LG LP-P4020AA Owner's manual

Package
Air
Conditioner
OWNER'S
MANUAL
Before
manual
using your air conditioner please read this
carefully and keep it for future reference.
MODEL: LP-K2060HL/HA/ZL/ZA
LP-K3060HL/HA/ZL/ZA
LP-K3020HL/HA/ZL/ZA
LP-K4020HL/HA/ZL/ZA
Prior to
installation, this air-conditioning unit
must be submitted for
service which
Norm).
approval by the utility
provides electricity (EN 60555-3
Safety precautions
Safety Precautions
SafetyPrcuions
To
................................2
Warning
prevent injury
following
Caution .................................3
operation
the seriousness is classified
Specifications ....4
due to
and
property damage, the
ignoring
of instruction will
cause
by the following
harm
or
indications.
WARNING
WARNING
Indoor Unit Controls and
This
Indicators ..............................5
symbol
indicates the
possibility
of death
or
serious
possibility
of
or
damage
injury.
Name and Function-Remote
CAUTION
CAUTION
Control...................................6
Air conditioner
operation.......8
This
symbol indicates
properties only.
Care and Maintenance
Operation Tips
the
Installation
....................19
injury
to
precautions
WARNING
WARNING
Do not
install, remove and re-install the unit by yourself.
Improper installation will cause water leakage, electrical shock, or
fire. Please consult authorized dealer or specialist for the installation
Troubleshooting tips
Before You
Call For Service ...............20
work.
CAUTION
CAUTION
The
the
OPERATING
of the air conditioner is based
cycle system
air cooling type heat
reverse
Therefore if the outdoor unit is
exposed
INDOOR
to very low
off
OUTDOOR
MAX.
MIN.
MAX.
MIN.
32°C
21°C
43°C
21°C
HEATING MODE
INDOOR
OUTDOOR
MAX.
MIN.
MAX.
MIN.
temperature, specifically below 0°C, the heating capacity
drops
TEMPERATURE(°C)
COOLING MODE
pump which absorbs heated
air from the outdoor unit and discharges it indoor.
on
rapidly.
27°C
20°C
24°C
1°C
WARNING
WARNING
Do not
damage
or use an
Do not
unspecified
operate with
wet hand.
power cord.
?
It will
cause
electrical shock
Do not insert
or
fire.
anything into the
?
air inlet/air
Since the fan rotates at
cause an
When
cause
electrical shock.
Do not expose the skin directly to cool air
long periods of time.
an
injury
or
high speed,
damage the unit.
abnormality (smell
of
this may
If the unit continues to
condition, it may
cause
This could
?
burning, etc)
Repair
occurs, stop the air conditioner, and
disconnect the power plug or turn off the
circuit breaker.
?
It will
for
outlet.
?
Troubleshtingp
people
Incorrect
Care and Maintenance .......19
OperatingIsuco
CarendMitc
other
user or
damage,
Operating Instructions
Features and
to the
instructions must be followed.
or
damage
your health.
relocation should not be done
by
the customer.
operate in an abnormal
fire, damage, etc. In
?
If this is done
electric
this case, consult your dealer.
water
2
incorrectly, it may cause a fire,
shock, injury by dropping of the unit,
leakage,
etc. Consult your dealer.
CAUTION
?
Contact the authorized Service technician for
?
Contact the installer for installation of this unit.
?
The air conditioner is not intended for
?
The
?
?
repair or maintenance of this
unit.
use by young children or infirm persons without supervision.
appliance is not intended for use by young children or infirm persons without supervision.
Young children should be supervised to ensure that they do not play with the appliance.
If the supply flexible cord is damaged, it must be replaced by the manufacturer or the manufacturer's
service agent or similary qualified person in order to avoid hazard.
CAUTION
CAUTION
When the air filter is to be
Do not clean the air
Ventilate well when used
removed, do not touch the
metal parts of the indoor unit.
conditioner with water.
together with
?
?
It may cause an injury.
Should be disconnected from
?
supply
When the unit is to be
cleaned, switch off,
Do not
and turn
It may
cause an
electric
Do not
a
pet
or
?
exposed
Do not leave
an
on
stand which is
shock,
?
This could
injure
the
pet
or
?
plant.
apply
shortage
may
occur.
house
be
An oxygen
installation
damaged.
to direct air flow.
burning.
or
put
plant where it will
off the circuit breaker.
?
Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
stove, etc.
a
Do not
insecticide
flammable spray.
is
put
exposed
a
stove, etc. where
The unit may drop or fall down
and cause an injury.
Do not
to direct air flow.
not
?Itmaycauseafireor
?
It may affect combustion.
step
on
the
indoor/outdoor unit and do
?
deformation of the cabinet.
put anything
It may
on
it.
injury through
falling down.
cause an
dropping
or
Do not insert your finger or
stick etc. into the air inlet
When the unit is not
Do not open the air inlet
be used for
during operation.
grille.
off the circuit breaker.
?
It will
shock
Do not
?
use
Do not
for
?
If not, dirt may collect and
fire.
deterioration of
quality,
?
It may
shock
grille
cause an injury, electric
by the high voltage.
Do not operate for a long time in high
humidity, e.g. leaving a door or window open.
special purposes.
this air conditioner to preserve
devices, food, animal, plants, and art
cause
going to
long time, turn
cause a
use
precision
objects.
It may
electric
injury,
by the high voltage.
cause an
a
?
In the
with
etc.
3
cooling mode, if it is operated in a room
high humidity (80%RH or more) for a long
time,
water condensed in the air conditioner may
drop
and may wet and
spoil furniture,
etc.
SafetyPrcuionsOpgICdMTblh
Features and
SafetyPrcuions
OperatingIsuco
CarendMitc
Troubleshtingp
Specifications
Features
8
Anti-Bacteria filter
Super energy efficiency
9
3 minutes
3
Micom control
10 Jet Cool operation
4
Whisper quiet operation
11
5
Wireless remote control
12 Auto restart
6
2
13
7
Removable air filter
1
Design
2
for
cooling
cooling speeds
delay
circuit
Energy saving
Plasma Air
Purifying system
(HA/ZA MODEL)
Specifications
Air Outlet Vent
Remote
Signal
Receptor
Air Intake Vent
(Rear)
Air Intake Vent
Air Outlet
Vent
4
Indoor Unit Controls and Indicators
The remote control transmits the
signals
to the
system.
Features of the Remote Control- Door Closed
8
9
10
15
16
14
18
HA/ZA MODEL
A/CL
R00M
TEMP.
SET
TEMP.
19
20
JET COOL
On/Off
Mode
Fan
Temp.
Speed
Fan
Energy
Saving
Jet Cool
HA/ZA MODEL
Air
Cleaning
A/CL
123
1
2
4
12
5
13
6
8
COOLING OPERATION LAMP
Operation starts when this button is
pressed and stops when the button is
pressed again.
9
HEATING OPERATION LAMP
10
SOFT DRY OPERATION LAMP
11
JET COOL OPERATION LAMP
12
ENERGY SAVING OPERATION LAMP
13
OFF TIMER OPERATION LAMP
14
FAN OPERATION LAMP
OPERATION MODE SELECTION
BUTTON
operation
Mode.
INDOOR FAN SPEED SELECTION
Used to select fan
speed
in two
steps-low,
high.
JET COOL BUTTON
4
Used to start
15
stop the speed
cooling.(Speed cooling operates super
high
5
fan
or
speed
in
cooling mode)
16
ENERGY SAVING BUTTON
17
ROOM TEMPERATURE SETTING
6
18
BUTTONS
Used to select the
room
Used to circulate
room
AUTO AIRFLOW OPERATION
LAMP(VERTICAL)
OUTDOOR UNIT OPERATION LAMP
PLASMA AIR PURIFYING
BUTTON(HA/ZA MODLE)
AIR CLEANER OPERATION
LAMP(HA/ZA MODEL)
temperature.
19
FAN OPERATION BUTTON
7
17
7
START/STOP BUTTON
Used to select the
3
11
air without
ELECTRIC HEATER OPERATION
LAMP(OPTION)
cooling.
20
5
DEFROST OPERATION LAMP
SafetyPrcuionsOpgICdMTblh
Name and Function-Remote Control
SafetyPrcuions
Control
1
Signal Transmitter
Transmits the signals
?
1
2
3
Operation Display
?
2
air
of the Remote Control
Each time the button is
pressed, the
following process.
(1, 2, 3, 4, 5, 6, 7 hours)
mode is
in the
Timer set
8
If you select "0:00" the off Timer function will
be canceled.
A/CL
Troubleshtingp
package
Timer Set Button
changed
14
OperatingIsuco
CarendMitc
to the
conditioner
9
345
4
10
5
6
Plasma Air
Fan
Purifying Button(HA, ZA MODEL)
Operation Button(HL, ZL MODEL)
Auto Airflow Direction Control Button
?
The vertical louvers
swing
left and
right.
11
6
12
7
7
Jet Cool
Operation Button
Indoor Fan
?
13
Speed Selection Button
speed in two steps
[Low, High]
To select the desired fan
ON Button
8
Cooling
9
Heating Button
10
Soft
Dry Operation Button
Button
11 Energy Saving Operation
12
Power ON/OFF Button
?
Operation will start when this button is
pressed, and stop when the button is pressed
again.
13
Temperature Setting Buttons
14
Electric Heater ON/OFF
Wireless Remote Control Puts all functions at your
Handling
?
?
?
?
?
Button(Option)
fingertips
the remote control
Aim at the
signal receptor on the package air conditioner when operating.
The remote control signal can be received at a distance of up to about 7meters.
Be sure that there are no obstructions between the remote control and the signal receptor.
Do not drop or throw the remote control.
Do not place the remote control in a location exposed to direct sunlight, or next to a heating unit,
other heat
source.
6
or
Remote Control
Preparation
How to mount onto
1
Use the
to
screws
secure
a
wall
the holder to the wall
or
attach the holder side of indoor
unit.
2
To insert the remote control to the holder.
Insert
Pull
How to insert batteries
Remove the
cover
?
from the
?
Slide the
the
cover
according
use
rechargeable
different from standard
as
to
dry
direction.
arrow
Do not
batteries such batteries
back of the remote controller.
cells in
shape,
dimensions, and
performance.
Insert two batteries.
?
Be
sure
that the
directions
?
Be
sure
are
(+)
and
(-)
?
correct.
Change
properly
Re-attach the
Slide the
if the remote
control does not work
are new.
?
the batteries with
a new one
that both batteries
cover
after
extended
cover.
into back
position.
7
using for an
length of time.
SafetyPrcuionsOpgICdMTblh
Air conditioner
SafetyPrcuions
How to
1
?
Each time the
shifted in the
Mode
OperatingIsuco
CarendMitc
Troubleshtingp
the
use
Operation
arrow
operation
Mode Button
Operation
Mode Selection Button is
pressed,
the
Operation
Fan
Speed
Soft
SET
SET
TEMP.
TEMP.
Dry Operation
Heating Operation
SET
TEMP.
SET
TEMP.
Cooling Operation
2
How to
?
use
Each time the Fan
Mode
Mode is
direction.
the Fan
speed
Heating+Heater Operation
speed Button
Button is
pressed,
the Fan
speed
is shifted in the
arrow
direction.
Fan
Speed
High
8
Low
Cooling Operation
3
Press the
1
Start/Stop
Mode
Button.
On/Off
Select
2
Cooling Operation.Press the Operation
Operation Button on the remote controller.
Mode Selection Button. Press the
Cooling
Fan
Mode
Speed
A/CL
SET
TEMP.
Set the
3
The
temperature lower than the room temperature.
temperature can be set within a range of 16°C~30°Cby 1°C.
Temp.
Fan
To raise the
To lower the
4
When you finish the
temperature
SET
TEMP.
temperature
temperature setting.
After 4 seconds
SET
TEMP.
Set the Fan
5
Mode
R00M
TEMP.
Speed.
Fan
Speed
High
Each time the Fan
Speed
9
Low
Speed
Button is
mode is shifted in the
arrow
pressed,
direction.
the Fan
SafetyPrcuionsOpgICdMTblh
SafetyPrcuions
OperatingIsuco
CarendMitc
Soft
4
1
Dry Operation
Press the
Start/Stop
Button.
On/Off
2
Select Soft
Press the
Press the
Mode
Dry Operation.
Operation Mode Selection Button.
Soft Dry Operation Button on the
remote controller.
Fan
Speed
A/CL
SET
TEMP.
3
Set the
The
temperature lower than the room temperature.
temperature can be set within a range of 16°C~30°Cby 1°C.
Temp.
Fan
To raise the
To lower the
SET
TEMP.
temperature
temperature
During softy Dry Operation
Troubleshtingp
?
The indoor fan
Mode
speed
is
automatically
Fan
Speed
10
set to low and
can
be set fan
speed.
5
Jet Cool
1
Press the
Operation
Start/Stop
Button.
On/Off
Press the Jet Cool button to
2
super
high
fan
speed
on
operate the speed cooling mode and the unit will operate in
cooling
mode.
Energy
Saving
Jet Cool
SET
TEMP.
JET COOL
To cancel the Jet Cool
3
room
or
mode, press the Jet Cool button again or the fan speed button or the
temperature setting button and the unit will operate in high fan speed on cooling mode.
or
NOTE:
During the JET COOL function at any moment, the A/C starts
extremely high speed setting the room temp. automatically to
cool the
to blow the cool air at
18°C. It is
especially
used to
temp. in the shortest time in a hot summer.
In heat pump mode or neuro fuzzy mode however, the JET COOL function is not available.
In order to return to the normal cooling mode from the JET COOL mode, you just press
either the operation mode selection button, airflow volume selection or temp. setting button
or
room
the JET COOL button
again.
11
SafetyPrcuionsOpgICdMTblh
SafetyPrcuions
OperatingIsuco
CarendMitc
Heating Operation
6
1
Press the
Start/Stop
Button.
On/Off
Select
2
heating Operation.
Operation Mode Selection Button.
the Heating Operation Button on the remote
Press the
Press
Mode
controller.
Fan
Speed
A/CL
SET
TEMP.
Set the
3
The
temperature lower than the room temperature.
temperature can be set within a range of 16°C~30°Cby 1°C.
Temp.
Fan
To raise the
To lower the
Set the Fan
Troubleshtingp
Mode
Mode
SET
temperature
TEMP.
temperature
Speed.
Fan
Speed
*
Each time the Button is
Speed
12
mode is shifted.
pressed,
the Fan
Electric Heater
7
1
Press the
Start/Stop
Operation Mode(Option)
Button.
On/Off
2
Select
heating + E/heater Operation.
Operation Mode Selection Button.
Press the Heating Operation Button on the remote controller.(When the
Press the
Mode
unit
operates in heating mode.)
Fan
Speed
A/CL
SET
TEMP.
Set the
3
The
temperature lower than the room temperature.
temperature can be set within a range of 16°C~30°Cby 1°C.
Temp.
Fan
Set the Fan
Mode
To raise the
temperature
To lower the
temperature
SET
TEMP.
Speed.
Fan
Speed
*
Each time the Button is
Speed
13
mode is shifted.
pressed,
the Fan
SafetyPrcuionsOpgICdMTblh
SafetyPrcuions
OperatingIsuco
CarendMitc
Troubleshtingp
Energy Saving Mode(Cooling Operation Only)
8
1
Press the
Start/Stop
Button.
On/Off
2
Select
You
Energy Saving
can
Jet Cool
mode.
select this function
during
the
operation
of
Cooling/Auto/Soft Dry.
Energy
Saving
SET
TEMP.
To cancel the
3
operate
Jet Cool
on
Energy Saving mode, press
Cooling/Auto/Soft Dry mode.
the
Energy Saving
button
again
and the unit will
Energy
Saving
SET
TEMP.
Auto restart
In
case
the power
function to
In
off
case
comes on
again
after
a
power failure, Auto Restarting Operation is the
to the previous operating conditions.
operate procedures automatically
the air conditioner does not receive any
after 7 hours.
automatically
14
signal
from the remote
control, it will
turn
Fan
9
Operation
Press the
1
Mode
Start/Stop
(HL/ZL MODEL)
2
Button.
On/Off
Press Fan
Operation
Button.
Fan
SET
TEMP.
Set the Fan
3
Mode
Speed.
Fan
Speed
Low
High
Each time the Fan
Fan
Speed
Button is
Speed
mode is shifted in the
2
louvers will
pressed,
arrow
the
direction.
Airflow Direction Procedure
10
Press the
1
Start/Stop
Press the Auto
Button.
Swing Button and
swing left and right.
Press the Airflow Direction
Control Button
On/Off
and
again
to set
the Vertical louver at the
A/CL
(Operation
then
will start when the button is
desired airflow direction.
pressed,
stop when the button is pressed again.)
The vertical louver
swing
left and
right.
Note
Always
use
the remote control to
direction louver
by
hand could
adjust the right/left airflow direction, manually moving
change the air conditioner.
the vertical airflow
Vertical Airflow Direction Control
Adjust the
vertical airflow direction
manually by moving
the horizontal louvers with hand.
15
SafetyPrcuionsOpgICdMTblh
SafetyPrcuions
11
Plasma Air Purifying
Air
1
Procedure
(HA/ZA MODEL)
Purifying Operation only
Press the Plasma Air
1
Operation
Purifying Operation Start/Stop
Button.
Air
Temp.
Cleaning
A/CL
A/CL
OperatingIsuco
CarendMitc
Troubleshtingp
(Operation
will start when the button is
Select Fan
2
The
and
stop when the button is pressed again.)
speed.
display
Mode
pressed,
shows low fan
speed
at the initial condition.
Fan
Speed
A/CL
A/CL
SET
SET
TEMP.
TEMP.
Low
High
?
You
dry
2
can
or
Air
operate the Plasma Air Purifying under the unit operation of cooling, heating, soft
Auto mode.
Purifying Operation
1. Press the
Start/Stop
2. Select the desired
Cooling
or
any other
Operateion.
Button.
Operation
3. Press the Plasma Air
4. Set the fan
with
Mode.
Purifying Operation
speed.
16
ON/OFF Button.
12
OFF Timer Setting
1
Press the
Start/Stop
Procedure(OFF TIMER Setting,
or
CANCEL)
Button.
On/Off
Press the Timer Button.
2
A/CL
If you press the
?
?
3
If you select
'
button, the selected off timer is displayed
as
', the Off Timer function will be cancelled.
When you finish the Off Timer
setting,
the Timer indicator
After 4
seconds
lights
During off-timer operation
displayed.
off.
After 4
seconds
SET
TEMP.
4
follows;
if you press the Timer
17
R00M
TEMP.
Button, the
rest time will be
SafetyPrcuionsOpgICdMTblh
SafetyPrcuions
OperatingIsuco
CarendMitc
Troubleshtingp
Child Lock
13
1
Operation
Procedure
Press the low and
high temperature setting
respond with beep.
The unit will
Temp.
buttons
simultaneously
Fan
R00M
TEMP.
SET
TEMP.
After 3 seconds,
it will shifted.
2
During
for 3 seconds.
Child Lock
After 3 seconds,
it will shifted.
Operation
Whenever you press any Button on Display Panel, it will
", which means Display panel is Locked.
immediately display
"
All the Button
on
But the Button
3
For
releasing
Temp.
Fan
on
the indoor unit
Display panel
will not work.
the remote controller will work.
child lock
Operation.
Press the low and
high temperature setting buttons simultaneously
again.
rospond with beep, Child Lock Operation will removed.
for 3 seconds
The unit will
R00M
TEMP.
SET
TEMP.
After pressing
the buttons
it will shifted immediately
After 3 seconds,
it will shifted.
18
Care and Maintenance
CAUTION: Before performing any
During
the
maintenance,
turn off the main power to the
season
Cleaning of the air cleaner.
Recommended about once every three months
Cleaning of the air filters.
Recommended about once every two weeks
Remove the Air Filter.
Take hold of the tab and
remove the filter.
Clean.
To remove the dust
?
vacunm
?
cleaner,
or
pull slightly forward
Don't wash with water.
Wipe
soft
?
filters, either use a
dry
in the
dry
pull slightly forward to
?
Dip the air cleaner into the water mixed with
detergent, for 20~30minutes, and dry in the shade.
Re-insert the air cleaner to the original position.
original position.
of the air conditioner
?
a
to the
wash them in water and
?
with
Remove the Air Cleaner.
Take hold of the tab and
remove the air cleaner.
to
Clean.
adhering
shade.
Re-insert the filter to the
Cleaning
system.
Never
?
Could
cloth.
use
any of the
Water hotter than 40°C.
cause
?
deformation
followings.
Volatile substances.
Could
and/or discoloration.
damage the surfaces
of the air conditioner.
When the air conditioner is not going to be used for a long time.
At the end of the
At the start of the
season
Operate the air conditioner at the following
settings for 2 to 3 hours.
Type of operation : Cooling.
Temperature setting : 30°C.
This will dry out the internal mechanisms.
Clean the air
season
filters, re-insert, then operate
the air conditioner.
?
?
Remove the batteries from the Remote Control.
Be
sure
that
nothing
obstructs the air outlet
and intake vents.
Turn off the circuit breaker.
CAUTION
CAUTION
Turn off the circuit breaker when the air conditioner
is not going to be used for a long time.
Dirt may collect and may cause a fire.
Operation Tips
Do not overcool the
This is not
wastes
Make
good for
electricity.
sure
windows
Avoid
much
the
room.
your health and
shut
or
curtains closed.
when the air conditioner is in
Keep the
room
temperature uniform.
Adjust the vertical and
direction to
ensure a
operation.
temperature in the
Clean the air filter
Ventilate the
tight.
opening doors and windows as
as possible to keep the cool air in
room.
blinds
Do not let direct sunshine enter the
room
that the doors and
are
Keep
Blockages
airflow and lower
dehumidifying
once
regularly.
in the air filter reduce the
cooling
and
effects. Clean at least
every two weeks.
19
room.
room
Since windows
are
horizontal airflow
uniform
occasionally.
kept closed,
it is
a
idea to open them and ventilate
the room now and then.
good
SafetyPrcuionsOpgICdMTblh
Before you call for service...
SafetyPrcuions
Troubleshooting Tips! Save
?
Check the
following points
contact your dealer
before
Does not
or
service.... If the fault
operate.
persists, please
See page
Explanation
?
Have you made
?
Has the fuse blown
a
mistake in timer
operation?
has the circuit breaker been
or
tripped?
?
?
The
room
has
a
?
peculiar
seems
leaking
that condensation is
?
Check that this is not
Condensation
occurs
conditioner cools the
from the air
-
Heating Operation?
If yes, Hot-start is activating.
Is the unit in the Deicing?
If yes, wait for finishing the Deicing.
a
walls, carpet, furniture,
odor.
It
Is the power Switch at Off?
Is the unit at the starting of
smell exuded
damp
or
cloth items in the
by
the
-
room.
when the airflow from the air
warm room
air.
-
conditioner.
Air conditioner does not
?
This is the Protection device of the air conditioner
operate for about
?
Wait about three minutes and
operation
If the airflow
temperature become
3 minutes
?
when restarted.
warm, it will
order to
it is
Does not cool
or
heat
?
begins
before its
cause an
undesired
cooling
prevent this, the airflow will
not
will
.
begin.
effect. In
begin
until
sufficiently warm.
Is the air filter
dirty?
See air filter
cleaning
19
instructions.
effectively.
?
The
room may have been very hot when the room
air conditioner was first turned on. Allow time for it
-
to cool down.
?
Has the
?
Are the indoor unit's air inlet
temperature been
set
or
incorrectly?
outlet vents
-
obstructed?
The air conditioner
is
operation
?
For
a
noise that sounds like water
-This is the sound of freon
noisy.
flowing
flowing.
inside the air
conditioner unit.
?
For
a
noise that sounds like the
compressed
air
-
into
atmosphere.
dehumidifying water being
processed inside the air conditioning unit.
releasing
Troubleshtingp
requesting repairs
service center.
Case
?
OperatingIsuco
CarendMitc
or
time and money!
-This is the sound of the
Remote controller
faint,
or no
display
display
at all.
is
?
Are the batteries
?
Are the batteries inserted in the
depleted?
opposite (+)
and
(-)
7
directions?
NOTE
WATER RESISTANT: The outdoor side of this
appliance
is WATER RESISTANT.
The indoor side is not water resistant and should not be
20
exposed
to
excess
water.
P/No.: 3828A30063A
Printed in Korea