Sony CDX-CA730X Installation Guide
Add to my manuals
4 Pages
Sony CDX-CA730X car audio system offers a range of features for an enhanced in-car entertainment experience. With its built-in FM/AM tuner, you can easily scan and save your favorite radio stations. Enjoy your music collection by connecting your CD or MD changer using the AUX input. The system's powerful amplifier delivers clear and dynamic audio through your car speakers. The RCA pin cord allows for easy connection to external amplifiers, providing even more versatility for your audio setup.
advertisement
▼
Scroll to page 2
of 4
3-237-888-21 (1) 2 A FM/AM Compact Disc Player AUDIO OUT FRONT AUDIO OUT REAR Installation/Connections Instalación/Conexiones 安裝 B 線路連接 BUS AUDIO IN BUS CONTROL IN BUS AUDIO IN Source selector* Selector de fuente* 音源選擇器* BUS CONTROL IN CDX-CA730X * not supplied * no suministrado * 非附送 Sony Corporation © 2002 Printed in Thailand 1 1 2 4 6 5 ×4 3 7 Cautions Connection diagram (3) • This unit is designed for negative earth 12 V DC operation only. • Do not get the wires under a screw, or caught in moving parts (e.g. seat railing). • Before making connections, turn the car ignition off to avoid short circuits. • Connect the yellow and red power input leads only after all other leads have been connected. • Run all earth wires to a common earth point. • Be sure to insulate any loose unconnected wires with electrical tape for safety. 1 To a metal surface of the car Notes on the power supply cord (yellow) • When connecting this unit in combination with other stereo components, the connected car circuit’s rating must be higher than the sum of each component’s fuse. • When no car circuits are rated high enough, connect the unit directly to the battery. 2 3 4 5 ×2 Parts Iist (1) The numbers in the list are keyed to those in the instructions. Equipment used in illustrations (not supplied) Equipo utilizado en las ilustraciones (no suministrado) 插圖中的裝置(非附送) Front speaker Altavoces delanteros 前揚聲器 Rear speaker Altavoces traseros 後揚聲器 Power amplifier Amplificador de potencia 功率放大器 Caution Handle the bracket 1 carefully to avoid injuring your fingers. CD/MD changer Cambiador de CD/MD CD/MD 換碟機 Rotary commander RM-X4S Mando rotativo RM-X4S 旋轉式控制器 RM-X4S Connection example (2) Notes (2-A) • Be sure to connect the earth cord before connecting the amplifier. • If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. Tip (2-B- ) For connecting two or more CD/MD changers, the source selector XA-C30 (optional) is necessary. 6 First connect the black earth lead, then connect the yellow and red power input leads. To the power aerial control lead or power supply lead of aerial booster amplifier Notes • It is not necessary to connect this lead if there is no power aerial or aerial booster, or with a manually-operated telescopic aerial. • When your car has a built-in FM/AM aerial in the rear/side glass, see “Notes on the control and power supply leads.” To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. To the interface cable of a car telephone To the +12 V power terminal which is energised in the accessory position of the ignition key switch Notes • If there is no accessory position, connect to the +12 V power (battery) terminal which is energised at all times. Be sure to connect the black earth lead to it first. • When your car has a built-in FM/AM aerial in the rear/side glass, see “Notes on the control and power supply leads.” To the +12 V power terminal which is energised at all times Be sure to connect the black earth lead to it first. Notes on the control and power supply leads • The power aerial control lead (blue) supplies +12 V DC when you turn on the tuner. • When your car has built-in FM/AM aerial in the rear/side glass, connect the power aerial control lead (blue) or the accessory power input lead (red) to the power terminal of the existing aerial booster. For details, consult your dealer. • A power aerial without relay box cannot be used with this unit. Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition key is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. • Do not connect the earth lead of this unit to the negative (–) terminal of the car. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker wires installed in your car if the unit shares a common negative (–) lead for the right and left speakers. • Do not connect the unit’s speaker cords to each other. 3 RCA pin cord (not supplied) Cable con clavijas RCA (no suministrado) RCA 針型插頭電線(非附送) Supplied with XA-C30 Suministrado con el XA-C30 附帶於 XA-C30 Source selector (not supplied) Selector de fuente (no suministrado) 音源選擇器(非附送) XA-C30 Supplied with the CD/MD changer Suministrado con el cambiador de CD/MD 附帶於 CD/MD 換碟機 BUS CONTROL IN AUDIO OUT FRONT BUS AUDIO IN REMOTE IN L from car aerial de la antena de automóvil 來自汽車天線 R BUS AUDIO AUDIO OUT AUDIO OUT REAR FRONT AUDIO OUT REAR Insert with the cord upwards. Insertar con el cable hacia arriba. 電線向上插入。 Fuse (10 A) Fusible (10 A) 保險絲(10 A) 7 3 Left Izquierdo 左 AMP REM Blue/white striped Con raya azul/blanca 藍 白條紋 Max. supply current 0.3 A Corriente máx. de alimentación de 0,3 A 最大源電流 0.3 A White Blanco 白色 Right Derecho 右 Left Izquierdo 左 Right Derecho 右 Grey Gris 灰色 Green Verde 緣色 Purple violeta 紫色 Tenga mucho cuidado al manipular el soporte 1 para evitar posibles lesiones en los dedos. Ejemplo de conexiones (2) Notas (2-A) • Asegúrese de conectar primero el cable de puesta a masa antes de realizar la conexión al amplificador. • Si conecta un amplificador de potencia opcional y no utiliza el incorporado, los pitidos se desactivarán. Sugerencia (2-B- ) Cuando desee conectar dos o más cambiadores CD/ MD, necesitará un selector de fuente XA-C30 (opcional). Red Rojo 紅色 Conecte primero el cable de puesta a masa negro, y después los cables amarillo y rojo de entrada de alimentación. 2 Al cable de control de la antena motorizada o al cable de fuente de alimentación del amplificador de antena Notas • Si no se dispone de antena motorizada ni de amplificador de antena, o se utiliza una antena telescópica accionada manualmente, no será necesario conectar este cable. • Si el automóvil incorpora una antena de FM/AM en el cristal trasero/lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”. 3 Para conectar a AMP REMOTE IN del amplificador de potencia opcional Esta conexión es sólo para amplificadores. La conexión de cualquier otro sistema puede dañar la unidad. 4 Al cable de interfaz de un teléfono para automóvil 5 Al terminal de alimentación de +12 V que recibe energía en la posición de accesorio del interruptor de la llave de encendido Notas • Si no hay posición de accesorio, conéctelo al terminal de alimentación (batería) de +12 V que recibe energía sin interrupción. Asegúrese de conectar primero el cable de puesta a masa negro. • Si el automóvil incorpora una antena de FM/AM en el cristal trasero/lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”. 6 Al terminal de alimentación de +12 V que recibe energía sin interrupción Asegúrese de conectar primero el cable de puesta a masa negro. Notas sobre los cables de control y de fuente de alimentación • El conductor de control de la antena motorizada (azul) suministrará +12 V CC cuando conecte la alimentación del sintonizador. • Si el automóvil dispone de una antena de FM/AM incorporada en el cristal trasero/lateral, conecte el cable de control de antena motorizada (azul) o el cable de entrada de alimentación auxiliar (rojo) al terminal de alimentación del amplificador de antena existente. Para obtener información detallada, consulte a su proveedor. • Con esta unidad no es posible utilizar una antena motorizada sin caja de relé. Conexión para protección de la memoria Si conecta el conductor de entrada amarillo, el circuito de la memoria recibirá siempre alimentación, aunque ponga la llave de encendido en la posición OFF. Notas sobre la conexión de los altavoces • Antes de conectar los altavoces, desconecte la alimentación de la unidad. • Utilice altavoces con una impedancia de 4 a 8 ohmios con la capacidad de potencia adecuada para evitar que se dañen. • No conecte los terminales de altavoz al chasis del automóvil, ni conecte los terminales del altavoz derecho con los del izquierdo. • No conecte el cable de puesta a masa de esta unidad al terminal negativo (–) del altavoz. • No intente conectar los altavoces en paralelo. • Conecte solamente altavoces pasivos. Si conecta altavoces activos (con amplificadores incorporados) a los terminales de altavoz, puede dañar la unidad. • Para evitar fallos de funcionamiento, no utilice los cables de altavoz incorporados instalados en el automóvil si su unidad comparte un cable negativo común (–) para los altavoces derecho e izquierdo. • No conecte los cables de altavoz de la unidad entre sí. 2 4 5 Yellow Amarillo 黃色 6 Purple/black striped Con raya violeta/negra 紫 黑條紋 1 A una superficie metálica del automóvil Precaución ATT Green/black striped Con raya verde/negra 緣 黑條紋 Diagramas de conexión (3) Los números de la lista corresponden a los de las instrucciones. Light blue Azul celeste 淡藍色 ANT REM Max. supply current 0.1 A Corriente máx. de alimentación de 0,1 A 最大源電流 0.1 A Grey/black striped Con raya gris/negra 灰 黑條紋 • Esta unidad ha sido diseñada para alimentarse con 12 V CC, negativo a masa, solamente. • No coloque los cables debajo de ningún tornillo, ni los aprisione con partes móviles (p. ej. los raíles del asiento). • Antes de realizar las conexiones, desactive el encendido del automóvil para evitar cortocircuitos. • Conecte los cables de entrada de alimentación amarillo y rojo solamente después de haber conectado los demás. • Conecte todos los conductores de puesta a masa a un punto común. • Por razones de seguridad, asegúrese de aislar con cinta eléctrica los cables sueltos que no estén conectados. Lista de componentes (1) 1 Blue Azul 藍色 White/black striped Con raya blanca/negra 白 黑條紋 Precauciones Notas sobre el cable de suministro de alimentación (amarillo) • Cuando conecte esta unidad en combinación con otros componentes estéreo, la capacidad nominal del circuito conectado del automóvil debe ser superior a la suma de los fusibles de cada componente. • Si no hay circuitos del automóvil con capacidad nominal suficientemente alta, conecte la unidad directamente a la batería. Black Negro 黑色 注意 線路連接圖(3) • 本機只能使用負極接地 12 V 直流電源。 • 不要使導線夾在螺栓下,或繞掛在移動部件上 (如:座椅扶手上)。 • 連接線路之前,請關閉汽車點火裝置以免引起短 路。 • 黃色和紅色電源輸入導線必須在所有其它導線都 連接完畢以後才連接。 • 將所有地線都連接到同一接地點。 • 為了安全,請確認把沒有連接的導線用電器膠帶 包紮進行絕緣。 1 連接至汽車的金屬表面 電源導線須知(黃色) • 將本機與其它立體聲裝置組合使用時,所連接 的汽車電路容量必須大於每個裝置保險絲容量 的總和。 • 當汽車電路容量不夠大時,請將本機直接與電 池相連接。 零件一覽表(1) 圖示數字與說明書中的數字是一致的。 注意 拿取托架 1 時,請特別注意別傷到手指。 2 3 4 5 6 首先連接黑色接地導線,然後再連接黃色和紅色電源 輸入導線。 連接至電動天線控制導線或天線升壓放大器的電源導線 註 • 如無電動天線,天線升壓器,或有手動套管式天 線,便不須連接此導線。 • 您汽車的後 側玻璃窗中如果有內置 FM/AM 天線, 即請參看“控制線和電源線須知”。 連接至選購的功率放大器的 AMP REMOTE IN(放大器 遙控輸入) 本連接僅用於放大器。連接任何其它系統可能會損壞 本機。 連接至汽車電話的接口電纜 連接至在點火鑰匙開關的附件位置上通電的 +12 V 電 源端子 註 • 若沒有附件位置,則請連接至始終通電的 +12 V 電 源(電池)端子。 務請首先將黑色接地導線與其連接。 • 您汽車的後 側玻璃窗中如果有內置 FM/AM 天線, 即請參看“控制線和電源線須知”。 連接至始終通電的 +12 V 電源端子 務請首先將黑色接地導線與其連接。 控制線和電源線須知 • 接通調諧器電源時,電動天線的控制導線(藍色)便 能提供 +12 V 直流電。 • 若您的汽車後 側玻璃窗上有內置 FM/AM 天線,須將 電動天線控制導線(藍色)或輔助電源輸入導線(紅 色)連接到現有天線升壓器上的電源端子上。詳細內 容請向銷售商諮詢。 • 本機不能使用不具備繼電器盒的電動天線。 保持記憶的線路連接法 當連接好黃色電源輸入導線時,即使汽車發動機點火鑰匙 關閉,電源仍將對記憶電路供電。 線路連接圖例(2) 註(2-A) • 務必在接放大器之前連接地線。 • 如果您連接了選購的功率放大器而不使用內置放大 器,將無提示聲功能。 要領(2-B- ) 若要連接 2 台或更多 CD/MD 換碟機時,必須使用音源選 擇器 XA-C30(選購件)。 連接揚聲器時的注意事項 • 連接揚聲器電線以前,請先關閉本機電源。 • 使用阻抗為 4-8Ω 且具有足夠功率處理容量的揚聲 器,以免損壞揚聲器。 • 不要將揚聲器端子連接到汽車底盤上,或將右揚聲器 端子與左揚聲器端子相連接。 • 切勿將本機的接地導線連接至汽車的負(-)接線端。 • 揚聲器不可並聯連接。 • 請僅連接無源揚聲器。若將有源揚聲器(帶內置放大 器)連接到揚聲器端子上會損壞本機。 • 若本裝置使用左、右揚聲器的共用負極(-)導線,為了 避免故障,切勿使用已安裝在汽車內的內置揚聲器導 線。 • 請勿將本裝置揚聲器導線相互連接。 4 A B c 1 2 5 1 2 3 4 Dashboard Salpicadero 儀表板 Fire wall Panel cortafuegos 防火壁 1 4 4 6 2 5 Bend these claws outward for a tight fit, if necessary. 1 Si es necesario, doble estas uñas hacia fuera para que encaje firmemente. 3 5 若有必要,則可彎曲這些卡爪。 5 4 Precautions Mounting example (5) Precauciones Ejemplo de montaje (5) •Choose the installation location carefully so that the unit will not interfere with normal driving operations. •Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperatures, such as in direct sunlight or near heater ducts. •Use only the supplied mounting hardware for a safe and secure installation. Installation in the dashboard • Elija cuidadosamente el lugar de montaje de forma que la unidad no interfiera las funciones normales de conducción. • Evite instalar la unidad donde pueda quedar sometida a altas temperaturas, como a la luz solar directa o a conductos de calefacción, o a polvo, suciedad o vibraciones excesivas. • Para realizar una instalación segura y firme, utilice solamente la ferretería de montaje suministrada. Instalación en el salpicadero Mounting angle adjustment Note When installing this unit: Depending on car type, the mounting angle may not allow the front panel to open easily. In such a case, remove the silver screw A shown below. When screwing it on again, first lock the lever B. Attaching the screw without doing so may cause the unit to break. Ajuste del ángulo de montaje Adjust the mounting angle to less than 60°. Nota Cuando instale esta unidad: Es posible que el ángulo de montaje (en función del tipo de automóvil) no permita que el panel frontal se abra con facilidad. En tal caso, extraiga el tornillo plateado A mostrado más abajo. Cuando vuelva a atornillarlo, bloquee primero la palanca B. Si fija el tornillo sin realizar lo expuesto, la unidad podría romperse. Ajuste el ángulo de montaje a menos de 60°. B B How to detach and attach the front panel (4) A Before installing the unit, detach the front panel. 4-A To detach Before detaching the front panel, be sure to press (OFF). Press (OPEN), then slide the front panel to the right side, and pull out the left side. 4-B To attach Place the hole in the front panel onto the spindle on the unit as illustrated, then push the left side in. Frequency select switch The AM (FM) tuning interval is factory-set to the 9 k (50 k) position. If the frequency allocation system of your country is based on 10 kHz (200 kHz) interval, set the switch on the bottom of the unit to the 10 k (200 k) position before making connections. Mounting the unit in a Japanese car (6) You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer. Note To prevent malfunction, install only with the supplied screws 4. Warning when installing in a car without ACC (accessory) position on the ignition key switch Be sure to press (OFF) on the unit for two seconds to turn off the clock display after turning off the engine. When you press (OFF) only momentarily, the clock display does not turn off and this causes battery wear. RESET button When the installation and connections are completed, be sure to press the RESET button with a ballpoint pen, etc. Forma de extraer e instalar el panel frontal (4) A Antes de instalar la unidad, extraiga el panel frontal. 4-A Para extraerlo Antes de extraer el panel frontal, asegúrese de pulsar (OFF). Después pulse (OPEN) para abrirlo, deslícelo hacia la derecha, y por último tire de su parte izquierda. 4-B Para instalarlo Coloque el orificio del panel frontal en el eje de la unidad, como se muestra en la ilustración, y después presione la parte izquierda. Selector de frecuencia El intervalo de sintonía de AM (FM) ha sido ajustado en fábrica a la posición 9 k (50 k). Si el sistema de asignación de frecuencias de su país se basa en el intervalo de 10 kHz (200 kHz), coloque este selector, situado en la base de la unidad, en la posición 10 k (200 k) antes de realizar las conexiones. Montaje de la unidad en un automóvil japonés (6) No podrá instalar esta unidad en algunos automóviles japoneses. En tal caso, consulte a su proveedor Sony. Nota Para evitar que se produzcan fallos, realice la instalación solamente con los tornillos suministrados 4. Advertencia sobre la instalación en un automóvil que no disponga de posición ACC (accesorio) en el interruptor de la llave de encendido Asegúrese de pulsar (OFF) en la unidad durante dos segundos para desactivar la indicación del reloj después de apagar el motor. Si pulsa (OFF) sólo momentáneamente, la indicación del reloj no se desactivará y esto causará el desgaste de la batería. Botón RESET Cuando finalice la instalación y las conexiones, asegúrese de pulsar el botón RESET con un bolígrafo, etc. 6 A B TOYOTA NISSAN 4 4 max. size 5 × 8 mm Tamaño máx. 5 × 8 mm 最大尺寸 5×8 mm max. size 5 × 8 mm Tamaño máx. 5 × 8 mm 最大尺寸 5×8 mm to dashboard/center console al salpicadero/consola central 至儀表板 中央控制箱 4 Bracket Soporte 托架 4 max. size 5 × 8 mm Tamaño máx. 5 × 8 mm 最大尺寸 5×8 mm Bracket Soporte 托架 使用前注意事項 安裝示例(5) •仔細選取安裝位置,以使本裝置不干擾正常的駕 駛操作。 •避免將本機安裝在受灰塵,污物和強烈振動影響 的區域,或安裝在高溫處,如直對陽光下或熱氣 管道附近。 •為了安裝安全和可靠,請使用附送的安裝構件。 安裝在儀錶板裡 請在 60 度以內調整安裝角度。 安裝本機時:有些車型的車輛其安裝角度可能 會使機器的前面板不易開啟。此時,請如下面所示 卸下銀螺釘 A。 再旋上螺釘時,請先鎖定操作桿 B。裝螺釘 時不如此作,便可能造成裝置損壞。 B A 安裝本機之前,請先拆卸前面板。 4-A 拆卸 拆卸前面板之前,須先按 (OFF) 。 按 (OPEN) ,然後將前面板滑向右側,再將 左側拉出。 4-B 裝配 如圖所示,將前面板的 上,然後推入左側。 孔搭在本機的支軸 將本機安裝於日本產汽車上時 (6) 有的日本產汽車不能安裝本機,在這種情形下,請 向 Sony 經銷商諮詢。 註 為防止發生故障,安裝時只能使用附送的螺絲 4。 頻率選擇開關 AM(FM)調諧間隔在出廠前被設定在 9 k (50 k)位置上。若貴國的頻率分配系統是基於 10 kHz(200 kHz)間隔,連接前,請將本機底部 上的開關設定在 10 k(200 k)位置上。 max. size 5 × 8 mm Tamaño máx. 5 × 8 mm 最大尺寸 5×8 mm Existing parts supplied with your car Piezas existentes suministradas con su automóvil 隨汽車附送的部件 註 如何拆卸和裝配前面板(4) Bracket Soporte 托架 Bracket Soporte 托架 Existing parts supplied with your car Piezas existentes suministradas con su automóvil 隨汽車附送的部件 安裝角度之調整 to dashboard/center console al salpicadero/consola central 至儀表板 中央控制箱 安裝在點火鑰匙開關上沒有 ACC (附件)位置的汽車上時的警告 在關掉汽車引擎之後,一定請按下裝置上的 (OFF) 兩秒以關掉時鐘顯示。 如果只短暫地按一下 (OFF),將不會關掉時鐘顯 示而浪費電池。 RESET 按鈕 當安裝和連接完成後,務請用原子筆等按壓 RESET 按鈕。
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project