advertisement
▼
Scroll to page 2
of 22
WD WD WD WD WD WD 6011 6012 8011 8012 1011 1012 C C C C C C - - - - - - WD WD WD WD WD WD 6011 6012 8011 8012 1011 1012 CH CH CH CH CH CH This product has been manufactured at environmental friendly modern facilities. Dear Customer, We wish that this you the best and keep product, performance. manufactured at modern facilities with total In order to guarantee quality notions, will deliver this, please read this instruction manual thoroughly it for your future reference. www.lge.co.kr CONTENTS Part 1: Part 4: Steps before operating Fullautomatic Washing Machine and safety precautions. Program Part 2: Care and Maintanence. selection and washing operations. Part 5: Technical features. Part 6: Helpful tips stain removal on Part 3: Determining location and installation Part 7: Before 1 calling service. Part Steps before operating Fullautomatic Washing Machine and safety precautions 1: The current requirement in order for safe operation of this machine is 16 electrician to connect a 16 Amp fuse, if there is not enough current load. Ampheres. You will need to have a certified Your washing machine is set to 220-230 Volts. Do not forget to check the for any damages In order to bring caused grounding in all cases of use with or without the by operations without grounding. the machine to ready before use, transformer. Our company will not be please call your service technician or a certified responsible plummer. performance of the washing machine depends on the effectiveness of the cleaning agent. Stains can be permanent if quality detergents are used. Please take necessary effort to clean the stained clothes as described in following pages before washing them in the machine. The low To open the front door Make sure the Power switch is in the off position and for the door safety always allow one to two minutes lock to release the lock. Pull the handle to open the door. Due to the quality control processes during production, there may be some water left over in your machine. This does not cause any damage to your product. 2 Part 2: Control Top features Technical panel lid Detergent dispenser Front door WD 1012C WD 6011CH WD 6012CH WD 8011CH WD 8012CH WD 1011CH WD 1012CH 85 cm. Width 60 cm. 60 cm. Depth 54 cm. 45 cm. Net 60 kg. 57 kg. weight requirement 4.5 kg. (11.1 lbs) 220-230 V, 10 A. 300 Watts. Heater power 1900 Watts. 50 rpm. Spin speed WD 8011C WD 8012C WD 1011C WD 1012C - - - - - - WD 6011CH WD 6012CH WD 8011CH WD 8012CH WD 1011CH WD 1012CH ) ) ) kg. (10 lbs) 50 Hz. Motor power ( ( ( 3 1011C cm. WD 6011C WD 6012C screw 8012C WD 85 Max. opening 6012C WD Height Washing speed Kick plate WD 8011C 5 Nominal current Kick plate 6011C WD Capacity (dry fabric) Power Handle WD 600 rpm. 800 rpm. 1000 rpm. Part 3: 1. Removing transport safety Determining bolts at the rear location and installation of the machine C C P C C C The transport safety bolts must be removed before any operation of "C", should be turned in the machine. Bolt heads, marked until the bolt can be "C". a anti clockwise direction partially withdrawn. Remove transport safety bolts and rubber bushes by pulling outwards. (A up/down action and a small squirt of washing up liquid should ease removal.) Plastic plugs, supplied inside bag and designated as "P", should be placed in the safety bolt holes according to the the protective direction shown. Attention! Please keep the safety bolts for future transportationand reinstate them before Never transport your machine without the transport bolts in Never transporting your machine. position. place your machine on a carpet. This prevents air circulation. The electrical components of the machine may overheat and may cause damage. 4 2. Feet adjustment In order for quiet and stable operation, the machine should be placed properly and leveled on is its feet. Your machine unstable, loosen the plastic until the machine is leveled comes with two counternut and perfectly. After adjustable screw or unscrew feet. If the machine the positioning, tighten the foot adjustable counternut for stability. 3. Water connections a) Water inlet hose Cold water supply For proper operation, the pressure of water should be between 1 and 10 atm. (1 atm more than 8 liters per minute flow rate at fully open tap.) corresponds To prevent water leaks sealing washers are supplied with the water inlet hose inside the these on each of the hose ends and tighten both ends fully. In order to prevent any water leak damages, keep the water taps closed when not in cornered end of the hose to the machine water inlet. Hot water supply (only for hot and cold water inlet Pressure: 1-10 bar Temperature: 60°C normally be suitable. Open outlet gas max. or A hot water are designed to machine, place use. HOT COLD Connect the machines) supply fed from a separate cold water tank will electric water heaters must not be used. combination boilers may be suitable if they boilers operation instructions or supplier.) or to supply washing Connect the cold water using the hose with blue printing and 5 Multipoint water heaters machines. (Check your connect the hot water using the hose with red printing. b) 4. Electrical connection Water drain hose Water drain hose could be placed either at the side of the bath tub, or directly to the drain. The hose should not be bent. Water drain hose should be secured with the elbow so that it would not fall down on the Connect the power cord to the appropirate electrical system which is being supported by the maximum voltage and current rating indicated plate placed inside the kick plate. ground. The hose should be 100 cm. from the placed between 60 and placed to the drain water inlet. Attention! Before any rating Page 1, Steps before operating Washing Machine and safety precautions. Fullautomatic Water drain hose directly the Look! ground. could be on 0123456789 Make have sure grounded outlet. operation of the machine check the following. Did you close the front door? Is water drain hose Is the tap Is power connected? open? 6 that you placed properly? power Control Panel Program selection WD 1011C WD 1012C - - WD 1011CH WD 1012CH Wash selection Temperature Start/ selection Pause Rinse selection Option selection Power Detergent drawer : ( Spin speed selection for : ( WD 6011C WD 6012C Spin speed selection for WD 8011C WD 8012C - - - - WD 6011CH WD 6012CH ) WD 8011CH WD 8012CH ) 7 Spin speed selection Preparation Loading the machine Place the fabrics no clothing uniformly inside the machine. Hand knits should be at the side of the door. Close the door by pushing lightly. placed inside not be started-a Front door is locked untill the end of the minutes program. safety measure. following the end of the out in the machine. Make If the door does not close washing completely, sure that there is the machine could program and it will not be opened about 2 Sorting laundry Sort the - - - - laundry according to the following groups and wash them seperately: white and resistant colored fabrics, colored fabrics, delicate fabrics (silk, rayon etc.), wool. Be sure to empty pockets and information" section of the Detergent remove any operating belts, buttons, pins, etc. from the clothing. For stained fabrics, refer to the "Practical manual. and softener selection Choose the appropirate detergent specifically used at the full automatic washing machines Suggested amount is given on the detergent cover. If small amount of clothing is placed in the machine and half load option is selected, put half the amount of detergent required Do not attempt to on for normal wash. use detergents and bleaching elements that contain chlor and the dirt level of fabric, the amount of fabric and the softness of the water. 8 sulphur. The amount of the detergent depends Program selection Program for white cloths Program for coloured cloths Designed for synthetic fabrics, naylon clothing, curtains and fabrics. Clothing are washed with more water delicately. Shortens iron free wool washing time for lightly soiled fabrics. This function can be synthetic programs for temperatures below 60ºC. used for cotton and This program is used for laundry that has to be washed delicately like washable artificial silk, trousers, blouses, tullecurtains, child/baby drainage and wear. With wool program selection wool fabrics Used for more slowly nylon socks, of the water inside the are washed washing throughly. machine. Cloths will be washed at lower temperatures and longer time. This enables an economic and better wash results. Only available at 60˚C and 90˚C temperatures. this function your machine will add another rinse process to the three rinse processes that it has already done. This additional rinse will reduce any affects on sensitive skin by washing leftover detergent. By using The most economic wash is obtained by selecting half load button if half the amount determined in the program selection table is placed in the machine. ? Option selection When half load button is used. ? 9 selected, half of the amount of detergent should be Detergent dispenser Temp. Selection Using this button, you can select final up to 90˚C in whites, temperature up to 60˚C in coloureds, synthetics, wash, Rapid, up to 40˚C in Hand Wool programs. If you don't want to apply heating, you can select also cold wash. Compartment I. detergent compartment prewash cycle. b. Compartment II. detergent compartment for wash cycle. c." Compartment for fabric a. for Spin Selection WD 1011C WD 1012C " - WD 1011CH WD 1012CH Using this button, you can select final spin speed upto 1000 rpm in Whites, Coloureds, Rapid and Synthetics, up to conditioner. d. - Siphon. 800 rpm in Hand wash and Wool. Fill the fabric softener to the excess marking. Any amount of softener will mix into the WD 8011C wash water and you will have to re-fill the compartment. Hardened softener may clogg the siphon, in this case add WD 8012C - - WD 8011CH WD 8012CH Using this button, you speed upto 800 rpm. some water to the softener. If you don't want to WD 6011C apply spinning WD 6012C clothes, also No you to your can Spin. 10 select - - can select final spin WD 6011CH WD 6012CH Using this button, you can select final spin speed upto 600 rpm. Rinse Selection Using this button, you can select normal rinse, super rinse, normal rinse + rinse hold, super rinse + rinse hold. If you don't want to apply rinsing, you can select also no rinse, by pressing the rinse button till the leds turn off. Rinse Hold: If you desire to leave your synthetic and wool fabrics in the machine after the wash program you may select the Rinse hold to either press the Rinse button you discharge the water. can Super: prevent them getting wrinkled. To continue the program, again or select DRAIN The rinse water levels will be increased and an on the option selection button to extra rinse cycle is added. Normal: Normal rinse cycle is made. (3 rinsing steps) Wash Selection Using this button, you can select only main wash, main wash with prewash or no wash. If no wash is selected by pressing the wash button till the leds turn off, the program will start with the rinse cycle. Program selection table OPTIONS PROGRAMMES * Options ** You TEMP. (˚C) RINSE PREWASH HALF RINSE LOAD PLUS ** ECO DRAIN WD 6012C WD 8012C WD 1012C WD 6012CH WD 8012CH WD 1012CH LOAD LOAD kg. kg. FABRIC TYPE soiled cottons and linens 40-90 * * * * * * 5 4.5 Heavy Cold-60 * * * * * * 5 4.5 Normally soiled cottons and linens Cold-60 * * * * * * 2.5 2.5 Normally soiled Cold-40 * * * * 1.5 1.5 Lightly soiled synthetics Cold-40 * * * * 5 4.5 Lightly soiled Cold-40 * * * * 1.5 1.5 Woolens avaible can WD 6011C WD 8011C WD 1011C WD 6011CH WD 8011CH WD 1011CH select only one option during a program. synthetics and delicates and delicates cottons and linens Machine operation Place your clothes into the machine and close the front door. Determine the program after referring to the program selection table. Put powder detergent and the fabric softener to the compartments and close the detergent dispenser. Push the POWER button to turn on the washing machine. Program and option leds are turn on. Program Selection Pressing the Program button sequentially fallowing COLOUREDS Option SYNTHTETICS programs are turn on: HAND WASH RAPID WHITES Selection Pressing the Option button sequentially fallowing options DRAIN ECO RINSE PLUS are turn on: HALF LOAD 12 13 Child-Care Lock in order to During washing, pressed buttons, lock, press the washing there is a prevent child-care any lock, Temp. and Spin buttons interruptions during as a safety at the same process has been started. All the program and amounts of time. The child-care lock will lock all the When the program finishes, with an measure. keys by mistakenly To activate the child-care time (for three seconds) after the option active child-care the program leds begin to blink for certain and buttons included Power button. lock, the start/stop button will still blink. To open the front door at the end of the program or to interrupt the program during the process you have to deactivate the child-care lock. To deactivate the lock you have to press the Temp. and Spin buttons at the indicates that the child lock is time (for three seconds). The same active, will stop blinking leds, which blinking. Buzzer On/Off If Wash and Rinse buttons again pressed same the wash and rinse buttonns at the 14 time buzzer will be off. To turn same time. on the buzzer press Program operation The selected program can be started by pushing the Star t/Pause button. Front door will be locked and the led indicator will go on. To stop the machine during the program press the start/pause button again. If fabric softener is added in the softener compartment, it will be used in the last cycle. If rinse hold is selected, by re-pressing this button, you can continue rinse the program. If no spin is desired, you may leave the rinse hold button pushed. Pause the machine, select the Drain option and Start the machine. With this operation, water in the machine will be discharged. Program Following After the start of a program, the led of the if maih wash led is on, the machine is Auto Off / Unloading Machine stops automatically on ongoing program step led will turn on. the main wash step. If the 90 C led tuns The finished program step leds will turn off. As off, the heating an example is finished. the machine automatically after the programs are completed, and the buzzer beeps 7 times. After 8 seconds the machine will be can be opened 1-2 minutes after the end of the program. Turn off the water tap. Unload the machine turn off. Front door and leave the front door open to air the machine. 15 Part 5: Care and maintanence Detergent dispenser To clean the detergent residues, by pressing on the area marked the dispenser to its place. the detergent dispenser from its place siphon. Wash the dispenser with water and also clean the dispenser housing before inserting remove on Siphon Clean the siphon (coloured piece in the dispenser) every 30-40 washes. Pull out the siphon by holding from its edges. To prevent clogging, clean the softener residues thoroughly and make sure that the siphon fits into its place completely before any operation. 16 Hoses To prevent any leakage, have a technician to control the hoses every two years. If the machine is placed at cold ambient temperatures, the water remining inside the pump and hoses should be removed from the filters. Also to prevent freezing, empty the water intake hoses disconnecting from taps. by Water intake filter At the end of the water intake connection module and water inlet hose-tap side, there exists filters. These filters prevent any dirt and objects passing into the machine. It is advisable that these filters should be cleaned every 30-40 washes. To clean the filter, first turn the tap off. Then, disconnect the hose and clean the filter with a thin brush. If the filter is very dirty, you may clean it by pulling out with pliers. To clean the filter at the tap side of the hose, pull it out by hand and clean the filter under the tap water. Drum Do not leave any metal objects (pins, needles, etc.) inside the drum. These objects may cause rust on the drum surface. Do not clean the drum with scratching elements. 17 HOT COLD Cleaning the pump filter To prevent objects entering to the pump, your machine comes with a filter system that extends the pump life. It is advisable that you should clean the filter at every 30-40 washes. Before opening of kick plate opening the filter door, disconnect the screws 90° with a help of screw driver power. Turn the or a coin. Place little pan infront of the filter door to prevent a the machine. Remove the filter it counter-clockwise direction. After cleaning the it is closed objects firmly. on the filter, by turning place Place the kick Attention! it by little amount of water a spilling turning clockwise and make plate and secure it by locking If the filter does not fit into its place, will leak out from the filter. 18 the sure from that screws. water The following stain removing tips are approximate and can only washing information of the fabric manufacturer. be used at the washable fabrics. Please Ratios consult the Alcoholic Shoe the fabric first with water, then solution and rinse with vinegar-water solution. baverages: Wipe water-glycerine Without harming the fabric, remove the stain and grind it with detergent. If this doesn't help, prepare a water to alcohol solution (2 to 1) and rub the fabric, then wash it with warm water. polish: carefully are approximated. Blood stain: Leave the fabric for30 minutes in the cold water. Use ammonia solution to remove the stain. (4 liters water3 spoonful of ammonia.) Ice-cream, milk and cream: Place the fabric into cold water for period of time. Rub it with soap or detergent and wash it with the a warmest water that the fabric wipe can withold. If any grease stain leftover it with oxygen water. Tea and coffee: Pour hot water on to the stain and the fabric is white, pour some bleach and rinse it with water. Bubblegum: Harden the gum stain Then scrape off the stain carefully. by putting an ice on it. Chocolate and cocoa: Place the fabric into cold water for of time. Rub it with soap or detergent and wash it with the warmest water that the fabric can withold. If any grease stain leftover wipe it with oxygen water. a period Tomato paste: Scrape the hardened paste and leave the fabric for 40 minutes into cold water. Rub it with wash. Mildew: Do not let mildew stains stay for long periods of time. Place the fabric into cold water for a period of time. Rub it with soap or detergent and wash it with the warmest water that the fabric can withold. If any grease stain leftover wipe it with oxygen water. Fruit: Pour cold water on to the stain and do not use warm water to rinse. Let it sit for 2 hours and wipe it with white vinegar and rinse. Ink: Let the cold water run on the stain and wait until the stain is gone. Later rub it with lemon juice and for five minutes and rinse the fabric. detergent, let the stain stay detergent and Egg stain: If the stain is hardened scrape the stain and wipe it with wet sponge or a soft cloth. Rub it with detergent and wash with cold water. Grass stain: Rub the stain with detergent. If the fabric lets, bleachinng element. Wools should be Paint: Use thinner to remove wiped the stain. Put wool fabrics. Rub the stain with a use with alcohol. cotton cloth detergent and on the rinse with cold water. Grease stain: Scrape the stain and rub it with detergent. Then wash the fabric with warm water. Mustard: Use glycerin and rub the fabric with detergent. If unsuccesful, wipe the stain with alcohol. (Colored and synthetic fabrics need 2 cups water and 1 cup alcohol solution.) Burnt stains: Use bleach if permissable. For wool fabrics place oxygen water inserted cotton cloth on the stain and iron. Rinse completely and wash the fabric. a Before Part 7: You turned the machine on, but the leds on the panel. Check the grounding on the power cable Check the front door proper closure. or a are Check if the 8 or planced as the international textile Foam coming out of the detergent dispenser. Check whether your detergent is suitable for automatic machines. Next time use less detergent. are Pump does not drain water. Clean the pump filter. Check whether the drain hose is bent or not. If there is need to clean the pump filter, refer to the pump filter cleaning section of the manual. described in page care label from beneath the machine. (ITCL) symbols P Cl 60° Washing Bleach temperature be used dry cleaning hose coming Check the water intake and drain hoses. Tighten the connections. The washers of the hoses may be worn out. If non of the both, the pump filter is not closed properly. directly discharged. discharge service Water not. Descriptions of No off blown fuse. Machine does not take water. Check the front door for proper closure. Either taps closed or water intake filters are clogged. Taken water is calling No can spin Do not use Do not machine bleach wash Can be washed Do not wash at centrifugal centrifugal machine machine Dry on horizantal Do not wash surface Line dry 19 Dry clean A Chemicals be used Iron permitted Do not iron Warm iron can
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project