VORSICHTSMASSNAHMEN
Dieses Gerät wird Ihnen bei schonender Behandlung viele Jahre nützlich sein. Beachten Sie dennoch die wenigen nachfolgenden
Vorsichtsmaßnahmen:
1. Tauchen Sie das Gerät nicht in Wasser.
2. Reinigen Sie das Gerät niemals mit scheuernden oder scharfen Reinigern. Diese könnten die Plastikteile beschädigen, und die elektronischen Schaltkreise korrodieren.
3. Setzen Sie das Gerät nicht irgendwelcher Gewalteinwirkung,
Erschütterungen, Staub, extremen Temperaturen oder
Feuchtigkeit aus, da dadurch Funktionsstörungen, kürzere
L e b e n s d a u e r u n d B a t t e r i e s c h ä d e n s o w i e
Gehäuseverformungen verursacht werden können.
4. Nehmen Sie keine Änderungen an den inneren Komponenten des Gerätes vor. Dadurch erlischt die Garantie für das Gerät und es können andere Schäden verursacht werden. Im
Inneren des Gerätes befi nden sich keine Teile, die vom
Benutzer selbst gewartet werden müssen.
5. Ve r w e n d e n S i e n u r n e u e B a t t e r i e n d e s i n d e r
Bedienungsanleitung angegebenen Typs. Mischen Sie niemals alte und neue Batterien, da alte Batterien auslaufen können.
TECHNISCHE DATEN
Temperatur- Messbereich: 0°C bis 50°C (32°F bis 122°F)
Aufl ösung der
Temperaturanzeige:
Luftfeuchtigkeits-
Messbereich:
1°C (2°F)
26% bis 95% Relative
Luftfeuchtigkeit bei 25°C (77°F)
Aufl ösung der
Luftfeuchtigkeitsanzeige: 1% Relative
Luftfeuchtigkeit
Abmessungen: 93 x 62 x 15mm (H x T x W )
Gewicht: 80 Gramm (ohne Batterie)
VORSICHT
• Aufgrund von Einschränkungen der Druckmöglichkeiten kann
die Darstellung der Anzeige in dieser Bedienungsanleitung
von der tatsächlichen Anzeige abweichen.
• Der Inhalt dieser Bedienungsanleitung darf nicht ohne die
Zustimmung des Herstellers vervielfältigt werden.
• Änderungen vorbehalten
Termo-Higrómetro
Modelo: ETHG-912
Instrucciones de Funcionamiento
ES
INTRODUCCION
Este está hecho con los más altos niveles de calidad y utilizando componentes electrónicos de gran precisión que se espera le facilitarán su uso, sin problema alguno, por mucho tiempo.
Por favor, lea atentamente las instrucciones antes de utilizarlo con el fi n de obtener el mayor rendimiento de su nuevo modelo.
TERMÓMETRO DE INTERIOR CON LECTURA
DE HUMEDAD RELATIVA
El Termo-higrómetro está especialmente diseñado para la medición precisa de la temperatura interior y la humedad relativa. Puede ayudarle a controlar la humedad y el sistema de calefacción / refrigeración, para un ambiente ideal.
CARACTERÍSTICAS
Fácil operación: Muestra la temperatura y la medición de la humedad relativa automáticamente.
Lectura libre de errores: Sistema de pantalla digital, que asegura una medición clara y libre de errores de un vistazo.
Compensación de: Asegura una medición correcta de la temperatura humedad relativa sin afectarle los cambios de temperatura.
Indicador de confort: El indicador de confort le hace saber cuando el ambiente está a un nivel ideal tanto para la humedad relativa como para la temperatura.
Montaje: Montaje en mesa o en pared.
INSTALACIÓN Y REEMPLAZO DE LAS PILAS
El termo-higrómetro funciona con una sola pila de tamaño UM-4 o AAA. Siga estos pasos para instalar o reemplazar la pila:
1. Abra la tpa del compartimento en la parte trasera de la unidad.
2. Coloque la pila tal como indican los símbolos de polaridad
(+ / -) que están marcados dentro del compartimiento de las pilas.
3. Cierre la tapa del compartimento de las pilas.
NOTA
1. Cuando instale o cambie la pila, se necesita algo de tiempo para reiniciar los datos de temperatura y humedad. La pantalla mostrará “--- °C” y “88%” durante 1 o 2 segundos, y entonces mostrará los datos actualizados de temperatura y humedad.
2. Cuando la pantalla no aparezca clara, es un buen momento para cambiar la pila.
CÓMO LEER LOS INDICADORES DE
HUMEDAD RELATIVA Y CONFORT
La unidad muestra la humedad relativa del interior y esta medición está compensada por la temperatura. A la vez, los indicadores de confort – COM, WET o DRY le dirán si el ambiente actual es confortable, demasiado húmedo o demasiado seco.
Los indicadores de confort aparecerán en la pantalla cuando se cumplan las siguientes condiciones:
Indicación en la pantalla
COM
WET
DRY
Nivel de temperatura
20ºC a 25ºC
(68ºF a 77ºF)
0ºC a 50ºC
(32ºF a 122ºF)
0ºC a 50ºC
(32ºF a 122ºF)
Nivel de humedad
40% RH a
70% RH
Màs de
70% HR
Menos de
40% HR
Estado del ambiente actual
Nivel ideal tanto para tempertura como para humedad
Humedad excesiva
Humedad inadecuada
NOTA Algunos ambientes pueden exceder los estándares expuestos arriba. En ese caso, no se mostrarán los indicadores
COM, WET o DRY.
USO DEL SOPORTE INCORPORADO
Puedo colocar su termo-higrómetro en una mesa de la forma siguiente:
1. Quite el soporte del plástico.
2. Gire el soporte incorporado hacia la parte posterior del termo-higrómetro.
MONTAJE DEL TERMO-HIGRÓMETRO
Siga estos pasos para montar el termo-higrómetro:
1. El termo-higrómetro tiene un soporte de plástico con una superfi cie adhesiva en la parte posterior. Quite el papel protector de la superfi cie adhesiva para colocar el soporte en la pared.
2. Deslice el termo-higrómetro en el soporte hasta que se coloque en su sitio.
NOTA Coloque el termo-higrómetro lejos de la luz del sol directa y de la saturación alta.
PRECAUCIONES
Este producto está diseñado para ofrecerle años de servicio satisfactorio si lo maneja cuidadosamente. Aquí hay unas pocas precauciones:
1. No lo sumerja en agua
2. No limpie la unidad con materiales abrasivos o corrosivos.
Se puede dañar las partes de plástico y corroer el circuito eléctrico.
3. No someta la unidad a fuerzas excesivas, sacudidas, polvo, temperatura o humedad que puede causar un mal funcionamiento, acortar la duración electrónica, dañar las pilas y distorsionar algunas partes.
4. No juegue con los componentes internos de la unidad. El hacerlo invalidaría la garantía en la unidad y podría causar daños innecesarios. La unidad no contiene partes que puedan utilizarse por el usuario.
5. Use solo pilas nuevas como se especifi ca en el manual del usuario. No mezcle pilas nuevas y usadas ya que las usadas pueden licuar.
6. Lea siempre el manual del usuario por completo antes de usar la unidad.
ESPECIFICACIONES
Nivel de medida de la temperatura: 0°C a 50°C (32°F to 122°F)
Resolución de la temperatura: 1°C (2°F)
Nivel de medida de la humedad:
Resolución de la humedad: 1% HR
25% a 95% HR a 25°C (77°F)
Fuente de alimentación: Una pila (1) LR03 (AAA) de 1,5V
Duracion de las pilas: Aprox. 6 meses.
Dimensiones:
Peso:
93 x 62 x 15 mm
(Altura x Anchura x Profundidad)
80 g (Sin batería)
PRECAUCION
• El contenido de este manual está sujeto a cambio sin aviso
previo.
• Debido a las limitaciones de impresión, las pantallas
mostradas en este manual podrían diferir de la pantalla real.
• Se prohibe reproducir el contenido de este manual sin el
permiso del fabricante.
For more info visit www.irox.com
4/28/06 1:06:28 PM
advertisement