advertisement
▼
Scroll to page 2
of 44
DLP PROJECTION TV OWNER'S MANUAL Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached and quote this information to your dealer when you require service. Model number : Serial number : on the back cover FOR THE GUARANTEE TERMS & CONDITIONS, PLEASE REFER TO BACK COVER OF THIS MANUAL P/NO : 3828VA0531D (3840VA0016C) (MB05DA, 136G/100X TX) a Contents Installation 3 Location and function of controls Remote control handset Battery installation Front panel / Rear panel 4 Basic operation On and off / Programme selection Volume adjustment / Quick view Mute function / On screen language selection 8 (option) On screen menus Menu selection 9 STATION MENU Auto programme tuning Manual programme tuning Fine Tuning / Programme edit Favourite Programme Calling the programme table 10 PICTURE MENU 15 PSM(Picture Status Memory) (Excellent Digital) CSM (Color Starus Memory) Manual Colour Temperature Control (User option) sRGB (RGB[PC], HDMI[PC] mode only) ACM (Active Color Management) Manual Picture Control (User option) SOUND MENU SSM (Sound Status Memory) / BBE AVL (Auto Volume Leveler) / Balance adjustment Equalizer (option) / Sound output selection Stereo/Dual reception / NICAM reception 19 TIME MENU Clock / On/Off Timer Auto sleep / Sleep timer 23 SPECIAL MENU Child Lock / 25 Demo SCREEN MENU Auto Configuration (RGB [PC] mode Manual Configuration (RGB [PC]) Setting Picture Format / Cinema NR (Noise Reduction) Initializing (Reset only) original factory value) PIP/DW MENU Main Picture Source Selection 30 Picture in picture (PIP) function On and off / Input mode selection for sub picture Swapping between main and sub pictures Programme selection for sub picture Sub picture size / Sub picture position change Adjusting PIP Transparency (PIP mode only) 31 Teletext (option) Switch on/off / SIMPLE text TOP text (option) / FASTEXT Special teletext functions 33 Connection of PC PC in socket 36 Connection of external equipment Aerial socket / Euro scart sockets Audio/Video input sockets S-Video / Audio input sockets (option) DVD input sockets DTV input sockets / HDMI 37 Troubleshooting 2 to 26 check list 43 Installation Power This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set. In the event of thunderstorms or powercuts, please pull out the aerial and mains plugs. Warning To prevent fire moisture. shock or hazard, do not expose the set to rain Do not place anything containing liquid on top cause a fire or could give an electric shock. Wiring (in U.K. only) or of the set, this may This set is supplied with a BS 1363 approved 13 amp mains plug, fused at 5 amp. When replacing the fuse always use a 5 amp BS 1362, BSI or ASTA approved type. Never use this plug with the fuse cover omitted. To obtain a replacement fuse cover contact your dealer or "LG Electronics U.K. Ltd." If the type of plug supplied is not suitable for the mains sockets in your home, then the plug should be removed and a suitable type fitted. Please refer to the U.K. Warning (in instructions below: only) A mains plug removed destroyed. A mains plug a wiring from the mains lead of this set must be with bared wires is hazardous if inserted in mains socket. Do not connect either wire to the earth pin, marked with the letter E or with the earth symbol or coloured green or green and yellow. If any other plug is fitted, the distribution board. Important (in U.K. use a 5 amp fuse, either in the plug, or at only) The wires in this mains lead are coloured in accordance with the following codes: BLUE: NEUTRAL BROWN: LIVE As the colours of the wires in the mains lead of this set may not correspond with the coloured marking identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Service Never the back cover of the set as this can expose you to very high voltage and other hazards. If the set does not operate properly, unplug it and call your dealer. remove Aerial Connect the aerial cable to the socket marked +75 Ω on the back cover. For the best reception an outdoor aerial should be used. Location Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover. Avoid having a fixed image remaining on the screen for a long period of time. Typically a frozen still picture from a VCR or DVD, 4:3, 14:9 or 16:9 picture format or if a CH label is present the fixed image may remain visible on the screen. Disposal of your old appliance 1. When this crossed-out wheeled bin by the European is attached to a product it means the product is covered Directive 2002/96/EC. 2. All electrical and electronic 3. symbol disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. The correct disposal of your old appliance will help prevent potential negative consequences for products should be the environment and human health. 4. For more waste detailed information about disposal service or the shop disposal where of your old appliance, please you purchased the product. contact your city office, 3 Location and function of controls All the functions can be controlled with the remote control handset. Some functions can also be adjusted with the buttons on the front panel of the set. Remote control handset POWER Before you use the remote control teries. See the next page. 1 MULTIMEDIA 234 TV/AV MUTE 13 1. SLEEP PIP 2. 5 PR- PR+ 3. SWAP INPUT PR CANCEL/EXIT 7 15 4. 5. VOL OK VOL 8 on from standby MULTIMEDIA selects Component 1/2, RGB or off to standby. HDMI modes. or SLEEP sets the 6 MENU POWER switches the set TEXT handset, please install the bat- timer. sleep MUTE switches the sound on or off. PIP BUTTONS PIP switches the sub picture on or off. PR +/selects a programme for the sub picture. SWAP alternates between main and sub picture. INPUT selects the input mode for the sub picture. PR SIZE 123 adjusts Moves the sub 9 7 8 12 SIZE INDEX TIME MIX MODE I/II STILL REVEAL M / selects a 17 7. MENU selects a menu. ? 8. 14 REW PLAY D / E (Programme Up/Down) selects a programme or a menu item. switches the set on from standby. ARC P/STILL viewed programme. favorite programme. previously 16 LIST 18 STOP to D / E or F / G direction. picture SWAP returns to the SSM 0 10 POSITION size. 9 6. PSM picture POSITION 456 11 the sub F / G (Volume Down/Up) adjusts the volume. adjusts menu settings. REC 19 FF OK accepts your selection 9. or NUMBER BUTTONS switches the set on from 10. PSM (Picture Status recalls your preferred the current mode. displays standby or directly Memory) picture setting. 11. TELETEXT BUTTONS (option) These buttons are used for teletext. For further details, see the 'Teletext' section. 12. LIST (With TELETEXT) 4 displays the programme table. select a number. Location and function of controls 13. TV/AV selects the remote switches the set operating mode. on from standby. POWER 14. ARC (Aspect Ratio Control) changes the picture format. 1 MULTIMEDIA TV/AV 2 15. CANCEL/EXIT Clears all on-screen 13 LIST displays and returns to TV viewing 14 from any 12 menu. ARC MUTE PIP 5 4 PR- (Sound Status Memory) recalls your preferred sound setting. PR+ 16. SSM SWAP 6 MENU 17. STILL freezes motion of the INPUT PR CANCEL/EXIT 15 7 picture. 18. I/II VOL selects the language during dual selects the sound output. language broadcast. OK VOL 8 19. VCR BUTTONS control a video cassette recorder. PR Note : In teletext mode, the PR used for teletext function. + / -, SWAP and INPUT buttons are 123 456 Battery 9 installation The remote control handset is powered by two AAA type batteries. 7 8 9 PSM 0 SSM 16 To load the batteries, turn the remote control handset over and 10 open the battery compartment. Install two batteries as indicated by the polarity symbols ( + and - ) marked inside the compartment. POSITION SIZE STILL 17 SLEEP I/II 18 3 STOP REW P/STILL PLAY REC FF 19 Note : To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the remote control handset for an extended period of time. (Without TELETEXT) 5 Location and function of controls Front panel Lamp indicator, operation indicator, and temperature indicator, located side the reveal the operating status of the DLP(Digital Light Processing) projection TV. front panel controls ON/OFF TV/AV MENU TV/AV 1 MENU OK VOL PR VOL OK 234 PR 6 5 789 1. REMOTE CONTROL SENSOR 7. OPERATION INDICATOR (Refer 2. TV/AV 8. LAMP INDICATOR to 9. TEMPERATURE INDICATOR to p.7) p.7) selects the remote switches the set 3. 10. MAIN POWER MENU selects 4. operating mode. on from standby. (Refer 10 OK Note accepts your selection or displays the current mode. : center of the might on or be screen a F / G 5. (Volume Down/Up) adjusts the volume. adjusts menu settings. 6. D / E (Programme Up/Down) selects programme or a menu item. switches the set on from standby. a p.7) off. faint white trace according This is normal and is screen. 6 There to (ON/OFF) switches the set a menu. (Refer a to the on the position. characteristic of the Location and function of controls Rear panel AV4 INPUT (R) SOCKET AUDIO (L)/ MONO VIDEO S-VIDEO S-VIDEO INPUT SOCKET COMPONENT NPUT2 R) NPUT1 DO AV1 AV2 AV3 PC/DTV 480i480p/ 576i576p/ 480i480p/ 576i576p/ 720p1080i 720p/1080i L/ IDO MNO Y SXGA/ IDEO S 480p/ 56p/ PB 720p/ 1080i) PR AV3 INPUT RGBINPUT U P P G O R R A T D E (L) (L) AUDO AUDO (R) (R) AV4 INPUT DVI/ RGBNPUT HDMIDVI NPUT UPGRADE PORT This port is used to the software version and debug without changing the hardware. Be careful not to use this port. Just contact your dealer or service centre. upgrade COMPONENT INPUT 1 INPUT 2 480i/480p/ 576i/576p/ 720p/1080i AV1 AV2 AV3 480i/480p/ 576i/576p/ 720p/1080i PC/DTV Y (XGA/ 480p/ 576p/ 720p/ 1080i) AV1/AV2/AV3 INPUT SOCKETS DTV/DVD INPUT PB PR RGB INPUT U P P G O R R (L) (L) AUDIO A T D E AUDIO (R) (R) DVI / RGB INPUT HDMI/DVI AERIAL HDMI/DVI SOCKET RGB INPUT ?Status Indicators Operation Indicator Off Power cord is not connected Red Power Cord is Green On Orange (flashing) Preparing operation Orange Projection lamp needs to be Red Lamp (flashing) Indicator Red a Contact an Lamp Green (flashing) Red Temperature There is The lamp Indicator (flashing) Orange is in replaced on standby. standby. reaching problem with the end of its life and a new with the lamp lamp. or around it. authorized service center. over. cover viewing is not closed. the phrase The set has shut Thermal power switch is off connected, unit is The set has shut down due to After Red life or overheating. "Thermal High Error" down, check the cooling fan. warning. 7 Basic Operation On and off 1. 2. POWER 3. MULTIMEDIA TV/AV MUTE SWAP MENU VOL PR OK VOL Before turning the set on, be sure that the main power switch on the set is pushed on. When the main switch is pushed on, the LED will be lit up red. This mode is Stand-by. If the set is in stand-by mode, press the POWER, D / E, TV/AV, MULTIMEDIA or NUMBER button on the remote control handset to turn it on fully. The LED will blink orange for a while and then lit up green when the power is successfully on. To turn the set off, press the power button on the remote control handset. The set reverts to the stand-by mode. Note : a. The lamp cooling fan will continue to spin for approximately 120 seconds after the power is turned off by the remote control handset. b. Normally, don't push off the main power switch. Instead, use the remote control to turn the power off. c. When the set is turned on again immediately after turning off, it takes around 20 to 40 seconds for sufficient cooling. d. When the power is switched off using the main power switch on the set, the internal cooling system also stops operating. Therefore, power-on by main power switch takes around 30 to 50 seconds for sufficient cooling. e. Forced Power-Off : When the set decides itself that the circumstance is not proper for operation, the set will goes to the standby mode automatically. Please retry to turn on the set after a short period of time. f. When the set is switched on, there might be a strange sound from the set. PR 123 456 7 8 9 0 SSM Programme selection You can select buttons. a Volume programme number with the D / E or NUMBER adjustment Press the F / G button to adjust the volume. Quick view Press the SWAP button to view the last programme you were watching. Note I/II This function works only when Favourite programme is set to Off. Otherwise each press of this button will select a stored favourite programme. : Mute function Press the MUTE button. The sound is switched off and the appears. You can cancel it 8 by pressing the MUTE, F / G, SSM, display I/II button. On Screen Menus The dialogue between you and your set takes place required for the operating steps are also displayed. on screen with an operator menu. The buttons Menu selection 1. Press the MENU button and then D / E button to 2. Press the G button and then the D / E button to select 3. Repeatedly display each a menu press the MENU button to return to normal TV STATION G Auto programme menu. item. viewing. STATION PSM PICTURE G CSM Manual programme PICTURE Programme edit Favourite programme ACM SOUND SOUND TIME TIME SPECIAL SPECIAL SCREEN SCREEN PIP/DW PIP/DW STATION STATION STATION PICTURE PIP 50 Sharpness 60 Balance SOUND Win. position PIP menu Transparency PIP System G 0 Equalizer TIME SPECIAL SCREEN PIP/DW Colour AVL Input Win. size SPECIAL 50 BBE PIP TIME Brightness SSM DW SOUND 95 PICTURE menu Input PICTURE Contrast SCREEN PIP/DW G PIP/DW STATION Auto config. Manual PICTURE SOUND menu STATION STATION Child lock PICTURE ARC Clock Demo config. Off time PICTURE On time Cinema SOUND Auto SOUND SOUND TIME TIME SPECIAL SPECIAL G SPECIAL SCREEN G SCREEN SCREEN PIP/DW PIP/DW PIP/DW TIME NR Reset SCREEN menu SPECIAL menu menu sleep G TIME menu 9 STATION MENU Up to 100 TV stations can be stored in this set bers STATION G Auto programme Manual programme PICTURE Programme edit Favourite programme SOUND num- Once you have preset the stations, you will be able the D / E or NUMBER buttons to scan the stations you pro- (0 to use by programme to 99). grammed. Stations can be tuned using automatic manual modes. or TIME Auto programme SPECIAL SCREEN tuning All stations that can be received are stored by this method. It is recommended that you use auto programme during installation of this PIP/DW set. 1. 2. Press the MENU button and then D / E button to select the STATION menu. Press the G button and then D / E button to select Auto pro- gramme. 3. Press the G button to select the F / G button; STATION Auto programme G Manual programme PICTURE Select System. Programme edit Favourite programme System Storage a TV system with BG from 2 Start SOUND TIME SPECIAL SCREEN MENU VOL PR OK PIP/DW VOL 4. BG : I DK : M : : 5. Prev. PAL B/G, SECAM B/G PAL I/II (U.K./Ireland) PAL D/K, SECAM D/K (Europe/East Europe) (East Europe) (USA/Korea/Philippines) (option) Press the E button to select Storage ning programme PR Menu from. Select the begin- number with the F / G button or NUMBER but- tons on the Storage from menu. Press the E button to select Start. 123 STATION Auto programme Manual programme 456 PICTURE Programme edit Favourite programme 78 System Storage 2 Auto programme TIME 0 from Start SOUND 9 BG ----- SPECIAL 16 M 23% SCREEN PIP/DW 6. 7. Stop Prev. Press the G button to begin auto programming. All receivable stations are stored. The station name is stored for stations which broadcast VPS (Video Programme Service), PDC (Programme Delivery Control) or TELETEXT data. If no station name can be assigned to a station, the channel number is assigned and stored as C (V/UHF 01-69) or S (Cable 01-47), followed by a number. To stop auto programming, press the MENU button. When auto programming is completed, the Programme edit menu appears on the screen. See the 'Programme Edit' section to edit the stored programme. Repeatedly Press the MENU button to return to normal TV viewing. 10 Menu STATION MENU Manual programme tuning STATION G Manual programme Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign a station name Auto programme PICTURE Programme edit Favourite programme SOUND with five characters to each programme number. TIME SPECIAL 1. STATION 2. / E Press the MENU button and then D button to select the SCREEN PIP/DW menu. Press the G button and then D / E button to select Manual programme. STATION Auto programme Manual programme PICTURE Programme Storage 2 System BG G edit Favourite programme Band V/UHF SOUND Channel TIME Fine SPECIAL Search 1 Name SCREEN PIP/DW 3. C01 Press the G button to select Storage. F number with the programme on the Storage menu. 4. Press the E button to select the F 5. / G button Select the or beginning NUMBER buttons Select System. a TV button; PAL B/G, SECAM B/G (Europe/East Europe) : I : PAL I/II DK : PAL M : (USA/Korea/Philippines) (option) PR VOL OK VOL (U.K./Ireland) D/K, SECAM D/K (East Europe) Press the E button to select Band. Press the F V/UHF or Cable as / G button to required. PR 123 Press the E button to select Channel. Select the desired channel number with the F possible, / G button select the channel number or NUMBER buttons. If directly with the number buttons. 7. MENU system with / G BG select 6. Off Booster Prev. Menu 78 9 0 Press the E button to select Search. Press the F commence 456 searching. If a / G button to station is found the search will 8. Press the OK button to store it. 9. To store another 10. Repeatedly viewing. station, repeat steps 3 stop. to 8. press the MENU button to return to normal TV 11 STATION MENU STATION G Auto programme Manual programme PICTURE Programme edit Favourite programme Assigning a station name 1. Repeat the 'Manual programme tuning' steps 2. 3. SOUND TIME 4. SPECIAL SCREEN 5. 6. PIP/DW 1 to 2. Press the E button to select Name. Press the G button. You can use a blank, +, -, the numeric 0 to 9 and the alphabet A to Z. With the E button you can select in the opposite direction. Select the next position by pressing the G button and then take your choice of the second character, and so on. Press the OK button. Repeatedly press the MENU button to return to normal TV viewing. Booster (option) In some models, Booster is an optional function. Booster can perform this function. Only a set with If the reception is poor at the fringe area of TV signal, select Booster to On. When the picture condition is good, do not select Booster to On. MENU 1. 2. 3. 4. PR the 'Manual programme tuning' steps 1 to 2. Press the E button to select Booster. Press the F / G button to select On or Off. Repeatedly press the MENU button to return to normal TV Repeat viewing. VOL OK VOL Fine tuning Normally 1. 2. fine tuning is only necessary if reception the 'Manual programme tuning' Press the E button to select Fine. Repeat steps is poor. 1 to 2. PR STATION Auto programme Manual programme PICTURE Programme Storage 2 System BG G edit Favourite programme Band V/UHF SOUND Channel TIME Fine SPECIAL Search Name SCREEN PIP/DW 3. 4. 5. Menu C01 Off Prev. Press the F / G button to fine tune for the best picture and sound. Press the OK button. The finely tuned programme will be indicated by yellow number during programme selection. Repeatedly press the MENU button to return to normal TV viewing. 12 Booster 1 STATION MENU Programme edit This function enables you to delete or skip the stored programmes. Also you can move some stations to other programme numbers or copy a blank station data into the selected programme number. 1. 2. 3. STATION G Manual programme PICTURE 0- - - - - edit SOUND TIME SPECIAL SCREEN PIP/DW edit 5C05 1BLN2 6C07 2C01 7C55 3C04 8S27 4C05 9S29 Delete Copy Move Skip Menu Programme Favourite programme Press the MENU button and then D / E button to select the STATION menu. Press the G button and then D button to select / E Programme edit. Press the G button to display the Programme edit menu. Programme Auto programme Prev. Deleting a programme 1. SelectaprogrammetobedeletedwiththeD/EorF/Gbutton. 2. Press the RED button twice. The selected programme is deleted, grammes are shifted up one position. MENU all the following PR pro- Copying a programme 1. SelectaprogrammetobecopiedwiththeD/EorF/Gbut- VOL OK VOL ton. 2. 3. Press the GREEN button. Move the programme to the desired programme number with the D/EorF/Gbutton. 4. Press the GREEN button again to move the programme. All the following programmes are shifted down one position. Moving a programme 1. SelectaprogrammetobemovedwiththeD/EorF/Gbutton. 2. 3. Press the YELLOW button. Move the programme to the desired programme number with the PR 123 456 78 9 0 D/EorF/Gbutton. 4. Press the YELLOW button Skipping 1. 2. 3. a again to release this function. programme number programme number to be Select a skipped with the D / E or F / G button. Press the BLUE button. The skipped programme turns to blue. Press the BLUE button again to release the skipped pro- gramme. When a programme number is skipped it means that you will be unable to select it using the D / E button during normal TV viewing. If you want to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in the programme edit or table menu. Repeatedly press the MENU button to return to normal TV viewing. 13 STATION MENU Favourite STATION G Auto programme Programme This function lets you select your favourite programmes directly. Manual programme PICTURE Programme edit 1. Favourite programme SOUND 2. TIME Press the MENU button and then use D / E button to select the STATION menu. Press the G button and then D / E button to select Favourite programme. SPECIAL 3. SCREEN Press the G button to PIP/DW display STATION PICTURE the Favourite programme Auto programme On Manual programme Off Programme edit Favourite programme menu. 0BLN2 G - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - SOUND TIME SPECIAL SCREEN PIP/DW 4. 5. 6. 7. SWAP MENU 8. 9. PR Menu Prev. Press the D / E button to select On. Press the G button and then D / E button to select -----. Select a desired programme with the F / G button or NUMBER buttons. Any number under 10 is entered with a numeric '0' in front of it, i.e. '05' for 5. To store another programme, repeat steps 5 to 6. You can store up to 8 programmes. Press the OK button. Repeatedly press the MENU button to return to normal TV -- viewing. Repeatedly VOL OK VOL press the SWAP button to select stored favorite pro- grammes. Calling the programme table You can check the programmes stored in the memory the programme table. PR Displaying programme by displaying table Press the LIST button to display the Programme table The programme table appears on the screen. 0- - - - - menu. 5C05 1BLN2 6C07 2C01 7C55 3C04 8S27 4C05 9S29 LIST Note : a. You may find some blue highlighted programmes shown. They have been set up in the programme edit mode. b. Some programmes with the channel number shown in the programme table indicate there is no station name assigned. programme in the programme table Select a programme with the D / E or F / G button. The set switches to the chosen programme number. Selecting a Paging through a programme table There are 10 (or 20) programme table pages which contain 100 (or 200) programmes. Pressing the D / E or F / G button repeatedly turns the pages. Press the LIST button to return to normal TV 14 viewing. PICTURE MENU PSM 1. 2. (Picture Status Memory) Press the MENU button and then D TURE menu. Press the G button and then D / E / E STATION PSM PICTURE G CSM button to select the PIC- ACM SOUND button to select PSM. TIME SPECIAL STATION G PSM TIME SPECIAL Brightness 50 Colour 50 Sharpness 60 SCREEN CSM Mild ACM SOUND 95 Dynamic Standard PICTURE Contrast Contrast 95 Brightness 50 Colour 50 Sharpness 60 PIP/DW User SCREEN PIP/DW Menu Prev. 3. Press the G button and then D / E button to select ting on the PSM pull-down menu. 4. Press the OK 5. Repeatedly viewing. or a picture set- F button. press the MENU button to return to normal TV preferred setting, press the PSM button until the (Dynamic, Standard, Mild or User) appears. The picture Dynamic, Standard and Mild are programmed for good picture reproduction at the factory and cannot be changed. To recall your desired picture VOL (Excellent Digital) - You can Reality enjoy MENU the vivid and high-definition picture with PR OK VOL Digital technology. When selecting picture options (Dynamic, Standard and Mild) in PICTURE menu, XD is automatically changed to On. -It's not available to use this function in RGB[PC], HDMI[PC] processor - PR mode. 1. 2. Press the MENU button and then D / E button to select the PICTURE menu. Press the G button and then D / E button to select XD. STATION PSM G PICTURE PSM CSM On Off ACM SOUND TIME SPECIAL Contrast 95 Brightness 50 Colour 50 Sharpness 60 SCREEN PIP/DW 3. 4. 5. Menu Prev. Press the G button and then D / E button to select On or Off. Press the OK or F button. Repeatedly press the MENU button to return to normal TV viewing. 15 PICTURE MENU CSM STATION PSM - PICTURE G CSM ACM SOUND TIME SPECIAL Contrast 95 Brightness 50 Colour 50 Sharpness 60 SCREEN (Color Starus Memory) When selecting picture options (Dynamic, Standard and Mild) in PICTURE menu, CSM is automatically changed to Normal. -I t 's not available to 1. PIP/DW 2. use this function in sRGB On mode. Press the MENU button and then D / E button to select the PICTURE menu. Press the G button and then D / E button to select CSM. STATION PSM PICTURE CSM G Cool ACM SOUND TIME SPECIAL Normal Contrast 95 Brightness 50 Colour 50 Sharpness 60 Warm User SCREEN PIP/DW MENU VOL PR OK Menu 0 Green 0 Blue 0 Prev. 3. Press the G button and then desired colour temperature. 4. Press the OK 5. Repeatedly viewing. or Red use D / E button to select the F button. press the MENU button to return to normal TV VOL Manual Colour 1. Temperature Control (User option) Press the MENU button and then D PICTURE menu. / E button to select the PR STATION PSM PICTURE CSM G Cool ACM SOUND TIME SPECIAL Normal Contrast 95 Brightness 50 Colour 50 Sharpness 60 Warm User SCREEN PIP/DW 0 Green 0 Blue 0 Prev. / E 3. Press the G button and then D Press the G button and then D 4. Press the G button and then F / G 2. adjustments. The adjustment 5. 6. / button to select CSM. E button to select User. button to make appropriate range of Red, Green and Blue is -30~+30. Press the OK button. Repeatedly press the MENU button to return to normal TV viewing. 16 Menu Red PICTURE MENU sRGB - When the set only) equipment with sRGB difference to display the equal STATION PSM PICTURE G CSM connected to external was function, It's adjusted image mode (RGB[PC], HDMI[PC] colour a each other. ACM SOUND TIME SPECIAL 2. Press the MENU button and then D / E button to select the PICTURE menu. Press the G button and then D / E button to select sRGB. 3. Press the G button and then D 1. STATION PSM PICTURE CSM s-RGB SOUND TIME button to select On / E G Contrast 95 Brightness 50 or Contrast 95 Brightness 50 Colour 50 Sharpness 60 SCREEN PIP/DW Off. On Off SPECIAL SCREEN PIP/DW 4. Press the OK 5. Repeatedly viewing. ACM - - or Menu Prev. F button. press the MENU button to return to normal TV MENU (Active Color Management) VOL the ACM to select the desired skin colour This function works in the following mode: Adjust , this function in XD Off mode. 1. Press the MENU button and then PICTURE menu. 2. Press the G button and then use 3. Press the G button and then use STATION PSM PICTURE CSM G ACM SOUND TIME SPECIAL Contrast 95 Brightness 50 Colour 50 Sharpness 60 use VOL HDMI DTV [480p, 570p, 720p,1080i]. use OK option. TV, AV1, AV2, SAV2, AV3, AV4 COMPONENT 1/2 -I t 's not available to PR PR D / E button to select the D / E button to select ACM. F / G button to make appro- Fleshtone 0 Greentone 0 Bluetone 0 SCREEN PIP/DW priate adjustments. The adjustment range 4. 5. Menu Prev. of ACM is 0 3. ~ Press the OK button. Repeatedly press the MENU button to return to normal TV viewing. 17 PICTURE MENU Manual Picture Control STATION PICTURE G PSM You CSM ACM SOUND TIME SPECIAL (User option) Contrast 95 Brightness 50 Colour 50 Sharpness 60 adjust picture contrast, brightness, colour, sharpness tint (NTSC input only) to the levels you prefer. In the broadcasting system PAL/SECAM, the picture item can and Tint doesn't work. SCREEN PIP/DW 1. Press the MENU button and then D TURE menu. / E 2. Press the G button and then D picture item. button to select the desired STATION PSM PICTURE CSM / E button to select the PIC- ACM SOUND TIME SPECIAL Contrast 95G Brightness 50 Colour 50 Sharpness 60 SCREEN PIP/DW 3. 4. PR 5. Prev. Press the G button and then F adjustments, MENU Menu / G button to make then it will be stored for the picture appropriate User. Press the OK button. Repeatedly press the MENU button to return to normal TV viewing. VOL OK VOL adjustment for PICTURE colour, sharpness and tint) affect both Note PIP PR 18 : or The Twin Picture mode. (contrast, brightness, main and sub picture in menu the SOUND MENU SSM (Sound Status Memory) This function lets you enjoy the best sound without any special adjustment because the set automatically selects the appropriate sound option based on the program content. When adjusting sound options equalizer manually, SSM is auto- matically changed 1. 2. Press the MENU button and then D / E button to select the SOUND menu. Press the G button and then D / E button to select SSM. SSM G BBE PICTURE BBE PICTURE AVL Balance SOUND G 0 Equalizer SPECIAL SCREEN PIP/DW SRS TSXT Flat AVL Balance SOUND SSM TIME to User. STATION STATION 0 Music Movie Equalizer Speech TIME User SPECIAL SCREEN PIP/DW 3. 4. 5. Menu Prev. Press the G button and then D / E button to select a sound setting on the SSM pull-down menu. Press the OK or F button. Repeatedly press the MENU button to return to normal TV viewing. To recall your preferred setting, press the SSM button until the desired sound (SRS TSXT, Flat, Music, Movie, Speech or User) appears. The sound SRS TSXT, Flat, Music, Movie and Speech are programmed for good sound reproduction at the factory and cannot be changed. Note : If you press the SSM button after making appropriate adjusta. ment on the Equalizer sub menu, the display User automatically appears even though you have already set a factory preset setting; SRS TSXT, Flat, Music, Movie or Speech. b. Equalizer isn't suitable to use SRS TSXT. MENU VOL PR OK VOL PR R - - is a trademark of SRS TruSurround XT technology is SRS Labs, Inc. Labs, Inc. incorporated under license from BBE - BBE ter High Definition Sound speech intelligibility and -I t 's not available to 1. 2. SSM use and presence for betmusical realism. this function in SRS TSXT mode. restores clarity Press the MENU button and then D / E button to select the SOUND menu. Press the G button and then D / E button to select BBE. STATION SSM BBE PICTURE G Off AVL Balance SOUND On 0 Equalizer TIME SPECIAL SCREEN PIP/DW 3. 4. 5. Menu Prev. Press the G button and then D / E button to select On or Off. Press the OK or F button. Repeatedly press the MENU button to return to normal TV viewing. 19 SOUND MENU AVL STATION SSM BBE PICTURE AVL Balance SOUND (Auto Volume Leveler) G 0 Equalizer If you select AVL On, the set automatically ume level even if you change programmes. keeps on an equal vol- TIME SPECIAL 1. Press the MENU button and then D / E button to select the SOUND menu. 2. Pressthe Gbutton andthenD /Ebuttonto selectAVL. SCREEN PIP/DW STATION SSM BBE PICTURE G AVL Balance SOUND 0 On Off Equalizer TIME SPECIAL SCREEN PIP/DW 3. 4. 5. Menu Prev. Press the G button and then D / E button to select On or Off. Press the OK or F button. Repeatedly press the MENU button to return to normal TV viewing. MENU PR Balance VOL OK PR VOL You can adjustment adjust balance. 1. Press the MENU button and then D / E button to select the SOUND menu. 2. Press the G button and then D / E button to select Balance. STATION SSM BBE PICTURE AVL Balance SOUND 0G LR Equalizer TIME SPECIAL SCREEN PIP/DW 3. Press the G button. 4. Make desired pull-down 5. 6. adjustment Prev. with the F / G button on the Balance menu. Press the OK button. Repeatedly press the MENU button to return to normal TV viewing. 20 Menu SOUND MENU Equalizer (option) STATION 1. Press the MENU button and then D / E button to select the SOUND menu. BBE PICTURE 3. AVL Balance SOUND Press the G button and then D / E button to select Equalizer. Press the G button in Equalizer to display the Equalizer sub 2. SSM G 0 Equalizer TIME SPECIAL menu. SCREEN PIP/DW STATION SSM BBE PICTURE SOUND 120 AVL 200 Balance 0 Equalizer G 500 1.2K TIME 3K 7.5K SPECIAL 12K SCREEN PIP/DW 4. 5. 6. 7. Select Prev. the D / E button. Make appropriate sound level with the F / G button. Press the OK button. Repeatedly press the MENU button to return to normal TV a sound band Menu by pressing viewing. MENU PR Sound output selection In AV mode, you can select output sound for the left and right loud- VOL OK VOL speakers. press the I/II button to select the sound output. Audio signal from audio L input is sent to the left loud speaker and audio signal from audio R input is sent to the right loud speaker. Audio signal from audio L input is sent to left and right loud- Repeatedly L+R : L+L : R+R : speakers. Audio signal speakers. from audio R input is sent to left and right PR loud- I/II 21 SOUND MENU Stereo/Dual When reception programme is selected, the sound information for the station appears after the programme number and station name disappear. a Broadcast On Screen Mono MONO Stereo STEREO Dual DUAL I Display Mono sound selection In stereo reception if the stereo signal is weak, you can switch to mono by pressing the I/II button twice. In mono reception the depth of sound is improved. To switch back to stereo, press the I/II button twice again. selection for dual language broadcast If a programme received in two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II by pressing the I/II button repeatedly. DUAL I sends the primary broadcast language to the loudspeakers. DUAL II sends the secondary broadcast language to the loudspeakers. DUAL I+II sends a separate language to each loudspeaker. Language NICAM reception If your set is I/II with the receiver for NICAM reception, the Companding Sound high quality NICAM (Near Instantaneous Multiplex) digital sound can be received. Sound output can be selected according to the type of received broadcast as follows by pressing the I/II button repeatedly. 1. When NICAM MONO 2. When or FM 3. mono is received, you can select NICAM is received, you can select NICAM FM MONO. NICAM stereo STEREO 22 equipped or FM MONO. If the stereo signal is weak, switch to mono. When NICAM dual is received, you NICAM DUAL II NICAM DUAL I+II or can select NICAM DUAL or MONO. I, TIME MENU Clock You must set the time before correctly on/off time function. using STATION Clock Off time PICTURE 1. 2. Press the MENU button and then D / E button to select the TIME menu. Press the G button and then D / E button to select Clock. On time Auto SOUND TIME sleep G SPECIAL SCREEN STATION Clock G : -- -- PIP/DW Off time PICTURE On time Auto sleep SOUND TIME SPECIAL SCREEN PIP/DW Prev. Menu 3. Press the G button and then use D / E button to adjust the 4. hour. Press the G button and then use D / E button to adjust the minute. 5. 6. Press the OK button. Repeatedly press the MENU button to return to normal TV viewing. MENU PR On/Off Timer Timer function operates only if Off Timer function overrides time. The TV must be in current time has been on Timer function if they already are set. VOL OK VOL set to the same 1. 2. standby mode for the On Timer to work. Press the MENU button and then D / E button to select the TIME menu. Press the G Time or button and then use PR D / E button to select Off On Time. STATION Clock Off time PICTURE On time Auto G On Off sleep SOUND 12 TIME : Volume Programme SPECIAL 00 30 1 SCREEN PIP/DW Menu Prev. 3. Press the G button and then 4. Press the G D / E button to select On. button and then use D / E button to adjust the use hour. 5. Press the G button and then use D / E button to adjust the minute. 6. 7. 8. Time function ; Press the G button and then use D / E button to adjust volume level and programme number. Press the OK button. Repeatedly press the MENU button to return to normal TV Only On viewing. 23 TIME MENU Auto STATION Clock If there is Off time PICTURE no On time Auto SOUND TIME sleep input signal, the TV turn off automatically after 10 min- utes. sleep G SPECIAL 1. Press the MENU button and then D / E button to select the TIME menu. 2. Press the G button and then D SCREEN PIP/DW / E button to select Auto sleep. STATION Clock Off time PICTURE On time Auto sleep GOn Off SOUND TIME SPECIAL SCREEN PIP/DW SLEEP 3. 4. 5. Menu Prev. Press the G button and then D / E button to select On or Off. Press the OK or F button. Repeatedly press the MENU button to return to normal TV viewing. MENU PR Sleep VOL OK VOL Sleep Timer timer turns the set off at the preset time. Press the SLEEP button to select the number of minutes. The diszz Min will appear on the screen, followed by 10, 20, 30, play --- 60, 90, 120, 180 and 240 minutes. The timer begins PR to count down from the number of minutes selected. Note : a. To check the remaining sleep time, press the SLEEP button once. b. To cancel the sleep time, repeatedly press the SLEEP button zz Min appears. until the display c. If you turn the set off after setting the sleep timer, the setting will be erased. --- 24 SPECIAL MENU Child Lock STATION The TV can be set so that the remote control handset is needed to control it. This feature can be used to prevent unauthorized view- ing. Child lock Demo PICTURE SOUND TIME SPECIAL G 1. 2. Press the MENU button and then D / E button to select the SPECIAL menu. Press the G button and then D / E button to select Child lock. Child lock STATION SCREEN PIP/DW GOn Off Demo PICTURE SOUND TIME SPECIAL SCREEN PIP/DW 3. 4. 5. Menu Prev. Press the G button and then D / E button to select On or Off. Press the OK or F button. Repeatedly press the MENU button to return to normal TV viewing. MENU With the lock on, the display Child lock On appears on the screen if any button on the front panel is pressed while viewing the TV. VOL PR OK CANCEL/EXIT VOL Demo Use it to see the difference between XD demo It's not available to use this function in on and XD Demo off. RGB[PC], HDMI[PC] mode. 1. Press the MENU button and then D / E button to select the SPECIAL menu. 2. Press the G button and then D / E button to select XD Demo. STATION PR Child lock Demo G To start PICTURE SOUND TIME SPECIAL SCREEN PIP/DW Menu 3. Press the G button to 4. To stop XD Demo, Prev. XD Demo. press the CANCEL/EXIT button. begin 25 SCREEN MENU Auto STATION Auto PICTURE config. ARC 1. Cinema SOUND NR Reset 2. TIME mode only) and minimizes Automatically adjusts picture position config. Manual Configuration (RGB [PC] image shaking. Press the MENU button and then use D / E button to select the SCREEN menu. Press the G button and then use D / E button to select Auto config.. SPECIAL SCREEN G PIP/DW STATION Auto config. Manual PICTURE G To set config. ARC Cinema SOUND NR Reset TIME SPECIAL SCREEN PIP/DW 3. Menu Prev. Press the G button to start Auto config.. When Auto config. has finished, Ok will be shown on screen. If the position of the image is still not correct, try Auto adjustment 4. 5. MENU PR again. If picture needs to be adjusted more after Auto adjustment in RGB (PC), you can adjust the Manual config.. Repeatedly press the MENU button to return to normal TV viewing. Note a. VOL OK VOL b. : Although the image is still not correct, your properly but needs further adjustment. The Auto config. functions don't need to set is be functioning run for HDMI mode. Manual PR Configuration If the picture isn't clear after auto adjustment and especially that characters are still trembling, adjust the picture phase manually. This function works in the following mode NENT[480p, 576p, 720p, 1080i] mode only. 1. 2. : RGB, HDMI, COMPO- Press the MENU button and then use D / E button to select the SCREEN menu. Press the G button and then D / E button to select Manual config.. STATION Auto config. Phase 0 H Size 0 V Size 0 TIME H Position 0 SPECIAL V Position 0 Manual PICTURE config. ARC Cinema SOUND G NR Reset SCREEN PIP/DW 3. 4. 5. Menu Prev. Press the G button and then D / E button to select Phase, H Size, V Size, H Position or V Position. Press the F / G button to make appropriate adjustments. Repeatedly press the MENU button to return to normal TV viewing. Note : It's available to use H Position, V Position function in HDMI, COMPONENT [480p, 576p, 720p, 1080i] mode. 26 SCREEN MENU Setting Picture Format You can watch the screen in various picture formats ; Spectacle, Full (option), Original, 4:3, 16:9 (Wide), 14:9 and Zoom. STATION Auto config. Manual PICTURE config. ARC Cinema 1. Press the MENU button and then use D / E button to select the SOUND 2. SCREEN menu. Press the G button and then TIME use D / E button to select ARC. NR Reset SPECIAL SCREEN G PIP/DW STATION Auto config. Manual PICTURE SOUND config. ARC G Cinema Spectacle Original NR 4:3 16:9 Reset TIME 14:9 Zoom SPECIAL SCREEN PIP/DW 3. Menu Prev. Press the G button and then use D / E button to select Spectacle, Full (option), Original, 4:3, 16:9, 14:9 or Zoom. Spectacle When your TV receives the wide screen signal, following selection will lead you to adjust the picture horizontally, in a linear proportion, to fill the entire screen. Full (option) When your TV receives the wide screen signal, following selection will lead you to adjust the picture horizontally or vertically, in a linear proportion, to fill the entire screen fully. MENU VOL PR OK VOL Original When your TV receives the wide screen signal, it will be automatically changed to the picture format to be sent. 4:3 selection will lead you to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides. Following PR 16:9 (Wide) Following selection will lead you to adjust the picture horizontally, in a linear proportion, to fill the entire screen (useful for viewing 4:3 formatted DVDs). 14:9 You enjoy the picture format of 14:9 or general TV programme through the 14:9 mode. The screen 14:9 is viewed just like that the screen 4:3 is magnified to the left / right. can ARC Zoom selection will lead you to view the picture without any alternation, while filling the entire screen. However, the top and bottom portions of the picture will be cropped. Following 4. Repeatedly press viewing. Note : You can only the MENU button to return to normal TV select 4:3 and 16:9 (Wide) in RGB and HDMI. 27 SCREEN MENU Cinema STATION Auto config. Manual PICTURE When you watch the config. ARC set to the best picture appearance. This function works in the following mode AV3, AV4 or COMPONENT (480i/576i.) Cinema SOUND movie, this function adjusts the NR Reset TIME SPECIAL : TV, AV1, AV2, SAV2, SCREEN G PIP/DW 1. Press the MENU button and then D / E button to select the SCREEN menu. 2. Press the G button and then D / E button to select Cinema. STATION Auto config. Manual PICTURE config. ARC GOn Cinema SOUND TIME Off NR Reset SPECIAL SCREEN PIP/DW 3. 4. MENU VOL 5. PR OK PR VOL NR Menu Prev. Press the G button and then D Press the OK or F button. Repeatedly viewing. / E button to select On or Off. press the MENU button to return to normal TV (Noise Reduction) 1. Press the MENU button and then D / E button to select the SCREEN menu. 2. Press the G button and then D / E button to select NR. STATION Auto config. Manual PICTURE config. ARC Cinema SOUND NR G Reset TIME 3DNR 0 MPEG NR 0 SPECIAL SCREEN PIP/DW 3. Menu Prev. Press the G button and then use D / E button to select 3D NR MPEG NR. Press the F / G button to make appropriate adjustments. The adjustment range of 3D NR is 0 2. The adjustment range of MPEG NR is 0 15. Press the OK button. Repeatedly press the MENU button to return to normal TV or 4. ~ ~ 5. 6. viewing. Note : It's available to use 3D NR function in TV, AV1, AV2, SAV2 ,AV3, AV4 or COMPONENT (480i/576i) mode. 28 SCREEN MENU to Initializing (Reset original factory value) STATION This function operates in To initialize the adjusted current mode. value. Auto config. Manual PICTURE config. ARC Cinema SOUND NR Reset TIME 1. 2. Press the MENU button and then D / E button to select the SCREEN menu. SPECIAL SCREEN G Press the G button and then D / E button to select Reset. STATION Auto config. Manual PICTURE PIP/DW config. ARC Cinema SOUND NR Reset G Toset TIME SPECIAL SCREEN PIP/DW 3. Menu Prev. Press the G button. You Position, PIP size, PIP position, PIP Transparency, Phase, H Size, V Size, H position, V position and sub can picture initialize size of twin picture. MENU VOL PR OK VOL PR 29 PIP/DW MENU Main Picture Source Selection STATION Input Inputs DW PICTURE PIP PIP SOUND TIME SPECIAL position PIP Transparency PIP System TV, AV, Component equipment a RGB, HDMI mode. AV or video cassette recorder (VCR), or other is connected to the set. Note : When a VCR is connected via the aerial socket the set is used in TV mode. See the 'Connection of external equipment' section. SCREEN PIP/DW be set for mode is used when Input Win. size Win. can G 1. Press the MENU button and then D / E button to select the PIP/DW menu. 2. Press the G button and then D / E button to select Input. Press the G button and then D / E button to select TV,AV1, AV 2 SAV2, AV 3 AV4 Component1, Component2 or RGB, 3. , TV/AV , , HDMI/DVI. STATION PICTURE TIME SPECIAL TV DW AV1 PIP AV2 PIP SOUND G Input Input SAV2 Win. size AV3 Win. AV4 position PIP Transparency Component1 PIP System Component2 RGB MENU PIP/DW VOL OK AV1 AV2 VOL : : 123 Prev. VCR connected to the Euro scart socket 1 VCR connected to the Euro scart socket 2 SAV2 : AV3 : VCR connected to the Euro scart socket 3 AV4 : on on VCR connected to the Euro scart socket 2 the set the set on on the set the set set 456 HDMI/DVI 0 Menu VCR connected to the AV4 INPUT sockets of the set Component1/2 : DVD connected to the DTV/DVD INPUT sockets on the back of set RGB : PC connected to the RGB INPUT sockets on the back of PR 78 HDMI/DVI SCREEN PR 9 4. 5. : DTV/DVD INPUT connected to the HDMI/DVI INPUT sockets on the back of set Press the OK or F button. Repeatedly press the MENU button to return to normal TV viewing. Alternatively you can select the TV, AV, Component mode by pressing the TV/AV button. In AV, Component press the D / E 30 or or RGB, HDMI mode, NUMBER buttons. or RGB, HDMI to return to TV mode, Picture In Picture Option : PIP (Picture In Picture) displays a picture within the sub picture. a (PIP) Function picture. On and off Press the PIP button to switch on Press CANCEL/EXIT button to switch it off. Each press of PIP button button changes the shown below. screen display as PIP PR- SWAP PR+ INPUT CANCEL/EXIT Note ture : When the sub picture size is 1/2 of the main picture, the pic- quality might get poor. Input mode selection for sub Press the INPUT button to select the picture input mode for the sub picture. Note : a. When the PIP function is switched on, you can also adjust it in the PIP/DW menu. b. In some models, when the sub picture quality get poor for sub picture, select Auto, PAL, SECAM or NTSC in PIP System menu. Swapping between main and sub Press the SWAP button to Note : When the main available. Programme The sub the main and sub exchange picture is TV pictures or selection for sub AV pictures. modes, the swapping is picture programme selection is available when the sub picture is TV mode. Press the PR +/- buttons to select a programme for the sub picture. picture 31 Picture In Picture Sub picture (PIP) Function size Press the SIZE button and then F / G button to ture picture size. adjust the sub pic- With SIZE button in DW1, DW2 modes, main and sub picture is adjusted simultaneously. With SIZE button in PIP mode, sub picture is adjusted. Sub picture position change Press the POSITION button. Repeatedly press the D / E is achieved. The sub picture MENU Adjusting PR 1. VOL VOL 2. PIP or F / G moves button until desired up/down Transparency (PIP or position left/right. mode only) Press the MENU button and then D / E button to select the PIP/DW menu. Press the G button and then D / E button to select PIP Transparency. 3. Press the G button and then F / G button to 4. parency. The adjustment range of PIP Transparency is 0 10. Repeatedly press the MENU button to return to normal TV adjust PIP trans- ~ PR viewing. POSITION 32 SIZE Teletext Teletext (or TOP with the teletext Teletext is a text) is system an can grammes, share on by most TV stations which news, and many other The teletext decoder of this TV FASTEXT only a set receive the teletext broadcast. information prices therefore optional function, free service broadcast up-to-the-minute (option) can gives weather, television pro- topics. support the SIMPLE, TOP and systems. SIMPLE (standard teletext) consists of a num- ber of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern methods and easy selection of teletext information. allowing quick TEXT Switch on/off Press the TEXT button to switch to teletext. If TV and text picture displayed half and half of the again to display text picture fully. are press the TEXT button The initial page or last page appears on the screen. Two page numbers, TV station name, date and time on the tion, are screen, PR displayed headline. The first page number indicates your selecwhile the second shows the current page displayed. screen Press the TEXT button to switch off teletext. The mode previous reappears. PR SIMPLE text Page 1. 2. 123 selection 456 Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then reenter the correct page number. The D / E button can be used to select the lowing preceding or a 9 0 fol- page. Programming 78 MODE M colour button in LIST mode If the TV is in SIMPLE text, TOP text M button to switch to LIST mode. or FASTEXT mode, press the Four teletext page numbers of your choice can be colour coded and easily selected by pressing the corresponding coloured button on the remote control handset. 1. Press a 2. Using the NUMBER 3. 4. coloured button. buttons, select the page you wish to pro- gramme. Press the OK button. The selected page is stored as the selected page number, blinking once to confirm this. From now on, you can select this page with the same coloured button. The three other coloured buttons are programmed in this way. 33 Teletext TOP text The user (option) (option) guide displays the bottom of the four fields-red, green, yellow and blue field denotes the next group and the blue field indicates the next block. screen. The at yellow Block / group / page selection 1. With the blue button you can progress from block to block. 2. Use the yellow button to proceed to the next group with automatic overflow to the next block. 3. TEXT With the green button you can proceed to the next page with automatic overflow to the next group. the D button Alternatively 4. The red button permits the E Alternatively can can to existing be used. return to previous selection. be used. PR Direct page selection Corresponding to the SIMPLE teletext mode, you can select a page by entering it as a three digit number using the NUMBER buttons in TOP mode. FASTEXT PR 123 456 78 0 9 The teletext pages are colour coded along the bottom of the screen and are selected by pressing the corresponding coloured button. Page selection 1. Press the 2. You can button to select the index page. select the pages which are colour coded i tom line with the INDEX 3. same along the bot- coloured buttons. Corresponding to the SIMPLE page by entering its three digit teletext mode, you can select a page number with the NUMBER buttons in FASTEXT mode. 4. The D / E button lowing 34 page. can be used to select the preceding or fol- Teletext Special (option) teletext functions REVEAL Press this button to display concealed information, such as solutions of riddles or puzzles. Press this button again to remove the information from the display. SIZE Selects double Press this Press this height text. button to enlarge the top button again to enlarge page. Press this button again half of the page. the bottom half of the to return to the normal TEXT display. UPDATE Displays the TV picture on the screen while waiting for the new teletext page. The display will appear at the top left hand corner of the screen. When the updated page is available then will change to the page number. display Press this button to view the updated teletext page. PR HOLD the automatic page change which will occur if a teletext page consists of 2 or more sub pages. The number of sub pages and the sub page displayed is, usually, shown Stops on the screen below the time. When this button is the stop symbol the screen is displayed at the top left-hand pressed corner of and the automatic page change is inhibited. To continue press this button again. PR 123 456 78 9 0 MIX Displays the teletext pages superimposed on the TV pic- ture. To switch the TV INDEX off press this button again. Note : When TV and text picture are displayed half and half of the screen, MIX function is not available. picture TIME This button has two functions: a) When viewing play the time at TV programme, press this button to disthe top right hand corner of the screen. a Press this button again to remove the display. b) In teletext mode, press this button to select sub page at the bottom a number. The sub page number is displayed of the screen. To hold or change the sub page, press the RED/ GREEN D / E or NUMBER buttons. Press this button again to exit this function. 35 Connection of PC PC in socket COMPONENT INPUT 2 480i/480p/ 576i/576p/ 720p/1080i AV1 AV2 AV3 INPUT 1 480i/480p/ 576i/576p/ 720p/1080i PC/DTV Y (SXGA/ 480p/ 576p/ 720p/ 1080i) PB PR U P P G O R R A T D 1. RGB INPUT Connect the signal cable from the monitor PERSONAL COMPUTER to the PC 2. output socket of the socket of the set. input Connect the audio cable from the PC to the RGB/DVI INPUT (L) AUDIO (L) AUDIO sockets AUDIO (R) (R) E on the back of the set. DVI / RGB INPUT HDMI/DVI INPUT 3. Press the TV/AV MULTIMEDIA button to select RGB or or HDMI. 4. Switch on The set Note a. PERSONAL COMPUTER the can PC, and the PC be operated as screen appears the PC monitor. the set. : Connect PC to the PC input sockets of the set after changing the resolution of PC. b. If you want to watch the PC monitor the POWER button only, of the PC isn't Displayable MODE EGA VGA SVGA XGA switch off the set with the remote control handset. on switch off the set with the ON/OFF button on the set, the (If you screen displayed.) Monitor Specification Resolution 640X350 640X480 800X600 1024X768 (Synchronization input 36 on form : Horizontal Vertical Frequency (KHz) Frequency (Hz) 37.9 85 31.5 60 37.9 72 37.5 75 43.3 85 35.1 56 37.9 60 48.1 72 46.9 75 53.7 85 48.4 60 56.5 70 60.0 75 68.7 85 separate) Connection of external You connect additional can such equipment, as equipment VCRs, camcorders etc. to your set. Here shown may be somewhat different from your set. COMPONENT INPUT 2 480i/480p/ 576i/576p/ 720p/1080i AV1 AV2 AV3 INPUT 1 480i/480p/ 576i/576p/ 720p/1080i PC/DTV Y (SXGA/ 480p/ 576p/ 720p/ 1080i) PB PR RGB INPUT U P P Aerial socket (L) GO R R AUDIO A T D (R) (L) AUDIO (R) E DVI / RGB INPUT HDMI/DVI INPUT 1. Connect the RF out socket of the VCR to the aerial socket on the back of the set. 2. Connect the aerial cable to the RF aerial in socket of the VCR. 3. Store the VCR channel on a Press the PLAY button on 4. 5. VCR desired programme number using the 'Manual programme tuning' section. Select the programme number where the VCR channel is stored. the VCR. Euro scart sockets 1. Connect the Euro scart socket of the VCR to the Euro scart socket1,2or3oftheset. 2. Press the PLAY button If your VCR on COMPONENT INPUT the VCR. AV1 AV2 AV3 connect to Euro scart outputs switching voltage socket1,2or3,the setwillswitchtoAV1,AV2,SAV2orAV3 mode a But if you want to press the D / E button. automatically. mode, Otherwise press the TV/AV button setto on keep on watching TV appears on You also record programmes received can INPUT 1 480i/480p/ 576i/576p/ 720p/1080i PC/DTV Y (SXGA/ 480p/ 576p/ 720p/ 1080i) PB PR RGB INPUT U P P G O R R A T (L) AUDIO (L) AUDIO (R) D (R) E DVI / RGB INPUT HDMI/DVI INPUT the remote control hand- selectAV1,AV2,SAV2orAV3.TheVCRplaybackpicture the 2 480i/480p/ 576i/576p/ 720p/1080i VCR screen. by the TV on video tape. Note a. : i.e. the signals red, green and blue can only be selected for the Euro scart socket 1. These signals are transmitted, for example, by a pay TV decoder, game machine Signal type RGB, or b. c. d. photo CD unit, (R) If both Euro scart 1, 2 and 3 sockets have been connected to the VCRs simultaneously, only the AV 2 can be received. If the S-VIDEO(Y/C) signal is received through the Euro scart socket 2, you must change to the S-Video2 mode. If you use a RCA to Scart adaptor (not supplied), when both VIDEO IN and Y/C IN(S-VIDEO) sockets have been connected to the adaptor, the picture of the set can be unstable. Audio/Video 1. etc. input sockets AUDIO (L)/ MONO VIDEO S-VIDEO AV4 INPUT VCR (option) Connect the audio/video out sockets of the VCR to audio/video in sockets of the set. 2. PresstheTV/AVbuttontoselectAV1,AV2,SAV2,AV3orAV4. 3. Press the PLAY button The VCR on playback picture the VCR. appears on the screen. If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO socket of the set. Note : 37 Connection of external equipment S-Video / Audio input When VCR to the S-VIDEO sockets (option) COMPONENT INPUT 2 480i/480p/ 576i/576p/ 720p/1080i AV1 AV2 AV3 INPUT 1 480i/480p/ 576i/576p/ 720p/1080i PC/DTV Y (SXGA/ 480p/ 576p/ 720p/ 1080i) PB connecting PR RGB INPUT U P P G O R R A (L) (L) AUDIO T AUDIO (R) D (R) E quality an will be further socket, the picture improved. DVI / RGB INPUT HDMI/DVI INPUT 1. Connect the S-video socket of the VCR to the S-VIDEO socket of the set. 2. VCR Connect the audio cable from the VCR to the AUDIO sockets of the AV4 INPUT. 3. Select AV4 4. Press the PLAY button The VCR (R) AUDIO by pressing the TV/AV button on playback picture repeatedly. the VCR. appears on the screen. (L)/ MONO VIDEO Note S-VIDEO If both S-VIDEO and VIDEO sockets have been connected : to the VCR AV4 INPUT DVD VCR 1. simultaneously, only input the S-VIDEO can be received. sockets Connect the DVD output sockets (Y Cb Cr, Y Pb Pr, Y B-Y R-Y or Y PB PR) of the DVD to the DTV/DVD sockets (Y PB PR) of the set. 2. Connect the audio cable from the DVD to COMPONENT sockets of the set. 3. Press COMPONENT INPUT INPUT 2 480i/480p/ 576i/576p/ 720p/1080i AV1 AV2 AV3 1 480i/480p/ 576i/576p/ 720p/1080i PC/DTV Y (SXGA/ 480p/ 576p/ 720p/ 1080i) PB PR RGB INPUT U P P (L) G O R R A L) AUDIO T AUDIO (R) D (R) E DVI / RGB INPUT 4. HDMI/DVI INPUT the TV/AV or MULTIMEDIA Component 1 or Component 2. Press the PLAY button on the DVD. The DVD playback picture appears on the button to select screen. DVD DTV 1. input sockets Connect the SET TOP of the set. 480i/480p/ 576i/576p/ 720p/1080i AV1 AV2 AV3 INPUT 1 480i/480p/ 576i/576p/ 720p/1080i PC/DTV Y (SXGA/ 480p/ 576p/ 720p/ 1080i) PB PR RGB INPUT U P P G O R R A T (L) (L) AUDIO AUDIO 2. (R) D (R) E to the DTV/DVD sockets DVI / RGB INPUT HDMI/DVI INPUT 3. connect the SET TOP with the D-Sub Box COMPONENT INPUT 2 480i/480p/ 576i/576p/ 720p/1080i AV1 AV2 AV3 PC/DTV INPUT 1 480i/480p/ 576i/576p/ 720p/1080i Y (SXGA/ 480p/ 576p/ 720p/ 1080i) PB PR U RGB INPUT P P GO (L) R R AUDIO A T D (R) (L) AUDIO (R) E DVI / RGB INPUT HDMI/DVI INPUT SET TOP 38 Box PB PR) output Connect the audio cable from the SET TOP to the DTV/DVD AUDIO sockets of the set. Press the TV/AV or MULTIMEDIA button to select Component 1, Component 2, RGB SET TOP (Y socket to RGB INPUT socket on the set and audio cable of the HD-SET TOP to the AUDIO sockets of RGB/DVI INPUT.) COMPONENT INPUT 2 (or, inputs or HDMI. - - HDMITM, the HDMI logo and High-Definition Multimedia Interface trademarks of HDMI Licensing. This set can receive the High-Definition Multimedia Interface are (HDMI) trademarks or Input of or registered Digital Visual Interface(DVI). - This set supports HDCP (High-bandwidth Digital Contents Protection) Protocol for the 720p, 1080i) - - modes. set (480p, When you connect to HDMI/DVI Source devices (DVD Player, STB or PC) that support AUTO HDMI/DVI Plug & Play, this sets the HDMI/DVI source devices automatically. After reading HDMI/DVI source devices, using Display Data Channel (DDC) Protocol, Extended Display Identification Data (EDID) stored in the set is used. If HDMI/DVI Source devices do not support AUTO HDMI/DVI, the resolution is set manually. When Source Devices have DVI Output Connector, you must connect audio with separated cable. (Refer to <How to connect>) How to connect 1. When Source Devices (DVD Player or Set Top Box) support HDMI. If Source Devices have HDMI Output Connector, Source Devices connect to the set with HDMI Cable .(not supplied with the product). If Source Devices support Auto HDMI, automatically, Source Devices divert output resolution in 1280 x 720p. But if not, refer to the reference Manual of Source Devices and select resolution - - manually. - - To get the best picture quality, adjust the DVD Player 720p. Because HDMI sends Digital Video and Audio with Cable when using a HDMI Cable. or one Set Top Box output resolution cable, there is no need for a to 1280 special x Audio 2. When Source Devices (DVD Player or Set Top Box) supports DVI. If Source Devices have DVI Output Connector, Source Devices connect to the set with HDMI to DVI Cable (not supplied with the product). If Source Devices support Auto DVI, automatically, Source Devices divert output resolution in 1280 x 720p. But if not, refer to the reference Manual of Source Devices and select resolution manually. To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x - - - 720p. - In this case, use another cable for audio. When Source Devices have Analog Audio Output Connector, RGB/DVI Audio Input of the set connect to Audio Cable (not supplied with the product). And then you can listen to normal Audio. 3. When PC supports DVI. If PC have DVI Output Connector, Source Devices connect to the set with HDMI to DVI Cable supplied with the - (not product). - - - - - To get the best picture quality, adjust the PC graphics card to 1024 x 768, 60Hz. Use the the set's HDMI/DVI (VIDEO) for video connections, depending on your PC connector. If the graphics card on the PC does not output analog RGB and DVI simultaneously, connect only one of either RGB Input or HDMI/DVI Input to display the PC on the set. If he graphics card on the PC does output analog RGB and DVI simultaneously, the set to either RGB Input or HDMI/DVI Input; (the other mode is set to Plug and Play automatically by the set.) Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required. - In this case, another cable for audio. When PC (or sound card of PC) have Analog Audio Output Connector, RGB/DVI Audio Input of the set connect to Analog Audio Cable (not supplied with the product). And then you can listen to normal Audio. use 39 Reference Cable sample HDMI Cable (not supplied with the product) HDMI to DVI Cable (not supplied with the product) Analog Audio (not supplied Cable with (RCA type) the product) Analog Audio Cable (Stereo to RCA type) (not supplied with the product) How to use 1. Connect the HDMI/DVI Source Devices(DVD Player or Set Top Box or PC) and the set. 2. Turn on the display by pressing the POWER button on the set and HDMI/DVI Source Devices remote control. 3. Select HDMI/DVI Input source in Main Input option of PIP/DW menu. 4. Check the image on your set. There may be noise associated with the resolution, vertical pattern, contrast or brightness in HDMI/DVI Source Devices. If noise is present, change the HDMI/DVI Source Devices to another resolution, change the refresh rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can not changed, change the PC graphics card or consult the manufacturer of the PC graphics card. Notes: - - - - - Depending on the graphics card, DOS mode may not work if you use a HDMI to DVI Cable. Avoid keeping a fixed image on the set screen for a long period of time. The fixed image may become permanently imprinted on the screen. Use the Orbiter screen saver when possible. When Source Devices are connected with HDMI/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position and Size may not fit to Screen. As shown on page 26, press the MENU button to adjust the screen Position of the set and contact an PC graphics card service centre. When Source Devices connected HDMI/DVI Input output the set Resolution(480p, 720p, 1080i), the set Display fit EIA/CEA-861-B Specification to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your service centre. In case HDMI/DVI Source Devices Cable is not connected or poor cable connection, "No Signal" OSD display will appear. And in case of Video Resolution not being supported by the set output in HDMI/DVI Source Devices, "No Signal" OSD display will appear. Refer to the Manual of HDMI/DVI Source Devices or contact your service centre. 40 Note 41 Note 42 Troubleshooting check list Symptoms No picture, no Sound sound OK, poor picture Picture OK, poor sound Picture blurred Lines or streaks in Poor picture reception on some channels No colour Poor colour Remote control does not work Poor brightness Strange sound from inside the monitor Check these items and try to adjust these The mains plug-(plugged in and switched on) Is the TV switched on? Try another channel (weak signal) Check aerial (plugged into Check aerial (broken lead?) TV?) Check aerial Check for local interference Adjust contrast Adjust brightness Adjust colour Adjust volume Check the batteries in remote control Check Audio/Video sockets Contact LG service A (VCR only) provider(s) in ambient humidity or temperature may result in an unusual noise at the time of switching off or on of the monitor and does not indicate a fault with the monitor change 43 GUARANTEE LG Electronics U.K. Ltd. will provide the following services in order to expedite this Guarantee. 1. 2. All faulty components charge for a period of which fail due to defective manufacture will be 12 months from the date of original replaced free of purchase. The dealer (or his service agent) who sold the product will be reimbursed for any labour provided in the repair of this LG equipment, for a period of 12 months from the original date of purchase. These claims must be made in accordance with the published scale of service charges and relevant claims procedure. PLEASE NOTE: A. B. The dealer may restrict the guarantee to the original purchaser. The dealer is not obliged to carry out service under guarantee if unauthorized modifications apparatus, or if non standard components are used or if the serial number of the apparatus is removed, defaced, misused, or altered. C. Any claims made under guarantee must be directed to the dealer from whom the are originally purchased. The dealer may, before carrying out service under guarantee, require a receipted account as evidence of the date of purchase. We respectfully point out that your dealer is not obligated to replace batteries if they equipment D. made to the was become exhausted E. Aerial This alignment or worn and guarantee does in use. consumer control not affect your adjustments are not covered this by guarantee. statutory rights. REQUIREMENTS TO MAINTAIN WARRANTY COVERAGE: RETAIN YOUR RECEIPT TO PROVE DATE OF PURCHASE. A COPY OF YOUR RECEIPT MUST BE SURRENDERED AT THE TIME GUARANTEE SERVICE IS PROVED. Product Registration Card: It is helpful to complete at least your name, address, phone, model & serial numbers and return it. This will enable LG to assist you in receipt, the future should you your units be stolen, lose your or should modifications be necessary. To obtain information or assistance: Call 0870 607 5544 Monday-Friday 9.00am-4.30pm. Service website: http://lgelectronics.co.uk MODEL NO.* * Please complete for your SERIAL NO.* own record DATE OF PURCHASE *
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement