IMPORTANT SAFETY INSTRUCTIONS
• This product may contain
Fluorinated Greenhouse Gases
covered by the Kyoto Protocol; the
refrigerant gas is inside a
hermetically sealed system.
Refrigerant gas: R134a has a Global
Warming Potential of (GWP) 1300.
• C-Pentane is used as blowing agent
in the insulation foam and it is a
flammable gas. Pay special attention
during disposal operations.
• This appliance is intended to be
used in household and similar
applications such as
- staff kitchen areas in shops,
offices and other working
environments;
- farm houses and by clients in
hotels, motels and other
residential type environments;
- bed and breakfast type
environments;
- catering and similar non-retail
applications
• Do not store explosive substances
such as aerosol cans with a
flammable propellant in this
appliance.
• This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance in a
safe way and understand the
hazards involved.
• Cleaning and user maintenance
shall not be made by children
without supervision.
• WARNING: to avoid a hazard
due to instability, positioning or
fixing of the appliance must be
done in accordance with the
manufacturer instructions.
• WARNING: keep the appliance
ventilation openings clear of
obstruction.
• WARNING: do not damage the
appliance refrigerant circuit pipes.
• WARNING: Do not use
mechanical, electric or chemical
means other than those
recommended by the
Manufacturer to speed up the
defrost process.
• WARNING: Do not use or place
electrical devices inside the
appliance compartments if they
are not of the type expressly
authorised by the Manufacturer.
• WARNING: ice-makers and/or
water dispensers not directly
connected to the water supply
must be filled with potable water
only.
Information: This appliance does
not contain CFCs. The refrigerant
circuit contains R134a (HFC) or
R600a (HC) (see the rating plate
inside the appliance).
• Appliances with Isobutane (R600a):
isobutane is a natural gas without
environmental impact, but is
flammable. Therefore, make sure
the refrigerant circuit pipes are not
damaged. Keep special attention in
case of damaged pipes emptying
the refrigerant circuit.
4
• To avoid the risk of children
becoming trapped and suffocating,
do not allow them to play or hide
inside the appliance.
• It must be possible to disconnect
the appliance from the power
supply by unplugging it if plug is
accessible, or by means of an
accessible multi-pole switch
installed upstream of the socket in
conformity with national safety
standards.
• Plug the appliance into a grounding
socket: the appliance must be
correctly connected to an
approved earthing system.
• Do not use single/multi adapters or
extension cords.
• During installation, make sure the
appliance does not damage the
power cable.
• Do not pull the aplliance power
cable
• The appliance must be handled and
installed by two or more persons.
• Installation and maintenance
including replacement of the supply
cord must be carried out by the
manufacturer or a qualified
technician, in compliance with the
manufacturer’s instructions and the
local safety regulations in force. In
order to avoid a hazard do not
repair or replace any part of the
appliance including the supply cord,
unless specifically stated in the user
manual.
SAFEGUARDING THE ENVIRONMENT
1. Packing
The packing material is 100% recyclable and bears
the recycling symbol
. For disposal, comply with
the local regulations. Keep the packing materials
(plastic bags, polystyrene parts, etc.) out of the
reach of children, as they are a potential source of
danger.
and shelves so that children cannot easily climb
inside and become trapped.
Scrap the appliance in compliance with local
regulations on waste disposal, taking it to a special
collection centre; do not leave the appliance
unattended even for a few days, since it is a
potential source of danger for children.
For further information on the treatment, recovery
and recycling of this product, contact your
competent local office, the household waste
collection service or the shop where you
purchased the appliance.
2. Scrapping/Disposal
The appliance is manufactured using recyclable
material.
This appliance is marked in compliance with
European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE). By
ensuring the correct disposal of this appliance, you
can help prevent potentially negative consequences
for the environment and the health of persons.
Declaration of conformity
• This appliance has been designed for preserving
food and is manufactured in compliance with
Regulation (CE) No. 1935/2004.
• This appliance has been designed, manufactured
and marketed in compliance with:
- safety objectives of the “Low Voltage”
Directive 2006/95/CE (which replaces
73/23/CEE and subsequent amendments);
- the protection requirements of Directive
“EMC” 2004/108/EC.
The symbol
on the appliance, or on the
accompanying documents, indicates that this
appliance should not be treated as domestic waste
but must be taken to a special collection centre for
the recycling of electrical and electronic equipment.
When scrapping the appliance, make it unusable by
cutting off the power cable and removing the doors
5
BEFORE USING THE APPLIANCE
To ensure best use of your appliance, carefully
read the operating instructions which contain
a description of the product and useful advice.
Keep these instructions for future reference.
2. Wait at least two hours before switching the
appliance on, to ensure that the refrigerant
circuit is fully efficient.
3. Clean the inside of the appliance before using it.
1. After unpacking the appliance, make sure it is
not damaged and that the door closes properly.
Any damage must be reported to the dealer
within 24 hours of delivery of the appliance.
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
INSTALLATION
• Be careful not to damage the floors (e.g.
parquet) when moving the appliance.
• Make sure the appliance is not near a heat
source.
• Install and level the appliance on a floor strong
enough to take its weight and in a place suitable
for its size and use.
• The appliance is arranged for operation in places
where the temperature comes within the
following ranges, according to the climatic class
given on the rating plate. The appliance may not
work properly if it is left for a long time at a
temperature outside the specified range.
Climatic Class
Amb. T. (°C)
SN
From 10 to 32
N
From 16 to 32
ST
From 16 to 38
T
From 16 to 43
• Do not swallow the contents (non-toxic) of the
ice packs (in some models).
• Do not eat ice cubes or ice lollies immediately
after taking them out of the freezer since they
may cause cold burns.
• For products designed to use an air filter inside
an accessible fan cover, the filter shall be always
in position when the refrigerator is in function.
• Before carrying out any maintenance or cleaning
operation, unplug the appliance or disconnect it
from the power supply.
• Use the refrigerator compartment only for
storing fresh food and the freezer compartment
only for storing frozen food, freezing fresh food
and making ice cubes.
• Do not store glass containers with liquids in the
freezer compartment since they may break.
• Avoid storing unwrapped food in direct contact
with internal surfaces of the refrigerator or
freezer compartments.
• “The bulb used inside the appliance is specifically
designed for domestic appliances and is not
suitable for general room lighting within the
home (EC Regulation 244/2009)”.
• Make sure the voltage specified on the rating
plate corresponds to that of your home.
The Manufacturer declines any liability for
injury to persons or animals or damage to
property if the above advice and precautions
are not respected.
SAFE USE
• Do not store or use petrol, flammable liquids or
gas in the vicinity of this or other electrical
appliances. The fumes can cause fires or
explosions.
6
ENERGY-SAVING TIPS
• Appliances could have special compartments
(Fresh Food Compartment, Zero Degree
Box,...). In case not differently specified in the
specific booklet of product, they can be
removed, maintaining equivalent performances.
• Positioning of the shelves in the refrigerator has
no impact on the efficient usage of energy. Food
should be placed on the shelves in such way to
ensure proper air circulation (food should not
touch each other and distance between food and
rear wall should be kept).
• You can increase storage capacity of frozen food
by removing baskets and, if present, Stop Frost
shelve, maintaining an equivalent energy
consumption.
• Damaged gasket must be replaced as soon as
possible.
• High energy class products are fitted with
highefficiency motors that remain operational for
longer, but have a low power consumption. Do
not worry if the engine continues to run for
longer periods.
• Install the appliance in a dry, well ventilated
room far away from any heat source (e.g.
radiator, cooker, etc.) and in a place not exposed
directly to the sun. If required, use an insulating
plate.
• To guarantee adequate ventilation follow
installation instructions.
• Insufficient ventilation on back of the product
increases energy consumption and decreases
cooling efficiency.
• The internal temperatures of the appliance may
be affected by the ambient temperature,
frequency of door opening, as well as location of
the appliance. Temperature setting should take
into consideration these factors.
• Allow warm food and drinks to cool down
before placing in the appliance.
• Do not obstruct the fan (if available) with food
items.
• After placing the food check if the door of
compartments closes properly, especially the
freezer door.
• Reduce to a minimum door opening.
• When thawing frozen food, place them in the
refrigerator. The low temperature of the frozen
products cools the food in the refrigerator.
7
HOW TO USE THE FREEZER
The freezer can be used for storing already frozen
food and for freezing fresh food.
Control unit
Switching on the freezer for the first time
• There is no need to set the freezer temperature on the
thermostat because the appliance is already factory set.
• Plug in the appliance.
• Only place food in the freezer 2 hours after switching on.
Adjusting temperature
From MIN to MAX: make the internal temperature colder.
• Thermostat setting indicator:
MIN - for storing food for short periods;
NORMAL - for storing food for longer periods;
MAX - for storing food for long periods.
Note:
Ambient air temperature, the frequency of door opening
and the position of the appliance can affect the freezer
internal temperature.
Take these factors into consideration when setting the
thermostat knob.
Freezing
Place the amount of fresh food indicated on the
rating plate in the middle compartment. Take care
not to place the food directly in contact with food
already frozen.
It is advisable to maintain the thermostat position used in
normal operation.
Important:
When freezing only small amounts of food, the food can be
placed in any compartment, with the exception of the
bottom drawer.
8
Adjustable feet
Control unit
Tips for freezing and storing fresh food.
• Before freezing, wrap and seal fresh food in: aluminium
foil, cling film, air and water-tight plastic bags, polythene
containers with lids or freezer containers suitable for
freezing fresh food.
• Food must be fresh and of prime quality.
• Fresh vegetables and fruit should preferably be frozen as
soon as they are picked to maintain the full original
nutritional value, consistency, colour and flavour.
Note:
• Always leave hot food to cool before placing in the
freezer.
• Eat fully or partially defrosted foods immediately. Do not
refreeze unless the food is cooked after it has thawed.
Once cooked, the thawed food can be refrozen.
Important:
The table alongside shows the recommended
maximum storage time for frozen fresh foods.
Classification of frozen foods
Put the frozen products into the freezer and classify them.
The storage date should be indicated on the packs, to allow
use within expiry dates.
Advice for storing frozen food
When purchasing frozen food products:
• Ensure that the packaging is not damaged (frozen food in
damaged packaging may have deteriorated). If the
package is swollen or has damp patches, it may not have
been stored under optimal conditions and defrosting may
have already begun.
• When shopping, leave frozen food purchases until last
and transport the products in a thermally insulated cool
bag.
• Once at home, place the frozen foods immediately in the
freezer.
• If food has defrosted even partially, do not re-freeze it.
Consume within 24 hours.
• Avoid, or reduce temperature variations to the minimum.
Respect the best-before date on the package.
• Always observe the storage guidelines on the frozen food
packages.
9
Removing the baskets
• Pull the baskets out fully, then lift them up slightly in
order to remove.
Note:
Drawers may be removed in order to obtain increased
storage space.
Ensure that the load does not exceed the limit (if present)
indicated on the side walls of the appliance.
Making ice cubes
• Fill the ice cube tray 2/3 full and place it in the special
freezer compartment.
• Do not use sharp or pointed instruments to detach the
tray if it is stuck to the bottom of the freezer.
• Bend the ice tray slightly to remove the cubes.
Fig. 1
Note:
The freezer door will not re-open easily immediately after
closing.
Wait a few minutes before opening again in order to allow
for compensation of the vacuum created.
HOW TO DEFROST
AND CLEAN THE FREEZER
Before any cleaning or maintenance operation, always unplug the appliance or disconnect it
from the power supply.
Defrost the freezer once or twice a year, or when the formation of ice on the refrigeration
grilles is excessive.
It is perfectly normal for ice to form on the grilles. The amount of ice which forms and the rate
at which it accumulates will depends on room temperature and humidity, and on the frequency
with which the door is opened.
If possible, defrost the freezer when it is nearly empty.
• Remove the food from the freezer, wrap in newspaper and group together in a cool place or in a
portable cooler.
• Leave the freezer door open to allow the frost to melt.
• Clean the interior of the freezer with a sponge and warm water and/or neutral detergent. Do not use
abrasive substances.
• Rinse the interior and dry thoroughly.
• Put the food back into the freezer.
• Close the freezer door.
• Plug in the appliance once again.
• Switch on the freezer.
10
CLEANING AND MAINTENANCE
Periodically clean the condenser at the rear of the appliance
with a vacuum cleaner or brush.
Prolonged disuse
• Empty the freezer.
• Disconnect the freezer from the mains power supply.
• Defrost and clean.
• Leave the door open to prevent formation of unpleasant
odours and to eliminate any dampness.
TROUBLESHOOTING GUIDE
1. The appliance is not working.
• Is there a power failure?
• Is the main power switch on?
• Do the household electrical system protection
devices work correctly?
• Is the thermostat setting correct?
• Was the appliance switched on correctly?
2. Excessive frost build-up.
• Has the defrost water drain been positioned
correctly?
• Is the door shut properly?
Attention:
• The front edge of the appliance may be hot.
This prevents the formation of condensation
and is not a defect.
• Gurgling and hissing noises due to expansion
in the refrigerant circuit are normal.
AFTER-SALES SERVICE
• your full address,
• your telephone number and area code.
Before contacting the After-Sales Service:
1. See if you can solve the problem yourself with
the help of the “Troubleshooting guide”.
2. Switch the appliance off and then on again to see
if the problem has been solved. If it has not,
switch off the appliance again and repeat the
operation after one hour.
3. If the problem persists after this course of action,
contact After-sales Service.
Specify:
• the nature of the problem,
• the model,
• The Service number (the number after the word
SERVICE on the rating plate inside the appliance),
Note:
The direction of door opening can be changed.
If this operation is performed by After-sales
Service it is not covered by the warranty.
The door cannot be reversed on models with
front handle.
11
INSTALLATION
• Install the appliance away from heat sources. Installation
in a hot environment, direct exposure to the sun or
installation near heat sources (heaters, radiators,
cookers) will increase power consumption and should
therefore be avoided.
• If this is not possible, the following minimum distances
must be respected:
• 30 cm from coal or paraffin stoves;
• 3 cm from electric and/or gas stoves.
• To optimize appliance efficiency, leave a 5 cm gap above
the appliance and make sure that adjacent kitchen units
are sufficiently distanced to allow air circulation.
• Install the appliance in a dry, well-ventilated place, and
ensure it is level, using the front adjustment feet if
necessary.
• Clean the interior.
• Fit the accessories.
Electrical connection
• Electrical connections must be made in accordance
with local regulations.
• Voltage and power consumption are indicated on the
rating plate inside the appliance.
• Regulations require that the appliance be earthed.
The manufacturer declines all liability for injury to
persons or animals and for damage to property
resulting from failure to observe the above
procedures and reminders.
• If the plug and socket are not of the same type, have the
socket replaced by a qualified electrician.
• Do not use extension leads or adapters.
Disconnecting the appliance
It must be possible to disconnect the appliance by
unplugging it or by means of a two-pole switch fitted upline
of the socket.
12
DOOR REVERSIBILITY
The direction of door opening of your freezer can be
changed.
• Make sure that the freezer is not connected to the
power supply and that it is empty.
• Reversing the direction of door opening is a task which
requires two people.
Tools required
• Phillips style screwdriver
• Flat bladed screwdriver
• 8 mm and 10 mm socket or spanner.
Lay the fridge/freezer on its back in order to gain access to
the base, being careful not to tip it back by more than 45º.
Rest it on the soft foam packaging or similar material to
avoid damaging the cooling pipes at the rear of the
appliance.
Remove the two screws on the rear of the fridge/freezer.
Lift the top off the fridge/freezer.
Use the 8 mm socket or spanner to remove the 2 hinge
bolts.
Remove the 2 bolts from the opposite side.
Remove the bracket and plastic surround. Remove and
replace the pin in the bracket.
Refit on the opposite side of the fridge/freezer cabinet.
Remove the blanking plug from the new hinge side and refit
it on the opposite side.
13
Remove the levelling feet by unscrewing.
Remove the bottom bracket using an 8 mm socket or
spanner.
Remove and replace the pin, using a 10 mm socket to
unscrew the nut and a flat bladed screwdriver to remove
the pin. You may need to push the pin through from the
underside to remove fully.
Remove the screw on the base and refit it on the other
side.
Remove the blanking plates from the unused side of the
fridge/freezer and refit them in the holes left by the
brackets.
Replace the door and brackets in reverse order.
When replacing the feet take care to ensure the larger foot
is on the side without the bracket.
Check the door is aligned horizontally and vertically and
that the seal fits properly all around before tightening the
bottom hinge.
Note:
The direction of door opening can be changed. If this
operation is performed by After-sales Service it is not
covered by the warranty.
14
ELECTRICAL CONNECTION
1) For Great Britain only
Warning - this appliance must be earthed
Fuse replacement
If the mains lead of this appliance is fitted with a BS 1363A
13amp fused plug, to change a fuse in this type of plug use an
A.S.T.A. approved fuse to BS 1362 type and proceed as
follows:
1. Remove the fuse cover (A) and fuse (B).
2. Fit replacement 13A fuse into fuse cover.
3. Refit both into plug.
Important:
The fuse cover must be refitted when changing a fuse and if the fuse cover is lost the plug must not be
used until a correct replacement is fitted.
Correct replacement are identified by the colour insert or the colour embossed in words on the base of
the plug.
Replacement fuse covers are available from your local electrical store.
2) For the Republic of Ireland only
The information given in respect of Great Britain will frequently apply, but a third type of plug and socket
is also used, the 2-pin, side earth type.
3) Socket outlet / plug (valid for both countries)
If the fitted plug is not suitable for your socket outlet, please contact Whirlpool Service for further
instruction. Please do not attempt to change plug yourself. This procedure needs to be carried out by a
qualified Whirlpool technician in compliance with the manufactures instructions and current standard
safety regulations.
15
">
