ARTHUR MARTIN ELECTROLUX AKG601A1OW User Manual

AKG601A1OW
AKG601A1OX
EN
Cooker
User Manual
2
CONTENTS
Safety information
Safety instructions
Product description
Before first use
Hob - Daily use
Hob - Hints and tips
Hob - Care and cleaning
2
4
7
8
8
9
10
Oven - Daily use
Oven - Using the accessories
Oven - Hints and tips
Oven - Care and cleaning
Troubleshooting
Installation
11
12
13
16
18
19
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible for any injuries or damages that are the result of
incorrect installation or usage. Always keep the instructions
in a safe and accessible location for future reference.
Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent disability.
•
•
•
•
•
•
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
Children between 3 and 8 years of age and persons with
very extensive and complex disabilities shall be kept away
unless continuously supervised.
Children of less than 3 years of age should be kept away
unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep children and pets away from the appliance when it
operates or when it cools down. Accessible parts are hot.
3
•
Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
General Safety
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Only a qualified person must install this appliance and
replace the cable.
This appliance is intended for use up to an altitude of 2000
m above sea level.
This appliance is not intended to be used on a ships, boats
or vessels.
Do not install the appliance behind a decorative door in
order to avoid overheating.
Do not install the appliance on a platform.
Do not operate the appliance by means of an external
timer or separate remote-control system.
WARNING: Unattended cooking on a hob with fat or oil
can be dangerous and may result in fire.
NEVER try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire
blanket.
CAUTION: The cooking process has to be supervised. A
short term cooking process has to be supervised
continuously.
WARNING: Danger of fire: Do not store items on the
cooking surfaces.
Do not use a steam cleaner to clean the appliance.
Do not use harsh abrasive cleaners or sharp metal
scrapers to clean the glass door or the glass of hinged lids
of the hob since they can scratch the surface, which may
result in shattering of the glass.
Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they can get
hot.
Remove any spillage from the lid before opening. Let the
hob surface cool down before closing the lid.
4
•
•
•
•
•
•
WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to avoid
touching heating elements.
Always use oven gloves to remove or put in accessories or
ovenware.
Before maintenance cut the power supply.
Ensure that the appliance is switched off before replacing
the lamp to avoid the possibility of electric shock.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service
Centre or similarly qualified persons to avoid an electrical
hazard.
WARNING: Use only hob guards designed by the
manufacturer of the cooking appliance or indicated by the
manufacturer of the appliance in the instructions for use as
suitable or hob guards incorporated in the appliance. The
use of inappropriate guards can cause accidents.
SAFETY INSTRUCTIONS
This appliance is suitable for the following
markets: MA
Installation
WARNING! Only a qualified
person must install this
appliance.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Follow the installation instructions
supplied with the appliance.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Do not pull the appliance by the handle.
• The kitchen cabinet and the recess
must have suitable dimensions.
• Keep the minimum distance from other
appliances and units.
• Make sure that the appliance is
installed below and adjacent safe
structures.
• Parts of the appliance carry current.
Close the appliance with furniture to
prevent touching the dangerous parts.
• The sides of the appliance must stay
adjacent to appliances or units with the
same height.
• Do not install the appliance adjacent to
a door or under a window. This
prevents hot cookware to fall from the
appliance when the door or the window
is opened.
Electrical Connection
WARNING! Risk of fire and
electric shock.
• All electrical connections should be
made by a qualified electrician.
• The appliance must be earthed.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
5
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Do not let mains cables touch or come
near the appliance door, especially
when the door is hot.
• The shock protection of live and
insulated parts must be fastened in
such a way that it cannot be removed
without tools.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
• If the mains socket is loose, do not
connect the mains plug.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
• The electrical installation must have an
isolation device which lets you
disconnect the appliance from the
mains at all poles. The isolation device
must have a contact opening width of
minimum 3 mm.
• Fully close the appliance door, before
you connect the mains plug to the
mains socket.
Gas connection
• All gas connections should be made by
a qualified person.
• Before installation, make sure that the
local distribution conditions (nature of
the gas and gas pressure) and the
adjustment of the appliance are
compatible.
• Make sure that there is air circulation
around the appliance.
• The information about the gas supply is
on the rating plate.
• This appliance is not connected to a
device, which evacuates the products
of combustion. Make sure to connect
the appliance according to current
installation regulations. Pay attention to
requirements regarding adequate
ventilation.
Use
WARNING! Risk of injury and
burns.
Risk of electrical shock.
• This appliance is for household use
only.
• Do not change the specification of this
appliance.
• Make sure that the ventilation openings
are not blocked.
• Do not let the appliance stay
unattended during operation.
• Deactivate the appliance after each
use.
• Be careful when you open the
appliance door while the appliance is in
operation. Hot air can release.
• Do not operate the appliance with wet
hands or when it has contact with
water.
• Do not use the appliance as a work
surface or as a storage surface.
WARNING! Risk of fire and
explosion
• Fats and oil when heated can release
flammable vapours. Keep flames or
heated objects away from fats and oils
when you cook with them.
• The vapours that very hot oil releases
can cause spontaneous combustion.
• Used oil, that can contain food
remnants, can cause fire at a lower
temperature than oil used for the first
time.
• Do not put flammable products or items
that are wet with flammable products
in, near or on the appliance.
• Do not let sparks or open flames to
come in contact with the appliance
when you open the door.
• Open the appliance door carefully. The
use of ingredients with alcohol can
cause a mixture of alcohol and air.
6
WARNING! Risk of damage to
the appliance.
• To prevent damage or discoloration to
the enamel:
– do not put ovenware or other
objects in the appliance directly on
the bottom.
– do not put water directly into the hot
appliance.
– do not keep moist dishes and food
in the appliance after you finish the
cooking.
– be careful when you remove or
install the accessories.
• Discoloration of the enamel or stainless
steel has no effect on the performance
of the appliance.
• Use a deep pan for moist cakes. Fruit
juices cause stains that can be
permanent.
• Do not keep hot cookware on the
control panel.
• Do not let cookware boil dry.
• Be careful not to let objects or
cookware fall on the appliance. The
surface can be damaged.
• Do not activate the cooking zones with
empty cookware or without cookware.
• Do not put aluminium foil on the
appliance or directly on the bottom of
the appliance.
• Cookware made of cast iron, aluminium
or with a damaged bottom can cause
scratches. Always lift these objects up
when you have to move them on the
cooking surface.
• Provide good ventilation in the room
where the appliance is installed.
• Use only stable cookware with the
correct shape and diameter larger than
the dimensions of the burners.
• Make sure the flame does not go out
when you quickly turn the knob from
the maximum to the minimum position.
• Use only the accessories supplied with
the appliance.
• Do not install a flame diffuser on the
burner.
• This appliance is for cooking purposes
only. It must not be used for other
purposes, for example room heating.
Care and Cleaning
WARNING! Risk of injury, fire,
or damage to the appliance.
• Before maintenance, deactivate the
appliance.
Disconnect the mains plug from the
mains socket.
• Make sure the appliance is cold. There
is the risk that the glass panels can
break.
• Replace immediately the door glass
panels when they are damaged.
Contact the Authorised Service Centre.
• Be careful when you remove the door
from the appliance. The door is heavy!
• Fat and food remaining in the appliance
can cause fire.
• Clean regularly the appliance to
prevent the deterioration of the surface
material.
• Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use any abrasive products,
abrasive cleaning pads, solvents or
metal objects.
• If you use an oven spray, obey the
safety instructions on the packaging.
• Do not clean the catalytic enamel (if
applicable) with any kind of detergent.
• Do not clean the burners in the
dishwasher.
Lid
• Do not change the specification of the
lid.
• Clean the lid regularly.
• Do not open the lid, when there are
spills on the surface.
• Before you close the lid turn all burners
off.
• Do not close the lid until the hob and
oven are completely cold.
• Glass lid can shatter, when heated (if
applicable).
7
• Keep children away when the grill is in
use.
• Do not put the oven shelf with food on
the highest shelf level.
• Keep the lid glass open, while the oven
is in operation (if applicable).
Internal lighting
Service
• To repair the appliance contact an
Authorised Service Centre.
• Use original spare parts only.
Disposal
WARNING! Risk of electric
shock.
• The type of light bulb or halogen lamp
used for this appliance is for household
appliances only. Do not use it for house
lighting.
• Before replacing the lamp, disconnect
the appliance from the power supply.
• Only use lamps with the same
specifications.
Gas Grill
WARNING! Risk of fire,
explosion and burns.
WARNING! Risk of injury or
suffocation.
• Contact your municipal authority for
information on how to discard the
appliance correctly.
• Disconnect the appliance from the
mains supply.
• Cut off the mains electrical cable close
to the appliance and dispose of it.
• Remove the door catch to prevent
children or pets from becoming trapped
in the appliance.
• Flat the external gas pipes.
• Do not leave the appliance unattended
during grilling. Accessible parts
become hot.
PRODUCT DESCRIPTION
General overview
1
2
3
4
5
7
5
4
3
2
1
6
7
1
2
3
4
5
6
7
Button for the spark generator
Knob for the heating functions
Button for the lamp
Knobs for the hob
Grill
Lamp
Shelf positions
8
Cooking surface layout
1
2
5
3
1 Auxiliary burner
2 Steam outlet - number and position
depend on the model
3 Semi-rapid burner
4 Semi-rapid burner
5 Rapid burner
4
Accessories
For cookware, cake tins, roasts.
• Wire shelf
BEFORE FIRST USE
WARNING! Refer to Safety
chapters.
Initial Cleaning
Remove all accessories from the oven.
Refer to "Care and cleaning"
chapter.
Clean the oven and the accessories
before first use.
Put the accessories back to their initial
position.
Preheating
Preheat the empty appliance to burn off
the remaining grease.
1. Set the oven function knob to
maximum gas flow position .
Refer to "Oven - Daily use" chapter.
2. Let the appliance operate for
approximately 1 hour.
WARNING! Accessories can
become hotter than usual.
The appliance can emit an odour and
smoke. This is normal. Make sure that the
airflow is sufficient.
Let the oven cool down. Dampen a soft
cloth with warm water and a little mild
washing-up liquid and use this to clean the
oven cavity.
HOB - DAILY USE
WARNING! Refer to Safety
chapters.
Ignition of the hob burner
Always light the burner before
you put on the cookware.
9
WARNING! Be very careful
when you use open fire in the
kitchen environment. The
manufacturer declines any
responsibility in case of the
flame misuse.
The spark generator can start
automatically when you switch
on the mains, after installation
or a power cut. It is normal.
In the absence of electricity you
can ignite the burner manually.
If after some tries the burner
does not light, check if the
crown and its cap are in the
correct position.
If the burner accidentally goes
out, turn the knob to the off
position and try to light the
burner again after minimum 1
minute.
Burner overview
Ignition of a hob burner with the
thermocouple
A
• For manual ignition put the flame near
the burner. Push the knob for the hob
down and turn it counterclockwise to
the maximum gas flow position .
• For ignition with spark generator button
push and hold the spark generator
button . At the same time push the
knob for the hob down and turn it
counterclockwise to the maximum gas
flow position . Release the spark
generator button when burner lights.
Keep the knob for the hob pushed for
equal or less than 10 seconds to let the
thermocouple warm up. If not, the gas
supply is interrupted.
A.
B.
C.
D.
Adjust the flame after it is regular.
Turning the burner off
WARNING! Do not keep the
knob pushed for more than 15
seconds. If the burner does not
light after 15 seconds, release
the knob, turn it into the off
position and try to light the
burner again after minimum 1
minute.
B
C
D
Burner cap
Burner crown
Ignition candle
Thermocouple (if applicable)
To put the flame out, turn the knob to the
off position .
WARNING! Always turn the
flame down or switch it off
before you remove the pans
from the burner.
HOB - HINTS AND TIPS
WARNING! Refer to Safety
chapters.
Cookware
WARNING! Do not put the
same pan on two burners.
10
WARNING! Do not put
unstable or damaged pots on
the burner to prevent spills and
injuries.
CAUTION! Make sure that pot
handles are not above the front
edge of the cooktop.
CAUTION! Make sure that the
pots are placed centrally on the
burner in order to get the
maximum stability and a lower
gas consumption.
Burner
Diameter of cook‐
ware (mm)
Rapid
160 - 260
Semi-rapid
140 - 240
Auxiliary
120 - 180
Energy saving
• If it is possible, always put the lids on
the cookware.
• When the liquid starts to boil, turn down
the flame to barely simmer the liquid.
Diameters of cookware
WARNING! Use cookware with
diameters applicable to the size
of burners.
HOB - CARE AND CLEANING
WARNING! Refer to Safety
chapters.
General information
• Clean the hob after each use.
• Always use cookware with a clean
base.
• Scratches or dark stains on the surface
have no effect on how the hob
operates.
• Use a special cleaner suitable for the
surface of the hob.
• Wash stainless steel parts with water,
and then dry them with a soft cloth.
Cleaning the hob
• Remove immediately: melted plastic,
plastic foil, sugar and food with sugar,
otherwise, the dirt can cause damage
to the hob. Take care to avoid burns.
• Remove when the hob is sufficiently
cool: limescale rings, water rings, fat
stains, shiny metallic discoloration.
Clean the hob with a moist cloth and a
non-abrasive detergent. After cleaning,
wipe the hob dry with a soft cloth.
• To clean the enamelled parts, caps and
crowns, wash them with warm soapy
water and dry them carefully before you
put them back on.
Cleaning the spark plug
This feature is obtained through a ceramic
ignition candle with a metal electrode.
Keep these components well clean to
prevent difficult lighting and check that the
burner crown holes are not obstructed.
Pan supports
The pan supports are not
resistant to washing in a
dishwasher. They must be
washed by hand.
1. Remove the pan supports to easily
clean the hob.
Be very careful when you
replace the pan supports to
prevent the hob top from
damage.
2. The enamel coating occasionally can
have rough edges, so be careful when
11
you wash the pan supports by hand
and dry them. If necessary, remove
stubborn stains with a paste cleaner.
3. After you clean the pan supports,
make sure that they are in correct
positions.
4. For the burner to operate correctly,
make sure that the arms of the pan
supports are aligned with the centre of
the burner.
Periodic maintenance
Speak to your local Authorised Service
Centre periodically to check the conditions
of the gas supply pipe and the pressure
adjuster, if fitted.
OVEN - DAILY USE
WARNING! Refer to Safety
chapters.
Oven Functions
Oven function
Application
Off position
The oven is off.
Maximum gas supply
To adjust the oven temperature - highest setting.
Minimum gas supply
To adjust the oven temperature - lowest setting.
Grilling
To grill flat food in the middle of the grill. To make
toast.
Oven lamp
To illuminate the oven interior.
To use this function, press the button for the lamp.
Manual ignition of oven gas
burner
1. Open the oven door.
2. Hold the flame near the hole in the
bottom of the oven cavity.
3. At the same time push the knob for the
oven functions and turn it
counterclockwise to the maximum gas
flow position.
4. When the flame comes on, keep the
knob for the oven functions pushed on
the maximum gas flow position for 15
seconds or less to let the
thermocouple warm up.
Do not keep the knob for the
oven functions pushed for more
than 15 seconds. If the oven
burner does not light after 15
seconds, release the knob for
the oven functions, turn it into
off position, open the oven door
and try to light the oven burner
again after minimum 1 minute.
12
After igniting the oven gas
burner
1. Release the knob for the oven
functions.
2. Close the oven door.
3. Turn the knob for the oven functions to
set the necessary heat setting.
Control the flame trough the holes in the
bottom of the oven.
Turning off the oven burner
To put out the flame, turn the knob to the
off position .
Using the grill
CAUTION! Always keep the
appliance door closed when
the grill operates.
The grill temperature cannot be
adjusted. To get a lower
temperature or slower cooking
time, lower the grill pan away
from the flame.
1. Open the oven door.
2. Ignite the grill burner.
• For manual ignition hold a flame
near the grill burner holes. Push
and turn the knob for the grill to the
flame position. Hold the knob
pushed down.
3. Hold the knob for the grill pushed for
approximately 15 seconds.
4. Release the oven control knob.
If the grill does not come on or if it
accidentally goes out release the knob
for the oven functions and turn it to the
Off position. Open the oven door. After
one minute, try to light the grill again.
5. Preheat the grill for 5 to 10 minutes.
6. Put the oven shelf with the meat on
shelf position 3.
7. Put a baking tray or roasting pan
below, on shelf position 2, to collect
the juices.
Turning off the grill burner
To put out the flame, turn the knob to the
off position .
Do not put the meat directly on
the tray or pan.
CAUTION! Do not put the meat
on the highest shelf level.
There is a risk of fire.
CAUTION! Make sure to turn
the knob for the oven funstions
as far as it goes. Avoid the
intermediary position between
Off and Grill. On the
intermediary positions the
spark generator can remain
active.
OVEN - USING THE ACCESSORIES
WARNING! Refer to Safety
chapters.
Inserting the accessories
Wire shelf:
13
Put the shelf on the correct shelf position.
Make sure it does not touch the back wall
of the oven.
OVEN - HINTS AND TIPS
WARNING! Refer to Safety
chapters.
The temperature and baking
times in the tables are
guidelines only. They depend
on the recipes and the quality
and quantity of the ingredients
used.
General information
• The appliance has five shelf positions.
Count the shelf positions from the
bottom of the appliance floor.
• Moisture can condense in the
appliance or on the door glass panels.
This is normal. Always stand back from
the appliance when you open the
appliance door while cooking. To
decrease the condensation, operate
the appliance for 10 minutes before
cooking.
• Clean the moisture after each use of
the appliance.
• Do not put the objects directly on the
appliance floor and do not put
aluminium foil on the components when
you cook. This can change the baking
results and cause damage to the
enamel.
Baking
• Your oven may bake or roast differently
to the oven you had before. Adapt your
usual settings such as temperature,
cooking time and shelf position to the
values in the tables.
• Use the lower temperature the first
time.
• If you cannot find the settings for a
special recipe, look for the similar one.
• Cakes and pastries at different heights
do not always brown equally at first. If
this occurs, do not change the
temperature setting. The differences
equalize during the baking procedure.
• Trays in the oven can twist during
baking. When the trays become cold
again, the distortions disappear.
Baking cakes
Do not open the oven door before 3/4 of
the set cooking time is up.
Cooking meat and fish
Leave the meat for approximately 15
minutes before carving so that the juice
does not seep out.
To prevent too much smoke in the oven
during roasting, add some water into the
deep pan. To prevent the smoke
condensation, add water each time after it
dries up.
Cooking times
Cooking times depend on the type of food,
its consistency, and volume.
Initially, monitor the performance when
you cook. Find the best settings (heat
setting, cooking time, etc.) for your
cookware, recipes and quantities when
you use this appliance.
14
Cooking tables
To set the desired temperature turn the
knob for the oven to the appropriate
position.
Casseroles
Food
Quantity
(kg)
Tempera‐
ture (°C)
Preheat‐
ing time
(min)
Time (min)
Shelf po‐
sition
Lasagna
1.5 - 2.5
135
10
45 - 55
2
Cannelloni
1.5 - 2.5
135
10
35 - 45
2
Potato gratin
1.5 - 2.5
135
10
80 - 90
2
Macaroni
oven
1.5 - 2.5
135
10
40 - 50
2
Kebab Hala
1.5 - 2.5
135
10
40 - 50
2
Food
Quantity
(kg)
Tempera‐
ture (°C)
Preheat‐
ing time
(min)
Time (min)
Shelf po‐
sition
Sheep
1.5 - 2.0
145
10
80 - 1001)
2
Chicken
1.2 - 1.8
145
10
90 - 1101)
2
Duck
1.8 - 2.5
145
10
80 - 1001)
2
Goose
2.5 - 3.0
145
10
90 - 1001)
2
Rabbit
1.0 - 1.5
145
10
80 - 1001)
2
Beef
1.2 - 1.8
145
10
90 - 1001)
2
Meat
1) Turn over after half of cooking time.
15
Fish
Food
Quantity
(kg)
Tempera‐
ture (°C)
Preheat‐
ing time
(min)
Time (min)
Shelf po‐
sition
Pike
0.8 - 1.5
135
10
50 - 60
2
Dorade
0.4 - 0.7
135
10
35 - 40
2
Trout
0.5 - 1.0
135
10
35 - 45
2
Food
Quantity
(kg)
Tempera‐
ture (°C)
Preheat‐
ing time
(min)
Time (min)
Shelf po‐
sition
Thin
1.0 - 1.2
135
10
25 - 30
1
Thick
1.4 - 1.5
135
10
25 - 30
1
Calzone
1.4 - 1.5
135
10
30 - 35
1
Food
Quantity
(kg)
Tempera‐
ture (°C)
Preheat‐
ing time
(min)
Time (min)
Shelf po‐
sition
Biscuits
0.3 - 0.5
125
10
10 - 20
3
Flat cake
0.6 - 1.0
135
10
25 - 30
2
Orange cake
1.0 - 1.5
125
10
110 - 115
2
Feter Mshal‐
ted
1.0 - 1.5
135
10
50 - 60
1
Salty cake
1.0 - 1.2
135
10
45 - 55
2
Yeast cake
1.0 - 1.5
135
10
40 - 50
2
Apple pie
1.0 - 1.5
135
10
70 - 90
2
Food
Quantity
(kg)
Grill posi‐
tion
Preheat‐
ing time
(min)
Time (min)
Shelf po‐
sition
Sheep chops
0.7 - 1.2
on
10
20 - 25
3
Ribs
1.0 - 1.2
on
10
40 - 50
3
Burgers
2.0 - 2.5
on
10
40 - 50
3
Mackerel
1.2 - 1.5
on
10
25 - 35
3
Pizza
Cakes
Grilling
16
Food
Quantity
(kg)
Grill posi‐
tion
Preheat‐
ing time
(min)
Time (min)
Shelf po‐
sition
Toast brown‐
ing
0.3 - 0.5
on
10
4-8
3
Toast Hawai
0.5 - 1.0
on
10
15 - 20
3
OVEN - CARE AND CLEANING
WARNING! Refer to Safety
chapters.
Notes on cleaning
Clean the front of the oven with a soft
cloth with warm water and a mild cleaning
agent.
To clean metal surfaces, use a dedicated
cleaning agent.
Clean the oven interior after each use. Fat
accumulation or other food remains may
result in a fire.
Clean all accessories after each use and
let them dry. Use a soft cloth with warm
water and a cleaning agent.
Cleaning the oven door
The oven door has two panels of glass
installed one behind the other. To make
the cleaning easier remove the oven door.
WARNING! The oven door can
close if you try to remove the
internal panel of glass when
the door is still assembled.
Do not lose the screws.
1. Open the door fully and hold the two
door hinges.
Clean stubborn dirt with a special oven
cleaner.
If you have nonstick accessories, do not
clean them using aggressive agents,
sharp-edged objects or a dishwasher. It
can cause damage to the nonstick
coating.
Clean the moisture from the cavity after
each use.
Stainless steel or aluminium
ovens
Clean the oven door with a damp cloth or
sponge only. Dry it with a soft cloth.
Do not use steel wool, acids or abrasive
materials as they can damage the oven
surface. Clean the oven control panel with
the same precautions.
2. Lift and turn the levers on the two
hinges.
17
6. Use a spatula made of wood or plastic
or equivalent to open the inner door.
Hold the outer door, and push the
inner door against the top edge of the
door. Lift the inner door.
3
2
2
3. Close the oven door to the first
opening position (halfway). Then pull
forward and remove the door from its
seat.
7. Clean the oven door with water and
soap. Clean inner side of the door. Dry
the oven door carefully.
When the cleaning is completed, install
the glass panels and the oven door. To
install the oven door, do the above steps
in the opposite sequence.
4
4
6
4. Put the door on a soft cloth on a stable
surface.
5. Use a screwdriver to remove 2 screws
from bottom edge of door.
5
5
Replacing the lamp
1
1
WARNING! Risk of electric
shock.
The lamp can be hot.
1. Turn off the oven.
Wait until the oven is cooled down.
2. Disconnect the oven from the mains.
3. Put a cloth on the bottom of the cavity.
18
The back lamp
1. Turn the lamp glass cover to remove it.
2. Clean the glass cover.
3. Replace the lamp with a suitable 300
°C heat-resistant lamp.
4. Install the glass cover.
TROUBLESHOOTING
WARNING! Refer to Safety
chapters.
What to do if...
Problem
Possible cause
Remedy
There is no spark when you
try to activate the spark gen‐
erator.
The hob is not connected to
an electrical supply or it is
connected incorrectly.
Check if the hob is correctly
connected to the electrical
supply. Refer to the connec‐
tion diagram.
There is no spark when you
try to activate the spark gen‐
erator.
The fuse is blown.
Make sure that the fuse is
the cause of the malfunc‐
tion. If the fuse is blown
again and again, contact a
qualified electrician.
There is no spark when you
try to activate the spark gen‐
erator.
Burner cap and crown are
placed incorrectly.
Place the burner cap and
crown correctly.
The flame extinguishes im‐
mediately after ignition.
Thermocouple is not heated
up sufficiently.
After lightning the flame,
keep the spark generator
activated for equal or less
than 10 seconds
The flame ring is uneven.
Burner crown is blocked with
food residues.
Make sure that the injector
is not blocked and the burn‐
er crown is clean.
The burners do not work.
There is no gas supply.
Check the gas connection.
The appliance makes
noises.
Some metal parts of the ap‐
pliance expand and contract
when they heat up or cool
down. The noises are nor‐
mal.
The flame colour is orange
or yellow.
The flame can look orange
or yellow in some areas of
the burner. This is normal.
The lamp does not operate.
The lamp is defective.
Replace the lamp.
19
Problem
Possible cause
Remedy
Steam and condensation
settle on the food and in the
cavity of the oven.
You left the dish in the oven
for too long.
Do not leave the dishes in
the oven for longer than 15 20 minutes after the cooking
process ends.
The oven does not heat up.
The necessary settings are
not set.
Make sure that the settings
are correct.
It takes too long to cook the
dishes or they cook too
quickly.
The temperature is too low
or too high.
Adjust the temperature if
necessary. Follow the ad‐
vice in the user manual.
Service data
If you cannot find a solution to the problem
yourself, contact your dealer or an
Authorised Service Centre.
on the front frame of the oven cavity. Do
not remove the rating plate from the oven
cavity.
The necessary data for the service centre
is on the rating plate. The rating plate is
We recommend that you write the data here:
Model (MOD.)
.........................................
Product number (PNC)
.........................................
Serial number (S.N.)
.........................................
INSTALLATION
WARNING! Refer to Safety
chapters.
Location of the appliance
B
You can install your freestanding
appliance with cabinets on one or two
sides and in the corner.
Keep a distance of about 1 cm
between the appliance and the
back wall to make sure that the
lid opens.
For minimal distances for fitting check the
table.
C
A
D
D
Minimum distances
Dimension
mm
A
400
B
650
C
150
20
Dimension
mm
D
20
Technical data
Appliance class
1
Dimension
mm
Height
850 - 870
Voltage
220 - 240 V
Width
600
Frequency
50 / 60 Hz
Depth
600
Other technical data
Appliance category:
II2H3B/P
LPG:
G30 (3B/P) 28-30 mbar
Natural Gas:
G20 (2H) 20 mbar
Bypass diameters
BURNER
Ø BYPASS 1/100 mm
Auxiliary
29 / 30
Semi-rapid
32
Rapid
42
Oven
50
Grill
50
Gas burners for NATURAL GAS G20 20 mbar
BURNER
NORMAL POW‐
ER kW
REDUCED POWER kW
INJECTOR MARK
1/100 mm
Rapid
3.0
0.75
119
Semi-rapid
2.0
0.45
96
Auxiliary
1.0
0.35
70
Oven
2.5
1.0
104
Grill
2.4
1.5
104
NORMAL POW‐
ER kW
REDUCED POWER kW
INJECTOR MARK
1/100 mm
3.0
0.72
88
Gas burners for LPG G30 28-30 mbar
BURNER
Rapid
21
BURNER
NORMAL POW‐
ER kW
REDUCED POWER kW
INJECTOR MARK
1/100 mm
Semi-rapid
2.0
0.43
71
Auxiliary
1.0
0.35
50
Oven
2.5
1.0
75
Grill
2.4
1.5
75
Gas connection
The gas pipe in the appliance has two
endings. You can connect the gas supply
to either one of them. The pipe that is not
used must be clogged with the pipe
closer, which added to the appliance.
Use a fixed connections or use a flexible
stainless steel pipes in compliance with
the regulation in force. If you use flexible
metallic pipes, make sure they do not
come in touch with mobile parts and they
are not squeezed.
•
•
•
•
it is not longer than 1500 mm,
it has no narrowing anywhere,
it is not twisted or tighten,
it does not get in touch with sharp
edges or corners,
• it's conditions can be easily checked.
When checking the flexible pipe make
sure:
• it does not show cracks, cuts, marks of
burnings on the two ends and on its full
length,
• the material is not hardened, but shows
its correct elasticity,
• the fastening clamps are not rusted,
• expired term is not due.
If one or more defects are visible, do not
repair the pipe, but replace it.
WARNING! When installation
is complete, make sure that the
seal of each pipe fitting does
not leak. To check the seal use
a soap solution, not a flame.
The gas supply ramp is on the rear side of
the control panel.
Flexible nonmetal pipes
connection
If you have an easy access to the
connection, you can use a flexible pipe.
The flexible pipe must be tightly attached
by clamps.
In installation always use the pipe holder
and the gasket. The flexible pipe can be
applied when:
• it can not get hotter than room
temperature, higher than 30 °C,
WARNING! Before you
connect the gas, disconnect
the appliance from the
electricity supply or switch off
the fuse in the fuse box. Close
the primary valve of the gas
supply.
22
Adjustment to different types of
gas
WARNING! Let only an
authorized person do the
adjustment to different types of
gas.
3. Remove the injectors with a socket
spanner 7.
4. Replace injectors with the ones
necessary for the type of gas you use.
If the appliance is set for liquid
gas you can change it to
natural gas, with the correct
injectors.
The gas rate is adjusted to suit.
WARNING! Before you replace
the injectors, make sure that
the gas knobs are in the Off
position. Disconnect the
appliance from the electrical
supply. Let the appliance cool
down. There is a risk of injury.
The appliance is set to default
gas. To change the setting
choose a pipe holder from the
list. Always use the gasket
sealing.
A
B
C
A. Gas connection end
B. Natural Gas pipe holder
C. LPG pipe holder
5. Replace the rating plate (it is near the
gas supply pipe) with the one for the
new type of gas supply.
You can find this plate in
the bag supplied with the
appliance.
If the supply gas pressure is not constant
or it is different from the necessary
pressure, install an applicable pressure
adjuster on the gas supply pipe.
Adjusting the minimum gas
level on the hob burner
1. Disconnect the appliance from the
electricity.
2. Remove the knob for the hob. If there
is no access to the bypass screw
dismount the control panel before
adjustment start.
3. With a thin and flat screwdriver adjust
the bypass screw A.
The model determines the position of
the bypass screw A.
A
Hob injectors replacement
Replace the injectors when you change
the gas type.
1. Remove the pan supports.
2. Remove the caps and crowns of the
burner.
A
23
Changing from natural gas to
liquid gas
A
B
1. Fully tighten the bypass screw.
2. Put the knob back.
Changing from liquid gas to
natural gas
1. Unscrew approximately one turn the
bypass screw position A.
2. Put the knob for the hob back.
3. Connect the appliance to the
electricity.
4.
5.
6.
7.
8.
WARNING! Put the mains
plug into the mains socket
only if all parts are back into
their initial position. There is
a risk of injury.
Light the burner.
Refer to "Hob - Daily use" chapter.
Turn the knob for the hob to the
minimum position.
Remove the knob for the hob again.
Screw on slowly the bypass screw till
the flame becomes minimum and
stable.
Put the knob for the hob back on.
3. Unscrew the screw and slowly pull out
the burner.
1
2
4. Release the burner injector with a 7
mm socket spanner and replace it with
a right one.
Oven injector replacement
1. Remove the bottom plate of the oven
cavity to get access to the oven
burner .
Assemble the burner in a revers
sequence.
2. Carefully remove from the burner the
thermocouple A. Next remove the
spark plug B.
Replace the gas type sticker near the gas
supply ramp with the one related to the
new gas type.
24
Adjusting the minimum gas
level on the oven burner
1. Disconnect the appliance from the
electricity.
2. Remove the knob for the oven
functions. If there is no access to the
bypass screw dismount the control
panel before adjustment start.
3. With a thin and flat screwdriver adjust
the bypass screw A.
The model determines the position of
the bypass screw A.
A
A
Changing from natural gas to
liquid gas
1. Fully tighten the bypass screw.
2. Put the knob back.
3. Connect the appliance to the
electricity.
7. Screw on slowly the bypass screw till
the flame becomes minimum and
stable.
8. Put the knob for the oven functions
back.
9. Set the maximum gas flow position on
the knob for the oven functions and let
the oven heat for at least 10 minutes.
10. Quickly turn the knob for the oven
functions from maximum to the
minimum gas flow position.
Control the flame. Make sure the flame
does not go out when you turn the knob to
the minimum gas flow position. There
must be a small regular flame on the oven
burner crown. If the flame goes out adjust
the oven burner again.
Gas grill injector replacement
1. Release the screws which keep the
grill burner in position A.
A
Changing from liquid gas to
natural gas
1. Unscrew approximately one turn the
bypass screw position A.
2. Put the knob for the oven functions
back.
3. Connect the appliance to the
electricity.
WARNING! Put the mains
plug into the mains socket
only if all parts are back into
their initial position. There is
a risk of injury.
4. Light the burner.
Refer to "Oven - Daily use" chapter.
5. Turn the knob for the oven functions
on the minimum position.
6. Remove the knob for the oven
functions again.
2. Release the burner injector with a 7
mm socket spanner and replace it with
a right one.
3. Assemble the burner in a reverse
sequence. Before you fix the screw,
make sure that the burner is pushed
correctly to the back panel.
25
Test the grill injectors.
Levelling
CAUTION! Remove all the
accessories from the oven.
4. If the floor is not equally flat, use the
adjustable feet on the bottom of the
appliance to set a stable position for
the appliance.
1. Open the lid of the appliance and
disassemble it.
2. Disassemble the pan supports and all
the burner assemblies.
To install all the accessories, do the first
step in an opposite sequence.
Electrical installation
WARNING! The manufacturer
is not responsible if you do not
follow the safety precautions
from Safety chapters.
3. Put the appliance on the sidewall on a
clean and smooth surface. Place each
foot into a separate hole, in the plinth,
and rotate it clockwise.
B
WARNING! The power cable
must not touch the part of the
appliance shaded in the
illustration.
26
ENVIRONMENTAL CONCERNS
not dispose of appliances marked with the
symbol with the household waste.
Return the product to your local recycling
facility or contact your municipal office.
Recycle materials with the symbol . Put
the packaging in relevant containers to
recycle it. Help protect the environment
and human health by recycling waste of
electrical and electronic appliances. Do
*
27
867342040-A-522017