Samsung WD8754CJF/XTC Quick Guide

quick guide
Call 1-800-726-7864
troubleshooting
Water usage
• The half of laundry (8 lbs) water usage is about 18 liter.
• The water usage is about 50 liter until from washing to 2 rinsing.
• According laundry type, It is different the water usage.
Avoid using too much detergent in your washer as it can lead to over sudsing and detergent residue being left on the
clothes.
When door locked or will not open.
• The door will not open when the water temperature is over 131 ˚F.
The door will not open when the internal water sensor detects the water level is too high. When the water level is too high.
Press the Spin button.
Do not try to force the door open when locked.
This could result in physical injury and, damage to the washer.
Vibration or noise.
• When washing big bulky items that occur noise/vibration or damaged laundry.
• Load is too small. Very small loads (one or two items) may become unbalanced and not spin out completely.
- Add a few towels to improve tumbling and spin performance.
When washing the blanket or sheet
• The blanket must put below 3.5 kg and one sheet in washing machine. Rolling the blanket in a round shape reduces the
unbalance.
• Rugs can bring unbalance and cannot be used. But when mixed well with other laundry, the weight center can be spread
and can be used.
INFORMATION CODE
CODE
POSSIBLE CAUSES
WHAT TO DO
• Door is unlocked when washer is
running.
• Press the Power button to turn off your washer, then
restart the cycle. If the code reappears, call for service.
• Door is open when washer is running.
• Close the door tightly and restart the cycle. If the code
reappears, call for service.
• Your washer has tried to fill but was
unsuccessful due to clogged water lines
or closed watervalves.
• Make sure hot and cold water valves are open all the
way. Check for kinked hoses.
• Check the inlet screens on the fill hoses.
• Your washer is not draining.
• It can also mean that the unit senses a
small clog or frozen hose.
• Fill the washer drum with 10 ℓ of water at the
temperature of 140 ˚F for about 1 hour to defrost the
ice.
• Unbalanced load prevented your washer
from spinning.
• Redistribute the load, press the Start/Pause button.
• When the weight of the laundry is about
• Add more laundry.
1 kg, the center of the weight gets
shifted.
• To many suds are detected during the
washing session.
• The unit is put on hold until the suds are
reduced. Then, the unit will go back to
the operation. When it finishes washing,
“End” and “SUdS” code will blink in turn.
• Your washer is designed to use High Efficiency (HE)
detergents. For best cleaning results only use High
Efficiency detergents such as Tide HE, Wisk HE, CHeer
HE, or Gain HE. High Efficiency detergent contain
suds suppressors that reduce or eliminatesuds. When
fewer suds are produced, the wash load tumblesmore
efficiently and cleaning is maximized.
Code No. : DC68-02497A-02_EN
SWM-user_QG_3rd.indd 1
2008-01-09 ¿ÀÀü 12:33:15
operating detergent instructions
DETERGENT USE
Detergent
Compartment
• Our washer is designed to use High Efficiency (HE) detergents. For best cleaning results
only use High Efficiency detergents such as Tide HE, Wisk HE, CHeer HE, or Gain HE.
High Efficiency detergents contain suds suppressors that reduce or eliminate suds.
• The dispenser automatically releases at the proper time.
• Use the softener compartment ONLY for fabric softeners.
• Do NOT use the thick liquid fabric softener. It will not add fabric softener at the appropriate
time.
• Never pour undiluted liquid chlorine bleach directly onto clothes or wash load into the tub.
• Do NOT exceed the MAX FILL line.
Detergent Selector
Prewash
(Select Models)
MAX FILL line
how to install
REMOVING THE SHIPPING BOLTS
Before using your washer, you must remove shipping bolts. If not, it causes excessive
vibration.
1. Using wrench remove all Four (4) shipping bolts.
2. Install cap supplied from accessories.
4 Shipping Bolts
HOW TO LEVEL
1
Locking nut
2
Leveling leg ASSY
1
3
Wrench/Spanner
2
4
Flat head screw driver
3
Your washer MUST be leveled on all four sides.
• The installation surface must be firm, dry and level.
• A carpenter’s level should be used on all four corners of
your washer.
• The unit should not wobble when it is pushed & pressed
in all directions.
Avoid the damage of legs, do
NOT move the washer unless
the locking-nuts are fastened to
the bottom of the washer.
SWM-user_QG_3rd.indd 2
4
1. Level your washer by
turning the leveling legs.
2. When your washer is level,
tighten the nuts using the
wrench or (-) to flat head
screw driver.
2008-01-09 ¿ÀÀü 12:33:16