E604.1
ENGLISHInstructions for use
Page 2
1
INSTRUCTION FOR USE
BEFORE USING THE COOKING HOB
SUGGESTIONS FOR ENVIRONMENT PROTECTION
PRECAUTIONS AND GENERAL ADVICE
ENERGY SAVING TIPS
CARE AND MAINTENANCE
AFTER-SALES SERVICE
INSTALLATION
PRODUCT DESCRIPTION SHEET
2
BEFORE USING THE COOKING HOB
• To get full satisfaction of your cooking hob,
please read these instructions carefully and
keep them for future consultation.
•
•
•
Keep the packaging material (plastic bags, polystyrene parts, etc.) out
of the reach of children, as they are potentially dangerous.
Check whether the cooking hob has been damaged during transport..
Ensure that the installation and electrical connections are
performed by a qualified technician, following the manufacturer’s
instructions and in compliance with current local safety
regulations..
SUGGESTIONS FOR ENVIRONMENT PROTECTION
Packing
The packaging material is entirely recyclable, and is marked with therecycling
symbol , which identifies it as a type of material that must be sent to local
waste-disposal centres.
electronic appliances. Disposal must be carried out in accordance with local
environmental regulations for waste disposal.For further information on the
treatment, recovery and recycling of this appliance, contact your competent
local authority, the collection service for household waste or the shop where
you purchased the appliance.
Domestic appliances
This appliance is marked according to the European Directive 2012/19/EC,
Waste Electrical and Electronic Equipment (WEEE). By ensuring that this
appliance is scrapped suitably, you can help prevent potentially damaging
consequences for the environment and health.
The symbol
on the appliance, or on the accompanying documentation,
indicates that this product must not be treated as household waste, but must
be delivered to the nearest collection centre for the recycling of electrical and
PRECAUTIONS AND GENERAL ADVICE
• Before any cleaning or maintenance operation,disconnect the
cooking hob from mains power supply.
• In case of prolonged use, additional ventilation may be needed
(opening a window or increasing the extraction force of the hood).
• Keep children away from the cooking hob when it is in use.
• The appliance must not be used be people (including children) with
limited physical,sensory or mental abilities, or without experience
or expertise, unless they have received instructions for using it from
those responsible for their safety.
• After use, ensure that the knobs are in position zero.
Declaration of conformity
• This oven is designed to come into contact with food and complies with
regulation (EC) no.1935/2004.
• This cooking hob (Class Y) has been designed to be used only for cooking.
Any other use (such as heating a room) is improper and dangerous.
• This cooking hob has been designed, constructed and marketed in
compliance with:
- the safety requirements of “Low Voltage” Directive 2006/95/EC (replacing
73/23 EEC as amended);
- protection requirements of EEC Directive “EMC” 89/336;
- requirements of EEC Directive 93/68.
ENERGY SAVING TIPS
• The cooking hob is equipped with hotplates having different diameters. Use
pots and pans whose bottom diameter is equal to that of the hotplates, or
slightly larger.
• Only use flat-bottomed pots and pans.
• Do not operate a hotplate without placing a container on it.
• If possible, keep the container covered when cooking.
• Cook vegetables, potatoes, etc. with a small amount of water in order to
cut down cooking time.
• A pressure cooker allows you to save even more energy and time.
3
CARE AND MAINTENANCE
Cleaning the hob
• Before cleaning the cooking hob, disconnect it from mains power
supply and wait until it has cooled down.
• Important: never clean the appliance with steam cleaning equipment.
• Wipe it with a cloth moistened with hot water and soap or diluted liquid
detergent.
• Do not use abrasive or corrosive products, chlorine products or steel wool.
• Do not leave acid or alkaline substances, such as vinegar, salt or lemon
juice, etc., on the cooking hob.
Stainless steel surface
• Clean it with a specific commercial product.
Note: if the cooking hob is used continuously,the high temperatures
may alter the colour of the hotplates.
Cleaning the electric hotplates
The electric hotplates must be cleaned when they are lukewarm. Wipe
them with a cloth moistened with water and salt, and polish with a cloth
moistened with oil.
AFTER-SALES SERVICE
• Before contacting After-sales Service:
1.Re-start the cooking hob, to check whether correct operation has been
restored.
2.If the malfunction persists, call the After-sales Service.
Give the following information:
• type of malfunction;
• model of cooking hob;
• service number (i.e., the number that follows the word SERVICE on the
rating plate under the cooking hob and on the guarantee paper);
• your complete address;
• your telephone number and area code.
INSTALLATION
Technical information for installer
This cooking hob can be embedded in a worktop 20 to 50 mm thick.
If another appliance is not fitted under the cooking hob, insert a separator
panel, at a distance of at least 90 mm from the cooking hob bottom.
• If a vertical piece of furniture is installed, there must be a gap of at
least 100 mm between it and the edge of the cooking hob.
Installation of cooking hob
• Apply the supplied gasket to the cooking hob (unless it has already
been fitted), after having cleaned its surface as shown in the figure.
A - If the worktop is made out of wood, use the springs supplied.
1.Fit the 4 springs A into the relevant seat under the box.
2.Make an opening in the worktop, respecting the dimensions indicated in
the enclosed product description sheet.
3.Install the cooking hob in the worktop.
B- If the worktop is made out of marble or other materials (plastics, ceramics
or stone), the cooking hob must be fixed by means of brackets B to be ordered
from the After-sales Service (code 4819 310 18528).
1.Align the brackets with the bores and fix them with the screws.
2.Make an opening in the worktop, respecting the dimensions indicated in
the product description sheet.
3.Install the cooking hob in the worktop.
• Before installing the cooking hob, remove the plastic film that protects
it, if present. The outer surfaces of the furniture or appliances adjoining
the cooking hob must be heat resistant (heat protection “Y”, according to
standards EN 60335-2-6).
• Installation must comply with current local safety regulations.
4
If any repairs are required, please contact an authorised After-sales Service
as indicated in the warranty. In the unlikely event that an operation or repair
is carried out by an unauthorised technician, always request a certification
of the job carried out and insist on the use of original spare parts. Failure
to comply with these instructions may compromise the safety and
quality of the product.
INSTALLATION
Electrical Connection
• The electrical connections must comply with local regulations.
• The data relevant to the voltage and power absorption are indicated
on the rating plate.
• The earthing of this appliance is compulsory by law. The manufacturer
cannot be held responsible for injury to persons or animals or damage
to property arising from failure to comply with these requirements.
• When the appliance is installed, provide a multi-pole circuit breaker
with a contact separation (at least 3 mm) in all poles that provide
full disconnection under overvoltage category III and must be
incorporated in the fixed wiring in accordance with the national
wiring rules.
• After installation, the electric parts must not be accessible.
• For electrical connection, use an H05RR-F cable (see table in product
description sheet).
• The power cable must be long enough for connecting the appliance,
once fitted in its housing, to the power supply.
• The electrical components must not be accessible to the user after
installation.
ELECTRICAL COOKING HOBS WITH SIDE CONTROLS
Connection to terminal board
1.Open the cover of the terminal board and loosen screw A by means of a
tool, as shown in the figure.
2.Unsheathe the cable for about 70 mm.
3.Peel off the internal cables for about 10 mm loosen cable clamp screw B,
and insert the cable in the cable clamp.
• The terminal board has 4 terminals:
1-2 interconnected (line)
3 (neutral)
4 (earth): marked with symbol
4.Connect the cable to the terminal board, following the indications of
the connection diagram punched on the bottom of the cooking hob.
Fasten the cable clamp and close the cover.
5
PRODUCT DESCRIPTION SHEET
1. Rapid hotplate Ø 180 - 2000 W
2. Normal hotplate Ø 145 - 1000 W
3. Normal hotplate Ø 180 - 1500 W
4
1
4. Normal hotplate Ø 145 - 1000 W
5. Rapid hotplate control knob Ø 180
9
5
6
3
6. Normal hotplate control knob Ø 145
7. Normal hotplate control knob Ø 180
8. Normal hotplate control knob Ø 145
9. Hotplate operation control lamp
7
8
2
Operation of electric hotplates
• Set the knob to one of positions 1-6, which
correspond to different temperatures.
• To switch off the hotplate, set the knob to position “0”.
DIMENSIONS OF COOKTOP AND WORKTOP (mm)
N.B.: In case of installation of a hood above the cooktop, please refer to the hood instructions for the correct distance.
SUPPLY VOLTAGE
220-240V ~ +
CONDUCTORS:
NUMBER AND SIZE
3 x 2,5 mm²
Type PLETP 220-240 ~ 50/60Hz 5,5 kW
6
ELECTRICAL
CONNECTION
7
400011190697
8
EN
10/17
">
