Samsung DVD-R149 Instruction manual

Instruction Manual
DVD-R149
www.samsung.com/uk
AK68-01403A
01403A-R149-XEU-ENG.indb 1
2007-03-09 오후 11:10:27
Getting Started
Getting Started
Warning
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
IMPORTANT NOTE
The mains lead on this equipment is supplied with a moulded
plug incorporating a fuse. The value of the fuse is indicated
on the pin face of the plug. If it requires replacing, a fuse
approved to BS1362 of the same rating must be used.
Never use the plug with the fuse cover omitted if the cover is
detachable. If a replacement fuse cover is required, it must be
of the same colour as the pin face of the plug.
Replacement covers are available from your dealer.
This symbol indicates “dangerous voltage” inside
the product that presents a risk of electric shock
or personal injury.
This symbol indicates important instructions
accompanying the product.
If the fitted plug is not suitable for the power points in your
house or the cable is not long enough to reach a power point,
you should obtain a suitable safety approved extension lead
or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug,
remove the fuse and then safely dispose of the plug.
Do not connect the plug to a mains jack, as there is a risk of
shock hazard from the bared flexible cord.
To disconnect the apparatus from the mains, the plug must
be pulled out from the mains socket, therefore the mains plug
shall be readily operable.
Do not install this equipment in a confined space such as a
bookcase or similar unit.
WARNING : To prevent damage which may result in fire
or electric shock hazard, do not expose this
appliance to rain or moisture.
CAUTION : DVD RECORDER USES AN INVISIBLE LASER BEAM
WHICH CAN CAUSE HAZARDOUS RADIATION
EXPOSURE IF DIRECTED.
BE SURE TO OPERATE RECORDER CORRECTLY AS
INSTRUCTED.
CAUTION
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO
NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
The product unit accompanying this user manual is licensed
under certain intellectual property rights of certain third
parties. This license is limited to private non-commercial use
by end-user consumers for licensed contents.
No rights are granted for commercial use.
The license does not cover any product unit other than
this product unit and the license does not extend to any
unlicensed product unit or process conforming to ISO/IEC
11172-3 or ISO/IEC 13818-3 used or sold in combination
with this product unit. The license only covers the use of this
product unit to encode and/or decode audio files conforming
to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are
granted under this license for product features or functions
that do not conform to the ISO/IEC 11172-3 or ISO/IEC
13818-3.
This product satisfies CE regulations when shielded cables and
connectors are used to connect the unit to other equipment.
To prevent electromagnetic interference with electric
appliances, such as radios and televisions, use shielded cables
and connectors for connections.
CAUTION
• Apparatus shall not be exposed to dripping or splashing and
no objects filled with liquids, such as vases, shall be placed
on the apparatus.
• The Mains plug is used as a disconnect device and shall stay
readily operable at any time.
English - 2
01403A-R149-XEU-ENG.indb 2
2007-03-09 오후 11:10:51
▌Important Safety Instructions
Read these operating instructions carefully before using the
DVD Recorder. Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, Install in accordance
with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding- type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. if the provided
plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, the point
where they exit from the apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
▌Handling Cautions
• Before connecting other components to this DVD Recorder,
be sure to turn them all off.
• Do not move the DVD Recorder while a disc is being played,
or the disc may be scratched or broken, the DVD Recorder's
internal parts may be damaged.
• Do not put a flower vase filled with water or any small metal
objects on the DVD Recorder.
• Be careful not to put your hand into the disc tray.
• Do not place anything other than the disc in the disc tray.
• Exterior interference such as lightning and static
electricity can affect normal operation of this DVD Recorder.
If this occurs, turn the DVD Recorder off and on again with
the STANDBY/ON button, or disconnect and then reconnect
the AC power cord to the AC power outlet.
The DVD Recorder will operate normally.
• Be sure to remove the disc and turn off the DVD Recorder
after use.
▌Maintenance of Cabinet
Getting Started
• Disconnect the AC power cord from the AC outlet when you
don’t intend to use the DVD Recorder for long periods of
time.
• Clean the disc by wiping in a straight line from the inside to
the outside of the disc.
Precaution
For safety reasons, be sure to disconnect the AC power cord
from the AC outlet.
• Do not use benzene, thinner, or other solvents for cleaning.
• Wipe the cabinet with a soft cloth.
▌Disc Handling
• Use discs with regular shapes.
If an irregular disc (a disc with a
special shape) is used, this DVD
recorder may be damaged.
Holding discs
• Avoid touching the surface of a disc where
recording is performed.
DVD-RAM, DVD-RW and DVD-R
• Clean with an optional DVD-RAM/PD disc
cleaner (LF-K200DCA1 where available).
Do not use cleaners or cloths for CDs to
clean DVD-RAM/DVD-RW/DVD-R discs.
DVD-Video, Audio CD
• Wipe off dirt or contamination on the disc with a soft cloth.
Cautions on handling discs
• Do not write on the printed side with a ball-point pen or
pencil.
• Do not use record cleaning sprays or antistatic.
Also, do not use volatile chemicals, such as benzene or
thinner.
• Do not apply labels or stickers to discs. (Do not use discs
fixed with exposed tape adhesive or leftover peeled-off
stickers.)
• Do not use scratch-proof protectors or covers.
• Do not use discs printed with label printers available on the
market.
• Do not load warped or cracked discs.
English - 3
01403A-R149-XEU-ENG.indb 3
2007-03-09 오후 11:10:53
Getting Started
▌Disc Storage
Be careful not to harm the disc because the data on these
discs is highly vulnerable to the environment.
• Do not keep under direct sunlight.
• Keep in a cool ventilated area.
• Store vertically.
• Keep in a clean protection jacket.
• If you move your DVD recorder suddenly from a cold place to
a warm place, condensation may generate on the operating
parts and lens and cause abnormal disc playback. If this
occurs, do not connect the plug to the power outlet and wait
for two hours. Then insert the disc and try to play back again.
Using CD-R/-RW
• Use a 700MB(80 minutes) CD-R/-RW disc. If possible, do not
use a 800MB(90 minutes) or above disc, as the disc may not
play back.
• If the CD-R/-RW disc was not recorded as a closed session,
you may experience a delay in the early playback time, all
recorded files may not play.
• Some CD-R/-RW discs may not be playable with this DVD
Recorder, depending on the device which was used to burn
them. For contents recorded on CD-R/-RW media from CDs
for your personal use, playability may vary depending on
contents and discs.
DVD-R Disc Playback
▌Disc Specifications
This unit allows you to record and playback high quality
digital images on DVD-RAM/DVD-RW/DVD-R discs.
You can record and edit digital images on DVD-RAM/
DVD-RW/DVD-R discs.
(DVD+RW/DVD+R discs can be played, but cannot be
recorded.)
DVD-Video
• A digital versatile disc (DVD) can contain up to 135-minutes
of images, 8 audio languages and 32 subtitle languages. It
is equipped with MPEG-2 picture compression and Dolby
digital surrounding, allowing you to enjoy vivid and clear
theatre quality images in the comfort of your own home.
• When switching from the first layer to the second layer of
a dual-layered DVD Video disc, there may be momentary
distortion in the image and sound. This is not a malfunction
of the DVD Recorder.
• Once a DVD-R/DVD-RW(V) recorded in Video Mode is
finalised, it becomes DVD-Video.
Audio CD
• An audio disc on which 44.1kHz PCM Audio is recorded.
• Plays CD-DA format audio CD-R and CD-RW discs. The DVD
Recorder may not be able to play some CD-R or CD-RW discs
due to the condition of the recording.
CD-R/-RW
MP3 CD-R/-RW
• Only CD-R discs with MP3 files recorded with ISO9660 or
JOLIET format can be played back.
• Only MP3 files with the ".mp3", ".MP3" extension can be used.
• For MP3 files recorded with a VBR(Variable Bit Rates), from 32
Kbps to 320 Kbps, the sound may cut in out.
• Playable bitrate range is from 56Kbps to 320Kbps.
• This DVD Recorder can handle a maximum of 500 files and 100 folders.
• DVD-RAM/DVD±RW/DVD±R disc recorded with MP3 files can
be played back.
JPEG CD-R/-RW
• Only JPEG files with the ".jpg", ".JPG" extension can be used.
• This DVD Recorder can handle a maximum of 500 files and
100 folders.
• Maximum size of progressive JPEG is 3M pixels.
• MOTION JPEG is not supported.
• DVD-RAM/±RW/±R discs that contain JPEG files can be
played back.
• Once a DVD-R recorded in Video Mode is finalised, it
becomes DVD-Video.
• You can record onto the available space on the disc and
perform editing functions such as giving titles to discs and
programmes and erasing programmes before finalising.
• When programming is erased from a DVD-R, that space does
not become available. Once an area on a DVD-R is recorded
on, that area is no longer available for recording, whether the
recording is erased or not.
• It takes about 30 seconds for the DVD Recorder to complete
recording management information after recording finishes.
• This DVD Recorder optimizes the DVD-R for each recording.
Optimizing is carried out when you start recording after
inserting the disc or turning on the DVD Recorder. Recording
onto the disc may become impossible if optimizing is carried
out too many times.
• Playback may be impossible in some cases due to the
condition of recording.
• This DVD Recorder can play back DVD-R discs recorded and
finalised with a Samsung DVD video recorder. It may not be
able to play some DVD-R discs depending on the disc and
the condition of the recording.
DVD-RW Disc Playback and Recording
• Recording and playback can be performed on DVD-RW discs
in both the Video and VR Modes.
• Once a DVD-RW recorded in both the Video and VR Modes
is finalised, you cannot perform addtional recording.
• Once a DVD-RW recorded in Video Mode is finalised, it
becomes DVD-Video.
• In both modes, playback can be performed before and after
finalisation, but additional recording, deleting and editing
can not be performed after finalisation.
• If you want to record the disc in VR Mode and then record in
V Mode, be sure to execute Format.
Be careful when executing Format because all the recorded
data may be lost.
• A DVD-RW blank disc is initialised to VR Mode when first
initialised.
• DVD-RW (VR mode)
- This is a format that is used for recording data on a DVD-RW
disc. You can record multiple titles, edit, delete, partial delete,
create a playlist, etc.
- A disc that is recorded in this mode may not be played by
existing DVD Recorder.
English - 4
01403A-R149-XEU-ENG.indb 4
2007-03-09 오후 11:10:54
DVD-RAM Disc Playback and Recording
• For cartridge type DVD-RAM discs, remove the cartridge and
use the disc only.
• Ensure that the recording mode is set to VR mode. Otherwise,
this product will not be able to play the recording.
• You cannot play a DVD-RAM in most DVD players due to
compatibility issues.
• Only DVD-RAM standard Version 2.0 discs can be played in
this unit.
• DVD-RAM recorded on this unit may not work with other
DVD Players. To determine compatibility with these DVDRAM discs, refer to the user’s manual for the player.
Do not use the following discs!
• LD, CD-G, CD-I, Video-CD, CD-ROM, DVD-ROM and MPEG4
discs should not be used in this DVD Recorder.
[Note]
Disc types that can be played : CD/CD-R/CD-RW/MP3/JPEG/
DVD-Video/DVD-RAM/DVD±RW/DVD±R.
For a DVD-RW(V mode)/DVD±R disc, which has been recorded
on another component, it can play only when finalised.
• Some commercial discs and DVD discs purchased outside
your region may not be playable with this DVD Recorder.
When these discs are played, either “No Disc” or "The disc
cannot be played. Please check the regional code of the disc."
will be displayed.
• If your DVD-RAM/DVD-RW/DVD-R disc is an illegal copy or is
not in DVD video format, it may also not be playable.
Getting Started
• DVD-RW (Video mode)
- This is a format that is used for recording data on a DVD-RW
or DVD-R disc. The disc can be played by existing DVD
Recorder once it has been finalised.
- If a disc that has been recorded in Video Mode by a different
maker’s recorder but has not been finalised, it cannot be
played or additionally be recorded by this DVD Recorder.
Disc Compatibility
• Not all brands of discs will be compatible with this DVD
Recorder.
COPY PROTECTION
• Many DVD discs are encoded with copy protection.
Because of this, you should only connect your DVD
recorder directly to your TV, not to a VCR.
Connecting to a VCR results in a distorted picture from
copy-protected DVD discs.
• This DVD Recorder incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology
must be authorised by Macrovision Corporation, is
intended for home and other limited viewing uses only
unless otherwise authorised by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Protection
This DVD Recorder can allow you to protect the contents of
your discs, as described below.
• Programme-protected : See page 51 “Locking(Protecting) a
Title”
• Disc-protected : See page 58 “Disc Protection”
❊ DVD-RAM/DVD-RW/DVD-R discs that are incompatible with
the DVD-VIDEO format cannot be played with this DVD
Recorder.
❊ For more information on DVD recording compatibility,
consult your DVD-RAM/DVD-RW/DVD-R manufacturer.
❊ Use of poor quality DVD-RAM/DVD-RW/DVD-R discs may
cause following unexpected problems including, without
limitation, recording failure, loss of recorded or edited
materials or damage to the DVD Recorder.
English - 5
01403A-R149-XEU-ENG.indb 5
2007-03-09 오후 11:10:55
Getting Started
Contents
■ Presetting Channels with the Manual Setup function ... 21
Getting Started
■ Warning ........................................................................................... 2
■ Precaution ...................................................................................... 3
Important Safety Instructions ................................................. 3
Handling Cautions ...................................................................... 3
Maintenance of Cabinet............................................................ 3
Disc Handling ................................................................................ 3
Disc Storage................................................................................... 4
Disc Specifications ...................................................................... 4
■ Contents .......................................................................................... 6
■ General Features .......................................................................... 8
■ Before reading the user’s manual .......................................... 9
■ How to use the DVD Recorder ................................................ 9
■ Unpacking ...................................................................................... 10
Accessories..................................................................................... 10
Preparing the Remote Control................................................ 10
■ Description..................................................................................... 12
Front Panel ..................................................................................... 12
Front Panel Display ..................................................................... 12
Rear Panel ....................................................................................... 13
Tour of the Remote Control ..................................................... 14
■ Setting up the Language Options ......................................... 22
■ Setting up the System Options............................................... 23
EP Mode Time Setting ................................................................ 23
Automatic Chapter Creation ................................................... 23
Quick Recording Setting ........................................................... 23
■ Setting up the Audio Options ................................................. 24
Digital Output ............................................................................... 24
DTS .................................................................................................... 24
Dynamic Compression .............................................................. 25
NICAM .............................................................................................. 25
■ Setting up Video Options.......................................................... 25
TV Aspect........................................................................................ 25
3D Noise Reduction (motion adaptive noise reduction) .... 25
Video output ................................................................................. 26
Progressive scan........................................................................... 26
■ Setting up the Parental Control .............................................. 27
About the Rating Level .............................................................. 27
About the Change Password ................................................... 27
Recording
■ Recordable discs .......................................................................... 28
Compatibility between Samsung and Other Company’s
Recorder...........................................................................................28
Connecting & Setting Up
■ Connecting the DVD Recorder ............................................... 15
■ Additional connections ............................................................. 15
■ Other type of connecting the Video output cable .......... 16
Case 1 : Connecting to a Video(Composite) output jack.... 16
Case 2 : Connecting to an S-Videooutput jack.................. 17
Case 3 : Component Video output jacks ............................. 17
■ Other type of connecting the Audio output cable.......... 18
Case 1 : Connecting to your TV............................................... 18
Case 2 : Connecting to a stereoamplifier with AV output
jacks ...................................................................................................18
Case 3 : Connecting to an AVamplifier with a digital
output jack ......................................................................................18
■ Recording Formats ...................................................................... 29
DVD-RW(Video mode)/-R ......................................................... 29
DVD-RAM/-RW(VR mode)......................................................... 29
■ Recording Mode........................................................................... 30
■ Unrecordable video .................................................................... 30
About INFO Button ..................................................................... 31
■ Recording immediately ............................................................. 32
Recording the current TV programme you are watching ..... 32
Recording from external equipment you are watching...... 32
■ Making a One Touch Recording (OTR) ................................. 33
■ Making a Timer Recording........................................................ 34
■ Editing the Scheduled Record List......................................... 35
■ Deleting the Scheduled Record List...................................... 36
■ Using the Video Plus+Feature ................................................. 36
■ Video Plus+ Extended ................................................................ 37
System Setup
■ EZ REC MODE ................................................................................ 37
■ On-Screen Menu Navigation ................................................... 19
■ Plug & Auto Setup ....................................................................... 19
■ Setting the Clock.......................................................................... 20
■ Presetting Channels with the Auto Setup function ........ 20
English - 6
01403A-R149-XEU-ENG.indb 6
2007-03-09 오후 11:10:56
Editing
■ Region code (DVD-Video only) ............................................... 38
■ Basic Editing (Title List) .............................................................. 50
Renaming(Labeling) a Title ...................................................... 50
Locking (Protecting) a Title ...................................................... 51
Deleting a Title.............................................................................. 51
Deleting a Section of a Title ..................................................... 52
■ Logos of Discs that can be played ......................................... 38
■ Disc types that can be played ................................................. 38
Discs that cannot be played .................................................... 39
■ Playing a Disc ................................................................................ 39
Using the Disc Menu & Title Menu ........................................ 40
Using the playback related buttons ..................................... 40
■ Slow Motion play/Step Motion Play ..................................... 41
Slow Motion Play ......................................................................... 41
Step Motion Play.......................................................................... 41
■ Using the ANYKEY button ........................................................ 42
Moving to a desired scene directly ....................................... 42
■ Repeat Play..................................................................................... 42
Playing Repeatedly ..................................................................... 42
Playing a Certain section Repeatedly................................... 42
■ Selecting the Subtitle Language............................................ 43
■ Selecting the Audio Language ............................................... 43
■ Changing the Camera Angle ................................................... 43
Getting Started
Playback
■ Advanced Editing (Playlist)....................................................... 53
Creating a Playlist ........................................................................ 53
Playing Entries in the Playlist................................................... 53
Renaming a Playlist Entry ......................................................... 54
Editing a Scene for the Playlist................................................ 54
Copying a Playlist Entry to the Playlist ................................. 57
Deleting a Playlist Entry from the Playlist ........................... 57
■ Disc Manager................................................................................. 57
Editing the Disc Name ............................................................... 57
Disc Protection ............................................................................. 58
Formatting a Disc ........................................................................ 58
Finalising a disc ............................................................................ 59
Unfinalising a disc (V/VR mode) ............................................. 59
Delete All Title Lists ..................................................................... 60
■ Zooming-In .................................................................................... 44
■ Using Bookmarks ......................................................................... 44
Setting Bookmarks ...................................................................... 44
Playing back a bookmark ......................................................... 44
Clearing a bookmark .................................................................. 45
■ Using the Markers........................................................................ 45
Setting Markers ............................................................................ 45
Playing back a Marker ................................................................ 45
Clearing a Marker ........................................................................ 45
Additional Information
■ Troubleshooting........................................................................... 61
■ Specifications ................................................................................ 63
■ Warranty.......................................................................................... 64
■ Playing back an Audio CD(CD-DA)/MP3.............................. 46
Buttons on the Remote Control used for Audio CD (CDDA)/MP3 playback........................................................................46
Playing an Audio CD(CD-DA) .................................................. 46
Playing back an MP3 Disc ......................................................... 47
Repeat Playback of an Audio/MP3 Disc............................... 47
Play Option Mode........................................................................ 48
To Programme Tracks ................................................................. 48
■ Playing back a Picture Disc ....................................................... 48
■ Playing the Title List .................................................................... 49
Title List Screen Elements ......................................................... 49
English - 7
01403A-R149-XEU-ENG.indb 7
2007-03-09 오후 11:10:58
Getting Started
General Features
This unit allows you to record and playback high quality
digital images on DVD-RAM/DVD-RW/DVD-R discs.
A variety of functions with an easy-to-use user interface
High quality digital audio and video recording and
playback
The integrated menu system and the messaging function
allow you to perform desired operations both easily and
conveniently. With a DVD-RAM or DVD-RW(VR mode) disc,
you can edit recorded video, create a playlist, edit video in a
specific sequence according to your requirements.
You can record up to approximately 16-hours of video on a
double side 9.4 GB DVD-RAM disc,up to 15-hours on
a dual-layer 8.5GB DVD-R disc, and up to 8-hours on a 4.7GB
DVD-RAM/DVD-RW/DVD-R disc, depending on the recording
mode.
EZ REC MODE
This function allows you Initialise and Finalise a disc
automatically. (See page 37.)
Selectable Recording Mode
You can set your recorder to one of four different recording
speeds, each varying in recording quality and length. EP (6Hr
or 8Hr) mode yields the most recording time, LP & SP modes
provide less recording time with higher quality recording, XP
mode gives you the highest quality recording.
Automated Quality Adjustment for Timer Recording
If FR mode is selected, the video quality is adjusted
automatically so that all video for the scheduled time can
be recorded onto the free disc space. (See page 34.)
Creating a DVD video title using DVD-RW/DVD-R disc
With the DVD-Recorder, you can create your own DVD Video
titles on 4.7 GB DVD-RW/DVD-R or 8.5 GB DVD-R discs.
High quality progressive scan
Progressive scanning provides high resolution and flicker free
video. The 10-bit 54-MHz DAC and 2D Y/C Separating Circuitry
provides the highest image playback and recording quality.
(See pages 16, 26)
English - 8
01403A-R149-XEU-ENG.indb 8
2007-03-09 오후 11:10:59
How to use the DVD Recorder
Make sure to check the following terms before reading the
user’s manual.
Icons that will be used in manual
Icon
Term
Definition
DVD
This involves a function available
in DVD or DVD-R/DVD-RW(V) discs
that have been recorded and finalised.
RAM
This involves a function available in
DVD-RAM.
-RW
This involves a function available in
DVD-RW.
-R
This involves a function available in
DVD-R.
+RW
This involves a function available in
DVD+RW.
+R
This involves a function available in
DVD+R.
CD
This involves a function available in a
data CD (CD-R or CD-RW).
JPEG
This involves a function available in
a data picture CD-R/-RW or DVD-RAM/
DVD±RW/DVD±R discs.
MP3
This involves a function available in a
data CD-R/-RW or DVD-RAM/
DVD±RW/ DVD±Rdiscs.
Caution
NOTE
▌Step 1 : Select the disc type
This DVD Recorder can record on the following types of discs.
If you want to repeatedly record on the same disc or you want
to edit the disc after recording, select a rewritable DVD-RW or
DVD-RAM type disc.
If you want to save recording without any change, choose a
non-rewritable DVD-R.
▌Step 2 : Format the disc to start recording
The DVD Recorder automatically starts formatting when an
unused disc is inserted. This is required for the preparation of
recording on a disc.
This involves a case where a function
does not operate or settings may be
cancelled.
Using a DVD-RAM
This type of disc can be formatted in DVD-Video Recording
format (VR mode). You can edit recorded video and create
a playlist and edit video in a specific sequence according to
your requirements.
Using a DVD-RW
• When an unused DVD-RW disc is first inserted, the message
“Uninitialised Disc. Do you want to initialise this disc?” will
be displayed. If you select Yes, initialising will be start. DVDRW disc can be formatted in either DVD-Video format (Video
mode) or DVD-Video Recording format (VR mode)
Using a DVD-R
Formatting a disc is unnecessary and only Video Mode
Recording is supported. You can play this type of discs on
various DVD components only when they have been finalised.
■ You can only use either the VR or Video mode on a
DVD-RW, but not both at the same time.
This involves tips or instructions on
the page that help each function
operate.
■ You can change the DVD-RW format to another
format by reinitialising. It should be noted that the
disc's data will be lost when changing formats.
One-Touch A function that can be operated by
button using only one button.
ANYKEY
button
Getting Started
Before reading the user’s manual
A function that can be operated by
using ANYKEY button.
▌Step 3 : Recording
About the use of this user’s manual
1) Be sure to be familiar with Safety Instructions before using
this DVD Recorder. (See pages 2-5)
2) If a problem occurs, check for Troubleshooting.
(See pages 61-62.)
Copyright
©2007 Samsung Electronics Co.
All rights reserved; No part or whole of this user’s manual may
be reproduced or copied without the prior written permission
of Samsung Electronics Co.
There are two different recording methods, Direct Recording
and Timer Recording. Timer recording is classified as a Date :
Once, Daily, MO-SA, MO-FR, W-SA, etc.
Recording mode : XP (high quality mode), SP (standard quality
mode), LP (long recording mode), and EP (extended mode)
according to the recording mode. When recording is set in the
FR mode, the best quality picture is recorded with regards to
the remaining time on the disc.
English - 9
01403A-R149-XEU-ENG.indb 9
2007-03-09 오후 11:11:00
Getting Started
▌Step 4 : Playing
Unpacking
You can select the title you want to play in a displayed menu
and then immediately start playback.
A DVD consists of sections called titles, and sub sections called
chapters.
During recording, a title is created between two points
where you start and stop recording. Chapters will be created
automatically when you finalise recording on DVD-R / DVD-RW
discs in Video mode.
▌Accessories
Check for the supplied accessories below.
▌Step 5 : Editing a recorded disc
Video/Audio Cable
Editing on discs is easier than conventional video tapes. The
DVD Recorder supports many different edit functions, possible
only with DVDs. With a simple and easy edit menu, you can
operate various edit functions, such as delete, copy, rename,
lock, etc., on a recorded title.
Creating a playlist (DVD-RAM/DVD-RW in VR mode)
With this DVD Recorder, you can create a new playlist on the
same disc and edit it without the change of the original
recording.
Remote Control
RF Cable for TV
Batteries for Remote
Control (AAA Size)
▌Step 6 : Finalising & Playing on other DVD components
To play your DVD on other DVD components, finalising may
be necessary. First, finish all editing and recording operations,
then finalise the disc.
When using a DVD-RW disc in VR Mode
Although finalising is generally unnecessary when playing
the disc on a VR Mode compatible component, a finalised disc
should be used for playback.
When using a DVD-RW disc in Video Mode
The disc should be finalised first to enable playback on
anything other than this DVD Recorder. No more editing or
recording can be made on the disc once it has been finalised.
When using a DVD-R disc
You should finalise the disc to play it on a component other
than this DVD Recorder. You cannot edit or record on the disc
once it has been finalised.
■ You can finalise automatically using EZ REC MODE.
(see page 37)
Instruction Manual
Quick Guide
▌Preparing the Remote Control
Install Batteries in the Remote Control
• Open the battery cover on the back of the remote control.
• Insert two AAA batteries. Make sure that the polarities
(+ and -) are aligned correctly.
• Replace the battery cover.
If the remote does not operate properly:
• Check the polarity +/- of the batteries (Dry-Cell)
• Check if the batteries are drained.
• Check if remote sensor is blocked by obstacles.
• Check if there is any fluorescent lighting nearby.
Dispose of batteries according to local environmental
regulations. Do not put them in the household trash.
English - 10
01403A-R149-XEU-ENG.indb 10
2007-03-09 오후 11:11:02
To determine whether your television is compatible, follow the instructions below.
Controllable TV Codes
BRAND
BUTTON
BRAND
BUTTON
SAMSUNG
01, 02, 03, 04, 05, 06, 07, 08, 09
SALORA
74
AIWA
82
SANYO
41, 42, 43, 44, 48
ANAM
10, 11, 12, 13, 14, 15, 16, 17, 18
SCHNEIDER
06
BANG & OLUFSEN
57
SELECO
74
BLAUPUNKT
71
SHARP
36, 37, 38, 39, 48
BRANDT
73
SIEMENS
71
BRIONVEGA
57
SINGER
57
CGE
52
SINUDYNE
57
CONTINENTAL EDISON
75
SONY
35, 48
DAEWOO
19, 20, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34
TELEAVA
73
EMERSON
64
TELEFUNKEN
67, 73, 75, 76
FERGUSON
73
THOMSON
72, 73, 75
FINLUX
06, 49, 57
THOMSON ASIA
80, 81
FORMENTI
57
TOSHIBA
47, 48, 49, 50, 51, 52
FUJITSU
84
WEGA
57
GRADIENTE
70
YOKO
06
GRUNDIG
49, 52, 71
ZENITH
63
HITACHI
60, 72, 73, 75
IMPERIAL
52
JVC
61, 79
LG
06, 19, 20, 21, 22, 78
LOEWE
06, 69
LOEWE OPTA
06, 57
MAGNAVOX
40
METZ
57
MITSUBISHI
06, 48, 62, 65
MIVAR
52, 77
NEC
83
NEWSAN
68
NOBLEX
66
NOKIA
74
NORDMENDE
72, 73, 75
PANASONIC
53, 54, 74, 75
PHILIPS
06, 55, 56, 57
PHONOLA
06, 56, 57
PIONEER
58, 59, 73, 74
RADIOLA
06, 56
RADIOMARELLI
57
RCA
45, 46
REX
74
SABA
57, 72, 73, 74, 75
Getting Started
1. Switch your television on.
2. Point the remote control towards the television.
3. Press and hold the STANDBY/ON button and enter the two-figure code corresponding to the brand of your television, by
pressing the appropriate number buttons.
Result : If your television is compatible with the remote
control, it will switch off. It is now programmed to
operate with the remote control.
■ If several codes are indicated for your television
brand, try each one in turn until you find one that
works.
■ If you replace the remote control's batteries, you must
set the brand code again.
Then you can control the television using the
following buttons after the TV button.
Button
STANDBY/ON
INPUT SEL.
TV VOL (+ or -)
PROG ( or )
TV MUTE
0~9
Function
Used to switch the television on and off.
Used to select an external source.
Used to adjust the volume of the television.
Used to select the desired channel.
Used to toggle the sound on and off.
Used to input number directly.
■ The various functions will not necessarily work on all
televisions. If you encounter problems, operate the
television directly.
English - 11
01403A-R149-XEU-ENG.indb 11
2007-03-09 오후 11:11:04
Getting Started
Description
▌Front Panel
7. PROG (
)
Select TV preset Channels.
Same as PROG button on the remote control.
1. STANDBY/ON
Turns the DVD Recorder on and off.
2. AV3 IN
Connect external equipment.
8. REC
Starts recording.
3. DISC TRAY
Opens to accept a disc.
4. P.SCAN
Selects the progressive scan mode.
9. SEARCH/SKIP
Go to the next title/chapter/track or go back to the
previous title/chapter/track.
5. OPEN/CLOSE
Opens and closes the disc tray.
10. STOP
Stops disc playback.
6. DISPLAY
Displays the playing status, title/chapter/ time, etc.
11. PLAY/PAUSE
Plays a disc or pauses playback/recording.
▌Front Panel Display
1. Lights when a disc is loaded.
2. Lights in the record mode.
3. Lights to indicate the timer record mode.
4. Lights when a DVD-RAM/DVD±R/DVD±RW
disc is loaded.
5. Playing time/clock/current status indicator.
6. Lights in the progressive scan mode.
English - 12
01403A-R149-XEU-ENG.indb 12
2007-03-09 오후 11:11:05
Getting Started
▌Rear Panel
1.
In from aerial connector
2.
Out to TV connector
3. AV2(EXT) INPUT SCART Connector
4. AV1(TV) OUTPUT SCART Connector
5. DIGITAL AUDIO OUT(OPTICAL)
Connects to an amplifier having a digital optical
audio input jack.
6. DIGITAL AUDIO OUT(COAXIAL)
Connects to an amplifier having a digital coaxial
audio input jack.
7. AUDIO OUT
Connects to the audio input of external equipment
using audio cables.
8. VIDEO OUT
Connects the input of external equipment using a
Video cable.
9. S-VIDEO OUT
Connects the input of external equipment using
an S-Video cable.
10. COMPONENT VIDEO OUT
Connects to equipment having Component video
output.
■ The Antenna connection does not pass output signal
of DVD. To watch a DVD on your TV, you must connect
audio/video cables.
English - 13
01403A-R149-XEU-ENG.indb 13
2007-03-09 오후 11:11:06
Getting Started
▌Tour of the Remote Control
You can control certain functions of another manufacturer’s TV with this remote control.
Control function buttons involve: STANDBY/ON, PROG / , TV VOL +/-, Direct Number buttons, TV MUTE, INPUT SEL.
button.
9. TV MUTE Button
This operates as Sound Mute. (TV mode)
26
27
28
29
1
16
17
11. OK/DIRECTION(▲▼◄ ►) Buttons
4
5
6
7
8
9
10
12. TITLE LIST/DISC MENU Button
Use this to enter the View Recording list/Disc menu.
13. ANYKEY Button
Use this to view the status of the disc that is being played.
2
3
10. MENU Button
Brings up the DVD recorder’s setup menu.
18
19
14. REC Button
Use to make a recording on DVD-RAM/-RW/-R discs.
15. REC MODE Button
This will display the recording status.(XP/SP/LP/EP)
16. EZ REC MODE Button
17. OPEN/CLOSE Button
To open and close the disc tray.
20
18. AUDIO Button
Use this to access various audio functions on a disc.
(DVD mode)
21
19. Play/Pause Button
Press to play a disc or pause playback/recording.
20. PROG Buttons
Select preset channels in a specific order.
Same as PROG buttons in front panel.
11
21. RETURN Button
Returns to a previous menu.
12
13
14
15
22
23
24
25
22. PLAY LIST/TITLE MENU Button
Use this to return to the Title menu, or to view the
recorded files list.
23. EXIT Button
Exit the on-screen menu.
24. MARKER/TIMER Button
25. CANCEL Button
26. TV Button
Press this to operate TV.
27. DVD Button
Press this when you use a DVD recorder.
1. STANDBY/ON Button
2. 0~9(Number) Buttons
3. TV/DVD Button
4. Reverse/Forward Skip Buttons
Press to skip a disc backwards or forwards.
28. INPUT SEL. Button
Select line input signal in external input mode
(PROG, AV input)
29. INFO Button
This will display current settings or disc status.
5. Reverse/Forward Step Buttons
Press to play frame by frame.
6. Reverse/Forward Search Buttons
Press to search a disc backwards or forwards.
7. STOP Button
Press to stop a disc.
8. TV VOL Button
Volume adjustments.
English - 14
01403A-R149-XEU-ENG.indb 14
2007-03-09 오후 11:11:08
Connecting & Setting Up
Connecting the DVD Recorder
Additional connections
You can connect your DVD Recorder to a satellite or digital
tuner.
Connecting & Setting Up
This section involves various methods of connecting the
DVD Recorder to other external components and required
initial setting modes.
You can connect your DVD Recorder to the television using
the SCART cable (not supplied) if the appropriate input is
available on the television.
1. Connect the RF cable as shown.
2. Connect one end of the SCART cable to the AV1 socket on
the rear of the DVD Recorder.
3. Plug the other end into the appropriate connector on the
television.
external device
(VCR/Satellite receiver)
4. Plug in the DVD Recorder and TV.
5. Turn on the DVD Recorder and TV.
6. Press the INPUT SEL. button on your TV remote control until
the Video signal from the DVD Recorder appears on the TV
screen.
To RF IN
- DVD mode
1. Connect the AV2 connector of DVD Recorder and VCR/
Satellite receiver or digital tuner using a SCART cable
(not supplied).
To RF OUT
2. Connect the AV1 connector to the SCART AV connector on
TV.
3. Turn on the DVD Recorder, VCR/Satellite receiver or digital
tuner and TV.
RF Cable
4. Set Input mode on AV2.
To ANT INPUT
- TV mode
1. Press the TV/DVD button on remote control,then “TV”
appear on Front LED display. (or turn off DVD Recorder.)
■ The RF cable connection of this DVD Recorder sends
only signals of TV.
You must connect SCART cable or Audio/Video cables
to watch a signal from your DVD Recorder.
2. You can watch programmes from a satellite or digital tuner
connected to this DVD Recorder, even when the DVD
Recorder is turned off.
■ TV mode
Press the TV/DVD button on remote control, then
"TV" appear on Front LED display (or turn off DVD
Recorder).
English - 15
01403A-R149-XEU-ENG.indb 15
2007-03-09 오후 11:11:10
▌ Case 1 : Connecting to a Video
(Composite) output jack
Connecting & Setting Up
Other type of connecting
the Video output cable
There are several ways to output video signal not using scart
cables. Select one of the following video connecting that
best suits you below.
1. Connect a video(yellow) cable between the VIDEO (yellow)
OUT jack on DVD Recorder and VIDEO (yellow) INPUT jack
on your TV (or AV amplifier).
• You will enjoy regular quality images.
• Case 1 : Connecting to a Video (Composite) output jack
• Case 2 : Connecting to an S-Video output jack
• Case 3 : Component Video output jacks
2. Connect audio cables (white and red) between the AUDIO
OUT jacks on the DVD Recorder and AUDIO IN jacks on TV (or
AV amplifier).
(See page 18)
S-Video, Component video and Progressive
Output Modes
yellow
Video/Audio Cable
• S-Video and Component video output are available only if
your TV supports S-Video input or Component video input,
respectively. If S-Video or Component video output does not
work, check the TV connections and the TV input selection
settings.
• Compared to standard interlaced video, progressive scan
doubles the amount of video lines fed to your TV, resulting in
a more stable, flicker-free, clear image than interlaced video.
This is only available with TVs that support progressive scan.
• Progressive Scan Output (576p)
Consumers should note that not all high definition television
sets are fully compatible with this DVD Recorder and may
cause artifacts to be displayed in the picture, in case of
576 progressive scan picture problems, It is recommended
that the user switch the connection to the ‘standard
definition’ output. If there are questions regarding our TV set
compatibility with this model 576p DVD Recorder, please
contact our customer service centre.
yellow
English - 16
01403A-R149-XEU-ENG.indb 16
2007-03-09 오후 11:11:11
▌Case 3 : Component Video output jacks
▌Case 2 : Connecting to an S-Video
output jack
1. Connect an S-Video cable (not included) between the
S-VIDEO OUT jack on DVD Recorder and S-VIDEO INPUT jack
on your TV (or AV amplifier).
2. Connect audio cables (white and red) between the AUDIO
OUT jacks on the DVD Recorder and AUDIO IN jacks on TV (or
AV amplifier).
(See page 18)
3. After connecting, refer to the page 25 to 26
• You will enjoy high quality and accurate colour reproduction
images.
green
blue
red
green
Connecting & Setting Up
2. Connect audio cables (white and red) between the AUDIO
OUT jacks on DVD Recorder and AUDIO IN jacks on TV (or
AV amplifier).
• You will enjoy high quality images.
1. Connect Component video cables(not supplied) between
the COMPONENT OUT(Y, PB, PR) jacks on DVD Recorder and
COMPONENT IN (Y, PB, PR) jacks on your TV.
blue
red
■ Make sure that the colour coded connections match.
The Y, PB, PR component output jacks of your
DVD Recorder must be connected to the exact
corresponding component input jacks on your TV.
■ Progressive setting is only available when the Video
Out is set to Component. (See page 26)
English - 17
01403A-R149-XEU-ENG.indb 17
2007-03-09 오후 11:11:13
Other type of connecting
the Audio output cable
Connecting & Setting Up
There are several ways to output audio signal not using
scart cables. Select the audio connection that best suits you
below.
• Case 1 : Connecting to your TV
• Case 2 : Connecting to a stereo amplifier with AV output
jacks
• Case 3 : Connecting to an AV amplifier with a digital output
jack
red
white
red
white
Front(L)
speaker
Front(R)
speaker
Manufactured under licence from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of DTS, Inc.
▌Case 1 : Connecting to your TV
If your TV has audio input jacks, use this connection.
▌Case 3 : Connecting to an AV
amplifier with a digital output jack
If your AV amplifier has a Dolby Digital, MPEG2 or DTS decoder
and a digital input jack, use this connection.
To enjoy Dolby Digital, MPEG2 or DTS sound, you will need to
set up the audio settings.
(See pages 24-25)
yellow
white
red
yellow
white
red
or
▌Case 2 : Connecting to a stereo
amplifier with AV output jacks
Rear(R)
Rear(L)
If your stereo amplifier only has AUDIO INPUT jacks (L and R),
use the AUDIO OUT jacks.
Front(R)
Front(L)
Subwoofer Centre
English - 18
01403A-R149-XEU-ENG.indb 18
2007-03-09 오후 11:11:15
System Setup
On-Screen Menu Navigation
DVD-Recorder
Programme
No Disc
Programme
VideoPlus+
Setup
Scheduled Record List
►
VideoPlus+ Extended : Off
►
►
The on-screen menus allow you to enable or disable various functions on
your DVD Recorder.
Press the Menu button to open the on-screen menu and then, use the
following buttons to navigate through the on screen menus.
1. EXIT Button
Press this button to exit the on-screen menu.
OK
MOVE
RETURN
2. ▲▼, ◄ ► Buttons
Press these buttons on remote control to move the selection bar ▲▼,◄ ►
to cycle through the menu options.
EXIT
DVD-Recorder
Title List
DVD-RW(VR)
Title List
Title List
►
3. OK Button
Press this button on the remote control to confirm any new settings.
Disc Manager
Programme
Setup
OK
MOVE
RETURN
EXIT
System Setup
4. RETURN Button
Press this button on the remote control to return to the Previous Menu
screen displayed or to exit the on-screen Menu.
Playlist
Plug & Auto Setup
Your DVD Recorder will automatically set itself up when it is plugged in for
the first time. TV stations and clock will be stored in memory. The process
takes a few minutes. Your DVD Recorder will then be ready for use.
1. Connect the RF cable as indicated on page 15.
(Connecting Your DVD Recorder to the TV Using the RF Cable and scart
cable.)
DVD-Recorder
Auto Setup
No Disc
3. Press the OK button or wait for a few seconds to start the auto setup.
Auto setup will be started.
4. Auto Channel scan will be started.
• The number of stations automatically stored by the DVD Recorder depends
on the number of stations that it has found.
Check antenna and TV cable connection.
OK
2. Plug the DVD Recorder into the mains.
“Auto” in the front panel display flickers.
5. Check the date and time.
• If it is correct, press the OK button then the date and time will be saved.
If you don't press the OK button, the date and time will be saved
automatically after 5 seconds.
• If it is incorrect, you can set it up manually.
RETURN
Auto Channel Memory
17%
■ Now, DVD Recorder is ready for use. Function for “Plug & Auto Setup” is
fixed already. So if you want to change this fixed one, you can change
it by Presetting the Stations in OSD “Presetting Channels with the
Manual setup function” menu. (see page 21)
Stop
DVD-Recorder
Auto Setup
No Disc
Date
Time
JAN
01
2007
12
Auto Clock
00
On
MON
MOVE
OK
RETURN
English - 19
01403A-R149-XEU-ENG.indb 19
2007-03-09 오후 11:11:17
Setting the Clock
DVD-Recorder
Clock Set
This menu is used to set the current time.
You need to set the time to use timer recording.
No Disc
Programme
Setup
Date
Time
JAN
01
2007
12
Auto Clock
00
On
MON
MOVE
OK
RETURN
EXIT
1. With the DVD Recorder in Stop mode/No Disc mode, press the MENU
button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ► button.
3. Press the ▲▼ buttons to select Clock Set, then press the OK or ► button.
Use the ▲▼◄ ► buttons to input Time, Date or Year. Use number buttons
to input clock data directly.
4. Press the OK button, then the date and time will be saved.
If you don’t press the OK button, it will not be saved.
■ You must have the RF cable connected to set the Auto Clock.
(See page 15)
System Setup
■ The DVD Recorder automatically sets the clock according to the time
signal broadcast between the channels PR1 to PR5. If you do not need
the Auto clock set function, select Off.
Presetting Channels with the Auto Setup
function
This feature allows you to manually set the DVD Recorder tuner band to
Antenna or Cable, whichever you connected to the Antenna In jack during
initial setup.
Auto Channel Memory
17%
Stop
1. With the DVD Recorder in Stop mode/No Disc mode, press the MENU
button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ► button.
3. Press the ▲▼ buttons to select Install, then press the OK or ► button.
4. Press the ▲▼ buttons to select Auto Setup, then press the OK or ► button.
The message “Your data will be lost. Press [OK] to continue, [MENU] to exit.” is
displayed.
5. Press the OK button to continue.
If you want to exit, press the EXIT button.
6. Channel scan will be started.
Press the OK button to stop the Auto Setup.
English - 20
01403A-R149-XEU-ENG.indb 20
2007-03-09 오후 11:11:19
Presetting Channels with the Manual Setup
function
PR
CH
01
02
03
04
05
06
07
1
-------------
Manual Setup
Name
MOVE
OK
Manual Setup
01
PR
CH
◄1►
---Name
MFT
--- --Done
OK
Edit
Edit
Delete
Swap
RETURN
►
►
►
►
►
►
►
EXIT
1. With the DVD Recorder in Stop mode/No Disc mode, press the MENU button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ► button.
3. Press the ▲▼ buttons to select Install, then press the OK or ► button.
4. Press the ▲▼ buttons to select Manual Setup, then press the OK or ►
button.
5. Press the ▲▼ buttons to select a PR(programme) you wish to edit, delete,
or swap, then press the OK or ► button.
Select Edit, Delete or Swap using the ▲▼ buttons, then press the OK or ►
button.
• Edit : You can add or edit PR(programme). After change PR
informations(CH, Name, Decoder, MFT), select Done, then press the OK
button.
- CH : Tune the channel using ◄ ► buttons.
- Name : Display station name automatically detected in broadcasting signal.
If not detected, you can edit name by using ▲▼◄ ► buttons.
- MFT : You can tune up the channel frequency better using ◄ ► buttons.
• Delete : the channel information of selected PR(programme) will be
removed.
• Swap : You can swap the channel information of two PR(programme). For
example, if you wish to swap PR2 and PR5, select swap at PR2, then press
the OK button at PR5.
System Setup
MOVE
----------------------
You can add preset channel that Auto Channel Search missed. And you
can delete a channel you wish to remove. You can programme the order of
channels.
English - 21
01403A-R149-XEU-ENG.indb 21
2007-03-09 오후 11:11:21
Setting up the Language Options
Language
DVD-Recorder
No Disc
Programme
Audio
: Original
►
Setup
Subtitle
: Automatic
►
Disc Menu
: English
►
On-Screen Menu : English
►
MOVE
OK
RETURN
EXIT
If you set the language options in advance, they will come up automatically
every time you watch a movie.
1. With the DVD Recorder in Stop mode/No Disc mode, press the MENU
button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ► button.
3. Press the ▲▼ buttons to select Language, then press the OK or ► button.
Language setup menu will be displayed.
4. Press the ▲▼ buttons to select the desired language option, then press the
OK or ► button.
• Audio : For the speaker sound.
• Subtitle : For the disc subtitles.
• Disc Menu : For the disc menu contained on the disc.
• On-Screen Menu : For the screen of your DVD Recorder.
System Setup
5. Press the ▲▼ buttons to select the desired language, then press the OK or
► button.
■ If the selected language is not recorded on the disc, the original prerecorded language is selected.
■ The selected language will only appear if it is supported on the disc.
English - 22
01403A-R149-XEU-ENG.indb 22
2007-03-09 오후 11:11:23
Setting up the System Options
System
DVD-Recorder
No Disc
Programme
EP Mode Time
: 6 Hours
►
Setup
Chapter Creator
: Off
►
Quick Recording : Off
►
This function allows you to setup the system setting.
1. With the DVD Recorder in Stop mode/No Disc mode, press the MENU
button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ► button.
3. Press the ▲▼ buttons to select System, then press the OK or ► button.
MOVE
OK
RETURN
4. Press the ▲▼ buttons to select desired option, then press the OK or ►
button.
EXIT
5. Press the ▲▼ buttons to select the desired menu, then press the OK or ►
button.
DVD-Recorder
System
No Disc
Programme
EP Mode Time
: 66 Hours
Hours
►
Setup
Chapter Creator
Hours
: 8Off
►
MOVE
OK
►
RETURN
You can select one of four recording modes by pressing the REC MODE
button repeatedly.
EP mode is one of four REC Mode (XP,SP,LP,EP)
In EP(Extended Play) mode, you can set recording time to 6 or 8 hours by this
setting.
EXIT
▌Automatic Chapter Creation
(V mode)
A DVD-Video consists of ‘Titles’ and ‘Chapters’. When you record one
programme, it makes one Title.
If you use this function, the Title will be divided into Chapters.
Do you want to create the chapter menu
after this recording?
Yes
System Setup
Quick Recording : Off
▌EP Mode Time Setting
No
• On: Select this option when you want (Automatic Chapter Creation).
1/1
1
2
3
1. Press the REC button to start recording. (See page 30 about how to set
recording mode) The message “Do you want to create the chapter menu
after this recording?” is displayed.
2. Press the ◄ ► buttons to select Yes and press the OK button.
• A new chapter is created according to the selected recording mode.
A chapter will be about 5 minutes long in XP and SP, and about 15 minutes
long in LP and EP mode.
3. Press the STOP button to stop recording.
Top
Previous
4. To display the created chapters, finalise the disc (see page 59) and then
press the DISC MENU button. The chapter menu will be displayed.
Next
5. Press the ◄ ► buttons to select desired chapter and press the OK button.
• Off: Select this option when you do not want (Automatic Chapter Creation).
■ The Automatic Chapter Creation function does not work during
Timer Recording or when you turn the power off.
■ DVD-R discs cannot be unfinalised.
DVD-Recorder
System
No Disc
Programme
EP Mode Time
: 6 Hours
►
Setup
Chapter Creator
: Off
►
Quick Recording : Off
Off
►
On
MOVE
OK
RETURN
▌Quick Recording Setting
If this function is set to on, both the DVD Recorder and the TV will power
on at the same time, which enables you to immediately record a desired
channel.
EXIT
English - 23
01403A-R149-XEU-ENG.indb 23
2007-03-09 오후 11:11:24
Setting up the Audio Options
DVD-Recorder
Audio
No Disc
Programme
Digital Output
: PCM
Setup
DTS
: Off
►
Dynamic Compression : Off
►
NICAM
►
►
: On
You can connect the DVD Recorder to an external amp or Home Theatre.
Allow you to setup the Audio device and sound status depending on the
audio system in use.
1. With the DVD Recorder in Stop mode/No Disc mode, press the MENU
button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ► button.
MOVE
OK
RETURN
3. Press the ▲▼ buttons to select Audio, then press the OK or ► button.
Audio setup menu will be displayed.
EXIT
4. Press the ▲▼ buttons to select the desired audio option, then press the OK
or ► button.
5. Press the ▲▼ buttons to select the desired item, then press the OK or ►
button.
System Setup
▌Digital Output
DVD-Recorder
Audio
No Disc
Programme
Digital Output
: PCM
PCM
Setup
DTS
: Bitstream
Off
►
►
Dynamic Compression : Off
►
NICAM
►
MOVE
OK
: On
RETURN
EXIT
• PCM : Select this when you have no equipment that can decode Dolby Digital
(or MPEG-2) signal.
When you play Dolby Digital (or MPEG-2) sound track, the digital output are
converted to PCM Stereo.
• Bitstream : Output Dolby Digital (or MPEG-2) audio as bitstream.
Select this when your AV receiver or AV amplifier have Dolby Digital (or
MPEG-2) Decoder.
■ Digital output setting is equally applied to both Dolby Digital and
MPEG-2 audio. LPCM sound track is always outputted as PCM.
It has no relation with Digital Output setting.
■ Be sure to select the correct Digital Output or you will hear no sound
or loud noise.
▌DTS
DVD-Recorder
Audio
No Disc
Programme
Digital Output
: PCM
Setup
DTS
:Off
Off
►
Dynamic Compression :On
On
►
NICAM
►
►
: On
• Off : Doesn’t output DTS signal.
Select this when your AV receiver or AV amplifier does not have DTS decoder.
• On : Outputs DTS Bitstream via digital output when you play DTS track.
Select this only when your AV receiver (or AV amplifier) have DTS decoder.
■ When DTS soundtrack is played, sound does not output from AV Audio
Output.
MOVE
OK
RETURN
EXIT
English - 24
01403A-R149-XEU-ENG.indb 24
2007-03-09 오후 11:11:26
▌Dynamic Compression
This is only active when a Dolby Digital signal is detected.
DVD-Recorder
Audio
No Disc
Programme
Digital Output
: PCM
►
Setup
DTS
: Off
►
Dynamic Compression :Off
On
:On
On
►
NICAM
MOVE
OK
RETURN
►
▌NICAM
EXIT
DVD-Recorder
Audio
No Disc
Programme
Digital Output
: PCM
Setup
DTS
: Off
►
Dynamic Compression : On
►
:Off
On
On
►
NICAM
OK
RETURN
►
NICAM programmes are divided into 3 types. NICAM Stereo, NICAM Mono
and Bilingual (transmission in another language). NICAM programmes are
always accompanied by a standard mono sound broadcast and you can
select the desired sound by setting NICAM on or off.
• Off : Only set at this position to record the standard mono sound during
a NICAM broadcast if the stereo sound is distorted due to inferior
reception conditions.
• On : NICAM mode
EXIT
Setting up Video Options
Video
DVD-Recorder
No Disc
Programme
TV Aspect
Setup
3D Noise Reduction : Off
►
Video Output
►
: 16:9 Wide
►
: Component
You can enjoy high quality image through RGB or Component video
connections.
System Setup
MOVE
• Off : You can enjoy the movie with the standard Dynamic Range.
• On : When Movie soundtracks are played at low volume or from smaller
speakers, the system can apply appropriate compression to make lowlevel content more intelligible and prevent dramatic passages from
getting too loud.
1. With the DVD Recorder in Stop mode/No Disc mode, press the MENU
button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ► button.
3. Press the ▲▼ buttons to select Video, then press the OK or ► button.
Video setup menu will be displayed.
OK
MOVE
RETURN
EXIT
4. Press the ▲▼ buttons to select desired video option, then press the OK or
► button.
5. Press the ▲▼ buttons to select the desired item, then press the OK or ►
button.
▌TV Aspect
DVD-Recorder
Video
No Disc
Programme
TV Aspect
: 4:3
16:9LetterBox
Wide
►
Setup
3D Noise Reduction : 4:3
Off Pan-Scan
►
Video Output
►
MOVE
OK
: 16:9
Component
Wide
RETURN
Depending on the type of television you have, you may want to adjust the
screen setting. (aspect ratio)
• 4:3 LetterBox : Select when you want to see the total 16:9 ratio screen DVD
supplies, even though you have a TV with a 4:3 ratio screen.
Black bars will appear at the top and bottom of the screen.
• 4:3 Pan-Scan : Select this for conventional size TV when you want to see
the central portion of the 16:9 screen. (Extreme left and right side of movie
picture will be cut off.)
EXIT
• 16:9 Wide : You can view the full 16:9 picture on your widescreen TV.
▌3D Noise Reduction (motion adaptive noise reduction)
DVD-Recorder
Video
No Disc
Programme
TV Aspect
Setup
3D Noise Reduction : Off
Off
Video Output
MOVE
OK
: 16:9 Wide
►
►
: On
Component
RETURN
• On : Provides a cleaner picture through noise reduction (for recording).
• Off : Normal
►
EXIT
English - 25
01403A-R149-XEU-ENG.indb 25
2007-03-09 오후 11:11:28
▌Video output
DVD-Recorder
Video
No Disc
Programme
TV Aspect
Setup
3D Noise Reduction : Off
►
Video Output
►
: 16:9 Wide
►
: Component
Component
RGB
• Component : Select this when the DVD Recorder is connected to a TV with
Component jack.
• RGB : Select this when the DVD Recorder is connected to your TV using
SCART cable.
In Component mode, you can set video output to Progressive(P.SCAN) or
Interlace, see below.
Setting mode
MOVE
OK
RETURN
EXIT
Output jack
Component mode
P.SCAN off mode (Interlace mode) P.SCAN on mode
Component Output
(Y, PB, PR)
O
(TV in progressive mode)
X
O
R, G, B
X
X
Composite
O
X
X
Composite Video out
O
X
O
S-Video out
O
X
O
AV1 Scart
System Setup
O
RGB Mode
Progressive scan
If the TV supports Progressive Scan, press the P.SCAN button on the front of
the DVD Recorder to enjoy.
Setting up the Progressive scan
1. With the DVD Recorder in Stop mode, press the P.SCAN button on the front
of the DVD Recorder.
The message “Press [Yes] to confirm Progressive scan mode. Otherwise,
press [No].” will appear.
2. Press the ◄ ► buttons to select Yes, and then press the OK button.
3. Set your TV to Progressive input (using the TV remote control.)
■ Do not press the P.SCAN button if you are using a TV that does not
support Progressive mode. Nothing will be displayed on the screen if
pressed.
■ Progressive setting is only available when the Video Out is set to
Component.
■ Progressive setting is only available when the DVD recorder is in stop
mode.
Canceling the Progressive scan
1. With the DVD Recorder in Stop mode, press the P.SCAN button on the front
of the DVD Recorder.
The message “Press [Yes] to confirm Interlace scan mode. Otherwise, press
[No].” will appear.
2. Press the ◄ ► buttons to select Yes, and then press the OK button.
3. Set your TV to Interlace input (using the TV remote control.)
■ If you press the P.SCAN button by mistake when your TV does not
support Progressive mode, you need to release the Progressive mode.
To release the Progressive mode, press the P.SCAN button on the front
panel 2 times.
■ The screen will recover after the PS
turns off.
LED on the front panel display
English - 26
01403A-R149-XEU-ENG.indb 26
2007-03-09 오후 11:11:30
Setting up the Parental Control
Parental Control
DVD-Recorder
No Disc
Programme
Password
:Off
Off
►
On
Setup
The Parental Control function works in conjunction with DVDs that have
been assigned a rating which helps you control the types of DVDs that your
family watches. There are up to 8 rating levels on a disc.
1. With the DVD Recorder in Stop mode/No Disc mode, press the MENU
button.
2. Press the ▲▼ buttons to select Setup, then press the OK or ► button.
MOVE
OK
RETURN
3. Press the ▲▼ buttons to select Parental Control, then press the OK or ►
button.
The ‘Create the password’ message will be displayed.
EXIT
4. Enter the 4-digit password using the 0 to 9 buttons on the remote control.
The ‘Confirm the password’ message will be displayed. Enter your password
again.
5. Press the OK or ► button to select Password.
▌About the Rating Level
Parental Control
DVD-Recorder
No Disc
Programme
Password
►
Setup
Rating Level
►
:On
Level 8 Adults
:Level
Level71 Kids
Level 6
Change Password
Level 5
Level 4
Level 3
Level 2
Level 1 Kids
MOVE
OK
RETURN
►
EXIT
System Setup
6. Press the ▲▼ buttons to select On, then press the OK or ► button.
1. Press the ▲▼ buttons to select Rating Level.
2. Press the OK or ► button.
The rating level will be displayed.
3. Press the ▲▼ buttons to select Rating Level you want, then press the OK or
► button.
For example, if you select up to Level 6, discs that contain Level 7, 8 will not
play. A larger number indicates that the programme is intended for adult
use only.
▌About the Change Password
Parental Control
DVD-Recorder
No Disc
Programme
Password
: On
►
Setup
Rating Level
: Level 1 Kids
►
Change Password
MOVE
OK
RETURN
►
EXIT
1. Press the ▲▼ buttons to select Change Password.
2. Press the OK or ► button.
The ‘Enter the password’ message will be displayed.
3. Enter the 4-digit password using the 0 to 9 buttons on the remote control.
The ‘Confirm the password’ message will be displayed. Enter your password
again.
■ If you forgot your password, remove the disc. Press and hold down
the PROG (
) buttons on the front panel of the DVD Recorder
simultaneously for more than 5 seconds. All setting including the
password will revert to the factory setting.
English - 27
01403A-R149-XEU-ENG.indb 27
2007-03-09 오후 11:11:32
Recording
This section shows various DVD recording methods.
This DVD Recorder can record on various types of discs.
Before recording, read the following instructions and select
the disc type according to your preference.
Recordable discs
This DVD Recorder can record on the following discs.
DVD-RAM
DVD-RW
DVD-R
■ Finalise
- This closes the DVD-R/-RW so no additional
recording can be done.
■ Unfinalise
- This allows additional recording on a DVD-RW disc
originally recorded on the DVD Recorder.
- A DVD-RW disc that has been recorded by DAO
(Disc At Once) in a PC cannot be unfinalised.
- A DVD-RW disc that has been recorded in Video
Mode of a different maker’s recorder cannot be
unfinalised.
- A DVD-R disc cannot be unfinalised.
• DVD-RWs and DVD-RAMs are rewritable.
• DVD-Rs are non-rewritable.
▌Compatibility between Samsung and
Other Company’s Recorder
Recording Recording
Additional Recording
Finalising
format
Device
in Samsung Recorder
Samsung
X
Recordable
VR
DVD-RAM
Mode Other Company
X
Recordable
finalised Not recordable
Samsung
not finalised Recordable
VR
Mode
finalised Not recordable
Other Company
not finalised Recordable
DVD-RW
finalised Not recordable
Samsung
not finalised Recordable
V Mode
finalised Not recordable
Other Company
not
Not recordable
finalised
finalised Not recordable
Samsung
not finalised Recordable
DVD-R V Mode
finalised Not recordable
Other Company
not finalised Not recordable
Recording
Disc Types
English - 28
01403A-R149-XEU-ENG.indb 28
2007-03-09 오후 11:11:33
Recording Formats
DVD-RAM
Since available functions differ depending on the disc type, select a disc that
best fits your preferences;
When you insert an unused disc, the following message appears
Unformatted Disc
Do you want to format this disc?
Yes
No
• DVD-RAM : Use after formatting the disc.
• DVD-RW : Use after initialising the disc.
In case of DVD-RW disc, you can change the mode. Refer to Fomatting a Disc
on pages 58.
• DVD-R : Formatting DVD is unnecessary and only Video Mode Recording is
supported.
DVD-RW
▌DVD-RW(Video mode)/-R
Uninitialised Disc
Do you want to initialise this disc?
Yes
No
• Chapters will be created automatically when you finalise recording on DVD-R
/ DVD-RW discs in Video mode with the Chapter Creator has been set to On.
The chapter’s length (interval between chapters) varies according to the
recording mode.
• Simple editing (erasing titles/changing title name)
▌DVD-RAM/-RW(VR mode)
• This mode allows multiple editing functions (such as deletion of the whole
title, partial deletion of a title, etc.)
• Various editing options using a created Playlist
Recording
■ You can initialise discs automatically using EZ REC MODE
(see page 37)
English - 29
01403A-R149-XEU-ENG.indb 29
2007-03-09 오후 11:11:35
Recording Mode
Select one of four recording modes by pressing the REC MODE button
repeatedly while the DVD Recorder is in Stop mode for the desired recording
time and picture quality.
In general, picture quality improves as the recording time decreases.
In FR mode, the most suitable record mode is adjusted automatically,
according to remaining time on the disc and length of the timer recording.
This function is selected only one mode in XP, SP, LP and EP modes and you
can use this mode for timer recording.
Mode
Characteristic
XP
(high quality mode)
Select when the video
quality is important.
Select to record in
standard
quality.
Select when a long
recording time is
required.
SP
(standard quality mode)
LP
(long recording mode)
EP
(extended mode)
Select when a longer
recording time is
required.
FR
(Flexible Recording)
for timer recording only
see page 34.
Recording Times Data
Rates
Approx. 1 hour
about 8 Mbps
Approx. 2 hours
about 4 Mbps
Approx. 4 hours
about 2 Mbps
Approx. 6 hours/
about 1,2 Mbps
Approx. 8 hours/
about 0,8 Mbps
Approx 1 to 8 hours
Approx 0,8 to 8Mbps
Recording
• The dual layer DVD-Rs have approximately double capacity than single layer
DVD-Rs. (See page 38.)
Unrecordable video
Video with copy protection cannot be recorded on this DVD Recorder.
When the DVD Recorder receives a copy guard signal while recording,
recording stops and the following message appears on the screen.
You cannot record copy protected movie.
English - 30
01403A-R149-XEU-ENG.indb 30
2007-03-09 오후 11:11:36
Concerning Copy Control Signals
TV broadcasts that contain copy control signals may have one of the following
three signal types, Copy-Free, Copy-Once and Copy-Never.
If you want to record a copy-once type programme, use DVD-RAM/-RW with
CPRM in VR Mode.
Signal type
Media
DVD-RAM (Ver.2.0)
DVD-RW (Ver.1.1)
DVD-RW (Ver.1.1)
with CPRM
VR mode
Video mode
DVD-R
Copy-Free
Copy-Once
Copy-Never
O
O
O*
-
-
O
O
O
O*
-
-
Once “Copy Once” has been recorded, recording cannot be done anymore.
Content Protection for Recordable Media (CPRM)
CPRM is a mechanism that ties a recording to the media on which it is
recorded. It is supported by some DVD recorders, but not by many DVD
players. Each blank recordable DVD has a unique 64-bit media ID etched
in the BCA. When protected content is recorded onto the disc, it can be
encrypted with a 56-bit C2 (Cryptomeria) cipher derived from the media ID.
During playback, the ID is read from the BCA and used to generate a key to
decrypt the contents of the disc.
If the contents of the disc are copied to other media, the ID will be absent
or wrong and the data will not be decryptable.
The INFO function allows you to view the current status and progress of
playback and recording. When recording on an used disc, make sure that
there is enough disc space for recording.
Recording
▌About INFO Button
Press the INFO button.
The display window of disc information appears.
DVD-RW(VR)
Disc Name
Total Title
Total Playlist
Recordable Time
Protection
Screen
JAN 01 2007 MON
Disc Info
Disc
15
1
02:12 SP
Not Protected
PR 11 [DUALL]
12:00
1. Disc Type
2. Current information display status
3. Disc Name
4. Total Title : Total number of titles
5. Total Playlist : Total number of Playlists
6. Recordable Time : The longest continuous recording time in each of the
recording modes(approximate)
7. Date : Current date and time
■ Items in the display differ depending on the disc type or recording
format.
■ With DVD-RAMs or DVD-RWs, you can free up disc space by erasing
titles.
■ Press the info button again with the unit in playback or recording,
then you can check the current status.
English - 31
01403A-R149-XEU-ENG.indb 31
2007-03-09 오후 11:11:37
Recording immediately
Record Mode
XP (00:40)
Before you start
1. Check that the disc has enough available space for the recording.
Adjust the recording mode.
2. Press the OPEN/CLOSE button and place a recordable disc on the disc tray.
Recording : AV 1
3. Press the OPEN/CLOSE button to close the disc tray.
Wait until “LOAD” disappears from the front panel display.
▌Recording the current TV programme you are watching
1. Press the PROG ( / ) or number ( ~
current programme you want to record.
) buttons to select the
2. Press the REC MODE button repeatedly, to select the recording speed
(quality).
SP
LP
EP
XP
Recording
3. Press the REC button.
Information concerning the channel is displayed on the screen, then
recording begins. REC icon( ) is displayed on the front panel.
▌Recording from external equipment you are watching
1. Press the INPUT SEL. button to select the input source according to the
connection you made.
The front panel display changes in the following sequence:
PR Number
AV1
AV2
AV3
2. Press the REC MODE button repeatedly, (or press the REC MODE button,
then press ▲▼ button) to select the recording
speed(quality).
SP
LP
EP
XP
3. Press the REC button.
To pause recording
Press the PLAY/PAUSE( ) button to pause a recording in progress.
• Press the PLAY/PAUSE( ) button again to resume recording.
• You can switch channels by pressing the PROG ( / ) buttons while
recording pauses.
To stop recording
Press the STOP button to stop a recording in progress.
• When using DVD-RAM/DVD-RW/DVD-R discs, the message “Updating the
disc information. Please wait for a moment.” is displayed.
English - 32
01403A-R149-XEU-ENG.indb 32
2007-03-09 오후 11:11:38
■ You can not change the recording mode and the PROG while
recording.
■ Up to 99 titles can be recorded onto a DVD-RAM/-RW/-R disc.
■ Recording will stop automatically if there is no free space left for
recording.
■ Recording will stop automatically if a copy protected image is
selected.
■ DVD-RAM/DVD-RW discs must be formatted before starting to record.
Most new discs are sold unformatted.
■ Do not use DVD-R authoring discs with this DVD Recorder.
Making a One Touch Recording (OTR)
You can set the DVD Recorder to record in preset increments by pressing the
REC button repeatedly.
Recording
1. If you want to record a TV channel, press the PROG ( / ) or number
buttons to select a desired channel.
If you want to record through a connected external component, press the
INPUT SEL. button to select an appropriate external input (AV1, AV2, or
AV3).
• TV PROGRAMME : 1 to 99
2. Press the REC button to start recording.
3. Press the REC button repeatedly to adjust the desired recording time.
0:30
1:00
... 4:00
5:00
... 9:00
normal
■ The timer counter decreases by the minute from 9:00 to 0:00, then the
DVD Recorder stops recording and is powered off.
English - 33
01403A-R149-XEU-ENG.indb 33
2007-03-09 오후 11:11:41
Making a Timer Recording
Programme
DVD-Recorder
DVD-RW(VR)
Title List
VideoPlus+
Playlist
Scheduled Record List
►
Disc Manager
VideoPlus+ Extended : Off
►
►
Before you start
Programme
Setup
OK
MOVE
RETURN
EXIT
DVD-Recorder
Scheduled Record List
DVD-RW(VR)
Current Time 12:05
No. Source Day Start End Speed PDC Edit
No. 01
Source
Day
Start
End
Speed
PR 01
01 SUN
12:05
14:05
SP
PDC
Off
Available Time 00:48 SP
MOVE
OK
RETURN
EXIT
1. Check the antenna cable is connected.
2. Check the remaining time of the disc.
3. Check the date and time are correct.
Make sure the Clock (Setup-Clock Set) must be set before you proceed with
a timer recording. (See page 20)
1. With the DVD Recorder in Stop mode, press the TIMER button.
2. Press the ▲▼ buttons to select Scheduled Record List, then press the
OK or ► button.
• The Timer Recording screen is displayed.
3. Press the OK button, then set timer recording option.
• Fill the input items using the direction buttons and number buttons.
◄ ► : Moves to the previous/next item,
▲▼, 0~9 : Sets a value.
• Source : The video input source (“AV1”, “AV2”, “AV3”) or the broadcasting
channel you want to make a timer recording from.
Recording
• Day : Timer Recording allows setting the recording time within one month
period. Set the recording day.
01 SUN
02 MON
03 TUE
04 WED
Daily
MO-SA
MO-FR
W-SA
31 TUE
W-SU
• Start/End Time : Start and end time of the timer recording.
• Speed (Recording Mode) :
- FR (Flexible Recording) : Select when you want to set video quality
automatically.
In FR mode, the most suitable record mode is adjusted automatically,
according to remaining time on the disc and length of the timer recording.
This function is selected only one mode in XP, SP, LP and EP modes and you
can use this mode for timer recording.
- XP (high quality) : Select when video quality is important. (Approx. 1 hour)
- SP (standard quality) : Select to record in standard quality. (Approx. 2 hours)
- LP (low quality) : Select when a long recording time is required.
(Approx. 4 hours)
- EP (extended) : Select when a longer recording time is required.
(Approx.6 hours or 8 hours)
• PDC : PDC(Programme Delivery Control) function.
- If you set this function on, you can control the starting and ending time
of recording by special signal included in the broadcasting signal. If a
TV programme is shortened or starts earlier or later than scheduled, this
function synchronizes the starting and ending time of recording with the
actual broadcasting time automatically.
- Set up the start-time EXACTLY according to the published TV schedule.
Otherwise the timer recording will not take place.
- Do not select PDC or VPS unless you are sure the programme you wish to
record is broadcast with PDC.
English - 34
01403A-R149-XEU-ENG.indb 34
2007-03-09 오후 11:11:43
■ When you are recording at EP mode on a DVD-RW(V)/-R disc, it may
not record the full 6 or 8 hours because the DVD Recorder uses the
VBR(Variable Bit Rate) ENCODING system.
For example, if you record a programme with a lot of action, it uses a
higher bit rate which in turn consumes more disc memory.
4. Press the OK button.
If the timer settings overlap
The first programme has priority. After recording of the first programme is
complete, the second programme starts being recorded.
5. Turn the power off to finish the Timer Recording setting. Timer Recording
will not work when the power is on.
•
will appear on the front panel display. It means that a timer recording is
registered.
•
will blink if disc is not inserted.
■ When the scheduled recording is operating, the programme being
recorded will not display on TV.
• Press the TV/DVD button if you want to see the programmed being
recorded on TV.
• Press the TV/DVD button again if you don’t want to see the
programmed being recorded on TV.
■ The timer recording time may differ from the set time depending on
disc status and overall timer recording status (for example, recording
times overlapping, or when the previous recording ends within 2
minutes before the start time of the next recording.)
■ You can make the Timer Recording up to 12 programmes
Recording
Editing the Scheduled Record List
DVD-Recorder
Scheduled Record List
DVD-RW(VR)
Current Time 12:27
No. Source Day Start End Speed PDC Edit
No. 01
Source
Day
Start
End
PR 01
01 SUN
12:07
14:07
Available Time
MOVE
Speed PDC
SP
Off
00:48 SP
OK
Follow these directions to edit the timer record list.
1. With the DVD Recorder in Stop mode, press the TIMER button.
RETURN
EXIT
2. Press the OK or ► button.
3. Press the ▲▼ buttons to select the number of the timer recording you want
to edit, then press the OK or ► button.
• The Edit and Delete items are displayed.
4. Press the ▲▼ buttons to select Edit, then press the OK or ► button.
• The Timer Record Input item is displayed.
Edit the items you want to modify.
See the “Making a Timer Recording” section for more information on Timer
Recording Input items.
5. Press the OK button to confirm the edited setting.
English - 35
01403A-R149-XEU-ENG.indb 35
2007-03-09 오후 11:11:45
Deleting the Scheduled Record List
DVD-Recorder
Scheduled Record List
DVD-RW(VR)
Current Time 12:27
No. Source Day Start End Speed PDC Edit
01
02
03
PR 01 SAT 01 15:07
14:07
SP
CH
No. 01
PR 01 SUN 01 12:08 14:08
SP
CH
/
/
:
:
Do you want to delete ’No.01’ ?
Yes
Follow these directions to delete an entry from the timer record list.
►
►
1. With the DVD Recorder in Stop mode, press the TIMER button.
2. Press the OK or ► button.
No
OK
MOVE
►
RETURN
EXIT
3. Press the ▲▼ buttons to select the number of the timer recording you
want to delete, then press the OK or ► button.
• The Edit and Delete items are displayed.
4. Press the ▲▼ buttons to select Delete, then press the OK or ► button.
5. Press the ◄ ► buttons to select Yes, then press the OK button.
• The selected entry will be deleted from the list.
■ You can not delete programmes that are currently being recorded.
Using the Video Plus+Feature
Programme
DVD-Recorder
DVD-RW(VR)
Title List
VideoPlus+
Playlist
Scheduled Record List
►
Disc Manager
VideoPlus+ Extended : Off
►
►
Recording
Programme
Setup
OK
MOVE
RETURN
EXIT
VideoPlus+
DVD-Recorder
DVD-RW(VR)
Title List
Enter VideoPlus+ Code number. [0-9]
Playlist
Disc Manager
Programme
Setup
0-9 NUMBER
OK
RETURN
EXIT
DVD-Recorder
Scheduled Record List
DVD-RW(VR)
Current Time 12:00
No. Source Day Start End Speed PDC Edit
No. 01
Source
Day
Start
End
PR 01
01 MON
12:01
14:01
Available Time
MOVE
Speed PDC
SP
Off
RETURN
EXIT
DVD-Recorder
Scheduled Record List
DVD-RW(VR)
Current Time 12:00
No. Source Day Start End Speed PDC Edit
01
02
PR 01 01 MON 12:01
:
MOVE
OK
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Programme, then press the OK or ►
button.
3. Press the ▲▼ buttons to select VideoPlus+, then press the OK or ►
button.
• A message is displayed to allow you to enter the Video Plus+ code.
4. Press the number buttons to enter the code of the programme that you
want to record in your television magazine.
• If you want to correct the Video Plus+ code that you are entering:
- Press the ◄ button until the digit to be corrected is cleared.
- Enter the correct digit.
5. Press the OK button.
• The information concerning the programme is displayed.
• When using the Video Plus+ function for the first time with stored stations,
the programme number flashes. This one time, you must enter the PR
number manually by pressing the ▲▼ buttons.
6. If the programme and times are correct, press the OK button.
00:42 XP
OK
Before presetting your DVD Recorder.
• Switch on both the television and your DVD Recorder.
• Check that the date and time are correct.
Up to twelve programmes can be preset.
14:01
:
SP
RETURN
Off
►
►
EXIT
7. Turn the power off by pressing the STANDBY/ON button to activate the
timer recoding setting.
• Refer to pages 34~35 if you want to
- Check whether the timer Recording has set correctly or not.
- Cancel a preset recording.
■ The numbers next to each TV programme listing in the magazines
or newspapers are Video Plus+ code numbers, which allow you to
programme your DVD Recorder instantly with the remote control.
Enter the Video Plus+ code for the programme you wish to record.
■ Video Plus+ is a trademark of Gemstar Development Corporation.
The Video Plus+system is manufactured under licence from Gemstar
Development Corporation.
English - 36
01403A-R149-XEU-ENG.indb 36
2007-03-09 오후 11:11:46
Video Plus+ Extended
Programme
DVD-Recorder
DVD-RW(VR)
Title List
VideoPlus+
Playlist
Scheduled Record List
►
Disc Manager
VideoPlus+ Extended : Off
►
►
Programme
1. With the unit in Stop mode, press the MENU button.
Setup
MOVE
OK
RETURN
2. Press the ▲▼ buttons to select Programme, then press the OK or ►
button.
EXIT
Programme
DVD-Recorder
DVD-RW(VR)
Title List
VideoPlus+
Playlist
Scheduled Record List Off
10
VideoPlus+ Extended : Off
20
30
40
50
60
Disc Manager
Programme
Setup
MOVE
To prevent delays or over-runs the DVD Recorder has a function called Video
Plus+ Extended allowing you to extended the recording time by up to 60
minutes.
• Only use if PDC/VPS is not available or set to OFF.
OK
►
3. Press the ▲▼ buttons to select VideoPlus+ Extended, then press the OK
or ► button.
4. Press the ▲▼ buttons to select the Video Plus+Extended time, then the
press OK or ► button.
►
►
RETURN
5. Press the EXIT button to exit the menu.
EXIT
EZ REC MODE
Otherwise press “Off”
On
This function allows you Initialise and Finalise a disc automatically.
1. With the unit in Stop mode/No Disc mode, press the EZ REC MODE button
on the remote control.
Off
Recording
Press “On” to confirm EZ REC mode.
2. Press the ◄ ► buttons to select On, and then press the OK button.
EZ REC MODE is set up.
3. Insert a disc.
If the disc is new, it will initialise automatically.
4. Press the REC button.
Disc Initialise (DVD-V)
Now, initialising..
50%
5. EZ REC MODE will Automatically Finalise the disc under the following
conditions.
50%
- When you press the OPEN/CLOSE button on your DVD Recorder after
recording on at least 30% of the disc. The tray will open after the disc has
been finalised.
- When the disc is full, it will finalise automatically and the Recorder will remain
in stop mode.
- When you make a timer recording and it occupies at least 30% of the disc, the
disc will finalise automatically and the Recorder will power off.
Please note that auto finalisation will not work if the Recorder has more than
one Timer Recording set in the Scheduled Record List.
Disc Finalise
Processing..
■ If you insert a new DVD-RW disc, it will be formatted in V mode after
auto initialising.
■ If you select off, you must initialise (see page 29) and finalise the disc
manually in the Disc Manager menu. (see page 59)
■ The Length of Recording is different according to recording mode.
(see page 30)
English - 37
01403A-R149-XEU-ENG.indb 37
2007-03-09 오후 11:11:48
Playback
This section introduces basic functions of playback and
playback by disc type.
Disc types that can be played
Read the following information before playing a disc.
Disc
Types
Region code (DVD-Video only)
Both the DVD recorder and the discs are coded by
region. These regional codes must match in order
for the disc to play. If the codes do not match, the
disc will not play.
The Region Number for this DVD Recorder is
described on the rear panel of the DVD Recorder.
Logos of Discs that can be played
Playback
D I G I TA L
Dolby Digital
DTS
Digital Audio
Stereo
PAL broadcast
system in U.K,
France, Germany, etc.
MP3
Disc Recorded
Disc Shape Max. Playing Time
Logo content
Single sided(5”)
240min
Double
sided(5”)
480min
DVDVIDEO
VIDEO
AUDIO Single sided(3.5”)
80min
Double sided(3.5”)
160min
Single sided(5”)
74min
AUDIO-CD
AUDIO
Single sided(3.5”)
20min
JPEG Single sided(5”)
JPEG
Image Single sided(3.5”)
MP3 Single sided(5”)
MP3
Audio Single sided(3.5”)
1hr (XP : Excellent Quality)
VIDEO Single sided(5”) 2hrs (SP : Standard Qualit)
AUDIO
(4.7GB)
4hrs (LP : Long Playback)
6 or 8hrs (EP : Extended)
DVD-RAM
2hr (XP : Excellent Quality)
VIDEO Double sided(5”) 4hrs (SP : Standard Qualit)
(9.4GB)
AUDIO
8hrs (LP : Long Playback)
12 or 16hrs (EP : Extended)
1hr (XP : Excellent Quality)
2hrs
(SP : Standard Qualit)
VIDEO
5” (4.7GB)
DVD-RW
AUDIO
4hrs (LP : Long Playback)
6 or 8hrs (EP : Extended)
1hr (XP : Excellent Quality)
Single Layer(5”) 2hrs (SP : Standard Qualit)
(4.7GB)
4hrs (LP : Long Playback)
6 or 8hrs (EP : Extended)
VIDEO
DVD-R
AUDIO
2hr (XP : Excellent Quality)
4hrs
(SP : Standard Qualit)
Double Layer(5”)
(8.5GB)
8hrs (LP : Long Playback)
11 or 15hrs (EP : Extended)
1hr (XP : Excellent Quality)
2hrs (SP : Standard Qualit)
VIDEO
DVD+RW
5” (4.7GB)
AUDIO
4hrs (LP : Long Playback)
6 or 8hrs (EP : Extended)
1hr (XP : Excellent Quality)
2hrs
(SP : Standard Qualit)
Single Layer(5”)
(4.7GB)
4hrs (LP : Long Playback)
6 or 8hrs (EP : Extended)
VIDEO
DVD+R
AUDIO
2hr (XP : Excellent Quality)
Double Layer(5”) 4hrs (SP : Standard Qualit)
(8.5GB)
8hrs (LP : Long Playback)
11 or 15hrs (EP : Extended)
English - 38
01403A-R149-XEU-ENG.indb 38
2007-03-09 오후 11:11:50
▌Discs that cannot be played
• DVD-Video with a region number other than “2” or “ALL”
• 5” 2.6 GB and 5.2 GB DVD-RAM
• 3.9 GB DVD-R Disc for Authoring.
• A DVD±R/DVD-RW(V) disc which has been recorded and not finalised in a
different manufacturer's recorder.
• DVD-ROM/PD/MV-Disc, etc.
• MPEG4/Video CD/CVD/SVCD/CD-ROM/CDV/CD-G/CD-I
■ Playback and/or recording may not work for some types of discs,
or when specific operations, such as angle change and aspect ratio
adjustment, are being performed. Information about the discs is
written in detail on the box. Please refer to this if necessary.
■ Do not allow the disc to become dirty or scratched. Fingerprints, dirt,
dust, scratches or deposits of cigarette smoke on the recording surface
may make it impossible to use the disc for recording.
■ DVD-RAM/±RW/±R discs may not be able to play on some DVD
Recorders, depending on the player, disc and the condition of the
recording.
■ DVD-Recorder can play NTSC discs. But you can see a normal screen
only when your TV supports NTSC.
Playing a Disc
1. Press the OPEN/CLOSE button.
2. Place a disc gently into the tray with the disc’s label facing up.
3. Press the OPEN/CLOSE button to close the disc tray.
• The DVD Recorder does not play discs automatically after the initial power
on.
• When the DVD Recorder is powered on and a disc is in the tray, the DVD
Recorder will be activated and wait in stop status.
• Press the PLAY button to start playback.
4. Press the STOP button to stop playback.
Playback
■ When you stop playing disc, the DVD Recorder remembers where you
stopped.
When you press the PLAY button again, it will pick up where you left
off. (unless the disc is removed or the DVD Recorder is unplugged, or
if you press the STOP button twice.) This function is only applicable to
DVD-VIDEO, DVD-RAM, DVD±RW, DVD±R or Audio CDs (CD-DA).
■ Do not move your DVD Recorder while playing, as this may cause
damage to the disc.
■ Make sure to press the OPEN/CLOSE button to open or close the disc
tray.
■ Do not push the disc tray while it is being opened or closed, as this
may cause a malfunction of the DVD Recorder.
■ Do not place foreign materials on or in the disc tray.
■ Some functions may perform differently or be disabled depending on
the disc type. If this occurs, refer to the instructions written on the disc
case.
■ Be especially careful that children's fingers are not caught between
the disc tray and the tray chassis when it closes.
■ You must only insert one DVD disc at a time. Inserting two or more
discs will not allow playback and may cause damage to the DVD
Recorder.
English - 39
01403A-R149-XEU-ENG.indb 39
2007-03-09 오후 11:11:52
▌Using the Disc Menu & Title Menu
Some discs contain a dedicated menu system that allow you to select special
functions for the title, such as chapters, audio tracks, subtitles, film previews,
information on characters, etc.
For DVD-VIDEO discs
Disc Menu : Press the DISC MENU button to enter the disc menu of the disc.
• Move to the setup menu related to the playback operation.
• You can select the audio languages and the subtitles provided by the disc.
Title Menu : Press the TITLE MENU button to move to the title menu of the
disc.
• Use this button if the disc contains more than one title. Some type of discs
may not support the title menu function.
For DVD-RAM/DVD±RW/±R discs
Title List : Press the TITLE LIST button. Title List shows a list to help you select
a title. Since the title list consists of the information on video that is actually
recorded, if one title is deleted, that title cannot be played again.
PLAY LIST : Press the PLAY LIST button. This refers to a unit of playback, which
is made by selecting a desired scene in the entire Title List. When one playlist is
played, only the scene selected by the user will play and then stop. Since only
the information necessary for playing a desired scene is included in a playlist,
even if that playlist is deleted, the original recording will not be deleted. (only
VR mode)
▌Using the playback related buttons
Playback
Searching through a Chapter or Track
DVD-VIDEO/DVD-RAM
DVD±RW/DVD±R
Fast 1
Fast 4
Fast 1
AUDIO CD
(CD-DA)
X2
Fast 2
Fast 5
X4
Fast 3
Fast 6
X8
X2
During playback, press the SEARCH (
) button on the remote control.
• You can scan the programme in reverse.
• Press and hold the SEARCH(
) button, playback is done at the default
speed of Fast 2.
• If you release the SEARCH(
) button, playback is performed at a normal
speed.
• To return to normal speed playback, press the PLAY button.
English - 40
01403A-R149-XEU-ENG.indb 40
2007-03-09 오후 11:11:53
■ No sound is heard during Scan (Search) mode except Fast 1 mode.
■ For CD(CD-DA), you can hear sound during Scan mode.
■ The speed marked in this function may be different from the actual
playback speed.
Skipping Chapters or Tracks
During playback, press the SKIP (
) button on the remote control.
• If you press the SKIP ( ) button,
it moves to the beginning of the chapter or track or marker(DVD-RAM,
DVD-RW(VR mode)).
Pressing the button once again within 3 seconds returns to the beginning of
the previous chapter or track or marker (DVD-RAM, DVD-RW(VR mode)).
• If you press the SKIP ( ) button,
it moves to the next chapter or track or marker (DVD-RAM, DVD-RW
(VR mode)).
Slow Motion play/Step Motion Play
▌Slow Motion Play
In pause mode, press the SEARCH (
• If you press the SEARCH(
Slow 1
Slow 2
) button,
Slow 3
• If you press the SEARCH(
Slow 1
Slow 2
) button,
Slow 3
) button on the remote control.
• Press and hold the SEARCH (
) button during pause, the disc will play
slowly at a Slow 1 speed.
If the button is released, the pause operation will resume.
• To return to normal speed playback, press the PLAY button.
Playback
■ The speed marked in this function may be different from the actual
playback speed.
▌Step Motion Play
Press the STEP (
pause.
) button on the remote control during playback or
• Each time the button is pressed, a new frame will appear.
If you press the STEP ( ) button,
the previous frame will be activated.
If you press the STEP ( ) button,
the next frame will be activated.
• To return to normal speed playback, press the PLAY button.
English - 41
01403A-R149-XEU-ENG.indb 41
2007-03-09 오후 11:11:56
Using the ANYKEY button
The ANYKEY function allows you to easily search for a desired scene by
accessing title, chapter or time. You can also change the subtitle and audio
settings and set some features including Repeat, Angle, Zoom.
▌Moving to a desired scene directly
If you want to move to a certain title, chapter or time, use this function.
1. Press the ANYKEY button during playback.
DVD-VIDEO
2. Press the ▲▼ buttons to select a Title, a Chapter or a Time.
Title
1/2
Chapter
1/28
Time
00:00:01
Subtitle
Off
Audio
ENG
Repeat
Off
Angle
1/3
Zoom
Off
MOVE
D 5.1CH
3. Press the ◄ ► or number (0~9) buttons to select the desired scene.
Press the OK button.
In case of searching a time, Enter the time in the sequence of hours, minutes,
seconds using the number buttons. ◄ ► are not available.
CHANGE
■ This may not work for some discs. When an audio CD(CD-DA) or an
MP3 disc is inserted, according to a disc type, the information display
may not be appear.
■ The Time Search function does not operate in some discs.
■ To make the screen disappear, press the ANYKEY again.
Repeat Play
▌Playing Repeatedly
DVD-VIDEO
Title
1/2
Chapter
1/28
Time
00:00:01
Subtitle
Off
Audio
ENG
Repeat
Title
Angle
1/3
Zoom
Off
MOVE
D 5.1CH
OK
1. Press the ANYKEY button during playback.
2. Press the ▲▼ buttons to select Repeat, then press the ◄ ► buttons to
select Title or Chapter you want to play repeatedly.
3. Press the OK button.
To return to normal playback
Select Off on the Repeat item or press the CANCEL button.
Playback
■ DVD-RAM, DVD-RW(VR mode), unfinalised DVD±R and unfinalised
DVD-RW (Video mode) do not repeat a chapter.
■ To make the screen disappear, press the ANYKEY again.
▌Playing a Certain section Repeatedly
DVD-VIDEO
Title
1/2
Chapter
1/28
Time
00:00:01
Subtitle
Off
Audio
ENG
Repeat
A-B
Angle
1/3
Zoom
Off
MOVE
1. Press the ANYKEY button during playback.
D 5.1CH
2. Press the ▲▼ buttons to select Repeat, then press the ► button to select
A-B.
3. Press the OK button.
OK
4. Press the OK button at the point where you want the repeat play to start (A),
then press it again at the point where you want the repeat play to stop (B).
Repeat playback of the A-B section starts.
To return to normal playback
Select Off on the Repeat item or press the CANCEL button.
■ If you set point (B) before five seconds has lapsed, the prohibition
mark ( ) will appear.
■ Audio CDs(CD-DA) and MP3 discs do not support the Repeat A-B
function.
English - 42
01403A-R149-XEU-ENG.indb 42
2007-03-09 오후 11:12:00
Selecting the Subtitle Language
DVD-VIDEO
Title
1/2
Chapter
1/28
Time
00:00:01
Subtitle
ENG
Audio
ENG
Repeat
Off
Angle
1/3
Zoom
Off
MOVE
D 5.1CH
Subtitle languages may not work depending on the disc type. This is only
available during playback.
1. Press the ANYKEY button during playback.
CHANGE
2. Press the ▲▼ buttons to select Subtitle, then press the ◄ ► buttons to
select the desired subtitle language.
■ If the subtitles overlap, disable the caption function on your TV.
■ Some discs allow you to select the language for the disc menu only.
■ To make the screen disappear, press the ANYKEY again.
Selecting the Audio Language
DVD-VIDEO
Title
1/2
Chapter
1/28
Time
00:00:01
Subtitle
Off
Audio
ENG
Repeat
Off
Angle
1/3
Zoom
Off
MOVE
D 5.1CH
Audio languages may not work depending on the disc type. This is only
available during playback.
1. Press the ANYKEY button during playback.
CHANGE
2. Press the ▲▼ buttons to select Audio, then press the ◄ ► buttons to
select the desired audio language.
■ Audio languages may be different depending on the disc type.
■ Some discs allow you to select the audio language for the disc menu
only.
■ To make the screen disappear, press the ANYKEY again.
Playback
Using one Touch button
By pressing the audio button, you can access function directly.
Changing the Camera Angle
DVD-VIDEO
Title
1/2
Chapter
1/28
Time
00:00:01
Subtitle
Off
Audio
ENG
Repeat
Off
Angle
1/3
Zoom
Off
MOVE
D 5.1CH
When a DVD-VIDEO contains multiple angles of a particular scene, you can
select the Angle function. This is only available during playback.
If the disc contains multiple angles, the ANGLE mark appears on the screen.
1. Press the ANYKEY button during playback.
CHANGE
2. Press the ▲▼ buttons to select Angle, then press the ◄ ► or number
buttons to select the desired angle.
■ This function is disc-dependent, may not work on all DVDs.
■ This function does not work when a DVD has not been recorded with
a multi-camera angle system.
■ To make the screen disappear, press the ANYKEY again.
English - 43
01403A-R149-XEU-ENG.indb 43
2007-03-09 오후 11:12:03
Zooming-In
1. Press the ANYKEY button during playback or pause.
2. Press the ▲▼ buttons to select Zoom, then press the OK button.
( ) will be displayed.
3. Press the ▲▼◄ ► buttons to move to the area you want to enlarge.
4. Press the OK button.
normal size 2X 4X
2X
normal size
Using Bookmarks
1 2 - - - - - - - --
Bookmark
(V mode)
This feature lets you bookmark sections of a DVD-VIDEO or DVD-R/-RW
(V mode), so you can quickly find them.
▌Setting Bookmarks
MOVE
PLAY
CLEAR
RETURN
1. Press the MARKER button during playback.
2. Press the OK button when the desired scene appears.
The number 1 is displayed and the scene is memorized.
3. Press the ◄ ► button to move to the next position.
Playback
4. Press the OK button when the desired scene appears.
The number 2 is displayed and the scene is memorized.
• Repeat above to bookmark other positions.
• You can bookmark up to 10 scenes.
■ When the disc tray is opened and then closed, bookmarks will
disappear.
▌Playing back a bookmark
1. Press the MARKER button during playback.
1 2 - - - - - - - --
Bookmark
2. Press the ◄ ► buttons to select a bookmarked scene.
3. Press the OK or PLAY button to start playing from the selected scene.
MOVE
PLAY
CLEAR
RETURN
English - 44
01403A-R149-XEU-ENG.indb 44
2007-03-09 오후 11:12:05
▌Clearing a bookmark
1. Press the MARKER button during playback.
Bookmark
2. Press the ◄ ► buttons to select a bookmarked scene.
1 - - - - - - - - --
3. Press the CANCEL button to delete the selected bookmark.
MOVE
OK
RETURN
Using the Markers
Marker
01 02 -- -- -- -- -- -- -- --
N:2
(VR mode)
▌Setting Markers
1. Press the MARKER button during playback.
MOVE
PLAY
CLEAR
RETURN
2. Press the OK button when the desired scene appears.
The number 01 is displayed and the scene is memorized.
3. Press the ◄ ► button to move to the next position.
4. Press the OK button when the desired scene appears.
The number 02 is displayed and the scene is memorized.
• DVD-RAM/DVD-RW(VR mode) discs have the Marker function instead of
the Bookmark function. The Marker function allows you to mark up to
99 scenes. Since the scenes may be displayed as many different pages,
numbering is necessary. If a disc in use is encoded with Disc Protection,
Markers cannot be set or deleted. Only playback is available.
Marker
01 02 -- -- -- -- -- -- -- --
N:2
▌Playing back a Marker
2. Press the ◄ ► buttons to select a bookmarked scene.
MOVE
Marker
PLAY
CLEAR
RETURN
3. Press the OK or PLAY button to start playing from the selected scene.
• If you press the SKIP( ) button, it moves to the beginning of the marker.
Pressing the button once again within 3 seconds returns to the beginning
of the previous marker.
• If you press the SKIP( ) button, it moves to the next marker.
Playback
1. Press the MARKER button during playback.
01 02 03 04 05 06 07 08 09 10 N : 10
▌Clearing a Marker
1. Press the MARKER button during playback.
Marker
MOVE
01 02 03 04 05 06 07 08 09 -- N : 9
PLAY
CLEAR
2. Press the ◄ ► buttons to select a bookmarked scene.
Press the CANCEL button to delete the selected bookmark.
• When a marker is cleared while DVD-RAM/DVD-RW (VR mode) is playing,
marker numbers will change. For example, if the 7th marker is cleared
after ten markers are registered, the marker numbers after the eighth will
automatically move ahead by one and the 8th marker becomes the 7th.
RETURN
English - 45
01403A-R149-XEU-ENG.indb 45
2007-03-09 오후 11:12:07
Playing back an Audio CD(CD-DA)/MP3
▌Buttons on the Remote Control used for Audio CD
(CD-DA)/MP3 playback
1. ▲▼ : Selects a track (song).
2. ► : Plays the selected track (song).
3. OK button: Plays the selected track (song).
4. SKIP(
) button: Plays the next track.
5. RETURN button: Moves to the folder to which the current song belongs.
(MP3 only)
6. SKIP( ) button: Returns to the beginning of the current track when
pressed during playback. If pressed again, your DVD recorder moves to and
plays the previous track. If you press the this button within three seconds
after playback starts, the previous track will be played.
If you press the this button after three seconds, the current track will be
replayed from the beginning.
7. Press the SEARCH( / ) button:
Fast Play (X2, X4, X8) (Audio CD only)
8. STOP button: Stops a track(song).
9. PLAY/PAUSE button: Plays a track(song) or pauses playback.
10. ANYKEY button: Selects the sub menu on screen display (Repeat or Play
Option).
CD
Music List
01/15
TRACK 1
► 0:00:01
TRACK 1
Playback
CDDA
PLAY MODE
No.
Title
Length
002
003
004
005
006
007
TRACK 1
TRACK 2
TRACK 3
TRACK 4
TRACK 5
TRACK 6
TRACK 7
0:03:50
0:04:00
0:03:49
0:03:47
0:04:29
0:03:44
0:03:44
MOVE
OK
RETURN
EXIT
▌Playing an Audio CD(CD-DA)
1. Insert an audio CD (CD-DA) into the disc tray.
The audio CD menu appears and the tracks (songs) are played automatically.
2. Press the ▲▼ buttons to select the track you want to hear, then press the
OK or ► button.
Audio CD(CD-DA) Screen Elements
CD
Music List
01/15
TRACK 1
► 0:00:01
TRACK 1
CDDA
PLAY MODE
No.
Title
Length
002
003
004
005
006
007
TRACK 1
TRACK 2
TRACK 3
TRACK 4
TRACK 5
TRACK 6
TRACK 7
0:03:50
0:04:00
0:03:49
0:03:47
0:04:29
0:03:44
0:03:44
MOVE
OK
RETURN
EXIT
1. Play mode icon
2. Current track(song)
3. Displays the current play index and total track number.
4. Shows the operating state of a disc and a playback time corresponding to a
portion that is currently played.
5. Displays the track list(song list) and the playing time of each track.
6. Button display.
English - 46
01403A-R149-XEU-ENG.indb 46
2007-03-09 오후 11:12:10
▌Playing back an MP3 Disc
MP3
Music List
SONG01
01/13
No.
SONG01
4.0MB
01/26/2007
002
003
004
005
006
PLAY MODE
MOVE
► 0:00:15
MP3
Title
1. Insert an MP3 Disc into the disc tray.
ROOT
SONG01
SONG02
SONG03
SONG04
SONG05
SONG06
OK
2. Press the ▲▼ buttons to select Disc Navigation, and then press the
OK or ► button.
3. Press the ▲▼ buttons to select Music, then press the OK or ► button.
The MP3 menu appears and the tracks(songs) are played automatically.
RETURN
EXIT
4. Press the ▲▼ buttons to select the track (song) you want to hear, then
press the OK or ► button.
MP3 Screen Elements
Music List
MP3
01/13
SONG01
No.
► 0:00:15
SONG01
4.0MB
01/26/2007
MP3
PLAY MODE
002
003
004
005
006
MOVE
2. Current track (song)
Title
ROOT
SONG01
SONG02
SONG03
SONG04
SONG05
SONG06
OK
1. Play mode icon
3. Displays the current track(song) information.
4. Shows the operating state of a disc and a playback time corresponding to a
portion that is currently played.
5. Displays the information for the folder and its tracks.
RETURN
EXIT
6. Button display.
▌Repeat Playback of an Audio/MP3 Disc
CD
Music List
TRACK 1
01/15
No.
► 0:00:01
TRACK 1
CDDA
Length
TRACK 1
PLAY MODE
002
TRACK 2
Repeat
:
Off
003
TRACK 3
Play
: Normal
004optionTRACK
4
005
TRACK 5
006
TRACK 6
007
TRACK 7
MOVE
OK
0:03:50
0:04:00
0:03:49
0:03:47
0:04:29
0:03:44
0:03:44
RETURN
EXIT
1. During playback, press the ANYKEY button.
The Repeat mode will be highlighted.
2. Press the ◄ ► buttons to select the desired repeat mode you want to play
repeatedly, then press the OK button.
•
Repeat Track (CD (CD-DA)/MP3)
•
Repeat Folder (MP3)
•
Repeat Disc (CD (CD-DA)/MP3)
- To return to normal playback -
Playback
PLAY MODE
Title
3. Press the CANCEL button to return to normal playback.
English - 47
01403A-R149-XEU-ENG.indb 47
2007-03-09 오후 11:12:14
▌Play Option Mode
Music List
CD
TRACK 1
01/15
No.
0:00:20
TRACK 1
CDDA
Title
TRACK 1
PLAY MODE
002
TRACK 2
Repeat : Off
003
TRACK 3
Play option
: TRACK
Normal4
004
005
TRACK 5
006
TRACK 6
007
TRACK 7
PLAY MODE
MOVE
OK
Length
0:03:50
0:04:00
0:03:49
0:03:47
0:04:29
0:03:44
0:03:44
RETURN
EXIT
1. Press the ANYKEY button in Stop mode. The PLAY MODE window appears.
2. Press the ◄ ► buttons to select the desired item (Normal, Random,
Intro or Playlist) in the Play option, then press the OK button.
• Normal: Tracks on a disc are played in the order in which they were
recorded on the disc.
• Intro[I]: The first 10 seconds of each track will be played. If you want to
listen to the music that you have selected, press the OK or PLAY( )
button.
The play option will be changed to Normal Play. When Intro Play is
completed, Normal Play is performed.
• Playlist: The Playlist playback option allows you to select the order in
which you want tracks to play.
• Random[R]: The Random option plays a disc’s tracks in random order. After
a random list is generated and played completely, another random list is
generated and played. Random Play is continued until the play option is
changed.
▌To Programme Tracks
Music List
CD
TRACK 1
01/15
No.
0:00:20
TRACK 1
CDDA
Title
TRACK 1
PLAY MODE
002
TRACK 2
Repeat : Off
003
TRACK 3
Play option
: TRACK
Normal4
004
005
TRACK 5
006
TRACK 6
007
TRACK 7
PLAY MODE
MOVE
OK
Length
0:03:50
0:04:00
0:03:49
0:03:47
0:04:29
0:03:44
0:03:44
RETURN
EXIT
Playlist
CD
Playback
06/15
CDDA
TRACK 1
001
TRACK 1
CDDA
TRACK 2
002
TRACK 3
CDDA
TRACK 3
003
TRACK 5
CDDA
TRACK 4
004
TRACK 6
CDDA
TRACK 5
CDDA
TRACK 6
CDDA
TRACK 7
CDDA
You can register a maximum of 30 tracks in the playlist.
1. Press the ANYKEY button in Stop mode.
The PLAY MODE window appears.
2. Press the ◄ ► buttons to select Playlist in the Play option.
3. Press the OK button.
The Playlist screen will appear.
Press the ▲▼ buttons to select Tracks in the order in which you want them
to play. Press the OK button to add the selected track to the Playlist.
If you playlisted a wrong track, press the ► button, then press the ▲▼
buttons to select the wrong track, then press the CANCEL button.
4. Press the PLAY(
) button to playback the playlist.
TRACK 8
PLAY MODE
MOVE
OK
EXIT
Playing back a Picture Disc
JPEG
Photo List
JPEG01
01/10
1. Insert a JPEG into the disc tray.
ROOT
JPEG01
JPEG02
JPEG03
JPEG04
JPEG05
JPEG06
JPEG07
Slide Show
MOVE
OK
RETURN
EXIT
2. Press the ▲▼ buttons to select Disc Navigation, and then press the OK or
► button.
3. Press the ▲▼ buttons to select Photo, and then press the OK or ► button.
4. Press the ▲▼◄ ► buttons to select a picture.
• To see the next 8 pictures, press the SKIP( ) button.
• To see the previous 8 pictures, press the SKIP( )button.
English - 48
01403A-R149-XEU-ENG.indb 48
2007-03-09 오후 11:12:17
5-1. If you press the PLAY button, the Slide Show Speed screen will appear.
Press the ◄► buttons to set the slide show speed, then press the OK
button.
5-2. Press the OK button with a picture selected in the Album screen. And
select a display mode (Album screen, Slide show, Rotation or Zoom)
using the ◄► buttons, then press the OK button.
DVD-RW(VR)
Slide Show Speed
Slow
Normal
Fast
• Album screen (
• Slide show (
JPEG01
MOVE
PHOTO
OK
RETURN
• Rotation (
DVD-RW(VR)
• Zoom (
JPEG01
MOVE
PHOTO
OK
RETURN
) : Returns to the Album screen.
) : The DVD Recorder enters slide show mode. Before the
slide show can begin, the picture interval (Slide show
speed) must be set.
) : Each time the OK button is pressed, the picture rotates
90 degrees clockwise.
) : Each time the OK button is pressed, the picture is enlarged
up to 4X(Four times the normal size).
Normal Zoom X2 Zoom X4 Zoom X2 Normal
• Press the ANYKEY button to display the menu bar.
• Press the RETURN button to clear the menu bar.
Playing the Title List
Title List
DVD-RW(VR)
APR/19/2007
1/6
No.
APR/19/2007 12:00 PR12
APR/19/2007
SP
MOVE
OK
Title
01 APR/19/2007
02 APR/19/2007
03 APR/20/2007
04 APR/20/2007
05 APR/21/2007
06 APR/21/2007
Length Edit
12:00
12:30
12:00
12:30
12:00
12:30
RETURN
00:00:21
00:00:03
00:00:15
00:00:16
00:06:32
00:08:16
►
►
►
►
►
►
EXIT
Follow these instructions to play back a scene from the Title List.
1. Press the TITLE LIST button. The Title List screen is displayed.
2. Press the ▲▼ buttons to select an entry you want to play from Title List.
• Press the PLAY button. The selected entry (title) will be played back.
• Press the OK or ► button. The Edit menu is displayed on the right.
(Rename, Delete, Edit, Protection : See pages 50-52)
3. To stop title play, press the STOP button.
To return the title list screen, press the TITLE LIST button.
1. Playback screen for recorded entries.
DVD-RW(VR)
Title List
APR/21/2007
5/6
APR/21/2007 12:00 PR12
APR/21/2007
SP
MOVE
OK
No. Title
01 APR/19/2007
02 APR/19/2007
03 APR/20/2007
04 APR/20/2007
05 APR/21/2007
06 APR/21/2007
Length Edit
12:00 00:00:21 ►
12:30 00:00:03 ►
Play
12:00 00:00:15 ►
Rename
12:30 00:00:16 ►
Delete
12:00 00:06:32 ►
Edit00:08:16 ►
12:30
Protection
RETURN
EXIT
2. Information window for the selected entry:
Title name, recording date, lock status, recording mode
Playback
▌Title List Screen Elements
3. Recorded entry No.
4. Recorded entry title
5. Recording length (i.e., the playing time)
6. Title list edit items
Play : Plays the selected entry.
Rename : Renames the title of a selected entry.
Delete : Deletes the selected entry from the list.
Edit : Deletes a section of titles.
Protection : Locks or unlocks the selected entry.
7. Button display.
■ By pressing the ANYKEY button, you can play desired title.
(See page 42)
■ This may depend on the disc type.
■ DVD-R/DVD-RW(Video) discs have limited editing function.
(See page 28)
English - 49
01403A-R149-XEU-ENG.indb 49
2007-03-09 오후 11:12:21
Editing
This section introduces basic functions of DVD editing and explains both edit
functions for the recording on a disc and edit functions for the entire disc.
• Title List
A title is a section of recorded video and audio. Title List shows a list to help
you select a title. Since the title list consists of the information on stream that
is actually recorded, if one title is deleted, that title cannot be played again.
• Playlist
This refers to a unit of playback, which is made by selecting a desired scene in
the entire Title List.
When one playlist is played, only the scene selected by the user will play and
then stop. Since only the information necessary for playing a desired scene
is included in a playlist, even if that playlist is deleted, the original stream will
not be deleted.
Recording or editing might not be completed if an error, such as a sudden
power failure occurs.
Please be aware that a material that has been damaged is unable to be
retrieved to its original content.
Basic Editing (Title List)
▌Renaming(Labeling) a Title
Rename
DVD-Recorder
DVD-RW(VR)
Sports(A1)
Follow these instructions to rename a title list entry, i.e., to edit the title of a
recorded programme.
1. Press the TITLE LIST button.
The Title List screen is displayed.
Save
Back Space
MOVE
Space
OK
Delete
RETURN
Clear
EXIT
Title List
DVD-RW(VR)
5/6
Sports (A1)
No.
Sports (A1)
APR/21/2007
Editing
SP
MOVE
Title
01 APR/19/2007
02 APR/19/2007
03 APR/20/2007
04 APR/20/2007
05 Sports (A1)
06 APR/21/2007
OK
Length Edit
12:00
12:30
12:00
12:30
00:00:21
00:00:03
00:00:15
00:00:16
00:06:32
12:30 00:08:16
RETURN
►
►
►
►
►
►
EXIT
2. Press the ▲▼ buttons to select an entry you want to rename from the Title
List, then press the OK or ► button.
3. Press the ▲▼ buttons to select Rename, then press the OK button.
The Rename screen is displayed.
4. Press the ▲▼◄ ► buttons to select the desired characters, then press the
OK button.
• Back Space : Deletes the character before the cursor.
• Space : Enters a blank and moves the cursor one forward (to the right).
• Delete : Deletes the character at the cursor position.
• Clear : Deletes all the character inputs.
• Save : Registers the character inputs.
• The maximum number of characters that can be entered is 31. All 31
characters can be displayed by pressing the INFO button twice.
5. Press the ▲▼◄ ► buttons to select Save, then press the OK button.
The changed title name is displayed on the title item of the selected entry.
English - 50
01403A-R149-XEU-ENG.indb 50
2007-03-09 오후 11:12:24
▌Locking (Protecting) a Title
Title List
DVD-RW(VR)
Sports (A1)
5/6
Title Protection :
Follow these instructions to lock an entry to protect it from accidental
deletion.
Sports (A1)
On
APR/21/2007
Off
SP
MOVE
OK
EXIT
RETURN
Title List
DVD-RW(VR)
Sports (A1)
5/6
No.
01
02
03
04
05
06
Sports (A1)
APR/21/2007
SP
MOVE
OK
Title
Drama
Music
Sports
Movie
Sports(A1)
Edu 1
Length Edit
00:00:21 ►
00:00:03 ►
00:00:15 ►
00:00:16 ►
00:06:32 ►
00:08:16 ►
RETURN
1. Press the TITLE LIST button.
The Title List screen is displayed.
2. Press the ▲▼ buttons to select an entry you want to protect in the Title
List, then press the OK or ► button.
3. Press the ▲▼ buttons to select Protection, then press the OK or ► button.
4. Press the ◄ ► buttons to select On, then press the OK button. The key icon
on the information window for the selected entry changes to the locked
status. (
)
EXIT
▌Deleting a Title
Title List
DVD-RW(VR)
Sports (A1)
5/6
No.
01
02
03
04
05
06
Sports (A1)
APR/21/2007
SP
MOVE
OK
Title
Drama
Music
Sports
Movie
Sports(A1)
Edu 1
Length Edit
00:00:21 ►
00:00:03 ►
Play
00:00:15 ►
Rename
00:00:16 ►
Delete
00:06:32 ►
Edit00:08:16 ►
Protection
RETURN
EXIT
Title List
DVD-RW(VR)
Sports (A1)
5/6
Do you want to delete?
(Related playlists
may be deleted.)
Sports (A1)
APR/21/2007
Yes
No
SP
Follow these instructions to delete an entry from the Title List.
1. Press the TITLE LIST button.
The Title List screen is displayed.
2. Press the ▲▼ buttons to select an entry you want to delete in the Title List,
then press the OK or ► button.
3. Press the ▲▼ buttons to select Delete, then press the OK or ► button.
You will be prompted with a confirmation message.
DVD-RAM, DVD-RW(VR mode) : Since Playlist is present, the message “Do
you want to delete? (Related playlists may be deleted.)” is displayed.
DVD-RW(Video mode), DVD-R : Since Playlist is not present, the message “Do
you want to delete?” is displayed.
• The message may depend on the type of disc.
OK
RETURN
EXIT
■ You cannot delete a protected entry.
If you want to delete a protected entry, select "Off" in the Title
Protection menu.
Editing
4. Press the ◄ ► buttons to select Yes, then press the OK button.
MOVE
■ When the Disc Protection has been set to Protected, you cannot delete
titles. (See page 58)
■ Once an entry is deleted from the Title List it cannot be recovered.
■ Once DVD-R, DVD-RW is finalised, it cannot be deleted.
■ With DVD-R, titles are only deleted from the menu however, the Title
remains physically on the disc.
English - 51
01403A-R149-XEU-ENG.indb 51
2007-03-09 오후 11:12:26
▌Deleting a Section of a Title
Edit Title List
DVD-RW(VR)
Title List No. 05
Start
End
(VR mode)
Follow these instructions to delete a section of a Title List entry.
00:00:06
00:00:00
00:00:06
Start
End
Delete
MOVE
OK
Return
RETURN
DVD-RW(VR)
EXIT
Edit Title List
Title List No. 05
Start
End
00:00:06
End
Delete
MOVE
OK
Return
RETURN
DVD-RW(VR)
EXIT
Edit Title List
Title List No. 05
End
Start
Do you want to delete?
(Deleted part will not be restored.)
00:00:05
00:10:15
Yes
Start
End
No
00:10:15
RETURN
EXIT
Delete
MOVE
OK
Edit Title List
Title List No. 05
Start
End
00:00:06
00:00:00
00:00:06
End
Delete
OK
4. Press the OK button at the starting point.
The image and starting point time are displayed in the section deletion
starting point window.
5. Press the OK button at the end point.
The image and end point time are displayed in the Section deletion ending
point window.
6. Press the OK button at the Delete.
The message "Do you want to delete? (Deleted part will not be restored.)" is
displayed.
7. Press ◄ ► buttons to select Yes, then press the OK button.
The selected section has been deleted.
To return to the Title List screen, press the ◄ ► buttons to select Return.
Return
RETURN
EXIT
Edit Title List Screen Elements
1. Playback bar
2. Playtime
3. Section deletion starting point window and time
4. Section deletion end point window and time
• Select the start and end points of the section you want to delete using
the playback related buttons ( , , , , , ).
■ The length of the section to be deleted must be at least 5 seconds
long.
■ End point cannot be marked earlier than start point.
■ The section cannot be deleted when it includes a still picture.
Editing
MOVE
3. Press the ▲▼ buttons to select Edit, then press the OK or ► button.
The Edit Title List screen is displayed.
Return
DVD-RW(VR)
Start
2. Press the ▲▼ buttons to select an entry you want to edit from the Title List,
then press the OK or ► button.
00:10:15
00:10:15
00:10:15
Start
1. Press the TITLE LIST button.
The Title List screen is displayed.
English - 52
01403A-R149-XEU-ENG.indb 52
2007-03-09 오후 11:12:29
Advanced Editing (Playlist)
▌Creating a Playlist
DVD-Recorder
Make Scene
DVD-RW(VR)
(VR mode)
Scene No. 001
Start
End
Title List : 1/6
00:00:10
Follow these instructions to create a new playlist entry from a recorded title.
1. With the DVD Recorder in Stop mode, press the MENU button.
00:00:00
2. Press the ▲▼ buttons to select Playlist, then press the OK or ► button.
00:00:10
Start
End
Make
Return
OK
MOVE
RETURN
DVD-Recorder
EXIT
Make Scene
DVD-RW(VR)
Scene No. 001
Start
End
Title List : 1/6
00:00:10
00:10:00
00:10:00
00:03:10
Start
End
MOVE
Make
Return
OK
RETURN
3. Press the ▲▼ buttons to select New Playlist, then press the OK or ►
button. The Make Scene screen is displayed.
4. Press the OK button at the start point.
• The image and time at the start point are displayed on the Start window.
• The yellow-coloured selection bar moves to the End item.
• Select the starting point of the section from which you want to create a
new scene using the playback related buttons ( , , , , , , ).
5. Press the OK button at the end point.
• The image and end point time are displayed in the End window.
• The yellow-coloured selection bar moves to the Make item.
EXIT
- To make a new playlist Edit Playlist
DVD-RW(VR)
5/5
APR/25/2007
No.
01
02
03
04
05
APR/25/2007 12:00
1 Scene
APR/25/2007 12:00
MOVE
OK
Title
Length Edit
APR/23/2007 12:00 00:00:21
APR/23/2007 12:30 00:00:03
APR/24/2007 12:00 00:00:15
APR/24/2007 12:30 00:00:16
APR/25/2007 12:00 00:00:32
RETURN
►
►
►
►
►
6. Press the OK button at the Make item.
A new Scene will be added to the current Playlist.
A new Make Scene screen is displayed.
■ You can check and see all the scenes on Edit Playlist screen.
■ Repeat steps 1~6 if you want to make a new playlist.
■ Repeat steps 4~6 if you want to make scenes of the playlist.
EXIT
- To return to Edit Playlist menu 7. Press the ◄ ► buttons to select Return, then press the OK button.
The Edit Playlist screen is displayed.
■ You can create up to 99 playlist entries.
■ Depending on the kind of disc, the displayed screen may have a slight
difference.
■ A disc that is recorded on this unit cannot be displayed playlist menu
if EZ REC MODE set to 'On'.
Edit Playlist
DVD-RW(VR)
APR/24/2007
3/5
No.
Title
Length Edit
01 APR/23/2007 12:00 00:00:21 ►
02 APR/23/2007 12:30
Play00:00:03 ►
03 APR/24/2007 12:00
00:00:15 ►
Rename
04 APR/24/2007 12:30
Edit00:00:16
Scene ►
05 APR/25/2007 12:00
00:00:32 ►
Copy
APR/24/2007 12:00
1 Scene
APR/24/2007 12:00
MOVE
Editing
▌Playing Entries in the Playlist
Delete
OK
RETURN
EXIT
(VR mode)
Follow these instructions to play the playlist entries.
1. With the DVD Recorder in Stop mode, press the PLAY LIST button.
The Edit Playlist screen is displayed.
2. Press the ▲▼ buttons to select the title you want to edit from the Playlist,
then press the OK or ► button.
3. Press the ▲▼ buttons to select Play, then press the OK button.
4. Press the STOP button to stop playing.
The screen returns to the Edit Playlist screen.
English - 53
01403A-R149-XEU-ENG.indb 53
2007-03-09 오후 11:12:34
▌Renaming a Playlist Entry
DVD-Recorder
Rename
DVD-RW(VR)
(VR mode)
Dolphin
Follow these instructions to rename a playlist entry, i.e. to edit the title of a
playlist entry.
1. With the DVD Recorder in Stop mode, press the PLAY LIST button.
The Edit Playlist screen is displayed.
Save
Back Space
MOVE
Space
OK
Delete
RETURN
DVD-RW(VR)
Clear
2. Press the ▲▼ buttons to select the title you want to edit from the Playlist,
then press the OK or ► button.
EXIT
Edit Playlist
Dolphin
3/5
No.
Title
Length Edit
01 APR/23/2007 12:00 00:00:21 ►
02 APR/23/2007 12:30 00:00:03 ►
03 Dolphin
00:00:15 ►
04 APR/24/2007 12:30 00:00:16 ►
05 APR/25/2007 12:00 00:00:32 ►
Dolphin
1 Scene
APR/24/2007 12:00
MOVE
OK
RETURN
EXIT
3. Press the ▲▼ buttons to select Rename, then press the OK button.
The Rename screen is displayed.
4. Enter the desired characters using the ▲▼◄ ► buttons.
• Back Space: Deletes the character before the cursor.
• Space: Enters a blank and moves the cursor one forward (to the right).
• Delete: Deletes the character at the cursor position.
• Clear: Deletes all the character inputs.
• Save: Registers the character inputs.
• The maximum number of characters that can be entered is 31. All 31
characters can be displayed by pressing the INFO button twice.
5. Press the ▲▼◄ ► buttons to select Save, then press the OK button.
The changed title is displayed in the title field of the selected playlist entry.
▌Editing a Scene for the Playlist
DVD-Recorder
Edit Scene
DVD-RW(VR)
Scene No.
1/7
(VR mode)
Playlist No. 3
Play
Modify
01 00:00:26
02 00:00:07
03 00:00:04
Move
Add
▼ 04 00:00:03
05 00:00:11
06 00:00:04
OK
RETURN
MOVE
Delete
EXIT
Follow these instructions to edit scenes for a playlist.
1. With the DVD Recorder in Stop mode, press the PLAY LIST button.
The Edit Playlist screen is displayed.
2. Press the ▲▼ buttons to select the title you want to edit from the Playlist,
then press the OK or ► button.
3. Press the ▲▼ buttons to select Edit Scene, then press the OK button.
The Edit Scene screen is displayed.
Edit Scene
DVD-Recorder
Editing
DVD-RW(VR)
Scene No. 2 / 7
Playlist No. 3
Play
Modify
01 00:00:26
02 00:00:07
03 00:00:04
Move
Add
▼ 04 00:00:03
MOVE
05 00:00:11
06 00:00:04
OK
RETURN
Delete
Playing a Selected Scene
4. Press the ▲▼◄ ► buttons to select the scene you want to play, then press
the OK button.
The playlist entry to be played is selected.
5. Press the OK button.
The selected scene is played.
• To stop scene play, press the STOP button.
EXIT
English - 54
01403A-R149-XEU-ENG.indb 54
2007-03-09 오후 11:12:39
Modifying a Scene (Replacing a Scene)
Follow steps 1 to 3 in page 54.
DVD-Recorder
Edit Scene
DVD-RW(VR)
Scene No.
2/7
Playlist No. 3
Play
Modify
01 00:00:26
02 00:00:07
03 00:00:04
▼ 04 00:00:03
05 00:00:11
06 00:00:04
OK
RETURN
Move
Add
MOVE
Delete
EXIT
Modify Scene
DVD-Recorder
DVD-RW(VR)
Scene No. 002
Start
End
Title List : 5/6
00:00:25
4. Press the ▲▼◄ ► buttons to select the scene you want to modify, then
press the OK button.
5. Press the ▲▼ buttons to select Modify, then press the OK button.
The Modify Scene screen is displayed.
6. Press the OK button at the start point of the scene.
• The image and starting point time are displayed on the Start window.
• Select the starting or ending point of the section you want to modify using
the playback related buttons ( , , , , , , ).
7. Press the OK button at the end point of the scene.
• The image and ending point time are displayed in the End window.
8. Press the ◄ ► buttons to select Change, then press the OK button.
• The scene you want to modify is changed with the selected section.
00:00:00
00:00:25
Start
End
Change
MOVE
OK
Cancel
RETURN
EXIT
Modify Scene
DVD-Recorder
DVD-RW(VR)
Scene No. 002
Start
End
Title List : 5/6
00:00:25
00:00:30
00:00:30
Start
End
Change
MOVE
OK
Cancel
RETURN
DVD-Recorder
EXIT
Edit Scene
DVD-RW(VR)
Scene No.
2/7
Playlist No. 3
Play
Modify
01 00:00:26
02 00:00:05
03 00:00:04
▼ 04 00:00:03
05 00:00:11
06 00:00:04
OK
RETURN
Move
Add
MOVE
Delete
EXIT
Moving a Scene (Changing the Position of a Scene)
DVD-Recorder
Edit Scene
DVD-RW(VR)
Scene No.
3/7
Playlist No. 3
Play
Modify
01 00:00:26
02 00:00:07
03 00:00:04
Move
Add
05 00:00:11
06 00:00:04
OK
RETURN
MOVE
DVD-Recorder
Delete
EXIT
Playlist No. 3
Play
Modify
01 00:00:26
02 00:00:07
03 00:00:03
04 00:00:11
05 00:00:04
06 00:00:04
OK
RETURN
Move
Add
MOVE
5. Press the ▲▼ buttons to select Move, then press the OK button.
• A yellow selection window is displayed on the scene to be moved.
6. Press the ▲▼◄ ► buttons to select the position to which you want to
move the selected scene, then press the OK button.
• The selected scene is moved to the selected position.
Edit Scene
DVD-RW(VR)
Scene No. 5 / 7
▼
4. Press the ▲▼◄ ► buttons to select the scene you want to move (change
the position), then press the OK button.
Editing
▼ 04 00:00:03
Follow steps 1 to 3 in page 54.
Delete
■ You cannot move the selected scene to the position of the next scene,
because the selected scene should be inserted before that position,
which requires no action.
■ Depending on the kind of disc, the displayed screen may have a slight
difference.
EXIT
English - 55
01403A-R149-XEU-ENG.indb 55
2007-03-09 오후 11:12:42
Adding a Scene
DVD-Recorder
Edit Scene
DVD-RW(VR)
Scene No.
4/7
Playlist No. 3
Play
Modify
01 00:00:26
02 00:00:07
03 00:00:04
▼ 04 00:00:03
05 00:00:11
06 00:00:04
OK
RETURN
Move
Add
MOVE
DVD-Recorder
Delete
EXIT
Add Scene
DVD-RW(VR)
Scene No. 004
Start
End
Title List : 4/6
00:00:15
00:00:00
00:00:35
00:00:15
Start
End
Add
MOVE
OK
Cancel
RETURN
EXIT
Follow steps 1 to 3 in page 54.
4. Press the ▲▼◄ ► buttons to select the scene that will have a new scene
inserted before it, then press the OK button.
A yellow selection window is displayed on the scene to be added as the new
scene.
5. Press the ▲▼ buttons to select Add, then press the OK button.
6. Press the OK button at the starting point of the scene.
• The image and starting point time are displayed on the Start window.
• Select the end point of the section where you want to add the new scene
using the playback related buttons ( , , , , , , ).
7. Press the OK button at the end point of the scene.
• The image and time of the end point are displayed in the End window.
• To cancel, press the ◄►buttons to select cancel, then press the OK
button.
8. Press the ◄ ► buttons to select Add, then press the OK button.
• The section you want to add is inserted prior to the scene selected in step 4.
Add Scene
DVD-Recorder
DVD-RW(VR)
Scene No. 004
Start
End
Title List : 4/6
00:00:15
■ You can create up to 999 scenes on one disc. In some cases, this may
be different from the actual numbers.
00:00:35
00:00:35
Start
End
Add
MOVE
OK
Cancel
RETURN
EXIT
Edit Scene
DVD-Recorder
DVD-RW(VR)
Scene No.
4/8
Playlist No. 3
Play
Modify
01 00:00:26
02 00:00:07
03 00:00:04
▼ 04 00:00:20
05 00:00:03
06 00:00:11
OK
RETURN
Move
Add
MOVE
Delete
EXIT
Deleting a Scene
DVD-Recorder
Edit Scene
Follow steps 1 to 3 in page 54.
DVD-RW(VR)
Scene No.
2/6
Playlist No. 3
Play
Modify
01 00:00:26
02 00:00:07
03 00:00:04
Move
4. Press the ▲▼◄ ► buttons to select the scene you want to delete, then
press the OK button.
5. Press the ▲▼ buttons to select Delete, then press the OK button.
Editing
Add
04 00:00:03
05 00:00:11
06 00:00:04
OK
RETURN
MOVE
DVD-Recorder
Delete
EXIT
Edit Scene
DVD-RW(VR)
Scene No.
2/6
Playlist No. 3
Play
Modify
01 00:00:26
02 00:00:04
03 00:00:03
04 00:00:11
05 00:00:04
06 00:00:05
OK
RETURN
Move
Add
MOVE
Delete
EXIT
English - 56
01403A-R149-XEU-ENG.indb 56
2007-03-09 오후 11:12:49
▌Copying a Playlist Entry to the Playlist
Edit Playlist
DVD-RW(VR)
Dolphin
3/4
No.
01
02
03
04
Dolphin
Title
Science
Sky
Dolphin
Natural
7 Scene
Length Edit
00:00:17 ►
00:00:06 ►
Play
00:00:06 ►
Rename
00:00:37 ►
Edit Scene
Copy
APR/23/2007 06:43
Delete
OK
MOVE
2. Press the ▲▼ buttons to select the title you want to copy to the Playlist,
then press the OK or ► button.
3. Press the ▲▼ buttons to select Copy, then press the OK button.
Playlist that has been selected will be copied.
EXIT
RETURN
DVD-RW(VR)
1. With the DVD Recorder in Stop mode, press the PLAY LIST button.
The Edit Playlist screen is displayed.
Edit Playlist
Dolphin
5/5
Dolphin
7 Scene
No.
Title
01
02
03
04
05
Science
Sky
Dolphin
Natural
Dolphin
Length Edit
00:00:17
00:00:06
00:00:06
00:00:37
00:00:06
►
►
►
►
►
APR/23/2007 06:43
MOVE
OK
RETURN
EXIT
▌Deleting a Playlist Entry from the Playlist
Edit Playlist
DVD-RW(VR)
Dolphin
5/5
Do you want to delete?
1. With the DVD Recorder in Stop mode, press the PLAY LIST button.
The Edit Playlist screen is displayed.
2. Press the ▲▼ buttons to select the title you want to delete from the Playlist,
then press the OK or ► button.
3. Press the ▲▼ buttons to select Delete, then press the OK button.
Yes
Dolphin
7 Scene
APR/23/2007 06:43
MOVE
OK
No
RETURN
4. Press the ◄ ► buttons to select Yes, then press the OK button.
It automatically returned to the Edit Playlist screen after the delete operation
has finished.
EXIT
Disc Manager
▌Editing the Disc Name
DVD-Recorder
Rename
DVD-RW(VR)
Follow these instructions to give a name to a disc.
Disc
1. With the DVD Recorder in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Disc Manager, then press the OK or ►
button.
Save
Back Space
Space
OK
MOVE
Delete
EXIT
Disc Manager
DVD-RW(VR)
Title List
Disc Name : Disc
►
Playlist
Disc Protection : Not Protected
►
Disc Manager
Disc Format
►
Programme
Disc Finalise
►
Delete All Title Lists
►
Setup
MOVE
OK
: DVD-VR
RETURN
EXIT
4. Enter the desired characters using the ▲▼◄ ► buttons.
• Back Space : Deletes the character before the cursor.
• Space : Enters a blank and moves the cursor one forward (to the right).
• Delete : Deletes the character at the cursor position.
• Clear : Deletes all the character inputs.
• Save : Registers the character inputs.
• The maximum number of characters that can be entered is 31. All 31
characters can be displayed by pressing the INFO button twice.
Editing
DVD-Recorder
3. Press the ▲▼ buttons to select Disc Name, then press the OK or ► button.
The Edit Name screen is displayed.
Clear
RETURN
5. Press the ▲▼◄ ► buttons to select Save, then press the OK button.
A disc name is given to the disc.
■ You may need to clear disc protect before beginning editing.
■ Depending on the kind of disc, the displayed screen may be different.
English - 57
01403A-R149-XEU-ENG.indb 57
2007-03-09 오후 11:12:56
▌Disc Protection
Disc Manager
DVD-Recorder
DVD-RW(VR)
Title List
Disc Name :
Playlist
Disc Protection : Protected
►
Disc Manager
Disc Format
►
Programme
Disc Finalise
►
Delete All Title Lists
►
Setup
OK
MOVE
►
: DVD-VR
RETURN
Disc Protection allows you to protect your discs from being formatted or
deleted due to unintended operations.
1. With the DVD Recorder in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Disc Manager, then press the OK or ►
button.
EXIT
3. Press the ▲▼ buttons to select Disc Protection, then press the OK or ►
button.
4. Press the ▲▼ button to select Protected, then Press the OK button.
▌Formatting a Disc
DVD-RAM
DVD-Recorder
Disc Manager
DVD-RAM(VR)
Title List
Disc Name :
►
Playlist
Disc Protection : Not Protected
►
Format : DVD-VR
Disc Manager DoDisc
you want to format disc?
Programme Disc Finalize
►
►
Delete
Yes All Title Lists
No
Setup
OK
MOVE
►
DVD-RW
DVD-Recorder
Disc Manager
DVD-RW(VR)
Title List
Disc Name :
►
Playlist
Disc Protection : Not Protected
►
Disc Format : DVD-VR
Disc Manager
Choose the recording format for DVD-RW.
►
Programme
Disc Finalize
►
Setup
Delete
All Title Lists
DVD-VR
DVD-V
►
OK
MOVE
DVD-Recorder
Disc Manager
Editing
DVD-RW(VR)
Title List
Disc Name :
►
Playlist
Disc Protection : Not Protected
►
Disc Manager
All data
will :be
deleted.
Disc
Format
DVD-VR
Do
you
want to continue?
Disc
Finalize
►
Programme
Setup
MOVE
Yes
OK
DVD-RAM
• You will be prompted with the confirmation message “Do you want to format
disc?”.
• If you select Yes using the ◄ ► buttons and press the OK button, you will be
prompted with the confirmation message “All data will be deleted.
Do you want to continue?”.
DVD-RW
• You will be prompted with the confirmation message “Choose the recording
format for DVD-RW.”.
Press the ◄ ► buttons to select desired mode, then press the OK button.
EXIT
RETURN
1. With the DVD Recorder in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Disc Manager, then press the OK or ►
button.
3. Press the ▲▼ buttons to select Disc Format, then press the OK or ►
button.
EXIT
RETURN
Use these instructions to format a disc.
The disc protect should also be cleared.
• You will be prompted again with the message “All data will be deleted.
Do you want to continue?”.
4. Press the ◄ ► buttons to select Yes, then press the OK button.
The disc is formatted.
►
No
RETURN
EXIT
DISC
DVD-VR
DVD-V
DVD-RAM
DVD-RW
DVD-RW
DVD-R
DVD-VR and DVD-V are defined according to their recording format.
English - 58
01403A-R149-XEU-ENG.indb 58
2007-03-09 오후 11:12:59
▌Finalising a disc
Disc Manager
DVD-Recorder
DVD-RW(VR)
Title List
Disc Name :
►
Playlist
Disc Protection : Not Protected
►
Disc Manager
Disc
Format
Do you
want to :fiDVD-VR
nalise disc?
►
Programme
Disc Finalise
►
DeleteYes
All Title Lists No
►
Setup
OK
MOVE
RETURN
After you record titles onto a DVD-RW/-R disc with your DVD recorder, it
needs to be finalised before it can be played back on external devices.
1. With the DVD Recorder in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Disc Manager, then press the OK or ►
button.
3. Press the ▲▼ button to select Disc Finalise, then press the OK or ►
button.
EXIT
4. Press the ◄ ► buttons to select Yes, then press the OK button.
You will be prompted again with the message “Disc will be finalised. Do you
want to continue?”.
5. Press the ◄ ► buttons to select Yes, then press the OK button.
The disc is finalised.
■ Once a disc is finalised, you cannot delete entries from the record list.
■ After being finalised, the DVD-R/DVD-RW(video mode) operates in the
same manner as a DVD-Video.
■ Depending on the disc type, the displayed screen may be different.
■ Finalising time may be different depending on the amount of data
recorded on the disc.
■ Data on the disc will be damaged if the recorder is powered off during
finalise process.
■ You can finalise automatically using EZ REC MODE. (see page 37)
▌Unfinalising a disc (V/VR mode)
DVD-Recorder
Disc Manager
DVD-RW(VR:F)
Title List
Disc Name : Disc
►
1. With the DVD Recorder in Stop mode, press the MENU button.
Playlist
Disc Format : DVD-VR
►
2. Press the ▲▼ buttons to select Disc Manager, then press the OK or ►
button.
Disc
Unfi
nalise
Disc Manager Do
you
want
to unfinalise disc?
►
Programme
Setup
MOVE
Yes
OK
No
RETURN
EXIT
3. Press the ▲▼ button to select Disc Unfinalise, then press the OK or ►
button.
You will be prompted with the message “Do you want to unfinalise disc?”.
4. Press the ◄ ► buttons to select Yes, then press the OK button.
You will be prompted again with the message “Disc will be unfinalised. Do
you want to continue?”.
5. Press the ◄ ► buttons to select Yes, then press the OK button.
The disc is unfinalised.
Mark
Finalise
DVD-Video(RW)
Operation
Same as DVD-Video
Unfinalise
DVD-RW(V)
Additional recording, protection
and deletion are possible.
Editing
■ A DVD-RW can be finalised or unfinalised in Video mode.
■ A DVD-RW can be finalised or unfinalised in VR mode.
Finalise
DVD-RW(VR:F)
Additional recording,
Operation
deletion, editing, and
protection are impossible.
Mark
Unfinalise
DVD-RW(VR)
Additional recording,
deletion, editing, and
protection are possible.
English - 59
01403A-R149-XEU-ENG.indb 59
2007-03-09 오후 11:13:01
▌Delete All Title Lists
Disc Manager
DVD-Recorder
DVD-RW(VR)
Title List
Disc Name :
►
Playlist
Disc Protection : Not Protected
►
Disc
Format
: DVD-VR
Disc Manager
Do you
want
to delete
all title lists?
►
Programme Disc Finalize
►
Setup
OK
RETURN
►
EXIT
Editing
MOVE
Delete
Yes All Title ListsNo
1. With the DVD Recorder in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Disc Manager, then press the OK or ►
button.
3. Press the ▲▼ button to select Delete All Title Lists, then press the OK or
► button.
• When Protected Entry exists : The Delete All Title List function will not
operate. If there is a title containing a still picture, however, that function
will not operate. If you want to delete a protected entry, disable Protect for
it on the Lock item.
4. Press the ◄ ► buttons to select Yes, then press the OK button.
All title lists are deleted.
English - 60
01403A-R149-XEU-ENG.indb 60
2007-03-09 오후 11:13:03
Additional Information
icon appears on the screen.
Troubleshooting
Checkpoint 1
If your DVD Recorder malfunctions, go through the
checkpoints below before contacting a Samsung authorised
service centre.
▌Power
The input is displayed for a while when the power is turned
on.
Checkpoint 1
The DVD recorder requires some time to
initialise and the input will be displayed for
approx. 10 seconds after it is turned on.
▌Recording
Play mode settings are different from the settings configured
in the Settings menu.
Checkpoint 1
The disc does not support all selected
functions. In this case, some settings
configured in the settings menu may not
work properly.
Cannot change the aspect ratio.
Cannot record TV programmes.
Checkpoint 1
Checkpoint 1
Check whether the power cord is securely
plugged into the power outlet.
Checkpoint 2
Did you set the DVD recorder channel settings
correctly?
Checkpoint 3
You cannot use this operation or function due
to one of the following reasons:
(1) Your DVD disc restricts it.
(2) Your DVD disc does not support this
feature (for example: angles)
(3) The feature is not available at the moment.
(4) You've requested a title, chapter, or scan
time that is out of range.
The aspect ratio is fixed for DVD discs.
(See page 25)
The angle operation does not work while playing a DVD disc.
Checkpoint 1
Check the free space on your DVD-RAM/
DVD-RW/DVD-R discs.
The angle operation is available only when
the disc contains images captured from
different angles.
The selected audio and/or subtitle language is not played.
I pressed the REC button but there is no response.
Checkpoint 1
Checkpoint 1
Recording is possible for DVD-RAM/
DVD-RW/DVD-R discs only.
If a programme is copy protected, it cannot
be recorded.
Audio and subtitle languages are disc-specific.
Only the sound and subtitle languages
contained on the DVD disc are available and
displayed in the disc menu.
▌Video
▌Playback
The disc revolves, but no image or bad quality images are
displayed.
Cannot play the disc.
Check whether the disc is inserted correctly
with the label facing up.
Checkpoint 1
Be sure that the Video Setting is properly set.
(See pages 25-26)
Checkpoint 2
Check the regional code of the DVD disc.
Checkpoint 2
Checkpoint 3
This DVD recorder cannot play some types of
discs. (See pages 5, 38.)
Check whether there is damage to or any
foreign material on your disc.
Checkpoint 3
Some low quality discs may not play properly.
Checkpoint 4
If scenes change from dark to bright suddenly,
the screen may shake vertically temporarily,
but this is not a fault.
Additional Information
Checkpoint 1
English - 61
01403A-R149-XEU-ENG.indb 61
2007-03-09 오후 11:13:04
▌Sound
▌Other
No sound.
I forgot my password for parental supervision.
Checkpoint 1
Are you watching a programme in slow or
skip mode?
If you are playing a programme at a speed
other than normal or fast 1 speed, sound will
not be heard.
Checkpoint 2
Check the connections and settings.
(See pages 18, 24-25)
Checkpoint 3
Check whether the disc is damaged.
Clean the disc, if necessary.
Checkpoint 4
Check whether the disc is inserted correctly
with the label facing up.
Check whether you have selected the correct
digital output options in the Audio Output
Options menu.
(See pages 24-25.)
▌Timer Recording
Check there is enough space in the disc for
recording.
Checkpoint 2
Check whether the current disc is recordable
or not.
Make sure to check before the start time of
recording.
A recorded disc is played with only the
subtitle and the audio signal which were
selected during recording.
Other problems.
Checkpoint 1
Read the table of contents and then find and
read the section describing your problem,
follow the instructions given.
Checkpoint 2
Turn your DVD recorder off and on.
Checkpoint 3
If the problem still persists, contact a nearby
Samsung service centre.
Timer lamp flickers.
Checkpoint 1
Press and hold down the STOP ( ) button
on the front panel of the DVD Recorder
simultaneously for more than 5seconds with
no disc in the DVD Recorder. All settings
including the password will revert to the
factory settings.
Do not use this unless absolutely necessary.
(Note that this function is possible only when
no disc is inserted.)
Is it possible to change a subtitle and an audio signal on a
recorded disc?
Checkpoint 1
No audio output.
Checkpoint 1
Checkpoint 1
Timer recording does not work properly.
Checkpoint 1
Re-check the recording time and the end time
settings again.
Checkpoint 2
Recording will be cancelled if the power is
interrupted due to a power failure or another
similar reason while recording.
▌Remote Control Unit
Additional Information
The remote control doesn't work.
Checkpoint 1
Point the remote control at the remote control
sensor on your DVD recorder.
Allow for proper distance. Remove obstacles
between your DVD recorder and the remote
control.
Checkpoint 2
Check whether the batteries are empty.
Checkpoint 3
Check for the TV or DVD selection button.
English - 62
01403A-R149-XEU-ENG.indb 62
2007-03-09 오후 11:13:05
Specifications
Power requirements
AC 220-240V, 50Hz
Power consumption
19 Watts
Weight
2,6 kg
General
Dimensions
430mm(W) x 240mm(D) x 49mm(H)
Operating temp.
+5°C to +35°C
Other conditions
Keep level when operating. Less than 75% operating humidity
Video
Composite Video : 1,0 V p-p at 75Ω load, sync negative
Audio
Max.Audio Input Level : 2Vrms
Input
Receivable Channels
Scart Jack
PAL-I
AV2 (Scart Ext) Video : Composite, RGB Audio: analogue
Analogue output jacks x 2
Audio
Optical/Coaxial digital audio output
Composite Video : Video output jack x 1
Output
Video
S-Video output x 1 (Y:1,0Vp-p, C:0,286Vp-p at 75Ω load)
Component output x 1 (Y: 1,0Vp-p, Pb: 0,70Vp-p, Pr: 0,70Vp-p at 75Ω load)
Scart Jack
AV1 (Scart TV) Video : Composite, RGB Audio: analogue
Picture Compression format
MPEG-II
Audio Compression format
Dolby Digital 2ch/256Kbps, MPEG-II
Recording
XP (about 8 Mbps), SP (about 4 Mbps), LP (about 2 Mbps),
Recording Quality
EP (about 1,2 Mbps or about 0,8 Mbps)
Audio Frequency Response
Audio Output
20 Hz ~ 20 kHz
For DVD discs, audio signals recorded at 96kHz sampling
frequency are converted and output at 48kHz.
Disc Type
DVD
AUDIO CD(CD-DA)
Analogue Audio Output
48 / 96kHz
44,1kHz
Digital Audio Output
48kHz
44,1kHz
Additional Information
English - 63
01403A-R149-XEU-ENG.indb 63
2007-03-09 오후 11:13:07
UNITED KINGDOM
This Samsung product is warranted for the period of
twelve (12) months from the original date of
purchase, against defective materials and
workmanship. In the event that warranty service is
required, you should return the product to the retailer
from whom it was purchased.
However, Samsung Authorised Dealers and
Authorised Service Centres in other EC Countries will
comply with the warranty on the terms issued to
purchasers in the country concerned.
In case of difficulty, details of our Authorised Service
Centres are available from:
Samsung Electronics U.K. Ltd.
Customer Care Centre
PO Box 17243
Edinburgh, EH11 4YB
United Kingdom
Tel : 0870 SAMSUNG (7267864),
Fax : 0870 7221127 (United Kingdom)
Tel : 0818 717 100,
Fax : +44 (0)870 7221127 (Republic of Ireland)
Web : www.samsung.com/uk
WARRANTY CONDITIONS
1. The warranty is only valid if, when warranty service
is required, the warranty card is fully and properly
completed and is presented with the original invoice
or sales slip or confirmation, and the serial number
on the product has not been defaced.
2. Samsung’s obligations are limited to the repair or,
at its discretion, replacement of the product or the
defective part.
3. Warranty repairs must be carried out by Authorised
Samsung Dealers or Authorised Service Centres.
No re-imbursement will be made for repairs carried
out by non Samsung Dealers and, any such repair
work and damage to the products caused by such
repair work will not be covered by this warranty.
01403A-R149-XEU-ENG.indb 64
REPUBLIC OF
IRELAND
4. This product is not considered to be defective
in materials nor workmanship by reason that it
requires adaptation in order to conform to national
or local technical or safety standards in force in
any Country other than the one for which the
product was originally designed and manufactured.
This warranty will not cover, and no re-imbursement will be made for such adaptation nor any
damage which may result.
5. This warranty covers none of the following:
a) Periodic check ups, maintenance and repair or
replacement of parts due to normal wear and
tear.
b) Cost relating to transport, removal or installation
of the product.
c) Misuse, including the faiure to use this product
for its normal purposes or incorrect installation.
d) Damage caused by Lightning, Water, Fire, Acts
of God, War, Public Disturbances, incorrect
mains voltage, improper ventilation or any other
cause beyond the control of Samsung.
6. This warranty is valid for any person who legally
acquired possession of the product during the
warranty period.
7. The consumers statutory rights in any applicable
national legislation whether against the retailer
arising from the purchase contract or otherwise
are not affected by this warranty. Unless there is
national legislation to the contrary, the rights under
this warranty are the consumers sole rights and
Samsung, its subsidiaries and distributors shall not
be liable for indirect or consequential loss or any
damage to records, compact discs, videos or audio
taper or any other related equipment or material.
SAMSUNG ELECTRONICS (U.K.) LTD.
2007-03-09 오후 11:13:08
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre.
Region
North America
Country
CANADA
MEXICO
U.S.A
ARGENTINE
BRAZIL
Latin America
CHILE
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
COLOMBIA
BELGIUM
CZECH REPUBLIC
DENMARK
FINLAND
FRANCE
Europe
CIS
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
Republic of Ireland
Switzerland
RUSSIA
KAZAHSTAN
UZBEKISTAN
UKRAINE
LITHUANIA
LATVIA
ESTONIA
AUSTRALIA
CHINA
HONG KONG
INDIA
Asia Pacific
INDONESIA
JAPAN
MALAYSIA
PHILIPPINES
SINGAPORE
THAILAND
TAIWAN
VIETNAM
SOUTH AFRICA
Middle East & Africa
01403A-R149-XEU-ENG.indb 65
U.A.E
Customer Care Center
1-800-SAMSUNG (7267864)
01-800-SAMSUNG (7267864)
1-800-SAMSUNG (7267864)
0800-333-3733
0800-124-421
4004-0000
800-726-7864 (SAMSUNG)
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-7267-864
0-800-100-5303
01-8000112112
02 201 2418
844 000 844
Distributor pro Českou republiku :
Samsung Zrt., česka organizační složka
Vyskočilova 4, 14000 Praha 4
70 70 19 70
030-6227 515
3260 SAMSUNG or
08 25 08 65 65 (€ 0,15/Min)
01805 - 121213 (€ 0,14/Min)
06-80-SAMSUNG (7267864)
800-SAMSUNG (7267864)
0032 (0)2 201 24 18
0900 20 200 88 (€ 0,10/Min)
815-56 480
0 801 801 881
80 8 200 128
0800-SAMSUNG (726786)
902 10 11 30
0771-400 200
0870 SAMSUNG (7267864)
0818 717 100
0800-7267864
8-800-200-0400
8-800-080-1188
8-800-120-0400
8-800-502-0000
8-800-77777
800-7267
800-7267
1300 362 603
800-810-5858, 010-6475 1880
3698 - 4698
3030 8282
1800 110011
0800-112-8888
0120-327-527
1800-88-9999
1800-10-SAMSUNG (7267864)
1800-SAMSUNG (7267864)
1800-29-3232
02-689-3232
0800-329-999
1 800 588 889
0860 7267864 (SAMSUNG)
800SAMSUNG (7267864)
8000-4726
Web Site
www.samsung.com/ca
www.samsung.com/mx
www.samsung.com
www.samsung.com/ar
www.samsung.com/br
www.samsung.com/cl
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com.co
www.samsung.com/be
www.samsung.com/cz
www.samsung.com/dk
www.samsung.com/fi
www.samsung.com/fr
www.samsung.de
www.samsung.com/hu
www.samsung.com/it
www.samsung.lu
www.samsung.com/nl
www.samsung.com/no
www.samsung.com/pl
www.samsung.com/pt
www.samsung.com/sk
www.samsung.com/es
www.samsung.com/se
www.samsung.com/uk
www.samsung.com/uk
www.samsung.com/ch
www.samsung.ru
www.samsung.kz
www.samsung.uz
www.samsung.com/ur
www.samsung.lt
www.samsung.com/lv/index.htm
www.samsung.ee
www.samsung.com/au
www.samsung.com.cn
www.samsung.com/hk
www.samsung.com/in
www.samsung.com/id
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/ph
www.samsung.com/sg
www.samsung.com/th
www.samsung.com/tw
www.samsung.com/vn
www.samsung.com/za
www.samsung.com/mea
2007-03-09 오후 11:13:09
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product should not be mixed with other commercial wastes for disposal.
AK68-01403A
01403A-R149-XEU-ENG.indb 66
2007-03-09 오후 11:13:10