advertisement
user manual
Ceramic glass induction hob
GK69TSIO
2
electrolux
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
Contents
Safety Information
Description of the appliance
Operating the appliance
Tips on cooking and frying
Cleaning and care
2
3
5
10
11
Disposal
What to do if ...
Installation Instructions
Service
12
12
14
17
Safety Information
Warning!
Please comply with these instructions. If you do not, any damage resulting is not covered by the warranty.
Correct use
• This appliance is not intended for use by children or other persons whose physical, sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction by a responsible person to ensure that they can use the appliance safely.
• Do not leave the appliance unattended during operation.
• This appliance should be used only for normal domestic cooking and frying of food.
• The appliance must not be used as a work surface or as a storage surface.
• Additions or modifications to the appliance are not permitted.
• Do not place or store flammable liquids, highly inflammable materials or fusible objects (e.g. plastic film, plastic, aluminium) on or near the appliance.
Children’s safety
• Small children must be kept away from the appliance.
• Only let bigger children work on the appliance under supervision.
• To avoid small children and pets unintentionally switching the appliance on, we recommend activation of the child safety device.
Subject to change without notice
General safety
• The appliance may only be installed and connected by trained, registered service engineers.
• Built-in appliances may only be used after they have built in to suitable built-in units and work surfaces that meet standards.
• In the event of faults with the appliance or damage to the glass ceramic (cracks, scratches or splits), the appliance must be switched off and disconnected from the electrical supply, to prevent the possibility of an electric shock.
• Repairs to the appliance must only be carried out by trained registered service engineers.
Safety during use
• Remove stickers and film from the glass ceramic.
• There is the risk of burns from the appliance if used carelessly.
• Cables from electrical appliances must not touch the hot surface of the appliance or hot cookware.
• Overheated fats and oils can ignite very quickly. Warning! Fire hazard!
• Switch the cooking zones off after each use.
• Users with implanted pacemakers should keep their upper body at least 30 cm from induction cooking zones that are switched on.
• Risk of burns! Do not place objects made of metal, such as knives, forks, spoons and saucepan lids on the cooking surface, as they can get hot.
electrolux
3
Safety when cleaning
• For cleaning, the appliance must be switched off and cooled down.
• For safety reasons, the cleaning of the appliance with steam jet or high-pressure cleaning equipment is not permitted.
How to avoid damage to the appliance
• The glass ceramic can be damaged by objects falling onto it.
• The edge of the glass ceramic can be damaged by being knocked by the cookware.
• Cookware made of cast iron, cast aluminium or with damaged bottoms can
Description of the appliance
Cooking surface layout
1 2
6 5 4 3
1 Induction cooking zone 2300W, with power function 3200W
2 Induction cooking zone 2300W, with power function 3200W
3 Control panel
4 Induction cooking zone 2300W, with power function 3200W
5 Induction cooking zone 2300W, with power function 3200W scratch the glass ceramic if pushed across the surface.
• Objects that melt and things that boil over can burn onto the glass ceramic and should be removed straightaway.
• Do not use the cooking zones with empty cookware or without cookware.
• To avoid damaging cookware and glass ceramics, do not allow saucepans or frying pans to boil dry.
• The ventilation gap of 5mm between the worktop and front of the unit underneath it must not be covered.
6 Control panel
The cooking surface is divided into four cooking zones. In each cooking zone under the glass ceramic is an induction heating element, the middle of each one being marked with a cross on the glass ceramic surface.
Cookware can be placed on any of the cooking zones. But the cross must be completely covered by the cookware. The bottom of the cookware must be from 125 - 210 mm in diameter.
Cooking over two cooking zones
Large cookware can be heated with two cooking zones simultaneously. Either the two cooking zones on the left-hand side or on the right-hand side of the cooking surface are suitable for this.
1. Place cookware centrally on the two zones.
The cookware must cover at least two crosses.
2. Set the same heat setting for the two cooking zones (max. setting 8).
With different cookware there can be differences in the heat distribution. Good cooking results can be achieved with cookware with thick, flat bottoms.
4
electrolux
Control panel layout
9
8
7
6
3
4
5
1
2
2 Stop+Go with a pilot light
3 On/Off with indicator
4 Heat setting indicator
5 Power function
6 Heat setting selection
7 Timer
8 Timer display
9 Cooking zone indicators - Timer function
1 Child lock with a pilot light
Touch Control sensor fields
The appliance is operated using Touch Control sensor fields. Functions are controlled by touching sensor fields and confirmed by displays and acoustic signals. Only touch the sensor fields which activate a desired function. Do not cover other sensor fields.
Sensor field
On / Off
If the control bar is touched for longer than 6 seconds, a signal sounds and the appliance switches itself off.
Function
Switches appliance on and off
Child lock Locking control panel for children
STOP+GO
Power
Timer
Increase settings
Reduce settings
To switch the Keep Warm setting on/ off
Switching the power function on and off
Timer selection
To increase Timer time
To reduce Timer time
Displays
electrolux
5
-
+ digit
Display
Keep Warm settings
Heat settings
Auto Warm-up
Fault
Pan detection
Residual heat
Child safety device
Power
Automatic Switch off
Residual heat indicator
Warning!
Risk of burns from residual heat. After being switched off, the cooking zones need some time to cool down. Look at the residual heat indicator
.
Description
The cooking zone is switched off
Keep Warm / STOP+GO function is switched on
To set heat settings
The Auto Warm-up function is switched on
Malfunction has occurred
Cookware is unsuitable or too small or no cookware has been placed on the cooking zone
Cooking zone is still hot
Lock/Child safety device is set
Power function is switched on
Switch off is active
Residual heat can be used for melting and keeping food warm.
The
induction cooking zones
create the heat required for cooking directly in the base of the cookware. The glass ceramic is merely heated by the residual heat of the cookware.
Operating the appliance
Use the induction cooking zones with suitable cookware.
Switching the appliance on and off
Switch on
Switch off
Control panel
Touch for 1 second
Touch for 1 second
Display
/
/ none
Pilot light
lights up.
goes out.
After switching on, within approx. 10 seconds a heat setting or a function must be set, otherwise the appliance automatically switches itself off.
Setting the heat setting
To set the heat setting
Switch off
Control panel
Touch the desired heat setting, if necessary, correct up or down
Touch
Locking/unlocking the control panel
The control panel, with the exception of the
“On/Off” sensor field, can be locked at any
/
Display
to time in order to prevent the settings being changed e.g. by wiping over the panel with a cloth.
To switch on
To switch off
Control panel
Touch
Touch
(for 4 seconds) previously set heat setting
Display
6
electrolux
Turning the STOP+GO function on and off
When you switch the appliance off, the locking function is automatically switched off.
mode then back to the heat setting they were at before
The STOP+GO function simultaneously toggles all active cooking zones to keep-warm
To switch on
Control panel Display
Touch
To switch off
Touch
Previous heat setting (not automatic warm-up or power function)
STOP+GO does not stop timer functions.
STOP+GO controls the entire control panel apart from the sensor field .
heat setting using the automatic warm-up function, the cooking zone switches to full power for a certain amount of time and then automatically switches back to the heat setting set.
Using the automatic warm-up function
All cooking zones are equipped with an automatic warm-up function. When setting a
Step Control Panel
1.
2.
Touch
Move your finger down from
to select the desired heat setting between and
Display
/ after 5 seconds . As long as is displayed, the appliance works at full power. After the automatic warm up is completed, the heat setting / is displayed again.
The length of time that the automatic warm up function operates depends on the heat setting selected.
Heat setting Length of the automatic warm up [min:sec]
0:12
0:12
1:21
3:07
4:24
5:51
8:12
10:12
10:36
2:01
2:01
2:28
2:52
---
electrolux
7
Using the child safety device
The child safety device prevents unintentional use of the appliance.
Switching on the child safety device
Step Control panel
1.
Switch on appliance. Do not set a heat setting.
2.
Touch for 4 seconds
The child safety device is switched on.
Switching off the child safety device
1.
Step Control panel
Switch on appliance. Do not set a heat setting.
2.
Touch for 4 seconds
3.
Switch appliance off.
The child safety device is switched off.
The child safety device can only be switched on and off if no heat setting is set.
Display/Signal
Display/Signal
lights up
Overriding the child safety device
The child safety device can be switched off in this way for a single cooking session; it remains activated afterwards.
1.
Step Control panel Display/Signal
Switch appliance on
2.
Touch for 4 seconds lights up
Until the appliance is next switched off, it can used as normal. After switching off the appliance, the child safety device is active again.
After overriding the child safety device, a heat setting or a function must be set within approx. 10 seconds, otherwise the appliance automatically switches itself off.
to bring a large quantity of water to the boil quickly. The power function is activated for 8 minutes at most. After that the induction cooking zone automatically switches back to heat setting .
Switching the power function on and off
The power function makes more power available to the induction cooking zones, e.g.
Control panel
To switch on
To switch off
Touch
Touch a heat setting
/
Display
8
electrolux
Power Management
The cooking zones of the cooking surface have a maximum power.
The maximum power is reached when the heat setting 13 has been set for all cooking zones.
Two cooking zones generate a pair (see figure) and therefore, the power management shares the maximum available power between these cooking zones.
Using the timer
When the power function is selected for one cooking zone, the power management makes the additional power for this cooking zone available by reducing the power of the corresponding other cooking zone.
Example: the heat setting 13 is selected on one cooking zone. The power function is switched on for the corresponding cooking zone. The power function is carried out but the heat setting 13 of one of the cooking zones and the power function for the other cooking zone of the pair exceed the maximum power for both at the same time. For this purpose, the power management reduces the power of the cooking zone that switched on first from 13 to example 5 and the display of this cooking zone changes between 13 and 5 and then stays at the current possible maximum 5 (If the display changes between 13 and 5 or 13 and 3 or another value depends on the type of appliance and the size of the cooking zone).
Function
Automatic cut-out
Condition
a heat setting is set
Outcome after the time has elapsed
acoustic signal
00
flashes
Cooking zone switches off
Countdown timer cooking zones not in use
If just one countdown value is set you can change it only when the appliance is switched on.
acoustic signal
00
flashes the cooking zone is switched off after the time set has elapsed.
If a cooking zone is switched off, the timer function set is also switched off.
If a heat setting is set on this cooking zone in addition to a countdown timer,
Selecting a cooking zone
Step
1.
Control panel
Touch once
Display
Pilot light of the first cooking zone flashes
2.
Touch once
Pilot light of the second cooking zone flashes
3.
4.
Touch once
Pilot light of the third cooking zone flashes
Touch once
Pilot light of the fourth cooking zone flashes
electrolux
9
If other timer functions are set, after a few seconds the shortest remaining time
Setting the time
of all the timer functions is displayed and the corresponding pilot light flashes.
Step
1.
Control panel
Select a cooking zone
2.
Touch or
After a few seconds the pilot light flashes more slowly.
The time is set.
The time counts down.
Switching off the timer function
Display
Pilot light for the cooking zone selected flashes
00
to
99
minutes
Step Control panel Display
1.
2.
Select a cooking zone
Touch
Pilot light of cooking zone selected flashes faster
Time remaining is displayed
The time remaining counts backwards to
00
.
The pilot light goes out.
The Timer function for the selected cooking zone is switched off.
Changing the time
Step
1.
Control panel
Select a cooking zone
2.
Touch or
After a few seconds the pilot light flashes more slowly.
The time is set.
The time counts down.
Displaying the time remaining for a cooking zone
Display
Pilot light of the selected cooking zone flashes more quickly
Remaining time is displayed
01
to
99
minutes
Step
1.
Control panel field
Select a cooking zone
Display
Pilot light of the cooking zone selected flashes faster
The time remaining is displayed
After a few seconds the pilot light flashes more slowly.
Switching off the acoustic signal
Acoustic signal
Acoustic signal to acknowledge.
Step
1.
Touch
Acoustic signal stops.
Control panel field
Automatic switch off
Cooking surface
• If after switching on the cooking surface, a heat setting is not set for a cooking zone within approx. 10 seconds, the cooking surface automatically switches itself off.
• If one or more sensor fields are covered by objects (a pan, etc.) for longer than approx.
10 seconds, a signal sounds and the cooking surface switches off automatically.
• If all cooking zones are switched off, the cooking surface automatically switches itself off after approx. 10 seconds.
10
electrolux
Control panel
• When the appliance is switched off, if one or more of the sensor fields on the control panel are covered for more than 10 seconds, an acoustic signal sounds. The acoustic signal switches itself off automatically when the sensor fields are no longer covered.
Induction cooking zones
• In the case of overheating (e.g. when a saucepan boils dry) the cooking zone automatically switches itself off. is displayed. Before being used again the cook-
Heat setting
1 - 3
4 - 7
8 - 9
10 - 14 ing zone must be set to and allowed to cool.
• If cookware that is not suitable is used,
lights up in the display and after 2 minutes the display for the cooking zone switches itself off.
• If one of the cooking zones is not switched off after a certain time, or if the heat setting is not modified, the relevant cooking zone switches off automatically. is displayed.
Before being used again, the cooking zone must be set to .
Switches off after
6 hours
5 hours
4 hours
1.5 hours
Tips on cooking and frying
Information about acrylamides
According to the latest scientific research, intensive browning of food, especially in products containing starch,
Cookware for induction cooking zones
Cookware material
Steel, enamelled steel
Cast iron
Stainless steel
Cookware bottom of multilayer
Aluminium, copper, brass
Glass, ceramic, porcelain
* Cookware for induction cooking zones is labelled as suitable by the manufacturer.
Suitability test
Cookware is suitable for induction cooking, if
…
• ... a little water on an induction cooking zone set to the highest heat setting is heated within a short time.
• ... a magnet sticks to the bottom of the cookware.
Certain cookware can make noises when being used on induction cooking zones. These noises are not a fault in the may present a health risk due to acrylamide. Therefore we recommend cooking at low temperatures and not browning foods too much.
Suitable
+*
+*
+
+
-
appliance and do not affect operation in any way.
Bottom of the cookware
The bottom of the cookware should be as thick and level as possible.
Pan size
Induction cooking zones adapt automatically to the size of the bottom of the cookware up to a certain point. However the magnetic part of the bottom of the cookware must have a minimum diameter depending on the size of the cooking zone. Cookware with a bottom with a diameter of less than 12cm is not suitable.
electrolux
11
Tips on energy saving
Place cookware on the cooking zone before it is switched on.
Examples of cooking applications
The information given in the following table is for guidance only.
If possible, always place a lid on the cookware.
0
Heat setting
Cooking process suitable for Cook time Tips/Hints
1-3
1-3
3-5
5-7
7-9
7-9
14
1
9-12
12-13
Melting
Off position
Keeping food warm Keeping cooked foods warm
Hollandaise sauce, melting butter, chocolate, gelatine
Solidifying
Simmering
Fluffy omelettes, baked eggs
Simmering rice and milkbased dishes
Heating up readycooked meals
Steaming
Braising
Boiling
Boiling
Gentle frying
Heavy frying
Boiling Searing
Deep frying as required
5-25 mins.
10-40 mins.
Cover
Stir occasionally
Cook with lid on
Steaming vegetables, fish Braising meat
Steaming potatoes
25-50 mins.
20-45 mins.
20-60 mins.
Add at least twice as much liquid as rice, stir milk dishes part way through cooking
With vegetables add only a little liquid (a few tablespoons)
Use only a little liquid, e. g.: max. ¼ l water for 750 g of potatoes
Up to 3 l liquid plus ingredients
Cooking larger quantities of food, stews and soups
Frying escalope, veal cordon bleu, cutlets, rissoles, sausages, liver, roux, eggs, pancakes, doughnuts
60-150 mins.
as required Turn halfway through cooking
Hash browns, loin steaks, steaks, Flädle (pancakes for garnishing soup)
5-15 mins. per pan Turn halfway through cooking
Boiling large quantities of water, cooking pasta, searing meat
(goulash, pot roast), deep frying chips
The power function is suitable for heating large quantities of liquid.
Cleaning and care
Warning!
Sharp objects and abrasive cleaning agents will damage the appliance. Clean the appliance and remove the residues with water and washing up liquid after each use.
Remove also the remnants of the cleaning agents!
12
electrolux
Scratches or dark stains on the glass ceramic that cannot be removed do not affect the functioning of the appliance.
Cleaning the appliance after each use
1. Food containing sugar, plastics, tin foil residues should be removed at once using a scraper. Place a scraper on the glass ceramic surface at an angle and remove residues by sliding the blade over the surface. Wipe the appliance with a damp cloth and a little washing up liquid.
Finally,
rub the appliance dry using a clean cloth
.
2. Limescale rings, water rings, fat splashes, shiny metallic discolorations should be removed after the appliance has cooled down using cleaner for glass ceramic or stainless steel.
Disposal
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product.
Packaging material
The packaging materials are environmentally friendly and can be recycled.
The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at your local waste disposal facilities.
What to do if ...
Problem/Display
The cooking zones cannot be switched on or are not operating
Display is switching between two heat settings
The residual heat indicator is not displaying anything
Possible Cause
More than 10 seconds have passed since the appliance was switched on
The lock is switched on
Several sensor fields were touched at the same time
Automatic switch-off has been triggered
Remedy
Switch the appliance on again.
The child safety device is switched on
Switch off the lock (See the section “Locking/unlocking the control panel”)
Deactivate child safety device
(see the section "Child safety device")
Only touch one sensor field
Remove any objects (pans, etc.) that are lying on the control panel. Switch appliance on again
Wipe the control panel There is water on the control panel or the control panel is covered with fat splashes
STOP+GO is activated
Power management is reducing the power of this cooking zone
The cooking zone was only on for a short time and is therefore not hot
Switch off STOP+GO
See the section “Switching the power function on and off”
If the cooking zone is supposed to be hot, call your local Service
Force Centre.
electrolux
13
Problem/Display
lights up
Possible Cause
Unsuitable cookware
No cookware on the cooking zone
Diameter of the base of the cookware is too small for the cooking zone
Automatic switch-off has been triggered
Electronics fault
Remedy
Use suitable cookware
Put cookware on zone
Move to smaller cooking zone
Use suitable cookware
lights up
and number are displayed
Switch appliance off. Switch appliance on again
Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house’s wiring system) If after switching on again, is displayed again, call the customer service department
Remove objects.
Acoustic signal sounds when appliance is switched off
Repeated acoustic signal (6x), appliance switches off
The control panel is wholly or partly covered by objects.
One or more sensor fields have been covered for longer than 10 seconds
The On/Off sensor field has been covered up, e.g. by a cloth
Acoustic signal sounds and appliance switches itself on and then off again; after 5 seconds another acoustic signal sounds
If you are unable to remedy the problem by following the above suggestions, please contact your local Service Force
Centre.
Warning!
Repairs to the appliance are only to be carried out by qualified service engineers. Considerable danger to the user may result from improper repairs.
If the appliance has been operated incorrectly, the engineer's visit will be chargeable, even during the warranty period.
Operating noises
Depending on the material and the processing of the base, the following noises may occur when using induction cooking zones.
1
Do not place any objects on the control panel
2 when using cookware made of different materials (Sandwich construction)
• Whistling
1
Uncover sensor field
• Cracking noise
1
3 when using an individual cooking zone or several cooking zones with high powers when the cookware is made of different materials (Sandwich construction)
• Humming
2 can occur at high power levels
• Clicking
2 during electric switching processes
14
electrolux
• Hissing, buzzing
3
The device is fitted with a fan for cooling the electrics. A whiring noise can be heard when operating the fan which may deviate depending on the performance and may
Installation Instructions
Safety instructions
Warning!
This must be read!
The laws, ordinances, directives and standards in force in the country of use are to be followed (safety regulations, proper recycling in accordance with the regulations, etc.)
Installation may only be carried out by a qualified electrician. The minimum distances to other appliances and units are to be observed.
Anti-shock protection must be provided by the installation, for example drawers may only be installed with a protective floor directly underneath the appliance.
The cut surfaces of the worktop are to be protected against moisture using a suitable sealant.
The sealant seals the appliance to the work top with no gap. When building in, protect the underside of the appliance from steam and moisture, e.g. from a dishwasher or oven.
Avoid installing the appliance next to doors and under windows. Otherwise hot cookware may be knocked off the rings when doors and windows are opened.
Warning!
Risk of injury from electrical current.
• The electrical mains terminal is live.
• Make electrical mains terminal free of voltage.
• Follow connection schematic.
• Observe electrical safety rules.
• Ensure anti-shock protection by installing correctly.
• The appliance must be connected to the electrical supply by a qualified electrician.
• Loose and inappropriate plug and socket connections can make the terminal overheat.
continue for a while after the appliance is switched off.
The noises described are normal and do not refer to any defects.
• Have the clamping connections correctly installed by a qualified electrician.
• Use strain relief clamp on cable.
• In the event of single-phase or twophase connection, the appropriate mains cable of type H05BB-F Tmax
90°C (or higher) must be used.
• If this appliance’s mains cable is damaged, it must be replaced by a special cable (type H05BB-F Tmax 90°C; or higher). Please contact your local
Service Force Center for further advice.
A device must be provided in the electrical installation which allows the appliance to be disconnected from the mains at all poles with a contact opening width of at least 3 mm
Suitable isolation devices include line protecting cut-outs, fuses (screw type fuses are to be removed from the holder), earth leakage trips and contactors.
Sticking on the seal
• Clean the worktop in the area of the cutout section.
• Stick the one-sided self-adhesive sealing tape supplied all the way round the lower edge of the cooking surface along the outer edge of the glass ceramic panel. Do not stretch it. The cut ends should lie in the middle of one side. When you have cut it to length (add a few mm), press the two ends flush up against one another.
Sticking the seal to the rabbet
• Clean the rabbet in the work surface.
• Stick the one-sided self-adhesive sealing tape supplied onto the upper surface of the rabbet along the edges of the cut-out section.
• Cut the sealing tape into four pieces relating to the length of the edges of the rabbet.
electrolux
15
• For the four corners of the rabbet the ends of the sealing tapes must be cut into mitres. Do not stick the ends over one another.
• Stick the sealing tape flush into the corner of the rabbet, so that no silicon compound
Assembly
can get under the glass ceramic when grouting.
• Don’t stretch the tapes when sticking them on.
Mounting on the top
600
=
490 +1
=
R5
680 +1 min. 5 min. 20 min. 5
16
electrolux min. 25 min. 5 min. 20
Integrated mounting
R10
R5
7
13
490
516 +1 min. 600
680
706 +1 min. 38 min. 5 min. 38 min. 5 min. 20 min. 25 min. 5
Rating Plate
Modell GK69TSIO Prod. Nr. – 949 593 085
Typ 55GDD D4 AU 230 V, 50 Hz
Electrolux
Service
In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instructions (section “What to do if…”).
If you were not able to remedy the problem yourself, please contact the Customer Care
Department or one of our service partners.
In order to be able to assist you quickly, we require the following information:
– Three-digit-letter combination for glass ceramic
– Model description
– Product number (PNC)
– Serial number
(S No. - see rating plate)
– Type of fault
– Any error messages displayed by the appliance electrolux
17
18
electrolux
electrolux
19
www.electrolux.com
www.electrolux.de
892930343-A-092008
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement