EN
SAFETY INSTRUCTIONS
IMPORTANT TO BE READ AND OBSERVED
Download the complete instruction manual on
http://d
ocs.indesit.eu or call the phone number
shown on the warranty booklet.
This appliance is not for professional use. Do not
use the appliance outdoors.
Before using the appliance, read these safety
instructions. Keep them nearby for future reference.
These instructions and the appliance itself provide
important safety warnings, to be observed at all
times. The manufacturer declines any liability for
failure to observe these safety instructions, for
inappropriate use of the appliance or incorrect
setting of controls.
Very young children (0-3 years) should be kept
away from the appliance. Young children (3-8 years)
should be kept away from the appliance unless
continuously supervised. Children from 8 years old
and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge can use this appliance only if they
are supervised or have been given instructions on
safe use and understand the hazards involved.
Children must not play with the appliance. Cleaning
and user maintenance must not be carried out by
children without supervision.
WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to
avoid touching heating elements.
Children less than 8 years of age shall be kept away
unless continuously supervised.
WARNING: If the hob surface is cracked, do not
use the appliance - risk of electric shock.
WARNING: Danger of fire: Do not store items on
the cooking surfaces.
CAUTION: The cooking process has to be
supervised. A short cooking process has to be
supervised continuously.
WARNING: Unattended cooking on a hob with
fat or oil can be dangerous - risk of fire. NEVER try to
extinguish a fire with water: instead, switch off the
appliance and then cover flame e.g. with a lid or a
fire blanket.
Do not use the hob as a work surface or support.
Keep clothes or other flammable materials away
from the appliance, until all the components have
cooled down completely - risk of fire.
PERMITTED USE
CAUTION: the appliance is not intended to be
operated by means of an external switching device,
such as a timer, or separate remote controlled
system.
This appliance is intended to be used in household
and similar applications such as: staff kitchen areas
in shops, offices and other working environments;
farm houses; by clients in hotels, motels, bed &
breakfast and other residential environments.
No other use is permitted (e.g. heating rooms).
INSTALLATION
The appliance must be handled and installed by
two or more persons - risk of injury. Use protective
gloves to unpack and install - risk of cuts.
Installation, including water supply (if any),
electrical connections and repairs must be carried
out by a qualified technician. Do not repair or replace
any part of the appliance unless specifically stated in
the user manual. Keep children away from the
installation site. After unpacking the appliance,
make sure that it has not been damaged during
transport. In the event of problems, contact the
dealer or your nearest After-sales Service. Once
installed, packaging waste (plastic, styrofoam parts
etc.) must be stored out of reach of children - risk of
suffocation. The appliance must be disconnected
from the power supply before any installation
operation - risk of electric shock. During installation,
make sure the appliance does not damage the
power cable - risk of fire or electric shock. Only
activate the appliance when the installation has
been completed.
Carry out all cabinet cutting operations before
fitting the appliance and remove all wood chips and
sawdust.
If the appliance is not installed above an oven, a
separator panel (not included) must be installed in
the compartment under the appliance.
ELECTRICAL WARNINGS
It must be possible to disconnect the appliance
from the power supply by unplugging it if plug is
accessible, or by a multi-pole switch installed
upstream of the socket in accordance with the
wiring rules and the appliance must be earthed in
conformity with national electrical safety standards.
Do not use extension leads, multiple sockets or
adapters. The electrical components must not be
accessible to the user after installation. Do not use
the appliance when you are wet or barefoot. Do not
operate this appliance if it has a damaged power
cable or plug, if it is not working properly, or if it has
been damaged or dropped.
If the supply cord is damaged, it must be replaced
with an identical one by the manufacturer, its service
agent or similarly qualified persons in order to avoid
a hazard - risk of electric shock.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is switched
off and disconnected from the power supply before
performing any maintenance operation; never use
steam cleaning equipment - risk of electric shock.
Do not use abrasive or corrosive products,
chlorine-based cleaners or pan scourers.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with the recycle
symbol
.
The various parts of the packaging must therefore be disposed of
responsibly and in full compliance with local authority regulations
governing waste disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable materials.
Dispose of it in accordance with local waste disposal regulations.
For further information on the treatment, recovery and recycling of
household electrical appliances, contact your local authority, the
collection service for household waste or the store where you purchased
the appliance. This appliance is marked in compliance with European
Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent
negative consequences for the environment and human health.
The symbol on the product or on the accompanying documentation
indicates that it should not be treated as domestic waste but must be
taken to an appropriate collection center for the recycling of electrical
and electronic equipment.
ENERGY SAVING TIPS
Make the most of your hot plate’s residual heat by switching it off a few
minutes before you finish cooking.
The base of your pot or pan should cover the hot plate completely; a
container that is smaller than the hot plate will cause energy to be wasted.
Cover your pots and pans with tight-fitting lids while cooking and use
as little water as possible. Cooking with the lid off will greatly increase
energy consumption.
Use only flat-bottomed pots and pans.
DECLARATION OF CONFORMITY
This appliance meets the Ecodesign requirements of European
Regulation n. 66/2014, in compliance with the European standard
EN 60350‑2.
EN
INSTALLATION
•
•
•
•
•
•
•
•
•
•
The cooktop must be set into a worktop between 20 mm and 50 mm deep.
There must be nothing between the cooktop and the oven (cross rails, brackets, etc.).
The distance between the lower face of the glass ceramic hob and the cupboard or separating
panel must be at least 20 mm.
If the cooktop is to be installed next to a column unit, leave a distance of at least 100 mm
min. 20 mm
from the edge of the cooktop to the side of the column unit.
For built-in dimensions and installation see the picture in this paragraph.
A minimum distance must be maintained between the hob and the hood above it. Please refer to
the user manual of the hood for more informations.
Apply the supplied gasket to the cooktop (unless it has already been fitted), after having cleaned its surface.
Do not install the cooktop near a dishwasher or washing machine, so that the electronic circuits do not come into contact with steam
or moisture, which could damage them.
If an oven is installed beneath the cooktop, make sure that it is equipped with a cooling system. If the temperature of the electronic circuits
exceeds the maximum permitted temperature, the cooktop will switch off automatically; in this case, wait for a few minutes until the internal
temperature of the electronic circuits reaches a tolerable level, at which point it will be possible to switch the hob on again.
ATTENTION: to install the hob on other surfaces than wood (marble, plastic, ceramic, marble, stone, etc.) remember to ask After Sales
Service for the fixing plates (fig. 2) Code 4819 404 78697.
PLACING THE HOB
Important: remove any protective film before installing the hob.
Make sure that the opening in the worktop for the hob is cut according to the dimensions given in the drawing, paying attention to the tolerance
range. The hob should not be forced into the worktop. Forcing the glass-ceramic top may cause it to crack (even at a later date)!
If the worktop is made of wood, use the spring clips and screws provided. Secure the spring clips (A) (fig. 1) with the screws provided (B) (fig. 1) as
shown, paying attention to the specified distances. Fit the hob into the worktop.
If the worktop is made of marble, plastic, ceramic, stone, etc., the hob must be secured with special brackets (C) (fig. 2). Fit the hob into the
worktop (fig. 1). Place the 4 brackets (C) in position in accordance with the thickness of the worktop as shown in fig. 2. Fasten the 4 screws (D) in the
positions (E) (fig. 2).
30 mm
C
145 ± 1mm
50 mm
A
40 mm
B
D
C
D
1
2
DIMENSIONS AND DISTANCES TO BE MAINTAINED
i
L
Min. 40 cm
Min.10 cm
40 mm
580 X 510 mm
580 mm
0
560 +2 mm
510 mm
0
552 mm
R = Min. 6,5 mm
Max. 16 mm
Min. 50 mm
490 +2 mm
482 mm
D
E
200 mm
Min. 5 cm
C
min 20 mm
ELECTRICAL CONNECTION
Electrical connection must be made before connecting the appliance to the electricity supply.
Installation must be carried out by qualified personnel who know the current safety and installation regulations. Specifically, installation must be
carried out in compliance with the regulations of the local electricity supply company.
Make sure the voltage specified on the data plate located on the bottom of the appliance is the same as that of the home.
Regulations require that the appliance be earthed: use conductors (including the earth conductor) of the appropriate size only.
CONNECTION TO THE TERMINAL BLOCK
For the electrical connection, use an H05-RR-F cable as specified in the table below.
SUPPLY
VOLTAGE
CONDUCTORS
(NUMBER AND SIZE)
230V ~ +
3 x 2,5 mm2
230V 3~ +
4 x 1,5 mm2
400V 3N~ +
5 x 1,5 mm2
400V 2N~ +
4 x 1,5 mm2
F
G
The appliance must be connected to the electricity supply by means of an all-pole disconnect switch with minimum contact gap of 3 mm.
ATTENTION: the power supply cable must be long enough to allow the cooktop to be removed from the worktop and must be positioned so as to
avoid damage or overheating caused by contact with the base.
NOTE: the yellow/green earth wire must be connected to the terminal with the symbol
and must be longer than the other wires.
• Remove approx. 70 mm of the cable sheath from the power supply cable (G).
• Strip approx. 10 mm of sheath from the wires. Insert the cable (G) through the opening in the lid (F).
• Insert the cable into the cable clamp and connect the wires to the terminal block as indicated in the diagram printed on the lid.
• Secure the power supply cable (G) by means of the cable clamp.
• Refit the protection lid (F).
• After the electrical connection, fit the hob from the top and hook it to the support springs, according to the illustration.
PRODUCT DESCRIPTION
1. Radiant cooking zone Ø 145
2. Radiant cooking zone Ø 180
3. Radiant cooking zone Ø 145
1
4
4. Radiant cooking zone Ø 180
5. Rear right cooking zone control knob
5
6. Rear left cooking zone control knob
6
7. Front left cooking zone control knob
7
3
8. Front right cooking zone control knob
8
2
FIRST TIME USE
Before use, remove:
• adhesives stuck on the hob;
• cardboard guards and protective plastic film;
•
check whether the hob has been damaged during transport. If in
doubt, contact the After Sales Service.
EN
DAILY USE
SWITCHING THE HOB ON/OFF
To use the hob, turn the knob(s) clockwise and set it/them to the required
power.
To turn the hob off, turn the knob(s) back to position “0”.
IMPORTANT: To avoid a permanent damage the hob:
• do not use pots with bottoms that are not flat;
• do not use metal pots with enamelled bottom;
• do not place hot pots/pans over the control panel.
ACCESSORY
Child guard AMH 122. This accessory can be
obtained from the After Sales Service under
code number 4819 310 18436 or from your
dealer under reference number 017124.
MAINTENANCE AND CLEANING
Disconnect the appliance from the power supply.
•
•
•
Do not use steam cleaning equipment.
Do not use abrasive sponges or scouring pads as they may damage
the glass.
After each use, clean the hob (when it is cool) to remove any deposits
and stains from food residue.
•
•
•
•
•
Sugar or foods with a high sugar content can damage the hob and
must be immediately removed.
Salt, sugar and sand could scratch the glass surface.
Use a soft cloth, absorbent kitchen paper or a specific hob cleaner
(follow the Manufacturer’s instructions).
Spills of liquid in the cooking zones can cause the pots to move or
vibrate.
After cleaning the hob, dry thoroughly.
TROUBLESHOOTING
If the hob will not operate correctly, before calling the After-Sales Service,
refer to the Troubleshooting Guide to determine the problem.
•
•
•
Read and follow the instructions given in the section “Daily use”.
Check that the electricity supply has not been shut off.
Turn the hob off and on again, to make sure that the problem has
been solved.
•
•
Make sure that the knob is not turned to “0”. Turn the multi-pole
switch to “Off” for a few minutes and then turn it back to “On”.
The hob will not switch off: disconnect the hob immediately from
the power supply.
If after the above checks the fault still occurs, get in touch with the nearest
After Sales Service.
AFTER-SALES SERVICE
In order to receive a more complete assistance, please register your
product on www.indesit.com/register.
•
the service number (number after the word Service on the rating
plate). The service number is also indicated on the guarantee
booklet;
•
•
your full address;
your telephone number.
BEFORE CALLING THE AFTER-SALES SERVICE:
1. See if you can solve the problem by yourself with the help of the
suggestions given in the TROUBLESHOOTING.
2. Switch the appliance off and back on again to see if the fault persists.
IF AFTER THE ABOVE CHECKS THE FAULT STILL OCCURS, GET IN
TOUCH WITH THE NEAREST AFTER-SALES SERVICE.
To receive assistance, call the number shown on the warranty booklet or
follow the instructions on the website www.indesit.com.
When contacting our Client After sales service, always specify:
• a brief description of the fault;
• the type and exact model of the appliance;
Type: XXX
Mod.: XXX
XXXXXXXXXXXXXXXXXXXX
Made in X
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXX
01
XXXX XXX XXXXX
If any repairs are required, please contact an authorized after-sales
service (to guarantee that original spare parts will be used and repairs
carried out correctly).
XX XXXX XXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
400011351890
">
