Mattel Perfect Fit Light Stroller Instruction Sheet

Instructions
Perfect Fit" Light Stroller
* Please save these instructions for future reference.
- Adult assembly is required. (Tools are not needed
for assembly.)
* Maximum weight of child: 40 Ibs.
* Maximum height of child: 38 inches
* Maximum storage weight for storage basket: 8 Ibs.
-—— AWARNING:
The safety of your child while in the
Perfect Fit Light Stroller depends on
you! Please read and understand the
following warnings and instructions
before use.
* Never leave your child unattended.
* To prevent serious injury or death from
falls or sliding out. alwavs use the
restraint system.
* Do not carry more than one child at a
time in this stroller.
* Do not carry additional goods or
accessories in or on this stroller, except
in the storage basket as recommended
in the instructions.
* This stroller may become unstable if
the maximum weight of the storage
basket is exceeded. Do not exceed the
maximum weight limit of 8 Ibs. in the
storage basket.
* This stroller may become unstable if
items are hanging from or placed on the
handle. Do not hang shopping bags,
purses or accessories on the handle.
Fisher Price
Model Numbers: 9217, 9218
Message to Parents
Thank vou for nurchasino the Fishor Prico Perfect Fit
Light Stroller, a lightweight stroller designed for parents
and babies on the go! We hope you will find the features
and styling of this Fisher-Price product a perfect fit in
satisfying the needs of both you and baby.
Occasionally a consumer may experience difficulty with
one of our products. If this should happen, please call us,
toll-free, rather than returning the product to the store.
Usually we can solve the problem on the telephone or by
sending you replacement parts. .
If you have any questions about the Perfect Fit Light
Stroiler or would like to order replacement parts,
please call Fisher-Price Consumer Affairs, toll-free at
1-800-432-KIDS (1-800-432-5437) between 8 AM and
6 PM Eastern time, Monday through Friday, or write to:
Fisher-Price, Inc.
Attn: Consumer Affairs
636 Girard Avenue
East Aurora, New York 14052
Hearing-impaired consumers using TTY/TDD
equipment, please call 1-800-382-7470.
Rear Wheel
Rear Wheel Hubcap
Rear Axle with © i
Locking Tabs
/N\ CAUTION.
Please keep small parts and plastic
bags out of children’s reach.
| Assembly
To Unfold
о A
À
Rear Cross Bar
Л MA Frame Latch
fe * Hold the handle with one hand and the rear cross bar
J with the other. Pull the handle and the rear cross bar
|< apart until the frame latches snap into position.
Position the stroller with the frame latches on the floor.
Frame Latch
* Test to be sure both frame latches are secure by lifting
the handle and rear cross bar. The frame latches should
remain locked.
Rear Axle Assembly
O Rear Wheels
ad , e
# * +
`
в
t
1
[J
1
4
|
i +
' 1
t 1
W
4
mn
*
нинниф»>
wu...
Rear Axle
Locking Tab
Locking Tab
» Slide the locking tabs apart so that there is one rear
wheel and one locking tab on each end of the rear axle.
O Locking Tab | Locking Tab
Rear Wheel Retainers
Ч | Storage Basket
Square Opening
Square Opening
» Stand behind the stroller so that the underside of the
storage basket is facing you.
» Position the locking tabs over the rear wheel retainers.
Make sure the locking tabs point down toward the square
openings in the rear wheel retainers.
O Locking Tab Locking Tab
Rear Axle
Groove
Groove
Rear Wheel Retainers
* Place the rear axle in the grooves in the rear wheel
retainers with the locking tabs centered in the rear wheel
retainers.
* Push down firmly on the rear axle near each of the rear
wheel retainers to snap the locking tabs into the rear
wheel retainers. Make sure you hear a snap on both
sides. The rear axle should touch the bottom of the
grooves in the rear wheel retainers.
[LA
==
CH \ | /
Rear Axle
Hubcap Hubcap
» Test to be sure the rear axle assembly is secure by
pulling up lightly on the center of the rear axle. The
locking tabs should remain locked in the rear wheel
retainers.
* Snap a hubcap into the center of each rear wheel.
Front Wheel Assembly
O
Front Wheel Castor
Front Leg
* Slide the open end of a front wheel castor onto one of
the front legs.
©
Moveable Ring À
| )
Pin >
Hole —
E a Front Wheel
- ron
/ i à | Castor
A y
A CJ
+ Twist the moveable ring on the front wheel castor to align
the hole in the moveable ring with the pin on the front leg.
* Push the pin on the front leg in and slide the front wheel
castor over it. The pin should snap into the hole.
* Pull on the front wheel to be sure it is securely attached
to the front leg.
+ Repeat this procedure to assemble the other front wheel
to the Perfect Fit Light Stroller.
Tray Attachment
©
Tray
Exposed
\ |
PIN
* Тит the stroller upright.
+ Place the “C” shaped notch in the end of the tray arm
around the exposed frame tube under the right frame
latch.
Ф A Ÿ Le
Te CNT Frame
Shaped | Latch
Notch | y «a
E A у
No Recessed
| Ae
Tray Arm
* To close the tray, pivot it toward the left frame latch.
* Snap the “U” shaped notch in the end of the tray arm
onto the recessed area below the left frame latch.
One time assembly is now complete.
Operation and Use |
To Unfold
o 5
FA
“WN
Aw
©
Latch
Frame Latches
=
5
f
Y
A
N
IN
ND
Latch Clip
=
Cd
=;
Be
N
77
OR
9
x
6
* Position the stroller upright on its rear wheels. * Testto be sure both frame latches are secure by pushing
* Press on the latch on the side of the stroller to release down on the handie. The frame latches should remain
the latch clip. locked in position.
$9
Tray Operation
Ч Frame Latches
Tray Clip
- To open the tray, pull out on the flexible tray clip and pivot
the tray open. ;
« Grasp the front edge of the tray with one hand to steady
the stroller.
* With your other hand, lift the handle until the frame
latches “snap” into position.
Area
* To close the tray, pivot it toward the left frame latch.
* Snap the “U” shaped notch in the end of the tray arm
onto the recessed area below the left frame latch.
Seat Back Adjustment
Upright
Position
Reclined
Position
* The seat back can be adjusted for baby’s comfort to an
upright or a reclined position.
PLEASE NOTE: Each time you unfold the stroller it will
be in the reclined position.
Seat Back
LU
To raise the seat back:
* Turn the stroller so that the back is facing you.
* Lift the seat back.
* Tuck in any excess fabric on the sides of the raised
seat back.
* Insert the pins on the sides of the seat back into the seat
back latches. Make sure there is no excess fabric
between the pins and the seat back latches.
©
Seat Back
Latch
Thumb Tab
Y
7 mn Back
ИИ Г о \\
To recline the seat back:
* Press on the thumb tab on the seat back latches to
release the pins. |
* Guide the seat back down to the reclined postion.
Restraint Вейс Adjusting the Waist Belts
/N\ WARNING
To prevent serious injury or death,
always use the restraint belts.
pe SE A
—
Free End
To tighten the waist belts: .
* Feed the anchored end of the waist belt up through the
buckle to form a loop O.
* Pull the free end of the waist belt €).
| * Repeat this procedure to tighten the other waist belt.
Waist Belt PLEASE NOTE: After adjusting the waist belts to fit your
child, make sure you pull on them to be sure they are
securely fastened.
— 7 LR NT Free End В
Waist Belt
Crotch
Belt Anchored End
* Open the tray. FreeEnd / JJ“ IS
* Place your child in the Perfect Fit Light Stroller.
* Puli the crotch belt up between your child's legs. To loosen the waist belts:
» Buckle both waist belts to the crotch belt. Make sure you * Feed the free end of the waist belt up through the buckle
hear a click on both sides. to form a loop O.
* Маке sure the waist belts are properly adjusted to fit * Enlarge the loop by pulling on the end of the loop toward
your child. the buckle.
* Pull on the waist belts to be sure they are securely » Pull the anchored end of the waist belt to shorten the free
tastened. end of the waist belt @
* Close the tray. * Repeat this procedure to loosen the other waist belt.
PLEASE NOTE: After adjusting the waist belts to fit your
child, make sure you pull on them to bo sure they ara
securely fastened.
Perfect Fit Cushion Adjustment
The Perfect Fit cushion can be adjusted to surround
baby’s head for added support and extra comfort.
O ——]]l]L]]]]——————]]£ —
— —
© o
qu -
; ol
|
End of Outer Seat
Strap Cushion Strap
To adjust the cushion:
- Turn the stroller so that the back is facing you.
* Unfasten the outer seat cushion strap. Make sure the
ends of the outer seat cushion strap remain snapped
together.
* Pull the end of the outer seat cushion strap to adjust the
Perfect Fit cushion for baby’s comfort and added support.
- When the seat cushion is adjusted to the perfect fit for
your baby, re-fasten the outer seat cushion strap. Make
sure the outer seat cushion strap is securely fastened.
NE.
©
¡ef
Core
Outer Seat
Cushion Strap
177
To relax the cushion:
* Tum the stroller so that the back is facing you.
* Unfasten the outer seat cushion strap. Make sure the
ends of the outer seat cushion strap remain snapped
together.
* Turn the stroller so that the front is facing you.
+ Pull the ruffie on the sides of the seat cushion out to
flatten the Perfect Fit cushion.
* Turn the stroller so that the back is facing you and
re-fasten the outer seat cushion strap. Make sure the
outer seat cushion strap is securely fastened.
Canopy Adjustment To Fold
| Сапору
Frame Latches
* The canopy tan be adjusted up or down.
Rear Wheel Brakes
UNLOCK
» Face the front of the stroller.
Make sure the canopy is in the up position.
* Rotate the bottom of the frame latches outward.
Frame Latches \
Rear Wheel Rrake Padals
To lock the rear wheel brakes:
* Press both brake pedals down until they click into
position. Make sure the brake pedals are pressed
down completely.
* Always set both brake pedals whenever you park the
Perfect Fit Light Stroller.
To uniock the rear wheel brakes:
+ Lift both rear wheel brake pedals until they click into the
unlocked position. + Pull up on the frame latches so that the frame rotates to
the folded position.
+ The latch clip on the stroller will automatically lock to
keep the stroller in the folded position.
Cleaning
Perfect Fit Cushion
The Perfect Fit cushion can be machine washed in cold
water and a mild detergent. Do not use bleach. Tumble -
dry on low heat and remove promptly.
Liner, Canopy, Restraint Belts,
Storage Basket
Surface wash with a mild detergent and water. Do not use
bleach. Rinse clean with water to remove residue.
Tray and Frame
Wash the tray and the frame with a mild soap and water
solution. Do not use harsh or abrasive cleaners. Rinse
clean with water to remove soap residue.
To Remove the Perfect Fit Cushion
O nn —
E na
“ее
Buckle Inner Seat
/ Cushion Strap E
ZA
Vi
Outer Seat Cushion Strap _—
©
Turn the stroller so that the back is facing you.
Unfasten the outer seat cushion strap.
* Unsnap the two sections of the outer seat cushion strap.
* Pull the outer seat cushion strap sections through the
buckle, one section at a time.
Unfasten the inner seat cushion strap.
* Тит the strolier so that the front is facing you.
+ Pull the cushion off of the stroller.
To Replace the Perfect Fit Cushion
о
Quter and
Inner Seat
Cushion
Straps
O Inner Seat Cushion Straps
AN
2 vv
Crotch Belt
Waist Belts
VA
* Turn the stroller so the back is facing you.
* Fasten the inner seat cushion straps. Make sure the inner
- Turn the stroller so that the front is facing you. seat cushion straps are securely fastened.
* Place the Perfect Fit cushion in the stroller.
* Pull the crotch belt up through the slot in the cushion.
* Pull the waist belts up through the sides of the cushion. © Outer Seat Cushion Straps
* insert the inner and outer seat cushion straps through _
the slots in the seat back liner.
* Feed-the outer seat cushion straps through the buckle,
one strap at a time.
* Snap the ends of the two outer seat cushion straps
together.
« Adjust the Perfect Fit cushion for baby’s comfort and
fasten the outer seat cushion straps. -
- Make sure the outer seat cushion straps are securely
fastened. ;
©1995 Fisher-Price, Inc., East Aurora, New York 14052 9217, 9218 1 70010-9931
Fisher-Price
Supplemental Instructions
Perfect Fit" Light Stroller Latch
to ensure that your stroller stays securely folded during storage.
Please save these instructions for future reference.
No tools are needed for assembly.
Model Number: 79217
ha vet
AS Snap
AN
VE \ VW A
bl >
EN Liner
Ne
Please Note: This is a permanent attachment. Please
read and follow these instructions carefully.
~
* Wrap the female end of the strap around the stroller handle
between the webbing and the liner and snap together.
To Fold the Stroller
<
* Face the front of the stroller.
* Make sure the canopy is in the up position.
* Rotate the bottom of the frame latches outward.
J
OX
« … Latches
CT, N
J
* Pull up on the frame latches so that the frame rotates to the
folded position.
* Wrap the male end of the strap around the rear leg of the
stroller and fasten the buckle to keep your Perfect Fit
Stroller folded for storage. :
Questions? We'd like to hear from you!
Call Fisher-Price Consumer Affairs, toll-free at 1-800-432-KIDS, 8 AM - 6 PM EST Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470. Or, write to: Fisher-Price Consumer Affairs, 636 Girard Avenue, East Aurora, New York 14052.
© 1996 Fisher-Price, Inc., East Aurora, New York 14052
79217 1 70217-0071