Panasonic PVC2033W Operating Instructions

Panasonic PVC2033W Operating Instructions
Initial Setup
Combination VCR
Operating Instructions
PV-C2023/PV-C2033W
Basic Operation
Model No.
TV Operation
As an ENERGY STAR® Partner,
Matsushita Electric Corporation of America has determined
that this product or product model meets the ENERGY STAR®
guidelines for energy efficiency.
LSQT0665A
Please read these instructions carefully before attempting to connect,
operate, or adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Timer Operation Advanced Operation For Your Information
• Initial Setup and Connection Procedures are on pages 8 and 9.
Important Safeguards and Precautions
READ AND RETAIN ALL SAFETY AND
OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON UNIT
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from power source indicated on unit or
in this manual. If uncertain, have your Electric Utility
Service Company or Video Products Dealer verify
your home power source.
2 POWER CORD PLUG
For safety, this unit has a polarized type plug (one
wide blade), or a three-wire grounding type plug.
Always hold the plug firmly and make sure your hands
are dry when plugging in or unplugging the AC power
cord. Regularly remove dust, dirt, etc. on the plug.
POLARIZED PLUG CAUTION:
The plug fits into outlet one way. If it cannot be fully
inserted, try reversing it. If it still will not fit, have an
electrician install the proper wall outlet. Do not tamper
with the plug.
GROUNDING PLUG CAUTION:
The plug requires a three-hole grounding outlet.
If necessary, have an electrician install the proper outlet.
Do not tamper with the plug.
3 POWER CORD
To avoid unit malfunction, and to protect against
electrical shock, fire or personal injury:
- Keep power cord away from heating appliances and
walking traffic. Do not rest heavy objects on, or roll
such objects over the power cord.
- Do not tamper with the cord in any way.
- An extension cord should have the same type plug
(polarized or grounding) and must be securely
connected.
- Overloaded wall outlets or extension cords is a fire
hazard.
- Frayed cords, damaged plugs, and damaged or
cracked wire insulation are hazardous and should
be replaced by a qualified electrician.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat
generated during operation. If blocked, heat
build-up may result in a fire hazard or heat damage to
cassettes.
For your protection:
a. Never cover ventilation slots while unit is ON, or
operate unit while placed on a bed, sofa, rug, or
other soft surface.
b. Avoid built-in installation, such as a book case or
rack, unless properly ventilated.
5 AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE CHANGES
Do not place unit over or near a heater or radiator, in
direct sunlight, etc. If unit is suddenly moved from a
cold place to a warm place, moisture may condense in
unit and on the tape causing damage.
6 TO AVOID PERSONAL INJURY
• Never place unit on support or
stand that is not firm, level, and adequately strong.
The unit could fall causing serious injury to a child or
adult and damage to the unit.
• Move any appliance and
cart combination with care.
Quick stops, excessive
force, and uneven
surfaces may cause objects to
overturn.
• Carefully follow all operating
instructions.
2
OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION
An outside antenna or cable system must be properly grounded to
provide some protection against built up static charges and voltage.
Section 810 of the National Electrical Code, ANSI/NFPA 70 (in Canada,
part 1 of the Canadian Electrical
Code) provides information
NEC - NATIONAL
ANTENNA LEAD
ELECTRICAL CODE
IN WIRE
regarding proper grounding
ANTENNA
GROUND
DISCHARGE UNIT
of the mast and supporting
CLAMP
(NEC SECTION 810-20)
structure, grounding of the
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC
lead-in wire to an antenna
SERVICE
GROUND CLAMPS
EQUIPMENT
discharge unit, size of grounding
POWER SERVICE
GROUNDING
conductors, location of antenna
ELECTRODE SYSTEM
(NEC ART 250, PART H)
discharge unit, connection
to grounding electrodes, and
requirements for the grounding electrode.
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR
CIRCUITS
Locate an outside antenna system well away from power lines and
electric light or power circuits so it will never touch these power sources
should it ever fall. When installing antenna, absolutely never touch power
lines, circuits or other power sources as this could be fatal.
USING THE UNIT
Before unit is brought out of storage or moved to a new location,
refer again to the INSTALLATION section of these safeguards.
1 KEEP UNIT WELL AWAY FROM WATER OR MOISTURE,
such as vases, sinks, tubs, etc.
2 IF EXPOSED TO RAIN, MOISTURE, OR STRONG IMPACT,
unplug unit and have it inspected by a qualified service
technician before use.
3 ELECTRICAL STORMS
During a lightning storm, or before leaving unit unused for
extended periods of time, disconnect all equipment from the
power source as well as the antenna and cable system.
4 WHEN UNIT IS PLUGGED IN
• DO NOT OPERATE IF:
- liquid has spilled into unit.
- unit was dropped or otherwise damaged.
- unit emits smoke, malodors, or noises.
Immediately unplug unit, and have it inspected by a service
technician to avoid potential fire and shock hazards.
• Never drop or push any object through openings in unit.
Touching internal parts may cause electric shock or fire
hazard.
• Keep magnetic objects, such as speakers, away from unit to
avoid electrical interference.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.
6 CLEANING UNIT
Unplug unit. Use a clean, dry, chemically untreated cloth to
gently remove dust or debris. DO NOT USE cleaning fluids,
aerosols, or forced air that could over-spray, or seep into unit
and cause electrical shock. Any substance, such as wax,
adhesive tape, etc. may mar the cabinet surface. Exposure to
greasy, humid, or dusty areas may adversely affect internal
parts.
SERVICE
1 DO NOT SERVICE PRODUCT YOURSELF
If, after carefully following detailed operating instructions, the
unit does not operate properly, do not attempt to open or remove
covers, or make any adjustments not described in the manual.
Unplug unit and contact a qualified service technician.
2 REPLACEMENT OF PARTS
Make sure the service technician uses only parts specified by
the manufacturer, or have equal safety characteristics as original
parts. The use of unauthorized substitutes may result in fire,
electric shock, or other hazards.
3 SAFETY CHECK AFTER SERVICING
After unit is serviced or repaired, request that a through safety
check be done as described in the manufacture’s service
literature to ensure video unit is in safe operating condition.
Safety Precautions/Mesures de sécurité
Warning :
To prevent fire or shock hazard, do not expose this equipment to rain or
moisture.
Caution :
To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Avertissement : Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer
cet appareil à la pluie ou à une humidité excessive.
Attention :
Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans
la borne correspondante de la prise et pousser jusqu’au fond.
FCC WARNING : Any unauthorized changes or modifications to this equipment would void the
user’s authority to operate.
This video recorder, equipped with the HQ (High Quality) System, is compatible with existing VHS
equipment. Only use those tapes with the
mark. It is recommended that only cassette tapes that
have been tested and inspected for use in 2, 4, 6, and 8 hour VCR machines be used. This television
receiver provides display of television closed captioning in accordance with §15.119 of the FCC rules.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS
INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
This symbol warns the user that uninsulated voltage within the unit
may have sufficient magnitude to cause electric shock. Therefore, it
is dangerous to make any kind of contact with any inside part of this
unit.
This symbol alerts the user that important literature concerning the
operation and maintenance of this unit has been included. Therefore,
it should be read carefully in order to avoid any problems.
This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead. Disposal
of these materials may be regulated in your community due to environmental considerations. For
disposal or recycling information please contact your local authorities, or the Electronics Industries
Alliance: <http://www.eiae.org.>
Congratulations
Accessories
Remote Control
On your purchase of one of the most sophisticated
and reliable products on the market today. Used
properly, it will bring you and your family years of
enjoyment. Please fill in the information below. The
serial number is on the tag located on the back of
your unit.
LSSQ0380
(PV-C2023)
LSSQ0384
(PV-C2033W)
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Batteries 2 “AA”
Model No.
Serial No.
Loading the Batteries
Battery replacement caution
• Do not mix old and new batteries.
• Do not mix alkaline with manganese batteries.
To order accessories,
call toll free 1-800-332-5368.
Prevent Accidental Tape Erasure
Break off the tab to
prevent recording.
To record again.
Record
Tab
Cover the hole
with cellophane tape.
Screwdriver
3
Unit Information
Head Cleaning
Specifications
Playing older or damaged tapes may eventually
cause video heads to become clogged.
Display
Picture Tube
Head Clog Sensor
During playback this
screen appears if clogging
is detected. To remove
screen, press PLAY on the
remote or unit.
V I DEO HEADS MAY
NEED CLEAN I NG
PL EASE I NSERT HEAD
CLEAN I NG CASSETTE
OR REFER TO MANUAL
END : PLAY
• Use “dry” type head
cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)
• Follow cleaning tape directions carefully.
Excessive use of head cleaning tape can shorten
the video head life.
Features for a Quality Picture
Digital Auto Tracking
Continuously analyzes the signal and adjusts for
optimum picture quality.
Manual Tracking Control (to reduce picture noise)
Use during Playback and Slow Motion mode to
reduce picture noise. Press the 3 or 6 number key
on the remote control or CH
on the unit until
the picture clears up. To return to Auto Tracking,
press POWER off, then on again a few seconds
later.
Record/Playback Time
Only use tapes with the
Tape Speed
Setting
mark in this unit.
Type of Video Cassette
T60
T120
T160
SP
(Standard
Play)
1 Hour
2 Hours
2 Hours
40 Minutes
LP
(Long Play)
2 Hours
4 Hours
5 Hours
20 Minutes
SLP
(Super Long
Play)
3 Hours
6 Hours
8 Hours
VCR
Video Recording
System
Audio Track
Tuner
Broadcast Channels
CABLE Channels
FM Radio
Band Range
General
Power Source
Power
On
Power
Consumption Power
Off
Television System
Speaker
Operating
Temperature
Operating Humidity
Weight
Dimensions
(W X H X D)
20 inch measured diagonal 90°
deflection Picture Tube
2 rotary heads helical scanning
system
1 track
VHF 2 ~ 13, UHF 14 ~ 69
Midband A through I (14 ~ 22)
Superband J through W (23 ~
36) Hyperband AA ~ EEE (37
~ 64) Lowband A-5 ~ A-1 (95
~ 99) Special CABLE channel
5A(01) Ultraband 65 ~ 94, 100
~ 125
87.5 MHz ~ 108.1 MHz
120 V AC, 60 Hz
Approx. 110 W
Approx. 2.5 W
EIA Standard NTSC color
1 pieces
5 °C ~ 40 °C (41 °F ~ 104 °F)
10 % ~ 75 %
23 Kg (50.6 lbs.)
515 mm (20-5/16″) X 505 mm
(19-7/8″) X 474 mm (18-11/16″)
Note
• Designs and specifications are subject to change
without notice.
DST (Daylight Saving Time)
Unit auto adjusts clock for DST (Daylight Saving
Time.)
■ Spring (First Sunday in April)
DST: ON ➞ Sets clock ahead one hour.
■ Autumn (Last Sunday in October)
DST: OFF ➞ Turns clock back one hour.
• If your area does not observe Daylight Saving Time,
select DST: OFF.
• Keep these time changes in mind when
programming the unit for timer recordings.
4
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Table of Contents
Tape Operation ...................................................................................... 24
Special VCR Features ........................................................................... 28
V-Chip Control Feature ......................................................................... 29
On-Screen Display (OSD) ..................................................................... 32
Before Requesting Service................................................................... 33
Limited Warranty ................................................................................... 34
Customer Services Directory ............................................................... 35
Spanish Quick Use Guide/Guía para rápida consulta........................ 36
Index ....................................................................................................... 40
Timer Operation Advanced Operation For Your Information
Timer Recording .................................................................................... 22
TV Operation
TV Operation .......................................................................................... 14
Picture Adjustment................................................................................ 15
TV Timer Features ................................................................................. 16
Closed Caption System ........................................................................ 18
FM Radio ................................................................................................ 20
Basic Operation
Reset Language, Channels, Clock, Time Zone Adjust....................... 10
Playback a Tape..................................................................................... 12
Record On a Tape.................................................................................. 12
Copy Your Tapes (Dubbing) ................................................................. 13
Initial Setup
Important Safeguards and Precautions ................................................ 2
Safety Precautions/Mesures de sécurité............................................... 3
Unit Information....................................................................................... 4
Location of Controls ............................................................................... 6
Connections/Initial Setup (Ready to Play) ............................................ 8
5
Location of Controls
Remote Control Buttons
SLEEP
EJECT
Ejects tape.
POWER
Turns on or off the unit.
Turns off the unit automatically.
NIGHT
Color and picture intensity level are
adjusted during night time use.
FM/TV
DISPLAY
Receives FM radio signal.
Displays the VCR status and clock.
MUTE
RAPID TUNE
Mutes the sound instantly.
CHANNEL UP/DOWN
Selects a channel.
SELECT UP/DOWN
Controls navigation around
on-screen menu.
ACTION
Displays the last channel you were
watching.
VOLUME UP/DOWN
Adjusts volume.
SET/BACK SPACE
Sets a selected menu, or goes
back to correct.
Displays Main Menu.
PROGRAM
NUMBER Keys
Selects a channel directly.
Displays SET PROGRAM screen.
You can set Timer Program and
On-Timer.
PLAY
TRACKING UP/DOWN
Begins playback.
Reduces picture noise during
Playback and Slow Motion.
REWIND/SEARCH
Rewinds tape, and
searches reverse scene.
PAUSE/SLOW
Pauses and slow motion
and frame advance picture.
CM SKIP/ZERO SEARCH
In Stop mode, goes to the
counter “0:00:00.” In Play
mode, skips over 1 to 3
minutes of tape.
ADD/DELETE
Adds or deletes a channel.
FAST FORWARD/SEARCH
Fast forwards tape, and searches
forward scene.
SEARCH
Goes directly to the desired
recording. Locates end point of
recording.
TAPE POSITION
STOP
Finds out present tape
position and amount of tape
remaining.
REC
Stops recording or playback.
Records the program.
SPEED
Selects recording speed.
COUNTER RESET
Resets to “0:00:00” at the desired
position.
Note
• When EJECT is pressed, the tape is ejected from Cassette Compartment.
If EJECT is pressed during recording, the unit will not respond to the command.
6
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Front View of the Unit and Indicators
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
Initial Setup
POWER
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
Built-In Speaker
PHONES Jack
Connect an
earphone or
headphones.
AUDIO VIDEO IN Jack
For dubbing.
POWER
REWIND/SEARCH
See previous page.
ACTION
Press together with STOP.
PROG TIMER
Indicator
VOLUME UP/DOWN
SET/BACK SPACE
PLAY
See previous page.
REPEAT
Lights when the
unit is set for
Timer Recording.
See previous page.
CHANNEL UP/DOWN
TRACKING UP/DOWN
SELECT UP/DOWN
See previous page.
STOP/EJECT
See previous page.
ACTION
Press together with REW.
See previous page.
Repeats a recording.
ON TIMER
Indicator
FAST FORWARD/
SEARCH
Lights when the
On-Timer is set.
See previous page.
REC Indicator
REC
See previous page.
Lights during
recording.
TIMER/FM
Remote Sensor
Sets a timer alarm up 60 min.
Enables FM Radio.
Rear View of the Unit
VHF/UHF
AC Power Plug
When plugged into an AC outlet, the
unit consumes 2.5 W of electric power
in OFF condition.
VHF/UHF Antenna Input Terminal
In from your Antenna or Cable (See
page 8).
7
Connections/Initial Setup (Ready to Play)
Please make all cable or antenna connections before power on.
Connecting
For ANT./Cable
Connect the cable from Antenna/Cable
to the VHF/UHF terminal on the unit.
UNIT (rear view)
VHF/UHF
VHF/UHF
For DSS/Cable Box
Connect the OUT jack on your cable
box to the VHF/UHF terminal on the unit
with a RF cable.
IN from
ANT./CABLE
VHF/UHF
UNIT (rear view)
Cable TV
Converter Box
VHF/UHF
WARNING:
Overtightening “Nut type” RF coaxial cables
may damage jacks. Finger tighten only.
VHF/UHF
IN from
ANT./CABLE
VHF/UHF
Initial Setup (Ready to Play)
Press COMBO on the remote for Combo mode.
1
2
Plug the unit power cord into AC wall
outlet.
Press POWER on the remote or unit.
The unit comes on and auto channel and
clock set starts.
• If you use a cable box, turn
it on and set it to the Public
Broadcasting Service (PBS)
channel in your time zone.
If you use a DSS receiver, it
must be turned off.
If AUTO CLOCK SET IS INCOMPLETE screen
appears, set the clock using MANUAL CLOCK
SET procedure on next page.
AUTO CLOCK SET
IS INCOMPLETE
CH AUTO SET PROCEEDING
PLEASE SET CLOCK BY
PRESSING ACTION KEY
AUTO CLOCK SET
PROCEEDING
CANCEL : STOP
3
Settings are made automatically. When
setup is done, this screen appears.
2 / 6 / 2003 THUDST
12 ::00PM
ON
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
8
Notes
• Function buttons are inoperative during Initial
Setup.
• To remove a cassette during Auto Set, press
EJECT twice on the remote or STOP twice on
the unit. In this case, settings must be made
manually. (See page 10.)
• Depending on conditions, Auto Clock Set may
take longer than 30 minutes. If so, press STOP
to stop setup and perform settings manually.
(See page 10.)
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Manual Clock Set
Reset all unit Memory Functions
When moving unit to a new location, or if a mistake
was made in the Initial Setup section.
• Make sure a tape is not inserted in the unit.
1
Press ACTION on the remote to display
SET CLOCK Menu screen.
Initial Setup
If AUTO CLOCK SET was incomplete, manually
set the clock as follows.
SET CLOCK
:
1/ /
DST : ON
SELECT :
END
: ACT I ON
2
SET :
Press
to select the month and
press to set. In the same manner,
select and set the date, year, time, and
DST. (Daylight Saving Time)
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
SET CLOCK
2 / 6 / 2003 THU 12: 00PM
DST : ON
1
Turn the unit
Power on.
2
Press and hold both
PLAY/REPEAT and FF on the
unit for more than 5 seconds.
SET COMPLETED
SET
:
START : ACT I ON
3
• The power will shut off.
• Please ignore “NO CASSETTE”
warning.
Press ACTION twice to start CLOCK and
exit.
3
Do “Initial Setup” on page 8.
POWER
ACTION
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
Note to CABLE System Installer
This reminder is provided to call the CABLE
(Cable TV) System Installers attention to
Article 820-40 of the NEC that provides
guidelines for proper grounding and, in
particular, specifies that the cable ground
shall be connected to the grounding system
of the building, as close to the point of cable
entry as practical.
9
Reset Language, Channels, Clock,
1
Press ACTION to display
M A I N MENU
LOCK LANGUAGE
TV
CH
CLOCK
MAIN MENU.
EX I T
SELECT :
SET
: ACT I ON
2
Language
1) Press
to
select language
icon.
EX I T
CLOCK
SELECT :
SET
: ACT I ON
MENU PR I NC I PAL
HOLA
BLOQUEO IDIOMA
CANAL
REL OJ
MENU
BONJOUR
BLOCAGE
LANGUE
CANAL HORLOGE SORT I E
SEL.
:
REGLER : ACT I ON
For French
M A I N MENU
CH
HELLO
LOCK LANGUAGE
CLOCK
CH
LOCK LANGUAGE
CLOCK
EX I T
TV
CH
LOCK LANGUAGE
CLOCK
EX I T
SELECT :
SET
: ACT I ON
2) Press ACTION.
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
WEAK S I GNAL D I SPLAY : OFF
SELECT :
END
: ACT I ON
For Spanish
TV
TV
2) Press ACTION.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
SAL I R
ELEG I R :
F I JAR : ACT I ON
TELE
M A I N MENU
SELECT :
SET
: ACT I ON
2) Press ACTION
repeatedly.
TV
1) Press
to
select “CLOCK.”
M A I N MENU
LOCK LANGUAGE
CH
to
1) Press
select “CH.”
M A I N MENU
TV
Clock
Channels
EX I T
SELECT :
SET
: ACT I ON
SET :
3) Press
to select
“ANTENNA,” then
press to set your
antenna system
(“TV” or “CABLE”).
4) Press
to select
“AUTO SET,” then
press .
• After Channel Auto Set is
finished, Clock Auto Set
will be performed. (If clock
is set manually, Clock Auto
Set will not be performed.)
SELECT :
END
: ACT I ON
SET :
(“TIME ZONE ADJUST” appears
only when auto clock is set.)
3) Press
to select
“MANUAL” or “AUTO
CLOCK SET” and
press .
• For Auto Clock Set, select
“AUTO CLOCK SET,” then
press .
SET CLOCK
2 / 6/2003 THU 12: 00PM
DST : ON
SELECT :
START : ACT I ON
SET :
For English
3) Press
to select “EXIT.”
Press ACTION
to exit.
10
4) Press
and
press
to select and
set the month, date, year,
time, and DST (Daylight
Saving Time).
5) Press ACTION twice to
start the clock and exit
this mode.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Time Zone Adjust
POWER
Time Zone Adjust
(Only when Auto Clock is set.)
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
ACTION
NUMBER Keys
ADD/DLT
M A I N MENU
LOCK LANGUAGE
TV
CLOCK
CH
EX I T
Basic Operation
1) Press
to
select “CLOCK.”
SELECT :
SET
: ACT I ON
2) Press ACTION.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
ACTION key on
the unit
Using
STOP/EJECT REW/
SELECT :
END
: ACT I ON
keys
VOL
CH
SET :
ACTION
3) Press
to
select TIME ZONE
ADJUST and
press repeatedly
to select mode.
(See below.)
+1
0
-1
On Unit
You can operate the
menu screen using
unit buttons. To display
the menu, press
STOP/EJECT and
REW together with no
tape inserted. To exit
the menu, repeat above
with or without tape
inserted until normal
screen appears.
On Remote
On Unit
: CH UP
: CH DOWN
: VOLUME UP
: VOLUME DOWN
Whenever the menu or program
screen is displayed, CHANNEL
and
UP/DOWN function as
VOLUME UP/DOWN function
only.
as
SET CLOCK
Add or Delete a Channel
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : +1
SELECT :
END
: ACT I ON
SET :
To add channel:
To delete channel:
Select channel with
number keys and
press ADD/DLT.
Select channel with
or number keys
CH
and press ADD/DLT.
CHANNEL 08 ADDED
CHANNEL 08 DELE TED
4) Press ACTION
twice to exit.
11
Playback a Tape
Ready Check List
All connections are made.
Your unit is plugged in.
1
Insert a cassette.
• The unit power comes
on automatically.
Record tab
Record On a Tape
1
Insert a cassette with record tab
2
Press CH
channel.
3
Press SPEED to select
recording speed (see page 4).
SP = Standard Play
LP = Long Play
SLP= Super Long Play
To prevent tape jam,
remove loose or peeling
labels from tapes.
2
• Playback begins if cassette has no record
tab.
■ Forward/Reverse scene search
➞ Press FF or REW
➞ Press PLAY to release.
■ Still (Freeze) picture
➞ Press PAUSE/SLOW
➞ Press PLAY to release.
■ Slow Motion picture
➞ Hold down PAUSE/SLOW in
Still mode
➞ Press PLAY to release.
■ Frame by Frame picture
➞ Press PAUSE/SLOW in Still mode
➞ Press PLAY to release.
Notes
• These features work best in SLP mode.
• After the unit is in Still or Slow mode for 3 minutes, it
will switch to Stop mode automatically to protect the
tape and the video head.
■ Stop ➞ Press STOP
■ Rewind tape ➞ Press REW in Stop mode
■ Fast forward tape ➞ Press FF in Stop
mode
■ Eject tape ➞ Press EJECT on the remote
or STOP/EJECT on the unit
You can operate on the unit
CH
PLAY
Insert a cassette.
REC
POWER
VOL
or number keys to select a
• For “LINE” input, see bottom of next page.
• Selected speed is displayed.
Press PLAY.
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
• The unit power comes on automatically.
AUDIO IN
ACTION
4
Press REC to start recording.
• To edit out unwanted portions, press
PAUSE/SLOW to pause and resume recording.
• You cannot view another channel during
recording.
■ Stop ➞ Press STOP
■ One Touch Recording (OTR)
Press REC repeatedly Normal Rec
to set the recording
length (30 min. - 4 hours). 4:00 3:00
0:30
2:00
1:00
1:30
• The unit stops recording at a preset time.
• PROG TIMER indicator lights on the unit.
Notes
• After the unit has been in Rec Pause mode for 5
minutes, it will stop automatically to protect the tape
and the video head.
• The remaining recording time of an OTR can be
displayed by pressing DISPLAY.
EJECT
DISPLAY
ACTION
NUMBER
Keys
REW
PAUSE/
SLOW
PLAY
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
TRACKING
ADD/DLT
FF
STOP
REC
SPEED
■ Press to stop and/or
eject tape.
12
REC Indicator
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
e
Copy Your Tapes (Dubbing)
Connections you’ll need to make.
Recording (Editing) unit
Playing (Source) VCR
AUDIO VIDEO IN FROM ANT.
OUT
VIDEO IN AUDIO IN
Playback (Source)
1
2
3
Insert blank tape
with record tab.
Insert
pre-recorded
tape.
• Dubbing tapes protected with
Copy Guard will have poor
quality results.
Select “LINE” mode.
See “Selecting Input Mode” below.
Press PLAY then
Press REC, then
PAUSE at starting
PAUSE/SLOW
point to put in
immediately to put in
Standby mode.
Standby mode.
(Perform operation of steps 4 and 5 on both units at same time.)
4
5
Recording (Editing) unit
Basic Operation
OUT TO TV
IN
STOP
Press PLAY
to start dubbing.
Press PAUSE/SLOW
to start dubbing.
Press STOP
to stop dubbing.
Press STOP
to stop dubbing.
Selecting Input Mode
Method 1:
Press CH
Caution
• Unauthorized exchanging
and/or copying of copyrighted
recordings may be copyright
infringement.
. The display will change as follows.
1
LINE
2
3
(CABLE) (TV)
125 or 69
Method 2:
a Press ACTION for MAIN MENU.
b Press
to select “TV,” then press
ACTION for SET UP TV screen.
c Press
to select “INPUT SELECT,” and then
press to select “TUNER” or “LINE.”
d Press ACTION twice to exit this mode.
13
TV Operation
1
Press POWER on the remote or unit.
Ready Check List
All connections are made.
Your unit is plugged in.
2
CH 08
Use CH
or number
keys to select
a channel.
Press VOL + or
VOL - to adjust
volume.
3
24
VOL + / VOL-
NIGHT Mode
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
Color and picture intensity levels are adjusted so
the screen is easier on your eyes during night time
use.
NIGHT
Press NIGHT to
set NIGHT mode.
CH
POWER
PHONES
Jack
• NIGHT mode may be
selected when watching
TV or playing a tape.
Press NIGHT to
cancel.
• Previous settings are
restored.
• NIGHT mode is canceled
when power is turned
off or power failure
occurs.
■ Using the 100 key
When selecting CABLE channels 100 to 125 with the number keys, first press the 100
key, and then enter the remaining two digits.
■ Rapid Tune
Press R-TUNE to display the last channel you were watching.
■ Audio Mute
Press MUTE to instantly mute the sound. Press again to restore the previous sound level.
■ Phones
Connect an earphone (not supplied) or headphones (not supplied) to the Phones Jack.
14
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Picture Adjustment
1
2
NIGHT
MUTE
CH
ACTION
VOL
UP/DOWN
NUMBER
Keys
TV
LOCK LANGUAGE
EX I T
CLOCK
1) Press
to select “TV.”
2) Press ACTION
to display SET
UP TV screen.
SELECT :
SET
: ACT I ON
3
SET UP TV
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
FM ANTENNA
SELECT :
END
: ACT I ON
4
: TUNER
: EXT
1) Press
to
select VIDEO
ADJUST.
to
2) Press
display screen.
SET :
COLOR
T I NT
BR I GHTNESS
P I CTURE
SHARPNESS
NORMAL
SELECT :
ADJUST :
END
: ACT I ON
1) Press
to
select an
adjustment
item. (See
below left.)
to
2) Press
adjust.
TV Operation
100 Key
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
M A I N MENU
CH
RAPID
TUNE
POWER
Press ACTION to display MAIN MENU.
COLOR
T I NT
BR I GHTNESS
P I CTURE
SHARPNESS
NORMAL
SELECT :
END
: ACT I ON
Picture Adjustment
SET :
To Reset Picture Controls,
press
and
to select and set “NORMAL.”
All controls return to their factory settings.
■ COLOR Control
Adjust color intensity.
■ TINT Control
Adjust for natural flesh
tones.
5
Press ACTION three times to exit.
■ BRIGHTNESS Control
Adjust picture brightness.
■ PICTURE Control
Adjust picture intensity by
adjusting both contrast and
color level in the proper
balance.
■ SHARPNESS Control
Adjust picture sharpness.
15
TV Timer Features
ON-TIMER with Alarm
This unit can be set to automatically power on in one of 3
modes (TV, Playback, or FM radio).
You can also combine the On-Timer with a one minute
alarm that gradually increases in volume.
1
Ready Check List
The clock is set to the correct time.
Press PROG to display SET PROGRAM screen.
2
1) Press
to select “ON
TIMER.”
2) Press to display ON
TIMER screen.
SET PROGRAM
T I MER PROGRAMMING
ON TIMER
SELECT :
END
: PROG
SET :
1) Press
to select
desired settings.
2) Press to set the
ON-TIMER TIME or
ON-TIMER mode.
ON T I MER
3
6:--AM CH -ALARM : ON
SELECT :
END
: PROG
SET :
TIMER/FM
• Make sure a tape is inserted if Playback mode is selected.
• See “FM Radio” on pages 20 and 21 for instructions on how to
preset FM stations.
CH02
CH03
CH125
CH01
PLAY
FM9
4
FM8
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
• ON-TIMER mode
selection order
VIDEO IN
AUDIO IN
ACTION
FM1
ON T I MER
6:00AM CH08
Press
to select
ALARM “ON” or “OFF.”
CH
ON TIMER
indicator
ALARM : ON
CANCEL : ADD / DLT
SET :
SELECT :
END
: PROG
When “ON” is selected, an alarm will gradually increase
in volume for one minute or until canceled by pressing any
button (including VOL + -).
and
to move back
To Make Corrections, use
and correct.
5
Press PROG to set ON TIMER.
• “ON TIMER SET” is displayed.
• ON TIMER Indicator lights on the unit.
Note
To Cancel ON-TIMER,
Repeat steps 1 and 2. Then, press ADD/DLT to clear the
time in step 3. Now, press PROG to end.
“ON TIMER END” briefly appears on-screen.
16
• If no button on the remote or unit
(including a button used to turn
off the alarm) is pressed within 60
minutes after unit turns itself on,
it will turn itself back off.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Sleep Timer
This unit can be set for auto power off.
SLEEP
DISPLAY
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
PROG
ADD/DLT
Press SLEEP repeatedly
to set SLEEP TIMER.
• Pressing DISPLAY with sleep timer
set displays remaining time.
Press SLEEP repeatedly until
“SLEEP TIMER 00” appears to
cancel.
SLEEP TIMER 30
SLEEP TIMER 60
SLEEP TIMER 90
SLEEP TIMER 00
Instant Alarm
You can set a timer alarm up to 60 min. Useful when you
are cooking, etc.
00:00
• Pressing TIMER/FM repeatedly on the unit will
change display as follows.
One-minute
increase until 10:00
9:00
TV
10:00
20:00
(or LINE)
TV(or LINE)
FM
INSTANT ALARM
Screen Display
FM
To cancel, press TIMER/FM then press ADD/DLT on
the remote while CANCEL/SET screen is displayed.
30:00
50:00
INSTANT ALARM
Screen Display
Five-minute
increase until 30:00
25:00
40:00
in the order shown
left.)
Remaining Time
2:00
15:00
Press CH
on the
unit with CANCEL/SET
screen displayed to set
alarm. (Time changes
5 : 20PM
CANCEL : ADD / DLT
02 : 00
SET : CH
KEY ON UN I T
1:00 (one minute)
3:00
Press TIMER/FM on the unit to display the instant
alarm CANCEL/SET screen.
TV Operation
1
2
To increase timer in progress, repeat step 2. Time
will be rounded up to next 1, 5, or 10 minute interval.
(See chart left.)
Ten-minute increase
until 60:00
60:00 (Max)
<Example>
• If current time remaining is 12:15, countdown will restart
from 15:00.
• If current time remaining is 9:15, countdown will restart
from 10:00.
Note
• While timer function is in progress, you
can change channels on the unit with
while “CANCEL/SET” screen is
CH
not displayed.
3
Alarm will sound at 0:00.
Press any button to stop.
• The volume of the alarm gradually increases for one
minute and then continues to beep until any button is
pressed.
17
Closed Caption System
Closed Caption is ...
This multi-use system not only allows the hearing impaired to enjoy selected programs, but also makes
useful information from TV stations available to everyone.
Closed Caption Mode Feature
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
LOCK LANGUAGE
TV
CH
EX I T
CLOCK
1) Press
to
select “TV.”
2) Press ACTION to
display SET UP TV
screen.
SELECT :
SET
: ACT I ON
3
SET UP TV
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
FM ANTENNA
: TUNER
: EXT
SELECT :
END
: ACT I ON
1) Press
to select
“CAPTION.”
to display
2) Press
CAPTION screen.
SET :
Closed Caption Mode
Selections
Caption Mode: CAP C1 or C2
A narration of selected
TV programs is displayed.
Check TV program listings for CC
(Closed Caption) broadcasts.
Caption Mode: TEXT C1 or C2
The lower half of the screen will
be blocked out. When the TV
station broadcasts information,
such as program listings, it will
appear in this space.
Caption Mode: OFF
Closed Caption / Text narration
will not be displayed.
NOTES :
4
CAPT I ON
CAPT I ON MODE
CC ON MUTE
: CAP C1
: CAP C1
SELECT :
END
: ACT I ON
SET :
OFF
1) Press
to select
CAPTION MODE.
repeatedly
2) Press
to select mode.
(See left.)
CAP C1
TEXT C2
TEXT C1
• The closed caption or text signal
may be broadcast over C1, C2, or
both. Also, text contents can vary
so you may wish to try different
settings.
• While recording of one station
and watching another is being
done, Captioning will not be
displayed.
CAP C2
5
Press ACTION three times to
return to the normal screen.
Recording and Playing Back a Closed Caption/Text Program
Record:
Record normally.
Closed Caption/ Text signal, if present, is recorded automatically.
Playback: Start playback. Do above steps to select desired caption mode.
18
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Caption On Mute Feature
Closed Caption narration, if available, is displayed when
MUTE button is pressed for silence.
1
MUTE
2
M A I N MENU
LOCK LANGUAGE
TV
CH
EX I T
CLOCK
1) Press
to
select “TV.”
2) Press ACTION to
display SET UP TV
screen.
SELECT :
SET
: ACT I ON
ACTION
3
SET UP TV
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
FM ANTENNA
: TUNER
: EXT
SELECT :
END
: ACT I ON
4
1) Press
to select
“CAPTION.”
to display
2) Press
CAPTION screen.
SET :
CAPT I ON
CAPT I ON MODE
CC ON MUTE
: OFF
: CAP C1
SELECT :
END
: ACT I ON
SET :
TV Operation
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
Press ACTION to display MAIN MENU.
1) Press
to select
CAPTION MODE.
repeatedly to
2) Press
select “OFF.”
to select
CC ON MUTE.
2) Press
repeatedly to
select desired mode.
1) Press
5
SELECT :
END
: ACT I ON
NO
SET :
• Each press of
will change
the display as shown left.
• The caption may be broadcast
over CAP C1 or C2.
CAP C1
CAP C2
6
Press ACTION three times to
return to the normal screen.
7
Press MUTE to mute the sound and display
closed captioning.
• To cancel, press MUTE again.
19
FM Radio
FM Radio is ...
This unit has an FM radio with built-in antenna, 9 station preset, and a band range of 87.5 ~ 108.1 MHz.
You can even set the On-Timer (page 16) to wake up to your favorite radio station.
FM Radio Setup
FM ANTENNA Setup
1
Press FM/TV on the remote or press
TIMER/FM twice on the unit to display FM
radio mode.
2
Press a number
key (1~9) to select
the FM number.
1 2 : 0 0PM
FM 1
87. 5MHz
Make sure FM tuning is done correctly
(see FM Radio Setup).
1
Press ACTION
to display MAIN MENU.
2
M A I N MENU
TV
CH
3
1 2 : 0 0PM
FM 1
8 7. 7MHz
MEMORY : PRESS ADD / DLT KEY
1 2 : 0 0PM
FM 1
8 7. 7MHz
MEMOR I ZED
1) Press CH
to select the
desired radio
station. (Each
press changes
frequency 200
kHz.)
2) Press
ADD/DLT to
set the radio
station.
Hold down CH
or for a few
seconds, then
release to quickly
scan for FM
stations in your
area.
LOCK LANGUAGE
CLOCK
EX I T
1) Press
to select “TV.”
2) Press ACTION
to display SET
UP TV screen.
SELECT :
SET
: ACT I ON
3
4
1) Press
to
select FM
: TUNER
ANTENNA.
: I NT
to
2) Press
select “INT
SELECT :
SET :
(INTERNAL)”
END
: ACT I ON
or “EXT
■ For cable TV users (EXTERNAL)”
whichever
➞ “INT”
■ For antenna users sounds the
best.
➞ “EXT”
SET UP TV
CAPT I ON
INPUT SELECT
V I DEO ADJUST
FM ANTENNA
Press ACTION twice to end setup.
• To cancel, press
CH or while
in search mode.
To Make Corrections,
select station with a number key,
then do step 3 again.
To exit FM mode,
press FM/TV on the remote or
TIMER/FM twice on the unit.
20
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
How to use the FM radio
1
Press FM/TV on the remote or press
TIMER/FM twice on the unit to display FM
radio mode.
2
1 2 : 0 0PM
FM 1
87. 5MHz
Press a Number
key (1~9) to
select a preset FM
number (see “FM
Radio Setup”).
To cancel, press FM/TV on the remote or
TIMER/FM twice on the unit.
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
Notes
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
TIMER/FM
FM/TV
CH
ACTION
TV Operation
• FM radio cannot be recorded on a Video cassette.
• You may get better reception by repositioning the
unit.
• You cannot select FM Radio mode during playback or
record, or while a blue back screen (PROG, ACTION,
MENU) is displayed.
• Once stations are set, the selected station and current
time are displayed when FM Radio mode is entered.
To remove time, press DISPLAY. If DISPLAY is
pressed again, the unit status screen appears.
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
NUMBER
keys
ADD/DLT
21
Timer Recording
You can set up to 8 programs to be recorded while you are
away.
1
2
Press PROG to display SET PROGRAM screen.
SELECT :
END
: PROG
3
1) Press
to select
TIMER
PROGRAMMING.
2) Press to display
screen.
SET PROGRAM
T I MER PROGRAMMING
ON TIMER
DATE
• If a program is already in
, and to
memory, press
select an unused program
number.
SET :
START
STOP
Press
to select and
or to set the
recording DATE.
CH
7 FR I --:-- --:-- -TODAY
SP
-----------------------SELECT :
END
: PROG
Ready Check List
All connections are made.
Your unit is plugged in.
The clock is set to correct time.
The tape is long enough.
The record tab is in place.
• 1~31 = One time
• DAILY = MON~FRI
• WEEKLY SUN~SAT
= Same time once a week
SET :
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
Today’s
Date
AUDIO IN
ACTION
Example
8
7
9
31
SELECT
/
WEEKLY
(SAT)
1
2
6
Selection Order
WEEKLY
(MON)
DAILY
PROG TIMER indicator
WEEKLY
(SUN)
Repeat step 3 to set:
• Start time, Stop time
• Channel (or LINE for outside source)
• Speed (SP, LP, SLP)
4
P
1
2
3
4
DT
day
----
START
9 : 00 p
-- : --- : --- : --
STOP
12 : 00a
-- : --- : --- : --
CH SPD
08 SP
-- --- --- --
CANCEL : ADD / DLT
SELECT :
SET :
END
: PROG
5
22
Press PROG to
end the program.
To Enter More Programs,
press
to select
and to set a blank
program number, and
then repeat step 3.
Press PROG twice to exit this mode.
• If you’re using a cable box, make sure that it is tuned
to the desired channel and the power is left on for timer
recording.
• PROG TIMER indicator lights on the unit.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Cancel a Timer Recording:
(Recording is in progress)
Hold down STOP for a few
seconds to cancel the Timer
Recording.
• Any future daily or weekly recordings
will be performed as programmed.
Review, Replace or Clear Program
Contents : (Recording is not in progress)
Repeat steps 1 and 2 on page 22.
1
2
P
1
2
3
4
DT START STOP CH SPD
day 9 : 00p 12 : 00a 08 SP
8 10 : 00a 12 : 00p 125 SP
10 8 : 00p 9 : 00p 10 SP
SU 9 : 00p 10 : 00p L LP
Press
to select the
desired program.
CANCEL : ADD / DLT
SELECT :
SET :
END
: PROG
3 To Replace program...
DATE
START
STOP
CH
1) Press
to display.
to select
and press or
to set new program
contents.
3) Press PROG.
8 SAT 9:00P 12:00A 08 2) Press
TODAY
SP
----------------------------------------------
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
PROG
SELECT :
END
: PROG
SET :
To Clear program...
STOP
DT START STOP CH SPD
-- -- : -- -- : -- -- -8 10 : 00p 12 : 00a 125 SP
10 8 : 00p 9 : 00p 10 SP
SU 9 : 00p 10 : 00p L LP
Press ADD/DLT.
CANCEL : ADD / DLT
SELECT :
SET :
END
: PROG
4
Press PROG twice to exit this mode.
Timer Operation
P
1
2
3
4
ADD/DLT
Notes
• 2 minutes before Timer recording is performed, “PLEASE
PREPARE FOR TIMER REC” appears and/or the PROG
TIMER Indicator flashes. Be sure a cassette with record tab is
loaded and the unit is in Stop mode.
• If the start times of two programs overlap, the lower numbered
program will have priority.
• If the start time for a Timer Recording comes up during a
normal recording or One Touch Recording (page 12), the Timer
Recording will not be performed.
• If there is a power interruption of more than one minute, the
recording may not be performed or continued.
• If “INCOMPLETE” appears after all items have been set, check
all entries and make necessary corrections.
23
Tape Operation
Search System is ...
Each time a recording is made, an invisible index mark is placed on the tape. When timer recordings are
made, program index and information are also included. These index marks can be used to access or
scan recordings.
Index Search
Go directly to the desired recording.
1
I NDEX SEARCH
ENTER I NDEX NUMBER : 1
US I NG 1- 9 KEYS
FORWARD SEARCH : FF
REVERSE SEARCH : REW
EX I T : SEARCH
Press SEARCH in
Playback or Stop
mode to display
INDEX SEARCH
screen, and then
press number keys
to select the recording
number.
• To calculate number, see
below.
NUMBER Keys
Press FF or REW to
start search.
2
FF
SEARCH
REW
Play begins at
search end.
To search forward
or back 1 index,
press FF or REW
while screen
left in displayed
(10 sec.).
I NDEX SEARCH
FORWARD SEARCH : FF
REVERSE SEARCH : REW
To cancel, press
PLAY.
■ To calculate the Index Number
Example 1:
To go to rec. 2 from rec. 4, enter 3 and press REW.
1
2
3
4
5
6
7
Example 2:
To go to rec. 6 from rec. 2, enter 4 and press FF.
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
1
2
3
4
5
6
7
NOTE: indicates start points of each recording.
FF
REW
Notes
• Make each entry within 10 seconds, or the Index Search
mode will be canceled.
• If Index Search is started very close to an index mark, that
index mark may not be counted in the search.
24
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Auto Operation Functions
■ Auto Shut Off
No broadcast signal in TV (Only when
Weak Signal Display is set to OFF),
blank tape is Played for 5 minutes
➞ Power turns off
• This feature is canceled if any button is
pressed during above mode.
■ Auto Playback
Insert a tape in Power off mode
➞ Power turns on
• Playback begins if tape has no record tab.
■ Auto Rewind
Tape reaches its end
➞ Rewind ➞ Stop
■ Playback Auto Eject (Repeat Play is “OFF”)
Tape with no record tab reaches its end
Rewind ➞ Stop ➞ Eject
Tape Position Display
To find out present tape position.
Tape position is displayed for VHS-C Cassettes
type, tapes under 30 minutes, and some other
tapes, but the position is not correct.
1
Press TAPE POSITION to detect current tape
position.
• “DETECTING TAPE
POSITION” only appears the
first time a cassette is inserted
and it takes several seconds
for correct indication to appear.
• The present tape position
indication is displayed.
TAPE
POSITION
BEG I N
2
END
Advanced Operation
DETECT I NG TAPE POS I T I ON
Press TAPE POSITION (or wait 5 seconds)
to return to the normal screen.
25
Tape Operation (continued)
Commercial Skip
Zero Search
To quickly return to a specific tape counter
location.
1
Press COUNTER RESET during
playback to display the Counter.
By pressing the CM/ZERO button in Playback
mode you can skip over 1 to 3 minutes of recorded
tape in just a few seconds.
Press CM/ZERO repeatedly to select skip
time in Play mode.
• No indication appears.
2
0 : 00 : 00
Press COUNTER
RESET at the
desired position to
reset to “0:00:00.”
3
Continue playback, rewind, or fast
forward.
4
Press STOP.
5
1 : 23 : 45
DISPLAY
Press CM/ZERO in
stop mode to start
ZERO SEARCH.
• Unit goes into FF or REW mode and stops at the last
point the Counter was set to 0:00:00.
REW
PLAY
FF
STOP
CM/ZERO
COUNTER
RESET
26
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Repeat Play
Set to see a recording over and over.
PLAY
REPEAT ON
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
PLAY
REPEAT OFF
In PLAY
mode, press
PLAY/REPEAT
on the unit to
Repeat above to
turn “OFF.”
PLAY/REPEAT
Note
• Playback repeats when tape end is reached or
unrecorded portion over 30 seconds is detected.
Advanced Operation
27
Special VCR Features
Weak Signal Display ON/OFF
When “ON” is selected, the picture is displayed even when
a broadcast signal is weak or non-existent.
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
LOCK LANGUAGE
TV
CH
CLOCK
EX I T
1) Press
to
select “CH.”
2) Press ACTION to
display SET UP
CHANNEL screen.
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
SELECT :
SET
: ACT I ON
ACTION
3
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
WEAK S I GNAL D I SPLAY : OFF
SELECT :
END
: ACT I ON
1) Press
to select
WEAK SIGNAL
DISPLAY .
to set “ON” or
2) Press
“OFF.”
SET :
Notes
• “ON” = Picture is displayed regardless of signal condition,
and may not always be clearly visible.
“OFF” = Screen turns solid blue when signal is absent or
weak.
• If unit is connected to equipment which has blue back feature,
selecting “ON” will have no effect on the other equipment.
4
Press ACTION twice to
return to the normal screen.
VCR Lock
All operations are prohibited except Timer recording and
tape eject. Useful for families with small children.
VCR LOCK ACT I VATED
VCR LOCK OFF
In stop mode, hold
down REC on the
unit without a cassette
inserted for 7 seconds
to turn “ON.” Please
ignore NO CASSETTE
warning.
Repeat above with or
without cassette to turn
“OFF.”
• VCR Lock is canceled automatically after about 24 hours if clock
is set.
28
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
REC
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
V-Chip Control Feature
Process of V-Chip Control Feature
Enter Code
Setup
Blocking
V-Chip Control Feature is...
This unit has a built-in V-Chip Control
which allows you to block unwanted TV
usage based on US MOVIES and US TV
PROGRAMS Ratings.
Enter Secret Code
A 4-digit code must be entered to view a blocked program
or change rating settings.
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
TV
CH
LOCK LANGUAGE
CLOCK
1) Press
to select
“LOCK.”
2) Press ACTION to
display screen.
EX I T
SELECT :
SET
: ACT I ON
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
NUMBER Keys
ACTION
ADD/DLT
3
LOCK
ENTER 4-D I G I T CODE
----
1) Press NUMBER keys
to enter your secret
code.
2) Enter same code again
for confirmation.
ENTER : 0 - 9
END
: ACT I ON
• Step 2) not necessary when
changing rating or secret
To Make Corrections
code.
Press repeatedly to move • Take care that you are not
observed entering the secret
the cursor. Press number
code.
keys to make the correction.
LOCK
CONF I RM 4-D I G I T CODE
****
****
RECOGN I ZED
CHANGE CODE : ADD / DLT
CONT I NUE :
END
: ACT I ON
Press to display
US Ratings menu
(see page 30).
Or
Press ACTION
twice to exit.
Advanced Operation
4
Changing your secret code
• You will need your current code. Do steps 1 ~ 3.
In step 4, press ADD/DLT to clear current code.
Repeat steps 3 and 4 to enter new code.
Notes
• DO NOT forget your secret code.
• Once ratings are set, restricted tapes or programs cannot be
accessed unless the secret code is entered.
29
V-Chip Control Feature (continued)
If LOCK menu is not displayed, do “Enter Secret
Code” steps on page 29.
Setup US MOVIES Ratings
1
LOCK
US MOVIES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
END
: ACT I ON
SET :
1) Press
to
select US
MOVIES.
2) Press to set
“ON” or “OFF.”
Process of V-Chip Control Feature
Enter Code
Setup
Setup US TV PROGRAMS Ratings
1
LOCK
US MOVIES
: OFF
CHANGE SETT I NGS
: OFF
US TV PROGRAMS
CHANGE SETT I NGS
NEXT PAGE
SELECT :
END
: ACT I ON
SET :
1) Press
to
select US TV
PROGRAMS.
2) Press to set
“ON” or “OFF.”
■ “ON” ➞V-Chip Control is activated.
■ “OFF” ➞V-Chip Control is deactivated.
Note
■ “ON” ➞V-Chip Control is activated.
■ “OFF” ➞V-Chip Control is deactivated.
Note
• “NEXT PAGE” displays CANADIAN V-Chip setting
menu. Not necessary except when viewing Canadian
tapes or broadcasts.
• “NEXT PAGE” displays CANADIAN V-Chip setting
menu. Not necessary except when viewing Canadian
tapes or broadcasts.
2
LOCK
US MOVIES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
END
: ACT I ON
3
SET :
V I EW NR PROGRAMS? : YES
G
UNLOCKED
PG
PG-13
R
NC-17
X
CONTA I NS NO RAT I NG
SELECT :
SET :
END
: ACT I ON
1) Press
to
select
CHANGE
SETTINGS.
2) Press to
display screen.
2
1) Press
to
select
VIEW NR
PROGRAMS?.
2) Press to set
“YES” or “NO.”
3
4
V I EW NR PROGRAMS? : YES
G
UNLOCKED
PG
PG-13
R
NC-17
X
GENERAL AUD I ENCE
SELECT :
SET :
END
: ACT I ON
Press
to select
and to set ratings
to be blocked. (See
ratings chart next
page.)
LOCK
US MOVIES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
END
: ACT I ON
SET :
V I EW NR PROGRAMS? : YES
UNLOCKED
TV-Y
FV
TV-Y7
TV-G
V S L D
TV-PG
V S L D
TV-1 4
V S L
TV-MA
CONTA I NS NO RAT I NG
SELECT :
SET :
END
: ACT I ON
4
V I EW NR PROGRAMS? : YES
UNLOCKED
TV-Y
FV
TV-Y7
TV-G
V S L D
TV-PG
V S L D
TV-1 4
V S L
TV-MA
FOR ALL CH I LDREN
SELECT :
SET :
END
: ACT I ON
Note
5
Press ACTION to redisplay LOCK menu
and continue with US TV PROGRAMS
Ratings Setup (this page). Or, press
ACTION three times to exit.
1) Press
to
select
CHANGE
SETTINGS.
2) Press to
display screen.
1) Press
to select
VIEW NR
PROGRAMS?.
2) Press to set
“YES” or “NO.”
NR (Not Rated) PROGRAMS
Some TV shows, such as news, sports,
weather, bulletins, emergency information
usually have no ratings.
NR (Not Rated) PROGRAMS
Some movies, such as old movies or foreign
movies usually have no ratings.
• You may select from
standard TV ratings (chart
1), or customize to a specific
content rating (chart 2).
5
30
Blocking
Press
to
select and to set
ratings to be
blocked.
(See ratings charts
next page.)
• Ratings highlighted
in Green will be
blocked. Ratings in
white letters will not
be blocked.
Press ACTION three times to exit this
mode.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Process of V-Chip Control Feature
Enter Code
Setup
Blocking
Blocking Message
<When V-Chip Control is activated>
CH08
PROGRAM RAT I NG EXCEEDED
RAT I NG : PG-1 3
ACCESS CODE
----
• If a program or movie
exceeds the ratings you
have set, a message
will appear on a black
background and sound is
muted.
US MOVIES RATINGS
G
PG
PG-13
ENTER : 0-9
R
To View a Blocked Program / Movie
[Temporarily Deactivate V-Chip Control]
Enter your secret code (ACCESS CODE) in the
Blocking Message screen.
• V-Chip Control is reactivated when power is turned off
or power failure occurs.
[Deactivate V-Chip Control]
Enter your secret code (steps 1-3 page 29). Then,
set US MOVIES and/or US TV PROGRAMS to
and keys. (Ratings set on
“OFF” using
page 30 is retained and will be in effect when
V-Chip Control is activated again.)
DISPLAY
ACTION
X
US TV PROGRAMS RATINGS:Chart 1
TV-Y
FOR ALL CHILDREN:
Content specifically geared to young
viewers ages 2-6.
TV-Y7 FOR AGE 7 AND OLDER:
May contain mild physical or comedic
violence which may frighten children
under 7.
TV-G GENERAL AUDIENCE:
Contains little or no violence, strong
language, or sexual dialogue or
situations.
TV-PG PARENTAL GUIDANCE:
May contain infrequent coarse
language, limited violence, some
suggestive sexual dialogue and
situations.
TV-14 PARENTS CAUTIONED:
May contain sophisticated themes,
sexual situations, strong language, and
more intense violence.
TV-MA MATURE AUDIENCE:
May contain mature themes, profane
language, graphic violence, and sexual
situations.
Advanced Operation
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
NC-17
GENERAL AUDIENCE:
All ages admitted.
PARENTAL GUIDANCE:
Some material may not be suitable for
children.
PARENTS CAUTIONED:
Some material may be inappropriate
for children under 13.
RESTRICTED:
Children under 17 must be
accompanied by a parent or adult.
OVER AGE 17 ONLY:
No one 17 and under admitted.
ADULTS ONLY:
US TV PROGRAMS RATINGS: Chart 2
FV
V
S
L
D
Fantasy Violence
Violence
Sexual Situations
Adult Language
Sexually Suggestive Dialogue
31
On-Screen Display (OSD)
VCR Status & Clock Display
Press DISPLAY to display or remove
the overlay.
Blue Screen Display
Whenever a blank section of a tape comes up in
Play mode, or when the selected channel has no
broadcast signal with the Weak Signal Display set
to “OFF” (see page 28), the screen will turn solid
blue.
Channel
Function Status
Current Time
REC
0 : 25
Rec Time
Remaining
(OTR mode
only, see
page 12.)
Counter
CH08
1 2 : 0 0PM
-0 : 1 2 : 3 4
SP
Channel & Function Display
When a function button is pressed (PLAY, FF, etc.)
or you change channels, the unit mode or channel
number will be displayed.
NO V-CHIP DATA
CH 08
Tape Speed
Warning and Instruction Displays
OSD
32
These displays will alert you to a missed
operation or provide further instructions.
CAUTION
Page
PLEASE SET CLOCK BY
PRESSING ACTION KEY
If you attempt to set or review a Timer Recording, or
set the On-Timer and the Clock is not set...
8 - 11
CHECK CASSETTE RECORD TAB
If you press REC, and a cassette is inserted with no
record tab...
3, 12
TO CANCEL TIMER REC HOLD
DOWN STOP KEY FOR APPROX 3
SEC
If you press STOP during a Timer Recording...
23
NO CASSETTE
If you press PLAY, FF, REW, or REC without a
cassette inserted...
12
PLEASE PREPARE FOR TIMER
REC
If the unit is not in Stop mode or a cassette with
record tab is not inserted two minutes before a Timer
Recording is about to begin...
VIDEO HEADS MAY NEED
CLEANING PLEASE INSERT HEAD
CLEANING CASSETTE OR REFER
TO MANUAL END: PLAY
If head cleaning becomes necessary while playing
back a tape...
VCR LOCK ACTIVATED
If you press a function button other than STOP/EJECT or
POWER while the unit is in VCR Lock mode...
22 - 23
4
28
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Before Requesting Service
Check the following points once again if you are having trouble with your unit.
Power
No power…
Monitor
No picture or sound...
Poor picture with normal sound...
Poor sound with normal picture...
Poor TV reception...
No color or poor color...
Ghost (multiple) images...
TV programs cannot be
watched...
Channel cannot be selected...
VCR
TV program cannot be
recorded...
Timer recording cannot be
performed…
CORRECTION
• Completely insert Power Plug into an AC outlet.
• Set POWER button to ON.
CORRECTION
•
•
•
•
•
•
•
•
Make sure your antenna system (TV or CABLE), is correctly set. (P.8)
Completely insert Power Plug into an AC outlet.
Set POWER button to ON.
Adjust BRIGHTNESS, SHARPNESS, and PICTURE controls in the SET UP TV
menu. (P.15)
Adjust VOLUME control. (P.14)
Adjust SHARPNESS and PICTURE controls in the SET UP TV menu. (P.15)
Adjust TINT and COLOR controls in the SET UP TV menu. (P.15)
Install a directional antenna.
• Make sure the selected channel is in unit’s memory. (P.10, 11)
• Only the channel being recorded can be viewed on this unit.
CORRECTION
•
•
•
•
Make sure your antenna system (TV or CABLE), is correctly set. (P.8)
Make sure cassette record tab is intact. (P.3)
Check that clock is set to current time and date.
Make sure DSS/CABLE box (if used) is left on and tuned to channel to be
recorded.
• Set recording Start/Stop times correctly. (P.22-23)
• Timer recording may not be performed or continued if a power interruption
of more than 1 minute occurs before or during a Timer Recording, even after
power is restored.
No playback picture, or the
playback picture is noisy or
contains streaks...
• Adjust TRACKING control in either direction. (P.4)
• Try Head Cleaning. (P.4)
VCR cannot be controlled...
• Make sure VCR LOCK is set to off. (P.28)
• Make sure unit is not in a Timer Record operation.
Remote Control
Unit cannot be controlled...
CORRECTION
•
•
•
•
Aim remote at remote sensor on unit (P.7) so that signal is unobstructed.
Inspect the remote batteries. (P.3)
Make sure VCR LOCK is set to off. (P.28)
Exposing unit remote sensor to direct fluorescent or outdoor light may cause
signal interference.
ACTION, PROG and FM/TV
buttons cannot be selected...
• Check remote batteries.
Miscellaneous
CORRECTION
• Insert the cassette window side up; record tab facing you.
• Completely insert Power Plug into an AC outlet.
• Try ejecting or inserting the tape again after turning POWER off, then back on.
• Make sure cassette record tab is intact. (P.3)
• To enable Quick Play mechanism, the VCR cylinder will rotate for about 3
minutes. This reduces response time from Stop to Play mode and from Play to
Rewind Search mode.
• Make sure VCR LOCK is set to off. (P.28)
If you cannot resolve the problem, please call the Customer Satisfaction Center for
product assistance at 1-800-211-PANA(7262).
To locate an authorized servicenter call toll free 1-800-211-PANA(7262)
or send e-mail to : [email protected]
For Your Information
Video cassette cannot be
inserted...
Video cassette cannot be
removed...
Tape cannot be ejected or
inserted...
Video cassette ejects when a
recording is started, or the power
is turned off for timer recording...
In Stop mode, the VCR motor
(CYLINDER) continues to
rotate...
VCR cannot be controlled...
33
Limited Warranty
PANASONIC CONSUMER ELECTRONICS
COMPANY, DIVISION OF MATSUSHITA ELECTRIC
CORPORATION OF AMERICA
One Panasonic Way Secaucus, New Jersey 07094
PANASONIC SALES COMPANY, DIVISION OF
MATSUSHITA ELECTRIC OF PUERTO RICO, INC.,
AVE. 65 de Infantería, Km. 9.5 San Gabriel Industrial
Park, Carolina, Puerto Rico 00985
Panasonic/Quasar Video Products
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship, Panasonic
Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”)
will, for the length of the period indicated on the chart below, which starts with the date of original
purchase (“warranty period”), at its option either (a) repair your product with new or refurbished parts, or
(b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the
warrantor.
Product
Camcorder
Parts
One (1) Year (except
CCD Image Sensor)
CCD Image Sensor - 6
(Six) Months
DVD/VCR Deck, One (1) Year
A/V Mixer
TV/VCR, TV/DVD, One (1) Year (except
TV/DVD/VCR
CRT)
Combination
CRT - Two (2) Years
TV/HDR
Combination
Rechargeable
Batteries
(in exchange for
defective item)
Tape
(in exchange for
defective item)
Memory Cards
(in exchange for
defective item)
Labor
Service
Ninety (90) Days Carry-In or Mail-In
Contact Number
1-800-211-PANA(7262)
Ninety (90) Days
Ninety (90) Days Carry-In or Mail-In
1-800-211-PANA(7262)
1-800-211-PANA(7262)
Ninety (90) Days Carry-In: 21″ CRT
and Smaller
In-Home
or
Carry-In:
Ninety (90) Days
22″ CRT and Larger
Ninety (90) Days In-Home or Carry-In 1-888-843-9788
One (1) Year (except
CRT)
CRT - Two (2) Years
Ten (10) Days
Ninety (90) Days
Not Applicable
Carry-In or Mail-In
1-800-211-PANA(7262)
Five (5) Days
Not Applicable
Carry-In or Mail-In
1-800-211-PANA(7262)
Ninety (90) Days
Not Applicable
Carry-In or Mail-In
1-800-211-PANA(7262)
During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period,
there will be no charge for parts. You must carry-in or mail-in your product or arrange for in-home
service, as applicable, during the warranty period.
If non-rechargeable batteries are included, they are not warranted. This warranty only applies to
products purchased and serviced in the United States or Puer to Rico. This warranty is extended only to
the original purchaser of a new product which was not sold “as is.” A purchase receipt or other proof of
the original purchase date is required for warranty service.
Carry-In, Mail-in or In-Home Service
For Carry-In, Mail-In or In-Home Service (as applicable) in the United States call toll free contact
number listed above or visit Panasonic Web Site: http://www.panasonic.com
For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910.
In-Home service, if applicable, requires clear, complete and easy access to the product by the
authorized servicer and does not include removal or re-installation of an installed product. It is possible
that certain in-home repairs will not be completed in-home, but will require that the product, or parts of
the product, be removed for shop diagnosis and/or repair and then returned.
34
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT
COVER normal wear and tear or cosmetic damage, nor does it cover markings or retained images on
the picture tube resulting from viewing fixed images (including, among other things, letterbox pictures
on standard 4:3 screen TV’s, or non-expanded standard 4:3 pictures on wide screen TV’s, or onscreen
data in a stationary and fixed location). The warranty ALSO DOES NOT COVER damages which
occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures
which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty
installation, set-up adjustments, misadjustment of consumer controls, improper maintenance, power
line surge, lightning damage, modification, or commercial use (such as in a hotel, office, restaurant, or
other business), rental use of the product, service by anyone other than a Factory Servicenter or other
Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY
COVERAGE.” THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someone
remove or re-install an installed unit if applicable, or travel to and from the servicer, loss of media or
images, data or other memory or recorded content. The items listed are not exclusive, but are for
illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state
to state. If a problem with this product develops during or after the warranty period, you may contact
your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the warrantor’
s Consumer Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE (INCLUDING COST OF AN IN-HOME SERVICE CALL, WHERE
APPLICABLE) WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR
RESPONSIBILITY.
Customer Services Directory
For Product Information, Operating Assistance, Literature Request, Dealer
Locations, and all Customer Service inquiries please contact:
1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 9 am-7 pm,
EST. or send e-mail : [email protected]
For hearing or speech impaired TTY users, TTY : 1-877-833-8855
Web Site: http://www.panasonic.com
You can purchase parts, accessories or locate your
nearest servicenter by visiting our Web Site.
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory
Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Phone (787)750-4300 Fax (787)768-2910
As of August 2002
For Your Information
Accessory Purchases:
1-800-332-5368 (Customer Orders Only)
For hearing or speech impaired TTY users, TTY : 1-866-605-1277
Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032
(Monday-Friday 6 am-5 pm; Saturday 6 am-10:30 am, PST)
(Visa, MasterCard, Discover Card, American Express, Check)
35
Spanish Quick Use Guide/Guía para rápida consulta
Connexiones/Configuracion Inicial
Ajuste Manual del Reloj
Conecte por favor todas las conexiones del
cable o de la antena antes de turing potencia.
Si el ajuste automático del reloj no se ha
completado, ajuste el reloj manualmente
de la siguiente manera:
Conectando
1) Presione la tecla ACTION en el
control remoto para visualizar la
pantalla del menú RELOJ.
2) Presione ▲▼ para seleccionar
el mes y para ajustar. De
la misma forma, seleccione y
ajuste la fecha, año, hora y DST
(Hora de Verano).
3) Presione dos veces la tecla
ACTION para poner el RELOJ
en marcha y salir.
Para Ant./Cable
Conecte Ant./Cable a la entrada de antena de la
TV (VHF/UHF).
Para Sistema Digital de Satelite (DSS)/
Convertidor de cable
Conecte la salida del convertidor de cable la
“VHF/UHF” con el RF cable.
Realizando Configuracion Inicial
1
Presione COMBO para mode del combo.
Tape el cable electrico de la unidad en el
enchufe de pared de la CA. POWER de la
prensa en el telecontrol o la unidad. La
unidad se adelanta y comienzo auto del
canal y del reloj.
CH AUTO SET PROCEEDING
AUTO CLOCK SET
PROCEEDING
CANCEL : STOP
2
2 / 6 / 2003 THUDST
12 ::00PM
ON
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
AUTO CLOCK SET
IS INCOMPLETE
PLEASE SET CLOCK BY
PRESSING ACTION KEY
Si usa convertidor de
cable, enciendala y
seleccione el Servicio
Publico de Canales de
Television (PBS) en su
horario de uso o tiempo
de su zona. Si utiliza
receptor DSS este debe
de estar apagado.
Selecciones se realizaran
automaticamente cuando
la configuracion termine,
la pantalla siguiente
aparecera.
Si “AUTO CLOCK SET IS
INCOMPLETE” aparece en
pantalla, coloque el tiempo
usando el procedimiento
manual (MANUAL CLOCK
SET), vealo enseguida.
Ajustar de nuevo el reloj
1
2
36
MENU PR I NC I PAL
BLOQUEO IDIOMA
TV
CANAL
REL OJ
SAL I R
ELEG I R :
F I JAR : ACT I ON
3
F I JAR RELOJ
F I JAC I ON AUTOMAT I CA
MANUAL
AJUSTE ZONA HORA : 0
F I JAR :
ELEG I R :
TERM I NAR : ACT I ON
4
FIJAR RELOJ
2 / 6/2003 JUE 12 : 00PM
VERANO:ACT
-----------------------F I JAR :
ELEG I R :
TERM I NAR : ACT I ON
Nota
• Los botones de funciones son inoperantes durante la
Configuración inicial.
• Para retirar un cassette durante el Ajuste automático, pulse
EJECT dos veces en el control remoto o STOP dos veces en el
VCR. En este caso, los ajustes se deben realizar manualmente.
(Vea la p.10 de Libro de operaciones avanzadas).
• Dependiendo de las condiciones, puede que el Ajuste
automático del reloj tarde más de 30 minutos. En ese caso,
pulse STOP para detener la configuración y realice los
ajustes manualmente. (Vea la p.10 de Libro de operaciones
avanzadas).
Presione ACTION para exhiba
el menú.
5
Presione
▲▼
para
seleccionar
“RELOJ,” y
luego
presione
ACTION.
Presione
▲▼ para
seleccionar
“MANUAL”
y luego
presione .
Presione
▲▼ y
para
seleccionar
y ajustar la
hora y la
fecha.
Presione ACTION dos veces
para que el reloj comience a
funcionar y salir desde este
modo.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Operaciones básicas para la
reproducción
1
2
■
■
■
■
■
■
■
■
Inserte un casete.
• El videograbador combinado se enciende
automáticamente.
Presione PLAY.
• La reproducción comienza automá
ticamente si el casete no tiene la lengüeta
para prevención de grabación.
Para encontrar una escena en particular
Búsqueda hacia adelante ➞ Presione FF
Búsqueda hacia atrás ➞ Presione REW
Para ver una imagen fija (congelada) ➞
Presione PAUSE/SLOW
Para ver en cámara lenta ➞ Mantenga pulsado
el botón PAUSE/SLOW en el modo de imagen
fija
Para ver imágenes cuadro a cuadro ➞
Presione PAUSE/SLOW en el modo de imagen
fija
Para parar ➞ Presione STOP
Para rebobinar la cinta ➞ Presione REW
Para hacer avanzar la cinta rápidamente ➞
Presione FF
Para expulsar la cinta ➞ Presione EJECT
en el control remoto o STOP/EJECT en el
videograbador combinado
Operaciones básicas para la
grabación
1
Inserte un casete con la lengüeta
para prevención de grabado.
2
3
Seleccione el canal.
Presione CH ▲▼ o las teclas numé
ricas correspondiente.
Grabación con temporizador
1
2
Exhiba
TEMPORIZADOR.
1) Presione ▲▼
para seleccionar.
2) Presione para
exhibir.
F I JAR PROGRAMAC I ON
TEMPOR l ZADOR
ENCENDIDO AUTOMATICO
F I JAR :
ELEG I R :
TERM I NAR : PROG
• Si ya existe un programa en la memoria, presione ▲
para seleccionar un número de programa sin
▼y
usar.
3
FECHA
INICIO
PARADA CA
7 VIE --:-- --:-- -HOY
SP
-----------------------F I JAR :
ELEG I R :
TERM I NAR : PROG
Ajuste la fecha de
grabación.
1) Presione ▲▼
para seleccionar.
2) Presione o
para ajustar.
• 1 - 31 = Grabación única
• DIARIO = a la misma hora de lunes a viernes
• SEMANAL = a la misma hora una vez a la semana
Fecha de hoy
Repita el paso 3 para ajustar:
hora de comienzo, hora de parada, canal (o LINEA
para una fuente exterior), velocidad (SP, LP, SLP)
• El videograbador combinado se enciende
automáticamente.
Seleccione la velocidad de grabación.
4
Presione SPEED.
SP = reproducción normal
LP = reproducción larga
SLP = reproducción super larga
■ Para parar ➞ Presione STOP.
■ El videograbador combinado deja
de grabar a una hora prefijada.
(Grabación de un toque)
Presione REC repetidamente para
ajustar la hora de grabación (30 min
- 4 horas.)
Grabación normal 0:30 1:00
2:00
CA VEL
08 SP
-- --- --- --
Termine el
programa.
Presione PROG.
5
Salga de este modo.
Presione PROG dos veces.
• Si está usando un decodificador de TV
cable, asegúrese que se encuentra en el
canal deseado y que la alimentación queda
conectada para grabar con temporizador.
• El indicador PROG TIMER se enciende en el
videograbador combinado.
For Your Information
• Para editar partes no deseadas de una grabaci
ón, presione PAUSE/SLOW para hacer una
pausa durante la grabación.
• No podrá ver otro canal durante la grabación.
3:00
FE I N I C PARADA
D I 9 : 00p 12 : 00a
-- -- : -- -- : --- -- : -- -- : --- -- : -- -- : --
Para introducir más programas.
presione ▲▼ y para seleccionar y ajustar
el número de programa en blanco, y luego
repita los pasos 3 y 4.
Comience la grabación.
Presione REC.
4:00
P
1
2
3
4
CANCELAR : ADD/DLT
F I JAR :
ELEG I R :
TERM I NAR : PROG
• La velocidad seleccionada debe aparecer en la
pantalla.
4
Exhiba FIJAR PROGRAMACION.
Presione PROG.
1:30
37
NOTES
38
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
NOTES
39
Index
4
2
5
A
P
Accessories ................................................................ 3
Audio Mute ............................................................... 14
Auto Operation Functions......................................... 25
Phones ..................................................................... 14
Picture Adjustment ................................................... 15
Playback ................................................................... 12
4
4
2
4
6
7
0
9
2
2
9
7
2
7
8
4
2
2
3
5
B
R
Before Requesting Service....................................... 33
Blocking Message .................................................... 31
Blue Screen Display ................................................. 32
Rapid Tune ............................................................... 14
Rec(ord).................................................................... 12
Record/Playback Speed Settings ............................... 4
Remote Control Buttons ............................................. 6
Repeat Play .............................................................. 27
Reset all unit Memory Functions ................................ 9
Reverse Search........................................................ 12
Rewind...................................................................... 12
C
Caption On Mute Feature ......................................... 19
Channel & Function Display ..................................... 32
Channel (SET UP CHANNEL).................................. 10
Clock (SET CLOCK)................................................. 10
Closed Caption Mode Feature.................................. 18
Commercial Skip ...................................................... 26
Connections................................................................ 8
Copy Your Tapes (Dubbing)..................................... 13
Customer Services Directory.................................... 35
D
DST (Daylight Saving Time) ....................................... 4
E
Eject Tape ................................................................ 12
Enter Secret Code .................................................... 29
F
Fast Forward ............................................................ 12
Features for a Quality Picture..................................... 4
FM Radio ............................................................ 20–21
Forward Search ........................................................ 12
Frame by Frame Advance ........................................ 12
Front Panel Indicators ................................................ 7
3
2
3
4
7
7
H
Head Cleaning............................................................ 4
I
Important Safeguards and Precautions ...................... 2
Index Search ............................................................ 24
Initial Setup................................................................. 8
Instant Alarm ............................................................ 17
8
2
L
2
8
6
Language ................................................................. 10
Limited Warranty ................................................ 34–35
Loading the Batteries.................................................. 3
Location of Controls................................................ 6–7
S
Selecting Input Mode................................................ 13
Sleep Timer .............................................................. 17
Slow Motion .............................................................. 12
Spanish Quick Use Guide .................................. 36–37
Special VCR Features .............................................. 28
Specifications ............................................................. 4
Still (Freeze) Picture ................................................. 12
Stop .......................................................................... 12
T
Tape Erasure Prevention............................................ 3
Tape Position Display............................................... 25
Timer Program Review, Replace, Clear ................... 23
Timer Recording ....................................................... 22
Timer Recording Cancellation .................................. 23
Time Zone Adjust ..................................................... 11
TV Operation ............................................................ 14
TV Timer Features.............................................. 16–17
U
Unit, Front View .......................................................... 7
Unit, Rear View........................................................... 7
Using the 100 key..................................................... 14
US MOVIES RATINGS............................................. 31
US TV PROGRAMS RATINGS ................................ 31
V
V-Chip Control Feature....................................... 29–31
VCR Lock ................................................................. 28
VCR Status & Clock Display..................................... 32
W
Warning and Instruction Displays ............................. 32
Weak Signal Display ON/OFF .................................. 28
N
Z
NIGHT Mode ............................................................ 14
Zero Search.............................................................. 26
LSQT0665A
O
ON-TIMER with Alarm .............................................. 16
One Touch Recording .............................................. 12
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus,
New Jersey 07094
Panasonic Sales Company (“PSC”),
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infanteria. Km. 9.5
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
P
Printed in Indonesia
LSQT0665A
S0103-0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement