ZANUSSI ZW8F1168MS User Manual

User Manual
GETTING
STARTED?
EASY.
ZW8F1168MS
EN User Manual
Washing Machine
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
•
•
•
•
•
•
•
•
•
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
Children of less than 3 years of age should be kept away from
the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep detergents away from children.
Keep children and pets away from the appliance when the door
is open.
If the appliance has a child safety device, it should be activated.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
•
•
2
Do not change the specification of this appliance.
This appliance is intended to be used in household and similar
applications such as:
– staff kitchen areas in shops, offices and other working
environments;
– by clients in hotels, motels, bed & breakfast and other
residential type environments;
•
•
•
•
•
•
•
•
•
– areas for communal use in blocks of flats or in launderettes.
Do not exceed the maximum load of 10 kg (refer to the
"Programme chart" chapter).
The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8
bar (0.8 MPa).
The ventilation opening in the base must not be covered by a
carpet, mat, or any floor covering.
The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by
the Authorised Service Centre.
Old hose sets must not be reused.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean
the appliance.
Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
SAFETY INSTRUCTIONS
INSTALLATION
The installation must comply with
relevant national regulations.
•
•
•
•
•
•
Remove all the packaging and the transit bolts
including rubber bush with plastic spacer.
Keep the transit bolts in a safe place. If the
appliance is to be moved in the future they must
be reattached to lock the drum to prevent an
internal damage.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Follow the installation instructions supplied with
the appliance.
Do not install or use a damaged appliance.
Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
•
•
•
•
•
•
•
The floor area on which the appliance is to be
installed must be flat, stable, heat resistant and
clean.
Make sure that there is air circulation between
the appliance and the floor.
When the appliance is in its permanent position,
check if it is levelled correctly with the aid of a
spirit level. If it is not, adjust the feet accordingly.
Do not install the appliance directly above a
floor drain.
Do not spray water on the appliance and do not
expose it to excessive humidity.
Do not install the appliance where the appliance
door cannot be fully opened.
Do not put a closed container to collect
possible water leakage under the appliance.
Contact the Authorised Service Centre to
ensure which accessories can be used.
3
ELECTRICAL CONNECTION
USE
WARNING! Risk of injury, electric
shock, fire, burns or damage to the
appliance.
WARNING! Risk of fire and electric
shock.
•
•
•
•
•
•
•
•
•
The appliance must be earthed.
Always use a correctly installed shockproof
socket.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
Do not touch the mains cable or the mains plug
with wet hands.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
This appliance complies with the E.E.C.
Directives.
WATER CONNECTION
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
• Ensure that there are no visible water leaks
during and after the first use of the appliance.
• Do not use an extension hose if the inlet hose is
too short. Contact the Authorised Service
Centre for the replacement of the inlet hose.
• It is possible to see water flowing from the drain
hose. This is due to the testing of the appliance
with the use of water in the factory.
• You can extend the drain hose to maximum 400
cm. Contact the Authorised Service Centre for
the other drain hose and the extension.
INSTALLATION
WARNING! Refer to Safety chapters.
4
•
•
•
•
•
Follow the safety instructions on the detergent
packaging.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Make sure that all metal objects are removed
from the laundry.
Do not wash fabrics which are heavily soiled
with oil, grease or other greasy substances. It
can damage rubber parts of the washing
machine. Prewash such fabrics by hand before
loading them into the washing machine.
Do not touch the glass door while a programme
is in operation. The glass can get hot.
SERVICE
• To repair the appliance contact the Authorised
Service Centre.
• Use original spare parts only.
DISPOSAL
WARNING! Risk of injury or
suffocation.
•
•
•
•
Disconnect the appliance from the mains
electrical and water supplies.
Cut off the mains electrical cable close to the
appliance and dispose of it.
Remove the door catch to prevent children or
pets from becoming trapped in the drum.
Dispose of the appliance in accordance with
local requirements for the disposal of Waste
Electrical and Electronic Equipment (WEEE).
UNPACKING
1. Remove the external film. If necessary, use a cut-
2. Remove the cardboard top and the polystyrene
packaging materials.
ter.
3. Open the door. Remove all the items from the
drum .
4. Put the front polystyrene packaging element on
the floor under the appliance. Carefully put down
the appliance onto its rear side.
5. Remove the polystyrene protection from the bottom. Put the appliance back into an upright position.
6. Remove the power supply cable and the drain
hose from the hose holders.
1
2
It is possible to see water flowing from the drain
hose. This is because the washing machine has
been tested at the factory.
5
7. Remove the three transit bolts and pull out the
plastic spacers.
We recommend that you keep the
packaging and the transit bolts for any
transport of the appliance.
INFORMATION FOR INSTALLATION
Positioning and levelling
Adjust the appliance correctly to prevent vibration,
noise and movement of the appliance when it
operates.
1. Install the appliance on a flat hard floor. The
appliance must be levelled and stable. Make sure
that the appliance does not touch the wall or other
units and there is air circulation below the
appliance.
2. Loosen or tighten the feet to adjust the level. All
feet must rest firmly on the floor.
WARNING! Do not put cardboard,
wood or equivalent materials below
the appliance feet to adjust the level.
The inlet hose
CAUTION! Make sure there is no
damage to hoses and there are no
leaks from the couplings. Do not use
an extension hose if the inlet hose is
too short. Contact the service centre
for a replacement inlet hose.
8. Put the plastic caps, that you find in the user
manual bag, in the holes.
1. Connect the water inlet hose to the back of the
appliance.
45º
20º
2. Position it toward left or right depending on the
positon of the water tap. Make sure that the inlet
hose is not in vertical position.
3. If necessary, loosen the ring nut to set it in the
correct position.
4. Connect the water inlet hose to the cold water
tap with 3/4'' thread.
Water drainage
The drain hose should stay at a height of no less
than 60 cm and not more than 100 cm.
You can extend the drain hose to
maximum 400 cm. Contact the
authorised service centre for the other
drain hose and the extension.
It is possible to connect the drain hose in different
ways:
6
1. Make a U shape with the drain hose and put it
around the plastic hose guide.
illustration.
2. On the edge of a sink - Fasten the guide to the
water tap or to the wall.
The end of the drain hose must always
be ventilated , i.e. the inner diameter of
the drain pipe (min. 38 mm - min. 1.5")
must be larger than the external
diameter of the drain hose.
5.Without the plastic hose guide, to a sink spigotPut the drain hose in the spigot and tighten it with a
clamp. Refer to the illustration.
Make sure that the plastic guide
cannot move when the appliance
drains and the drain hose end is not
immersed in the water. There may be a
return of dirty water into the appliance.
3. If the end of the drain hose looks like this (see
the picture), you can push it directly into the stand
Make
sure that the drain hose makes a loop to prevent
particles going into the appliance from the sink.
6. Position the hose directly to a built-in drain pipe
in the room wall and tighten it with a clamp.
pipe.
4. To a stand pipe with vent-hole - Insert the drain
hose directly into a drain pipe. Refer to the
7
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1
2
8
3
9
10
4
5
11 12
6
7
1 Worktop
2 Detergent dispenser
8 Drain hose
9 Inlet hose connection
3 Control panel
4 Door handle
10 Mains cable
11 Transit bolts
12 Hose support
5 Rating plate
6 Drain pump filter
7 Feet for levelling the appliance
CONTROL PANEL
SPECIAL FEATURES
Your new washing machine meets all modern
requirements for an effective treatment of laundry
with low water, energy and detergent consumption
and proper care of fabric.
• The Family Care technology has been
designed to protect the fabric fibres thanks to
different pre-mixing phases that dissolves first
the detergent and then fabric softener in the
water before they are distributed in the laundry.
So every fibre is reached and cared for.
• The steam has a quick and easy way to refresh
the clothes. The gentle steam programmes
remove odours and reduce creases in dry
fabrics so they need little ironing.
8
•
•
•
The Plus Steam option, finishes every cycle
with gentle steam that relaxes the fibres and
reduces fabric creasing. Ironing will be easier!
The Stain option pre-treats stubborn stains
optimizing the effectiveness of the stain
remover.
Thanks to the Soft Plus option, the fabric
softener is uniformly spread out in the laundry
and deeply penetrates the fabric fibres favouring
a perfect softness.
The AutoAdjust System detects the laundry
load size defining the programme duration in 30
seconds. The washing programme is tailored to
the laundry load and the type of fabric without
consuming more time, energy and water than
necessary.
CONTROL PANEL DESCRIPTION
1
2
3
4
5
6
7
Cotton Flex
Wool/Silk
Cotton
Ultrawash
Temp.
Time
Manager
Spin
Delay
Start
Synthetics
Denim
Delicate
Outdoor
Rapid
14 min
Delicate
Steam
Duvet
Steam Refresh
Rinse
Spin/Drain
Prewash
Stain
Extra Rinse
Soft Plus
Plus
Steam
Silent
11
10
9
8
On/Off
14
1 Programme dial
2 Spin touch button
13 12
9 Plus Steam touch button
10 Soft Plus touch button
11 Extra Rinse touch button
3 Temp. touch button
4 Display
5 Delay Start touch button
12 Stain touch button
13 Prewash touch button
6 Time Manager touch button
14 On/Off push button
7 Start/Pause
touch button
8 Silent touch button
DISPLAY
MIX
9
The Temperature area:
Temperature indicator .
Cold water indicator.
Child safety lock indicator.
Door locked indicator.
Delay start indicator.
The digital indicator can show:
• Programme duration (e. g.
•
Delay time (e. g.
•
Cycle end (
).
).
).
•
Warning code (e.g.
•
Error indicator (
).
).
Time Manager indicator.
MIX
Family Care indicator.
Steam phase indicator.
Anti-crease phase indicator.
Drum clean indicator. This is a recommendation to perform the drum cleaning.
The spin area:
Spin speed indicator
No Spin indicator. Spin phase is off.
Silent indicator.
Rinse Hold indicator.
Add garments indicator. it lights at the beginning of the washing phase,
when it is still possible to pause the appliance and add more laundry.
Maximum load indicator (refer to "The AutoAdjust System load detection "
paragraph).
It flashes when the laundry load exceeds the maximum declared
load of the selected programme.
10
DIAL AND BUTTONS
INTRODUCTION
The options/functions are not available
with all washing programmes. Check
the compatibility between options/
functions and washing programmes in
the "Programme Chart". An option/
function can exclude another one, in
this case the appliance doesn't allow
you to set incompatible options/
functions.
ON/OFF
Press this button for a few seconds to activate or
deactivate the appliance. Two different tunes sound
while switching the appliance on or off.
As the Stand-by function automatically deactivates
the appliance after several minutes to reduce the
energy consumption, you may need to activate the
appliance again.
For more details, refer to Stand-by paragraph in
Daily Use chapter.
TEMP.
When you select a washing programme, the
appliance automatically proposes a default
temperature.
Touch this button repeatedly until the desired
temperature value appears on the display.
When the display shows the indicators
, the
appliance does not heat the water.
SPIN
When you set a programme, the appliance
automatically sets the maximum spin speed
allowed, except for programme Denim. With this
option you can decrease the default spin speed.
Touch repeatedly this button to:
• Decrease the spin speed. The display shows
only the spin speeds available for the set
programme.
•
Additional spin options No Spin
.
Set this option to deactivate all spin phases.
The display shows the indicator
. The
appliance performs the only draining phase of
the selected washing programme. Set this
option for very delicate fabrics. The rinses phase
uses more water for some washing programmes
•
Activate the Rinse Hold
option.
The final spin is not performed. The water of the
last rinse is not drained out to prevent the
fabrics from creasing. The washing programme
ends with water in the drum.
remains on. The door stays
The indicator
locked and the drum turns regularly to reduce
creasing. You must drain the water to unlock the
door.
If you touch the Start/Pause
button, the
appliance performs the spinning phase and
drains the water.
The appliance empties the water
out automatically after 18 hours
approximately.
PREWASH
With this option you can add a prewash phase to a
washing programme.
The corresponding indicator above the touch
button illuminates.
• Use this option to add a pre-wash phase at 30
°C before the washing phase.
This option is recommended for heavily soiled
laundry, especially if containing sand, dust, mud
and other solid particles.
The options can increase the
programme duration.
STAIN
Touch this button to add the stain phase to a
programme.
The corresponding indicator above the touch
button illuminates.
Use this option for laundry with hard stains to
remove.
When you set this option, put the stain remover into
.
compartment
The stain remover is pre-mixed and heated with
detergent in order to improve its effectiveness.
This option increases the programme
duration.
This option is not available with a
temperature lower than 40 °C.
PERMANENT EXTRA RINSE
With this option you can add a few rinses
according to the selected washing programme.
Use this option for people with allergies to
detergent residues and with sensitive skin.
11
This option increases the programme
duration.
The corresponding indicator above the touch
button illuminates and also stays permanently on
during next cycles until this option is deactivated.
PERMANENT SOFT PLUS
Set this option to optimise the fabric softener
distribution and improve fabric softness.
Recommended when you use fabric softener.
This option increases the programme
duration.
The corresponding indicator above the touch
button illuminates and also stays permanently on
during next cycles until this option is deactivated.
PLUS STEAM
This option adds a steam phase followed by a short
anti-crease phase at the end of the washing
programme.
The steam phase reduces fabric creasing and
facilitates the fabric ironing.
The corresponding indicator above the touch
button illuminates.
The indicator
is steady on during steam phase.
This option can increase the
programme duration.
When the programme stops the display shows
, the indicator
goes off and the indicator
is steady on. The drum performs smooth
movements for about 30 minutes to keep the steam
benefit. By touching any button the anti-crease
movements stop and the door unlocks.
A small laundry load helps to reach
better results.
SILENT
Touch this button to activate-deactivate the option
Silent .
The intermediate and the final spinning phases are
suppressed and the programme ends with water in
the drum. This helps to reduce creasing.
The display shows the indicator
. The door stays
locked. The drum turns regularly to reduce
creasing. You must drain the water to unlock the
door.
12
As the programme is very quiet, it is suitable for use
at night time when cheaper electricity tariffs are
available. In some programmes the rinses are
performed with more water.
If you touch the Start/Pause
button, the
appliance performs the only draining phase.
The appliance empties the water out
automatically after 18 hours
approximately.
DELAY START
With this option you can delay the start of a
programme to a more convenient time.
Touch the button repeatedly to set the required
delay. The time increases in steps of 1 hour up to
20 hours.
and the
The display shows the indicator
selected delay time. After touching the Start/Pause
button, the appliance begins the countdown
and the door is locked.
TIME MANAGER
With this option you can reduce the programme
duration depending on the load size and the degree
of soiling.
When you set a washing programme, the display
shows the default duration and
dashes.
Touch Time Manager button to reduce the
programme duration according to your needs. The
display shows the new programme duration and a
number of dashes will decrease accordingly:
suitable for a full load of normally soiled
garments.
a quick cycle for a full load of lightly soiled
garments.
very quick cycle for a smaller lightly soiled
load (max. half load recommended).
the shortest cycle to freshen up a small
amount of laundry.
The Time Manager is available only with the
programmes in the table.
1)
Synthetics
Cotton
Cotton Flex
indicator
Time Manager with steam programmes
When setting a steam programme, this button
allows to chose three steam levels and the
programme duration is reduced accordingly:
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
•
: maximum.
•
: medium.
•
: minimum.
In some appliances the programme
duration is reduced without showing
any dashes.
START/PAUSE
Touch the Start/Pause
button to start, pause
the appliance or interrupt a running programme.
1) Default duration for all programmes.
PROGRAMMES
PROGRAMME CHART
Programme
Reference
Default temperaspin speed Maximum
ture
Spin speed
load
Temperature
range
range
Programme description
(Type of load and soil level)
Washing programmes
Cotton Flex
40 °C
90 °C - Cold
Cotton1)
40 °C
60 °C - 40 °C
Synthetics
40 °C
60 °C - Cold
Delicate
30 °C
40 °C - Cold
1600 rpm
(1600400 rpm)
10 kg
White cotton and coloured cotton. Normal, heavy
and light soil.
1600 rpm
(1600400 rpm)
10 kg
White cotton and fast-coloured cotton. Normal
soil. The energy consumption decreases and the time
of the washing programme is extended, ensuring good
washing results.
1200 rpm
(1200 400 rpm)
4 kg
Synthetic items or mixed fabric items. Normal
soil.
1200 rpm
(1200400 rpm)
4 kg
Delicate fabrics such as acrylics, viscose and
mixed fabrics requiring gentler washing. Normal
soil.
13
Programme
Reference
Default temperaspin speed Maximum
ture
Spin speed
load
Temperature
range
range
Steam programmes
Programme description
(Type of load and soil level)
with FreshScent System
Steam programmes can be used for reducing wrinkles and odours2) of garments that just need to be
refreshed, avoiding washing. The fabric fibres are relaxed and afterwards ironing becomes effortless.
When the programme is completed, quickly remove the laundry from the drum3). Steam programme
does not perform any hygienic cycle. Do not set this programme with the following type of items:
• Items that are not suitable for tumble drying.
• All items with plastic, metal, wooden parts or alike.
ELECTROLUX fragrance. If you use this special gentle fragrance, your laundry will scent as just
washed: pour a single dose bottle in the compartment
and simply start a steam programme. Reduce the fragrance dosage when treating smaller load. By means of the Time Manager button, you can
reduce the programme duration when treating items labeled to be washed at low temperature.
DO NOT:
• Tumble dry the garments treated with fragrance. Its benefit would evaporate.
• Use the fragrance with different purposes than those here described.
• Use the fragrance on new garments. New garments may contain residual finishing compounds
which are not compatible with it.
The fragrance dose bottles are available on ELECTROLUX web shop or by authorised
dealer.
1 kg
Delicate Steam
-
Wool and cashmere. Short programme to refresh
maximum 1 kg of machine and hand washable woolen
and cashmere garments without washing. When treating smaller loads, the programme duration can be further reduced by means of the Time Manager option.
WARNING! Do not use this programme
with woolen garments labelled as dryclean only.
1 kg
Steam Refresh
-
Cottons, Synthetics, Delicates. Short and gentle
steam programme to refresh even your very delicate
garments, including very delicate garments with sequins, lace etc. When treating smaller loads, the programme duration can be further reduced by means of
the Time Manager option.
WARNING! Do not use this programme
with wool and garments labelled as dryclean only.
Special programmes
14
Programme
Reference
Default temperaspin speed Maximum
ture
Spin speed
load
Temperature
range
range
Programme description
(Type of load and soil level)
10 kg
Spin/Drain
1600 rpm
(1600 400 rpm)
All fabrics, except woollens and delicate fabrics. To spin the laundry and to drain the water in the
drum.
1600 rpm
(1600400 rpm)
10 kg
Rinse
All fabrics, except woollens and very delicate
fabrics. Programme for rinsing and spinning the laundry. The default spin speed is the one used for cotton
programmes. Reduce the spin speed accordingly to
the type of laundry. If necessary, set the Extra Rinse
option to add rinses. With a low spin speed, the appliance performs delicate rinses and a short spin.
Additional washing programmes
Duvet
40 °C
60 °C - Cold
Rapid 14min
30 °C
800 rpm
(800 - 400
rpm)
3 kg
Single synthetic blanket, padded clothes, duvets, down jackets and similar items.
800 rpm
(800- 400
rpm)
1.5 kg
Synthetic and mixed fabric items. Light soil and
items to freshen up.
15
Programme
Reference
Default temperaspin speed Maximum
ture
Spin speed
load
Temperature
range
range
Outdoor
30 °C
40 °C - Cold
1200 rpm
(1200400 rpm)
Programme description
(Type of load and soil level)
2.5
kg4)
1 kg5)
Do not use fabric softener and make sure
that there is no softener residue in the
detergent dispenser.
Synthetic sport items. This programme is designed
to gently wash modern outdoor sportswear and is also
suitable for gym, cycling or jogging clothes or similar.
The recommended laundry load is 2.5 kg.
Waterproof, waterproof-breathable and water
repellent fabrics. This programme can also be used
as a water repellency restoring cycle, specifically tailored for treating clothes with a hydrophobic coating.
To perform the water repellency restoring cycle, proceed as follows:
• Pour the washing detergent in the compartment
•
.
Pour a special water repellency restorer for fabric
•
into the softener compartment of the drawer
Reduce the laundry load to 1 kg.
.
To further improve the water repellency
restoring action, dry the laundry in a tumble dryer by setting the Outdoor drying
programme (if available and if the garment care label permits tumble drying).
Denim
30 °C
40 °C - Cold
UltraWash
30 °C
60 °C - 30 °C
16
800 rpm
(1200 400 rpm)
4 kg
Special programme for Denim clothing with delicate washing phase to minimize colour fading
and marks. For better care a reduced load size is
recommended.
1600 rpm
(1600 400 rpm)
5 kg
Cotton items. Intensive programme for ensuring
good washing performances in a short time.
Programme
Reference
Default temperaspin speed Maximum
ture
Spin speed
load
Temperature
range
range
Wool/Silk
40 °C
40 °C - Cold
1200 rpm
(1200 400 rpm)
Programme description
(Type of load and soil level)
2 kg
Machine washable wool, hand washable wool
and other fabrics with «hand washing» care symbol6).
1) Standard programme for the "Egyptian" Energy Label consumption values. According to regulation 4100/2006 , the most efficient for washing soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the
selected programme.
2) Steam programme doesn't remove particularly intense odour.
3) After the steam treatment the laundry can be humid. Hang items out for a few minutes.
4) Washing programme.
5) Washing programme and waterproofing phase.
6) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't
rotate or doesn't rotate properly, but this is normal for this programme.
■
■
■
■
■
■
■
■
■
■
■
■
■
Synthetics
■
■
■
■
■
■
■
■
Delicate
■
■
■
■
■
■
■
■
Time Manager
■
■
Delay Start
■
Silent
Plus Steam
Soft Plus
Extra Rinse
Stain 2)
Cotton Flex
Cotton
Programme
Spin
Prewash1)
No Spin
Programme options compatibility
■
■
■
■
■
■
■
■
■
Delicate Steam
■
■
Steam Refresh
■
■
Spin/Drain
■
■3)
Rinse
■
■
Duvet
■
■
Rapid 14min
■
■
■
Outdoor
■
■
■
■
■
■
■
■
■
■
■
■
17
Denim
■
■
■
■
■
UltraWash
■
■
■
■
■
Wool/Silk
■
■
■
■
Time Manager
Delay Start
Silent
Plus Steam
Soft Plus
Extra Rinse
Stain 2)
Prewash1)
No Spin
Spin
Programme
■
■
■
1) Prewash and Stain cannot be selected together.
2) This option is not available with temperature lower than 40 °C.
3) If you set the No Spin option, the appliance performs draining only.
WOOLMARK APPAREL CARE - GREEN
The wool wash cycle of this machine has been approved by The Woolmark Company for the washing of wool garments labelled as «hand wash» provided that the garments are washed according to
the instructions issued by the manufacturer of this
washing machine. Follow the garment care label
for drying and other laundry instructions. M1361
The Woolmark symbol is a Certification mark in
many countries.
SETTINGS
ACOUSTIC SIGNALS
This appliance has different acoustic signals, that
operate when:
• You activate the appliance (special short tune).
• You deactivate the appliance (special short
tune).
• You touch the buttons (click sound).
• You make an invalid selection (3 short sounds).
• The programme is completed (sequence of
sounds for about 2 minutes).
• The appliance has a malfunction (sequence of
short sounds for about 5 minutes).
To deactivate/activate the acoustic signals when
the programme is completed, touch the Prewash
and the Stain buttons simultaneously for about 2
seconds. The display shows On/Off
18
If you deactivate the acoustic signals,
they continue to operate when the
appliance has a malfunction.
CHILD LOCK
With this option you can prevent children from
playing with the control panel.
To activate/deactivate this option, hold down the
Silent button until
comes on/goes off on the
display.
The appliance will default to this option after you
switch it off.
The Child Lock function may not be available for a
few seconds after switching the appliance on.
BEFORE FIRST USE
1. Make sure that the electrical power is available
and the water tap is open.
2. Pour 2 litres of water into the detergent
.
compartment marked by
This action activates the drain system.
3. Pour a small quantity of detergent into the
compartment marked by
4. Set and start a programme for cotton at the
highest temperature without any laundry in the
drum.
This removes all possible dirt from the drum and the
tub.
.
DAILY USE
WARNING! Refer to Safety chapters.
FILLING THE DETERGENT AND ADDITIVES
ACTIVATING THE APPLIANCE
1. Connect the mains plug to the mains socket.
2. Open the water tap.
3. Press the On/Off button for a few seconds to
activate the appliance.
A short tune sounds.
LOADING THE LAUNDRY
1. Open the appliance door.
2. Empty the pockets and unfold the items before
you put them in the appliance.
3. Put the laundry in the drum, one item at a time.
Do not put too much laundry in the drum.
4. Close the door firmly.
- Compartment for prewash phase, soak
programme or stain remover.
- Compartment for washing phase.
- Compartment for fabric softener and other
liquid treatments(fabric conditioner, starch).
- Maximum level for quantity of liquid additives.
- Flap for powder or liquid detergent.
CAUTION! Make sure that no laundry
gets caught between the seal and the
door to avoid risk of water leakage and
damage to the laundry.
Washing heavily oiled, greasy stains
could cause damage to rubber parts
of the washing machine.
Always follow the instructions that you
find on the packaging of the detergent
products, but we recommend that you
do not exceed the maximum indicated
level (
). This quantity will
however guarantee the best washing
results.
After a washing cycle, if necessary,
remove any detergent residue from the
detergent dispenser.
19
CHECK THE POSITION OF THE DETERGENT
FLAP
1. Pull out the detergent dispenser until it stops.
SETTING A PROGRAMME
1. Turn the programme dial to select the desired
washing programme.
The indicator of the Start/Pause
button flashes.
The display shows an indicative programme
duration and the maximum load.
2. To change the temperature and/or the spin
speed, touch the related buttons.
3. If desired, set one or more options by touching
the related buttons. The related indicators
illuminate on the display and the given
information changes accordingly.
If a selection is not possible an
acoustic signal sounds and the display
2. Press the lever down to remove the dispenser.
3. To use powder detergent, turn the flap up.
4. To use liquid detergent, turn the flap down.
shows
.
STARTING A PROGRAMME
Touch the Start/Pause
button to start the
programme. It is not possible to start the
programme when the indicator of the button is off
and doesn't flash (e.g. programme dial on a wrong
position).
The related indicator stops flashing and stays on.
The programme starts, the door is locked. The
display shows the indicator
.
The drain pump can operate shortly
before the appliance fills water.
With the flap in the position DOWN:
• Do not use gelatinous or thick liquid
detergents.
• Do not exceed to liquid detergent dose
indicated on the flap.
• Do not set the prewash phase.
• Do not set the delay start function.
5. Measure out the detergent and the fabric
conditioner.
6. Carefully close the detergent dispenser.
STARTING A PROGRAMME WITH THE DELAY
START
1. Touch the Delay Start
button repeatedly until
the display shows the desired delay time. On the
display the indicator shows
2. Touch the Start/Pause
button. The appliance
door locks and starts the countdown of the delay
start. The display shows the indicator
.
When the countdown is completed, the programme
starts automatically.
Cancelling the delay start after the
countdown has started
To cancel the delay start:
button repeatedly
1. Touch the Delay Start
until the display shows the desired delay time.
On the display the indicator shows
Touch the Start/Pause
button. The appliance
lock the door and starts the countdown of the delay
Make sure that the flap does not cause a blockage
when you close the drawer.
20
start. The display shows the indicator
.
When the countdown is completed, the programme
starts automatically.
despite the overload. In this case, it will be not
possible to guarantee the best washing results.
2. Touch the Start/Pause
button to pause the
appliance. The related indicator flashes.
About 20 minutes after the programme
start, the programme duration could
be adjusted again depending on the
capacity of water absorption of the
fabrics.
3. Touch the Delay Start
until the display shows
goes off.
button repeatedly
and the indicator
4. Touch the Start/Pause
button again to
start the programme immediately.
The AutoAdjust detection is carried
out with complete washing
programmes only and if the
programme duration has not been
reduced by means of the Time
Manager button.
Changing the delay start after the countdown
has started
To change the delay start:
1. Touch the Start/Pause
button to pause the
appliance. The related indicator flashes.
2. Touch the Delay Start
button repeatedly
until the display shows the desired delay time.
3. Touch the Start/Pause
button again to
start the new countdown.
THE AUTOADJUST SYSTEM LOAD
DETECTION
The programme duration in the display
is referred to a medium/high load.
After touching the Start/Pause
button, the
maximum declared load indicator goes off, the
AutoAdjust System starts the laundry load
detection:
1. The appliance detects the load in the first 30
seconds. In the programmes where Time
Manager is available, during this phase the
INTERRUPTING A PROGRAMME AND
CHANGING THE OPTIONS
When the programme is running, you can change
only some options:
1. Touch the Start/Pause
button.
The related indicator flashes.
2. Change the options. The given information in
the display changes accordingly.
3. Touch the button Start/Pause
The washing programme continues.
CANCELLING A RUNNING PROGRAMME
1. Press the button On/Off to cancel the
programme and to deactivate the appliance.
2. Press the button On/Off again to activate the
appliance.
If the AutoAdjust System has
completed and the water filling has
already started, the new programme
starts without repeating the
AutoAdjust System. The water and
the detergent are not drained out in
order to avoid waste. The display
shows the maximum duration of the
programme, updating it about 20
minutes after the starting of the new
programme.
Time Manager bars
placed below the
time digits play a simple animation. The drum
rotates shortly.
2. The programme duration could be adjusted
accordingly and could increase or decrease.
After further 30 seconds, the water filling starts.
At the end of the load detection, in case of drum
overload, the indicator
is flashing in the
display:
In this case, for 30 seconds, it is possible to pause
the appliance and remove the exceeding garments.
Once removed the exceeding garments, touch the
button to start the programme
Start/Pause
again. The AutoAdjust phase can be repeated up to
three times (see point 1).
Important! If the laundry amount will not be
reduced, the washing programme starts anyway,
again.
There is also an alternative way of cancelling:
1. Rotate the selector knob to the "Reset" position
.
2. Wait for 1 second. The display shows
.
Now, you can set a new washing programme.
21
OPENING THE DOOR - ADDING GARMENTS
If the temperature and level of the
water in the drum are too high and/or
the drum is still rotating you should not
open the door.
While a programme or the delay start operates, the
appliance door is locked. The display shows the
indicator
.
1. Touch the Start/Pause
button.
In the display the related door lock indicator goes
off.
2. Open the appliance door. If necessary, add or
remove the items. Close the door and touch
button.
the Start/Pause
The programme or the delay start continues.
END OF THE PROGRAMME
When the programme has finished, the appliance
stops automatically. The acoustic signals operate (if
they are active). The display shows
The indicator of the Start/Pause
off.
button goes
The door unlocks and the indicator
goes off.
1. Press button On/Off to deactivate the
appliance.
After five minutes from the end of the programme,
the energy saving function automatically
deactivates the appliance.
2.
3.
4.
5.
When you activate the appliance
again, the display shows the end of
the previous programme. Turn the
programme dial to set a new cycle.
Remove the laundry from the appliance.
Make sure that the drum is empty.
Keep the door and the detergent dispenser
slightly ajar to prevent mildew and odours.
Close the water tap.
DRAINING WATER OUT AFTER END OF
CYCLE
If you have chosen a programme or an option that
does not empty out the water of the last rinse, the
programme is completed, but:
•
The time area shows
shows the door locked
22
and the display
.
button
The indicator of the Start/Pause
starts flashing.
• The drum still turns at regular intervals to
prevent creases in the laundry.
• The door stays locked.
• You must drain the water to open the door:
1. If necessary, touch the Spin button to decrease
the spin speed proposed by the appliance.
•
2. Press the Start/Pause
button: the
appliance drains the water and spins.
The option indicator Rinse Hold
disappears.
or
If you have set Silent
and the spin
speed is not changed, when you press
the Start/Pause
button, the
appliance only drains the water.
3. When the programme is completed and the
door locked indicator
goes off, you can
open the door.
4. Press the On/Off button for a few seconds to
deactivate the appliance.
STAND-BY FUNCTION
The Stand-by function automatically deactivates the
appliance to reduce the energy consumption when:
• You do not use the appliance for 5 minutes
when no programme is running.
Press the button On/Off to activate the
appliance again.
• 5 minutes after the end of the washing
programme.
Press the On/Off button to activate the
appliance again.
The display shows the end of the last
programme.
Turn the programme dial to set a new cycle.
If the dial is rotated to the "Reset" position
, the
appliance automatically turns off in 30 seconds.
If you set a programme or an option
that ends with water in the drum, the
Stand-by function doesn't
deactivate the appliance to remind
you to drain the water.
HINTS AND TIPS
WARNING! Refer to Safety chapters.
THE LAUNDRY LOAD
• Divide the laundry into: white, coloured,
synthetics, delicates and wool.
• Follow the washing instructions on the laundry
care labels.
• Do not wash white and coloured items together.
• Some coloured items can discolour with the first
wash. We recommend that you wash them
separately for the first couple of times.
• Button up pillowcases, close zippers, hooks and
poppers. Tie up belts.
• Turn multilayered fabrics, wool and items with
printed illustrations inside out.
• Pre-treat tough stains.
• Wash heavy soil stains with a special detergent.
• Be careful with curtains. Remove the hooks and
put the curtains in a washing bag or pillowcase.
• Do not wash laundry without hems or with cuts.
• Use a washing bag to wash small and/or
delicate items (e.g. underwired bras, belts,
tights, etc. ).
• A very small load can cause balance problems
with the spin phase leading to excessive
vibration. If this occurs:
a. interrupt the programme and open the
door (refer to "Daily Use" chapter);
b. manually redistribute the load so that the
items are spaced evenly around the tub;
c. press the Start/Pause button. The spin
phase continues.
• Avoid washing garments full of long animal hair
or poor quality garments releasing lots of fluff
that could block the drain circuit and therefore
requiring the Service assistance.
• Empty pockets and unfold the items.
STUBBORN STAINS
For some stains, water and detergent is not
sufficient.
We recommend that you pre-treat these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the type
of stain and fabric.
DETERGENTS AND OTHER TREATMENTS
• Only use detergents and other treatments
specially made for washing machines:
– powder detergents for all types of fabric,
excluding delicate. Prefer powder
detergents containing bleach for whites and
laundry sanitization
– liquid detergents, preferably for low
temperature wash programmes (60 °C max)
for all types of fabric, or special ones for
woollens only.
• Do not mix different types of detergents.
• To help the environment, do not use more than
the recommended quantity of detergent.
• Follow the instructions that you find on
packaging of the detergents or other treatments
without exceeding the indicated maximum level
•
(
).
Use the recommended detergents for the type
and colour of the fabric, the programme
temperature and the level of soil.
ECOLOGICAL HINTS
• Set a programme without the prewash phase to
wash laundry with normal soil.
• Always start a washing programme with the
maximum load of laundry allowed.
• If you pre-treat the stains or use a stain remover,
set a programme with a low temperature.
• To use the correct quantity of detergent, check
the water hardness of your domestic system.
Refer to "Water hardness".
WATER HARDNESS
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where the
water hardness is soft it is not necessary to use a
water softener.
To find out the water hardness in your area, contact
your local water authority.
Use the correct quantity of water softener. Follow
the instructions that you find on the packaging of
the product.
23
CARE AND CLEANING
WARNING! Refer to Safety chapters.
EXTERNAL CLEANING
Clean the appliance with mild soap and warm water
only. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
CAUTION! Do not clean the metal
surfaces with chlorine-based
detergent.
DESCALING
If the water hardness in your area is
high or moderate, we recommend that
you use a water descaling product for
washing machines.
Regularly examine the drum to check for limescale.
Regular detergents already contain water softening
agents, but we recommend to run a cycle with an
empty drum and a descaling product occasionally.
Always follow the instructions that you
find on the packaging of the product.
MAINTENANCE WASH
The repeated and prolonged use of low
temperature programmes can cause detergent
deposits, fluff residues, bacterial growth inside the
drum and the tub. This could generate bad odours
and mildew. To eliminate these deposits and clean
the inner part of the appliance, run a maintenance
wash regularly (at least once a month).
Refer to Cleaning the drum chapter.
DOOR SEAL WITH DOUBLE LIP TRAP
This appliance is designed with a self cleaning
draining system, allowing light fluff fibers that fall
off the clothes to be drained out with the water, in
such a way that there is no need by the customer to
access this area for regular maintenance and
cleaning.
24
Regularly examine the seal and remove all objects
from the inner part. Coins, buttons, other small
items forgotten in the pockets of your clothes are
deposited during the washing cycle in the special
double lip trap in the porthole seal, where they can
be conveniently recovered at the end of the cycle.
CLEANING THE DRUM
Regularly examine the drum to prevent unwanted
deposits.
Rust deposits in the drum may occur due to rusting
foreign body in the washing or tap water containing
iron
Clean the drum with special products for stainless
steel.
Always follow the instructions that you
find on the packaging of the product.
Do not clean the drum with acidic
descaling products, scouring products
containing chlorine or iron or steel
wool.
For a thorough clean:
1. Remove all laundry from the drum.
2. Run a Cotton Flex programme with the highest
temperature.
3. Add a small quantity of powder detergent into
the empty drum, in order to rinse out any left
residues.
Occasionally, at the end of a cycle the
display may show the icon
: this is a
recommendation to perform the “drum
cleaning”. Once the drum cleaning has
been performed, the icon disappears.
CLEANING THE DETERGENT DISPENSER
To prevent possible deposits of dried detergent or
clotted fabric softener and/or formation of mould in
the detergent dispenser drawer, once in a while
carry out the following cleaning procedure:
1. Open the drawer. Press the catch downwards
as indicated in the picture and pull it out.
without any clothes in the drum.
1
2
2. Remove the top part of the additive
compartment to aid cleaning and flush it out
under running warm water, to remove any
traces of accumulated detergent. After
cleaning, put the top part back into position.
CLEANING THE DRAIN PUMP
WARNING! Disconnect the mains
plug from the mains socket.
Regularly check the drain pump filter
and make sure that it is clean.
Clean the drain pump if:
• The appliance does not drain the water.
• The drum does not turn.
• The appliance makes an unusual noise because
of the blockage of the drain pump.
•
3. Make sure that all detergent residue is removed
from the upper and lower part of the recess.
Use a small brush to clean the recess.
The display shows the alarm code
.
WARNING!
• Do not remove the filter while the
appliance operates.
• Do not clean the pump if the water
in the appliance is hot. Wait until
the water cools down
Proceed as follows to clean the pump:
1. Open the pump cover.
4. Insert the detergent drawer into the guide rails
and close it. Run the rinsing programme
2
1
2. Place a suitable bowl below the drain pump
access to collect the water that flows out.
3. Open the chute downwards. Always keep a rag
nearby to dry up any water spillages when
removing the filter.
25
4. Turn the filter 180 degrees in anti-clockwise
direction to open it, without removing. Let the
water flow out.
10. Clean the filter under the water tap.
11. Put the filter back into the special guides by
turning it clockwise. Make sure that you tighten
the filter correctly to prevent leakages.
2
5. When the bowl is full of water, turn the filter
back and empty the container.
6. Repeat the steps 4 and 5 until the water stops
to flow out.
7. Turn the filter anti-clockwise to remove it.
1
12. Close the pump cover.
1
2
8. If it is necessary, remove fluff and objects from
the filter recess.
9. Make sure that the impeller of the pump can
rotate. If it does not rotate, contact the
Authorised Service Centre.
26
2
1
When you drain the water with the emergency drain
procedure, you must activate the drain system
again:
a. Put 2 litres of water in the main wash
compartment of the detergent dispenser.
b. Start the programme to drain the water.
CLEANING THE INLET HOSE AND THE VALVE FILTER
1
2
3
45°
20°
EMERGENCY DRAIN
If the appliance cannot drain the water, carry out
the same procedure, described in 'Cleaning the
drain pump' paragraph. If necessary, clean the
pump.
When you drain the water with the emergency drain
procedure, you must activate the drain system
again:
1. Put 2 litres of water in the main wash
compartment of the detergent dispenser.
2. Start the programme to drain the water.
FROST PRECAUTIONS
If the appliance is installed in an area where the
temperature can reach values around 0° C or drop
below, remove the remaining water from the inlet
hose and the drain pump.
1. Disconnect the mains plug from the mains
socket.
2. Close the water tap.
3. Put the two ends of the inlet hose in a
container and let the water flow out of the
hose.
4. Empty the drain pump. Refer to the emergency
drain procedure.
5. When the drain pump is empty, install the inlet
hose again.
WARNING! Make sure that the
temperature is higher than 0 °C before
you use the appliance again.
The manufacturer is not responsible
for damages caused by low
temperatures.
27
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
INTRODUCTION
The appliance does not start or it stops during operation.
First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised
Service Centre.
WARNING! Deactivate the appliance before carrying out any check.
In case of major problems, the acoustic signals operate, the display shows an alarm code and
the Start/Pause
•
•
•
button may flash continuously:
- The mains supply is unstable. Wait until the mains supply is stable.
- No communication between electronic elements of the appliance. Switch it off and switch on
again. The programme was not finished properly or the appliance stopped too early. If the alarm code
appears again, contact the Authorised Service Centre.
- The appliance does not fill with water properly. After the proper check, start the appliance
again by pressing Start/Pause
button the appliance tries to resume the cycle . If the error persists
the alarm code will appear again.
•
- The appliance does not drain the water.
•
- The appliance door is open or not closed correctly. Please check the door!
If the appliance is overloaded, remove some items from the drum and/or hold the door shut
while touching the Start/Pause
picture below).
28
button until the indicator
stops flashing (see the
POSSIBLE FAILURES
Problem
The programme does not
start.
Possible solution
•
•
•
Make sure that the mains plug is connected to the mains socket.
Make sure that the appliance door is closed.
Make sure that there is no damaged fuse in the fuse box.
•
•
Make sure that the Start/Pause
has been touched.
If the delay start is set, cancel the setting or wait for the end of
countdown.
Deactivate the Child Lock function if it is on.
Check the position of the knob on the selected programme.
•
•
•
•
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low. For
this information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the inlet hose has no kinks, damages or bends.
Make sure that the connection of the water inlet hose is correct.
Make sure that the filter of the inlet hose and the filter of the valve
are not clogged. Refer to 'Care and cleaning'.
The appliance does not fill
with water properly.
•
•
•
•
The appliance fills with water and drains immediately
•
Make sure that the drain hose is in the correct position. The hose
may be positioned too low. Refer to "Installation instruction".
•
•
•
Make sure that the sink spigot is not clogged.
Make sure that the drain hose has no kinks or bends.
Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to "Care and cleaning".
Make sure that the connection of the drain hose is correct.
Set the drain programme if you set a programme without drain
phase.
Set the drain programme if you set an option which ends with water
in the tub.
The appliance does not
drain the water.
•
•
•
The spin phase does not
operate or the washing cycle lasts longer than usual.
•
•
•
•
There is water on the floor.
•
•
•
You cannot open the appliance door.
•
•
•
•
Set the spin programme.
Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to "Care and cleaning".
Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
Make sure that the couplings of the water hoses are tight and there
is not water leakages.
Make sure that the water inlet hose and the drain hose have no
damages.
Make sure you use the correct detergent and the correct quantity of
it.
Make sure that a washing programme that ends with water in tub,
has been selected.
Make sure that the washing programme is finished.
Set the drain or the spin programme if there is water in the drum.
Make sure that the appliance receives electrical power.
This problem may be caused by a failure of the appliance. Contact
the Authorised Service Centre.
If you need to open the door, please read carefully "Emergency
door opening".
29
Problem
Possible solution
•
The appliance makes an
unusual noise and vibrates.
•
•
The programme duration
increases or decreases
during programme execution.
Make sure the levelling of the appliance is correct. Refer to "Installation instruction".
Make sure that the packaging and/or the transit bolts are removed.
Refer to "Installation instruction".
Add more laundry in the drum. The load may be too small.
•
The AutoAdjust System is able to adjust the programme duration
according to the type and the laundry load size. Refer to "The AutoAdjust System load detection" in "Daily Use" chapter.
•
•
•
•
Increase the detergent quantity or use a different detergent.
Use special products to remove the stubborn stains before you
wash the laundry.
Make sure that you set the correct temperature.
Decrease the laundry load.
Too much foam in the
drum during the washing
cycle.
•
Reduce the quantity of detergent.
After the washing cycle,
there are some detergent
residues in the dispenser
drawer.
•
Make sure that the flap is in the correct position (UP for powder
detergent - DOWN for liquid detergent).
Make sure you have used the detergent dispenser according the
indications given in this user manual.
The washing results are
not satisfactory.
•
After the check, activate the appliance. The programme continues from the point of interruption.
If the problem occurs again, contact the Authorised Service Centre.
If the display shows other alarm codes, deactivate and activate the appliance. If the problem continues,
contact the Authorised Service Centre.
EMERGENCY DOOR OPENING
In case of power failure or functioning failure the
appliance door remains locked. The washing
programme continues when the power is restored.
If the door remains locked in case of failure, it is
possible to open it using the emergency unlock
function.
Before opening the door:
CAUTION! Risk of burns! Make
sure that the water temperature is
not too high and the laundry is
not hot. If necessary, wait until
they cool down.
CAUTION! Risk of injury! Make
sure that the drum is not rotating.
If necessary, wait until the drum
stops rotating.
30
Make sure that the water level
inside the drum is not too high. If
necessary, proceed with an
emergency drain (refer to
«Emergency drain» in «Care and
cleaning» chapter).
To open the door, proceed as follows:
1. Press the On/Off button to switch the
appliance off.
2. Disconnect the mains plug from the mains
socket.
3. Open the filter flap.
4. Pull the emergency unlock trigger downward
once. Pull it downward once again, keep it
tensed and, in the meanwhile, open the
appliance door.
5. Take out the laundry and then close the
appliance door.
6. Close the filter flap.
CONSUMPTION VALUES
Stated values are obtained in laboratory conditions with relevant standards. Different causes can change the data: the quantity and type of laundry and ambient temperature. Water pressure, the supply voltage and the temperature of inlet water may also affect the
washing programme duration.
Technical specifications may be changed without prior notice to improve the quality of
product.
At the start of the programme, the display shows the programme duration for the maximum load capacity.
During the washing phase the programme duration is automatically calculated and can be
greatly reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton
60°C, maximum load capacity 10 kg, the programme duration exceeds 2 hours; actual
load 1 kg, the programme duration will be less than 1 hour).
When the appliance is calculating the real programme duration a dot flashes in the display.
Programmes
Load (kg)
Energy consumption
(kWh)
Approximate
Water con- programme dusumption (litre) ration (minutes)
Cotton Flex
60°C
10
1.85
90
240
Cotton
60°C1)
10
0.75
60
260
Cotton Flex
40°C
10
1.30
90
220
Synthetics
40°C
4
0.72
55
160
31
Programmes
Load (kg)
Approximate
Water con- programme dusumption (litre) ration (minutes)
Energy consumption
(kWh)
Delicate
40°C
4
0.60
60
120
Wool/Silk
30°C
2
0.35
59
60
1) This programme at 60 °C with a load of 10 kg is the reference programme for energy label data, in compliance with UAE. S 5010 2:2013.
Off Mode (W)
Left On Mode (W)
0.30
0.30
The data in this chart are measured according to IEC 62301.
TECHNICAL DATA
Dimension
Width/ Height/ Depth/ Total depth
600 mm/ 850 mm/ 631 mm/ 660 mm
Electrical connection
Voltage
Overall power
Fuse
Frequency
220 - 240 V
2200 W
10 A
50 Hz
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where
the low voltage equipment has no protection against
moisture
IPX4
Water supply pressure
0.5 bar (0.05 MPa)
8 bar (0.8 MPa)
Minimum
Maximum
Cold water
Water supply 1)
Maximum Load
Cotton
Energy Efficiency Class
Spin Speed
10 kg
A+++
Maximum spin speed
1551 rpm
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
ACCESSORIES
AVAILABLE IN WWW.ELECTROLUX.COM/SHOP OR FROM AUTHORISED DEALER
Only appropriate accessories approved by ELECTROLUX ensure the safety standards of the
appliance. If unapproved parts are used, any claims will be invalidated.
32
FIXING PLATE KIT (4055171146)
Available from your authorised dealer.
If you install the appliance on a plinth, secure the
appliance in the fixing plates.
Read carefully the instructions supplied with the
accessory.
STACKING KIT
The stacking kit can be used only with the
appliances specified in the leaflet provided with the
accessory.
Read carefully the instructions supplied with the
appliance and with the accessory.
WARNING! Do not put the tumble
dryer under the washing machine.
PEDESTAL WITH THE DRAWER
The tumble dryer can be stacked on the top of the
washing machine only by using the correct
stacking kit manufactured and approved by
ELECTROLUX.
Verify the compatible stacking kit by
checking the depth of your appliances.
To raise your appliance and make loading and
unloading laundry easier.
The drawer can be used for laundry storage e.g.:
towels, cleaning products and more.
Read carefully the instructions supplied with the
accessory.
33
QUICK GUIDE
DAILY USE
1
2
3
5
4
Connect the mains plug to the mains socket.
Open the water tap.
Load the laundry.
Pour the detergent and other treatment in the
proper compartment of the detergent dispenser.
1. Push the On/Off button to turn the appliance
on.
2. Turn the programme dial to set the desired
programme.
3. Set the desired options by means of the
corresponding touch buttons.
4. To start the programme, touch the Start/
Pause
button.
5. The appliance starts.
At the end of the programme, remove the laundry.
Push the On/Off button to turn the appliance off.
CLEANING THE DRAIN PUMP FILTER
1
2
3
180˚
1
2
Clean the filter regularly and, especially, if the alarm
code
34
appears on the display.
ENVIRONMENTAL CONCERNS
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
Recycle materials with the symbol
. Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
35
*
157026020-A-482018
WWW.ZANUSSI.COM/SHOP